dm btree: increase rebalance threshold in __rebalance2()

commit 474e559567fa631dea8fb8407ab1b6090c903755 upstream.

We got the following warnings from thin_check during thin-pool setup:

  $ thin_check /dev/vdb
  examining superblock
  examining devices tree
    missing devices: [1, 84]
      too few entries in btree_node: 41, expected at least 42 (block 138, max_entries = 126)
  examining mapping tree

The phenomenon is the number of entries in one node of details_info tree is
less than (max_entries / 3). And it can be easily reproduced by the following
procedures:

  $ new a thin pool
  $ presume the max entries of details_info tree is 126
  $ new 127 thin devices (e.g. 1~127) to make the root node being full
    and then split
  $ remove the first 43 (e.g. 1~43) thin devices to make the children
    reblance repeatedly
  $ stop the thin pool
  $ thin_check

The root cause is that the B-tree removal procedure in __rebalance2()
doesn't guarantee the invariance: the minimal number of entries in
non-root node should be >= (max_entries / 3).

Simply fix the problem by increasing the rebalance threshold to
make sure the number of entries in each child will be greater
than or equal to (max_entries / 3 + 1), so no matter which
child is used for removal, the number will still be valid.

Cc: stable@vger.kernel.org
Signed-off-by: Hou Tao <houtao1@huawei.com>
Acked-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dm mpath: remove harmful bio-based optimization

commit dbaf971c9cdf10843071a60dcafc1aaab3162354 upstream.

Removes the branching for edge-case where no SCSI device handler
exists.  The __map_bio_fast() method was far too limited, by only
selecting a new pathgroup or path IFF there was a path failure, fix this
be eliminating it in favor of __map_bio().  __map_bio()'s extra SCSI
device handler specific MPATHF_PG_INIT_REQUIRED test is not in the fast
path anyway.

This change restores full path selector functionality for bio-based
configurations that don't haave a SCSI device handler.  But it should be
noted that the path selectors do have an impact on performance for
certain networks that are extremely fast (and don't require frequent
switching).

Fixes: 8d47e65948dd ("dm mpath: remove unnecessary NVMe branching in favor of scsi_dh checks")
Cc: stable@vger.kernel.org
Reported-by: Drew Hastings <dhastings@crucialwebhost.com>
Suggested-by: Martin Wilck <mwilck@suse.de>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm: meson: venc: cvbs: fix CVBS mode matching

commit 43cb86799ff03e9819c07f37f72f80f8246ad7ed upstream.

With commit 222ec1618c3ace ("drm: Add aspect ratio parsing in DRM
layer") the drm core started honoring the picture_aspect_ratio field
when comparing two drm_display_modes. Prior to that it was ignored.
When the CVBS encoder driver was initially submitted there was no aspect
ratio check.

Switch from drm_mode_equal() to drm_mode_match() without
DRM_MODE_MATCH_ASPECT_RATIO to fix "kmscube" and X.org output using the
CVBS connector. When (for example) kmscube sets the output mode when
using the CVBS connector it passes HDMI_PICTURE_ASPECT_NONE, making the
drm_mode_equal() fail as it include the aspect ratio.

Prior to this patch kmscube reported:
  failed to set mode: Invalid argument

The CVBS mode checking in the sun4i (drivers/gpu/drm/sun4i/sun4i_tv.c
sun4i_tv_mode_to_drm_mode) and ZTE (drivers/gpu/drm/zte/zx_tvenc.c
tvenc_mode_{pal,ntsc}) drivers don't set the "picture_aspect_ratio" at
all. The Meson VPU driver does not rely on the aspect ratio for the CVBS
output so we can safely decouple it from the hdmi_picture_aspect
setting.

Cc: <stable@vger.kernel.org>
Fixes: 222ec1618c3ace ("drm: Add aspect ratio parsing in DRM layer")
Fixes: bbbe775ec5b5da ("drm: Add support for Amlogic Meson Graphic Controller")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
[narmstrong: squashed with drm: meson: venc: cvbs: deduplicate the meson_cvbs_mode lookup code]
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191208171832.1064772-3-martin.blumenstingl@googlemail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/mgag200: Flag all G200 SE A machines as broken wrt <startadd>

commit 4adf0b49eea926a55fd956ef7d86750f771435ff upstream.

Several MGA G200 SE machines don't respect the value of the startadd
register field. After more feedback on affected machines, neither PCI
subvendor ID nor the internal ID seem to hint towards the bug. All
affected machines have a PCI ID of 0x0522 (i.e., G200 SE A). It was
decided to flag all G200 SE A machines as broken.

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Fixes: 1591fadf857c ("drm/mgag200: Add workaround for HW that does not support 'startadd'")
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: John Donnelly <john.p.donnelly@oracle.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Dave Airlie <airlied@redhat.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: David Airlie <airlied@linux.ie>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: "Y.C. Chen" <yc_chen@aspeedtech.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "José Roberto de Souza" <jose.souza@intel.com>
Cc: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
Cc: dri-devel@lists.freedesktop.org
Cc: <stable@vger.kernel.org> # v5.3+
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Allison Randal <allison@lohutok.net>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Noralf Trønnes" <noralf@tronnes.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20191206081901.9938-1-tzimmermann@suse.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/mgag200: Add workaround for HW that does not support 'startadd'

commit 1591fadf857cdbaf2baa55e421af99a61354713c upstream.

There's at least one system that does not interpret the value of
the device's 'startadd' field correctly, which leads to incorrectly
displayed scanout buffers. Always placing the active scanout buffer
at offset 0 works around the problem.

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reported-by: John Donnelly <john.p.donnelly@oracle.com>
Tested-by: John Donnelly <john.p.donnelly@oracle.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Fixes: 81da87f63a1e ("drm: Replace drm_gem_vram_push_to_system() with kunmap + unpin")
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Dave Airlie <airlied@redhat.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: David Airlie <airlied@linux.ie>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: "Y.C. Chen" <yc_chen@aspeedtech.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "José Roberto de Souza" <jose.souza@intel.com>
Cc: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
Cc: dri-devel@lists.freedesktop.org
Cc: <stable@vger.kernel.org> # v5.3+
Link: https://gitlab.freedesktop.org/drm/misc/issues/7
Link: https://patchwork.freedesktop.org/patch/msgid/20191126101529.20356-4-tzimmermann@suse.de
[drop debugfs_init callback - gregkh]
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/mgag200: Store flags from PCI driver data in device structure

commit d6d437d97d54c85a1a93967b2745e31dff03365a upstream.

The flags field in struct mga_device has been unused so far. We now
use it to store flag bits from the PCI driver.

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Fixes: 81da87f63a1e ("drm: Replace drm_gem_vram_push_to_system() with kunmap + unpin")
Cc: John Donnelly <john.p.donnelly@oracle.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Dave Airlie <airlied@redhat.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: David Airlie <airlied@linux.ie>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: "Y.C. Chen" <yc_chen@aspeedtech.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "José Roberto de Souza" <jose.souza@intel.com>
Cc: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
Cc: dri-devel@lists.freedesktop.org
Cc: <stable@vger.kernel.org> # v5.3+
Link: https://patchwork.freedesktop.org/patch/msgid/20191126101529.20356-3-tzimmermann@suse.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/mgag200: Extract device type from flags

commit 3a8a5aba142a44eaeba0cb0ec1b4a8f177b5e59a upstream.

Adds a conversion function that extracts the device type from the
PCI id-table flags. Allows for storing additional information in the
other flag bits.

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Fixes: 81da87f63a1e ("drm: Replace drm_gem_vram_push_to_system() with kunmap + unpin")
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: John Donnelly <john.p.donnelly@oracle.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Dave Airlie <airlied@redhat.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: David Airlie <airlied@linux.ie>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Emil Velikov <emil.velikov@collabora.com>
Cc: "Y.C. Chen" <yc_chen@aspeedtech.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: "José Roberto de Souza" <jose.souza@intel.com>
Cc: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
Cc: dri-devel@lists.freedesktop.org
Cc: <stable@vger.kernel.org> # v5.3+
Link: https://patchwork.freedesktop.org/patch/msgid/20191126101529.20356-2-tzimmermann@suse.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/panfrost: Fix a race in panfrost_gem_free_object()

commit aed44cbeae2b7674cd155ba5cc6506aafe46a94e upstream.

panfrost_gem_shrinker_scan() might purge a BO (release the sgt and
kill the GPU mapping) that's being freed by panfrost_gem_free_object()
if we don't remove the BO from the shrinker list at the beginning of
panfrost_gem_free_object().

Fixes: 013b65101315 ("drm/panfrost: Add madvise and shrinker support")
Cc: <stable@vger.kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Steven Price <steven.price@arm.com>
Acked-by: Alyssa Rosenzweig <alyssa.rosenzweig@collabora.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20191129135908.2439529-5-boris.brezillon@collabora.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/panfrost: Fix a BO leak in panfrost_ioctl_mmap_bo()

commit 3bb69dbcb9e8430e0cc9990cff427ca3ae25ffdc upstream.

We should release the reference we grabbed when an error occurs.

Fixes: 187d2929206e ("drm/panfrost: Add support for GPU heap allocations")
Cc: <stable@vger.kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Steven Price <steven.price@arm.com>
Acked-by: Alyssa Rosenzweig <alyssa.rosenzweig@collabora.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20191129135908.2439529-4-boris.brezillon@collabora.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/panfrost: Fix a race in panfrost_ioctl_madvise()

commit 70cc77952efebf6722d483cb83cfb563ac9768db upstream.

If 2 threads change the MADVISE property of the same BO in parallel we
might end up with an shmem->madv value that's inconsistent with the
presence of the BO in the shrinker list.

The easiest solution to fix that is to protect the
drm_gem_shmem_madvise() call with the shrinker lock.

Fixes: 013b65101315 ("drm/panfrost: Add madvise and shrinker support")
Cc: <stable@vger.kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Steven Price <steven.price@arm.com>
Acked-by: Alyssa Rosenzweig <alyssa.rosenzweig@collabora.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20191129135908.2439529-3-boris.brezillon@collabora.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dma-buf: Fix memory leak in sync_file_merge()

commit 6645d42d79d33e8a9fe262660a75d5f4556bbea9 upstream.

In the implementation of sync_file_merge() the allocated sync_file is
leaked if number of fences overflows. Release sync_file by goto err.

Fixes: a02b9dc90d84 ("dma-buf/sync_file: refactor fence storage in struct sync_file")
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20191122220957.30427-1-navid.emamdoost@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

vfio/pci: call irq_bypass_unregister_producer() before freeing irq

commit d567fb8819162099035e546b11a736e29c2af0ea upstream.

Since irq_bypass_register_producer() is called after request_irq(), we
should do tear-down in reverse order: irq_bypass_unregister_producer()
then free_irq().

Specifically free_irq() may release resources required by the
irqbypass del_producer() callback.  Notably an example provided by
Marc Zyngier on arm64 with GICv4 that he indicates has the potential
to wedge the hardware:

 free_irq(irq)
   __free_irq(irq)
     irq_domain_deactivate_irq(irq)
       its_irq_domain_deactivate()
         [unmap the VLPI from the ITS]

 kvm_arch_irq_bypass_del_producer(cons, prod)
   kvm_vgic_v4_unset_forwarding(kvm, irq, ...)
     its_unmap_vlpi(irq)
       [Unmap the VLPI from the ITS (again), remap the original LPI]

Signed-off-by: Jiang Yi <giangyi@amazon.com>
Cc: stable@vger.kernel.org # v4.4+
Fixes: 6d7425f109d26 ("vfio: Register/unregister irq_bypass_producer")
Link: https://lore.kernel.org/kvm/20191127164910.15888-1-giangyi@amazon.com
Reviewed-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
[aw: commit log]
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ARM: tegra: Fix FLOW_CTLR_HALT register clobbering by tegra_resume()

commit d70f7d31a9e2088e8a507194354d41ea10062994 upstream.

There is an unfortunate typo in the code that results in writing to
FLOW_CTLR_HALT instead of FLOW_CTLR_CSR.

Cc: <stable@vger.kernel.org>
Acked-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ARM: dts: s3c64xx: Fix init order of clock providers

commit d60d0cff4ab01255b25375425745c3cff69558ad upstream.

fin_pll is the parent of clock-controller@7e00f000, specify
the dependency to ensure proper initialization order of clock
providers.

without this patch:
[    0.000000] S3C6410 clocks: apll = 0, mpll = 0
[    0.000000]  epll = 0, arm_clk = 0

with this patch:
[    0.000000] S3C6410 clocks: apll = 532000000, mpll = 532000000
[    0.000000]  epll = 24000000, arm_clk = 532000000

Cc: <stable@vger.kernel.org>
Fixes: 3f6d439f2022 ("clk: reverse default clk provider initialization order in of_clk_init()")
Signed-off-by: Lihua Yao <ylhuajnu@outlook.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

cifs: Fix retrieval of DFS referrals in cifs_mount()

commit 5bb30a4dd60e2a10a4de9932daff23e503f1dd2b upstream.

Make sure that DFS referrals are sent to newly resolved root targets
as in a multi tier DFS setup.

Signed-off-by: Paulo Alcantara (SUSE) <pc@cjr.nz>
Link: https://lkml.kernel.org/r/05aa2995-e85e-0ff4-d003-5bb08bd17a22@canonical.com
Cc: stable@vger.kernel.org
Tested-by: Matthew Ruffell <matthew.ruffell@canonical.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

CIFS: Fix NULL pointer dereference in mid callback

commit 86a7964be7afaf3df6b64faaa10a7032d2444e51 upstream.

There is a race between a system call processing thread
and the demultiplex thread when mid->resp_buf becomes NULL
and later is being accessed to get credits. It happens when
the 1st thread wakes up before a mid callback is called in
the 2nd one but the mid state has already been set to
MID_RESPONSE_RECEIVED. This causes NULL pointer dereference
in mid callback.

Fix this by saving credits from the response before we
update the mid state and then use this value in the mid
callback rather then accessing a response buffer.

Cc: Stable <stable@vger.kernel.org>
Fixes: ee258d79159afed5 ("CIFS: Move credit processing to mid callbacks for SMB3")
Tested-by: Frank Sorenson <sorenson@redhat.com>
Reviewed-by: Ronnie Sahlberg <lsahlber@redhat.com>
Signed-off-by: Pavel Shilovsky <pshilov@microsoft.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

CIFS: Do not miss cancelled OPEN responses

commit 7b71843fa7028475b052107664cbe120156a2cfc upstream.

When an OPEN command is cancelled we mark a mid as
cancelled and let the demultiplex thread process it
by closing an open handle. The problem is there is
a race between a system call thread and the demultiplex
thread and there may be a situation when the mid has
been already processed before it is set as cancelled.

Fix this by processing cancelled requests when mids
are being destroyed which means that there is only
one thread referencing a particular mid. Also set
mids as cancelled unconditionally on their state.

Cc: Stable <stable@vger.kernel.org>
Tested-by: Frank Sorenson <sorenson@redhat.com>
Reviewed-by: Ronnie Sahlberg <lsahlber@redhat.com>
Signed-off-by: Pavel Shilovsky <pshilov@microsoft.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

CIFS: Close open handle after interrupted close

commit 9150c3adbf24d77cfba37f03639d4a908ca4ac25 upstream.

If Close command is interrupted before sending a request
to the server the client ends up leaking an open file
handle. This wastes server resources and can potentially
block applications that try to remove the file or any
directory containing this file.

Fix this by putting the close command into a worker queue,
so another thread retries it later.

Cc: Stable <stable@vger.kernel.org>
Tested-by: Frank Sorenson <sorenson@redhat.com>
Reviewed-by: Ronnie Sahlberg <lsahlber@redhat.com>
Signed-off-by: Pavel Shilovsky <pshilov@microsoft.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

CIFS: Respect O_SYNC and O_DIRECT flags during reconnect

commit 44805b0e62f15e90d233485420e1847133716bdc upstream.

Currently the client translates O_SYNC and O_DIRECT flags
into corresponding SMB create options when openning a file.
The problem is that on reconnect when the file is being
re-opened the client doesn't set those flags and it causes
a server to reject re-open requests because create options
don't match. The latter means that any subsequent system
call against that open file fail until a share is re-mounted.

Fix this by properly setting SMB create options when
re-openning files after reconnects.

Fixes: 1013e760d10e6: ("SMB3: Don't ignore O_SYNC/O_DSYNC and O_DIRECT flags")
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: Pavel Shilovsky <pshilov@microsoft.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

cifs: Don't display RDMA transport on reconnect

commit 14cc639c17ab0b6671526a7459087352507609e4 upstream.

On reconnect, the transport data structure is NULL and its information is not
available.

Signed-off-by: Long Li <longli@microsoft.com>
Cc: stable@vger.kernel.org
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

cifs: smbd: Return -ECONNABORTED when trasnport is not in connected state

commit acd4680e2bef2405a0e1ef2149fbb01cce7e116c upstream.

The transport should return this error so the upper layer will reconnect.

Signed-off-by: Long Li <longli@microsoft.com>
Cc: stable@vger.kernel.org
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

cifs: smbd: Return -EINVAL when the number of iovs exceeds SMBDIRECT_MAX_SGE

commit 37941ea17d3f8eb2f5ac2f59346fab9e8439271a upstream.

While it's not friendly to fail user processes that issue more iovs
than we support, at least we should return the correct error code so the
user process gets a chance to retry with smaller number of iovs.

Signed-off-by: Long Li <longli@microsoft.com>
Cc: stable@vger.kernel.org
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

cifs: smbd: Add messages on RDMA session destroy and reconnection

commit d63cdbae60ac6fbb2864bd3d8df7404f12b7407d upstream.

Log these activities to help production support.

Signed-off-by: Long Li <longli@microsoft.com>
Cc: stable@vger.kernel.org
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

cifs: smbd: Only queue work for error recovery on memory registration

commit c21ce58eab1eda4c66507897207e20c82e62a5ac upstream.

It's not necessary to queue invalidated memory registration to work queue, as
all we need to do is to unmap the SG and make it usable again. This can save
CPU cycles in normal data paths as memory registration errors are rare and
normally only happens during reconnection.

Signed-off-by: Long Li <longli@microsoft.com>
Cc: stable@vger.kernel.org
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

cifs: smbd: Return -EAGAIN when transport is reconnecting

commit 4357d45f50e58672e1d17648d792f27df01dfccd upstream.

During reconnecting, the transport may have already been destroyed and is in
the process being reconnected. In this case, return -EAGAIN to not fail and
to retry this I/O.

Signed-off-by: Long Li <longli@microsoft.com>
Cc: stable@vger.kernel.org
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

rpmsg: glink: Free pending deferred work on remove

commit 278bcb7300f61785dba63840bd2a8cf79f14554c upstream.

By just cancelling the deferred rx worker during GLINK instance teardown
any pending deferred commands are leaked, so free them.

Fixes: b4f8e52b89f6 ("rpmsg: Introduce Qualcomm RPM glink driver")
Cc: stable@vger.kernel.org
Acked-by: Chris Lew <clew@codeaurora.org>
Tested-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

rpmsg: glink: Don't send pending rx_done during remove

commit c3dadc19b7564c732598b30d637c6f275c3b77b6 upstream.

Attempting to transmit rx_done messages after the GLINK instance is
being torn down will cause use after free and memory leaks. So cancel
the intent_work and free up the pending intents.

With this there are no concurrent accessors of the channel left during
qcom_glink_native_remove() and there is therefor no need to hold the
spinlock during this operation - which would prohibit the use of
cancel_work_sync() in the release function. So remove this.

Fixes: 1d2ea36eead9 ("rpmsg: glink: Add rx done command")
Cc: stable@vger.kernel.org
Acked-by: Chris Lew <clew@codeaurora.org>
Tested-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

rpmsg: glink: Fix rpmsg_register_device err handling

commit f7e714988edaffe6ac578318e99501149b067ba0 upstream.

The device release function is set before registering with rpmsg. If
rpmsg registration fails, the framework will call device_put(), which
invokes the release function. The channel create logic does not need to
free rpdev if rpmsg_register_device() fails and release is called.

Fixes: b4f8e52b89f6 ("rpmsg: Introduce Qualcomm RPM glink driver")
Cc: stable@vger.kernel.org
Tested-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Chris Lew <clew@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

rpmsg: glink: Put an extra reference during cleanup

commit b646293e272816dd0719529dcebbd659de0722f7 upstream.

In a remote processor crash scenario, there is no guarantee the remote
processor sent close requests before it went into a bad state. Remove
the reference that is normally handled by the close command in the
so channel resources can be released.

Fixes: b4f8e52b89f6 ("rpmsg: Introduce Qualcomm RPM glink driver")
Cc: stable@vger.kernel.org
Tested-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Chris Lew <clew@codeaurora.org>
Reported-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

rpmsg: glink: Fix use after free in open_ack TIMEOUT case

commit ac74ea01860170699fb3b6ea80c0476774c8e94f upstream.

Extra channel reference put when remote sending OPEN_ACK after timeout
causes use-after-free while handling next remote CLOSE command.

Remove extra reference put in timeout case to avoid use-after-free.

Fixes: b4f8e52b89f6 ("rpmsg: Introduce Qualcomm RPM glink driver")
Cc: stable@vger.kernel.org
Tested-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Arun Kumar Neelakantam <aneela@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

rpmsg: glink: Fix reuse intents memory leak issue

commit b85f6b601407347f5425c4c058d1b7871f5bf4f0 upstream.

Memory allocated for re-usable intents are not freed during channel
cleanup which causes memory leak in system.

Check and free all re-usable memory to avoid memory leak.

Fixes: 933b45da5d1d ("rpmsg: glink: Add support for TX intents")
Cc: stable@vger.kernel.org
Acked-By: Chris Lew <clew@codeaurora.org>
Tested-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Arun Kumar Neelakantam <aneela@codeaurora.org>
Reported-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

rpmsg: glink: Set tail pointer to 0 at end of FIFO

commit 4623e8bf1de0b86e23a56cdb39a72f054e89c3bd upstream.

When wrapping around the FIFO, the remote expects the tail pointer to
be reset to 0 on the edge case where the tail equals the FIFO length.

Fixes: caf989c350e8 ("rpmsg: glink: Introduce glink smem based transport")
Cc: stable@vger.kernel.org
Signed-off-by: Chris Lew <clew@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

xtensa: fix syscall_set_return_value

commit c2d9aa3b6e56de56c7f1ed9026ca6ec7cfbeef19 upstream.

syscall return value is in the register a2, not a0.

Cc: stable@vger.kernel.org # v5.0+
Fixes: 9f24f3c1067c ("xtensa: implement tracehook functions and enable HAVE_ARCH_TRACEHOOK")
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

xtensa: fix TLB sanity checker

commit 36de10c4788efc6efe6ff9aa10d38cb7eea4c818 upstream.

Virtual and translated addresses retrieved by the xtensa TLB sanity
checker must be consistent, i.e. correspond to the same state of the
checked TLB entry. KASAN shadow memory is mapped dynamically using
auto-refill TLB entries and thus may change TLB state between the
virtual and translated address retrieval, resulting in false TLB
insanity report.
Move read_xtlb_translation close to read_xtlb_virtual to make sure that
read values are consistent.

Cc: stable@vger.kernel.org
Fixes: a99e07ee5e88 ("xtensa: check TLB sanity on return to userspace")
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

gfs2: fix glock reference problem in gfs2_trans_remove_revoke

commit fe5e7ba11fcf1d75af8173836309e8562aefedef upstream.

Commit 9287c6452d2b fixed a situation in which gfs2 could use a glock
after it had been freed. To do that, it temporarily added a new glock
reference by calling gfs2_glock_hold in function gfs2_add_revoke.
However, if the bd element was removed by gfs2_trans_remove_revoke, it
failed to drop the additional reference.

This patch adds logic to gfs2_trans_remove_revoke to properly drop the
additional glock reference.

Fixes: 9287c6452d2b ("gfs2: Fix occasional glock use-after-free")
Cc: stable@vger.kernel.org # v5.2+
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

gfs2: Multi-block allocations in gfs2_page_mkwrite

commit f53056c43063257ae4159d83c425eaeb772bcd71 upstream.

In gfs2_page_mkwrite's gfs2_allocate_page_backing helper, try to
allocate as many blocks at once as we need.  Pass in the size of the
requested allocation.

Fixes: 35af80aef99b ("gfs2: don't use buffer_heads in gfs2_allocate_page_backing")
Cc: stable@vger.kernel.org # v5.3+
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

xtensa: use MEMBLOCK_ALLOC_ANYWHERE for KASAN shadow map

commit e64681b487c897ec871465083bf0874087d47b66 upstream.

KASAN shadow map doesn't need to be accessible through the linear kernel
mapping, allocate its pages with MEMBLOCK_ALLOC_ANYWHERE so that high
memory can be used. This frees up to ~100MB of low memory on xtensa
configurations with KASAN and high memory.

Cc: stable@vger.kernel.org # v5.1+
Fixes: f240ec09bb8a ("memblock: replace memblock_alloc_base(ANYWHERE) with memblock_phys_alloc")
Reviewed-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

block: fix "check bi_size overflow before merge"

commit cc90bc68422318eb8e75b15cd74bc8d538a7df29 upstream.

This partially reverts commit e3a5d8e386c3fb973fa75f2403622a8f3640ec06.

Commit e3a5d8e386c3 ("check bi_size overflow before merge") adds a bio_full
check to __bio_try_merge_page.  This will cause __bio_try_merge_page to fail
when the last bi_io_vec has been reached.  Instead, what we want here is only
the bi_size overflow check.

Fixes: e3a5d8e386c3 ("block: check bi_size overflow before merge")
Cc: stable@vger.kernel.org # v5.4+
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

PM / QoS: Redefine FREQ_QOS_MAX_DEFAULT_VALUE to S32_MAX

commit c6a3aea93571a5393602256d8f74772bd64c8225 upstream.

QOS requests for DEFAULT_VALUE are supposed to be ignored but this is
not the case for FREQ_QOS_MAX. Adding one request for MAX_DEFAULT_VALUE
and one for a real value will cause freq_qos_read_value to unexpectedly
return MAX_DEFAULT_VALUE (-1).

This happens because freq_qos max value is aggregated with PM_QOS_MIN
but FREQ_QOS_MAX_DEFAULT_VALUE is (-1) so it's smaller than other
values.

Fix this by redefining FREQ_QOS_MAX_DEFAULT_VALUE to S32_MAX.

Looking at current users for freq_qos it seems that none of them create
requests for FREQ_QOS_MAX_DEFAULT_VALUE.

Fixes: 77751a466ebd ("PM: QoS: Introduce frequency QoS")
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reported-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Cc: 5.4+ <stable@vger.kernel.org> # 5.4+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

PCI: Apply Cavium ACS quirk to ThunderX2 and ThunderX3

commit f338bb9f0179cb959977b74e8331b312264d720b upstream.

Enhance the ACS quirk for Cavium Processors. Add the root port vendor IDs
for ThunderX2 and ThunderX3 series of processors.

[bhelgaas: add Fixes: and stable tag]
Fixes: f2ddaf8dfd4a ("PCI: Apply Cavium ThunderX ACS quirk to more Root Ports")
Link: https://lore.kernel.org/r/20191111024243.GA11408@dc5-eodlnx05.marvell.com
Signed-off-by: George Cherian <george.cherian@marvell.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Robert Richter <rrichter@marvell.com>
Cc: stable@vger.kernel.org # v4.12+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

PCI: rcar: Fix missing MACCTLR register setting in initialization sequence

commit 7c7e53e1c93df14690bd12c1f84730fef927a6f1 upstream.

The R-Car Gen2/3 manual - available at:

https://www.renesas.com/eu/en/products/microcontrollers-microprocessors/rz/rzg/rzg1m.html#documents

"RZ/G Series User's Manual: Hardware" section

strictly enforces the MACCTLR inizialization value - 39.3.1 - "Initial
Setting of PCI Express":

"Be sure to write the initial value (= H'80FF 0000) to MACCTLR before
enabling PCIETCTLR.CFINIT".

To avoid unexpected behavior and to match the SW initialization sequence
guidelines, this patch programs the MACCTLR with the correct value.

Note that the MACCTLR.SPCHG bit in the MACCTLR register description
reports that "Only writing 1 is valid and writing 0 is invalid" but this
"invalid" has to be interpreted as a write-ignore aka "ignored", not
"prohibited".

Reported-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Fixes: c25da4778803 ("PCI: rcar: Add Renesas R-Car PCIe driver")
Fixes: be20bbcb0a8c ("PCI: rcar: Add the initialization of PCIe link in resume_noirq()")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: <stable@vger.kernel.org> # v5.2+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

PCI: Do not use bus number zero from EA capability

commit 73884a7082f466ce6686bb8dd7e6571dd42313b4 upstream.

As per PCIe r5.0, sec 7.8.5.2, fixed bus numbers of a bridge must be zero
when no function that uses EA is located behind it.  Hence, if EA supplies
bus numbers of zero, assign bus numbers normally.  A secondary bus can
never have a bus number of zero, so setting a bridge's Secondary Bus Number
to zero makes downstream devices unreachable.

[bhelgaas: retain bool return value so "zero is invalid" logic is local]
Fixes: 2dbce5901179 ("PCI: Assign bus numbers present in EA capability for bridges")
Link: https://lore.kernel.org/r/1572850664-9861-1-git-send-email-sundeep.lkml@gmail.com
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org # v5.2+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

PCI/MSI: Fix incorrect MSI-X masking on resume

commit e045fa29e89383c717e308609edd19d2fd29e1be upstream.

When a driver enables MSI-X, msix_program_entries() reads the MSI-X Vector
Control register for each vector and saves it in desc->masked.  Each
register is 32 bits and bit 0 is the actual Mask bit.

When we restored these registers during resume, we previously set the Mask
bit if *any* bit in desc->masked was set instead of when the Mask bit
itself was set:

  pci_restore_state
    pci_restore_msi_state
      __pci_restore_msix_state
        for_each_pci_msi_entry
          msix_mask_irq(entry, entry->masked)   <-- entire u32 word
            __pci_msix_desc_mask_irq(desc, flag)
              mask_bits = desc->masked & ~PCI_MSIX_ENTRY_CTRL_MASKBIT
              if (flag)       <-- testing entire u32, not just bit 0
                mask_bits |= PCI_MSIX_ENTRY_CTRL_MASKBIT
              writel(mask_bits, desc_addr + PCI_MSIX_ENTRY_VECTOR_CTRL)

This means that after resume, MSI-X vectors were masked when they shouldn't
be, which leads to timeouts like this:

  nvme nvme0: I/O 978 QID 3 timeout, completion polled

On resume, set the Mask bit only when the saved Mask bit from suspend was
set.

This should remove the need for 19ea025e1d28 ("nvme: Add quirk for Kingston
NVME SSD running FW E8FK11.T").

[bhelgaas: commit log, move fix to __pci_msix_desc_mask_irq()]
Link: https://bugzilla.kernel.org/show_bug.cgi?id=204887
Link: https://lore.kernel.org/r/20191008034238.2503-1-jian-hong@endlessm.com
Fixes: f2440d9acbe8 ("PCI MSI: Refactor interrupt masking code")
Signed-off-by: Jian-Hong Pan <jian-hong@endlessm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

PCI: Fix Intel ACS quirk UPDCR register address

commit d8558ac8c93d429d65d7490b512a3a67e559d0d4 upstream.

According to documentation [0] the correct offset for the Upstream Peer
Decode Configuration Register (UPDCR) is 0x1014.  It was previously defined
as 0x1114.

d99321b63b1f ("PCI: Enable quirks for PCIe ACS on Intel PCH root ports")
intended to enforce isolation between PCI devices allowing them to be put
into separate IOMMU groups.  Due to the wrong register offset the intended
isolation was not fully enforced.  This is fixed with this patch.

Please note that I did not test this patch because I have no hardware that
implements this register.

[0] https://www.intel.com/content/dam/www/public/us/en/documents/datasheets/4th-gen-core-family-mobile-i-o-datasheet.pdf (page 325)
Fixes: d99321b63b1f ("PCI: Enable quirks for PCIe ACS on Intel PCH root ports")
Link: https://lore.kernel.org/r/7a3505df-79ba-8a28-464c-88b83eefffa6@kernkonzept.com
Signed-off-by: Steffen Liebergeld <steffen.liebergeld@kernkonzept.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Acked-by: Ashok Raj <ashok.raj@intel.com>
Cc: stable@vger.kernel.org # v3.15+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

PCI: pciehp: Avoid returning prematurely from sysfs requests

commit 157c1062fcd86ade3c674503705033051fd3d401 upstream.

A sysfs request to enable or disable a PCIe hotplug slot should not
return before it has been carried out.  That is sought to be achieved by
waiting until the controller's "pending_events" have been cleared.

However the IRQ thread pciehp_ist() clears the "pending_events" before
it acts on them.  If pciehp_sysfs_enable_slot() / _disable_slot() happen
to check the "pending_events" after they have been cleared but while
pciehp_ist() is still running, the functions may return prematurely
with an incorrect return value.

Fix by introducing an "ist_running" flag which must be false before a sysfs
request is allowed to return.

Fixes: 32a8cef274fe ("PCI: pciehp: Enable/disable exclusively from IRQ thread")
Link: https://lore.kernel.org/linux-pci/1562226638-54134-1-git-send-email-wangxiongfeng2@huawei.com
Link: https://lore.kernel.org/r/4174210466e27eb7e2243dd1d801d5f75baaffd8.1565345211.git.lukas@wunner.de
Reported-and-tested-by: Xiongfeng Wang <wangxiongfeng2@huawei.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org # v4.19+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

PCI/PM: Always return devices to D0 when thawing

commit f2c33ccacb2d4bbeae2a255a7ca0cbfd03017b7c upstream.

pci_pm_thaw_noirq() is supposed to return the device to D0 and restore its
configuration registers, but previously it only did that for devices whose
drivers implemented the new power management ops.

Hibernation, e.g., via "echo disk > /sys/power/state", involves freezing
devices, creating a hibernation image, thawing devices, writing the image,
and powering off.  The fact that thawing did not return devices with legacy
power management to D0 caused errors, e.g., in this path:

  pci_pm_thaw_noirq
    if (pci_has_legacy_pm_support(pci_dev)) # true for Mellanox VF driver
      return pci_legacy_resume_early(dev)   # ... legacy PM skips the rest
    pci_set_power_state(pci_dev, PCI_D0)
    pci_restore_state(pci_dev)
  pci_pm_thaw
    if (pci_has_legacy_pm_support(pci_dev))
      pci_legacy_resume
drv->resume
  mlx4_resume
    ...
      pci_enable_msix_range
        ...
  if (dev->current_state != PCI_D0)  # <---
    return -EINVAL;

which caused these warnings:

  mlx4_core a6d1:00:02.0: INTx is not supported in multi-function mode, aborting
  PM: dpm_run_callback(): pci_pm_thaw+0x0/0xd7 returns -95
  PM: Device a6d1:00:02.0 failed to thaw: error -95

Return devices to D0 and restore config registers for all devices, not just
those whose drivers support new power management.

[bhelgaas: also call pci_restore_state() before pci_legacy_resume_early(),
update comment, add stable tag, commit log]
Link: https://lore.kernel.org/r/KU1P153MB016637CAEAD346F0AA8E3801BFAD0@KU1P153MB0166.APCP153.PROD.OUTLOOK.COM
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: stable@vger.kernel.org # v4.13+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

PCI/switchtec: Read all 64 bits of part_event_bitmap

commit 6acdf7e19b37cb3a9258603d0eab315079c19c5e upstream.

The part_event_bitmap register is 64 bits wide, so read it with ioread64()
instead of the 32-bit ioread32().

Fixes: 52eabba5bcdb ("switchtec: Add IOCTLs to the Switchtec driver")
Link: https://lore.kernel.org/r/20190910195833.3891-1-logang@deltatee.com
Reported-by: Doug Meyer <dmeyer@gigaio.com>
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org # v4.12+
Cc: Kelvin Cao <Kelvin.Cao@microchip.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mmc: core: Re-work HW reset for SDIO cards

commit 2ac55d5e5ec9ad0a07e194f0eaca865fe5aa3c40 upstream.

It have turned out that it's not a good idea to unconditionally do a power
cycle and then to re-initialize the SDIO card, as currently done through
mmc_hw_reset() -> mmc_sdio_hw_reset(). This because there may be multiple
SDIO func drivers probed, who also shares the same SDIO card.

To address these scenarios, one may be tempted to use a notification
mechanism, as to allow the core to inform each of the probed func drivers,
about an ongoing HW reset. However, supporting such an operation from the
func driver point of view, may not be entirely trivial.

Therefore, let's use a more simplistic approach to solve the problem, by
instead forcing the card to be removed and re-detected, via scheduling a
rescan-work. In this way, we can rely on existing infrastructure, as the
func driver's ->remove() and ->probe() callbacks, becomes invoked to deal
with the cleanup and the re-initialization.

This solution may be considered as rather heavy, especially if a func
driver doesn't share its card with other func drivers. To address this,
let's keep the current immediate HW reset option as well, but run it only
when there is one func driver probed for the card.

Finally, to allow the caller of mmc_hw_reset(), to understand if the reset
is being asynchronously managed from a scheduled work, it returns 1
(propagated from mmc_sdio_hw_reset()). If the HW reset is executed
successfully and synchronously it returns 0, which maintains the existing
behaviour.

Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Cc: stable@vger.kernel.org # v5.4+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mmc: core: Drop check for mmc_card_is_removable() in mmc_rescan()

commit 99b4ddd8b76a6f60a8c2b3775849d65d21a418fc upstream.

Upfront in mmc_rescan() we use the host->rescan_entered flag, to allow
scanning only once for non-removable cards. Therefore, it's also not
possible that we can have a corresponding card bus attached (host->bus_ops
is NULL), when we are scanning non-removable cards.

For this reason, let' drop the check for mmc_card_is_removable() as it's
redundant.

Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Cc: stable@vger.kernel.org # v5.4+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mmc: block: Add CMD13 polling for MMC IOCTLS with R1B response

commit a0d4c7eb71dd08a89ad631177bb0cbbabd598f84 upstream.

MMC IOCTLS with R1B responses may cause the card to enter the busy state,
which means it's not ready to receive a new request. To prevent new
requests from being sent to the card, use a CMD13 polling loop to verify
that the card returns to the transfer state, before completing the request.

Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mmc: block: Make card_busy_detect() a bit more generic

commit 3869468e0c4800af52bfe1e0b72b338dcdae2cfc upstream.

To prepare for more users of card_busy_detect(), let's drop the struct
request * as an in-parameter and convert to log the error message via
dev_err() instead of pr_err().

Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: Fix incorrect DMA allocations for local memory pool drivers

commit f8c63edfd78905320e86b6b2be2b7a5ac768fa4e upstream.

Fix commit 7b81cb6bddd2 ("usb: add a HCD_DMA flag instead of
guestimating DMA capabilities") where local memory USB drivers
erroneously allocate DMA memory instead of pool memory, causing

OHCI Unrecoverable Error, disabled
HC died; cleaning up

The order between hcd_uses_dma() and hcd->localmem_pool is now
arranged as in hcd_buffer_alloc() and hcd_buffer_free(), with the
test for hcd->localmem_pool placed first.

As an alternative, one might consider adjusting hcd_uses_dma() with

 static inline bool hcd_uses_dma(struct usb_hcd *hcd)
 {
- return IS_ENABLED(CONFIG_HAS_DMA) && (hcd->driver->flags & HCD_DMA);
+ return IS_ENABLED(CONFIG_HAS_DMA) &&
+ (hcd->driver->flags & HCD_DMA) &&
+ (hcd->localmem_pool == NULL);
 }

One can also consider unsetting HCD_DMA for local memory pool drivers.

Fixes: 7b81cb6bddd2 ("usb: add a HCD_DMA flag instead of guestimating DMA capabilities")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Fredrik Noring <noring@nocrew.org>
Link: https://lore.kernel.org/r/20191210172905.GA52526@sx9
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Linux 5.4.5

r8169: add missing RX enabling for WoL on RTL8125

[ Upstream commit 00222d1394104f0fd6c01ca9f578afec9e0f148b ]

RTL8125 also requires to enable RX for WoL.

v2: add missing Fixes tag

Fixes: f1bce4ad2f1c ("r8169: add support for RTL8125")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: mscc: ocelot: unregister the PTP clock on deinit

[ Upstream commit 9385973fe8db9743fa93bf17245635be4eb8c4a6 ]

Currently a switch driver deinit frees the regmaps, but the PTP clock is
still out there, available to user space via /dev/ptpN. Any PTP
operation is a ticking time bomb, since it will attempt to use the freed
regmaps and thus trigger kernel panics:

[    4.291746] fsl_enetc 0000:00:00.2 eth1: error -22 setting up slave phy
[    4.291871] mscc_felix 0000:00:00.5: Failed to register DSA switch: -22
[    4.308666] mscc_felix: probe of 0000:00:00.5 failed with error -22
[    6.358270] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000088
[    6.367090] Mem abort info:
[    6.369888]   ESR = 0x96000046
[    6.369891]   EC = 0x25: DABT (current EL), IL = 32 bits
[    6.369892]   SET = 0, FnV = 0
[    6.369894]   EA = 0, S1PTW = 0
[    6.369895] Data abort info:
[    6.369897]   ISV = 0, ISS = 0x00000046
[    6.369899]   CM = 0, WnR = 1
[    6.369902] user pgtable: 4k pages, 48-bit VAs, pgdp=00000020d58c7000
[    6.369904] [0000000000000088] pgd=00000020d5912003, pud=00000020d5915003, pmd=0000000000000000
[    6.369914] Internal error: Oops: 96000046 [#1] PREEMPT SMP
[    6.420443] Modules linked in:
[    6.423506] CPU: 1 PID: 262 Comm: phc_ctl Not tainted 5.4.0-03625-gb7b2a5dadd7f #204
[    6.431273] Hardware name: LS1028A RDB Board (DT)
[    6.435989] pstate: 40000085 (nZcv daIf -PAN -UAO)
[    6.440802] pc : css_release+0x24/0x58
[    6.444561] lr : regmap_read+0x40/0x78
[    6.448316] sp : ffff800010513cc0
[    6.451636] x29: ffff800010513cc0 x28: ffff002055873040
[    6.456963] x27: 0000000000000000 x26: 0000000000000000
[    6.462289] x25: 0000000000000000 x24: 0000000000000000
[    6.467617] x23: 0000000000000000 x22: 0000000000000080
[    6.472944] x21: ffff800010513d44 x20: 0000000000000080
[    6.478270] x19: 0000000000000000 x18: 0000000000000000
[    6.483596] x17: 0000000000000000 x16: 0000000000000000
[    6.488921] x15: 0000000000000000 x14: 0000000000000000
[    6.494247] x13: 0000000000000000 x12: 0000000000000000
[    6.499573] x11: 0000000000000000 x10: 0000000000000000
[    6.504899] x9 : 0000000000000000 x8 : 0000000000000000
[    6.510225] x7 : 0000000000000000 x6 : ffff800010513cf0
[    6.515550] x5 : 0000000000000000 x4 : 0000000fffffffe0
[    6.520876] x3 : 0000000000000088 x2 : ffff800010513d44
[    6.526202] x1 : ffffcada668ea000 x0 : ffffcada64d8b0c0
[    6.531528] Call trace:
[    6.533977]  css_release+0x24/0x58
[    6.537385]  regmap_read+0x40/0x78
[    6.540795]  __ocelot_read_ix+0x6c/0xa0
[    6.544641]  ocelot_ptp_gettime64+0x4c/0x110
[    6.548921]  ptp_clock_gettime+0x4c/0x58
[    6.552853]  pc_clock_gettime+0x5c/0xa8
[    6.556699]  __arm64_sys_clock_gettime+0x68/0xc8
[    6.561331]  el0_svc_common.constprop.2+0x7c/0x178
[    6.566133]  el0_svc_handler+0x34/0xa0
[    6.569891]  el0_sync_handler+0x114/0x1d0
[    6.573908]  el0_sync+0x140/0x180
[    6.577232] Code: d503201f b00119a1 91022263 b27b7be4 (f9004663)
[    6.583349] ---[ end trace d196b9b14cdae2da ]---
[    6.587977] Kernel panic - not syncing: Fatal exception
[    6.593216] SMP: stopping secondary CPUs
[    6.597151] Kernel Offset: 0x4ada54400000 from 0xffff800010000000
[    6.603261] PHYS_OFFSET: 0xffffd0a7c0000000
[    6.607454] CPU features: 0x10002,21806008
[    6.611558] Memory Limit: none

And now that ocelot->ptp_clock is checked at exit, prevent a potential
error where ptp_clock_register returned a pointer-encoded error, which
we are keeping in the ocelot private data structure. So now,
ocelot->ptp_clock is now either NULL or a valid pointer.

Fixes: 4e3b0468e6d7 ("net: mscc: PTP Hardware Clock (PHC) support")
Cc: Antoine Tenart <antoine.tenart@bootlin.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ionic: keep users rss hash across lif reset

[ Upstream commit ffac2027e18f006f42630f2e01a8a9bd8dc664b5 ]

If the user has specified their own RSS hash key, don't
lose it across queue resets such as DOWN/UP, MTU change,
and number of channels change.  This is fixed by moving
the key initialization to a little earlier in the lif
creation.

Also, let's clean up the RSS config a little better on
the way down by setting it all to 0.

Fixes: aa3198819bea ("ionic: Add RSS support")
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

xdp: obtain the mem_id mutex before trying to remove an entry.

[ Upstream commit 86c76c09898332143be365c702cf8d586ed4ed21 ]

A lockdep splat was observed when trying to remove an xdp memory
model from the table since the mutex was obtained when trying to
remove the entry, but not before the table walk started:

Fix the splat by obtaining the lock before starting the table walk.

Fixes: c3f812cea0d7 ("page_pool: do not release pool until inflight == 0.")
Reported-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Tested-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

page_pool: do not release pool until inflight == 0.

[ Upstream commit c3f812cea0d7006469d1cf33a4a9f0a12bb4b3a3 ]

The page pool keeps track of the number of pages in flight, and
it isn't safe to remove the pool until all pages are returned.

Disallow removing the pool until all pages are back, so the pool
is always available for page producers.

Make the page pool responsible for its own delayed destruction
instead of relying on XDP, so the page pool can be used without
the xdp memory model.

When all pages are returned, free the pool and notify xdp if the
pool is registered with the xdp memory system.  Have the callback
perform a table walk since some drivers (cpsw) may share the pool
among multiple xdp_rxq_info.

Note that the increment of pages_state_release_cnt may result in
inflight == 0, resulting in the pool being released.

Fixes: d956a048cd3f ("xdp: force mem allocator removal and periodic warning")
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net/mlx5e: ethtool, Fix analysis of speed setting

[ Upstream commit 3d7cadae51f1b7f28358e36d0a1ce3f0ae2eee60 ]

When setting speed to 100G via ethtool (AN is set to off), only 25G*4 is
configured while the user, who has an advanced HW which supports
extended PTYS, expects also 50G*2 to be configured.
With this patch, when extended PTYS mode is available, configure
PTYS via extended fields.

Fixes: 4b95840a6ced ("net/mlx5e: Fix matching of speed to PRM link modes")
Signed-off-by: Aya Levin <ayal@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net/mlx5e: Fix translation of link mode into speed

[ Upstream commit 6d485e5e555436d2c13accdb10807328c4158a17 ]

Add a missing value in translation of PTYS ext_eth_proto_oper to its
corresponding speed. When ext_eth_proto_oper bit 10 is set, ethtool
shows unknown speed. With this fix, ethtool shows speed is 100G as
expected.

Fixes: a08b4ed1373d ("net/mlx5: Add support to ext_* fields introduced in Port Type and Speed register")
Signed-off-by: Aya Levin <ayal@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net/mlx5e: Fix freeing flow with kfree() and not kvfree()

[ Upstream commit a23dae79fb6555c808528707c6389345d0b0c189 ]

Flows are allocated with kzalloc() so free with kfree().

Fixes: 04de7dda7394 ("net/mlx5e: Infrastructure for duplicated offloading of TC flows")
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Eli Britstein <elibr@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net/mlx5e: Fix SFF 8472 eeprom length

[ Upstream commit c431f8597863a91eea6024926e0c1b179cfa4852 ]

SFF 8472 eeprom length is 512 bytes. Fix module info return value to
support 512 bytes read.

Fixes: ace329f4ab3b ("net/mlx5e: ethtool, Remove unsupported SFP EEPROM high pages query")
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Aya Levin <ayal@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

act_ct: support asymmetric conntrack

[ Upstream commit 95219afbb980f10934de9f23a3e199be69c5ed09 ]

The act_ct TC module shares a common conntrack and NAT infrastructure
exposed via netfilter.  It's possible that a packet needs both SNAT and
DNAT manipulation, due to e.g. tuple collision.  Netfilter can support
this because it runs through the NAT table twice - once on ingress and
again after egress.  The act_ct action doesn't have such capability.

Like netfilter hook infrastructure, we should run through NAT twice to
keep the symmetry.

Fixes: b57dc7c13ea9 ("net/sched: Introduce action ct")
Signed-off-by: Aaron Conole <aconole@redhat.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net/mlx5e: Fix TXQ indices to be sequential

[ Upstream commit c55d8b108caa2ec1ae8dddd02cb9d3a740f7c838 ]

Cited patch changed (channel index, tc) => (TXQ index) mapping to be a
static one, in order to keep indices consistent when changing number of
channels or TCs.

For 32 channels (OOB) and 8 TCs, real num of TXQs is 256.
When reducing the amount of channels to 8, the real num of TXQs will be
changed to 64.
This indices method is buggy:
- Channel #0, TC 3, the TXQ index is 96.
- Index 8 is not valid, as there is no such TXQ from driver perspective
  (As it represents channel #8, TC 0, which is not valid with the above
  configuration).

As part of driver's select queue, it calls netdev_pick_tx which returns an
index in the range of real number of TXQs. Depends on the return value,
with the examples above, driver could have returned index larger than the
real number of tx queues, or crash the kernel as it tries to read invalid
address of SQ which was not allocated.

Fix that by allocating sequential TXQ indices, and hold a new mapping
between (channel index, tc) => (real TXQ index). This mapping will be
updated as part of priv channels activation, and is used in
mlx5e_select_queue to find the selected queue index.

The existing indices mapping (channel_tc2txq) is no longer needed, as it
is used only for statistics structures and can be calculated on run time.
Delete its definintion and updates.

Fixes: 8bfaf07f7806 ("net/mlx5e: Present SW stats when state is not opened")
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: Fixed updating of ethertype in skb_mpls_push()

[ Upstream commit d04ac224b1688f005a84f764cfe29844f8e9da08 ]

The skb_mpls_push was not updating ethertype of an ethernet packet if
the packet was originally received from a non ARPHRD_ETHER device.

In the below OVS data path flow, since the device corresponding to
port 7 is an l3 device (ARPHRD_NONE) the skb_mpls_push function does
not update the ethertype of the packet even though the previous
push_eth action had added an ethernet header to the packet.

recirc_id(0),in_port(7),eth_type(0x0800),ipv4(tos=0/0xfc,ttl=64,frag=no),
actions:push_eth(src=00:00:00:00:00:00,dst=00:00:00:00:00:00),
push_mpls(label=13,tc=0,ttl=64,bos=1,eth_type=0x8847),4

Fixes: 8822e270d697 ("net: core: move push MPLS functionality from OvS to core helper")
Signed-off-by: Martin Varghese <martin.varghese@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

hsr: fix a NULL pointer dereference in hsr_dev_xmit()

[ Upstream commit df95467b6d2bfce49667ee4b71c67249b01957f7 ]

hsr_dev_xmit() calls hsr_port_get_hsr() to find master node and that would
return NULL if master node is not existing in the list.
But hsr_dev_xmit() doesn't check return pointer so a NULL dereference
could occur.

Test commands:
    ip netns add nst
    ip link add veth0 type veth peer name veth1
    ip link add veth2 type veth peer name veth3
    ip link set veth1 netns nst
    ip link set veth3 netns nst
    ip link set veth0 up
    ip link set veth2 up
    ip link add hsr0 type hsr slave1 veth0 slave2 veth2
    ip a a 192.168.100.1/24 dev hsr0
    ip link set hsr0 up
    ip netns exec nst ip link set veth1 up
    ip netns exec nst ip link set veth3 up
    ip netns exec nst ip link add hsr1 type hsr slave1 veth1 slave2 veth3
    ip netns exec nst ip a a 192.168.100.2/24 dev hsr1
    ip netns exec nst ip link set hsr1 up
    hping3 192.168.100.2 -2 --flood &
    modprobe -rv hsr

Splat looks like:
[  217.351122][ T1635] kasan: CONFIG_KASAN_INLINE enabled
[  217.352969][ T1635] kasan: GPF could be caused by NULL-ptr deref or user memory access
[  217.354297][ T1635] general protection fault: 0000 [#1] SMP DEBUG_PAGEALLOC KASAN PTI
[  217.355507][ T1635] CPU: 1 PID: 1635 Comm: hping3 Not tainted 5.4.0+ #192
[  217.356472][ T1635] Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006
[  217.357804][ T1635] RIP: 0010:hsr_dev_xmit+0x34/0x90 [hsr]
[  217.373010][ T1635] Code: 48 8d be 00 0c 00 00 be 04 00 00 00 48 83 ec 08 e8 21 be ff ff 48 8d 78 10 48 ba 00 b
[  217.376919][ T1635] RSP: 0018:ffff8880cd8af058 EFLAGS: 00010202
[  217.377571][ T1635] RAX: 0000000000000000 RBX: ffff8880acde6840 RCX: 0000000000000002
[  217.379465][ T1635] RDX: dffffc0000000000 RSI: 0000000000000004 RDI: 0000000000000010
[  217.380274][ T1635] RBP: ffff8880acde6840 R08: ffffed101b440d5d R09: 0000000000000001
[  217.381078][ T1635] R10: 0000000000000001 R11: ffffed101b440d5c R12: ffff8880bffcc000
[  217.382023][ T1635] R13: ffff8880bffcc088 R14: 0000000000000000 R15: ffff8880ca675c00
[  217.383094][ T1635] FS:  00007f060d9d1740(0000) GS:ffff8880da000000(0000) knlGS:0000000000000000
[  217.384289][ T1635] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[  217.385009][ T1635] CR2: 00007faf15381dd0 CR3: 00000000d523c001 CR4: 00000000000606e0
[  217.385940][ T1635] Call Trace:
[  217.386544][ T1635]  dev_hard_start_xmit+0x160/0x740
[  217.387114][ T1635]  __dev_queue_xmit+0x1961/0x2e10
[  217.388118][ T1635]  ? check_object+0xaf/0x260
[  217.391466][ T1635]  ? __alloc_skb+0xb9/0x500
[  217.392017][ T1635]  ? init_object+0x6b/0x80
[  217.392629][ T1635]  ? netdev_core_pick_tx+0x2e0/0x2e0
[  217.393175][ T1635]  ? __alloc_skb+0xb9/0x500
[  217.393727][ T1635]  ? rcu_read_lock_sched_held+0x90/0xc0
[  217.394331][ T1635]  ? rcu_read_lock_bh_held+0xa0/0xa0
[  217.395013][ T1635]  ? kasan_unpoison_shadow+0x30/0x40
[  217.395668][ T1635]  ? __kasan_kmalloc.constprop.4+0xa0/0xd0
[  217.396280][ T1635]  ? __kmalloc_node_track_caller+0x3a8/0x3f0
[  217.399007][ T1635]  ? __kasan_kmalloc.constprop.4+0xa0/0xd0
[  217.400093][ T1635]  ? __kmalloc_reserve.isra.46+0x2e/0xb0
[  217.401118][ T1635]  ? memset+0x1f/0x40
[  217.402529][ T1635]  ? __alloc_skb+0x317/0x500
[  217.404915][ T1635]  ? arp_xmit+0xca/0x2c0
[ ... ]

Fixes: 311633b60406 ("hsr: switch ->dellink() to ->ndo_uninit()")
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fixed updating of ethertype in function skb_mpls_pop

[ Upstream commit 040b5cfbcefa263ccf2c118c4938308606bb7ed8 ]

The skb_mpls_pop was not updating ethertype of an ethernet packet if the
packet was originally received from a non ARPHRD_ETHER device.

In the below OVS data path flow, since the device corresponding to port 7
is an l3 device (ARPHRD_NONE) the skb_mpls_pop function does not update
the ethertype of the packet even though the previous push_eth action had
added an ethernet header to the packet.

recirc_id(0),in_port(7),eth_type(0x8847),
mpls(label=12/0xfffff,tc=0/0,ttl=0/0x0,bos=1/1),
actions:push_eth(src=00:00:00:00:00:00,dst=00:00:00:00:00:00),
pop_mpls(eth_type=0x800),4

Fixes: ed246cee09b9 ("net: core: move pop MPLS functionality from OvS to core helper")
Signed-off-by: Martin Varghese <martin.varghese@nokia.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

gre: refetch erspan header from skb->data after pskb_may_pull()

[ Upstream commit 0e4940928c26527ce8f97237fef4c8a91cd34207 ]

After pskb_may_pull() we should always refetch the header
pointers from the skb->data in case it got reallocated.

In gre_parse_header(), the erspan header is still fetched
from the 'options' pointer which is fetched before
pskb_may_pull().

Found this during code review of a KMSAN bug report.

Fixes: cb73ee40b1b3 ("net: ip_gre: use erspan key field for tunnel lookup")
Cc: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Acked-by: William Tu <u9012063@gmail.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

cls_flower: Fix the behavior using port ranges with hw-offload

[ Upstream commit 8ffb055beae58574d3e77b4bf9d4d15eace1ca27 ]

The recent commit 5c72299fba9d ("net: sched: cls_flower: Classify
packets using port ranges") had added filtering based on port ranges
to tc flower. However the commit missed necessary changes in hw-offload
code, so the feature gave rise to generating incorrect offloaded flow
keys in NIC.

One more detailed example is below:

$ tc qdisc add dev eth0 ingress
$ tc filter add dev eth0 ingress protocol ip flower ip_proto tcp \
  dst_port 100-200 action drop

With the setup above, an exact match filter with dst_port == 0 will be
installed in NIC by hw-offload. IOW, the NIC will have a rule which is
equivalent to the following one.

$ tc qdisc add dev eth0 ingress
$ tc filter add dev eth0 ingress protocol ip flower ip_proto tcp \
  dst_port 0 action drop

The behavior was caused by the flow dissector which extracts packet
data into the flow key in the tc flower. More specifically, regardless
of exact match or specified port ranges, fl_init_dissector() set the
FLOW_DISSECTOR_KEY_PORTS flag in struct flow_dissector to extract port
numbers from skb in skb_flow_dissect() called by fl_classify(). Note
that device drivers received the same struct flow_dissector object as
used in skb_flow_dissect(). Thus, offloaded drivers could not identify
which of these is used because the FLOW_DISSECTOR_KEY_PORTS flag was
set to struct flow_dissector in either case.

This patch adds the new FLOW_DISSECTOR_KEY_PORTS_RANGE flag and the new
tp_range field in struct fl_flow_key to recognize which filters are applied
to offloaded drivers. At this point, when filters based on port ranges
passed to drivers, drivers return the EOPNOTSUPP error because they do
not support the feature (the newly created FLOW_DISSECTOR_KEY_PORTS_RANGE
flag).

Fixes: 5c72299fba9d ("net: sched: cls_flower: Classify packets using port ranges")
Signed-off-by: Yoshiki Komachi <komachi.yoshiki@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: sched: allow indirect blocks to bind to clsact in TC

[ Upstream commit 25a443f74bcff2c4d506a39eae62fc15ad7c618a ]

When a device is bound to a clsact qdisc, bind events are triggered to
registered drivers for both ingress and egress. However, if a driver
registers to such a device using the indirect block routines then it is
assumed that it is only interested in ingress offload and so only replays
ingress bind/unbind messages.

The NFP driver supports the offload of some egress filters when
registering to a block with qdisc of type clsact. However, on unregister,
if the block is still active, it will not receive an unbind egress
notification which can prevent proper cleanup of other registered
callbacks.

Modify the indirect block callback command in TC to send messages of
ingress and/or egress bind depending on the qdisc in use. NFP currently
supports egress offload for TC flower offload so the changes are only
added to TC.

Fixes: 4d12ba42787b ("nfp: flower: allow offloading of matches on 'internal' ports")
Signed-off-by: John Hurley <john.hurley@netronome.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: core: rename indirect block ingress cb function

[ Upstream commit dbad3408896c3c5722ec9cda065468b3df16c5bf ]

With indirect blocks, a driver can register for callbacks from a device
that is does not 'own', for example, a tunnel device. When registering to
or unregistering from a new device, a callback is triggered to generate
a bind/unbind event. This, in turn, allows the driver to receive any
existing rules or to properly clean up installed rules.

When first added, it was assumed that all indirect block registrations
would be for ingress offloads. However, the NFP driver can, in some
instances, support clsact qdisc binds for egress offload.

Change the name of the indirect block callback command in flow_offload to
remove the 'ingress' identifier from it. While this does not change
functionality, a follow up patch will implement a more more generic
callback than just those currently just supporting ingress offload.

Fixes: 4d12ba42787b ("nfp: flower: allow offloading of matches on 'internal' ports")
Signed-off-by: John Hurley <john.hurley@netronome.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tcp: Protect accesses to .ts_recent_stamp with {READ,WRITE}_ONCE()

[ Upstream commit 721c8dafad26ccfa90ff659ee19755e3377b829d ]

Syncookies borrow the ->rx_opt.ts_recent_stamp field to store the
timestamp of the last synflood. Protect them with READ_ONCE() and
WRITE_ONCE() since reads and writes aren't serialised.

Use of .rx_opt.ts_recent_stamp for storing the synflood timestamp was
introduced by a0f82f64e269 ("syncookies: remove last_synq_overflow from
struct tcp_sock"). But unprotected accesses were already there when
timestamp was stored in .last_synq_overflow.

Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tcp: tighten acceptance of ACKs not matching a child socket

[ Upstream commit cb44a08f8647fd2e8db5cc9ac27cd8355fa392d8 ]

When no synflood occurs, the synflood timestamp isn't updated.
Therefore it can be so old that time_after32() can consider it to be
in the future.

That's a problem for tcp_synq_no_recent_overflow() as it may report
that a recent overflow occurred while, in fact, it's just that jiffies
has grown past 'last_overflow' + TCP_SYNCOOKIE_VALID + 2^31.

Spurious detection of recent overflows lead to extra syncookie
verification in cookie_v[46]_check(). At that point, the verification
should fail and the packet dropped. But we should have dropped the
packet earlier as we didn't even send a syncookie.

Let's refine tcp_synq_no_recent_overflow() to report a recent overflow
only if jiffies is within the
[last_overflow, last_overflow + TCP_SYNCOOKIE_VALID] interval. This
way, no spurious recent overflow is reported when jiffies wraps and
'last_overflow' becomes in the future from the point of view of
time_after32().

However, if jiffies wraps and enters the
[last_overflow, last_overflow + TCP_SYNCOOKIE_VALID] interval (with
'last_overflow' being a stale synflood timestamp), then
tcp_synq_no_recent_overflow() still erroneously reports an
overflow. In such cases, we have to rely on syncookie verification
to drop the packet. We unfortunately have no way to differentiate
between a fresh and a stale syncookie timestamp.

In practice, using last_overflow as lower bound is problematic.
If the synflood timestamp is concurrently updated between the time
we read jiffies and the moment we store the timestamp in
'last_overflow', then 'now' becomes smaller than 'last_overflow' and
tcp_synq_no_recent_overflow() returns true, potentially dropping a
valid syncookie.

Reading jiffies after loading the timestamp could fix the problem,
but that'd require a memory barrier. Let's just accommodate for
potential timestamp growth instead and extend the interval using
'last_overflow - HZ' as lower bound.

Signed-off-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tcp: fix rejected syncookies due to stale timestamps

[ Upstream commit 04d26e7b159a396372646a480f4caa166d1b6720 ]

If no synflood happens for a long enough period of time, then the
synflood timestamp isn't refreshed and jiffies can advance so much
that time_after32() can't accurately compare them any more.

Therefore, we can end up in a situation where time_after32(now,
last_overflow + HZ) returns false, just because these two values are
too far apart. In that case, the synflood timestamp isn't updated as
it should be, which can trick tcp_synq_no_recent_overflow() into
rejecting valid syncookies.

For example, let's consider the following scenario on a system
with HZ=1000:

  * The synflood timestamp is 0, either because that's the timestamp
    of the last synflood or, more commonly, because we're working with
    a freshly created socket.

  * We receive a new SYN, which triggers synflood protection. Let's say
    that this happens when jiffies == 2147484649 (that is,
    'synflood timestamp' + HZ + 2^31 + 1).

  * Then tcp_synq_overflow() doesn't update the synflood timestamp,
    because time_after32(2147484649, 1000) returns false.
    With:
      - 2147484649: the value of jiffies, aka. 'now'.
      - 1000: the value of 'last_overflow' + HZ.

  * A bit later, we receive the ACK completing the 3WHS. But
    cookie_v[46]_check() rejects it because tcp_synq_no_recent_overflow()
    says that we're not under synflood. That's because
    time_after32(2147484649, 120000) returns false.
    With:
      - 2147484649: the value of jiffies, aka. 'now'.
      - 120000: the value of 'last_overflow' + TCP_SYNCOOKIE_VALID.

    Of course, in reality jiffies would have increased a bit, but this
    condition will last for the next 119 seconds, which is far enough
    to accommodate for jiffie's growth.

Fix this by updating the overflow timestamp whenever jiffies isn't
within the [last_overflow, last_overflow + HZ] range. That shouldn't
have any performance impact since the update still happens at most once
per second.

Now we're guaranteed to have fresh timestamps while under synflood, so
tcp_synq_no_recent_overflow() can safely use it with time_after32() in
such situations.

Stale timestamps can still make tcp_synq_no_recent_overflow() return
the wrong verdict when not under synflood. This will be handled in the
next patch.

For 64 bits architectures, the problem was introduced with the
conversion of ->tw_ts_recent_stamp to 32 bits integer by commit
cca9bab1b72c ("tcp: use monotonic timestamps for PAWS").
The problem has always been there on 32 bits architectures.

Fixes: cca9bab1b72c ("tcp: use monotonic timestamps for PAWS")
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: ipv6_stub: use ip6_dst_lookup_flow instead of ip6_dst_lookup

[ Upstream commit 6c8991f41546c3c472503dff1ea9daaddf9331c2 ]

ipv6_stub uses the ip6_dst_lookup function to allow other modules to
perform IPv6 lookups. However, this function skips the XFRM layer
entirely.

All users of ipv6_stub->ip6_dst_lookup use ip_route_output_flow (via the
ip_route_output_key and ip_route_output helpers) for their IPv4 lookups,
which calls xfrm_lookup_route(). This patch fixes this inconsistent
behavior by switching the stub to ip6_dst_lookup_flow, which also calls
xfrm_lookup_route().

This requires some changes in all the callers, as these two functions
take different arguments and have different return types.

Fixes: 5f81bd2e5d80 ("ipv6: export a stub for IPv6 symbols used by vxlan")
Reported-by: Xiumei Mu <xmu@redhat.com>
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: ipv6: add net argument to ip6_dst_lookup_flow

[ Upstream commit c4e85f73afb6384123e5ef1bba3315b2e3ad031e ]

This will be used in the conversion of ipv6_stub to ip6_dst_lookup_flow,
as some modules currently pass a net argument without a socket to
ip6_dst_lookup. This is equivalent to commit 343d60aada5a ("ipv6: change
ipv6_stub_impl.ipv6_dst_lookup to take net argument").

Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net/mlx5e: Query global pause state before setting prio2buffer

[ Upstream commit 73e6551699a32fac703ceea09214d6580edcf2d5 ]

When the user changes prio2buffer mapping while global pause is
enabled, mlx5 driver incorrectly sets all active buffers
(buffer that has at least one priority mapped) to lossy.

Solution:
If global pause is enabled, set all the active buffers to lossless
in prio2buffer command.
Also, add error message when buffer size is not enough to meet
xoff threshold.

Fixes: 0696d60853d5 ("net/mlx5e: Receive buffer configuration")
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tipc: fix ordering of tipc module init and exit routine

[ Upstream commit 9cf1cd8ee3ee09ef2859017df2058e2f53c5347f ]

In order to set/get/dump, the tipc uses the generic netlink
infrastructure. So, when tipc module is inserted, init function
calls genl_register_family().
After genl_register_family(), set/get/dump commands are immediately
allowed and these callbacks internally use the net_generic.
net_generic is allocated by register_pernet_device() but this
is called after genl_register_family() in the __init function.
So, these callbacks would use un-initialized net_generic.

Test commands:
    #SHELL1
    while :
    do
        modprobe tipc
        modprobe -rv tipc
    done

    #SHELL2
    while :
    do
        tipc link list
    done

Splat looks like:
[   59.616322][ T2788] kasan: CONFIG_KASAN_INLINE enabled
[   59.617234][ T2788] kasan: GPF could be caused by NULL-ptr deref or user memory access
[   59.618398][ T2788] general protection fault: 0000 [#1] SMP DEBUG_PAGEALLOC KASAN PTI
[   59.619389][ T2788] CPU: 3 PID: 2788 Comm: tipc Not tainted 5.4.0+ #194
[   59.620231][ T2788] Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006
[   59.621428][ T2788] RIP: 0010:tipc_bcast_get_broadcast_mode+0x131/0x310 [tipc]
[   59.622379][ T2788] Code: c7 c6 ef 8b 38 c0 65 ff 0d 84 83 c9 3f e8 d7 a5 f2 e3 48 8d bb 38 11 00 00 48 b8 00 00 00 00
[   59.622550][ T2780] NET: Registered protocol family 30
[   59.624627][ T2788] RSP: 0018:ffff88804b09f578 EFLAGS: 00010202
[   59.624630][ T2788] RAX: dffffc0000000000 RBX: 0000000000000011 RCX: 000000008bc66907
[   59.624631][ T2788] RDX: 0000000000000229 RSI: 000000004b3cf4cc RDI: 0000000000001149
[   59.624633][ T2788] RBP: ffff88804b09f588 R08: 0000000000000003 R09: fffffbfff4fb3df1
[   59.624635][ T2788] R10: fffffbfff50318f8 R11: ffff888066cadc18 R12: ffffffffa6cc2f40
[   59.624637][ T2788] R13: 1ffff11009613eba R14: ffff8880662e9328 R15: ffff8880662e9328
[   59.624639][ T2788] FS:  00007f57d8f7b740(0000) GS:ffff88806cc00000(0000) knlGS:0000000000000000
[   59.624645][ T2788] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[   59.625875][ T2780] tipc: Started in single node mode
[   59.626128][ T2788] CR2: 00007f57d887a8c0 CR3: 000000004b140002 CR4: 00000000000606e0
[   59.633991][ T2788] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[   59.635195][ T2788] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[   59.636478][ T2788] Call Trace:
[   59.637025][ T2788]  tipc_nl_add_bc_link+0x179/0x1470 [tipc]
[   59.638219][ T2788]  ? lock_downgrade+0x6e0/0x6e0
[   59.638923][ T2788]  ? __tipc_nl_add_link+0xf90/0xf90 [tipc]
[   59.639533][ T2788]  ? tipc_nl_node_dump_link+0x318/0xa50 [tipc]
[   59.640160][ T2788]  ? mutex_lock_io_nested+0x1380/0x1380
[   59.640746][ T2788]  tipc_nl_node_dump_link+0x4fd/0xa50 [tipc]
[   59.641356][ T2788]  ? tipc_nl_node_reset_link_stats+0x340/0x340 [tipc]
[   59.642088][ T2788]  ? __skb_ext_del+0x270/0x270
[   59.642594][ T2788]  genl_lock_dumpit+0x85/0xb0
[   59.643050][ T2788]  netlink_dump+0x49c/0xed0
[   59.643529][ T2788]  ? __netlink_sendskb+0xc0/0xc0
[   59.644044][ T2788]  ? __netlink_dump_start+0x190/0x800
[   59.644617][ T2788]  ? __mutex_unlock_slowpath+0xd0/0x670
[   59.645177][ T2788]  __netlink_dump_start+0x5a0/0x800
[   59.645692][ T2788]  genl_rcv_msg+0xa75/0xe90
[   59.646144][ T2788]  ? __lock_acquire+0xdfe/0x3de0
[   59.646692][ T2788]  ? genl_family_rcv_msg_attrs_parse+0x320/0x320
[   59.647340][ T2788]  ? genl_lock_dumpit+0xb0/0xb0
[   59.647821][ T2788]  ? genl_unlock+0x20/0x20
[   59.648290][ T2788]  ? genl_parallel_done+0xe0/0xe0
[   59.648787][ T2788]  ? find_held_lock+0x39/0x1d0
[   59.649276][ T2788]  ? genl_rcv+0x15/0x40
[   59.649722][ T2788]  ? lock_contended+0xcd0/0xcd0
[   59.650296][ T2788]  netlink_rcv_skb+0x121/0x350
[   59.650828][ T2788]  ? genl_family_rcv_msg_attrs_parse+0x320/0x320
[   59.651491][ T2788]  ? netlink_ack+0x940/0x940
[   59.651953][ T2788]  ? lock_acquire+0x164/0x3b0
[   59.652449][ T2788]  genl_rcv+0x24/0x40
[   59.652841][ T2788]  netlink_unicast+0x421/0x600
[ ... ]

Fixes: 7e4369057806 ("tipc: fix a slab object leak")
Fixes: a62fbccecd62 ("tipc: make subscriber server support net namespace")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tcp: md5: fix potential overestimation of TCP option space

[ Upstream commit 9424e2e7ad93ffffa88f882c9bc5023570904b55 ]

Back in 2008, Adam Langley fixed the corner case of packets for flows
having all of the following options : MD5 TS SACK

Since MD5 needs 20 bytes, and TS needs 12 bytes, no sack block
can be cooked from the remaining 8 bytes.

tcp_established_options() correctly sets opts->num_sack_blocks
to zero, but returns 36 instead of 32.

This means TCP cooks packets with 4 extra bytes at the end
of options, containing unitialized bytes.

Fixes: 33ad798c924b ("tcp: options clean up")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

openvswitch: support asymmetric conntrack

[ Upstream commit 5d50aa83e2c8e91ced2cca77c198b468ca9210f4 ]

The openvswitch module shares a common conntrack and NAT infrastructure
exposed via netfilter.  It's possible that a packet needs both SNAT and
DNAT manipulation, due to e.g. tuple collision.  Netfilter can support
this because it runs through the NAT table twice - once on ingress and
again after egress.  The openvswitch module doesn't have such capability.

Like netfilter hook infrastructure, we should run through NAT twice to
keep the symmetry.

Fixes: 05752523e565 ("openvswitch: Interface with NAT.")
Signed-off-by: Aaron Conole <aconole@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net/tls: Fix return values to avoid ENOTSUPP

[ Upstream commit 4a5cdc604b9cf645e6fa24d8d9f055955c3c8516 ]

ENOTSUPP is not available in userspace, for example:

  setsockopt failed, 524, Unknown error 524

Signed-off-by: Valentin Vidic <vvidic@valentin-vidic.from.hr>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: thunderx: start phy before starting autonegotiation

[ Upstream commit a350d2e7adbb57181d33e3aa6f0565632747feaa ]

Since commit 2b3e88ea6528 ("net: phy: improve phy state checking")
phy_start_aneg() expects phy state to be >= PHY_UP. Call phy_start()
before calling phy_start_aneg() during probe so that autonegotiation
is initiated.

As phy_start() takes care of calling phy_start_aneg(), drop the explicit
call to phy_start_aneg().

Network fails without this patch on Octeon TX.

Fixes: 2b3e88ea6528 ("net: phy: improve phy state checking")
Signed-off-by: Mian Yousaf Kaukab <ykaukab@suse.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net_sched: validate TCA_KIND attribute in tc_chain_tmplt_add()

[ Upstream commit 2dd5616ecdcebdf5a8d007af64e040d4e9214efe ]

Use the new tcf_proto_check_kind() helper to make sure user
provided value is well formed.

BUG: KMSAN: uninit-value in string_nocheck lib/vsprintf.c:606 [inline]
BUG: KMSAN: uninit-value in string+0x4be/0x600 lib/vsprintf.c:668
CPU: 0 PID: 12358 Comm: syz-executor.1 Not tainted 5.4.0-rc8-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
 __dump_stack lib/dump_stack.c:77 [inline]
 dump_stack+0x1c9/0x220 lib/dump_stack.c:118
 kmsan_report+0x128/0x220 mm/kmsan/kmsan_report.c:108
 __msan_warning+0x64/0xc0 mm/kmsan/kmsan_instr.c:245
 string_nocheck lib/vsprintf.c:606 [inline]
 string+0x4be/0x600 lib/vsprintf.c:668
 vsnprintf+0x218f/0x3210 lib/vsprintf.c:2510
 __request_module+0x2b1/0x11c0 kernel/kmod.c:143
 tcf_proto_lookup_ops+0x171/0x700 net/sched/cls_api.c:139
 tc_chain_tmplt_add net/sched/cls_api.c:2730 [inline]
 tc_ctl_chain+0x1904/0x38a0 net/sched/cls_api.c:2850
 rtnetlink_rcv_msg+0x115a/0x1580 net/core/rtnetlink.c:5224
 netlink_rcv_skb+0x431/0x620 net/netlink/af_netlink.c:2477
 rtnetlink_rcv+0x50/0x60 net/core/rtnetlink.c:5242
 netlink_unicast_kernel net/netlink/af_netlink.c:1302 [inline]
 netlink_unicast+0xf3e/0x1020 net/netlink/af_netlink.c:1328
 netlink_sendmsg+0x110f/0x1330 net/netlink/af_netlink.c:1917
 sock_sendmsg_nosec net/socket.c:637 [inline]
 sock_sendmsg net/socket.c:657 [inline]
 ___sys_sendmsg+0x14ff/0x1590 net/socket.c:2311
 __sys_sendmsg net/socket.c:2356 [inline]
 __do_sys_sendmsg net/socket.c:2365 [inline]
 __se_sys_sendmsg+0x305/0x460 net/socket.c:2363
 __x64_sys_sendmsg+0x4a/0x70 net/socket.c:2363
 do_syscall_64+0xb6/0x160 arch/x86/entry/common.c:291
 entry_SYSCALL_64_after_hwframe+0x44/0xa9
RIP: 0033:0x45a649
Code: ad b6 fb ff c3 66 2e 0f 1f 84 00 00 00 00 00 66 90 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 0f 83 7b b6 fb ff c3 66 2e 0f 1f 84 00 00 00 00
RSP: 002b:00007f0790795c78 EFLAGS: 00000246 ORIG_RAX: 000000000000002e
RAX: ffffffffffffffda RBX: 0000000000000003 RCX: 000000000045a649
RDX: 0000000000000000 RSI: 0000000020000300 RDI: 0000000000000006
RBP: 000000000075bfc8 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 00007f07907966d4
R13: 00000000004c8db5 R14: 00000000004df630 R15: 00000000ffffffff

Uninit was created at:
 kmsan_save_stack_with_flags mm/kmsan/kmsan.c:149 [inline]
 kmsan_internal_poison_shadow+0x5c/0x110 mm/kmsan/kmsan.c:132
 kmsan_slab_alloc+0x97/0x100 mm/kmsan/kmsan_hooks.c:86
 slab_alloc_node mm/slub.c:2773 [inline]
 __kmalloc_node_track_caller+0xe27/0x11a0 mm/slub.c:4381
 __kmalloc_reserve net/core/skbuff.c:141 [inline]
 __alloc_skb+0x306/0xa10 net/core/skbuff.c:209
 alloc_skb include/linux/skbuff.h:1049 [inline]
 netlink_alloc_large_skb net/netlink/af_netlink.c:1174 [inline]
 netlink_sendmsg+0x783/0x1330 net/netlink/af_netlink.c:1892
 sock_sendmsg_nosec net/socket.c:637 [inline]
 sock_sendmsg net/socket.c:657 [inline]
 ___sys_sendmsg+0x14ff/0x1590 net/socket.c:2311
 __sys_sendmsg net/socket.c:2356 [inline]
 __do_sys_sendmsg net/socket.c:2365 [inline]
 __se_sys_sendmsg+0x305/0x460 net/socket.c:2363
 __x64_sys_sendmsg+0x4a/0x70 net/socket.c:2363
 do_syscall_64+0xb6/0x160 arch/x86/entry/common.c:291
 entry_SYSCALL_64_after_hwframe+0x44/0xa9

Fixes: 6f96c3c6904c ("net_sched: fix backward compatibility for TCA_KIND")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Cc: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: sched: fix dump qlen for sch_mq/sch_mqprio with NOLOCK subqueues

[ Upstream commit 2f23cd42e19c22c24ff0e221089b7b6123b117c5 ]

sch->q.len hasn't been set if the subqueue is a NOLOCK qdisc
 in mq_dump() and mqprio_dump().

Fixes: ce679e8df7ed ("net: sched: add support for TCQ_F_NOLOCK subqueues to sch_mqprio")
Signed-off-by: Dust Li <dust.li@linux.alibaba.com>
Signed-off-by: Tony Lu <tonylu@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: ethernet: ti: cpsw: fix extra rx interrupt

[ Upstream commit 51302f77bedab8768b761ed1899c08f89af9e4e2 ]

Now RX interrupt is triggered twice every time, because in
cpsw_rx_interrupt() it is asked first and then disabled. So there will be
pending interrupt always, when RX interrupt is enabled again in NAPI
handler.

Fix it by first disabling IRQ and then do ask.

Fixes: 870915feabdc ("drivers: net: cpsw: remove disable_irq/enable_irq as irq can be masked from cpsw itself")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: dsa: fix flow dissection on Tx path

[ Upstream commit 8bef0af09a5415df761b04fa487a6c34acae74bc ]

Commit 43e665287f93 ("net-next: dsa: fix flow dissection") added an
ability to override protocol and network offset during flow dissection
for DSA-enabled devices (i.e. controllers shipped as switch CPU ports)
in order to fix skb hashing for RPS on Rx path.

However, skb_hash() and added part of code can be invoked not only on
Rx, but also on Tx path if we have a multi-queued device and:
 - kernel is running on UP system or
 - XPS is not configured.

The call stack in this two cases will be like: dev_queue_xmit() ->
__dev_queue_xmit() -> netdev_core_pick_tx() -> netdev_pick_tx() ->
skb_tx_hash() -> skb_get_hash().

The problem is that skbs queued for Tx have both network offset and
correct protocol already set up even after inserting a CPU tag by DSA
tagger, so calling tag_ops->flow_dissect() on this path actually only
breaks flow dissection and hashing.

This can be observed by adding debug prints just before and right after
tag_ops->flow_dissect() call to the related block of code:

Before the patch:

Rx path (RPS):

[   19.240001] Rx: proto: 0x00f8, nhoff: 0 /* ETH_P_XDSA */
[   19.244271] tag_ops->flow_dissect()
[   19.247811] Rx: proto: 0x0800, nhoff: 8 /* ETH_P_IP */

[   19.215435] Rx: proto: 0x00f8, nhoff: 0 /* ETH_P_XDSA */
[   19.219746] tag_ops->flow_dissect()
[   19.223241] Rx: proto: 0x0806, nhoff: 8 /* ETH_P_ARP */

[   18.654057] Rx: proto: 0x00f8, nhoff: 0 /* ETH_P_XDSA */
[   18.658332] tag_ops->flow_dissect()
[   18.661826] Rx: proto: 0x8100, nhoff: 8 /* ETH_P_8021Q */

Tx path (UP system):

[   18.759560] Tx: proto: 0x0800, nhoff: 26 /* ETH_P_IP */
[   18.763933] tag_ops->flow_dissect()
[   18.767485] Tx: proto: 0x920b, nhoff: 34 /* junk */

[   22.800020] Tx: proto: 0x0806, nhoff: 26 /* ETH_P_ARP */
[   22.804392] tag_ops->flow_dissect()
[   22.807921] Tx: proto: 0x920b, nhoff: 34 /* junk */

[   16.898342] Tx: proto: 0x86dd, nhoff: 26 /* ETH_P_IPV6 */
[   16.902705] tag_ops->flow_dissect()
[   16.906227] Tx: proto: 0x920b, nhoff: 34 /* junk */

After:

Rx path (RPS):

[   16.520993] Rx: proto: 0x00f8, nhoff: 0 /* ETH_P_XDSA */
[   16.525260] tag_ops->flow_dissect()
[   16.528808] Rx: proto: 0x0800, nhoff: 8 /* ETH_P_IP */

[   15.484807] Rx: proto: 0x00f8, nhoff: 0 /* ETH_P_XDSA */
[   15.490417] tag_ops->flow_dissect()
[   15.495223] Rx: proto: 0x0806, nhoff: 8 /* ETH_P_ARP */

[   17.134621] Rx: proto: 0x00f8, nhoff: 0 /* ETH_P_XDSA */
[   17.138895] tag_ops->flow_dissect()
[   17.142388] Rx: proto: 0x8100, nhoff: 8 /* ETH_P_8021Q */

Tx path (UP system):

[   15.499558] Tx: proto: 0x0800, nhoff: 26 /* ETH_P_IP */

[   20.664689] Tx: proto: 0x0806, nhoff: 26 /* ETH_P_ARP */

[   18.565782] Tx: proto: 0x86dd, nhoff: 26 /* ETH_P_IPV6 */

In order to fix that we can add the check 'proto == htons(ETH_P_XDSA)'
to prevent code from calling tag_ops->flow_dissect() on Tx.
I also decided to initialize 'offset' variable so tagger callbacks can
now safely leave it untouched without provoking a chaos.

Fixes: 43e665287f93 ("net-next: dsa: fix flow dissection")
Signed-off-by: Alexander Lobakin <alobakin@dlink.ru>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: bridge: deny dev_set_mac_address() when unregistering

[ Upstream commit c4b4c421857dc7b1cf0dccbd738472360ff2cd70 ]

We have an interesting memory leak in the bridge when it is being
unregistered and is a slave to a master device which would change the
mac of its slaves on unregister (e.g. bond, team). This is a very
unusual setup but we do end up leaking 1 fdb entry because
dev_set_mac_address() would cause the bridge to insert the new mac address
into its table after all fdbs are flushed, i.e. after dellink() on the
bridge has finished and we call NETDEV_UNREGISTER the bond/team would
release it and will call dev_set_mac_address() to restore its original
address and that in turn will add an fdb in the bridge.
One fix is to check for the bridge dev's reg_state in its
ndo_set_mac_address callback and return an error if the bridge is not in
NETREG_REGISTERED.

Easy steps to reproduce:
 1. add bond in mode != A/B
 2. add any slave to the bond
 3. add bridge dev as a slave to the bond
 4. destroy the bridge device

Trace:
 unreferenced object 0xffff888035c4d080 (size 128):
   comm "ip", pid 4068, jiffies 4296209429 (age 1413.753s)
   hex dump (first 32 bytes):
     41 1d c9 36 80 88 ff ff 00 00 00 00 00 00 00 00  A..6............
     d2 19 c9 5e 3f d7 00 00 00 00 00 00 00 00 00 00  ...^?...........
   backtrace:
     [<00000000ddb525dc>] kmem_cache_alloc+0x155/0x26f
     [<00000000633ff1e0>] fdb_create+0x21/0x486 [bridge]
     [<0000000092b17e9c>] fdb_insert+0x91/0xdc [bridge]
     [<00000000f2a0f0ff>] br_fdb_change_mac_address+0xb3/0x175 [bridge]
     [<000000001de02dbd>] br_stp_change_bridge_id+0xf/0xff [bridge]
     [<00000000ac0e32b1>] br_set_mac_address+0x76/0x99 [bridge]
     [<000000006846a77f>] dev_set_mac_address+0x63/0x9b
     [<00000000d30738fc>] __bond_release_one+0x3f6/0x455 [bonding]
     [<00000000fc7ec01d>] bond_netdev_event+0x2f2/0x400 [bonding]
     [<00000000305d7795>] notifier_call_chain+0x38/0x56
     [<0000000028885d4a>] call_netdevice_notifiers+0x1e/0x23
     [<000000008279477b>] rollback_registered_many+0x353/0x6a4
     [<0000000018ef753a>] unregister_netdevice_many+0x17/0x6f
     [<00000000ba854b7a>] rtnl_delete_link+0x3c/0x43
     [<00000000adf8618d>] rtnl_dellink+0x1dc/0x20a
     [<000000009b6395fd>] rtnetlink_rcv_msg+0x23d/0x268

Fixes: 43598813386f ("bridge: add local MAC address to forwarding table (v2)")
Reported-by: syzbot+2add91c08eb181fea1bf@syzkaller.appspotmail.com
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mqprio: Fix out-of-bounds access in mqprio_dump

[ Upstream commit 9f104c7736904ac72385bbb48669e0c923ca879b ]

When user runs a command like
tc qdisc add dev eth1 root mqprio
KASAN stack-out-of-bounds warning is emitted.
Currently, NLA_ALIGN macro used in mqprio_dump provides too large
buffer size as argument for nla_put and memcpy down the call stack.
The flow looks like this:
1. nla_put expects exact object size as an argument;
2. Later it provides this size to memcpy;
3. To calculate correct padding for SKB, nla_put applies NLA_ALIGN
   macro itself.

Therefore, NLA_ALIGN should not be applied to the nla_put parameter.
Otherwise it will lead to out-of-bounds memory access in memcpy.

Fixes: 4e8b86c06269 ("mqprio: Introduce new hardware offload mode and shaper in mqprio")
Signed-off-by: Vladyslav Tarasiuk <vladyslavt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

inet: protect against too small mtu values.

[ Upstream commit 501a90c945103e8627406763dac418f20f3837b2 ]

syzbot was once again able to crash a host by setting a very small mtu
on loopback device.

Let's make inetdev_valid_mtu() available in include/net/ip.h,
and use it in ip_setup_cork(), so that we protect both ip_append_page()
and __ip_append_data()

Also add a READ_ONCE() when the device mtu is read.

Pairs this lockless read with one WRITE_ONCE() in __dev_set_mtu(),
even if other code paths might write over this field.

Add a big comment in include/linux/netdevice.h about dev->mtu
needing READ_ONCE()/WRITE_ONCE() annotations.

Hopefully we will add the missing ones in followup patches.

[1]

refcount_t: saturated; leaking memory.
WARNING: CPU: 0 PID: 9464 at lib/refcount.c:22 refcount_warn_saturate+0x138/0x1f0 lib/refcount.c:22
Kernel panic - not syncing: panic_on_warn set ...
CPU: 0 PID: 9464 Comm: syz-executor850 Not tainted 5.4.0-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
 __dump_stack lib/dump_stack.c:77 [inline]
 dump_stack+0x197/0x210 lib/dump_stack.c:118
 panic+0x2e3/0x75c kernel/panic.c:221
 __warn.cold+0x2f/0x3e kernel/panic.c:582
 report_bug+0x289/0x300 lib/bug.c:195
 fixup_bug arch/x86/kernel/traps.c:174 [inline]
 fixup_bug arch/x86/kernel/traps.c:169 [inline]
 do_error_trap+0x11b/0x200 arch/x86/kernel/traps.c:267
 do_invalid_op+0x37/0x50 arch/x86/kernel/traps.c:286
 invalid_op+0x23/0x30 arch/x86/entry/entry_64.S:1027
RIP: 0010:refcount_warn_saturate+0x138/0x1f0 lib/refcount.c:22
Code: 06 31 ff 89 de e8 c8 f5 e6 fd 84 db 0f 85 6f ff ff ff e8 7b f4 e6 fd 48 c7 c7 e0 71 4f 88 c6 05 56 a6 a4 06 01 e8 c7 a8 b7 fd <0f> 0b e9 50 ff ff ff e8 5c f4 e6 fd 0f b6 1d 3d a6 a4 06 31 ff 89
RSP: 0018:ffff88809689f550 EFLAGS: 00010286
RAX: 0000000000000000 RBX: 0000000000000000 RCX: 0000000000000000
RDX: 0000000000000000 RSI: ffffffff815e4336 RDI: ffffed1012d13e9c
RBP: ffff88809689f560 R08: ffff88809c50a3c0 R09: fffffbfff15d31b1
R10: fffffbfff15d31b0 R11: ffffffff8ae98d87 R12: 0000000000000001
R13: 0000000000040100 R14: ffff888099041104 R15: ffff888218d96e40
 refcount_add include/linux/refcount.h:193 [inline]
 skb_set_owner_w+0x2b6/0x410 net/core/sock.c:1999
 sock_wmalloc+0xf1/0x120 net/core/sock.c:2096
 ip_append_page+0x7ef/0x1190 net/ipv4/ip_output.c:1383
 udp_sendpage+0x1c7/0x480 net/ipv4/udp.c:1276
 inet_sendpage+0xdb/0x150 net/ipv4/af_inet.c:821
 kernel_sendpage+0x92/0xf0 net/socket.c:3794
 sock_sendpage+0x8b/0xc0 net/socket.c:936
 pipe_to_sendpage+0x2da/0x3c0 fs/splice.c:458
 splice_from_pipe_feed fs/splice.c:512 [inline]
 __splice_from_pipe+0x3ee/0x7c0 fs/splice.c:636
 splice_from_pipe+0x108/0x170 fs/splice.c:671
 generic_splice_sendpage+0x3c/0x50 fs/splice.c:842
 do_splice_from fs/splice.c:861 [inline]
 direct_splice_actor+0x123/0x190 fs/splice.c:1035
 splice_direct_to_actor+0x3b4/0xa30 fs/splice.c:990
 do_splice_direct+0x1da/0x2a0 fs/splice.c:1078
 do_sendfile+0x597/0xd00 fs/read_write.c:1464
 __do_sys_sendfile64 fs/read_write.c:1525 [inline]
 __se_sys_sendfile64 fs/read_write.c:1511 [inline]
 __x64_sys_sendfile64+0x1dd/0x220 fs/read_write.c:1511
 do_syscall_64+0xfa/0x790 arch/x86/entry/common.c:294
 entry_SYSCALL_64_after_hwframe+0x49/0xbe
RIP: 0033:0x441409
Code: e8 ac e8 ff ff 48 83 c4 18 c3 0f 1f 80 00 00 00 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 0f 83 eb 08 fc ff c3 66 2e 0f 1f 84 00 00 00 00
RSP: 002b:00007fffb64c4f78 EFLAGS: 00000246 ORIG_RAX: 0000000000000028
RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 0000000000441409
RDX: 0000000000000000 RSI: 0000000000000006 RDI: 0000000000000005
RBP: 0000000000073b8a R08: 0000000000000010 R09: 0000000000000010
R10: 0000000000010001 R11: 0000000000000246 R12: 0000000000402180
R13: 0000000000402210 R14: 0000000000000000 R15: 0000000000000000
Kernel Offset: disabled
Rebooting in 86400 seconds..

Fixes: 1470ddf7f8ce ("inet: Remove explicit write references to sk/inet in ip_append_data")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Linux 5.4.4

EDAC/ghes: Do not warn when incrementing refcount on 0

[ Upstream commit 16214bd9e43a31683a7073664b000029bba00354 ]

The following warning from the refcount framework is seen during ghes
initialization:

  EDAC MC0: Giving out device to module ghes_edac.c controller ghes_edac: DEV ghes (INTERRUPT)
  ------------[ cut here ]------------
  refcount_t: increment on 0; use-after-free.
  WARNING: CPU: 36 PID: 1 at lib/refcount.c:156 refcount_inc_checked
 [...]
  Call trace:
   refcount_inc_checked
   ghes_edac_register
   ghes_probe
   ...

It warns if the refcount is incremented from zero. This warning is
reasonable as a kernel object is typically created with a refcount of
one and freed once the refcount is zero. Afterwards the object would be
"used-after-free".

For GHES, the refcount is initialized with zero, and that is why this
message is seen when initializing the first instance. However, whenever
the refcount is zero, the device will be allocated and registered. Since
the ghes_reg_mutex protects the refcount and serializes allocation and
freeing of ghes devices, a use-after-free cannot happen here.

Instead of using refcount_inc() for the first instance, use
refcount_set(). This can be used here because the refcount is zero at
this point and can not change due to its protection by the mutex.

Fixes: 23f61b9fc5cc ("EDAC/ghes: Fix locking and memory barrier issues")
Reported-by: John Garry <john.garry@huawei.com>
Signed-off-by: Robert Richter <rrichter@marvell.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Tested-by: John Garry <john.garry@huawei.com>
Cc: <huangming23@huawei.com>
Cc: James Morse <james.morse@arm.com>
Cc: <linuxarm@huawei.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: <tanxiaofei@huawei.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: <wanghuiqiang@huawei.com>
Link: https://lkml.kernel.org/r/20191121213628.21244-1-rrichter@marvell.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

r8169: fix rtl_hw_jumbo_disable for RTL8168evl

[ Upstream commit 0fc75219fe9a3c90631453e9870e4f6d956f0ebc ]

In referenced fix we removed the RTL8168e-specific jumbo config for
RTL8168evl in rtl_hw_jumbo_enable(). We have to do the same in
rtl_hw_jumbo_disable().

v2: fix referenced commit id

Fixes: 14012c9f3bb9 ("r8169: fix jumbo configuration for RTL8168evl")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

workqueue: Fix missing kfree(rescuer) in destroy_workqueue()

commit 8efe1223d73c218ce7e8b2e0e9aadb974b582d7f upstream.

Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Qian Cai <cai@lca.pw>
Fixes: def98c84b6cd ("workqueue: Fix spurious sanity check failures in destroy_workqueue()")
Cc: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

blk-mq: make sure that line break can be printed

commit d2c9be89f8ebe7ebcc97676ac40f8dec1cf9b43a upstream.

8962842ca5ab ("blk-mq: avoid sysfs buffer overflow with too many CPU cores")
avoids sysfs buffer overflow, and reserves one character for line break.
However, the last snprintf() doesn't get correct 'size' parameter passed
in, so fixed it.

Fixes: 8962842ca5ab ("blk-mq: avoid sysfs buffer overflow with too many CPU cores")
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Cc: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ext4: fix leak of quota reservations

commit f4c2d372b89a1e504ebb7b7eb3e29b8306479366 upstream.

Commit 8fcc3a580651 ("ext4: rework reserved cluster accounting when
invalidating pages") moved freeing of delayed allocation reservations
from dirty page invalidation time to time when we evict corresponding
status extent from extent status tree. For inodes which don't have any
blocks allocated this may actually happen only in ext4_clear_blocks()
which is after we've dropped references to quota structures from the
inode. Thus reservation of quota leaked. Fix the problem by clearing
quota information from the inode only after evicting extent status tree
in ext4_clear_inode().

Link: https://lore.kernel.org/r/20191108115420.GI20863@quack2.suse.cz
Reported-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Fixes: 8fcc3a580651 ("ext4: rework reserved cluster accounting when invalidating pages")
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ext4: fix a bug in ext4_wait_for_tail_page_commit

commit 565333a1554d704789e74205989305c811fd9c7a upstream.

No need to wait for any commit once the page is fully truncated.
Besides, it may confuse e.g. concurrent ext4_writepage() with the page
still be dirty (will be cleared by truncate_pagecache() in
ext4_setattr()) but buffers has been freed; and then trigger a bug
show as below:

[   26.057508] ------------[ cut here ]------------
[   26.058531] kernel BUG at fs/ext4/inode.c:2134!
...
[   26.088130] Call trace:
[   26.088695]  ext4_writepage+0x914/0xb28
[   26.089541]  writeout.isra.4+0x1b4/0x2b8
[   26.090409]  move_to_new_page+0x3b0/0x568
[   26.091338]  __unmap_and_move+0x648/0x988
[   26.092241]  unmap_and_move+0x48c/0xbb8
[   26.093096]  migrate_pages+0x220/0xb28
[   26.093945]  kernel_mbind+0x828/0xa18
[   26.094791]  __arm64_sys_mbind+0xc8/0x138
[   26.095716]  el0_svc_common+0x190/0x490
[   26.096571]  el0_svc_handler+0x60/0xd0
[   26.097423]  el0_svc+0x8/0xc

Run the procedure (generate by syzkaller) parallel with ext3.

void main()
{
int fd, fd1, ret;
void *addr;
size_t length = 4096;
int flags;
off_t offset = 0;
char *str = "12345";

fd = open("a", O_RDWR | O_CREAT);
assert(fd >= 0);

/* Truncate to 4k */
ret = ftruncate(fd, length);
assert(ret == 0);

/* Journal data mode */
flags = 0xc00f;
ret = ioctl(fd, _IOW('f', 2, long), &flags);
assert(ret == 0);

/* Truncate to 0 */
fd1 = open("a", O_TRUNC | O_NOATIME);
assert(fd1 >= 0);

addr = mmap(NULL, length, PROT_WRITE | PROT_READ,
MAP_SHARED, fd, offset);
assert(addr != (void *)-1);

memcpy(addr, str, 5);
mbind(addr, length, 0, 0, 0, MPOL_MF_MOVE);
}

And the bug will be triggered once we seen the below order.

reproduce1                         reproduce2

...                            |   ...
truncate to 4k                 |
change to journal data mode    |
                               |   memcpy(set page dirty)
truncate to 0:                 |
ext4_setattr:                  |
...                            |
ext4_wait_for_tail_page_commit |
                               |   mbind(trigger bug)
truncate_pagecache(clean dirty)|   ...
...                            |

mbind will call ext4_writepage() since the page still be dirty, and then
report the bug since the buffers has been free. Fix it by return
directly once offset equals to 0 which means the page has been fully
truncated.

Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: yangerkun <yangerkun@huawei.com>
Link: https://lore.kernel.org/r/20190919063508.1045-1-yangerkun@huawei.com
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

splice: only read in as much information as there is pipe buffer space

commit 3253d9d093376d62b4a56e609f15d2ec5085ac73 upstream.

Andreas Grünbacher reports that on the two filesystems that support
iomap directio, it's possible for splice() to return -EAGAIN (instead of
a short splice) if the pipe being written to has less space available in
its pipe buffers than the length supplied by the calling process.

Months ago we fixed splice_direct_to_actor to clamp the length of the
read request to the size of the splice pipe.  Do the same to do_splice.

Fixes: 17614445576b6 ("splice: don't read more than available pipe space")
Reported-by: syzbot+3c01db6025f26530cf8d@syzkaller.appspotmail.com
Reported-by: Andreas Grünbacher <andreas.gruenbacher@gmail.com>
Reviewed-by: Andreas Grünbacher <andreas.gruenbacher@gmail.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

rtc: disable uie before setting time and enable after

commit 7e7c005b4b1f1f169bcc4b2c3a40085ecc663df2 upstream.

When setting the time in the future with the uie timer enabled,
rtc_timer_do_work will loop for a while because the expiration of the uie
timer was way before the current RTC time and a new timer will be enqueued
until the current rtc time is reached.

If the uie timer is enabled, disable it before setting the time and enable
it after expiring current timers (which may actually be an alarm).

This is the safest thing to do to ensure the uie timer is still
synchronized with the RTC, especially in the UIE emulation case.

Reported-by: syzbot+08116743f8ad6f9a6de7@syzkaller.appspotmail.com
Fixes: 6610e0893b8b ("RTC: Rework RTC code to use timerqueue for events")
Link: https://lore.kernel.org/r/20191020231320.8191-1-alexandre.belloni@bootlin.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: dummy-hcd: increase max number of devices to 32

commit 8442b02bf3c6770e0d7e7ea17be36c30e95987b6 upstream.

When fuzzing the USB subsystem with syzkaller, we currently use 8 testing
processes within one VM. To isolate testing processes from one another it
is desirable to assign a dedicated USB bus to each of those, which means
we need at least 8 Dummy UDC/HCD devices.

This patch increases the maximum number of Dummy UDC/HCD devices to 32
(more than 8 in case we need more of them in the future).

Signed-off-by: Andrey Konovalov <andreyknvl@google.com>
Link: https://lore.kernel.org/r/665578f904484069bb6100fb20283b22a046ad9b.1571667489.git.andreyknvl@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

powerpc: Define arch_is_kernel_initmem_freed() for lockdep

commit 6f07048c00fd100ed8cab66c225c157e0b6c0a50 upstream.

Under certain circumstances, we hit a warning in lockdep_register_key:

        if (WARN_ON_ONCE(static_obj(key)))
                return;

This occurs when the key falls into initmem that has since been freed
and can now be reused. This has been observed on boot, and under
memory pressure.

Define arch_is_kernel_initmem_freed(), which allows lockdep to
correctly identify this memory as dynamic.

This fixes a bug picked up by the powerpc64 syzkaller instance where
we hit the WARN via alloc_netdev_mqs.

Reported-by: Qian Cai <cai@lca.pw>
Reported-by: ppc syzbot c/o Andrew Donnellan <ajd@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Daniel Axtens <dja@axtens.net>
Link: https://lore.kernel.org/r/87lfs4f7d6.fsf@dja-thinkpad.axtens.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>