Aneesh Kumar K.V [Sun, 28 Apr 2013 09:37:38 +0000 (09:37 +0000)]
powerpc: Print page size info during boot
This gives hint about different base and actual page size combination
supported by the platform.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Aneesh Kumar K.V [Sun, 28 Apr 2013 09:37:37 +0000 (09:37 +0000)]
powerpc: print both base and actual page size on hash failure
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Aneesh Kumar K.V [Sun, 28 Apr 2013 09:37:36 +0000 (09:37 +0000)]
powerpc: Fix hpte_decode to use the correct decoding for page sizes
As per ISA doc, we encode base and actual page size in the LP bits of
PTE. The number of bit used to encode the page sizes depend on actual
page size. ISA doc lists this as
PTE LP actual page size
rrrr rrrz >=8KB
rrrr rrzz >=16KB
rrrr rzzz >=32KB
rrrr zzzz >=64KB
rrrz zzzz >=128KB
rrzz zzzz >=256KB
rzzz zzzz >=512KB
zzzz zzzz >=1MB
ISA doc also says
"The values of the “z” bits used to specify each size, along with all possible
values of “r” bits in the LP field, must result in LP values distinct from
other LP values for other sizes."
based on the above update hpte_decode to use the correct decoding for LP bits.
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Aneesh Kumar K.V [Sun, 28 Apr 2013 09:37:35 +0000 (09:37 +0000)]
powerpc: Decode the pte-lp-encoding bits correctly.
We look at both the segment base page size and actual page size and store
the pte-lp-encodings in an array per base page size.
We also update all relevant functions to take actual page size argument
so that we can use the correct PTE LP encoding in HPTE. This should also
get the basic Multiple Page Size per Segment (MPSS) support. This is needed
to enable THP on ppc64.
[Fixed PR KVM build --BenH]
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Aneesh Kumar K.V [Sun, 28 Apr 2013 09:37:34 +0000 (09:37 +0000)]
powerpc: Use encode avpn where we need only avpn values
In all these cases we are doing something similar to
HPTE_V_COMPARE(hpte_v, want_v) which ignores the HPTE_V_LARGE bit
With MPSS support we would need actual page size to set HPTE_V_LARGE
bit and that won't be available in most of these cases. Since we are ignoring
HPTE_V_LARGE bit, use the avpn value instead. There should not be any change
in behaviour after this patch.
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Aneesh Kumar K.V [Sun, 28 Apr 2013 09:37:33 +0000 (09:37 +0000)]
powerpc: Reduce PTE table memory wastage
We allocate one page for the last level of linux page table. With THP and
large page size of 16MB, that would mean we are wasting large part
of that page. To map 16MB area, we only need a PTE space of 2K with 64K
page size. This patch reduce the space wastage by sharing the page
allocated for the last level of linux page table with multiple pmd
entries. We call these smaller chunks PTE page fragments and allocated
page, PTE page.
In order to support systems which doesn't have 64K HPTE support, we also
add another 2K to PTE page fragment. The second half of the PTE fragments
is used for storing slot and secondary bit information of an HPTE. With this
we now have a 4K PTE fragment.
We use a simple approach to share the PTE page. On allocation, we bump the
PTE page refcount to 16 and share the PTE page with the next 16 pte alloc
request. This should help in the node locality of the PTE page fragment,
assuming that the immediate pte alloc request will mostly come from the
same NUMA node. We don't try to reuse the freed PTE page fragment. Hence
we could be waisting some space.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Aneesh Kumar K.V [Sun, 28 Apr 2013 09:37:32 +0000 (09:37 +0000)]
powerpc: Move the pte free routines from common header
Acked-by: Paul Mackerras <paulus@samba.org>
This patch moves the common code to 32/64 bit headers and also duplicate
4K_PAGES and 64K_PAGES section. We will later change the 64 bit 64K_PAGES
version to support smaller PTE fragments. The patch doesn't introduce
any functional changes.
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Aneesh Kumar K.V [Sun, 28 Apr 2013 09:37:31 +0000 (09:37 +0000)]
powerpc: Reduce the PTE_INDEX_SIZE
This make one PMD cover 16MB range. That helps in easier implementation of THP
on power. THP core code make use of one pmd entry to track the hugepage and
the range mapped by a single pmd entry should be equal to the hugepage size
supported by the hardware.
This also switch PGD to cover 16GB. That is needed so that we can simplify the
hugetlb page walking code so that we have same pte format for explicit hugepage
and THP hugepage.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Aneesh Kumar K.V [Sun, 28 Apr 2013 09:37:30 +0000 (09:37 +0000)]
powerpc: Switch 16GB and 16MB explicit hugepages to a different page table format
We will be switching PMD_SHIFT to 24 bits to facilitate THP impmenetation.
With PMD_SHIFT set to 24, we now have 16MB huge pages allocated at PGD level.
That means with 32 bit process we cannot allocate normal pages at
all, because we cover the entire address space with one pgd entry. Fix this
by switching to a new page table format for hugepages. With the new page table
format for 16GB and 16MB hugepages we won't allocate hugepage directory. Instead
we encode the PTE information directly at the directory level. This forces 16MB
hugepage at PMD level. This will also make the page take walk much simpler later
when we add the THP support.
With the new table format we have 4 cases for pgds and pmds:
(1) invalid (all zeroes)
(2) pointer to next table, as normal; bottom 6 bits == 0
(3) leaf pte for huge page, bottom two bits != 00
(4) hugepd pointer, bottom two bits == 00, next 4 bits indicate size of table
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Aneesh Kumar K.V [Sun, 28 Apr 2013 09:37:29 +0000 (09:37 +0000)]
powerpc: New hugepage directory format
Change the hugepage directory format so that we can have leaf ptes directly
at page directory avoiding the allocation of hugepage directory.
With the new table format we have 3 cases for pgds and pmds:
(1) invalid (all zeroes)
(2) pointer to next table, as normal; bottom 6 bits == 0
(4) hugepd pointer, bottom two bits == 00, next 4 bits indicate size of table
Instead of storing shift value in hugepd pointer we use mmu_psize_def index
so that we can fit all the supported hugepage size in 4 bits
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Aneesh Kumar K.V [Sun, 28 Apr 2013 09:37:28 +0000 (09:37 +0000)]
powerpc: Don't truncate pgd_index wrongly
With PGD_INDEX_SIZE set to 12 the existing macro doesn't work. Fix it to
use PTRS_PER_PGD
The idea originally was to have one more bit in the result of
pgd_index() than PGD_INDEX_SIZE, so that if one had an address
corresponding to the last PGD entry, and then incremented that address
by PGD_SIZE, and took pgd_index() of that, you wouldn't end up with
zero. The commit that introduced that dates back to 2002, and the
code that was sensitive to that edge case has long since been
refactored (several times), so there is no need for it these days.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Aneesh Kumar K.V [Sun, 28 Apr 2013 09:37:27 +0000 (09:37 +0000)]
powerpc: Don't hard code the size of pte page
USE PTRS_PER_PTE to indicate the size of pte page. To support THP,
later patches will be changing PTRS_PER_PTE value.
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Aneesh Kumar K.V [Sun, 28 Apr 2013 09:37:26 +0000 (09:37 +0000)]
powerpc: Save DAR and DSISR in pt_regs on MCE
We were not saving DAR and DSISR on MCE. Save then and also print the values
along with exception details in xmon.
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Aneesh Kumar K.V [Sun, 28 Apr 2013 09:37:25 +0000 (09:37 +0000)]
powerpc: Use signed formatting when printing error
PAPR defines these errors as negative values. So print them accordingly
for easy debugging.
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Nathan Fontenot [Mon, 29 Apr 2013 03:45:36 +0000 (03:45 +0000)]
powerpc/pseries: Correct builds break when CONFIG_SMP not defined
Correct build failure for powerpc/pseries builds with CONFIG_SMP not defined.
The function cpu_sibling_mask has no meaning (or definition) when CONFIG_SMP
is not defined. Additionally, the updating of NUMA affinity for a CPU in a UP
system doesn't really make sense.
This patch ifdef's out the code making the affinity updates for PRRN events to
fix the following build break.
arch/powerpc/mm/numa.c: In function ‘stage_topology_update’:
arch/powerpc/mm/numa.c:1535: error: implicit declaration of function ‘cpu_sibling_mask’
arch/powerpc/mm/numa.c:1535: warning: passing argument 3 of ‘cpumask_or’ makes pointer from integer without a cast
make[1]: *** [arch/powerpc/mm/numa.o] Error 1
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Kevin Hao [Mon, 29 Apr 2013 00:59:57 +0000 (00:59 +0000)]
powerpc/booke: Remove obsolete macro FINISH_EXCEPTION
This is stale and not used by anyone now.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Vasant Hegde [Sun, 28 Apr 2013 18:43:56 +0000 (18:43 +0000)]
powerpc/rtas_flash: Fix bad memory access
We use kmem_cache_alloc() to allocate memory to hold the new firmware
which will be flashed. kmem_cache_alloc() calls rtas_block_ctor() to
set memory to NULL. But these constructor is called only for newly
allocated slabs.
If we run below command multiple time without rebooting, allocator may
allocate memory from the area which was free'd by kmem_cache_free and
it will not call constructor. In this situation we may hit kernel oops.
dd if=<fw image> of=/proc/ppc64/rtas/firmware_flash bs=4096
oops message:
-------------
[ 1602.399755] Oops: Kernel access of bad area, sig: 11 [#1]
[ 1602.399772] SMP NR_CPUS=1024 NUMA pSeries
[ 1602.399779] Modules linked in: rtas_flash nfsd lockd auth_rpcgss nfs_acl sunrpc fuse loop dm_mod sg ipv6 ses enclosure ehea ehci_pci ohci_hcd ehci_hcd usbcore sd_mod usb_common crc_t10dif scsi_dh_alua scsi_dh_emc scsi_dh_hp_sw scsi_dh_rdac scsi_dh ipr libata scsi_mod
[ 1602.399817] NIP:
d00000000a170b9c LR:
d00000000a170b64 CTR:
c00000000079cd58
[ 1602.399823] REGS:
c0000003b9937930 TRAP: 0300 Not tainted (3.9.0-rc4-0.27-ppc64)
[ 1602.399828] MSR:
8000000000009032 <SF,EE,ME,IR,DR,RI> CR:
22000428 XER:
20000000
[ 1602.399841] SOFTE: 1
[ 1602.399844] CFAR:
c000000000005f24
[ 1602.399848] DAR:
8c2625a820631fef, DSISR:
40000000
[ 1602.399852] TASK =
c0000003b4520760[3655] 'dd' THREAD:
c0000003b9934000 CPU: 3
GPR00:
8c2625a820631fe7 c0000003b9937bb0 d00000000a179f28 d00000000a171f08
GPR04:
0000000010040000 0000000000001000 c0000003b9937df0 c0000003b5fb2080
GPR08:
c0000003b58f7200 d00000000a179f28 c0000003b40058d4 c00000000079cd58
GPR12:
d00000000a171450 c000000007f40900 0000000000000005 0000000010178d20
GPR16:
00000000100cb9d8 000000000000001d 0000000000000000 000000001003ffff
GPR20:
0000000000000001 0000000000000000 00003fffa0b50d30 000000001001f010
GPR24:
0000000010020888 0000000010040000 d00000000a171f08 d00000000a172808
GPR28:
0000000000001000 0000000010040000 c0000003b4005880 8c2625a820631fe7
[ 1602.399924] NIP [
d00000000a170b9c] .rtas_flash_write+0x7c/0x1e8 [rtas_flash]
[ 1602.399930] LR [
d00000000a170b64] .rtas_flash_write+0x44/0x1e8 [rtas_flash]
[ 1602.399934] Call Trace:
[ 1602.399939] [
c0000003b9937bb0] [
d00000000a170b64] .rtas_flash_write+0x44/0x1e8 [rtas_flash] (unreliable)
[ 1602.399948] [
c0000003b9937c60] [
c000000000282830] .proc_reg_write+0x90/0xe0
[ 1602.399955] [
c0000003b9937ce0] [
c0000000001ff374] .vfs_write+0x114/0x238
[ 1602.399961] [
c0000003b9937d80] [
c0000000001ff5d8] .SyS_write+0x70/0xe8
[ 1602.399968] [
c0000003b9937e30] [
c000000000009cdc] syscall_exit+0x0/0xa0
[ 1602.399973] Instruction dump:
[ 1602.399977]
eb698010 801b0028 2f80dcd6 419e00a4 2fbc0000 419e009c ebfb0030 2fbf0000
[ 1602.399989]
409e0010 480000d8 60000000 7c1f0378 <
e81f0008>
2fa00000 409efff4 e81f0000
[ 1602.400012] ---[ end trace
b4136d115dc31dac ]---
[ 1602.402178]
[ 1602.402185] Sending IPI to other CPUs
[ 1602.403329] IPI complete
This patch uses kmem_cache_zalloc() instead of kmem_cache_alloc() to
allocate memory, which makes sure memory is set to 0 before using.
Also removes rtas_block_ctor(), which is no longer required.
Signed-off-by: Vasant Hegde <hegdevasant@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Stephen Rothwell [Sun, 28 Apr 2013 18:04:33 +0000 (18:04 +0000)]
powerpc: Fix build failure after merge of the cgroup tree
After merging the cgroup tree, today's linux-next build (powerpc
ppc64_defconfig) failed like this:
arch/powerpc/mm/numa.c: In function 'arch_update_cpu_topology':
arch/powerpc/mm/numa.c:1465:2: error: implicit declaration of function 'kzalloc' [-Werror=implicit-function-declaration]
arch/powerpc/mm/numa.c:1465:10: error: assignment makes pointer from integer without a cast [-Werror]
arch/powerpc/mm/numa.c:1497:2: error: implicit declaration of function 'kfree' [-Werror=implicit-function-declaration]
Caused by commit
30c05350c39d ("powerpc/pseries: Use stop machine to
update cpu maps") from the powerpc tree interacting with (probably)
commit
ff794dea52ea ("cpuset: remove include of cgroup.h from cpuset.h")
from the cgroup tree. Removing includes from header files is fraught
with danger ...
The former should have added an include of linux/slab.h to
arch/powerpc/mm/numa.c.
I have added the following merge fix patch for today (but it should be
applied to the powerpc tree ASAP).
From: Stephen Rothwell <sfr@canb.auug.org.au>
Date: Mon, 29 Apr 2013 14:01:44 +1000
Subject: [PATCH] powerpc: numa.c: using kzalloc/kfree requires including
slab.h
fixes these build errors:
arch/powerpc/mm/numa.c: In function 'arch_update_cpu_topology':
arch/powerpc/mm/numa.c:1465:2: error: implicit declaration of function 'kzalloc' [-Werror=implicit-function-declaration]
arch/powerpc/mm/numa.c:1465:10: error: assignment makes pointer from integer without a cast [-Werror]
arch/powerpc/mm/numa.c:1497:2: error: implicit declaration of function 'kfree' [-Werror=implicit-function-declaration]
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Michael Neuling [Sun, 14 Apr 2013 19:42:01 +0000 (19:42 +0000)]
powerpc: Fix usage of setup_pci_atmu()
Linux next is currently failing to compile mpc85xx_defconfig with:
arch/powerpc/sysdev/fsl_pci.c:944:2: error: too many arguments to function 'setup_pci_atmu'
This is caused by (from Kumar's next branch):
commit
34642bbb3d12121333efcf4ea7dfe66685e403a1
Author: Kumar Gala <galak@kernel.crashing.org>
powerpc/fsl-pci: Keep PCI SoC controller registers in pci_controller
Which changed definition of setup_pci_atmu() but didn't update one of
the callers. Below fixes this.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Reviewed-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Benjamin Herrenschmidt [Tue, 30 Apr 2013 01:10:09 +0000 (11:10 +1000)]
Merge remote-tracking branch 'kumar/next' into next
From Kumar Gala:
<<
Add support for T4 and B4 SoC families from Freescale, e6500 altivec
support, some various board fixes and other minor cleanups.
>>
Benjamin Herrenschmidt [Tue, 30 Apr 2013 01:08:45 +0000 (11:08 +1000)]
Merge remote-tracking branch 'agust/next' into next
From Anatolij Gustschin:
<<
There are some changes for mpc5121 generic platform code
to support mpc5125 SoC and DTS files for ac14xx and
MPC5125-TWR boards.
>>
Michel Lespinasse [Mon, 29 Apr 2013 18:53:53 +0000 (11:53 -0700)]
mm: use vm_unmapped_area() on powerpc architecture
Update the powerpc slice_get_unmapped_area function to make use of
vm_unmapped_area() instead of implementing a brute force search.
Signed-off-by: Michel Lespinasse <walken@google.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Tested-by: "Aneesh Kumar K.V" <aneesh.kumar@linux.vnet.ibm.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Michel Lespinasse [Mon, 29 Apr 2013 18:53:52 +0000 (11:53 -0700)]
mm: remove free_area_cache use in powerpc architecture
As all other architectures have been converted to use vm_unmapped_area(),
we are about to retire the free_area_cache.
This change simply removes the use of that cache in
slice_get_unmapped_area(), which will most certainly have a
performance cost. Next one will convert that function to use the
vm_unmapped_area() infrastructure and regain the performance.
Signed-off-by: Michel Lespinasse <walken@google.com>
Acked-by: Rik van Riel <riel@redhat.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: "Aneesh Kumar K.V" <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Kevin Hao [Sun, 14 Apr 2013 05:40:13 +0000 (13:40 +0800)]
powerpc/fsl-booke: add the reg prop for pci bridge device node for T4/B4
The reg property in the pci bridge device node is used to bind this
device node to the pci bridge device. Then all the pci devices under
this bridge could use the interrupt maps defined in this device node
to do the irq translation. So if this property is missed, the pci
traditional irq mechanism will not work.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kevin Hao [Sat, 13 Apr 2013 07:14:41 +0000 (15:14 +0800)]
powerpc/fsl-pci: don't unmap the PCI SoC controller registers in setup_pci_atmu
In patch
34642bbb (powerpc/fsl-pci: Keep PCI SoC controller registers in
pci_controller) we choose to keep the map of the PCI SoC controller
registers. But we missed to delete the unmap in setup_pci_atmu
function. This will cause the following call trace once we access
the PCI SoC controller registers later.
Unable to handle kernel paging request for data at address 0x8000080080040f14
Faulting instruction address: 0xc00000000002ea58
Oops: Kernel access of bad area, sig: 11 [#1]
SMP NR_CPUS=24 T4240 QDS
Modules linked in:
NIP:
c00000000002ea58 LR:
c00000000002eaf4 CTR:
c00000000002eac0
REGS:
c00000017e10b4a0 TRAP: 0300 Not tainted (3.9.0-rc1-00052-gfa3529f-dirty)
MSR:
0000000080029000 <CE,EE,ME> CR:
28adbe22 XER:
00000000
SOFTE: 0
DEAR:
8000080080040f14, ESR:
0000000000000000
TASK =
c00000017e100000[1] 'swapper/0' THREAD:
c00000017e108000 CPU: 2
GPR00:
0000000000000000 c00000017e10b720 c0000000009928d8 c00000017e578e00
GPR04:
0000000000000000 000000000000000c 0000000000000001 c00000017e10bb40
GPR08:
0000000000000000 8000080080040000 0000000000000000 0000000000000016
GPR12:
0000000088adbe22 c00000000fffa800 c000000000001ba0 0000000000000000
GPR16:
0000000000000000 0000000000000000 0000000000000000 0000000000000000
GPR20:
0000000000000000 0000000000000000 0000000000000000 c0000000008a5b70
GPR24:
c0000000008af938 c0000000009a28d8 c0000000009bb5dc c00000017e10bb40
GPR28:
c00000017e32a400 c00000017e10bc00 c00000017e32a400 c00000017e578e00
NIP [
c00000000002ea58] .fsl_pcie_check_link+0x88/0xf0
LR [
c00000000002eaf4] .fsl_indirect_read_config+0x34/0xb0
Call Trace:
[
c00000017e10b720] [
c00000017e10b7a0] 0xc00000017e10b7a0 (unreliable)
[
c00000017e10ba30] [
c00000000002eaf4] .fsl_indirect_read_config+0x34/0xb0
[
c00000017e10bad0] [
c00000000033aa08] .pci_bus_read_config_byte+0x88/0xd0
[
c00000017e10bb90] [
c00000000088d708] .pci_apply_final_quirks+0x9c/0x18c
[
c00000017e10bc40] [
c0000000000013dc] .do_one_initcall+0x5c/0x1f0
[
c00000017e10bcf0] [
c00000000086ebac] .kernel_init_freeable+0x180/0x26c
[
c00000017e10bdb0] [
c000000000001bbc] .kernel_init+0x1c/0x460
[
c00000017e10be30] [
c000000000000880] .ret_from_kernel_thread+0x64/0xe4
Instruction dump:
38210310 2b800015 4fdde842 7c600026 5463fffe e8010010 7c0803a6 4e800020
60000000 60000000 e92301d0 7c0004ac <
80690f14>
0c030000 4c00012c 38210310
---[ end trace
7a8fe0cbccb7d992 ]---
Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000000b
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Acked-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Zhicheng Fan [Mon, 25 Mar 2013 01:23:06 +0000 (09:23 +0800)]
powerpc/dts: Fix the dts for p1025rdb 36bit
Fix the following errors:
Error: p1025rdb.dtsi:326.2-3 label or path, 'qe', not found
Error: p1021si-post.dtsi:242.2-3 label or path, 'qe', not found
FATAL ERROR: Syntax error parsing input tree
Signed-off-by: Zhicheng Fan <B32736@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Anshuman Khandual [Mon, 22 Apr 2013 19:42:44 +0000 (19:42 +0000)]
powerpc/perf: Enable branch stack sampling framework
Provides basic enablement for perf branch stack sampling framework on
POWER8 processor based platforms. Adds new BHRB related elements into
cpu_hw_event structure to represent current BHRB config, BHRB filter
configuration, manage context and to hold output BHRB buffer during
PMU interrupt before passing to the user space. This also enables
processing of BHRB data and converts them into generic perf branch
stack data format.
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Anshuman Khandual [Mon, 22 Apr 2013 19:42:43 +0000 (19:42 +0000)]
powerpc/perf: Define BHRB generic functions, data and flags for POWER8
This patch populates BHRB specific data for power_pmu structure. It
also implements POWER8 specific BHRB filter and configuration functions.
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Anshuman Khandual [Mon, 22 Apr 2013 19:42:42 +0000 (19:42 +0000)]
powerpc/perf: Add new BHRB related generic functions, data and flags
This patch adds couple of generic functions to power_pmu structure
which would configure the BHRB and it's filters. It also adds
representation of the number of BHRB entries present on the PMU.
A new PMU flag PPMU_BHRB would indicate presence of BHRB feature.
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Anshuman Khandual [Mon, 22 Apr 2013 19:42:41 +0000 (19:42 +0000)]
powerpc/perf: Add basic assembly code to read BHRB entries on POWER8
This patch adds the basic assembly code to read BHRB buffer. BHRB entries
are valid only after a PMU interrupt has happened (when MMCR0[PMAO]=1)
and BHRB has been freezed. BHRB read should not be attempted when it is
still enabled (MMCR0[PMAE]=1) and getting updated, as this can produce
non-deterministic results.
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Anshuman Khandual [Mon, 22 Apr 2013 19:42:40 +0000 (19:42 +0000)]
powerpc/perf: Add new BHRB related instructions for POWER8
This patch adds new POWER8 instruction encoding for reading
and clearing Branch History Rolling Buffer entries. The new
instruction 'mfbhrbe' (move from branch history rolling buffer
entry) is used to read BHRB buffer entries and instruction
'clrbhrb' (clear branch history rolling buffer) is used to
clear the entire buffer. The instruction 'clrbhrb' has straight
forward encoding. But the instruction encoding format for
reading the BHRB entries is like 'mfbhrbe RT, BHRBE' where it
takes two arguments, i.e the index for the BHRB buffer entry to
read and a general purpose register to put the value which was
read from the buffer entry.
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Michael Ellerman [Thu, 25 Apr 2013 19:28:28 +0000 (19:28 +0000)]
powerpc/perf: Power8 PMU support
This patch adds support for the power8 PMU to perf.
Work is ongoing to add generic cache events.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Michael Ellerman [Thu, 25 Apr 2013 19:28:27 +0000 (19:28 +0000)]
powerpc/perf: Add support for SIER
On power8 we have a new SIER (Sampled Instruction Event Register), which
captures information about instructions when we have random sampling
enabled.
Add support for loading the SIER into pt_regs, overloading regs->dar.
Also set the new NO_SIPR flag in regs->result if we don't have SIPR.
Update regs_sihv/sipr() to look for SIPR/SIHV in SIER.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Michael Ellerman [Thu, 25 Apr 2013 19:28:26 +0000 (19:28 +0000)]
powerpc/perf: Add regs_no_sipr()
On power8 the presence or absence of SIPR depends on settings at runtime,
so convert to using a dynamic flag for NO_SIPR. Existing backends that
set NO_SIPR unconditionally set the dynamic flag obviously.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Michael Ellerman [Thu, 25 Apr 2013 19:28:25 +0000 (19:28 +0000)]
powerpc/perf: Add an accessor for regs->result
Add an accessor for regs->result so we can use it to store more flags in
future.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Michael Ellerman [Thu, 25 Apr 2013 19:28:24 +0000 (19:28 +0000)]
powerpc/perf: Convert mmcra_sipr/sihv() to regs_sipr/sihv()
On power8 the SIPR and SIHV are not in MMCRA, so convert the routines
to take regs and change the names accordingly.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Michael Ellerman [Thu, 25 Apr 2013 19:28:23 +0000 (19:28 +0000)]
powerpc/perf: Add an explict flag indicating presence of SLOT field
In perf_ip_adjust() we potentially use the MMCRA[SLOT] field to adjust
the reported IP of a sampled instruction.
Currently the logic is written so that if the backend does NOT have
the PPMU_ALT_SIPR flag set then we assume MMCRA[SLOT] exists.
However on power8 we do not want to set ALT_SIPR (it's in a third
location), and we also do not have MMCRA[SLOT].
So add a new flag which only indicates whether MMCRA[SLOT] exists.
Naively we'd set it on everything except power6/7, because they set
ALT_SIPR, and we've reversed the polarity of the flag. But it's more
complicated than that.
mpc7450 is 32-bit, and uses its own version of perf_ip_adjust()
which doesn't use MMCRA[SLOT], so it doesn't need the new flag set and
the behaviour is unchanged.
PPC970 (and I assume power4) don't have MMCRA[SLOT], so shouldn't have
the new flag set. This is a behaviour change on those cpus, though we
were probably getting lucky and the bits in question were 0.
power5 and power5+ set the new flag, behaviour unchanged.
power6 & power7 do not set the new flag, behaviour unchanged.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Michael Ellerman [Thu, 25 Apr 2013 19:28:22 +0000 (19:28 +0000)]
powerpc: Initialise PMU related regs on Power8
For both HV and guest kernels, intialise PMU regs to something sane.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Gavin Shan [Thu, 25 Apr 2013 19:21:02 +0000 (19:21 +0000)]
powerpc/powernv: Fix invalid IOMMU table
Ben found the root cause. Commit
37f02195bee9c25ce44e25204f40b7961a6d7c9d
("powerpc/pci: fix PCI-e devices rescan issue on powerpc platform")
overwrites the IOMMU table of PCI device while enabling PCI device.
The patch intends to fix the IOMMU table after that point.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Gavin Shan [Thu, 25 Apr 2013 19:21:01 +0000 (19:21 +0000)]
powerpc/powernv: Build DMA space for PE on PHB3
The patch intends to build 32-bits DMA space for individual PEs on
PHB3. The TVE# is recognized by the combo of PE# and fixed bits
from DMA address, which is zero for 32-bits DMA space.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Gavin Shan [Thu, 25 Apr 2013 19:21:00 +0000 (19:21 +0000)]
powerpc/powernv: TCE invalidation for PHB3
The TCE should be invalidated while it's created or free'd. The
approach to do that for IODA1 and IODA2 compliant PHBs are different.
So the patch differentiate them with different functions called to
do that for IODA1 and IODA2 compliant PHBs. It's notable that the
PCI address is used to invalidate the corresponding TCE on IODA2
compliant PHB3.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Gavin Shan [Thu, 25 Apr 2013 19:20:59 +0000 (19:20 +0000)]
powerpc/powernv: Patch MSI EOI handler on P8
The EOI handler of MSI/MSI-X interrupts for P8 (PHB3) need additional
steps to handle the P/Q bits in IVE before EOIing the corresponding
interrupt. The patch changes the EOI handler to cover that. we have
individual IRQ chip in each PHB instance. During the MSI IRQ setup
time, the IRQ chip is copied over from the original one for that IRQ,
and the EOI handler is patched with the one that will handle the P/Q
bits (As Ben suggested).
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Gavin Shan [Thu, 25 Apr 2013 19:20:58 +0000 (19:20 +0000)]
powerpc/powernv: Add option CONFIG_POWERNV_MSI
As Michael Ellerman suggested, to add CONFIG_POWERNV_MSI for PowerNV
platform. That's similar to CONFIG_PSERIES_MSI for pSeries platform.
For now, we don't make it dependent on CONFIG_EEH since it's not ready
to enable that yet.
Apart from that, we also enable CONFIG_PPC_MSI_BITMAP on selecting
CONFIG_POWERNV_MSI.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Gavin Shan [Thu, 25 Apr 2013 19:20:57 +0000 (19:20 +0000)]
powerpc/powernv: Supports PHB3
The patch intends to initialize PHB3 during system boot stage. The
flag "PNV_PHB_MODEL_PHB3" is introduced to differentiate IODA2
compatible PHB3 from other types of PHBs.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Paul Mackerras [Thu, 25 Apr 2013 17:51:40 +0000 (17:51 +0000)]
powerpc: Fix "attempt to move .org backwards" error
Building a 64-bit powerpc kernel with PR KVM enabled currently gives
this error:
AS arch/powerpc/kernel/head_64.o
arch/powerpc/kernel/exceptions-64s.S: Assembler messages:
arch/powerpc/kernel/exceptions-64s.S:258: Error: attempt to move .org backwards
make[2]: *** [arch/powerpc/kernel/head_64.o] Error 1
This happens because the MASKABLE_EXCEPTION_PSERIES macro turns into
33 instructions, but we only have space for 32 at the decrementer
interrupt vector (from 0x900 to 0x980).
In the code generated by the MASKABLE_EXCEPTION_PSERIES macro, we
currently have two instances of the HMT_MEDIUM macro, which has the
effect of setting the SMT thread priority to medium. One is the
first instruction, and is overwritten by a no-op on processors where
we save the PPR (processor priority register), that is, POWER7 or
later. The other is after we have saved the PPR.
In order to reduce the code at 0x900 by one instruction, we omit the
first HMT_MEDIUM. On processors without SMT this will have no effect
since HMT_MEDIUM is a no-op there. On POWER5 and RS64 machines this
will mean that the first few instructions take a little longer in the
case where a decrementer interrupt occurs when the hardware thread is
running at low SMT priority. On POWER6 and later machines, the
hardware automatically boosts the thread priority when a decrementer
interrupt is taken if the thread priority was below medium, so this
change won't make any difference.
The alternative would be to branch out of line after saving the CFAR.
However, that would incur an extra overhead on all processors, whereas
the approach adopted here only adds overhead on older threaded processors.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Nathan Fontenot [Wed, 24 Apr 2013 06:07:39 +0000 (06:07 +0000)]
powerpc/pseries: Add /proc interface to control topology updates
There are instances in which we do not want topology updates to occur.
In order to allow this a /proc interface (/proc/powerpc/topology_updates)
is introduced so that topology updates can be enabled and disabled.
This patch also adds a prrn_is_enabled() call so that PRRN events are
handled in the kernel only if topology updating is enabled.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Nathan Fontenot [Wed, 24 Apr 2013 06:06:17 +0000 (06:06 +0000)]
powerpc/pseries: Enable PRRN handling
The Linux kernel and platform firmware negotiate their mutual support
of the PRRN option via the ibm,client-architecture-support interface.
This patch simply sets the appropriate fields in the client architecture
vector to indicate Linux support for PRRN and will allow the firmware to
report PRRN events via the RTAS event-scan mechanism.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Jesse Larrew [Wed, 24 Apr 2013 06:05:22 +0000 (06:05 +0000)]
powerpc/pseries: RE-enable Virtual Processor Home Node updating
The new PRRN firmware feature provides a more convenient and event-driven
interface than VPHN for notifying Linux of changes to the NUMA affinity of
platform resources. However, for practical reasons, it may not be feasible
for some customers to update to the latest firmware. For these customers,
the VPHN feature supported on previous firmware versions may still be the
best option.
The VPHN feature was previously disabled due to races with the load
balancing code when accessing the NUMA cpu maps, but the new stop_machine()
approach protects the NUMA cpu maps from these concurrent accesses. It
should be safe to re-enable this feature now.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Jesse Larrew [Wed, 24 Apr 2013 06:03:48 +0000 (06:03 +0000)]
powerpc/pseries: Update NUMA VDSO information when updating CPU maps
The following patch adds vdso_getcpu_init(), which stores the NUMA node for
a cpu in SPRG3:
Commit
18ad51dd34 ("powerpc: Add VDSO version of getcpu") adds
vdso_getcpu_init(), which stores the NUMA node for a cpu in SPRG3.
This patch ensures that this information is also updated when the NUMA
affinity of a cpu changes.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Nathan Fontenot [Wed, 24 Apr 2013 06:02:13 +0000 (06:02 +0000)]
powerpc/pseries: Use stop machine to update cpu maps
The new PRRN firmware feature allows CPU and memory resources to be
transparently reassigned across NUMA boundaries. When this happens, the
kernel must update the node maps to reflect the new affinity information.
Although the NUMA maps can be protected by locking primitives during the
update itself, this is insufficient to prevent concurrent accesses to these
structures. Since cpumask_of_node() hands out a pointer to these
structures, they can still be modified outside of the lock. Furthermore,
tracking down each usage of these pointers and adding locks would be quite
invasive and difficult to maintain.
The approach used is to make a list of affected cpus and call stop_machine
to have the update routine run on each of the affected cpus allowing them
to update themselves. Each cpu finds itself in the list of cpus and makes
the appropriate updates. We need to have each cpu do this for themselves to
handle calls to vdso_getcpu_init() added in a subsequent patch.
Situations like these are best handled using stop_machine(). Since the NUMA
affinity updates are exceptionally rare events, this approach has the
benefit of not adding any overhead while accessing the NUMA maps during
normal operation.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Jesse Larrew [Wed, 24 Apr 2013 06:00:35 +0000 (06:00 +0000)]
powerpc/pseries: Update CPU maps when device tree is updated
Platform events such as partition migration or the new PRRN firmware
feature can cause the NUMA characteristics of a CPU to change, and these
changes will be reflected in the device tree nodes for the affected
CPUs.
This patch registers a handler for Open Firmware device tree updates
and reconfigures the CPU and node maps whenever the associativity
changes. Currently, this is accomplished by marking the affected CPUs in
the cpu_associativity_changes_mask and allowing
arch_update_cpu_topology() to retrieve the new associativity information
using hcall_vphn().
Protecting the NUMA cpu maps from concurrent access during an update
operation will be addressed in a subsequent patch in this series.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Nathan Fontenot [Wed, 24 Apr 2013 05:58:23 +0000 (05:58 +0000)]
powerpc/pseries: Update numa.c to use updated firmware_has_feature()
Update the numa code to use the updated firmware_has_feature() when checking
for type 1 affinity.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Nathan Fontenot [Wed, 24 Apr 2013 05:57:18 +0000 (05:57 +0000)]
powerpc/pseries: Update firmware_has_feature() to check architecture vector 5 bits
The firmware_has_feature() function makes it easy to check for supported
features of the hypervisor. This patch extends the capability of
firmware_has_feature() to include checking for specified bits
in vector 5 of the architecture vector as reported in the device tree.
As part of this the #defines used for the architecture vector are re-defined
such that each option has the index into vector 5 and the feature bit encoded
into it. This makes checking for architecture bits when initiating data
for firmware_has_feature much easier.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Nathan Fontenot [Wed, 24 Apr 2013 05:55:08 +0000 (05:55 +0000)]
powerpc/pseries: Use ARRAY_SIZE to iterate over firmware_features_table array
When iterating over the entries in firmware_features_table we only need
to go over the actual number of entries in the array instead of declaring
it to be bigger and checking to make sure there is a valid entry in every
slot.
This patch removes the FIRMWARE_MAX_FEATURES #define and replaces the
array looping with the use of ARRAY_SIZE().
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Nathan Fontenot [Wed, 24 Apr 2013 05:53:10 +0000 (05:53 +0000)]
powerpc/pseries: Move architecture vector definitions to prom.h
As part of handling of PRRN events we need to check vector 5 of the
architecture vector bits reported in the device tree to ensure PRRN event
handling is enabled. To do this firmware_has_feature() is updated (in a
subsequent patch) to make this check vector 5 bits. To avoid having to
re-define bits in the architecture vector the bit definitions are moved
to prom.h.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Jesse Larrew [Wed, 24 Apr 2013 05:51:33 +0000 (05:51 +0000)]
powerpc/pseries: Add PRRN RTAS event handler
A PRRN event is signaled via the RTAS event-scan mechanism, which
returns a Hot Plug Event message "fixed part" indicating "Platform
Resource Reassignment". In response to the Hot Plug Event message,
we must call ibm,update-nodes to determine which resources were
reassigned and then ibm,update-properties to obtain the new affinity
information about those resources.
The PRRN event-scan RTAS message contains only the "fixed part" with
the "Type" field set to the value 160 and no Extended Event Log. The
four-byte Extended Event Log Length field is re-purposed (since no
Extended Event Log message is included) to pass the "scope" parameter
that causes the ibm,update-nodes to return the nodes affected by the
specific resource reassignment.
This patch adds a handler for RTAS events. The function
pseries_devicetree_update() (from mobility.c) is used to make the
ibm,update-nodes/ibm,update-properties RTAS calls. Updating the NUMA maps
(handled by a subsequent patch) will require significant processing,
so pseries_devicetree_update() is called from an asynchronous workqueue
to allow event processing to continue.
PRRN RTAS events on pseries systems are rare events that have to be
initiated from the HMC console for the system by an IBM tech. This allows
us to assume that these events are widely spaced. Additionally, all work
on the queue is flushed before handling any new work to ensure we only have
one event in flight being handled at a time.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Nathan Fontenot [Wed, 24 Apr 2013 05:49:36 +0000 (05:49 +0000)]
powerpc/pseries: Correct buffer parsing in update_dt_node()
Correct parsing of the buffer returned from ibm,update-properties. The first
element is a length and the path to the property which is slightly different
from the list of properties in the buffer so we need to specifically
handle this.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Nathan Fontenot [Wed, 24 Apr 2013 05:47:11 +0000 (05:47 +0000)]
powerpc/pseries: Expose pseries devicetree_update()
Newer firmware on Power systems can transparently reassign platform resources
(CPU and Memory) in use. For instance, if a processor or memory unit is
predicted to fail, the platform may transparently move the processing to an
equivalent unused processor or the memory state to an equivalent unused
memory unit. However, reassigning resources across NUMA boundaries may alter
the performance of the partition. When such reassignment is necessary, the
Platform Resource Reassignment Notification (PRRN) option provides a
mechanism to inform the Linux kernel of changes to the NUMA affinity of
its platform resources.
When rtasd receives a PRRN event, it needs to make a series of RTAS
calls (ibm,update-nodes and ibm,update-properties) to retrieve the
updated device tree information. These calls are already handled in the
pseries_devicetree_update() routine used in partition migration.
This patch exposes pseries_devicetree_update() to make it accessible
to other pseries routines, this patch also updates pseries_devicetree_update()
to take a 32-bit scope parameter. The scope value, which was previously hard
coded to 1 for partition migration, is used for the RTAS calls
ibm,update-nodes/properties to update the device tree.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Michael Neuling [Thu, 25 Apr 2013 15:30:57 +0000 (15:30 +0000)]
powerpc: Fix hardware IRQs with MMU on exceptions when HV=0
POWER8 allows us to take interrupts with the MMU on. This gives us a
second set of vectors offset at 0x4000.
Unfortunately when coping these vectors we missed checking for MSR HV
for hardware interrupts (0x500). This results in us trying to use
HSRR0/1 when HV=0, rather than SRR0/1 on HW IRQs
The below fixes this to check CPU_FTR_HVMODE when patching the code at
0x4500.
Also we remove the check for CPU_FTR_ARCH_206 since relocation on IRQs
are only available in arch 2.07 and beyond.
Thanks to benh for helping find this.
Signed-off-by: Michael Neuling <mikey@neuling.org>
CC: <stable@vger.kernel.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Michael Neuling [Wed, 24 Apr 2013 21:00:37 +0000 (21:00 +0000)]
powerpc/power8: Fix secondary CPUs hanging on boot for HV=0
In __restore_cpu_power8 we determine if we are HV and if not, we return
before setting HV only resources.
Unfortunately we forgot to restore the link register from r11 before
returning.
This will happen on boot and with secondary CPUs not coming online.
This adds the missing link register restore.
Signed-off-by: Michael Neuling <mikey@neuling.org>
CC: <stable@vger.kernel.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Michael Neuling [Wed, 24 Apr 2013 00:30:09 +0000 (00:30 +0000)]
powerpc: Add isync to copy_and_flush
In __after_prom_start we copy the kernel down to zero in two calls to
copy_and_flush. After the first call (copy from 0 to copy_to_here:)
we jump to the newly copied code soon after.
Unfortunately there's no isync between the copy of this code and the
jump to it. Hence it's possible that stale instructions could still be
in the icache or pipeline before we branch to it.
We've seen this on real machines and it's results in no console output
after:
calling quiesce...
returning from prom_init
The below adds an isync to ensure that the copy and flushing has
completed before any branching to the new instructions occurs.
Signed-off-by: Michael Neuling <mikey@neuling.org>
CC: <stable@vger.kernel.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Michael Neuling [Wed, 17 Apr 2013 17:33:11 +0000 (17:33 +0000)]
powerpc: Add HWCAP2 aux entry
We are currently out of free bits in AT_HWCAP. With POWER8, we have
several hardware features that we need to advertise.
Tested on POWER and x86.
Signed-off-by: Michael Neuling <michael@neuling.org>
Signed-off-by: Nishanth Aravamudan <nacc@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Benjamin Herrenschmidt [Wed, 24 Apr 2013 05:15:33 +0000 (15:15 +1000)]
powerpc/powernv: Fix missing Kconfig dependency for MSIs
We need PPC_MSI_BITMAP support
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Benjamin Herrenschmidt [Wed, 24 Apr 2013 04:43:36 +0000 (14:43 +1000)]
Merge remote-tracking branch 'origin/master' into next
Merge upstream to get the audit fixes
Michael Ellerman [Tue, 23 Apr 2013 15:13:14 +0000 (15:13 +0000)]
powerpc/spufs: Initialise inode->i_ino in spufs_new_inode()
In commit 85fe402 (fs: do not assign default i_ino in new_inode), the
initialisation of i_ino was removed from new_inode() and pushed down
into the callers. However spufs_new_inode() was not updated.
This exhibits as no files appearing in /spu, because all our dirents
have a zero inode, which readdir() seems to dislike.
Cc: stable@vger.kernel.org
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Vasant Hegde [Tue, 23 Apr 2013 04:22:22 +0000 (04:22 +0000)]
powerpc/rtas_flash: New return code to indicate FW entitlement expiry
Add new return code to rtas_flash to indicate firmware entitlement
expiry. Strictly we don't need this update. But to keep it in sync
with PAPR, this was added.
Signed-off-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Signed-off-by: Vasant Hegde <hegdevasant@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Vasant Hegde [Tue, 23 Apr 2013 04:20:48 +0000 (04:20 +0000)]
powerpc/rtas_flash: Update return token comments
Add proper comment to ibm,validate-flash-image RTAS call
update result tokens.
Note: Only comment section is modified, no code change.
Signed-off-by: Vasant Hegde <hegdevasant@linux.vnet.ibm.com>
Signed-off-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Michael Ellerman [Tue, 23 Apr 2013 02:14:51 +0000 (02:14 +0000)]
powerpc/cell: Only iterate over online nodes in cbe_init_pm_irq()
None of the cell platforms support CPU hotplug, so we should iterate
only over online nodes when setting PMU interrupts.
This also fixes a warning during boot when NODES_SHIFT is large enough:
WARNING: at /scratch/michael/src/kmk/linus/kernel/irq/irqdomain.c:766
...
NIP [
c0000000000db278] .irq_linear_revmap+0x30/0x58
LR [
c0000000000dc2a0] .irq_create_mapping+0x38/0x1a8
Call Trace:
[
c0000003fc9c3af0] [
c0000000000dc2a0] .irq_create_mapping+0x38/0x1a8 (unreliable)
[
c0000003fc9c3b80] [
c000000000655c1c] .__machine_initcall_cell_cbe_init_pm_irq+0x84/0x158
[
c0000003fc9c3c20] [
c00000000000afb4] .do_one_initcall+0x5c/0x1e0
[
c0000003fc9c3cd0] [
c000000000644580] .kernel_init_freeable+0x238/0x328
[
c0000003fc9c3db0] [
c00000000000b784] .kernel_init+0x1c/0x120
[
c0000003fc9c3e30] [
c000000000009fb8] .ret_from_kernel_thread+0x64/0xac
This is caused by us overflowing our linear revmap because we're
requesting too many interrupts.
Reported-by: Dennis Schridde <devurandom@gmx.net>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Benjamin Herrenschmidt [Wed, 24 Apr 2013 04:11:20 +0000 (14:11 +1000)]
Merge remote-tracking branch 'mpe/master' into next
Merge the tentative powerpc-next branch maintained by Michael
while I was on vacation
Chen Gang [Mon, 22 Apr 2013 17:12:54 +0000 (17:12 +0000)]
powerpc/pseries/lparcfg: Fix possible overflow are more than 1026
need set '\0' for 'local_buffer'.
SPLPAR_MAXLENGTH is 1026, RTAS_DATA_BUF_SIZE is 4096. so the contents of
rtas_data_buf may truncated in memcpy.
if contents are really truncated.
the splpar_strlen is more than 1026. the next while loop checking will
not find the end of buffer. that will cause memory access violation.
Signed-off-by: Chen Gang <gang.chen@asianux.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Andy Shevchenko [Mon, 22 Apr 2013 03:02:19 +0000 (03:02 +0000)]
powerpc/pmac/smu: Use %*ph to print small buffers
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Oleg Nesterov [Sun, 21 Apr 2013 06:47:59 +0000 (06:47 +0000)]
ptrace/powerpc: Don't flush_ptrace_hw_breakpoint() on fork()
arch_dup_task_struct() does flush_ptrace_hw_breakpoint(src), this
destroys the parent's breakpoints for no reason. We should clear
child->thread.ptrace_bps[] copied by dup_task_struct() instead.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Adhemerval Zanella [Mon, 22 Apr 2013 09:29:33 +0000 (09:29 +0000)]
powerpc: Add VDSO version of time
On 04/18/2013 07:38 PM, Anton Blanchard wrote:
> Since you are only reading one long you shouldn't need to check the
> update count and loop, you will always see a consistent value. The
> system call version of time() just does an unprotected load for example.
Fixed.
> With the above change and with Michael's comments covered (decent
> changelog entry and Signed-off-by):
>
> Acked-by: Anton Blanchard <anton@samba.org>
Thanks for the review, below the updated patch:
From: Adhemerval Zanella <azanella@linux.vnet.ibm.com>
This patch implement the time syscall as vDSO. The performance speedups
are:
Baseline PPC32: 380 nsec
Baseline PPC64: 350 nsec
vdso PPC32: 20 nsec
vsdo PPC64: 20 nsec
Tested on 64 bit build with both 32 bit and 64 bit userland.
Acked-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Adhemerval Zanella <azanella@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Linus Torvalds [Sun, 21 Apr 2013 21:38:45 +0000 (14:38 -0700)]
Linux 3.9-rc8
Linus Torvalds [Sun, 21 Apr 2013 17:25:42 +0000 (10:25 -0700)]
Merge branch 'perf-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull perf fixes from Ingo Molnar:
"Misc fixes"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/x86: Fix offcore_rsp valid mask for SNB/IVB
perf: Treat attr.config as u64 in perf_swevent_init()
Linus Torvalds [Sun, 21 Apr 2013 17:16:56 +0000 (10:16 -0700)]
Merge branch 'vm_ioremap_memory-examples'
I'm going to do an -rc8, so I'm just going to do this rather than delay
it any further. They are arguably stable material anyway.
* vm_ioremap_memory-examples:
mtdchar: remove no-longer-used vma helpers
vm: convert snd_pcm_lib_mmap_iomem() to vm_iomap_memory() helper
vm: convert fb_mmap to vm_iomap_memory() helper
vm: convert mtdchar mmap to vm_iomap_memory() helper
vm: convert HPET mmap to vm_iomap_memory() helper
Linus Torvalds [Sun, 21 Apr 2013 01:40:36 +0000 (18:40 -0700)]
Merge branch 'x86-kdump-for-linus' of git://git./linux/kernel/git/tip/tip
Pull kdump fixes from Peter Anvin:
"The kexec/kdump people have found several problems with the support
for loading over 4 GiB that was introduced in this merge cycle. This
is partly due to a number of design problems inherent in the way the
various pieces of kdump fit together (it is pretty horrifically manual
in many places.)
After a *lot* of iterations this is the patchset that was agreed upon,
but of course it is now very late in the cycle. However, because it
changes both the syntax and semantics of the crashkernel option, it
would be desirable to avoid a stable release with the broken
interfaces."
I'm not happy with the timing, since originally the plan was to release
the final 3.9 tomorrow. But apparently I'm doing an -rc8 instead...
* 'x86-kdump-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
kexec: use Crash kernel for Crash kernel low
x86, kdump: Change crashkernel_high/low= to crashkernel=,high/low
x86, kdump: Retore crashkernel= to allocate under 896M
x86, kdump: Set crashkernel_low automatically
Linus Torvalds [Sun, 21 Apr 2013 01:38:48 +0000 (18:38 -0700)]
Merge branch 'x86-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull x86 fixes from Peter Anvin:
"Three groups of fixes:
1. Make sure we don't execute the early microcode patching if family
< 6, since it would touch MSRs which don't exist on those
families, causing crashes.
2. The Xen partial emulation of HyperV can be dealt with more
gracefully than just disabling the driver.
3. More EFI variable space magic. In particular, variables hidden
from runtime code need to be taken into account too."
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, microcode: Verify the family before dispatching microcode patching
x86, hyperv: Handle Xen emulation of Hyper-V more gracefully
x86,efi: Implement efi_no_storage_paranoia parameter
efi: Export efi_query_variable_store() for efivars.ko
x86/Kconfig: Make EFI select UCS2_STRING
efi: Distinguish between "remaining space" and actually used space
efi: Pass boot services variable info to runtime code
Move utf16 functions to kernel core and rename
x86,efi: Check max_size only if it is non-zero.
x86, efivars: firmware bug workarounds should be in platform code
Linus Torvalds [Sun, 21 Apr 2013 01:38:06 +0000 (18:38 -0700)]
Merge branch 'fixes' of git://git.linaro.org/people/rmk/linux-arm
Pull ARM fixes from Russell King:
"A set of fixes from various people - Will Deacon gets a prize for
removing code this time around. The biggest fix in this lot is
sorting out the ARM740T mess. The rest are relatively small fixes."
* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
ARM: 7699/1: sched_clock: Add more notrace to prevent recursion
ARM: 7698/1: perf: fix group validation when using enable_on_exec
ARM: 7697/1: hw_breakpoint: do not use __cpuinitdata for dbg_cpu_pm_nb
ARM: 7696/1: Fix kexec by setting outer_cache.inv_all for Feroceon
ARM: 7694/1: ARM, TCM: initialize TCM in paging_init(), instead of setup_arch()
ARM: 7692/1: iop3xx: move IOP3XX_PERIPHERAL_VIRT_BASE
ARM: modules: don't export cpu_set_pte_ext when !MMU
ARM: mm: remove broken condition check for v4 flushing
ARM: mm: fix numerous hideous errors in proc-arm740.S
ARM: cache: remove ARMv3 support code
ARM: tlbflush: remove ARMv3 support
Linus Torvalds [Sun, 21 Apr 2013 01:23:08 +0000 (18:23 -0700)]
Merge git://git./linux/kernel/git/davem/sparc
Pull sparc fixes from David Miller:
1) Fix race in sparc64 TLB shootdowns, we have to synchronize with the
sibling cpus completing if we are passing them a reference via
pointer to a data structure.
2) Fix cleaning of bitmaps in sparc32, from Akinobu Mita.
3) Fix various sparc header mistakes, some of which resulted in
userland build breakage. From Sam Ravnborg.
4) Kill ghost declarations and defines missed when several bits of code
got deleted recently.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sparc64: Fix race in TLB batch processing.
sparc: use asm-generic version of types.h
bbc_i2c: fix section mismatch warning
sparc: use generic headers
sparc:cleanup unused code in smp_32.h
sparc/iommu: fix typo s/265KB/256KB/
sparc/srmmu: clear trailing edge of bitmap properly
sparc:remove unused declaration smp_boot_cpus()
Linus Torvalds [Sun, 21 Apr 2013 01:21:05 +0000 (18:21 -0700)]
Merge git://git./linux/kernel/git/davem/net
Pull networking updates from David Miller:
1) ax88796 does 64-bit divides which causes link errors on ARM, fix
from Arnd Bergmann.
2) Once an improper offload setting is detected on an SKB we don't rate
limit the log message so we can very easily live lock. From Ben
Greear.
3) Openvswitch cannot report vport configuration changes reliably
because it didn't preallocate the netlink notification message
before changing state. From Jesse Gross.
4) The effective UID/GID SCM credentials fix, from Linus.
5) When a user explicitly asks for wireless authentication, cfg80211
isn't told about the AP detachment leaving inconsistent state. Fix
from Johannes Berg.
6) Fix self-MAC checks in batman-adv on multi-mesh nodes, from Antonio
Quartulli.
7) Revert build_skb() change sin IGB driver, can result in memory
corruption. From Alexander Duyck.
8) Fix setting VLANs on virtual functions in IXGBE, from Greg Rose.
9) Fix TSO races in qlcnic driver, from Sritej Velaga.
10) In bnx2x the kernel driver and UNDI firmware can try to program the
chip at the same time, resulting in corruption. Add proper
synchronization. From Dmitry Kravkov.
11) Fix corruption of status block in firmware ram in bxn2x, from Ariel
Elior.
12) Fix load balancing hash regression of bonding driver in forwarding
configurations, from Eric Dumazet.
13) Fix TS ECR regression in TCP by calling tcp_replace_ts_recent() in
all the right spots, from Eric Dumazet.
14) Fix several bonding bugs having to do with address manintainence,
including not removing address when configuration operations
encounter errors, missed locking on the address lists, missing
refcounting on VLAN objects, etc. All from Nikolay Aleksandrov.
15) Add workarounds for firmware bugs in LTE qmi_wwan devices, wherein
the devices fail to add a proper ethernet header while on LTE
networks but otherwise properly do so on 2G and 3G ones. From Bjørn
Mork.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (38 commits)
net: fix incorrect credentials passing
net: rate-limit warn-bad-offload splats.
net: ax88796: avoid 64 bit arithmetic
qlge: Update version to 1.00.00.32.
qlge: Fix ethtool autoneg advertising.
qlge: Fix receive path to drop error frames
net: qmi_wwan: prevent duplicate mac address on link (firmware bug workaround)
net: qmi_wwan: fixup destination address (firmware bug workaround)
net: qmi_wwan: fixup missing ethernet header (firmware bug workaround)
bonding: in bond_mc_swap() bond's mc addr list is walked without lock
bonding: disable netpoll on enslave failure
bonding: primary_slave & curr_active_slave are not cleaned on enslave failure
bonding: vlans don't get deleted on enslave failure
bonding: mc addresses don't get deleted on enslave failure
pkt_sched: fix error return code in fw_change_attrs()
irda: small read past the end of array in debug code
tcp: call tcp_replace_ts_recent() from tcp_ack()
netfilter: xt_rpfilter: skip locally generated broadcast/multicast, too
netfilter: ipset: bitmap:ip,mac: fix listing with timeout
bonding: fix l23 and l34 load balancing in forwarding path
...
Linus Torvalds [Fri, 19 Apr 2013 15:32:32 +0000 (15:32 +0000)]
net: fix incorrect credentials passing
Commit
257b5358b32f ("scm: Capture the full credentials of the scm
sender") changed the credentials passing code to pass in the effective
uid/gid instead of the real uid/gid.
Obviously this doesn't matter most of the time (since normally they are
the same), but it results in differences for suid binaries when the wrong
uid/gid ends up being used.
This just undoes that (presumably unintentional) part of the commit.
Reported-by: Andy Lutomirski <luto@amacapital.net>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Serge E. Hallyn <serge@hallyn.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Acked-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
H. Peter Anvin [Sat, 20 Apr 2013 00:09:03 +0000 (17:09 -0700)]
Merge remote-tracking branch 'efi/urgent' into x86/urgent
Matt Fleming (1):
x86, efivars: firmware bug workarounds should be in platform
code
Matthew Garrett (3):
Move utf16 functions to kernel core and rename
efi: Pass boot services variable info to runtime code
efi: Distinguish between "remaining space" and actually used
space
Richard Weinberger (2):
x86,efi: Check max_size only if it is non-zero.
x86,efi: Implement efi_no_storage_paranoia parameter
Sergey Vlasov (2):
x86/Kconfig: Make EFI select UCS2_STRING
efi: Export efi_query_variable_store() for efivars.ko
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
H. Peter Anvin [Fri, 19 Apr 2013 23:36:03 +0000 (16:36 -0700)]
x86, microcode: Verify the family before dispatching microcode patching
For each CPU vendor that implements CPU microcode patching, there will
be a minimum family for which this is implemented. Verify this
minimum level of support.
This can be done in the dispatch function or early in the application
functions. Doing the latter turned out to be somewhat awkward because
of the ineviable split between the BSP and the AP paths, and rather
than pushing deep into the application functions, do this in
the dispatch function.
Reported-by: "Bryan O'Donoghue" <bryan.odonoghue.lkml@nexus-software.ie>
Suggested-by: Borislav Petkov <bp@alien8.de>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Link: http://lkml.kernel.org/r/1366392183-4149-1-git-send-email-bryan.odonoghue.lkml@nexus-software.ie
Ben Greear [Fri, 19 Apr 2013 10:45:52 +0000 (10:45 +0000)]
net: rate-limit warn-bad-offload splats.
If one does do something unfortunate and allow a
bad offload bug into the kernel, this the
skb_warn_bad_offload can effectively live-lock the
system, filling the logs with the same error over
and over.
Add rate limitation to this so that box remains otherwise
functional in this case.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Arnd Bergmann [Fri, 19 Apr 2013 08:47:26 +0000 (08:47 +0000)]
net: ax88796: avoid 64 bit arithmetic
When building ax88796 on an ARM platform with 64-bit resource_size_t,
we currently get
drivers/net/ethernet/8390/ax88796.c:875: undefined reference to `__aeabi_uldivmod'
because we do a division on the length of the MMIO resource.
Since we know that this resource is very short, using an
"unsigned long" instead of "resource_size_t" is entirely
sufficient, and avoids this link-time error.
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: netdev@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jitendra Kalsaria [Thu, 18 Apr 2013 19:49:54 +0000 (19:49 +0000)]
qlge: Update version to 1.00.00.32.
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jitendra Kalsaria [Thu, 18 Apr 2013 19:49:53 +0000 (19:49 +0000)]
qlge: Fix ethtool autoneg advertising.
Autoneg is supported on specific port types only. Fix the driver to advertise
autoneg based on the port type.
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sritej Velaga [Thu, 18 Apr 2013 19:49:52 +0000 (19:49 +0000)]
qlge: Fix receive path to drop error frames
o Fix the driver to drop error frames in the receive path
o Update error counter which was not getting incremented
Signed-off-by: Sritej Velaga <sritej.velaga@qlogic.com>
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 19 Apr 2013 21:51:26 +0000 (17:51 -0400)]
Merge branch 'qmi_wwan'
Bjørn Mork says:
====================
This series adds workarounds for 3 different firmware bugs, each
preventing the affected devices from working at all. I therefore
humbly request that these fixes go to stable-3.8 (if still
maintained) and 3.9 (either via net if still possible, or via
stable if not).
All 3 workarounds are applied to all devices supported by the driver.
Adding quirks for specific devices was considered as an alternative,
but was rejected because we have too little information about the
exact distribution of the buggy firmwares. All we know is that the
same bug shows up in devices from at least 3 different, and presumably
independent, vendors.
The workarounds have instead been designed to automatically apply
when necessary, and to have as little impact as possible on unaffected
devices. The series has been tested on a number of devices both with
and without these bugs.
The series should apply cleanly to net/master, net-next/master and
stable/linux-3.8.y
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Bjørn Mork [Thu, 18 Apr 2013 12:57:11 +0000 (12:57 +0000)]
net: qmi_wwan: prevent duplicate mac address on link (firmware bug workaround)
We normally trust and use the CDC functional descriptors provided by a
number of devices. But some of these will erroneously list the address
reserved for the device end of the link. Attempting to use this on
both the device and host side will naturally not work.
Work around this bug by ignoring the functional descriptor and assign a
random address instead in this case.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bjørn Mork [Thu, 18 Apr 2013 12:57:10 +0000 (12:57 +0000)]
net: qmi_wwan: fixup destination address (firmware bug workaround)
Received packets are sometimes addressed to 00:a0:c6:00:00:00
instead of the address the device firmware should have learned
from the host:
321.224126 77.16.85.204 -> 148.122.171.134 ICMP 98 Echo (ping) request id=0x4025, seq=64/16384, ttl=64
0000 82 c0 82 c9 f1 67 82 c0 82 c9 f1 67 08 00 45 00 .....g.....g..E.
0010 00 54 00 00 40 00 40 01 57 cc 4d 10 55 cc 94 7a .T..@.@.W.M.U..z
0020 ab 86 08 00 62 fc 40 25 00 40 b2 bc 6e 51 00 00 ....b.@%.@..nQ..
0030 00 00 6b bd 09 00 00 00 00 00 10 11 12 13 14 15 ..k.............
0040 16 17 18 19 1a 1b 1c 1d 1e 1f 20 21 22 23 24 25 .......... !"#$%
0050 26 27 28 29 2a 2b 2c 2d 2e 2f 30 31 32 33 34 35 &'()*+,-./012345
0060 36 37 67
321.240607 148.122.171.134 -> 77.16.85.204 ICMP 98 Echo (ping) reply id=0x4025, seq=64/16384, ttl=55
0000 00 a0 c6 00 00 00 02 50 f3 00 00 00 08 00 45 00 .......P......E.
0010 00 54 00 56 00 00 37 01 a0 76 94 7a ab 86 4d 10 .T.V..7..v.z..M.
0020 55 cc 00 00 6a fc 40 25 00 40 b2 bc 6e 51 00 00 U...j.@%.@..nQ..
0030 00 00 6b bd 09 00 00 00 00 00 10 11 12 13 14 15 ..k.............
0040 16 17 18 19 1a 1b 1c 1d 1e 1f 20 21 22 23 24 25 .......... !"#$%
0050 26 27 28 29 2a 2b 2c 2d 2e 2f 30 31 32 33 34 35 &'()*+,-./012345
0060 36 37 67
The bogus address is always the same, and matches the address
suggested by many devices as a default address. It is likely a
hardcoded firmware default.
The circumstances where this bug has been observed indicates that
the trigger is related to timing or some other factor the host
cannot control. Repeating the exact same configuration sequence
that caused it to trigger once, will not necessarily cause it to
trigger the next time. Reproducing the bug is therefore difficult.
This opens up a possibility that the bug is more common than we can
confirm, because affected devices often will work properly again
after a reset. A procedure most users are likely to try out before
reporting a bug.
Unconditionally rewriting the destination address if the first digit
of the received packet is 0, is considered an acceptable compromise
since we already have to inspect this digit. The simplification will
cause unnecessary rewrites if the real address starts with 0, but this
is still better than adding additional tests for this particular case.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bjørn Mork [Thu, 18 Apr 2013 12:57:09 +0000 (12:57 +0000)]
net: qmi_wwan: fixup missing ethernet header (firmware bug workaround)
A number of LTE devices from different vendors all suffer from the
same firmware bug: Most of the packets received from the device while
it is attached to a LTE network will not have an ethernet header. The
devices work as expected when attached to 2G or 3G networks, sending
an ethernet header with all packets.
This driver is not aware of which network the modem attached to, and
even if it were there are still some packet types which are always
received with the header intact.
All devices supported by this driver have severely limited
networking capabilities:
- can only transmit IPv4, IPv6 and possibly ARP
- can only support a single host hardware address at any time
- will only do point-to-point communcation with the host
Because of this, we are able to reliably identify any bogus raw IP
packets by simply looking at the 4 IP version bits. All we need to
do is to avoid 4 or 6 in the first digit of the mac address. This
workaround ensures this, and fix up the received packets as necessary.
Given the distribution of the bug, it is believed that the source is
the chipset vendor. The devices which are verified to be affected are:
Huawei E392u-12 (Qualcomm MDM9200)
Pantech UML290 (Qualcomm MDM9600)
Novatel USB551L (Qualcomm MDM9600)
Novatel E362 (Qualcomm MDM9600)
It is believed that the bug depend on firmware revision, which means
that possibly all devices based on the above mentioned chipset may be
affected if we consider all available firmware revisions.
The information about affected devices and versions is likely
incomplete. As the additional overhead for packets not needing this
fixup is very small, it is considered acceptable to apply the
workaround to all devices handled by this driver.
Reported-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 19 Apr 2013 21:49:11 +0000 (17:49 -0400)]
Merge branch 'bonding'
Nikolay Aleksandrov says:
====================
This patch-set fixes mainly bugs on enslave failure and one occasion
of a needed locking. The patches are:
1. On enslave failure mc addresses are not flushed from the slave
2. On enslave failure vlans are not cleaned up from the slave
3. On enslave failure the bond's primary and curr_active_slave
are not cleaned up (which might result in use of freed memory)
4. On enslave failure netpoll is not disabled which might result in
a memory leak
5. In bond_mc_swap() the bond's mc addr list is walked without
netif_addr_lock, since it can be called without rtnl, add it
v2: patch 01 - fix log message and remove unnecessary code move
====================
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
nikolay@redhat.com [Thu, 18 Apr 2013 07:33:38 +0000 (07:33 +0000)]
bonding: in bond_mc_swap() bond's mc addr list is walked without lock
Use netif_addr_lock_bh() to acquire the appropriate lock before walking.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
nikolay@redhat.com [Thu, 18 Apr 2013 07:33:37 +0000 (07:33 +0000)]
bonding: disable netpoll on enslave failure
slave_disable_netpoll() is not called upon enslave failure which would
lead to a memory leak. Call slave_disable_netpoll() after err_detach as
that's the first error path after enabling netpoll on that slave.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
nikolay@redhat.com [Thu, 18 Apr 2013 07:33:36 +0000 (07:33 +0000)]
bonding: primary_slave & curr_active_slave are not cleaned on enslave failure
On enslave failure primary_slave can point to new_slave which is to be
freed, and the same applies to curr_active_slave. So check if this is
the case and clean up properly after err_detach because that's the first
error code path after they're set.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
nikolay@redhat.com [Thu, 18 Apr 2013 07:33:35 +0000 (07:33 +0000)]
bonding: vlans don't get deleted on enslave failure
The main problem is with vid refcount which only gets bumped up.
Delete the vlans after err_detach as that's the first error path
after the vlans are added.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
nikolay@redhat.com [Thu, 18 Apr 2013 07:33:34 +0000 (07:33 +0000)]
bonding: mc addresses don't get deleted on enslave failure
Add bond_mc_list_flush() after err_detach as that's the first error path
after the addresses are added. The main issue is the mc addresses' refcount
which only gets bumped up.
v2: update log message and don't move code unnecessarily
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wei Yongjun [Wed, 17 Apr 2013 16:49:10 +0000 (16:49 +0000)]
pkt_sched: fix error return code in fw_change_attrs()
Fix to return -EINVAL when tb[TCA_FW_MASK] is set and head->mask != 0xFFFFFFFF
instead of 0 (ifdef CONFIG_NET_CLS_IND and tb[TCA_FW_INDEV]), as done elsewhere
in this function.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>