ide: ide_timing_compute() fixup

XFER_SW_DMA_0 mode should be excluded from the extended cycle
timing computations.

[ This is just a documentation fix -- code inside the affected
  'if' block already makes sure to accept only PIO modes. ]

Noticed-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ide: make ide_get_best_pio_mode() static

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

via82cxxx: use ->pio_mode value to determine pair device speed

Use the current PIO mode value instead of the current transfer speed
of the pair device on the port to determine PIO commmand timings used
for both devices on the port.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tx493xide: use ->pio_mode value to determine pair device speed

Use the current PIO mode value instead of the physical maximum one
of the pair device on the port to determine PIO commmand timings used
for both devices on the port.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

siimage: use ->pio_mode value to determine pair device speed

Use the current PIO mode value instead of the physical maximum one
of the pair device on the port to determine PIO commmand timings used
for both devices on the port.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

palm_bk3710: use ->pio_mode value to determine pair device speed

Use the current PIO mode value instead of the physical maximum one
of the pair device on the port to determine PIO commmand timings used
for both devices on the port.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

it821x: use ->pio_mode value to determine pair device speed

Use the current PIO mode value instead of the physical maximum one
of the pair device on the port to determine PIO commmand timings used
for both devices on the port.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

cs5536: use ->pio_mode value to determine pair device speed

Use the current PIO mode value instead of the physical maximum one
of the pair device on the port to determine PIO commmand timings used
for both devices on the port.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

cs5535: use ->pio_mode value to determine pair device speed

Use the current PIO mode value instead of the physical maximum one
of the pair device on the port to determine PIO commmand timings used
for both devices on the port.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

cmd64x: fix handling of address setup timings

Account for the requirements of the DMA mode currently used.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

amd74xx: use ->pio_mode value to determine pair device speed

Use the current PIO mode value instead of the current transfer speed
of the pair device on the port to determine PIO commmand timings used
for both devices on the port.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

alim15x3: fix handling of UDMA enable bit

Clear UDMA enable bit also for PIO modes.

Based on libata pata_ali host driver.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

alim15x3: fix handling of DMA timings

Stop depending on the BIOS setup.

Based on libata pata_ali host driver.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

alim15x3: fix handling of command timings

Stop depending on the BIOS setup.

Based on libata pata_ali host driver.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

alim15x3: fix handling of address setup timings

Account for the requirements of the other device on the port.

Based on libata pata_ali host driver.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ide-timings: use ->pio_mode value to determine fastest PIO speed

Use the current PIO mode value instead of the physical maximum one
to determine the fastest allowed PIO for shared PIO/DMA timings.

Affected host drivers: amd74xx and via82cxxx.

[ Update comment to match -DaveM ]

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ide: change ->set_dma_mode method parameters

Change ->set_dma_mode method parameters to match ->set_dmamode method
used in struct ata_port_operations.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

ide: change ->set_pio_mode method parameters

Change ->set_pio_mode method parameters to match ->set_piomode method
used in struct ata_port_operations.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ide: add drive->dma_mode field

Add dma_mode field to ide_drive_t matching dma_mode field used in
struct ata_device.

The validity of the field is restricted to ->dma_pio_mode method
only currently in IDE subsystem.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ide: add drive->pio_mode field

Add pio_mode field to ide_drive_t matching pio_mode field used in
struct ata_device.

The validity of the field is restricted to ->set_pio_mode method
only currently in IDE subsystem.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

via82cxxx: fix UDMA settings programming

* preserve 80-wire cable detection bit
* don't clear UDMA settings when programming PIO/MWDMA modes

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

via82cxxx: add support for VT6415 PCIE PATA IDE Host Controller

Based on commits 5955c7a and 7d948b1 for pata_via host driver.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

via82cxxx: add support for vt8261 and future chips

Based on commit e4d866c for pata_via host driver.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

via82cxxx: workaround h/w bugs

Add custom struct ide_tp_ops instance to fix the internal bug of some VIA
chipsets which will reset the device register after changing the nIEN bit
in the device control register.

Based on commit bfce5e0 for pata_via host driver.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

via82cxxx: fix SATA cable detection

Add VIA_SATA_PATA flag for cx700, vx800 and vx855 chipsets
(the first port is SATA).

Based on commits 7585eb1, bfce5e0 and e4d866c for pata_via
host driver.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ide: add SATA cable detection support

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

via82cxxx: vx855 is a single channel controller

Based on commit e4d866c for pata_via host driver
(PCI ID was later changed by commit 5993856).

Update my credits while at it.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

serverworks: add missing pci_dev_put() call

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

serverworks: cleanup svwks_udma_filter()

* remove dead OSB4 UDMA support
* remove unreachable code
* make isa_dev local to ->init_chipset

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

pdc202xx_old: add ->init_hwif method

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

opti621: remove stale driver history

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

cy82c693: remove stale driver history

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

cy82c693: fix PIO timings calculations

Just use the standard ide_timing_compute() helper to calculate
PIO timings.  This fixes many issues with the open-coded version
like using 16-bit timings when 8-bit ones should be used or not
accounting for the enhanced cycle time specified by the device.

Based on libata pata_cypress host driver.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

cmd64x: remove superfluous checks from cmd64x_set_dma_mode()

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

cmd64x: fix PIO and MWDMA timings calculations

Just use the standard ide_timing_compute() helper to calculate
PIO and MWDMA timings.  This fixes some issues with the open-coded
version like allowing faster MWDMA timings than the ones required
by the current PIO mode or not accounting for the enhanced MWDMA
cycle time specified by the device.

Based on libata pata_cmd64x host driver.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

amd74xx: don't change UDMA settings when programming PIO timings

Based on libata pata_amd host driver.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

alim15x3: cleanup ali_cable_detect()

Remove leftover local_irq_[save,restore]() and FIXME note.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

alim15x3: remove superfluous locking from ali_set_pio_mode()

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

alim15x3: add ali_fifo_control() helper

Based on libata pata_ali host driver.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

alim15x3: fix PIO timings calculations

Just use the standard ide_timing_compute() helper to calculate
PIO timings.  This fixes many issues with the open-coded version
like potential recovery timings underclocking or not accounting
for the enhanced cycle time specified by the device.

Based on libata pata_ali host driver.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ide: use standard timing for XFER_PIO_SLOW mode in ide_timing_compute()

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ide_tape: kill off use of the ->ioctl operation

Ready to get everything using unlocked_ioctl()

For ide_tape we just push down as this is legacy code anyway

Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Revert "x86, apic: Use logical flat on intel with <= 8 logical cpus"

Revert commit 2fbd07a5f5d1295fa9b0c0564ec27da7c276a75a, as this commit
breaks an IBM platform with quad-core Xeon cpu's.

According to Suresh, this might be an IBM platform issue, as on other
Intel platforms with <= 8 logical cpu's, logical flat mode works fine
irespective of physical apic id values (inline with the xapic
architecture).

Revert this for now because of the IBM platform breakage.

Another version will be re-submitted after the complete analysis.

Signed-off-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Acked-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Merge branch 'for-linus' of git://oss.sgi.com/xfs/xfs

* 'for-linus' of git://oss.sgi.com/xfs/xfs:
  xfs: Ensure we force all busy extents in range to disk
  xfs: Don't flush stale inodes
  xfs: fix timestamp handling in xfs_setattr
  xfs: use DECLARE_EVENT_CLASS

Merge git://git./linux/kernel/git/steve/gfs2-2.6-fixes

* git://git.kernel.org/pub/scm/linux/kernel/git/steve/gfs2-2.6-fixes:
  GFS2: Use MAX_LFS_FILESIZE for meta inode size
  GFS2: Fix gfs2_xattr_acl_chmod()
  GFS2: Fix locking bug in rename
  GFS2: Ensure uptodate inode size when using O_APPEND

Merge branch 'for_linus' of git://git./linux/kernel/git/jack/linux-fs-2.6

* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs-2.6:
  quota: Fix dquot_transfer for filesystems different from ext4

Merge branch 'agp-fixes' of git://git./linux/kernel/git/airlied/agp-2.6

* 'agp-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/agp-2.6:
  agp/hp: fail gracefully if we don't find an IOC
  agp/hp: fixup hp agp after ACPI changes
  agp: correct missing cleanup on error in agp_add_bridge

Merge branch 'drm-linus' of git://git./linux/kernel/git/airlied/drm-2.6

* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (45 commits)
  drm/nv04: Fix set_operation software method.
  drm/nouveau: initialise DMA tracking parameters earlier
  drm/nouveau: use dma.max rather than pushbuf size for checking GET validity
  drm/nv04: differentiate between nv04/nv05
  drm/nouveau: Fix null deref in nouveau_fence_emit due to deleted fence
  drm/nv50: prevent a possible ctxprog hang
  drm/nouveau: have ttm's fault handler called directly
  drm/nv50: restore correct cache1 get/put address on fifoctx load
  drm/nouveau: create function for "dealing" with gpu lockup
  drm/nouveau: remove unused nouveau_channel_idle() function
  drm/nouveau: fix handling of fbcon colours in 8bpp
  drm/nv04: Context switching fixes.
  drm/nouveau: Use the software object for fencing.
  drm/nouveau: Allocate a per-channel instance of NV_SW.
  drm/nv50: make the blocksize depend on vram size
  drm/nouveau: better alignment of bo sizes and use roundup instead of ALIGN
  drm/nouveau: Don't skip card take down on nv0x.
  drm/nouveau: Implement nv42-nv43 TV load detection.
  drm/nouveau: Clean up the nv17-nv4x load detection code a bit.
  drm/nv50: fix fillrect color
  ...

Merge branch 'hwmon-for-linus' of git://git./linux/kernel/git/jdelvare/staging

* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
  hwmon: Make PCI device ids constant
  hwmon: (coretemp) Fix TjMax for Atom N450/D410/D510 CPUs
  hwmon: (k10temp) Blacklist more family 10h processors
  hwmon: (asus_atk0110) Add debugfs interface
  hwmon: (asus_atk0110) Refactor interface probe code
  hwmon: (adt7462) Fix pin 28 monitoring

core, x86: make LIST_POISON less deadly

The list macros use LIST_POISON1 and LIST_POISON2 as undereferencable
pointers in order to trap erronous use of freed list_heads.  Unfortunately
userspace can arrange for those pointers to actually be dereferencable,
potentially turning an oops to an expolit.

To avoid this allow architectures (currently x86_64 only) to override
the default values for these pointers with truly-undereferencable values.
This is easy on x86_64 as the virtual address space is large and contains
areas that cannot be mapped.

Other 64-bit architectures will likely find similar unmapped ranges.

[ingo: switch to 0xdead000000000000 as the unmapped area]
[ingo: add comments, cleanup]
[jaswinder: eliminate sparse warnings]

Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Merge branch 'omap-fixes-for-linus' of git://git./linux/kernel/git/tmlind/linux-omap-2.6

* 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: (26 commits)
  OMAP2 clock: dynamically allocate CPUFreq frequency table
  OMAP clock/CPUFreq: add clk_exit_cpufreq_table()
  OMAP2xxx OPP: clean up comments in OPP data
  OMAP2xxx clock: clk2xxx.c doesn't compile if CPUFREQ is enabled
  OMAP1 clock: remove __initdata from struct clk_functions to prevent crash
  OMAP1 clock: Add missing clocks for OMAP 7xx
  OMAP clock: remove incorrect EXPORT_SYMBOL()s
  OMAP3 clock: Add capability to change rate of dpll4_m5_ck
  OMAP3 clock: McBSP 2, 3, 4 functional clock parent is PER_96M_FCLK, not CORE_96M_FCLK
  OMAP3: clock: add clockdomains for UART1 & 2
  OMAP2420 IO mapping: move IVA mapping virtual address out of vmalloc space
  OMAP2xxx IO mapping: mark DSP mappings as being 2420-only
  ARM: OMAP3: PM: Fix the Invalid CM_CLKSTCTRL reg access.
  OMAP2: remove duplicated #include
  omap3: EVM: Choose OMAP_PACKAGE_CBB
  omap3: Fix booting if package is uninitialized
  omap3: add missing parentheses
  omap3: add missing parentheses
  omap2/3: ZOOM: Correcting key mapping for few keys
  omap2/3: make serial_in_override() address the right uart port
  ...

mn10300: update the ASB2303 defconfig

Update the defconfig for the ASB2303 platform.

Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mn10300: make the ASB2305's PCnet32 NIC work by using the PCI bridge's SRAM

Access to the ASB2305's PCnet32 NIC doesn't work correctly because when
the NIC attempts to update the ring buffer flags by DMA, the change to RAM
crops up about 17uS after the interrupt line is asserted.  This is almost
certainly due to a bug in the PCI bridge FPGA on that board.

We can get around this by making dma_alloc_coherent() put the ring buffer
in the SRAM attached to the PCI bridge rather than in the SDRAM.

Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mn10300: insert PCI root bus resources for the ASB2305 devel motherboard

Insert PCI root bus resources for the MN10300-based ASB2305 development
kit motherboard.  This is required because the CPU's window onto the PCI
bus address space is considerably smaller than the CPU's full address
space and non-PCI devices lie outside of the PCI window that we might want
to access.

Without this patch, the PCI root bus uses the platform-level bus
resources, and these are then confined to the PCI window, thus making
platform_device_add() reject devices outside of this window.

We also add a reservation for the PCI SRAM region.

Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mn10300: use generic pci_enable_resources()

Use the generic pci_enable_resources() instead of the arch-specific code.

Unlike this arch-specific code, the generic version:

 - checks PCI_NUM_RESOURCES (11), not 6, resources
 - skips resources that have neither IORESOURCE_IO nor IORESOURCE_MEM set
 - skips ROM resources unless IORESOURCE_ROM_ENABLE is set
 - checks for resource collisions with "!r->parent"

Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mn10300: use KERN_ERR not KERN_ERROR

Use KERN_ERR not KERN_ERROR in the ASB2305 platform code.

Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mn10300: fix several bogus includes on abs2305

asm/cpu never existed for mn10300; the files they are looking for are in
asm.

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mn10300: wire up missing new syscalls

Wire up missing new system calls for MN10300.

Signed-off-by: David Howells <dhowelsl@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mn10300: add cc clobbers to asm statements

gcc 4.2.1 for MN10300 is more agressive than the older gcc in
reordering/moving other insns between an insn that sets flags and an insn
that uses those flags.  This leads to trouble with asm statements which
are missing an explicit "cc" clobber.  This patch adds the explicit "cc"
clobber to asm statements which do indeed clobber the condition flags.

Signed-off-by: Mark Salter <msalter@redhat.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mn10300: objcopy flags fix

The gcc-4.2.1 based toolchain for MN10300 adds some new note sections
which need to be stripped from the binary image.  This patch takes care of
that.

Signed-off-by: Mark Salter <msalter@redhat.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mn10300: signal stack fix

This fixes a signal stack handling problem in the MN10300 arch.  When new
threads are cloned with CLONE_VM, they don't inherit the alternate signal
stack.  They do share the signal flags, though.  When deciding whether to
use an alternate stack, the arch code needs to check to make sure the task
struct contains a valid alternate stack.  This patch fixes the MN10300
arch by using the sas_ss_flags() test provided by sched.h rather than the
on_sig_stack() test which is insufficient by itself.

Signed-off-by: Mark Salter <msalter@redhat.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

rtc_cmos: convert shutdown to new pnp_driver->shutdown

commit abd6633c67925f90775bb74755f9c547e30f1f20 ("pnp: add a shutdown
method to pnp drivers") adds shutdown method to bus driver blindly.  With
it, driver->shutdown is no longer valid.

Use pnp_driver->shutdown instead.

Addresses http://bugzilla.kernel.org/show_bug.cgi?id=14889

Signed-off-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Reported-by: Malte Schröder <maltesch@gmx.de>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: David Hardeman <david@hardeman.nu>
Cc: Dmitry Torokhov <dtor@mail.ru>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Paul Gortmaker <p_gortmaker@yahoo.com>
Cc: <stable@kernel.org> [2.6.32.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

smaps: fix wrong rss count

A long time ago we regarded zero page as file_rss and vm_normal_page
doesn't return NULL.

But now, we reinstated ZERO_PAGE and vm_normal_page's implementation can
return NULL in case of zero page.  Also we don't count it with file_rss
any more.

Then, RSS and PSS can't be matched.  For consistency, Let's ignore zero
page in smaps_pte_range.

Signed-off-by: Minchan Kim <minchan.kim@gmail.com>
Acked-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Acked-by: Hugh Dickins <hugh.dickins@tiscali.co.uk>
Acked-by: Matt Mackall <mpm@selenic.com>
Reviewed-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

documentation: update kernel-doc-nano-HOWTO information

Remove comments about function short descriptions not allowed to be on
multiple lines (that was fixed/changed recently).

Add comments that function "section header:" names need to be unique per
function/struct/union/typedef/enum.

Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

gpio: adp5588-gpio: new driver for ADP5588 GPIO expanders

Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drivers/cpuidle/governors/menu.c: fix undefined reference to `__udivdi3'

menu: use proper 64 bit math

The new menu governor is incorrectly doing a 64 bit divide.  Compile
tested only

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Len Brown <len.brown@intel.com>
Cc: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Documentation: update ring-buffer-design.txt

Fix typos, grammos, spellos, hyphenation.

Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Cc: Mel Gorman <mel@csn.ul.ie>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm: hugetlb: fix clear_huge_page()

sz is in bytes, MAX_ORDER_NR_PAGES is in pages.

Signed-off-by: Andrea Arcangeli <aarcange@redhat.com>
Acked-by: David Gibson <dwg@au1.ibm.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: David Rientjes <rientjes@google.com>
Cc: Lee Schermerhorn <lee.schermerhorn@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

hwmon: driver for Texas Instruments amc6821 chip

Signed-off-by: <tomaz.mertelj@guest.arnes.si>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

gpiolib: fix poll(2) support reconfigure on sysfs polarity change

Previously enabled poll(2) support on one edge was never reconfigured when
sysfs polarity change was triggered from kernel, because 'struct device
*dev' shadowed an earlier definition.

Found by sparse, which I should've run much earlier.

Signed-off-by: Jani Nikula <ext-jani.1.nikula@nokia.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

vsnprintf: fix reference for compressed ipv6 addresses

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reported-by: Josip Rodin <joy@entuzijast.net>
Cc: Joe Perches <joe@perches.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mmc: allow for MMC v4.4

JEDEC eMMC specification version 4.4 (MMCA 4.4) defines Extended CSD
structure versions up to 5.

Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mmc_block: fix queue cleanup

The main bug was that 'blk_cleanup_queue()' was called while the block
device could still be in use, for example, because the card was removed
while files were still open.

In addition, to be sure that 'mmc_request()' will get called for all new
requests (so it can error them out), the queue is emptied during cleanup.
This is done after the worker thread is stopped to avoid racing with it.

Finally, it is not a device error for this to be happening, so quiet the
(sometimes very many) error messages.

Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Cc: <linux-mmc@vger.kernel.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mmc_block: fix probe error cleanup bug

If mmc_blk_set_blksize() fails mmc_blk_probe() the request queue and its
thread have been set up and they need to be shut down properly before
putting the disk.

Signed-off-by: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Cc: <linux-mmc@vger.kernel.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mmc_block: add dev_t initialization check

When a card is removed before mmc_blk_probe() has called add_disk(), then
the minor field is uninitialized and has value 0.  This caused
mmc_blk_put() to always release devidx 0 even if 0 was still in use.  Then
the next mmc_blk_probe() used the first free idx of 0, which oopses in
sysfs, since it is used by another card.

Signed-off-by: Anna Lemehova <EXT-Anna.Lemehova@nokia.com>
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Cc: <linux-mmc@vger.kernel.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

power: fix kernel-doc notation

Warning(drivers/base/power/main.c:453): No description found for parameter 'dev'
Warning(drivers/base/power/main.c:453): No description found for parameter 'cb'
Warning(drivers/base/power/main.c:719): No description found for parameter 'dev'
Warning(drivers/base/power/main.c:719): No description found for parameter 'state'
Warning(drivers/base/power/main.c:719): No description found for parameter 'cb'

Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

proc: partially revert "procfs: provide stack information for threads"

Commit d899bf7b (procfs: provide stack information for threads) introduced
to show stack information in /proc/{pid}/status.  But it cause large
performance regression.  Unfortunately /proc/{pid}/status is used ps
command too and ps is one of most important component.  Because both to
take mmap_sem and page table walk are heavily operation.

If many process run, the ps performance is,

[before d899bf7b]

% perf stat ps >/dev/null

 Performance counter stats for 'ps':

     4090.435806  task-clock-msecs         #      0.032 CPUs
             229  context-switches         #      0.000 M/sec
               0  CPU-migrations           #      0.000 M/sec
             234  page-faults              #      0.000 M/sec
      8587565207  cycles                   #   2099.425 M/sec
      9866662403  instructions             #      1.149 IPC
      3789415411  cache-references         #    926.409 M/sec
        30419509  cache-misses             #      7.437 M/sec

   128.859521955  seconds time elapsed

[after d899bf7b]

% perf stat  ps  > /dev/null

 Performance counter stats for 'ps':

     4305.081146  task-clock-msecs         #      0.028 CPUs
             480  context-switches         #      0.000 M/sec
               2  CPU-migrations           #      0.000 M/sec
             237  page-faults              #      0.000 M/sec
      9021211334  cycles                   #   2095.480 M/sec
     10605887536  instructions             #      1.176 IPC
      3612650999  cache-references         #    839.160 M/sec
        23917502  cache-misses             #      5.556 M/sec

   152.277819582  seconds time elapsed

Thus, this patch revert it. Fortunately /proc/{pid}/task/{tid}/smaps
provide almost same information. we can use it.

Commit d899bf7b introduced two features:

 1) Add the annotattion of [thread stack: xxxx] mark to
    /proc/{pid}/task/{tid}/maps.
 2) Add StackUsage field to /proc/{pid}/status.

I only revert (2), because I haven't seen (1) cause regression.

Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Stefani Seibold <stefani@seibold.net>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andi Kleen <andi@firstfloor.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

.gitignore: ignore vmlinuz

MIPS compressed kernels output a vmlinuz file in the top-level directory
(maybe others do).  Add vmlinuz to the list of files to ignore by git.

Signed-off-by: Florian Fainelli <ffainelli@freebox.fr>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Maxime Bizon <mbizon@freebox.fr>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

kernel/signal.c: fix kernel information leak with print-fatal-signals=1

When print-fatal-signals is enabled it's possible to dump any memory
reachable by the kernel to the log by simply jumping to that address from
user space.

Or crash the system if there's some hardware with read side effects.

The fatal signals handler will dump 16 bytes at the execution address,
which is fully controlled by ring 3.

In addition when something jumps to a unmapped address there will be up to
16 additional useless page faults, which might be potentially slow (and at
least is not very efficient)

Fortunately this option is off by default and only there on i386.

But fix it by checking for kernel addresses and also stopping when there's
a page fault.

Signed-off-by: Andi Kleen <ak@linux.intel.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

cgroups: fix 2.6.32 regression causing BUG_ON() in cgroup_diput()

The LTP cgroup test suite generates a "kernel BUG at kernel/cgroup.c:790!"
here in cgroup_diput():

                 /*
                  * if we're getting rid of the cgroup, refcount should ensure
                  * that there are no pidlists left.
                  */
                 BUG_ON(!list_empty(&cgrp->pidlists));

The cgroup pidlist rework in 2.6.32 generates the BUG_ON, which is caused
when pidlist_array_load() calls cgroup_pidlist_find():

(1) if a matching cgroup_pidlist is found, it down_write's the mutex of the
     pre-existing cgroup_pidlist, and increments its use_count.
(2) if no matching cgroup_pidlist is found, then a new one is allocated, it
     down_write's its mutex, and the use_count is set to 0.
(3) the matching, or new, cgroup_pidlist gets returned back to pidlist_array_load(),
     which increments its use_count -- regardless whether new or pre-existing --
     and up_write's the mutex.

So if a matching list is ever encountered by cgroup_pidlist_find() during
the life of a cgroup directory, it results in an inflated use_count value,
preventing it from ever getting released by cgroup_release_pid_array().
Then if the directory is subsequently removed, cgroup_diput() hits the
BUG_ON() when it finds that the directory's cgroup is still populated with
a pidlist.

The patch simply removes the use_count increment when a matching pidlist
is found by cgroup_pidlist_find(), because it gets bumped by the calling
pidlist_array_load() function while still protected by the list's mutex.

Signed-off-by: Dave Anderson <anderson@redhat.com>
Reviewed-by: Li Zefan <lizf@cn.fujitsu.com>
Acked-by: Ben Blum <bblum@andrew.cmu.edu>
Cc: Paul Menage <menage@google.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

scripts/get_maintainer.pl: fix file exclusion X: logic

The following command doesn't generate any output.
`./scripts/get_maintainer.pl --no-git -f drivers/net/wireless/wl12xx/wl1271_acx.c`

An excluded "X:" pattern match in any section would cause a file not to
match any other section.

Signed-off-by: Joe Perches <joe@perches.com>
Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

lib/rational.c needs module.h

lib/rational.c:62: warning: data definition has no type or storage class
lib/rational.c:62: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL'
lib/rational.c:62: warning: parameter names (without types) in function declaration

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: WANG Cong <xiyou.wangcong@gmail.com>
Cc: Oskar Schirmer <os@emlix.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Add LZO compression support for initramfs and old-style initrd

Signed-off-by: Albin Tonnerre <albin.tonnerre@free-electrons.com>
Tested-by: Wu Zhangjin <wuzhangjin@gmail.com>
Acked-by: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Russell King <rmk@arm.linux.org.uk>
Acked-by: Russell King <rmk@arm.linux.org.uk>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

x86: add support for LZO-compressed kernels

The necessary changes to the x86 Kconfig and boot/compressed to allow the
use of this new compression method

Signed-off-by: Albin Tonnerre <albin.tonnerre@free-electrons.com>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Tested-by: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Russell King <rmk@arm.linux.org.uk>
Acked-by: Russell King <rmk@arm.linux.org.uk>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

arm: add support for LZO-compressed kernels

- changes to ach/arch/boot/Makefile to make it easier to add new
   compression types
 - new piggy.lzo.S necessary for lzo compression
 - changes in arch/arm/boot/compressed/misc.c to allow the use of lzo or
   gzip, depending on the config
 - Kconfig support

Signed-off-by: Albin Tonnerre <albin.tonnerre@free-electrons.com>
Tested-by: Wu Zhangjin <wuzhangjin@gmail.com>
Acked-by: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Russell King <rmk@arm.linux.org.uk>
Acked-by: Russell King <rmk@arm.linux.org.uk>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

lib: add support for LZO-compressed kernels

This patch series adds generic support for creating and extracting
LZO-compressed kernel images, as well as support for using such images on
the x86 and ARM architectures, and support for creating and using
LZO-compressed initrd and initramfs images.

Russell King said:

: Testing on a Cortex A9 model:
: - lzo decompressor is 65% of the time gzip takes to decompress a kernel
: - lzo kernel is 9% larger than a gzip kernel
:
: which I'm happy to say confirms your figures when comparing the two.
:
: However, when comparing your new gzip code to the old gzip code:
: - new is 99% of the size of the old code
: - new takes 42% of the time to decompress than the old code
:
: What this means is that for a proper comparison, the results get even better:
: - lzo is 7.5% larger than the old gzip'd kernel image
: - lzo takes 28% of the time that the old gzip code took
:
: So the expense seems definitely worth the effort.  The only reason I
: can think of ever using gzip would be if you needed the additional
: compression (eg, because you have limited flash to store the image.)
:
: I would argue that the default for ARM should therefore be LZO.

This patch:

The lzo compressor is worse than gzip at compression, but faster at
extraction.  Here are some figures for an ARM board I'm working on:

Uncompressed size: 3.24Mo
gzip  1.61Mo 0.72s
lzo   1.75Mo 0.48s

So for a compression ratio that is still relatively close to gzip, it's
much faster to extract, at least in that case.

This part contains:
 - Makefile routine to support lzo compression
 - Fixes to the existing lzo compressor so that it can be used in
   compressed kernels
 - wrapper around the existing lzo1x_decompress, as it only extracts one
   block at a time, while we need to extract a whole file here
 - config dialog for kernel compression

[akpm@linux-foundation.org: coding-style fixes]
[akpm@linux-foundation.org: cleanup]
Signed-off-by: Albin Tonnerre <albin.tonnerre@free-electrons.com>
Tested-by: Wu Zhangjin <wuzhangjin@gmail.com>
Acked-by: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Russell King <rmk@arm.linux.org.uk>
Acked-by: Russell King <rmk@arm.linux.org.uk>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

zlib: optimize inffast when copying direct from output

JFFS2 uses lesser compression ratio and inflate always ends up in "copy
direct from output" case.

This patch tries to optimize the direct copy procedure.  Uses
get_unaligned() but only in one place.

The copy loop just above this one can also use this optimization, but I
havn't done so as I have not tested if it is a win there too.

On my MPC8321 this is about 17% faster on my JFFS2 root FS than the
original.

[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Cc: Roel Kluin <roel.kluin@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

percpu: avoid calling __pcpu_ptr_to_addr(NULL)

__pcpu_ptr_to_addr() can be overridden by the architecture and might not
behave well if passed a NULL pointer.  So avoid calling it until we have
verified that its arg is not NULL.

Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Kamalesh Babulal <kamalesh@linux.vnet.ibm.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

kmod: fix resource leak in call_usermodehelper_pipe()

Fix resource (write-pipe file) leak in call_usermodehelper_pipe().

When call_usermodehelper_exec() fails, write-pipe file is opened and
call_usermodehelper_pipe() just returns an error.  Since it is hard for
caller to determine whether the error occured when opening the pipe or
executing the helper, the caller cannot close the pipe by themselves.

I've found this resoruce leak when testing coredump.  You can check how
the resource leaks as below;

$ echo "|nocommand" > /proc/sys/kernel/core_pattern
$ ulimit -c unlimited
$ while [ 1 ]; do ./segv; done &> /dev/null &
$ cat /proc/meminfo (<- repeat it)

where segv.c is;
//-----
int main () {
        char *p = 0;
        *p = 1;
}
//-----

This patch closes write-pipe file if call_usermodehelper_exec() failed.

Signed-off-by: Masami Hiramatsu <mhiramat@redhat.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

dma-debug: allow DMA_BIDIRECTIONAL mappings to be synced with DMA_FROM_DEVICE and

There is no need to perform full BIDIR sync (copying the buffers in case
of swiotlb and similar schemes) if we know that the owner (CPU or device)
hasn't altered the data.

Addresses the false-positive reported at
http://bugzilla.kernel.org/show_bug.cgi?id=14169

Signed-off-by: Krzysztof Halasa <khc@pm.waw.pl>
Cc: David Miller <davem@davemloft.net>
Cc: Joerg Roedel <joerg.roedel@amd.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

kmemcheck: make bitfield annotations truly no-ops when disabled

It turns out that even zero-sized struct members (int foo[0];) will affect
the struct layout, causing us in particular to lose 4 bytes in struct
sock.

This patch fixes the regression in CONFIG_KMEMCHECK=n case.

Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Vegard Nossum <vegard.nossum@gmail.com>
Acked-by: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

docs: large update to ioctl-number.txt

Add many ioctl definitions to ioctl-number.txt.
Fix some whitespace/formatting.
Correct some filenames/paths.

Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm: make totalhigh_pages unsigned long

Makes it consistent with the extern declaration, used when CONFIG_HIGHMEM
is set Removes redundant casts in printout messages

Signed-off-by: Andreas Fenkart <andreas.fenkart@streamunlimited.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: David Howells <dhowells@redhat.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Chen Liqin <liqin.chen@sunplusct.com>
Cc: Lennox Wu <lennox.wu@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

quota: Fix dquot_transfer for filesystems different from ext4

Commit fd8fbfc1 modified the way we find amount of reserved space
belonging to an inode. The amount of reserved space is checked
from dquot_transfer and thus inode_reserved_space gets called
even for filesystems that don't provide get_reserved_space callback
which results in a BUG.

Fix the problem by checking get_reserved_space callback and return 0 if
the filesystem does not provide it.

CC: Dmitry Monakhov <dmonakhov@openvz.org>
Signed-off-by: Jan Kara <jack@suse.cz>

GFS2: Use MAX_LFS_FILESIZE for meta inode size

Using ~0ULL was cauing sign issues in filemap_fdatawrite_range, so
use MAX_LFS_FILESIZE instead.

Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>

agp/hp: fail gracefully if we don't find an IOC

Bail out if we don't find an enclosing IOC.  Previously, if we didn't
find one, we tried to set things up using garbage for the SBA/IOC register
address, which causes a crash.

This crash only happens if firmware supplies a defective ACPI namespace, so
it doesn't fix any problems in the field.

Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

agp/hp: fixup hp agp after ACPI changes

Commit 15b8dd53f5ffa changed the string in info->hardware_id from a static
array to a pointer and added a length field.  But instead of changing
"sizeof(array)" to "length", we changed it to "sizeof(length)" (== 4),
which corrupts the string we're trying to null-terminate.

We no longer even need to null-terminate the string, but we *do* need to
check whether we found a HID.  If there's no HID, we used to have an empty
array, but now we have a null pointer.

The combination of these defects causes this oops:

  Unable to handle kernel NULL pointer dereference (address 0000000000000003)
  modprobe[895]: Oops 8804682956800 [1]
  ip is at zx1_gart_probe+0xd0/0xcc0 [hp_agp]

  http://marc.info/?l=linux-ia64&m=126264484923647&w=2

Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Reported-by: Émeric Maschino <emeric.maschino@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

agp: correct missing cleanup on error in agp_add_bridge

While investigating a kmemleak detected leak, I encountered the
agp_add_bridge function.  It appears to be responsible for freeing
the agp_bridge_data in the case of a failure, but it is only doing
so for some errors.

Fix it to always free the bridge data if a failure condition is
encountered.

Signed-off-by: Kevin Winchester <kjwinchester@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>

Merge branch 'for-airlied' of /ssd/git/drm-nouveau-next into drm-linus

* 'for-airlied' of /ssd/git/drm-nouveau-next: (28 commits)
  drm/nv04: Fix set_operation software method.
  drm/nouveau: initialise DMA tracking parameters earlier
  drm/nouveau: use dma.max rather than pushbuf size for checking GET validity
  drm/nv04: differentiate between nv04/nv05
  drm/nouveau: Fix null deref in nouveau_fence_emit due to deleted fence
  drm/nv50: prevent a possible ctxprog hang
  drm/nouveau: have ttm's fault handler called directly
  drm/nv50: restore correct cache1 get/put address on fifoctx load
  drm/nouveau: create function for "dealing" with gpu lockup
  drm/nouveau: remove unused nouveau_channel_idle() function
  drm/nouveau: fix handling of fbcon colours in 8bpp
  drm/nv04: Context switching fixes.
  drm/nouveau: Use the software object for fencing.
  drm/nouveau: Allocate a per-channel instance of NV_SW.
  drm/nv50: make the blocksize depend on vram size
  drm/nouveau: better alignment of bo sizes and use roundup instead of ALIGN
  drm/nouveau: Don't skip card take down on nv0x.
  drm/nouveau: Implement nv42-nv43 TV load detection.
  drm/nouveau: Clean up the nv17-nv4x load detection code a bit.
  drm/nv50: fix fillrect color
  ...

Merge remote branch 'korg/drm-radeon-next' into drm-linus

* korg/drm-radeon-next:
  drm/radeon/kms: add additional safe regs for r4xx/rs6xx and r5xx
  drm/radeon/kms: Don't try to enable IRQ if we have no handler installed
  drm: Avoid calling vblank function is vblank wasn't initialized
  drm/radeon: mkregtable.c: close a file before exit
  drm/radeon/kms: Make sure we release AGP device if we acquired it
  drm/radeon/kms: Schedule host path read cache flush through the ring V2
  drm/radeon/kms: Workaround RV410/R420 CP errata (V3)
  drm/radeon/kms: detect sideport memory on IGP chips
  drm/radeon: fix a couple of array index errors
  drm/radeon/kms: add support for eDP (embedded DisplayPort)
  drm: Add eDP connector type
  drm/radeon/kms: pull in the latest upstream ObjectID.h changes
  drm/radeon/kms: whitespace changes to ObjectID.h
  drm/radeon/kms: fix typo in atom connector type handling