pinctrl: intel: fix unexpected interrupt

commit e986f0e602f19ecb7880b04dd1db415ed9bca3f6 upstream.

ASUS Chromebook C223 with Celeron N3350 crashes sometimes during
cold booot. Inspection of the kernel log showed that it gets into
an inifite loop logging the following message:

->handle_irq():  000000009cdb51e8, handle_bad_irq+0x0/0x251
->irq_data.chip(): 000000005ec212a7, 0xffffa043009d8e7
->action(): 00000
   IRQ_NOPROBE set
unexpected IRQ trap at vector 7c

The issue happens during cold boot but only if cold boot happens
at most several dozen seconds after Chromebook is powered off. For
longer intervals between power off and power on (cold boot) the issue
does not reproduce. The unexpected interrupt is sourced from INT3452
GPIO pin which is used for SD card detect. Investigation relevealed
that when the interval between power off and power on (cold boot)
is less than several dozen seconds then values of INT3452 GPIO interrupt
enable and interrupt pending registers survive power off and power
on sequence and interrupt for SD card detect pin is enabled and pending
during probe of SD controller which causes the unexpected IRQ message.
"Intel Pentium and Celeron Processor N- and J- Series" volume 3 doc
mentions that GPIO interrupt enable and status registers default
value is 0x0.
The fix clears INT3452 GPIO interrupt enabled and interrupt pending
registers in its probe function.

Fixes: 7981c0015af2 ("pinctrl: intel: Add Intel Sunrisepoint pin controller and GPIO support")
Signed-off-by: Łukasz Bartosik <lb@semihalf.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

pinctrl: intel: Fix a glitch when updating IRQ flags on a preconfigured line

commit e12963c453263d5321a2c610e98cbc731233b685 upstream.

The commit af7e3eeb84e2 ("pinctrl: intel: Disable input and output buffer
when switching to GPIO") hadn't taken into account an update of the IRQ
flags scenario.

When updating the IRQ flags on the preconfigured line the ->irq_set_type()
is called again. In such case the sequential Rx buffer configuration
changes may trigger a falling or rising edge interrupt that may lead,
on some platforms, to an undesired event.

This may happen because each of intel_gpio_set_gpio_mode() and
__intel_gpio_set_direction() updates the pad configuration with a different
value of the GPIORXDIS bit. Notable, that the intel_gpio_set_gpio_mode() is
called only for the pads that are configured as an input. Due to this fact,
integrate the logic of __intel_gpio_set_direction() call into the
intel_gpio_set_gpio_mode() so that the Rx buffer won't be disabled and
immediately re-enabled.

Fixes: af7e3eeb84e2 ("pinctrl: intel: Disable input and output buffer when switching to GPIO")
Reported-by: Kane Chen <kane.chen@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Grace Kao <grace.kao@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

pinctrl: sunxi: Fix H616 I2S3 pin data

commit 1fd6bb5b47a65eacb063b37e6fa6df2b8fa92959 upstream.

Two bugs have sneaked in the H616 pinctrl data:
- PH9 uses the mux value of 0x3 twice (one should be 0x5 instead)
- PH8 and PH9 use the "i2s3" function name twice in each pin

For the double pin name we use the same trick we pulled for i2s0: append
the pin function to the group name to designate the special function.

Fixes: 25adc29407fb ("pinctrl: sunxi: Add support for the Allwinner H616 pin controller")
Reported-by: SASANO Takayoshi <uaa@mx5.nisiq.net>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Link: https://lore.kernel.org/r/20220105172952.23347-1-andre.przywara@arm.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ASoC: codecs: wcd938x: fix return value of mixer put function

commit bd2347fd67d8da0fa76296507cc556da0a233bcb upstream.

wcd938x_ear_pa_put_gain, wcd938x_set_swr_port and  wcd938x_set_compander
currently returns zero eventhough it changes the value.
Fix this, so that change notifications are sent correctly.

Fixes: e8ba1e05bdc01 ("ASoC: codecs: wcd938x: add basic controls")
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20220126113549.8853-4-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ASoC: codecs: lpass-rx-macro: fix sidetone register offsets

commit fca041a3ab70a099a6d5519ecb689b6279bd04f3 upstream.

For some reason we ended up with incorrect register offfset calcuations
for sidetone. regmap clearly throw errors when accessing these incorrect
registers as these do not belong to any read/write ranges.
so fix them to point to correct register offsets.

Fixes: f3ce6f3c9a99 ("ASoC: codecs: lpass-rx-macro: add iir widgets")
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20220126113549.8853-3-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ASoC: codecs: wcd938x: fix incorrect used of portid

commit c5c1546a654f613e291a7c5d6f3660fc1eb6d0c7 upstream.

Mixer controls have the channel id in mixer->reg, which is not same
as port id. port id should be derived from chan_info array.
So fix this. Without this, its possible that we could corrupt
struct wcd938x_sdw_priv by accessing port_map array out of range
with channel id instead of port id.

Fixes: e8ba1e05bdc0 ("ASoC: codecs: wcd938x: add basic controls")
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20220126113549.8853-2-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ASoC: max9759: fix underflow in speaker_gain_control_put()

commit 4c907bcd9dcd233da6707059d777ab389dcbd964 upstream.

Check for negative values of "priv->gain" to prevent an out of bounds
access.  The concern is that these might come from the user via:
  -> snd_ctl_elem_write_user()
    -> snd_ctl_elem_write()
      -> kctl->put()

Fixes: fa8d915172b8 ("ASoC: max9759: Add Amplifier Driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20220119123101.GA9509@kili
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ASoC: cpcap: Check for NULL pointer after calling of_get_child_by_name

commit f7a6021aaf02088870559f82fc13c58cda7fea1a upstream.

If the device does not exist, of_get_child_by_name() will return NULL
pointer.
And devm_snd_soc_register_component() does not check it.
Also, I have noticed that cpcap_codec_driver has not been used yet.
Therefore, it should be better to check it in order to avoid the future
dereference of the NULL pointer.

Fixes: f6cdf2d3445d ("ASoC: cpcap: new codec")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Link: https://lore.kernel.org/r/20220111025048.524134-1-jiasheng@iscas.ac.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ASoC: simple-card: fix probe failure on platform component

commit a64067f4cecaaa4deed8e33d3266bc0bcc189142 upstream.

A previous change to simple-card resulted in asoc_simple_parse_dai
attempting to retrieve the dai_name for platform components, which are
unlikely to have a valid DAI name. This caused simple-card to fail to
probe when using the xlnx_formatter_pcm as the platform component, since
it does not register any DAI components.

Since the dai_name is not used for platform components, just skip trying
to retrieve it for those.

Fixes: f107294c6422 ("ASoC: simple-card: support snd_soc_dai_link_component style for cpu")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Link: https://lore.kernel.org/r/20220107214711.1100162-6-robert.hancock@calian.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ASoC: xilinx: xlnx_formatter_pcm: Make buffer bytes multiple of period bytes

commit e958b5884725dac86d36c1e7afe5a55f31feb0b2 upstream.

This patch is based on one in the Xilinx kernel tree, "ASoc: xlnx: Make
buffer bytes multiple of period bytes" by Devarsh Thakkar. The same
issue exists in the mainline version of the driver. The original
patch description is as follows:

"The Xilinx Audio Formatter IP has a constraint on period
bytes to be multiple of 64. This leads to driver changing
the period size to suitable frames such that period bytes
are multiple of 64.

Now since period bytes and period size are updated but not
the buffer bytes, this may make the buffer bytes unaligned
and not multiple of period bytes.

When this happens we hear popping noise as while DMA is being
done the buffer bytes are not enough to complete DMA access
for last period of frame within the application buffer boundary.

To avoid this, align buffer bytes too as multiple of 64, and
set another constraint to always enforce number of periods as
integer. Now since, there is already a rule in alsa core
to enforce Buffer size = Number of Periods * Period Size
this automatically aligns buffer bytes as multiple of period
bytes."

Fixes: 6f6c3c36f091 ("ASoC: xlnx: add pcm formatter platform driver")
Cc: Devarsh Thakkar <devarsh.thakkar@xilinx.com>
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Link: https://lore.kernel.org/r/20220107214711.1100162-2-robert.hancock@calian.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ASoC: fsl: Add missing error handling in pcm030_fabric_probe

commit fb25621da5702c104ce0a48de5b174ced09e5b4e upstream.

Add the missing platform_device_put() and platform_device_del()
before return from pcm030_fabric_probe in the error handling case.

Fixes: c912fa913446 ("ASoC: fsl: register the wm9712-codec")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Link: https://lore.kernel.org/r/20220127131336.30214-1-linmq006@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/amd: avoid suspend on dGPUs w/ s2idle support when runtime PM enabled

commit e55a3aea418269266d84f426b3bd70794d3389c8 upstream.

dGPUs connected to Intel systems configured for suspend to idle
will not have the power rails cut at suspend and resetting the GPU
may lead to problematic behaviors.

Fixes: e25443d2765f4 ("drm/amdgpu: add a dev_pm_ops prepare callback (v2)")
Link: https://gitlab.freedesktop.org/drm/amd/-/issues/1879
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/i915/overlay: Prevent divide by zero bugs in scaling

commit 90a3d22ff02b196d5884e111f39271a1d4ee8e3e upstream.

Smatch detected a divide by zero bug in check_overlay_scaling().

    drivers/gpu/drm/i915/display/intel_overlay.c:976 check_overlay_scaling()
    error: potential divide by zero bug '/ rec->dst_height'.
    drivers/gpu/drm/i915/display/intel_overlay.c:980 check_overlay_scaling()
    error: potential divide by zero bug '/ rec->dst_width'.

Prevent this by ensuring that the dst height and width are non-zero.

Fixes: 02e792fbaadb ("drm/i915: implement drmmode overlay support v4")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220124122409.GA31673@kili
(cherry picked from commit cf5b64f7f10b28bebb9b7c9d25e7aee5cbe43918)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/kmb: Fix for build errors with Warray-bounds

commit 43f2517955875be5d96b641fba33d73097fe3cd9 upstream.

This fixes the following build error

drivers/gpu/drm/kmb/kmb_plane.c: In function 'kmb_plane_atomic_disable':
drivers/gpu/drm/kmb/kmb_plane.c:165:34: error: array subscript 3 is above array bounds of 'struct layer_status[2]' [-Werror=array-bounds]
  165 |                 kmb->plane_status[plane_id].ctrl =
  LCD_CTRL_GL2_ENABLE;
  |                 ~~~~~~~~~~~~~~~~~^~~~~~~~~~
  In file included from drivers/gpu/drm/kmb/kmb_plane.c:17:
  drivers/gpu/drm/kmb/kmb_drv.h:61:41: note: while referencing 'plane_status'
  61 |         struct layer_status  plane_status[KMB_MAX_PLANES];
  |                                         ^~~~~~~~~~~~
  drivers/gpu/drm/kmb/kmb_plane.c:162:34: error: array subscript 2 is above array bounds of 'struct layer_status[2]' [-Werror=array-bounds]
  162 |  kmb->plane_status[plane_id].ctrl =  LCD_CTRL_GL1_ENABLE;
  |                 ~~~~~~~~~~~~~~~~~^~~~~~~~~~
  In file included from
  drivers/gpu/drm/kmb/kmb_plane.c:17:
  drivers/gpu/drm/kmb/kmb_drv.h:61:41: note: while referencing 'plane_status'
  61 |         struct layer_status  plane_status[KMB_MAX_PLANES];
  |
  ^~~~~~~~~~~~

Fixes: 7f7b96a8a0a1 ("drm/kmb: Add support for KeemBay Display")
Signed-off-by: Anitha Chrisanthus <anitha.chrisanthus@intel.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220127194227.2213608-1-anitha.chrisanthus@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: stmmac: ensure PTP time register reads are consistent

commit 80d4609008e6d696a279e39ae7458c916fcd44c1 upstream.

Even if protected from preemption and interrupts, a small time window
remains when the 2 register reads could return inconsistent values,
each time the "seconds" register changes. This could lead to an about
1-second error in the reported time.

Add logic to ensure the "seconds" and "nanoseconds" values are consistent.

Fixes: 92ba6888510c ("stmmac: add the support for PTP hw clock driver")
Signed-off-by: Yannick Vignon <yannick.vignon@nxp.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20220203160025.750632-1-yannick.vignon@oss.nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: stmmac: dump gmac4 DMA registers correctly

commit 7af037c39b600bac2c716dd1228e8ddbe149573f upstream.

Unlike gmac100, gmac1000, gmac4 has 27 DMA registers and they are
located at DMA_CHAN_BASE_ADDR (0x1100). In order for ethtool to dump
gmac4 DMA registers correctly, this commit checks if a net_device has
gmac4 and uses different logic to dump its DMA registers.

This fixes the following KASAN warning, which can normally be triggered
by a command similar like "ethtool -d eth0":

BUG: KASAN: vmalloc-out-of-bounds in dwmac4_dump_dma_regs+0x6d4/0xb30
Write of size 4 at addr ffffffc010177100 by task ethtool/1839
 kasan_report+0x200/0x21c
 __asan_report_store4_noabort+0x34/0x60
 dwmac4_dump_dma_regs+0x6d4/0xb30
 stmmac_ethtool_gregs+0x110/0x204
 ethtool_get_regs+0x200/0x4b0
 dev_ethtool+0x1dac/0x3800
 dev_ioctl+0x7c0/0xb50
 sock_ioctl+0x298/0x6c4
 ...

Fixes: fbf68229ffe7 ("net: stmmac: unify registers dumps methods")
Signed-off-by: Camel Guo <camelg@axis.com>
Link: https://lore.kernel.org/r/20220131083841.3346801-1-camel.guo@axis.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: macsec: Verify that send_sci is on when setting Tx sci explicitly

commit d0cfa548dbde354de986911d3913897b5448faad upstream.

When setting Tx sci explicit, the Rx side is expected to use this
sci and not recalculate it from the packet.However, in case of Tx sci
is explicit and send_sci is off, the receiver is wrongly recalculate
the sci from the source MAC address which most likely be different
than the explicit sci.

Fix by preventing such configuration when macsec newlink is established
and return EINVAL error code on such cases.

Fixes: c09440f7dcb3 ("macsec: introduce IEEE 802.1AE driver")
Signed-off-by: Lior Nahmanson <liorna@nvidia.com>
Reviewed-by: Raed Salem <raeds@nvidia.com>
Signed-off-by: Raed Salem <raeds@nvidia.com>
Link: https://lore.kernel.org/r/1643542672-29403-1-git-send-email-raeds@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: macsec: Fix offload support for NETDEV_UNREGISTER event

commit 9cef24c8b76c1f6effe499d2f131807c90f7ce9a upstream.

Current macsec netdev notify handler handles NETDEV_UNREGISTER event by
releasing relevant SW resources only, this causes resources leak in case
of macsec HW offload, as the underlay driver was not notified to clean
it's macsec offload resources.

Fix by calling the underlay driver to clean it's relevant resources
by moving offload handling from macsec_dellink() to macsec_common_dellink()
when handling NETDEV_UNREGISTER event.

Fixes: 3cf3227a21d1 ("net: macsec: hardware offloading infrastructure")
Signed-off-by: Lior Nahmanson <liorna@nvidia.com>
Reviewed-by: Raed Salem <raeds@nvidia.com>
Signed-off-by: Raed Salem <raeds@nvidia.com>
Reviewed-by: Antoine Tenart <atenart@kernel.org>
Link: https://lore.kernel.org/r/1643542141-28956-1-git-send-email-raeds@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: stmmac: properly handle with runtime pm in stmmac_dvr_remove()

commit 6449520391dfc3d2cef134f11a91251a054ff7d0 upstream.

There are two issues with runtime pm handling in stmmac_dvr_remove():

1. the mac is runtime suspended before stopping dma and rx/tx. We
need to ensure the device is properly resumed back.

2. the stmmaceth clk enable/disable isn't balanced in both exit and
error handling code path. Take the exit code path for example, when we
unbind the driver or rmmod the driver module, the mac is runtime
suspended as said above, so the stmmaceth clk is disabled, but
stmmac_dvr_remove()
  stmmac_remove_config_dt()
    clk_disable_unprepare()
CCF will complain this time. The error handling code path suffers
from the similar situtaion.

Here are kernel warnings in error handling code path on Allwinner D1
platform:

[    1.604695] ------------[ cut here ]------------
[    1.609328] bus-emac already disabled
[    1.613015] WARNING: CPU: 0 PID: 38 at drivers/clk/clk.c:952 clk_core_disable+0xcc/0xec
[    1.621039] CPU: 0 PID: 38 Comm: kworker/u2:1 Not tainted 5.14.0-rc4#1
[    1.627653] Hardware name: Allwinner D1 NeZha (DT)
[    1.632443] Workqueue: events_unbound deferred_probe_work_func
[    1.638286] epc : clk_core_disable+0xcc/0xec
[    1.642561]  ra : clk_core_disable+0xcc/0xec
[    1.646835] epc : ffffffff8023c2ec ra : ffffffff8023c2ec sp : ffffffd00411bb10
[    1.654054]  gp : ffffffff80ec9988 tp : ffffffe00143a800 t0 : ffffffff80ed6a6f
[    1.661272]  t1 : ffffffff80ed6a60 t2 : 0000000000000000 s0 : ffffffe001509e00
[    1.668489]  s1 : 0000000000000001 a0 : 0000000000000019 a1 : ffffffff80e80bd8
[    1.675707]  a2 : 00000000ffffefff a3 : 00000000000000f4 a4 : 0000000000000002
[    1.682924]  a5 : 0000000000000001 a6 : 0000000000000030 a7 : 00000000028f5c29
[    1.690141]  s2 : 0000000000000800 s3 : ffffffe001375000 s4 : ffffffe01fdf7a80
[    1.697358]  s5 : ffffffe001375010 s6 : ffffffff8001fc10 s7 : ffffffffffffffff
[    1.704577]  s8 : 0000000000000001 s9 : ffffffff80ecb248 s10: ffffffe001b80000
[    1.711794]  s11: ffffffe001b80760 t3 : 0000000000000062 t4 : ffffffffffffffff
[    1.719012]  t5 : ffffffff80e0f6d8 t6 : ffffffd00411b8f0
[    1.724321] status: 8000000201800100 badaddr: 0000000000000000 cause: 0000000000000003
[    1.732233] [<ffffffff8023c2ec>] clk_core_disable+0xcc/0xec
[    1.737810] [<ffffffff80240430>] clk_disable+0x38/0x78
[    1.742956] [<ffffffff8001fc0c>] worker_thread+0x1a8/0x4d8
[    1.748451] [<ffffffff8031a500>] stmmac_remove_config_dt+0x1c/0x4c
[    1.754646] [<ffffffff8031c8ec>] sun8i_dwmac_probe+0x378/0x82c
[    1.760484] [<ffffffff8001fc0c>] worker_thread+0x1a8/0x4d8
[    1.765975] [<ffffffff8029a6c8>] platform_probe+0x64/0xf0
[    1.771382] [<ffffffff8029833c>] really_probe.part.0+0x8c/0x30c
[    1.777305] [<ffffffff8029865c>] __driver_probe_device+0xa0/0x148
[    1.783402] [<ffffffff8029873c>] driver_probe_device+0x38/0x138
[    1.789324] [<ffffffff802989cc>] __device_attach_driver+0xd0/0x170
[    1.795508] [<ffffffff802988f8>] __driver_attach_async_helper+0xbc/0xc0
[    1.802125] [<ffffffff802965ac>] bus_for_each_drv+0x68/0xb4
[    1.807701] [<ffffffff80298d1c>] __device_attach+0xd8/0x184
[    1.813277] [<ffffffff802967b0>] bus_probe_device+0x98/0xbc
[    1.818852] [<ffffffff80297904>] deferred_probe_work_func+0x90/0xd4
[    1.825122] [<ffffffff8001f8b8>] process_one_work+0x1e4/0x390
[    1.830872] [<ffffffff8001fd80>] worker_thread+0x31c/0x4d8
[    1.836362] [<ffffffff80026bf4>] kthreadd+0x94/0x188
[    1.841335] [<ffffffff80026bf4>] kthreadd+0x94/0x188
[    1.846304] [<ffffffff8001fa60>] process_one_work+0x38c/0x390
[    1.852054] [<ffffffff80026564>] kthread+0x124/0x160
[    1.857021] [<ffffffff8002643c>] set_kthread_struct+0x5c/0x60
[    1.862770] [<ffffffff80001f08>] ret_from_syscall_rejected+0x8/0xc
[    1.868956] ---[ end trace 8d5c6046255f84a0 ]---
[    1.873675] ------------[ cut here ]------------
[    1.878366] bus-emac already unprepared
[    1.882378] WARNING: CPU: 0 PID: 38 at drivers/clk/clk.c:810 clk_core_unprepare+0xe4/0x168
[    1.890673] CPU: 0 PID: 38 Comm: kworker/u2:1 Tainted: G        W 5.14.0-rc4 #1
[    1.898674] Hardware name: Allwinner D1 NeZha (DT)
[    1.903464] Workqueue: events_unbound deferred_probe_work_func
[    1.909305] epc : clk_core_unprepare+0xe4/0x168
[    1.913840]  ra : clk_core_unprepare+0xe4/0x168
[    1.918375] epc : ffffffff8023d6cc ra : ffffffff8023d6cc sp : ffffffd00411bb10
[    1.925593]  gp : ffffffff80ec9988 tp : ffffffe00143a800 t0 : 0000000000000002
[    1.932811]  t1 : ffffffe01f743be0 t2 : 0000000000000040 s0 : ffffffe001509e00
[    1.940029]  s1 : 0000000000000001 a0 : 000000000000001b a1 : ffffffe00143a800
[    1.947246]  a2 : 0000000000000000 a3 : 00000000000000f4 a4 : 0000000000000001
[    1.954463]  a5 : 0000000000000000 a6 : 0000000005fce2a5 a7 : 0000000000000001
[    1.961680]  s2 : 0000000000000800 s3 : ffffffff80afeb90 s4 : ffffffe01fdf7a80
[    1.968898]  s5 : ffffffe001375010 s6 : ffffffff8001fc10 s7 : ffffffffffffffff
[    1.976115]  s8 : 0000000000000001 s9 : ffffffff80ecb248 s10: ffffffe001b80000
[    1.983333]  s11: ffffffe001b80760 t3 : ffffffff80b39120 t4 : 0000000000000001
[    1.990550]  t5 : 0000000000000000 t6 : ffffffe001600002
[    1.995859] status: 8000000201800120 badaddr: 0000000000000000 cause: 0000000000000003
[    2.003771] [<ffffffff8023d6cc>] clk_core_unprepare+0xe4/0x168
[    2.009609] [<ffffffff802403a0>] clk_unprepare+0x24/0x3c
[    2.014929] [<ffffffff8031a508>] stmmac_remove_config_dt+0x24/0x4c
[    2.021125] [<ffffffff8031c8ec>] sun8i_dwmac_probe+0x378/0x82c
[    2.026965] [<ffffffff8001fc0c>] worker_thread+0x1a8/0x4d8
[    2.032463] [<ffffffff8029a6c8>] platform_probe+0x64/0xf0
[    2.037871] [<ffffffff8029833c>] really_probe.part.0+0x8c/0x30c
[    2.043795] [<ffffffff8029865c>] __driver_probe_device+0xa0/0x148
[    2.049892] [<ffffffff8029873c>] driver_probe_device+0x38/0x138
[    2.055815] [<ffffffff802989cc>] __device_attach_driver+0xd0/0x170
[    2.061999] [<ffffffff802988f8>] __driver_attach_async_helper+0xbc/0xc0
[    2.068616] [<ffffffff802965ac>] bus_for_each_drv+0x68/0xb4
[    2.074193] [<ffffffff80298d1c>] __device_attach+0xd8/0x184
[    2.079769] [<ffffffff802967b0>] bus_probe_device+0x98/0xbc
[    2.085345] [<ffffffff80297904>] deferred_probe_work_func+0x90/0xd4
[    2.091616] [<ffffffff8001f8b8>] process_one_work+0x1e4/0x390
[    2.097367] [<ffffffff8001fd80>] worker_thread+0x31c/0x4d8
[    2.102858] [<ffffffff80026bf4>] kthreadd+0x94/0x188
[    2.107830] [<ffffffff80026bf4>] kthreadd+0x94/0x188
[    2.112800] [<ffffffff8001fa60>] process_one_work+0x38c/0x390
[    2.118551] [<ffffffff80026564>] kthread+0x124/0x160
[    2.123520] [<ffffffff8002643c>] set_kthread_struct+0x5c/0x60
[    2.129268] [<ffffffff80001f08>] ret_from_syscall_rejected+0x8/0xc
[    2.135455] ---[ end trace 8d5c6046255f84a1 ]---

Fixes: 5ec55823438e ("net: stmmac: add clocks management for gmac driver")
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: stmmac: dwmac-visconti: No change to ETHER_CLOCK_SEL for unexpected speed request.

commit 928d6fe996f69330ded6b887baf4534c5fac7988 upstream.

Variable clk_sel_val is not initialized in the default case of the first switch statement.
In that case, the function should return immediately without any changes to the hardware.

Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: b38dd98ff8d0 ("net: stmmac: Add Toshiba Visconti SoCs glue driver")
Signed-off-by: Yuji Ishikawa <yuji2.ishikawa@toshiba.co.jp>
Reviewed-by: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net/smc: Forward wakeup to smc socket waitqueue after fallback

commit 341adeec9adad0874f29a0a1af35638207352a39 upstream.

When we replace TCP with SMC and a fallback occurs, there may be
some socket waitqueue entries remaining in smc socket->wq, such
as eppoll_entries inserted by userspace applications.

After the fallback, data flows over TCP/IP and only clcsocket->wq
will be woken up. Applications can't be notified by the entries
which were inserted in smc socket->wq before fallback. So we need
a mechanism to wake up smc socket->wq at the same time if some
entries remaining in it.

The current workaround is to transfer the entries from smc socket->wq
to clcsock->wq during the fallback. But this may cause a crash
like this:

 general protection fault, probably for non-canonical address 0xdead000000000100: 0000 [#1] PREEMPT SMP PTI
 CPU: 3 PID: 0 Comm: swapper/3 Kdump: loaded Tainted: G E     5.16.0+ #107
 RIP: 0010:__wake_up_common+0x65/0x170
 Call Trace:
  <IRQ>
  __wake_up_common_lock+0x7a/0xc0
  sock_def_readable+0x3c/0x70
  tcp_data_queue+0x4a7/0xc40
  tcp_rcv_established+0x32f/0x660
  ? sk_filter_trim_cap+0xcb/0x2e0
  tcp_v4_do_rcv+0x10b/0x260
  tcp_v4_rcv+0xd2a/0xde0
  ip_protocol_deliver_rcu+0x3b/0x1d0
  ip_local_deliver_finish+0x54/0x60
  ip_local_deliver+0x6a/0x110
  ? tcp_v4_early_demux+0xa2/0x140
  ? tcp_v4_early_demux+0x10d/0x140
  ip_sublist_rcv_finish+0x49/0x60
  ip_sublist_rcv+0x19d/0x230
  ip_list_rcv+0x13e/0x170
  __netif_receive_skb_list_core+0x1c2/0x240
  netif_receive_skb_list_internal+0x1e6/0x320
  napi_complete_done+0x11d/0x190
  mlx5e_napi_poll+0x163/0x6b0 [mlx5_core]
  __napi_poll+0x3c/0x1b0
  net_rx_action+0x27c/0x300
  __do_softirq+0x114/0x2d2
  irq_exit_rcu+0xb4/0xe0
  common_interrupt+0xba/0xe0
  </IRQ>
  <TASK>

The crash is caused by privately transferring waitqueue entries from
smc socket->wq to clcsock->wq. The owners of these entries, such as
epoll, have no idea that the entries have been transferred to a
different socket wait queue and still use original waitqueue spinlock
(smc socket->wq.wait.lock) to make the entries operation exclusive,
but it doesn't work. The operations to the entries, such as removing
from the waitqueue (now is clcsock->wq after fallback), may cause a
crash when clcsock waitqueue is being iterated over at the moment.

This patch tries to fix this by no longer transferring wait queue
entries privately, but introducing own implementations of clcsock's
callback functions in fallback situation. The callback functions will
forward the wakeup to smc socket->wq if clcsock->wq is actually woken
up and smc socket->wq has remaining entries.

Fixes: 2153bd1e3d3d ("net/smc: Transfer remaining wait queue entries during fallback")
Suggested-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Wen Gu <guwen@linux.alibaba.com>
Acked-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: ieee802154: Return meaningful error codes from the netlink helpers

commit 79c37ca73a6e9a33f7b2b7783ba6af07a448c8a9 upstream.

Returning -1 does not indicate anything useful.

Use a standard and meaningful error code instead.

Fixes: a26c5fd7622d ("nl802154: add support for security layer")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Alexander Aring <aahringo@redhat.com>
Link: https://lore.kernel.org/r/20220125121426.848337-6-miquel.raynal@bootlin.com
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

netfilter: nft_reject_bridge: Fix for missing reply from prerouting

commit aeac4554eb549037ff2f719200c0a9c1c25e7eaa upstream.

Prior to commit fa538f7cf05aa ("netfilter: nf_reject: add reject skbuff
creation helpers"), nft_reject_bridge did not assign to nskb->dev before
passing nskb on to br_forward(). The shared skbuff creation helpers
introduced in above commit do which seems to confuse br_forward() as
reject statements in prerouting hook won't emit a packet anymore.

Fix this by simply passing NULL instead of 'dev' to the helpers - they
use the pointer for just that assignment, nothing else.

Fixes: fa538f7cf05aa ("netfilter: nf_reject: add reject skbuff creation helpers")
Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: ieee802154: ca8210: Stop leaking skb's

commit 621b24b09eb61c63f262da0c9c5f0e93348897e5 upstream.

Upon error the ieee802154_xmit_complete() helper is not called. Only
ieee802154_wake_queue() is called manually. We then leak the skb
structure.

Free the skb structure upon error before returning.

Fixes: ded845a781a5 ("ieee802154: Add CA8210 IEEE 802.15.4 device driver")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Alexander Aring <aahringo@redhat.com>
Link: https://lore.kernel.org/r/20220125121426.848337-5-miquel.raynal@bootlin.com
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: ieee802154: mcr20a: Fix lifs/sifs periods

commit d753c4004820a888ec007dd88b271fa9c3172c5c upstream.

These periods are expressed in time units (microseconds) while 40 and 12
are the number of symbol durations these periods will last. We need to
multiply them both with phy->symbol_duration in order to get these
values in microseconds.

Fixes: 8c6ad9cc5157 ("ieee802154: Add NXP MCR20A IEEE 802.15.4 transceiver driver")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Alexander Aring <aahringo@redhat.com>
Link: https://lore.kernel.org/r/20220125121426.848337-3-miquel.raynal@bootlin.com
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: ieee802154: hwsim: Ensure proper channel selection at probe time

commit 1293fccc9e892712d910ec96079d3717307f1d2d upstream.

Drivers are expected to set the PHY current_channel and current_page
according to their default state. The hwsim driver is advertising being
configured on channel 13 by default but that is not reflected in its own
internal pib structure. In order to ensure that this driver consider the
current channel as being 13 internally, we at least need to set the
pib->channel field to 13.

Fixes: f25da51fdc38 ("ieee802154: hwsim: add replacement for fakelb")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
[stefan@datenfreihafen.org: fixed assigment from page to channel]
Acked-by: Alexander Aring <aahringo@redhat.com>
Link: https://lore.kernel.org/r/20220125121426.848337-2-miquel.raynal@bootlin.com
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

IB/cm: Release previously acquired reference counter in the cm_id_priv

commit b856101a1774b5f1c8c99e8dfdef802856520732 upstream.

In failure flow, the reference counter acquired was not released,
and the following error was reported:

  drivers/infiniband/core/cm.c:3373 cm_lap_handler() warn: inconsistent
refcounting 'cm_id_priv->refcount.refs.counter':

Fixes: 7345201c3963 ("IB/cm: Improve the calling of cm_init_av_for_lap and cm_init_av_by_path")
Link: https://lore.kernel.org/r/7615f23bbb5c5b66d03f6fa13e1c99d51dae6916.1642581448.git.leonro@nvidia.com
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mark Zhang <markzhang@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

IB/hfi1: Fix tstats alloc and dealloc

commit e5cce44aff3be9ad2cd52f63f35edbd706181d50 upstream.

The tstats allocation is done in the accelerated ndo_init function but the
allocation is not tested to succeed.

The deallocation is not done in the accelerated ndo_uninit function.

Resolve issues by testing for an allocation failure and adding the
free_percpu in the uninit function.

Fixes: aa0616a9bd52 ("IB/hfi1: switch to core handling of rx/tx byte/packet counters")
Link: https://lore.kernel.org/r/1642287756-182313-5-git-send-email-mike.marciniszyn@cornelisnetworks.com
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@cornelisnetworks.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@cornelisnetworks.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

spi: uniphier: fix reference count leak in uniphier_spi_probe()

commit 37c2c83ca4f1ef4b6908181ac98e18360af89b42 upstream.

The issue happens in several error paths in uniphier_spi_probe().
When either dma_get_slave_caps() or devm_spi_register_master() returns
an error code, the function forgets to decrease the refcount of both
`dma_rx` and `dma_tx` objects, which may lead to refcount leaks.

Fix it by decrementing the reference count of specific objects in
those error paths.

Signed-off-by: Xin Xiong <xiongx18@fudan.edu.cn>
Signed-off-by: Xiyu Yang <xiyuyang19@fudan.edu.cn>
Signed-off-by: Xin Tan <tanxin.ctf@gmail.com>
Reviewed-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Fixes: 28d1dddc59f6 ("spi: uniphier: Add DMA transfer mode support")
Link: https://lore.kernel.org/r/20220125101214.35677-1-xiongx18@fudan.edu.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

spi: meson-spicc: add IRQ check in meson_spicc_probe

commit e937440f7fc444a3e3f1fb75ea65292d6f433a44 upstream.

This check misses checking for  platform_get_irq()'s call and may passes
the negative error codes to devm_request_irq(), which takes unsigned IRQ #,
causing it to fail with -EINVAL, overriding an original error code.
Stop calling devm_request_irq() with invalid IRQ #s.

Fixes: 454fa271bc4e ("spi: Add Meson SPICC driver")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Link: https://lore.kernel.org/r/20220126110447.24549-1-linmq006@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

spi: mediatek: Avoid NULL pointer crash in interrupt

commit f83a96e5f033fbbd21764705cb9c04234b96218e upstream.

In some case, like after a transfer timeout, master->cur_msg pointer
is NULL which led to a kernel crash when trying to use master->cur_msg->spi.
mtk_spi_can_dma(), pointed by master->can_dma, doesn't use this parameter
avoid the problem by setting NULL as second parameter.

Fixes: a568231f46322 ("spi: mediatek: Add spi bus for Mediatek MT8173")
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@collabora.com>
Link: https://lore.kernel.org/r/20220131141708.888710-1-benjamin.gaignard@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

spi: bcm-qspi: check for valid cs before applying chip select

commit 2cbd27267ffe020af1442b95ec57f59a157ba85c upstream.

Apply only valid chip select value. This change fixes case where chip
select is set to initial value of '-1' during probe and  PM supend and
subsequent resume can try to use the value with undefined behaviour.
Also in case where gpio based chip select, the check in
bcm_qspi_chip_select() shall prevent undefined behaviour on resume.

Fixes: fa236a7ef240 ("spi: bcm-qspi: Add Broadcom MSPI driver")
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220127185359.27322-1-kdasu.kdev@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iommu/amd: Fix loop timeout issue in iommu_ga_log_enable()

commit 9b45a7738eec52bf0f5d8d3d54e822962781c5f2 upstream.

The polling loop for the register change in iommu_ga_log_enable() needs
to have a udelay() in it.  Otherwise the CPU might be faster than the
IOMMU hardware and wrongly trigger the WARN_ON() further down the code
stream. Use a 10us for udelay(), has there is some hardware where
activation of the GA log can take more than a 100ms.

A future optimization should move the activation check of the GA log
to the point where it gets used for the first time. But that is a
bigger change and not suitable for a fix.

Fixes: 8bda0cfbdc1a ("iommu/amd: Detect and initialize guest vAPIC log")
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Link: https://lore.kernel.org/r/20220204115537.3894-1-joro@8bytes.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iommu/vt-d: Fix potential memory leak in intel_setup_irq_remapping()

commit 99e675d473eb8cf2deac1376a0f840222fc1adcf upstream.

After commit e3beca48a45b ("irqdomain/treewide: Keep firmware node
unconditionally allocated"). For tear down scenario, fn is only freed
after fail to allocate ir_domain, though it also should be freed in case
dmar_enable_qi returns error.

Besides free fn, irq_domain and ir_msi_domain need to be removed as well
if intel_setup_irq_remapping fails to enable queued invalidation.

Improve the rewinding path by add out_free_ir_domain and out_free_fwnode
lables per Baolu's suggestion.

Fixes: e3beca48a45b ("irqdomain/treewide: Keep firmware node unconditionally allocated")
Suggested-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Guoqing Jiang <guoqing.jiang@linux.dev>
Link: https://lore.kernel.org/r/20220119063640.16864-1-guoqing.jiang@linux.dev
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/20220128031002.2219155-3-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ALSA: hda: Skip codec shutdown in case the codec is not registered

commit 1c7f0e349aa5f8f80b1cac3d4917405332e14cdf upstream.

If the codec->registered is not set then it means that pm_runtime is
not yet enabled and the codec->pcm_list_head has not been initialized.

The access to the not initialized pcm_list_head will lead a kernel crash
during shutdown.

Reported-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Tested-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Fixes: b98444ed597d ("ALSA: hda: Suspend codec at shutdown")
Link: https://lore.kernel.org/r/20220201112144.29411-1-peter.ujfalusi@linux.intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ALSA: hda: Fix signedness of sscanf() arguments

commit 0444f82766f0b5b9c8302ad802dafa5dd0e722d0 upstream.

The %x format of sscanf() takes an unsigned int pointer, while we pass
a signed int pointer.  Practically it's OK, but this may result in a
compile warning.  Let's fix it.

Fixes: a235d5b8e550 ("ALSA: hda: Allow model option to specify PCI SSID alias")
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/r/20220127135717.31751-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ALSA: usb-audio: initialize variables that could ignore errors

commit 3da4b7403db87d39bc2613cfd790de1de99a70ab upstream.

clang static analysis reports this representative issue
mixer.c:1548:35: warning: Assigned value is garbage or undefined
        ucontrol->value.integer.value[0] = val;
                                         ^ ~~~

The filter_error() macro allows errors to be ignored.
If errors can be ignored, initialize variables
so garbage will not be used.

Fixes: 48cc42973509 ("ALSA: usb-audio: Filter error from connector kctl ops, too")
Signed-off-by: Tom Rix <trix@redhat.com>
Link: https://lore.kernel.org/r/20220126182142.1184819-1-trix@redhat.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

RDMA/mlx4: Don't continue event handler after memory allocation failure

commit f3136c4ce7acf64bee43135971ca52a880572e32 upstream.

The failure to allocate memory during MLX4_DEV_EVENT_PORT_MGMT_CHANGE
event handler will cause skip the assignment logic, but
ib_dispatch_event() will be called anyway.

Fix it by calling to return instead of break after memory allocation
failure.

Fixes: 00f5ce99dc6e ("mlx4: Use port management change event instead of smp_snoop")
Link: https://lore.kernel.org/r/12a0e83f18cfad4b5f62654f141e240d04915e10.1643622264.git.leonro@nvidia.com
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Håkon Bugge <haakon.bugge@oracle.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

RDMA/siw: Fix broken RDMA Read Fence/Resume logic.

commit b43a76f423aa304037603fd6165c4a534d2c09a7 upstream.

Code unconditionally resumed fenced SQ processing after next RDMA Read
completion, even if other RDMA Read responses are still outstanding, or
ORQ is full. Also adds comments for better readability of fence
processing, and removes orq_get_tail() helper, which is not needed
anymore.

Fixes: 8b6a361b8c48 ("rdma/siw: receive path")
Fixes: a531975279f3 ("rdma/siw: main include file")
Link: https://lore.kernel.org/r/20220130170815.1940-1-bmt@zurich.ibm.com
Reported-by: Jared Holzman <jared.holzman@excelero.com>
Signed-off-by: Bernard Metzler <bmt@zurich.ibm.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

IB/rdmavt: Validate remote_addr during loopback atomic tests

commit 4028bccb003cf67e46632dee7f97ddc5d7b6e685 upstream.

The rdma-core test suite sends an unaligned remote address and expects a
failure.

ERROR: test_atomic_non_aligned_addr (tests.test_atomic.AtomicTest)

The qib/hfi1 rc handling validates properly, but the test has the client
and server on the same system.

The loopback of these operations is a distinct code path.

Fix by syntaxing the proposed remote address in the loopback code path.

Fixes: 15703461533a ("IB/{hfi1, qib, rdmavt}: Move ruc_loopback to rdmavt")
Link: https://lore.kernel.org/r/1642584489-141005-1-git-send-email-mike.marciniszyn@cornelisnetworks.com
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@cornelisnetworks.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@cornelisnetworks.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

RDMA/siw: Fix refcounting leak in siw_create_qp()

commit a75badebfdc0b3823054bedf112edb54d6357c75 upstream.

The atomic_inc() needs to be paired with an atomic_dec() on the error
path.

Fixes: 514aee660df4 ("RDMA: Globally allocate and release QP memory")
Link: https://lore.kernel.org/r/20220118091104.GA11671@kili
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Bernard Metzler <bmt@zurich.ibm.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

RDMA/ucma: Protect mc during concurrent multicast leaves

commit 36e8169ec973359f671f9ec7213547059cae972e upstream.

Partially revert the commit mentioned in the Fixes line to make sure that
allocation and erasing multicast struct are locked.

  BUG: KASAN: use-after-free in ucma_cleanup_multicast drivers/infiniband/core/ucma.c:491 [inline]
  BUG: KASAN: use-after-free in ucma_destroy_private_ctx+0x914/0xb70 drivers/infiniband/core/ucma.c:579
  Read of size 8 at addr ffff88801bb74b00 by task syz-executor.1/25529
  CPU: 0 PID: 25529 Comm: syz-executor.1 Not tainted 5.16.0-rc7-syzkaller #0
  Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
  Call Trace:
   __dump_stack lib/dump_stack.c:88 [inline]
   dump_stack_lvl+0xcd/0x134 lib/dump_stack.c:106
   print_address_description.constprop.0.cold+0x8d/0x320 mm/kasan/report.c:247
   __kasan_report mm/kasan/report.c:433 [inline]
   kasan_report.cold+0x83/0xdf mm/kasan/report.c:450
   ucma_cleanup_multicast drivers/infiniband/core/ucma.c:491 [inline]
   ucma_destroy_private_ctx+0x914/0xb70 drivers/infiniband/core/ucma.c:579
   ucma_destroy_id+0x1e6/0x280 drivers/infiniband/core/ucma.c:614
   ucma_write+0x25c/0x350 drivers/infiniband/core/ucma.c:1732
   vfs_write+0x28e/0xae0 fs/read_write.c:588
   ksys_write+0x1ee/0x250 fs/read_write.c:643
   do_syscall_x64 arch/x86/entry/common.c:50 [inline]
   do_syscall_64+0x35/0xb0 arch/x86/entry/common.c:80
   entry_SYSCALL_64_after_hwframe+0x44/0xae

Currently the xarray search can touch a concurrently freeing mc as the
xa_for_each() is not surrounded by any lock. Rather than hold the lock for
a full scan hold it only for the effected items, which is usually an empty
list.

Fixes: 95fe51096b7a ("RDMA/ucma: Remove mc_list and rely on xarray")
Link: https://lore.kernel.org/r/1cda5fabb1081e8d16e39a48d3a4f8160cea88b8.1642491047.git.leonro@nvidia.com
Reported-by: syzbot+e3f96c43d19782dd14a7@syzkaller.appspotmail.com
Suggested-by: Jason Gunthorpe <jgg@nvidia.com>
Reviewed-by: Maor Gottlieb <maorg@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

RDMA/cma: Use correct address when leaving multicast group

commit d9e410ebbed9d091b97bdf45b8a3792e2878dc48 upstream.

In RoCE we should use cma_iboe_set_mgid() and not cma_set_mgid to generate
the mgid, otherwise we will generate an IGMP for an incorrect address.

Fixes: b5de0c60cc30 ("RDMA/cma: Fix use after free race in roce multicast join")
Link: https://lore.kernel.org/r/913bc6783fd7a95fe71ad9454e01653ee6fb4a9a.1642491047.git.leonro@nvidia.com
Signed-off-by: Maor Gottlieb <maorg@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

KVM: arm64: Stop handle_exit() from handling HVC twice when an SError occurs

commit 1229630af88620f6e3a621a1ebd1ca14d9340df7 upstream.

Prior to commit defe21f49bc9 ("KVM: arm64: Move PC rollback on SError to
HYP"), when an SError is synchronised due to another exception, KVM
handles the SError first. If the guest survives, the instruction that
triggered the original exception is re-exectued to handle the first
exception. HVC is treated as a special case as the instruction wouldn't
normally be re-exectued, as its not a trap.

Commit defe21f49bc9 didn't preserve the behaviour of the 'return 1'
that skips the rest of handle_exit().

Since commit defe21f49bc9, KVM will try to handle the SError and the
original exception at the same time. When the exception was an HVC,
fixup_guest_exit() has already rolled back ELR_EL2, meaning if the
guest has virtual SError masked, it will execute and handle the HVC
twice.

Restore the original behaviour.

Fixes: defe21f49bc9 ("KVM: arm64: Move PC rollback on SError to HYP")
Cc: stable@vger.kernel.org
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20220127122052.1584324-4-james.morse@arm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

KVM: arm64: Avoid consuming a stale esr value when SError occur

commit 1c71dbc8a179d99dd9bb7e7fc1888db613cf85de upstream.

When any exception other than an IRQ occurs, the CPU updates the ESR_EL2
register with the exception syndrome. An SError may also become pending,
and will be synchronised by KVM. KVM notes the exception type, and whether
an SError was synchronised in exit_code.

When an exception other than an IRQ occurs, fixup_guest_exit() updates
vcpu->arch.fault.esr_el2 from the hardware register. When an SError was
synchronised, the vcpu esr value is used to determine if the exception
was due to an HVC. If so, ELR_EL2 is moved back one instruction. This
is so that KVM can process the SError first, and re-execute the HVC if
the guest survives the SError.

But if an IRQ synchronises an SError, the vcpu's esr value is stale.
If the previous non-IRQ exception was an HVC, KVM will corrupt ELR_EL2,
causing an unrelated guest instruction to be executed twice.

Check ARM_EXCEPTION_CODE() before messing with ELR_EL2, IRQs don't
update this register so don't need to check.

Fixes: defe21f49bc9 ("KVM: arm64: Move PC rollback on SError to HYP")
Cc: stable@vger.kernel.org
Reported-by: Steven Price <steven.price@arm.com>
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20220127122052.1584324-3-james.morse@arm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Revert "ASoC: mediatek: Check for error clk pointer"

This reverts commit 38accfd85e41b7ca547c5a7d4866bbc1462950cb which is
commit 9de2b9286a6dd16966959b3cb34fc2ddfd39213e upstream

With this patch in the tree, Chromebooks running the affected hardware
no longer boot. Bisect points to this patch, and reverting it fixes
the problem.

An analysis of the code with this patch applied shows:

        ret = init_clks(pdev, clk);
        if (ret)
                return ERR_PTR(ret);
...
                for (j = 0; j < MAX_CLKS && data->clk_id[j]; j++) {
                        struct clk *c = clk[data->clk_id[j]];

                        if (IS_ERR(c)) {
                                dev_err(&pdev->dev, "%s: clk unavailable\n",
                                        data->name);
                                return ERR_CAST(c);
                        }

                        scpd->clk[j] = c;
                }

Not all clocks in the clk_names array have to be present. Only the clocks
in the data->clk_id array are actually needed. The code already checks if
the required clocks are available and bails out if not. The assumption that
all clocks have to be present is wrong, and commit 9de2b9286a6d needs to be
reverted.

Fixes: 9de2b9286a6d ("ASoC: mediatek: Check for error clk pointer")
Cc: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Cc: Mark Brown <broonie@kernel.org>
Cc: James Liao <jamesjj.liao@mediatek.com>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Matthias Brugger <matthias.bgg@gmail.com
Cc: Frank Wunderlich <frank-w@public-files.de>
Cc: Daniel Golle <daniel@makrotopia.org>
Link: https://lore.kernel.org/lkml/20220205014755.699603-1-linux@roeck-us.net/
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mptcp: fix msk traversal in mptcp_nl_cmd_set_flags()

commit 8e9eacad7ec7a9cbf262649ebf1fa6e6f6cc7d82 upstream.

The MPTCP endpoint list is under RCU protection, guarded by the
pernet spinlock. mptcp_nl_cmd_set_flags() traverses the list
without acquiring the spin-lock nor under the RCU critical section.

This change addresses the issue performing the lookup and the endpoint
update under the pernet spinlock.

[The upstream commit had to handle a lookup_by_id variable that is only
 present in 5.17. This version of the patch removes that variable, so
 the __lookup_addr() function only handles the lookup as it is
 implemented in 5.15 and 5.16. It also removes one 'const' keyword to
 prevent a warning due to differing const-ness in the 5.17 version of
 addresses_equal().]

Fixes: 0f9f696a502e ("mptcp: add set_flags command in PM netlink")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

fbcon: Add option to enable legacy hardware acceleration

commit a3f781a9d6114c1d1e01defb7aa234dec45d2a5f upstream.

Add a config option CONFIG_FRAMEBUFFER_CONSOLE_LEGACY_ACCELERATION to
enable bitblt and fillrect hardware acceleration in the framebuffer
console. If disabled, such acceleration will not be used, even if it is
supported by the graphics hardware driver.

If you plan to use DRM as your main graphics output system, you should
disable this option since it will prevent compiling in code which isn't
used later on when DRM takes over.

For all other configurations, e.g. if none of your graphic cards support
DRM (yet), DRM isn't available for your architecture, or you can't be
sure that the graphic card in the target system will support DRM, you
most likely want to enable this option.

In the non-accelerated case (e.g. when DRM is used), the inlined
fb_scrollmode() function is hardcoded to return SCROLL_REDRAW and as such the
compiler is able to optimize much unneccesary code away.

In this v3 patch version I additionally changed the GETVYRES() and GETVXRES()
macros to take a pointer to the fbcon_display struct. This fixes the build when
console rotation is enabled and helps the compiler again to optimize out code.

Signed-off-by: Helge Deller <deller@gmx.de>
Cc: stable@vger.kernel.org # v5.10+
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20220202135531.92183-4-deller@gmx.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Revert "fbcon: Disable accelerated scrolling"

commit 87ab9f6b7417349aa197a6c7098d4fdd4beebb74 upstream.

This reverts commit 39aead8373b3c20bb5965c024dfb51a94e526151.

Revert the first (of 2) commits which disabled scrolling acceleration in
fbcon/fbdev.  It introduced a regression for fbdev-supported graphic cards
because of the performance penalty by doing screen scrolling by software
instead of using the existing graphic card 2D hardware acceleration.

Console scrolling acceleration was disabled by dropping code which
checked at runtime the driver hardware capabilities for the
BINFO_HWACCEL_COPYAREA or FBINFO_HWACCEL_FILLRECT flags and if set, it
enabled scrollmode SCROLL_MOVE which uses hardware acceleration to move
screen contents.  After dropping those checks scrollmode was hard-wired
to SCROLL_REDRAW instead, which forces all graphic cards to redraw every
character at the new screen position when scrolling.

This change effectively disabled all hardware-based scrolling acceleration for
ALL drivers, because now all kind of 2D hardware acceleration (bitblt,
fillrect) in the drivers isn't used any longer.

The original commit message mentions that only 3 DRM drivers (nouveau, omapdrm
and gma500) used hardware acceleration in the past and thus code for checking
and using scrolling acceleration is obsolete.

This statement is NOT TRUE, because beside the DRM drivers there are around 35
other fbdev drivers which depend on fbdev/fbcon and still provide hardware
acceleration for fbdev/fbcon.

The original commit message also states that syzbot found lots of bugs in fbcon
and thus it's "often the solution to just delete code and remove features".
This is true, and the bugs - which actually affected all users of fbcon,
including DRM - were fixed, or code was dropped like e.g. the support for
software scrollback in vgacon (commit 973c096f6a85).

So to further analyze which bugs were found by syzbot, I've looked through all
patches in drivers/video which were tagged with syzbot or syzkaller back to
year 2005. The vast majority fixed the reported issues on a higher level, e.g.
when screen is to be resized, or when font size is to be changed. The few ones
which touched driver code fixed a real driver bug, e.g. by adding a check.

But NONE of those patches touched code of either the SCROLL_MOVE or the
SCROLL_REDRAW case.

That means, there was no real reason why SCROLL_MOVE had to be ripped-out and
just SCROLL_REDRAW had to be used instead. The only reason I can imagine so far
was that SCROLL_MOVE wasn't used by DRM and as such it was assumed that it
could go away. That argument completely missed the fact that SCROLL_MOVE is
still heavily used by fbdev (non-DRM) drivers.

Some people mention that using memcpy() instead of the hardware acceleration is
pretty much the same speed. But that's not true, at least not for older graphic
cards and machines where we see speed decreases by factor 10 and more and thus
this change leads to console responsiveness way worse than before.

That's why the original commit is to be reverted. By reverting we
reintroduce hardware-based scrolling acceleration and fix the
performance regression for fbdev drivers.

There isn't any impact on DRM when reverting those patches.

Signed-off-by: Helge Deller <deller@gmx.de>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Sven Schnelle <svens@stackframe.org>
Cc: stable@vger.kernel.org # v5.10+
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20220202135531.92183-3-deller@gmx.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

IB/hfi1: Fix AIP early init panic

commit 5f8f55b92edd621f056bdf09e572092849fabd83 upstream.

An early failure in hfi1_ipoib_setup_rn() can lead to the following panic:

  BUG: unable to handle kernel NULL pointer dereference at 00000000000001b0
  PGD 0 P4D 0
  Oops: 0002 [#1] SMP NOPTI
  Workqueue: events work_for_cpu_fn
  RIP: 0010:try_to_grab_pending+0x2b/0x140
  Code: 1f 44 00 00 41 55 41 54 55 48 89 d5 53 48 89 fb 9c 58 0f 1f 44 00 00 48 89 c2 fa 66 0f 1f 44 00 00 48 89 55 00 40 84 f6 75 77 <f0> 48 0f ba 2b 00 72 09 31 c0 5b 5d 41 5c 41 5d c3 48 89 df e8 6c
  RSP: 0018:ffffb6b3cf7cfa48 EFLAGS: 00010046
  RAX: 0000000000000246 RBX: 00000000000001b0 RCX: 0000000000000000
  RDX: 0000000000000246 RSI: 0000000000000000 RDI: 00000000000001b0
  RBP: ffffb6b3cf7cfa70 R08: 0000000000000f09 R09: 0000000000000001
  R10: 0000000000000000 R11: 0000000000000001 R12: 0000000000000000
  R13: ffffb6b3cf7cfa90 R14: ffffffff9b2fbfc0 R15: ffff8a4fdf244690
  FS:  0000000000000000(0000) GS:ffff8a527f400000(0000) knlGS:0000000000000000
  CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
  CR2: 00000000000001b0 CR3: 00000017e2410003 CR4: 00000000007706f0
  DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
  DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
  PKRU: 55555554
  Call Trace:
   __cancel_work_timer+0x42/0x190
   ? dev_printk_emit+0x4e/0x70
   iowait_cancel_work+0x15/0x30 [hfi1]
   hfi1_ipoib_txreq_deinit+0x5a/0x220 [hfi1]
   ? dev_err+0x6c/0x90
   hfi1_ipoib_netdev_dtor+0x15/0x30 [hfi1]
   hfi1_ipoib_setup_rn+0x10e/0x150 [hfi1]
   rdma_init_netdev+0x5a/0x80 [ib_core]
   ? hfi1_ipoib_free_rdma_netdev+0x20/0x20 [hfi1]
   ipoib_intf_init+0x6c/0x350 [ib_ipoib]
   ipoib_intf_alloc+0x5c/0xc0 [ib_ipoib]
   ipoib_add_one+0xbe/0x300 [ib_ipoib]
   add_client_context+0x12c/0x1a0 [ib_core]
   enable_device_and_get+0xdc/0x1d0 [ib_core]
   ib_register_device+0x572/0x6b0 [ib_core]
   rvt_register_device+0x11b/0x220 [rdmavt]
   hfi1_register_ib_device+0x6b4/0x770 [hfi1]
   do_init_one.isra.20+0x3e3/0x680 [hfi1]
   local_pci_probe+0x41/0x90
   work_for_cpu_fn+0x16/0x20
   process_one_work+0x1a7/0x360
   ? create_worker+0x1a0/0x1a0
   worker_thread+0x1cf/0x390
   ? create_worker+0x1a0/0x1a0
   kthread+0x116/0x130
   ? kthread_flush_work_fn+0x10/0x10
   ret_from_fork+0x1f/0x40

The panic happens in hfi1_ipoib_txreq_deinit() because there is a NULL
deref when hfi1_ipoib_netdev_dtor() is called in this error case.

hfi1_ipoib_txreq_init() and hfi1_ipoib_rxq_init() are self unwinding so
fix by adjusting the error paths accordingly.

Other changes:
- hfi1_ipoib_free_rdma_netdev() is deleted including the free_netdev()
  since the netdev core code deletes calls free_netdev()
- The switch to the accelerated entrances is moved to the success path.

Cc: stable@vger.kernel.org
Fixes: d99dc602e2a5 ("IB/hfi1: Add functions to transmit datagram ipoib packets")
Link: https://lore.kernel.org/r/1642287756-182313-4-git-send-email-mike.marciniszyn@cornelisnetworks.com
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@cornelisnetworks.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@cornelisnetworks.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dma-buf: heaps: Fix potential spectre v1 gadget

commit 92c4cfaee6872038563c5b6f2e8e613f9d84d47d upstream.

It appears like nr could be a Spectre v1 gadget as it's supplied by a
user and used as an array index. Prevent the contents
of kernel memory from being leaked to userspace via speculative
execution by using array_index_nospec.

Signed-off-by: Jordy Zomer <jordy@pwning.systems>
Fixes: c02a81fba74f ("dma-buf: Add dma-buf heaps framework")
Cc: <stable@vger.kernel.org> # v5.6+
Acked-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org>
 [sumits: added fixes and cc: stable tags]
Link: https://patchwork.freedesktop.org/patch/msgid/20220129150604.3461652-1-jordy@pwning.systems
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

block: bio-integrity: Advance seed correctly for larger interval sizes

commit b13e0c71856817fca67159b11abac350e41289f5 upstream.

Commit 309a62fa3a9e ("bio-integrity: bio_integrity_advance must update
integrity seed") added code to update the integrity seed value when
advancing a bio. However, it failed to take into account that the
integrity interval might be larger than the 512-byte block layer
sector size. This broke bio splitting on PI devices with 4KB logical
blocks.

The seed value should be advanced by bio_integrity_intervals() and not
the number of sectors.

Cc: Dmitry Monakhov <dmonakhov@openvz.org>
Cc: stable@vger.kernel.org
Fixes: 309a62fa3a9e ("bio-integrity: bio_integrity_advance must update integrity seed")
Tested-by: Dmitry Ivanov <dmitry.ivanov2@hpe.com>
Reported-by: Alexey Lyashkov <alexey.lyashkov@hpe.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Link: https://lore.kernel.org/r/20220204034209.4193-1-martin.petersen@oracle.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mm/kmemleak: avoid scanning potential huge holes

commit c10a0f877fe007021d70f9cada240f42adc2b5db upstream.

When using devm_request_free_mem_region() and devm_memremap_pages() to
add ZONE_DEVICE memory, if requested free mem region's end pfn were
huge(e.g., 0x400000000), the node_end_pfn() will be also huge (see
move_pfn_range_to_zone()).  Thus it creates a huge hole between
node_start_pfn() and node_end_pfn().

We found on some AMD APUs, amdkfd requested such a free mem region and
created a huge hole.  In such a case, following code snippet was just
doing busy test_bit() looping on the huge hole.

  for (pfn = start_pfn; pfn < end_pfn; pfn++) {
struct page *page = pfn_to_online_page(pfn);
if (!page)
continue;
...
  }

So we got a soft lockup:

  watchdog: BUG: soft lockup - CPU#6 stuck for 26s! [bash:1221]
  CPU: 6 PID: 1221 Comm: bash Not tainted 5.15.0-custom #1
  RIP: 0010:pfn_to_online_page+0x5/0xd0
  Call Trace:
    ? kmemleak_scan+0x16a/0x440
    kmemleak_write+0x306/0x3a0
    ? common_file_perm+0x72/0x170
    full_proxy_write+0x5c/0x90
    vfs_write+0xb9/0x260
    ksys_write+0x67/0xe0
    __x64_sys_write+0x1a/0x20
    do_syscall_64+0x3b/0xc0
    entry_SYSCALL_64_after_hwframe+0x44/0xae

I did some tests with the patch.

(1) amdgpu module unloaded

before the patch:

  real    0m0.976s
  user    0m0.000s
  sys     0m0.968s

after the patch:

  real    0m0.981s
  user    0m0.000s
  sys     0m0.973s

(2) amdgpu module loaded

before the patch:

  real    0m35.365s
  user    0m0.000s
  sys     0m35.354s

after the patch:

  real    0m1.049s
  user    0m0.000s
  sys     0m1.042s

Link: https://lkml.kernel.org/r/20211108140029.721144-1-lang.yu@amd.com
Signed-off-by: Lang Yu <lang.yu@amd.com>
Acked-by: David Hildenbrand <david@redhat.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Oscar Salvador <osalvador@suse.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mm/pgtable: define pte_index so that preprocessor could recognize it

commit 314c459a6fe0957b5885fbc65c53d51444092880 upstream.

Since commit 974b9b2c68f3 ("mm: consolidate pte_index() and
pte_offset_*() definitions") pte_index is a static inline and there is
no define for it that can be recognized by the preprocessor.  As a
result, vm_insert_pages() uses slower loop over vm_insert_page() instead
of insert_pages() that amortizes the cost of spinlock operations when
inserting multiple pages.

Link: https://lkml.kernel.org/r/20220111145457.20748-1-rppt@kernel.org
Fixes: 974b9b2c68f3 ("mm: consolidate pte_index() and pte_offset_*() definitions")
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Reported-by: Christian Dietrich <stettberger@dokucode.de>
Reviewed-by: Khalid Aziz <khalid.aziz@oracle.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mm/debug_vm_pgtable: remove pte entry from the page table

commit fb5222aae64fe25e5f3ebefde8214dcf3ba33ca5 upstream.

Patch series "page table check fixes and cleanups", v5.

This patch (of 4):

The pte entry that is used in pte_advanced_tests() is never removed from
the page table at the end of the test.

The issue is detected by page_table_check, to repro compile kernel with
the following configs:

CONFIG_DEBUG_VM_PGTABLE=y
CONFIG_PAGE_TABLE_CHECK=y
CONFIG_PAGE_TABLE_CHECK_ENFORCED=y

During the boot the following BUG is printed:

  debug_vm_pgtable: [debug_vm_pgtable         ]: Validating architecture page table helpers
  ------------[ cut here ]------------
  kernel BUG at mm/page_table_check.c:162!
  invalid opcode: 0000 [#1] PREEMPT SMP PTI
  CPU: 0 PID: 1 Comm: swapper/0 Not tainted 5.16.0-11413-g2c271fe77d52 #3
  Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.15.0-0-g2dd4b9b3f840-prebuilt.qemu.org 04/01/2014
  ...

The entry should be properly removed from the page table before the page
is released to the free list.

Link: https://lkml.kernel.org/r/20220131203249.2832273-1-pasha.tatashin@soleen.com
Link: https://lkml.kernel.org/r/20220131203249.2832273-2-pasha.tatashin@soleen.com
Fixes: a5c3b9ffb0f4 ("mm/debug_vm_pgtable: add tests validating advanced arch page table helpers")
Signed-off-by: Pasha Tatashin <pasha.tatashin@soleen.com>
Reviewed-by: Zi Yan <ziy@nvidia.com>
Tested-by: Zi Yan <ziy@nvidia.com>
Acked-by: David Rientjes <rientjes@google.com>
Reviewed-by: Anshuman Khandual <anshuman.khandual@arm.com>
Cc: Paul Turner <pjt@google.com>
Cc: Wei Xu <weixugc@google.com>
Cc: Greg Thelen <gthelen@google.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Will Deacon <will@kernel.org>
Cc: Mike Rapoport <rppt@kernel.org>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: Muchun Song <songmuchun@bytedance.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: <stable@vger.kernel.org> [5.9+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

nvme-fabrics: fix state check in nvmf_ctlr_matches_baseopts()

commit 6a51abdeb259a56d95f13cc67e3a0838bcda0377 upstream.

Controller deletion/reset, immediately followed by or concurrent with
a reconnect, is hard failing the connect attempt resulting in a
complete loss of connectivity to the controller.

In the connect request, fabrics looks for an existing controller with
the same address components and aborts the connect if a controller
already exists and the duplicate connect option isn't set. The match
routine filters out controllers that are dead or dying, so they don't
interfere with the new connect request.

When NVME_CTRL_DELETING_NOIO was added, it missed updating the state
filters in the nvmf_ctlr_matches_baseopts() routine. Thus, when in this
new state, it's seen as a live controller and fails the connect request.

Correct by adding the DELETING_NIO state to the match checks.

Fixes: ecca390e8056 ("nvme: fix deadlock in disconnect during scan_work and/or ana_work")
Cc: <stable@vger.kernel.org> # v5.7+
Signed-off-by: Uday Shankar <ushankar@purestorage.com>
Reviewed-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/amd/display: Force link_rate as LINK_RATE_RBR2 for 2018 15" Apple Retina panels

commit 30fbce374745a9c6af93c775a5ac49a97f822fda upstream.

The eDP link rate reported by the DP_MAX_LINK_RATE dpcd register (0xa) is
contradictory to the highest rate supported reported by
EDID (0xc = LINK_RATE_RBR2). The effects of this compounded with commit
'4a8ca46bae8a ("drm/amd/display: Default max bpc to 16 for eDP")' results
in no display modes being found and a dark panel.

For now, simply force the maximum supported link rate for the eDP attached
2018 15" Apple Retina panels.

Additionally, we must also check the firmware revision since the device ID
reported by the DPCD is identical to that of the more capable 16,1,
incorrectly quirking it. We also use said firmware check to quirk the
refreshed 15,1 models with Vega graphics as they use a slightly newer
firmware version.

Tested-by: Aun-Ali Zaidi <admin@kodeit.net>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Aun-Ali Zaidi <admin@kodeit.net>
Signed-off-by: Aditya Garg <gargaditya08@live.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/amd/display: watermark latencies is not enough on DCN31

commit f5fa54f45ab41cbb1f99b1208f49554132ffb207 upstream.

[Why]
The original latencies were causing underflow in some modes.
Resolution: 2880x1620@60p when HDR enable

[How]
1. Replace with the up-to-date watermark values based on new measurments
2. Correct the ddr_wm_table name to DDR5 on DCN31

Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Signed-off-by: Paul Hsieh <paul.hsieh@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/amd/pm: correct the MGpuFanBoost support for Beige Goby

commit 3ec5586b4699cfb75cdfa09425e11d121db40773 upstream.

The existing way cannot handle Beige Goby well as a different
PPTable data structure(PPTable_beige_goby_t instead of PPTable_t)
is used there.

Signed-off-by: Evan Quan <evan.quan@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/i915/adlp: Fix TypeC PHY-ready status readout

commit 3c6f13ad723e7206f03bb2752b01d18202b7fc9d upstream.

The TCSS_DDI_STATUS register is indexed by tc_port not by the FIA port
index, fix this up. This only caused an issue on TC#3/4 ports in legacy
mode, as in all other cases the two indices either match (on TC#1/2) or
the TCSS_DDI_STATUS_READY flag is set regardless of something being
connected or not (on TC#1/2/3/4 in dp-alt and tbt-alt modes).

Reported-and-tested-by: Chia-Lin Kao (AceLan) <acelan.kao@canonical.com>
Fixes: 55ce306c2aa1 ("drm/i915/adl_p: Implement TC sequences")
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/4698
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: <stable@vger.kernel.org> # v5.14+
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220126104356.2022975-1-imre.deak@intel.com
(cherry picked from commit 516b33460c5bee78b2055637b0547bdb0e6af754)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/nouveau: fix off by one in BIOS boundary checking

commit 1b777d4d9e383d2744fc9b3a09af6ec1893c8b1a upstream.

Bounds checking when parsing init scripts embedded in the BIOS reject
access to the last byte. This causes driver initialization to fail on
Apple eMac's with GeForce 2 MX GPUs, leaving the system with no working
console.

This is probably only seen on OpenFirmware machines like PowerPC Macs
because the BIOS image provided by OF is only the used parts of the ROM,
not a power-of-two blocks read from PCI directly so PCs always have
empty bytes at the end that are never accessed.

Signed-off-by: Nick Lopez <github@glowingmonkey.org>
Fixes: 4d4e9907ff572 ("drm/nouveau/bios: guard against out-of-bounds accesses to image")
Cc: <stable@vger.kernel.org> # v4.10+
Reviewed-by: Ilia Mirkin <imirkin@alum.mit.edu>
Reviewed-by: Karol Herbst <kherbst@redhat.com>
Signed-off-by: Karol Herbst <kherbst@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220122081906.2633061-1-github@glowingmonkey.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Revert "fs/9p: search open fids first"

commit 22e424feb6658c5d6789e45121830357809c59cb upstream.

This reverts commit 478ba09edc1f2f2ee27180a06150cb2d1a686f9c.

That commit was meant as a fix for setattrs with by fd (e.g. ftruncate)
to use an open fid instead of the first fid it found on lookup.
The proper fix for that is to use the fid associated with the open file
struct, available in iattr->ia_file for such operations, and was
actually done just before in 66246641609b ("9p: retrieve fid from file
when file instance exist.")
As such, this commit is no longer required.

Furthermore, changing lookup to return open fids first had unwanted side
effects, as it turns out the protocol forbids the use of open fids for
further walks (e.g. clone_fid) and we broke mounts for some servers
enforcing this rule.

Note this only reverts to the old working behaviour, but it's still
possible for lookup to return open fids if dentry->d_fsdata is not set,
so more work is needed to make sure we respect this rule in the future,
for example by adding a flag to the lookup functions to only match
certain fid open modes depending on caller requirements.

Link: https://lkml.kernel.org/r/20220130130651.712293-1-asmadeus@codewreck.org
Fixes: 478ba09edc1f ("fs/9p: search open fids first")
Cc: stable@vger.kernel.org # v5.11+
Reported-by: ron minnich <rminnich@gmail.com>
Reported-by: ng@0x80.stream
Signed-off-by: Dominique Martinet <asmadeus@codewreck.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

btrfs: fix use-after-free after failure to create a snapshot

commit 28b21c558a3753171097193b6f6602a94169093a upstream.

At ioctl.c:create_snapshot(), we allocate a pending snapshot structure and
then attach it to the transaction's list of pending snapshots. After that
we call btrfs_commit_transaction(), and if that returns an error we jump
to 'fail' label, where we kfree() the pending snapshot structure. This can
result in a later use-after-free of the pending snapshot:

1) We allocated the pending snapshot and added it to the transaction's
   list of pending snapshots;

2) We call btrfs_commit_transaction(), and it fails either at the first
   call to btrfs_run_delayed_refs() or btrfs_start_dirty_block_groups().
   In both cases, we don't abort the transaction and we release our
   transaction handle. We jump to the 'fail' label and free the pending
   snapshot structure. We return with the pending snapshot still in the
   transaction's list;

3) Another task commits the transaction. This time there's no error at
   all, and then during the transaction commit it accesses a pointer
   to the pending snapshot structure that the snapshot creation task
   has already freed, resulting in a user-after-free.

This issue could actually be detected by smatch, which produced the
following warning:

  fs/btrfs/ioctl.c:843 create_snapshot() warn: '&pending_snapshot->list' not removed from list

So fix this by not having the snapshot creation ioctl directly add the
pending snapshot to the transaction's list. Instead add the pending
snapshot to the transaction handle, and then at btrfs_commit_transaction()
we add the snapshot to the list only when we can guarantee that any error
returned after that point will result in a transaction abort, in which
case the ioctl code can safely free the pending snapshot and no one can
access it anymore.

CC: stable@vger.kernel.org # 5.10+
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

btrfs: fix deadlock between quota disable and qgroup rescan worker

commit e804861bd4e69cc5fe1053eedcb024982dde8e48 upstream.

Quota disable ioctl starts a transaction before waiting for the qgroup
rescan worker completes. However, this wait can be infinite and results
in deadlock because of circular dependency among the quota disable
ioctl, the qgroup rescan worker and the other task with transaction such
as block group relocation task.

The deadlock happens with the steps following:

1) Task A calls ioctl to disable quota. It starts a transaction and
   waits for qgroup rescan worker completes.
2) Task B such as block group relocation task starts a transaction and
   joins to the transaction that task A started. Then task B commits to
   the transaction. In this commit, task B waits for a commit by task A.
3) Task C as the qgroup rescan worker starts its job and starts a
   transaction. In this transaction start, task C waits for completion
   of the transaction that task A started and task B committed.

This deadlock was found with fstests test case btrfs/115 and a zoned
null_blk device. The test case enables and disables quota, and the
block group reclaim was triggered during the quota disable by chance.
The deadlock was also observed by running quota enable and disable in
parallel with 'btrfs balance' command on regular null_blk devices.

An example report of the deadlock:

  [372.469894] INFO: task kworker/u16:6:103 blocked for more than 122 seconds.
  [372.479944]       Not tainted 5.16.0-rc8 #7
  [372.485067] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
  [372.493898] task:kworker/u16:6   state:D stack:    0 pid:  103 ppid:     2 flags:0x00004000
  [372.503285] Workqueue: btrfs-qgroup-rescan btrfs_work_helper [btrfs]
  [372.510782] Call Trace:
  [372.514092]  <TASK>
  [372.521684]  __schedule+0xb56/0x4850
  [372.530104]  ? io_schedule_timeout+0x190/0x190
  [372.538842]  ? lockdep_hardirqs_on+0x7e/0x100
  [372.547092]  ? _raw_spin_unlock_irqrestore+0x3e/0x60
  [372.555591]  schedule+0xe0/0x270
  [372.561894]  btrfs_commit_transaction+0x18bb/0x2610 [btrfs]
  [372.570506]  ? btrfs_apply_pending_changes+0x50/0x50 [btrfs]
  [372.578875]  ? free_unref_page+0x3f2/0x650
  [372.585484]  ? finish_wait+0x270/0x270
  [372.591594]  ? release_extent_buffer+0x224/0x420 [btrfs]
  [372.599264]  btrfs_qgroup_rescan_worker+0xc13/0x10c0 [btrfs]
  [372.607157]  ? lock_release+0x3a9/0x6d0
  [372.613054]  ? btrfs_qgroup_account_extent+0xda0/0xda0 [btrfs]
  [372.620960]  ? do_raw_spin_lock+0x11e/0x250
  [372.627137]  ? rwlock_bug.part.0+0x90/0x90
  [372.633215]  ? lock_is_held_type+0xe4/0x140
  [372.639404]  btrfs_work_helper+0x1ae/0xa90 [btrfs]
  [372.646268]  process_one_work+0x7e9/0x1320
  [372.652321]  ? lock_release+0x6d0/0x6d0
  [372.658081]  ? pwq_dec_nr_in_flight+0x230/0x230
  [372.664513]  ? rwlock_bug.part.0+0x90/0x90
  [372.670529]  worker_thread+0x59e/0xf90
  [372.676172]  ? process_one_work+0x1320/0x1320
  [372.682440]  kthread+0x3b9/0x490
  [372.687550]  ? _raw_spin_unlock_irq+0x24/0x50
  [372.693811]  ? set_kthread_struct+0x100/0x100
  [372.700052]  ret_from_fork+0x22/0x30
  [372.705517]  </TASK>
  [372.709747] INFO: task btrfs-transacti:2347 blocked for more than 123 seconds.
  [372.729827]       Not tainted 5.16.0-rc8 #7
  [372.745907] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
  [372.767106] task:btrfs-transacti state:D stack:    0 pid: 2347 ppid:     2 flags:0x00004000
  [372.787776] Call Trace:
  [372.801652]  <TASK>
  [372.812961]  __schedule+0xb56/0x4850
  [372.830011]  ? io_schedule_timeout+0x190/0x190
  [372.852547]  ? lockdep_hardirqs_on+0x7e/0x100
  [372.871761]  ? _raw_spin_unlock_irqrestore+0x3e/0x60
  [372.886792]  schedule+0xe0/0x270
  [372.901685]  wait_current_trans+0x22c/0x310 [btrfs]
  [372.919743]  ? btrfs_put_transaction+0x3d0/0x3d0 [btrfs]
  [372.938923]  ? finish_wait+0x270/0x270
  [372.959085]  ? join_transaction+0xc75/0xe30 [btrfs]
  [372.977706]  start_transaction+0x938/0x10a0 [btrfs]
  [372.997168]  transaction_kthread+0x19d/0x3c0 [btrfs]
  [373.013021]  ? btrfs_cleanup_transaction.isra.0+0xfc0/0xfc0 [btrfs]
  [373.031678]  kthread+0x3b9/0x490
  [373.047420]  ? _raw_spin_unlock_irq+0x24/0x50
  [373.064645]  ? set_kthread_struct+0x100/0x100
  [373.078571]  ret_from_fork+0x22/0x30
  [373.091197]  </TASK>
  [373.105611] INFO: task btrfs:3145 blocked for more than 123 seconds.
  [373.114147]       Not tainted 5.16.0-rc8 #7
  [373.120401] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
  [373.130393] task:btrfs           state:D stack:    0 pid: 3145 ppid:  3141 flags:0x00004000
  [373.140998] Call Trace:
  [373.145501]  <TASK>
  [373.149654]  __schedule+0xb56/0x4850
  [373.155306]  ? io_schedule_timeout+0x190/0x190
  [373.161965]  ? lockdep_hardirqs_on+0x7e/0x100
  [373.168469]  ? _raw_spin_unlock_irqrestore+0x3e/0x60
  [373.175468]  schedule+0xe0/0x270
  [373.180814]  wait_for_commit+0x104/0x150 [btrfs]
  [373.187643]  ? test_and_set_bit+0x20/0x20 [btrfs]
  [373.194772]  ? kmem_cache_free+0x124/0x550
  [373.201191]  ? btrfs_put_transaction+0x69/0x3d0 [btrfs]
  [373.208738]  ? finish_wait+0x270/0x270
  [373.214704]  ? __btrfs_end_transaction+0x347/0x7b0 [btrfs]
  [373.222342]  btrfs_commit_transaction+0x44d/0x2610 [btrfs]
  [373.230233]  ? join_transaction+0x255/0xe30 [btrfs]
  [373.237334]  ? btrfs_record_root_in_trans+0x4d/0x170 [btrfs]
  [373.245251]  ? btrfs_apply_pending_changes+0x50/0x50 [btrfs]
  [373.253296]  relocate_block_group+0x105/0xc20 [btrfs]
  [373.260533]  ? mutex_lock_io_nested+0x1270/0x1270
  [373.267516]  ? btrfs_wait_nocow_writers+0x85/0x180 [btrfs]
  [373.275155]  ? merge_reloc_roots+0x710/0x710 [btrfs]
  [373.283602]  ? btrfs_wait_ordered_extents+0xd30/0xd30 [btrfs]
  [373.291934]  ? kmem_cache_free+0x124/0x550
  [373.298180]  btrfs_relocate_block_group+0x35c/0x930 [btrfs]
  [373.306047]  btrfs_relocate_chunk+0x85/0x210 [btrfs]
  [373.313229]  btrfs_balance+0x12f4/0x2d20 [btrfs]
  [373.320227]  ? lock_release+0x3a9/0x6d0
  [373.326206]  ? btrfs_relocate_chunk+0x210/0x210 [btrfs]
  [373.333591]  ? lock_is_held_type+0xe4/0x140
  [373.340031]  ? rcu_read_lock_sched_held+0x3f/0x70
  [373.346910]  btrfs_ioctl_balance+0x548/0x700 [btrfs]
  [373.354207]  btrfs_ioctl+0x7f2/0x71b0 [btrfs]
  [373.360774]  ? lockdep_hardirqs_on_prepare+0x410/0x410
  [373.367957]  ? lockdep_hardirqs_on_prepare+0x410/0x410
  [373.375327]  ? btrfs_ioctl_get_supported_features+0x20/0x20 [btrfs]
  [373.383841]  ? find_held_lock+0x2c/0x110
  [373.389993]  ? lock_release+0x3a9/0x6d0
  [373.395828]  ? mntput_no_expire+0xf7/0xad0
  [373.402083]  ? lock_is_held_type+0xe4/0x140
  [373.408249]  ? vfs_fileattr_set+0x9f0/0x9f0
  [373.414486]  ? selinux_file_ioctl+0x349/0x4e0
  [373.420938]  ? trace_raw_output_lock+0xb4/0xe0
  [373.427442]  ? selinux_inode_getsecctx+0x80/0x80
  [373.434224]  ? lockdep_hardirqs_on+0x7e/0x100
  [373.440660]  ? force_qs_rnp+0x2a0/0x6b0
  [373.446534]  ? lock_is_held_type+0x9b/0x140
  [373.452763]  ? __blkcg_punt_bio_submit+0x1b0/0x1b0
  [373.459732]  ? security_file_ioctl+0x50/0x90
  [373.466089]  __x64_sys_ioctl+0x127/0x190
  [373.472022]  do_syscall_64+0x3b/0x90
  [373.477513]  entry_SYSCALL_64_after_hwframe+0x44/0xae
  [373.484823] RIP: 0033:0x7f8f4af7e2bb
  [373.490493] RSP: 002b:00007ffcbf936178 EFLAGS: 00000246 ORIG_RAX: 0000000000000010
  [373.500197] RAX: ffffffffffffffda RBX: 0000000000000003 RCX: 00007f8f4af7e2bb
  [373.509451] RDX: 00007ffcbf936220 RSI: 00000000c4009420 RDI: 0000000000000003
  [373.518659] RBP: 00007ffcbf93774a R08: 0000000000000013 R09: 00007f8f4b02d4e0
  [373.527872] R10: 00007f8f4ae87740 R11: 0000000000000246 R12: 0000000000000001
  [373.537222] R13: 00007ffcbf936220 R14: 0000000000000000 R15: 0000000000000002
  [373.546506]  </TASK>
  [373.550878] INFO: task btrfs:3146 blocked for more than 123 seconds.
  [373.559383]       Not tainted 5.16.0-rc8 #7
  [373.565748] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
  [373.575748] task:btrfs           state:D stack:    0 pid: 3146 ppid:  2168 flags:0x00000000
  [373.586314] Call Trace:
  [373.590846]  <TASK>
  [373.595121]  __schedule+0xb56/0x4850
  [373.600901]  ? __lock_acquire+0x23db/0x5030
  [373.607176]  ? io_schedule_timeout+0x190/0x190
  [373.613954]  schedule+0xe0/0x270
  [373.619157]  schedule_timeout+0x168/0x220
  [373.625170]  ? usleep_range_state+0x150/0x150
  [373.631653]  ? mark_held_locks+0x9e/0xe0
  [373.637767]  ? do_raw_spin_lock+0x11e/0x250
  [373.643993]  ? lockdep_hardirqs_on_prepare+0x17b/0x410
  [373.651267]  ? _raw_spin_unlock_irq+0x24/0x50
  [373.657677]  ? lockdep_hardirqs_on+0x7e/0x100
  [373.664103]  wait_for_completion+0x163/0x250
  [373.670437]  ? bit_wait_timeout+0x160/0x160
  [373.676585]  btrfs_quota_disable+0x176/0x9a0 [btrfs]
  [373.683979]  ? btrfs_quota_enable+0x12f0/0x12f0 [btrfs]
  [373.691340]  ? down_write+0xd0/0x130
  [373.696880]  ? down_write_killable+0x150/0x150
  [373.703352]  btrfs_ioctl+0x3945/0x71b0 [btrfs]
  [373.710061]  ? find_held_lock+0x2c/0x110
  [373.716192]  ? lock_release+0x3a9/0x6d0
  [373.722047]  ? __handle_mm_fault+0x23cd/0x3050
  [373.728486]  ? btrfs_ioctl_get_supported_features+0x20/0x20 [btrfs]
  [373.737032]  ? set_pte+0x6a/0x90
  [373.742271]  ? do_raw_spin_unlock+0x55/0x1f0
  [373.748506]  ? lock_is_held_type+0xe4/0x140
  [373.754792]  ? vfs_fileattr_set+0x9f0/0x9f0
  [373.761083]  ? selinux_file_ioctl+0x349/0x4e0
  [373.767521]  ? selinux_inode_getsecctx+0x80/0x80
  [373.774247]  ? __up_read+0x182/0x6e0
  [373.780026]  ? count_memcg_events.constprop.0+0x46/0x60
  [373.787281]  ? up_write+0x460/0x460
  [373.792932]  ? security_file_ioctl+0x50/0x90
  [373.799232]  __x64_sys_ioctl+0x127/0x190
  [373.805237]  do_syscall_64+0x3b/0x90
  [373.810947]  entry_SYSCALL_64_after_hwframe+0x44/0xae
  [373.818102] RIP: 0033:0x7f1383ea02bb
  [373.823847] RSP: 002b:00007fffeb4d71f8 EFLAGS: 00000202 ORIG_RAX: 0000000000000010
  [373.833641] RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 00007f1383ea02bb
  [373.842961] RDX: 00007fffeb4d7210 RSI: 00000000c0109428 RDI: 0000000000000003
  [373.852179] RBP: 0000000000000003 R08: 0000000000000003 R09: 0000000000000078
  [373.861408] R10: 00007f1383daec78 R11: 0000000000000202 R12: 00007fffeb4d874a
  [373.870647] R13: 0000000000493099 R14: 0000000000000001 R15: 0000000000000000
  [373.879838]  </TASK>
  [373.884018]
               Showing all locks held in the system:
  [373.894250] 3 locks held by kworker/4:1/58:
  [373.900356] 1 lock held by khungtaskd/63:
  [373.906333]  #0: ffffffff8945ff60 (rcu_read_lock){....}-{1:2}, at: debug_show_all_locks+0x53/0x260
  [373.917307] 3 locks held by kworker/u16:6/103:
  [373.923938]  #0: ffff888127b4f138 ((wq_completion)btrfs-qgroup-rescan){+.+.}-{0:0}, at: process_one_work+0x712/0x1320
  [373.936555]  #1: ffff88810b817dd8 ((work_completion)(&work->normal_work)){+.+.}-{0:0}, at: process_one_work+0x73f/0x1320
  [373.951109]  #2: ffff888102dd4650 (sb_internal#2){.+.+}-{0:0}, at: btrfs_qgroup_rescan_worker+0x1f6/0x10c0 [btrfs]
  [373.964027] 2 locks held by less/1803:
  [373.969982]  #0: ffff88813ed56098 (&tty->ldisc_sem){++++}-{0:0}, at: tty_ldisc_ref_wait+0x24/0x80
  [373.981295]  #1: ffffc90000b3b2e8 (&ldata->atomic_read_lock){+.+.}-{3:3}, at: n_tty_read+0x9e2/0x1060
  [373.992969] 1 lock held by btrfs-transacti/2347:
  [373.999893]  #0: ffff88813d4887a8 (&fs_info->transaction_kthread_mutex){+.+.}-{3:3}, at: transaction_kthread+0xe3/0x3c0 [btrfs]
  [374.015872] 3 locks held by btrfs/3145:
  [374.022298]  #0: ffff888102dd4460 (sb_writers#18){.+.+}-{0:0}, at: btrfs_ioctl_balance+0xc3/0x700 [btrfs]
  [374.034456]  #1: ffff88813d48a0a0 (&fs_info->reclaim_bgs_lock){+.+.}-{3:3}, at: btrfs_balance+0xfe5/0x2d20 [btrfs]
  [374.047646]  #2: ffff88813d488838 (&fs_info->cleaner_mutex){+.+.}-{3:3}, at: btrfs_relocate_block_group+0x354/0x930 [btrfs]
  [374.063295] 4 locks held by btrfs/3146:
  [374.069647]  #0: ffff888102dd4460 (sb_writers#18){.+.+}-{0:0}, at: btrfs_ioctl+0x38b1/0x71b0 [btrfs]
  [374.081601]  #1: ffff88813d488bb8 (&fs_info->subvol_sem){+.+.}-{3:3}, at: btrfs_ioctl+0x38fd/0x71b0 [btrfs]
  [374.094283]  #2: ffff888102dd4650 (sb_internal#2){.+.+}-{0:0}, at: btrfs_quota_disable+0xc8/0x9a0 [btrfs]
  [374.106885]  #3: ffff88813d489800 (&fs_info->qgroup_ioctl_lock){+.+.}-{3:3}, at: btrfs_quota_disable+0xd5/0x9a0 [btrfs]

  [374.126780] =============================================

To avoid the deadlock, wait for the qgroup rescan worker to complete
before starting the transaction for the quota disable ioctl. Clear
BTRFS_FS_QUOTA_ENABLE flag before the wait and the transaction to
request the worker to complete. On transaction start failure, set the
BTRFS_FS_QUOTA_ENABLE flag again. These BTRFS_FS_QUOTA_ENABLE flag
changes can be done safely since the function btrfs_quota_disable is not
called concurrently because of fs_info->subvol_sem.

Also check the BTRFS_FS_QUOTA_ENABLE flag in qgroup_rescan_init to avoid
another qgroup rescan worker to start after the previous qgroup worker
completed.

CC: stable@vger.kernel.org # 5.4+
Suggested-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Shin'ichiro Kawasaki <shinichiro.kawasaki@wdc.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

btrfs: don't start transaction for scrub if the fs is mounted read-only

commit 2d192fc4c1abeb0d04d1c8cd54405ff4a0b0255b upstream.

[BUG]
The following super simple script would crash btrfs at unmount time, if
CONFIG_BTRFS_ASSERT() is set.

 mkfs.btrfs -f $dev
 mount $dev $mnt
 xfs_io -f -c "pwrite 0 4k" $mnt/file
 umount $mnt
 mount -r ro $dev $mnt
 btrfs scrub start -Br $mnt
 umount $mnt

This will trigger the following ASSERT() introduced by commit
0a31daa4b602 ("btrfs: add assertion for empty list of transactions at
late stage of umount").

That patch is definitely not the cause, it just makes enough noise for
developers.

[CAUSE]
We will start transaction for the following call chain during scrub:

  scrub_enumerate_chunks()
  |- btrfs_inc_block_group_ro()
     |- btrfs_join_transaction()

However for RO mount, there is no running transaction at all, thus
btrfs_join_transaction() will start a new transaction.

Furthermore, since it's read-only mount, btrfs_sync_fs() will not call
btrfs_commit_super() to commit the new but empty transaction.

And leads to the ASSERT().

The bug has been there for a long time. Only the new ASSERT() makes it
noisy enough to be noticed.

[FIX]
For read-only scrub on read-only mount, there is no need to start a
transaction nor to allocate new chunks in btrfs_inc_block_group_ro().

Just do extra read-only mount check in btrfs_inc_block_group_ro(), and
if it's read-only, skip all chunk allocation and go inc_block_group_ro()
directly.

CC: stable@vger.kernel.org # 5.4+
Signed-off-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ALSA: hda/realtek: Fix silent output on Gigabyte X570 Aorus Xtreme after reboot from Windows

commit ea3541961376f733373839cc90493aafa8a7f733 upstream.

This commit switches the Gigabyte X570 Aorus Xtreme from using the
ALC1220_FIXUP_CLEVO_P950 to the ALC1220_FIXUP_GB_X570 quirk. This fixes
the no-audio after reboot from windows problem.

BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=205275
Signed-off-by: Christian Lachner <gladiac@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220129113243.93068-4-gladiac@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ALSA: hda/realtek: Fix silent output on Gigabyte X570S Aorus Master (newer chipset)

commit 41a8601302ecbe704ac970552c33dc942300fc37 upstream.

Newer versions of the X570 Master come with a newer revision of the
mainboard chipset - the X570S. These boards have the same ALC1220 codec
but seem to initialize the codec with a different parameter in Coef 0x7
which causes the output audio to be very low. We therefore write a
known-good value to Coef 0x7 to fix that. As the value is the exact same
as on the other X570(non-S) boards the same quirk-function can be shared
between both generations.

This commit adds the Gigabyte X570S Aorus Master to the list of boards
using the ALC1220_FIXUP_GB_X570 quirk. This fixes both, the silent output
and the no-audio after reboot from windows problems.

This work has been tested by the folks over at the level1techs forum here:
https://forum.level1techs.com/t/has-anybody-gotten-audio-working-in-linux-on-aorus-x570-master/154072

Signed-off-by: Christian Lachner <gladiac@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220129113243.93068-3-gladiac@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ALSA: hda/realtek: Add missing fixup-model entry for Gigabyte X570 ALC1220 quirks

commit 63394a16086fc2152869d7902621e2525e14bc40 upstream.

The initial commit of the new Gigabyte X570 ALC1220 quirks lacked the
fixup-model entry in alc882_fixup_models[]. It seemed not to cause any ill
effects but for completeness sake this commit makes up for that.

Signed-off-by: Christian Lachner <gladiac@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220129113243.93068-2-gladiac@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ALSA: hda/realtek: Add quirk for ASUS GU603

commit 94db9cc8f8fa2d5426ce79ec4ca16028f7084224 upstream.

The ASUS GU603 (Zephyrus M16 - SSID 1043:16b2) requires a quirk similar to
other ASUS devices for correctly routing the 4 integrated speakers. This
fixes it by adding a corresponding quirk entry, which connects the bass
speakers to the proper DAC.

Signed-off-by: Albert Geantă <albertgeanta@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220131010523.546386-1-albertgeanta@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ALSA: hda: realtek: Fix race at concurrent COEF updates

commit b837a9f5ab3bdfab9233c9f98a6bef717673a3e5 upstream.

The COEF access is done with two steps: setting the index then read or
write the data.  When multiple COEF accesses are performed
concurrently, the index and data might be paired unexpectedly.
In most cases, this isn't a big problem as the COEF setup is done at
the initialization, but some dynamic changes like the mute LED may hit
such a race.

For avoiding the racy COEF accesses, this patch introduces a new
mutex coef_mutex to alc_spec, and wrap the COEF accessing functions
with it.

Reported-by: Alexander Sergeyev <sergeev917@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220111195229.a77wrpjclqwrx4bx@localhost.localdomain
Link: https://lore.kernel.org/r/20220131075738.24323-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ALSA: hda: Fix UAF of leds class devs at unbinding

commit 549f8ffc7b2f7561bea7f90930b6c5104318e87b upstream.

The LED class devices that are created by HD-audio codec drivers are
registered via devm_led_classdev_register() and associated with the
HD-audio codec device.  Unfortunately, it turned out that the devres
release doesn't work for this case; namely, since the codec resource
release happens before the devm call chain, it triggers a NULL
dereference or a UAF for a stale set_brightness_delay callback.

For fixing the bug, this patch changes the LED class device register
and unregister in a manual manner without devres, keeping the
instances in hda_gen_spec.

Reported-by: Alexander Sergeyev <sergeev917@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220111195229.a77wrpjclqwrx4bx@localhost.localdomain
Link: https://lore.kernel.org/r/20220126145011.16728-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ALSA: usb-audio: Correct quirk for VF0770

commit 4ee02e20893d2f9e951c7888f2284fa608ddaa35 upstream.

This device provides both audio and video. The original quirk added in
commit 48827e1d6af5 ("ALSA: usb-audio: Add quirk for VF0770") used
USB_DEVICE to match the vendor and product ID. Depending on module order,
if snd-usb-audio was asked first, it would match the entire device and
uvcvideo wouldn't get to see it. Change the matching to USB_AUDIO_DEVICE
to restore uvcvideo matching in all cases.

Fixes: 48827e1d6af5 ("ALSA: usb-audio: Add quirk for VF0770")
Reported-by: Jukka Heikintalo <heikintalo.jukka@gmail.com>
Tested-by: Jukka Heikintalo <heikintalo.jukka@gmail.com>
Reported-by: Paweł Susicki <pawel.susicki@gmail.com>
Tested-by: Paweł Susicki <pawel.susicki@gmail.com>
Cc: <stable@vger.kernel.org> # 5.4, 5.10, 5.14, 5.15
Signed-off-by: Jonas Hahnfeld <hahnjo@hahnjo.de>
Link: https://lore.kernel.org/r/20220131183516.61191-1-hahnjo@hahnjo.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ASoC: ops: Reject out of bounds values in snd_soc_put_xr_sx()

commit 4cf28e9ae6e2e11a044be1bcbcfa1b0d8675fe4d upstream.

We don't currently validate that the values being set are within the range
we advertised to userspace as being valid, do so and reject any values
that are out of range.

Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20220124153253.3548853-4-broonie@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ASoC: ops: Reject out of bounds values in snd_soc_put_volsw_sx()

commit 4f1e50d6a9cf9c1b8c859d449b5031cacfa8404e upstream.

We don't currently validate that the values being set are within the range
we advertised to userspace as being valid, do so and reject any values
that are out of range.

Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20220124153253.3548853-3-broonie@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ASoC: ops: Reject out of bounds values in snd_soc_put_volsw()

commit 817f7c9335ec01e0f5e8caffc4f1dcd5e458a4c0 upstream.

We don't currently validate that the values being set are within the range
we advertised to userspace as being valid, do so and reject any values
that are out of range.

Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20220124153253.3548853-2-broonie@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ASoC: hdmi-codec: Fix OOB memory accesses

commit 06feec6005c9d9500cd286ec440aabf8b2ddd94d upstream.

Correct size of iec_status array by changing it to the size of status
array of the struct snd_aes_iec958. This fixes out-of-bounds slab
read accesses made by memcpy() of the hdmi-codec driver. This problem
is reported by KASAN.

Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20220112195039.1329-1-digetx@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

spi: stm32-qspi: Update spi registering

commit e4d63473d3110afd170e6e0e48494d3789d26136 upstream.

Some device driver need to communicate to qspi device during the remove
process, qspi controller must be functional when spi_unregister_master()
is called.

To ensure this, replace devm_spi_register_master() by spi_register_master()
and spi_unregister_master() is called directly in .remove callback before
stopping the qspi controller.

This issue was put in evidence using kernel v5.11 and later
with a spi-nor which supports the software reset feature introduced
by commit d73ee7534cc5 ("mtd: spi-nor: core: perform a Soft Reset on
shutdown")

Fixes: c530cd1d9d5e ("spi: spi-mem: add stm32 qspi controller")

Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: <stable@vger.kernel.org> # 5.8.x
Reviewed-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/20220117121744.29729-1-patrice.chotard@foss.st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ipc/sem: do not sleep with a spin lock held

commit 520ba724061cef59763e2b6f5b26e8387c2e5822 upstream.

We can't call kvfree() with a spin lock held, so defer it.

Link: https://lkml.kernel.org/r/20211223031207.556189-1-chi.minghao@zte.com.cn
Fixes: fc37a3b8b438 ("[PATCH] ipc sem: use kvmalloc for sem_undo allocation")
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Minghao Chi <chi.minghao@zte.com.cn>
Reviewed-by: Shakeel Butt <shakeelb@google.com>
Reviewed-by: Manfred Spraul <manfred@colorfullife.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Yang Guang <cgel.zte@gmail.com>
Cc: Davidlohr Bueso <dbueso@suse.de>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Bhaskar Chowdhury <unixbhaskar@gmail.com>
Cc: Vasily Averin <vvs@virtuozzo.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

audit: improve audit queue handling when "audit=1" on cmdline

commit f26d04331360d42dbd6b58448bd98e4edbfbe1c5 upstream.

When an admin enables audit at early boot via the "audit=1" kernel
command line the audit queue behavior is slightly different; the
audit subsystem goes to greater lengths to avoid dropping records,
which unfortunately can result in problems when the audit daemon is
forcibly stopped for an extended period of time.

This patch makes a number of changes designed to improve the audit
queuing behavior so that leaving the audit daemon in a stopped state
for an extended period does not cause a significant impact to the
system.

- kauditd_send_queue() is now limited to looping through the
  passed queue only once per call.  This not only prevents the
  function from looping indefinitely when records are returned
  to the current queue, it also allows any recovery handling in
  kauditd_thread() to take place when kauditd_send_queue()
  returns.

- Transient netlink send errors seen as -EAGAIN now cause the
  record to be returned to the retry queue instead of going to
  the hold queue.  The intention of the hold queue is to store,
  perhaps for an extended period of time, the events which led
  up to the audit daemon going offline.  The retry queue remains
  a temporary queue intended to protect against transient issues
  between the kernel and the audit daemon.

- The retry queue is now limited by the audit_backlog_limit
  setting, the same as the other queues.  This allows admins
  to bound the size of all of the audit queues on the system.

- kauditd_rehold_skb() now returns records to the end of the
  hold queue to ensure ordering is preserved in the face of
  recent changes to kauditd_send_queue().

Cc: stable@vger.kernel.org
Fixes: 5b52330bbfe63 ("audit: fix auditd/kernel connection state tracking")
Fixes: f4b3ee3c85551 ("audit: improve robustness of the audit queue handling")
Reported-by: Gaosheng Cui <cuigaosheng1@huawei.com>
Tested-by: Gaosheng Cui <cuigaosheng1@huawei.com>
Reviewed-by: Richard Guy Briggs <rgb@redhat.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

selinux: fix double free of cond_list on error paths

commit 186edf7e368c40d06cf727a1ad14698ea67b74ad upstream.

On error path from cond_read_list() and duplicate_policydb_cond_list()
the cond_list_destroy() gets called a second time in caller functions,
resulting in NULL pointer deref.  Fix this by resetting the
cond_list_len to 0 in cond_list_destroy(), making subsequent calls a
noop.

Also consistently reset the cond_list pointer to NULL after freeing.

Cc: stable@vger.kernel.org
Signed-off-by: Vratislav Bendel <vbendel@redhat.com>
[PM: fix line lengths in the description]
Signed-off-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/i915: Disable DSB usage for now

commit 99510e1afb4863a225207146bd988064c5fd0629 upstream.

Turns out the DSB has trouble correctly loading the gamma LUT.
From a cursory look maybe like some entries do not load
properly, or they get loaded with some gibberish. Unfortunately
our current kms_color/etc. tests do not seem to catch this.

I had a brief look at the generated DSB batch and it looked
correct. Tried a few quick tricks like writing the index
register twice/etc. but didn't see any improvement.
Also tried switching to the 10bit gamma mode in case
there is yet another issue with the multi-segment mode, but
even the 10bit mode was showing issues.

Switching to mmio fixes all of it. I suppose one theory is that
maybe the DSB bangs on the LUT too quickly and it can't keep up
and instead some data either gets dropped or corrupted. To confirm
that someone should try to slow down the DSB's progress a bit.
Another thought was that maybe the LUT has crappy dual porting
and you get contention if you try to load it during active
scanout. But why then would the mmio path work, unless it's
just sufficiently slow?

Whatever the case, this is currently busted so let's disable
it until we get to the root of the problem.

Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/3916
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211014181856.17581-2-ville.syrjala@linux.intel.com
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Cc: Mario Kleiner <mario.kleiner.de@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Linux 5.15.21

Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Revert "drm/vc4: hdmi: Make sure the device is powered with CEC" again

This reverts commit fbe1e801bc1fa0a4c34a5284abf6ad0ef887cdfc which is
commit 20b0dfa86bef0e80b41b0e5ac38b92f23b6f27f9 upstream.

It wasn't applied correctly, something went wrong with an attempt to fix
it up again, so just revert the whole thing to be back at a clean state.

Reported-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20220205171238.GA3073350@roeck-us.net
Reported-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Link: https://lore.kernel.org/r/Yf5lNIJnvhP4ajam@kroah.com
Cc: Dave Stevenson <dave.stevenson@raspberrypi.com>
Cc: Maxime Ripard <maxime@cerno.tech>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Revert "drm/vc4: hdmi: Make sure the device is powered with CEC"

This reverts commit d5e81e3a3e0b15964a86c19b5c27397676d6fc1b which is
commit 20b0dfa86bef0e80b41b0e5ac38b92f23b6f27f9 upstream.

It wasn't applied correctly, something went wrong with an attempt to fix
it up again, so just revert the whole thing to be back at a clean state.

Reported-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20220205171238.GA3073350@roeck-us.net
Reported-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Link: https://lore.kernel.org/r/Yf5lNIJnvhP4ajam@kroah.com
Cc: Dave Stevenson <dave.stevenson@raspberrypi.com>
Cc: Maxime Ripard <maxime@cerno.tech>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Linux 5.15.20

Link: https://lore.kernel.org/r/20220204091915.247906930@linuxfoundation.org
Tested-by: Bagas Sanjaya <bagasdotme@gmail.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Shuah Khan <skhan@linuxfoundation.org>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Ron Economos <re@w6rz.net>
Tested-by: Justin M. Forbes <jforbes@fedoraproject.org>
Tested-by: Fox Chen <foxhlchen@gmail.com>
Tested-by: Slade Watkins <slade@sladewatkins.com>
Tested-by: Linux Kernel Functional Testing <lkft@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ovl: fix NULL pointer dereference in copy up warning

commit 4ee7e4a6c9b298da44029ed9ec8ed23ae49cc209 upstream.

This patch is fixing a NULL pointer dereference to get a recently
introduced warning message working.

Fixes: 5b0a414d06c3 ("ovl: fix filattr copy-up failure")
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Cc: <stable@vger.kernel.org> # v5.15
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tcp: add missing tcp_skb_can_collapse() test in tcp_shift_skb_data()

commit b67985be400969578d4d4b17299714c0e5d2c07b upstream.

tcp_shift_skb_data() might collapse three packets into a larger one.

P_A, P_B, P_C  -> P_ABC

Historically, it used a single tcp_skb_can_collapse_to(P_A) call,
because it was enough.

In commit 85712484110d ("tcp: coalesce/collapse must respect MPTCP extensions"),
this call was replaced by a call to tcp_skb_can_collapse(P_A, P_B)

But the now needed test over P_C has been missed.

This probably broke MPTCP.

Then later, commit 9b65b17db723 ("net: avoid double accounting for pure zerocopy skbs")
added an extra condition to tcp_skb_can_collapse(), but the missing call
from tcp_shift_skb_data() is also breaking TCP zerocopy, because P_A and P_C
might have different skb_zcopy_pure() status.

Fixes: 85712484110d ("tcp: coalesce/collapse must respect MPTCP extensions")
Fixes: 9b65b17db723 ("net: avoid double accounting for pure zerocopy skbs")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Mat Martineau <mathew.j.martineau@linux.intel.com>
Cc: Talal Ahmad <talalahmad@google.com>
Cc: Arjun Roy <arjunroy@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Link: https://lore.kernel.org/r/20220201184640.756716-1-eric.dumazet@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

af_packet: fix data-race in packet_setsockopt / packet_setsockopt

commit e42e70ad6ae2ae511a6143d2e8da929366e58bd9 upstream.

When packet_setsockopt( PACKET_FANOUT_DATA ) reads po->fanout,
no lock is held, meaning that another thread can change po->fanout.

Given that po->fanout can only be set once during the socket lifetime
(it is only cleared from fanout_release()), we can use
READ_ONCE()/WRITE_ONCE() to document the race.

BUG: KCSAN: data-race in packet_setsockopt / packet_setsockopt

write to 0xffff88813ae8e300 of 8 bytes by task 14653 on cpu 0:
 fanout_add net/packet/af_packet.c:1791 [inline]
 packet_setsockopt+0x22fe/0x24a0 net/packet/af_packet.c:3931
 __sys_setsockopt+0x209/0x2a0 net/socket.c:2180
 __do_sys_setsockopt net/socket.c:2191 [inline]
 __se_sys_setsockopt net/socket.c:2188 [inline]
 __x64_sys_setsockopt+0x62/0x70 net/socket.c:2188
 do_syscall_x64 arch/x86/entry/common.c:50 [inline]
 do_syscall_64+0x44/0xd0 arch/x86/entry/common.c:80
 entry_SYSCALL_64_after_hwframe+0x44/0xae

read to 0xffff88813ae8e300 of 8 bytes by task 14654 on cpu 1:
 packet_setsockopt+0x691/0x24a0 net/packet/af_packet.c:3935
 __sys_setsockopt+0x209/0x2a0 net/socket.c:2180
 __do_sys_setsockopt net/socket.c:2191 [inline]
 __se_sys_setsockopt net/socket.c:2188 [inline]
 __x64_sys_setsockopt+0x62/0x70 net/socket.c:2188
 do_syscall_x64 arch/x86/entry/common.c:50 [inline]
 do_syscall_64+0x44/0xd0 arch/x86/entry/common.c:80
 entry_SYSCALL_64_after_hwframe+0x44/0xae

value changed: 0x0000000000000000 -> 0xffff888106f8c000

Reported by Kernel Concurrency Sanitizer on:
CPU: 1 PID: 14654 Comm: syz-executor.3 Not tainted 5.16.0-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011

Fixes: 47dceb8ecdc1 ("packet: add classic BPF fanout mode")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Link: https://lore.kernel.org/r/20220201022358.330621-1-eric.dumazet@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

e1000e: Handshake with CSME starts from ADL platforms

commit cad014b7b5a6897d8c4fad13e2888978bfb7a53f upstream.

Handshake with CSME/AMT on none provisioned platforms during S0ix flow
is not supported on TGL platform and can cause to HW unit hang. Update
the handshake with CSME flow to start from the ADL platform.

Fixes: 3e55d231716e ("e1000e: Add handshake with the CSME to support S0ix")
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Nechama Kraus <nechamax.kraus@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

cpuset: Fix the bug that subpart_cpus updated wrongly in update_cpumask()

commit c80d401c52a2d1baf2a5afeb06f0ffe678e56d23 upstream.

subparts_cpus should be limited as a subset of cpus_allowed, but it is
updated wrongly by using cpumask_andnot(). Use cpumask_and() instead to
fix it.

Fixes: ee8dde0cd2ce ("cpuset: Add new v2 cpuset.sched.partition flag")
Signed-off-by: Tianchen Ding <dtcccc@linux.alibaba.com>
Reviewed-by: Waiman Long <longman@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

rtnetlink: make sure to refresh master_dev/m_ops in __rtnl_newlink()

commit c6f6f2444bdbe0079e41914a35081530d0409963 upstream.

While looking at one unrelated syzbot bug, I found the replay logic
in __rtnl_newlink() to potentially trigger use-after-free.

It is better to clear master_dev and m_ops inside the loop,
in case we have to replay it.

Fixes: ba7d49b1f0f8 ("rtnetlink: provide api for getting and setting slave info")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jiri Pirko <jiri@nvidia.com>
Link: https://lore.kernel.org/r/20220201012106.216495-1-eric.dumazet@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: sched: fix use-after-free in tc_new_tfilter()

commit 04c2a47ffb13c29778e2a14e414ad4cb5a5db4b5 upstream.

Whenever tc_new_tfilter() jumps back to replay: label,
we need to make sure @q and @chain local variables are cleared again,
or risk use-after-free as in [1]

For consistency, apply the same fix in tc_ctl_chain()

BUG: KASAN: use-after-free in mini_qdisc_pair_swap+0x1b9/0x1f0 net/sched/sch_generic.c:1581
Write of size 8 at addr ffff8880985c4b08 by task syz-executor.4/1945

CPU: 0 PID: 1945 Comm: syz-executor.4 Not tainted 5.17.0-rc1-syzkaller-00495-gff58831fa02d #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
 <TASK>
 __dump_stack lib/dump_stack.c:88 [inline]
 dump_stack_lvl+0xcd/0x134 lib/dump_stack.c:106
 print_address_description.constprop.0.cold+0x8d/0x336 mm/kasan/report.c:255
 __kasan_report mm/kasan/report.c:442 [inline]
 kasan_report.cold+0x83/0xdf mm/kasan/report.c:459
 mini_qdisc_pair_swap+0x1b9/0x1f0 net/sched/sch_generic.c:1581
 tcf_chain_head_change_item net/sched/cls_api.c:372 [inline]
 tcf_chain0_head_change.isra.0+0xb9/0x120 net/sched/cls_api.c:386
 tcf_chain_tp_insert net/sched/cls_api.c:1657 [inline]
 tcf_chain_tp_insert_unique net/sched/cls_api.c:1707 [inline]
 tc_new_tfilter+0x1e67/0x2350 net/sched/cls_api.c:2086
 rtnetlink_rcv_msg+0x80d/0xb80 net/core/rtnetlink.c:5583
 netlink_rcv_skb+0x153/0x420 net/netlink/af_netlink.c:2494
 netlink_unicast_kernel net/netlink/af_netlink.c:1317 [inline]
 netlink_unicast+0x539/0x7e0 net/netlink/af_netlink.c:1343
 netlink_sendmsg+0x904/0xe00 net/netlink/af_netlink.c:1919
 sock_sendmsg_nosec net/socket.c:705 [inline]
 sock_sendmsg+0xcf/0x120 net/socket.c:725
 ____sys_sendmsg+0x331/0x810 net/socket.c:2413
 ___sys_sendmsg+0xf3/0x170 net/socket.c:2467
 __sys_sendmmsg+0x195/0x470 net/socket.c:2553
 __do_sys_sendmmsg net/socket.c:2582 [inline]
 __se_sys_sendmmsg net/socket.c:2579 [inline]
 __x64_sys_sendmmsg+0x99/0x100 net/socket.c:2579
 do_syscall_x64 arch/x86/entry/common.c:50 [inline]
 do_syscall_64+0x35/0xb0 arch/x86/entry/common.c:80
 entry_SYSCALL_64_after_hwframe+0x44/0xae
RIP: 0033:0x7f2647172059
Code: ff ff c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 40 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 b8 ff ff ff f7 d8 64 89 01 48
RSP: 002b:00007f2645aa5168 EFLAGS: 00000246 ORIG_RAX: 0000000000000133
RAX: ffffffffffffffda RBX: 00007f2647285100 RCX: 00007f2647172059
RDX: 040000000000009f RSI: 00000000200002c0 RDI: 0000000000000006
RBP: 00007f26471cc08d R08: 0000000000000000 R09: 0000000000000000
R10: 9e00000000000000 R11: 0000000000000246 R12: 0000000000000000
R13: 00007fffb3f7f02f R14: 00007f2645aa5300 R15: 0000000000022000
 </TASK>

Allocated by task 1944:
 kasan_save_stack+0x1e/0x40 mm/kasan/common.c:38
 kasan_set_track mm/kasan/common.c:45 [inline]
 set_alloc_info mm/kasan/common.c:436 [inline]
 ____kasan_kmalloc mm/kasan/common.c:515 [inline]
 ____kasan_kmalloc mm/kasan/common.c:474 [inline]
 __kasan_kmalloc+0xa9/0xd0 mm/kasan/common.c:524
 kmalloc_node include/linux/slab.h:604 [inline]
 kzalloc_node include/linux/slab.h:726 [inline]
 qdisc_alloc+0xac/0xa10 net/sched/sch_generic.c:941
 qdisc_create.constprop.0+0xce/0x10f0 net/sched/sch_api.c:1211
 tc_modify_qdisc+0x4c5/0x1980 net/sched/sch_api.c:1660
 rtnetlink_rcv_msg+0x413/0xb80 net/core/rtnetlink.c:5592
 netlink_rcv_skb+0x153/0x420 net/netlink/af_netlink.c:2494
 netlink_unicast_kernel net/netlink/af_netlink.c:1317 [inline]
 netlink_unicast+0x539/0x7e0 net/netlink/af_netlink.c:1343
 netlink_sendmsg+0x904/0xe00 net/netlink/af_netlink.c:1919
 sock_sendmsg_nosec net/socket.c:705 [inline]
 sock_sendmsg+0xcf/0x120 net/socket.c:725
 ____sys_sendmsg+0x331/0x810 net/socket.c:2413
 ___sys_sendmsg+0xf3/0x170 net/socket.c:2467
 __sys_sendmmsg+0x195/0x470 net/socket.c:2553
 __do_sys_sendmmsg net/socket.c:2582 [inline]
 __se_sys_sendmmsg net/socket.c:2579 [inline]
 __x64_sys_sendmmsg+0x99/0x100 net/socket.c:2579
 do_syscall_x64 arch/x86/entry/common.c:50 [inline]
 do_syscall_64+0x35/0xb0 arch/x86/entry/common.c:80
 entry_SYSCALL_64_after_hwframe+0x44/0xae

Freed by task 3609:
 kasan_save_stack+0x1e/0x40 mm/kasan/common.c:38
 kasan_set_track+0x21/0x30 mm/kasan/common.c:45
 kasan_set_free_info+0x20/0x30 mm/kasan/generic.c:370
 ____kasan_slab_free mm/kasan/common.c:366 [inline]
 ____kasan_slab_free+0x130/0x160 mm/kasan/common.c:328
 kasan_slab_free include/linux/kasan.h:236 [inline]
 slab_free_hook mm/slub.c:1728 [inline]
 slab_free_freelist_hook+0x8b/0x1c0 mm/slub.c:1754
 slab_free mm/slub.c:3509 [inline]
 kfree+0xcb/0x280 mm/slub.c:4562
 rcu_do_batch kernel/rcu/tree.c:2527 [inline]
 rcu_core+0x7b8/0x1540 kernel/rcu/tree.c:2778
 __do_softirq+0x29b/0x9c2 kernel/softirq.c:558

Last potentially related work creation:
 kasan_save_stack+0x1e/0x40 mm/kasan/common.c:38
 __kasan_record_aux_stack+0xbe/0xd0 mm/kasan/generic.c:348
 __call_rcu kernel/rcu/tree.c:3026 [inline]
 call_rcu+0xb1/0x740 kernel/rcu/tree.c:3106
 qdisc_put_unlocked+0x6f/0x90 net/sched/sch_generic.c:1109
 tcf_block_release+0x86/0x90 net/sched/cls_api.c:1238
 tc_new_tfilter+0xc0d/0x2350 net/sched/cls_api.c:2148
 rtnetlink_rcv_msg+0x80d/0xb80 net/core/rtnetlink.c:5583
 netlink_rcv_skb+0x153/0x420 net/netlink/af_netlink.c:2494
 netlink_unicast_kernel net/netlink/af_netlink.c:1317 [inline]
 netlink_unicast+0x539/0x7e0 net/netlink/af_netlink.c:1343
 netlink_sendmsg+0x904/0xe00 net/netlink/af_netlink.c:1919
 sock_sendmsg_nosec net/socket.c:705 [inline]
 sock_sendmsg+0xcf/0x120 net/socket.c:725
 ____sys_sendmsg+0x331/0x810 net/socket.c:2413
 ___sys_sendmsg+0xf3/0x170 net/socket.c:2467
 __sys_sendmmsg+0x195/0x470 net/socket.c:2553
 __do_sys_sendmmsg net/socket.c:2582 [inline]
 __se_sys_sendmmsg net/socket.c:2579 [inline]
 __x64_sys_sendmmsg+0x99/0x100 net/socket.c:2579
 do_syscall_x64 arch/x86/entry/common.c:50 [inline]
 do_syscall_64+0x35/0xb0 arch/x86/entry/common.c:80
 entry_SYSCALL_64_after_hwframe+0x44/0xae

The buggy address belongs to the object at ffff8880985c4800
 which belongs to the cache kmalloc-1k of size 1024
The buggy address is located 776 bytes inside of
 1024-byte region [ffff8880985c4800, ffff8880985c4c00)
The buggy address belongs to the page:
page:ffffea0002617000 refcount:1 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x985c0
head:ffffea0002617000 order:3 compound_mapcount:0 compound_pincount:0
flags: 0xfff00000010200(slab|head|node=0|zone=1|lastcpupid=0x7ff)
raw: 00fff00000010200 0000000000000000 dead000000000122 ffff888010c41dc0
raw: 0000000000000000 0000000000100010 00000001ffffffff 0000000000000000
page dumped because: kasan: bad access detected
page_owner tracks the page as allocated
page last allocated via order 3, migratetype Unmovable, gfp_mask 0x1d20c0(__GFP_IO|__GFP_FS|__GFP_NOWARN|__GFP_NORETRY|__GFP_COMP|__GFP_NOMEMALLOC|__GFP_HARDWALL), pid 1941, ts 1038999441284, free_ts 1033444432829
 prep_new_page mm/page_alloc.c:2434 [inline]
 get_page_from_freelist+0xa72/0x2f50 mm/page_alloc.c:4165
 __alloc_pages+0x1b2/0x500 mm/page_alloc.c:5389
 alloc_pages+0x1aa/0x310 mm/mempolicy.c:2271
 alloc_slab_page mm/slub.c:1799 [inline]
 allocate_slab mm/slub.c:1944 [inline]
 new_slab+0x28a/0x3b0 mm/slub.c:2004
 ___slab_alloc+0x87c/0xe90 mm/slub.c:3018
 __slab_alloc.constprop.0+0x4d/0xa0 mm/slub.c:3105
 slab_alloc_node mm/slub.c:3196 [inline]
 slab_alloc mm/slub.c:3238 [inline]
 __kmalloc+0x2fb/0x340 mm/slub.c:4420
 kmalloc include/linux/slab.h:586 [inline]
 kzalloc include/linux/slab.h:715 [inline]
 __register_sysctl_table+0x112/0x1090 fs/proc/proc_sysctl.c:1335
 neigh_sysctl_register+0x2c8/0x5e0 net/core/neighbour.c:3787
 devinet_sysctl_register+0xb1/0x230 net/ipv4/devinet.c:2618
 inetdev_init+0x286/0x580 net/ipv4/devinet.c:278
 inetdev_event+0xa8a/0x15d0 net/ipv4/devinet.c:1532
 notifier_call_chain+0xb5/0x200 kernel/notifier.c:84
 call_netdevice_notifiers_info+0xb5/0x130 net/core/dev.c:1919
 call_netdevice_notifiers_extack net/core/dev.c:1931 [inline]
 call_netdevice_notifiers net/core/dev.c:1945 [inline]
 register_netdevice+0x1073/0x1500 net/core/dev.c:9698
 veth_newlink+0x59c/0xa90 drivers/net/veth.c:1722
page last free stack trace:
 reset_page_owner include/linux/page_owner.h:24 [inline]
 free_pages_prepare mm/page_alloc.c:1352 [inline]
 free_pcp_prepare+0x374/0x870 mm/page_alloc.c:1404
 free_unref_page_prepare mm/page_alloc.c:3325 [inline]
 free_unref_page+0x19/0x690 mm/page_alloc.c:3404
 release_pages+0x748/0x1220 mm/swap.c:956
 tlb_batch_pages_flush mm/mmu_gather.c:50 [inline]
 tlb_flush_mmu_free mm/mmu_gather.c:243 [inline]
 tlb_flush_mmu+0xe9/0x6b0 mm/mmu_gather.c:250
 zap_pte_range mm/memory.c:1441 [inline]
 zap_pmd_range mm/memory.c:1490 [inline]
 zap_pud_range mm/memory.c:1519 [inline]
 zap_p4d_range mm/memory.c:1540 [inline]
 unmap_page_range+0x1d1d/0x2a30 mm/memory.c:1561
 unmap_single_vma+0x198/0x310 mm/memory.c:1606
 unmap_vmas+0x16b/0x2f0 mm/memory.c:1638
 exit_mmap+0x201/0x670 mm/mmap.c:3178
 __mmput+0x122/0x4b0 kernel/fork.c:1114
 mmput+0x56/0x60 kernel/fork.c:1135
 exit_mm kernel/exit.c:507 [inline]
 do_exit+0xa3c/0x2a30 kernel/exit.c:793
 do_group_exit+0xd2/0x2f0 kernel/exit.c:935
 __do_sys_exit_group kernel/exit.c:946 [inline]
 __se_sys_exit_group kernel/exit.c:944 [inline]
 __x64_sys_exit_group+0x3a/0x50 kernel/exit.c:944
 do_syscall_x64 arch/x86/entry/common.c:50 [inline]
 do_syscall_64+0x35/0xb0 arch/x86/entry/common.c:80
 entry_SYSCALL_64_after_hwframe+0x44/0xae

Memory state around the buggy address:
 ffff8880985c4a00: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
 ffff8880985c4a80: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
>ffff8880985c4b00: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
                      ^
 ffff8880985c4b80: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
 ffff8880985c4c00: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc

Fixes: 470502de5bdb ("net: sched: unlock rules update API")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Vlad Buslov <vladbu@mellanox.com>
Cc: Jiri Pirko <jiri@mellanox.com>
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Link: https://lore.kernel.org/r/20220131172018.3704490-1-eric.dumazet@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

fanotify: Fix stale file descriptor in copy_event_to_user()

commit ee12595147ac1fbfb5bcb23837e26dd58d94b15d upstream.

This code calls fd_install() which gives the userspace access to the fd.
Then if copy_info_records_to_user() fails it calls put_unused_fd(fd) but
that will not release it and leads to a stale entry in the file
descriptor table.

Generally you can't trust the fd after a call to fd_install().  The fix
is to delay the fd_install() until everything else has succeeded.

Fortunately it requires CAP_SYS_ADMIN to reach this code so the security
impact is less.

Fixes: f644bc449b37 ("fanotify: fix copy_event_to_user() fid error clean up")
Link: https://lore.kernel.org/r/20220128195656.GA26981@kili
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Mathias Krause <minipli@grsecurity.net>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: amd-xgbe: Fix skb data length underflow

commit 5aac9108a180fc06e28d4e7fb00247ce603b72ee upstream.

There will be BUG_ON() triggered in include/linux/skbuff.h leading to
intermittent kernel panic, when the skb length underflow is detected.

Fix this by dropping the packet if such length underflows are seen
because of inconsistencies in the hardware descriptors.

Fixes: 622c36f143fc ("amd-xgbe: Fix jumbo MTU processing on newer hardware")
Suggested-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Acked-by: Tom Lendacky <thomas.lendacky@amd.com>
Link: https://lore.kernel.org/r/20220127092003.2812745-1-Shyam-sundar.S-k@amd.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: amd-xgbe: ensure to reset the tx_timer_active flag

commit 7674b7b559b683478c3832527c59bceb169e701d upstream.

Ensure to reset the tx_timer_active flag in xgbe_stop(),
otherwise a port restart may result in tx timeout due to
uncleared flag.

Fixes: c635eaacbf77 ("amd-xgbe: Remove Tx coalescing")
Co-developed-by: Sudheesh Mavila <sudheesh.mavila@amd.com>
Signed-off-by: Sudheesh Mavila <sudheesh.mavila@amd.com>
Signed-off-by: Raju Rangoju <Raju.Rangoju@amd.com>
Acked-by: Tom Lendacky <thomas.lendacky@amd.com>
Link: https://lore.kernel.org/r/20220127060222.453371-1-Raju.Rangoju@amd.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

i40e: Fix reset path while removing the driver

commit 6533e558c6505e94c3e0ed4281ed5e31ec985f4d upstream.

Fix the crash in kernel while dereferencing the NULL pointer,
when the driver is unloaded and simultaneously the VSI rings
are being stopped.

The hardware requires 50msec in order to finish RX queues
disable. For this purpose the driver spins in mdelay function
for the operation to be completed.

For example changing number of queues which requires reset would
fail in the following call stack:

1) i40e_prep_for_reset
2) i40e_pf_quiesce_all_vsi
3) i40e_quiesce_vsi
4) i40e_vsi_close
5) i40e_down
6) i40e_vsi_stop_rings
7) i40e_vsi_control_rx -> disable requires the delay of 50msecs
8) continue back in i40e_down function where
   i40e_clean_tx_ring(vsi->tx_rings[i]) is going to crash

When the driver was spinning vsi_release called
i40e_vsi_free_arrays where the vsi->tx_rings resources
were freed and the pointer was set to NULL.

Fixes: 5b6d4a7f20b0 ("i40e: Fix crash during removing i40e driver")
Signed-off-by: Slawomir Laba <slawomirx.laba@intel.com>
Signed-off-by: Sylwester Dziedziuch <sylwesterx.dziedziuch@intel.com>
Signed-off-by: Karen Sornek <karen.sornek@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

i40e: Fix reset bw limit when DCB enabled with 1 TC

commit 3d2504663c41104b4359a15f35670cfa82de1bbf upstream.

There was an AQ error I40E_AQ_RC_EINVAL when trying
to reset bw limit as part of bw allocation setup.
This was caused by trying to reset bw limit with
DCB enabled. Bw limit should not be reset when
DCB is enabled. The code was relying on the pf->flags
to check if DCB is enabled but if only 1 TC is available
this flag will not be set even though DCB is enabled.
Add a check for number of TC and if it is 1
don't try to reset bw limit even if pf->flags shows
DCB as disabled.

Fixes: fa38e30ac73f ("i40e: Fix for Tx timeouts when interface is brought up if DCB is enabled")
Suggested-by: Alexander Lobakin <alexandr.lobakin@intel.com> # Flatten the condition
Signed-off-by: Sylwester Dziedziuch <sylwesterx.dziedziuch@intel.com>
Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Reviewed-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Tested-by: Imam Hassan Reza Biswas <imam.hassan.reza.biswas@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ipheth: fix EOVERFLOW in ipheth_rcvbulk_callback

commit 63e4b45c82ed1bde979da7052229a4229ce9cabf upstream.

When rx_buf is allocated we need to account for IPHETH_IP_ALIGN,
which reduces the usable size by 2 bytes. Otherwise we have 1512
bytes usable instead of 1514, and if we receive more than 1512
bytes, ipheth_rcvbulk_callback is called with status -EOVERFLOW,
after which the driver malfunctiones and all communication stops.

Resolves ipheth 2-1:4.2: ipheth_rcvbulk_callback: urb status: -75

Fixes: f33d9e2b48a3 ("usbnet: ipheth: fix connectivity with iOS 14")
Signed-off-by: Georgi Valkov <gvalkov@abv.bg>
Tested-by: Jan Kiszka <jan.kiszka@siemens.com>
Link: https://lore.kernel.org/all/B60B8A4B-92A0-49B3-805D-809A2433B46C@abv.bg/
Link: https://lore.kernel.org/all/24851bd2769434a5fc24730dce8e8a984c5a4505.1643699778.git.jan.kiszka@siemens.com/
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net/mlx5: E-Switch, Fix uninitialized variable modact

commit d8e5883d694bb053b19c4142a2d1f43a34f6fe2c upstream.

The variable modact is not initialized before used in command
modify header allocation which can cause command to fail.

Fix by initializing modact with zeros.

Addresses-Coverity: ("Uninitialized scalar variable")
Fixes: 8f1e0b97cc70 ("net/mlx5: E-Switch, Mark miss packets with new chain id mapping")
Signed-off-by: Maor Dickman <maord@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net/mlx5: Bridge, Fix devlink deadlock on net namespace deletion

commit 880b517691908fb753019b9b27cd082e7617debd upstream.

When changing mode to switchdev, rep bridge init registered to netdevice
notifier holds the devlink lock and then takes pernet_ops_rwsem.
At that time deleting a netns holds pernet_ops_rwsem and then takes
the devlink lock.

Example sequence is:
$ ip netns add foo
$ devlink dev eswitch set pci/0000:00:08.0 mode switchdev &
$ ip netns del foo

deleting netns trace:

[ 1185.365555]  ? devlink_pernet_pre_exit+0x74/0x1c0
[ 1185.368331]  ? mutex_lock_io_nested+0x13f0/0x13f0
[ 1185.370984]  ? xt_find_table+0x40/0x100
[ 1185.373244]  ? __mutex_lock+0x24a/0x15a0
[ 1185.375494]  ? net_generic+0xa0/0x1c0
[ 1185.376844]  ? wait_for_completion_io+0x280/0x280
[ 1185.377767]  ? devlink_pernet_pre_exit+0x74/0x1c0
[ 1185.378686]  devlink_pernet_pre_exit+0x74/0x1c0
[ 1185.379579]  ? devlink_nl_cmd_get_dumpit+0x3a0/0x3a0
[ 1185.380557]  ? xt_find_table+0xda/0x100
[ 1185.381367]  cleanup_net+0x372/0x8e0

changing mode to switchdev trace:

[ 1185.411267]  down_write+0x13a/0x150
[ 1185.412029]  ? down_write_killable+0x180/0x180
[ 1185.413005]  register_netdevice_notifier+0x1e/0x210
[ 1185.414000]  mlx5e_rep_bridge_init+0x181/0x360 [mlx5_core]
[ 1185.415243]  mlx5e_uplink_rep_enable+0x269/0x480 [mlx5_core]
[ 1185.416464]  ? mlx5e_uplink_rep_disable+0x210/0x210 [mlx5_core]
[ 1185.417749]  mlx5e_attach_netdev+0x232/0x400 [mlx5_core]
[ 1185.418906]  mlx5e_netdev_attach_profile+0x15b/0x1e0 [mlx5_core]
[ 1185.420172]  mlx5e_netdev_change_profile+0x15a/0x1d0 [mlx5_core]
[ 1185.421459]  mlx5e_vport_rep_load+0x557/0x780 [mlx5_core]
[ 1185.422624]  ? mlx5e_stats_grp_vport_rep_num_stats+0x10/0x10 [mlx5_core]
[ 1185.424006]  mlx5_esw_offloads_rep_load+0xdb/0x190 [mlx5_core]
[ 1185.425277]  esw_offloads_enable+0xd74/0x14a0 [mlx5_core]

Fix this by registering rep bridges for per net netdev notifier
instead of global one, which operats on the net namespace without holding
the pernet_ops_rwsem.

Fixes: 19e9bfa044f3 ("net/mlx5: Bridge, add offload infrastructure")
Signed-off-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>