Olof Johansson [Thu, 27 Jun 2019 02:19:58 +0000 (19:19 -0700)]
Merge tag 'v5.2-next-dts64' of https://git./linux/kernel/git/matthias.bgg/linux into arm/dt
- convert arm boads to json-schema
mt8183:
- add base SoC and evaluation board
- add cpacity-dmips-mhz
- add pinctrl, auxadc, spi, and efuse nodes
* tag 'v5.2-next-dts64' of https://git.kernel.org/pub/scm/linux/kernel/git/matthias.bgg/linux:
arm64: dts: mt8183: add efuse and Mediatek Chip id node to read
arm64: dts: mt8183: add spi node
arm64: dts: mt8183: Add auxadc device node
arm64: dts: mt8183: add pinctrl device node
arm64: dts: mt8183: add capacity-dmips-mhz
arm64: dts: Add Mediatek SoC MT8183 and evaluation board dts and Makefile
dt-bindings: arm: Convert MediaTek board/soc bindings to json-schema
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Tue, 25 Jun 2019 12:52:25 +0000 (05:52 -0700)]
Merge tag 'amlogic-dt64' of https://git./linux/kernel/git/khilman/linux-amlogic into arm/dt
arm64: dts: Amlogic updates for v5.3
Highlights:
- new SoC: S922X (G12B family, A73/A53 big.LITTLE)
- new board: Hardkernel odroid-N2 (SoC: G12B S922X)
- add/use ethernet PHY interrupt/reset lines
- G12A: add/enable audio, PWM, IR, i2c, SD/eMMC, WiFi, bluetooth, network
- gxbb-vega-s95 board: fix WiFi/BT, enable more peripherals
* tag 'amlogic-dt64' of https://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic: (79 commits)
arm64: dts: meson: g12a: x96-max: add the Ethernet PHY interrupt line
arm64: dts: meson: g12b: odroid-n2: add the Ethernet PHY interrupt line
arm64: dts: meson: g12b: odroid-n2: add the Ethernet PHY reset line
arm64: dts: meson: use the generic Ethernet PHY reset GPIO bindings
arm64: dts: meson: g12a: x96-max: fix the Ethernet PHY reset line
arm64: dts: meson: g12a: sort sdio nodes correctly
arm64: dts: meson-g12a-x96-max: add sound card
arm64: dts: meson-g12b-odroid-n2: add sound card
arm64: dts: meson: sei510: add sound card
arm64: dts: meson: sei510: add max98357a DAC
ASoC: meson: add tohdmitx DT bindings
arm64: dts: meson: g12a: add the GPIO interrupt controller
arm64: dts: meson-g12a-x96-max: bump bluetooth bus speed to 2Mbaud/s
arm64: dts: meson-g12a-sei510: bump bluetooth bus speed to 2Mbaud/s
arm64: dts: meson-g12a-x96-max: add 32k clock to bluetooth node
arm64: dts: meson-g12a-sei510: add 32k clock to bluetooth node
arm64: dts: meson-g12a-sei510: Enable Wifi SDIO module
arm64: dts: meson-g12a-x96-max: Enable Wifi SDIO Module
arm64: dts: meson-g12a-x96-max: add support for sdcard and emmc
arm64: dts: meson: g12a: add SDIO controller
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Tue, 25 Jun 2019 11:52:55 +0000 (04:52 -0700)]
Merge tag 'imx-dt64-5.3' of git://git./linux/kernel/git/shawnguo/linux into arm/dt
i.MX arm64 device tree changes for 5.3:
- Add i.MX8MQ based Librem5 devkit support.
- Add SNVS power key support for i.MX8MQ and i.MX8MM.
- Add GPIO alias for imx8mq and i.MX8QXP.
- A series from Daniel Baluta to add SAI devices and enable audio
support for imx8mm-evk board.
- Add DDR performance monitor unit support for i.MX8QXP.
- Add irqsteer interrupt controller device for i.MX8MQ SoC.
- Add CPU speed grading and all OPPs for i.MX8MM and i.MX8MQ.
- Add OCOTP device node for i.MX8QXP.
- Various device addition for LS1028A: SATA, qDMA, USB, Mali DP500 and
temperature sensor.
- Random minor coding style improvements.
* tag 'imx-dt64-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (32 commits)
arm64: dts: librem5: enable the SNVS power key
arm64: dts: librem5: Limit the USB to 5V
arm64: dts: imx8qxp: added ddr performance monitor nodes
arm64: dts: imx8qxp: sort LSIO subsystem devices
arm64: dts: imx8qxp: sort alias alphabetically
arm64: dts: imx8qxp: Add lsio_mu13 node
arm64: dts: imx8mm-evk: Enable audio codec wm8524
arm64: dts: fsl: librem5: Add a device tree for the Librem5 devkit
arm64: dts: fsl: ls1028a: Add qDMA node
arm64: dts: imx8mm: Enable SNVS power key according to board design
arm64: dts: imx8mq-evk: Enable SNVS power key
arm64: dts: ls1028a: add crypto node
arm64: dts: ls1028a: Add temperature sensor node
arm64: dts: imx8mm: Move gic node into soc node
arm64: dts: imx8mm: Move usbphy out of soc node
arm64: dts: imx8mm: Pass the 'ranges' property
arm64: dts: imx8mm: Pass a unit name for the 'soc' node
arm64: dts: fsl: imx8mq: add the snvs power key node
arm64: dts: ls1028a: fix watchdog device node
arm64: dts: ls1028a: Enable sata.
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Tue, 25 Jun 2019 11:52:17 +0000 (04:52 -0700)]
Merge tag 'imx-dt-5.3' of git://git./linux/kernel/git/shawnguo/linux into arm/dt
i.MX arm32 DT changes for 5.3:
- New board support: iMX6-based Kontron SMARC-sAMX6i, i.MX7D based
Meerkat96 board, and NXP LS1021A-TSN board.
- A series from Andrey Smirnov to update vf610-zii-dev and
imx7d-zii-rpu2 board, fixing UART2 pin assignment and stdout-path,
adding QSPI device, and dropping unused pinmux.
- Update imx6sl and imx6qdl device tree to assign corresponding clocks
instead of dummy clock.
- Update i.MX6/7 boards from NXP to assign corresponding power supply
for LDOs.
- Update i.MX6/7 device trees to enable SNVS poweroff key support
according to board design.
- Update coresight DT binding for i.MX7 according to consolidations
for CoreSight replicator and funnel.
- A series from Marek Vasut to update M53Menlo board on various devices
like UART, USB, ethernet PHY, GPIOs etc.
- Enable USBOTG support for imx7ulp and evk board.
- A series from Peter Robinson to update imx6sx-udoo board, switching
to SPDX License Identifier, enabling I2C devices and bluetooth
support.
- Add video capture support for i.MX53 and imx53-smd board.
- Add PXP device for i.MX6UL.
- Other random small updates on various boards.
* tag 'imx-dt-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (46 commits)
ARM: dts: imx7ulp-evk: enable USBOTG1 support
ARM: dts: imx7ulp: add imx7ulp USBOTG1 support
ARM: dts: imx6qdl-kontron-samx6i: add Kontron SMARC SoM Support
ARM: dts: imx6qdl-kontron-samx6i: Add iMX6-based Kontron SMARC-sAMX6i module
ARM: dts: imx7d-zii-rpu2: Drop unused pinmux entries
ARM: dts: imx7d-zii-rpu2: Fix incorrrect 'stdout-path'
ARM: dts: Add support for 96Boards Meerkat96 board
ARM: dts: imx6ul: Add PXP node
ARM: dts: imx6sll: Enable SNVS poweroff according to board design
ARM: dts: imx7s: Enable SNVS power key according to board design
ARM: dts: imx6sll: Enable SNVS power key according to board design
ARM: dts: imx6ul: Enable SNVS power key according to board design
ARM: dts: imx6sx: Enable SNVS power key according to board design
ARM: dts: imx6qdl: Enable SNVS power key according to board design
ARM: dts: imx53: Bind CPLD on M53Menlo
ARM: dts: Introduce the NXP LS1021A-TSN board
ARM: dts: imx6ull-colibri: enable UHS-I for USDHC1
ARM: dts: imx7d: Update cpufreq OPP table
ARM: dts: imx6sx-udoo-neo: add bluetooth config to uart3
ARM: dts: imx6sx-udoo-neo: enable i2c-2 and i2c-4 for onboard sensors
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Tue, 25 Jun 2019 11:51:42 +0000 (04:51 -0700)]
Merge tag 'imx-dt-clkdep-5.3' of git://git./linux/kernel/git/shawnguo/linux into arm/dt
i.MX DT changes with new clock for 5.3:
- This is a set of device tree changes with new clocks - adding
clock info for i.MX8 GPIO and SNVS RTC device.
* tag 'imx-dt-clkdep-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
arm64: dts: imx8mq: add clock for SNVS RTC node
arm64: dts: imx8mm: add clock for SNVS RTC node
arm64: dts: imx8mm: add clock for GPIO node
clk: imx8m: Add GIC clock
dt-bindings: clock: imx8m: Add GIC clock
clk: imx8mm: add SNVS clock to clock tree
dt-bindings: clock: imx8mm: Add SNVS clock
clk: imx8mq: add SNVS clock to clock tree
dt-bindings: clock: imx8mq: Add SNVS clock
clk: imx8mm: add GPIO clocks to clock tree
dt-bindings: clock: imx8mm: Add GPIO clocks
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Tue, 25 Jun 2019 11:51:18 +0000 (04:51 -0700)]
Merge tag 'imx-bindings-5.3' of git://git./linux/kernel/git/shawnguo/linux into arm/dt
i.MX DT bindings for 5.3:
- Add vendor prefix for Purism SPC.
- Add bindings for i.MX8MQ EVK Board, Purism Librem5 devkit and i.MX7
Meerkat96 Board.
- Add LS1028A specific compatible into qDMA bindings doc.
- Move Emtrion i.MX6 board bindings to schema.
- Add missing schemas for i.MX7ULP and i.MX1/31/35 bindings.
* tag 'imx-bindings-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
dt-bindings: arm: fsl: Add missing schemas for i.MX1/31/35
dt-bindings: arm: fsl: Add back missing i.MX7ULP binding
dt-bindings: arm: Move Emtrion i.MX6 board bindings to schema
dt-bindings: arm: fsl: Add the imx8mq boards
dt-bindings: Add an entry for Purism SPC
dt-bindings: fsl-qdma: Add LS1028A qDMA bindings
dt-bindings: arm: Document 96Boards Meerkat96 devicetree binding
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Tue, 25 Jun 2019 11:50:23 +0000 (04:50 -0700)]
Merge tag 'pxa-dt-5.3' of https://github.com/rjarzmik/linux into arm/dt
This is the pxa devicetree changes for 5.3 cycle :
- devicetree pinmux support for bias on pxa3xx
- devicetree pinmux bias usage for raumfeld
* tag 'pxa-dt-5.3' of https://github.com/rjarzmik/linux:
ARM: dts: pxa300-raumfeld-speaker-one: add channel output mapping for STA320
ARM: pxa: raumfeld-common: fix comments in gpio_keys pinctrl node
ARM: pxa: raumfeld-controller: add pinctrl for charger pins
ARM: pxa: raumfeld-controller: fix 'dock detect' GPIO key
ARM: pxa3xx: dts: Add defines for pinctrl-single,bias-pull{up,down}
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Tue, 25 Jun 2019 11:49:42 +0000 (04:49 -0700)]
Merge tag 'at91-5.3-dt' of git://git./linux/kernel/git/at91/linux into arm/dt
AT91 DT for 5.3
- switch to new sckc bindings
- convert soc bindings to json-schema
* tag 'at91-5.3-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/at91/linux:
dt-bindings: arm: Convert Atmel board/soc bindings to json-schema
ARM: dts: at91: sama5d3: switch to new sckc bindings
ARM: dts: at91: at91sam9rl: switch to new sckc bindings
ARM: dts: at91: at91sam9g45: switch to new sckc bindings
ARM: dts: at91: at91sam9x5: switch to new sckc bindings
ARM: dts: at91sam9261ek: remove unused chosen nodes
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Tue, 25 Jun 2019 11:48:32 +0000 (04:48 -0700)]
Merge tag 'tegra-for-5.3-arm64-dt' of git://git./linux/kernel/git/tegra/linux into arm/dt
arm64: tegra: Device tree changes for v5.3-rc1
This contains the bulk of the Tegra changes this cycle. It has a bunch
of improvements across almost all boards. These are mostly small and not
too exciting additions.
Most notably perhaps is the continuation of Jetson Nano support, which
is now mostly on feature parity with Jetson TX1.
* tag 'tegra-for-5.3-arm64-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux: (28 commits)
arm64: tegra: Enable PCIe slots in P2972-0000 board
arm64: tegra: Add P2U and PCIe controller nodes to Tegra194 DT
arm64: tegra: Add PEX DPD states as pinctrl properties
arm64: tegra: Enable ACONNECT, ADMA and AGIC
arm64: tegra: Add ACONNECT, ADMA and AGIC nodes
arm64: tegra: Sort device tree nodes alphabetically
arm64: tegra: Fix Jetson Nano GPU regulator
arm64: tegra: Update Jetson TX1 GPU regulator timings
arm64: tegra: Fix AGIC register range
arm64: tegra: Add INA3221 channel info for Jetson TX2
arm64: tegra: Enable PWM on Jetson Nano
arm64: tegra: Enable CPU sleep on Jetson Nano
arm64: tegra: Add ID EEPROMs on Jetson Nano
arm64: tegra: Add ID EEPROM for Jetson TX2 Developer Kit
arm64: tegra: Add ID EEPROM for Jetson TX2 module
arm64: tegra: Add ID EEPROM for Jetson TX1 Developer Kit
arm64: tegra: Add ID EEPROM for Jetson TX1 module
arm64: tegra: Don't use architected timer for suspend on Tegra210
arm64: tegra: Mark architected timer as always on
arm64: tegra: Add pin control states for I2C on Tegra186
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Tue, 25 Jun 2019 11:47:55 +0000 (04:47 -0700)]
Merge tag 'stm32-dt-for-v5.3-1' of git://git./linux/kernel/git/atorgue/stm32 into arm/dt
STM32 DT updates for v5.3, round 1
Highlights:
----------
MPU part:
-Add stm32mp157a-avenger board support:
This board embeds a STM32MP157a SOC with AC package (TFBGA361, 148 ios)
, 1024MB of DDR3 and STPMIC1A pmic . Several connections are available on this boards:
2x Type A (USB 2.0) Host and 1x Micro B (USB 2.0) OTG, ethernet
10/100/1000, WiFi 5 GHz & 2.4GHz, ...
-Add STMFX support en stm32mp157c-ev1 and enable joystick connected on
it.
-Add I2S and SAI support on stm32mp157c.
-Add and enable support of Vivante GPU on stm32mp157 ED1 and DK1 boards
(EV1 and DK2 inherit of it).
-Add camera support:
-Add DCMI support on stm32mp157c SOC
-Enabled OV5640 camera support on stm32mp157c-ev1 board
-Enable hdmi bridge sii9022 & display controller on stm32mp157c-dk1
board.
MCU part:
-Add STMFX support en stm32746g-eval and enable connections on it:
leds and joystick
* tag 'stm32-dt-for-v5.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32: (27 commits)
ARM: dts: stm32: replace rgmii mode with rgmii-id on stm32mp15 boards
ARM: dts: stm32: Add Avenger96 devicetree support based on STM32MP157A
dt-bindings: arm: stm32: Document Avenger96 devicetree binding
dt-bindings: arm: stm32: Convert STM32 SoC bindings to DT schema
ARM: dts: stm32: Add missing pinctrl definitions for STM32MP157
ARM: dts: stm32: add sai id registers to stm32mp157c
ARM: dts: stm32: add power supply of rm68200 on stm32mp157c-ev1
ARM: dts: stm32: enable display on stm32mp157c-dk1 board
ARM: dts: stm32: Add I2C 1 config for stm32mp157a-dk1
ARM: dts: stm32: enable OV5640 camera on stm32mp157c-ev1 board
ARM: dts: stm32: add DCMI pins to stm32mp157c
ARM: dts: stm32: add DCMI camera interface support on stm32mp157c
ARM: dts: stm32: enable Vivante GPU support on stm32mp157a-dk1 board
ARM: dts: stm32: enable Vivante GPU support on stm32mp157c-ed1 board
ARM: dts: stm32: Add Vivante GPU support on STM32MP157c
ARM: dts: stm32: add i2s pins muxing on stm32mp157
ARM: dts: stm32: add i2s support on stm32mp157c
ARM: dts: stm32: add sai pins muxing on stm32mp157
ARM: dts: stm32: add sai support on stm32mp157c
ARM: dts: stm32: add jedec compatible for nor flash on stm32mp157c-ev1
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Tue, 25 Jun 2019 11:47:08 +0000 (04:47 -0700)]
Merge tag 'mvebu-dt64-5.3-1' of git://git.infradead.org/linux-mvebu into arm/dt
mvebu dt64 for 5.3 (part 1)
For Armada 7K/8K:
- enable AP806 thermal throttling with CPUfreq
- add missing #interrupt-cells property allowing configuring
interrupt for GPIO
On Armada 8040 based board:
- Fix PCI memory window on Mcbin board
- Set SFP power limit on clearfog GT board
- Disable AP I2C on Armada-8040-DB
On Armada 3720 based board espressobin correct the SPI node used for
NOR flash
On Armada 7040 DB board add USB current regulators
* tag 'mvebu-dt64-5.3-1' of git://git.infradead.org/linux-mvebu:
arm64: dts: marvell: add missing #interrupt-cells property
arm64: dts: marvell: armada-7040-db: Add USB current regulators
arm64: dts: armada-3720-espressobin: correct spi node
arm64: dts: marvell: Disable AP I2C on Armada-8040-DB
arm64: dts: marvell: Enable AP806 thermal throttling with CPUfreq
arm64: dts: marvell: Change core numbering in AP806 thermal-node
arm64: dts: marvell: clearfog-gt-8k: set SFP power limit
arm64: dts: marvell: mcbin: enlarge PCI memory window
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Tue, 25 Jun 2019 11:46:25 +0000 (04:46 -0700)]
Merge tag 'mvebu-dt-5.3-1' of git://git.infradead.org/linux-mvebu into arm/dt
mvebu dt for 5.3 (part 1)
Add LCD support on Netgear RN104
* tag 'mvebu-dt-5.3-1' of git://git.infradead.org/linux-mvebu:
ARM: dts: armada: netgear-rn104: Add LCD to RN104 dts.
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Tue, 25 Jun 2019 11:45:45 +0000 (04:45 -0700)]
Merge tag 'renesas-arm64-dt-for-v5.3' of https://git./linux/kernel/git/horms/renesas into arm/dt
Renesas ARM64 Based SoC DT Updates for v5.3
* Renesas SoCs
- Revise usb2_phy nodes and phys properties according to updated bindings
- Use ip=on for bootargs
* R-Car Gen 3 and RZ/G2M (r8a774a1) SoCs
- Add dynamic power coefficient
- Create thermal zone to support IPA
* R-Car E3 (r8a77990) and D3 (r8a77995) SoCs
- Point LVDS0 to its companion LVDS1
* R-Car E3 (r8a77990) SoC
- Corresct register range of DU
* R-Car E3 (r8a77990) based Ebisu board
- Remove renesas, no-ether-link property
* R-Car D3 (r8a77995) based Draak board:
- Remove unnecessary index from vin4 port
* RZ/G2M (r8a774a1) based HiHope main and sub-boards:
- Initial support
- Describe CPU capacity and topoligy
- Enable CMT, HDMI, LEDs, PCIe RWDT, SCIF, SDHI, TMU, and USB 2.0 and 3.0
* RZ/G2E (r8a774c0) SoC based EK874 board:
- Clean up CPU compatible strings
- Enable: Bluetooth, HDMI audio and video, TPU, USB 3.0 and WLAN
* tag 'renesas-arm64-dt-for-v5.3' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (53 commits)
arm64: dts: renesas: hihope-common: Remove "label" from LEDs
arm64: dts: renesas: hihope-common: Add HDMI support
arm64: dts: renesas: r8a774a1: Add HDMI encoder instance
arm64: dts: renesas: r8a774a1: Add dynamic power coefficient
arm64: dts: renesas: r8a774a1: Create thermal zone to support IPA
arm64: dts: renesas: r8a774a1: Add CPU capacity-dmips-mhz
arm64: dts: renesas: r8a774a1: Add CPU topology on r8a774a1 SoC
arm64: dts: renesas: hihope-common: Add LEDs support
arm64: dts: renesas: hihope-common: Enable USB3.0
arm64: dts: renesas: hihope-common: Add USB 2.0 support
arm64: dts: renesas: r8a774a1: Fix USB 2.0 clocks
arm64: dts: renesas: r8a774a1: Add TMU device nodes
arm64: dts: renesas: r8a774a1: Add CMT device nodes
arm64: dts: renesas: hihope-common: Add uSD and eMMC
arm64: dts: renesas: r8a77990: Fix register range of display node
arm64: dts: renesas: cat874: Enable usb role switch support
arm64: dts: renesas: cat874: Enable USB3.0 host/peripheral device node
arm64: dts: renesas: r8a7799[05]: Point LVDS0 to its companion LVDS1
arm64: dts: renesas: hihope-common: Add RWDT support
arm64: dts: renesas: hihope-rzg2-ex: Enable PCIe support
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Tue, 25 Jun 2019 11:44:18 +0000 (04:44 -0700)]
Merge tag 'renesas-arm-dt-for-v5.3' of https://git./linux/kernel/git/horms/renesas into arm/dt
Renesas ARM Based SoC DT Updates for v5.3
* Renesas SoC based boards
- Use ip=on for bootargs
* Renesas R-Car Gen 2 SOC based boards
- Configure PMIC IRQ pinmux
* R-Car V2H (r8a7792) SoC
- Describe CMT devices in DT
* RZ/G1C (r8a77470) based iWave SBC (iwg23s-sbc) and
RZ/G1N (r8a7744) based boards:
- Correct SDHI2 VccQ regulator to fix SDR50 mode
* RZ/A2M (r7s9210) based rza2mevb EVB
RZ/A1H (r7s72100) based rskrza1 board
- Describe input switch in DT
* RZ/A2M (r7s9210) based rza2mevb EVB
- Sort nodes to ease future maintenance
- Add USB host, Ethernet and SDHI support
* RZ/A2M (r7s9210) and RZ/A1H (r7s72100) SoCs
- Describe IRQC device in DT
* tag 'renesas-arm-dt-for-v5.3' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (22 commits)
ARM: dts: r8a7792: Add CMT0 and CMT1 to r8a7792
ARM: dts: iwg23s-sbc: Fix SDHI2 VccQ regulator
ARM: dts: iwg20d-q7-common: Fix SDHI1 VccQ regularor
ARM: dts: rza2mevb: Add input switch
ARM: dts: r7s9210: Add IRQC device node
ARM: dts: rza2mevb: sort nodes of rza2mevb board
ARM: dts: renesas: Use ip=on for bootargs
ARM: dts: rza2mevb: Add USB Host support
ARM: dts: r7s9210: Add USB Device support
ARM: dts: r7s9210: Add USB Host support
ARM: dts: rskrza1: Add input switches
ARM: dts: r7s72100: Add IRQC device node
ARM: dts: r8a779x: Configure PMIC IRQ pinmux
ARM: dts: rza2mevb: Add 48MHz USB clock
ARM: dts: r7s9210: Add USB clock
ARM: dts: rza2mevb: add ethernet aliases
ARM: dts: rza2mevb: Add SDHI support
ARM: dts: rza2mevb: Add Ethernet support
ARM: dts: r7s9210: Add SDHI support
ARM: dts: r7s9210: Add RIIC support
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Tue, 25 Jun 2019 11:43:29 +0000 (04:43 -0700)]
Merge tag 'renesas-dt-bindings-for-v5.3' of https://git./linux/kernel/git/horms/renesas into arm/dt
Renesas ARM Based SoC DT Bindings Updates for v5.3
* Renesas Gen3 DWC HDMI TX Encoder
- Add RZ/G2M (r8a774a1) support
* Renesas R-Car Compare Match Timer (CMT)
- Add R-Car H3 (r8a7795), M3-N (r8a77965) and E3 (r8a77990) support
* Renesas R-Car CAN FD Controller
- Add R-Car M3-N (r8a77965) and E3 (r8a77990), and RZ/G2E (r8a774c0) support
* Renesas R-Car CAN Controller
- Add RZ/G2M (r8a774a1) support
- Correct RZ/G2 clocks
* Vendor prefixes: Add vendor prefix for HopeRun
* Renesas SoCs and boards: Add HopeRun RZ/G2[M] boards
* tag 'renesas-dt-bindings-for-v5.3' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
dt-bindings: display: renesas: Add r8a774a1 support
dt-bindings: timer: renesas, cmt: Document r8a779{5|65|90} CMT support
dt-bindings: can: rcar_canfd: document r8a774c0 support
dt-bindings: can: rcar_canfd: document r8a77990 support
dt-bindings: can: rcar_canfd: document r8a77965 support
dt-bindings: can: rcar_can: Add r8a774c0 support
dt-bindings: can: rcar_can: Fix RZ/G2 CAN clocks
dt-bindings: Add vendor prefix for HopeRun
dt-bindings: arm: renesas: Add HopeRun RZ/G2[M] boards
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Tue, 25 Jun 2019 11:42:05 +0000 (04:42 -0700)]
Merge tag 'sunxi-h3-h5-for-5.3-
201906210812' of https://git./linux/kernel/git/sunxi/linux into arm/dt
This time we only have a single patch for our command branch between
arm and arm64, a fix for the array syntax raised by our DT schemas.
* tag 'sunxi-h3-h5-for-5.3-
201906210812' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
ARM: dts: sunxi: h3/h5: Fix GPIO regulator state array
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Tue, 25 Jun 2019 11:41:39 +0000 (04:41 -0700)]
Merge tag 'sunxi-dt64-for-5.3-
201906210808' of https://git./linux/kernel/git/sunxi/linux into arm/dt
Our usual bunch of arm64 DT changes, this time with:
- Some fixes for the DT schemas that were added during this release
- Wifi support for the H6
- LRADC suppport for the A64
- Some background work on A64 boards, to enable various devices such
as touchscreens, PMIC, audio, wifi, etc.
* tag 'sunxi-dt64-for-5.3-
201906210808' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
arm64: dts: allwinner: h6: Add DMA node
arm64: dts: allwinner: a64: Add lradc node
dt-bindings: input: sun4i-lradc-keys: Add A64 compatible
arm64: dts: allwinner: h6: add r_watchog node
arm64: dts: allwinner: h6: add watchdog node
dt-bindings: watchdog: add Allwinner H6 watchdog
arm64: dts: allwinner: a64: Enable audio on Teres-I
arm64: dts: allwinner: a64: bananapi-m64: Enable PMIC USB power supply
arm64: dts: allwinner: axp803: add USB power supply node
arm64: dts: allwinner: a64: Add pinmux for RGB666 LCD
arm64: dts: allwinner: a64: orangepi-win: Add wifi and bluetooth nodes
arm64: dts: allwinner: h6: add PIO VCC bank supplies for Pine H64
arm64: dts: allwinner: a64-oceanic-5205-5inmfd: Enable GT911 CTP
arm64: dts: allwinner: a64-amarula-relic: Add GT5663 CTP node
arm64: dts: allwinner: a64: move I2C pinctrl to dtsi
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Tue, 25 Jun 2019 11:40:52 +0000 (04:40 -0700)]
Merge tag 'sunxi-dt-for-5.3-
201906210807' of https://git./linux/kernel/git/sunxi/linux into arm/dt
Our usual bunch of patches:
- Some work on the BPi M2-Berry to support various devices
- Convert some bindings to a schema, and a lot of fixes reported by
the schemas we introduced.
- A few other fixes here and there
* tag 'sunxi-dt-for-5.3-
201906210807' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux: (21 commits)
dt-bindings: pwm: Convert Allwinner PWM to a schema
ARM: dts: sun8i: r40: Change the RTC compatible
ARM: dts: sun8i: v3s: Add external crystals accuracy
ARM: dts: sun8i: v3s: Fix the RTC node
ARM: dts: sun6i: Add external crystals accuracy
ARM: dts: sun6i: Fix RTC node
ARM: dts: sun8i: a83t: Add device node for CSI (Camera Sensor Interface)
ARM: dts: gr8-evb: Fix RTC vendor
ARM: dts: sun7i: icnova-swac: Fix the model vendor
ARM: dts: sun8i: a711: Change LRADC node names to avoid warnings
ARM: dts: sun7i: olimex-lime2: Enable ac and power supplies
ARM: dts: sun6i: Add default address and size cells for SPI
ARM: dts: sun8i-h3: Fix wifi in Beelink X2 DT
dt-bindings: bus: Convert Allwinner RSB to a schema
ARM: dts: sun8i: r40: bananapi-m2-ultra: Remove regulator-always-on
ARM: dts: sun8i: v40: bananapi-m2-berry: Add Bluetooth device node
ARM: dts: sun8i: v40: bananapi-m2-berry: Enable AHCI
ARM: dts: sun8i: v40: bananapi-m2-berry: Enable HDMI output
ARM: dts: sun8i: v40: bananapi-m2-berry: Enable GMAC ethernet controller
ARM: dts: sun8i: v40: bananapi-m2-berry: Add GPIO pin-bank regulator supplies
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Tue, 25 Jun 2019 11:38:23 +0000 (04:38 -0700)]
Merge tag 'amlogic-dt' of https://git./linux/kernel/git/khilman/linux-amlogic into arm/dt
ARM: dts: Amlogic updates for v5.3
- SPDX updates
- switch to generic ethernet PHY reset bindings
- add the canvas module
- mxiii-plus board: add regulators
* tag 'amlogic-dt' of https://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
ARM: dts: meson: switch to the generic Ethernet PHY reset bindings
ARM: dts: meson8b: update with SPDX Licence identifier
ARM: dts: meson8b-odroidc1: update with SPDX Licence identifier
ARM: dts: meson8b-mxq: update with SPDX Licence identifier
ARM: dts: meson8: update with SPDX Licence identifier
ARM: dts: meson8-minix-neo-x8: update with SPDX Licence identifier
ARM: dts: meson6: update with SPDX Licence identifier
ARM: dts: meson6-atv1200: update with SPDX Licence identifier
ARM: dts: meson: update with SPDX Licence identifier
ARM: dts: meson8b: mxq: improve support for the TRONFY MXQ S805
ARM: dts: meson8m2: mxiii-plus: add the supply for the Mali GPU
ARM: dts: meson8m2: mxiii-plus: rename the DCDC2 regulator
ARM: dts: meson8b: add the canvas module
ARM: dts: meson8m2: update the offset of the canvas module
ARM: dts: meson8: add the canvas module
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Tue, 25 Jun 2019 11:37:18 +0000 (04:37 -0700)]
Merge tag 'davinci-for-v5.3/dt' of git://git./linux/kernel/git/nsekhar/linux-davinci into arm/dt
This pull request adds CPUFreq support for DA850 boards in device-tree
boot using the generic CPUFREQ_DT driver.
* tag 'davinci-for-v5.3/dt' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
ARM: davinci_all_defconfig: Enable CPUFREQ_DT
ARM: dts: da850-evm: enable cpufreq
ARM: dts: da850-lcdk: enable cpufreq
ARM: dts: da850-lego-ev3: enable cpufreq
ARM: dts: da850: add cpu node and operating points to DT
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Tue, 25 Jun 2019 11:35:02 +0000 (04:35 -0700)]
Merge tag 'aspeed-5.3-devicetree' of git://git./linux/kernel/git/joel/aspeed into arm/dt
ASPEED device tree updates for 5.3
We have various device tree updates from the OpenBMC project to enable
bits and pieces in existing systems, notably updates to Google's Zaius.
There are some AST2500 machines under development:
* Lenovo Hr630
* IBM Swift
* Facebook YAMP
And some AST2400 machines that have been around but out of tree and have
now joined the party:
* YADRO VESNIN
* Microsoft Olympus
* tag 'aspeed-5.3-devicetree' of git://git.kernel.org/pub/scm/linux/kernel/git/joel/aspeed:
ARM: dts: aspeed: Enable video engine on romulus and wtherspoon
ARM: dts: aspeed: Add Inspur fp5280g2 BMC machine
ARM: dts: aspeed: Add YADRO VESNIN BMC
ARM: dts: aspeed: Add Microsoft Olympus BMC
ARM: dts: aspeed: Adding Lenovo Hr630 BMC
ARM: dts: aspeed: Add Facebook YAMP BMC
ARM: dts: aspeed: swift: Add pca9539 devices
ARM: dts: aspeed: Add Swift BMC machine
ARM: dts: aspeed: cmm: enable ehci host controllers
ARM: dts: aspeed: zaius: fixed I2C bus numbers for pcie slots
ARM: dts: aspeed: zaius: update 12V brick I2C address
ARM: dts: aspeed: zaius: add Infineon and Intersil regulators
ARM: dts: aspeed: quanta-q71: Enable p2a node
ARM: dts: aspeed: Add aspeed-p2a-ctrl node
ARM: dts: aspeed: Add Power9 and Power9 CFAM description
ARM: dts: aspeed: Rename flash-controller nodes
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Tue, 25 Jun 2019 11:32:08 +0000 (04:32 -0700)]
Merge tag 'qcom-dts-for-5.3' of git://git./linux/kernel/git/qcom/linux into arm/dt
Qualcomm Device Tree Changes for v5.3
* Add display support to MSM8974
* Add display, backlight, and touchscreen support to MSM8974 Hammerhead
* Update coresight bindings for MSM8974 and APQ8064
* tag 'qcom-dts-for-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux:
ARM: dts: qcom: msm8974-hammerhead: add support for display
ARM: dts: msm8974: add display support
ARM: dts: qcom: msm8974-hammerhead: add support for backlight
ARM: dts: qcom: msm8974-hammerhead: add touchscreen support
ARM: dts: qcom-msm8974: Update coresight DT bindings
ARM: dts: qcom-apq8064: Update coresight DT bindings
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Tue, 25 Jun 2019 11:31:37 +0000 (04:31 -0700)]
Merge tag 'qcom-arm64-for-5.3' of git://git./linux/kernel/git/qcom/linux into arm/dt
Qualcomm ARM64 Updates for v5.3
* Switch to use second gen PON on PM8998
* Add PSCI cupidle states for MSM8996, MSM8998,and SDM845
* Add MSM8996 UFS phy reset controller
* Add propre cpu capacity scaling on MSM8996
* Fixups for APR domain, legacy clocks, and PSCI entry latency on MSM8996
* Enable SMMUs on MSM8996
* Add Dragonboard 845C
* Add Q6V5, GPU, GMU, and AOSS QMP node on SDM845
* Fixup CPU topology on SDM845
* Change USB1 to be peripheral on SDM845 MTP
* Add PCIe Phy, RC nodes, ANOC1 SMMU, and RPMPD node on MSM8998
* Update coresight bindings for MSM8916
* Update idle state names and entry-method on MSM8916
* Add PCIe, RPMPD, LPASS, Q6, TCSR, TuringCC, PSCI cpuidle states,
and CDSP on QCS404
* Add reset-cells property to QCS404 GCC node
* Fixup s3 max voltage, l3 min voltage, drive strength typo, and
s3 supply definition on QCS404-evb
* Fixup ADC outputs and VADC calibration on PMS405
* tag 'qcom-arm64-for-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux: (39 commits)
arm64: dts: qcom: qcs404-evb: fix vdd_apc supply
arm64: dts: qcom: pm8998: Use qcom,pm8998-pon binding for second gen pon
arm64: dts: qcom: msm8996: Enable SMMUs
arm64: dts: qcom: msm8996: Correct apr-domain property
arm64: dts: qcom: Add Dragonboard 845c
arm64: dts: qcom: qcs404-evb: Enable PCIe
arm64: dts: qcom: qcs404: Add PCIe related nodes
arm64: dts: qcom: msm8998: Add PCIe PHY and RC nodes
arm64: dts: qcom: msm8998: Add ANOC1 SMMU node
arm64: dts: qcom: msm8996: Stop using legacy clock names
arm64: dts: msm8996: fix PSCI entry-latency-us
arm64: dts: qcom: msm8998: Add PSCI cpuidle low power states
arm64: dts: qcom: sdm845: Add Q6V5 MSS node
arm64: dts: qcom: Add AOSS QMP node
arm64: dts: qcom-qcs404: Add reset-cells to GCC node
arm64: dts: qcom-msm8916: Update coresight DT bindings
arm64: dts: qcom: msm8998: Add rpmpd node
arm64: dts: qcom: qcs404: Add rpmpd node
arm64: dts: qcom: qcs404: Move lpass and q6 into soc
arm64: dts: qcom: qcs404: Fully describe the CDSP
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Tue, 25 Jun 2019 11:30:50 +0000 (04:30 -0700)]
Merge tag 'hisi-arm32-dt-for-5.3' of git://github.com/hisilicon/linux-hisi into arm/dt
ARM: DT: Hisilicon ARM32 SoCs updates for v5.3
- Updated CoreSight funnel and replicator using new bindings to fix warning
for the hip04.
* tag 'hisi-arm32-dt-for-5.3' of git://github.com/hisilicon/linux-hisi:
ARM: dts: hip04: Update coresight DT bindings
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Tue, 25 Jun 2019 11:30:13 +0000 (04:30 -0700)]
Merge tag 'hisi-arm64-dt-for-5.3' of git://github.com/hisilicon/linux-hisi into arm/dt
ARM64: DT: Hisilicon SoCs DT updates for v5.3
* Hi3660 SoC and related boards:
- Added CoreSight trace components
* Hi6220 SoC and related boards:
- Updated CoreSight funnel and replicator using new bindings to fix warning
* tag 'hisi-arm64-dt-for-5.3' of git://github.com/hisilicon/linux-hisi:
arm64: dts: hi3660: Add CoreSight support
arm64: dts: hi6220: Update coresight DT bindings
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Tue, 25 Jun 2019 11:15:53 +0000 (04:15 -0700)]
Merge tag 'arm-soc/for-5.3/devicetree-v2' of https://github.com/Broadcom/stblinux into arm/dt
This pull request contain Broadcom ARM-based SoCs Device Tree changes
for 5.3 please pull the following:
- Lukas enables DMA support for the BCM2835 (Raspberry Pi) SPI
controller
- Florian fixes a number of dtc W=1 warnings in the Broadcom DTS files
and provides a fix for devices failing to boot after the removal of
skelton.dtsi (that commit has been submitted as a separate fix)
* tag 'arm-soc/for-5.3/devicetree-v2' of https://github.com/Broadcom/stblinux:
ARM: dts: BCM5301X: Fix most DTC W=1 warnings
ARM: dts: NSP: Fix the bulk of W=1 DTC warnings
ARM: dts: BCM63xx: Fix DTC W=1 warnings
ARM: dts: BCM53573: Fix DTC W=1 warnings
ARM: dts: bcm-mobile: Fix most DTC W=1 warnings
ARM: dts: Cygnus: Fix most DTC W=1 warnings
ARM: dts: Fix BCM7445 DTC warnings
ARM: bcm283x: Enable DMA support for SPI controller
ARM: dts: bcm: Add missing device_type = "memory" property
Signed-off-by: Olof Johansson <olof@lixom.net>
Peter Chen [Mon, 24 Jun 2019 02:02:57 +0000 (10:02 +0800)]
ARM: dts: imx7ulp-evk: enable USBOTG1 support
Enable USBOTG1 support for evk board, it is dual-role function
port.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Peter Chen [Mon, 24 Jun 2019 02:02:56 +0000 (10:02 +0800)]
ARM: dts: imx7ulp: add imx7ulp USBOTG1 support
Add imx7ulp USBOTG1 support.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Michael Grzeschik [Mon, 17 Jun 2019 16:14:32 +0000 (18:14 +0200)]
ARM: dts: imx6qdl-kontron-samx6i: add Kontron SMARC SoM Support
The patch adds the following interfaces according the SMARC Spec 1.1
[1] and provided schematics:
- SMARC SPI0/1
Note: Since Kontron still uses silicon revisions below 1.3 they have
add a spi-nor to implement Workaround #1 of erratum ERR006282.
- SMARC SDIO
- SMARC LCD
- SMARC HDMI
- SMARC Management pins
Note: Kontron don't route all of these pins to the i.MX6, some are
routed to the SoM CPLD.
- SMARC GPIO
- SMARC CSI Camera
Note: As specified in [1] the data lanes are shared to cover the
csi and the parallel case. The case depends on the baseboard so
muxing the data lanes is not part of this patch.
- SMARC I2S
- SMARC Watchdog
Note: The watchdog output pin is routed to the CPLD and the SMARC
header. The CPLD performs a reset after a 30s timeout so we
need to enable the watchdog per default.
- SMARC module eeprom
Due to the lack of hardware not all of these interfaces are tesetd.
[1] https://sget.org/standards/smarc
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Daniel Mack [Thu, 9 May 2019 16:04:39 +0000 (18:04 +0200)]
ARM: dts: pxa300-raumfeld-speaker-one: add channel output mapping for STA320
These settings are needed to make the hardware operable.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Daniel Mack [Wed, 24 Apr 2019 18:58:58 +0000 (20:58 +0200)]
ARM: pxa: raumfeld-common: fix comments in gpio_keys pinctrl node
Careless oversight.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Daniel Mack [Wed, 24 Apr 2019 18:58:57 +0000 (20:58 +0200)]
ARM: pxa: raumfeld-controller: add pinctrl for charger pins
The PEN2 line needs to be pulled up for the charger to enter high-current
mode. Do this with a static pull on the GPIO.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Daniel Mack [Wed, 24 Apr 2019 18:58:56 +0000 (20:58 +0200)]
ARM: pxa: raumfeld-controller: fix 'dock detect' GPIO key
The dock detection input key is active low. Also add a pinmux for it.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Daniel Mack [Wed, 24 Apr 2019 18:58:55 +0000 (20:58 +0200)]
ARM: pxa3xx: dts: Add defines for pinctrl-single,bias-pull{up,down}
This allows users of the pinctrl driver to specify either
pinctrl-single,bias-pullup = MPF_PULL_UP;
or
pinctrl-single,bias-pulldown = MPF_PULL_DOWN;
To activate the pull bits in the MFP registers.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Angus Ainslie (Purism) [Thu, 20 Jun 2019 17:05:32 +0000 (11:05 -0600)]
arm64: dts: librem5: enable the SNVS power key
Enable the snvs power key.
Signed-off-by: Angus Ainslie (Purism) <angus@akkea.ca>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Angus Ainslie (Purism) [Thu, 20 Jun 2019 17:04:39 +0000 (11:04 -0600)]
arm64: dts: librem5: Limit the USB to 5V
The charge controller can handle 14V but the PTC on the devkit can only
handle 6V so limit the negotiated voltage to 5V.
Signed-off-by: Angus Ainslie (Purism) <angus@akkea.ca>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Frank Li [Mon, 24 Jun 2019 01:58:48 +0000 (09:58 +0800)]
arm64: dts: imx8qxp: added ddr performance monitor nodes
Add ddr performance monitor
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Shawn Guo [Mon, 24 Jun 2019 01:03:00 +0000 (09:03 +0800)]
arm64: dts: imx8qxp: sort LSIO subsystem devices
We prefer to sort device nodes under simple bus in order of unit
address. Let's sort the devices under lsio_subsys properly.
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Shawn Guo [Mon, 24 Jun 2019 01:00:49 +0000 (09:00 +0800)]
arm64: dts: imx8qxp: sort alias alphabetically
We prefer to sort alias entries alphabetically, so let's move serial0
to the right place.
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Daniel Baluta [Tue, 18 Jun 2019 21:05:16 +0000 (00:05 +0300)]
arm64: dts: imx8qxp: Add lsio_mu13 node
lsio_mu13 node is used to communicate with DSP.
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Priit Laes [Mon, 17 Jun 2019 16:14:31 +0000 (18:14 +0200)]
ARM: dts: imx6qdl-kontron-samx6i: Add iMX6-based Kontron SMARC-sAMX6i module
SMARC-sAMX6i is a SMARC (Smart Mobility Architecture) compliant
module.
Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Daniel Baluta [Tue, 4 Jun 2019 12:32:57 +0000 (20:32 +0800)]
arm64: dts: imx8mm-evk: Enable audio codec wm8524
i.MX8MM has one wm8524 audio codec connected with
SAI3 digital audio interface.
This patch uses simple-card machine driver in order
to enable wm8524 codec.
We need to set:
* SAI3 pinctrl configuration
* codec reset gpio pinctrl configuration
* clock hierarchy
* codec node
* simple-card configuration
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Florian Fainelli [Tue, 28 May 2019 23:01:33 +0000 (16:01 -0700)]
ARM: dts: BCM5301X: Fix most DTC W=1 warnings
Fix the bulk of the unit_address_vs_reg warnings and unnecessary
\#address-cells/#size-cells without "ranges" or child "reg" property
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Florian Fainelli [Tue, 28 May 2019 23:01:34 +0000 (16:01 -0700)]
ARM: dts: NSP: Fix the bulk of W=1 DTC warnings
Fix the bulk of the unit_address_vs_reg warnings and unnecessary
\#address-cells/#size-cells without "ranges" or child "reg" property
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Florian Fainelli [Tue, 28 May 2019 23:01:32 +0000 (16:01 -0700)]
ARM: dts: BCM63xx: Fix DTC W=1 warnings
Fix the bulk of the unit_address_vs_reg warnings and unnecessary
\#address-cells/#size-cells without "ranges" or child "reg" property
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Florian Fainelli [Tue, 28 May 2019 23:01:31 +0000 (16:01 -0700)]
ARM: dts: BCM53573: Fix DTC W=1 warnings
Fix the the unit_address_vs_reg warnings and unnecessary
\#address-cells/#size-cells without "ranges" or child "reg" property
warnings.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Florian Fainelli [Tue, 28 May 2019 23:01:30 +0000 (16:01 -0700)]
ARM: dts: bcm-mobile: Fix most DTC W=1 warnings
Fix the bulk of the unit_address_vs_reg warnings and unnecessary
\#address-cells/#size-cells without "ranges" or child "reg" property
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Florian Fainelli [Tue, 28 May 2019 23:01:29 +0000 (16:01 -0700)]
ARM: dts: Cygnus: Fix most DTC W=1 warnings
Fix the bulk of the unit_address_vs_reg warnings and unnecessary
\#address-cells/#size-cells without "ranges" or child "reg" property
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Florian Fainelli [Tue, 28 May 2019 23:01:28 +0000 (16:01 -0700)]
ARM: dts: Fix BCM7445 DTC warnings
Fixes a number of unit_address_vs_reg warnings:
DTC arch/arm/boot/dts/bcm7445-bcm97445svmb.dtb
arch/arm/boot/dts/bcm7445.dtsi:66.6-225.4: Warning (unit_address_vs_reg): /rdb: node has a reg or ranges property, but no unit name
arch/arm/boot/dts/bcm7445.dtsi:227.21-298.4: Warning (unit_address_vs_reg): /memory_controllers: node has a reg or ranges property, but no unit name
arch/arm/boot/dts/bcm7445-bcm97445svmb.dts:9.9-14.4: Warning (unit_address_vs_reg): /memory: node has a reg or ranges property, but no unit name
arch/arm/boot/dts/bcm7445.dtsi:255.10-275.5: Warning (simple_bus_reg): /memory_controllers/memc@1: simple-bus unit address format error, expected "80000"
arch/arm/boot/dts/bcm7445.dtsi:277.10-297.5: Warning (simple_bus_reg): /memory_controllers/memc@2: simple-bus unit address format error, expected "100000"
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Florian Fainelli [Mon, 3 Jun 2019 18:59:51 +0000 (11:59 -0700)]
Merge tag 'tags/bcm2835-dt-next-2019-06-01' into devicetree/next
This pull requests enables DMA support for the main SPI controller
on all Raspberry Pis.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Lukas Wunner [Thu, 9 May 2019 17:03:00 +0000 (19:03 +0200)]
ARM: bcm283x: Enable DMA support for SPI controller
Without this, the driver for the BCM2835 SPI controller uses interrupt
mode instead of DMA mode, incurring a significant performance penalty.
The Foundation's device tree has had these attributes for years, but for
some reason they were never upstreamed.
They were originally contributed by Noralf Trønnes and Martin Sperl:
https://github.com/raspberrypi/linux/commit/
25f3e064afc8
https://github.com/raspberrypi/linux/commit/
e0edb52b47e6
The DREQ numbers 6 and 7 are documented in section 4.2.1.3 of:
https://www.raspberrypi.org/app/uploads/2012/02/BCM2835-ARM-Peripherals.pdf
Tested-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Reviewed-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Cc: Martin Sperl <kernel@martin.sperl.org>
Cc: Noralf Trønnes <noralf@tronnes.org>
Michael Mei [Mon, 27 May 2019 09:04:47 +0000 (17:04 +0800)]
arm64: dts: mt8183: add efuse and Mediatek Chip id node to read
support for reading chip ID and efuse
Signed-off-by: Michael Mei <michael.mei@mediatek.com>
Signed-off-by: Erin Lo <erin.lo@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Erin Lo [Mon, 27 May 2019 09:04:46 +0000 (17:04 +0800)]
arm64: dts: mt8183: add spi node
Add spi DTS node to the mt8183 and mt8183-evb.
Signed-off-by: Mengqi Zhang <Mengqi.Zhang@mediatek.com>
Signed-off-by: Erin Lo <erin.lo@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Zhiyong Tao [Mon, 27 May 2019 09:04:45 +0000 (17:04 +0800)]
arm64: dts: mt8183: Add auxadc device node
Add auxadc device node for MT8183
Signed-off-by: Zhiyong Tao <zhiyong.tao@mediatek.com>
Signed-off-by: Erin Lo <erin.lo@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Zhiyong Tao [Mon, 27 May 2019 09:04:44 +0000 (17:04 +0800)]
arm64: dts: mt8183: add pinctrl device node
The commit adds pinctrl device node for mt8183
Signed-off-by: Zhiyong Tao <zhiyong.tao@mediatek.com>
Signed-off-by: Erin Lo <erin.lo@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Hsin-Yi, Wang [Mon, 27 May 2019 09:04:43 +0000 (17:04 +0800)]
arm64: dts: mt8183: add capacity-dmips-mhz
Pinned the frequency to the max and run dhrystone to get the value.
little cpu: 11071 (max freq: 1989000)
big cpu: 15293 (max freq: 1989000)
11071 : 15293 ~= 741 : 1024
Signed-off-by: Erin Lo <erin.lo@mediatek.com>
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Christophe Roullier [Mon, 17 Jun 2019 08:50:18 +0000 (10:50 +0200)]
ARM: dts: stm32: replace rgmii mode with rgmii-id on stm32mp15 boards
On disco and eval board, Tx and Rx delay are applied (pull-up of 4.7k
put on VDD) so which correspond to RGMII-ID mode with internal RX and TX
delays provided by the PHY, the MAC should not add the RX or TX delays
in this case
Signed-off-by: Christophe Roullier <christophe.roullier@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Manivannan Sadhasivam [Wed, 12 Jun 2019 07:54:51 +0000 (13:24 +0530)]
ARM: dts: stm32: Add Avenger96 devicetree support based on STM32MP157A
Add devicetree support for Avenger96 board based on STM32MP157A MPU
from ST Micro. This board is one of the 96Boards Consumer Edition board
from Arrow Electronics and has the following features:
SoC: STM32MP157AAC
PMIC: STPMIC1A
RAM: 1024 Mbyte @ 533MHz
Storage: eMMC v4.51: 8 Gbyte
microSD Socket: UHS-1 v3.01
Ethernet Port: 10/100/1000 Mbit/s, IEEE 802.3 Compliant
Wireless: WiFi 5 GHz & 2.4GHz IEEE 802.11a/b/g/n/ac
Bluetooth®v4.2 (BR/EDR/BLE)
USB: 2x Type A (USB 2.0) Host and 1x Micro B (USB 2.0) OTG
Display: HDMI: WXGA (1366x768)@ 60 fps, HDMI 1.4
LED: 4x User LED, 1x WiFi LED, 1x BT LED
More information about this board can be found in 96Boards website:
https://www.96boards.org/product/avenger96/
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Manivannan Sadhasivam [Wed, 12 Jun 2019 07:54:50 +0000 (13:24 +0530)]
dt-bindings: arm: stm32: Document Avenger96 devicetree binding
This commit documents Avenger96 devicetree binding based on
STM32MP157 SoC.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Manivannan Sadhasivam [Wed, 12 Jun 2019 07:54:49 +0000 (13:24 +0530)]
dt-bindings: arm: stm32: Convert STM32 SoC bindings to DT schema
This commit converts STM32 SoC bindings to DT schema using jsonschema.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Manivannan Sadhasivam [Wed, 12 Jun 2019 07:54:48 +0000 (13:24 +0530)]
ARM: dts: stm32: Add missing pinctrl definitions for STM32MP157
Add missing pinctrl definitions for STM32MP157 MPU.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Olivier Moysan [Tue, 11 Jun 2019 11:45:56 +0000 (13:45 +0200)]
ARM: dts: stm32: add sai id registers to stm32mp157c
Add identification registers to address range
of SAI DT parent node, for stm32mp157c.
Signed-off-by: Olivier Moysan <olivier.moysan@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Yannick Fertré [Tue, 21 May 2019 15:03:18 +0000 (17:03 +0200)]
ARM: dts: stm32: add power supply of rm68200 on stm32mp157c-ev1
This patch adds a new property (power-supply) to panel rm68200 (raydium)
on stm32mp157c-ev1.
Signed-off-by: Yannick Fertré <yannick.fertre@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Vidya Sagar [Wed, 12 Jun 2019 09:53:36 +0000 (15:23 +0530)]
arm64: tegra: Enable PCIe slots in P2972-0000 board
Enable PCIe controller nodes to enable respective PCIe slots on
P2972-0000 board. Following is the ownership of slots by different
PCIe controllers.
Controller-0 : M.2 Key-M slot
Controller-1 : On-board Marvell eSATA controller
Controller-3 : M.2 Key-E slot
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Vidya Sagar [Wed, 12 Jun 2019 09:53:35 +0000 (15:23 +0530)]
arm64: tegra: Add P2U and PCIe controller nodes to Tegra194 DT
Add P2U (PIPE to UPHY) and PCIe controller nodes to device tree.
The Tegra194 SoC contains six PCIe controllers and twenty P2U instances
grouped into two different PHY bricks namely High-Speed IO (HSIO-12 P2Us)
and NVIDIA High Speed (NVHS-8 P2Us) respectively.
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Manikanta Maddireddy [Tue, 18 Jun 2019 18:02:02 +0000 (23:32 +0530)]
arm64: tegra: Add PEX DPD states as pinctrl properties
Add PEX deep power down states as pinctrl properties to set in PCIe driver.
In Tegra210, BIAS pads are not in power down mode when clamps are applied.
To set the pads in DPD, pass the PEX DPD states as pinctrl properties to
PCIe driver.
Signed-off-by: Manikanta Maddireddy <mmaddireddy@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Sameer Pujar [Wed, 19 Jun 2019 11:51:22 +0000 (17:21 +0530)]
arm64: tegra: Enable ACONNECT, ADMA and AGIC
Enable ACONNECT, ADMA and AGIC devices on Jetson TX2 and Jetson AGX
Xavier.
Verified driver probe path and devices get registered fine.
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Sameer Pujar [Wed, 19 Jun 2019 11:51:21 +0000 (17:21 +0530)]
arm64: tegra: Add ACONNECT, ADMA and AGIC nodes
Add device tree nodes for the ACONNECT, ADMA and AGIC devices on
Tegra186 and Tegra194.
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Ben Ho [Mon, 27 May 2019 09:04:42 +0000 (17:04 +0800)]
arm64: dts: Add Mediatek SoC MT8183 and evaluation board dts and Makefile
Add basic chip support for Mediatek 8183, include
uart node with correct uart clocks, pwrap device
Add clock controller nodes, include topckgen, infracfg,
apmixedsys and subsystem.
Signed-off-by: Ben Ho <Ben.Ho@mediatek.com>
Signed-off-by: Erin Lo <erin.lo@mediatek.com>
Signed-off-by: Seiya Wang <seiya.wang@mediatek.com>
Signed-off-by: Weiyi Lu <weiyi.lu@mediatek.com>
Signed-off-by: Hsin-Hsiung Wang <hsin-hsiung.wang@mediatek.com>
Signed-off-by: Eddie Huang <eddie.huang@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Maxime Ripard [Thu, 16 May 2019 12:08:48 +0000 (14:08 +0200)]
dt-bindings: pwm: Convert Allwinner PWM to a schema
The Allwinner SoCs have a PWM controller supported in Linux, with a
matching Device Tree binding.
Now that we have the DT validation in place, let's convert the device tree
bindings for that controller over to a YAML schemas.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Magnus Damm [Mon, 17 Jun 2019 09:17:08 +0000 (18:17 +0900)]
ARM: dts: r8a7792: Add CMT0 and CMT1 to r8a7792
Add CMT0 and CMT1 to the R-Car Gen2 V2H (r8a7792) SoC.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Fabrizio Castro [Mon, 3 Jun 2019 09:53:52 +0000 (10:53 +0100)]
ARM: dts: iwg23s-sbc: Fix SDHI2 VccQ regulator
SDR50 isn't working anymore because the GPIO regulator
driver is using descriptors since
commit
d6cd33ad7102 ("regulator: gpio: Convert to use descriptors")
which in turn causes the system to use the polarity of the
GPIOs (as specified in the DT) for selecting the states,
but the polarity specified in the DT is wrong.
This patch fixes the regulator DT definition, and that fixes
SDR50.
Fixes:
9eb36b945b5c ("ARM: dts: iwg23s-sbc: Add uSD and eMMC support")
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Fabrizio Castro [Mon, 3 Jun 2019 09:53:51 +0000 (10:53 +0100)]
ARM: dts: iwg20d-q7-common: Fix SDHI1 VccQ regularor
SDR50 isn't working anymore because the GPIO regulator
driver is using descriptors since
commit
d6cd33ad7102 ("regulator: gpio: Convert to use descriptors")
which in turn causes the system to use the polarity of the
GPIOs (as specified in the DT) for selecting the states,
but the polarity specified in the DT is wrong.
This patch fixes the regulator DT definition, and that fixes
SDR50.
Fixes:
029efb3a03c5 ("ARM: dts: iwg20d-q7: Add SDHI1 support")
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Chris Brandt [Tue, 4 Jun 2019 20:09:14 +0000 (15:09 -0500)]
ARM: dts: rza2mevb: Add input switch
Add support for input switch SW3 on the Renesas RZ/A2M EVB
development board.
Note that this uses the IRQ interrupt, as the RZ/A2 GPIO controller
does not include interrupt support
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Chris Brandt [Tue, 4 Jun 2019 20:09:13 +0000 (15:09 -0500)]
ARM: dts: r7s9210: Add IRQC device node
Enable support for the IRQC on RZ/A2M, which is a small front-end to the
GIC. This allows to use up to 8 external interrupts with configurable
sense select.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Yoshihiro Kaneko [Fri, 17 May 2019 14:43:07 +0000 (23:43 +0900)]
ARM: dts: rza2mevb: sort nodes of rza2mevb board
This patch sorts the nodes of arch/arm/boot/dts/r7s9210-rza2mevb.dts.
* Sort subnodes of root ("/") node alphabetically
* Sort following top-level nodes alphabetically
* Sort subnodes of pinctrl alphabetically
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
[simon: rebase and sort new ehci nodes]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Magnus Damm [Sat, 18 May 2019 10:03:57 +0000 (19:03 +0900)]
ARM: dts: renesas: Use ip=on for bootargs
Convert bootargs from ip=dhcp to ip=on
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Martin Blumenstingl [Sat, 15 Jun 2019 10:38:30 +0000 (12:38 +0200)]
ARM: dts: meson: switch to the generic Ethernet PHY reset bindings
The snps,reset-gpio bindings are deprecated in favour of the generic
"Ethernet PHY reset" bindings.
Replace snps,reset-gpio from the ðmac node with reset-gpios in the
ethernet-phy node. The old snps,reset-active-low property is now encoded
directly as GPIO flag inside the reset-gpios property.
snps,reset-delays-us is converted to reset-assert-us and
reset-deassert-us. reset-assert-us is the second cell from
snps,reset-delays-us while reset-deassert-us was the third cell.
Instead of blindly copying the old values (which seems strange since
they gave the PHY one second to come out of reset) over this also
updates the delays based on the datasheets:
- RTL8211F PHY on the Odroid-C1 and MXIII-Plus needs a 10ms assert
delay (the datasheet mentions: "For a complete PHY reset, this pin
must be asserted low for at least 10ms") and a 30ms deassert delay
(the datasheet mentions: "Wait for a further 30ms (for internal
circuits settling time) before accessing the PHY register"). The
old settings used 10ms for assert and 1000ms for deassert.
- IP101GR PHY on the EC-100 and MXQ needs a 10ms assert delay (the
datasheet mentions: "Trst | Reset period | 10ms") and a 10ms deassert
delay as well (the datasheet mentions: "Tclk_MII_rdy | MII/RMII clock
output ready after reset released | 10ms")). The old settings used
10ms for assert and 1000ms for deassert.
No functional changes intended.
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Thierry Reding [Thu, 20 Jun 2019 09:32:24 +0000 (11:32 +0200)]
arm64: tegra: Sort device tree nodes alphabetically
Device tree nodes without unit-address are to be sorted alphabetically.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Jon Hunter [Thu, 20 Jun 2019 08:17:02 +0000 (09:17 +0100)]
arm64: tegra: Fix Jetson Nano GPU regulator
There are a few issues with the GPU regulator defined for Jetson Nano
which are:
1. The GPU regulator is a PWM based regulator and not a fixed voltage
regulator.
2. The output voltages for the GPU regulator are not correct.
3. The regulator enable ramp delay is too short for the regulator and
needs to be increased. 2ms should be sufficient.
4. This is the same regulator used on Jetson TX1 and so make the ramp
delay and settling time the same as Jetson TX1.
Cc: stable@vger.kernel.org
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Fixes:
6772cd0eacc8 ("arm64: tegra: Add NVIDIA Jetson Nano Developer Kit support")
Signed-off-by: Thierry Reding <treding@nvidia.com>
Jon Hunter [Thu, 20 Jun 2019 08:17:01 +0000 (09:17 +0100)]
arm64: tegra: Update Jetson TX1 GPU regulator timings
The GPU regulator enable ramp delay for Jetson TX1 is set to 1ms which
not sufficient because the enable ramp delay has been measured to be
greater than 1ms. Furthermore, the downstream kernels released by NVIDIA
for Jetson TX1 are using a enable ramp delay 2ms and a settling delay of
160us. Update the GPU regulator enable ramp delay for Jetson TX1 to be
2ms and add a settling delay of 160us.
Cc: stable@vger.kernel.org
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Fixes:
5e6b9a89afce ("arm64: tegra: Add VDD_GPU regulator to Jetson TX1")
Signed-off-by: Thierry Reding <treding@nvidia.com>
Jon Hunter [Thu, 20 Jun 2019 08:17:00 +0000 (09:17 +0100)]
arm64: tegra: Fix AGIC register range
The Tegra AGIC interrupt controller is an ARM GIC400 interrupt
controller. Per the ARM GIC device-tree binding, the first address
region is for the GIC distributor registers and the second address
region is for the GIC CPU interface registers. The address space for
the distributor registers is 4kB, but currently this is incorrectly
defined as 8kB for the Tegra AGIC and overlaps with the CPU interface
registers. Correct the address space for the distributor to be 4kB.
Cc: stable@vger.kernel.org
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Fixes:
bcdbde433542 ("arm64: tegra: Add AGIC node for Tegra210")
Signed-off-by: Thierry Reding <treding@nvidia.com>
Nicolin Chen [Mon, 17 Jun 2019 22:16:59 +0000 (15:16 -0700)]
arm64: tegra: Add INA3221 channel info for Jetson TX2
There are four INA3221 chips on the Jetson TX2 (p3310 + p2771).
And each INA3221 chip has three input channels to monitor power.
So this patch adds these 12 channels to the DT of Jetson TX2, by
following the DT binding of INA3221 and official documents from
https://developer.nvidia.com/embedded/downloads
tegra186-p3310:
https://developer.nvidia.com/embedded/dlc/jetson-tx2-series-modules-oem-product-design-guide
tegra186-p2771-0000:
http://developer.nvidia.com/embedded/dlc/jetson-tx1-tx2-developer-kit-carrier-board-spec-
20180618
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Thierry Reding [Fri, 7 Jun 2019 14:01:11 +0000 (16:01 +0200)]
arm64: tegra: Enable PWM on Jetson Nano
Signed-off-by: Thierry Reding <treding@nvidia.com>
Rob Herring [Fri, 17 May 2019 15:39:11 +0000 (10:39 -0500)]
dt-bindings: arm: Convert Atmel board/soc bindings to json-schema
Convert Atmel SoC bindings to DT schema format using json-schema.
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: devicetree@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Eddie James [Tue, 2 Apr 2019 02:42:29 +0000 (02:42 +0000)]
ARM: dts: aspeed: Enable video engine on romulus and wtherspoon
Enable the video engine and add it's optional reserved memory region.
Use 32MB for the reserved memory since the video engine could need up to
two 1920x1200@32bpp source buffers.
Source buffers: 2 * 1920 * 1200 * 4 =
18432000 bytes
In addition, the V4L2 subsystem will allocate any number of compression
buffers, each at most 1/8th the size of the source buffer.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
John Wang [Thu, 13 Jun 2019 07:00:02 +0000 (15:00 +0800)]
ARM: dts: aspeed: Add Inspur fp5280g2 BMC machine
The fp5280g2 is an OpenPower server platform with an ASPEED AST2500 BMC.
Signed-off-by: John Wang <wangzqbj@inspur.com>
Reviewed-by: Lei YU <mine260309@gmail.com>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Jorge Ramirez-Ortiz [Wed, 19 Jun 2019 18:16:53 +0000 (20:16 +0200)]
arm64: dts: qcom: qcs404-evb: fix vdd_apc supply
The invalid definition in the supply causes the Qualcomm's EVB-1000
and EVB-4000 not to boot.
Fix the boot issue by correctly defining the supply: vdd_s3 (namely
"vdd_apc") is actually connected to vph_pwr.
Reported-by: Niklas Cassel <niklas.cassel@linaro.org>
Tested-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <agross@kernel.org>
Martin Blumenstingl [Sat, 15 Jun 2019 10:43:51 +0000 (12:43 +0200)]
arm64: dts: meson: g12a: x96-max: add the Ethernet PHY interrupt line
X96 Max has the PHY reset and interrupt lines are identical to the
Odroid-N2:
- GPIOZ_14 is the interrupt on X96 Max
- GPIOZ_15 is the reset line on X96 Max
Add GPIOZ_14 as PHY interrupt line on the X96 Max so we don't have to
poll for the PHY status.
Suggested-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Martin Blumenstingl [Sat, 15 Jun 2019 10:43:50 +0000 (12:43 +0200)]
arm64: dts: meson: g12b: odroid-n2: add the Ethernet PHY interrupt line
The interrupt line of the RTL8211F PHY is routed to the GPIOZ_14 pad.
Describe this in the device tree so the PHY framework doesn't have to
poll the PHY status.
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Martin Blumenstingl [Sat, 15 Jun 2019 10:38:32 +0000 (12:38 +0200)]
arm64: dts: meson: g12b: odroid-n2: add the Ethernet PHY reset line
The reset line of the RTL8211F PHY is routed to the GPIOZ_15 pad.
Describe this in the device tree so the PHY framework can bring the PHY
into a known state when initializing it. GPIOZ_15 doesn't support
driving the output HIGH (to take the PHY out of reset, only output LOW
to reset the PHY is supported). The datasheet states it's an "3.3V input
tolerant open drain (OD) output pin". Instead there's a pull-up resistor
on the board to take the PHY out of reset. The GPIO itself will be set
to INPUT mode to take the PHY out of reset and LOW to reset the PHY,
which is achieved with the flags (GPIO_ACTIVE_LOW | GPIO_OPEN_DRAIN).
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Martin Blumenstingl [Sat, 15 Jun 2019 10:38:31 +0000 (12:38 +0200)]
arm64: dts: meson: use the generic Ethernet PHY reset GPIO bindings
The snps,reset-gpio bindings are deprecated in favour of the generic
"Ethernet PHY reset" bindings.
Replace snps,reset-gpio from the ðmac node with reset-gpios in the
ethernet-phy node. The old snps,reset-active-low property is now encoded
directly as GPIO flag inside the reset-gpios property.
snps,reset-delays-us is converted to reset-assert-us and
reset-deassert-us. reset-assert-us is the second cell from
snps,reset-delays-us while reset-deassert-us was the third cell.
Instead of blindly copying the old values (which seems strange since
they gave the PHY one second to come out of reset) over this also
updates the delays based on the datasheets:
- the Realtek RTL8211F PHY needs a 10ms assert delay (the datasheet
mentions: "For a complete PHY reset, this pin must be asserted low
for at least 10ms") and a 30ms deassert delay (the datasheet
mentions: "Wait for a further 30ms (for internal circuits settling
time) before accessing the PHY register". This applies to the
following boards: GXBB NanoPi K2, GXBB Odroid-C2, GXBB Vega S95
variants, GXBB Wetek variants, GXL P230, GXM Khadas VIM2, GXM Nexbox
A1, GXM Q200, GXM RBox Pro boards.
- the ICPlus IP101GR PHY needs a 10ms assert delay (the datasheet
mentions: "Trst | Reset period | 10ms") and a deassert delay of 10ms
as well (the datasheet mentions: "Tclk_MII_rdy | MII/RMII clock
output ready after reset released | 10ms"). This applies to the GXBB
Nexbox A95X board.
- the Micrel KSZ9031 seems to require a 100us delay but use the same
(seemingly safe) values from RTL8211F due to lack of a board to verify
this. This applies to the GXBB P200 board.
The GXBB P201 board is left out from this conversion because it doesn't
have a dedicated PHY node (because it's not clear which PHY is used on
that board).
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Martin Blumenstingl [Sat, 15 Jun 2019 10:38:29 +0000 (12:38 +0200)]
arm64: dts: meson: g12a: x96-max: fix the Ethernet PHY reset line
The Odroid-N2 schematics show that the following pins are used for the
reset and interrupt lines:
- GPIOZ_14 is the PHY interrupt line
- GPIOZ_15 is the PHY reset line
The GPIOZ_14 and GPIOZ_15 pins are special. The datasheet describes that
they are "3.3V input tolerant open drain (OD) output pins". This means
the GPIO controller can drive the output LOW to reset the PHY. To
release the reset it can only switch the pin to input mode. The output
cannot be driven HIGH for these pins.
This requires configuring the reset line as GPIO_OPEN_DRAIN because
otherwise the PHY will be stuck in "reset" state (because driving the
pin HIGH seems to result in the same signal as driving it LOW).
The reset line works together with a pull-up resistor (R143 in the
Odroid-N2 schematics). The SoC can drive GPIOZ_14 LOW to assert the PHY
reset. However, since the SoC can't drive the pin HIGH (to release the
reset) we switch the mode to INPUT and let the pull-up resistor take
care of driving the reset line HIGH.
Switch to GPIOZ_15 for the PHY reset line instead of using GPIOZ_14
(which actually is the interrupt line).
Move from the "snps" specific resets to the MDIO framework's
reset-gpios because only the latter honors the GPIO flags.
Use the GPIO flags (GPIO_ACTIVE_LOW | GPIO_OPEN_DRAIN) to match with
the pull-up resistor because this will:
- drive the output LOW to reset the PHY (= active low)
- switch the pin to INPUT mode so the pull-up will take the PHY out of
reset
Fixes:
51d116557b2044 ("arm64: dts: meson-g12a-x96-max: Add Gigabit Ethernet Support")
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Jerome Brunet [Mon, 10 Jun 2019 12:49:31 +0000 (14:49 +0200)]
arm64: dts: meson: g12a: sort sdio nodes correctly
Fix sdio node order in the soc device tree
Fixes:
a1737347250e ("arm64: dts: meson: g12a: add SDIO controller")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Olof Johansson [Wed, 19 Jun 2019 16:03:38 +0000 (09:03 -0700)]
Merge tag 'ti-k3-soc-for-v5.3' of git://git./linux/kernel/git/kristo/linux into arm/dt
Texas Instruments K3 SoC family changes for 5.3
- Add support for the new J721e SoC, includes basic peripherals needed for
booting up the device
- New peripheral support added for AM654x:
* TI SCI irqchip
* GPIO
* MCU SRAM
* R5Fs
* MSMC RAM
* SERDES and PCIe
* tag 'ti-k3-soc-for-v5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/kristo/linux: (26 commits)
arm64: dts: ti: k3-j721e: Add the MCU SRAM node
arm64: dts: ti: k3-j721e: Add interrupt controllers in wakeup domain
arm64: dts: ti: k3-j721e: Add interrupt controllers in main domain
arm64: dts: ti: k3-j721e-main: Add Main NavSS Interrupt controller node
arm64: defconfig: Enable TI's J721E SoC platform
arm64: dts: ti: Add support for J721E Common Processor Board
soc: ti: Add Support for J721E SoC config option
arm64: dts: ti: Add Support for J721E SoC
dt-bindings: serial: 8250_omap: Add compatible for J721E UART controller
dt-bindings: arm: ti: Add bindings for J721E SoC
arm64: dts: ti: am654-base-board: Disable SERDES and PCIe
arm64: dts: k3-am6: Add PCIe Endpoint DT node
arm64: dts: k3-am6: Add PCIe Root Complex DT node
arm64: dts: k3-am6: Add SERDES DT node
arm64: dts: k3-am6: Add mux-controller DT node required for muxing SERDES
arm64: dts: k3-am6: Add "socionext,synquacer-pre-its" property to gic_its
arm64: dts: ti: k3-am65: Add MSMC RAM ranges in interconnect node
arm64: dts: ti: k3-am65: Add R5F ranges in interconnect nodes
arm64: dts: ti: k3-am65-mcu: Add the MCU RAM node
arm64: dts: ti: k3-am65: Add MCU SRAM ranges in interconnect nodes
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Wed, 19 Jun 2019 16:00:58 +0000 (09:00 -0700)]
Merge tag 'socfpga_dts_updates_for_v5.3' of git://git./linux/kernel/git/dinguyen/linux into arm/dt
SoCFPGA DTS updates for v5.3
- Use the new "altr,socfpga-stmmac-a10-s10" for the EMAC controllers on
Arria10/Stratix10
- Add the ltc2497 i2c entry on the Arria10 devkit
- Add the EMAC OCP reset property on the Arria10
* tag 'socfpga_dts_updates_for_v5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux:
ARM: dts: arria10: Add EMAC OCP reset property
ARM: dts: socfpga: add ltc2497 on arria10 devkit
arm64: dts: stratix10: use the "altr,socfpga-stmmac-a10-s10" binding
ARM: dts: socfpga: use the "altr,socfpga-stmmac-a10-s10" binding
Signed-off-by: Olof Johansson <olof@lixom.net>
Thierry Reding [Fri, 14 Jun 2019 15:41:04 +0000 (17:41 +0200)]
arm64: tegra: Enable CPU sleep on Jetson Nano
Jetson Nano implements CPU sleep via PSCI, much like any of the other
Tegra X1 platforms. Enable the sleep states to allow the CPU to go into
lower power states when idle.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Thierry Reding [Thu, 6 Jun 2019 15:54:05 +0000 (17:54 +0200)]
arm64: tegra: Add ID EEPROMs on Jetson Nano
The Jetson Nano has two ID EEPROMs, one for the module and another for
the carrier board. Add both to the device tree so that they can be read
from at runtime.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Thierry Reding [Thu, 13 Jun 2019 16:53:29 +0000 (18:53 +0200)]
arm64: tegra: Add ID EEPROM for Jetson TX2 Developer Kit
There is an ID EEPROM on the Jetson TX2 carrier board, part of the
Jetson TX2 Developer Kit, that exposes information that can be used to
identify the carrier board. Add the device tree node so that operating
systems can access this EEPROM.
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Thierry Reding [Thu, 13 Jun 2019 16:53:28 +0000 (18:53 +0200)]
arm64: tegra: Add ID EEPROM for Jetson TX2 module
There is an ID EEPROM in the Jetson TX2 module that stores various bits
of information to indentify the module. Add the device tree node so that
operating systems can access this EEPROM.
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
projects / platform / kernel / linux-rpi.git / log