Christian Gmeiner [Mon, 10 Nov 2014 13:35:48 +0000 (14:35 +0100)]
ot1200: add support for EHCI
U-Boot 2014.10-17457-g0b23780-dirty (Nov 10 2014 - 11:41:04)
CPU: Freescale i.MX6D rev1.2 at 792 MHz
Reset cause: WDOG
Board: ot1200
I2C: ready
DRAM: 1 GiB
MMC: FSL_SDHC: 0, FSL_SDHC: 1
SF: Detected M25P16 with page size 256 Bytes, erase size 64 KiB, total 2 MiB
In: serial
Out: serial
Err: serial
Net: using phy at 0
FEC [PRIME]
Hit any key to stop autoboot: 0
=> usb start
(Re)start USB...
USB0: Port not available.
USB1: USB EHCI 1.00
scanning bus 1 for devices... 4 USB Device(s) found
=> usb tree
USB device tree:
1 Hub (480 Mb/s, 0mA)
| u-boot EHCI Host Controller
|
+-2 Hub (480 Mb/s, 2mA)
|
+-3 Mass Storage (480 Mb/s, 80mA)
| USBest Technology USB Mass Storage Device
0000000000028B
|
+-4 Vendor specific (480 Mb/s, 2mA)
=>
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Fabio Estevam [Mon, 10 Nov 2014 12:34:26 +0000 (10:34 -0200)]
mx28evk: README: Revision C is also supported
Adjust the text to mention that rev C of the board is also supported.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Nikita Kiryanov [Wed, 29 Oct 2014 17:28:33 +0000 (19:28 +0200)]
arm: imx: make bmode command work with SPL/U-Boot combo
The bmode command forces the SoC to use a specific boot device
by writing its boot mode into SRC_GPR9, and notifying the SoC of
the change using SRC_GPR10[28] bit: if the bit is on, bootROM
uses the value in SRC_GPR9 instead of SRC_SMBR1 to determine
the boot device.
SPL on the other hand is oblivious to this distinction, so once
the bootROM loads SPL from the device configured in SRC_GPR10,
SPL will attempt to load U-Boot from the device configured in
SRC_SMBR1, which is not updated by the bootROM to the value in
SRC_GPR9.
The result is that the selected boot device is not used across all
the boot stages.
Update spl_boot_device() to look at gpr9 when necessary.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Troy Kisky <troy.kisky@boundarydevices.com>
Cc: Tim Harvey <tharvey@gateworks.com>
Cc: Eric Nelson <eric.nelson@boundarydevices.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Heiko Schocher <hs@denx.de>
Tom Rini [Tue, 11 Nov 2014 20:49:10 +0000 (15:49 -0500)]
Merge branch 'master' of git://git.denx.de/u-boot-uniphier
Michal Simek [Tue, 11 Nov 2014 14:45:36 +0000 (15:45 +0100)]
Revert "lib: bootm: add missing include"
This is a MIME GnuPG-signed message. If you see this text, it means that
your E-mail or Usenet software does not support MIME signed messages.
The Internet standard for MIME PGP messages, RFC 2015, was published in 1996.
To open this message correctly you will need to install E-mail or Usenet
software that supports modern Internet standards.
This reverts commit
1e96220a5687efae2aed45ce56e143336c40d0a7.
Remove duplicated vxworks.h header.
The same change was done by
"ARM: prevent compiler warnings from bootm.c"
(sha1:
8d196e52b58d1e50a80c2f5067b201cda521c75c)
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Masahiro Yamada [Tue, 11 Nov 2014 13:18:22 +0000 (22:18 +0900)]
ARM: UniPhier: call pin_init() also in the normal boot
CONFIG_UNIPHIER_SERIAL has been moved to Kconfig and
it is defined in ./.config but not in spl/.config,
so pin_init() should be called from the normal image
so that UART works correctly.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Masahiro Yamada [Tue, 11 Nov 2014 13:18:21 +0000 (22:18 +0900)]
ARM: UniPhier: consolidate board_postclk_init() function
This commit merges
arch/arm/cpu/armv7/uniphier/ph1-*/board_postclk_init.c
to
arch/arm/cpu/armv7/uniphier/board_postclk_init.c
Because PH1-Pro4 does not have the BCU block, add __weak to
bcu_init().
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Masahiro Yamada [Tue, 11 Nov 2014 12:50:41 +0000 (21:50 +0900)]
ARM: UniPhier: decrease pre-reloc malloc area size
In the current implementation of the boot sequence of UniPhier
platform, 32KB temporary RAM is available before relocation.
The malloc area and the stack shares the 32KB area.
With CONFIG_SYS_MALLOC_F_LEN set to 0x7000 (28KB), only 0x1000 (4KB)
is left for the stack. In some use cases, the system hangs up
with stack over-flow.
Even with driver-model UART enabled, the malloc area of 0x2000 (8KB)
should be enough.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Masahiro Yamada [Fri, 7 Nov 2014 12:08:52 +0000 (21:08 +0900)]
ARM: UniPhier: add set_pinsel macro for use in assembly code
The function sg_set_pinsel is useful for switching I/O pins
but it can be only used in C code. This commit adds a simple
macro that is available in asm code.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Masahiro Yamada [Fri, 7 Nov 2014 09:48:34 +0000 (18:48 +0900)]
ARM: UniPhier: enable USB features
FAT-formated USB storage device access is available.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Masahiro Yamada [Fri, 7 Nov 2014 09:48:33 +0000 (18:48 +0900)]
usb: UniPhier: add UniPhier on-chip EHCI host driver support
Support EHCI host driver used on Panasonic UniPhier platform.
Since Device Tree is not supported on UniPhier yet, the base address
of USB cores are passed from board files (platdevice.c).
TODO for me:
Move the base address to device trees.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Marek Vasut <marex@denx.de>
Masahiro Yamada [Fri, 7 Nov 2014 09:48:32 +0000 (18:48 +0900)]
ARM: UniPhier: add MIO register file
This commit adds register defines of MIO (Media I/O) block
of UniPhier platform. This file is necessary to control
the reset signals of the USB cores.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Masahiro Yamada [Fri, 7 Nov 2014 09:48:31 +0000 (18:48 +0900)]
usb: add basic USB configs in Kconfig
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Marek Vasut <marex@denx.de>
Masahiro Yamada [Fri, 7 Nov 2014 09:33:52 +0000 (18:33 +0900)]
ARM: UniPhier: add EHCI host pin settings for PH1-Pro4
These IO pins are necessary for port power control and
over current detect.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Masahiro Yamada [Thu, 6 Nov 2014 11:16:42 +0000 (20:16 +0900)]
ARM: UniPhier: move DDR related configuration to Kconfig
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Masahiro Yamada [Wed, 5 Nov 2014 05:25:15 +0000 (14:25 +0900)]
ARM: UniPhier: reset on-board devices on start-up
If a support card is attached to the main board, the on-board
SMSC9118 LAN controller is available. It must be kept in reset
state for a while on start-up.
When the board is kicked via a debbuger rather than pushing the
hardware reset button, on-board chips are not reset; in this case
the reset signals should be asserted by software.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Masahiro Yamada [Thu, 30 Oct 2014 03:11:14 +0000 (12:11 +0900)]
serial: UniPhier: borrow macros from linux/serial_reg.h
The same bit-field macros are defined in include/linux/serial_reg.h
so let's include it and delete duplicated defines.
Also, remove unnecessary inclusion of <common.h>.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Tom Rini [Mon, 10 Nov 2014 21:19:51 +0000 (16:19 -0500)]
Prepare v2015.01-rc1
Signed-off-by: Tom Rini <trini@ti.com>
Tom Rini [Mon, 10 Nov 2014 14:20:52 +0000 (09:20 -0500)]
Merge branch 'master' of git://git.denx.de/u-boot-i2c
Tom Rini [Mon, 10 Nov 2014 14:20:38 +0000 (09:20 -0500)]
Merge branch 'master' of git://git.denx.de/u-boot-blackfin
Tom Rini [Sat, 8 Nov 2014 01:35:20 +0000 (20:35 -0500)]
Merge branch 'master' of git://git.denx.de/u-boot-arm
Dominik Muth [Thu, 28 Aug 2014 10:25:27 +0000 (12:25 +0200)]
Added support for comments in input to mkenvimage.
This patch adds support for comments in the input to mkenvimage, i.e. in
the environment source: All lines starting with a # in the firs column
will be ignored.
Additionally empty lines will also be ignored.
Signed-off-by: Dominik Muth <dominik.muth@bkvibro.com>
Jorgen Lundman [Fri, 7 Nov 2014 01:08:35 +0000 (10:08 +0900)]
ZFS: Clean up cppcheck warnings where relevant, leaked memory etc
In a message from Wolfgang Denk highlighting warnings from cppcheck,
the patch will address those that are correctly diagnosed. Some are
false-positives:
> [fs/zfs/zfs.c:937]: (error) Memory leak: l
dmu_read() allocates "l" if successful, so error-case should not free
it.
> [fs/zfs/zfs.c:1141]: (error) Memory leak: dnbuf
dmu_read() allocates "dnbuf" if successful, so error-case should not
free it.
> [fs/zfs/zfs.c:1372]: (error) Memory leak: osp
zio_read() allocates "osp" if successful, so error-case should
not free it.
> [fs/zfs/zfs.c:1726]: (error) Memory leak: nvlist
int_zfs_fetch_nvlist() allocates "nvlist" if successful, so error-case
should not free it.
Signed-off-by: Jorgen Lundman <lundman@lundman.net>
Wolfgang Denk [Thu, 6 Nov 2014 13:03:05 +0000 (14:03 +0100)]
board/esd/common/auto_update.c: fix Uninitialized variable
cppcheck reports:
[board/esd/common/auto_update.c:458]: (error) Uninitialized variable: cnt
The variable is not really used anywhere, so remove it.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Acked-by: Matthias Fuchs <matthias.fuchs@esd.eu>
Wolfgang Denk [Thu, 6 Nov 2014 13:03:04 +0000 (14:03 +0100)]
ARM: MXS: fix Uninitialized variable error
cppcheck reports:
[arch/arm/cpu/arm926ejs/mxs/timer.c:96]: (error) Uninitialized
variable: now
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Nobuhiro Iwamatsu [Tue, 4 Nov 2014 04:28:50 +0000 (13:28 +0900)]
i2c: rcar_i2c: Fix order of restart and clear status
In case of repeated START condition, the restart has to be kicked
before clear status (MSR register). If it is kicked after clear status,
R-Car I2C may transfer data (TXD register) or receive data (RXD register)
instead of transferring slave address (MAR register).
Signed-off-by: Ryo Kataoka <ryo.kataoka.wt@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Shaveta Leekha [Mon, 3 Nov 2014 05:13:14 +0000 (10:43 +0530)]
drivers/i2c/fsl_i2c: Change CONFIG_I2C_TIMEOUT to 100ms
Some slow I2C devices like Power Monitor(ZM7304) at times
do not work well with low timeout value, so I2C bus get stuck
during read cycle with this device, changing it to 100ms from
10ms works fine
A lot of other i2c drivers like mxc and i2c drivers of BOOTROM
also use relax timeouts to give sufficient ticks to work well
with slower devices
Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Dirk Eibach [Wed, 29 Oct 2014 14:56:44 +0000 (15:56 +0100)]
ppc4xx: Handle i2c stuck on combined xfer
ppc4xx i2c master gets stuck on errors while repeated start is
active. Can be easily reproduced by "i2c md" on an unpopulated
i2c address. There is not stop condition given, scl remains
pulled low.
The only way out seems to be doing a stop manually and then a
soft reset.
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
Dirk Eibach [Wed, 29 Oct 2014 14:56:43 +0000 (15:56 +0100)]
ppc4xx: Fix i2c repeated start
Debugging some i2c trouble I saw on my scope that repeated
start is not working properply. The 4xx even held clock pulled down
after transfers. Having a look in the driver I realized
that IIC_CNTL_RPST is set on that part of the transfer that should
begin with a repeated start. But repeated start is about not sending a
stop condition, so IIC_CNTL_RPST has to be set on the last transfer
before the repeated start happens.
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
Sonic Zhang [Fri, 15 Aug 2014 09:08:50 +0000 (17:08 +0800)]
bfin: the max bfin sdh block count is 127
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Sonic Zhang [Tue, 12 Aug 2014 10:45:26 +0000 (18:45 +0800)]
bfin: make the CPU macro of LDR target more genenric
Remove BFIN from the CPU macro in Makefile.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Wolfgang Denk [Thu, 6 Nov 2014 13:03:02 +0000 (14:03 +0100)]
board/matrix_vision/mvblx/sys_eeprom.c: fix buffer overflow
Fix error detected by cppcheck:
[board/matrix_vision/mvblx/sys_eeprom.c:353]: (error) Buffer is
accessed out of bounds.
Signed-off-by: Wolfgang Denk <wd@denx.de>
cc: Michael Jones <michael.jones@matrix-vision.de>
Acked-by: Michael Jones <michael.jones@matrix-vision.de>
Wolfgang Denk [Thu, 6 Nov 2014 13:03:01 +0000 (14:03 +0100)]
common/cmd_fitupd.c: restore corrupted file
This file got corrupted by the automatic editin of commit 1a45966 "Add
GPL-2.0+ SPDX-License-Identifier to source files"; restore the
opiginal content and manually insert the SPDX ID.
The bug was detected by running cppcheck, which reported:
[common/cmd_fitupd.c:8]: (error) Invalid number of character ({) when
these macros are defined: 'CONFIG_UPDATE_TFTP'.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Wolfgang Denk [Thu, 6 Nov 2014 13:03:00 +0000 (14:03 +0100)]
drivers/net/uli526x.c: fix syntax error
Fix error detected by cppcheck:
[drivers/net/uli526x.c:551]: (error) printf format string requires 3
parameters but only 2 are given.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Roy Zang <tie-fei.zang@freescale.com>
Wolfgang Denk [Thu, 6 Nov 2014 13:02:58 +0000 (14:02 +0100)]
board/cogent/lcd.c: fix syntax error
Fix error detected by cppcheck:
[board/cogent/lcd.c:237]: (error) Invalid number of character (()
when these macros are defined:
'CONFIG_SHOW_ACTIVITY;CONFIG_STATUS_LED'.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Wolfgang Denk [Thu, 6 Nov 2014 13:02:57 +0000 (14:02 +0100)]
cppcheck cleanup: fix nullPointer errors
There are a number of places where U-Boot intentionally and legally
accesses physical address 0x0000, for example when installing
exception vectors on systems where these are located in low memory.
Add "cppcheck-suppress nullPointer" comments to silence cppcheck
where this is intentional and legal.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Timo Ketola [Thu, 6 Nov 2014 12:39:05 +0000 (14:39 +0200)]
doc: fix documentation of out-of-tree build
Correct environment variable for output directory is KBUILD_OUTPUT.
Signed-off-by: Timo Ketola <timo@exertus.fi>
Dominic Sacré [Tue, 4 Nov 2014 23:30:18 +0000 (00:30 +0100)]
tools/env: Fix environment size and CRC on 64-bit hosts
On architectures where 'long' is 64 bit, the u-boot environment
as seen by the fw_env tools was missing 4 bytes.
This patch fixes getenvsize(), and thus also ensures that the
environment's CRC32 checksum is calculated correctly.
Signed-off-by: Dominic Sacré <dominic.sacre@gmx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Tom Rini <trini@ti.com>
Stefan Roese [Fri, 31 Oct 2014 12:57:42 +0000 (13:57 +0100)]
MAINTAINERS: CFI flash maintainership only includes the CFI related files
All the other files in drivers/mtd/* are not really CFI related. So lets
only include the files that are CFI specific.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Jagan Teki <jagannadh.teki@gmail.com>
Acked-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Acked-by: Heiko Schocher <hs@denx.de>
Masahiro Yamada [Thu, 30 Oct 2014 02:06:13 +0000 (11:06 +0900)]
kbuild: sync misc scripts with Linux 3.18-rc1
This commit imports some updates in misc scripts from Linux 3.18-rc1.
[1] commit
cbb4d3e6510b99522719c5ef0 by Horia Geanta
scripts/kernel-doc: handle object-like macros
[2] commit
164f0d2efaaef83 by Michal Marek
kbuild: Fix handling of backslashes in *.cmd files
[3] commit
270a00963cd367214e by Randy Dunlap
scripts/kernel-doc: recognize __meminit
[4] commit
a4954fd7724c0f55361eb5 by Masahiro Yamada
kbuild: remove obj-n and lib-n handling
[5] commit
5b2389b45d1a9c12b9f by Masahiro Yamada
kbuild: simplify build, clean, modbuiltin shorthands
Signed-off-by: Horia Geanta <horia.geanta@freescale.com>
Signed-off-by: Michal Marek <mmarek@suse.cz>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Masahiro Yamada [Thu, 30 Oct 2014 02:06:12 +0000 (11:06 +0900)]
kconfig: sync kconfig files with Linux 3.18-rc1
This commit imports Kconfig updates from Linux 3.18-rc1.
'kvmconfig' and 'tinyconfig' help message have been commented out
since they are unavailable at least now; in the future perhaps
we can implement 'tinyconfig' to disable most of CONFIG_CMD_* to
create a very small U-Boot image.
[1] commit
3aaefce10351 by Josh Triplett
x86, platform, kconfig: move kvmconfig functionality to a helper
[2] commit
0da1d4a0b951 by Josh Triplett
x86: Add "make tinyconfig" to configure the tiniest possible kernel
[3] commit
c40724d3f381 by Brian Norris
kconfig: lxdialog: fix spelling
[4] commit
7285996aa000 by Brian Norris
kconfig: nconfig: fix multi-byte UTF handling
Signed-off-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Masahiro Yamada [Thu, 30 Oct 2014 02:06:11 +0000 (11:06 +0900)]
kbuild: sync top Makefile with Linux 3.18-rc1
Since Linux 3.15, relative path feature and related fixes,
cleanups have been merged to the top Makefile.
The relative path feature looks stable enough, so let's import it
to U-Boot along with various cleanups.
Commits imported from Linux (some need adjustment) are:
[1] commit
7e1c04779efd by Michal Marek
kbuild: Use relative path for $(objtree)
[2] commit
890676c65d69 by Michal Marek
kbuild: Use relative path when building in the source tree
[3] commit
9da0763bdd82 by Michal Marek
kbuild: Use relative path when building in a subdir of the source tree
[4] commit
c2e28dc975ea by Michal Marek
kbuild: Print the name of the build directory
[5] commit
066b7ed95580 by Michal Marek
kbuild: Do not print the build directory with make -s
[6] commit
3f1d9a6cec01 by Michal Marek
kbuild: make -s should be used with kernelrelease/kernelversion/image_name
[7] commit
7ff525712acf by Masahiro Yamada
kbuild: fake the "Entering directory ..." message more simply
[8] commit
745a254322c8 by Masahiro Yamada
kbuild: use $(Q) for sub-make target
[9] commit
aa55c8e2f7a3 by Masahiro Yamada
kbuild: handle C=... and M=... after entering into build directory
[10] commit
ab7474ea5361 by Borislav Petkov
Kbuild: Ignore GREP_OPTIONS env variable
To use relative path feature, tools/Makefile and scripts/Makefile.autoconf
must be tweaked.
Signed-off-by: Michal Marek <mmarek@suse.cz>
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Masahiro Yamada [Thu, 30 Oct 2014 02:06:10 +0000 (11:06 +0900)]
kbuild: improve multi-objs dependency and cleanups
Since Linux 3.18-rc1, Kbuild is able to handle multi-objs
dependency correctly, which also allows us futher cleanups
of some makefiles.
This commit imports those commits:
[1] commit
c8589d1e9e01 by Masahiro Yamada
kbuild: handle multi-objs dependency appropriately
[2] commit
97e3226e6e98 by Masahiro Yamada
kbuild: handle the dependency of multi-objs hostprogs appropriately
[3] commit
022af62d0190 by Masahiro Yamada
kbuild: refactor script/kconfig/Makefile
[4] commit
221ecca6cafe by Masahiro Yamada
kbuild: remove redundant clean-files from scripts/kconfig/Makefile
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Masahiro Yamada [Thu, 30 Oct 2014 02:06:09 +0000 (11:06 +0900)]
kbuild: bug fixes and cleanups of Makefile.host
This commit imports updates of scripts/Makefile.host
from Linux 3.18-rc1.
Imported commits are:
[1] commit
d8d9efe22709 by Masahiro Yamada
kbuild: fix a typo in scripts/Makefile.host
[2] commit
edb950c17de0 by Masahiro Yamada
kbuild: fix a bug of C++ host program handling
[3] commit
62e2210798ed by Masahiro Yamada
kbuild: drop shared library support from Makefile.host
[4] commit
663935593915 by Masahiro Yamada
kbuild: clean up scripts/Makefile.host
[5] commit
1791ff7179f6 by Masahiro Yamada
kbuild: clean-up and bug fix of scripts/Makefile.host
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Masahiro Yamada [Thu, 30 Oct 2014 01:58:32 +0000 (10:58 +0900)]
kbuild: remove "clobber" target
Now we stick to Linux Kernel's build system, so squash
"clobber" to "clean" target.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Rabin Vincent [Wed, 29 Oct 2014 22:21:41 +0000 (23:21 +0100)]
hush: make run_command() return an error on parsing failure
run_command() returns success even if the command had a syntax error;
correct this behaviour.
Signed-off-by: Rabin Vincent <rabin@rab.in>
Acked-by: Simon Glass <sjg@chromium.org)
Rabin Vincent [Wed, 29 Oct 2014 22:21:40 +0000 (23:21 +0100)]
hush: fix segfault on syntax error
Hush segfaults if it sees a syntax error while attempting to parse a
command:
$ ./u-boot -c "'"
...
syntax error
Segmentation fault (core dumped)
This is due to a NULL pointer dereference of in_str->p in static_peek().
The problem is that the exit condition for the loop in
parse_stream_outer() checks for rcode not being -1, but rcode is only
ever 0 or 1.
Signed-off-by: Rabin Vincent <rabin@rab.in>
Acked-by: Simon Glass <sjg@chromium.org)
Tested-by: Simon Glass <sjg@chromium.org)
Rabin Vincent [Wed, 29 Oct 2014 22:21:39 +0000 (23:21 +0100)]
hush: return consistent codes from run_command()
Attempting to run:
- an empty string
- a string with just spaces
returns different error codes, 1 for the empty string and 0
for the string with just spaces. Make both of them return
0 for consistency.
Signed-off-by: Rabin Vincent <rabin@rab.in>
Acked-by: Simon Glass <sjg@chromium.org)
Rabin Vincent [Wed, 29 Oct 2014 22:21:38 +0000 (23:21 +0100)]
sandbox: init cli for -c
sandbox crashes if a variable is set in the -c command, because
hush's top_vars is not allocated. Call cli_init() from sandbox
to ensure this is done before we execute the -c command.
$ ./u-boot -c 'a=1'
...
Segmentation fault (core dumped)
Signed-off-by: Rabin Vincent <rabin@rab.in>
Acked-by: Simon Glass <sjg@chromium.org)
Tested-by: Simon Glass <sjg@chromium.org)
Rabin Vincent [Wed, 29 Oct 2014 22:21:37 +0000 (23:21 +0100)]
dlmalloc: ensure gd is set for early alloc
Attempting to run the sandbox leads to a segfault, because some dynamic
libraries (outside of u-boot) attempt to use malloc() to allocate memory
before u-boot's gd variable is initialized.
Check for gd not being NULL in the SYS_MALLOC_F_LEN handling, so that
malloc() doesn't crash when called at this point.
$ gdb -q --args ./u-boot
(gdb) r
Program received signal SIGSEGV, Segmentation fault.
0x0000000000412b9b in malloc (bytes=bytes@entry=37) at common/dlmalloc.c:2184
2184 if (!(gd->flags & GD_FLG_RELOC)) {
(gdb) p gd
$1 = (gd_t *) 0x0
(gdb) bt
#0 0x0000000000412b9b in malloc (bytes=bytes@entry=37) at common/dlmalloc.c:2184
#1 0x00007ffff75bf8e1 in set_binding_values (domainname=0x7ffff11f4f12 "libgpg-error", dirnamep=0x7fffffffe168, codesetp=0x0)
at bindtextdom.c:228
#2 0x00007ffff75bfb4c in set_binding_values (codesetp=0x0, dirnamep=0x7fffffffe168, domainname=<optimized out>) at bindtextdom.c:350
#3 __bindtextdomain (domainname=<optimized out>, dirname=0x7ffff11f4f00 "/usr/share/locale") at bindtextdom.c:348
#4 0x00007ffff11eca17 in ?? () from /lib/x86_64-linux-gnu/libgpg-error.so.0
#5 0x00007ffff7dea9fa in call_init (l=<optimized out>, argc=argc@entry=1, argv=argv@entry=0x7fffffffe208,
env=env@entry=0x7fffffffe218) at dl-init.c:78
#6 0x00007ffff7deaae3 in call_init (env=0x7fffffffe218, argv=0x7fffffffe208, argc=1, l=<optimized out>) at dl-init.c:36
#7 _dl_init (main_map=0x7ffff7ffe1a8, argc=1, argv=0x7fffffffe208, env=0x7fffffffe218) at dl-init.c:126
#8 0x00007ffff7ddd1ca in _dl_start_user () from /lib64/ld-linux-x86-64.so.2
Signed-off-by: Rabin Vincent <rabin@rab.in>
Acked-by: Simon Glass <sjg@chromium.org>
Tom Rini [Sat, 25 Oct 2014 11:38:31 +0000 (07:38 -0400)]
power_spi.c: Rewrite pmic_reg function
The pmic_spi_free function isn't ever used, and as the frameworks stand
today, cannot be, so remove it. Integrate the probe function into
pmic_reg as it's not really a "probe" today. Finally, add an err label
for the common failure cases.
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@ti.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Noam Camus [Wed, 22 Oct 2014 14:17:49 +0000 (17:17 +0300)]
image-fdt: boot_get_fdt() return value when no DTB exists
I believe that when no DTB is around we should return 1.
This why I fixed such scenarious to not return zero anymore.
Else kernel might get NULL pointer to DTB which doesn't exists.
Signed-off-by: Noam Camus <noamc@ezchip.com>
Anatolij Gustschin [Tue, 21 Oct 2014 20:31:26 +0000 (22:31 +0200)]
powerpc: o2dnt: convert to generic board
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Marek Vasut [Sat, 11 Oct 2014 16:42:58 +0000 (18:42 +0200)]
net: smc911x: Keep MAC programmed
Make sure to keep the MAC address programmed in the SMC911x ADDRH
and ADDRL registers. Linux can read those registers to determine
the MAC address on EEPROM-less configurations.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Tom Rini <trini@ti.com>
Pavel Machek [Tue, 9 Sep 2014 13:16:10 +0000 (15:16 +0200)]
sort drivers/mmc/Makefile
Sort drivers/mmc makefile, as requested by wd.
Signed-off-by: Pavel Machek <pavel@denx.de>
Acked-by: Chin Liang See <clsee@altera.com>
Masahiro Yamada [Thu, 6 Nov 2014 18:32:07 +0000 (03:32 +0900)]
generic-board: make compile-time noise for non-generic boards
Commit
0f605c1501f6 (Start the deprecation process for generic board)
added a run-time warning message. Let's be noisier for non-generic
boards to inform the dead line of the conversion.
This commit intentionally outputs a warning message to stdout.
We still have many unconverted boards. If we print the message
to stderr, MAKEALL and buildman will report tons of broken boards
and really important information will be buried.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@ti.com>
Tom Rini [Fri, 7 Nov 2014 21:18:35 +0000 (16:18 -0500)]
Merge git://git.denx.de/u-boot-ti
Igor Grinberg [Mon, 3 Nov 2014 09:32:27 +0000 (11:32 +0200)]
omap3: cm-t3517: add LCD/DVI and splash support
Add support for splash screen on both DVI and SCF0403 LCD.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Reviewed-by: Tom Rini <trini@ti.com>
Igor Grinberg [Mon, 3 Nov 2014 09:32:26 +0000 (11:32 +0200)]
omap3: cm-t3517: add Ethernet support
Add both EMAC and SMC911x support.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Reviewed-by: Tom Rini <trini@ti.com>
Igor Grinberg [Mon, 3 Nov 2014 09:32:25 +0000 (11:32 +0200)]
omap3: cm-t3517: add USB support
Add both host and mUSB support.
Currently, the selection between host USB and mUSB is done through the
config file.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Reviewed-by: Tom Rini <trini@ti.com>
Igor Grinberg [Wed, 5 Nov 2014 12:25:35 +0000 (14:25 +0200)]
omap3: cm-t3517: add basic board support
CompuLab cm-t3517 is Computer on Module (CoM) based on AM3517 SoC.
Features: up to 256MB DDR2, up to 512MB NAND, USB hub, mUSB, WiFi, BT,
Analog audio codec, touch screen controller, LED.
Add basic support including:
LED, Serial console, NAND, MMC, GPIO, I2C, 256MB DRAM.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Igor Grinberg [Mon, 3 Nov 2014 09:32:23 +0000 (11:32 +0200)]
omap: hsmmc: assume cd gpio is active low
Switch the default CD GPIO polarity to active low.
The current hsmmc driver assumption that the CD GPIO is active high, but
in the real hardware, usually the opposite holds.
The usual SD card socket has a mechanical switch which is grounded as
soon as a card is inserted.
Of course there might be some board logic which inverts the signal, but
as far as current users are concerned, there is no such logic.
Current U-Boot users either not using the CD functionality, or have a
different way (e.g. external to SoC GPIO controller) for checking the
card presence.
This patch also brings the polarity assumption in line with the Linux
kernel and adds appropriate comments.
This patch also might spare issues once the TWL GPIO driver will be
converted to the DM.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Dmitry Lifshitz <lifshitz@compulab.co.il>
Reviewed-by: Tom Rini <trini@ti.com>
Igor Grinberg [Mon, 3 Nov 2014 09:32:22 +0000 (11:32 +0200)]
omap3: cm-t35: move get_board_serial() fallback
The fallback is used for cases when CONFIG_SERIAL_TAG defined, but the
eeprom is not used.
The fallback is useful for more than one CompuLab board, so move it to a
common location.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Reviewed-by: Tom Rini <trini@ti.com>
Igor Grinberg [Mon, 3 Nov 2014 09:32:21 +0000 (11:32 +0200)]
omap3: cm-t35: move the SMC911x code
Extract the SMC911x initialization code to a common location where it
can be reused by other compulab omap3 based boards.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Reviewed-by: Tom Rini <trini@ti.com>
Igor Grinberg [Mon, 3 Nov 2014 09:32:20 +0000 (11:32 +0200)]
omap3: cm-t35: extract the splash code from board
The splash screen loading code can be reused by other compulab boards.
For now extract it to a common location for further reuse.
This also switches the splash code dependency from CONFIG_LCD to
CONFIG_SPLASH_SCREEN as it should normally be.
In addition this patch fixes the accidental dependency of the
get_board_mem_timings() function on CONFIG_LCD, by just moving the
splash code and leaving the above function intact.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Reviewed-by: Tom Rini <trini@ti.com>
Igor Grinberg [Mon, 3 Nov 2014 09:32:19 +0000 (11:32 +0200)]
omap3: cm-t35: move the USB hub reset code
Extract the USB hub reset code to a common location where it can be
reused by other compulab boards.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Reviewed-by: Tom Rini <trini@ti.com>
Igor Grinberg [Mon, 3 Nov 2014 09:32:18 +0000 (11:32 +0200)]
compulab: refactor board revision handling
Move board revision handling code to a common location
for further reuse.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Reviewed-by: Tom Rini <trini@ti.com>
Igor Grinberg [Wed, 5 Nov 2014 11:29:54 +0000 (13:29 +0200)]
am335x: make get_board_rev() function weak
Current get_board_rev() function returns a hard coded value which is
obviously incorrect for the majority of boards.
Allow boards to provide a correct implementation by making this
function weak.
In addition open code the trivial and useless BOARD_REV_ID define and
adjust the comment.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Cc: Tom Rini <trini@ti.com>
Heiko Schocher [Wed, 5 Nov 2014 09:23:21 +0000 (10:23 +0100)]
arm: am335x: net: pxm2: disable rgmii internal delay mode
disable internal delay through gmii_sel register, as this
is done in the ar8031 phy.
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Tom Rini <trini@ti.com>
Khoronzhuk, Ivan [Tue, 4 Nov 2014 18:48:47 +0000 (20:48 +0200)]
ks2_evm: board: remove sprintf for simple string
There is no reason to sprintf simple string.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Khoronzhuk, Ivan [Tue, 4 Nov 2014 16:06:27 +0000 (18:06 +0200)]
ks2_evm: config: enable fatload command
The keystone2 evm can boot from USB partition with FAT32 FS, so
enable generic load command and fatload command usage.
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
Khoronzhuk, Ivan [Tue, 4 Nov 2014 14:52:35 +0000 (16:52 +0200)]
keystone2: config: align names of images with MCSDK
The Multicore Software Development Kit (MCSDK) provides foundational
software for TI KeyStone II device platforms. It's supposed to be used
with uboot, and it's convenient to have the same names for images, so
correct environment image names according to the last MCSDK3.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
Murali Karicheri [Tue, 4 Nov 2014 14:52:34 +0000 (16:52 +0200)]
keystone2: config: restructure handling of default env settings
Currently to customize env for various ks2 boards, individual
variables such as NAME_FS etc are defined and included in the
common config.h to define CONFIG_EXTRA_ENV_SETTINGS. This
doesn't scale well if a variable is not applicable on a
specific board. Using this scheme, we have to define variables
with empty value and it's ugly. Instead, to allow board specific
customization of default env variable, define a common
CONFIG_EXTRA_ENV_KS2_SETTINGS for all common variables and define
board specific variables in individual board specific config.h
using CONFIG_EXTRA_ENV_KS2_BOARD_SETTINGS. Use the common and board
specific variables to define CONFIG_EXTRA_ENV_SETTINGS. This way
more variables can be added in future for individual boards
without affecting the other config.h files.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
Khoronzhuk, Ivan [Mon, 3 Nov 2014 23:39:27 +0000 (01:39 +0200)]
dma: keystone_nav: remove spurious qm_cfg verification
The verification qm_cfg existence is done at ksnav_init().
So, there is no need to verify it after initialization.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
Murali Karicheri [Mon, 3 Nov 2014 16:09:52 +0000 (18:09 +0200)]
keystone2: change default boot mode to ubi
To allow out of box demo, change default boot mode to ubi
boot now that NAND is functional in latest EVMs.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
Khoronzhuk, Ivan [Mon, 3 Nov 2014 16:09:51 +0000 (18:09 +0200)]
ks2_evm: configs: fix UBI volume name
The UBI volume name has to be prefixed with "ubi:".
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
Guillaume GARDET [Mon, 3 Nov 2014 13:26:18 +0000 (14:26 +0100)]
ARM: TI: omap3: remove raw initrd support in omap3_igep00x0 config file since it is now in ti_armv7_common.h
Signed-off-by: Guillaume GARDET <guillaume.gardet@free.fr>
Cc: Tom Rini <trini@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
Guillaume GARDET [Mon, 3 Nov 2014 13:26:17 +0000 (14:26 +0100)]
ARM: TI: Enable raw initrd support
Signed-off-by: Guillaume GARDET <guillaume.gardet@free.fr>
Cc: Tom Rini <trini@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
Hao Zhang [Thu, 30 Oct 2014 16:59:43 +0000 (18:59 +0200)]
net: phy: marvell: add errata w/a for 88E151* chips
As per Marvell Release Notes - Alaska 88E1510/88E1518/88E1512/88E1514
Rev A0, Errata Section 3.1 Marvell PHY has an errata which requires
that certain registers get written in order to restart
autonegotiation.
Signed-off-by: Hao Zhang <hzhang@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Tom Rini [Wed, 5 Nov 2014 18:11:18 +0000 (13:11 -0500)]
Merge branch 'rmobile' of git://denx.de/git/u-boot-sh
Khoronzhuk, Ivan [Wed, 29 Oct 2014 11:21:22 +0000 (13:21 +0200)]
ks2_evm: readme: add k2l evm board information
Currently Keystone2 Lamar evm (K2L) board is added, so update
Keystone2 readme file to have such one.
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Hao Zhang [Wed, 29 Oct 2014 11:09:34 +0000 (13:09 +0200)]
board: k2l_evm: add network support
This patch adds network support code and enables keystone_net
driver usage for k2l_evm evaluation board.
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Hao Zhang <hzhang@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Khoronzhuk, Ivan [Wed, 29 Oct 2014 11:09:33 +0000 (13:09 +0200)]
net: keystone_net: add Keystone2 K2L SoC support
The Keystone2 Lamar SoC uses the same keystone net driver.
This patch adds opportunity to use it by K2L SoCs.
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Khoronzhuk, Ivan [Wed, 29 Oct 2014 11:09:32 +0000 (13:09 +0200)]
net: keystone_serdes: add keystone K2L SoC support
Keystone2 Lamar SoC uses the same keystone SerDes driver.
All Keystone2 EVM boards currently use SerDes driver, so move
CONFIG_TI_KEYSTONE_SERDES to common configuration file.
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Khoronzhuk, Ivan [Wed, 29 Oct 2014 11:09:31 +0000 (13:09 +0200)]
ARM: keystone2: keysonte_nav: add support for K2L SoC
The Keystone2 Lamar SoC uses the same keystone navigator.
Move queue numbers to common hardware file, as all Keystone2 SoCs
have the same ones.
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Dileep Katta [Tue, 28 Oct 2014 23:37:11 +0000 (05:07 +0530)]
Enable Android Fastboot support on am335x_evm board
Signed-off-by: Dileep Katta <dileep.katta@linaro.org>
[trini: Rework so that am335x_evm_usbspl still builds]
Signed-off-by: Tom Rini <trini@ti.com>
Tom Rini [Wed, 5 Nov 2014 17:48:09 +0000 (12:48 -0500)]
Merge branch 'master' of git://denx.de/git/u-boot-imx
Paul Kocialkowski [Tue, 28 Oct 2014 15:10:59 +0000 (16:10 +0100)]
twl4030: More voltages on VAUX2 and VAUX3
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Tom Rini [Mon, 27 Oct 2014 20:15:08 +0000 (16:15 -0400)]
am335x_evm: Convert NOR_BOOT to Kconfig
Signed-off-by: Tom Rini <trini@ti.com>
Tom Rini [Mon, 27 Oct 2014 20:15:07 +0000 (16:15 -0400)]
am335x_evm: Add NOR to Kconfig
Make enabling support for NOR (and describe where it's seen) be done via
Kconfig.
Signed-off-by: Tom Rini <trini@ti.com>
Nikita Kiryanov [Wed, 29 Oct 2014 15:56:22 +0000 (17:56 +0200)]
arm: mx6: cm_fx6: detect 1GB DRAM correctly on solo
The 1GB DRAM configuration on mx6 solo uses 2 chip selects, but
the code tests 1GB DRAM configuration as if it is all present on one
chip select, and thus cannot see the full range of available memory.
Refactor the check to detect 1GB DRAM correctly.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Nikita Kiryanov [Wed, 29 Oct 2014 15:56:21 +0000 (17:56 +0200)]
arm: mx6: cm_fx6: change issd gpio order
Change the order in which GPIOs are toggled in SATA init sequence to
accomodate both SanDisk and Phison SSDs.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Tom Rini [Wed, 5 Nov 2014 12:23:32 +0000 (07:23 -0500)]
Merge git://www.denx.de/git/u-boot-sunxi
Tom Rini [Wed, 5 Nov 2014 12:12:16 +0000 (07:12 -0500)]
Merge git://www.denx.de/git/u-boot-ppc4xx
Hans de Goede [Fri, 31 Oct 2014 16:04:52 +0000 (17:04 +0100)]
dm: sunxi: Request USB vbus gpio
This is necessary for the device-model enabled builds to work properly.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Simon Glass <sjg@chromium.org>
Hans de Goede [Fri, 31 Oct 2014 15:55:02 +0000 (16:55 +0100)]
dm: sunxi: Request card detect gpio
This is necessary for the device-model enabled builds to work properly.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Simon Glass <sjg@chromium.org>
Simon Glass [Fri, 31 Oct 2014 02:25:50 +0000 (20:25 -0600)]
dm: sunxi: Add support for serial using driver model
Add a driver for the designware serial UART used on sunxi. This just
redirects to the normal ns16550 driver.
Add a stdout-path to the device tree so that the correct UART is chosen.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Simon Glass [Fri, 31 Oct 2014 02:25:49 +0000 (20:25 -0600)]
dm: sunxi: Modify the GPIO driver to support driver model
This adds driver model support to the sunxi GPIO driver, using the device
tree to trigger binding of the driver. The driver will still operate
without driver model too.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Simon Glass [Fri, 31 Oct 2014 02:25:48 +0000 (20:25 -0600)]
dm: sunxi: Make sure that GPIOs are requested
The scsi_init() function uses a GPIO so should request it. There is no
way to return an error here, and the request may be made multiple times,
so just ignore errors for now.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Simon Glass [Fri, 31 Oct 2014 02:25:47 +0000 (20:25 -0600)]
dm: sunxi: Add pinmux functions which take a bank parameter
With driver model we will have access to a bank pointer, so we want to
use it rather than converting back to a number, and then back to a
bank pointer. Add functions to provide this feature.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>