platform/kernel/u-boot.git
10 years agovexpress/armv8: Fix incorrect ethernet controller
Bhupesh Sharma [Thu, 16 Jan 2014 15:47:40 +0000 (09:47 -0600)]
vexpress/armv8: Fix incorrect ethernet controller

This patch enables ethernet support in ARMv8 foundation model. The ARMv8
foundation model supports a SMSC91C111 integrated MAC and PHY module
which is present at base address 0x01A000000.

The previous implementation had enabled SMSC9115 ethernet controller
which is not present on the ARMv8 foundation model.

Tested on ARMv8 foundation model v1 and v2 by running ping/tftp
between the foundation model and the host PC via a bridged network.

Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
10 years agoARM: trats2: dfu: Enable default Poll Timeout for Trats2 board
Łukasz Majewski [Tue, 14 Jan 2014 07:02:25 +0000 (08:02 +0100)]
ARM: trats2: dfu: Enable default Poll Timeout for Trats2 board

Provide default Poll Timeout value for Trats2 board.

Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Acked-by: Minkyu Kang <mk7.kang@samsung.com>
10 years agoconfig: Update envs for trats and trats2 - Disable L2 cache
Łukasz Majewski [Tue, 14 Jan 2014 07:02:26 +0000 (08:02 +0100)]
config: Update envs for trats and trats2 - Disable L2 cache

Disable L2 caches for Trats and Trats2 devices.

It turns out that for data downloading with thordown command L2 cache
disablement brings a significant speed improvement.

rootfs - 400 MiB:
- L2 cache enabled: 2.69 MiB/s
- L2 cache disabled:  5.56 MiB/s

Such improvement is possible due to reduction of the need to invalidate
redundant data, which resides in L2 cache.

Since the sent USB request size at once is 512B (L1 - 32 KiB in total) -
one can be quite confident that it is already available in L1 and L2 can
be disabled.

Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Acked-by: Minkyu Kang <mk7.kang@samsung.com>
10 years agoconfig: Update envs for trats and trats2 - new entries for new partitions
Łukasz Majewski [Tue, 14 Jan 2014 07:02:24 +0000 (08:02 +0100)]
config: Update envs for trats and trats2 - new entries for new partitions

This patch adds extra dfu_alt_info entries to support storing the whole BOOT
, DATA and UMS partitions.
This allows upgrade of uImage and device tree blob (dtb) files at once.

Now it is also possible to store ext4 rootfs prepared with well established
linux tools (like mkfs.ext4).

Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Acked-by: Minkyu Kang <mk7.kang@samsung.com>
10 years agoMerge branch 'master' of git://git.denx.de/u-boot-arm
Tom Rini [Thu, 16 Jan 2014 18:50:16 +0000 (13:50 -0500)]
Merge branch 'master' of git://git.denx.de/u-boot-arm

10 years agoarm: koelsch: Add support QSPI device and enable boot from SPI flash
Nobuhiro Iwamatsu [Wed, 8 Jan 2014 01:32:24 +0000 (10:32 +0900)]
arm: koelsch: Add support QSPI device and enable boot from SPI flash

This supports SH-QSPI device on koelsch board, and enable booting from
SPI flash.

Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
10 years agoarm: lager: Add support QSPI device and enable boot from SPI flash
Nobuhiro Iwamatsu [Wed, 8 Jan 2014 01:32:22 +0000 (10:32 +0900)]
arm: lager: Add support QSPI device and enable boot from SPI flash

This supports SH-QSPI device on lager board, and enable booting from
SPI flash.

Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
10 years agospi: sh_qspi: Add header file that defines the address of registers
Nobuhiro Iwamatsu [Wed, 8 Jan 2014 01:16:25 +0000 (10:16 +0900)]
spi: sh_qspi: Add header file that defines the address of registers

Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
10 years agoarm: rmobile: Add SH QSPI base register address
Nobuhiro Iwamatsu [Wed, 8 Jan 2014 01:14:26 +0000 (10:14 +0900)]
arm: rmobile: Add SH QSPI base register address

This adds base register address of SH QSPI.
Currently, SH QSPI is used only from R8A7790 and R8A7791.

Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
10 years agoarm: lager: Disable TMU0 before OS boot
Nobuhiro Iwamatsu [Fri, 11 Oct 2013 06:00:37 +0000 (15:00 +0900)]
arm: lager: Disable TMU0 before OS boot

On U-boot uses TMU0 as timer, but TMU0 does not use on linux kernel
and other.
This disables TMU0 at the request of from kernel user.

Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
10 years agoarm: koelsch: Disable TMU0 before OS boot
Nobuhiro Iwamatsu [Fri, 11 Oct 2013 05:49:04 +0000 (14:49 +0900)]
arm: koelsch: Disable TMU0 before OS boot

On U-boot uses TMU0 as timer, but TMU0 does not use on linux kernel
and other.
This disables TMU0 at the request of from kernel user.

Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
10 years agoMerge branch 'u-boot-imx/master' into 'u-boot-arm/master'
Albert ARIBAUD [Wed, 15 Jan 2014 14:18:04 +0000 (15:18 +0100)]
Merge branch 'u-boot-imx/master' into 'u-boot-arm/master'

10 years agomx6: Add initial support for the Hummingboard solo
Fabio Estevam [Fri, 3 Jan 2014 17:55:58 +0000 (15:55 -0200)]
mx6: Add initial support for the Hummingboard solo

SolidRun has designed the Hummingboard board based on mx6q/dl/solo.

Add the initial support for the mx6 solo variant.

More information about this hardware can be found at:
http://imx.solid-run.com/wiki/index.php?title=Carrier-One_Hardware

(Carrier-One was the previous name of Hummingboard).

Based on the work from Jon Nettleton <jon.nettleton@gmail.com>.

Signed-off-by: Jon Nettleton <jon.nettleton@gmail.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
10 years agomx6: clock: Pass the frequency as argument of enable_fec_anatop_clock()
Fabio Estevam [Fri, 3 Jan 2014 17:55:57 +0000 (15:55 -0200)]
mx6: clock: Pass the frequency as argument of enable_fec_anatop_clock()

Provide an argument to enable_fec_anatop_clock() to specify the clock frequency
that will be generated.

No changes are made to mx6slevk, which uses the default 50MHz fec clock.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
10 years agoMerge branch 'master' of git://git.denx.de/u-boot-arm
Tom Rini [Tue, 14 Jan 2014 19:48:42 +0000 (14:48 -0500)]
Merge branch 'master' of git://git.denx.de/u-boot-arm

10 years agoMerge branch 'master' of git://git.denx.de/u-boot-net
Tom Rini [Tue, 14 Jan 2014 19:39:53 +0000 (14:39 -0500)]
Merge branch 'master' of git://git.denx.de/u-boot-net

10 years agonet: phy: atheros: Fix the masks for AR8031/8035
Fabio Estevam [Fri, 3 Jan 2014 17:55:59 +0000 (15:55 -0200)]
net: phy: atheros: Fix the masks for AR8031/8035

Use the same masks as used in the kernel:
https://git.kernel.org/cgit/linux/kernel/git/stable/linux-stable.git/tree/drivers/net/phy/at803x.c?id=refs/tags/v3.12.6

With such changes Ethernet is functional on hummingboard solo.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Marek Vasut <marex@denx.de>
Patch: 306640

10 years agommc: dwmmc: mode change to 0644
Minkyu Kang [Tue, 14 Jan 2014 09:00:51 +0000 (18:00 +0900)]
mmc: dwmmc: mode change to 0644

Don't know why but, file permission was changed

Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
10 years agocommon, env: optimize boottime
Heiko Schocher [Thu, 19 Dec 2013 12:45:04 +0000 (13:45 +0100)]
common, env: optimize boottime

when creating the hashtable, for each environmentvariable
getenv(ENV_CALLBACK_VAR) and getenv(ENV_FLAGS_VAR) is called,
which costs at this point a lot of time. So call this two
getenv() calls only once.

Boottime on the ids8313 board without this patch:

2013-12-19 13:38:22,894:  NAND:  128 MiB
2013-12-19 13:38:27,659:  In:    serial
(~4.8 sec)

Bootime with this patch on the ids8313 board:

2013-12-19 13:40:25,332:  NAND:  128 MiB
2013-12-19 13:40:25,546:  In:    serial
(~0.2 sec)

Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Wolfgang Denk <wd@denx.de>
10 years agoboard: nios2: Add CONFIG_CFI_FLASH_MTD guard to flash.h header include
Ezequiel Garcia [Fri, 20 Dec 2013 21:34:53 +0000 (18:34 -0300)]
board: nios2: Add CONFIG_CFI_FLASH_MTD guard to flash.h header include

Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
10 years agobootm: Reinstate special case for standalone images
Simon Glass [Thu, 26 Dec 2013 23:26:24 +0000 (16:26 -0700)]
bootm: Reinstate special case for standalone images

For standalone images, bootm had a special case where the OS boot function
was NULL but did actually exist. It was just called manually.

This was removed by commit 35fc84fa which checks for the non-existence of
this function before the special case is examined.

There is no obvious reason why standalone is handled with a special case.
Adjust the code so that standalone has a normal OS boot function. We still
need a special case for when the function returns, but at least we can
avoid the main problem.

This is intended to fix the reported:

    ERROR: booting os 'U-Boot' (17) is not supported

but needs testing.

Signed-off-by: Simon Glass <sjg@chromium.org>
10 years agofuelgauge: max17042: fix i2c read issue which causes infinity loop.
Przemyslaw Marczak [Mon, 30 Dec 2013 10:24:32 +0000 (11:24 +0100)]
fuelgauge: max17042: fix i2c read issue which causes infinity loop.

Issues:
- reading i2c data by passing u16 pointer causes errors in read data.
- max17042 status register fields have not only Power On Reset meaning
  so using proper mask is required.

Changes:
- read i2c data to type u32 instead of u16 - avoids buffer overflow
- compare FG status register using mask not just one bit value
- add checking return value to functions fg read/write
- add model lock and model check count
- add debug msg

Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
10 years agocommon/image.c: move VxWorks header string out of CONFIG_CMD_ELF
miao.yan@windriver.com [Fri, 27 Dec 2013 08:01:50 +0000 (16:01 +0800)]
common/image.c: move VxWorks header string out of CONFIG_CMD_ELF

Otherwise, when booting VxWorks kernel, the incorrect message will
be seen:

    ARM Unknown OS Kernel Image (uncompressed)

Signed-off-by: Miao Yan <miao.yan@windriver.com>
10 years agocommand.c: Fix auto-completion for the full commands list case
Andrew Gabbasov [Fri, 27 Dec 2013 16:05:14 +0000 (10:05 -0600)]
command.c: Fix auto-completion for the full commands list case

Compiling of full list of commands does not advance the counter,
so it always results in an empty list.
This seems to be (inadvertently?) introduced by commit
6c7c946cadfafdea80eb930e3181085b907a0362.

Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
10 years agolzma: fix buffer bound check error
Antonios Vamporakis [Tue, 31 Dec 2013 01:57:01 +0000 (02:57 +0100)]
lzma: fix buffer bound check error

Variable uncompressedSize references the space available, while outSizeFull is
the actual expected uncompressed size. Using the wrong value causes LzmaDecode
to return SZ_ERROR_INPUT_EOF. Problem was introduced in commit afca294. While
at it add additional debug message.

Signed-off-by: Antonios Vamporakis <ant@area128.com>
CC: Kees Cook <keescook@chromium.org>
CC: Simon Glass <sjg@chromium.org>
CC: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
CC: Luka Perkov <luka@openwrt.org>
10 years agoarm: use canonical sub mnemonic
Andreas Bießmann [Wed, 27 Nov 2013 15:09:29 +0000 (16:09 +0100)]
arm: use canonical sub mnemonic

Building some arm boards with older binutils may produce errors like this:

---8<---
crt0.S: Assembler messages:
crt0.S:70: Error: register expected, not '#(184)' -- `sub sp,#(184)'
--->8---

Use canonical version of the subtract mnemonic to avoid those issues.

Reported-by: Alexey Smishlayev <alexey@xtech2.lv>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
10 years agoMerge 'u-boot-imx/master' into 'u-boot-arm/master'
Albert ARIBAUD [Tue, 14 Jan 2014 10:50:54 +0000 (11:50 +0100)]
Merge 'u-boot-imx/master' into 'u-boot-arm/master'

10 years agoarm: put .hash, .got.plt and .machine_param back in binaries
Albert ARIBAUD [Mon, 13 Jan 2014 13:57:05 +0000 (14:57 +0100)]
arm: put .hash, .got.plt and .machine_param back in binaries

Some targets will build fine but not boot if sections .hash and
.got.plt are not present in the binary. Add them back.

Also, Exynos machines require .machine_param section in SPL.
Add it.

Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Tested-by: Rajeshwari S Shinde <rajeshwari.s@samsung.com>
10 years agomx1ads: remove board support
Albert ARIBAUD [Mon, 13 Jan 2014 20:06:17 +0000 (21:06 +0100)]
mx1ads: remove board support

Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Acked-by: Stefano Babic <sbabic@denx.de>
10 years agomini2440: remove board support
Albert ARIBAUD [Mon, 13 Jan 2014 20:06:16 +0000 (21:06 +0100)]
mini2440: remove board support

Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Acked-by: Minkyu Kang <mk7.kang@samsung.com>
10 years agoPrepare v2014.01-rc3 v2014.01-rc3
Tom Rini [Mon, 13 Jan 2014 19:36:17 +0000 (14:36 -0500)]
Prepare v2014.01-rc3

Signed-off-by: Tom Rini <trini@ti.com>
10 years agoMerge branch 'master' of git://git.denx.de/u-boot-arm
Tom Rini [Mon, 13 Jan 2014 18:50:25 +0000 (13:50 -0500)]
Merge branch 'master' of git://git.denx.de/u-boot-arm

10 years agoMerge branch 'master' of git://git.denx.de/u-boot-spi
Tom Rini [Mon, 13 Jan 2014 18:45:15 +0000 (13:45 -0500)]
Merge branch 'master' of git://git.denx.de/u-boot-spi

10 years agoMerge branch 'master' of git://git.denx.de/u-boot-video
Tom Rini [Mon, 13 Jan 2014 13:41:04 +0000 (08:41 -0500)]
Merge branch 'master' of git://git.denx.de/u-boot-video

10 years agoARM: pxa: Fix OneNAND window access on VPAC270
Marek Vasut [Wed, 25 Dec 2013 23:53:26 +0000 (00:53 +0100)]
ARM: pxa: Fix OneNAND window access on VPAC270

Access the OneNAND 1KiB window on the VPAC270 as an SRAM instead of accessing
it as a burst-RAM. This fixes a problem where the board failed to reboot
sometimes as the CPU couldn't start executing from the OneNAND 1KiB window.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
10 years agoARM: pxa: Fix OneNAND SPL builds
Marek Vasut [Wed, 25 Dec 2013 23:46:49 +0000 (00:46 +0100)]
ARM: pxa: Fix OneNAND SPL builds

The OneNAND SPL used on PXA is slightly obscure. Due to the OneNAND limitation,
where we have only the first 1KiB of the OneNAND available upon power-up as a
memory-mapped area, from which the CPU starts executing, we place only the most
essential code into this first 1KiB . This code copies the rest of the SPL into
SRAM and jumps to it. This code is stored in section .text.0 .

The rest of the SPL is stored in section .text.1 . When running the OBJCOPY on
the SPL, it will preserve only .text section, but the .text.0 and .text.1 are
stripped away from the result, thus making the SPL binary empty. The patch adds
additional -j parameters to the OBJCOPY for PXA during the SPL build, which will
preserve the .text.0 and .text.1 sections.

Moreover, this patch also adds missing functions into the .text.0 section, since
otherwise the PXA270 with 1KiB-window OneNAND won't be able to boot.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
10 years agousb: ums: wait for usb cable connection before enter ums mode
Przemyslaw Marczak [Tue, 7 Jan 2014 14:08:37 +0000 (15:08 +0100)]
usb: ums: wait for usb cable connection before enter ums mode

Before this change ums mode can not be entered when device
was using the same usb port for usb/uart communication.
Switching USB cable from UART to USB always causes ums exit.

Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
10 years agousb: exynos5: arndale: Add network support
Inderpal Singh [Wed, 8 Jan 2014 03:49:57 +0000 (09:19 +0530)]
usb: exynos5: arndale: Add network support

Arndale board has AX88760, which is USB 2.0 Hub & USB 2.0 Ethernet Combo
controller, connected to HSIC Phy of USB host controller via USB3503 hub.

This patch uses board specific board_usb_init function to perform reset
sequence for USB3503 hub and enables the relevant config options for
network to work.

Signed-off-by: Inderpal Singh <inderpal.singh@linaro.org>
Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org>
10 years agousb: ehci: exynos: set/reset hsic phys
Inderpal Singh [Wed, 8 Jan 2014 03:49:56 +0000 (09:19 +0530)]
usb: ehci: exynos: set/reset hsic phys

The controller has 3 ports. The port0 is for USB 2.0 Phy, port1 and port2
are for HSIC phys. The usb 2.0 phy is already being setup. This patch
sets up the hsic phys.

Signed-off-by: Inderpal Singh <inderpal.singh@linaro.org>
10 years agousb: gadget: fotg210: EP0 fifo empty indication is non-reliable
Kuo-Jung Su [Fri, 20 Dec 2013 04:33:00 +0000 (12:33 +0800)]
usb: gadget: fotg210: EP0 fifo empty indication is non-reliable

The fifo size of ep0 is 64 bytes, and if the packet size grater than
64 bytes, the driver would have to fill up the fifo multiple times,
and before filling up the fifo, the driver should make sure the fifo
is empty by checking fifo empty indication.

However there is a hardware bug that the fifo empty indication is
somehow a bit earlier than fifo reset. So if I don't add an extra
delay here, the data might be corrupted. (i.e., 1 byte missing)

After a couple of tests, it truns out that 1 usec is good enough.

This workaround should be applied to all hardware revisions.

Signed-off-by: Kuo-Jung Su <dantesu@faraday-tech.com>
CC: Marek Vasut <marex@denx.de>
10 years agousb: gadget: fotg210: add w1c interrupt status support
Kuo-Jung Su [Fri, 20 Dec 2013 04:32:59 +0000 (12:32 +0800)]
usb: gadget: fotg210: add w1c interrupt status support

Since hardware revision 1.11.0, the following interrupt status
registers are now W1C (i.e., write 1 clear):

1. Interrupt Source Group 0 Register (0x144) (EP0 Abort: BIT5)
2. Interrupt Source Group 2 Register (0x14C) (All bits)

And before revision 1.11.0, these registers are all R/W.
Which means software must write a 0 to clear the status.

Signed-off-by: Kuo-Jung Su <dantesu@faraday-tech.com>
CC: Marek Vasut <marex@denx.de>
10 years agomx6slevk: Include "mx6_common.h"
Fabio Estevam [Thu, 9 Jan 2014 10:57:12 +0000 (08:57 -0200)]
mx6slevk: Include "mx6_common.h"

Include "mx6_common.h" so that some ARM errata are applied and also the
vddsoc regulator can be changed.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
10 years agoimx6: make use of lldiv(..)
Christian Gmeiner [Wed, 8 Jan 2014 07:24:25 +0000 (08:24 +0100)]
imx6: make use of lldiv(..)

Commit 762a88ccf8540948fbf8c31b40a29d1e0684a25b introduces
a 64-bit division without using the lldiv() function,
which pulls in previously unused libgcc stuff.

Signed-off-by: Måns Rullgård <mans@mansr.com>
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Acked-by: Stefano Babic <sbabic@denx.de>
10 years agowandboard: Set default environment to use zImage
John Weber [Mon, 6 Jan 2014 15:27:22 +0000 (13:27 -0200)]
wandboard: Set default environment to use zImage

Change the default environment to use zImage instead of uImage, this
requires changes to the default environment to load a file named
zImage instead of uImage, and to use the 'bootz' command instead of
'bootm' when booting the kernel.

The zImage works for FSL Linux's kernel fork versions 3.0.35, 3.10.9,
and 3.10.17; this also works fine for mainline kernels.

Signed-off-by: John Weber <rjohnweber@gmail.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
10 years agomx6sabresd: Add eMMC specific environment to allow U-Boot update
Otavio Salvador [Mon, 6 Jan 2014 15:27:20 +0000 (13:27 -0200)]
mx6sabresd: Add eMMC specific environment to allow U-Boot update

A new 'update_emmc_firmware' target is added to allow for easy U-Boot
update in the eMMC as it has secury boot partition and this needs
specific handling on how to program the specific partition.

Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
10 years agomx6slevk: Return from cpu_eth_init() directly
Fabio Estevam [Sat, 4 Jan 2014 19:36:33 +0000 (17:36 -0200)]
mx6slevk: Return from cpu_eth_init() directly

There is no need to print an error message when cpu_eth_init() fails because
net/eth.c already prints it.

In order to simplify the code, just return the value from cpu_eth_init(bis)
directly.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
10 years agomx6sabresd: Return from cpu_eth_init() directly
Fabio Estevam [Sat, 4 Jan 2014 19:36:32 +0000 (17:36 -0200)]
mx6sabresd: Return from cpu_eth_init() directly

There is no need to print an error message when cpu_eth_init() fails because
net/eth.c already prints it.

In order to simplify the code, just return the value from cpu_eth_init(bis)
directly.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
10 years agomx6qsabreauto: Return from cpu_eth_init() directly
Fabio Estevam [Sat, 4 Jan 2014 19:36:31 +0000 (17:36 -0200)]
mx6qsabreauto: Return from cpu_eth_init() directly

There is no need to print an error message when cpu_eth_init() fails because
net/eth.c already prints it.

In order to simplify the code, just return the value from cpu_eth_init(bis)
directly.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
10 years agomx6qarm2: Remove unneeded error message when cpu_eth_init() fails
Fabio Estevam [Sat, 4 Jan 2014 19:36:30 +0000 (17:36 -0200)]
mx6qarm2: Remove unneeded error message when cpu_eth_init() fails

There is no need to print an error message when cpu_eth_init() fails because
net/eth.c already prints it.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
10 years agotitanium: Return from cpu_eth_init() directly
Fabio Estevam [Sat, 4 Jan 2014 19:36:29 +0000 (17:36 -0200)]
titanium: Return from cpu_eth_init() directly

There is no need to print an error message when cpu_eth_init() fails because
net/eth.c already prints it.

In order to simplify the code, just return the value from cpu_eth_init(bis)
directly.

Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefan Roese <sr@denx.de>
10 years agowandboard: Return from cpu_eth_init() directly
Fabio Estevam [Sat, 4 Jan 2014 19:36:28 +0000 (17:36 -0200)]
wandboard: Return from cpu_eth_init() directly

There is no need to print an error message when cpu_eth_init() fails because
net/eth.c already prints it.

In order to simplify the code, just return the value from cpu_eth_init(bis)
directly.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
10 years agovideo: ipu reg: Correct reserved array size in struct ipu_idmac
Liu Ying [Sun, 22 Dec 2013 05:02:42 +0000 (13:02 +0800)]
video: ipu reg: Correct reserved array size in struct ipu_idmac

The array reserved as a placeholder in the structure ipu_idmac
should contain 44 32bit unsigned integer entries instead of 45
ones, because the placeholder is located bewteen the register
IDMAC_SC_CORD1 and the register IDMAC_CH_BUSY_1 with the address
offsets of 0x804c and 0x8100 respectively.

Reported-by: Robin Gong <b38343@freescale.com>
Acked-by: Robin Gong <b38343@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Liu Ying <Ying.Liu@freescale.com>
10 years agovideo: ipu reg: Correct reserved1 array size in struct ipu_cm
Liu Ying [Sun, 22 Dec 2013 05:02:41 +0000 (13:02 +0800)]
video: ipu reg: Correct reserved1 array size in struct ipu_cm

The array reserved1 as a placeholder in the structure ipu_cm
should contain 4 32bit unsigned integer entries instead of 16
ones, because the placeholder is located bewteen the register
IPU_CH_DB_MODE_SEL_1 and the register IPU_ALT_CH_DB_MODE_SEL_0
with the address offsets of 0x154 and 0x168 respectively.

Reported-by: Robin Gong <b38343@freescale.com>
Acked-by: Robin Gong <b38343@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Liu Ying <Ying.Liu@freescale.com>
10 years agosf: params: Removed flag SECT_4K for Micron N25Q128
Siva Durga Prasad Paladugu [Wed, 8 Jan 2014 05:57:07 +0000 (11:27 +0530)]
sf: params: Removed flag SECT_4K for Micron N25Q128

Remove the flag SECT_4K for device N25Q128 as the 4K-byte
sub sector erase granularity is available only for top/bottom
8 sectors in some of the N25Q128 chips.

Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
10 years agodoc: SPI: Update status.txt
Jagannadha Sutradharudu Teki [Wed, 8 Jan 2014 17:34:44 +0000 (23:04 +0530)]
doc: SPI: Update status.txt

Updated current SPI subsyetem status.

Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
10 years agosf: Add CONFIG_SF_DUAL_FLASH
Jagannadha Sutradharudu Teki [Sat, 11 Jan 2014 09:55:04 +0000 (15:25 +0530)]
sf: Add CONFIG_SF_DUAL_FLASH

This config will use for defining greater than single flash support.
currently - DUAL_STACKED and DUAL_PARALLEL.

Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
10 years agosf: Add dual memories support - DUAL_PARALLEL
Jagannadha Sutradharudu Teki [Mon, 6 Jan 2014 18:41:35 +0000 (00:11 +0530)]
sf: Add dual memories support - DUAL_PARALLEL

This patch added support for accessing dual memories in
parallel connection with single chipselect line from controller.

For more info - see doc/SPI/README.dual-flash

Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
10 years agosf: Add dual memories support - DUAL_STACKED
Jagannadha Sutradharudu Teki [Sun, 12 Jan 2014 16:10:11 +0000 (21:40 +0530)]
sf: Add dual memories support - DUAL_STACKED

This patch added support for accessing dual memories in
stacked connection with single chipselect line from controller.

For more info - see doc/SPI/README.dual-flash

Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
10 years agosf: ops: Unify read_ops bank configuration
Jagannadha Sutradharudu Teki [Sat, 11 Jan 2014 11:27:07 +0000 (16:57 +0530)]
sf: ops: Unify read_ops bank configuration

Unified the bar code from read_ops into a spi_flash_bar()

Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
10 years agosf: Code cleanups
Jagannadha Sutradharudu Teki [Sun, 12 Jan 2014 16:08:21 +0000 (21:38 +0530)]
sf: Code cleanups

- comment typo's
- func args have a proper names

Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
10 years agosf: Divide flash register ops from QEB code
Jagannadha Sutradharudu Teki [Mon, 30 Dec 2013 16:46:23 +0000 (22:16 +0530)]
sf: Divide flash register ops from QEB code

QEB code comprises of couple of flash register read/write operations,
this patch moved flash register operations on to sf_op

Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
10 years agosf: probe: Enable macronix quad read/write cmds support
Jagannadha Sutradharudu Teki [Thu, 26 Dec 2013 08:46:50 +0000 (14:16 +0530)]
sf: probe: Enable macronix quad read/write cmds support

Added macronix flash quad read/write commands support and
it's up to the respective controller driver usecase to
configure the respective commands by defining SPI RX/TX
operation modes from include/spi.h on the driver.

Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
10 years agosf: Add macronix set QEB support
Jagannadha Sutradharudu Teki [Thu, 26 Dec 2013 08:43:36 +0000 (14:13 +0530)]
sf: Add macronix set QEB support

This patch adds set QEB support for macronix flash devices
which are trying to program/read quad operations.

Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
10 years agosf: Discover read dummy_byte
Jagannadha Sutradharudu Teki [Sat, 11 Jan 2014 11:20:45 +0000 (16:50 +0530)]
sf: Discover read dummy_byte

Discovered the read dummy_byte based on the
configured read command.

Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
10 years agosf: Add QUAD_IO_FAST read support
Jagannadha Sutradharudu Teki [Tue, 24 Dec 2013 09:54:31 +0000 (15:24 +0530)]
sf: Add QUAD_IO_FAST read support

This patch adds support QUAD_IO_FAST read command.

Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
10 years agosf: Separate the flash params table
Jagannadha Sutradharudu Teki [Mon, 23 Dec 2013 18:04:42 +0000 (23:34 +0530)]
sf: Separate the flash params table

Moved the flash params table from sf_probe.c and
placed on to sf_params.c, hence flash params file will
alter based on new addons.

Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
10 years agosf: probe: Enable RD_FULL and WR_QPP
Jagannadha Sutradharudu Teki [Mon, 23 Dec 2013 11:09:06 +0000 (16:39 +0530)]
sf: probe: Enable RD_FULL and WR_QPP

This patch enabled RD_FULL and WR_QPP for supported flashes
in micron, winbond and spansion.

Remaining parts will be add in future patches.

Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
10 years agosf: Set quad enable bit support
Jagannadha Sutradharudu Teki [Thu, 26 Dec 2013 08:24:57 +0000 (13:54 +0530)]
sf: Set quad enable bit support

This patch provides support to set the quad enable bit on flash.

quad enable bit needs to set before performing any quad IO
operations on respective SPI flashes.

Currently added set  quad enable bit for winbond and spansion flash
devices. stmicro flash doesn't require to set as qeb is volatile.
remaining flash devices support will add in future patches.

Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
10 years agosf: ops: Add configuration register writing support
Jagannadha Sutradharudu Teki [Mon, 23 Dec 2013 10:17:48 +0000 (15:47 +0530)]
sf: ops: Add configuration register writing support

This patch provides support to program a flash config register.

Configuration register contains the control bits used to configure
the different configurations and security features of a device.

Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
10 years agosf: Add quad read/write commands support
Jagannadha Sutradharudu Teki [Sat, 11 Jan 2014 09:43:11 +0000 (15:13 +0530)]
sf: Add quad read/write commands support

This patch add quad commands support like
- QUAD_PAGE_PROGRAM => for write program
- QUAD_OUTPUT_FAST ->> for read program

Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
10 years agosf: Add extended read commands support
Jagannadha Sutradharudu Teki [Sat, 11 Jan 2014 09:40:28 +0000 (15:10 +0530)]
sf: Add extended read commands support

Current sf uses FAST_READ command, this patch adds support to
use the different/extended read command.

This implementation will determine the fastest command by taking
the supported commands from the flash and the controller, controller
is always been a priority.

Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
10 years agospi: sh_spi: Use sh_spi_clear_bit() instead of open-coded
Axel Lin [Fri, 27 Dec 2013 05:51:55 +0000 (13:51 +0800)]
spi: sh_spi: Use sh_spi_clear_bit() instead of open-coded

We have a sh_spi_clear_bit() function, there's no reason not to use it.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Reviewed-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
10 years agosandbox: spi: Adjust 'sf test' to work on sandbox
Simon Glass [Sun, 10 Nov 2013 17:26:51 +0000 (10:26 -0700)]
sandbox: spi: Adjust 'sf test' to work on sandbox

Add map_sysmem() calls so that this test works correctly on sandbox.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Hung-ying Tyan <tyanh@chromium.org>
Reviewed-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
10 years agospi: Add Faraday SPI controller support
Kuo-Jung Su [Fri, 20 Dec 2013 07:24:30 +0000 (12:54 +0530)]
spi: Add Faraday SPI controller support

The Faraday FTSSP010 is a multi-function controller
which supports I2S/SPI/SSP/AC97/SPDIF. However This
patch implements only the SPI mode.

NOTE:
The DMA and CS/Clock control logic has been altered
since hardware revision 1.19.0. So this patch
would first detects the revision id of the underlying
chip, and then switch to the corresponding software
control routines.

Signed-off-by: Kuo-Jung Su <dantesu@faraday-tech.com>
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
CC: Tom Rini <trini@ti.com>
10 years agoMerge branch 'master' of git://git.denx.de/u-boot-arm
Tom Rini [Fri, 10 Jan 2014 15:56:00 +0000 (10:56 -0500)]
Merge branch 'master' of git://git.denx.de/u-boot-arm

Bringing in the MMC tree means that CONFIG_BOUNCE_BUFFER needed to be
added to include/configs/exynos5-dt.h now.

Conflicts:
include/configs/exynos5250-dt.h

Signed-off-by: Tom Rini <trini@ti.com>
10 years agodoc: Update the zynq u-boot status
Jagannadha Sutradharudu Teki [Wed, 8 Jan 2014 20:18:31 +0000 (01:48 +0530)]
doc: Update the zynq u-boot status

Updated doc/README.zynq to current status

Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
10 years agozynq: Enable CONFIG_DEFAULT_DEVICE_TREE
Jagannadha Sutradharudu Teki [Wed, 8 Jan 2014 20:18:30 +0000 (01:48 +0530)]
zynq: Enable CONFIG_DEFAULT_DEVICE_TREE

Enabled default dts files on respective pre-board config
files this is way MAKEALL will works. and it's upto user
to build specific dts by specifying at build time.

$ make zynq_zc70x_config
$ make -->  with default dts zynq-zc702.dts
or
$ make DEVICE_TREE=zynq-zc702 --> Same configuration with zynq-zc706.dts

Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
10 years agodts: zynq: Add more zynq dts files
Jagannadha Sutradharudu Teki [Wed, 8 Jan 2014 20:18:29 +0000 (01:48 +0530)]
dts: zynq: Add more zynq dts files

This patch adds initial dts support for supported
zynq boards.

Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
10 years agozynq-common: Enable verified boot(RSA)
Jagannadha Sutradharudu Teki [Wed, 8 Jan 2014 20:18:28 +0000 (01:48 +0530)]
zynq-common: Enable verified boot(RSA)

CONFIG_FIT_SIGNATURE - signature node support in FIT image
CONFIG_RSA - RSA lib support

Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
10 years agogpio: zynq: Add dummy gpio routines
Jagannadha Sutradharudu Teki [Wed, 8 Jan 2014 20:18:27 +0000 (01:48 +0530)]
gpio: zynq: Add dummy gpio routines

GPIO dummy routines are required for fdt build, may be removed
these dependencies once the u-boot fdt is fully optimized.

Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
10 years agodts: zynq: Add basic fdt support
Jagannadha Sutradharudu Teki [Wed, 8 Jan 2014 20:18:26 +0000 (01:48 +0530)]
dts: zynq: Add basic fdt support

This patch provides a basic fdt support for zynq u-boot.

zynq-7000.dtsi-> initial arch dts file
zynq-zed.dts -> initial zed board dts file
more devices should be added in subsequent patches.

u-boot build: once configuring of a board done
for building dtb with zynq-zed.dts as an input
zynq-uboot> make DEVICE_TREE=zynq-zed

Enabled CONFIG_OF_SEPARATE for building dtb separately.
There is a new binary called u-boot-dtb.bin which is a u-boot
with devicetree supported.

Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
10 years agozynq-common: Define CONFIG_ENV_OVERWRITE
Jagannadha Sutradharudu Teki [Wed, 8 Jan 2014 20:18:25 +0000 (01:48 +0530)]
zynq-common: Define CONFIG_ENV_OVERWRITE

Defined CONFIG_ENV_OVERWRITE, which allow to
overwrite serial baudrate and ethaddr.

Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
10 years agozynq-common: Define flash env. partition
Jagannadha Sutradharudu Teki [Wed, 8 Jan 2014 20:18:24 +0000 (01:48 +0530)]
zynq-common: Define flash env. partition

Last 128Kb sector of 1Mb flash is defined as u-boot
environment partition.

Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
10 years agozynq-common: Change Env. Sector size to 128Kb
Jagannadha Sutradharudu Teki [Wed, 8 Jan 2014 20:18:23 +0000 (01:48 +0530)]
zynq-common: Change Env. Sector size to 128Kb

Changed Env. Sector size from 0x10000 to 128Kb

Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
10 years agozynq-common: Define default environment
Jagannadha Sutradharudu Teki [Wed, 8 Jan 2014 20:18:22 +0000 (01:48 +0530)]
zynq-common: Define default environment

Defined default env. for autoboot FIT image from
respective boot devices.

Default settings:
fit_image=fit.itb
load_addr=0x2000000
fit_size=0x800000
flash_off=0x100000
nor_flash_off=0xE2100000

Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
10 years agozynq: Add support to find bootmode
Jagannadha Sutradharudu Teki [Wed, 8 Jan 2014 20:18:21 +0000 (01:48 +0530)]
zynq: Add support to find bootmode

Added support to find the bootmodes by reading
slcr bootmode register. this can be helpful to
autoboot the configurations w.r.t a specified bootmode.

Added this functionality on board_late_init as it's not
needed for normal initializtion part.

Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
10 years agozynq: Add zynq_zc770 xm012 board support
Jagannadha Sutradharudu Teki [Wed, 8 Jan 2014 20:18:20 +0000 (01:48 +0530)]
zynq: Add zynq_zc770 xm012 board support

ZC770 is a complete development board based on the Xilinx Zynq-7000
All Programmable SoC, similar to ZC70x board but which has four
different daughter cards, like XM010, XM011, XM012 and XM013

ZC770 XM012:
- 1GB DDR3
- 64MiB Numonyx NOR flash
- USB-UART

Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Cc: Stefan Roese <sr@denx.de>
10 years agozynq: Add zynq_zc770 xm013 board support
Jagannadha Sutradharudu Teki [Wed, 8 Jan 2014 20:18:19 +0000 (01:48 +0530)]
zynq: Add zynq_zc770 xm013 board support

ZC770 is a complete development board based on the Xilinx Zynq-7000
All Programmable SoC, similar to ZC70x board but which has four
different daughter cards, like XM010, XM011, XM012 and XM013

ZC770 XM013:
- 1GB DDR3
- 128 Mb Quad-SPI Flash(dual parallel)
- USB-UART

Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
10 years agozynq: Add zynq_zc770 xm010 board support
Jagannadha Sutradharudu Teki [Wed, 8 Jan 2014 20:18:18 +0000 (01:48 +0530)]
zynq: Add zynq_zc770 xm010 board support

ZC770 is a complete development board based on the Xilinx Zynq-7000
All Programmable SoC, similar to ZC70x board but which has four
different daughter cards, like XM010, XM011, XM012 and XM013

ZC770 XM010:
- 1Gb DDR3
- 1Mb SST SPI flash
- 128 Mb Quad-SPI Flash
- 8 Mb SST SI flash
- Full size SD/MMC card cage
- 10/100/1000 Ethernet
- USB-UART

Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
10 years agozynq: Add zynq microzed board support
Jagannadha Sutradharudu Teki [Wed, 8 Jan 2014 20:18:17 +0000 (01:48 +0530)]
zynq: Add zynq microzed board support

MicroZed is a low-cost development board based on
the Xilinx Zynq-7000 All Programmable SoC.

APSOC:
- XC7Z010-1CLG400C
Memory:
- 1 GB of DDR3 SDRAM
- 128Mb of QSPI flash(S25FL128SAGBHI200)
- Micro SD card interface
Communication:
- 10/100/1000 Ethernet
- USB 2.0
- USB-UART
User I/O:
- 100 User I/O (50 per connector)
- Configurable as up to 48 LVDS pairs or 100 single-ended I/O
Misc:
- Xilinx PC4 JTAG configuration port
- PS JTAG pins accessible via Pmod
- 33.33 MHz oscillator
- User LED and push switch

For more info - http://zedboard.org/product/microzed

Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
10 years agozynq: zc70x: Add Catalyst 24WC08 EEPROM config support
Jagannadha Sutradharudu Teki [Wed, 8 Jan 2014 20:18:16 +0000 (01:48 +0530)]
zynq: zc70x: Add Catalyst 24WC08 EEPROM config support

Adds configurations for Catalyst 24WC08 EEPROM, which
is present on the zynq boards.

Enable EEPROM support for zc70x boards.

Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
10 years agozynq-common: Define exact TEXT_BASE
Jagannadha Sutradharudu Teki [Wed, 8 Jan 2014 20:18:15 +0000 (01:48 +0530)]
zynq-common: Define exact TEXT_BASE

Defined TEXT_BASE for u-boot starts from 0x4000000
w.r.t zynq memory-map.

Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
10 years agozynq: Move CONFIG_SYS_SDRAM_SIZE to pre-board configs
Jagannadha Sutradharudu Teki [Wed, 8 Jan 2014 20:18:14 +0000 (01:48 +0530)]
zynq: Move CONFIG_SYS_SDRAM_SIZE to pre-board configs

CONFIG_SYS_SDRAM_SIZE is specific to a board hence moved
to specific pre-config board files.

Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
10 years agozynq: Add zynq zed board support
Jagannadha Sutradharudu Teki [Wed, 8 Jan 2014 20:18:13 +0000 (01:48 +0530)]
zynq: Add zynq zed board support

Zed is a complete development board based on the
Xilinx Zynq-7000 All Programmable SoC.

APSOC:
- XC7Z020-CLG484-1
Memory:
- 512 MB DDR3
- 256 Mb Quad-SPI Flash(
- Full size SD/MMC card cage
Connectivity:
- 10/100/1000 Ethernet
- USB OTG (Device/Host/OTG)
- USB-UART
Expansion:
- FMC (Low Pin Count)
- Pmod. headers (2x6)
Video/Display:
- HDMI output (1080p60 + audio)
- VGA connector
- 128 x 32 OLED
- User LEDs (9)
User inputs:
- Slide switches (8)
- Push button switches (7)
Audio:
- 24-bit stereo audio CODEC
- Stereo line in/out
- Headphone
- Microphone input
Analog:
- Xilinx XADC header
- Supports 4 analog inputs
- 2 Differential / 4 Single-ended
Debug:
- On-board USB JTAG programming port
- ARM Debug Access Port (DAP)

For more info - http://zedboard.org/product/zedboard

Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
10 years agozynq: Add zynq zc70x board support
Jagannadha Sutradharudu Teki [Wed, 8 Jan 2014 20:18:12 +0000 (01:48 +0530)]
zynq: Add zynq zc70x board support

The Zynq-7000 APSOC zc702 and zc706 enabled complte embedded
processing includes ASIC and FPGA design.

ZC702-:

APSOC:
- XC7Z020-CLG484-1
Memory:
- DDR3 Component Memory 1GB
- 16MB Quad SPI Flash
- IIC - 1 KB EEPROM
Connectivity:
- Gigabit Ethernet GMII, RGMII and SGMII.
- USB OTG - Host USB
- IIC Bus Headers/HUB
- 1 CAN with Wake on CAN
- USB-UART
Video/Display:
- HDMI Video OUT
- 8X LEDs
Control & I/O:
- 3 User Push Buttons
- 2 User Switches
- 8 User LEDs

For more info on zc702 board:
- http://www.xilinx.com/products/boards-and-kits/EK-Z7-ZC702-G.htm

ZC706-:

APSOC:
- XC7Z045 FFG900 -2 AP SoC
Memory:
- DDR3 Component Memory 1GB (PS)
- DDR3 SODIM Memory 1GB (PL)
- 2X16MB Quad SPI Flash (dual parallel)
- IIC - 1 KB EEPROM
Connectivity:
- PCIe Gen2x4
- SFP+ and SMA Pairs
- GigE RGMII Ethernet (PS)
- USB OTG 1 (PS) - Host USB
- IIC Bus Headers/HUB (PS)
- 1 CAN with Wake on CAN (PS)
- USB-UART
Video/Display:
- HDMI 8 color RGB 4.4.4 1080P-60 OUT
- HDMI IN 8 color RGB 4.4.4
Control & I/O:
- 2 User Push Buttons/Dip Switch, 2 User LEDs
- IIC access to GPIO
- SDIO (SD Card slot)
- 3 User Push Buttons, 2 User Switches, 8 User LEDs

For more info on zc706 board:
- http://www.xilinx.com/products/boards-and-kits/EK-Z7-ZC706-G.htm

Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
10 years agodoc: zynq: Add information on zynq u-boot
Jagannadha Sutradharudu Teki [Wed, 8 Jan 2014 20:18:11 +0000 (01:48 +0530)]
doc: zynq: Add information on zynq u-boot

Information on zynq u-boot about
- zynq boards
- mainline status
- TODO

Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
10 years agozynq-common: Rename zynq with zynq-common
Jagannadha Sutradharudu Teki [Wed, 8 Jan 2014 20:18:10 +0000 (01:48 +0530)]
zynq-common: Rename zynq with zynq-common

zynq.h -> zynq-common.h, zynq-common is Common
configuration options for all Zynq boards.

zynq.h is no longer exists hense removed from boards.cfg

Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
10 years agozynq: Add GEM0, GEM1 configs support
Jagannadha Sutradharudu Teki [Wed, 8 Jan 2014 20:18:09 +0000 (01:48 +0530)]
zynq: Add GEM0, GEM1 configs support

Zynq ethernet controller support two GEM's like
CONFIG_ZYNQ_GEM0 and CONFIG_ZYNQ_GEM1 enabled
both so-that the respective board will define
these macros based on their usage.

Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
10 years agozynq: Add UART0, UART1 configs support
Jagannadha Sutradharudu Teki [Wed, 8 Jan 2014 20:18:08 +0000 (01:48 +0530)]
zynq: Add UART0, UART1 configs support

Zynq uart controller support two serial ports like
CONFIG_ZYNQ_SERIAL_UART0 and CONFIG_ZYNQ_SERIAL_UART1
enabled both so-that the respective board will define
these macros based on their usage.

Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
10 years agozynq: Enable cache options
Jagannadha Sutradharudu Teki [Wed, 8 Jan 2014 20:18:07 +0000 (01:48 +0530)]
zynq: Enable cache options

- Enable cache command
- Turn-off L2 cache
- Turn-on D-cache

Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>