Johannes Berg [Sun, 11 Apr 2021 10:25:42 +0000 (13:25 +0300)]
iwlwifi: fw: print out trigger delay when collecting data
It can be confusing to see "Collecting data: ..." followed by
that not actually happening immediately so print out the delay
in that message.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210411132130.5bd095dc579a.Id1f3b746ac61497951638ba7ce70fc4b63dd87d1@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Johannes Berg [Sun, 11 Apr 2021 10:25:41 +0000 (13:25 +0300)]
iwlwifi: trans/pcie: defer transport initialisation
In a few PCIe devices we may have to swap out the configuration
after we allocate/initialise some parts of the device because
we only know the correct one after reading some registers. This
causes some things such as the byte-count table allocations to
be incorrect, since the configuration is swapped for one with a
bigger queue size.
Fix this by initialising most of the transport much later, only
after the configuration has finally been determined.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210411132130.8f5db97db1e4.Ic622da559b586a04ca536a0ec49ed5ecf03a9354@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Luca Coelho [Sun, 11 Apr 2021 10:25:40 +0000 (13:25 +0300)]
iwlwifi: bump FW API to 63 for AX devices
Start supporting API version 63 for AX devices.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210411132130.a588a9dacd98.Ie4f96b8988c2cbd5f096ee64d0eb0f4829d55aee@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Emmanuel Grumbach [Sun, 11 Apr 2021 10:25:39 +0000 (13:25 +0300)]
iwlwifi: mvm: don't WARN if we can't remove a time event
It is not very useful to WARN if we can't send a host command
The firmware is likely in a bad situation and the fact that
we didn't send the host command has an impact on the firmware
only, not on the driver. The driver could clean up all its
state.
Don't WARN in this case, but just leave a smaller note.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210411132130.0324abc169c8.I4f9b769bc38d68f8ed43f77d2cd75e8f1993e964@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Emmanuel Grumbach [Sun, 11 Apr 2021 10:25:38 +0000 (13:25 +0300)]
iwlwifi: mvm: don't disconnect immediately if we don't hear beacons after CSA
When we switch channel, we may miss a few beacons on the
new channel. Don't disconnect if the time event for the
switch ends before we hear the beacons.
Note that this is relevant only for old devices that still
use the TIME_EVENT firmware API for channel switch.
The check that we hear a beacon before the time event
ends was meant to be used for the association time event
and not for the channel switch time event.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210411132130.3d710091a0bd.I37a161ffdfb099a10080fbdc3b70a4deb76952e2@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Mordechay Goodstein [Sun, 11 Apr 2021 09:46:30 +0000 (12:46 +0300)]
iwlwifi: rs-fw: don't support stbc for HE 160
Our HE doesn't support it so never set HE 160 stbc
Fixes:
3e467b8e4cf4 ("iwlwifi: rs-fw: enable STBC in he correctly")
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210411124418.550fd1903eb7.I8ddbc2f87044a5ef78d916c9c59be797811a1b7f@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Johannes Berg [Sun, 11 Apr 2021 09:46:29 +0000 (12:46 +0300)]
iwlwifi: warn on SKB free w/o op-mode
If this ever happens, and it looks like some code in PCIe is
a bit broken and might lead to this, we want to know without
crashing, so add a WARN_ON_ONCE().
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210411124418.a18b7443dc55.Ia29836738acf14a55af5504aba90c6fea9fff785@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Miri Korenblit [Sun, 11 Apr 2021 09:46:28 +0000 (12:46 +0300)]
iwlwifi: mvm: add support for version 3 of LARI_CONFIG_CHANGE command.
Add support for version 3 of the LARI_CONFIG_CHANGE command.
This is needed to support FW API change which is needed
to support 11ax enablement in Russia.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210411124418.7e68856c8a95.I83acdbe39b63c363cabc04ad42d1d0b9ce98901c@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Mordechay Goodstein [Sun, 11 Apr 2021 09:46:27 +0000 (12:46 +0300)]
iwlwifi: pcie: add ISR debug info for msix debug
The debug prints help in case we get timeout on waiting for
hw.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210411124417.306e2e56d3e8.I72e2977abbb1fddf23b8476bedf6a183fe969ff5@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Mordechay Goodstein [Sun, 11 Apr 2021 09:46:26 +0000 (12:46 +0300)]
iwlwifi: pcie: merge napi_poll_msix functions
The only difference between iwl_pcie_napi_poll_msix_shared() and
iwl_pcie_napi_poll_msix() is when we have a shared queue and nothing
in the rx queue. This case doesn't affect CPU performance, so we can
merge the two functions.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210411124417.9d1b61ef53a5.I60b33d5379cf7c12f1de30fc3fd4cefc38220141@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Johannes Berg [Sun, 11 Apr 2021 09:46:25 +0000 (12:46 +0300)]
iwlwifi: mvm: don't lock mutex in RCU critical section
We cannot lock a mutex while we're in an RCU critical section. At
the same time, we're accessing data structures that are protected
by the mvm->mutex anyway, so just move the entire locking here to
use only that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210411124417.4d27bd36e10e.I1fd8e8fe442c41a5deaa560452b598ed7a60ada5@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Mordechay Goodstein [Sun, 11 Apr 2021 09:46:24 +0000 (12:46 +0300)]
iwlwifi: mvm: remove PS from lower rates.
Power save (PS) should only be enabled when we reach the max phy rate.
Before we reach it (MCS_9) for VHT, we should keep trying to improve the
throughput.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210411124417.2a2fb9f9c25e.I7c7bbcfbdc1d35d2c3338778fb397dd5b08ea0e8@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Roee Goldfiner [Sun, 11 Apr 2021 09:46:23 +0000 (12:46 +0300)]
iwlwifi: mvm: umac error table mismatch
umac_error_table In TLV address was read using mask on MSB
but on the same table in alive message it was without which
caused mismatch in devices with different memory region MSB
Signed-off-by: Roee Goldfiner <roee.h.goldfiner@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210411124417.179fee442115.Ib6eabe86cfda0b6044f07c07448c366b6e07e53d@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Mordechay Goodstein [Sun, 11 Apr 2021 09:46:22 +0000 (12:46 +0300)]
iwlwifi: queue: avoid memory leak in reset flow
In case the device is stopped any usage of hw queues needs to be
reallocated in fw due to fw reset after device stop, so all driver
internal queue should also be freed, and if we don't free the next usage
would leak the old memory and get in recover flows
"iwlwifi 0000:00:03.0: dma_pool_destroy iwlwifi:bc" warning.
Also warn about trying to reuse an internal allocated queue.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210411124417.c72d2f0355c4.Ia3baff633b9b9109f88ab379ef0303aa152c16bf@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Emmanuel Grumbach [Sun, 11 Apr 2021 09:46:21 +0000 (12:46 +0300)]
iwlwifi: don't warn if we can't wait for empty tx queues
If the firmware is dead, the Tx queues won't drain, but
leaving a print in the log is enough, no need to WARN.
If the firmware is dead, we must already have printed enough
information in the log anyway.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210411124417.9a438b2320a9.I4aa897178df82acefd80173d76dd6849ad1bcdc1@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Johannes Berg [Sun, 11 Apr 2021 09:46:20 +0000 (12:46 +0300)]
iwlwifi: remove remaining software checksum code
After the removal of the software checksum code for the
A-MSDU path that we had for testing, the csum_skb variable
stuck around. Remove it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210411124417.280f268ae679.Iad455b6c91e427c9f74963bbd3eb0ce743aaac53@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Emmanuel Grumbach [Sun, 11 Apr 2021 09:46:19 +0000 (12:46 +0300)]
iwlwifi: remove TCM events
Nobody uses that in the user space.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210411124417.b6560a5de0cd.I5dac9c60faed7f48b06d352aa2d65bcf8142c2dc@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Ravi Darsi [Wed, 31 Mar 2021 09:14:52 +0000 (12:14 +0300)]
iwlwifi: mvm: Use IWL_INFO in fw_reset_handshake()
Debug message "firmware didn't ACK the reset - continue anyway\n"
in fw_reset_handshake() is classified as error, however this is not
an error as it is ignored. So, change it to info message for proper
classification of debug messages.
Signed-off-by: Ravi Darsi <ravi.darsi@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210331121101.449b3092c330.I515edcc41913ca7fbe4a4de923671d120d5618c6@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Harish Mitty [Wed, 31 Mar 2021 09:14:51 +0000 (12:14 +0300)]
iwlwifi: mvm: refactor ACPI DSM evaluation function
Instead of implementing the DSM evaluation function in the MVM code,
refactor it so it can be generalized and part of the common ACPI
implementation.
Signed-off-by: Harish Mitty <harish.mitty@intel.com>
[reworded subject and commit message]
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210331121101.a24af3551aac.I8e6bd5eb05f853b6331fa4823750f7ba8ffe46e6@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Miri Korenblit [Wed, 31 Mar 2021 09:14:50 +0000 (12:14 +0300)]
iwlwifi: mvm: support BIOS enable/disable for 11ax in Ukraine
Read the new BIOS DSM and Pass to FW if to disable\enable
11ax for Ukraine according to the BIOS key. this is
needed to enable OEMs to control enable/disable 11ax in Ukraine
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210331121101.055654e7707e.If7eaf9839cd5d59729a235df07e31668b408e740@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Mordechay Goodstein [Wed, 31 Mar 2021 09:14:49 +0000 (12:14 +0300)]
iwlwifi: move iwl_configure_rxq to be used by other op_modes
All the op_modes need to send this command as well. Instead of
duplicating the code from mvm, put the code in a common place.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210331121101.deb71fce883a.I5eef009512f180e5974f3f491ff56c763cdcc878@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
ybaruch [Wed, 31 Mar 2021 09:14:48 +0000 (12:14 +0300)]
iwlwifi: add new so-gf device
add new so-gf device to the driver.
Signed-off-by: ybaruch <yaara.baruch@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210331121101.d6b0c1f85a7e.I2098ca066607edc48336021ea2e5afdbf8196acf@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Miri Korenblit [Wed, 31 Mar 2021 09:14:47 +0000 (12:14 +0300)]
iwlwifi: mvm: enable PPAG in China
Add support for ppag in China by reading revision 2 of the ppag table
from ACPI, and passing the data to the FW.
This is needed to enable OEMs to control ppag enablement
in China.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210331121101.69af388d0dce.I8cfddf9e6837bf394b00390181b4b774ded19acd@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Ilan Peer [Wed, 31 Mar 2021 09:14:46 +0000 (12:14 +0300)]
iwlwifi: mvm: Add support for 6GHz passive scan
When doing scan while 6GHz channels are not enabled, the 6GHz band
is not scanned. Thus, if there are no APs on the 2GHz and 5GHz bands
(that will allow discovery of geographic location etc. that would
allow enabling the 6GHz channels) but there are non collocated APs
on 6GHz PSC channels these would never be discovered.
To overcome this, FW added support for performing passive UHB scan
in case no APs were discovered during scan on the 2GHz and 5GHz
channels.
Add support for enabling such scan when the following conditions are
met:
- 6GHz channels are supported but not enabled by regulatory.
- Station interface is not associated or less than a defined time
interval passed from the last resume or HW reset flows.
- At least 4 channels are included in the scan request
- The scan request includes the widlcard SSID.
- At least 50 minutes passed from the last 6GHz passive scan.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210331121101.7c7bd00e0aeb.Ib226ad57e416b43a710c36a78a617d4243458b99@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
ybaruch [Wed, 31 Mar 2021 09:14:44 +0000 (12:14 +0300)]
iwlwifi: add ax201 killer device
add new killer devices configurations.
Signed-off-by: ybaruch <yaara.baruch@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210331121101.54967363d26d.I5d1a3d810cf6abace51ebb2630d62d891e9fd302@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Avraham Stern [Wed, 31 Mar 2021 09:14:43 +0000 (12:14 +0300)]
iwlwifi: mvm: when associated with PMF, use protected NDP ranging negotiation
When associated to the resonder with PMF, request to protect the NDP
ranging negotiation with PMF.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210331121101.e7982c72e12b.Ib6db362d01a31132c638e194d49476cd8e3ff430@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Johannes Berg [Wed, 31 Mar 2021 09:14:42 +0000 (12:14 +0300)]
iwlwifi: mvm: clean up queue sync implementation
When we do queue sync, it's confusing that we have the structures
declared in the FW API header files that aren't really firmware,
and the union is also confusing - especially now in the code that
checks the size on the return.
So rework this: change the type of sync and whether to do it in a
synchronous fashion to arguments, and build the data structure in
the function, so we don't need the union.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210331121101.f62833fd9893.I612d7ac1c655ec4880329360e15d207698c750bc@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Johannes Berg [Wed, 31 Mar 2021 09:14:41 +0000 (12:14 +0300)]
iwlwifi: mvm: write queue_sync_state only for sync
We use mvm->queue_sync_state to wait for synchronous queue sync
messages, but if an async one happens inbetween we shouldn't
clear mvm->queue_sync_state after sending the async one, that
can run concurrently (at least from the CPU POV) with another
synchronous queue sync.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210331121101.d11c9bcdb4aa.I0772171dbaec87433a11513e9586d98b5d920b5f@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Avraham Stern [Tue, 30 Mar 2021 13:25:00 +0000 (16:25 +0300)]
iwlwifi: mvm: responder: support responder config command version 8
Version 8 add NDP ranging parameters configuration, as well as
enable/disable NDP ranging and LMR feedback.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210330162204.ce9570d755d3.Ic81cb8da9aecbbc9edff468cb4ffbb741418cc73@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Avraham Stern [Tue, 30 Mar 2021 13:24:59 +0000 (16:24 +0300)]
iwlwifi: mvm: support range request command version 12
Version 12 adds configuration of NDP ranging parameters:
- max number of LTF repetitions
- max number of spatial streams
- max total LTFs
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210330162204.2c30c376c5cf.I01460f7277594ee7c98a8e1fe5447c59e70bf073@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Johannes Berg [Tue, 30 Mar 2021 13:24:58 +0000 (16:24 +0300)]
iwlwifi: pcie: make cfg vs. trans_cfg more robust
If we (for example) have a trans_cfg entry in the PCI IDs table,
but then don't find a full cfg entry for it in the info table,
we fall through to the code that treats the PCI ID table entry
as a full cfg entry. This obviously causes crashes later, e.g.
when trying to build the firmware name string.
Avoid such crashes by using the low bit of the pointer as a tag
for trans_cfg entries (automatically using a macro that checks
the type when assigning) and then checking that before trying to
use the data as a full entry - if it's just a partial entry at
that point, fail.
Since we're adding some macro magic, also check that the type is
in fact either struct iwl_cfg_trans_params or struct iwl_cfg,
failing compilation ("initializer element is not constant") if
it isn't.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210330162204.6f69fe6e4128.I921d4ae20ef5276716baeeeda0b001cf25b9b968@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Mordechay Goodstein [Tue, 30 Mar 2021 13:24:57 +0000 (16:24 +0300)]
iwlwifi: pcie: clear only FH bits handle in the interrupt
For simplicity we assume that msix has 2 IRQ lines one used for rx data
called msix_non_share, and another used for one bit flags messages
(alive, hw error, sw error, rx data flag) called msix_share.
Every time the FW has data to send it puts it on the RX queue and HW
turns on the flags in msix_share (inta_fw) indicating about rx data,
and HW sends an interrupt a bit later to the msix_non_share _unless_
the msix_shared RX data bit was cleared.
Currently in the code every time we get an msix_shared we clear all bits
including rx data queue bits.
So we can have a race
----------------------------------------------------
DRIVER | HW | FW
----------------------------------------------------
- send host cmd to FW | |
| | - handle message
| | and put a response
| | on the RX queue
| - RX flag on |
| | - send alive msix
| - alive flag on |
| - interrupt |
| msix_share driver |
- handle msix_shared | |
and clear all flags | |
bits | |
| - don't send an |
| interrupt on |
| msix_non_shared |
| (driver cleared) |
- driver timeout on | |
waiting for host cmd | |
respond | |
| |
----------------------------------------------------
The change is to clear only the msi_shared flags that are handled in
the msix_shared flow, which will cause the hardware to send an interrupt
on the msix_non_share line as well, when it has data.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210330162204.a1cdda2fa270.I02a82312679f4541f30bb8db8747a797dbb70ee7@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
ybaruch [Tue, 30 Mar 2021 13:24:56 +0000 (16:24 +0300)]
iwlwifi: add 160Mhz to killer 1550 name
change the name of 1550 killer device to 160Mhz.
Signed-off-by: ybaruch <yaara.baruch@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210330162204.b87618a26ff8.Icf1d9c150ec108f30ce0e72c18b9350da6ae5087@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
ybaruch [Tue, 30 Mar 2021 13:24:55 +0000 (16:24 +0300)]
iwlwifi: change name to AX 211 and 411 family
change the name of the ax211 and ax411.
Signed-off-by: ybaruch <yaara.baruch@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210330162204.fc3218805052.I203f1a802338f59955bd511c90217f63b918390b@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
ybaruch [Tue, 30 Mar 2021 13:24:54 +0000 (16:24 +0300)]
iwlwifi: change step in so-gf struct
change the step of iwlax210_2ax_cfg_so_jf_a0 to
iwlax210_2ax_cfg_so_jf_b0 as it is on the wcd_fw-dev
repository.
Signed-off-by: ybaruch <yaara.baruch@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210330162204.e9a9d1da76bc.Ie964f37872bbb88d1a02094134f9a2c38faad884@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Matti Gottlieb [Tue, 30 Mar 2021 13:24:53 +0000 (16:24 +0300)]
iwlwifi: pcie: Add support for Bz Family
Add support for different combinations of Bz
and CRFs.
Note: As of now we do not know the exact values
for ltr_delay and xtal_latency, so for now use the
worst case scenario values until the actual values
are clarified.
Signed-off-by: Matti Gottlieb <matti.gottlieb@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210330162204.caac8d996532.I6a22d6decb106cd50d7954b19236b69d685dcc39@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Emmanuel Grumbach [Tue, 30 Mar 2021 13:24:52 +0000 (16:24 +0300)]
iwlwifi: mvm: don't allow CSA if we haven't been fully associated
"Fully associated" means that we heard a beacon with the DTIM
information and the firmware is configured to track the beacons.
Since the firmware needs to track the beacons for the CSA, we
can't configure the firmware for CSA before it knows when the
beacons are expected otherwise we'd get ASSERT 301D.
If we are required to start CSA before we told the firmware
when the beacons are expected to arrive, just report a
failure and let mac80211 disconnect.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210330162204.9adaedeb59e4.Idaad6aaf3f9759d023b8e00b10064915c0db9aa3@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Johannes Berg [Tue, 30 Mar 2021 13:24:51 +0000 (16:24 +0300)]
iwlwifi: pcie: normally grab NIC access for inflight-hcmd
We currently have a special, separate, code path to acquire NIC
access for the in-flight host-command workaround on 7000 series
hardware. However, the normal code path here has grown a number
of additional workarounds/semantics over time, such as reprobing
the device if things fail.
Rather than try to replicate any of this logic, call the normal
grab_nic_access logic for the workaround.
This changes the spinlock to _bh, but that's OK since it's just
redundant, we already have soft-IRQs disabled when we get here,
and so didn't (have to) do it again. Since it's only for commands
there's however no point in making the code more complex just to
not use _bh here.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210330162204.d196fc6ffb23.Idc1ce3ce9fed9178beee7e5409bc669f79b06a0d@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Johannes Berg [Tue, 30 Mar 2021 13:24:50 +0000 (16:24 +0300)]
iwlwifi: pcie: avoid unnecessarily taking spinlock
Most devices don't set the apmg_wake_up_wa flag, so we don't do
anything for them. Avoid taking the spinlock for every command
unless the device needs this workaround.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210330162204.1ab60af3f318.I51cc202f68a2a953223e70c3e8610343412961b6@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Sara Sharon [Tue, 30 Mar 2021 13:24:49 +0000 (16:24 +0300)]
iwlwifi: mvm: enable TX on new CSA channel before disconnecting
When moving to the new channel, we block TX until we hear the
first beacon. if it is not heard, we proceed to disconnect.
Since TX is blocked (without mac80211 being aware of it) the frame
is stuck, resulting with queue hang.
Instead, reenable TX before reporting on the connection loss.
As we are on the new channel, there is no problem with that,
even if the original CSA had quiet mode.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210330162204.eb4f2ff1b863.Ib16238106b33d58b2b7688dc6297018b915ecef4@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Dan Carpenter [Tue, 13 Apr 2021 10:47:59 +0000 (13:47 +0300)]
ionic: return -EFAULT if copy_to_user() fails
The copy_to_user() function returns the number of bytes that it wasn't
able to copy. We want to return -EFAULT to the user.
Fixes:
fee6efce565d ("ionic: add hw timestamp support files")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 13 Apr 2021 22:06:51 +0000 (15:06 -0700)]
Merge branch 'stmmac-xdp-zc'
Ong Boon Leong says:
====================
stmmac: add XDP ZC support
This is the v2 patch series to add XDP ZC support to stmmac driver.
Summary of v2 patch change:-
6/7: fix synchronize_rcu() is called stmmac_disable_all_queues() that is
used by ndo_setup_tc().
########################################################################
Continuous burst traffics are generated by pktgen script and in the midst
of each packet processing operation by xdpsock the following tc-loop.sh
script is looped continuously:-
#!/bin/bash
tc qdisc del dev eth0 parent root
tc qdisc add dev eth0 ingress
tc qdisc add dev eth0 root mqprio num_tc 4 map 0 1 2 3 0 0 0 0 0 0 0 0 0 0 0 0 queues 1@0 1@1 1@2 1@3 hw 0
tc filter add dev eth0 parent ffff: protocol 802.1Q flower vlan_prio 0 hw_tc 0
tc filter add dev eth0 parent ffff: protocol 802.1Q flower vlan_prio 1 hw_tc 1
tc filter add dev eth0 parent ffff: protocol 802.1Q flower vlan_prio 2 hw_tc 2
tc filter add dev eth0 parent ffff: protocol 802.1Q flower vlan_prio 3 hw_tc 3
tc qdisc list dev eth0
tc filter show dev eth0 ingress
On different ssh terminal
$ while true; do ./tc-loop.sh; sleep 1; done
The v2 patch series have been tested using the xdpsock app:
$ ./xdpsock -i eth0 -l -z
From xdpsock poller pps report and dmesg, we don't find any warning
related to rcu and the only difference when the script is executed is
the pps rate drops momentarily.
sock0@eth0:0 l2fwd xdp-drv
pps pkts 1.00
rx 436347
191361334
tx 436411
191361334
sock0@eth0:0 l2fwd xdp-drv
pps pkts 1.00
rx 254117
191615476
tx 254053
191615412
sock0@eth0:0 l2fwd xdp-drv
pps pkts 1.00
rx 466395
192081924
tx 466395
192081860
sock0@eth0:0 l2fwd xdp-drv
pps pkts 1.00
rx 287410
192369365
tx 287474
192369365
sock0@eth0:0 l2fwd xdp-drv
pps pkts 1.00
rx 395853
192765329
tx 395789
192765265
sock0@eth0:0 l2fwd xdp-drv
pps pkts 1.00
rx 466132
193231514
tx 466132
193231450
########################################################################
Based on the above result, the fix looks promising. Appreciate that if
community can help to review the patch series and provide me feedback
for improvement.
====================
Ong Boon Leong [Tue, 13 Apr 2021 09:36:26 +0000 (17:36 +0800)]
net: stmmac: Add TX via XDP zero-copy socket
We add the support of XDP ZC TX submission and cleaning into
stmmac_tx_clean(). The function is made to clean as many TX complete
frames as possible, i.e. limit by priv->dma_tx_size instead of NAPI
budget. For TX ring that is associated with XSK pool, the function
stmmac_xdp_xmit_zc() is introduced to TX frame buffers from XSK pool by
using xsk_tx_peek_desc(). To make stmmac_tx_clean() support the cleaning
of XSK TX frames, STMMAC_TXBUF_T_XSK_TX TX buffer type is introduced.
As stmmac_tx_clean() uses the return value to cue whether NAPI function
should continue to poll, we augment the caller of stmmac_tx_clean() to
pass NAPI budget instead of priv->dma_tx_size through 'budget' input and
made stmmac_tx_clean() to always clean up-to the TX ring size instead.
This allows us to use the return boolean status of stmmac_xdp_xmit_zc()
to decide if XSK TX work is done or not: If true, set 'xmits' to return
'budget - 1' so that NAPI poll may exit. Else, set 'xmits' to return
'budget' to make NAPI poll continue to poll since XSK TX work is not
done. Finally, at the end of stmmac_tx_clean(), the function now take
a maximum value between 'count' and 'xmits' so that status from both
TX cleaning and XSK TX (only for XDP ZC) is considered.
This patch adds a new NAPI poll called stmmac_napi_poll_rxtx() that is
meant to be enabled/disabled for RX and TX ring that are bound to XSK
pool. This NAPI poll function starts with cleaning TX ring, then submits
XSK TX frames to TX ring before proceed to perform RX operations, i.e.
, receiving RX frames and replenishing RX ring with RX free buffers
obtained from XSK pool. Therefore, during XSK RX and TX setup, the driver
enables stmmac_napi_poll_rxtx() for RX and TX operations, then during
XSK RX and TX pool tear-down, the driver reenables the exisiting
independent NAPI poll functions accordingly: stmmac_napi_poll_rx() and
stmmac_napi_poll_tx().
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ong Boon Leong [Tue, 13 Apr 2021 09:36:25 +0000 (17:36 +0800)]
net: stmmac: Enable RX via AF_XDP zero-copy
This patch adds the support for receiving packet via AF_XDP zero-copy
mechanism.
XDP ZC uses 1:1 mapping of XDP buffer to receive packet, therefore the
use of split header is not used currently. The 'xdp_buff' is declared as
union together with a struct that contains 'page', 'addr' and
'page_offset' that are associated with primary buffer.
RX buffers are now allocated either via page_pool or xsk pool. For RX
buffers from xsk_pool they are allocated and deallocated using below
functions:
* stmmac_alloc_rx_buffers_zc(struct stmmac_priv *priv, u32 queue)
* dma_free_rx_xskbufs(struct stmmac_priv *priv, u32 queue)
With above functions now available, we then extend the following driver
functions to support XDP ZC:
* stmmac_reinit_rx_buffers()
* __init_dma_rx_desc_rings()
* init_dma_rx_desc_rings()
* __free_dma_rx_desc_resources()
Note: stmmac_alloc_rx_buffers_zc() may return -ENOMEM due to RX XDP
buffer pool is not allocated (e.g. samples/bpf/xdpsock TX-only). But,
it is still ok to let TX XDP ZC to continue, therefore, the -ENOMEM
is silently ignored to let the driver succcessfully transition to XDP
ZC mode for the said RX and TX queue.
As XDP ZC buffer size is different, the DMA buffer size is required
to be reprogrammed accordingly for RX DMA/Queue that is populated with
XDP buffer from XSK pool.
Next, to add or remove per-queue XSK pool, stmmac_xdp_setup_pool()
will call stmmac_xdp_enable_pool() or stmmac_xdp_disable_pool()
that in-turn coordinates the tearing down and setting up RX ring via
RX buffers and descriptors removal and reallocation through
stmmac_disable_rx_queue() and stmmac_enable_rx_queue(). In addition,
stmmac_xsk_wakeup() is added to initiate XDP RX buffer replenishing
by signalling user application to add available XDP frames back to
FILL queue.
For RX processing using XDP zero-copy buffer, stmmac_rx_zc() is
introduced which is implemented with the assumption that RX split
header is disabled. For XDP verdict is XDP_PASS, the XDP buffer is
copied into a sk_buff allocated through stmmac_construct_skb_zc()
and sent to Linux network GRO inside stmmac_dispatch_skb_zc(). Free RX
buffers are then replenished using stmmac_rx_refill_zc()
v2: introduce __stmmac_disable_all_queues() to contain the original code
that does napi_disable() and then make stmmac_setup_tc_block_cb()
to use it. Move synchronize_rcu() into stmmac_disable_all_queues()
that eventually calls __stmmac_disable_all_queues(). Then,
make both stmmac_release() and stmmac_suspend() to use
stmmac_disable_all_queues(). Thanks David Miller for spotting the
synchronize_rcu() issue in v1 patch.
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ong Boon Leong [Tue, 13 Apr 2021 09:36:24 +0000 (17:36 +0800)]
net: stmmac: Refactor __stmmac_xdp_run_prog for XDP ZC
Prepare stmmac_xdp_run_prog() for AF_XDP zero-copy support which will be
added by upcoming patches by splitting out the XDP verdict processing
into __stmmac_xdp_run_prog() and it callable for XDP ZC path which does
not need to verify bpf_prog is not NULL.
The stmmac_xdp_run_prog() is used for regular XDP Rx path which requires
bpf_prog to be verified.
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ong Boon Leong [Tue, 13 Apr 2021 09:36:23 +0000 (17:36 +0800)]
net: stmmac: rearrange RX and TX desc init into per-queue basis
Below functions are made to be per-queue in preparation of XDP ZC:
__init_dma_rx_desc_rings(struct stmmac_priv *priv, u32 queue, gfp_t flags)
__init_dma_tx_desc_rings(struct stmmac_priv *priv, u32 queue)
The original functions below are stay maintained for all queue usage:
init_dma_rx_desc_rings(struct net_device *dev, gfp_t flags)
init_dma_tx_desc_rings(struct net_device *dev)
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ong Boon Leong [Tue, 13 Apr 2021 09:36:22 +0000 (17:36 +0800)]
net: stmmac: refactor stmmac_init_rx_buffers for stmmac_reinit_rx_buffers
The per-queue RX buffer allocation in stmmac_reinit_rx_buffers() can be
made to use stmmac_alloc_rx_buffers() by merging the page_pool alloc
checks for "buf->page" and "buf->sec_page" in stmmac_init_rx_buffers().
This is in preparation for XSK pool allocation later.
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ong Boon Leong [Tue, 13 Apr 2021 09:36:21 +0000 (17:36 +0800)]
net: stmmac: introduce dma_recycle_rx_skbufs for stmmac_reinit_rx_buffers
Rearrange RX buffer page_pool recycling logics into dma_recycle_rx_skbufs,
so that we prepare stmmac_reinit_rx_buffers() for XSK pool expansion.
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ong Boon Leong [Tue, 13 Apr 2021 09:36:20 +0000 (17:36 +0800)]
net: stmmac: rearrange RX buffer allocation and free functions
This patch restructures the per RX queue buffer allocation from page_pool
to stmmac_alloc_rx_buffers().
We also rearrange dma_free_rx_skbufs() so that it can be used in
init_dma_rx_desc_rings() during freeing of RX buffer in the event of
page_pool allocation failure to replace the more efficient method earlier.
The replacement is needed to make the RX buffer alloc and free method
scalable to XDP ZC xsk_pool alloc and free later.
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 13 Apr 2021 22:02:25 +0000 (15:02 -0700)]
Merge branch 'ipa-SM8350-SoC'
Alex Elder says:
====================
net: ipa: add support for the SM8350 SoC
This small series adds IPA driver support for the Qualcomm SM8350
SoC, which implements IPA v4.9.
The first patch updates the DT binding, and depends on a previous
patch that has already been accepted into net-next.
The second just defines the IPA v4.9 configuration data file.
(Device Tree files to support this SoC will be sent separately and
will go through the Qualcomm tree.)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Alex Elder [Tue, 13 Apr 2021 16:38:26 +0000 (11:38 -0500)]
net: ipa: add IPA v4.9 configuration data
Add support for the SM8350 SoC, which includes IPA version 4.9.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alex Elder [Tue, 13 Apr 2021 16:38:25 +0000 (11:38 -0500)]
dt-bindings: net: qcom,ipa: add support for SM8350
Add support for "qcom,sm8350-ipa", which uses IPA v4.9.
Use "enum" rather than "oneOf/const ..." to specify compatible
strings, as suggested by Rob Herring.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Shannon Nelson [Tue, 13 Apr 2021 17:22:16 +0000 (10:22 -0700)]
ionic: git_ts_info bit shifters
All the uses of HWTSTAMP_FILTER_* values need to be
bit shifters, not straight values.
v2: fixed subject and added Cc Dan and SoB Allen
Fixes:
f8ba81da73fc ("ionic: add ethtool support for PTP")
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: Allen Hubbe <allenbh@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lijun Pan [Tue, 13 Apr 2021 19:33:39 +0000 (14:33 -0500)]
ibmvnic: queue reset work in system_long_wq
The reset process for ibmvnic commonly takes multiple seconds, clearly
making it inappropriate for schedule_work/system_wq. The reason to make
this change is that ibmvnic's use of the default system-wide workqueue
for a relatively long-running work item can negatively affect other
workqueue users. So, queue the relatively slow reset job to the
system_long_wq.
Suggested-by: Nathan Lynch <nathanl@linux.ibm.com>
Signed-off-by: Lijun Pan <lijunp213@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 13 Apr 2021 21:53:11 +0000 (14:53 -0700)]
Merge tag 'linux-can-next-for-5.13-
20210413' of git://git./linux/kernel/git/mkl/linux-can-next
Marc Kleine-Budde says:
====================
pull-request: can-next 2021-04-13
this is a pull request of 14 patches for net-next/master.
The first patch is by Yoshihiro Shimoda and updates the DT bindings
for the rcar_can driver.
Vincent Mailhol contributes 3 patches that add support for several
ETAS USB CAN adapters.
The final 10 patches are by me and clean up the peak_usb CAN driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Yang Li [Tue, 13 Apr 2021 09:46:12 +0000 (17:46 +0800)]
rsi: remove unused including <linux/version.h>
Fix the following versioncheck warning:
./drivers/net/wireless/rsi/rsi_91x_ps.c: 19 linux/version.h not needed.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
wengjianfeng [Tue, 13 Apr 2021 09:45:30 +0000 (17:45 +0800)]
nfc: st-nci: remove unnecessary label
in st_nci_spi_write function, first assign a value to a variable then
goto exit label. return statement just follow the label and exit label
just used once, so we should directly return and remove exit label.
Signed-off-by: wengjianfeng <wengjianfeng@yulong.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lijun Pan [Tue, 13 Apr 2021 08:31:44 +0000 (03:31 -0500)]
ibmvnic: improve failover sysfs entry
The current implementation relies on H_IOCTL call to issue a
H_SESSION_ERR_DETECTED command to let the hypervisor to send a failover
signal. However, it may not work if there is no backup device or if
the vnic is already in error state,
e.g., "ibmvnic
30000003 env3: rx buffer returned with rc 6".
Add a last resort, that is to schedule a failover reset via CRQ command.
Signed-off-by: Lijun Pan <lijunp213@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andreas Roeseler [Mon, 12 Apr 2021 21:23:56 +0000 (16:23 -0500)]
icmp: ICMPV6: pass RFC 8335 reply messages to ping_rcv
The current icmp_rcv function drops all unknown ICMP types, including
ICMP_EXT_ECHOREPLY (type 43). In order to parse Extended Echo Reply messages, we have
to pass these packets to the ping_rcv function, which does not do any
other filtering and passes the packet to the designated socket.
Pass incoming RFC 8335 ICMP Extended Echo Reply packets to the ping_rcv
handler instead of discarding the packet.
Signed-off-by: Andreas Roeseler <andreas.a.roeseler@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 13 Apr 2021 21:35:02 +0000 (14:35 -0700)]
Merge branch 'non-platform-devices-of_get_mac_address'
Michael Walle says:
====================
of: net: support non-platform devices in of_get_mac_address()
of_get_mac_address() is commonly used to fetch the MAC address
from the device tree. It also supports reading it from a NVMEM
provider. But the latter is only possible for platform devices,
because only platform devices are searched for a matching device
node.
Add a second method to fetch the NVMEM cell by a device tree node
instead of a "struct device".
Moreover, the NVMEM subsystem will return dynamically allocated
data which has to be freed after use. Currently, this is handled
by allocating a device resource manged buffer to store the MAC
address. of_get_mac_address() then returns a pointer to this
buffer. Without a device, this trick is not possible anymore.
Thus, change the of_get_mac_address() API to have the caller
supply a buffer.
It was considered to use the network device to attach the buffer
to, but then the order matters and netdev_register() has to be
called before of_get_mac_address(). No driver does it this way.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Walle [Mon, 12 Apr 2021 17:47:18 +0000 (19:47 +0200)]
of: net: fix of_get_mac_addr_nvmem() for non-platform devices
of_get_mac_address() already supports fetching the MAC address by an
nvmem provider. But until now, it was just working for platform devices.
Esp. it was not working for DSA ports and PCI devices. It gets more
common that PCI devices have a device tree binding since SoCs contain
integrated root complexes.
Use the nvmem of_* binding to fetch the nvmem cells by a struct
device_node. We still have to try to read the cell by device first
because there might be a nvmem_cell_lookup associated with that device.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Walle [Mon, 12 Apr 2021 17:47:17 +0000 (19:47 +0200)]
of: net: pass the dst buffer to of_get_mac_address()
of_get_mac_address() returns a "const void*" pointer to a MAC address.
Lately, support to fetch the MAC address by an NVMEM provider was added.
But this will only work with platform devices. It will not work with
PCI devices (e.g. of an integrated root complex) and esp. not with DSA
ports.
There is an of_* variant of the nvmem binding which works without
devices. The returned data of a nvmem_cell_read() has to be freed after
use. On the other hand the return of_get_mac_address() points to some
static data without a lifetime. The trick for now, was to allocate a
device resource managed buffer which is then returned. This will only
work if we have an actual device.
Change it, so that the caller of of_get_mac_address() has to supply a
buffer where the MAC address is written to. Unfortunately, this will
touch all drivers which use the of_get_mac_address().
Usually the code looks like:
const char *addr;
addr = of_get_mac_address(np);
if (!IS_ERR(addr))
ether_addr_copy(ndev->dev_addr, addr);
This can then be simply rewritten as:
of_get_mac_address(np, ndev->dev_addr);
Sometimes is_valid_ether_addr() is used to test the MAC address.
of_get_mac_address() already makes sure, it just returns a valid MAC
address. Thus we can just test its return code. But we have to be
careful if there are still other sources for the MAC address before the
of_get_mac_address(). In this case we have to keep the
is_valid_ether_addr() call.
The following coccinelle patch was used to convert common cases to the
new style. Afterwards, I've manually gone over the drivers and fixed the
return code variable: either used a new one or if one was already
available use that. Mansour Moufid, thanks for that coccinelle patch!
<spml>
@a@
identifier x;
expression y, z;
@@
- x = of_get_mac_address(y);
+ x = of_get_mac_address(y, z);
<...
- ether_addr_copy(z, x);
...>
@@
identifier a.x;
@@
- if (<+... x ...+>) {}
@@
identifier a.x;
@@
if (<+... x ...+>) {
...
}
- else {}
@@
identifier a.x;
expression e;
@@
- if (<+... x ...+>@e)
- {}
- else
+ if (!(e))
{...}
@@
expression x, y, z;
@@
- x = of_get_mac_address(y, z);
+ of_get_mac_address(y, z);
... when != x
</spml>
All drivers, except drivers/net/ethernet/aeroflex/greth.c, were
compile-time tested.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
René van Dorst [Mon, 12 Apr 2021 06:50:31 +0000 (08:50 +0200)]
net: dsa: mt7530: Add support for EEE features
This patch adds EEE support.
Signed-off-by: René van Dorst <opensource@vdorst.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 13 Apr 2021 21:12:34 +0000 (14:12 -0700)]
Merge tag 'wireless-drivers-next-2021-04-13' of git://git./linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for v5.13
First set of patches for v5.13. I have been offline for a couple of
and I have a smaller pull request this time. The next one will be
bigger. Nothing really special standing out.
ath11k
* add initial support for QCN9074, but not enabled yet due to firmware problems
* enable radar detection for 160MHz secondary segment
* handle beacon misses in station mode
rtw88
* 8822c: support firmware crash dump
mt7601u
* enable TDLS support
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Marc Kleine-Budde [Mon, 5 Apr 2021 12:44:15 +0000 (14:44 +0200)]
can: peak_usb: pcan_usb: replace open coded endianness conversion of unaligned data
This patch replaces the open coded endianness conversion of unaligned
data by the appropriate get/put_unaligned_leXX() variants.
Link: https://lore.kernel.org/r/20210406111622.1874957-11-mkl@pengutronix.de
Acked-by: Stephane Grosjean <s.grosjean@peak-system.com>
Tested-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Marc Kleine-Budde [Mon, 5 Apr 2021 17:52:19 +0000 (19:52 +0200)]
can: peak_usb: pcan_usb_get_serial(): unconditionally assign serial_number
The function serial_number is only called from one location with a
valid serial_number pointer. Remove not needed NULL pointer check.
Link: https://lore.kernel.org/r/20210406111622.1874957-10-mkl@pengutronix.de
Acked-by: Stephane Grosjean <s.grosjean@peak-system.com>
Tested-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Marc Kleine-Budde [Mon, 5 Apr 2021 11:49:45 +0000 (13:49 +0200)]
can: peak_usb: pcan_usb_get_serial(): make use of le32_to_cpup()
This patch replaces the memcpy() + le32_to_cpu() by le32_to_cpup().
Link: https://lore.kernel.org/r/20210406111622.1874957-9-mkl@pengutronix.de
Acked-by: Stephane Grosjean <s.grosjean@peak-system.com>
Tested-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Marc Kleine-Budde [Mon, 5 Apr 2021 17:52:19 +0000 (19:52 +0200)]
can: peak_usb: pcan_usb_get_serial(): remove error message from error path
The caller of pcan_usb_get_serial() already prints an error message,
so remove this one and return immediately.
Link: https://lore.kernel.org/r/20210406111622.1874957-8-mkl@pengutronix.de
Acked-by: Stephane Grosjean <s.grosjean@peak-system.com>
Tested-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Marc Kleine-Budde [Mon, 5 Apr 2021 11:49:45 +0000 (13:49 +0200)]
can: peak_usb: pcan_usb_{,pro}_get_device_id(): remove unneeded check for device_id
The callback struct peak_usb_adapter::dev_get_device_id, which is
implemented by the functions pcan_usb_{,pro}_get_device_id() is only
ever called with a valid device_id pointer.
This patch removes the unneeded check if the device_id pointer is
valid.
Link: https://lore.kernel.org/r/20210406111622.1874957-7-mkl@pengutronix.de
Acked-by: Stephane Grosjean <s.grosjean@peak-system.com>
Tested-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Marc Kleine-Budde [Mon, 5 Apr 2021 10:34:56 +0000 (12:34 +0200)]
can: peak_usb: peak_usb_probe(): make use of driver_info
There's no need to iterate over all supported adapters to find the
struct peak_usb_adapter that describes the currently probed devices's
capabilities. The driver core gives us the information for free, if we
assign it to the struct usb_device_id::driver_info.
This patch assigns the usb_device_id::driver_info and converts
peak_usb_probe() to make use of it. This reduces the driver size by
100 bytes on ARCH=arm.
| add/remove: 0/1 grow/shrink: 0/1 up/down: 0/-124 (-124)
| Function old new delta
| peak_usb_adapters_list 24 - -24
| peak_usb_probe 236 136 -100
| Total: Before=25263, After=25139, chg -0.49%
Link: https://lore.kernel.org/r/20210406111622.1874957-6-mkl@pengutronix.de
Acked-by: Stephane Grosjean <s.grosjean@peak-system.com>
Tested-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Marc Kleine-Budde [Sat, 3 Apr 2021 12:10:25 +0000 (14:10 +0200)]
can: peak_usb: remove write only variable struct peak_usb_adapter::ts_period
The variable struct peak_usb_adapter::ts_period is only ever written
to. This patch removes it from the driver.
Link: https://lore.kernel.org/r/20210406111622.1874957-5-mkl@pengutronix.de
Acked-by: Stephane Grosjean <s.grosjean@peak-system.com>
Tested-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Marc Kleine-Budde [Mon, 5 Apr 2021 13:05:28 +0000 (15:05 +0200)]
can: peak_usb: remove unused variables from struct peak_usb_device
This patch removes the unused variables struct
peak_usb_device::echo_skb and struct peak_usb_device::bus_load from
the driver.
Link: https://lore.kernel.org/r/20210406111622.1874957-4-mkl@pengutronix.de
Acked-by: Stephane Grosjean <s.grosjean@peak-system.com>
Tested-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Marc Kleine-Budde [Mon, 5 Apr 2021 19:31:52 +0000 (21:31 +0200)]
can: peak_usb: pcan_usb_pro.h: remove double space in indention
This patch replaces the double space indention after the u8 with a
single space in pcan_usb_pro.h.
Link: https://lore.kernel.org/r/20210406111622.1874957-3-mkl@pengutronix.de
Acked-by: Stephane Grosjean <s.grosjean@peak-system.com>
Tested-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Marc Kleine-Budde [Mon, 5 Apr 2021 10:34:56 +0000 (12:34 +0200)]
can: peak_usb: fix checkpatch warnings
This patch cleans several checkpatch warnings in the peak_usb driver.
Link: https://lore.kernel.org/r/20210406111622.1874957-2-mkl@pengutronix.de
Acked-by: Stephane Grosjean <s.grosjean@peak-system.com>
Tested-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Vincent Mailhol [Sat, 10 Apr 2021 09:59:48 +0000 (18:59 +0900)]
can: etas_es58x: add support for the ETAS ES58X_FD CAN USB interfaces
This patch add support for the ES582.1 and ES584.1 interfaces from
ETAS GmbH (https://www.etas.com/en/products/es58x.php).
Link: https://lore.kernel.org/r/20210410095948.233305-4-mailhol.vincent@wanadoo.fr
Co-developed-by: Arunachalam Santhanam <arunachalam.santhanam@in.bosch.com>
Signed-off-by: Arunachalam Santhanam <arunachalam.santhanam@in.bosch.com>
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Vincent Mailhol [Sat, 10 Apr 2021 09:59:47 +0000 (18:59 +0900)]
can: etas_es58x: add support for ETAS ES581.4 CAN USB interface
This patch adds support for the ES581.4 interface from ETAS
GmbH (https://www.etas.com/en/products/es58x.php).
Link: https://lore.kernel.org/r/20210410095948.233305-3-mailhol.vincent@wanadoo.fr
Co-developed-by: Arunachalam Santhanam <arunachalam.santhanam@in.bosch.com>
Signed-off-by: Arunachalam Santhanam <arunachalam.santhanam@in.bosch.com>
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Vincent Mailhol [Sat, 10 Apr 2021 09:59:46 +0000 (18:59 +0900)]
can: etas_es58x: add core support for ETAS ES58X CAN USB interfaces
This patch adds the core support for various USB CAN interfaces from
ETAS GmbH (https://www.etas.com/en/products/es58x.php). The next
patches add the glue code drivers for the individual interfaces.
Link: https://lore.kernel.org/r/20210410095948.233305-2-mailhol.vincent@wanadoo.fr
Co-developed-by: Arunachalam Santhanam <arunachalam.santhanam@in.bosch.com>
Signed-off-by: Arunachalam Santhanam <arunachalam.santhanam@in.bosch.com>
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Yoshihiro Shimoda [Fri, 9 Apr 2021 00:00:20 +0000 (09:00 +0900)]
dt-bindings: net: can: rcar_can: Document r8a77961 support
Document SoC specific bindings for R-Car M3-W+ (r8a77961) SoC.
Also as R8A7796 is now called R8A77960 so that update those
references.
Link: https://lore.kernel.org/r/20210409000020.2317696-1-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Adam Ford [Mon, 12 Apr 2021 13:26:19 +0000 (08:26 -0500)]
net: ethernet: ravb: Enable optional refclk
For devices that use a programmable clock for the AVB reference clock,
the driver may need to enable them. Add code to find the optional clock
and enable it when available.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adam Ford [Mon, 12 Apr 2021 13:26:18 +0000 (08:26 -0500)]
dt-bindings: net: renesas,etheravb: Add additional clocks
The AVB driver assumes there is an external crystal, but it could
be clocked by other means. In order to enable a programmable
clock, it needs to be added to the clocks list and enabled in the
driver. Since there currently only one clock, there is no
clock-names list either.
Update bindings to add the additional optional clock, and explicitly
name both of them.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 12 Apr 2021 20:34:21 +0000 (13:34 -0700)]
Merge branch 'enetc-ptp'
Yangbo Lu says:
====================
enetc: support PTP Sync packet one-step timestamping
This patch-set is to add support for PTP Sync packet one-step timestamping.
Since ENETC single-step register has to be configured dynamically per
packet for correctionField offeset and UDP checksum update, current
one-step timestamping packet has to be sent only when the last one
completes transmitting on hardware. So, on the TX, this patch handles
one-step timestamping packet as below:
- Trasmit packet immediately if no other one in transfer, or queue to
skb queue if there is already one in transfer.
The test_and_set_bit_lock() is used here to lock and check state.
- Start a work when complete transfer on hardware, to release the bit
lock and to send one skb in skb queue if has.
Changes for v2:
- Rebased.
- Fixed issues from patchwork checks.
- netif_tx_lock for one-step timestamping packet sending.
Changes for v3:
- Used system workqueue.
- Set bit lock when transmitted one-step packet, and scheduled
work when completed. The worker cleared the bit lock, and
transmitted one skb in skb queue if has, instead of a loop.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Yangbo Lu [Mon, 12 Apr 2021 09:03:27 +0000 (17:03 +0800)]
enetc: support PTP Sync packet one-step timestamping
This patch is to add support for PTP Sync packet one-step timestamping.
Since ENETC single-step register has to be configured dynamically per
packet for correctionField offeset and UDP checksum update, current
one-step timestamping packet has to be sent only when the last one
completes transmitting on hardware. So, on the TX, this patch handles
one-step timestamping packet as below:
- Trasmit packet immediately if no other one in transfer, or queue to
skb queue if there is already one in transfer.
The test_and_set_bit_lock() is used here to lock and check state.
- Start a work when complete transfer on hardware, to release the bit
lock and to send one skb in skb queue if has.
And the configuration for one-step timestamping on ENETC before
transmitting is,
- Set one-step timestamping flag in extension BD.
- Write 30 bits current timestamp in tstamp field of extension BD.
- Update PTP Sync packet originTimestamp field with current timestamp.
- Configure single-step register for correctionField offeset and UDP
checksum update.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yangbo Lu [Mon, 12 Apr 2021 09:03:26 +0000 (17:03 +0800)]
enetc: mark TX timestamp type per skb
Mark TX timestamp type per skb on skb->cb[0], instead of
global variable for all skbs. This is a preparation for
one step timestamp support.
For one-step timestamping enablement, there will be both
one-step and two-step PTP messages to transfer. And a skb
queue is needed for one-step PTP messages making sure
start to send current message only after the last one
completed on hardware. (ENETC single-step register has to
be dynamically configured per message.) So, marking TX
timestamp type per skb is required.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 12 Apr 2021 20:31:27 +0000 (13:31 -0700)]
Merge branch 'ibmvnic-errors'
Lijun Pan says:
====================
ibmvnic: improve error printing
Patch 1 prints reset reason as a string.
Patch 2 prints adapter state as a string.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Lijun Pan [Mon, 12 Apr 2021 07:41:28 +0000 (02:41 -0500)]
ibmvnic: print adapter state as a string
The adapter state can be added or deleted over different versions
of the source code. Print a string instead of a number.
Signed-off-by: Lijun Pan <lijunp213@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lijun Pan [Mon, 12 Apr 2021 07:41:27 +0000 (02:41 -0500)]
ibmvnic: print reset reason as a string
The reset reason can be added or deleted over different versions
of the source code. Print a string instead of a number.
Signed-off-by: Lijun Pan <lijunp213@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lijun Pan [Mon, 12 Apr 2021 07:40:59 +0000 (02:40 -0500)]
ibmvnic: clean up the remaining debugfs data structures
Commit
e704f0434ea6 ("ibmvnic: Remove debugfs support") did not
clean up everything. Remove the remaining code.
Signed-off-by: Lijun Pan <lijunp213@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 12 Apr 2021 20:27:11 +0000 (13:27 -0700)]
Merge branch 'netns-sysctl-isolation'
Jonathon Reinhart says:
====================
Ensuring net sysctl isolation
This patchset is the result of an audit of /proc/sys/net to prove that
it is safe to be mouted read-write in a container when a net namespace
is in use. See [1].
The first commit adds code to detect sysctls which are not netns-safe,
and can "leak" changes to other net namespaces.
My manual audit found, and the above feature confirmed, that there are
two nf_conntrack sysctls which are in fact not netns-safe.
I considered sending the latter to netfilter-devel, but I think it's
better to have both together on net-next: Adding only the former causes
undesirable warnings in the kernel log.
[1]: https://github.com/opencontainers/runc/issues/2826
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jonathon Reinhart [Mon, 12 Apr 2021 04:24:53 +0000 (00:24 -0400)]
netfilter: conntrack: Make global sysctls readonly in non-init netns
These sysctls point to global variables:
- NF_SYSCTL_CT_MAX (&nf_conntrack_max)
- NF_SYSCTL_CT_EXPECT_MAX (&nf_ct_expect_max)
- NF_SYSCTL_CT_BUCKETS (&nf_conntrack_htable_size_user)
Because their data pointers are not updated to point to per-netns
structures, they must be marked read-only in a non-init_net ns.
Otherwise, changes in any net namespace are reflected in (leaked into)
all other net namespaces. This problem has existed since the
introduction of net namespaces.
The current logic marks them read-only only if the net namespace is
owned by an unprivileged user (other than init_user_ns).
Commit
d0febd81ae77 ("netfilter: conntrack: re-visit sysctls in
unprivileged namespaces") "exposes all sysctls even if the namespace is
unpriviliged." Since we need to mark them readonly in any case, we can
forego the unprivileged user check altogether.
Fixes:
d0febd81ae77 ("netfilter: conntrack: re-visit sysctls in unprivileged namespaces")
Signed-off-by: Jonathon Reinhart <Jonathon.Reinhart@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jonathon Reinhart [Mon, 12 Apr 2021 04:24:52 +0000 (00:24 -0400)]
net: Ensure net namespace isolation of sysctls
This adds an ensure_safe_net_sysctl() check during register_net_sysctl()
to validate that sysctl table entries for a non-init_net netns are
sufficiently isolated. To be netns-safe, an entry must adhere to at
least (and usually exactly) one of these rules:
1. It is marked read-only inside the netns.
2. Its data pointer does not point to kernel/module global data.
An entry which fails both of these checks is indicative of a bug,
whereby a child netns can affect global net sysctl values.
If such an entry is found, this code will issue a warning to the kernel
log, and force the entry to be read-only to prevent a leak.
To test, simply create a new netns:
$ sudo ip netns add dummy
As it sits now, this patch will WARN for two sysctls which will be
addressed in a subsequent patch:
- /proc/sys/net/netfilter/nf_conntrack_max
- /proc/sys/net/netfilter/nf_conntrack_expect_max
Signed-off-by: Jonathon Reinhart <Jonathon.Reinhart@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
wengjianfeng [Mon, 12 Apr 2021 02:20:06 +0000 (10:20 +0800)]
nfc: pn533: remove redundant assignment
In many places,first assign a value to a variable and then return
the variable. which is redundant, we should directly return the value.
in pn533_rf_field funciton,return rc also in the if statement, so we
use return 0 to replace the last return rc.
Signed-off-by: wengjianfeng <wengjianfeng@yulong.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 12 Apr 2021 20:20:38 +0000 (13:20 -0700)]
Merge branch 'bnxt_en-error-recovery'
Michael Chan says:
====================
bnxt_en: Error recovery fixes.
This series adds some fixes and enhancements to the error recovery
logic. The health register logic is improved and we also add missing
code to free and re-create VF representors in the firmware after
error recovery.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Sriharsha Basavapatna [Mon, 12 Apr 2021 00:18:15 +0000 (20:18 -0400)]
bnxt_en: Free and allocate VF-Reps during error recovery.
During firmware recovery, VF-Rep configuration in the firmware is lost.
Fix it by freeing and (re)allocating VF-Reps in FW at relevant points
during the error recovery process.
Signed-off-by: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Mon, 12 Apr 2021 00:18:14 +0000 (20:18 -0400)]
bnxt_en: Refactor __bnxt_vf_reps_destroy().
Add a new helper function __bnxt_free_one_vf_rep() to free one VF rep.
We also reintialize the VF rep fields to proper initial values so that
the function can be used without freeing the VF rep data structure. This
will be used in subsequent patches to free and recreate VF reps after
error recovery.
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Reviewed-by: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sriharsha Basavapatna [Mon, 12 Apr 2021 00:18:13 +0000 (20:18 -0400)]
bnxt_en: Refactor bnxt_vf_reps_create().
Add a new function bnxt_alloc_vf_rep() to allocate a VF representor.
This function will be needed in subsequent patches to recreate the
VF reps after error recovery.
Signed-off-by: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vasundhara Volam [Mon, 12 Apr 2021 00:18:12 +0000 (20:18 -0400)]
bnxt_en: Invalidate health register mapping at the end of probe.
After probe is successful, interface may not be bought up in all
the cases and health register mapping could be invalid if firmware
undergoes reset. Fix it by invalidating the health register at the
end of probe. It will be remapped during ifup.
Fixes:
43a440c4007b ("bnxt_en: Improve the status_reliable flag in bp->fw_health.")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Mon, 12 Apr 2021 00:18:11 +0000 (20:18 -0400)]
bnxt_en: Treat health register value 0 as valid in bnxt_try_reover_fw().
The retry loop in bnxt_try_recover_fw() should not abort when the
health register value is 0. It is a valid value that indicates the
firmware is booting up.
Fixes:
861aae786f2f ("bnxt_en: Enhance retry of the first message to the firmware.")
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrea Mayer [Sat, 10 Apr 2021 17:46:14 +0000 (19:46 +0200)]
net: seg6: trivial fix of a spelling mistake in comment
There is a comment spelling mistake "interfarence" -> "interference" in
function parse_nla_action(). Fix it.
Signed-off-by: Andrea Mayer <andrea.mayer@uniroma2.it>
Signed-off-by: David S. Miller <davem@davemloft.net>
Colin Ian King [Fri, 9 Apr 2021 16:37:26 +0000 (17:37 +0100)]
net: hns3: Fix potential null pointer defererence of null ae_dev
The reset_prepare and reset_done calls have a null pointer check
on ae_dev however ae_dev is being dereferenced via the call to
ns3_is_phys_func with the ae->pdev argument. Fix this by performing
a null pointer check on ae_dev and hence short-circuiting the
dereference to ae_dev on the call to ns3_is_phys_func.
Addresses-Coverity: ("Dereference before null check")
Fixes:
715c58e94f0d ("net: hns3: add suspend and resume pm_ops")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Colin Ian King [Fri, 9 Apr 2021 13:07:26 +0000 (14:07 +0100)]
net: thunderx: Fix unintentional sign extension issue
The shifting of the u8 integers rq->caching by 26 bits to
the left will be promoted to a 32 bit signed int and then
sign-extended to a u64. In the event that rq->caching is
greater than 0x1f then all then all the upper 32 bits of
the u64 end up as also being set because of the int
sign-extension. Fix this by casting the u8 values to a
u64 before the 26 bit left shift.
Addresses-Coverity: ("Unintended sign extension")
Fixes:
4863dea3fab0 ("net: Adding support for Cavium ThunderX network controller")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>