overlays: Update the upstream overlay

Signed-off-by: Phil Elwell <phil@raspberrypi.com>

overlays: i2c-rtc: Add the Dallas DS1340

See: https://github.com/raspberrypi/linux/issues/4180

Signed-off-by: Phil Elwell <phil@raspberrypi.com>

media: i2c: imx477: Remove unused function parameter

The struct imx477 *ctrl parameter is not used in the function
imx477_adjust_exposure_range(), so remove it.

Signed-off-by: Naushir Patuck <naush@raspberrypi.com>

media: i2c: imx477: Remove internal v4l2_mbus_framefmt from the state

The only field in this struct that is used is the format code, so
replace the struct with this single field.

Save the format code in imx477_set_pad_format() when setting up a new
mode so that imx477_get_pad_format() performs the right lookup.
Otherwise, this caused a bug where the mode lookup occurred on the
12-bit table rather than the 10-bit table.

Signed-off-by: Naushir Patuck <naush@raspberrypi.com>

media: i2c: imx477: Replace existing 1012x760 mode

The existing 1012x760 120 fps mode has significant IQ problem using
the internal sensor scaler. Replace this mode with a 1332x990 120 fps
mode instead. This new mode has a smaller field of view, but does not
suffer from the bad IQ of the original mode.

Signed-off-by: Naushir Patuck <naush@raspberrypi.com>

media: i2c: imx477: Fix crop height for 2028x1080 mode

The crop height for this mode was set at 2600 lines, it should be 2160
lines instead.

Signed-off-by: Naushir Patuck <naush@raspberrypi.com>

configs: Change CONFIG_BLK_DEV_NVME=y for 2711

See https://github.com/raspberrypi/linux/issues/4163

Merge remote-tracking branch 'stable/linux-5.10.y' into rpi-5.10.y

DAC overlays  (#4154)

Adding overlays for PiFi DAC Zero and PiFi DAC HD.

Signed-off-by: David Knell <david.knell@gmail.com>

media: i2c: imx290: Handle exposure correctly when vblank changes

When vblank changes we must modify the exposure range. Also, with this
sensor, the effective exposure time implicitly changes when vblank
does, so we have to reset it after every vblank update.

Signed-off-by: David Plowman <david.plowman@raspberrypi.com>

media: i2c: imx290: Fix up exposure calcuations and ranges

Should now correspond exactly to the datasheet.

Signed-off-by: David Plowman <david.plowman@raspberrypi.com>

media: i2c: imx477: Add very long exposure control to the driver

Add support for very long exposures by using the exposure multiplier
register. Userland does not need to pass any additional controls to
enable long exposures, it simply requests a larger vblank to extend the
exposure control range appropriately.

Currently, since hblank is fixed, a maximum of approximately 124 seconds
of exposure time can be used. In a future change, hblank could also be
controlled in userland to give over 200 seconds of exposure time.

Signed-off-by: Naushir Patuck <naush@raspberrypi.com>

media: i2c: imx477: Remove auto frame length adjusting

The V4L2_CID_EXPOSURE_AUTO_PRIORITY was used to let the sensor control
frame length (effectively framerate) based on the requested exposure
time requested. Remove this feature as it is never used, and goes
against how V4L2 likes to handle exposure and vblank controls.

Signed-off-by: Naushir Patuck <naush@raspberrypi.com>

Linux 5.10.17

Tested-by: Pavel Machek (CIP) <pavel@denx.de>
Tested-by: Jason Self <jason@bluehome.net>
Tested-by: Linux Kernel Functional Testing <lkft@linaro.org>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Shuah Khan <skhan@linuxfoundation.org>
Tested-by: Ross Schmidt <ross.schm.dev@gmail.com>
Link: https://lore.kernel.org/r/20210215152719.459796636@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

kcov, usb: only collect coverage from __usb_hcd_giveback_urb in softirq

commit aee9ddb1d3718d3ba05b50c51622d7792ae749c9 upstream.

Currently there's a KCOV remote coverage collection section in
__usb_hcd_giveback_urb(). Initially that section was added based on the
assumption that usb_hcd_giveback_urb() can only be called in interrupt
context as indicated by a comment before it. This is what happens when
syzkaller is fuzzing the USB stack via the dummy_hcd driver.

As it turns out, it's actually valid to call usb_hcd_giveback_urb() in task
context, provided that the caller turned off the interrupts; USB/IP does
exactly that. This can lead to a nested KCOV remote coverage collection
sections both trying to collect coverage in task context. This isn't
supported by KCOV, and leads to a WARNING.

Change __usb_hcd_giveback_urb() to only call kcov_remote_*() callbacks
when it's being executed in a softirq. As the result, the coverage from
USB/IP related usb_hcd_giveback_urb() calls won't be collected, but the
WARNING is fixed.

A potential future improvement would be to support nested remote coverage
collection sections, but this patch doesn't address that.

Reviewed-by: Dmitry Vyukov <dvyukov@google.com>
Acked-by: Marco Elver <elver@google.com>
Signed-off-by: Andrey Konovalov <andreyknvl@google.com>
Link: https://lore.kernel.org/r/f3a7a153f0719cb53ec385b16e912798bd3e4cf9.1602856358.git.andreyknvl@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ovl: expand warning in ovl_d_real()

commit cef4cbff06fbc3be54d6d79ee139edecc2ee8598 upstream.

There was a syzbot report with this warning but insufficient information...

Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net/qrtr: restrict user-controlled length in qrtr_tun_write_iter()

commit 2a80c15812372e554474b1dba0b1d8e467af295d upstream.

syzbot found WARNING in qrtr_tun_write_iter [1] when write_iter length
exceeds KMALLOC_MAX_SIZE causing order >= MAX_ORDER condition.

Additionally, there is no check for 0 length write.

[1]
WARNING: mm/page_alloc.c:5011
[..]
Call Trace:
 alloc_pages_current+0x18c/0x2a0 mm/mempolicy.c:2267
 alloc_pages include/linux/gfp.h:547 [inline]
 kmalloc_order+0x2e/0xb0 mm/slab_common.c:837
 kmalloc_order_trace+0x14/0x120 mm/slab_common.c:853
 kmalloc include/linux/slab.h:557 [inline]
 kzalloc include/linux/slab.h:682 [inline]
 qrtr_tun_write_iter+0x8a/0x180 net/qrtr/tun.c:83
 call_write_iter include/linux/fs.h:1901 [inline]

Reported-by: syzbot+c2a7e5c5211605a90865@syzkaller.appspotmail.com
Signed-off-by: Sabyrzhan Tasbolatov <snovitoll@gmail.com>
Link: https://lore.kernel.org/r/20210202092059.1361381-1-snovitoll@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net/rds: restrict iovecs length for RDS_CMSG_RDMA_ARGS

commit a11148e6fcce2ae53f47f0a442d098d860b4f7db upstream.

syzbot found WARNING in rds_rdma_extra_size [1] when RDS_CMSG_RDMA_ARGS
control message is passed with user-controlled
0x40001 bytes of args->nr_local, causing order >= MAX_ORDER condition.

The exact value 0x40001 can be checked with UIO_MAXIOV which is 0x400.
So for kcalloc() 0x400 iovecs with sizeof(struct rds_iovec) = 0x10
is the closest limit, with 0x10 leftover.

Same condition is currently done in rds_cmsg_rdma_args().

[1] WARNING: mm/page_alloc.c:5011
[..]
Call Trace:
 alloc_pages_current+0x18c/0x2a0 mm/mempolicy.c:2267
 alloc_pages include/linux/gfp.h:547 [inline]
 kmalloc_order+0x2e/0xb0 mm/slab_common.c:837
 kmalloc_order_trace+0x14/0x120 mm/slab_common.c:853
 kmalloc_array include/linux/slab.h:592 [inline]
 kcalloc include/linux/slab.h:621 [inline]
 rds_rdma_extra_size+0xb2/0x3b0 net/rds/rdma.c:568
 rds_rm_size net/rds/send.c:928 [inline]

Reported-by: syzbot+1bd2b07f93745fa38425@syzkaller.appspotmail.com
Signed-off-by: Sabyrzhan Tasbolatov <snovitoll@gmail.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Link: https://lore.kernel.org/r/20210201203233.1324704-1-snovitoll@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

vsock: fix locking in vsock_shutdown()

commit 1c5fae9c9a092574398a17facc31c533791ef232 upstream.

In vsock_shutdown() we touched some socket fields without holding the
socket lock, such as 'state' and 'sk_flags'.

Also, after the introduction of multi-transport, we are accessing
'vsk->transport' in vsock_send_shutdown() without holding the lock
and this call can be made while the connection is in progress, so
the transport can change in the meantime.

To avoid issues, we hold the socket lock when we enter in
vsock_shutdown() and release it when we leave.

Among the transports that implement the 'shutdown' callback, only
hyperv_transport acquired the lock. Since the caller now holds it,
we no longer take it.

Fixes: d021c344051a ("VSOCK: Introduce VM Sockets")
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

vsock/virtio: update credit only if socket is not closed

commit ce7536bc7398e2ae552d2fabb7e0e371a9f1fe46 upstream.

If the socket is closed or is being released, some resources used by
virtio_transport_space_update() such as 'vsk->trans' may be released.

To avoid a use after free bug we should only update the available credit
when we are sure the socket is still open and we have the lock held.

Fixes: 06a8fc78367d ("VSOCK: Introduce virtio_vsock_common.ko")
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Link: https://lore.kernel.org/r/20210208144454.84438-1-sgarzare@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

switchdev: mrp: Remove SWITCHDEV_ATTR_ID_MRP_PORT_STAT

commit 059d2a1004981dce19f0127dabc1b4ec927d202a upstream.

Now that MRP started to use also SWITCHDEV_ATTR_ID_PORT_STP_STATE to
notify HW, then SWITCHDEV_ATTR_ID_MRP_PORT_STAT is not used anywhere
else, therefore we can remove it.

Fixes: c284b545900830 ("switchdev: mrp: Extend switchdev API to offload MRP")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

bridge: mrp: Fix the usage of br_mrp_port_switchdev_set_state

commit b2bdba1cbc84cadb14393d0101a5bfd38d342e0a upstream.

The function br_mrp_port_switchdev_set_state was called both with MRP
port state and STP port state, which is an issue because they don't
match exactly.

Therefore, update the function to be used only with STP port state and
use the id SWITCHDEV_ATTR_ID_PORT_STP_STATE.

The choice of using STP over MRP is that the drivers already implement
SWITCHDEV_ATTR_ID_PORT_STP_STATE and already in SW we update the port
STP state.

Fixes: 9a9f26e8f7ea30 ("bridge: mrp: Connect MRP API with the switchdev API")
Fixes: fadd409136f0f2 ("bridge: switchdev: mrp: Implement MRP API for switchdev")
Fixes: 2f1a11ae11d222 ("bridge: mrp: Add MRP interface.")
Reported-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: watchdog: hold device global xmit lock during tx disable

commit 3aa6bce9af0e25b735c9c1263739a5639a336ae8 upstream.

Prevent netif_tx_disable() running concurrently with dev_watchdog() by
taking the device global xmit lock. Otherwise, the recommended:

netif_carrier_off(dev);
netif_tx_disable(dev);

driver shutdown sequence can happen after the watchdog has already
checked carrier, resulting in possible false alarms. This is because
netif_tx_lock() only sets the frozen bit without maintaining the locks
on the individual queues.

Fixes: c3f26a269c24 ("netdev: Fix lockdep warnings in multiqueue configurations.")
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net/vmw_vsock: improve locking in vsock_connect_timeout()

commit 3d0bc44d39bca615b72637e340317b7899b7f911 upstream.

A possible locking issue in vsock_connect_timeout() was recognized by
Eric Dumazet which might cause a null pointer dereference in
vsock_transport_cancel_pkt(). This patch assures that
vsock_transport_cancel_pkt() will be called within the lock, so a race
condition won't occur which could result in vsk->transport to be set to NULL.

Fixes: 380feae0def7 ("vsock: cancel packets when failing to connect")
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Norbert Slusarek <nslusarek@gmx.net>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Link: https://lore.kernel.org/r/trinity-f8e0937a-cf0e-4d80-a76e-d9a958ba3ef1-1612535522360@3c-app-gmx-bap12
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net/vmw_vsock: fix NULL pointer dereference

commit 5d1cbcc990f18edaddddef26677073c4e6fad7b7 upstream.

In vsock_stream_connect(), a thread will enter schedule_timeout().
While being scheduled out, another thread can enter vsock_stream_connect()
as well and set vsk->transport to NULL. In case a signal was sent, the
first thread can leave schedule_timeout() and vsock_transport_cancel_pkt()
will be called right after. Inside vsock_transport_cancel_pkt(), a null
dereference will happen on transport->cancel_pkt.

Fixes: c0cfa2d8a788 ("vsock: add multi-transports support")
Signed-off-by: Norbert Slusarek <nslusarek@gmx.net>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Link: https://lore.kernel.org/r/trinity-c2d6cede-bfb1-44e2-85af-1fbc7f541715-1612535117028@3c-app-gmx-bap12
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: fix iteration for sctp transport seq_files

commit af8085f3a4712c57d0dd415ad543bac85780375c upstream.

The sctp transport seq_file iterators take a reference to the transport
in the ->start and ->next functions and releases the reference in the
->show function.  The preferred handling for such resources is to
release them in the subsequent ->next or ->stop function call.

Since Commit 1f4aace60b0e ("fs/seq_file.c: simplify seq_file iteration
code and interface") there is no guarantee that ->show will be called
after ->next, so this function can now leak references.

So move the sctp_transport_put() call to ->next and ->stop.

Fixes: 1f4aace60b0e ("fs/seq_file.c: simplify seq_file iteration code and interface")
Reported-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: gro: do not keep too many GRO packets in napi->rx_list

commit 8dc1c444df193701910f5e80b5d4caaf705a8fb0 upstream.

Commit c80794323e82 ("net: Fix packet reordering caused by GRO and
listified RX cooperation") had the unfortunate effect of adding
latencies in common workloads.

Before the patch, GRO packets were immediately passed to
upper stacks.

After the patch, we can accumulate quite a lot of GRO
packets (depdending on NAPI budget).

My fix is counting in napi->rx_count number of segments
instead of number of logical packets.

Fixes: c80794323e82 ("net: Fix packet reordering caused by GRO and listified RX cooperation")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Bisected-by: John Sperbeck <jsperbeck@google.com>
Tested-by: Jian Yang <jianyang@google.com>
Cc: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Reviewed-by: Edward Cree <ecree.xilinx@gmail.com>
Reviewed-by: Alexander Lobakin <alobakin@pm.me>
Link: https://lore.kernel.org/r/20210204213146.4192368-1-eric.dumazet@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

cpufreq: ACPI: Update arch scale-invariance max perf ratio if CPPC is not there

commit d11a1d08a082a7dc0ada423d2b2e26e9b6f2525c upstream.

If the maximum performance level taken for computing the
arch_max_freq_ratio value used in the x86 scale-invariance code is
higher than the one corresponding to the cpuinfo.max_freq value
coming from the acpi_cpufreq driver, the scale-invariant utilization
falls below 100% even if the CPU runs at cpuinfo.max_freq or slightly
faster, which causes the schedutil governor to select a frequency
below cpuinfo.max_freq.  That frequency corresponds to a frequency
table entry below the maximum performance level necessary to get to
the "boost" range of CPU frequencies which prevents "boost"
frequencies from being used in some workloads.

While this issue is related to scale-invariance, it may be amplified
by commit db865272d9c4 ("cpufreq: Avoid configuring old governors as
default with intel_pstate") from the 5.10 development cycle which
made it extremely easy to default to schedutil even if the preferred
driver is acpi_cpufreq as long as intel_pstate is built too, because
the mere presence of the latter effectively removes the ondemand
governor from the defaults.  Distro kernels are likely to include
both intel_pstate and acpi_cpufreq on x86, so their users who cannot
use intel_pstate or choose to use acpi_cpufreq may easily be
affectecd by this issue.

If CPPC is available, it can be used to address this issue by
extending the frequency tables created by acpi_cpufreq to cover the
entire available frequency range (including "boost" frequencies) for
each CPU, but if CPPC is not there, acpi_cpufreq has no idea what
the maximum "boost" frequency is and the frequency tables created by
it cannot be extended in a meaningful way, so in that case make it
ask the arch scale-invariance code to to use the "nominal" performance
level for CPU utilization scaling in order to avoid the issue at hand.

Fixes: db865272d9c4 ("cpufreq: Avoid configuring old governors as default with intel_pstate")
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Giovanni Gherdovich <ggherdovich@suse.cz>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

cpufreq: ACPI: Extend frequency tables to cover boost frequencies

commit 3c55e94c0adea4a5389c4b80f6ae9927dd6a4501 upstream.

A severe performance regression on AMD EPYC processors when using
the schedutil scaling governor was discovered by Phoronix.com and
attributed to the following commits:

  41ea667227ba ("x86, sched: Calculate frequency invariance for AMD
  systems")

  976df7e5730e ("x86, sched: Use midpoint of max_boost and max_P for
  frequency invariance on AMD EPYC")

The source of the problem is that the maximum performance level taken
for computing the arch_max_freq_ratio value used in the x86 scale-
invariance code is higher than the one corresponding to the
cpuinfo.max_freq value coming from the acpi_cpufreq driver.

This effectively causes the scale-invariant utilization to fall below
100% even if the CPU runs at cpuinfo.max_freq or slightly faster, so
the schedutil governor selects a frequency below cpuinfo.max_freq
then.  That frequency corresponds to a frequency table entry below
the maximum performance level necessary to get to the "boost" range
of CPU frequencies.

However, if the cpuinfo.max_freq value coming from acpi_cpufreq was
higher, the schedutil governor would select higher frequencies which
in turn would allow acpi_cpufreq to set more adequate performance
levels and to get to the "boost" range of CPU frequencies more often.

This issue affects any systems where acpi_cpufreq is used and the
"boost" (or "turbo") frequencies are enabled, not just AMD EPYC.
Moreover, commit db865272d9c4 ("cpufreq: Avoid configuring old
governors as default with intel_pstate") from the 5.10 development
cycle made it extremely easy to default to schedutil even if the
preferred driver is acpi_cpufreq as long as intel_pstate is built
too, because the mere presence of the latter effectively removes the
ondemand governor from the defaults.  Distro kernels are likely to
include both intel_pstate and acpi_cpufreq on x86, so their users
who cannot use intel_pstate or choose to use acpi_cpufreq may
easily be affectecd by this issue.

To address this issue, extend the frequency table constructed by
acpi_cpufreq for each CPU to cover the entire range of available
frequencies (including the "boost" ones) if CPPC is available and
indicates that "boost" (or "turbo") frequencies are enabled.  That
causes cpuinfo.max_freq to become the maximum "boost" frequency of
the given CPU (instead of the maximum frequency returned by the ACPI
_PSS object that corresponds to the "nominal" performance level).

Fixes: 41ea667227ba ("x86, sched: Calculate frequency invariance for AMD systems")
Fixes: 976df7e5730e ("x86, sched: Use midpoint of max_boost and max_P for frequency invariance on AMD EPYC")
Fixes: db865272d9c4 ("cpufreq: Avoid configuring old governors as default with intel_pstate")
Link: https://www.phoronix.com/scan.php?page=article&item=linux511-amd-schedutil&num=1
Link: https://lore.kernel.org/linux-pm/20210203135321.12253-2-ggherdovich@suse.cz/
Reported-by: Michael Larabel <Michael@phoronix.com>
Diagnosed-by: Giovanni Gherdovich <ggherdovich@suse.cz>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Giovanni Gherdovich <ggherdovich@suse.cz>
Reviewed-by: Giovanni Gherdovich <ggherdovich@suse.cz>
Tested-by: Michael Larabel <Michael@phoronix.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: dsa: call teardown method on probe failure

commit 8fd54a73b7cda11548154451bdb4bde6d8ff74c7 upstream.

Since teardown is supposed to undo the effects of the setup method, it
should be called in the error path for dsa_switch_setup, not just in
dsa_switch_teardown.

Fixes: 5e3f847a02aa ("net: dsa: Add teardown callback for drivers")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20210204163351.2929670-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

udp: fix skb_copy_and_csum_datagram with odd segment sizes

commit 52cbd23a119c6ebf40a527e53f3402d2ea38eccb upstream.

When iteratively computing a checksum with csum_block_add, track the
offset "pos" to correctly rotate in csum_block_add when offset is odd.

The open coded implementation of skb_copy_and_csum_datagram did this.
With the switch to __skb_datagram_iter calling csum_and_copy_to_iter,
pos was reinitialized to 0 on each call.

Bring back the pos by passing it along with the csum to the callback.

Changes v1->v2
  - pass csum value, instead of csump pointer (Alexander Duyck)

Link: https://lore.kernel.org/netdev/20210128152353.GB27281@optiplex/
Fixes: 950fcaecd5cc ("datagram: consolidate datagram copy to iter helpers")
Reported-by: Oliver Graute <oliver.graute@gmail.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20210203192952.1849843-1-willemdebruijn.kernel@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

rxrpc: Fix clearance of Tx/Rx ring when releasing a call

commit 7b5eab57cac45e270a0ad624ba157c5b30b3d44d upstream.

At the end of rxrpc_release_call(), rxrpc_cleanup_ring() is called to clear
the Rx/Tx skbuff ring, but this doesn't lock the ring whilst it's accessing
it.  Unfortunately, rxrpc_resend() might be trying to retransmit a packet
concurrently with this - and whilst it does lock the ring, this isn't
protection against rxrpc_cleanup_call().

Fix this by removing the call to rxrpc_cleanup_ring() from
rxrpc_release_call().  rxrpc_cleanup_ring() will be called again anyway
from rxrpc_cleanup_call().  The earlier call is just an optimisation to
recycle skbuffs more quickly.

Alternative solutions include rxrpc_release_call() could try to cancel the
work item or wait for it to complete or rxrpc_cleanup_ring() could lock
when accessing the ring (which would require a bh lock).

This can produce a report like the following:

  BUG: KASAN: use-after-free in rxrpc_send_data_packet+0x19b4/0x1e70 net/rxrpc/output.c:372
  Read of size 4 at addr ffff888011606e04 by task kworker/0:0/5
  ...
  Workqueue: krxrpcd rxrpc_process_call
  Call Trace:
   ...
   kasan_report.cold+0x79/0xd5 mm/kasan/report.c:413
   rxrpc_send_data_packet+0x19b4/0x1e70 net/rxrpc/output.c:372
   rxrpc_resend net/rxrpc/call_event.c:266 [inline]
   rxrpc_process_call+0x1634/0x1f60 net/rxrpc/call_event.c:412
   process_one_work+0x98d/0x15f0 kernel/workqueue.c:2275
   ...

  Allocated by task 2318:
   ...
   sock_alloc_send_pskb+0x793/0x920 net/core/sock.c:2348
   rxrpc_send_data+0xb51/0x2bf0 net/rxrpc/sendmsg.c:358
   rxrpc_do_sendmsg+0xc03/0x1350 net/rxrpc/sendmsg.c:744
   rxrpc_sendmsg+0x420/0x630 net/rxrpc/af_rxrpc.c:560
   ...

  Freed by task 2318:
   ...
   kfree_skb+0x140/0x3f0 net/core/skbuff.c:704
   rxrpc_free_skb+0x11d/0x150 net/rxrpc/skbuff.c:78
   rxrpc_cleanup_ring net/rxrpc/call_object.c:485 [inline]
   rxrpc_release_call+0x5dd/0x860 net/rxrpc/call_object.c:552
   rxrpc_release_calls_on_socket+0x21c/0x300 net/rxrpc/call_object.c:579
   rxrpc_release_sock net/rxrpc/af_rxrpc.c:885 [inline]
   rxrpc_release+0x263/0x5a0 net/rxrpc/af_rxrpc.c:916
   __sock_release+0xcd/0x280 net/socket.c:597
   ...

  The buggy address belongs to the object at ffff888011606dc0
   which belongs to the cache skbuff_head_cache of size 232

Fixes: 248f219cb8bc ("rxrpc: Rewrite the data and ack handling code")
Reported-by: syzbot+174de899852504e4a74a@syzkaller.appspotmail.com
Reported-by: syzbot+3d1c772efafd3c38d007@syzkaller.appspotmail.com
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Hillf Danton <hdanton@sina.com>
Link: https://lore.kernel.org/r/161234207610.653119.5287360098400436976.stgit@warthog.procyon.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

arm64: mte: Allow PTRACE_PEEKMTETAGS access to the zero page

commit 68d54ceeec0e5fee4fb8048e6a04c193f32525ca upstream.

The ptrace(PTRACE_PEEKMTETAGS) implementation checks whether the user
page has valid tags (mapped with PROT_MTE) by testing the PG_mte_tagged
page flag. If this bit is cleared, ptrace(PTRACE_PEEKMTETAGS) returns
-EIO.

A newly created (PROT_MTE) mapping points to the zero page which had its
tags zeroed during cpu_enable_mte(). If there were no prior writes to
this mapping, ptrace(PTRACE_PEEKMTETAGS) fails with -EIO since the zero
page does not have the PG_mte_tagged flag set.

Set PG_mte_tagged on the zero page when its tags are cleared during
boot. In addition, to avoid ptrace(PTRACE_PEEKMTETAGS) succeeding on
!PROT_MTE mappings pointing to the zero page, change the
__access_remote_tags() check to (vm_flags & VM_MTE) instead of
PG_mte_tagged.

Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Fixes: 34bfeea4a9e9 ("arm64: mte: Clear the tags when a page is mapped in user-space with PROT_MTE")
Cc: <stable@vger.kernel.org> # 5.10.x
Cc: Will Deacon <will@kernel.org>
Reported-by: Luis Machado <luis.machado@linaro.org>
Tested-by: Luis Machado <luis.machado@linaro.org>
Reviewed-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Link: https://lore.kernel.org/r/20210210180316.23654-1-catalin.marinas@arm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

x86/pci: Create PCI/MSI irqdomain after x86_init.pci.arch_init()

commit 70245f86c109e0eafb92ea9653184c0e44b4b35c upstream.

Invoking x86_init.irqs.create_pci_msi_domain() before
x86_init.pci.arch_init() breaks XEN PV.

The XEN_PV specific pci.arch_init() function overrides the default
create_pci_msi_domain() which is obviously too late.

As a consequence the XEN PV PCI/MSI allocation goes through the native
path which runs out of vectors and causes malfunction.

Invoke it after x86_init.pci.arch_init().

Fixes: 6b15ffa07dc3 ("x86/irq: Initialize PCI/MSI domain at PCI init time")
Reported-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Juergen Gross <jgross@suse.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/87pn18djte.fsf@nanos.tec.linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

scripts: set proper OpenSSL include dir also for sign-file

commit fe968c41ac4f4ec9ffe3c4cf16b72285f5e9674f upstream.

Fixes: 2cea4a7a1885 ("scripts: use pkg-config to locate libcrypto")
Signed-off-by: Rolf Eike Beer <eb@emlix.com>
Cc: stable@vger.kernel.org # 5.6.x
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

h8300: fix PREEMPTION build, TI_PRE_COUNT undefined

[ Upstream commit ade9679c159d5bbe14fb7e59e97daf6062872e2b ]

Fix a build error for undefined 'TI_PRE_COUNT' by adding it to
asm-offsets.c.

  h8300-linux-ld: arch/h8300/kernel/entry.o: in function `resume_kernel': (.text+0x29a): undefined reference to `TI_PRE_COUNT'

Link: https://lkml.kernel.org/r/20210212021650.22740-1-rdunlap@infradead.org
Fixes: df2078b8daa7 ("h8300: Low level entry")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kernel test robot <lkp@intel.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

i2c: stm32f7: fix configuration of the digital filter

[ Upstream commit 3d6a3d3a2a7a3a60a824e7c04e95fd50dec57812 ]

The digital filter related computation are present in the driver
however the programming of the filter within the IP is missing.
The maximum value for the DNF is wrong and should be 15 instead of 16.

Fixes: aeb068c57214 ("i2c: i2c-stm32f7: add driver")

Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Signed-off-by: Pierre-Yves MORDRET <pierre-yves.mordret@foss.st.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

clk: sunxi-ng: mp: fix parent rate change flag check

[ Upstream commit 245090ab2636c0869527ce563afbfb8aff29e825 ]

CLK_SET_RATE_PARENT flag is checked on parent clock instead of current
one. Fix that.

Fixes: 3f790433c3cb ("clk: sunxi-ng: Adjust MP clock parent rate when allowed")
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Tested-by: Andre Heider <a.heider@gmail.com>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Link: https://lore.kernel.org/r/20210209175900.7092-2-jernej.skrabec@siol.net
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/sun4i: dw-hdmi: Fix max. frequency for H6

[ Upstream commit 1926a0508d8947cf081280d85ff035300dc71da7 ]

It turns out that reasoning for lowering max. supported frequency is
wrong. Scrambling works just fine. Several now fixed bugs prevented
proper functioning, even with rates lower than 340 MHz. Issues were just
more pronounced with higher frequencies.

Fix that by allowing max. supported frequency in HW and fix the comment.

Fixes: cd9063757a22 ("drm/sun4i: DW HDMI: Lower max. supported rate for H6")
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Tested-by: Andre Heider <a.heider@gmail.com>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20210209175900.7092-6-jernej.skrabec@siol.net
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/sun4i: Fix H6 HDMI PHY configuration

[ Upstream commit 6a155216c48f2f65c8dcb02c4c27549c170d24a9 ]

As it turns out, vendor HDMI PHY driver for H6 has a pretty big table
of predefined values for various pixel clocks. However, most of them are
not useful/tested because they come from reference driver code. Vendor
PHY driver is concerned with only few of those, namely 27 MHz, 74.25
MHz, 148.5 MHz, 297 MHz and 594 MHz. These are all frequencies for
standard CEA modes.

Fix sun50i_h6_cur_ctr and sun50i_h6_phy_config with the values only for
aforementioned frequencies.

Table sun50i_h6_mpll_cfg doesn't need to be changed because values are
actually frequency dependent and not so much SoC dependent. See i.MX6
documentation for explanation of those values for similar PHY.

Fixes: c71c9b2fee17 ("drm/sun4i: Add support for Synopsys HDMI PHY")
Tested-by: Andre Heider <a.heider@gmail.com>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20210209175900.7092-5-jernej.skrabec@siol.net
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/sun4i: dw-hdmi: always set clock rate

[ Upstream commit 36b53581fe0dc2e25b67de4e58920307f22d195a ]

As expected, HDMI controller clock should always match pixel clock. In
the past, changing HDMI controller rate would seemingly worsen
situation. However, that was the result of other bugs which are now
fixed.

Fix that by removing set_rate quirk and always set clock rate.

Fixes: 40bb9d3147b2 ("drm/sun4i: Add support for H6 DW HDMI controller")
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Tested-by: Andre Heider <a.heider@gmail.com>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20210209175900.7092-4-jernej.skrabec@siol.net
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/sun4i: tcon: set sync polarity for tcon1 channel

[ Upstream commit 50791f5d7b6a14b388f46c8885f71d1b98216d1d ]

Channel 1 has polarity bits for vsync and hsync signals but driver never
sets them. It turns out that with pre-HDMI2 controllers seemingly there
is no issue if polarity is not set. However, with HDMI2 controllers
(H6) there often comes to de-synchronization due to phase shift. This
causes flickering screen. It's safe to assume that similar issues might
happen also with pre-HDMI2 controllers.

Solve issue with setting vsync and hsync polarity. Note that display
stacks with tcon top have polarity bits actually in tcon0 polarity
register.

Fixes: 9026e0d122ac ("drm: Add Allwinner A10 Display Engine support")
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Tested-by: Andre Heider <a.heider@gmail.com>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20210209175900.7092-3-jernej.skrabec@siol.net
Signed-off-by: Sasha Levin <sashal@kernel.org>

firmware_loader: align .builtin_fw to 8

[ Upstream commit 793f49a87aae24e5bcf92ad98d764153fc936570 ]

arm64 references the start address of .builtin_fw (__start_builtin_fw)
with a pair of R_AARCH64_ADR_PREL_PG_HI21/R_AARCH64_LDST64_ABS_LO12_NC
relocations.  The compiler is allowed to emit the
R_AARCH64_LDST64_ABS_LO12_NC relocation because struct builtin_fw in
include/linux/firmware.h is 8-byte aligned.

The R_AARCH64_LDST64_ABS_LO12_NC relocation requires the address to be a
multiple of 8, which may not be the case if .builtin_fw is empty.
Unconditionally align .builtin_fw to fix the linker error.  32-bit
architectures could use ALIGN(4) but that would add unnecessary
complexity, so just use ALIGN(8).

Link: https://lkml.kernel.org/r/20201208054646.2913063-1-maskray@google.com
Link: https://github.com/ClangBuiltLinux/linux/issues/1204
Fixes: 5658c76 ("firmware: allow firmware files to be built into kernel image")
Signed-off-by: Fangrui Song <maskray@google.com>
Reported-by: kernel test robot <lkp@intel.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Tested-by: Nick Desaulniers <ndesaulniers@google.com>
Tested-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: hns3: add a check for index in hclge_get_rss_key()

[ Upstream commit 532cfc0df1e4d68e74522ef4a0dcbf6ebbe68287 ]

The index is received from vf, if use it directly,
an out-of-bound issue may be caused, so add a check for
this index before using it in hclge_get_rss_key().

Fixes: a638b1d8cc87 ("net: hns3: fix get VF RSS issue")
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: hns3: add a check for tqp_index in hclge_get_ring_chain_from_mbx()

[ Upstream commit 326334aad024a60f46dc5e7dbe1efe32da3ca66f ]

The tqp_index is received from vf, if use it directly,
an out-of-bound issue may be caused, so add a check for
this tqp_index before using it in hclge_get_ring_chain_from_mbx().

Fixes: 84e095d64ed9 ("net: hns3: Change PF to add ring-vect binding & resetQ to mailbox")
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: hns3: add a check for queue_id in hclge_reset_vf_queue()

[ Upstream commit 67a69f84cab60484f02eb8cbc7a76edffbb28a25 ]

The queue_id is received from vf, if use it directly,
an out-of-bound issue may be caused, so add a check for
this queue_id before using it in hclge_reset_vf_queue().

Fixes: 1a426f8b40fc ("net: hns3: fix the VF queue reset flow error")
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: dsa: felix: implement port flushing on .phylink_mac_link_down

[ Upstream commit eb4733d7cffc547e08fe5a216e4f03663bb71108 ]

There are several issues which may be seen when the link goes down while
forwarding traffic, all of which can be attributed to the fact that the
port flushing procedure from the reference manual was not closely
followed.

With flow control enabled on both the ingress port and the egress port,
it may happen when a link goes down that Ethernet packets are in flight.
In flow control mode, frames are held back and not dropped. When there
is enough traffic in flight (example: iperf3 TCP), then the ingress port
might enter congestion and never exit that state. This is a problem,
because it is the egress port's link that went down, and that has caused
the inability of the ingress port to send packets to any other port.
This is solved by flushing the egress port's queues when it goes down.

There is also a problem when performing stream splitting for
IEEE 802.1CB traffic (not yet upstream, but a sort of multicast,
basically). There, if one port from the destination ports mask goes
down, splitting the stream towards the other destinations will no longer
be performed. This can be traced down to this line:

ocelot_port_writel(ocelot_port, 0, DEV_MAC_ENA_CFG);

which should have been instead, as per the reference manual:

ocelot_port_rmwl(ocelot_port, 0, DEV_MAC_ENA_CFG_RX_ENA,
 DEV_MAC_ENA_CFG);

Basically only DEV_MAC_ENA_CFG_RX_ENA should be disabled, but not
DEV_MAC_ENA_CFG_TX_ENA - I don't have further insight into why that is
the case, but apparently multicasting to several ports will cause issues
if at least one of them doesn't have DEV_MAC_ENA_CFG_TX_ENA set.

I am not sure what the state of the Ocelot VSC7514 driver is, but
probably not as bad as Felix/Seville, since VSC7514 uses phylib and has
the following in ocelot_adjust_link:

if (!phydev->link)
return;

therefore the port is not really put down when the link is lost, unlike
the DSA drivers which use .phylink_mac_link_down for that.

Nonetheless, I put ocelot_port_flush() in the common ocelot.c because it
needs to access some registers from drivers/net/ethernet/mscc/ocelot_rew.h
which are not exported in include/soc/mscc/ and a bugfix patch should
probably not move headers around.

Fixes: bdeced75b13f ("net: dsa: felix: Add PCS operations for PHYLINK")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

x86/build: Disable CET instrumentation in the kernel for 32-bit too

[ Upstream commit 256b92af784d5043eeb7d559b6d5963dcc2ecb10 ]

Commit

  20bf2b378729 ("x86/build: Disable CET instrumentation in the kernel")

disabled CET instrumentation which gets added by default by the Ubuntu
gcc9 and 10 by default, but did that only for 64-bit builds. It would
still fail when building a 32-bit target. So disable CET for all x86
builds.

Fixes: 20bf2b378729 ("x86/build: Disable CET instrumentation in the kernel")
Reported-by: AC <achirvasub@gmail.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Josh Poimboeuf <jpoimboe@redhat.com>
Tested-by: AC <achirvasub@gmail.com>
Link: https://lkml.kernel.org/r/YCCIgMHkzh/xT4ex@arch-chirva.localdomain
Signed-off-by: Sasha Levin <sashal@kernel.org>

scsi: scsi_debug: Fix a memory leak

[ Upstream commit f852c596f2ee6f0eb364ea8f28f89da6da0ae7b5 ]

The sdebug_q_arr pointer must be freed when the module is unloaded.

$ cat /sys/kernel/debug/kmemleak
unreferenced object 0xffff888e1cfb0000 (size 4096):
  comm "modprobe", pid 165555, jiffies 4325987516 (age 685.194s)
  hex dump (first 32 bytes):
    00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
    00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
  backtrace:
    [<00000000458f4f5d>] 0xffffffffc06702d9
    [<000000003edc4b1f>] do_one_initcall+0xe9/0x57d
    [<00000000da7d518c>] do_init_module+0x1d1/0x6f0
    [<000000009a6a9248>] load_module+0x36bd/0x4f50
    [<00000000ddb0c3ce>] __do_sys_init_module+0x1db/0x260
    [<000000009532db57>] do_syscall_64+0xa5/0x420
    [<000000002916b13d>] entry_SYSCALL_64_after_hwframe+0x6a/0xdf

Fixes: 87c715dcde63 ("scsi: scsi_debug: Add per_host_store option")
Link: https://lore.kernel.org/r/20210208111734.34034-1-mlombard@redhat.com
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Maurizio Lombardi <mlombard@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

netfilter: conntrack: skip identical origin tuple in same zone only

[ Upstream commit 07998281c268592963e1cd623fe6ab0270b65ae4 ]

The origin skip check needs to re-test the zone. Else, we might skip
a colliding tuple in the reply direction.

This only occurs when using 'directional zones' where origin tuples
reside in different zones but the reply tuples share the same zone.

This causes the new conntrack entry to be dropped at confirmation time
because NAT clash resolution was elided.

Fixes: 4e35c1cb9460240 ("netfilter: nf_nat: skip nat clash resolution for same-origin entries")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ibmvnic: Clear failover_pending if unable to schedule

[ Upstream commit ef66a1eace968ff22a35f45e6e8ec36b668b6116 ]

Normally we clear the failover_pending flag when processing the reset.
But if we are unable to schedule a failover reset we must clear the
flag ourselves. We could fail to schedule the reset if we are in PROBING
state (eg: when booting via kexec) or because we could not allocate memory.

Thanks to Cris Forno for helping isolate the problem and for testing.

Fixes: 1d8504937478 ("powerpc/vnic: Extend "failover pending" window")
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.ibm.com>
Tested-by: Cristobal Forno <cforno12@linux.ibm.com>
Link: https://lore.kernel.org/r/20210203050802.680772-1-sukadev@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: stmmac: set TxQ mode back to DCB after disabling CBS

[ Upstream commit f317e2ea8c88737aa36228167b2292baef3f0430 ]

When disable CBS, mode_to_use parameter is not updated even the operation
mode of Tx Queue is changed to Data Centre Bridging (DCB). Therefore,
when tc_setup_cbs() function is called to re-enable CBS, the operation
mode of Tx Queue remains at DCB, which causing CBS fails to work.

This patch updates the value of mode_to_use parameter to MTL_QUEUE_DCB
after operation mode of Tx Queue is changed to DCB in stmmac_dma_qmode()
callback function.

Fixes: 1f705bc61aee ("net: stmmac: Add support for CBS QDISC")
Suggested-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: Mohammad Athari Bin Ismail <mohammad.athari.ismail@intel.com>
Signed-off-by: Song, Yoong Siang <yoong.siang.song@intel.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Link: https://lore.kernel.org/r/1612447396-20351-1-git-send-email-yoong.siang.song@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

selftests: txtimestamp: fix compilation issue

[ Upstream commit 647b8dd5184665432cc8a2b5bca46a201f690c37 ]

PACKET_TX_TIMESTAMP is defined in if_packet.h but it is not included in
test. Include it instead of <netpacket/packet.h> otherwise the error of
redefinition arrives.
Also fix the compiler warning about ambiguous control flow by adding
explicit braces.

Fixes: 8fe2f761cae9 ("net-timestamp: expand documentation")
Suggested-by: Willem de Bruijn <willemdebruijn.kernel@gmail.com>
Signed-off-by: Vadim Fedorenko <vfedorenko@novek.ru>
Acked-by: Willem de Bruijn <willemb@google.com>
Link: https://lore.kernel.org/r/1612461034-24524-1-git-send-email-vfedorenko@novek.ru
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: enetc: initialize the RFS and RSS memories

[ Upstream commit 07bf34a50e327975b21a9dee64d220c3dcb72ee9 ]

Michael tried to enable Advanced Error Reporting through the ENETC's
Root Complex Event Collector, and the system started spitting out single
bit correctable ECC errors coming from the ENETC interfaces:

pcieport 0000:00:1f.0: AER: Multiple Corrected error received: 0000:00:00.0
fsl_enetc 0000:00:00.0: PCIe Bus Error: severity=Corrected, type=Transaction Layer, (Receiver ID)
fsl_enetc 0000:00:00.0:   device [1957:e100] error status/mask=00004000/00000000
fsl_enetc 0000:00:00.0:    [14] CorrIntErr
fsl_enetc 0000:00:00.1: PCIe Bus Error: severity=Corrected, type=Transaction Layer, (Receiver ID)
fsl_enetc 0000:00:00.1:   device [1957:e100] error status/mask=00004000/00000000
fsl_enetc 0000:00:00.1:    [14] CorrIntErr

Further investigating the port correctable memory error detect register
(PCMEDR) shows that these AER errors have an associated SOURCE_ID of 6
(RFS/RSS):

$ devmem 0x1f8010e10 32
0xC0000006
$ devmem 0x1f8050e10 32
0xC0000006

Discussion with the hardware design engineers reveals that on LS1028A,
the hardware does not do initialization of that RFS/RSS memory, and that
software should clear/initialize the entire table before starting to
operate. That comes as a bit of a surprise, since the driver does not do
initialization of the RFS memory. Also, the initialization of the
Receive Side Scaling is done only partially.

Even though the entire ENETC IP has a single shared flow steering
memory, the flow steering service should returns matches only for TCAM
entries that are within the range of the Station Interface that is doing
the search. Therefore, it should be sufficient for a Station Interface
to initialize all of its own entries in order to avoid any ECC errors,
and only the Station Interfaces in use should need initialization.

There are Physical Station Interfaces associated with PCIe PFs and
Virtual Station Interfaces associated with PCIe VFs. We let the PF
driver initialize the entire port's memory, which includes the RFS
entries which are going to be used by the VF.

Reported-by: Michael Walle <michael@walle.cc>
Fixes: d4fd0404c1c9 ("enetc: Introduce basic PF and VF ENETC ethernet drivers")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Michael Walle <michael@walle.cc>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Link: https://lore.kernel.org/r/20210204134511.2640309-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

hv_netvsc: Reset the RSC count if NVSP_STAT_FAIL in netvsc_receive()

[ Upstream commit 12bc8dfb83b5292fe387b795210018b7632ee08b ]

Commit 44144185951a0f ("hv_netvsc: Add validation for untrusted Hyper-V
values") added validation to rndis_filter_receive_data() (and
rndis_filter_receive()) which introduced NVSP_STAT_FAIL-scenarios where
the count is not updated/reset.  Fix this omission, and prevent similar
scenarios from occurring in the future.

Reported-by: Juan Vazquez <juvazq@microsoft.com>
Signed-off-by: Andrea Parri (Microsoft) <parri.andrea@gmail.com>
Fixes: 44144185951a0f ("hv_netvsc: Add validation for untrusted Hyper-V values")
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Link: https://lore.kernel.org/r/20210203113602.558916-1-parri.andrea@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: ipa: set error code in gsi_channel_setup()

[ Upstream commit 1d23a56b0296d29e7047b41fe0a42a001036160d ]

In gsi_channel_setup(), we check to see if the configuration data
contains any information about channels that are not supported by
the hardware.  If one is found, we abort the setup process, but
the error code (ret) is not set in this case.  Fix this bug.

Fixes: 650d1603825d8 ("soc: qcom: ipa: the generic software interface")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alex Elder <elder@linaro.org>
Link: https://lore.kernel.org/r/20210204010655.15619-1-elder@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: hdlc_x25: Return meaningful error code in x25_open

[ Upstream commit 81b8be68ef8e8915d0cc6cedd2ac425c74a24813 ]

It's not meaningful to pass on LAPB error codes to HDLC code or other
parts of the system, because they will not understand the error codes.

Instead, use system-wide recognizable error codes.

Fixes: f362e5fe0f1f ("wan/hdlc_x25: make lapb params configurable")
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Xie He <xie.he.0141@gmail.com>
Acked-by: Martin Schiller <ms@dev.tdt.de>
Link: https://lore.kernel.org/r/20210203071541.86138-1-xie.he.0141@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

xen/netback: avoid race in xenvif_rx_ring_slots_available()

[ Upstream commit ec7d8e7dd3a59528e305a18e93f1cb98f7faf83b ]

Since commit 23025393dbeb3b8b3 ("xen/netback: use lateeoi irq binding")
xenvif_rx_ring_slots_available() is no longer called only from the rx
queue kernel thread, so it needs to access the rx queue with the
associated queue held.

Reported-by: Igor Druzhinin <igor.druzhinin@citrix.com>
Fixes: 23025393dbeb3b8b3 ("xen/netback: use lateeoi irq binding")
Signed-off-by: Juergen Gross <jgross@suse.com>
Acked-by: Wei Liu <wl@xen.org>
Link: https://lore.kernel.org/r/20210202070938.7863-1-jgross@suse.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

netfilter: flowtable: fix tcp and udp header checksum update

[ Upstream commit 8d6bca156e47d68551750a384b3ff49384c67be3 ]

When updating the tcp or udp header checksum on port nat the function
inet_proto_csum_replace2 with the last parameter pseudohdr as true.
This leads to an error in the case that GRO is used and packets are
split up in GSO. The tcp or udp checksum of all packets is incorrect.

The error is probably masked due to the fact the most network driver
implement tcp/udp checksum offloading. It also only happens when GRO is
applied and not on single packets.

The error is most visible when using a pppoe connection which is not
triggering the tcp/udp checksum offload.

Fixes: ac2a66665e23 ("netfilter: add generic flow table infrastructure")
Signed-off-by: Sven Auhagen <sven.auhagen@voleatech.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

netfilter: nftables: fix possible UAF over chains from packet path in netns

[ Upstream commit 767d1216bff82507c945e92fe719dff2083bb2f4 ]

Although hooks are released via call_rcu(), chain and rule objects are
immediately released while packets are still walking over these bits.

This patch adds the .pre_exit callback which is invoked before
synchronize_rcu() in the netns framework to stay safe.

Remove a comment which is not valid anymore since the core does not use
synchronize_net() anymore since 8c873e219970 ("netfilter: core: free
hooks with call_rcu").

Suggested-by: Florian Westphal <fw@strlen.de>
Fixes: df05ef874b28 ("netfilter: nf_tables: release objects on netns destruction")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

selftests: netfilter: fix current year

[ Upstream commit a3005b0f83f217c888393c6bf9cd36e3d1616bca ]

use date %Y instead of %G to read current year
Problem appeared when running lkp-tests on 01/01/2021

Fixes: 48d072c4e8cd ("selftests: netfilter: add time counter check")
Reported-by: kernel test robot <oliver.sang@intel.com>
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

netfilter: xt_recent: Fix attempt to update deleted entry

[ Upstream commit b1bdde33b72366da20d10770ab7a49fe87b5e190 ]

When both --reap and --update flag are specified, there's a code
path at which the entry to be updated is reaped beforehand,
which then leads to kernel crash. Reap only entries which won't be
updated.

Fixes kernel bugzilla #207773.

Link: https://bugzilla.kernel.org/show_bug.cgi?id=207773
Reported-by: Reindl Harald <h.reindl@thelounge.net>
Fixes: 0079c5aee348 ("netfilter: xt_recent: add an entry reaper")
Signed-off-by: Jozsef Kadlecsik <kadlec@netfilter.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

bpf: Check for integer overflow when using roundup_pow_of_two()

[ Upstream commit 6183f4d3a0a2ad230511987c6c362ca43ec0055f ]

On 32-bit architecture, roundup_pow_of_two() can return 0 when the argument
has upper most bit set due to resulting 1UL << 32. Add a check for this case.

Fixes: d5a3b1f69186 ("bpf: introduce BPF_MAP_TYPE_STACK_TRACE")
Signed-off-by: Bui Quang Minh <minhquangbui99@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20210127063653.3576-1-minhquangbui99@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

bpf: Unbreak BPF_PROG_TYPE_KPROBE when kprobe is called via do_int3

[ Upstream commit 548f1191d86ccb9bde2a5305988877b7584c01eb ]

The commit 0d00449c7a28 ("x86: Replace ist_enter() with nmi_enter()")
converted do_int3 handler to be "NMI-like".
That made old if (in_nmi()) check abort execution of bpf programs
attached to kprobe when kprobe is firing via int3
(For example when kprobe is placed in the middle of the function).
Remove the check to restore user visible behavior.

Fixes: 0d00449c7a28 ("x86: Replace ist_enter() with nmi_enter()")
Reported-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Tested-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: Masami Hiramatsu <mhiramat@kernel.org>
Link: https://lore.kernel.org/bpf/20210203070636.70926-1-alexei.starovoitov@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

dmaengine: idxd: check device state before issue command

[ Upstream commit 89e3becd8f821e507052e012d2559dcda59f538e ]

Add device state check before executing command. Without the check the
command can be issued while device is in halt state and causes the driver to
block while waiting for the completion of the command.

Reported-by: Sanjay Kumar <sanjay.k.kumar@intel.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Tested-by: Sanjay Kumar <sanjay.k.kumar@intel.com>
Fixes: 0d5c10b4c84d ("dmaengine: idxd: add work queue drain support")
Link: https://lore.kernel.org/r/161219313921.2976211.12222625226450097465.stgit@djiang5-desk3.ch.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/vc4: hvs: Fix buffer overflow with the dlist handling

[ Upstream commit facd93f4285c405f9a91b05166147cb39e860666 ]

Commit 0a038c1c29a7 ("drm/vc4: Move LBM creation out of
vc4_plane_mode_set()") changed the LBM allocation logic from first
allocating the LBM memory for the plane to running mode_set,
adding a gap in the LBM, and then running the dlist allocation filling
that gap.

The gap was introduced by incrementing the dlist array index, but was
never checking whether or not we were over the array length, leading
eventually to memory corruptions if we ever crossed this limit.

vc4_dlist_write had that logic though, and was reallocating a larger
dlist array when reaching the end of the buffer. Let's share the logic
between both functions.

Cc: Boris Brezillon <boris.brezillon@collabora.com>
Cc: Eric Anholt <eric@anholt.net>
Fixes: 0a038c1c29a7 ("drm/vc4: Move LBM creation out of vc4_plane_mode_set()")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210129160647.128373-1-maxime@cerno.tech
Signed-off-by: Sasha Levin <sashal@kernel.org>

mt76: dma: fix a possible memory leak in mt76_add_fragment()

[ Upstream commit 93a1d4791c10d443bc67044def7efee2991d48b7 ]

Fix a memory leak in mt76_add_fragment routine returning the buffer
to the page_frag_cache when we receive a new fragment and the
skb_shared_info frag array is full.

Fixes: b102f0c522cf6 ("mt76: fix array overflow on receiving too many fragments for a packet")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Acked-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/4f9dd73407da88b2a552517ce8db242d86bf4d5c.1611616130.git.lorenzo@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>

ath9k: fix build error with LEDS_CLASS=m

[ Upstream commit b64acb28da8394485f0762e657470c9fc33aca4d ]

When CONFIG_ATH9K is built-in but LED support is in a loadable
module, both ath9k drivers fails to link:

x86_64-linux-ld: drivers/net/wireless/ath/ath9k/gpio.o: in function `ath_deinit_leds':
gpio.c:(.text+0x36): undefined reference to `led_classdev_unregister'
x86_64-linux-ld: drivers/net/wireless/ath/ath9k/gpio.o: in function `ath_init_leds':
gpio.c:(.text+0x179): undefined reference to `led_classdev_register_ext'

The problem is that the 'imply' keyword does not enforce any dependency
but is only a weak hint to Kconfig to enable another symbol from a
defconfig file.

Change imply to a 'depends on LEDS_CLASS' that prevents the incorrect
configuration but still allows building the driver without LED support.

The 'select MAC80211_LEDS' is now ensures that the LED support is
actually used if it is present, and the added Kconfig dependency
on MAC80211_LEDS ensures that it cannot be enabled manually when it
has no effect.

Fixes: 197f466e93f5 ("ath9k_htc: Do not select MAC80211_LEDS by default")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210125113654.2408057-1-arnd@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>

dmaengine: idxd: fix misc interrupt completion

[ Upstream commit f5cc9ace24fbdf41b4814effbb2f9bad7046e988 ]

Nikhil reported the misc interrupt handler can sometimes miss handling
the command interrupt when an error interrupt happens near the same time.
Have the irq handling thread continue to process the misc interrupts until
all interrupts are processed. This is a low usage interrupt and is not
expected to handle high volume traffic. Therefore there is no concern of
this thread running for a long time.

Fixes: 0d5c10b4c84d ("dmaengine: idxd: add work queue drain support")
Reported-by: Nikhil Rao <nikhil.rao@intel.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/161074755329.2183844.13295528344116907983.stgit@djiang5-desk3.ch.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

cgroup-v1: add disabled controller check in cgroup1_parse_param()

[ Upstream commit 61e960b07b637f0295308ad91268501d744c21b5 ]

When mounting a cgroup hierarchy with disabled controller in cgroup v1,
all available controllers will be attached.
For example, boot with cgroup_no_v1=cpu or cgroup_disable=cpu, and then
mount with "mount -t cgroup -ocpu cpu /sys/fs/cgroup/cpu", then all
enabled controllers will be attached except cpu.

Fix this by adding disabled controller check in cgroup1_parse_param().
If the specified controller is disabled, just return error with information
"Disabled controller xx" rather than attaching all the other enabled
controllers.

Fixes: f5dfb5315d34 ("cgroup: take options parsing into ->parse_monolithic()")
Signed-off-by: Chen Zhou <chenzhou10@huawei.com>
Reviewed-by: Zefan Li <lizefan.x@bytedance.com>
Reviewed-by: Michal Koutný <mkoutny@suse.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

KVM: x86: cleanup CR3 reserved bits checks

[ Upstream commit c1c35cf78bfab31b8cb455259524395c9e4c7cd6 ]

If not in long mode, the low bits of CR3 are reserved but not enforced to
be zero, so remove those checks.  If in long mode, however, the MBZ bits
extend down to the highest physical address bit of the guest, excluding
the encryption bit.

Make the checks consistent with the above, and match them between
nested_vmcb_checks and KVM_SET_SREGS.

Cc: stable@vger.kernel.org
Fixes: 761e41693465 ("KVM: nSVM: Check that MBZ bits in CR3 and CR4 are not set on vmrun of nested guests")
Fixes: a780a3ea6282 ("KVM: X86: Fix reserved bits check for MOV to CR3")
Reviewed-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

lkdtm: don't move ctors to .rodata

commit 3f618ab3323407ee4c6a6734a37eb6e9663ebfb9 upstream.

When building with KASAN and LKDTM, clang may implictly generate an
asan.module_ctor function in the LKDTM rodata object. The Makefile moves
the lkdtm_rodata_do_nothing() function into .rodata by renaming the
file's .text section to .rodata, and consequently also moves the ctor
function into .rodata, leading to a boot time crash (splat below) when
the ctor is invoked by do_ctors().

Let's prevent this by marking the function as noinstr rather than
notrace, and renaming the file's .noinstr.text to .rodata. Marking the
function as noinstr will prevent tracing and kprobes, and will inhibit
any undesireable compiler instrumentation.

The ctor function (if any) will be placed in .text and will work
correctly.

Example splat before this patch is applied:

[    0.916359] Unable to handle kernel execute from non-executable memory at virtual address ffffa0006b60f5ac
[    0.922088] Mem abort info:
[    0.922828]   ESR = 0x8600000e
[    0.923635]   EC = 0x21: IABT (current EL), IL = 32 bits
[    0.925036]   SET = 0, FnV = 0
[    0.925838]   EA = 0, S1PTW = 0
[    0.926714] swapper pgtable: 4k pages, 48-bit VAs, pgdp=00000000427b3000
[    0.928489] [ffffa0006b60f5ac] pgd=000000023ffff003, p4d=000000023ffff003, pud=000000023fffe003, pmd=0068000042000f01
[    0.931330] Internal error: Oops: 8600000e [#1] PREEMPT SMP
[    0.932806] Modules linked in:
[    0.933617] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 5.10.0-rc7 #2
[    0.935620] Hardware name: linux,dummy-virt (DT)
[    0.936924] pstate: 40400005 (nZcv daif +PAN -UAO -TCO BTYPE=--)
[    0.938609] pc : asan.module_ctor+0x0/0x14
[    0.939759] lr : do_basic_setup+0x4c/0x70
[    0.940889] sp : ffff27b600177e30
[    0.941815] x29: ffff27b600177e30 x28: 0000000000000000
[    0.943306] x27: 0000000000000000 x26: 0000000000000000
[    0.944803] x25: 0000000000000000 x24: 0000000000000000
[    0.946289] x23: 0000000000000001 x22: 0000000000000000
[    0.947777] x21: ffffa0006bf4a890 x20: ffffa0006befb6c0
[    0.949271] x19: ffffa0006bef9358 x18: 0000000000000068
[    0.950756] x17: fffffffffffffff8 x16: 0000000000000000
[    0.952246] x15: 0000000000000000 x14: 0000000000000000
[    0.953734] x13: 00000000838a16d5 x12: 0000000000000001
[    0.955223] x11: ffff94000da74041 x10: dfffa00000000000
[    0.956715] x9 : 0000000000000000 x8 : ffffa0006b60f5ac
[    0.958199] x7 : f9f9f9f9f9f9f9f9 x6 : 000000000000003f
[    0.959683] x5 : 0000000000000040 x4 : 0000000000000000
[    0.961178] x3 : ffffa0006bdc15a0 x2 : 0000000000000005
[    0.962662] x1 : 00000000000000f9 x0 : ffffa0006bef9350
[    0.964155] Call trace:
[    0.964844]  asan.module_ctor+0x0/0x14
[    0.965895]  kernel_init_freeable+0x158/0x198
[    0.967115]  kernel_init+0x14/0x19c
[    0.968104]  ret_from_fork+0x10/0x30
[    0.969110] Code: 00000003 00000000 00000000 00000000 (00000000)
[    0.970815] ---[ end trace b5339784e20d015c ]---

Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Kees Cook <keescook@chromium.org>
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Link: https://lore.kernel.org/r/20201207170533.10738-1-mark.rutland@arm.com
Cc: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

x86/efi: Remove EFI PGD build time checks

[ Upstream commit 816ef8d7a2c4182e19bc06ab65751cb9e3951e94 ]

With CONFIG_X86_5LEVEL, CONFIG_UBSAN and CONFIG_UBSAN_UNSIGNED_OVERFLOW
enabled, clang fails the build with

  x86_64-linux-ld: arch/x86/platform/efi/efi_64.o: in function `efi_sync_low_kernel_mappings':
  efi_64.c:(.text+0x22c): undefined reference to `__compiletime_assert_354'

which happens due to -fsanitize=unsigned-integer-overflow being enabled:

  -fsanitize=unsigned-integer-overflow: Unsigned integer overflow, where
  the result of an unsigned integer computation cannot be represented
  in its type. Unlike signed integer overflow, this is not undefined
  behavior, but it is often unintentional. This sanitizer does not check
  for lossy implicit conversions performed before such a computation
  (see -fsanitize=implicit-conversion).

and that fires when the (intentional) EFI_VA_START/END defines overflow
an unsigned long, leading to the assertion expressions not getting
optimized away (on GCC they do)...

However, those checks are superfluous: the runtime services mapping
code already makes sure the ranges don't overshoot EFI_VA_END as the
EFI mapping range is hardcoded. On each runtime services call, it is
switched to the EFI-specific PGD and even if mappings manage to escape
that last PGD, this won't remain unnoticed for long.

So rip them out.

See https://github.com/ClangBuiltLinux/linux/issues/256 for more info.

Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Tested-by: Nick Desaulniers <ndesaulniers@google.com>
Tested-by: Nathan Chancellor <nathan@kernel.org>
Link: http://lkml.kernel.org/r/20210107223424.4135538-1-arnd@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>

Revert "lib: Restrict cpumask_local_spread to houskeeping CPUs"

[ Upstream commit 2452483d9546de1c540f330469dc4042ff089731 ]

This reverts commit 1abdfe706a579a702799fce465bceb9fb01d407c.

This change is broken and not solving any problem it claims to solve.

Robin reported that cpumask_local_spread() now returns any cpu out of
cpu_possible_mask in case that NOHZ_FULL is disabled (runtime or compile
time). It can also return any offline or not-present CPU in the
housekeeping mask. Before that it was returning a CPU out of
online_cpu_mask.

While the function is racy against CPU hotplug if the caller does not
protect against it, the actual use cases are not caring much about it as
they use it mostly as hint for:

 - the user space affinity hint which is unused by the kernel
 - memory node selection which is just suboptimal
 - network queue affinity which might fail but is handled gracefully

But the occasional fail vs. hotplug is very different from returning
anything from possible_cpu_mask which can have a large amount of offline
CPUs obviously.

The changelog of the commit claims:

 "The current implementation of cpumask_local_spread() does not respect
  the isolated CPUs, i.e., even if a CPU has been isolated for Real-Time
  task, it will return it to the caller for pinning of its IRQ
  threads. Having these unwanted IRQ threads on an isolated CPU adds up
  to a latency overhead."

The only correct part of this changelog is:

 "The current implementation of cpumask_local_spread() does not respect
  the isolated CPUs."

Everything else is just disjunct from reality.

Reported-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Nitesh Narayan Lal <nitesh@redhat.com>
Cc: Marcelo Tosatti <mtosatti@redhat.com>
Cc: abelits@marvell.com
Cc: davem@davemloft.net
Link: https://lore.kernel.org/r/87y2g26tnt.fsf@nanos.tec.linutronix.de
Signed-off-by: Sasha Levin <sashal@kernel.org>

ubsan: implement __ubsan_handle_alignment_assumption

[ Upstream commit 28abcc963149e06d956d95a18a85f4ba26af746f ]

When building ARCH=mips 32r2el_defconfig with CONFIG_UBSAN_ALIGNMENT:

  ld.lld: error: undefined symbol: __ubsan_handle_alignment_assumption
     referenced by slab.h:557 (include/linux/slab.h:557)
                   main.o:(do_initcalls) in archive init/built-in.a
     referenced by slab.h:448 (include/linux/slab.h:448)
                   do_mounts_rd.o:(rd_load_image) in archive init/built-in.a
     referenced by slab.h:448 (include/linux/slab.h:448)
                   do_mounts_rd.o:(identify_ramdisk_image) in archive init/built-in.a
     referenced 1579 more times

Implement this for the kernel based on LLVM's
handleAlignmentAssumptionImpl because the kernel is not linked against
the compiler runtime.

Link: https://github.com/ClangBuiltLinux/linux/issues/1245
Link: https://github.com/llvm/llvm-project/blob/llvmorg-11.0.1/compiler-rt/lib/ubsan/ubsan_handlers.cpp#L151-L190
Link: https://lkml.kernel.org/r/20210127224451.2587372-1-nathan@kernel.org
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Acked-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ARM: kexec: fix oops after TLB are invalidated

[ Upstream commit 4d62e81b60d4025e2dfcd5ea531cc1394ce9226f ]

Giancarlo Ferrari reports the following oops while trying to use kexec:

 Unable to handle kernel paging request at virtual address 80112f38
 pgd = fd7ef03e
 [80112f38] *pgd=0001141e(bad)
 Internal error: Oops: 80d [#1] PREEMPT SMP ARM
 ...

This is caused by machine_kexec() trying to set the kernel text to be
read/write, so it can poke values into the relocation code before
copying it - and an interrupt occuring which changes the page tables.
The subsequent writes then hit read-only sections that trigger a
data abort resulting in the above oops.

Fix this by copying the relocation code, and then writing the variables
into the destination, thereby avoiding the need to make the kernel text
read/write.

Reported-by: Giancarlo Ferrari <giancarlo.ferrari89@gmail.com>
Tested-by: Giancarlo Ferrari <giancarlo.ferrari89@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ARM: ensure the signal page contains defined contents

[ Upstream commit 9c698bff66ab4914bb3d71da7dc6112519bde23e ]

Ensure that the signal page contains our poison instruction to increase
the protection against ROP attacks and also contains well defined
contents.

Acked-by: Will Deacon <will@kernel.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>

kallsyms: fix nonconverging kallsyms table with lld

[ Upstream commit efe6e3068067212b85c2d0474b5ee3b2d0c7adab ]

ARM randconfig builds with lld sometimes show a build failure
from kallsyms:

  Inconsistent kallsyms data
  Try make KALLSYMS_EXTRA_PASS=1 as a workaround

The problem is the veneers/thunks getting added by the linker extend
the symbol table, which in turn leads to more veneers being needed,
so it may take a few extra iterations to converge.

This bug has been fixed multiple times before, but comes back every time
a new symbol name is used. lld uses a different set of identifiers from
ld.bfd, so the additional ones need to be added as well.

I looked through the sources and found that arm64 and mips define similar
prefixes, so I'm adding those as well, aside from the ones I observed. I'm
not sure about powerpc64, which seems to already be handled through a
section match, but if it comes back, the "__long_branch_" and "__plt_"
prefixes would have to get added as well.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ARM: dts: lpc32xx: Revert set default clock rate of HCLK PLL

[ Upstream commit 5638159f6d93b99ec9743ac7f65563fca3cf413d ]

This reverts commit c17e9377aa81664d94b4f2102559fcf2a01ec8e7.

The lpc32xx clock driver is not able to actually change the PLL rate as
this would require reparenting ARM_CLK, DDRAM_CLK, PERIPH_CLK to SYSCLK,
then stop the PLL, update the register, restart the PLL and wait for the
PLL to lock and finally reparent ARM_CLK, DDRAM_CLK, PERIPH_CLK to HCLK
PLL.

Currently, the HCLK driver simply updates the registers but this has no
real effect and all the clock rate calculation end up being wrong. This is
especially annoying for the peripheral (e.g. UARTs, I2C, SPI).

Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Tested-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Link: https://lore.kernel.org/r/20210203090320.GA3760268@piout.net'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

bfq-iosched: Revert "bfq: Fix computation of shallow depth"

[ Upstream commit 388c705b95f23f317fa43e6abf9ff07b583b721a ]

This reverts commit 6d4d273588378c65915acaf7b2ee74e9dd9c130a.

bfq.limit_depth passes word_depths[] as shallow_depth down to sbitmap core
sbitmap_get_shallow, which uses just the number to limit the scan depth of
each bitmap word, formula:
scan_percentage_for_each_word = shallow_depth / (1 << sbimap->shift) * 100%

That means the comments's percentiles 50%, 75%, 18%, 37% of bfq are correct.
But after commit patch 'bfq: Fix computation of shallow depth', we use
sbitmap.depth instead, as a example in following case:

sbitmap.depth = 256, map_nr = 4, shift = 6; sbitmap_word.depth = 64.
The resulsts of computed bfqd->word_depths[] are {128, 192, 48, 96}, and
three of the numbers exceed core dirver's 'sbitmap_word.depth=64' limit
nothing.

Signed-off-by: Lin Feng <linf@wangsu.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>

riscv: virt_addr_valid must check the address belongs to linear mapping

[ Upstream commit 2ab543823322b564f205cb15d0f0302803c87d11 ]

virt_addr_valid macro checks that a virtual address is valid, ie that
the address belongs to the linear mapping and that the corresponding
 physical page exists.

Add the missing check that ensures the virtual address belongs to the
linear mapping, otherwise __virt_to_phys, when compiled with
CONFIG_DEBUG_VIRTUAL enabled, raises a WARN that is interpreted as a
kernel bug by syzbot.

Signed-off-by: Alexandre Ghiti <alex@ghiti.fr>
Reviewed-by: Atish Patra <atish.patra@wdc.com>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/amd/display: Decrement refcount of dc_sink before reassignment

[ Upstream commit 8e92bb0fa75bca9a57e4aba2e36f67d8016a3053 ]

[why]
An old dc_sink state is causing a memory leak because it is missing a
dc_sink_release before a new dc_sink is assigned back to
aconnector->dc_sink.

[how]
Decrement the dc_sink refcount before reassigning it to a new dc_sink.

Signed-off-by: Victor Lu <victorchengchi.lu@amd.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/amd/display: Free atomic state after drm_atomic_commit

[ Upstream commit 2abaa323d744011982b20b8f3886184d56d23946 ]

[why]
drm_atomic_commit was changed so that the caller must free their
drm_atomic_state reference on successes.

[how]
Add drm_atomic_commit_put after drm_atomic_commit call in
dm_force_atomic_commit.

Signed-off-by: Victor Lu <victorchengchi.lu@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/amd/display: Fix dc_sink kref count in emulated_link_detect

[ Upstream commit 3ddc818d9bb877c64f5c649beab97af86c403702 ]

[why]
prev_sink is not used anywhere else in the function and the reference to
it from dc_link is replaced with a new dc_sink.

[how]
Change dc_sink_retain(prev_sink) to dc_sink_release(prev_sink).

Signed-off-by: Victor Lu <victorchengchi.lu@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/amd/display: Release DSC before acquiring

[ Upstream commit 58180a0cc0c57fe62a799a112f95b60f6935bd96 ]

[why]
Need to unassign DSC from pipes that are not using it
so other pipes can acquire it. That is needed for
asic's that have unmatching number of DSC engines from
the number of pipes.

[how]
Before acquiring dsc to stream resources, first remove it.

Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Reviewed-by: Eryk Brol <Eryk.Brol@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/amd/display: Add more Clock Sources to DCN2.1

[ Upstream commit 1622711beebe887e4f0f8237fea1f09bb48e9a51 ]

[WHY]
When enabling HDMI on ComboPHY, there are not
enough clock sources to complete display detection.

[HOW]
Initialize more clock sources.

Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/amd/display: Fix DPCD translation for LTTPR AUX_RD_INTERVAL

[ Upstream commit 2b6b7ab4b1cabfbee1af5d818efcab5d51d62c7e ]

[Why]
The translation between the DPCD value and the specified AUX_RD_INTERVAL
in the DP spec do not match.

[How]
Update values to match the spec.

Signed-off-by: George Shen <george.shen@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

nvme-pci: ignore the subsysem NQN on Phison E16

[ Upstream commit c9e95c39280530200cdd0bbd2670e6334a81970b ]

Tested both with Corsairs firmware 11.3 and 13.0 for the Corsairs MP600
and both have the issue as reported by the kernel.

nvme nvme0: missing or invalid SUBNQN field.

Signed-off-by: Claus Stovgaard <claus.stovgaard@gmail.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

x86/split_lock: Enable the split lock feature on another Alder Lake CPU

[ Upstream commit 8acf417805a5f5c69e9ff66f14cab022c2755161 ]

Add Alder Lake mobile processor to CPU list to enumerate and enable the
split lock feature.

Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Tony Luck <tony.luck@intel.com>
Link: https://lkml.kernel.org/r/20210201190007.4031869-1-fenghua.yu@intel.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

scsi: lpfc: Fix EEH encountering oops with NVMe traffic

[ Upstream commit 8c65830ae1629b03e5d65e9aafae7e2cf5f8b743 ]

In testing, in a configuration with Redfish and native NVMe multipath when
an EEH is injected, a kernel oops is being encountered:

(unreliable)
lpfc_nvme_ls_req+0x328/0x720 [lpfc]
__nvme_fc_send_ls_req.constprop.13+0x1d8/0x3d0 [nvme_fc]
nvme_fc_create_association+0x224/0xd10 [nvme_fc]
nvme_fc_reset_ctrl_work+0x110/0x154 [nvme_fc]
process_one_work+0x304/0x5d

the NBMe transport is issuing a Disconnect LS request, which the driver
receives and tries to post but the work queue used by the driver is already
being torn down by the eeh.

Fix by validating the validity of the work queue before proceeding with the
LS transmit.

Link: https://lore.kernel.org/r/20210127221601.84878-1-jsmart2021@gmail.com
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ovl: skip getxattr of security labels

[ Upstream commit 03fedf93593c82538b18476d8c4f0e8f8435ea70 ]

When inode has no listxattr op of its own (e.g. squashfs) vfs_listxattr
calls the LSM inode_listsecurity hooks to list the xattrs that LSMs will
intercept in inode_getxattr hooks.

When selinux LSM is installed but not initialized, it will list the
security.selinux xattr in inode_listsecurity, but will not intercept it
in inode_getxattr.  This results in -ENODATA for a getxattr call for an
xattr returned by listxattr.

This situation was manifested as overlayfs failure to copy up lower
files from squashfs when selinux is built-in but not initialized,
because ovl_copy_xattr() iterates the lower inode xattrs by
vfs_listxattr() and vfs_getxattr().

ovl_copy_xattr() skips copy up of security labels that are indentified by
inode_copy_up_xattr LSM hooks, but it does that after vfs_getxattr().
Since we are not going to copy them, skip vfs_getxattr() of the security
labels.

Reported-by: Michael Labriola <michael.d.labriola@gmail.com>
Tested-by: Michael Labriola <michael.d.labriola@gmail.com>
Link: https://lore.kernel.org/linux-unionfs/2nv9d47zt7.fsf@aldarion.sourceruckus.org/
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

cap: fix conversions on getxattr

[ Upstream commit f2b00be488730522d0fb7a8a5de663febdcefe0a ]

If a capability is stored on disk in v2 format cap_inode_getsecurity() will
currently return in v2 format unconditionally.

This is wrong: v2 cap should be equivalent to a v3 cap with zero rootid,
and so the same conversions performed on it.

If the rootid cannot be mapped, v3 is returned unconverted.  Fix this so
that both v2 and v3 return -EOVERFLOW if the rootid (or the owner of the fs
user namespace in case of v2) cannot be mapped into the current user
namespace.

Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Acked-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ovl: perform vfs_getxattr() with mounter creds

[ Upstream commit 554677b97257b0b69378bd74e521edb7e94769ff ]

The vfs_getxattr() in ovl_xattr_set() is used to check whether an xattr
exist on a lower layer file that is to be removed.  If the xattr does not
exist, then no need to copy up the file.

This call of vfs_getxattr() wasn't wrapped in credential override, and this
is probably okay.  But for consitency wrap this instance as well.

Reported-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

arm64: dts: rockchip: Disable display for NanoPi R2S

[ Upstream commit 74532de460ec664e5a725507d1b59aa9e4d40776 ]

NanoPi R2S is headless, so rightly does not enable any of the display
interface hardware, which currently provokes an obnoxious error in the
boot log from the fake DRM device failing to find anything to bind to.
It probably isn't *too* hard to obviate the fake device shenanigans
entirely with a bit of driver reshuffling, but for now let's just
disable it here to shut up the spurious error.

Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Link: https://lore.kernel.org/r/c4553dfad1ad6792c4f22454c135ff55de77e2d6.1611186099.git.robin.murphy@arm.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

platform/x86: hp-wmi: Disable tablet-mode reporting by default

[ Upstream commit 67fbe02a5cebc3c653610f12e3c0424e58450153 ]

Recently userspace has started making more use of SW_TABLET_MODE
(when an input-dev reports this).

Specifically recent GNOME3 versions will:

1.  When SW_TABLET_MODE is reported and is reporting 0:
1.1 Disable accelerometer-based screen auto-rotation
1.2 Disable automatically showing the on-screen keyboard when a
    text-input field is focussed

2.  When SW_TABLET_MODE is reported and is reporting 1:
2.1 Ignore input-events from the builtin keyboard and touchpad
    (this is for 360° hinges style 2-in-1s where the keyboard and
     touchpads are accessible on the back of the tablet when folded
     into tablet-mode)

This means that claiming to support SW_TABLET_MODE when it does not
actually work / reports correct values has bad side-effects.

The check in the hp-wmi code which is used to decide if the input-dev
should claim SW_TABLET_MODE support, only checks if the
HPWMI_HARDWARE_QUERY is supported. It does *not* check if the hardware
actually is capable of reporting SW_TABLET_MODE.

This leads to the hp-wmi input-dev claiming SW_TABLET_MODE support,
while in reality it will always report 0 as SW_TABLET_MODE value.
This has been seen on a "HP ENVY x360 Convertible 15-cp0xxx" and
this likely is the case on a whole lot of other HP models.

This problem causes both auto-rotation and on-screen keyboard
support to not work on affected x360 models.

There is no easy fix for this, but since userspace expects
SW_TABLET_MODE reporting to be reliable when advertised it is
better to not claim/report SW_TABLET_MODE support at all, then
to claim to support it while it does not work.

To avoid the mentioned problems, add a new enable_tablet_mode_sw
module-parameter which defaults to false.

Note I've made this an int using the standard -1=auto, 0=off, 1=on
triplett, with the hope that in the future we can come up with a
better way to detect SW_TABLET_MODE support. ATM the default
auto option just does the same as off.

BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1918255
Cc: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mark Gross <mgross@linux.intel.com>
Link: https://lore.kernel.org/r/20210120124941.73409-1-hdegoede@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

arm64: dts: rockchip: remove interrupt-names property from rk3399 vdec node

[ Upstream commit 94a5400f8b966c91c49991bae41c2ef911b935ac ]

A test with the command below gives this error:
/arch/arm64/boot/dts/rockchip/rk3399-evb.dt.yaml: video-codec@ff660000:
'interrupt-names' does not match any of the regexes: 'pinctrl-[0-9]+'

The rkvdec driver gets it irq with help of the platform_get_irq()
function, so remove the interrupt-names property from the rk3399
vdec node.

make ARCH=arm64 dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/
media/rockchip,vdec.yaml

Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20210117181653.24886-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ARM: OMAP2+: Fix suspcious RCU usage splats for omap_enter_idle_coupled

[ Upstream commit 06862d789ddde8a99c1e579e934ca17c15a84755 ]

We get suspcious RCU usage splats with cpuidle in several places in
omap_enter_idle_coupled() with the kernel debug options enabled:

RCU used illegally from extended quiescent state!
...
(_raw_spin_lock_irqsave)
(omap_enter_idle_coupled+0x17c/0x2d8)
(omap_enter_idle_coupled)
(cpuidle_enter_state)
(cpuidle_enter_state_coupled)
(cpuidle_enter)

Let's use RCU_NONIDLE to suppress these splats. Things got changed around
with commit 1098582a0f6c ("sched,idle,rcu: Push rcu_idle deeper into the
idle path") that started triggering these warnings.

For the tick_broadcast related calls, ideally we'd just switch over to
using CPUIDLE_FLAG_TIMER_STOP for omap_enter_idle_coupled() to have the
generic cpuidle code handle the tick_broadcast related calls for us and
then just drop the tick_broadcast calls here.

But we're currently missing the call in the common cpuidle code for
tick_broadcast_enable() that CPU1 hotplug needs as described in earlier
commit 50d6b3cf9403 ("ARM: OMAP2+: fix lack of timer interrupts on CPU1
after hotplug").

Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Paul E. McKenney <paulmck@kernel.org>
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Acked-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

arm64: dts: qcom: sdm845: Reserve LPASS clocks in gcc

[ Upstream commit 93f2a11580a9732c1d90f9e01a7e9facc825658f ]

The GCC_LPASS_Q6_AXI_CLK and GCC_LPASS_SWAY_CLK clocks may not be
touched on a typical UEFI based SDM845 device, but when the kernel is
built with CONFIG_SDM_LPASSCC_845 this happens, unless they are marked
as protected-clocks in the DT.

This was done for the MTP and the Pocophone, but not for DB845c and the
Lenovo Yoga C630 - causing these to fail to boot if the LPASS clock
controller is enabled (which it typically isn't).

Tested-by: Vinod Koul <vkoul@kernel.org> #on db845c
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20201222001103.3112306-1-bjorn.andersson@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

arm64: dts: rockchip: Fix PCIe DT properties on rk3399

[ Upstream commit 43f20b1c6140896916f4e91aacc166830a7ba849 ]

It recently became apparent that the lack of a 'device_type = "pci"'
in the PCIe root complex node for rk3399 is a violation of the PCI
binding, as documented in IEEE Std 1275-1994. Changes to the kernel's
parsing of the DT made such violation fatal, as drivers cannot
probe the controller anymore.

Add the missing property makes the PCIe node compliant. While we
are at it, drop the pointless linux,pci-domain property, which only
makes sense when there are multiple host bridges.

Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200815125112.462652-3-maz@kernel.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

soc: ti: omap-prm: Fix boot time errors for rst_map_012 bits 0 and 1

[ Upstream commit 7078a5ba7a58e5db07583b176f8a03e0b8714731 ]

We have rst_map_012 used for various accelerators like dsp, ipu and iva.
For these use cases, we have rstctrl bit 2 control the subsystem module
reset, and have and bits 0 and 1 control the accelerator specific
features.

If the bootloader, or kexec boot, has left any accelerator specific
reset bits deasserted, deasserting bit 2 reset will potentially enable
an accelerator with unconfigured MMU and no firmware. And we may get
spammed with a lot by warnings on boot with "Data Access in User mode
during Functional access", or depending on the accelerator, the system
can also just hang.

This issue can be quite easily reproduced by setting a rst_map_012 type
rstctrl register to 0 or 4 in the bootloader, and booting the system.

Let's just assert all reset bits for rst_map_012 type resets. So far
it looks like the other rstctrl types don't need this. If it turns out
that the other type rstctrl bits also need reset on init, we need to
add an instance specific reset mask for the bits to avoid resetting
unwanted bits.

Reported-by: Carl Philipp Klemm <philipp@uvos.xyz>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Santosh Shilimkar <ssantosh@kernel.org>
Cc: Suman Anna <s-anna@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Tested-by: Carl Philipp Klemm <philipp@uvos.xyz>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>