review.tizen.org Git - platform/kernel/linux-starfive.git/log

Merge branches 'clk-imx', 'clk-samsung', 'clk-annotate', 'clk-marvell' and 'clk-lmk' into clk-next

- Add __counted_by to struct clk_hw_onecell_data and struct spmi_pmic_div_clk_cc
- Remove non-OF mmp clk drivers
- Move number of clks from DT headers to drivers

* clk-imx:
  clk: imx: pll14xx: dynamically configure PLL for 393216000/361267200Hz
  clk: imx: pll14xx: align pdiv with reference manual
  clk: imx: composite-8m: fix clock pauses when set_rate would be a no-op
  clk: imx25: make __mx25_clocks_init return void
  clk: imx25: print silicon revision during init
  dt-bindings: clocks: imx8mp: make sai4 a dummy clock
  clk: imx8mp: fix sai4 clock
  clk: imx: imx8ulp: update SPLL2 type
  clk: imx: pllv4: Fix SPLL2 MULT range
  clk: imx: imx8: add audio clock mux driver
  dt-bindings: clock: fsl,imx8-acm: Add audio clock mux support
  clk: imx: clk-imx8qxp-lpcg: Convert to devm_platform_ioremap_resource()
  clk: imx: clk-gpr-mux: Simplify .determine_rate()
  clk: imx: Add 519.75MHz frequency support for imx9 pll
  clk: imx93: Add PDM IPG clk
  dt-bindings: clock: imx93: Add PDM IPG clk

* clk-samsung:
  dt-bindings: clock: samsung: remove define with number of clocks
  clk: samsung: exynoautov9: do not define number of clocks in bindings
  clk: samsung: exynos850: do not define number of clocks in bindings
  clk: samsung: exynos7885: do not define number of clocks in bindings
  clk: samsung: exynos5433: do not define number of clocks in bindings
  clk: samsung: exynos5420: do not define number of clocks in bindings
  clk: samsung: exynos5410: do not define number of clocks in bindings
  clk: samsung: exynos5260: do not define number of clocks in bindings
  clk: samsung: exynos5250: do not define number of clocks in bindings
  clk: samsung: exynos4: do not define number of clocks in bindings
  clk: samsung: exynos3250: do not define number of clocks in bindings

* clk-annotate:
  clk: qcom: clk-spmi-pmic-div: Annotate struct spmi_pmic_div_clk_cc with __counted_by
  clk: Annotate struct clk_hw_onecell_data with __counted_by

* clk-marvell:
  clk: pxa910: Move number of clocks to driver source
  clk: pxa1928: Move number of clocks to driver source
  clk: pxa168: Move number of clocks to driver source
  clk: mmp2: Move number of clocks to driver source
  clk: mmp: Remove old non-OF clock drivers

* clk-lmk:
  clk: lmk04832: Support using PLL1_LD as SPI readback pin
  clk: lmk04832: Don't disable vco clock on probe fail
  clk: lmk04832: Set missing parent_names for output clocks

Merge branches 'clk-versa', 'clk-strdup', 'clk-amlogic', 'clk-allwinner' and 'clk-rockchip' into clk-next

- Add Versa3 clk generator to support 48KHz playback/record with audio
   codec on RZ/G2L SMARC EVK
- Introduce kstrdup_and_replace() and use it

* clk-versa:
  clk: vc7: Use i2c_get_match_data() instead of device_get_match_data()
  clk: vc5: Use i2c_get_match_data() instead of device_get_match_data()
  clk: versaclock3: Switch to use i2c_driver's probe callback
  clk: Add support for versa3 clock driver
  dt-bindings: clock: Add Renesas versa3 clock generator bindings

* clk-strdup:
  clk: ti: Replace kstrdup() + strreplace() with kstrdup_and_replace()
  clk: tegra: Replace kstrdup() + strreplace() with kstrdup_and_replace()
  driver core: Replace kstrdup() + strreplace() with kstrdup_and_replace()
  lib/string_helpers: Add kstrdup_and_replace() helper

* clk-amlogic: (22 commits)
  dt-bindings: soc: amlogic: document System Control registers
  dt-bindings: clock: amlogic: convert amlogic,gxbb-aoclkc.txt to dt-schema
  dt-bindings: clock: amlogic: convert amlogic,gxbb-clkc.txt to dt-schema
  clk: meson: axg-audio: move bindings include to main driver
  clk: meson: meson8b: move bindings include to main driver
  clk: meson: a1: move bindings include to main driver
  clk: meson: eeclk: move bindings include to main driver
  clk: meson: aoclk: move bindings include to main driver
  dt-bindings: clk: axg-audio-clkc: expose all clock ids
  dt-bindings: clk: amlogic,a1-pll-clkc: expose all clock ids
  dt-bindings: clk: amlogic,a1-peripherals-clkc: expose all clock ids
  dt-bindings: clk: meson8b-clkc: expose all clock ids
  dt-bindings: clk: g12a-aoclkc: expose all clock ids
  dt-bindings: clk: g12a-clks: expose all clock ids
  dt-bindings: clk: axg-clkc: expose all clock ids
  dt-bindings: clk: gxbb-clkc: expose all clock ids
  clk: meson: migrate axg-audio out of hw_onecell_data to drop NR_CLKS
  clk: meson: migrate meson8b out of hw_onecell_data to drop NR_CLKS
  clk: meson: migrate a1 clock drivers out of hw_onecell_data to drop NR_CLKS
  clk: meson: migrate meson-aoclk out of hw_onecell_data to drop NR_CLKS
  ...

* clk-allwinner:
  clk: sunxi-ng: nkm: Prefer current parent rate
  clk: sunxi-ng: a64: select closest rate for pll-video0
  clk: sunxi-ng: div: Support finding closest rate
  clk: sunxi-ng: mux: Support finding closest rate
  clk: sunxi-ng: nkm: Support finding closest rate
  clk: sunxi-ng: nm: Support finding closest rate
  clk: sunxi-ng: Add helper function to find closest rate
  clk: sunxi-ng: Add feature to find closest rate
  clk: sunxi-ng: a64: allow pll-mipi to set parent's rate
  clk: sunxi-ng: nkm: consider alternative parent rates when determining rate
  clk: sunxi-ng: nkm: Use correct parameter name for parent HW
  clk: sunxi-ng: Modify mismatched function name
  clk: sunxi: sun9i-mmc: Use devm_platform_get_and_ioremap_resource()

* clk-rockchip:
  clk: rockchip: rv1126: Add PD_VO clock tree
  clk: rockchip: rk3568: Fix PLL rate setting for 78.75MHz
  clk: rockchip: rk3568: Add PLL rate for 101MHz

Merge branches 'clk-bindings', 'clk-starfive', 'clk-rm', 'clk-renesas' and 'clk-cleanup' into clk-next

- Remove OXNAS clk driver

* clk-bindings:
  dt-bindings: clock: versal: Convert the xlnx,zynqmp-clk.txt to yaml
  dt-bindings: clock: xlnx,versal-clk: drop select:false
  dt-bindings: clock: versal: Add versal-net compatible string
  dt-bindings: clock: ast2600: Add I3C and MAC reset definitions
  dt-bindings: arm: hisilicon,cpuctrl: Merge "hisilicon,hix5hd2-clock" into parent binding

* clk-starfive:
  reset: starfive: jh7110: Add StarFive STG/ISP/VOUT resets support
  clk: starfive: Simplify .determine_rate()
  clk: starfive: Add StarFive JH7110 Video-Output clock driver
  clk: starfive: Add StarFive JH7110 Image-Signal-Process clock driver
  clk: starfive: Add StarFive JH7110 System-Top-Group clock driver
  clk: starfive: jh7110-sys: Add PLL clocks source from DTS
  clk: starfive: Add StarFive JH7110 PLL clock driver
  dt-bindings: clock: Add StarFive JH7110 Video-Output clock and reset generator
  dt-bindings: clock: Add StarFive JH7110 Image-Signal-Process clock and reset generator
  dt-bindings: clock: Add StarFive JH7110 System-Top-Group clock and reset generator
  dt-bindings: clock: jh7110-syscrg: Add PLL clock inputs
  dt-bindings: soc: starfive: Add StarFive syscon module
  dt-bindings: clock: Add StarFive JH7110 PLL clock generator

* clk-rm:
  dt-bindings: clk: oxnas: remove obsolete bindings
  clk: oxnas: remove obsolete clock driver

* clk-renesas:
  clk: renesas: rcar-gen3: Add ADG clocks
  clk: renesas: r8a77965: Add 3DGE and ZG support
  clk: renesas: r8a7796: Add 3DGE and ZG support
  clk: renesas: r8a7795: Add 3DGE and ZG support
  clk: renesas: emev2: Remove obsolete clkdev registration
  clk: renesas: r9a07g043: Add MTU3a clock and reset entry
  clk: renesas: rzg2l: Simplify .determine_rate()
  clk: renesas: r9a09g011: Add CSI related clocks
  clk: renesas: r8a774b1: Add 3DGE and ZG support
  clk: renesas: r8a774e1: Add 3DGE and ZG support
  clk: renesas: r8a774a1: Add 3DGE and ZG support
  clk: renesas: rcar-gen3: Add support for ZG clock

* clk-cleanup:
  clk: mvebu: Convert to devm_platform_ioremap_resource()
  clk: nuvoton: Convert to devm_platform_ioremap_resource()
  clk: socfpga: agilex: Convert to devm_platform_ioremap_resource()
  clk: ti: Use devm_platform_get_and_ioremap_resource()
  clk: mediatek: Convert to devm_platform_ioremap_resource()
  clk: hsdk-pll: Convert to devm_platform_ioremap_resource()
  clk: gemini: Convert to devm_platform_ioremap_resource()
  clk: fsl-sai: Convert to devm_platform_ioremap_resource()
  clk: bm1880: Convert to devm_platform_ioremap_resource()
  clk: axm5516: Convert to devm_platform_ioremap_resource()
  clk: actions: Convert to devm_platform_ioremap_resource()
  clk: cdce925: Remove redundant of_match_ptr()
  drivers: clk: keystone: Fix parameter judgment in _of_pll_clk_init()
  clk: Explicitly include correct DT includes

clk: lmk04832: Support using PLL1_LD as SPI readback pin

The PLL1_PD pin (a.k.a. STATUS_LD1) can be used as SPI readback pin. Make
this possible.

Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Link: https://lore.kernel.org/r/20230802064100.15793-3-mike.looijmans@topic.nl
Reviewed-by: Liam Beguin <liambeguin@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>

clk: lmk04832: Don't disable vco clock on probe fail

The probe() method never calls clk_prepare_enable(), so it should not
call clk_disable_unprepare() for the vco.clk in the error path. Fixes
a "lmk-vco already disabled" BUG when probe fails.

Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Link: https://lore.kernel.org/r/20230802064100.15793-2-mike.looijmans@topic.nl
Reviewed-by: Liam Beguin <liambeguin@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>

clk: lmk04832: Set missing parent_names for output clocks

lmk04832_register_clkout forgot to fill in the parent_names, resulting
in the error message "Must specify parents if num_parents > 0".

Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Link: https://lore.kernel.org/r/20230802064100.15793-1-mike.looijmans@topic.nl
Reviewed-by: Liam Beguin <liambeguin@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>

clk: mvebu: Convert to devm_platform_ioremap_resource()

Use devm_platform_ioremap_resource() to simplify code.

Signed-off-by: Yangtao Li <frank.li@vivo.com>
Link: https://lore.kernel.org/r/20230705065313.67043-13-frank.li@vivo.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>

clk: nuvoton: Convert to devm_platform_ioremap_resource()

Use devm_platform_ioremap_resource() to simplify code.

Signed-off-by: Yangtao Li <frank.li@vivo.com>
Link: https://lore.kernel.org/r/20230705065313.67043-12-frank.li@vivo.com
Acked-by: Jacky Huang <ychuang3@nuvoton.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>

clk: socfpga: agilex: Convert to devm_platform_ioremap_resource()

Use devm_platform_ioremap_resource() to simplify code.

Signed-off-by: Yangtao Li <frank.li@vivo.com>
Link: https://lore.kernel.org/r/20230705065313.67043-11-frank.li@vivo.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>

clk: ti: Use devm_platform_get_and_ioremap_resource()

Convert platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.

Signed-off-by: Yangtao Li <frank.li@vivo.com>
Link: https://lore.kernel.org/r/20230705065313.67043-10-frank.li@vivo.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>

clk: mediatek: Convert to devm_platform_ioremap_resource()

Use devm_platform_ioremap_resource() to simplify code.

Signed-off-by: Yangtao Li <frank.li@vivo.com>
Link: https://lore.kernel.org/r/20230705065313.67043-9-frank.li@vivo.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>

clk: hsdk-pll: Convert to devm_platform_ioremap_resource()

Use devm_platform_ioremap_resource() to simplify code.

Signed-off-by: Yangtao Li <frank.li@vivo.com>
Link: https://lore.kernel.org/r/20230705065313.67043-7-frank.li@vivo.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>

clk: gemini: Convert to devm_platform_ioremap_resource()

Use devm_platform_ioremap_resource() to simplify code.

Signed-off-by: Yangtao Li <frank.li@vivo.com>
Link: https://lore.kernel.org/r/20230705065313.67043-6-frank.li@vivo.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>

clk: fsl-sai: Convert to devm_platform_ioremap_resource()

Use devm_platform_ioremap_resource() to simplify code.

Signed-off-by: Yangtao Li <frank.li@vivo.com>
Link: https://lore.kernel.org/r/20230705065313.67043-5-frank.li@vivo.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>

clk: bm1880: Convert to devm_platform_ioremap_resource()

Use devm_platform_ioremap_resource() to simplify code.

Signed-off-by: Yangtao Li <frank.li@vivo.com>
Link: https://lore.kernel.org/r/20230705065313.67043-4-frank.li@vivo.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>

clk: axm5516: Convert to devm_platform_ioremap_resource()

Use devm_platform_ioremap_resource() to simplify code.

Signed-off-by: Yangtao Li <frank.li@vivo.com>
Link: https://lore.kernel.org/r/20230705065313.67043-3-frank.li@vivo.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>

clk: actions: Convert to devm_platform_ioremap_resource()

Use devm_platform_ioremap_resource() to simplify code.

Signed-off-by: Yangtao Li <frank.li@vivo.com>
Link: https://lore.kernel.org/r/20230705065313.67043-2-frank.li@vivo.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>

clk: cdce925: Remove redundant of_match_ptr()

The driver depends on CONFIG_OF, it is not necessary to use
of_match_ptr() here.

Signed-off-by: Ruan Jinjie <ruanjinjie@huawei.com>
Link: https://lore.kernel.org/r/20230808125341.4073115-1-ruanjinjie@huawei.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>

clk: pxa910: Move number of clocks to driver source

The number of clocks should not be in the dt binding as it is not used
by the respective device tree and thus needlessly bloats the ABI.

Move this number of clocks into the driver source.

Signed-off-by: Duje Mihanović <duje.mihanovic@skole.hr>
Link: https://lore.kernel.org/r/20230812-mmp-nr-clks-v2-4-f9271bd7eaa5@skole.hr
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>

clk: pxa1928: Move number of clocks to driver source

The number of clocks should not be in the dt binding as it is not used
by the respective device tree and thus needlessly bloats the ABI.

Move this number of clocks into the driver source.

Signed-off-by: Duje Mihanović <duje.mihanovic@skole.hr>
Link: https://lore.kernel.org/r/20230812-mmp-nr-clks-v2-3-f9271bd7eaa5@skole.hr
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>

clk: pxa168: Move number of clocks to driver source

The number of clocks should not be in the dt binding as it is not used
by the respective device tree and thus needlessly bloats the ABI.

Move this number of clocks into the driver source.

Signed-off-by: Duje Mihanović <duje.mihanovic@skole.hr>
Link: https://lore.kernel.org/r/20230812-mmp-nr-clks-v2-2-f9271bd7eaa5@skole.hr
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>

clk: mmp2: Move number of clocks to driver source

The number of clocks should not be in the dt binding as it is not used
by the respective device tree and thus needlessly bloats the ABI.

Move this number of clocks into the driver source.

Signed-off-by: Duje Mihanović <duje.mihanovic@skole.hr>
Link: https://lore.kernel.org/r/20230812-mmp-nr-clks-v2-1-f9271bd7eaa5@skole.hr
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>

clk: mmp: Remove old non-OF clock drivers

There are no MMP2, PXA168 or PXA910 boards still using board files which
would use these drivers, so remove them.

Signed-off-by: Duje Mihanović <duje.mihanovic@skole.hr>
Link: https://lore.kernel.org/r/20230804-drop-old-mmp-clk-v1-1-0c07db6cee90@skole.hr
Signed-off-by: Stephen Boyd <sboyd@kernel.org>

clk: qcom: clk-spmi-pmic-div: Annotate struct spmi_pmic_div_clk_cc with __counted_by

Prepare for the coming implementation by GCC and Clang of the __counted_by
attribute. Flexible array members annotated with __counted_by can have
their accesses bounds-checked at run-time checking via CONFIG_UBSAN_BOUNDS
(for array indexing) and CONFIG_FORTIFY_SOURCE (for strcpy/memcpy-family
functions).

As found with Coccinelle[1], add __counted_by for struct spmi_pmic_div_clk_cc.

[1] https://github.com/kees/kernel-tools/blob/trunk/coccinelle/examples/counted_by.cocci

Cc: Bjorn Andersson <andersson@kernel.org>
Cc: Andy Gross <agross@kernel.org>
Cc: Konrad Dybcio <konrad.dybcio@linaro.org>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: linux-arm-msm@vger.kernel.org
Cc: linux-clk@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20230817202941.never.657-kees@kernel.org
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>

clk: Annotate struct clk_hw_onecell_data with __counted_by

Prepare for the coming implementation by GCC and Clang of the __counted_by
attribute. Flexible array members annotated with __counted_by can have
their accesses bounds-checked at run-time checking via CONFIG_UBSAN_BOUNDS
(for array indexing) and CONFIG_FORTIFY_SOURCE (for strcpy/memcpy-family
functions).

As found with Coccinelle[1], add __counted_by for struct clk_hw_onecell_data.
Additionally, since the element count member must be set before accessing
the annotated flexible array member, move its initialization earlier.

[1] https://github.com/kees/kernel-tools/blob/trunk/coccinelle/examples/counted_by.cocci

Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Joel Stanley <joel@jms.id.au>
Cc: Andrew Jeffery <andrew@aj.id.au>
Cc: Taichi Sugaya <sugaya.taichi@socionext.com>
Cc: Takao Orito <orito.takao@socionext.com>
Cc: Qin Jian <qinjian@cqplus1.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Gregory Clement <gregory.clement@bootlin.com>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <andersson@kernel.org>
Cc: Konrad Dybcio <konrad.dybcio@linaro.org>
Cc: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Jernej Skrabec <jernej.skrabec@gmail.com>
Cc: David Airlie <airlied@gmail.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Samuel Holland <samuel@sholland.org>
Cc: Vinod Koul <vkoul@kernel.org>
Cc: Kishon Vijay Abraham I <kishon@kernel.org>
Cc: linux-clk@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-aspeed@lists.ozlabs.org
Cc: linux-arm-msm@vger.kernel.org
Cc: linux-mediatek@lists.infradead.org
Cc: dri-devel@lists.freedesktop.org
Cc: linux-sunxi@lists.linux.dev
Cc: linux-phy@lists.infradead.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20230817203019.never.795-kees@kernel.org
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>

clk: vc7: Use i2c_get_match_data() instead of device_get_match_data()

The device_get_match_data(), is to get match data for firmware interfaces
such as just OF/ACPI. This driver has I2C matching table as well. Use
i2c_get_match_data() to get match data for I2C, ACPI and DT-based
matching.

Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230721070019.96627-3-biju.das.jz@bp.renesas.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>

clk: vc5: Use i2c_get_match_data() instead of device_get_match_data()

The device_get_match_data(), is to get match data for firmware interfaces
such as just OF/ACPI. This driver has I2C matching table as well. Use
i2c_get_match_data() to get match data for I2C, ACPI and DT-based
matching.

Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230721070019.96627-2-biju.das.jz@bp.renesas.com
Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>

Merge tag 'samsung-clk-6.6' of https://git./linux/kernel/git/krzk/linux into clk-samsung

Pull Samsung SoC clock drivers changes from Krzysztof Kozlowski:

Remove from the bindings the #defines with number of clocks supported by
each clock controller driver.  This number can vary, e.g. when we
implement more clocks in the driver.  Having the number in the bindings
prevents changing it.  Instead, this should be just a #define inside the
driver.

* tag 'samsung-clk-6.6' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
  dt-bindings: clock: samsung: remove define with number of clocks
  clk: samsung: exynoautov9: do not define number of clocks in bindings
  clk: samsung: exynos850: do not define number of clocks in bindings
  clk: samsung: exynos7885: do not define number of clocks in bindings
  clk: samsung: exynos5433: do not define number of clocks in bindings
  clk: samsung: exynos5420: do not define number of clocks in bindings
  clk: samsung: exynos5410: do not define number of clocks in bindings
  clk: samsung: exynos5260: do not define number of clocks in bindings
  clk: samsung: exynos5250: do not define number of clocks in bindings
  clk: samsung: exynos4: do not define number of clocks in bindings
  clk: samsung: exynos3250: do not define number of clocks in bindings

Merge tag 'clk-imx-6.6' of git://git./linux/kernel/git/abelvesa/linux into clk-imx

Pull i.MX clk driver updates from Abel Vesa:

- Add the PDM IPC clock for i.MX93
- Add 519.75MHz frequency support for i.MX9 PLL
- Simplify the .determine_rate() for GPR mux
- Make the i.MX8QXP LPCG clock use devm_platform_ioremap_resource
- Add the audio mux clock to i.MX8
- Fix the SPLL2 MULT range for PLLv4
- Update the SPLL2 type in i.MX8ULP
- Fix the SAI4 clock on i.MX8MP
- Add silicon revision print for i.MX25 on clocks init
- Drop the return value from __mx25_clocks_init
- Fix the clock pauses on no-op set_rate for i.MX8M composite clock
- Drop restrictions for PLL14xx and fix its max prediv value
- Drop the 393216000 and 361267200 from PLL14xx rate table to allow
   glitch free switching

* tag 'clk-imx-6.6' of git://git.kernel.org/pub/scm/linux/kernel/git/abelvesa/linux:
  clk: imx: pll14xx: dynamically configure PLL for 393216000/361267200Hz
  clk: imx: pll14xx: align pdiv with reference manual
  clk: imx: composite-8m: fix clock pauses when set_rate would be a no-op
  clk: imx25: make __mx25_clocks_init return void
  clk: imx25: print silicon revision during init
  dt-bindings: clocks: imx8mp: make sai4 a dummy clock
  clk: imx8mp: fix sai4 clock
  clk: imx: imx8ulp: update SPLL2 type
  clk: imx: pllv4: Fix SPLL2 MULT range
  clk: imx: imx8: add audio clock mux driver
  dt-bindings: clock: fsl,imx8-acm: Add audio clock mux support
  clk: imx: clk-imx8qxp-lpcg: Convert to devm_platform_ioremap_resource()
  clk: imx: clk-gpr-mux: Simplify .determine_rate()
  clk: imx: Add 519.75MHz frequency support for imx9 pll
  clk: imx93: Add PDM IPG clk
  dt-bindings: clock: imx93: Add PDM IPG clk

Merge tag 'v6.6-rockchip-clk1' of git://git./linux/kernel/git/mmind/linux-rockchip into clk-rockchip

Pull Rockchip clk driver updates from Heiko Stuebner:

- PLL rates for rk3568 and the display clock tree for rv1126 which wasn't present before

* tag 'v6.6-rockchip-clk1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
  clk: rockchip: rv1126: Add PD_VO clock tree
  clk: rockchip: rk3568: Fix PLL rate setting for 78.75MHz
  clk: rockchip: rk3568: Add PLL rate for 101MHz

Merge tag 'renesas-clk-for-v6.6-tag2' of git://git./linux/kernel/git/geert/renesas-drivers into clk-renesas

Pull another Renesas clk driver update from Geert Uytterhoeven:

- Add Audio Clock Generator (ADG) clocks on R-Car Gen3 and RZ/G2 SoCs

* tag 'renesas-clk-for-v6.6-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers:
clk: renesas: rcar-gen3: Add ADG clocks

dt-bindings: clock: samsung: remove define with number of clocks

Number of clocks supported by Linux drivers might vary - sometimes we
add new clocks, not exposed previously. Therefore these numbers of
clocks should not be in the bindings, as that prevents changing them.
Remove it entirely from the bindings, once Linux drivers stopped using
them.

Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Link: https://lore.kernel.org/r/20230808082738.122804-12-krzysztof.kozlowski@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>

clk: samsung: exynoautov9: do not define number of clocks in bindings

Number of clocks supported by Linux drivers might vary - sometimes we
add new clocks, not exposed previously. Therefore these numbers of
clocks should not be in the bindings, as that prevents changing them.

Define number of clocks per each clock controller inside the driver
directly.

Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Link: https://lore.kernel.org/r/20230808082738.122804-11-krzysztof.kozlowski@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>

clk: samsung: exynos850: do not define number of clocks in bindings

Number of clocks supported by Linux drivers might vary - sometimes we
add new clocks, not exposed previously. Therefore these numbers of
clocks should not be in the bindings, as that prevents changing them.

Define number of clocks per each clock controller inside the driver
directly.

Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Link: https://lore.kernel.org/r/20230808082738.122804-10-krzysztof.kozlowski@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>

clk: samsung: exynos7885: do not define number of clocks in bindings

Number of clocks supported by Linux drivers might vary - sometimes we
add new clocks, not exposed previously. Therefore these numbers of
clocks should not be in the bindings, as that prevents changing them.

Define number of clocks per each clock controller inside the driver
directly.

Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Link: https://lore.kernel.org/r/20230808082738.122804-9-krzysztof.kozlowski@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>

clk: samsung: exynos5433: do not define number of clocks in bindings

Number of clocks supported by Linux drivers might vary - sometimes we
add new clocks, not exposed previously. Therefore these numbers of
clocks should not be in the bindings, as that prevents changing them.

Define number of clocks per each clock controller inside the driver
directly.

Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Link: https://lore.kernel.org/r/20230808082738.122804-8-krzysztof.kozlowski@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>

clk: samsung: exynos5420: do not define number of clocks in bindings

Number of clocks supported by Linux drivers might vary - sometimes we
add new clocks, not exposed previously. Therefore these numbers of
clocks should not be in the bindings, as that prevents changing them.

Define number of clocks per each clock controller inside the driver
directly.

Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Link: https://lore.kernel.org/r/20230808082738.122804-7-krzysztof.kozlowski@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>

clk: samsung: exynos5410: do not define number of clocks in bindings

Number of clocks supported by Linux drivers might vary - sometimes we
add new clocks, not exposed previously. Therefore these numbers of
clocks should not be in the bindings, as that prevents changing them.

Define number of clocks per each clock controller inside the driver
directly.

Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Link: https://lore.kernel.org/r/20230808082738.122804-6-krzysztof.kozlowski@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>

clk: samsung: exynos5260: do not define number of clocks in bindings

Number of clocks supported by Linux drivers might vary - sometimes we
add new clocks, not exposed previously. Therefore these numbers of
clocks should not be in the bindings, as that prevents changing them.

Define number of clocks per each clock controller inside the driver
directly.

Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Link: https://lore.kernel.org/r/20230808082738.122804-5-krzysztof.kozlowski@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>

clk: samsung: exynos5250: do not define number of clocks in bindings

Number of clocks supported by Linux drivers might vary - sometimes we
add new clocks, not exposed previously. Therefore these numbers of
clocks should not be in the bindings, as that prevents changing them.

Define number of clocks per each clock controller inside the driver
directly.

Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Link: https://lore.kernel.org/r/20230808082738.122804-4-krzysztof.kozlowski@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>

clk: samsung: exynos4: do not define number of clocks in bindings

Number of clocks supported by Linux drivers might vary - sometimes we
add new clocks, not exposed previously. Therefore these numbers of
clocks should not be in the bindings, as that prevents changing them.

Define number of clocks per each clock controller inside the driver
directly.

Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Link: https://lore.kernel.org/r/20230808082738.122804-3-krzysztof.kozlowski@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>

clk: samsung: exynos3250: do not define number of clocks in bindings

Number of clocks supported by Linux drivers might vary - sometimes we
add new clocks, not exposed previously. Therefore these numbers of
clocks should not be in the bindings, as that prevents changing them.

Define number of clocks per each clock controller inside the driver
directly.

Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Link: https://lore.kernel.org/r/20230808082738.122804-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>

Merge tag 'sunxi-clk-for-6.6-2' of https://git./linux/kernel/git/sunxi/linux into clk-allwinner

Pull Allwinner clk driver changes from Chen-Yu Tsai:

- Parameter name correction for ccu_nkm_round_rate()
- Implement CLK_SET_RATE_PARENT for NKM clocks, i.e. consider alternative
   parent rates when determining clock rates
- Set CLK_SET_RATE_PARENT for A64 pll-mipi
- Support finding closest (as opposed to closest but not higher) clock
   rate for NM, NKM, mux and div type clocks, as use it for A64
   pll-video0
- Prefer current parent rate if able to generate ideal clock rate for
   NKM clocks

* tag 'sunxi-clk-for-6.6-2' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
  clk: sunxi-ng: nkm: Prefer current parent rate
  clk: sunxi-ng: a64: select closest rate for pll-video0
  clk: sunxi-ng: div: Support finding closest rate
  clk: sunxi-ng: mux: Support finding closest rate
  clk: sunxi-ng: nkm: Support finding closest rate
  clk: sunxi-ng: nm: Support finding closest rate
  clk: sunxi-ng: Add helper function to find closest rate
  clk: sunxi-ng: Add feature to find closest rate
  clk: sunxi-ng: a64: allow pll-mipi to set parent's rate
  clk: sunxi-ng: nkm: consider alternative parent rates when determining rate
  clk: sunxi-ng: nkm: Use correct parameter name for parent HW

clk: imx: pll14xx: dynamically configure PLL for 393216000/361267200Hz

Since commit b09c68dc57c9 ("clk: imx: pll14xx: Support dynamic rates"),
the driver has the ability to dynamically compute PLL parameters to
approximate the requested rates. This is not always used, because the
logic is as follows:

  - Check if the target rate is hardcoded in the frequency table
  - Check if varying only kdiv is possible, so switch over is glitch free
  - Compute rate dynamically by iterating over pdiv range

If we skip the frequency table for the 1443x PLL, we find that the
computed values differ to the hardcoded ones. This can be valid if the
hardcoded values guarantee for example an earlier lock-in or if the
divisors are chosen, so that other important rates are more likely to
be reached glitch-free.

For rates (393216000 and 361267200, this doesn't seem to be the case:
They are only approximated by existing parameters (393215995 and
361267196 Hz, respectively) and they aren't reachable glitch-free from
other hardcoded frequencies. Dropping them from the table allows us
to lock-in to these frequencies exactly.

This is immediately noticeable because they are the assigned-clock-rates
for IMX8MN_AUDIO_PLL1 and IMX8MN_AUDIO_PLL2, respectively and a look
into clk_summary so far showed that they were a few Hz short of the target:

imx8mn-board:~# grep audio_pll[12]_out /sys/kernel/debug/clk/clk_summary
audio_pll2_out           0        0        0   361267196 0     0  50000   N
audio_pll1_out           1        1        0   393215995 0     0  50000   Y

and afterwards:

imx8mn-board:~# grep audio_pll[12]_out /sys/kernel/debug/clk/clk_summary
audio_pll2_out           0        0        0   361267200 0     0  50000   N
audio_pll1_out           1        1        0   393216000 0     0  50000   Y

This change is equivalent to adding following hardcoded values:

  /*               rate     mdiv  pdiv  sdiv   kdiv */
  PLL_1443X_RATE(393216000, 655,    5,    3,  23593),
  PLL_1443X_RATE(361267200, 497,   33,    0, -16882),

Fixes: 053a4ffe2988 ("clk: imx: imx8mm: fix audio pll setting")
Cc: stable@vger.kernel.org # v5.18+
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Link: https://lore.kernel.org/r/20230807084744.1184791-2-m.felsch@pengutronix.de
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>

clk: imx: pll14xx: align pdiv with reference manual

The PLL14xx hardware can be found on i.MX8M{M,N,P} SoCs and always come
with a 6-bit pre-divider. Neither the reference manuals nor the
datasheets of these SoCs do mention any restrictions. Furthermore the
current code doesn't respect the restrictions from the comment too.

Therefore drop the restriction and align the max pre-divider (pdiv)
value to 63 to get more accurate frequencies.

Fixes: b09c68dc57c9 ("clk: imx: pll14xx: Support dynamic rates")
Cc: stable@vger.kernel.org
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Tested-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Link: https://lore.kernel.org/r/20230807084744.1184791-1-m.felsch@pengutronix.de
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>

clk: imx: composite-8m: fix clock pauses when set_rate would be a no-op

Reconfiguring the clock divider to the exact same value is observed
on an i.MX8MN to often cause a longer than usual clock pause, probably
because the divider restarts counting whenever the register is rewritten.

This issue doesn't show up normally, because the clock framework will
take care to not call set_rate when the clock rate is the same.
However, when we reconfigure an upstream clock, the common code will
call set_rate with the newly calculated rate on all children, e.g.:

  - sai5 is running normally and divides Audio PLL out by 16.
  - Audio PLL rate is increased by 32Hz (glitch-free kdiv change)
  - rates for children are recalculated and rates are set recursively
  - imx8m_clk_composite_divider_set_rate(sai5) is called with
    32/16 = 2Hz more
  - imx8m_clk_composite_divider_set_rate computes same divider as before
  - divider register is written, so it restarts counting from zero and
    MCLK is briefly paused, so instead of e.g. 40ns, MCLK is low for 120ns.

Some external clock consumers can be upset by such unexpected clock pauses,
so let's make sure we only rewrite the divider value when the value to be
written is actually different.

Fixes: d3ff9728134e ("clk: imx: Add imx composite clock")
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Link: https://lore.kernel.org/r/20230807082201.2332746-1-a.fatoum@pengutronix.de
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>

clk: imx25: make __mx25_clocks_init return void

The __mx25_clocks_init function always returns 0 and its only
caller does not check the return value. Let's remove it.

Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/20230802184046.153394-3-martin@kaiser.cx
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>

clk: imx25: print silicon revision during init

Print the imx25 silicon revision when the clocks are initialised.

Use the same mechanism as for imx27, i.e. call mx25_revision.
This function is unused at the moment.

Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/20230802184046.153394-2-martin@kaiser.cx
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>

dt-bindings: clocks: imx8mp: make sai4 a dummy clock

The hardware don't have a SAI4 instance so remove the define. Use a
comment to keep it as reference and to avoid confusion.

Fixes: 108869144739 ("dt-bindings: imx: Add clock binding doc for i.MX8MP")
Acked-by: Stephen Boyd <sboyd@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Link: https://lore.kernel.org/r/20230731142150.3186650-2-m.felsch@pengutronix.de
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>

clk: imx8mp: fix sai4 clock

The reference manual don't mention a SAI4 hardware block. This would be
clock slice 78 which is skipped (TRM, page 237). Remove any reference to
this clock to align the driver with the reality.

Fixes: 9c140d992676 ("clk: imx: Add support for i.MX8MP clock driver")
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Link: https://lore.kernel.org/r/20230731142150.3186650-1-m.felsch@pengutronix.de
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>

clk: imx: imx8ulp: update SPLL2 type

The SPLL2 on iMX8ULP is different with other frac PLLs, it can
support VCO from 650Mhz to 1Ghz. Following the changes to pllv4,
use the new type IMX_PLLV4_IMX8ULP_1GHZ.

Fixes: c43a801a5789 ("clk: imx: Add clock driver for imx8ulp")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20230625123340.4067536-2-peng.fan@oss.nxp.com
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>

clk: imx: pllv4: Fix SPLL2 MULT range

The SPLL2 on iMX8ULP is different with other frac PLLs, it can
support VCO from 650Mhz to 1Ghz. According to RM, the MULT is
using a range from 27 to 54, not some fixed values. If using
current PLL implementation, some clock rate can't be supported.

Fix the issue by adding new type for the SPLL2 and use MULT range
to replace MULT table

Fixes: 5f0601c47c33 ("clk: imx: Update the pllv4 to support imx8ulp")
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20230625123340.4067536-1-peng.fan@oss.nxp.com
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>

clk: imx: imx8: add audio clock mux driver

The Audio Clock Mux (ACM) is a collection of control registers
and multiplexers that are used to route the audio source clocks
to the audio peripherals.

Each audio peripheral has its dedicated audio clock mux
(which differ based on usage) and control register.

Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/1690260984-25744-3-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>

dt-bindings: clock: fsl,imx8-acm: Add audio clock mux support

Add the clock dt-binding file for Audio Clock Mux. which
is the IP for i.MX8QM, i.MX8QXP, i.MX8DXL.

Add the clockid for clocks in header file.

The Audio Clock Mux is binded with all the audio IP and audio clocks
in the subsystem, so need to list the power domain of related clocks
and IPs. Each clock and IP has a power domain, so there are so many
power domains.

Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/1690260984-25744-2-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>

clk: imx: clk-imx8qxp-lpcg: Convert to devm_platform_ioremap_resource()

Use devm_platform_ioremap_resource() to simplify code.

Signed-off-by: Yangtao Li <frank.li@vivo.com>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20230705065313.67043-8-frank.li@vivo.com
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>

clk: rockchip: rv1126: Add PD_VO clock tree

PD_VO clock tree diagram in RV1126 is connected to
- BIU_VO
- VOP
- RGA
- IEP
- DSIHOST

Add entire PD_VO clock tree for rv1126.

Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Link: https://lore.kernel.org/r/20230731110012.2913742-3-jagan@edgeble.ai
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

Merge tag 'sunxi-clk-for-6.6-1' of https://git./linux/kernel/git/sunxi/linux into clk-allwinner

Pull Allwinner clk driver updates from Jernej Skrabec:

- Convert sun9i-mmc clock to use devm_platform_get_and_ioremap_resource()
- Fix function name in a comment in ccu_mmc_timing.c

* tag 'sunxi-clk-for-6.6-1' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
clk: sunxi-ng: Modify mismatched function name
clk: sunxi: sun9i-mmc: Use devm_platform_get_and_ioremap_resource()

Merge tag 'clk-meson-v6.6-1' of https://github.com/BayLibre/clk-meson into clk-amlogic

Pull Amlogic clk driver updates from Jerome Brunet:

- dt-bindings: expose all Amlogic clock ids
- Migrate Amlogic gxbb clock controllers dt-bindings to schema

* tag 'clk-meson-v6.6-1' of https://github.com/BayLibre/clk-meson: (22 commits)
  dt-bindings: soc: amlogic: document System Control registers
  dt-bindings: clock: amlogic: convert amlogic,gxbb-aoclkc.txt to dt-schema
  dt-bindings: clock: amlogic: convert amlogic,gxbb-clkc.txt to dt-schema
  clk: meson: axg-audio: move bindings include to main driver
  clk: meson: meson8b: move bindings include to main driver
  clk: meson: a1: move bindings include to main driver
  clk: meson: eeclk: move bindings include to main driver
  clk: meson: aoclk: move bindings include to main driver
  dt-bindings: clk: axg-audio-clkc: expose all clock ids
  dt-bindings: clk: amlogic,a1-pll-clkc: expose all clock ids
  dt-bindings: clk: amlogic,a1-peripherals-clkc: expose all clock ids
  dt-bindings: clk: meson8b-clkc: expose all clock ids
  dt-bindings: clk: g12a-aoclkc: expose all clock ids
  dt-bindings: clk: g12a-clks: expose all clock ids
  dt-bindings: clk: axg-clkc: expose all clock ids
  dt-bindings: clk: gxbb-clkc: expose all clock ids
  clk: meson: migrate axg-audio out of hw_onecell_data to drop NR_CLKS
  clk: meson: migrate meson8b out of hw_onecell_data to drop NR_CLKS
  clk: meson: migrate a1 clock drivers out of hw_onecell_data to drop NR_CLKS
  clk: meson: migrate meson-aoclk out of hw_onecell_data to drop NR_CLKS
  ...

clk: sunxi-ng: nkm: Prefer current parent rate

Similar to ccu_mp, if the current parent rate allows getting the ideal
rate, prefer to not change the parent clock's rate.

Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Frank Oltmanns <frank@oltmanns.dev>
Link: https://lore.kernel.org/r/20230807-pll-mipi_set_rate_parent-v6-11-f173239a4b59@oltmanns.dev
Signed-off-by: Chen-Yu Tsai <wens@csie.org>

clk: sunxi-ng: a64: select closest rate for pll-video0

Selecting the closest rate for pll-video0 instead of the closest rate
that is less than the requested rate has no downside for this clock,
while allowing for selecting a more suitable rate, e.g. for the
connected panels.

Furthermore, the algorithm that sets an NKM clock's parent benefits from
the closest rate. Without it, the NKM clock's rate might drift away from
the requested rate in the multiple successive calls to
ccu_nkm_determine_rate that the clk framework performs when setting a
clock rate.

Therefore, configure pll-video0 and, in consequence, all of its
descendents to select the closest rate.

Acked-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Frank Oltmanns <frank@oltmanns.dev>
Link: https://lore.kernel.org/r/20230807-pll-mipi_set_rate_parent-v6-10-f173239a4b59@oltmanns.dev
Signed-off-by: Chen-Yu Tsai <wens@csie.org>

clk: sunxi-ng: div: Support finding closest rate

Add initalization macros for divisor clocks with mux
(SUNXI_CCU_M_WITH_MUX) to support finding the closest rate. This clock
type requires the appropriate flags to be set in the .common structure
(for the mux part of the clock) and the .div part.

Acked-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Frank Oltmanns <frank@oltmanns.dev>
Link: https://lore.kernel.org/r/20230807-pll-mipi_set_rate_parent-v6-9-f173239a4b59@oltmanns.dev
Signed-off-by: Chen-Yu Tsai <wens@csie.org>

clk: sunxi-ng: mux: Support finding closest rate

When finding the best rate for a mux clock, consider rates that are
higher than the requested rate when CCU_FEATURE_ROUND_CLOSEST is used.
Furthermore, introduce an initialization macro that sets this flag.

Acked-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Frank Oltmanns <frank@oltmanns.dev>
Link: https://lore.kernel.org/r/20230807-pll-mipi_set_rate_parent-v6-8-f173239a4b59@oltmanns.dev
Signed-off-by: Chen-Yu Tsai <wens@csie.org>

clk: sunxi-ng: nkm: Support finding closest rate

When finding the best rate for a NKM clock, consider rates that are
higher than the requested rate, if the CCU_FEATURE_CLOSEST_RATE flag is
set by using the helper function ccu_is_better_rate().

Accommodate ccu_mux_helper_determine_rate to this change.

Acked-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Frank Oltmanns <frank@oltmanns.dev>
Link: https://lore.kernel.org/r/20230807-pll-mipi_set_rate_parent-v6-7-f173239a4b59@oltmanns.dev
Signed-off-by: Chen-Yu Tsai <wens@csie.org>

clk: sunxi-ng: nm: Support finding closest rate

Use the helper function ccu_is_better_rate() to determine the rate that
is closest to the requested rate, thereby supporting rates that are
higher than the requested rate if the clock uses the
CCU_FEATURE_CLOSEST_RATE.

Add the macro SUNXI_CCU_NM_WITH_FRAC_GATE_LOCK_MIN_MAX_CLOSEST which
sets CCU_FEATURE_CLOSEST_RATE.

To avoid code duplication, add the macros
SUNXI_CCU_NM_WITH_FRAC_GATE_LOCK_MIN_MAX_FEAT that allows selecting
arbitrary features and use it in the original
SUNXI_CCU_NM_WITH_FRAC_GATE_LOCK_MIN_MAX as well as the newly introduced
SUNXI_CCU_NM_WITH_FRAC_GATE_LOCK_MIN_MAX_CLOSEST macros.

Acked-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Frank Oltmanns <frank@oltmanns.dev>
Link: https://lore.kernel.org/r/20230807-pll-mipi_set_rate_parent-v6-6-f173239a4b59@oltmanns.dev
Signed-off-by: Chen-Yu Tsai <wens@csie.org>

clk: sunxi-ng: Add helper function to find closest rate

The default behaviour of clocks in the sunxi-ng driver is to select a
clock rate that is closest to but less than the requested rate.

Add the ccu_is_better_rate() helper function that - depending on the
fact if thc CCU_FEATURE_CLOSEST_RATE flag is set - decides if a rate is
closer than another rate.

Acked-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Frank Oltmanns <frank@oltmanns.dev>
Link: https://lore.kernel.org/r/20230807-pll-mipi_set_rate_parent-v6-5-f173239a4b59@oltmanns.dev
Signed-off-by: Chen-Yu Tsai <wens@csie.org>

clk: sunxi-ng: Add feature to find closest rate

The default behaviour of clocks in the sunxi-ng driver is to select a
clock rate that is closest to but less than the requested rate.

Add the CCU_FEATURE_CLOSEST_RATE flag, which can be used to allow clocks
to find the closest rate instead.

Acked-by: Maxime Ripard <mripard@kernel.org>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Frank Oltmanns <frank@oltmanns.dev>
Link: https://lore.kernel.org/r/20230807-pll-mipi_set_rate_parent-v6-4-f173239a4b59@oltmanns.dev
Signed-off-by: Chen-Yu Tsai <wens@csie.org>

clk: sunxi-ng: a64: allow pll-mipi to set parent's rate

The nkm clock now supports setting the parent's rate. Utilize this
option to find the optimal rate for pll-mipi.

Acked-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Frank Oltmanns <frank@oltmanns.dev>
Link: https://lore.kernel.org/r/20230807-pll-mipi_set_rate_parent-v6-3-f173239a4b59@oltmanns.dev
Signed-off-by: Chen-Yu Tsai <wens@csie.org>

clk: sunxi-ng: nkm: consider alternative parent rates when determining rate

In case the CLK_SET_RATE_PARENT flag is set, consider using a different
parent rate when determining a new rate.

To find the best match for the requested rate, perform the following
steps for each NKM combination:
- calculate the optimal parent rate,
- find the best parent rate that the parent clock actually supports
- use that parent rate to calculate the effective rate.

In case the clk does not support setting the parent rate, use the same
algorithm as before.

Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Frank Oltmanns <frank@oltmanns.dev>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Link: https://lore.kernel.org/r/20230807-pll-mipi_set_rate_parent-v6-2-f173239a4b59@oltmanns.dev
Signed-off-by: Chen-Yu Tsai <wens@csie.org>

clk: sunxi-ng: nkm: Use correct parameter name for parent HW

ccu_nkm_round_rate() takes a clk_hw as parameter "hw". Since "hw" is the
nkm clock's parent clk_hw, not the clk_hw of the nkm clock itself,
change the parameter name to "parent_hw" to make it more clear what
we're dealing with.

Acked-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Frank Oltmanns <frank@oltmanns.dev>
Link: https://lore.kernel.org/r/20230807-pll-mipi_set_rate_parent-v6-1-f173239a4b59@oltmanns.dev
Signed-off-by: Chen-Yu Tsai <wens@csie.org>

dt-bindings: soc: amlogic: document System Control registers

Document the System Control registers regions found on all Amlogic
SoC families and it's clock, power, pinctrl and phy subnodes.

The regions has various independent registers tied to other
hardware devices, thus the syscon compatible.

Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20230706-b4-amlogic-bindings-convert-take2-v3-3-f63de6f12dcc@linaro.org
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>

dt-bindings: clock: amlogic: convert amlogic,gxbb-aoclkc.txt to dt-schema

Convert the Amlogic Always-On Clock Controller bindings to dt-schema.

[jbrunet: Fixed whitespace checkpatch warning]
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230706-b4-amlogic-bindings-convert-take2-v3-2-f63de6f12dcc@linaro.org
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>

dt-bindings: clock: amlogic: convert amlogic,gxbb-clkc.txt to dt-schema

Convert the Amlogic Clock Controller bindings to dt-schema.

Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20230706-b4-amlogic-bindings-convert-take2-v3-1-f63de6f12dcc@linaro.org
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>

clk: meson: axg-audio: move bindings include to main driver

Now the clock ids are no more defined in private headers,
cleanup and include the dt-bindings headers from the main
driver file.

Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20230607-topic-amlogic-upstream-clkid-public-migration-v2-19-38172d17c27a@linaro.org
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>

clk: meson: meson8b: move bindings include to main driver

Now the clock ids are no more defined in private headers,
cleanup and include the dt-bindings headers from the main
driver file.

Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20230607-topic-amlogic-upstream-clkid-public-migration-v2-18-38172d17c27a@linaro.org
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>

clk: meson: a1: move bindings include to main driver

Now the clock ids are no more defined in private headers,
cleanup and include the dt-bindings headers from the main
driver file.

Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Dmitry Rokosov <ddrokosov@sberdevices.ru>
Link: https://lore.kernel.org/r/20230607-topic-amlogic-upstream-clkid-public-migration-v2-17-38172d17c27a@linaro.org
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>

clk: meson: eeclk: move bindings include to main driver

Now the clock ids are no more defined in private headers,
cleanup and include the dt-bindings headers from the main
driver file.

Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20230607-topic-amlogic-upstream-clkid-public-migration-v2-16-38172d17c27a@linaro.org
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>

clk: meson: aoclk: move bindings include to main driver

Now the clock ids are no more defined in private headers,
cleanup and include the dt-bindings headers from the main
driver file.

Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20230607-topic-amlogic-upstream-clkid-public-migration-v2-15-38172d17c27a@linaro.org
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>

dt-bindings: clk: axg-audio-clkc: expose all clock ids

Due to a policy change in clock ID bindings handling, expose
all the "private" clock IDs to the public clock dt-bindings
to move out of the previous maintenance scheme.

This refers to a discussion at [1] & [2] with Krzysztof about
the issue with the current maintenance.

It was decided to move every axg-audio-clkc ID to the public clock
dt-bindings headers to be merged in a single tree so we
can safely add new clocks without having merge issues.

[1] https://lore.kernel.org/all/c088e01c-0714-82be-8347-6140daf56640@linaro.org/
[2] https://lore.kernel.org/all/2fabe721-7434-43e7-bae5-088a42ba128d@app.fastmail.com/

Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20230607-topic-amlogic-upstream-clkid-public-migration-v2-14-38172d17c27a@linaro.org
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>

dt-bindings: clk: amlogic,a1-pll-clkc: expose all clock ids

Due to a policy change in clock ID bindings handling, expose
all the "private" clock IDs to the public clock dt-bindings
to move out of the previous maintenance scheme.

This refers to a discussion at [1] & [2] with Krzysztof about
the issue with the current maintenance.

It was decided to move every A1 pll ID to the public clock
dt-bindings headers to be merged in a single tree so we
can safely add new clocks without having merge issues.

[1] https://lore.kernel.org/all/c088e01c-0714-82be-8347-6140daf56640@linaro.org/
[2] https://lore.kernel.org/all/2fabe721-7434-43e7-bae5-088a42ba128d@app.fastmail.com/

Reviewed-by: Dmitry Rokosov <ddrokosov@sberdevices.ru>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20230607-topic-amlogic-upstream-clkid-public-migration-v2-13-38172d17c27a@linaro.org
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>

dt-bindings: clk: amlogic,a1-peripherals-clkc: expose all clock ids

Due to a policy change in clock ID bindings handling, expose
all the "private" clock IDs to the public clock dt-bindings
to move out of the previous maintenance scheme.

This refers to a discussion at [1] & [2] with Krzysztof about
the issue with the current maintenance.

It was decided to move every A1 peripherals ID to the public clock
dt-bindings headers to be merged in a single tree so we
can safely add new clocks without having merge issues.

[1] https://lore.kernel.org/all/c088e01c-0714-82be-8347-6140daf56640@linaro.org/
[2] https://lore.kernel.org/all/2fabe721-7434-43e7-bae5-088a42ba128d@app.fastmail.com/

Reviewed-by: Dmitry Rokosov <ddrokosov@sberdevices.ru>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20230607-topic-amlogic-upstream-clkid-public-migration-v2-12-38172d17c27a@linaro.org
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>

dt-bindings: clk: meson8b-clkc: expose all clock ids

Due to a policy change in clock ID bindings handling, expose
all the "private" clock IDs to the public clock dt-bindings
to move out of the previous maintenance scheme.

This refers to a discussion at [1] & [2] with Krzysztof about
the issue with the current maintenance.

It was decided to move every meson8b-clkc ID to the public clock
dt-bindings headers to be merged in a single tree so we
can safely add new clocks without having merge issues.

[1] https://lore.kernel.org/all/c088e01c-0714-82be-8347-6140daf56640@linaro.org/
[2] https://lore.kernel.org/all/2fabe721-7434-43e7-bae5-088a42ba128d@app.fastmail.com/

Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20230607-topic-amlogic-upstream-clkid-public-migration-v2-11-38172d17c27a@linaro.org
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>

dt-bindings: clk: g12a-aoclkc: expose all clock ids

Due to a policy change in clock ID bindings handling, expose
all the "private" clock IDs to the public clock dt-bindings
to move out of the previous maintenance scheme.

This refers to a discussion at [1] & [2] with Krzysztof about
the issue with the current maintenance.

It was decided to move every g12a-aoclkc ID to the public clock
dt-bindings headers to be merged in a single tree so we
can safely add new clocks without having merge issues.

[1] https://lore.kernel.org/all/c088e01c-0714-82be-8347-6140daf56640@linaro.org/
[2] https://lore.kernel.org/all/2fabe721-7434-43e7-bae5-088a42ba128d@app.fastmail.com/

Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20230607-topic-amlogic-upstream-clkid-public-migration-v2-10-38172d17c27a@linaro.org
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>

dt-bindings: clk: g12a-clks: expose all clock ids

Due to a policy change in clock ID bindings handling, expose
all the "private" clock IDs to the public clock dt-bindings
to move out of the previous maintenance scheme.

This refers to a discussion at [1] & [2] with Krzysztof about
the issue with the current maintenance.

It was decided to move every g12a-clkc ID to the public clock
dt-bindings headers to be merged in a single tree so we
can safely add new clocks without having merge issues.

[1] https://lore.kernel.org/all/c088e01c-0714-82be-8347-6140daf56640@linaro.org/
[2] https://lore.kernel.org/all/2fabe721-7434-43e7-bae5-088a42ba128d@app.fastmail.com/

Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20230607-topic-amlogic-upstream-clkid-public-migration-v2-9-38172d17c27a@linaro.org
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>

dt-bindings: clk: axg-clkc: expose all clock ids

Due to a policy change in clock ID bindings handling, expose
all the "private" clock IDs to the public clock dt-bindings
to move out of the previous maintenance scheme.

This refers to a discussion at [1] & [2] with Krzysztof about
the issue with the current maintenance.

It was decided to move every axg-clkc ID to the public clock
dt-bindings headers to be merged in a single tree so we
can safely add new clocks without having merge issues.

[1] https://lore.kernel.org/all/c088e01c-0714-82be-8347-6140daf56640@linaro.org/
[2] https://lore.kernel.org/all/2fabe721-7434-43e7-bae5-088a42ba128d@app.fastmail.com/

Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20230607-topic-amlogic-upstream-clkid-public-migration-v2-8-38172d17c27a@linaro.org
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>

dt-bindings: clk: gxbb-clkc: expose all clock ids

Due to a policy change in clock ID bindings handling, expose
all the "private" clock IDs to the public clock dt-bindings
to move out of the previous maintenance scheme.

This refers to a discussion at [1] & [2] with Krzysztof about
the issue with the current maintenance.

It was decided to move every gxbb-clkc ID to the public clock
dt-bindings headers to be merged in a single tree so we
can safely add new clocks without having merge issues.

[1] https://lore.kernel.org/all/c088e01c-0714-82be-8347-6140daf56640@linaro.org/
[2] https://lore.kernel.org/all/2fabe721-7434-43e7-bae5-088a42ba128d@app.fastmail.com/

Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20230607-topic-amlogic-upstream-clkid-public-migration-v2-7-38172d17c27a@linaro.org
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>

clk: meson: migrate axg-audio out of hw_onecell_data to drop NR_CLKS

The way hw_onecell_data is declared:
struct clk_hw_onecell_data {
unsigned int num;
struct clk_hw *hws[];
};

makes it impossible to have the clk_hw table declared outside while
using ARRAY_SIZE() to determine ".num" due to ".hws" being a flexible
array member.

Completely move out of hw_onecell_data and add a custom
devm_of_clk_add_hw_provider() "get" callback to retrieve the clk_hw
in order to finally get rid on the NR_CLKS define.

Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20230607-topic-amlogic-upstream-clkid-public-migration-v2-6-38172d17c27a@linaro.org
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>

clk: meson: migrate meson8b out of hw_onecell_data to drop NR_CLKS

The way hw_onecell_data is declared:
struct clk_hw_onecell_data {
unsigned int num;
struct clk_hw *hws[];
};

makes it impossible to have the clk_hw table declared outside while
using ARRAY_SIZE() to determine ".num" due to ".hws" being a flexible
array member.

Completely move out of hw_onecell_data and add a custom
devm_of_clk_add_hw_provider() "get" callback to retrieve the clk_hw
in order to finally get rid on the NR_CLKS define.

Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20230607-topic-amlogic-upstream-clkid-public-migration-v2-5-38172d17c27a@linaro.org
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>

clk: meson: migrate a1 clock drivers out of hw_onecell_data to drop NR_CLKS

The way hw_onecell_data is declared:
struct clk_hw_onecell_data {
unsigned int num;
struct clk_hw *hws[];
};

makes it impossible to have the clk_hw table declared outside while
using ARRAY_SIZE() to determine ".num" due to ".hws" being a flexible
array member.

Completely move out of hw_onecell_data and add a custom
devm_of_clk_add_hw_provider() "get" callback to retrieve the clk_hw
in order to finally get rid on the NR_CLKS define.

Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Dmitry Rokosov <ddrokosov@sberdevices.ru>
Link: https://lore.kernel.org/r/20230607-topic-amlogic-upstream-clkid-public-migration-v2-4-38172d17c27a@linaro.org
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>

clk: meson: migrate meson-aoclk out of hw_onecell_data to drop NR_CLKS

The way hw_onecell_data is declared:
  struct clk_hw_onecell_data {
          unsigned int num;
          struct clk_hw *hws[];
  };

makes it impossible to have the clk_hw table declared outside while
using ARRAY_SIZE() to determine ".num" due to ".hws" being a flexible
array member.

Completely move out of hw_onecell_data and add a custom
devm_of_clk_add_hw_provider() "get" callback to retrieve the clk_hw
from the meson_aoclk_data struct to finally get rid on the
NR_CLKS define.

[jbrunet: Fixed whitespace checkpatch warning]
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20230607-topic-amlogic-upstream-clkid-public-migration-v2-3-38172d17c27a@linaro.org
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>

clk: meson: migrate meson-eeclk out of hw_onecell_data to drop NR_CLKS

The way hw_onecell_data is declared:
      struct clk_hw_onecell_data {
              unsigned int num;
              struct clk_hw *hws[];
      };

makes it impossible to have the clk_hw table declared outside while
using ARRAY_SIZE() to determine ".num" due to ".hws" being a flexible
array member.

Completely move out of hw_onecell_data and add a custom
devm_of_clk_add_hw_provider() "get" callback to retrieve the clk_hw
from the meson_eeclkc_data struct to finally get rid on the
NR_CLKS define.

Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20230607-topic-amlogic-upstream-clkid-public-migration-v2-2-38172d17c27a@linaro.org
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>

clk: meson: introduce meson-clkc-utils

Let's introduce a new module called meson-clkc-utils that
will contain shared utility functions for all Amlogic clock
controller drivers.

The first utility function is a replacement of of_clk_hw_onecell_get
in order to get rid of the NR_CLKS define in all Amlogic clock
drivers.

The goal is to move all duplicate probe and init code in this module.

[jbrunet: Fixed MODULE_LICENCE checkpatch warning]
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20230607-topic-amlogic-upstream-clkid-public-migration-v2-1-38172d17c27a@linaro.org
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>

clk: ti: Replace kstrdup() + strreplace() with kstrdup_and_replace()

Replace open coded functionality of kstrdup_and_replace() with a call.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230804143910.15504-5-andriy.shevchenko@linux.intel.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>

clk: tegra: Replace kstrdup() + strreplace() with kstrdup_and_replace()

Replace open coded functionality of kstrdup_and_replace() with a call.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230804143910.15504-4-andriy.shevchenko@linux.intel.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>

driver core: Replace kstrdup() + strreplace() with kstrdup_and_replace()

Replace open coded functionality of kstrdup_and_replace() with a call.

Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230804143910.15504-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>

lib/string_helpers: Add kstrdup_and_replace() helper

Duplicate a NULL-terminated string and replace all occurrences of
the old character with a new one. In other words, provide functionality
of kstrdup() + strreplace().

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230804143910.15504-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>

dt-bindings: clock: versal: Convert the xlnx,zynqmp-clk.txt to yaml

Convert the xlnx,zynqmp-clk.txt to yaml.
versal-clk.yaml already exists that's why ZynqMP is converted and
merged.

Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@amd.com>
Link: https://lore.kernel.org/r/20230802043557.26478-1-shubhrajyoti.datta@amd.com
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>

dt-bindings: clock: xlnx,versal-clk: drop select:false

select:false makes the schema basically ignored and not effective, which
is clearly not what we want for a device binding.

Fixes: 352546805a44 ("dt-bindings: clock: Add bindings for versal clock driver")
Cc: <stable@vger.kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230728165923.108589-1-krzysztof.kozlowski@linaro.org
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Shubhrajyoti Datta <shubhrajyoti.datta@amd.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>

clk: versaclock3: Switch to use i2c_driver's probe callback

The previous mass switch of clk drivers done in commit 62279db5a323
("clk: Switch i2c drivers back to use .probe()") was based on v6.4-rc1
Since then this driver was added which needs to be converted back in the
same way before eventually .probe_new() can be dropped from struct
i2c_driver.

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230721071846.111663-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Stephen Boyd <sboyd@kernel.org>

clk: sunxi-ng: Modify mismatched function name

No functional modification involved.

drivers/clk/sunxi-ng/ccu_mmc_timing.c:54: warning: expecting prototype for sunxi_ccu_set_mmc_timing_mode(). Prototype was for sunxi_ccu_get_mmc_timing_mode() instead

Fixes: f6f64ed868d3 ("clk: sunxi-ng: Add interface to query or configure MMC timing modes.")
Signed-off-by: Zhang Jianhua <chris.zjh@huawei.com>
Reviewed-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://lore.kernel.org/r/20230722153107.2078179-1-chris.zjh@huawei.com
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>