Pali Rohár [Fri, 15 Jul 2022 08:13:12 +0000 (10:13 +0200)]
arm: mvebu: Avoid reading MVEBU_REG_PCIE_DEVID register too many times
Change detection of platform/cpu from runtime to compile time via config
define. This completely eliminates compiling code which is not going to run
on selected platform. Code which parses and prints device / revision id
still reads device id from MVEBU_REG_PCIE_DEVID register, but only once.
Signed-off-by: Pali Rohár <pali@kernel.org>
Acked-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Robert Marko [Fri, 3 Jun 2022 10:53:05 +0000 (12:53 +0200)]
mvebu: uDPU: disable non-present peripherals
uDPU like eDPU does not expose SCSI based peripherals like SATA nor PCI
and for sure it does not have the Intel E1000 PCI card.
So, like for eDPU remove those from the defconfig.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Reviewed-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Robert Marko [Fri, 3 Jun 2022 10:53:04 +0000 (12:53 +0200)]
mvebu: eDPU: disable SCSI support
eDPU does not use SCSI nor it has SATA exposed, and commit
arm: mvebu: a3720: Set BOOT_TARGET_DEVICES list to enabled peripherals
now allows compiling U-boot wihout all of the BOOT_TARGET_DEVICES since
not all boards have all of the listed peripherals exposed.
So, disable SCSI support in defconfig for eDPU.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Reviewed-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Marek Behún [Wed, 1 Jun 2022 15:17:06 +0000 (17:17 +0200)]
treewide: Fix Marek's name and change my e-mail address
Fix diacritics in some instances of my name and change my e-mail address
to kabel@kernel.org.
Add corresponding .mailmap entries.
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Marek Behún [Wed, 1 Jun 2022 15:17:05 +0000 (17:17 +0200)]
board: turris: Fix MAINTAINERS and add Pali
Fix MAINTAINERS files for Turris devices, add missing files and add Pali
as maintainer.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Pali Rohár [Mon, 30 May 2022 08:42:35 +0000 (10:42 +0200)]
tlv_eeprom: Add missing CRC32 dependency
tlv_eeprom uses crc32() function, so add dependency into Kconfig.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Stefan Roese <sr@denx.de>
Pali Rohár [Tue, 24 May 2022 08:58:42 +0000 (10:58 +0200)]
arch: mvebu: Disable by default unused peripherals in SPL
SPL on mvebu loads proper U-Boot from custom Marvell kwbimage format and
therefore support for other binary formats is not required to be present in
SPL. Boot source of proper U-Boot is defined by compile time options and
therefore it is not required to enable all possible and unused peripherals
in SPL by default.
This change decrease size of SPL binaries.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Pali Rohár [Mon, 23 May 2022 09:14:36 +0000 (11:14 +0200)]
arm: mvebu: a3720: Add NVMe to BOOT_TARGET_DEVICES list
Enable NVMe booting on boards which have enabled NVMe drivers.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Pali Rohár [Mon, 23 May 2022 09:14:35 +0000 (11:14 +0200)]
arm: mvebu: a3720: Set BOOT_TARGET_DEVICES list to enabled peripherals
This allows to compile U-Boot without some boot option for some A3720 board
which does not have that peripheral.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Robert Marko [Fri, 20 May 2022 11:46:33 +0000 (13:46 +0200)]
MAINTAINERS: add myself as Methode maintainer
I am currently maintaing the Methode uDPU and eDPU boards so add myself
as the maintainer for them.
Remove the old entry from board/Marvell/mvebu_armada-37xx/MAINTAINERS.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Reviewed-by: Stefan Roese <sr@denx.de>
Robert Marko [Fri, 20 May 2022 11:46:32 +0000 (13:46 +0200)]
arm: mvebu: add support for Methode eDPU
Methode eDPU is an Armada 3720 power board based on the Methode uDPU.
They feature the same CPU, RAM, and storage as well as the form factor.
However, eDPU only has one SFP slot plus a copper G.hn port which does not
work under U-boot.
In order to reduce duplication, split the uDPU DTS into a common one.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Reviewed-by: Stefan Roese <sr@denx.de>
Robert Marko [Fri, 20 May 2022 11:46:31 +0000 (13:46 +0200)]
arm: mvebu: dts: sync DTS
Update the uDPU DTS to the version that is pending upstream [1][2][3][4].
[1] https://patchwork.kernel.org/project/linux-arm-kernel/patch/
20220516124828.45144-4-robert.marko@sartura.hr/
[2] https://patchwork.kernel.org/project/linux-arm-kernel/patch/
20220516124828.45144-5-robert.marko@sartura.hr/
[3] https://patchwork.kernel.org/project/linux-arm-kernel/patch/
20220516124828.45144-6-robert.marko@sartura.hr/
[4] https://patchwork.kernel.org/project/linux-arm-kernel/patch/
20220516124828.45144-7-robert.marko@sartura.hr/
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Reviewed-by: Stefan Roese <sr@denx.de>
Chris Packham [Fri, 20 May 2022 04:39:22 +0000 (16:39 +1200)]
arm64: mvebu: handle non-zero base address for RAM
board_get_usable_ram_top() conflated the RAM size with the top address
of RAM. On systems where RAM starts at address 0 these numbers are the
same so it went unnoticed. Update board_get_usable_ram_top() to take
CONFIG_SYS_SDRAM_BASE into account when determining the top address.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Pali Rohár [Thu, 19 May 2022 09:11:52 +0000 (11:11 +0200)]
board: turris: Find atsha device by atsha driver
It does not matter what is DT node name of atsha device. So find it via
atsha driver and not by DT node name.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Tom Rini [Wed, 20 Jul 2022 11:38:49 +0000 (07:38 -0400)]
Merge tag 'for-v2022.10' of https://source.denx.de/u-boot/custodians/u-boot-ubi
ubifs changes for 2022.10
UBIFS fixes from Pali Rohar:
- ubifs: Fix ubifs_assert_cmt_locked
- ubifs: Use U-Boot assert() from <log.h>
Pali Rohár [Sun, 10 Jul 2022 11:38:07 +0000 (13:38 +0200)]
ubifs: Use U-Boot assert() from <log.h> in UBI/UBIFS code
U-Boot already provides assert function, so it use also in ubi and ubifs code.
Signed-off-by: Pali Rohár <pali@kernel.org>
Pali Rohár [Sun, 10 Jul 2022 11:38:06 +0000 (13:38 +0200)]
ubifs: Fix ubifs_assert_cmt_locked()
U-Boot does not implement down_write_trylock() and its stub always returns
true that lock was acquired. Therefore ubifs_assert_cmt_locked() assert
currently always fails.
Fix this issue by redefining ubifs_assert_cmt_locked() to just empty stub
as there is nothing to assert.
Signed-off-by: Pali Rohár <pali@kernel.org>
Tom Rini [Tue, 19 Jul 2022 19:54:57 +0000 (15:54 -0400)]
Merge https://source.denx.de/u-boot/custodians/u-boot-usb
Tom Rini [Tue, 19 Jul 2022 19:54:41 +0000 (15:54 -0400)]
Merge tag 'for-v2022.10' of https://source.denx.de/u-boot/custodians/u-boot-i2c
i2c changes for 2022.10
- new driver nuvoton, NPCM7xx from Jim Liu
Fixes:
- ast_i2c: Remove SCL direct drive mode
from Eddie James
- avoid dynamic stack use in dm_i2c_write
bloat-o-meter drivers/i2c/i2c-uclass.o.{0,1}
add/remove: 0/0 grow/shrink: 0/1 up/down: 0/-144 (-144)
Function old new delta
dm_i2c_write 552 408 -144
Total: Before=3828, After=3684, chg -3.76%
patch from Rasmus Villemoes
Tom Rini [Tue, 19 Jul 2022 14:52:15 +0000 (10:52 -0400)]
Merge https://source.denx.de/u-boot/custodians/u-boot-sunxi
To quote Andre:
One prominent feature is the restructering of the clock driver, which
allows to end up with one actual driver for all variants, although we
still only compile in support for one SoC.
Also contained are some initial SPI fixes, which should fix some
problems, and enable SPI flash support for the F1C100s SoC. Those
patches revealed more problems, I will queue fixes later on, but for
now it should at least still work.
Apart from some smaller fixes (for instance for NAND operation), there
is also preparation for the upcoming Allwinner D1 support, in form of
the USB PHY driver. There are more driver support patches to come.
The gitlab CI completed successfully, including the build test for all
160 sunxi boards. I also boot tested on a few boards, but didn't have
time for more elaborate tests this time.
Rasmus Villemoes [Thu, 7 Jul 2022 13:12:17 +0000 (15:12 +0200)]
i2c: avoid dynamic stack use in dm_i2c_write
The size of the dynamic stack allocation here is bounded by the if()
statement. However, just allocating the maximum size up-front and
doing malloc() if necessary avoids code duplication (the
i2c_setup_offset() until the invocation of ->xfer), and generates much
better (smaller) code:
bloat-o-meter drivers/i2c/i2c-uclass.o.{0,1}
add/remove: 0/0 grow/shrink: 0/1 up/down: 0/-144 (-144)
Function old new delta
dm_i2c_write 552 408 -144
Total: Before=3828, After=3684, chg -3.76%
It also makes static analysis of maximum stack usage (using the .su
files that are automatically generated during build) easier if there
are no lines saying "dynamic".
[This is not entirely equivalent to the existing code; this now uses
the stack for len <= 64 rather than len <= 63, but that seems like a
more natural limit.]
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Heiko Schocher <hs@denx.de>
Jim Liu [Thu, 23 Jun 2022 05:31:42 +0000 (13:31 +0800)]
i2c: nuvoton: Add NPCM7xx i2c driver
Add Nuvoton BMC NPCM750 i2c driver
Signed-off-by: Jim Liu <JJLIU0@nuvoton.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Eddie James [Wed, 11 May 2022 20:52:03 +0000 (15:52 -0500)]
i2c: ast_i2c: Remove SCL direct drive mode
SCL direct drive mode prevents communication with devices that
do clock stretching, so disable. The Linux driver doesn't use
this mode, and the engine can handle clock stretching.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: ryan_chen <ryan_chen@aspeedtech.com>
Samuel Holland [Fri, 15 Jul 2022 04:09:22 +0000 (23:09 -0500)]
phy: sun4i-usb: Add D1 variant
D1 has a register layout like A100 and H616, with the moved SIDDQ bit.
Unlike H616 it does not have any dependencies between PHY instances.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Andre Przywara [Fri, 15 Jul 2022 04:09:21 +0000 (23:09 -0500)]
phy: sun4i-usb: Rework HCI PHY (aka "pmu_unk1") handling
As Icenowy pointed out, newer manuals (starting with H6) actually
document the register block at offset 0x800 as "HCI controller and PHY
interface", also describe the bits in our "PMU_UNK1" register.
Let's put proper names to those "unknown" variables and symbols.
While we are at it, generalise the existing code by allowing a bitmap
of bits to clear and set, to cover newer SoCs: The A100 and H616 use a
different bit for the SIDDQ control.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Samuel Holland [Fri, 15 Jul 2022 04:09:20 +0000 (23:09 -0500)]
phy: sun4i-usb: Drop use of arch-specific headers
Since commit
089ffd0aedb7 ("phy: sun4i-usb: Use CLK and RESET support")
neither of these headers is used. Dropping them allows the driver to be
architecture-independent.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Samuel Holland [Fri, 15 Jul 2022 04:09:19 +0000 (23:09 -0500)]
sunxi: Move INITIAL_USB_SCAN_DELAY to driver Kconfig
This option is used only by the phy-sun4i-usb driver, which does not
inherently depend on the ARM architecture.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tom Rini [Mon, 18 Jul 2022 19:37:38 +0000 (15:37 -0400)]
Merge branch 'master' of https://source.denx.de/u-boot/custodians/u-boot-spi
- add Macronix Octal flash (JaimeLiao)
Jae Hyun Yoo [Fri, 8 Jul 2022 19:03:19 +0000 (12:03 -0700)]
mtd: spi-nor-ids: add winbond w25q512nw family support
Add Winbond w25q512nwq/n and w25q512nwm support.
datasheet:
https://www.winbond.com/resource-files/W25Q512NW%20RevB%
2007192021.pdf
Signed-off-by: Jae Hyun Yoo <quic_jaehyoo@quicinc.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
JaimeLiao [Mon, 18 Jul 2022 06:49:22 +0000 (14:49 +0800)]
mtd: spi-nor-core: Add support for Macronix Octal flash
Adding Macronix Octal flash for Octal DTR support.
The octaflash series can be divided into the following types:
MX25 series : Serial NOR Flash.
MX66 series : Serial NOR Flash with stacked die.(Size larger than 1Gb)
LM/UM series : Up to 250MHz clock frequency with both DTR/STR operation.
LW/UW series : Support simultaneous Read-while-Write operation in multiple
bank architecture. Read-while-write feature which means read
data one bank while another bank is programing or erasing.
MX25LM : 3.0V Octal I/O
-https://www.mxic.com.tw/Lists/Datasheet/Attachments/7841/MX25LM51245G,%203V,%20512Mb,%20v1.1.pdf
MX25UM : 1.8V Octal I/O
-https://www.mxic.com.tw/Lists/Datasheet/Attachments/7525/MX25UM51245G%20Extreme%20Speed,%201.8V,%20512Mb,%20v1.0.pdf
MX66LM : 3.0V Octal I/O with stacked die
-https://www.mxic.com.tw/Lists/Datasheet/Attachments/7929/MX66LM1G45G,%203V,%201Gb,%20v1.1.pdf
MX66UM : 1.8V Octal I/O with stacked die
-https://www.mxic.com.tw/Lists/Datasheet/Attachments/7721/MX66UM1G45G,%201.8V,%201Gb,%20v1.1.pdf
MX25LW : 3.0V Octal I/O with Read-while-Write
MX25UW : 1.8V Octal I/O with Read-while-Write
MX66LW : 3.0V Octal I/O with Read-while-Write and stack die
MX66UW : 1.8V Octal I/O with Read-while-Write and stack die
About LW/UW series, please contact us freely if you have any
questions. For adding Octal NOR Flash IDs, we have validated
each Flash on plateform zynq-picozed.
As below are the SFDP table dump.
zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/jedec_id
c2943c
zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/manufacturer
macronix
zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/partname
mx66uw2g345gx0
zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/sfdp > mx66uw2g345gx0
zynq> hexdump mx66uw2g345gx0
0000000 4653 5044 0108 fd04 0700 1401 0040 ff00
0000010 0187 1c01 0090 ff00 000a 0801 0100 ff00
0000020 0005 0501 0120 ff00 0084 0201 0134 ff00
0000030 0000 0000 0000 0000 ffff ffff ffff ffff
0000040 20e5 ff8a ffff 7fff ff00 ff00 ff00 ff00
0000050 ffee ffff ffff ff00 ffff ff00 200c d810
0000060 ff00 ff00 7987 0001 1284 e200 04cc 4667
0000070 b030 b030 bdf4 5cd5 0000 ff00 1010 2000
0000080 0000 0000 0000 237c 0048 0000 0000 8888
0000090 0000 0000 0000 4000 d10f f3ff d10f f3ff
00000a0 0500 9000 0500 b100 2b00 9500 2b00 9600
00000b0 7172 b803 7172 b803 0000 0000 a390 8218
00000c0 c000 9669 0000 0000 0000 0000 7172 9800
00000d0 7172 b800 7172 9900 0000 0000 7172 9800
00000e0 7172 f800 7172 9900 7172 f900 0000 0000
00000f0 0000 0000 1501 d001 7172 d806 0000 5086
0000100 0000 0106 0000 0000 0002 0301 0200 0000
0000110 0000 0106 0000 0000 0000 0672 0200 0000
0000120 ee00 69c0 7272 7171 d800 f6f7 0a00 0000
0000130 4514 8098 0643 001f dc21 ffff ffff ffff
0000140 ffff ffff ffff ffff ffff ffff ffff ffff
zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/jedec_id
c2853b
zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/manufacturer
macronix
zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/partname
mx66lm1g45g
zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/sfdp > mx66lm1g45g
zynq> hexdump mx66lm1g45g
0000000 4653 5044 0108 fd04 0700 1401 0040 ff00
0000010 0187 1c01 0090 ff00 000a 0801 0100 ff00
0000020 0005 0501 0120 ff00 0084 0201 0134 ff00
0000030 0000 0000 0000 0000 ffff ffff ffff ffff
0000040 20e5 ff8a ffff 3fff ff00 ff00 ff00 ff00
0000050 ffee ffff ffff ff00 ffff ff00 200c d810
0000060 ff00 ff00 6987 0001 1282 e200 02cc 3867
0000070 b030 b030 bdf4 5cd5 0000 ff00 1010 2000
0000080 0000 0000 0000 a37c 0048 0000 0000 6666
0000090 0000 0000 0000 4000 d10f f3ff d10f f3ff
00000a0 0500 9000 0500 b100 2b00 9500 2b00 9600
00000b0 7172 b803 7172 b803 0000 0000 a390 8218
00000c0 c000 9669 0000 0000 0000 0000 7172 9800
00000d0 7172 b800 7172 9900 0000 0000 7172 9800
00000e0 7172 f800 7172 9900 7172 f900 0000 0000
00000f0 0000 0000 1501 d001 7172 d806 0000 5086
0000100 0000 0106 0000 0000 0002 0301 0200 0000
0000110 0000 0106 0000 0000 0000 0672 0200 0000
0000120 ee00 69c0 7272 7171 d800 f6f7 0000 0000
0000130 3514 001c 0643 000f dc21 ffff ffff ffff
0000140 ffff ffff ffff ffff ffff ffff ffff ffff
zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/jedec_id
c2853a
zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/manufacturer
macronix
zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/partname
mx25lm51245g
zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/sfdp > mx25lm51245g
zynq> hexdump mx25lm51245g
0000000 4653 5044 0108 fd04 0700 1401 0040 ff00
0000010 0187 1c01 0090 ff00 000a 0801 0100 ff00
0000020 0005 0501 0120 ff00 0084 0201 0134 ff00
0000030 0000 0000 0000 0000 ffff ffff ffff ffff
0000040 20e5 ff8a ffff 1fff ff00 ff00 ff00 ff00
0000050 ffee ffff ffff ff00 ffff ff00 200c d810
0000060 ff00 ff00 7989 0001 128d e200 02cc 4467
0000070 b030 b030 bdf4 5cd5 0000 ff00 1010 2000
0000080 0000 0000 0000 a37c 0048 0000 0000 6666
0000090 0000 0000 0000 4000 d10f f3ff d10f f3ff
00000a0 0500 9000 0500 b100 2b00 9500 2b00 9600
00000b0 7172 b803 7172 b803 0000 0000 a390 8218
00000c0 c000 9669 0000 0000 0000 0000 7172 9800
00000d0 7172 b800 7172 9900 0000 0000 7172 9800
00000e0 7172 f800 7172 9900 7172 f900 0000 0000
00000f0 0000 0000 1501 d001 7172 d806 0000 5086
0000100 0000 0106 0000 0000 0002 0301 0200 0000
0000110 0000 0106 0000 0000 0000 0672 0200 0000
0000120 ee00 69c0 7272 7171 d800 f6f7 0000 0000
0000130 3514 001c 0643 000f dc21 ffff ffff ffff
0000140 ffff ffff ffff ffff ffff ffff ffff ffff
zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/jedec_id
c2863a
zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/manufacturer
macronix
zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/partname
mx25lw51245g
zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/sfdp > mx25lw51245g
zynq> hexdump mx25lw51245g
0000000 4653 5044 0108 fd04 0700 1401 0040 ff00
0000010 0187 1c01 0090 ff00 000a 0801 0100 ff00
0000020 0005 0501 0120 ff00 0084 0201 0134 ff00
0000030 0000 0000 0000 0000 0000 0000 0000 0000
0000040 20e5 ff8a ffff 1fff ff00 ff00 ff00 ff00
0000050 ffee ffff ffff ff00 ffff ff00 200c d810
0000060 ff00 ff00 798b 0001 128f e200 04cc 4667
0000070 b030 b030 bdf4 5cd5 0000 ff00 1010 2000
0000080 0000 0000 0000 a37c 0048 0000 0000 6666
0000090 0000 0000 0000 4000 d10f f3ff d10f f3ff
00000a0 0500 9000 0500 b100 2b00 9500 2b00 9600
00000b0 7172 b803 7172 b803 0000 0000 a390 8218
00000c0 c000 9669 0000 0000 0000 0000 7172 9800
00000d0 7172 b800 7172 9900 0000 0000 7172 9800
00000e0 7172 f800 7172 9900 7172 f900 0000 0000
00000f0 0000 0000 1501 d001 7172 d806 0000 5086
0000100 0000 0106 0000 0000 0002 0301 0200 0000
0000110 0000 0106 0000 0000 0000 0672 0200 0000
0000120 ee00 69c0 7272 7171 d800 f6f7 0000 0000
0000130 3514 001c 0643 000f dc21 ffff ffff ffff
0000140 ffff ffff ffff ffff ffff ffff ffff ffff
zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/jedec_id
c28539
zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/manufacturer
macronix
zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/partname
mx25lm25645g
zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/sfdp > mx25lm25645g
zynq> hexdump mx25lm25645g
0000000 4653 5044 0108 fd04 0700 1401 0040 ff00
0000010 0187 1c01 0090 ff00 000a 0801 0100 ff00
0000020 0005 0501 0120 ff00 0084 0201 0134 ff00
0000030 0000 0000 0000 0000 ffff ffff ffff ffff
0000040 20e5 ff8a ffff 0fff ff00 ff00 ff00 ff00
0000050 ffee ffff ffff ff00 ffff ff00 200c d810
0000060 ff00 ff00 6987 0001 1282 d200 02cc 3867
0000070 b030 b030 bdf4 5cd5 0000 ff00 1010 2000
0000080 0000 0000 0000 a37c 0048 0000 0000 6666
0000090 0000 0000 0000 4000 d10f f3ff d10f f3ff
00000a0 0500 9000 0500 b100 2b00 9500 2b00 9600
00000b0 7172 b803 7172 b803 0000 0000 a390 8218
00000c0 c000 9669 0000 0000 0000 0000 7172 9800
00000d0 7172 b800 7172 9900 0000 0000 7172 9800
00000e0 7172 f800 7172 9900 7172 f900 0000 0000
00000f0 0000 0000 1501 d001 7172 d806 0000 5086
0000100 0000 0106 0000 0000 0002 0301 0200 0000
0000110 0000 0106 0000 0000 0000 0672 0200 0000
0000120 ee00 69c0 7272 7171 d800 f6f7 0000 0000
0000130 3514 001c 0643 000f dc21 ffff ffff ffff
0000140 ffff ffff ffff ffff ffff ffff ffff ffff
zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/jedec_id
c2843c
zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/manufacturer
macronix
zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/partname
mx66uw2g345g
zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/sfdp > mx66uw2g345g
zynq> hexdump mx66uw2g345g
0000000 4653 5044 0108 fd04 0700 1401 0040 ff00
0000010 0187 1c01 0090 ff00 000a 0801 0100 ff00
0000020 0005 0501 0120 ff00 0084 0201 0134 ff00
0000030 0000 0000 0000 0000 ffff ffff ffff ffff
0000040 20e5 ff8a ffff 7fff ff00 ff00 ff00 ff00
0000050 ffee ffff ffff ff00 ffff ff00 200c d810
0000060 ff00 ff00 7987 0001 1284 e200 04cc 4667
0000070 b030 b030 bdf4 5cd5 0000 ff00 1010 2000
0000080 0000 0000 0000 237c 0048 0000 0000 8888
0000090 0000 0000 0000 4000 d10f f3ff d10f f3ff
00000a0 0500 9000 0500 b100 2b00 9500 2b00 9600
00000b0 7172 b803 7172 b803 0000 0000 a390 8218
00000c0 c000 9669 0000 0000 0000 0000 7172 9800
00000d0 7172 b800 7172 9900 0000 0000 7172 9800
00000e0 7172 f800 7172 9900 7172 f900 0000 0000
00000f0 0000 0000 1501 d001 7172 d806 0000 5086
0000100 0000 0106 0000 0000 0002 0301 0200 0000
0000110 0000 0106 0000 0000 0000 0672 0200 0000
0000120 ee00 69c0 7272 7171 d800 f6f7 0a00 0000
0000130 4514 8098 0643 001f dc21 ffff ffff ffff
0000140 ffff ffff ffff ffff ffff ffff ffff ffff
zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/jedec_id
c2803b
zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/manufacturer
macronix
zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/partname
mx66um1g45g
zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/sfdp > mx66um1g45g
zynq> hexdump mx66um1g45g
0000000 4653 5044 0108 fd04 0700 1401 0040 ff00
0000010 0187 1c01 0090 ff00 000a 0801 0100 ff00
0000020 0005 0501 0120 ff00 0084 0201 0134 ff00
0000030 0000 0000 0000 0000 ffff ffff ffff ffff
0000040 20e5 ff8a ffff 3fff ff00 ff00 ff00 ff00
0000050 ffee ffff ffff ff00 ffff ff00 200c d810
0000060 ff00 ff00 7989 0001 128d e200 02cc 4467
0000070 b030 b030 bdf4 5cd5 0000 ff00 1010 2000
0000080 0000 0000 0000 a37c 0048 0000 0000 8888
0000090 0000 0000 0000 4000 d10f f3ff d10f f3ff
00000a0 0500 9000 0500 b100 2b00 9500 2b00 9600
00000b0 7172 b803 7172 b803 0000 0000 a390 8218
00000c0 c000 9669 0000 0000 0000 0000 7172 9800
00000d0 7172 b800 7172 9900 0000 0000 7172 9800
00000e0 7172 f800 7172 9900 7172 f900 0000 0000
00000f0 0000 0000 1501 d001 7172 d806 0000 5086
0000100 0000 0106 0000 0000 0002 0301 0200 0000
0000110 0000 0106 0000 0000 0000 0672 0200 0000
0000120 ee00 69c0 7272 7171 d800 f6f7 0a00 0000
0000130 3514 809c 0643 000f dc21 ffff ffff ffff
0000140 ffff ffff ffff ffff ffff ffff ffff ffff
zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/jedec_id
c2813b
zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/manufacturer
macronix
zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/partname
mx66uw1g45g
zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/sfdp > mx66uw1g45g
zynq> hexdump mx66uw1g45g
0000000 4653 5044 0108 fd04 0700 1401 0040 ff00
0000010 0187 1c01 0090 ff00 000a 0801 0100 ff00
0000020 0005 0501 0120 ff00 0084 0201 0134 ff00
0000030 0000 0000 0000 0000 ffff ffff ffff ffff
0000040 20e5 ff8a ffff 3fff ff00 ff00 ff00 ff00
0000050 ffee ffff ffff ff00 ffff ff00 200c d810
0000060 ff00 ff00 798b 0001 128f e200 04cc 4667
0000070 b030 b030 bdf4 5cd5 0000 ff00 1010 2000
0000080 0000 0000 0000 a37c 0048 0000 0000 8888
0000090 0000 0000 0000 4000 d10f f3ff d10f f3ff
00000a0 0500 9000 0500 b100 2b00 9500 2b00 9600
00000b0 7172 b803 7172 b803 0000 0000 a390 8218
00000c0 c000 9669 0000 0000 0000 0000 7172 9800
00000d0 7172 b800 7172 9900 0000 0000 7172 9800
00000e0 7172 f800 7172 9900 7172 f900 0000 0000
00000f0 0000 0000 1501 d001 7172 d806 0000 5086
0000100 0000 0106 0000 0000 0002 0301 0200 0000
0000110 0000 0106 0000 0000 0000 0672 0200 0000
0000120 ee00 69c0 7272 7171 d800 f6f7 0a00 0000
0000130 4514 8098 0643 000f dc21 ffff ffff ffff
0000140 ffff ffff ffff ffff ffff ffff ffff ffff
zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/jedec_id
c2813a
zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/manufacturer
macronix
zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/partname
mx25uw51245g
zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/sfdp > mx25uw51245g
zynq> hexdump mx25uw51245g
0000000 4653 5044 0108 fd04 0700 1401 0040 ff00
0000010 0187 1c01 0090 ff00 000a 0801 0100 ff00
0000020 0005 0501 0120 ff00 0084 0201 0134 ff00
0000030 0000 0000 0000 0000 ffff ffff ffff ffff
0000040 20e5 ff8a ffff 1fff ff00 ff00 ff00 ff00
0000050 ffee ffff ffff ff00 ffff ff00 200c d810
0000060 ff00 ff00 798b 0001 128f e200 04cc 4667
0000070 b030 b030 bdf4 5cd5 0000 ff00 1010 2000
0000080 0000 0000 0000 a37c 0048 0000 0000 7777
0000090 0000 0000 0000 4000 d10f f3ff d10f f3ff
00000a0 0500 9000 0500 b100 2b00 9500 2b00 9600
00000b0 7172 b803 7172 b803 0000 0000 a390 8218
00000c0 c000 9669 0000 0000 0000 0000 7172 9800
00000d0 7172 b800 7172 9900 0000 0000 7172 9800
00000e0 7172 f800 7172 9900 7172 f900 0000 0000
00000f0 0000 0000 1501 d001 7172 d806 0000 5086
0000100 0000 0106 0000 0000 0002 0301 0200 0000
0000110 0000 0106 0000 0000 0000 0672 0200 0000
0000120 ee00 69c0 7272 7171 d800 f6f7 0000 0000
0000130 4514 8098 0643 000f dc21 ffff ffff ffff
0000140 ffff ffff ffff ffff ffff ffff ffff ffff
zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/jedec_id
c2843a
zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/manufacturer
macronix
zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/partname
mx25uw51345g
zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/sfdp > mx25uw51345g
zynq> hexdump mx25uw51345g
0000000 4653 5044 0108 fd04 0700 1401 0040 ff00
0000010 0187 1c01 0090 ff00 000a 0801 0100 ff00
0000020 0005 0501 0120 ff00 0084 0201 0134 ff00
0000030 0000 0000 0000 0000 ffff ffff ffff ffff
0000040 20e5 ff8a ffff 1fff ff00 ff00 ff00 ff00
0000050 ffee ffff ffff ff00 ffff ff00 200c d810
0000060 ff00 ff00 798b 0001 128f e200 04cc 4667
0000070 b030 b030 bdf4 5cd5 0000 ff00 1010 2000
0000080 0000 0000 0000 237c 0048 0000 0000 8888
0000090 0000 0000 0000 4000 d10f f3ff d10f f3ff
00000a0 0500 9000 0500 b100 2b00 9500 2b00 9600
00000b0 7172 b803 7172 b803 0000 0000 a390 8218
00000c0 c000 9669 0000 0000 0000 0000 7172 9800
00000d0 7172 b800 7172 9900 0000 0000 7172 9800
00000e0 7172 f800 7172 9900 7172 f900 0000 0000
00000f0 0000 0000 1501 d001 7172 d806 0000 5086
0000100 0000 0106 0000 0000 0002 0301 0200 0000
0000110 0000 0106 0000 0000 0000 0672 0200 0000
0000120 ee00 69c0 7272 7171 d800 f6f7 0a00 0000
0000130 4514 8098 0643 000f dc21 ffff ffff ffff
0000140 ffff ffff ffff ffff ffff ffff ffff ffff
zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/jedec_id
c28039
zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/manufacturer
macronix
zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/partname
mx25um25645g
zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/sfdp > mx25um25645g
zynq> random: fast init done
zynq> hexdump mx25um25645g
0000000 4653 5044 0108 fd04 0700 1401 0040 ff00
0000010 0187 1c01 0090 ff00 000a 0801 0100 ff00
0000020 0005 0501 0120 ff00 0084 0201 0134 ff00
0000030 0000 0000 0000 0000 ffff ffff ffff ffff
0000040 20e5 ff8a ffff 0fff ff00 ff00 ff00 ff00
0000050 ffee ffff ffff ff00 ffff ff00 200c d810
0000060 ff00 ff00 7987 0001 1284 d200 02cc 3867
0000070 b030 b030 bdf4 5cd5 0000 ff00 1010 2000
0000080 0000 0000 0000 a37c 0048 0000 0000 8888
0000090 0000 0000 0000 4000 d10f f3ff d10f f3ff
00000a0 0500 9000 0500 b100 2b00 9500 2b00 9600
00000b0 7172 b803 7172 b803 0000 0000 a390 8218
00000c0 c000 9669 0000 0000 0000 0000 7172 9800
00000d0 7172 b800 7172 9900 0000 0000 7172 9800
00000e0 7172 f800 7172 9900 7172 f900 0000 0000
00000f0 0000 0000 1501 d001 7172 d806 0000 5086
0000100 0000 0106 0000 0000 0002 0301 0200 0000
0000110 0000 0106 0000 0000 0000 0672 0200 0000
0000120 ee00 69c0 7272 7171 d800 f6f7 0a00 0000
0000130 3514 809c 0643 000f dc21 ffff ffff ffff
0000140 ffff ffff ffff ffff ffff ffff ffff ffff
zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/jedec_id
c28139
zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/manufacturer
macronix
zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/partname
mx25uw25645g
zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/sfdp > mx25uw25645g
zynq> hexdump mx25uw25645g
0000000 4653 5044 0108 fd04 0700 1401 0040 ff00
0000010 0187 1c01 0090 ff00 000a 0801 0100 ff00
0000020 0005 0501 0120 ff00 0084 0201 0134 ff00
0000030 0000 0000 0000 0000 ffff ffff ffff ffff
0000040 20e5 ff8a ffff 0fff ff00 ff00 ff00 ff00
0000050 ffee ffff ffff ff00 ffff ff00 200c d810
0000060 ff00 ff00 7989 0001 128d d200 04cc 4667
0000070 b030 b030 bdf4 5cd5 0000 ff00 1010 2000
0000080 0000 0000 0000 a37c 0048 0000 0000 8888
0000090 0000 0000 0000 4000 d10f f3ff d10f f3ff
00000a0 0500 9000 0500 b100 2b00 9500 2b00 9600
00000b0 7172 b803 7172 b803 0000 0000 a390 8218
00000c0 c000 9669 0000 0000 0000 0000 7172 9800
00000d0 7172 b800 7172 9900 0000 0000 7172 9800
00000e0 7172 f800 7172 9900 7172 f900 0000 0000
00000f0 0000 0000 1501 d001 7172 d806 0000 5086
0000100 0000 0106 0000 0000 0002 0301 0200 0000
0000110 0000 0106 0000 0000 0000 0672 0200 0000
0000120 ee00 69c0 7272 7171 d800 f6f7 0a00 0000
0000130 4514 8098 0643 000f dc21 ffff ffff ffff
0000140 ffff ffff ffff ffff ffff ffff ffff ffff
zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/jedec_id
c28339
zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/manufacturer
macronix
zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/partname
mx25um25345g
zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/sfdp > mx25um25345g
zynq> hexdump mx25um25345g
0000000 4653 5044 0108 fd04 0700 1401 0040 ff00
0000010 0187 1c01 0090 ff00 000a 0801 0100 ff00
0000020 0005 0501 0120 ff00 0084 0201 0134 ff00
0000030 0000 0000 0000 0000 ffff ffff ffff ffff
0000040 20e5 ff8a ffff 0fff ff00 ff00 ff00 ff00
0000050 ffee ffff ffff ff00 ffff ff00 200c d810
0000060 ff00 ff00 6987 0001 1282 d200 02cc 3867
0000070 b030 b030 bdf4 5cd5 0000 ff00 1010 2000
0000080 0000 0000 0000 237c 0048 0000 0000 8888
0000090 0000 0000 0000 4000 d10f f3ff d10f f3ff
00000a0 0500 9000 0500 b100 2b00 9500 2b00 9600
00000b0 7172 b803 7172 b803 0000 0000 a390 8218
00000c0 c000 9669 0000 0000 0000 0000 7172 9800
00000d0 7172 b800 7172 9900 0000 0000 7172 9800
00000e0 7172 f800 7172 9900 7172 f900 0000 0000
00000f0 0000 0000 1501 d001 7172 d806 0000 5086
0000100 0000 0106 0000 0000 0002 0301 0200 0000
0000110 0000 0106 0000 0000 0000 0672 0200 0000
0000120 ee00 69c0 7272 7171 d800 f6f7 0904 0000
0000130 4514 8098 0643 000f dc21 ffff ffff ffff
0000140 ffff ffff ffff ffff ffff ffff ffff ffff
zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/jedec_id
c28439
zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/manufacturer
macronix
zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/partname
mx25uw25345g
zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/sfdp > mx25uw25345g
zynq> hexdump mx25uw25345g
0000000 4653 5044 0108 fd04 0700 1401 0040 ff00
0000010 0187 1c01 0090 ff00 000a 0801 0100 ff00
0000020 0005 0501 0120 ff00 0084 0201 0134 ff00
0000030 0000 0000 0000 0000 ffff ffff ffff ffff
0000040 20e5 ff8a ffff 0fff ff00 ff00 ff00 ff00
0000050 ffee ffff ffff ff00 ffff ff00 200c d810
0000060 ff00 ff00 7987 0001 1284 d200 04cc 4667
0000070 b030 b030 bdf4 5cd5 0000 ff00 1010 2000
0000080 0000 0000 0000 237c 0048 0000 0000 8888
0000090 0000 0000 0000 4000 d10f f3ff d10f f3ff
00000a0 0500 9000 0500 b100 2b00 9500 2b00 9600
00000b0 7172 b803 7172 b803 0000 0000 a390 8218
00000c0 c000 9669 0000 0000 0000 0000 7172 9800
00000d0 7172 b800 7172 9900 0000 0000 7172 9800
00000e0 7172 f800 7172 9900 7172 f900 0000 0000
00000f0 0000 0000 1501 d001 7172 d806 0000 5086
0000100 0000 0106 0000 0000 0002 0301 0200 0000
0000110 0000 0106 0000 0000 0000 0672 0200 0000
0000120 ee00 69c0 7272 7171 d800 f6f7 0a00 0000
0000130 4514 8098 0643 000f dc21 ffff ffff ffff
0000140 ffff ffff ffff ffff ffff ffff ffff ffff
zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/jedec_id
c28138
zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/manufacturer
macronix
zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/partname
mx25uw12845g
zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/sfdp > mx25uw12845g
zynq> hexdump mx25uw12845g
0000000 4653 5044 0108 fd04 0700 1401 0040 ff00
0000010 0187 1c01 0090 ff00 000a 0801 0100 ff00
0000020 0005 0501 0120 ff00 0084 0201 0134 ff00
0000030 0000 0000 0000 0000 0000 0000 0000 0000
0000040 20e5 ff8a ffff 07ff ff00 ff00 ff00 ff00
0000050 ffee ffff ffff ff00 ffff ff00 200c d810
0000060 ff00 ff00 798b 0001 128f c900 04cc 4667
0000070 b030 b030 bdf4 5cd5 0000 ff00 1010 2000
0000080 0000 0000 0000 a37c 0048 0000 0000 8888
0000090 0000 0000 0000 4000 d10f f3ff d10f f3ff
00000a0 0500 9000 0500 b100 2b00 9500 2b00 9600
00000b0 7172 b803 7172 b803 0000 0000 a390 8218
00000c0 c000 9669 0000 0000 0000 0000 7172 9800
00000d0 7172 b800 7172 9900 0000 0000 7172 9800
00000e0 7172 f800 7172 9900 7172 f900 0000 0000
00000f0 0000 0000 1501 d001 7172 d806 0000 5086
0000100 0000 0106 0000 0000 0002 0301 0200 0000
0000110 0000 0106 0000 0000 0000 0672 0200 0000
0000120 ee00 69c0 7272 7171 d800 f6f7 0a00 0000
0000130 4514 8098 0643 000f dc21 ffff ffff ffff
0000140 ffff ffff ffff ffff ffff ffff ffff ffff
zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/jedec_id
c28438
zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/manufacturer
macronix
zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/partname
mx25uw12345g
zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/sfdp > mx25uw12345g
zynq> hexdump mx25uw12345g
0000000 4653 5044 0108 fd04 0700 1401 0040 ff00
0000010 0187 1c01 0090 ff00 000a 0801 0100 ff00
0000020 0005 0501 0120 ff00 0084 0201 0134 ff00
0000030 0000 0000 0000 0000 ffff ffff ffff ffff
0000040 20e5 ff8a ffff 07ff ff00 ff00 ff00 ff00
0000050 ffee ffff ffff ff00 ffff ff00 200c d810
0000060 ff00 ff00 798b 0001 128f c900 04cc 4667
0000070 b030 b030 bdf4 5cd5 0000 ff00 1010 2000
0000080 0000 0000 0000 237c 0048 0000 0000 8888
0000090 0000 0000 0000 4000 d10f f3ff d10f f3ff
00000a0 0500 9000 0500 b100 2b00 9500 2b00 9600
00000b0 7172 b803 7172 b803 0000 0000 a390 8218
00000c0 c000 9669 0000 0000 0000 0000 7172 9800
00000d0 7172 b800 7172 9900 0000 0000 7172 9800
00000e0 7172 f800 7172 9900 7172 f900 0000 0000
00000f0 0000 0000 1501 d001 7172 d806 0000 5086
0000100 0000 0106 0000 0000 0002 0301 0200 0000
0000110 0000 0106 0000 0000 0000 0672 0200 0000
0000120 ee00 69c0 7272 7171 d800 f6f7 0a00 0000
0000130 4514 8098 0643 000f dc21 ffff ffff ffff
0000140 ffff ffff ffff ffff ffff ffff ffff ffff
zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/jedec_id
c28137
zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/manufacturer
macronix
zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/partname
mx25uw6445g
zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/sfdp > mx25uw6445g
zynq> hexdump mx25uw6445g
0000000 4653 5044 0108 fd04 0700 1401 0040 ff00
0000010 0187 1c01 0090 ff00 000a 0801 0100 ff00
0000020 0005 0501 0120 ff00 0084 0201 0134 ff00
0000030 0000 0000 0000 0000 ffff ffff ffff ffff
0000040 20e5 ff8a ffff 03ff ff00 ff00 ff00 ff00
0000050 ffee ffff ffff ff00 ffff ff00 200c d810
0000060 ff00 ff00 7989 0001 128d c400 04cc 4667
0000070 b030 b030 bdf4 5cd5 0000 ff00 1010 2000
0000080 0000 0000 0000 a37c 0048 0000 0000 8888
0000090 0000 0000 0000 4000 d10f f3ff d10f f3ff
00000a0 0500 9000 0500 b100 2b00 9500 2b00 9600
00000b0 7172 b803 7172 b803 0000 0000 a390 8218
00000c0 c000 9669 0000 0000 0000 0000 7172 9800
00000d0 7172 b800 7172 9900 0000 0000 7172 9800
00000e0 7172 f800 7172 9900 7172 f900 0000 0000
00000f0 0000 0000 1501 d001 7172 d806 0000 5086
0000100 0000 0106 0000 0000 0002 0301 0200 0000
0000110 0000 0106 0000 0000 0000 0672 0200 0000
0000120 ee00 69c0 7272 7171 d800 f6f7 0a00 0000
0000130 4514 8098 0643 000f dc21 ffff ffff ffff
0000140 ffff ffff ffff ffff ffff ffff ffff ffff
zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/jedec_id
c28437
zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/manufacturer
macronix
zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/partname
mx25uw6345g
zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/sfdp > mx25uw6345g
zynq> hexdump mx25uw6345g
0000000 4653 5044 0108 fd04 0700 1401 0040 ff00
0000010 0187 1c01 0090 ff00 000a 0801 0100 ff00
0000020 0005 0501 0120 ff00 0084 0201 0134 ff00
0000030 0000 0000 0000 0000 ffff ffff ffff ffff
0000040 20e5 ff8a ffff 03ff ff00 ff00 ff00 ff00
0000050 ffee ffff ffff ff00 ffff ff00 200c d810
0000060 ff00 ff00 798b 0001 128f c400 04cc 4667
0000070 b030 b030 bdf4 5cd5 0000 ff00 1010 2000
0000080 0000 0000 0000 237c 0048 0000 0000 8888
0000090 0000 0000 0000 4000 d10f f3ff d10f f3ff
00000a0 0500 9000 0500 b100 2b00 9500 2b00 9600
00000b0 7172 b803 7172 b803 0000 0000 a390 8218
00000c0 c000 9669 0000 0000 0000 0000 7172 9800
00000d0 7172 b800 7172 9900 0000 0000 7172 9800
00000e0 7172 f800 7172 9900 7172 f900 0000 0000
00000f0 0000 0000 1501 d001 7172 d806 0000 5086
0000100 0000 0106 0000 0000 0002 0301 0200 0000
0000110 0000 0106 0000 0000 0000 0672 0200 0000
0000120 ee00 69c0 7272 7171 d800 f6f7 0a00 0000
0000130 4514 8098 0643 000f dc21 ffff ffff ffff
0000140 ffff ffff ffff ffff ffff ffff ffff ffff
Signed-off-by: JaimeLiao <jaimeliao.tw@gmail.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Jan Kiszka [Wed, 2 Mar 2022 14:01:56 +0000 (15:01 +0100)]
sf: Query write-protection status before operating the flash
Do not suggest successful operation if a flash area to be changed is
actually locked, thus will not execute the request. Rather report an
error and bail out. That's way more user-friendly than asking them to
manually check for this case.
Derived from original patch by Chao Zeng.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
Jan Kiszka [Wed, 2 Mar 2022 14:01:55 +0000 (15:01 +0100)]
mtd: spi: Convert is_locked callback to is_unlocked
There was no user of this callback after
5b66fdb29dc3 anymore, and its
semantic as now inconsistent between stm and sst26. What we need for the
upcoming new usecase is a "completely unlocked" semantic. So consolidate
over this.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
Vaishnav Achath [Mon, 9 May 2022 08:33:32 +0000 (14:03 +0530)]
spl: spl_spi: add spi_nor_remove() to soft reset flash
On probe, the SPI NOR core will put a flash in 8D mode if it
supports it. But Linux as of now expects to get the flash in
1S mode. Handing the flash to Linux in Octal DTR mode means
the kernel will fail to detect the flash.
This commit adds an option to soft reset the flash after
spl_spi_load_image() so that the flash can be reset to 1S mode
and subsequent spi-nor probe in Linux does not fail, since
spl_spi_load_image() performs spi_flash_probe() the remove is
added after completion loading images in spi_flash_probe() itself.
Tested on J721E EVM with 5.10 Linux kernel.
Linux spi-nor probe without the fix:
root@j7-evm:~# dmesg | grep spi-nor
[ 4.928023] spi-nor spi0.0: unrecognized JEDEC id bytes: ff ff ff ff ff ff
[ 4.934938] spi-nor: probe of spi0.0 failed with error -2
Linux spi-nor probe with the fix:
root@j7-evm:~# dmesg | grep spi-nor
[ 4.904484] spi-nor spi0.0: mt35xu512aba (65536 Kbytes)
Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
JaimeLiao [Mon, 4 Jul 2022 06:12:41 +0000 (14:12 +0800)]
mtd: spi-nor: Parse SFDP SCCR Map
Parse SCCR 22nd dword and check DTR Octal Mode Enable
Volatile bit for Octal DTR enable
Signed-off-by: JaimeLiao <jaimeliao.tw@gmail.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
JaimeLiao [Mon, 4 Jul 2022 06:12:40 +0000 (14:12 +0800)]
mtd: spi-nor-core: Adding different type of command extension in Soft Reset
Power-on-Reset is a method to restore flash back to 1S-1S-1S mode from 8D-8D-8D
in the begging of probe.
Command extension type is not standardized across flash vendors in DTR mode.
For suiting different vendor flash devices, adding a flag to seperate types for
soft reset on boot.
Signed-off-by: JaimeLiao <jaimeliao.tw@gmail.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
JaimeLiao [Mon, 4 Jul 2022 06:12:39 +0000 (14:12 +0800)]
mtd: spi-nor: add support for Macronix Octal flash
Follow patch <
f6adec1af4b2f5d3012480c6cdce7743b74a6156> (Allow using Micron mt35xu512aba
in Octal DTR mode).
Enable Octal DTR mode with 20 dummy cycles to allow running at the
maximum supported frequency for adding Macronix flash in Octal DTR mode.
-https://www.mxic.com.tw/Lists/Datasheet/Attachments/7841/MX25LM51245G,%203V,%20512Mb,%20v1.1.pdf
Signed-off-by: JaimeLiao <jaimeliao.tw@gmail.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Markus Hoffrogge [Wed, 29 Jun 2022 23:26:39 +0000 (01:26 +0200)]
sunxi-nand: fix the PIO instead of DMA implementation
The sunxi nand SPL loader was broken at least for SUN4I,
SUN5I and SUN7I SOCs since the implementation change
from DMA to PIO usage - commit 6ddbb1e.
Root cause for this issue is the NFC control flag NFC_CTL_RAM_METHOD
being set by method nand_apply_config.
This flag controls the bus being used for the NFCs internal RAM access.
It must be set for the DMA use case only.
See A33_Nand_Flash_Controller_Specification.pdf page 12.
This fix is tested by myself on a Cubietruck A20 board.
Others should test it on new generation SOCs as well.
Signed-off-by: Markus Hoffrogge <mhoffrogge@gmail.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Michal Suchanek [Thu, 7 Jul 2022 08:01:16 +0000 (10:01 +0200)]
configs: sunxi: OrangePi Zero: enable Macronix flash support
The boards that come with a flash memory pre-soldered have a Macronix
flash chip.
Fixes:
280294c5df ("sunxi: boards: Enable SPI flash support in U-Boot proper")
Signed-off-by: Michal Suchanek <msuchanek@suse.de>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Michal Suchanek [Sun, 3 Jul 2022 18:49:24 +0000 (20:49 +0200)]
sunxi: lcd: Move range from kconfig description to definition.
KConfig has range option, use it instead of notice in the option
descrition.
Signed-off-by: Michal Suchanek <msuchanek@suse.de>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Andre Przywara [Tue, 26 Apr 2022 23:08:18 +0000 (00:08 +0100)]
sunxi: licheepi_nano: enable SPI flash
Many LicheePi Nano boards come with SPI flash soldered, which already
works for booting the SPL and loading U-Boot proper.
With the updated DTB, we can now also use the SPI flash from U-Boot
proper, so enable the bits in the defconfig, to allow loading binaries
from SPI flash.
There seem to be board revisions with a Winbond SPI chip, but also
others with an XTX chip, so include support for both: the actual chip
used will be autodetected.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Andre Przywara [Tue, 26 Apr 2022 22:58:53 +0000 (23:58 +0100)]
spi: sunxi: Add support for F1C100s SPI controller
The SPI controllers in the Allwinner F1Cx00 series of SoCs are
compatible to the H3 IP. The only difference in the integration is
the missing mod clock in the F1C100, instead the SPI clock is directly
derived from the AHB clock.
We *should* be able to model this through the DT, but the addition of
get_rate() requires quite some refactoring, so it's not really worth in
this simple case: We programmed both the PLL_PERIPH to 600 MHz and the
PLL/AHB divider to 3 in the SPL, so we know the SPI base clock is 200
MHz. Since we used a hard coded fixed clock rate of 24 MHz for all the
other SoCs so far, we can as well do the same for the F1C100.
Define the SPI input clock and maximum frequency differently when
compiling for the F1C100 SoC.
Also adjust the power-of-2 divider programming, because that uses a
"minus one" encoding, compared to the other SoCs.
This allows to enable SPI flash support for the F1C100 boards.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Andre Przywara [Tue, 3 May 2022 01:06:37 +0000 (02:06 +0100)]
spi: sunxi: improve SPI clock calculation
The current SPI clock divider calculation has two problems:
- We use a normal round-down division, which results in a divider
typically being too small, resulting in a too high frequency on the bus.
- The calculaction for the power-of-two divider is very inaccurate, and
again rounds down, which might lead to wild bus frequencies.
This wasn't a real problem so far, since most chips can handle slightly
higher bus frequencies just fine. Also the actual speed was mostly lost
anyway, due to release_bus() reseting the device. And the power-of-2
calculation was probably never used, because it only applies to
frequencies below 47 KHz.
However this will become a problem for the F1C100s support, due to its
much higher base frequency.
Calculate a safe divider correctly (using round-up), and re-use that
value when calculating the power-of-2 value. We also separate the
maximum frequency and the input clock on the way, since they will be
different for the F1C100s.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Andre Przywara [Mon, 2 May 2022 23:07:16 +0000 (00:07 +0100)]
spi: sunxi: refactor SPI speed/mode programming
As George rightfully pointed out [1], the spi-sunxi driver programs the
speed and mode settings only when the respective functions are called,
but this gets lost over a call to release_bus(). That asserts the
reset line, thus forces each SPI register back to its default value.
Adding to that, trying to program SPI_CCR and SPI_TCR might be pointless
in the first place, when the reset line is still asserted (before
claim_bus()), so those setting won't apply most of the time. In reality
I see two nested claim_bus() calls for the first use, so settings between
the two would work (for instance for the initial "sf probe"). However
later on the speed setting is not programmed into the hardware anymore.
So far we get away with that default frequency, because that is a rather
tame 24 MHz, which most SPI flash chips can handle just fine.
Move the actual register programming into a separate function, and use
.set_speed and .set_mode just to set the variables in our priv structure.
Then we only call this new function in claim_bus(), when we are sure
that register accesses actually work and are preserved.
[1] https://lore.kernel.org/u-boot/
20210725231636.879913-17-me@yifangu.com/
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reported-by: George Hilliard <thirtythreeforty@gmail.com>
Icenowy Zheng [Tue, 28 Jun 2022 06:49:24 +0000 (14:49 +0800)]
spi: sunxi: use XCH status to detect in-progress transfer
The current detection of RX FIFO depth seems to be not reliable, and
XCH will self-clear when a transfer is done.
Check XCH bit when polling for transfer finish.
Signed-off-by: Icenowy Zheng <uwu@icenowy.me>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Samuel Holland [Fri, 15 Jul 2022 05:20:57 +0000 (00:20 -0500)]
net: sun8i-emac: Drop use of arch-specific header
This header is not used since commit
abdbefba2a4e ("net: sun8i_emac: Use
consistent clock bitfield definitions"). Dropping it allows the driver
to be architecture-independent.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Samuel Holland [Fri, 15 Jul 2022 05:20:56 +0000 (00:20 -0500)]
net: sun8i-emac: Downgrade printf during probe to debug
This just prints the PHY mode taken from the devicetree. It does not
need to be printed during every boot, and also avoids an unwanted
line break for the "net: " reporting line.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Andre Przywara [Mon, 4 Jul 2022 14:10:03 +0000 (15:10 +0100)]
sunxi: configs: streamline include/configs/sun*.h wrappers
For mostly historic reasons we had configuration headers for each
Allwinner CPU "family". These days they are mostly just including one
common header, with the rest being somewhat empty.
There were attempts to remove them, and to just use the one common header
to begin with, but this has implications to the build system, which me
might not be ready for, yet.
To document this behaviour, and to avoid something sneaking in over
time, make those files all the same (minus the CPU family name and
the copyrights), and add a comment explaining that.
This makes it easier to just remove those files later on, when needed
and possible.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Samuel Holland [Mon, 9 May 2022 05:29:37 +0000 (00:29 -0500)]
reset: sunxi: Reuse the platform data from the clock driver
The clock and reset drivers use the exact same platform data. Simplify
them by sharing the object. This is safe because the parent device
(the clock device) always gets its driver model callbacks run first.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Acked-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Samuel Holland [Mon, 9 May 2022 05:29:36 +0000 (00:29 -0500)]
reset: sunxi: Convert driver private data to platform data
The reason here is the same as the reason for changing the clock driver:
platform data can be provided when binding the driver.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Samuel Holland [Mon, 9 May 2022 05:29:35 +0000 (00:29 -0500)]
clk: sunxi: Convert driver private data to platform data
All of the driver private data should really be platform data since it
is determined statically (selected by the compatible string or extracted
from the devicetree). Move everything to platform data, so it can be
provided when binding the driver. This is useful for SPL, or for
instantiating the driver as part of an MFD.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Samuel Holland [Mon, 9 May 2022 05:29:34 +0000 (00:29 -0500)]
clk: sunxi: Use a single driver for all variants
Now that all of the variants use the same bind/probe functions and ops,
there is no need to have a separate driver for each variant. Since most
SoCs contain two variants (the main CCU and PRCM CCU), this saves a bit
of firmware size and RAM.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
[Andre: add F1C100s support]
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Samuel Holland [Mon, 9 May 2022 05:29:33 +0000 (00:29 -0500)]
reset: sunxi: Get the reset count from the CCU descriptor
This allows all of the clock drivers to use a common bind function.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
[Andre: add F1C100s support]
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Samuel Holland [Mon, 9 May 2022 05:29:32 +0000 (00:29 -0500)]
clk: sunxi: Prevent out-of-bounds gate array access
Because the gate arrays are not given explicit sizes, the arrays are
only as large as the highest-numbered gate described in the driver.
However, only a subset of the CCU clocks are needed by U-Boot. So there
are valid clock specifiers with indexes greater than the size of the
arrays. Referencing any of these clocks causes out-of-bounds access.
Fix this by checking the identifier against the size of the array.
Fixes:
0d47bc705651 ("clk: Add Allwinner A64 CLK driver")
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Samuel Holland [Mon, 9 May 2022 05:29:31 +0000 (00:29 -0500)]
clk: sunxi: Store the array sizes in the CCU descriptor
The reset array size is currently used for bounds checking in the reset
driver. The same bounds check should really be done in the clock driver.
Currently, the array size is provided to the reset driver separately
from the CCU descriptor, which is a bit strange. Let's do this the usual
way, with the array sizes next to the arrays themselves.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
[Andre: add F1C100s support]
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Samuel Holland [Fri, 15 Jul 2022 03:34:54 +0000 (22:34 -0500)]
musb: sunxi: Allow host-side USB with external VBUS
Now that the PHY driver will not try to drive VBUS if it is already
driven by an external supply, there is no need to check the VBUS voltage
before powering on the PHY.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Angus Ainslie [Thu, 14 Jul 2022 15:11:12 +0000 (08:11 -0700)]
configs: get rid of build warnings due to SPL_USB_DWC3_GENERIC
Adding the SPL_USB_DWC3_GENERIC symbol broke some ti builds. This
should fix the builds but untested on HW.
Signed-off-by: Angus Ainslie <angus@akkea.ca>
Angus Ainslie [Thu, 14 Jul 2022 15:11:11 +0000 (08:11 -0700)]
usb: dwc3: add a SPL_USB_DWC3_GENERIC option for the dwc3 driver
Suppress warnings when building the SPL without USB_DWC3_GENERIC
Signed-off-by: Angus Ainslie <angus@akkea.ca>
Tom Rini [Thu, 14 Jul 2022 22:43:51 +0000 (18:43 -0400)]
Merge branch '2022-07-14-migrate-wiki-to-sphinx'
- Merge the majority of the relevant wiki content to doc/process/ and
convert to Sphinx. Begin cleaning up and modernizing the content as
well to match current process. There is still more work to be done in
this regard.
Tom Rini [Tue, 12 Jul 2022 18:14:19 +0000 (14:14 -0400)]
doc: Add in the historical release statistics found on the wiki
The wiki had gitdm-generated release statistics starting with v1.3.0.
Re-generate this information as Sphinx. This aims to be as historically
accurate as possible and so some company renames were kept to their old
rather than current name until we had made the switch previously.
Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Tue, 12 Jul 2022 21:34:15 +0000 (17:34 -0400)]
doc: process: Correct and expand slightly on the Merge Window concept
For quite a long time we've been using a 3 week, rather than 2 week,
merge window as it was only 2 weeks during the timeframe where we did 2
month rather than 3 month releases. This corrects the places that still
had 2 weeks and tries to make things a bit clearer overall.
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Tue, 12 Jul 2022 21:34:14 +0000 (17:34 -0400)]
doc: Add doc/develop/release_cycle.rst
Migrate the RelaseCycle wiki page to Sphinx. In terms of visible
changes, we stop having a dynamic countdown to when the release is. And
we drop the year-based statistics, that were not being kept up to date.
For the moment, we only link to statistics for v2022.07 but will add
back the historical data in a subsequent patch.
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Thu, 14 Jul 2022 12:07:46 +0000 (08:07 -0400)]
process.rst: Modernize the "Workflow of a Custodian" section
The "Workflow of a Custodian" section on the wiki had not been changed
in quite some time to reflect how the process has been functioning for
some time. First, update some links to point to modern and current
sources of information.
Second, and more overarching, reword much of the section. This expands
on the expectations of both custodians and developers when it comes to
rebasing patches. Rework the final points to be clearer that Custodians
are expected to do their best to test the changes and ask for help when
needed, as well as that pull requests are expected in a timely manner.
Cc: Claudius Heine <ch@denx.de>
Cc: Martin Bonner <martingreybeard@gmail.com>
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Thu, 14 Jul 2022 12:07:45 +0000 (08:07 -0400)]
process.rst: Perform minor cleanups
- Use gender-neutral language to refer to the user, consistently.
- Reword a few places so that they read more naturally.
- Make the long standing practice around "Twilight Time" more clear,
hopefully.
- Replace a reference to MAKEALL with a reference to CI testing as
that's the current requirement.
Cc: Claudius Heine <ch@denx.de>
Cc: Martin Bonner <martingreybeard@gmail.com>
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Thu, 14 Jul 2022 12:07:44 +0000 (08:07 -0400)]
designprinciples.rst: Perform minor cleanups
- Remove some missed wiki markup, and escape a "\n" correctly.
- Use gender-neutral language to refer to the user, consistently.
Cc: Claudius Heine <ch@denx.de>
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Thu, 14 Jul 2022 12:07:43 +0000 (08:07 -0400)]
doc: Migrate Process wiki page to Sphinx
Move the current Process wiki page to doc/develop/process.rst. The
changes here are for formatting or slight rewording so that it reads
well when linking to other Sphinx documents.
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Thu, 14 Jul 2022 12:07:42 +0000 (08:07 -0400)]
doc: codingstyle: Remove comment about '//' style comments
For some time now we've allowed for '//' style comments, which mirrors
the Linux kernel. So drop this point here.
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Thu, 14 Jul 2022 12:07:41 +0000 (08:07 -0400)]
doc: Migrate DesignPrinciples wiki page to Sphinx
Move the current DesignPrinciples wiki page to
doc/develop/designprinciples.rst. The changes here are for formatting
or slight rewording so that it reads well when linking to other Sphinx
documents.
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Thu, 14 Jul 2022 12:07:40 +0000 (08:07 -0400)]
doc: Migrate CodingStyle wiki page to Sphinx
Move the current CodingStyle wiki page to doc/develop/codingstyle.rst.
The changes here are for formatting or slight rewording so that it reads
well when linking to other Sphinx documents.
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Thu, 14 Jul 2022 15:10:49 +0000 (11:10 -0400)]
Merge https://source.denx.de/u-boot/custodians/u-boot-usb
Fabio Estevam [Wed, 13 Jul 2022 20:39:46 +0000 (17:39 -0300)]
spl: sdp: Pass the USB index to board_usb_init()
board_usb_init() should receive the controller_index as its
first parameter instead of having it hardcoded as 0.
All in-tree users have CONFIG_SPL_SDP_USB_DEV as 0, so this error
should not affect any board.
Fix it by passing controller_index as the parameter of board_usb_init().
Signed-off-by: Fabio Estevam <festevam@denx.de>
Acked-by: Peng Fan <peng.fan@nxp.com>
Tom Rini [Thu, 14 Jul 2022 11:18:33 +0000 (07:18 -0400)]
Merge tag 'mips-pull-2022-07-13' of https://source.denx.de/u-boot/custodians/u-boot-mips
- MIPS: add drivers and board support for Mediatek MT7621 SoC
Tom Rini [Thu, 14 Jul 2022 01:31:46 +0000 (21:31 -0400)]
Merge tag 'efi-2022-10-rc1' of https://source.denx.de/u-boot/custodians/u-boot-efi
Pull request for efi-2022-10-rc1
Documentation:
* rework the mkimage.1 man-page
* add a statistics page for v2022.07
* update environment description
UEFI:
* add Ilias Apalodimas as co-maintainer
* fix a memory leak in efi_set_bootdev()
* suppress a build warning
Weijie Gao [Fri, 20 May 2022 03:24:16 +0000 (11:24 +0800)]
MAINTAINERS: update maintainer for MediaTek MIPS platform
Update maintainer for MediaTek MIPS platform
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Weijie Gao [Fri, 20 May 2022 03:24:10 +0000 (11:24 +0800)]
tools: mtk_image: add support for MT7621 NAND images
The BootROM of MT7621 requires a image header for SPL to record its size
and load address when booting from NAND.
To create such an image, one can use the following command line:
mkimage -T mtk_image -a 0x80200000 -e 0x80200000 -n "mt7621=1"
-d u-boot-spl-ddr.bin u-boot-spl-ddr.img
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Weijie Gao [Fri, 20 May 2022 03:24:04 +0000 (11:24 +0800)]
spl: nand: support loading legacy image with payload compressed
Add support to load legacy image with payload compressed. This redirects
the boot flow for all legacy images. If the payload is not compressed, the
actual behavior will remain unchanged.
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Weijie Gao [Fri, 20 May 2022 03:23:58 +0000 (11:23 +0800)]
spl: spl_legacy: fix the use of SPL_COPY_PAYLOAD_ONLY
If the payload is compressed, SPL_COPY_PAYLOAD_ONLY should always be set
since the payload will not be directly read to its load address. The
payload will first be read to a temporary buffer, and then be decompressed
to its load address, without image header.
If the payload is not compressed, and SPL_COPY_PAYLOAD_ONLY is set, image
header should be skipped on loading. Otherwise image header should also be
read to its load address.
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Weijie Gao [Fri, 20 May 2022 03:23:53 +0000 (11:23 +0800)]
spl: allow using nand base without standard nand driver
This patch removes the dependency to SPL_NAND_DRIVERS for SPL_NAND_BASE to
allow minimal spl nand driver to use nand base for probing NAND chips.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Weijie Gao [Fri, 20 May 2022 03:23:47 +0000 (11:23 +0800)]
nand: raw: add support for MediaTek MT7621 SoC
This patch adds NAND flash controller driver for MediaTek MT7621 SoC.
The NAND flash controller of MT7621 supports only SLC NAND flashes.
It supports 4~12 bits correction with maximum 4KB page size.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Weijie Gao [Fri, 20 May 2022 03:23:42 +0000 (11:23 +0800)]
net: mediatek: add support for MediaTek MT7621 SoC
This patch adds GMAC support for MediaTek MT7621 SoC.
MT7621 has the same GMAC/Switch configuration as MT7623.
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Weijie Gao [Fri, 20 May 2022 03:23:37 +0000 (11:23 +0800)]
net: mediatek: use regmap api to modify ethsys registers
The address returned by regmap_get_range() is not remapped. Directly r/w
to this address is ok for ARM platforms since it's idential to the virtual
address.
But for MIPS platform only virtual address should be used for access.
To solve this issue, the regmap api regmap_read/regmap_write should be used
since they will remap address before accessing.
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Weijie Gao [Fri, 20 May 2022 03:23:31 +0000 (11:23 +0800)]
net: mediatek: remap iobase address
The iobase address from dts node is actually physical address. It's
identical to the virtual address in ARM platform. This is ok because this
driver was used only by ARM platforms (mt7622/mt7623 ...).
But now this driver will be used by mt7621 which is a MIPS SoC. For MIPS
platform the physical address space is mapped to KSEG0 and KSEG1 and this
makes the virtual address apparently not idential to its physical address.
To solve this issue, this patch replaces dev_read_addr with dev_remap_addr
to get the remapped iobase address.
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Weijie Gao [Fri, 20 May 2022 03:23:26 +0000 (11:23 +0800)]
mmc: mediatek: add support for MediaTek MT7621 SoC
This patch adds SDXC support for MediaTek MT7621 SoC
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Weijie Gao [Fri, 20 May 2022 03:23:19 +0000 (11:23 +0800)]
watchdog: add support for MediaTek MT7621 SoC
This patch makes mt7621_wdt driver available for MediaTek MT7621 SoC
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Weijie Gao [Fri, 20 May 2022 03:23:14 +0000 (11:23 +0800)]
gpio: add support for MediaTek MT7621 SoC
This patch makes mt7621_gpio driver available for MediaTek MT7621 SoC
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Weijie Gao [Fri, 20 May 2022 03:23:08 +0000 (11:23 +0800)]
spi: add support for MediaTek MT7621 SoC
This patch makes mt7621_spi driver available for MediaTek MT7621 SoC
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Weijie Gao [Fri, 20 May 2022 03:23:01 +0000 (11:23 +0800)]
phy: mtk-tphy: add support for MediaTek MT7621 SoC
This patch makes mtk-tphy driver available for MediaTek MT7621 SoC
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Weijie Gao [Fri, 20 May 2022 03:22:56 +0000 (11:22 +0800)]
usb: xhci-mtk: add support for MediaTek MT7621 SoC
This patch makes xhci-mtk driver available for MediaTek MT7621 SoC
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Weijie Gao [Fri, 20 May 2022 03:22:49 +0000 (11:22 +0800)]
pinctrl: mtmips: add support for MediaTek MT7621 SoC
This patch adds pinctrl support for MediaTek MT7621 SoC.
The MT7621 SoC supports pinconf, but it is not the same as mt7628.
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Weijie Gao [Fri, 20 May 2022 03:22:41 +0000 (11:22 +0800)]
reset: mtmips: add reset controller support for MediaTek MT7621 SoC
This patch adds reset controller bits definition header file for MediaTek
MT7621 SoC
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Weijie Gao [Fri, 20 May 2022 03:22:36 +0000 (11:22 +0800)]
clk: mtmips: add clock driver for MediaTek MT7621 SoC
This patch adds a clock driver for MediaTek MT7621 SoC.
This driver provides clock gate control as well as getting clock frequency
for CPU/SYS/XTAL and some peripherals.
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Weijie Gao [Fri, 20 May 2022 03:22:31 +0000 (11:22 +0800)]
doc: mediatek: add documentation for mt7621 reference boards
The MT7621 requires external binary blob being executed during u-boot's
boot-up flow. It's necessary to provide a guide here for users to correctly
build the u-boot.
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Weijie Gao [Fri, 20 May 2022 03:22:26 +0000 (11:22 +0800)]
mips: mtmips: add two reference boards for mt7621
The mt7621_rfb board supports integrated giga PHYs plus one external
giga PHYs. It also has up to 512MiB DDR3, 16MB SPI-NOR, 3 mini PCI-e x1
slots, SDXC and USB.
The mt7621_nand_rfb board is almost the same as mt7621_rfb board, but it
uses NAND flash and SDXC is not available.
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Weijie Gao [Fri, 20 May 2022 03:22:21 +0000 (11:22 +0800)]
mips: mtmips: add support for MediaTek MT7621 SoC
This patch adds support for MediaTek MT7621 SoC.
All files are dedicated for u-boot.
The default build target is u-boot-mt7621.bin.
The specification of this chip:
https://www.mediatek.com/products/homenetworking/mt7621
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Weijie Gao [Fri, 20 May 2022 03:21:51 +0000 (11:21 +0800)]
mips: add support for noncached_alloc()
This patch adds support for noncached_alloc() which was only supported by
ARM platform.
Unlike the ARM platform, MMU is not used in u-boot for MIPS. Instead, KSEG
is provided to access uncached memory. So most code of this patch is copied
from cache.c of ARM platform, with only two differences:
1. MMU is untouched in noncached_set_region()
2. Address returned by noncached_alloc() is converted using KSEG1ADDR()
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Weijie Gao [Fri, 20 May 2022 03:21:45 +0000 (11:21 +0800)]
mips: add __image_copy_len for SPL linker script
This patch adds __image_copy_len needed by TPL of MT7621 SoC.
The __image_copy_len represents the binary blob size of both SPL/TPL
binaries. To achieve this, __text_start/end are added for calculation.
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Weijie Gao [Fri, 20 May 2022 03:21:39 +0000 (11:21 +0800)]
mips: add more definitions for asm/cm.h
This patch add more definitions needed for MT7621 initialization.
MT7621 needs to initialize GIC/CPC and other related parts.
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Weijie Gao [Fri, 20 May 2022 03:21:34 +0000 (11:21 +0800)]
mips: add asm/mipsmtregs.h for MIPS multi-threading
To be compatible with old u-boot used by lots of MT7621 devices, the u-boot
needs to boot-up MT7621's all cores, and all VPES of each core.
This patch adds asm/mipsmtregs.h from linux kernel which is need for
boot-up VPEs.
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Heinrich Schuchardt [Tue, 12 Jul 2022 10:38:42 +0000 (12:38 +0200)]
MAINTAINERS: add Ilias Apalodimas to EFI PAYLOAD as co-maintainer
Ilias has since long been reviewing UEFI patches.
Now he has volunteered to assist me in maintaining the sub-system.
Cc: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Heinrich Schuchardt [Tue, 12 Jul 2022 06:11:53 +0000 (08:11 +0200)]
efi_loader: suppress executable stack warning
When linking EFI binaries the linker emits:
ld.bfd: warning: lib/efi_loader/efi_crt0.o:
missing .note.GNU-stack section implies executable stack
Suppress the warning.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Heinrich Schuchardt [Sun, 10 Jul 2022 13:46:57 +0000 (15:46 +0200)]
efi_loader: memory leak in efi_set_bootdev()
efi_dp_str() allocates memory which should be released after use.
Use %pD printf code. Adjust message wording.
Fixes:
d837cb1e3b6b ("efi: Add debugging to efi_set_bootdev()")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
projects / platform / kernel / u-boot.git / log