review.tizen.org Git - platform/kernel/linux-starfive.git/log

net: phy: at803x: add fiber support

Previously this driver always forced the copper page to be selected,
however for AR8031 in 100Base-FX or 1000Base-X modes, the fiber page
needs to be selected. Set the appropriate mode based on the hardware
mode_cfg strap selection.

Enable the appropriate interrupt bits to detect fiber-side link up
or down events.

Update config_aneg and read_status methods to use the appropriate
Clause 37 calls when fiber mode is in use.

Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: phy: at803x: move page selection fix to config_init

The fix to select the copper page on AR8031 was being done in the probe
function rather than config_init, so it would not be redone after resume
from suspend. Move this to config_init so it is always redone when
needed.

Fixes: c329e5afb42f ("net: phy: at803x: select correct page on config init")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tcp: allocate tcp_death_row outside of struct netns_ipv4

I forgot tcp had per netns tracking of timewait sockets,
and their sysctl to change the limit.

After 0dad4087a86a ("tcp/dccp: get rid of inet_twsk_purge()"),
whole struct net can be freed before last tw socket is freed.

We need to allocate a separate struct inet_timewait_death_row
object per netns.

tw_count becomes a refcount and gains associated debugging infrastructure.

BUG: KASAN: use-after-free in inet_twsk_kill+0x358/0x3c0 net/ipv4/inet_timewait_sock.c:46
Read of size 8 at addr ffff88807d5f9f40 by task kworker/1:7/3690

CPU: 1 PID: 3690 Comm: kworker/1:7 Not tainted 5.16.0-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Workqueue: events pwq_unbound_release_workfn
Call Trace:
<IRQ>
__dump_stack lib/dump_stack.c:88 [inline]
dump_stack_lvl+0xcd/0x134 lib/dump_stack.c:106
print_address_description.constprop.0.cold+0x8d/0x336 mm/kasan/report.c:255
__kasan_report mm/kasan/report.c:442 [inline]
kasan_report.cold+0x83/0xdf mm/kasan/report.c:459
inet_twsk_kill+0x358/0x3c0 net/ipv4/inet_timewait_sock.c:46
call_timer_fn+0x1a5/0x6b0 kernel/time/timer.c:1421
expire_timers kernel/time/timer.c:1466 [inline]
__run_timers.part.0+0x67c/0xa30 kernel/time/timer.c:1734
__run_timers kernel/time/timer.c:1715 [inline]
run_timer_softirq+0xb3/0x1d0 kernel/time/timer.c:1747
__do_softirq+0x29b/0x9c2 kernel/softirq.c:558
invoke_softirq kernel/softirq.c:432 [inline]
__irq_exit_rcu+0x123/0x180 kernel/softirq.c:637
irq_exit_rcu+0x5/0x20 kernel/softirq.c:649
sysvec_apic_timer_interrupt+0x93/0xc0 arch/x86/kernel/apic/apic.c:1097
</IRQ>
<TASK>
asm_sysvec_apic_timer_interrupt+0x12/0x20 arch/x86/include/asm/idtentry.h:638
RIP: 0010:lockdep_unregister_key+0x1c9/0x250 kernel/locking/lockdep.c:6328
Code: 00 00 00 48 89 ee e8 46 fd ff ff 4c 89 f7 e8 5e c9 ff ff e8 09 cc ff ff 9c 58 f6 c4 02 75 26 41 f7 c4 00 02 00 00 74 01 fb 5b <5d> 41 5c 41 5d 41 5e 41 5f e9 19 4a 08 00 0f 0b 5b 5d 41 5c 41 5d
RSP: 0018:ffffc90004077cb8 EFLAGS: 00000206
RAX: 0000000000000046 RBX: ffff88807b61b498 RCX: 0000000000000001
RDX: dffffc0000000000 RSI: 0000000000000000 RDI: 0000000000000000
RBP: ffff888077027128 R08: 0000000000000001 R09: ffffffff8f1ea4fc
R10: fffffbfff1ff93ee R11: 000000000000af1e R12: 0000000000000246
R13: 0000000000000000 R14: ffffffff8ffc89b8 R15: ffffffff90157fb0
wq_unregister_lockdep kernel/workqueue.c:3508 [inline]
pwq_unbound_release_workfn+0x254/0x340 kernel/workqueue.c:3746
process_one_work+0x9ac/0x1650 kernel/workqueue.c:2307
worker_thread+0x657/0x1110 kernel/workqueue.c:2454
kthread+0x2e9/0x3a0 kernel/kthread.c:377
ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:295
</TASK>

Allocated by task 3635:
kasan_save_stack+0x1e/0x50 mm/kasan/common.c:38
kasan_set_track mm/kasan/common.c:46 [inline]
set_alloc_info mm/kasan/common.c:437 [inline]
__kasan_slab_alloc+0x90/0xc0 mm/kasan/common.c:470
kasan_slab_alloc include/linux/kasan.h:260 [inline]
slab_post_alloc_hook mm/slab.h:732 [inline]
slab_alloc_node mm/slub.c:3230 [inline]
slab_alloc mm/slub.c:3238 [inline]
kmem_cache_alloc+0x202/0x3a0 mm/slub.c:3243
kmem_cache_zalloc include/linux/slab.h:705 [inline]
net_alloc net/core/net_namespace.c:407 [inline]
copy_net_ns+0x125/0x760 net/core/net_namespace.c:462
create_new_namespaces+0x3f6/0xb20 kernel/nsproxy.c:110
unshare_nsproxy_namespaces+0xc1/0x1f0 kernel/nsproxy.c:226
ksys_unshare+0x445/0x920 kernel/fork.c:3048
__do_sys_unshare kernel/fork.c:3119 [inline]
__se_sys_unshare kernel/fork.c:3117 [inline]
__x64_sys_unshare+0x2d/0x40 kernel/fork.c:3117
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x35/0xb0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x44/0xae

The buggy address belongs to the object at ffff88807d5f9a80
which belongs to the cache net_namespace of size 6528
The buggy address is located 1216 bytes inside of
6528-byte region [ffff88807d5f9a80, ffff88807d5fb400)
The buggy address belongs to the page:
page:ffffea0001f57e00 refcount:1 mapcount:0 mapping:0000000000000000 index:0xffff88807d5f9a80 pfn:0x7d5f8
head:ffffea0001f57e00 order:3 compound_mapcount:0 compound_pincount:0
memcg:ffff888070023001
flags: 0xfff00000010200(slab|head|node=0|zone=1|lastcpupid=0x7ff)
raw: 00fff00000010200 ffff888010dd4f48 ffffea0001404e08 ffff8880118fd000
raw: ffff88807d5f9a80 0000000000040002 00000001ffffffff ffff888070023001
page dumped because: kasan: bad access detected
page_owner tracks the page as allocated
page last allocated via order 3, migratetype Unmovable, gfp_mask 0xd20c0(__GFP_IO|__GFP_FS|__GFP_NOWARN|__GFP_NORETRY|__GFP_COMP|__GFP_NOMEMALLOC), pid 3634, ts 119694798460, free_ts 119693556950
prep_new_page mm/page_alloc.c:2434 [inline]
get_page_from_freelist+0xa72/0x2f50 mm/page_alloc.c:4165
__alloc_pages+0x1b2/0x500 mm/page_alloc.c:5389
alloc_pages+0x1aa/0x310 mm/mempolicy.c:2271
alloc_slab_page mm/slub.c:1799 [inline]
allocate_slab mm/slub.c:1944 [inline]
new_slab+0x28a/0x3b0 mm/slub.c:2004
___slab_alloc+0x87c/0xe90 mm/slub.c:3018
__slab_alloc.constprop.0+0x4d/0xa0 mm/slub.c:3105
slab_alloc_node mm/slub.c:3196 [inline]
slab_alloc mm/slub.c:3238 [inline]
kmem_cache_alloc+0x35c/0x3a0 mm/slub.c:3243
kmem_cache_zalloc include/linux/slab.h:705 [inline]
net_alloc net/core/net_namespace.c:407 [inline]
copy_net_ns+0x125/0x760 net/core/net_namespace.c:462
create_new_namespaces+0x3f6/0xb20 kernel/nsproxy.c:110
unshare_nsproxy_namespaces+0xc1/0x1f0 kernel/nsproxy.c:226
ksys_unshare+0x445/0x920 kernel/fork.c:3048
__do_sys_unshare kernel/fork.c:3119 [inline]
__se_sys_unshare kernel/fork.c:3117 [inline]
__x64_sys_unshare+0x2d/0x40 kernel/fork.c:3117
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x35/0xb0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x44/0xae
page last free stack trace:
reset_page_owner include/linux/page_owner.h:24 [inline]
free_pages_prepare mm/page_alloc.c:1352 [inline]
free_pcp_prepare+0x374/0x870 mm/page_alloc.c:1404
free_unref_page_prepare mm/page_alloc.c:3325 [inline]
free_unref_page+0x19/0x690 mm/page_alloc.c:3404
skb_free_head net/core/skbuff.c:655 [inline]
skb_release_data+0x65d/0x790 net/core/skbuff.c:677
skb_release_all net/core/skbuff.c:742 [inline]
__kfree_skb net/core/skbuff.c:756 [inline]
consume_skb net/core/skbuff.c:914 [inline]
consume_skb+0xc2/0x160 net/core/skbuff.c:908
skb_free_datagram+0x1b/0x1f0 net/core/datagram.c:325
netlink_recvmsg+0x636/0xea0 net/netlink/af_netlink.c:1998
sock_recvmsg_nosec net/socket.c:948 [inline]
sock_recvmsg net/socket.c:966 [inline]
sock_recvmsg net/socket.c:962 [inline]
____sys_recvmsg+0x2c4/0x600 net/socket.c:2632
___sys_recvmsg+0x127/0x200 net/socket.c:2674
__sys_recvmsg+0xe2/0x1a0 net/socket.c:2704
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x35/0xb0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x44/0xae

Memory state around the buggy address:
ffff88807d5f9e00: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
ffff88807d5f9e80: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
>ffff88807d5f9f00: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
^
ffff88807d5f9f80: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
ffff88807d5fa000: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb

Fixes: 0dad4087a86a ("tcp/dccp: get rid of inet_twsk_purge()")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Reported-by: Paolo Abeni <pabeni@redhat.com>
Tested-by: Paolo Abeni <pabeni@redhat.com>
Link: https://lore.kernel.org/r/20220126180714.845362-1-eric.dumazet@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

nfp: only use kdoc style comments for kdoc

Update comments to only use kdoc style comments, starting with '/**',
for kdoc.

Flagged by ./scripts/kernel-doc

Signed-off-by: Simon Horman <simon.horman@corigine.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://lore.kernel.org/r/20220126090803.5582-1-simon.horman@corigine.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: ethernet: cortina: permit to set mac address in DT

Add ability of setting mac address in DT for cortina ethernet driver.

Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20220125210811.54350-1-clabbe@baylibre.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

nfp: flower: Use struct_size() helper in kmalloc()

Make use of the struct_size() helper instead of an open-coded version,
in order to avoid any potential type mistakes or integer overflows that,
in the worst scenario, could lead to heap overflows.

Also, address the following sparse warnings:
drivers/net/ethernet/netronome/nfp/flower/tunnel_conf.c:359:25: warning: using sizeof on a flexible structure

Link: https://github.com/KSPP/linux/issues/174
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Acked-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

mlxsw: spectrum_kvdl: Use struct_size() helper in kzalloc()

Make use of the struct_size() helper instead of an open-coded version,
in order to avoid any potential type mistakes or integer overflows that,
in the worst scenario, could lead to heap overflows.

Also, address the following sparse warnings:
drivers/net/ethernet/mellanox/mlxsw/spectrum1_kvdl.c:229:24: warning: using sizeof on a flexible structure

Link: https://github.com/KSPP/linux/issues/174
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: enetc: use .mac_select_pcs() interface

Convert the PCS selection to use mac_select_pcs, which allows the PCS
to perform any validation it needs.

Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dpaa2-mac: use .mac_select_pcs() interface

Convert dpaa2-mac to use the mac_select_pcs() interface rather than
using phylink_set_pcs(). The intention here is to unify the approach
for PCS and eventually to remove phylink_set_pcs().

Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'axienet-pcs-modernize'

Russell King says:

====================
net: axienet: modernise pcs implementation

These two patches modernise the Xilinx axienet PCS implementation to
use the phylink split PCS support.

The first patch adds split PCS support and makes use of the newly
introduced mac_select_pcs() function, which is the preferred way to
conditionally attach a PCS.

The second patch cleans up the use of mdiobus_write() since we now have
bus accessors for mdio devices.

There should be no functional change to the driver.

This series was previously sent CFT on the 16th December (message ID
Ybs1cdM3KUTsq4Vx@shell.armlinux.org.uk), and feedback addressed. CFT v2
sent 4th January (message ID YdQlI8gcVwg2sR+5@shell.armlinux.org.uk).
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

net: axienet: replace mdiobus_write() with mdiodev_write()

Commit 0ebecb2644c8 ("net: mdio: Add helper functions for accessing
MDIO devices") added support for mdiodev accessor operations that
neatly wrap the mdiobus accessor operations. Since we are dealing with
a mdio device here, update the driver to use mdiodev_write().

Tested-by: Harini Katakam <harini.katakam@xilinx.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: axienet: convert to phylink_pcs

Convert axienet to use the phylink_pcs layer, resulting in it no longer
being a legacy driver.

Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'bnxt_en-RTC'

Michael Chan says:

====================
bnxt_en: Add RTC mode for PTP

This series adds Real Time Clock (RTC) mode for PTP timestamping.  In
RTC mode, the 64-bit time value is programmed into the NIC's PTP
hardware clock (PHC).  Prior to this, the PHC is running as a free
counter.  For example, in multi-function environment, we need to run
PTP in RTC mode.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Handle async event when the PHC is updated in RTC mode

In Multi-host environment, when the PHC is updated by one host,
an async message from firmware will be sent to other hosts.
Re-initialize the timecounter when the driver receives this
async message.

Cc: Richard Cochran <richardcochran@gmail.com>
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Implement .adjtime() for PTP RTC mode

The adjusted time is set in the PHC in RTC mode. We also need to
update the snapshots ptp->current_time and ptp->old_time when the
time is adjusted.

Cc: Richard Cochran <richardcochran@gmail.com>
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Add driver support to use Real Time Counter for PTP

Add support for RTC mode if it is supported by firmware. In RTC
mode, the PHC is set to the 64-bit clock. Because the legacy interface
is 48-bit, the driver still has to keep track of the upper 16 bits and
handle the rollover.

Cc: Richard Cochran <richardcochran@gmail.com>
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: PTP: Refactor PTP initialization functions

Making the ptp free and timecounter initialization code into separate
functions so that later patches can use them.

Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Update firmware interface to 1.10.2.73

The main changes are PTP support for RTC, additional NVM error codes,
backing store v2 firmware APIs.

Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'stmmac-PCS-modernize'

Russell King says:

====================
net: stmmac/xpcs: modernise PCS support

This series updates xpcs and stmmac for the recent changes to phylink
to better support split PCS and to get rid of private MAC validation
functions.

This series is slightly more involved than other conversions as stmmac
has already had optional proper split PCS support.

The first six patches of this series were originally posted on 16th
December for CFT, and Wong Vee Khee reported his Intel Elkhart Lake
setup was fine the first six these. However, no tested-by was given.

The patches:

1) Provide a function to query the xpcs for the interface modes that
   are supported.

2) Populates the MAC capabilities and switches stmmac_validate() to use
   phylink_get_linkmodes(). We do not use phylink_generic_validate() yet
   as (a) we do not always have the supported interfaces populated, and
   (b) the existing code does not restrict based on interface. There
   should be no functional effect from this patch.

3) Populates phylink's supported interfaces from the xpcs when the xpcs
   is configured by firmware and also the firmware configured interface
   mode. Note: this will restrict stmmac to only supporting these
   interfaces modes - stmmac maintainers need to verify that this
   behaviour is acceptable.

4) stmmac_validate() tail-calls xpcs_validate(), but we don't need it to
   now that PCS have their own validation method. Convert stmmac and
   xpcs to use this method instead.

5) xpcs sets the poll field of phylink_pcs to true, meaning xpcs
   requires its status to be polled. There is no need to also set the
   phylink_config.pcs_poll. Remove this.

6) Switch to phylink_generic_validate(). This is probably the most
   contravertial change in this patch set as this will cause the MAC to
   restrict link modes based on the interface mode. From an inspection
   of the xpcs driver, this should be safe, as XPCS only further
   restricts the link modes to a subset of these (whether that is
   correct or not is not an issue I am addressing here.) For
   implementations that do not use xpcs, this is a more open question
   and needs feedback from stmmac maintainers.

7) Convert to use mac_select_pcs() rather than phylink_set_pcs() to set
   the PCS - the intention is to eventually remove phylink_set_pcs()
   once there are no more users of this.

v2: fix signoff and temporary warning in patch 4
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

net: stmmac: use .mac_select_pcs() interface

Convert stmmac to use the mac_select_pcs() interface rather than using
phylink_set_pcs(). The intention here is to unify the approach for PCS
and eventually to remove phylink_set_pcs().

Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: stmmac: convert to phylink_generic_validate()

Convert stmmac to use phylink_generic_validate() now that we have the
MAC capabilities and supported interfaces filled in, and we have the
PCS validation handled via the PCS operations.

Tested-by: Wong Vee Khee <vee.khee.wong@linux.intel.com> # Intel EHL Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: stmmac: remove phylink_config.pcs_poll usage

Phylink will use PCS polling whenever the PCS's poll member is set, so
setting phylink_config.pcs_poll as well is redundant.

Tested-by: Wong Vee Khee <vee.khee.wong@linux.intel.com> # Intel EHL Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: stmmac/xpcs: convert to pcs_validate()

stmmac explicitly calls the xpcs driver to validate the ethtool
linkmodes. This is no longer necessary as phylink now supports
validation through a PCS method. Convert both drivers to use this
new mechanism.

Tested-by: Wong Vee Khee <vee.khee.wong@linux.intel.com> # Intel EHL
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: stmmac: fill in supported_interfaces

Fill in phylink's supported_interfaces bitmap with the PHY interface
modes which can be used to talk to the PHY.

We indicate that the PHY interface mode passed in platform data is
always supported, as this is the initial mode passed into phylink.
When there is no PCS specified, we assume that this is the only mode
that is supported - indeed, the driver appears not to support dynamic
switching of interface types at present.

When a xpcs is present, it defines the PHY interface modes that the
stmmac driver can support. Request the supported interfaces from the
xpcs driver, and pass them to phylink.

Tested-by: Wong Vee Khee <vee.khee.wong@linux.intel.com> # Intel EHL Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: stmmac: convert to phylink_get_linkmodes()

Add the MAC speed, duplex and pause capabilities to the phylink_config
structure, and switch stmmac_validate() to use phylink_get_linkmodes()
to generate the mask of supported ethtool link modes.

Tested-by: Wong Vee Khee <vee.khee.wong@linux.intel.com> # Intel EHL Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: xpcs: add support for retrieving supported interface modes

Add a function to the xpcs driver to retrieve the supported PHY
interface modes, which can be used by drivers to fill in phylink's
supported_interfaces mask.

We validate the interface bit index to ensure that it fits within the
bitmap as xpcs lists PHY_INTERFACE_MODE_MAX in an entry.

Tested-by: Wong Vee Khee <vee.khee.wong@linux.intel.com> # Intel EHL Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'mlxsw-RJ45'

Ido Schimmel says:

====================
mlxsw: Add RJ45 ports support

We are in the process of qualifying a new system that has RJ45 ports as
opposed to the transceiver modules (e.g., SFP, QSFP) present on all
existing systems.

This patchset adds support for these ports in mlxsw by adding a couple of
missing BaseT link modes and rejecting ethtool operations that are
specific to transceiver modules.

Patchset overview:

Patches #1-#3 are cleanups and preparations.

Patch #4 adds support for two new link modes.

Patches #5-#6 query and cache the port module's type (e.g., QSFP, RJ45)
during initialization.

Patches #7-#9 forbid ethtool operations that are invalid on RJ45 ports.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

mlxsw: core_env: Forbid module reset on RJ45 ports

Transceiver module reset through 'rst' field in PMAOS register is not
supported on RJ45 ports, so module reset should be rejected.

Therefore, before trying to access this field, validate the port module
type that was queried during initialization and return an error to user
space in case the port module type is RJ45 (twisted pair).

Output example:

# ethtool --reset swp11 phy
ETHTOOL_RESET 0x40
Cannot issue ETHTOOL_RESET: Invalid argument
$ dmesg
mlxsw_spectrum 0000:03:00.0 swp11: Reset module is not supported on port module type

Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

mlxsw: core_env: Forbid power mode set and get on RJ45 ports

PMMP (Port Module Memory Map Properties) and MCION (Management Cable IO
and Notifications) registers are not supported on RJ45 ports, so setting
and getting power mode should be rejected.

Therefore, before trying to access those registers, validate the port
module type that was queried during initialization and return an error
to user space in case the port module type is RJ45 (twisted pair).

Set output example:

# ethtool --set-module swp1 power-mode-policy auto
netlink error: mlxsw_core: Power mode is not supported on port module type
netlink error: Invalid argument

Get output example:

$ ethtool --show-module swp11
netlink error: mlxsw_core: Power mode is not supported on port module type
netlink error: Invalid argument

Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

mlxsw: core_env: Forbid getting module EEPROM on RJ45 ports

MCIA (Management Cable Info Access) register is not supported on RJ45
ports, so getting module EEPROM should be rejected.

Therefore, before trying to access this register, validate the port
module type that was queried during initialization and return an error
to user space in case the port module type is RJ45 (twisted pair).

Examples for output when trying to get EEPROM module:

Using netlink:

# ethtool -m swp1
netlink error: mlxsw_core: EEPROM is not equipped on port module type
netlink error: Invalid argument

Using IOCTL:

# ethtool -m swp1
Cannot get module EEPROM information: Invalid argument
$ dmesg
mlxsw_spectrum 0000:03:00.0 swp1: EEPROM is not equipped on port module type

Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

mlxsw: core_env: Query and store port module's type during initialization

Query and store port module's type during initialization so that it
could be later used to determine if certain configurations are allowed
based on the type.

Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

mlxsw: reg: Add Port Module Type Mapping register

Add the Port Module Type Mapping (PMTP) register. It will be used by
subsequent patches to query port module types and forbid certain
configurations based on the port module's type.

Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

mlxsw: spectrum_ethtool: Add support for two new link modes

As part of a process for supporting a new system with RJ45 connectors,
100BaseT and 1000BaseT link modes need to be supported.

Add support for these two link modes by adding the two corresponding
bits in PTYS (Port Type and Speed) register.

Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

mlxsw: Add netdev argument to mlxsw_env_get_module_info()

The next patches will forbid querying the port module's EEPROM info when
its type is RJ45 as in this case no transceiver module can ever be
connected to the port.

Add netdev argument to mlxsw_env_get_module_info() so it could be used
to print an error to the kernel log via netdev_err().

Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

mlxsw: core_env: Do not pass number of modules as argument

The number of modules can be resolved from the first argument, so do not
pass it.

Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

mlxsw: spectrum_ethtool: Remove redundant variable

Remove the 'err' variable and simply return.

Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: Adjust sk_gso_max_size once when set

sk_gso_max_size is set based on the dst dev. Both users of it
adjust the value by the same offset - (MAX_TCP_HEADER + 1). Rather
than compute the same adjusted value on each call do the adjustment
once when set.

Signed-off-by: David Ahern <dsahern@kernel.org>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20220125024511.27480-1-dsahern@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: tulip: remove redundant assignment to variable new_csr6

Variable new_csr6 is being initialized with a value that is never
read, it is being re-assigned later on. The assignment is redundant
and can be removed.

Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Link: https://lore.kernel.org/r/20220123183440.112495-1-colin.i.king@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

ipv6: gro: flush instead of assuming different flows on hop_limit mismatch

IPv6 GRO considers packets to belong to different flows when their
hop_limit is different. This seems counter-intuitive, the flow is
the same. hop_limit may vary because of various bugs or hacks but
that doesn't mean it's okay for GRO to reorder packets.

Practical impact of this problem on overall TCP performance
is unclear, but TCP itself detects this reordering and bumps
TCPSACKReorder resulting in user complaints.

Eric warns that there may be performance regressions in setups
which do packet spraying across links with similar RTT but different
hop count. To be safe let's target -next and not treat this
as a fix. If the packet spraying is using flow label there should
be no difference in behavior as flow label is checked first.

Note that the code plays an easy to miss trick by upcasting next_hdr
to a u16 pointer and compares next_hdr and hop_limit in one go.

Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: mana: Use struct_size() helper in mana_gd_create_dma_region()

Make use of the struct_size() helper instead of an open-coded version,
in order to avoid any potential type mistakes or integer overflows that,
in the worst scenario, could lead to heap overflows.

Also, address the following sparse warnings:
drivers/net/ethernet/microsoft/mana/gdma_main.c:677:24: warning: using sizeof on a flexible structure

Link: https://github.com/KSPP/linux/issues/174
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

r8169: use new PM macros

This is based on series [0] that extended the PM core. Now the compiler
can see the PM callbacks also on systems not defining CONFIG_PM.
The optimizer will remove the functions then in this case.

[0] https://lore.kernel.org/netdev/20211207002102.26414-1-paul@crapouillou.net/

Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'dsa-avoid-cross-chip-vlan-sync'

Tobias Waldekranz says:

====================
net: dsa: Avoid cross-chip syncing of VLAN filtering

This bug has been latent in the source for quite some time, I suspect
due to the homogeneity of both typical configurations and hardware.

On singlechip systems, this would never be triggered. The only reason
I saw it on my multichip system was because not all chips had the same
number of ports, which means that the misdemeanor alien call turned
into a felony array-out-of-bounds access.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: Avoid cross-chip syncing of VLAN filtering

Changes to VLAN filtering are not applicable to cross-chip
notifications.

On a system like this:

.-----.   .-----.   .-----.
| sw1 +---+ sw2 +---+ sw3 |
'-1-2-'   '-1-2-'   '-1-2-'

Before this change, upon sw1p1 leaving a bridge, a call to
dsa_port_vlan_filtering would also be made to sw2p1 and sw3p1.

In this scenario:

.---------.   .-----.   .-----.
|   sw1   +---+ sw2 +---+ sw3 |
'-1-2-3-4-'   '-1-2-'   '-1-2-'

When sw1p4 would leave a bridge, dsa_port_vlan_filtering would be
called for sw2 and sw3 with a non-existing port - leading to array
out-of-bounds accesses and crashes on mv88e6xxx.

Fixes: d371b7c92d19 ("net: dsa: Unset vlan_filtering when ports leave the bridge")
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: Move VLAN filtering syncing out of dsa_switch_bridge_leave

Most of dsa_switch_bridge_leave was, in fact, dealing with the syncing
of VLAN filtering for switches on which that is a global
setting. Separate the two phases to prepare for the cross-chip related
bugfix in the following commit.

Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'netns-speedup-dismantle'

Eric Dumazet says:

====================
netns: speedup netns dismantles

netns are dismantled by a single thread, from cleanup_net()

On hosts with many TCP sockets, and/or many cpus, this thread
is spending too many cpu cycles, and can not keep up with some
workloads.

- Removing 3*num_possible_cpus() sockets per netns, for icmp and tcp protocols.
- Iterating over all TCP sockets to remove stale timewait sockets.

This patch series removes ~50% of cleanup_net() cpu costs on
hosts with 256 cpus. It also reduces per netns memory footprint.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

ipv4/tcp: do not use per netns ctl sockets

TCP ipv4 uses per-cpu/per-netns ctl sockets in order to send
RST and some ACK packets (on behalf of TIMEWAIT sockets).

This adds memory and cpu costs, which do not seem needed.
Now typical servers have 256 or more cores, this adds considerable
tax to netns users.

tcp sockets are used from BH context, are not receiving packets,
and do not store any persistent state but the 'struct net' pointer
in order to be able to use IPv4 output functions.

Note that I attempted a related change in the past, that had
to be hot-fixed in commit bdbbb8527b6f ("ipv4: tcp: get rid of ugly unicast_sock")

This patch could very well surface old bugs, on layers not
taking care of sk->sk_kern_sock properly.

Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ipv6: do not use per netns icmp sockets

Back in linux-2.6.25 (commit 98c6d1b261e7 "[NETNS]: Make icmpv6_sk per namespace.",
we added private per-cpu/per-netns ipv6 icmp sockets.

This adds memory and cpu costs, which do not seem needed.
Now typical servers have 256 or more cores, this adds considerable
tax to netns users.

icmp sockets are used from BH context, are not receiving packets,
and do not store any persistent state but the 'struct net' pointer.

icmpv6_xmit_lock() already makes sure to lock the chosen per-cpu
socket.

This patch has a considerable impact on the number of netns
that the worker thread in cleanup_net() can dismantle per second,
because ip6mr_sk_done() is no longer called, meaning we no longer
acquire the rtnl mutex, competing with other threads adding new netns.

Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ipv4: do not use per netns icmp sockets

Back in linux-2.6.25 (commit 4a6ad7a141cb "[NETNS]: Make icmp_sk per namespace."),
we added private per-cpu/per-netns ipv4 icmp sockets.

This adds memory and cpu costs, which do not seem needed.
Now typical servers have 256 or more cores, this adds considerable
tax to netns users.

icmp sockets are used from BH context, are not receiving packets,
and do not store any persistent state but the 'struct net' pointer.

icmp_xmit_lock() already makes sure to lock the chosen per-cpu
socket.

Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tcp/dccp: get rid of inet_twsk_purge()

Prior patches in the series made sure tw_timer_handler()
can be fired after netns has been dismantled/freed.

We no longer have to scan a potentially big TCP ehash
table at netns dismantle.

Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tcp/dccp: no longer use twsk_net(tw) from tw_timer_handler()

We will soon get rid of inet_twsk_purge().

This means that tw_timer_handler() might fire after
a netns has been dismantled/freed.

Instead of adding a function (and data structure) to find a netns
from tw->tw_net_cookie, just update the SNMP counters
a bit earlier, when the netns is known to be alive.

Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tcp/dccp: add tw->tw_bslot

We want to allow inet_twsk_kill() working even if netns
has been dismantled/freed, to get rid of inet_twsk_purge().

This patch adds tw->tw_bslot to cache the bind bucket slot
so that inet_twsk_kill() no longer needs to dereference twsk_net(tw)

Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'ionic-fw-recovery'

Shannon Nelson says:

====================
ionic: updates for stable FW recovery

Recent FW work has tightened up timings in its error recovery
handling and uncovered weaknesses in the driver's responses,
so this is a set of updates primarily for better handling of
the firmware's recovery mechanisms.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

ionic: replace set_vf data with union

This (ab)use of a data buffer made some static code checkers
rather itchy, so we replace the a generic data buffer with
the union in the struct ionic_vf_setattr_cmd.

Fixes: fbb39807e9ae ("ionic: support sr-iov operations")
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>

ionic: stretch heartbeat detection

The driver can be premature in detecting stalled firmware
when the heartbeat is not updated because the firmware can
occasionally take a long time (more than 2 seconds) to service
a request, and doesn't update the heartbeat during that time.

The firmware heartbeat is not necessarily a steady 1 second
periodic beat, but better described as something that should
progress at least once in every DECVMD_TIMEOUT period.
The single-threaded design in the FW means that if a devcmd
or adminq request launches a large internal job, it is stuck
waiting for that job to finish before it can get back to
updating the heartbeat.  Since all requests are "guaranteed"
to finish within the DEVCMD_TIMEOUT period, the driver needs
to less aggressive in checking the heartbeat progress.

We change our current 2 second window to something bigger than
DEVCMD_TIMEOUT which should take care of most of the issue.
We stop checking for the heartbeat while waiting for a request,
as long as we're still watching for the FW status.  Lastly,
we make sure our FW status is up to date before running a
devcmd request.

Once we do this, we need to not check the heartbeat on DEV
commands because it may be stalled while we're on the fw_down
path.  Instead, we can rely on the is_fw_running check.

Fixes: b2b9a8d7ed13 ("ionic: avoid races in ionic_heartbeat_check")
Signed-off-by: Brett Creeley <brett@pensando.io>
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>

ionic: remove the dbid_inuse bitmap

The dbid_inuse bitmap is not useful in this driver so remove it.

Fixes: 6461b446f2a0 ("ionic: Add interrupts and doorbells")
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>

ionic: disable napi when ionic_lif_init() fails

When the driver is going through reset, it will eventually call
ionic_lif_init(), which does a lot of re-initialization. One
of the re-initialization steps is to setup the adminq and
enable napi for it. If something breaks after this point
we can end up with a kernel NULL pointer dereference through
ionic_adminq_napi.

Fix this by making sure to call napi_disable() in the cleanup
path of ionic_lif_init(). This forces any pending napi contexts
to finish and prevents them from being recalled before deleting
the napi context.

Fixes: 77ceb68e29cc ("ionic: Add notifyq support")
Signed-off-by: Brett Creeley <brett@pensando.io>
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>

ionic: Cleanups in the Tx hotpath code

Buffer DMA mapping happens in ionic_tx_map_skb() and this function is
called from ionic_tx() and ionic_tx_tso(). If ionic_tx_map_skb()
succeeds, but a failure is encountered later in ionic_tx() or
ionic_tx_tso() we aren't unmapping the buffers. This can be fixed in
ionic_tx() by changing functions it calls to return void because they
always return 0. For ionic_tx_tso(), there's an actual possibility that
we leave the buffers mapped, so fix this by introducing the helper
function ionic_tx_desc_unmap_bufs(). This function is also re-used
in ionic_tx_clean().

Fixes: 0f3154e6bcb3 ("ionic: Add Tx and Rx handling")
Signed-off-by: Brett Creeley <brett@pensando.io>
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>

ionic: Prevent filter add/del err msgs when the device is not available

Currently when a request for add/deleting a filter is made when
ionic_heartbeat_check() returns failure the driver will be overly
verbose about failures, especially when these are usually temporary
fails and the request will be retried later. An example of this is
a filter add when the FW is in the middle of resetting:

IONIC_CMD_RX_FILTER_ADD (31) failed: IONIC_RC_ERROR (-6)
rx_filter add failed: ADDR 01:80:c2:00:00:0e

Fix this by checking for -ENXIO and other error values on filter
request fails before printing the error message. Add similar
checking to the delete filter code.

Fixes: f91958cc9622 ("ionic: tame the filter no space message")
Signed-off-by: Brett Creeley <brett@pensando.io>
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>

ionic: Query FW when getting VF info via ndo_get_vf_config

Currently when an administrator configures a VF via ndo_set_vf*,
the driver will send the set command to FW and then update the
cached value. The cached value is then used when reporting
VF info via ndo_get_vf_config.

A problem is that the VF info may have been updated between
the last ndo_set_vf* and ndo_get_vf_info commands via some
other method, i.e. a VF changes its MAC address (assuming it's
allowed to do so) and since this is all managed by the FW,
this new value won't be reflected in the PF's cache of values.

To fix this, update the driver to always get the latest VF
information by making use of the IONIC_CMD_VF_GETATTR dev
command. The FW may not support getting all the attributes for
IONIC_CMD_VF_GETATTR, so the driver will only update the cached
VF config members if their associated IONIC_CMD_VF_GETATTR
was successful. Otherwise the cached VF config members will
remain the same as what was set in ndo_set_vf*.

Fixes: fbb39807e9ae ("ionic: support sr-iov operations")
Signed-off-by: Brett Creeley <brett@pensando.io>
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>

ionic: Allow flexibility for error reporting on dev commands

When dev commands fail, an error message will always be printed,
which may be overly alarming the to system administrators,
especially if the driver shouldn't be printing the error due
to some unsupported capability.

Similar to recent adminq request changes, we can update the
dev command interface with the ability to selectively print
error messages to allow the driver to prevent printing errors
that are expected.

Signed-off-by: Brett Creeley <brett@pensando.io>
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>

ionic: Correctly print AQ errors if completions aren't received

Recent changes went into the driver to allow flexibility when
printing error messages. Unfortunately this had the unexpected
consequence of printing confusing messages like the following:

IONIC_CMD_RX_FILTER_ADD (31) failed: IONIC_RC_SUCCESS (-6)

In cases like this the completion of the admin queue command never
completes, so the completion status is 0, hence IONIC_RC_SUCCESS
is printed even though the command clearly failed. For example,
this could happen when the driver tries to add a filter and at
the same time the FW goes through a reset, so the AQ command
never completes.

Fix this by forcing the FW completion status to IONIC_RC_ERROR
in cases where we never get the completion.

Fixes: 8c9d956ab6fb ("ionic: allow adminq requests to override default error message")
Signed-off-by: Brett Creeley <brett@pensando.io>
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>

ionic: fix up printing of timeout error

Make sure we print the TIMEOUT string if we had a timeout
error, rather than printing the wrong status.

Fixes: 8c9d956ab6fb ("ionic: allow adminq requests to override default error message")
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>

ionic: better handling of RESET event

When IONIC_EVENT_RESET is received, we only need to start the
fw_down process if we aren't already down, and we need to be
sure to set the FW_STOPPING state on the way.

If this is how we noticed that FW was stopped, it is most
likely from a FW update, and we'll see a new FW generation.
The update happens quickly enough that we might not see
fw_status==0, so we need to be sure things get restarted when
we see the fw_generation change.

Fixes: d2662072c094 ("ionic: monitor fw status generation")
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>

ionic: add FW_STOPPING state

Between fw running and fw actually stopped into reset, we need
a fw_stopping concept to catch and block some actions while
we're transitioning to FW_RESET state. This will help to be
sure the fw_up task is not scheduled until after the fw_down
task has completed.

On some rare occasion timing, it is possible for the fw_up task
to try to run before the fw_down task, then not get run after
the fw_down task has run, leaving the device in a down state.
This is possible if the watchdog goes off in between finding the
down transition and starting the fw_down task, where the later
watchdog sees the FW is back up and schedules a fw_up task.

Fixes: c672412f6172 ("ionic: remove lifs on fw reset")
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>

ionic: Don't send reset commands if FW isn't running

It's possible the FW is already shutting down while the driver is being
removed and/or when the driver is going through reset. This can cause
unexpected/unnecessary errors to be printed:

eth0: DEV_CMD IONIC_CMD_PORT_RESET (12) error, IONIC_RC_ERROR (29) failed
eth1: DEV_CMD IONIC_CMD_RESET (3) error, IONIC_RC_ERROR (29) failed

Fix this by checking the FW status register before issuing the reset
commands.

Also, since err may not be assigned in ionic_port_reset(), assign it a
default value of 0, and remove an unnecessary log message.

Fixes: fbfb8031533c ("ionic: Add hardware init and device commands")
Signed-off-by: Brett Creeley <brett@pensando.io>
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>

ionic: separate function for watchdog init

Pull the watchdog init code out to a separate bite-sized
function. Code cleaning for now, will be a useful change in
the near future.

Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>

ionic: start watchdog after all is setup

The watchdog expects the lif to fully exist when it goes off,
so lets not start the watchdog until all is ready in case there
is some quirky time dialation that makes probe take multiple
seconds.

Fixes: 089406bc5ad6 ("ionic: add a watchdog timer to monitor heartbeat")
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>

ionic: fix type complaint in ionic_dev_cmd_clean()

Sparse seems to have gotten a little more picky lately and
we need to revisit this bit of code to make sparse happy.

warning: incorrect type in initializer (different address spaces)
   expected union ionic_dev_cmd_regs *regs
   got union ionic_dev_cmd_regs [noderef] __iomem *dev_cmd_regs
warning: incorrect type in argument 2 (different address spaces)
   expected void [noderef] __iomem *
   got unsigned int *
warning: incorrect type in argument 1 (different address spaces)
   expected void volatile [noderef] __iomem *
   got union ionic_dev_cmd *

Fixes: d701ec326a31 ("ionic: clean up sparse complaints")
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>

ipv4: get rid of fib_info_hash_{alloc|free}

Use kvzalloc()/kvfree() instead of hand coded functions.

Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ip6_tunnel: allow routing IPv4 traffic in NBMA mode

Since IPv4 routes support IPv6 gateways now, we can route IPv4 traffic in
NBMA tunnels.

Signed-off-by: Qing Deng <i@moy.cat>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: use bool values to pass bool param of phy_init_eee()

The 2nd param of phy_init_eee(): clk_stop_enable is a bool param, use
true or false instead of 1/0.

Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220123152241.1480-1-jszhang@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: fec_ptp: remove redundant initialization of variable val

Variable val is being initialized with a value that is never read,
it is being re-assigned later. The assignment is redundant and
can be removed.

Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Reviewed-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Link: https://lore.kernel.org/r/20220123184936.113486-1-colin.i.king@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: usb: asix: remove redundant assignment to variable reg

Variable reg is being masked however the variable is never read
after this. The assignment is redundant and can be removed.

Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/r/20220123184035.112785-1-colin.i.king@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Merge https://git./linux/kernel/git/bpf/bpf-next

Daniel Borkmann says:

====================
pull-request: bpf-next 2022-01-24

We've added 80 non-merge commits during the last 14 day(s) which contain
a total of 128 files changed, 4990 insertions(+), 895 deletions(-).

The main changes are:

1) Add XDP multi-buffer support and implement it for the mvneta driver,
   from Lorenzo Bianconi, Eelco Chaudron and Toke Høiland-Jørgensen.

2) Add unstable conntrack lookup helpers for BPF by using the BPF kfunc
   infra, from Kumar Kartikeya Dwivedi.

3) Extend BPF cgroup programs to export custom ret value to userspace via
   two helpers bpf_get_retval() and bpf_set_retval(), from YiFei Zhu.

4) Add support for AF_UNIX iterator batching, from Kuniyuki Iwashima.

5) Complete missing UAPI BPF helper description and change bpf_doc.py script
   to enforce consistent & complete helper documentation, from Usama Arif.

6) Deprecate libbpf's legacy BPF map definitions and streamline XDP APIs to
   follow tc-based APIs, from Andrii Nakryiko.

7) Support BPF_PROG_QUERY for BPF programs attached to sockmap, from Di Zhu.

8) Deprecate libbpf's bpf_map__def() API and replace users with proper getters
   and setters, from Christy Lee.

9) Extend libbpf's btf__add_btf() with an additional hashmap for strings to
   reduce overhead, from Kui-Feng Lee.

10) Fix bpftool and libbpf error handling related to libbpf's hashmap__new()
    utility function, from Mauricio Vásquez.

11) Add support to BTF program names in bpftool's program dump, from Raman Shukhau.

12) Fix resolve_btfids build to pick up host flags, from Connor O'Brien.

* https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next: (80 commits)
  selftests, bpf: Do not yet switch to new libbpf XDP APIs
  selftests, xsk: Fix rx_full stats test
  bpf: Fix flexible_array.cocci warnings
  xdp: disable XDP_REDIRECT for xdp frags
  bpf: selftests: add CPUMAP/DEVMAP selftests for xdp frags
  bpf: selftests: introduce bpf_xdp_{load,store}_bytes selftest
  net: xdp: introduce bpf_xdp_pointer utility routine
  bpf: generalise tail call map compatibility check
  libbpf: Add SEC name for xdp frags programs
  bpf: selftests: update xdp_adjust_tail selftest to include xdp frags
  bpf: test_run: add xdp_shared_info pointer in bpf_test_finish signature
  bpf: introduce frags support to bpf_prog_test_run_xdp()
  bpf: move user_size out of bpf_test_init
  bpf: add frags support to xdp copy helpers
  bpf: add frags support to the bpf_xdp_adjust_tail() API
  bpf: introduce bpf_xdp_get_buff_len helper
  net: mvneta: enable jumbo frames if the loaded XDP program support frags
  bpf: introduce BPF_F_XDP_HAS_FRAGS flag in prog_flags loading the ebpf program
  net: mvneta: add frags support to XDP_TX
  xdp: add frags support to xdp_return_{buff/frame}
  ...
====================

Link: https://lore.kernel.org/r/20220124221235.18993-1-daniel@iogearbox.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

selftests, bpf: Do not yet switch to new libbpf XDP APIs

Revert commit 544356524dd6 ("selftests/bpf: switch to new libbpf XDP APIs")
for now given this will heavily conflict with 4b27480dcaa7 ("bpf/selftests:
convert xdp_link test to ASSERT_* macros") upon merge. Andrii agreed to redo
the conversion cleanly after trees merged.

Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andrii@kernel.org>

Merge tag 'linux-can-fixes-for-5.17-20220124' of git://git./linux/kernel/git/mkl/linux-can

Marc Kleine-Budde says:

====================
pull-request: can 2022-01-24

The first patch updates the email address of Brian Silverman from his
former employer to his private address.

The next patch fixes DT bindings information for the tcan4x5x SPI CAN
driver.

The following patch targets the m_can driver and fixes the
introduction of FIFO bulk read support.

Another patch for the tcan4x5x driver, which fixes the max register
value for the regmap config.

The last patch for the flexcan driver marks the RX mailbox support for
the MCF5441X as support.

* tag 'linux-can-fixes-for-5.17-20220124' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can:
  can: flexcan: mark RX via mailboxes as supported on MCF5441X
  can: tcan4x5x: regmap: fix max register value
  can: m_can: m_can_fifo_{read,write}: don't read or write from/to FIFO if length is 0
  dt-bindings: can: tcan4x5x: fix mram-cfg RX FIFO config
  mailmap: update email address of Brian Silverman
====================

Link: https://lore.kernel.org/r/20220124175955.3464134-1-mkl@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

can: flexcan: mark RX via mailboxes as supported on MCF5441X

Most flexcan IP cores support 2 RX modes:
- FIFO
- mailbox

The flexcan IP core on the MCF5441X cannot receive CAN RTR messages
via mailboxes. However the mailbox mode is more performant. The commit

| 1c45f5778a3b ("can: flexcan: add ethtool support to change rx-rtr setting during runtime")

added support to switch from FIFO to mailbox mode on these cores.

After testing the mailbox mode on the MCF5441X by Angelo Dureghello,
this patch marks it (without RTR capability) as supported. Further the
IP core overview table is updated, that RTR reception via mailboxes is
not supported.

Link: https://lore.kernel.org/all/20220121084425.3141218-1-mkl@pengutronix.de
Tested-by: Angelo Dureghello <angelo@kernel-space.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

can: tcan4x5x: regmap: fix max register value

The MRAM of the tcan4x5x has a size of 2K and starts at 0x8000. There
are no further registers in the tcan4x5x making 0x87fc the biggest
addressable register.

This patch fixes the max register value of the regmap config from
0x8ffc to 0x87fc.

Fixes: 6e1caaf8ed22 ("can: tcan4x5x: fix max register value")
Link: https://lore.kernel.org/all/20220119064011.2943292-1-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

can: m_can: m_can_fifo_{read,write}: don't read or write from/to FIFO if length is 0

In order to optimize FIFO access, especially on m_can cores attached
to slow busses like SPI, in patch

| e39381770ec9 ("can: m_can: Disable IRQs on FIFO bus errors")

bulk read/write support has been added to the m_can_fifo_{read,write}
functions.

That change leads to the tcan driver to call
regmap_bulk_{read,write}() with a length of 0 (for CAN frames with 0
data length). regmap treats this as an error:

| tcan4x5x spi1.0 tcan4x5x0: FIFO write returned -22

This patch fixes the problem by not calling the
cdev->ops->{read,write)_fifo() in case of a 0 length read/write.

Fixes: e39381770ec9 ("can: m_can: Disable IRQs on FIFO bus errors")
Link: https://lore.kernel.org/all/20220114155751.2651888-1-mkl@pengutronix.de
Cc: stable@vger.kernel.org
Cc: Matt Kline <matt@bitbashing.io>
Cc: Chandrasekar Ramakrishnan <rcsekar@samsung.com>
Reported-by: Michael Anochin <anochin@photo-meter.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

dt-bindings: can: tcan4x5x: fix mram-cfg RX FIFO config

This tcan4x5x only comes with 2K of MRAM, a RX FIFO with a dept of 32
doesn't fit into the MRAM. Use a depth of 16 instead.

Fixes: 4edd396a1911 ("dt-bindings: can: tcan4x5x: Add DT bindings for TCAN4x5X driver")
Link: https://lore.kernel.org/all/20220119062951.2939851-1-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

mailmap: update email address of Brian Silverman

Brian Silverman's address at bluerivertech.com is not valid anymore,
use Brian's private email address instead.

Link: https://lore.kernel.org/all/20220110082359.2019735-1-mkl@pengutronix.de
Cc: Brian Silverman <bsilver16384@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

selftests, xsk: Fix rx_full stats test

Fix the rx_full stats test so that it correctly reports pass even when
the fill ring is not full of buffers.

Fixes: 872a1184dbf2 ("selftests: xsk: Put the same buffer only once in the fill ring")
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Tested-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Acked-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Link: https://lore.kernel.org/bpf/20220121123508.12759-1-magnus.karlsson@gmail.com

bpf: Fix flexible_array.cocci warnings

Zero-length and one-element arrays are deprecated, see:
Documentation/process/deprecated.rst

Flexible-array members should be used instead.

Generated by: scripts/coccinelle/misc/flexible_array.cocci

Fixes: c1ff181ffabc ("selftests/bpf: Extend kfunc selftests")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: kernel test robot <lkp@intel.com>
Signed-off-by: Julia Lawall <julia.lawall@inria.fr>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Kumar Kartikeya Dwivedi <memxor@gmail.com>
Link: https://lore.kernel.org/bpf/alpine.DEB.2.22.394.2201221206320.12220@hadrien

net: stmmac: remove unused members in struct stmmac_priv

The tx_coalesce and mii_irq are not used at all now, so remove them.

Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: atlantic: Use the bitmap API instead of hand-writing it

Simplify code by using bitmap_weight() and bitmap_zero() instead of
hand-writing these functions.

Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ping: fix the sk_bound_dev_if match in ping_lookup

When 'ping' changes to use PING socket instead of RAW socket by:

# sysctl -w net.ipv4.ping_group_range="0 100"

the selftests 'router_broadcast.sh' will fail, as such command

# ip vrf exec vrf-h1 ping -I veth0 198.51.100.255 -b

can't receive the response skb by the PING socket. It's caused by mismatch
of sk_bound_dev_if and dif in ping_rcv() when looking up the PING socket,
as dif is vrf-h1 if dif's master was set to vrf-h1.

This patch is to fix this regression by also checking the sk_bound_dev_if
against sdif so that the packets can stil be received even if the socket
is not bound to the vrf device but to the real iif.

Fixes: c319b4d76b9e ("net: ipv4: add IPPROTO_ICMP socket kind")
Reported-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net/smc: Transitional solution for clcsock race issue

We encountered a crash in smc_setsockopt() and it is caused by
accessing smc->clcsock after clcsock was released.

BUG: kernel NULL pointer dereference, address: 0000000000000020
#PF: supervisor read access in kernel mode
#PF: error_code(0x0000) - not-present page
PGD 0 P4D 0
Oops: 0000 [#1] PREEMPT SMP PTI
CPU: 1 PID: 50309 Comm: nginx Kdump: loaded Tainted: G E     5.16.0-rc4+ #53
RIP: 0010:smc_setsockopt+0x59/0x280 [smc]
Call Trace:
  <TASK>
  __sys_setsockopt+0xfc/0x190
  __x64_sys_setsockopt+0x20/0x30
  do_syscall_64+0x34/0x90
  entry_SYSCALL_64_after_hwframe+0x44/0xae
RIP: 0033:0x7f16ba83918e
  </TASK>

This patch tries to fix it by holding clcsock_release_lock and
checking whether clcsock has already been released before access.

In case that a crash of the same reason happens in smc_getsockopt()
or smc_switch_to_fallback(), this patch also checkes smc->clcsock
in them too. And the caller of smc_switch_to_fallback() will identify
whether fallback succeeds according to the return value.

Fixes: fd57770dd198 ("net/smc: wait for pending work before clcsock release_sock")
Link: https://lore.kernel.org/lkml/5dd7ffd1-28e2-24cc-9442-1defec27375e@linux.ibm.com/T/
Signed-off-by: Wen Gu <guwen@linux.alibaba.com>
Acked-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ibmvnic: remove unused ->wait_capability

With previous bug fix, ->wait_capability flag is no longer needed and can
be removed.

Fixes: 249168ad07cd ("ibmvnic: Make CRQ interrupt tasklet wait for all capabilities crqs")
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.ibm.com>
Reviewed-by: Dany Madden <drt@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ibmvnic: don't spin in tasklet

ibmvnic_tasklet() continuously spins waiting for responses to all
capability requests. It does this to avoid encountering an error
during initialization of the vnic. However if there is a bug in the
VIOS and we do not receive a response to one or more queries the
tasklet ends up spinning continuously leading to hard lock ups.

If we fail to receive a message from the VIOS it is reasonable to
timeout the login attempt rather than spin indefinitely in the tasklet.

Fixes: 249168ad07cd ("ibmvnic: Make CRQ interrupt tasklet wait for all capabilities crqs")
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.ibm.com>
Reviewed-by: Dany Madden <drt@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ibmvnic: init ->running_cap_crqs early

We use ->running_cap_crqs to determine when the ibmvnic_tasklet() should
send out the next protocol message type. i.e when we get back responses
to all our QUERY_CAPABILITY CRQs we send out REQUEST_CAPABILITY crqs.
Similiary, when we get responses to all the REQUEST_CAPABILITY crqs, we
send out the QUERY_IP_OFFLOAD CRQ.

We currently increment ->running_cap_crqs as we send out each CRQ and
have the ibmvnic_tasklet() send out the next message type, when this
running_cap_crqs count drops to 0.

This assumes that all the CRQs of the current type were sent out before
the count drops to 0. However it is possible that we send out say 6 CRQs,
get preempted and receive all the 6 responses before we send out the
remaining CRQs. This can result in ->running_cap_crqs count dropping to
zero before all messages of the current type were sent and we end up
sending the next protocol message too early.

Instead initialize the ->running_cap_crqs upfront so the tasklet will
only send the next protocol message after all responses are received.

Use the cap_reqs local variable to also detect any discrepancy (either
now or in future) in the number of capability requests we actually send.

Currently only send_query_cap() is affected by this behavior (of sending
next message early) since it is called from the worker thread (during
reset) and from application thread (during ->ndo_open()) and they can be
preempted. send_request_cap() is only called from the tasklet which
processes CRQ responses sequentially, is not be affected. But to
maintain the existing symmtery with send_query_capability() we update
send_request_capability() also.

Fixes: 249168ad07cd ("ibmvnic: Make CRQ interrupt tasklet wait for all capabilities crqs")
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.ibm.com>
Reviewed-by: Dany Madden <drt@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ibmvnic: Allow extra failures before disabling

If auto-priority-failover (APF) is enabled and there are at least two
backing devices of different priorities, some resets like fail-over,
change-param etc can cause at least two back to back failovers. (Failover
from high priority backing device to lower priority one and then back
to the higher priority one if that is still functional).

Depending on the timimg of the two failovers it is possible to trigger
a "hard" reset and for the hard reset to fail due to failovers. When this
occurs, the driver assumes that the network is unstable and disables the
VNIC for a 60-second "settling time". This in turn can cause the ethtool
command to fail with "No such device" while the vnic automatically recovers
a little while later.

Given that it's possible to have two back to back failures, allow for extra
failures before disabling the vnic for the settling time.

Fixes: f15fde9d47b8 ("ibmvnic: delay next reset if hard reset fails")
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.ibm.com>
Reviewed-by: Dany Madden <drt@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ipv4: fix ip option filtering for locally generated fragments

During IP fragmentation we sanitize IP options. This means overwriting
options which should not be copied with NOPs. Only the first fragment
has the original, full options.

ip_fraglist_prepare() copies the IP header and options from previous
fragment to the next one. Commit 19c3401a917b ("net: ipv4: place control
buffer handling away from fragmentation iterators") moved sanitizing
options before ip_fraglist_prepare() which means options are sanitized
and then overwritten again with the old values.

Fixing this is not enough, however, nor did the sanitization work
prior to aforementioned commit.

ip_options_fragment() (which does the sanitization) uses ipcb->opt.optlen
for the length of the options. ipcb->opt of fragments is not populated
(it's 0), only the head skb has the state properly built. So even when
called at the right time ip_options_fragment() does nothing. This seems
to date back all the way to v2.5.44 when the fast path for pre-fragmented
skbs had been introduced. Prior to that ip_options_build() would have been
called for every fragment (in fact ever since v2.5.44 the fragmentation
handing in ip_options_build() has been dead code, I'll clean it up in
-next).

In the original patch (see Link) caixf mentions fixing the handling
for fragments other than the second one, but I'm not sure how _any_
fragment could have had their options sanitized with the code
as it stood.

Tested with python (MTU on lo lowered to 1000 to force fragmentation):

  import socket
  s = socket.socket(socket.AF_INET, socket.SOCK_DGRAM)
  s.setsockopt(socket.IPPROTO_IP, socket.IP_OPTIONS,
               bytearray([7,4,5,192, 20|0x80,4,1,0]))
  s.sendto(b'1'*2000, ('127.0.0.1', 1234))

Before:

IP (tos 0x0, ttl 64, id 1053, offset 0, flags [+], proto UDP (17), length 996, options (RR [bad length 4] [bad ptr 5] 192.148.4.1,,RA value 256))
    localhost.36500 > localhost.search-agent: UDP, length 2000
IP (tos 0x0, ttl 64, id 1053, offset 968, flags [+], proto UDP (17), length 996, options (RR [bad length 4] [bad ptr 5] 192.148.4.1,,RA value 256))
    localhost > localhost: udp
IP (tos 0x0, ttl 64, id 1053, offset 1936, flags [none], proto UDP (17), length 100, options (RR [bad length 4] [bad ptr 5] 192.148.4.1,,RA value 256))
    localhost > localhost: udp

After:

IP (tos 0x0, ttl 96, id 42549, offset 0, flags [+], proto UDP (17), length 996, options (RR [bad length 4] [bad ptr 5] 192.148.4.1,,RA value 256))
    localhost.51607 > localhost.search-agent: UDP, bad length 2000 > 960
IP (tos 0x0, ttl 96, id 42549, offset 968, flags [+], proto UDP (17), length 996, options (NOP,NOP,NOP,NOP,RA value 256))
    localhost > localhost: udp
IP (tos 0x0, ttl 96, id 42549, offset 1936, flags [none], proto UDP (17), length 100, options (NOP,NOP,NOP,NOP,RA value 256))
    localhost > localhost: udp

RA (20 | 0x80) is now copied as expected, RR (7) is "NOPed out".

Link: https://lore.kernel.org/netdev/20220107080559.122713-1-ooppublic@163.com/
Fixes: 19c3401a917b ("net: ipv4: place control buffer handling away from fragmentation iterators")
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: caixf <ooppublic@163.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

net-procfs: show net devices bound packet types

After commit:7866a621043f ("dev: add per net_device packet type chains"),
we can not get packet types that are bound to a specified net device by
/proc/net/ptype, this patch fix the regression.

Run "tcpdump -i ens192 udp -nns0" Before and after apply this patch:

Before:
  [root@localhost ~]# cat /proc/net/ptype
  Type Device      Function
  0800          ip_rcv
  0806          arp_rcv
  86dd          ipv6_rcv

After:
  [root@localhost ~]# cat /proc/net/ptype
  Type Device      Function
  ALL  ens192   tpacket_rcv
  0800          ip_rcv
  0806          arp_rcv
  86dd          ipv6_rcv

v1 -> v2:
  - fix the regression rather than adding new /proc API as
    suggested by Stephen Hemminger.

Fixes: 7866a621043f ("dev: add per net_device packet type chains")
Signed-off-by: Jianguo Wu <wujianguo@chinatelecom.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>

bonding: use rcu_dereference_rtnl when get bonding active slave

bond_option_active_slave_get_rcu() should not be used in rtnl_mutex as it
use rcu_dereference(). Replace to rcu_dereference_rtnl() so we also can use
this function in rtnl protected context.

With this update, we can rmeove the rcu_read_lock/unlock in
bonding .ndo_eth_ioctl and .get_ts_info.

Reported-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Fixes: 94dd016ae538 ("bond: pass get_ts_info and SIOC[SG]HWTSTAMP ioctl to active device")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: sfp: ignore disabled SFP node

Commit ce0aa27ff3f6 ("sfp: add sfp-bus to bridge between network devices
and sfp cages") added code which finds SFP bus DT node even if the node
is disabled with status = "disabled". Because of this, when phylink is
created, it ends with non-null .sfp_bus member, even though the SFP
module is not probed (because the node is disabled).

We need to ignore disabled SFP bus node.

Fixes: ce0aa27ff3f6 ("sfp: add sfp-bus to bridge between network devices and sfp cages")
Signed-off-by: Marek Behún <kabel@kernel.org>
Cc: stable@vger.kernel.org # 2203cbf2c8b5 ("net: sfp: move fwnode parsing into sfp-bus layer")
Signed-off-by: David S. Miller <davem@davemloft.net>

selftests: net: ioam: expect support for Queue depth data

The IOAM queue-depth data field was added a few weeks ago,
but the test unit was not updated accordingly.

Reported-by: kernel test robot <oliver.sang@intel.com>
Fixes: b63c5478e9cb ("ipv6: ioam: Support for Queue depth data field")
Signed-off-by: Justin Iurman <justin.iurman@uliege.be>
Link: https://lore.kernel.org/r/20220121173449.26918-1-justin.iurman@uliege.be
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

mptcp: Use struct_group() to avoid cross-field memset()

In preparation for FORTIFY_SOURCE performing compile-time and run-time
field bounds checking for memcpy(), memmove(), and memset(), avoid
intentionally writing across neighboring fields.

Use struct_group() to capture the fields to be reset, so that memset()
can be appropriately bounds-checked by the compiler.

Cc: Matthieu Baerts <matthieu.baerts@tessares.net>
Cc: mptcp@lists.linux.dev
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Link: https://lore.kernel.org/r/20220121073935.1154263-1-keescook@chromium.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

rxrpc: Adjust retransmission backoff

Improve retransmission backoff by only backing off when we retransmit data
packets rather than when we set the lost ack timer.

To this end:

(1) In rxrpc_resend(), use rxrpc_get_rto_backoff() when setting the
     retransmission timer and only tell it that we are retransmitting if we
     actually have things to retransmit.

     Note that it's possible for the retransmission algorithm to race with
     the processing of a received ACK, so we may see no packets needing
     retransmission.

(2) In rxrpc_send_data_packet(), don't bump the backoff when setting the
     ack_lost_at timer, as it may then get bumped twice.

With this, when looking at one particular packet, the retransmission
intervals were seen to be 1.5ms, 2ms, 3ms, 5ms, 9ms, 17ms, 33ms, 71ms,
136ms, 264ms, 544ms, 1.088s, 2.1s, 4.2s and 8.3s.

Fixes: c410bf01933e ("rxrpc: Fix the excessive initial retransmission timeout")
Suggested-by: Marc Dionne <marc.dionne@auristor.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Marc Dionne <marc.dionne@auristor.com>
Tested-by: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
Link: https://lore.kernel.org/r/164138117069.2023386.17446904856843997127.stgit@warthog.procyon.org.uk/
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'mvneta: introduce XDP multi-buffer support'

Lorenzo Bianconi says:

====================

This series introduces XDP frags support. The mvneta driver is
the first to support these new "non-linear" xdp_{buff,frame}. Reviewers
please focus on how these new types of xdp_{buff,frame} packets
traverse the different layers and the layout design. It is on purpose
that BPF-helpers are kept simple, as we don't want to expose the
internal layout to allow later changes.

The main idea for the new XDP frags layout is to reuse the same
structure used for non-linear SKB. This rely on the "skb_shared_info"
struct at the end of the first buffer to link together subsequent
buffers. Keeping the layout compatible with SKBs is also done to ease
and speedup creating a SKB from an xdp_{buff,frame}.
Converting xdp_frame to SKB and deliver it to the network stack is shown
in patch 05/18 (e.g. cpumaps).

A frags bit (XDP_FLAGS_HAS_FRAGS) has been introduced in the flags
field of xdp_{buff,frame} structure to notify the bpf/network layer if
this is a non-linear xdp frame (XDP_FLAGS_HAS_FRAGS set) or not
(XDP_FLAGS_HAS_FRAGS not set).
The frags bit will be set by a xdp frags capable driver only
for non-linear frames maintaining the capability to receive linear frames
without any extra cost since the skb_shared_info structure at the end
of the first buffer will be initialized only if XDP_FLAGS_HAS_FRAGS bit
is set. Moreover the flags field in xdp_{buff,frame} will be reused even for
xdp rx csum offloading in future series.

Typical use cases for this series are:
- Jumbo-frames
- Packet header split (please see Google’s use-case @ NetDevConf 0x14, [0])
- TSO/GRO for XDP_REDIRECT

The three following ebpf helpers (and related selftests) has been introduced:
- bpf_xdp_load_bytes:
  This helper is provided as an easy way to load data from a xdp buffer. It
  can be used to load len bytes from offset from the frame associated to
  xdp_md, into the buffer pointed by buf.
- bpf_xdp_store_bytes:
  Store len bytes from buffer buf into the frame associated to xdp_md, at
  offset.
- bpf_xdp_get_buff_len:
  Return the total frame size (linear + paged parts)

bpf_xdp_adjust_tail and bpf_xdp_copy helpers have been modified to take into
account non-linear xdp frames.
Moreover, similar to skb_header_pointer, we introduced bpf_xdp_pointer utility
routine to return a pointer to a given position in the xdp_buff if the
requested area (offset + len) is contained in a contiguous memory area
otherwise it must be copied in a bounce buffer provided by the caller running
bpf_xdp_copy_buf().

BPF_F_XDP_HAS_FRAGS flag has been introduced to notify the kernel the
eBPF program fully support xdp frags.
SEC("xdp.frags"), SEC_DEF("xdp.frags/devmap") and SEC_DEF("xdp.frags/cpumap")
have been introduced to declare xdp frags support.
The NIC driver is expected to reject an eBPF program if it is running in
XDP frags mode and the program does not support XDP frags.
In the same way it is not possible to mix XDP frags and XDP legacy
programs in a CPUMAP/DEVMAP or tailcall a XDP frags/legacy program from
a legacy/frags one.

More info about the main idea behind this approach can be found here [1][2].

Changes since v22:
- remove leftover CHECK macro usage
- reintroduce SEC_XDP_FRAGS flag in sec_def_flags
- rename xdp multi_frags in xdp frags
- do not report xdp_frags support in fdinfo

Changes since v21:
- rename *_mb in *_frags: e.g:
  s/xdp_buff_is_mb/xdp_buff_has_frags
- rely on ASSERT_* and not on CHECK in
  bpf_xdp_load_bytes/bpf_xdp_store_bytes self-tests
- change new multi.frags SEC definitions to use the following schema:
  prog_type.prog_flags/attach_place
- get rid of unnecessary properties in new multi.frags SEC definitions
- rebase on top of bpf-next

Changes since v20:
- rebase to current bpf-next

Changes since v19:
- do not run deprecated bpf_prog_load()
- rely on skb_frag_size_add/skb_frag_size_sub in
  bpf_xdp_mb_increase_tail/bpf_xdp_mb_shrink_tail
- rely on sinfo->nr_frags in bpf_xdp_mb_shrink_tail to check if the frame has
  been shrunk to a single-buffer one
- allow XDP_REDIRECT of a xdp-mb frame into a CPUMAP

Changes since v18:
- fix bpf_xdp_copy_buf utility routine when we want to load/store data
  contained in frag<n>
- add a selftest for bpf_xdp_load_bytes/bpf_xdp_store_bytes when the caller
  accesses data contained in frag<n> and frag<n+1>

Changes since v17:
- rework bpf_xdp_copy to squash base and frag management
- remove unused variable in bpf_xdp_mb_shrink_tail()
- move bpf_xdp_copy_buf() out of bpf_xdp_pointer()
- add sanity check for len in bpf_xdp_pointer()
- remove EXPORT_SYMBOL for __xdp_return()
- introduce frag_size field in xdp_rxq_info to let the driver specify max value
  for xdp fragments. frag_size set to 0 means the tail increase of last the
  fragment is not supported.

Changes since v16:
- do not allow tailcalling a xdp multi-buffer/legacy program from a
  legacy/multi-buff one.
- do not allow mixing xdp multi-buffer and xdp legacy programs in a
  CPUMAP/DEVMAP
- add selftests for CPUMAP/DEVMAP xdp mb compatibility
- disable XDP_REDIRECT for xdp multi-buff for the moment
- set max offset value to 0xffff in bpf_xdp_pointer
- use ARG_PTR_TO_UNINIT_MEM and ARG_CONST_SIZE for arg3_type and arg4_type
  of bpf_xdp_store_bytes/bpf_xdp_load_bytes

Changes since v15:
- let the verifier check buf is not NULL in
  bpf_xdp_load_bytes/bpf_xdp_store_bytes helpers
- return an error if offset + length is over frame boundaries in
  bpf_xdp_pointer routine
- introduce BPF_F_XDP_MB flag for bpf_attr to notify the kernel the eBPF
  program fully supports xdp multi-buffer.
- reject a non XDP multi-buffer program if the driver is running in
  XDP multi-buffer mode.

Changes since v14:
- intrudce bpf_xdp_pointer utility routine and
  bpf_xdp_load_bytes/bpf_xdp_store_bytes helpers
- drop bpf_xdp_adjust_data helper
- drop xdp_frags_truesize in skb_shared_info
- explode bpf_xdp_mb_adjust_tail in bpf_xdp_mb_increase_tail and
  bpf_xdp_mb_shrink_tail

Changes since v13:
- use u32 for xdp_buff/xdp_frame flags field
- rename xdp_frags_tsize in xdp_frags_truesize
- fixed comments

Changes since v12:
- fix bpf_xdp_adjust_data helper for single-buffer use case
- return -EFAULT in bpf_xdp_adjust_{head,tail} in case the data pointers are not
  properly reset
- collect ACKs from John

Changes since v11:
- add missing static to bpf_xdp_get_buff_len_proto structure
- fix bpf_xdp_adjust_data helper when offset is smaller than linear area length.

Changes since v10:
- move xdp->data to the requested payload offset instead of to the beginning of
  the fragment in bpf_xdp_adjust_data()

Changes since v9:
- introduce bpf_xdp_adjust_data helper and related selftest
- add xdp_frags_size and xdp_frags_tsize fields in skb_shared_info
- introduce xdp_update_skb_shared_info utility routine in ordere to not reset
  frags array in skb_shared_info converting from a xdp_buff/xdp_frame to a skb
- simplify bpf_xdp_copy routine

Changes since v8:
- add proper dma unmapping if XDP_TX fails on mvneta for a xdp multi-buff
- switch back to skb_shared_info implementation from previous xdp_shared_info
  one
- avoid using a bietfield in xdp_buff/xdp_frame since it introduces performance
  regressions. Tested now on 10G NIC (ixgbe) to verify there are no performance
  penalties for regular codebase
- add bpf_xdp_get_buff_len helper and remove frame_length field in xdp ctx
- add data_len field in skb_shared_info struct
- introduce XDP_FLAGS_FRAGS_PF_MEMALLOC flag

Changes since v7:
- rebase on top of bpf-next
- fix sparse warnings
- improve comments for frame_length in include/net/xdp.h

Changes since v6:
- the main difference respect to previous versions is the new approach proposed
  by Eelco to pass full length of the packet to eBPF layer in XDP context
- reintroduce multi-buff support to eBPF kself-tests
- reintroduce multi-buff support to bpf_xdp_adjust_tail helper
- introduce multi-buffer support to bpf_xdp_copy helper
- rebase on top of bpf-next

Changes since v5:
- rebase on top of bpf-next
- initialize mb bit in xdp_init_buff() and drop per-driver initialization
- drop xdp->mb initialization in xdp_convert_zc_to_xdp_frame()
- postpone introduction of frame_length field in XDP ctx to another series
- minor changes

Changes since v4:
- rebase ontop of bpf-next
- introduce xdp_shared_info to build xdp multi-buff instead of using the
  skb_shared_info struct
- introduce frame_length in xdp ctx
- drop previous bpf helpers
- fix bpf_xdp_adjust_tail for xdp multi-buff
- introduce xdp multi-buff self-tests for bpf_xdp_adjust_tail
- fix xdp_return_frame_bulk for xdp multi-buff

Changes since v3:
- rebase ontop of bpf-next
- add patch 10/13 to copy back paged data from a xdp multi-buff frame to
  userspace buffer for xdp multi-buff selftests

Changes since v2:
- add throughput measurements
- drop bpf_xdp_adjust_mb_header bpf helper
- introduce selftest for xdp multibuffer
- addressed comments on bpf_xdp_get_frags_count
- introduce xdp multi-buff support to cpumaps

Changes since v1:
- Fix use-after-free in xdp_return_{buff/frame}
- Introduce bpf helpers
- Introduce xdp_mb sample program
- access skb_shared_info->nr_frags only on the last fragment

Changes since RFC:
- squash multi-buffer bit initialization in a single patch
- add mvneta non-linear XDP buff support for tx side

[0] https://netdevconf.info/0x14/session.html?talk-the-path-to-tcp-4k-mtu-and-rx-zerocopy
[1] https://github.com/xdp-project/xdp-project/blob/master/areas/core/xdp-multi-buffer01-design.org
[2] https://netdevconf.info/0x14/session.html?tutorial-add-XDP-support-to-a-NIC-driver (XDPmulti-buffers section)

Eelco Chaudron (3):
  bpf: add frags support to the bpf_xdp_adjust_tail() API
  bpf: add frags support to xdp copy helpers
  bpf: selftests: update xdp_adjust_tail selftest to include xdp frags

Lorenzo Bianconi (19):
  net: skbuff: add size metadata to skb_shared_info for xdp
  xdp: introduce flags field in xdp_buff/xdp_frame
  net: mvneta: update frags bit before passing the xdp buffer to eBPF
    layer
  net: mvneta: simplify mvneta_swbm_add_rx_fragment management
  net: xdp: add xdp_update_skb_shared_info utility routine
  net: marvell: rely on xdp_update_skb_shared_info utility routine
  xdp: add frags support to xdp_return_{buff/frame}
  net: mvneta: add frags support to XDP_TX
  bpf: introduce BPF_F_XDP_HAS_FRAGS flag in prog_flags loading the ebpf
    program
  net: mvneta: enable jumbo frames if the loaded XDP program support
    frags
  bpf: introduce bpf_xdp_get_buff_len helper
  bpf: move user_size out of bpf_test_init
  bpf: introduce frags support to bpf_prog_test_run_xdp()
  bpf: test_run: add xdp_shared_info pointer in bpf_test_finish
    signature
  libbpf: Add SEC name for xdp frags programs
  net: xdp: introduce bpf_xdp_pointer utility routine
  bpf: selftests: introduce bpf_xdp_{load,store}_bytes selftest
  bpf: selftests: add CPUMAP/DEVMAP selftests for xdp frags
  xdp: disable XDP_REDIRECT for xdp frags
====================

Signed-off-by: Alexei Starovoitov <ast@kernel.org>

xdp: disable XDP_REDIRECT for xdp frags

XDP_REDIRECT is not fully supported yet for xdp frags since not
all XDP capable drivers can map non-linear xdp_frame in ndo_xdp_xmit
so disable it for the moment.

Acked-by: Toke Hoiland-Jorgensen <toke@redhat.com>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://lore.kernel.org/r/0da25e117d0e2673f5d0ce6503393c55c6fb1be9.1642758637.git.lorenzo@kernel.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>