Mahesh Bandewar [Wed, 18 Jan 2017 23:02:55 +0000 (15:02 -0800)]
macvlan: use netdev_is_rx_handler_busy instead of checking specific type
netdev_is_rx_handler_busy() check is a superset of netif_is_ipvlan_port()
check and hence should be preferred.
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mahesh Bandewar [Wed, 18 Jan 2017 23:02:53 +0000 (15:02 -0800)]
ipvlan: use netdev_is_rx_handler_busy instead of checking specific type
IPvlan checks if the master device is already used by checking a
specific device (here it's macvlan device). This is technically not
sufficient and it should just ensure the rx_handler is busy or not.
This would be a super check that includes macvlan and any other that
has already registered rx-handler.
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mahesh Bandewar [Wed, 18 Jan 2017 23:02:49 +0000 (15:02 -0800)]
net: remove duplicate code.
netdev_rx_handler_register() checks to see if the handler is already
busy which was recently separated into netdev_is_rx_handler_busy(). So
use the same function inside register() to avoid code duplication.
Essentially this change should be a no-op
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Collins [Wed, 18 Jan 2017 21:04:28 +0000 (14:04 -0700)]
fq_codel: Avoid regenerating skb flow hash unless necessary
The fq_codel qdisc currently always regenerates the skb flow hash.
This wastes some cycles and prevents flow seperation in cases where
the traffic has been encrypted and can no longer be understood by the
flow dissector.
Change it to use the prexisting flow hash if one exists, and only
regenerate if necessary.
Signed-off-by: Andrew Collins <acollins@cradlepoint.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lance Richardson [Wed, 18 Jan 2017 20:24:57 +0000 (15:24 -0500)]
vxlan: preserve type of dst_port parm for encap_bypass_if_local()
Eliminate sparse warning by maintaining type of dst_port
as __be16.
Signed-off-by: Lance Richardson <lrichard@redhat.com>
Acked-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lance Richardson [Wed, 18 Jan 2017 20:14:56 +0000 (15:14 -0500)]
csum: eliminate sparse warning in remcsum_unadjust()
Cast second parameter of csum_sub() from __sum16 to __wsum.
Signed-off-by: Lance Richardson <lrichard@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 20 Jan 2017 17:10:17 +0000 (12:10 -0500)]
Merge branch 'tipc-multicast-through-replication'
Jon Maloy says:
====================
tipc: emulate multicast through replication
TIPC multicast messages are currently distributed via L2 broadcast
or IP multicast to all nodes in the cluster, irrespective of the
number of real destinations of the message.
In this series we introduce an option to transport messages via
replication ("replicast") across a selected number of unicast links,
instead of relying on the underlying media. This option is used when
true broadcast/multicast is not supported by the media, or when the
number of true destinations is much smaller than the cluster size.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jon Paul Maloy [Wed, 18 Jan 2017 18:50:53 +0000 (13:50 -0500)]
tipc: make replicast a user selectable option
If the bearer carrying multicast messages supports broadcast, those
messages will be sent to all cluster nodes, irrespective of whether
these nodes host any actual destinations socket or not. This is clearly
wasteful if the cluster is large and there are only a few real
destinations for the message being sent.
In this commit we extend the eligibility of the newly introduced
"replicast" transmit option. We now make it possible for a user to
select which method he wants to be used, either as a mandatory setting
via setsockopt(), or as a relative setting where we let the broadcast
layer decide which method to use based on the ratio between cluster
size and the message's actual number of destination nodes.
In the latter case, a sending socket must stick to a previously
selected method until it enters an idle period of at least 5 seconds.
This eliminates the risk of message reordering caused by method change,
i.e., when changes to cluster size or number of destinations would
otherwise mandate a new method to be used.
Reviewed-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jon Paul Maloy [Wed, 18 Jan 2017 18:50:52 +0000 (13:50 -0500)]
tipc: introduce replicast as transport option for multicast
TIPC multicast messages are currently carried over a reliable
'broadcast link', making use of the underlying media's ability to
transport packets as L2 broadcast or IP multicast to all nodes in
the cluster.
When the used bearer is lacking that ability, we can instead emulate
the broadcast service by replicating and sending the packets over as
many unicast links as needed to reach all identified destinations.
We now introduce a new TIPC link-level 'replicast' service that does
this.
Reviewed-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jon Paul Maloy [Wed, 18 Jan 2017 18:50:51 +0000 (13:50 -0500)]
tipc: add functionality to lookup multicast destination nodes
As a further preparation for the upcoming 'replicast' functionality,
we add some necessary structs and functions for looking up and returning
a list of all nodes that host destinations for a given multicast message.
Reviewed-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jon Paul Maloy [Wed, 18 Jan 2017 18:50:50 +0000 (13:50 -0500)]
tipc: add function for checking broadcast support in bearer
As a preparation for the 'replicast' functionality we are going to
introduce in the next commits, we need the broadcast base structure to
store whether bearer broadcast is available at all from the currently
used bearer or bearers.
We do this by adding a new function tipc_bearer_bcast_support() to
the bearer layer, and letting the bearer selection function in
bcast.c use this to give a new boolean field, 'bcast_support' the
appropriate value.
Reviewed-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Gianluca Borello [Wed, 18 Jan 2017 17:55:49 +0000 (17:55 +0000)]
bpf: add bpf_probe_read_str helper
Provide a simple helper with the same semantics of strncpy_from_unsafe():
int bpf_probe_read_str(void *dst, int size, const void *unsafe_addr)
This gives more flexibility to a bpf program. A typical use case is
intercepting a file name during sys_open(). The current approach is:
SEC("kprobe/sys_open")
void bpf_sys_open(struct pt_regs *ctx)
{
char buf[PATHLEN]; // PATHLEN is defined to 256
bpf_probe_read(buf, sizeof(buf), ctx->di);
/* consume buf */
}
This is suboptimal because the size of the string needs to be estimated
at compile time, causing more memory to be copied than often necessary,
and can become more problematic if further processing on buf is done,
for example by pushing it to userspace via bpf_perf_event_output(),
since the real length of the string is unknown and the entire buffer
must be copied (and defining an unrolled strnlen() inside the bpf
program is a very inefficient and unfeasible approach).
With the new helper, the code can easily operate on the actual string
length rather than the buffer size:
SEC("kprobe/sys_open")
void bpf_sys_open(struct pt_regs *ctx)
{
char buf[PATHLEN]; // PATHLEN is defined to 256
int res = bpf_probe_read_str(buf, sizeof(buf), ctx->di);
/* consume buf, for example push it to userspace via
* bpf_perf_event_output(), but this time we can use
* res (the string length) as event size, after checking
* its boundaries.
*/
}
Another useful use case is when parsing individual process arguments or
individual environment variables navigating current->mm->arg_start and
current->mm->env_start: using this helper and the return value, one can
quickly iterate at the right offset of the memory area.
The code changes simply leverage the already existent
strncpy_from_unsafe() kernel function, which is safe to be called from a
bpf program as it is used in bpf_trace_printk().
Signed-off-by: Gianluca Borello <g.borello@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 20 Jan 2017 16:43:17 +0000 (11:43 -0500)]
Merge branch 'bus-agnostic-num-vf'
Phil Sutter says:
====================
Retrieve number of VFs in a bus-agnostic way
Previously, it was assumed that only PCI NICs would be capable of having
virtual functions - with my proposed enhancement of dummy NIC driver
implementing (fake) ones for testing purposes, this is no longer true.
Discussion of said patch has led to the suggestion of implementing a
bus-agnostic method for VF count retrieval so rtnetlink could work with
both real VF-capable PCI NICs as well as my dummy modifications without
introducing ugly hacks.
The following series tries to achieve just that by introducing a bus
type callback to retrieve a device's number of VFs, implementing this
callback for PCI bus and finally adjusting rtnetlink to make use of the
generalized infrastructure.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Phil Sutter [Wed, 18 Jan 2017 13:04:39 +0000 (14:04 +0100)]
device: Implement a bus agnostic dev_num_vf routine
Now that pci_bus_type has num_vf callback set, dev_num_vf can be
implemented in a bus type independent way and the check for whether a
PCI device is being handled in rtnetlink can be dropped.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
Phil Sutter [Wed, 18 Jan 2017 13:04:38 +0000 (14:04 +0100)]
PCI: implement num_vf bus type callback
Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
Phil Sutter [Wed, 18 Jan 2017 13:04:37 +0000 (14:04 +0100)]
device: bus_type: Introduce num_vf callback
This allows for bus types to implement their own method of retrieving
the number of virtual functions a NIC on that type of bus supports.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
Geliang Tang [Fri, 20 Jan 2017 14:27:04 +0000 (22:27 +0800)]
sock: use hlist_entry_safe
Use hlist_entry_safe() instead of open-coding it.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Sitnicki [Fri, 20 Jan 2017 13:53:06 +0000 (14:53 +0100)]
gre6: Clean up unused struct ipv6_tel_txoption definition
Commit
b05229f44228 ("gre6: Cleanup GREv6 transmit path, call common GRE
functions") removed the ip6gre specific transmit function, but left the
struct ipv6_tel_txoption definition. Clean it up.
Signed-off-by: Jakub Sitnicki <jkbs@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 20 Jan 2017 13:06:08 +0000 (05:06 -0800)]
net: remove bh disabling around percpu_counter accesses
Shaohua Li made percpu_counter irq safe in commit
098faf5805c8
("percpu_counter: make APIs irq safe")
We can safely remove BH disable/enable sections around various
percpu_counter manipulations.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Arnd Bergmann [Wed, 18 Jan 2017 14:52:51 +0000 (15:52 +0100)]
cxgb4: hide unused warnings
The two new variables are only used inside of an #ifdef and cause
harmless warnings when that is disabled:
drivers/net/ethernet/chelsio/cxgb4/cxgb4_main.c: In function 'init_one':
drivers/net/ethernet/chelsio/cxgb4/cxgb4_main.c:4646:9: error: unused variable 'port_vec' [-Werror=unused-variable]
drivers/net/ethernet/chelsio/cxgb4/cxgb4_main.c:4646:6: error: unused variable 'v' [-Werror=unused-variable]
This adds another #ifdef around the declarations.
Fixes:
96fe11f27b70 ("cxgb4: Implement ndo_get_phys_port_id for mgmt dev")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Wed, 18 Jan 2017 15:40:36 +0000 (07:40 -0800)]
net: ipv6: Keep nexthop of multipath route on admin down
IPv6 deletes route entries associated with multipath routes on an
admin down where IPv4 does not. For example:
$ ip ro ls vrf red
unreachable default metric 8192
1.1.1.0/24 metric 64
nexthop via 10.100.1.254 dev eth1 weight 1
nexthop via 10.100.2.254 dev eth2 weight 1
10.100.1.0/24 dev eth1 proto kernel scope link src 10.100.1.4
10.100.2.0/24 dev eth2 proto kernel scope link src 10.100.2.4
$ ip -6 ro ls vrf red
2001:db8:1::/120 dev eth1 proto kernel metric 256 pref medium
2001:db8:2:: dev red proto none metric 0 pref medium
2001:db8:2::/120 dev eth2 proto kernel metric 256 pref medium
2001:db8:11::/120 via 2001:db8:1::16 dev eth1 metric 1024 pref medium
2001:db8:11::/120 via 2001:db8:2::17 dev eth2 metric 1024 pref medium
...
Set link down:
$ ip li set eth1 down
IPv4 retains the multihop route but flags eth1 route as dead:
$ ip ro ls vrf red
unreachable default metric 8192
1.1.1.0/24
nexthop via 10.100.1.16 dev eth1 weight 1 dead linkdown
nexthop via 10.100.2.16 dev eth2 weight 1
10.100.2.0/24 dev eth2 proto kernel scope link src 10.100.2.4
and IPv6 deletes the route as part of flushing all routes for the device:
$ ip -6 ro ls vrf red
2001:db8:2:: dev red proto none metric 0 pref medium
2001:db8:2::/120 dev eth2 proto kernel metric 256 pref medium
2001:db8:11::/120 via 2001:db8:2::17 dev eth2 metric 1024 pref medium
...
Worse, on admin up of the device the multipath route has to be deleted
to get this leg of the route re-added.
This patch keeps routes that are part of a multipath route if
ignore_routes_with_linkdown is set with the dead and linkdown flags
enabling consistency between IPv4 and IPv6:
$ ip -6 ro ls vrf red
2001:db8:2:: dev red proto none metric 0 pref medium
2001:db8:2::/120 dev eth2 proto kernel metric 256 pref medium
2001:db8:11::/120 via 2001:db8:1::16 dev eth1 metric 1024 dead linkdown pref medium
2001:db8:11::/120 via 2001:db8:2::17 dev eth2 metric 1024 pref medium
...
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Wed, 18 Jan 2017 04:14:10 +0000 (20:14 -0800)]
mlx4: support __GFP_MEMALLOC for rx
Commit
04aeb56a1732 ("net/mlx4_en: allocate non 0-order pages for RX
ring with __GFP_NOMEMALLOC") added code that appears to be not needed at
that time, since mlx4 never used __GFP_MEMALLOC allocations anyway.
As using memory reserves is a must in some situations (swap over NFS or
iSCSI), this patch adds this flag.
Note that this driver does not reuse pages (yet) so we do not have to
add anything else.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Cc: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Timur Tabi [Tue, 17 Jan 2017 22:31:19 +0000 (16:31 -0600)]
Revert "net: qcom/emac: configure the external phy to allow pause frames"
This reverts commit
3e884493448131179a5b7cae1ddca1028ffaecc8.
With commit
529ed1275263 ("net: phy: phy drivers should not set
SUPPORTED_[Asym_]Pause"), phylib now handles automatically enabling
pause frame support in the PHY, and the MAC driver should follow suit.
Since the EMAC driver driver does this, we no longer need to force
pause frames support.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Volodymyr Bendiuga [Thu, 19 Jan 2017 16:05:04 +0000 (17:05 +0100)]
phy: increase size of MII_BUS_ID_SIZE and bus_id
Some bus names are pretty long and do not fit into
17 chars. Increase therefore MII_BUS_ID_SIZE and
phy_fixup.bus_id to larger number. Now mii_bus.id
can host larger name.
Signed-off-by: Volodymyr Bendiuga <volodymyr.bendiuga@gmail.com>
Signed-off-by: Magnus Öberg <magnus.oberg@westermo.se>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrei.Pistirica@microchip.com [Thu, 19 Jan 2017 15:56:15 +0000 (17:56 +0200)]
macb: Common code to enable ptp support for MACB/GEM
This patch does the following:
- MACB/GEM-PTP interface
- registers and bitfields for TSU
- capability flags to enable PTP per platform basis
Signed-off-by: Andrei Pistirica <andrei.pistirica@microchip.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tobias Klauser [Thu, 19 Jan 2017 15:04:25 +0000 (16:04 +0100)]
net: caif: Remove unused stats member from struct chnl_net
The stats member of struct chnl_net is used nowhere in the code, so it
might as well be removed.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Arnd Bergmann [Thu, 19 Jan 2017 09:45:31 +0000 (10:45 +0100)]
net/sched: cls_flower: reduce fl_change stack size
The new ARP support has pushed the stack size over the edge on ARM,
as there are two large objects on the stack in this function (mask
and tb) and both have now grown a bit more:
net/sched/cls_flower.c: In function 'fl_change':
net/sched/cls_flower.c:928:1: error: the frame size of 1072 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
We can solve this by dynamically allocating one or both of them.
I first tried to do it just for the mask, but that only saved
152 bytes on ARM, while this version just does it for the 'tb'
array, bringing the stack size back down to 664 bytes.
Fixes:
99d31326cbe6 ("net/sched: cls_flower: Support matching on ARP")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tobias Klauser [Wed, 18 Jan 2017 16:45:01 +0000 (17:45 +0100)]
net: Remove usage of net_device last_rx member
The network stack no longer uses the last_rx member of struct net_device
since the bonding driver switched to use its own private last_rx in
commit
9f242738376d ("bonding: use last_arp_rx in slave_last_rx()").
However, some drivers still (ab)use the field for their own purposes and
some driver just update it without actually using it.
Previously, there was an accompanying comment for the last_rx member
added in commit
4dc89133f49b ("net: add a comment on netdev->last_rx")
which asked drivers not to update is, unless really needed. However,
this commend was removed in commit
f8ff080dacec ("bonding: remove
useless updating of slave->dev->last_rx"), so some drivers added later
on still did update last_rx.
Remove all usage of last_rx and switch three drivers (sky2, atp and
smc91c92_cs) which actually read and write it to use their own private
copy in netdev_priv.
Compile-tested with allyesconfig and allmodconfig on x86 and arm.
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Jay Vosburgh <j.vosburgh@gmail.com>
Cc: Veaceslav Falico <vfalico@gmail.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Cc: Mirko Lindner <mlindner@marvell.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot [Wed, 18 Jan 2017 01:41:39 +0000 (20:41 -0500)]
net: dsa: use cpu_switch instead of ds[0]
Now that the DSA Ethernet switches are true Linux devices, the CPU
switch is not necessarily the first one. If its address is higher than
the second switch on the same MDIO bus, its index will be 1, not 0.
Avoid any confusion by using dst->cpu_switch instead of dst->ds[0].
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot [Wed, 18 Jan 2017 01:41:38 +0000 (20:41 -0500)]
net: dsa: store CPU switch structure in the tree
Store a dsa_switch pointer to the CPU switch in the tree instead of only
its index. This avoids the need to initialize it to -1.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ivan Khoronzhuk [Wed, 18 Jan 2017 00:28:06 +0000 (02:28 +0200)]
net: ethernet: ti: davinci_cpdma: correct check on NULL in set rate
Check "ch" on NULL first, then get ctlr.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 18 Jan 2017 21:35:30 +0000 (16:35 -0500)]
Merge branch 'vhost_net-batching'
Jason Wang says:
====================
vhost_net tx batching
This series tries to implement tx batching support for vhost. This was
done by using MSG_MORE as a hint for under layer socket. The backend
(e.g tap) can then batch the packets temporarily in a list and
submit it all once the number of bacthed exceeds a limitation.
Tests shows obvious improvement on guest pktgen over over
mlx4(noqueue) on host:
Mpps -+%
rx-frames = 0 0.91 +0%
rx-frames = 4 1.00 +9.8%
rx-frames = 8 1.00 +9.8%
rx-frames = 16 1.01 +10.9%
rx-frames = 32 1.07 +17.5%
rx-frames = 48 1.07 +17.5%
rx-frames = 64 1.08 +18.6%
rx-frames = 64 (no MSG_MORE) 0.91 +0%
Changes from V4:
- stick to NAPI_POLL_WEIGHT for rx-frames is user specify a value
greater than it.
Changes from V3:
- use ethtool instead of module parameter to control the maximum
number of batched packets
- avoid overhead when MSG_MORE were not set and no packet queued
Changes from V2:
- remove uselss queue limitation check (and we don't drop any packet now)
Changes from V1:
- drop NAPI handler since we don't use NAPI now
- fix the issues that may exceeds max pending of zerocopy
- more improvement on available buffer detection
- move the limitation of batched pacekts from vhost to tuntap
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jason Wang [Wed, 18 Jan 2017 07:02:03 +0000 (15:02 +0800)]
tun: rx batching
We can only process 1 packet at one time during sendmsg(). This often
lead bad cache utilization under heavy load. So this patch tries to do
some batching during rx before submitting them to host network
stack. This is done through accepting MSG_MORE as a hint from
sendmsg() caller, if it was set, batch the packet temporarily in a
linked list and submit them all once MSG_MORE were cleared.
Tests were done by pktgen (burst=128) in guest over mlx4(noqueue) on host:
Mpps -+%
rx-frames = 0 0.91 +0%
rx-frames = 4 1.00 +9.8%
rx-frames = 8 1.00 +9.8%
rx-frames = 16 1.01 +10.9%
rx-frames = 32 1.07 +17.5%
rx-frames = 48 1.07 +17.5%
rx-frames = 64 1.08 +18.6%
rx-frames = 64 (no MSG_MORE) 0.91 +0%
User were allowed to change per device batched packets through
ethtool -C rx-frames. NAPI_POLL_WEIGHT were used as upper limitation
to prevent bh from being disabled too long.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jason Wang [Wed, 18 Jan 2017 07:02:02 +0000 (15:02 +0800)]
vhost_net: tx batching
This patch tries to utilize tuntap rx batching by peeking the tx
virtqueue during transmission, if there's more available buffers in
the virtqueue, set MSG_MORE flag for a hint for backend (e.g tuntap)
to batch the packets.
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jason Wang [Wed, 18 Jan 2017 07:02:01 +0000 (15:02 +0800)]
vhost: better detection of available buffers
This patch tries to do several tweaks on vhost_vq_avail_empty() for a
better performance:
- check cached avail index first which could avoid userspace memory access.
- using unlikely() for the failure of userspace access
- check vq->last_avail_idx instead of cached avail index as the last
step.
This patch is need for batching supports which needs to peek whether
or not there's still available buffers in the ring.
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mao Wenan [Wed, 18 Jan 2017 00:50:05 +0000 (08:50 +0800)]
net:add one common config ARCH_WANT_RELAX_ORDER to support relax ordering
Relax ordering(RO) is one feature of 82599 NIC, to enable this feature can
enhance the performance for some cpu architecure, such as SPARC and so on.
Currently it only supports one special cpu architecture(SPARC) in 82599
driver to enable RO feature, this is not very common for other cpu architecture
which really needs RO feature.
This patch add one common config CONFIG_ARCH_WANT_RELAX_ORDER to set RO feature,
and should define CONFIG_ARCH_WANT_RELAX_ORDER in sparc Kconfig firstly.
Signed-off-by: Mao Wenan <maowenan@huawei.com>
Reviewed-by: Alexander Duyck <alexander.duyck@gmail.com>
Reviewed-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 18 Jan 2017 20:44:00 +0000 (15:44 -0500)]
Merge branch 'ipv6-simplify-rt6_fill_node'
David Ahern says:
====================
net: ipv6: simplify rt6_fill_node
Remove a couple of unnecessary input arguments to rt6_fill_node.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Tue, 17 Jan 2017 23:51:08 +0000 (15:51 -0800)]
net: ipv6: remove prefix arg to rt6_fill_node
The prefix arg to rt6_fill_node is non-0 in only 1 path - rt6_dump_route
where a user is requesting a prefix only dump. Simplify rt6_fill_node
by removing the prefix arg and moving the prefix check to rt6_dump_route.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Tue, 17 Jan 2017 23:51:07 +0000 (15:51 -0800)]
net: ipv6: remove nowait arg to rt6_fill_node
All callers of rt6_fill_node pass 0 for nowait arg. Remove the arg and
simplify rt6_fill_node accordingly.
rt6_fill_node passes the nowait of 0 to ip6mr_get_route. Remove the
nowait arg from it as well.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 18 Jan 2017 19:55:11 +0000 (14:55 -0500)]
Merge branch 'sctp-sender-side-stream-reconf-ssn-reset-request-chunk'
Xin Long says:
====================
sctp: add sender-side procedures for stream reconf ssn reset request chunk
Patch 6/6 is to implement sender-side procedures for the Outgoing
and Incoming SSN Reset Request Parameter described in rfc6525
section 5.1.2 and 5.1.3
Patches 1-5/6 are ahead of it to define some apis and asoc members
for it.
Note that with this patchset, asoc->reconf_enable has no chance yet to
be set, until the patch "sctp: add get and set sockopt for reconf_enable"
is applied in the future. As we can not just enable it when sctp is not
capable of processing reconf chunk yet.
v1->v2:
- put these into a smaller group.
- rename some temporary variables in the codes.
- rename the titles of the commits and improve some changelogs.
v2->v3:
- re-split the patchset and make sure it has no dead codes for review.
v3->v4:
- move sctp_make_reconf() into patch 1/6 to avoid kbuild warning.
- drop unused struct sctp_strreset_req.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long [Tue, 17 Jan 2017 16:44:47 +0000 (00:44 +0800)]
sctp: implement sender-side procedures for SSN Reset Request Parameter
This patch is to implement sender-side procedures for the Outgoing
and Incoming SSN Reset Request Parameter described in rfc6525 section
5.1.2 and 5.1.3.
It is also add sockopt SCTP_RESET_STREAMS in rfc6525 section 6.3.2
for users.
Note that the new asoc member strreset_outstanding is to make sure
only one reconf request chunk on the fly as rfc6525 section 5.1.1
demands.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long [Tue, 17 Jan 2017 16:44:46 +0000 (00:44 +0800)]
sctp: add sockopt SCTP_ENABLE_STREAM_RESET
This patch is to add sockopt SCTP_ENABLE_STREAM_RESET to get/set
strreset_enable to indicate which reconf request type it supports,
which is described in rfc6525 section 6.3.1.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long [Tue, 17 Jan 2017 16:44:45 +0000 (00:44 +0800)]
sctp: add reconf_enable in asoc ep and netns
This patch is to add reconf_enable field in all of asoc ep and netns
to indicate if they support stream reset.
When initializing, asoc reconf_enable get the default value from ep
reconf_enable which is from netns netns reconf_enable by default.
It is also to add reconf_capable in asoc peer part to know if peer
supports reconf_enable, the value is set if ext params have reconf
chunk support when processing init chunk, just as rfc6525 section
5.1.1 demands.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long [Tue, 17 Jan 2017 16:44:44 +0000 (00:44 +0800)]
sctp: add stream reconf primitive
This patch is to add a primitive based on sctp primitive frame for
sending stream reconf request. It works as the other primitives,
and create a SCTP_CMD_REPLY command to send the request chunk out.
sctp_primitive_RECONF would be the api to send a reconf request
chunk.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long [Tue, 17 Jan 2017 16:44:43 +0000 (00:44 +0800)]
sctp: add stream reconf timer
This patch is to add a per transport timer based on sctp timer frame
for stream reconf chunk retransmission. It would start after sending
a reconf request chunk, and stop after receiving the response chunk.
If the timer expires, besides retransmitting the reconf request chunk,
it would also do the same thing with data RTO timer. like to increase
the appropriate error counts, and perform threshold management, possibly
destroying the asoc if sctp retransmission thresholds are exceeded, just
as section 5.1.1 describes.
This patch is also to add asoc strreset_chunk, it is used to save the
reconf request chunk, so that it can be retransmitted, and to check if
the response is really for this request by comparing the information
inside with the response chunk as well.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long [Tue, 17 Jan 2017 16:44:42 +0000 (00:44 +0800)]
sctp: add support for generating stream reconf ssn reset request chunk
This patch is to add asoc strreset_outseq and strreset_inseq for
saving the reconf request sequence, initialize them when create
assoc and process init, and also to define Incoming and Outgoing
SSN Reset Request Parameter described in rfc6525 section 4.1 and
4.2, As they can be in one same chunk as section rfc6525 3.1-3
describes, it makes them in one function.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 18 Jan 2017 18:04:30 +0000 (13:04 -0500)]
Merge branch 'rework-inet_csk_get_port'
Josef Bacik says:
====================
Rework inet_csk_get_port
V3->V4:
-Removed the random include of addrconf.h that is no longer needed.
V2->V3:
-Dropped the fastsock from the tb and instead just carry the saddrs, family, and
ipv6 only flag.
-Reworked the helper functions to deal with this change so I could still use
them when checking the fast path.
-Killed tb->num_owners as per Eric's request.
-Attached a reproducer to the bottom of this email.
V1->V2:
-Added a new patch 'inet: collapse ipv4/v6 rcv_saddr_equal functions into one'
at Hannes' suggestion.
-Dropped ->bind_conflict and just use the new helper.
-Fixed a compile bug from the original ->bind_conflict patch.
The original description of the series follows:
At some point recently the guys working on our load balancer added the ability
to use SO_REUSEPORT. When they restarted their app with this option enabled
they immediately hit a softlockup on what appeared to be the
inet_bind_bucket->lock. Eventually what all of our debugging and discussion led
us to was the fact that the application comes up without SO_REUSEPORT, shuts
down which creates around 100k twsk's, and then comes up and tries to open a
bunch of sockets using SO_REUSEPORT, which meant traversing the inet_bind_bucket
owners list under the lock. Since this lock is needed for dealing with the
twsk's and basically anything else related to connections we would softlockup,
and sometimes not ever recover.
To solve this problem I did what you see in Path 5/5. Once we have a
SO_REUSEPORT socket on the tb->owners list we know that the socket has no
conflicts with any of the other sockets on that list. So we can add a copy of
the sock_common (really all we need is the recv_saddr but it seemed ugly to copy
just the ipv6, ipv4, and flag to indicate if we were ipv6 only in there so I've
copied the whole common) in order to check subsequent SO_REUSEPORT sockets. If
they match the previous one then we can skip the expensive
inet_csk_bind_conflict check. This is what eliminated the soft lockup that we
were seeing.
Patches 1-4 are cleanups and re-workings. For instance when we specify port ==
0 we need to find an open port, but we would do two passes through
inet_csk_bind_conflict every time we found a possible port. We would also keep
track of the smallest_port value in order to try and use it if we found no
port our first run through. This however made no sense as it would have had to
fail the first pass through inet_csk_bind_conflict, so would not actually pass
the second pass through either. Finally I split the function into two functions
in order to make it easier to read and to distinguish between the two behaviors.
I have tested this on one of our load balancing boxes during peak traffic and it
hasn't fallen over. But this is not my area, so obviously feel free to point
out where I'm being stupid and I'll get it fixed up and retested. Thanks,
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Josef Bacik [Tue, 17 Jan 2017 15:51:06 +0000 (07:51 -0800)]
inet: reset tb->fastreuseport when adding a reuseport sk
If we have non reuseport sockets on a tb we will set tb->fastreuseport to 0 and
never set it again. Which means that in the future if we end up adding a bunch
of reuseport sk's to that tb we'll have to do the expensive scan every time.
Instead add the ipv4/ipv6 saddr fields to the bind bucket, as well as the family
so we know what comparison to make, and the ipv6 only setting so we can make
sure to compare with new sockets appropriately. Once one sk has made it onto
the list we know that there are no potential bind conflicts on the owners list
that match that sk's rcv_addr. So copy the sk's information into our bind
bucket and set tb->fastruseport to FASTREUSESOCK_STRICT so we know we have to do
an extra check for subsequent reuseport sockets and skip the expensive bind
conflict check.
Signed-off-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Josef Bacik [Tue, 17 Jan 2017 15:51:05 +0000 (07:51 -0800)]
inet: split inet_csk_get_port into two functions
inet_csk_get_port does two different things, it either scans for an open port,
or it tries to see if the specified port is available for use. Since these two
operations have different rules and are basically independent lets split them
into two different functions to make them both more readable.
Signed-off-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Josef Bacik [Tue, 17 Jan 2017 15:51:04 +0000 (07:51 -0800)]
inet: don't check for bind conflicts twice when searching for a port
This is just wasted time, we've already found a tb that doesn't have a bind
conflict, and we don't drop the head lock so scanning again isn't going to give
us a different answer. Instead move the tb->reuse setting logic outside of the
found_tb path and put it in the success: path. Then make it so that we don't
goto again if we find a bind conflict in the found_tb path as we won't reach
this anymore when we are scanning for an ephemeral port.
Signed-off-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Josef Bacik [Tue, 17 Jan 2017 15:51:03 +0000 (07:51 -0800)]
inet: kill smallest_size and smallest_port
In inet_csk_get_port we seem to be using smallest_port to figure out where the
best place to look for a SO_REUSEPORT sk that matches with an existing set of
SO_REUSEPORT's. However if we get to the logic
if (smallest_size != -1) {
port = smallest_port;
goto have_port;
}
we will do a useless search, because we would have already done the
inet_csk_bind_conflict for that port and it would have returned 1, otherwise we
would have gone to found_tb and succeeded. Since this logic makes us do yet
another trip through inet_csk_bind_conflict for a port we know won't work just
delete this code and save us the time.
Signed-off-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Josef Bacik [Tue, 17 Jan 2017 15:51:02 +0000 (07:51 -0800)]
inet: drop ->bind_conflict
The only difference between inet6_csk_bind_conflict and inet_csk_bind_conflict
is how they check the rcv_saddr, so delete this call back and simply
change inet_csk_bind_conflict to call inet_rcv_saddr_equal.
Signed-off-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Josef Bacik [Tue, 17 Jan 2017 15:51:01 +0000 (07:51 -0800)]
inet: collapse ipv4/v6 rcv_saddr_equal functions into one
We pass these per-protocol equal functions around in various places, but
we can just have one function that checks the sk->sk_family and then do
the right comparison function. I've also changed the ipv4 version to
not cast to inet_sock since it is unneeded.
Signed-off-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
jpinto [Tue, 17 Jan 2017 14:53:07 +0000 (14:53 +0000)]
stmicro: add more information to Kconfig
This patch adds more info to stmicro' Kconfig files in order to be clearer
that the driver can be used by ethernet cards based on 10/100/1000/EQOS
Synopsys IP Cores.
EQOS was also added stmmac/Kconfig Kconfig, since dwmac4 is in fact EQoS,
one of Synopsys Ethernet IPs. More info at:
https://www.synopsys.com/dw/ipdir.php?ds=dwc_ether_qos
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Martin KaFai Lau [Wed, 18 Jan 2017 06:06:07 +0000 (22:06 -0800)]
net/mlx5e: Support bpf_xdp_adjust_head()
This patch adds bpf_xdp_adjust_head() support to mlx5e.
1. rx_headroom is added to struct mlx5e_rq. It uses
an existing 4 byte hole in the struct.
2. The adjusted data length is checked against
MLX5E_XDP_MIN_INLINE and MLX5E_SW2HW_MTU(rq->netdev->mtu).
3. The macro MLX5E_SW2HW_MTU is moved from en_main.c to en.h.
MLX5E_HW2SW_MTU is also moved to en.h for symmetric reason
but it is not a must.
v2:
- Keep the xdp specific logic in mlx5e_xdp_handle()
- Update dma_len after the sanity checks in mlx5e_xmit_xdp_frame()
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jason Baron [Tue, 17 Jan 2017 18:37:19 +0000 (13:37 -0500)]
tcp: accept RST for rcv_nxt - 1 after receiving a FIN
Using a Mac OSX box as a client connecting to a Linux server, we have found
that when certain applications (such as 'ab'), are abruptly terminated
(via ^C), a FIN is sent followed by a RST packet on tcp connections. The
FIN is accepted by the Linux stack but the RST is sent with the same
sequence number as the FIN, and Linux responds with a challenge ACK per
RFC 5961. The OSX client then sometimes (they are rate-limited) does not
reply with any RST as would be expected on a closed socket.
This results in sockets accumulating on the Linux server left mostly in
the CLOSE_WAIT state, although LAST_ACK and CLOSING are also possible.
This sequence of events can tie up a lot of resources on the Linux server
since there may be a lot of data in write buffers at the time of the RST.
Accepting a RST equal to rcv_nxt - 1, after we have already successfully
processed a FIN, has made a significant difference for us in practice, by
freeing up unneeded resources in a more expedient fashion.
A packetdrill test demonstrating the behavior:
// testing mac osx rst behavior
// Establish a connection
0.000 socket(..., SOCK_STREAM, IPPROTO_TCP) = 3
0.000 setsockopt(3, SOL_SOCKET, SO_REUSEADDR, [1], 4) = 0
0.000 bind(3, ..., ...) = 0
0.000 listen(3, 1) = 0
0.100 < S 0:0(0) win 32768 <mss 1460,nop,wscale 10>
0.100 > S. 0:0(0) ack 1 <mss 1460,nop,wscale 5>
0.200 < . 1:1(0) ack 1 win 32768
0.200 accept(3, ..., ...) = 4
// Client closes the connection
0.300 < F. 1:1(0) ack 1 win 32768
// now send rst with same sequence
0.300 < R. 1:1(0) ack 1 win 32768
// make sure we are in TCP_CLOSE
0.400 %{
assert tcpi_state == 7
}%
Signed-off-by: Jason Baron <jbaron@akamai.com>
Cc: Eric Dumazet <edumazet@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tobias Klauser [Tue, 17 Jan 2017 14:01:08 +0000 (15:01 +0100)]
net: ethoc: Make needlessly global struct ethtool_ops static
Make the needlessly global struct ethtool_ops ethoc_ethtool_ops static
to fix a sparse warning.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 17 Jan 2017 20:49:52 +0000 (15:49 -0500)]
Merge branch 'sfc-RX-hash-config'
Edward Cree says:
====================
sfc: RX hash configuration
This series improves support for getting and setting RX hashing
configuration on Solarflare adapters through ethtool.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Edward Cree [Tue, 17 Jan 2017 12:02:12 +0000 (12:02 +0000)]
sfc: read back RX hash config from the NIC when querying it with ethtool -x
Ensures that we report the key and indirection table the NIC is using,
rather than (if setting them failed earlier) what we wanted it to use.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Edward Cree [Tue, 17 Jan 2017 12:01:53 +0000 (12:01 +0000)]
sfc: support setting RSS hash key through ethtool API
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ganesh Goudar [Tue, 17 Jan 2017 08:39:38 +0000 (14:09 +0530)]
cxgb4: Implement ndo_get_phys_port_id for mgmt dev
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Gao Feng [Tue, 17 Jan 2017 02:21:19 +0000 (10:21 +0800)]
net: ping: Use right format specifier to avoid type casting
The inet_num is u16, so use %hu instead of casting it to int. And
the sk_bound_dev_if is int actually, so it needn't cast to int.
Signed-off-by: Gao Feng <fgao@ikuai8.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Shyam Saini [Tue, 17 Jan 2017 02:05:04 +0000 (07:35 +0530)]
qed: Replace memset with eth_zero_addr
Use eth_zero_addr to assign zero address to the given address array
instead of memset when the second argument in memset is address
of zero. Also, it makes the code clearer
Signed-off-by: Shyam Saini <mayhs11saini@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lance Richardson [Mon, 16 Jan 2017 23:11:35 +0000 (18:11 -0500)]
bridge: sparse fixes in br_ip6_multicast_alloc_query()
Changed type of csum field in struct igmpv3_query from __be16 to
__sum16 to eliminate type warning, made same change in struct
igmpv3_report for consistency.
Fixed up an ntohs() where htons() should have been used instead.
Signed-off-by: Lance Richardson <lrichard@redhat.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 17 Jan 2017 20:19:37 +0000 (15:19 -0500)]
Merge git://git./linux/kernel/git/davem/net
David S. Miller [Tue, 17 Jan 2017 19:38:44 +0000 (14:38 -0500)]
Merge branch 'mpls-packet-stats'
Robert Shearman says:
====================
mpls: Packet stats
This patchset records per-interface packet stats in the MPLS
forwarding path and exports them using a nest of attributes root at a
new IFLA_STATS_AF_SPEC attribute as part of RTM_GETSTATS messages:
[IFLA_STATS_AF_SPEC]
-> [AF_MPLS]
-> [MPLS_STATS_LINK]
-> struct mpls_link_stats
The first patch adds the rtnl infrastructure for this, including a new
callbacks to per-AF ops of fill_stats_af and get_stats_af_size. The
second patch records MPLS stats and makes use of the infrastructure to
export them. The rtnl infrastructure could also be used to export IPv6
stats in the future.
Changes in v2:
- make incrementing IPv6 stats in mpls_stats_inc_outucastpkts
conditional on CONFIG_IPV6 to fix build with CONFIG_IPV6=n
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Robert Shearman [Mon, 16 Jan 2017 14:16:37 +0000 (14:16 +0000)]
mpls: Packet stats
Having MPLS packet stats is useful for observing network operation and
for diagnosing network problems. In the absence of anything better,
RFC2863 and RFC3813 are used for guidance for which stats to expose
and the semantics of them. In particular rx_noroutes maps to in
unknown protos in RFC2863. The stats are exposed to userspace via
AF_MPLS attributes embedded in the IFLA_STATS_AF_SPEC attribute of
RTM_GETSTATS messages.
All the introduced fields are 64-bit, even error ones, to ensure no
overflow with long uptimes. Per-CPU counters are used to avoid
cache-line contention on the commonly used fields. The other fields
have also been made per-CPU for code to avoid performance problems in
error conditions on the assumption that on some platforms the cost of
atomic operations could be more expensive than sending the packet
(which is what would be done in the success case). If that's not the
case, we could instead not use per-CPU counters for these fields.
Only unicast and non-fragment are exposed at the moment, but other
counters can be exposed in the future either by adding to the end of
struct mpls_link_stats or by additional netlink attributes in the
AF_MPLS IFLA_STATS_AF_SPEC nested attribute.
Signed-off-by: Robert Shearman <rshearma@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Robert Shearman [Mon, 16 Jan 2017 14:16:36 +0000 (14:16 +0000)]
net: AF-specific RTM_GETSTATS attributes
Add the functionality for including address-family-specific per-link
stats in RTM_GETSTATS messages. This is done through adding a new
IFLA_STATS_AF_SPEC attribute under which address family attributes are
nested and then the AF-specific attributes can be further nested. This
follows the model of IFLA_AF_SPEC on RTM_*LINK messages and it has the
advantage of presenting an easily extended hierarchy. The rtnl_af_ops
structure is extended to provide AFs with the opportunity to fill and
provide the size of their stats attributes.
One alternative would have been to provide AFs with the ability to add
attributes directly into the RTM_GETSTATS message without a nested
hierarchy. I discounted this approach as it increases the rate at
which the 32 attribute number space is used up and it makes
implementation a little more tricky for stats dump resuming (at the
moment the order in which attributes are added to the message has to
match the numeric order of the attributes).
Another alternative would have been to register per-AF RTM_GETSTATS
handlers. I discounted this approach as I perceived a common use-case
to be getting all the stats for an interface and this approach would
necessitate multiple requests/dumps to retrieve them all.
Signed-off-by: Robert Shearman <rshearma@brocade.com>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julia Lawall [Tue, 17 Jan 2017 11:23:21 +0000 (12:23 +0100)]
stmmac: add missing of_node_put
The function stmmac_dt_phy provides several possibilities for initializing
plat->mdio_node, all of which have the effect of increasing the reference
count of the assigned value. This field is not updated elsewhere, so the
value is live until the end of the lifetime of plat (devm_allocated), just
after the end of stmmac_remove_config_dt. Thus, add an of_node_put on
plat->mdio_node in stmmac_remove_config_dt. It is possible that the field
mdio_node is never initialized, but of_node_put is NULL-safe, so it is also
safe to call of_node_put in that case.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rolf Neugebauer [Tue, 17 Jan 2017 18:13:51 +0000 (18:13 +0000)]
virtio: don't set VIRTIO_NET_HDR_F_DATA_VALID on xmit
This patch part reverts
fd2a0437dc33 and
e858fae2b0b8 which introduced a
subtle change in how the virtio_net flags are derived from the SKBs
ip_summed field.
With the above commits, the flags are set to VIRTIO_NET_HDR_F_DATA_VALID
when ip_summed == CHECKSUM_UNNECESSARY, thus treating it differently to
ip_summed == CHECKSUM_NONE, which should be the same.
Further, the virtio spec 1.0 / CS04 explicitly says that
VIRTIO_NET_HDR_F_DATA_VALID must not be set by the driver.
Fixes:
fd2a0437dc33 ("virtio_net: introduce virtio_net_hdr_{from,to}_skb")
Fixes:
e858fae2b0b8 (" virtio_net: use common code for virtio_net_hdr and skb GSO conversion")
Signed-off-by: Rolf Neugebauer <rolf.neugebauer@docker.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Tue, 17 Jan 2017 17:33:10 +0000 (09:33 -0800)]
Merge git://git./linux/kernel/git/davem/net
Pull networking fixes from David Miller:
1) Handle multicast packets properly in fast-RX path of mac80211, from
Johannes Berg.
2) Because of a logic bug, the user can't actually force SW
checksumming on r8152 devices. This makes diagnosis of hw
checksumming bugs really annoying. Fix from Hayes Wang.
3) VXLAN route lookup does not take the source and destination ports
into account, which means IPSEC policies cannot be matched properly.
Fix from Martynas Pumputis.
4) Do proper RCU locking in netvsc callbacks, from Stephen Hemminger.
5) Fix SKB leaks in mlxsw driver, from Arkadi Sharshevsky.
6) If lwtunnel_fill_encap() fails, we do not abort the netlink message
construction properly in fib_dump_info(), from David Ahern.
7) Do not use kernel stack for DMA buffers in atusb driver, from Stefan
Schmidt.
8) Openvswitch conntack actions need to maintain a correct checksum,
fix from Lance Richardson.
9) ax25_disconnect() is missing a check for ax25->sk being NULL, in
fact it already checks this, but not in all of the necessary spots.
Fix from Basil Gunn.
10) Action GET operations in the packet scheduler can erroneously bump
the reference count of the entry, making it unreleasable. Fix from
Jamal Hadi Salim. Jamal gives a great set of example command lines
that trigger this in the commit message.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (46 commits)
net sched actions: fix refcnt when GETing of action after bind
net/mlx4_core: Eliminate warning messages for SRQ_LIMIT under SRIOV
net/mlx4_core: Fix when to save some qp context flags for dynamic VST to VGT transitions
net/mlx4_core: Fix racy CQ (Completion Queue) free
net: stmmac: don't use netdev_[dbg, info, ..] before net_device is registered
net/mlx5e: Fix a -Wmaybe-uninitialized warning
ax25: Fix segfault after sock connection timeout
bpf: rework prog_digest into prog_tag
tipc: allocate user memory with GFP_KERNEL flag
net: phy: dp83867: allow RGMII_TXID/RGMII_RXID interface types
ip6_tunnel: Account for tunnel header in tunnel MTU
mld: do not remove mld souce list info when set link down
be2net: fix MAC addr setting on privileged BE3 VFs
be2net: don't delete MAC on close on unprivileged BE3 VFs
be2net: fix status check in be_cmd_pmac_add()
cpmac: remove hopeless #warning
ravb: do not use zero-length alignment DMA descriptor
mlx4: do not call napi_schedule() without care
openvswitch: maintain correct checksum state in conntrack actions
tcp: fix tcp_fastopen unaligned access complaints on sparc
...
Linus Torvalds [Tue, 17 Jan 2017 17:27:50 +0000 (09:27 -0800)]
Merge branch 'stable/for-linus-4.10' of git://git./linux/kernel/git/konrad/swiotlb
Pull swiotlb fix from Konrad Rzeszutek Wilk:
"A tiny fix to make sure that page-sized mappings are page-aligned (and
not say straddle two pages). This is important for some drivers (such
as NVME)"
* 'stable/for-linus-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/swiotlb:
swiotlb: ensure that page-sized mappings are page-aligned
Linus Torvalds [Tue, 17 Jan 2017 17:08:19 +0000 (09:08 -0800)]
Merge tag 'mmc-v4.10-rc3' of git://git./linux/kernel/git/ulfh/mmc
Pull MMC fixes from Ulf Hansson:
"MMC core:
- fix regressions detecting HS/HS DDR eMMC cards related to CMD6
MMC host:
- mmc: mxs-mmc: Fix additional cycles after transmission stop
- sdhci-acpi: Only powered up enabled acpi child devices
- meson: avoid possible NULL dereference"
* tag 'mmc-v4.10-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
mmc: core: Restore parts of the polling policy when switch to HS/HS DDR
mmc: mxs-mmc: Fix additional cycles after transmission stop
mmc: sdhci-acpi: Only powered up enabled acpi child devices
MMC: meson: avoid possible NULL dereference
Linus Torvalds [Tue, 17 Jan 2017 16:50:59 +0000 (08:50 -0800)]
Merge tag 'for-linus-
20170116' of git://git.infradead.org/linux-mtd
Pull MTD fixes from Brian Norris:
"Just NAND updates from Boris:
- avoid compiling xway NAND controller driver as a module (which
didn't work)
- fix tango NAND DT binding and make sure the controller is in a
clean state at probe time
- add dependency on HAS_IOMEM to the oxnas NAND driver
- fix irq number validity check in the lpc32xx driver"
* tag 'for-linus-
20170116' of git://git.infradead.org/linux-mtd:
mtd: nand: lpc32xx: fix invalid error handling of a requested irq
mtd: nand: tango: Reset pbus to raw mode in probe
mtd: nand: tango: Update DT binding description
mtd: nand: oxnas_nand: fix build errors on arch/um, require HAS_IOMEM
mtd: nand: xway: fix build because of module functions
mtd: nand: xway: disable module support
Philippe Reynes [Sat, 14 Jan 2017 22:26:22 +0000 (23:26 +0100)]
net: marvell: sky2: use new api ethtool_{get|set}_link_ksettings
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Philippe Reynes [Mon, 16 Jan 2017 21:46:08 +0000 (22:46 +0100)]
net: marvell: skge: use new api ethtool_{get|set}_link_ksettings
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
The callback set_link_ksettings no longer update the value
of advertising, as the struct ethtool_link_ksettings is
defined as const.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Philippe Reynes [Sun, 15 Jan 2017 22:18:21 +0000 (23:18 +0100)]
net: jme: use new api ethtool_{get|set}_link_ksettings
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Philippe Reynes [Sat, 14 Jan 2017 11:33:19 +0000 (12:33 +0100)]
net: korina: use new api ethtool_{get|set}_link_ksettings
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 17 Jan 2017 01:07:29 +0000 (20:07 -0500)]
Merge branch 'mvneta-xmit_more-bql'
Marcin Wojtas says:
====================
mvneta xmit_more and bql support
This is a delayed v2 of short patchset, which introduces xmit_more and BQL
to mvneta driver. The only one change was added in xmit_more support -
condition check preventing excessive descriptors concatenation before
flushing in HW.
Any comments or feedback would be welcome.
Changelog:
v1 -> v2:
* Add checking condition that ensures too much descriptors are not
concatenated before flushing in HW.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Marcin Wojtas [Mon, 16 Jan 2017 17:08:32 +0000 (18:08 +0100)]
net: mvneta: add BQL support
Tests showed that when whole bandwidth is consumed, the latency for
various kind of traffic can reach high values. With saturated
link (e.g. with iperf from target to host) simple ping could take
significant amount of time. BQL proved to improve this situation
when implemented in mvneta driver. Measurements of ping latency
for 3 link speeds:
Speed | Latency w/o BQL | Latency with BQL
10 | 7-14 ms | 3.5 ms
100 | 2-12 ms | 0.6 ms
1000 | often timeout | up to 2ms
Decreasing latency as above result in sligt performance cost - 4kpps
(-1.4%) when pushing 64B packets via two bridged interfaces of Armada 38x.
For 1500B packets in the same setup, the mpstat tool showed +8% of
CPU occupation (default affinity, second CPU idle). Even though this
cost seems reasonable to take, considering other improvements.
This commit adds byte queue limit mechanism for the mvneta driver.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simon Guinot [Mon, 16 Jan 2017 17:08:31 +0000 (18:08 +0100)]
net: mvneta: add xmit_more support
Basing on xmit_more flag of the skb, TX descriptors can be concatenated
before flushing. This commit delay Tx descriptor flush if the queue is
running and if there is more skb's to send.
A maximum allowed number of descriptors for flushing at once due to
MVNETA_TXQ_UPDATE_REG(q) reqisters limitation, is 255. Because of that
a new macro was added (MVNETA_TXQ_DEC_SENT_MASK) in order to ensure that
concatenated amount of descriptor does not exceed that value.
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jamal Hadi Salim [Sun, 15 Jan 2017 15:14:06 +0000 (10:14 -0500)]
net sched actions: fix refcnt when GETing of action after bind
Demonstrating the issue:
.. add a drop action
$sudo $TC actions add action drop index 10
.. retrieve it
$ sudo $TC -s actions get action gact index 10
action order 1: gact action drop
random type none pass val 0
index 10 ref 2 bind 0 installed 29 sec used 29 sec
Action statistics:
Sent 0 bytes 0 pkt (dropped 0, overlimits 0 requeues 0)
backlog 0b 0p requeues 0
... bug 1 above: reference is two.
Reference is actually 1 but we forget to subtract 1.
... do a GET again and we see the same issue
try a few times and nothing changes
~$ sudo $TC -s actions get action gact index 10
action order 1: gact action drop
random type none pass val 0
index 10 ref 2 bind 0 installed 31 sec used 31 sec
Action statistics:
Sent 0 bytes 0 pkt (dropped 0, overlimits 0 requeues 0)
backlog 0b 0p requeues 0
... lets try to bind the action to a filter..
$ sudo $TC qdisc add dev lo ingress
$ sudo $TC filter add dev lo parent ffff: protocol ip prio 1 \
u32 match ip dst 127.0.0.1/32 flowid 1:1 action gact index 10
... and now a few GETs:
$ sudo $TC -s actions get action gact index 10
action order 1: gact action drop
random type none pass val 0
index 10 ref 3 bind 1 installed 204 sec used 204 sec
Action statistics:
Sent 0 bytes 0 pkt (dropped 0, overlimits 0 requeues 0)
backlog 0b 0p requeues 0
$ sudo $TC -s actions get action gact index 10
action order 1: gact action drop
random type none pass val 0
index 10 ref 4 bind 1 installed 206 sec used 206 sec
Action statistics:
Sent 0 bytes 0 pkt (dropped 0, overlimits 0 requeues 0)
backlog 0b 0p requeues 0
$ sudo $TC -s actions get action gact index 10
action order 1: gact action drop
random type none pass val 0
index 10 ref 5 bind 1 installed 235 sec used 235 sec
Action statistics:
Sent 0 bytes 0 pkt (dropped 0, overlimits 0 requeues 0)
backlog 0b 0p requeues 0
.... as can be observed the reference count keeps going up.
After the fix
$ sudo $TC actions add action drop index 10
$ sudo $TC -s actions get action gact index 10
action order 1: gact action drop
random type none pass val 0
index 10 ref 1 bind 0 installed 4 sec used 4 sec
Action statistics:
Sent 0 bytes 0 pkt (dropped 0, overlimits 0 requeues 0)
backlog 0b 0p requeues 0
$ sudo $TC -s actions get action gact index 10
action order 1: gact action drop
random type none pass val 0
index 10 ref 1 bind 0 installed 6 sec used 6 sec
Action statistics:
Sent 0 bytes 0 pkt (dropped 0, overlimits 0 requeues 0)
backlog 0b 0p requeues 0
$ sudo $TC qdisc add dev lo ingress
$ sudo $TC filter add dev lo parent ffff: protocol ip prio 1 \
u32 match ip dst 127.0.0.1/32 flowid 1:1 action gact index 10
$ sudo $TC -s actions get action gact index 10
action order 1: gact action drop
random type none pass val 0
index 10 ref 2 bind 1 installed 32 sec used 32 sec
Action statistics:
Sent 0 bytes 0 pkt (dropped 0, overlimits 0 requeues 0)
backlog 0b 0p requeues 0
$ sudo $TC -s actions get action gact index 10
action order 1: gact action drop
random type none pass val 0
index 10 ref 2 bind 1 installed 33 sec used 33 sec
Action statistics:
Sent 0 bytes 0 pkt (dropped 0, overlimits 0 requeues 0)
backlog 0b 0p requeues 0
Fixes:
aecc5cefc389 ("net sched actions: fix GETing actions")
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Mon, 16 Jan 2017 20:15:59 +0000 (12:15 -0800)]
Merge tag 'nfs-for-4.10-3' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull NFS client bugfixes from Trond Myklebust:
- fix invalid fget()/fput() calls when doing file locking
- fix multiple directory cache invalidation issues due to the client
failing to recognise that the directory wasn't changed
- fix client recovery when server reboots multiple times
* tag 'nfs-for-4.10-3' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
NFSv4: Fix client recovery when server reboots multiple times
NFSv4: update_changeattr should update the attribute timestamp
NFSv4: Don't call update_changeattr() unless the unlink is successful
NFSv4: Don't apply change_info4 twice on rename within a directory
NFSv4: Call update_changeattr() from _nfs4_proc_open only if a file was created
nfs: Don't take a reference on fl->fl_file for LOCK operation
David S. Miller [Mon, 16 Jan 2017 20:08:29 +0000 (15:08 -0500)]
Merge branch 'mlx4-core-fixes'
Tariq Toukan says:
====================
mlx4 core fixes
This patchset contains bug fixes from Jack to the mlx4 Core driver.
Patch 1 solves a race in the flow of CQ free.
Patch 2 moves some qp context flags update to the correct qp transition.
Patch 3 eliminates warnings from the path of SRQ_LIMIT that flood the message log,
and keeps them only in the path of SRQ_CATAS_ERROR.
Series generated against net commit:
1a717fcf8bbe Merge tag 'mac80211-for-davem-2017-01-13' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jack Morgenstein [Mon, 16 Jan 2017 16:31:39 +0000 (18:31 +0200)]
net/mlx4_core: Eliminate warning messages for SRQ_LIMIT under SRIOV
When running SRIOV, warnings for SRQ LIMIT events flood the Hypervisor's
message log when (correct, normally operating) apps use SRQ LIMIT events
as a trigger to post WQEs to SRQs.
Add more information to the existing debug printout for SRQ_LIMIT, and
output the warning messages only for the SRQ CATAS ERROR event.
Fixes:
acba2420f9d2 ("mlx4_core: Add wrapper functions and comm channel and slave event support to EQs")
Fixes:
e0debf9cb50d ("mlx4_core: Reduce warning message for SRQ_LIMIT event to debug level")
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jack Morgenstein [Mon, 16 Jan 2017 16:31:38 +0000 (18:31 +0200)]
net/mlx4_core: Fix when to save some qp context flags for dynamic VST to VGT transitions
Save the qp context flags byte containing the flag disabling vlan stripping
in the RESET to INIT qp transition, rather than in the INIT to RTR
transition. Per the firmware spec, the flags in this byte are active
in the RESET to INIT transition.
As a result of saving the flags in the incorrect qp transition, when
switching dynamically from VGT to VST and back to VGT, the vlan
remained stripped (as is required for VST) and did not return to
not-stripped (as is required for VGT).
Fixes:
f0f829bf42cd ("net/mlx4_core: Add immediate activate for VGT->VST->VGT")
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jack Morgenstein [Mon, 16 Jan 2017 16:31:37 +0000 (18:31 +0200)]
net/mlx4_core: Fix racy CQ (Completion Queue) free
In function mlx4_cq_completion() and mlx4_cq_event(), the
radix_tree_lookup requires a rcu_read_lock.
This is mandatory: if another core frees the CQ, it could
run the radix_tree_node_rcu_free() call_rcu() callback while
its being used by the radix tree lookup function.
Additionally, in function mlx4_cq_event(), since we are adding
the rcu lock around the radix-tree lookup, we no longer need to take
the spinlock. Also, the synchronize_irq() call for the async event
eliminates the need for incrementing the cq reference count in
mlx4_cq_event().
Other changes:
1. In function mlx4_cq_free(), replace spin_lock_irq with spin_lock:
we no longer take this spinlock in the interrupt context.
The spinlock here, therefore, simply protects against different
threads simultaneously invoking mlx4_cq_free() for different cq's.
2. In function mlx4_cq_free(), we move the radix tree delete to before
the synchronize_irq() calls. This guarantees that we will not
access this cq during any subsequent interrupts, and therefore can
safely free the CQ after the synchronize_irq calls. The rcu_read_lock
in the interrupt handlers only needs to protect against corrupting the
radix tree; the interrupt handlers may access the cq outside the
rcu_read_lock due to the synchronize_irq calls which protect against
premature freeing of the cq.
3. In function mlx4_cq_event(), we change the mlx_warn message to mlx4_dbg.
4. We leave the cq reference count mechanism in place, because it is
still needed for the cq completion tasklet mechanism.
Fixes:
6d90aa5cf17b ("net/mlx4_core: Make sure there are no pending async events when freeing CQ")
Fixes:
225c7b1feef1 ("IB/mlx4: Add a driver Mellanox ConnectX InfiniBand adapters")
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Paul Blakey [Mon, 16 Jan 2017 08:45:13 +0000 (10:45 +0200)]
net/sched: cls_flower: Disallow duplicate internal elements
Flower currently allows having the same filter twice with the same
priority. Actions (and statistics update) will always execute on the
first inserted rule leaving the second rule unused.
This patch disallows that.
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Heiner Kallweit [Sun, 15 Jan 2017 18:19:00 +0000 (19:19 +0100)]
net: stmmac: don't use netdev_[dbg, info, ..] before net_device is registered
Don't use netdev_info and friends before the net_device is registered.
This avoids ugly messages like
"meson8b-dwmac
c9410000.ethernet (unnamed net_device) (uninitialized):
Enable RX Mitigation via HW Watchdog Timer"
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Arnd Bergmann [Sun, 15 Jan 2017 17:50:46 +0000 (19:50 +0200)]
net/mlx5e: Fix a -Wmaybe-uninitialized warning
As found by Olof's build bot, we gain a harmless warning about a
potential uninitialized variable reference in mlx5:
drivers/net/ethernet/mellanox/mlx5/core/en_tc.c: In function 'parse_tc_fdb_actions':
drivers/net/ethernet/mellanox/mlx5/core/en_tc.c:769:13: warning: 'out_dev' may be used uninitialized in this function [-Wmaybe-uninitialized]
drivers/net/ethernet/mellanox/mlx5/core/en_tc.c:811:21: note: 'out_dev' was declared here
This was introduced through the addition of an 'IS_ERR/PTR_ERR' pair
that gcc is unfortunately unable to completely figure out.
The problem being gcc cannot tell that if(IS_ERR()) in
mlx5e_route_lookup_ipv4() is equivalent to checking if(err) later,
so it assumes that 'out_dev' is used after the 'return PTR_ERR(rt)'.
The PTR_ERR_OR_ZERO() case by comparison is fairly easy to detect
by gcc, so it can't get that wrong, so it no longer warns.
Hadar Hen Zion already attempted to fix the warning earlier by adding fake
initializations, but that ended up not fully addressing all warnings, so
I'm reverting it now that it is no longer needed.
Link: http://arm-soc.lixom.net/buildlogs/mainline/v4.10-rc3-98-gcff3b2c/
Fixes:
a42485eb0ee4 ("net/mlx5e: TC ipv4 tunnel encap offload error flow fixes")
Fixes:
a757d108dc1a ("net/mlx5e: Fix kbuild warnings for uninitialized parameters")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Lebrun [Sun, 15 Jan 2017 14:26:16 +0000 (15:26 +0100)]
ipv6: sr: add missing Kbuild export for header files
Add missing IPv6-SR header files in include/uapi/linux/Kbuild.
Also, prevent seg6_lwt_headroom() from being exported and add
missing linux/types.h include.
Signed-off-by: David Lebrun <david.lebrun@uclouvain.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Sun, 15 Jan 2017 00:34:25 +0000 (01:34 +0100)]
bpf, trace: make ctx access checks more robust
Make sure that ctx cannot potentially be accessed oob by asserting
explicitly that ctx access size into pt_regs for BPF_PROG_TYPE_KPROBE
programs must be within limits. In case some 32bit archs have pt_regs
not being a multiple of 8, then BPF_DW access could cause such access.
BPF_PROG_TYPE_KPROBE progs don't have a ctx conversion function since
there's no extra mapping needed. kprobe_prog_is_valid_access() didn't
enforce sizeof(long) as the only allowed access size, since LLVM can
generate non BPF_W/BPF_DW access to regs from time to time.
For BPF_PROG_TYPE_TRACEPOINT we don't have a ctx conversion either, so
add a BUILD_BUG_ON() check to make sure that BPF_DW access will not be
a similar issue in future (ctx works on event buffer as opposed to
pt_regs there).
Fixes:
2541517c32be ("tracing, perf: Implement BPF programs attached to kprobes")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Basil Gunn [Sat, 14 Jan 2017 20:18:55 +0000 (12:18 -0800)]
ax25: Fix segfault after sock connection timeout
The ax.25 socket connection timed out & the sock struct has been
previously taken down ie. sock struct is now a NULL pointer. Checking
the sock_flag causes the segfault. Check if the socket struct pointer
is NULL before checking sock_flag. This segfault is seen in
timed out netrom connections.
Please submit to -stable.
Signed-off-by: Basil Gunn <basil@pacabunga.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mahesh Bandewar [Fri, 13 Jan 2017 23:48:30 +0000 (15:48 -0800)]
ipvlan: fix dev_id creation corner case.
In the last patch
da36e13cf65 ("ipvlan: improvise dev_id generation
logic in IPvlan") I missed some part of Dave's suggestion and because
of that the dev_id creation could fail in a corner case scenario. This
would happen when more or less 64k devices have been already created and
several have been deleted. If the devices that are still sticking around
are the last n bits from the bitmap. So in this scenario even if lower
bits are available, the dev_id search is so narrow that it always fails.
Fixes:
da36e13cf65 ("ipvlan: improvise dev_id generation logic in IPvlan")
CC: David Miller <davem@davemloft.org>
CC: Eric Dumazet <edumazet@google.com>
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Fri, 13 Jan 2017 22:38:15 +0000 (23:38 +0100)]
bpf: rework prog_digest into prog_tag
Commit
7bd509e311f4 ("bpf: add prog_digest and expose it via
fdinfo/netlink") was recently discussed, partially due to
admittedly suboptimal name of "prog_digest" in combination
with sha1 hash usage, thus inevitably and rightfully concerns
about its security in terms of collision resistance were
raised with regards to use-cases.
The intended use cases are for debugging resp. introspection
only for providing a stable "tag" over the instruction sequence
that both kernel and user space can calculate independently.
It's not usable at all for making a security relevant decision.
So collisions where two different instruction sequences generate
the same tag can happen, but ideally at a rather low rate. The
"tag" will be dumped in hex and is short enough to introspect
in tracepoints or kallsyms output along with other data such
as stack trace, etc. Thus, this patch performs a rename into
prog_tag and truncates the tag to a short output (64 bits) to
make it obvious it's not collision-free.
Should in future a hash or facility be needed with a security
relevant focus, then we can think about requirements, constraints,
etc that would fit to that situation. For now, rework the exposed
parts for the current use cases as long as nothing has been
released yet. Tested on x86_64 and s390x.
Fixes:
7bd509e311f4 ("bpf: add prog_digest and expose it via fdinfo/netlink")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Cc: Andy Lutomirski <luto@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Edward Cree [Fri, 13 Jan 2017 21:20:29 +0000 (21:20 +0000)]
sfc: get PIO buffer size from the NIC
The 8000 series SFC NICs have 4K PIO buffers, rather than the 2K of
the 7000 series. Rather than having a hard-coded PIO buffer size
(ER_DZ_TX_PIOBUF_SIZE), read it from the GET_CAPABILITIES_V2 MCDI
response.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Edward Cree [Fri, 13 Jan 2017 21:20:14 +0000 (21:20 +0000)]
sfc: allow PIO more often
If an option descriptor has been sent on a queue but not followed by a
packet, there will have been no completion event, so the read and write
counts won't match and we'll think we can't do PIO. This combines with
the fact that we have two TX queues (for en/disable checksum offload),
and that both must be empty for PIO to happen.
This patch adds a separate "packet_write_count" that tracks the most
recent write_count we expect to see a completion event for; this excludes
option descriptors but _includes_ PIO descriptors (even though they look
like option descriptors). This is then used, rather than write_count,
in efx_nic_tx_is_empty().
We only bother to maintain packet_write_count on EF10, since on Siena
(a) there are no option descriptors and it always equals write_count, and
(b) there's no PIO, so we don't need it anyway.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marcelo Ricardo Leitner [Fri, 13 Jan 2017 20:31:15 +0000 (18:31 -0200)]
sctp: remove useless code from sctp_apply_peer_addr_params
sctp_frag_point() doesn't store anything, and thus just calling it
cannot do anything useful.
sctp_apply_peer_addr_params is only called by
sctp_setsockopt_peer_addr_params. When operating on an asoc,
sctp_setsockopt_peer_addr_params will call sctp_apply_peer_addr_params
once for the asoc, and then once for each transport this asoc has,
meaning that the frag_point will be recomputed when updating the
transports and calling it when updating the asoc is not necessary.
IOW, no action is needed here and we can remove this call.
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Reviewed-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marcelo Ricardo Leitner [Fri, 13 Jan 2017 20:27:33 +0000 (18:27 -0200)]
sctp: remove unused var from sctp_process_asconf
Assigned but not used.
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Reviewed-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Colin Ian King [Fri, 13 Jan 2017 18:48:20 +0000 (18:48 +0000)]
flow dissector: check if arp_eth is null rather than arp
arp is being checked instead of arp_eth to see if the call to
__skb_header_pointer failed. Fix this by checking arp_eth is
null instead of arp. Also fix to use length hlen rather than
hlen - sizeof(_arp); thanks to Eric Dumazet for spotting
this latter issue.
CoverityScan CID#1396428 ("Logically dead code") on 2nd
arp comparison (which should be arp_eth instead).
Fixes: commit
55733350e5e8b70c5 ("flow disector: ARP support")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>