ndisc: Reduce number of arguments for ndisc_fill_addr_option().

Add pointer to struct net_device (dev) and remove
data_len (= dev->addr_len) and addr_type (= dev->type).

Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: ethernet: davinci: Fix build breakage

The correct name of the transmit DMA channel field in struct emac_priv
is txchan, not txch.

Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

firewire net: Use LL_RESERVED_SPACE(), HH_DATA_OFF().

Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

firewire net: Ensure checksumming in upper layer.

It is wrong to set skb->ip_summed to CHECKSUM_UNNECESSARY unless
the device has already checked it.

Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

usbnet: pegasus: set wakeup enable in set_wol

This patch calls device_set_wakeup_enable() inside set_wol
callback, so that turning on WOL from user mode utility
can make the 'wakeup' of pegasus device to be enabled, then
remote wakeup may be enabled before putting into sleep.

Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Petko Manolov <petkan@users.sourceforge.net>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net/mlx4_en: remove redundant code

remove redundant code from build_inline_wqe()

Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-By: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ndisc: Make several arguments for ndisc_send_na() boolean.

Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

ipv6: Optimize ipv6_addr_is_ll_all_{nodes,routers}().

Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

ipv6: Optimize ipv6_addr_is_solict_mult().

Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

ipv6: Introduce ipv6_addr_is_solict_mult() to check Solicited Node Multicast Addresses.

Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

ipv6: Make ipv6_addr_is_XXX() return boolean.

ipv6_addr_is_{multicast,ll_all_nodes,ll_all_routers,isatap}()
return boolean.

Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: asix: ax88772_unbind() can be static

Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'master' of git://git./linux/kernel/git/jkirsher/net-next

Jeff Kirsher says:

====================
This series contains updates to ixgbe, ixgbevf and igb.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'batman-adv-for-davem' of git://git.open-mesh.org/linux-merge

Included changes:
- sysfs removal postponement during interface un-registration
- random32() function renaming
- struct refactoring
- kernel doc improvement
- deleyed_work initialisation clean up work
- copyright year and internal version number update
- kernel doc improvement

Signed-off-by: David S. Miller <davem@davemloft.net>

batman-adv: Start new development cycle

Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>

batman-adv: update copyright years

Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>

batman-adv: postpone sysfs removal when unregistering

When processing the unregister notify for a hard interface, removing
the sysfs files may lead to a circular deadlock (rtnl mutex <->
s_active).

To overcome this problem, postpone the sysfs removal in a worker.

Reported-by: Sasha Levin <sasha.levin@oracle.com>
Reported-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>

batman-adv: rename random32() to prandom_u32()

Use more preferable function name which implies using a pseudo-random
number generator.

Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Cc: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Cc: Antonio Quartulli <ordex@autistici.org>
Cc: b.a.t.m.a.n@lists.open-mesh.org
Cc: "David S. Miller" <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Signed-off-by: Antonio Quartulli <ordex@autistici.org>

batman-adv: kernel doc for types.h

Thanks to Sven Eckelmann and Simon Wunderlich for their support.

Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>

batman-adv: rename batadv_claim struct to make clear it is used by bla

Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>

batman-adv: rename batadv_backbone_gw struct to make clear it is used by bla

Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>

batman-adv: rename batadv_recvlist_node struct to make clear it is used by vis

Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>

batman-adv: rename batadv_if_list_entry struct to make clear it is used by vis

Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>

batman-adv: group tt type definitions together

Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>

batman-adv: mark debug_log struct as bat_priv only struct

Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>

batman-adv: align kernel doc properly

Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>

batman-adv: a delayed_work has to be initialised once

A delayed_work struct does not need to be initialized each
every time before being enqueued. Therefore the
INIT_DELAYED_WORK() macro should be used during the
initialization process only.

Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>

igb: Copyright string update to year 2013

This patch updates Copyright year to 2013

v2: Changed Copyright year on Makefile

Signed-off-by: Akeem G. Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

igb: Replace rmb in Tx cleanup with read_barrier_depends

The rmb in the Tx cleanup path is a much stronger barrier than we really need.
All that is really needed is a read_barrier_depends since the location of the
EOP descriptor is dependent on the eop_desc value.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

ixgbevf: Fix statistics corruption

When the physical function (PF) is reset for any reason the statistics
collection in ixgbevf_update_stats needs to wait to update until after
the reset synchronization ensures that the PF driver is up and running
and is finished with its own reset.  Go ahead and clear the link flag to
indicate this when the control message from the PF is received.  The
reset synchronization and recovery in the watchdog task will eventually
set the link flag up when the PF has resumed.

Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

ixgbevf: Fix link up messages

Use dev_info to log link up/down messages.

Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

ixgbevf: Synch out of tree and in tree mailbox interrupt handlers

The out of tree driver and the in kernel driver should use the same
interrupt handling logic for mailbox interrupts.  The difference in
the handlers was causing dissimilar behavior between the two drivers
complicating debug and trouble shooting.

Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

ixgbe: Improve performance and reduce size of ixgbe_tx_map

This change is meant to both improve the performance and reduce the size of
ixgbe_tx_map.  To do this I have expanded the work done in the main loop by
pushing first into tx_buffer.  This allows us to pull in the dma_mapping_error
check, the tx_buffer value assignment, and the initial DMA value assignment to
the Tx descriptor.  The net result is that the function reduces in size by a
little over a 100 bytes and is about 1% or 2% faster.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

ixgbe: Update ixgbe Tx flags to improve code efficiency

This change is meant to improve the efficiency of the Tx flags in ixgbe by
aligning them with the values that will later be written into either the
cmd_type or olinfo.  By doing this we are able to reduce most of these
functions to either just a simple shift followed by an or in the case of
cmd_type, or an and followed by an or in the case of olinfo.

To do this I also needed to change the logic and/or drop some flags.  I
dropped the IXGBE_TX_FLAGS_FSO and it was replaced by IXGBE_TX_FLAGS_TSO since
the only place it was ever checked was in conjunction with IXGBE_TX_FLAGS_TSO.
I replaced IXGBE_TX_FLAGS_TXSW with IXGBE_TX_FLAGS_CC, this way we have a
clear point for what the flag is meant to do.  Finally the
IXGBE_TX_FLAGS_NO_IFCS was dropped since were are already carrying the data
for that flag in the skb.  Instead we can just check the bitflag in the skb.

In order to avoid type conversion errors I also adjusted the locations
where we were switching between CPU and little endian.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

ixgbe: Always use context 0, even for FCoE and TSO

We were spending cycles separating the FCoE and TSO contexts even though we
always overwriting the context anyway.  Instead of doing that we can just
use context 0 for all descriptors.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

ixgbe: Make TSO check for CHECKSUM_PARTIAL to avoid skb_is_gso check

This change is meant to reduce the overhead for workloads that are not
using either TSO or checksum offloads.  Most of the time the compiler
should jump ahead after failing this check to the VLAN check since in the
ixgbe_tx_csum call we start with that check as well.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

ixgbe: SR-IOV: dynamic IEEE DCBx default priority changes

IEEE DCBx has a mechanism to change the default user priority. In
the normal case the OS can handle this via cgroups, iptables, socket,
options etc.

With SR-IOV and direct assigned VF devices the default priority
needs to be set by the PF device so the inserted VLAN tag is
correct.

Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Marcus Dennis <marcusx.e.dennis@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

ipv6: remove unneeded check to pskb_may_pull in ipip6_rcv

This is already checked by the caller (tunnel64_rcv) and brings ipip6_rcv
in line with ipip_rcv.

Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

ndisc: Check NS message length before access.

Check message length before accessing "target" field,
as we do for other types.

Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

ipv6: Remove unused neigh argument for icmp6_dst_alloc() and its callers.

Because of rt->n removal, we do not need neigh argument any more.

Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

enic: change sprintf() to snprintf()

These are copying data into 16 char arrays.  They all specify that the
first string can't be more than 11 characters but once you add on the
"-rx-" and the NUL character there isn't space for the %d.

The first string is probably never going to be 11 characters, but if it
is then let's truncate the string instead of corrupting memory.

Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

smsc: smc911x: Fix sparse warnings

ioremap returns 'void __iomem *' type.

Fix the following build warnings:

drivers/net/ethernet/smsc/smc911x.c:2079:14: warning: incorrect type in assignment (different address spaces)
drivers/net/ethernet/smsc/smc911x.c:2079:14:    expected unsigned int *addr
drivers/net/ethernet/smsc/smc911x.c:2079:14:    got void [noderef] <asn:2>*
drivers/net/ethernet/smsc/smc911x.c:2086:18: warning: incorrect type in assignment (different address spaces)
drivers/net/ethernet/smsc/smc911x.c:2086:18:    expected void [noderef] <asn:2>*base
drivers/net/ethernet/smsc/smc911x.c:2086:18:    got unsigned int *addr
drivers/net/ethernet/smsc/smc911x.c:2091:25: warning: incorrect type in argument 1 (different address spaces)
drivers/net/ethernet/smsc/smc911x.c:2091:25:    expected void volatile [noderef] <asn:2>*addr
drivers/net/ethernet/smsc/smc911x.c:2091:25:    got unsigned int *addr

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: usb: initialize tmp in dm9601.c to avoid warning

In two places, tmp is initialized implicitly by being passed as a
pointer during a function call.  However, this is not obvious to the
compiler, which logs a warning.

Signed-off-by: Simon Que <sque@chromium.org>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: ethernet: davinci_cpdma: Add boundary for rx and tx descriptors

When there is heavy transmission traffic in the CPDMA, then Rx descriptors
memory is also utilized as tx desc memory looses all rx descriptors and the
driver stops working then.

This patch adds boundary for tx and rx descriptors in bd ram dividing the
descriptor memory to ensure that during heavy transmission tx doesn't use
rx descriptors.

This patch is already applied to davinci_emac driver, since CPSW and
davici_dmac shares the same CPDMA, moving the boundry seperation from
Davinci EMAC driver to CPDMA driver which was done in the following
commit

commit 86d8c07ff2448eb4e860e50f34ef6ee78e45c40c
Author: Sascha Hauer <s.hauer@pengutronix.de>
Date:   Tue Jan 3 05:27:47 2012 +0000

    net/davinci: do not use all descriptors for tx packets

    The driver uses a shared pool for both rx and tx descriptors.
    During open it queues fixed number of 128 descriptors for receive
    packets. For each received packet it tries to queue another
    descriptor. If this fails the descriptor is lost for rx.
    The driver has no limitation on tx descriptors to use, so it
    can happen during a nmap / ping -f attack that the driver
    allocates all descriptors for tx and looses all rx descriptors.
    The driver stops working then.
    To fix this limit the number of tx descriptors used to half of
    the descriptors available, the rx path uses the other half.

    Tested on a custom board using nmap / ping -f to the board from
    two different hosts.

Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

6lowpan: Handle uncompressed IPv6 packets over 6LoWPAN

Handle the reception of uncompressed packets (dispatch type = IPv6).

Signed-off-by: Alan Ott <alan@signal11.us>
Signed-off-by: David S. Miller <davem@davemloft.net>

6lowpan: Refactor packet delivery into a function

Refactor the handing of the skb's to the individual lowpan devices into a
function.

Signed-off-by: Alan Ott <alan@signal11.us>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: fec: enable pause frame to improve rx prefomance for 1G network

The limition of imx6 internal bus cause fec can't achieve 1G perfomance.
There will be many packages lost because FIFO over run.

This patch enable pause frame flow control.

Before this patch
iperf -s -i 1
TCP window size: 85.3 KByte (default)
------------------------------------------------------------
[  4] local 10.192.242.153 port 5001 connected with 10.192.242.94 port 49773
[ ID] Interval       Transfer     Bandwidth
[  4]  0.0- 1.0 sec  6.35 MBytes  53.3 Mbits/sec
[  4]  1.0- 2.0 sec  3.39 MBytes  28.5 Mbits/sec
[  4]  2.0- 3.0 sec  2.63 MBytes  22.1 Mbits/sec
[  4]  3.0- 4.0 sec  1.10 MBytes  9.23 Mbits/sec

ifconfig
   RX packets:46195 errors:1859 dropped:1 overruns:1859 frame:1859

After this patch
iperf -s -i 1

[  4] local 10.192.242.153 port 5001 connected with 10.192.242.94 port 49757
[ ID] Interval       Transfer     Bandwidth
[  4]  0.0- 1.0 sec  49.8 MBytes   418 Mbits/sec
[  4]  1.0- 2.0 sec  50.1 MBytes   420 Mbits/sec
[  4]  2.0- 3.0 sec  47.5 MBytes   399 Mbits/sec
[  4]  3.0- 4.0 sec  45.9 MBytes   385 Mbits/sec
[  4]  4.0- 5.0 sec  44.8 MBytes   376 Mbits/sec

ifconfig
   RX packets:2348454 errors:0 dropped:16 overruns:0 frame:0

Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: asix: handle packets crossing URB boundaries

ASIX AX88772B started to pack data even more tightly. Packets and the ASIX packet
header may now cross URB boundaries. To handle this we have to introduce
some state between individual calls to asix_rx_fixup().

Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: asix: init ASIX AX88772B MAC from EEPROM

The device comes up with a MAC address of all zeros. We need to read the
initial device MAC from EEPROM so it can be set properly later.

Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'intel'

Jeff Kirsher says:

====================
This series contains updates to e1000e and igb.  Most notably is the
added timestamp support in e1000e and additional software timestamp
support in igb.  As well as, the added thermal data support and SR-IOV
configuration support in igb.

v2- dropped the following patches from the previous 14 patch series
because changes were requested from the community:
  e1000e: add support for IEEE-1588 PTP
  igb: Report L4 Rx hash via skb->l4_rxhash
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

igb: Use in-kernel PTP_EV_PORT #define

Rather than use an extra #define for something that already exists, use the
kernel #define for the PTP port.

Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Acked-by: Jacob Keller <Jacob.e.keller@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

igb: Free any held skb that should have been timestamped on remove

To prevent a race condition where an skb has been saved to return the Tx
timestamp later and the driver is removed, add a check to determine if we
have an skb stored and, if so, free it.

Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Acked-by: Jacob Keller <Jacob.e.keller@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

igb: Add mechanism for detecting latched hardware Rx timestamp

Add a check against possible Rx timestamp freezing in the hardware via
watchdog mechanism. This situation can occur when an Rx timestamp has been
latched, but the packet has been dropped because the Rx ring is full.

Whenever a packet comes in that should be timestamped, the Rx timestamp
gets latched into the hardware registers and we will store the jiffy value
in the rx_ring. The watchdog will keep track of his own jiffy timer
whenever there is no valid timestamp in the registers.

If the watchdog detects a valid timestamp in the registers, meaning that no
Rx packet has consumed it yet, it will check which time is most recent: the
last time in the watchdog or any time in the rx_rings. If the most recent
"event" was more than 5 seconds ago, it will flush the Rx timestamp and
print a warning message to the syslog.

Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Acked-by: Jacob Keller <Jacob.e.keller@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

igb: Add timeout for PTP Tx work item

When transmitting a packet that must return a Tx timestamp, a work item
gets scheduled to poll for the Tx timestamp being completed in hardware.
Add a timeout on this work item of 15 seconds from when the driver gets the
skb, after which it will stop polling. Report via stats and system log if
this occurs.

Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Acked-by: Jacob Keller <Jacob.e.keller@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

igb: Add support for SW timestamping

Enable SW timestamping for situations where the user may prefer it over HW
timestamping or there may not be HW timestamping.

Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Acked-by: Jacob Keller <Jacob.e.keller@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

igb: Enable hwmon data output for thermal sensors via I2C.

Some of our adapters have internal sensors that report thermal data.  This
patch enables reporting of that data via sysfs.

Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

igb: Add support functions to access thermal data.

Some of our devices have internal sensors for reporting thermal data.
This patch creates the interface to the sensors for exporting via sysfs.
Subsequent patch will actually export the data.

Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

igb: Add i2c interface to igb.

Some of our adapters have sensors on them accessible via i2c and a private
interface.  This patch implements the kernel interface for i2c to those sensors.
Subsequent patches will provide functions to export that data.

Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

igb: Enable SR-IOV configuration via PCI sysfs interface

Implement callback in the driver for the new PCI bus driver
interface that allows the user to enable/disable SR-IOV
virtual functions in a device via the sysfs interface.

Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e: add support for hardware timestamping on some devices

On 82574, 82583, 82579, I217 and I218 add support for hardware time
stamping of all or no Rx packets and Tx packets which have the
SKBTX_HW_TSTAMP flag set.  Update the .get_ts_info ethtool operation to
report the supported time stamping modes, and enable and disable hardware
time stamping with the SIOCSHWTSTAMP ioctl.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e: Use standard #defines for PCIe Capability ASPM fields

Use the standard #defines for PCIe Capability ASPM fields.

Previously we used PCIE_LINK_STATE_L0S and PCIE_LINK_STATE_L1 directly, but
these are defined for the Linux ASPM interfaces, e.g.,
pci_disable_link_state(), and only coincidentally match the actual register
bits.  PCIE_LINK_STATE_CLKPM, also part of that interface, does not match
the register bit.

Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: e1000-devel@lists.sourceforge.net
Acked-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e: add ethtool .get_eee/.set_eee

Add the ability to query and set Energy Efficient Ethernet parameters via
ethtool for applicable devices.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

ipv6: Complete neighbour entry removal from dst_entry.

CC: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

ipv6: Do not depend on rt->n in ip6_finish_output2().

If neigh is not found, create new one.

Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

ipv6: Do not depend on rt->n in ip6_dst_lookup_tail().

Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

ipv6: Introduce rt6_nexthop() to select nexthop address.

For RTF_GATEWAY route, return rt->rt6i_gateway.
Otherwise, return 2nd argument (destination address).

This will be used by following patches which remove rt->n
dependency patches in ip6_dst_lookup_tail() and ip6_finish_output2().

Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

ipv6: Do not depend on rt->n in rt6_probe().

Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

ipv6: Do not depend on rt->n in rt6_check_neigh().

CC: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

ipv6: Do not depend on rt->n in ip6_pol_route().

Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

ndisc: Introduce __ipv6_neigh_lookup_noref().

This function, which looks up neighbour entry for an IPv6 address
without touching refcnt, will be used for patches to remove
dependency on rt->n (neighbour entry in rt6_info).

Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

ipv6 route: Dump gateway based on RTF_GATEWAY flag and rt->rt6i_gateway.

Do not depend on rt->n.

Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

ndisc: Remove tbl argument for __ipv6_neigh_lookup().

We can refer to nd_tbl directly.

Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

ndisc: Update neigh->updated with write lock.

neigh->nud_state and neigh->updated are under protection of
neigh->lock.

Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnx2x: fix GRO parameters

bnx2x does an internal GRO pass but doesn't provide gso_segs, thus
breaking qdisc_pkt_len_init() in case ingress qdisc is used.

We store gso_segs in NAPI_GRO_CB(skb)->count, where tcp_gro_complete()
expects to find the number of aggregated segments.

Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

cxgb3: Fix Tx csum stats

Signed-off-by: Jay Hernandez <jay@chelsio.com>
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ipv6: fix ipv6_prefix_equal64_half mask conversion

Fix the 64bit optimized version of ipv6_prefix_equal to convert the
bitmask to network byte order only after the bit-shift.

The bug was introduced in:

3867517 ipv6: 64bit version of ipv6_prefix_equal().

Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: increase fragment memory usage limits

Increase the amount of memory usage limits for incomplete
IP fragments.

Arguing for new thresh high/low values:

 High threshold = 4 MBytes
 Low  threshold = 3 MBytes

The fragmentation memory accounting code, tries to account for the
real memory usage, by measuring both the size of frag queue struct
(inet_frag_queue (ipv4:ipq/ipv6:frag_queue)) and the SKB's truesize.

We want to be able to handle/hold-on-to enough fragments, to ensure
good performance, without causing incomplete fragments to hurt
scalability, by causing the number of inet_frag_queue to grow too much
(resulting longer searches for frag queues).

For IPv4, how much memory does the largest frag consume.

Maximum size fragment is 64K, which is approx 44 fragments with
MTU(1500) sized packets. Sizeof(struct ipq) is 200.  A 1500 byte
packet results in a truesize of 2944 (not 2048 as I first assumed)

  (44*2944)+200 = 129736 bytes

The current default high thresh of 262144 bytes, is obviously
problematic, as only two 64K fragments can fit in the queue at the
same time.

How many 64K fragment can we fit into 4 MBytes:

  4*2^20/((44*2944)+200) = 32.34 fragment in queues

An attacker could send a separate/distinct fake fragment packets per
queue, causing us to allocate one inet_frag_queue per packet, and thus
attacking the hash table and its lists.

How many frag queue do we need to store, and given a current hash size
of 64, what is the average list length.

Using one MTU sized fragment per inet_frag_queue, each consuming
(2944+200) 3144 bytes.

  4*2^20/(2944+200) = 1334 frag queues -> 21 avg list length

An attack could send small fragments, the smallest packet I could send
resulted in a truesize of 896 bytes (I'm a little surprised by this).

  4*2^20/(896+200)  = 3827 frag queues -> 59 avg list length

When increasing these number, we also need to followup with
improvements, that is going to help scalability.  Simply increasing
the hash size, is not enough as the current implementation does not
have a per hash bucket locking.

Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sk-filter: Add ability to lock a socket filter program

While a privileged program can open a raw socket, attach some
restrictive filter and drop its privileges (or send the socket to an
unprivileged program through some Unix socket), the filter can still
be removed or modified by the unprivileged program. This commit adds a
socket option to lock the filter (SO_LOCK_FILTER) preventing any
modification of a socket filter program.

This is similar to OpenBSD BIOCLOCK ioctl on bpf sockets, except even
root is not allowed change/drop the filter.

The state of the lock can be read with getsockopt(). No error is
triggered if the state is not changed. -EPERM is returned when a user
tries to remove the lock or to change/remove the filter while the lock
is active. The check is done directly in sk_attach_filter() and
sk_detach_filter() and does not affect only setsockopt() syscall.

Signed-off-by: Vincent Bernat <bernat@luffy.cx>
Signed-off-by: David S. Miller <davem@davemloft.net>

netpoll: fix a missing dev refcounting

__dev_get_by_name() doesn't refcount the network device,
so we have to do this by ourselves. Noticed by Eric.

Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ipv6: Fix endianess warning in ip6_flow_hdr().

Commit 3e4e4c1f ("ipv6: Introduce ip6_flow_hdr() to fill version,
tclass and flowlabel.) uses ntohl(), which should be htonl().

Found by Fengguang Wu <fengguang.wu@intel.com>.

Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

r8169: remove unneeded dirty_rx index

After commit 6f0333b ("r8169: use 50% less ram for RX ring") the rx
ring buffers are always copied making dirty_rx useless.

Signed-off-by: Timo Teräs <timo.teras@iki.fi>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

netpoll: fix a rtnl lock assertion failure

v4: hold rtnl lock for the whole netpoll_setup()
v3: remove the comment
v2: use RCU read lock

This patch fixes the following warning:

[   72.013864] RTNL: assertion failed at net/core/dev.c (4955)
[   72.017758] Pid: 668, comm: netpoll-prep-v6 Not tainted 3.8.0-rc1+ #474
[   72.019582] Call Trace:
[   72.020295]  [<ffffffff8176653d>] netdev_master_upper_dev_get+0x35/0x58
[   72.022545]  [<ffffffff81784edd>] netpoll_setup+0x61/0x340
[   72.024846]  [<ffffffff815d837e>] store_enabled+0x82/0xc3
[   72.027466]  [<ffffffff815d7e51>] netconsole_target_attr_store+0x35/0x37
[   72.029348]  [<ffffffff811c3479>] configfs_write_file+0xe2/0x10c
[   72.030959]  [<ffffffff8115d239>] vfs_write+0xaf/0xf6
[   72.032359]  [<ffffffff81978a05>] ? sysret_check+0x22/0x5d
[   72.033824]  [<ffffffff8115d453>] sys_write+0x5c/0x84
[   72.035328]  [<ffffffff819789d9>] system_call_fastpath+0x16/0x1b

In case of other races, hold rtnl lock for the entire netpoll_setup() function.

Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

vmxnet3: better RSS support

The VMXNET3 device provides RSS hash value for received packets,
but it is not being used.

Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

vmxnet3: use static RSS key

Rather than generating a different RSS key on each boot, just use
a predetermined value that will map same flow to same value on
every device for more predictable testing. This is already done
on most hardware drivers.

Initial key value just some arbitrary bits extracted once
from /dev/random.

Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

vmxnet3: remove unused irq_share_mode

This static variable is never set, it initializes to 0 which
is VMXNET3_INTR_BUDDYSHARE, and never changes.

Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

vmxnet3: remove device counter

An atomic counter of devices present is maintained but never used.

Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

vmxnet3: remove VMXNET3_MAX_DEVICES

Defined but never used.

Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

vmxnet3: use netdev_ printk wrappers

Use the standard netdev_xxx() and dev_xxx() wrappers to format
log messages.

Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

vmxnet3: use netdev_dbg

Use netdev_dbg() rather than dev_dbg() because the former prints
the device name which is more useful than the pci name.

Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

vmxnet3: fix messages printed before registration

This messages that occur during boot time from this device
when netdev_err is called before calling register_netdevice().
Switch to using dev_XXX macros which correlate message with PCI info which
is available.

Rather than fixing the features message, just remove it since
the information is redundant and available through ethtool.

Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

vmxnet3: remove unnecessary bookkeeping

The uncommitted[] array was set but never used except in a debug
message. Remove it.

Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

vmxnet3: use netdev_alloc_skb_ip_align

Use netdev_alloc_skb_align, rather than open code using dev_alloc_skb.
Change allocation at startup to use GFP_KERNEL.

Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'master' of git://git./linux/kernel/git/jkirsher/net-next

Jeff Kirsher says:

====================
This series contains updates to e1000e only.

v2- updates patch 09/15 "e1000e: resolve checkpatch PREFER_PR_LEVEL warning"
    based on feedback from Joe Perches.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

e1000e: merge multiple conditional statements into one

Cleanup a set of conditional tests.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e: cleanup code duplication

The removed code block is duplicated in e1000e_write_itr() so use that
instead.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e: cleanup magic number

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e: cleanup unnecessary line wrap

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e: cleanup unusual comment placement

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e: cleanup redundant statistics counter

rx_long_byte_count can be removed since it is duplicated in rx_bytes

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e: resolve checkpatch PREFER_PR_LEVEL warning

WARNING: Prefer netdev_info(netdev, ... then dev_info(dev, ...
then pr_info(...  to printk(KERN_INFO ...

v2 - remove unnecessary "e1000e:" prefix as pointed out by Joe Perches
     since that produces a redundant "e1000e:" in the log message

Cc: Joe Perches <joe@perches.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>