Arnd Bergmann [Tue, 8 Dec 2020 22:53:13 +0000 (23:53 +0100)]
Merge tag 'keystone_dts_for_5.11' of git://git./linux/kernel/git/ssantosh/linux-keystone into arm/dt
ARM: dts: Keystone DTS update for v5.11
- HDMI Support
- Analog Audio data support
* tag 'keystone_dts_for_5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone:
ARM: dts: keystone-k2g-evm: add HDMI and analog audio data
Link: https://lore.kernel.org/r/1606851472-26593-1-git-send-email-santosh.shilimkar@oracle.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Tue, 8 Dec 2020 22:51:51 +0000 (23:51 +0100)]
Merge tag 'qcom-dts-for-5.11' of git://git./linux/kernel/git/qcom/linux into arm/dt
Qualcomm DT updates for 5.11
This adds support for SD card, WiFi, LED, touchscreeni, touchkey and
fuel gauge to the Samsung Galaxy S5. Nexus 5 also gains fuel gauge
support.
Finally IPQ6016 gains support for the QPIC NAND controller.
* tag 'qcom-dts-for-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux:
arm64: dts: ipq6018: Add the QPIC peripheral nodes
ARM: dts: qcom-pma8084: Drop incorrect use of io-channel-ranges
ARM: dts: qcom: msm8974-lge-nexus5: Add fuel gauge
ARM: dts: qcom: msm8974-klte: Add fuel gauge
ARM: dts: qcom: msm8974-klte: Add support for SD card
ARM: dts: qcom: msm8974-klte: Add support for wifi
ARM: dts: qcom: msm8974-klte: Add gpio expander chip
ARM: dts: qcom: msm8974-klte: Add support for led
ARM: dts: qcom: msm8974-klte: Add support for touchscreen
ARM: dts: qcom: msm8974-klte: Add support for touchkey
ARM: dts: qcom: msm8974-klte: Merge pinctrl nodes
Link: https://lore.kernel.org/r/20201130190148.345302-1-bjorn.andersson@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Tue, 8 Dec 2020 22:50:07 +0000 (23:50 +0100)]
Merge tag 'qcom-arm64-for-5.11' of git://git./linux/kernel/git/qcom/linux into arm/dt
Qualcomm ARM64 DT updates for 5.11
For SM8250 the recently introduced support for handling boot-loader
stream mappings in the ARM SMMU allow us to enable this, and thereby USB
controller and PHY, SDHCI controller and FastRPC, as well as support for
the SM8250 HDK board has been added. Additionally PRNG and RTC is
enabled.
Similarly for SM8150, the ARM SMMU could be added which allows the
secondary USB controller and PHYs, as well as WiFi to be added and
support for the SM8150 HDK board to be introduced. Additionally
Coresight and support for the last-level cache controller was added.
MSM8916 finally has VDDCX and VDDMX removed as regulators and are now
handled by the rpmpd driver for the devices controlling them. The
Longsheer L8150 gains touchscreen, sensors, vibrator and LED support.
MSM8992 gains USB and SDHCI support as well as an I2C controller and the
associated RMI4 based touchscreen for the Lumia 950.
MSM8994 also gains USB and SDHCI support, as well as VADC and temp-alarm
support. Then support for the Lumia 950 XL is added.
SDM845 gains interconnect properties for a number of devices and the
GENI wrappers gains iommu stream configuration, which means DMA
operations on e.g. I2C now works. The Lenovo Yoga C630 finally has the
SMMU enabled, a few fixes and the description of the eDP bridge and
panel means that the laptop can now boot mainline with working display,
GPU, WiFi and audio.
SC7180 gains a slew of smaller improvements and fixes.
* tag 'qcom-arm64-for-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux: (93 commits)
arm64: dts: qcom: c630: Define eDP bridge and panel
arm64: dts: qcom: c630: Fix pinctrl pins properties
arm64: dts: qcom: c630: Polish i2c-hid devices
arm64: dts: qcom: sc7180: Add lpass cpu node for I2S driver
arm64: dts: sdm845: Add interconnect properties for QUP
interconnect: qcom: sdm845: Add the missing nodes for QUP
dt-bindings: interconnect: sdm845: Add IDs for the QUP ports
arm64: dts: qcom: c630: Expose LID events
arm64: dts: qcom: c630: Re-enable apps_smmu
dts: qcom: sdm845: Add dt entries to support crypto engine.
arm64: dts: qcom: qrb5165-rb5: Add support for MCP2518FD
arm64: dts: qcom: sdm845: use GIC_SPI for IPA interrupts
arm64: dts: qcom: sc7180: use GIC_SPI for IPA interrupts
arm64: dts: qcom: sc7180: limit IPA iommu streams
arm64: dts: qcom: sm8150: Add Coresight support
arm64: dts: qcom: sc7180-trogdor: Make pp3300_a the default supply for pp3300_hub
arm64: dts: qcom: sc7180: Add DDR/L3 votes for the pro variant
arm64: dts: qcom: sc7180-lite: Tweak DDR/L3 scaling on SC7180-lite
arm64: dts: qcom: sc7180-trogdor: add "pen-insert" label for trogdor
arm64: qcom: sc7180: trogdor: Add ADC nodes and thermal zone for charger thermistor
...
Link: https://lore.kernel.org/r/20201130190131.345187-1-bjorn.andersson@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Tue, 8 Dec 2020 22:47:04 +0000 (23:47 +0100)]
Merge tag 'ti-k3-dt-for-v5.11' of git://git./linux/kernel/git/nmenon/linux into arm/dt
Devicetree changes for TI K3 platforms for v5.11 merge window:
- Standardized usage of "disabled" only in board.dts files, #interrupt-cells warning fixups, node format error fixes
- J721E: R5F support, MMC/SD UHS mode added
- AM654: R5F support, dss marked coherent, drop unused dma-ring-reset-quirk property
- J7200: ADC support, Mailbox, hwspinlock
* tag 'ti-k3-dt-for-v5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/nmenon/linux: (25 commits)
arm64: dts: ti: k3-j721e-common-proc-board: Add support for SD card UHS modes
arm64: dts: ti: k3-j721e-main: Add output tap delay values
arm64: dts: ti: k3: squelch warning about lack of #interrupt-cells
arm64: dts: ti: k3-j7200-common-proc-board: Correct the name of io expander on main_i2c1
arm64: dts: ti: k3-j7200-som-p0: main_i2c0 have an ioexpander on the SOM
arm64: dts: ti: k3-j7200-som-p0: Add IPC sub-mailbox nodes
arm64: dts: ti: k3-j7200-main: Add mailbox cluster nodes
arm64: dts: ti: k3-j7200-main: Add hwspinlock node
arm64: dts: ti: am65/j721e/j7200: Mark firmware used uart as "reserved"
arm64: dts: ti: k3-am654-base-board: Fix up un-necessary status set to "okay" for USB
arm64: dts: ti: am65/j721e: Fix up un-necessary status set to "okay" for crypto
arm64: dts: ti: k3-j721e*: Cleanup disabled nodes at SoC dtsi level
arm64: dts: ti: k3-am65*: Cleanup disabled nodes at SoC dtsi level
arm64: dts: ti: k3-j7200-mcu-wakeup: Enable ADC support
arm64: dts: ti: k3-am65*/j721e*: Fix unit address format error for dss node
arm64: dts: ti: k3-j721e-som-p0: Add DDR carveout memory nodes for R5Fs
arm64: dts: ti: k3-j721e-som-p0: Add mailboxes to R5Fs
arm64: dts: ti: k3-j721e-main: Add MAIN domain R5F cluster nodes
arm64: dts: ti: k3-j721e-mcu: Add MCU domain R5F cluster node
arm64: dts: ti: k3-am654-base-board: Reserve memory for IPC between R5F cores
...
Link: https://lore.kernel.org/r/20201130174258.ljsiokkyr7x7tsbd@covenant
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Tue, 8 Dec 2020 22:45:58 +0000 (23:45 +0100)]
Merge tag 'mvebu-dt64-5.11-1' of git://git./linux/kernel/git/gclement/mvebu into arm/dt
mvebu dt64 for 5.11 (part 1)
- Add support for IEI Puzzle-M801 board (Armada 8040 based)
- Add support ESPRESSObin-Ultra (Armada 3720 based)
- Clean-up and improve espressobin device tree
- Switch to per-port SATA interrupts on CP110 based SoC
- Use compliant node name for USB3 on CP110 based SoC
- Add heartbeat LED on mcbin singleshot
- Disable SMMU by default for Armada 7040 and 8040 to continued
supporting custom bot firmware
- Turris mox:
- add 3W power capability to SFP cage
- update ethernet-phy handle name
* tag 'mvebu-dt64-5.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/gclement/mvebu:
arm64: dts: armada-3720-turris-mox: add 3W power capability to SFP cage
arm64: dts: marvell: keep SMMU disabled by default for Armada 7040 and 8040
arm64: dts: mcbin-singleshot: add heartbeat LED
arm64: dts: marvell: cp11x: Harmonize xHCI DT nodes name
arm64: dts: marvell: espressobin: Update link to V7 schematic
arm64: dts: armada-3720-turris-mox: update ethernet-phy handle name
arm64: dts: marvell: armada-cp110: Switch to per-port SATA interrupts
arm64: dts: marvell: add DT for ESPRESSObin-Ultra
arm64: dts: marvell: espressobin: Add support for LED2
arm64: dts: marvell: Add a device tree for the IEI Puzzle-M801 board
arm64: dts: marvell: espressobin: De-duplicate eMMC definitions
arm64: dts: marvell: espressobin: Get rid of duplicate serial aliases
arm64: dts: marvell: espressobin: Simplify v7 ethernet port labeling
Link: https://lore.kernel.org/r/87eekaj0i4.fsf@BL-laptop
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Tue, 8 Dec 2020 22:44:45 +0000 (23:44 +0100)]
Merge tag 'mvebu-dt-5.11-1' of git://git./linux/kernel/git/gclement/mvebu into arm/dt
mvebu dt for 5.11 (part 1)
- Add support for MikroTik CRS3xx switches
- Add support for RD-AC3X-48G4X2XL board : Armada 382 SoC connected
to Prestera AC3X ASIC through PCI
- Clean-up kirkwood device tree: replace "ok" by "okay"
- Improve device tree for PCA953x gpio expander nodes
- Use compliant node name for USB3 on armada 375
- 98dx3236 SoCs:
- remove non-existent i2c1
- add i2c0 pinctrl information
- Improve device tree for Turris Omnia
* tag 'mvebu-dt-5.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/gclement/mvebu:
ARM: dts: mvebu: Add device tree for RD-AC3X-48G4X2XL board
arm: dts: marvell: armada-375: Harmonize DWC USB3 DT nodes name
ARM: dts: turris-omnia: remove unneeded status = "okay" properties
ARM: dts: turris-omnia: update ethernet-phy node and handle name
ARM: dts: turris-omnia: add LED controller node
ARM: dts: turris-omnia: add SFP node
ARM: dts: turris-omnia: describe switch interrupt
ARM: dts: turris-omnia: add comphy handle to eth2
ARM: dts: turris-omnia: enable HW buffer management
ARM: dts: Add i2c0 pinctrl information for 98dx3236
ARM: dts: Remove non-existent i2c1 from 98dx3236
ARM: dts: armada: align GPIO hog names with dtschema
ARM: dts: dove: fix PCA95xx GPIO expander properties on A510
ARM: dts: kirkwood: replace status value "ok" by "okay"
ARM: dts: mvebu: Add CRS328-4C-20S-4S board
ARM: dts: mvebu: Add CRS305-1G-4S board
ARM: dts: mvebu: Add CRS326-24G-2S board
Link: https://lore.kernel.org/r/87h7p6j0m7.fsf@BL-laptop
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Tue, 8 Dec 2020 22:43:33 +0000 (23:43 +0100)]
Merge tag 'nuvoton-5.11-devicetree' of git://git./linux/kernel/git/joel/bmc into arm/dt
Nuvoton device tree updates for 5.11
- New machines
* Fii Kudo, a NPCM730 BMC
* Quanta GSJ, a NPCM750 BMC
* Qanta Olympus RunBMC, a NPCM750 BMC
- Updates to the common device trees and NCPM750 EVB
* tag 'nuvoton-5.11-devicetree' of git://git.kernel.org/pub/scm/linux/kernel/git/joel/bmc:
dt-bindings: vendor-prefixes: Add FII
ARM: dts: nuvoton: Add Fii Kudo system
ARM: dts: nuvoton: Add NPCM7xx RunBMC Olympus Quanta machine
ARM: dts: nuvoton: Add Quanta GSJ BMC
ARM: dts: nuvoton: Add Quanta GSJ BMC pinctrl
ARM: dts: nuvoton: Add Nuvoton NPCM730 device tree
ARM: dts: nuvoton: Add new device nodes to NPCM750 EVB
ARM: dts: nuvoton: Add new device nodes
ARM: dts: nuvoton: Add pinctrl and GPIO node
ARM: dts: nuvoton: Modify timer register size
ARM: dts: nuvoton: Modify clock parameters
Link: https://lore.kernel.org/r/CACPK8Xd8RaLv_p6t9ckBwCwtZww+2YYOAoAYQdvni0dxc2mS7A@mail.gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Tue, 8 Dec 2020 22:38:36 +0000 (23:38 +0100)]
Merge tag 'v5.10-next-dts64' of git://git./linux/kernel/git/matthias.bgg/linux into arm/dt
mt8173:
- add new power domain controller node
mt8183:
- add new power domain controller
- add display, iommu and dsi nodes
mt8192:
- add basic support, pinctrl, uart, spi, i2c and timer
mt8516:
- add auxadc, efuse and usb nodes
mt8167:
- add basic support for the SoC
- add support for the pumkin board
mt6779:
- add initial support, interrupt controller, clocks, uart
mt7622:
- PWM node for all available PWM channels
* tag 'v5.10-next-dts64' of git://git.kernel.org/pub/scm/linux/kernel/git/matthias.bgg/linux: (25 commits)
dts64: mt7622: disable spi1 and uart2 because pins are used by pwm
dts64: mt7622: enable all pwm for bananapi r64
arm64: dts: mt8183: Add display nodes for MT8183
arm64: dts: mt8183: Add iommu and larb nodes
arm64: dts: mt8183: Add dsi node
arm64: dts: mt8183: Add pwm and backlight node
arm64: dts: mediatek: Add mt8183 power domains controller
arm64: dts: mediatek: Add smi_common node for MT8183
arm64: dts: mediatek: Add mt8173 power domain controller
dt-bindings: power: Add MT8192 power domains
dt-bindings: power: Add MT8183 power domains
dt-bindings: power: Add bindings for the Mediatek SCPSYS power domains controller
arm64: dts: Add Mediatek SoC MT8192 and evaluation board dts and Makefile
arm64: dts: mediatek: add MT8167 pumpkin board dts
arm64: dts: mediatek: add dtsi for MT8167
dt-bindings: arm64: dts: mediatek: Add mt8167-pumpkin board
arm64: dts: mediatek: mt8516: add efuse node
arm64: dts: mediatek: align GPIO hog names with dtschema
arm64: dts: mediatek: mt8516: add usb1 node
arm64: dts: mediatek: mt8516: rename usb phy
...
Link: https://lore.kernel.org/r/72fe1c4f-f27c-c455-dfd9-66bde90bb295@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Tue, 8 Dec 2020 22:37:23 +0000 (23:37 +0100)]
Merge tag 'arm-soc/for-5.11/devicetree-arm64' of https://github.com/Broadcom/stblinux into arm/dt
This pull request contains Broadcom ARM64-based SoCs Device Tree changes
for 5.11, please pull the following:
- Rafal adds initial support for the Broadcom 4908 which are SoCs used
in home routers and are based on the DSL architecture and using
Broadcom Brahma-B53 CPUs.
* tag 'arm-soc/for-5.11/devicetree-arm64' of https://github.com/Broadcom/stblinux:
arm64: add config for Broadcom BCM4908 SoCs
arm64: dts: broadcom: add BCM4908 and Asus GT-AC5300 early DTS files
dt-bindings: arm: bcm: document BCM4908 bindings
Link: https://lore.kernel.org/r/20201128163410.1691529-4-f.fainelli@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Tue, 8 Dec 2020 22:36:21 +0000 (23:36 +0100)]
Merge tag 'arm-soc/for-5.11/devicetree' of https://github.com/Broadcom/stblinux into arm/dt
This pull request contains Broadcom ARM-based SoCs changes for 5.11,
please pull the following:
- Vivek updates the Linksys EA9500 DTS by adding the two additional
switch port nodes (5 & 7), providing a flash partition layout to
make the device usable with OpenWrt, and finally switches to using
the pin controller rather than using mdio-mux to get the same outcome.
- Serge fixes the USB Device Tree nodes unit name to be conformant to
the recommended name patterns.
- Rafal re-arranges all the nodes that belonged to the CRU block to be
under the CRU node (such as PLLs). He also disables the USB3 PHY node
for devices that lack USB3 and adds USB3 support to the Luxul XWR-3150
DTS.
- Jonathan drops the incorrect 'io-channel-ranges' from the Cygnus SoC
DTSI.
- Maxime disables the Wi-Fi frequencies (around 2.4GHz) for HDMI on the
Raspberry Pi 4 due to some cross-talk between the two blocks.
- Pavel updates the DWC2 USB controller RX FIFO sizes to be more
accurate for all BCM283x (Raspberr Pi) SoCs.
- Florian updates all BCM5301x and NSP Device Tree files to allow
switching the Broadcom B53 Ethernet switch device tree binding to YAML.
* tag 'arm-soc/for-5.11/devicetree' of https://github.com/Broadcom/stblinux: (22 commits)
dt-bindings: net: dsa: b53: Add YAML bindings
ARM: dts: NSP: Provide defaults ports container node
ARM: dts: NSP: Add a SRAB compatible string for each board
ARM: dts: NSP: Fix Ethernet switch SGMII register name
ARM: dts: NSP: Update ethernet switch node name
ARM: dts: BCM5301X: Provide defaults ports container node
ARM: dts: BCM5301X: Add a default compatible for switch node
ARM: dts: BCM5301X: Update Ethernet switch node name
dt-bindings: net: dsa: Document sfp and managed properties
dt-bindings: net: dsa: Extend switch nodes pattern
ARM: dts: bcm283x: increase dwc2's RX FIFO size
ARM: dts: rpi-4: disable wifi frequencies
ARM: dts: Cygnus: Drop incorrect io-channel-ranges property.
ARM: dts: BCM5301X: Enable USB 3 PHY on Luxul XWR-3150
ARM: dts: BCM5301X: Disable USB 3 PHY on devices without USB 3
ARM: dts: BCM5301X: Move CRU devices to the CRU node
ARM: dts: BCM5301X: Linksys EA9500 make use of pinctrl
ARM: dts: BCM5301X: Use corretc pinctrl compatible for 4709x
ARM: dts: BCM5301X: Linksys EA9500 add fixed partitions
ARM: dts: BCM5310X: Harmonize xHCI DT nodes name
...
Link: https://lore.kernel.org/r/20201128163410.1691529-3-f.fainelli@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Tue, 8 Dec 2020 22:34:45 +0000 (23:34 +0100)]
Merge tag 'sunxi-dt-for-5.11' of git://git./linux/kernel/git/sunxi/linux into arm/dt
Our usual bunch of patches to support the Allwinner SoCs, this time
adding:
- Some nice pinephone additions
- I2S support for the A64, H3, H5 and H6
- New boards: Elimo Impetus, Elimo Initium, FriendlyArm ZeroPi, NanoPi R1
* tag 'sunxi-dt-for-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux: (21 commits)
ARM: dts: sun8i-h2-plus-bananapi-m2-zero: add gpio-line-names
ARM: dts: sun8i: h3: Add initial NanoPi R1 support
arm64: dts: allwinner: pinephone: Use generic sensor node names
ARM: dts: sun8i: s3: Add dts for the Elimo Initium SBC
dt-bindings: arm: sunxi: add Elimo bindings
ARM: dts: sun8i: s3: Add dtsi for the Elimo Impetus SoM
arm64: dts: allwinner: pinephone: Add Bluetooth support
arm64: dts: allwinner: pinephone: Add WiFi support
arm64: dts: allwinner: pinephone: Add light/proximity sensor
arm64: dts: allwinner: pinephone: Add LED flash
arm64: dts: allwinner: pinephone: Set ALDO3 to exactly 3v0
arm64: dts: allwinner: pinephone: Remove AC power supply
arm: dts: sunxi: h3/h5: Add I2S2 node
arm64: dts: allwinner: a64: Add I2S2 node
arm64: dts: allwinner: h6: Add I2S1 node
arm64: dts: allwinner: h6: PineH64 model B: Add wifi
ARM: dts: sun8i-v3s: Add I2C1 PB pins description
ARM: dts: sun8i: V3/S3: Add UART1 pin definitions to the V3/S3 dtsi
dt-bindings: vendors: add Elimo Engineering vendor prefix
ARM: dts: sun8i: add FriendlyArm ZeroPi support
...
Link: https://lore.kernel.org/r/551fdf4f-8a0b-4a22-ba49-b4f61520a9ab.lettre@localhost
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Tue, 8 Dec 2020 22:33:36 +0000 (23:33 +0100)]
Merge tag 'at91-dt-5.11' of git://git./linux/kernel/git/at91/linux into arm/dt
AT91 DT for 5.11:
- fix USB host pinctrl
- fix DT schema warnings
* tag 'at91-dt-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/at91/linux:
ARM: dts: at91: sama5d3_xplained: add pincontrol for USB Host
ARM: dts: at91: sama5d4_xplained: add pincontrol for USB Host
ARM: dts: at91: sam9x60: add pincontrol for USB Host
ARM: dts: at91: at91-sama5d27_som1: fix EEPROM compatible
ARM: dts: at91: Fix schema warnings for pwm-leds
ARM: dts: at91: smartkiz: Reference led node directly
Link: https://lore.kernel.org/r/20201127220403.GA1735041@piout.net
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Bjorn Andersson [Sat, 28 Nov 2020 03:42:31 +0000 (21:42 -0600)]
arm64: dts: qcom: c630: Define eDP bridge and panel
The Lenovo Yoga C630 drives the Boe NV133FHM-N61 eDP display from DSI
using a TI SN65DSI86 bridge chip on I2C 10. Define the bridge and eDP
panel and enable the display blocks.
Tested-by: Steev Klimaszewski <steev@kali.org>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Link: https://lore.kernel.org/r/20201128034231.89750-1-bjorn.andersson@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Bjorn Andersson [Mon, 30 Nov 2020 17:00:28 +0000 (11:00 -0600)]
arm64: dts: qcom: c630: Fix pinctrl pins properties
The "pins" property takes an array of pin _names_, not pin numbers. Fix
this.
Tested-by: Steev Klimaszewski <steev@kali.org>
Fixes:
44acee207844 ("arm64: dts: qcom: Add Lenovo Yoga C630")
Link: https://lore.kernel.org/r/20201130170028.319798-1-bjorn.andersson@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Bjorn Andersson [Mon, 30 Nov 2020 16:59:24 +0000 (10:59 -0600)]
arm64: dts: qcom: c630: Polish i2c-hid devices
The numbering of the i2c busses differs from ACPI and a number of typos
was made in the original patch. Further more the irq flags for the
various resources was not correct and i2c3 only has one of the two
client devices active in any one device.
Also label the various devices, for easier comparison with the ACPI
tables.
Tested-by: Steev Klimaszewski <steev@kali.org>
Fixes:
44acee207844 ("arm64: dts: qcom: Add Lenovo Yoga C630")
Link: https://lore.kernel.org/r/20201130165924.319708-1-bjorn.andersson@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Ajit Pandey [Fri, 18 Sep 2020 17:33:46 +0000 (23:03 +0530)]
arm64: dts: qcom: sc7180: Add lpass cpu node for I2S driver
Add the I2S controller node to sc7180 dtsi.
Add pinmux for primary and secondary I2S.
Reviewed-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Ajit Pandey <ajitp@codeaurora.org>
Signed-off-by: Cheng-Yi Chiang <cychiang@chromium.org>
Signed-off-by: V Sujith Kumar Reddy <vsujithk@codeaurora.org>
Signed-off-by: Srinivasa Rao Mandadapu <srivasam@codeaurora.org>
Link: https://lore.kernel.org/r/1600450426-14063-1-git-send-email-srivasam@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Kathiravan T [Mon, 30 Nov 2020 11:01:45 +0000 (16:31 +0530)]
arm64: dts: ipq6018: Add the QPIC peripheral nodes
Add the QPIC BAM and QPIC NAND controller support and
enable the same in board DTS file.
Co-developed-by: Anusha Canchi Ramachandra Rao <anusharao@codeaurora.org>
Signed-off-by: Anusha Canchi Ramachandra Rao <anusharao@codeaurora.org>
Signed-off-by: Kathiravan T <kathirav@codeaurora.org>
Link: https://lore.kernel.org/r/1606734105-12414-2-git-send-email-kathirav@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Georgi Djakov [Thu, 5 Nov 2020 13:52:11 +0000 (15:52 +0200)]
arm64: dts: sdm845: Add interconnect properties for QUP
Add the interconnects DT property to describe the ports for GENI QUPs
on the sdm845 platform.
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Link: https://lore.kernel.org/r/20201105135211.7160-3-georgi.djakov@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Georgi Djakov [Thu, 5 Nov 2020 13:52:10 +0000 (15:52 +0200)]
interconnect: qcom: sdm845: Add the missing nodes for QUP
The QUP nodes are currently defined just as entries in the topology,
but they are not referenced by any of the NoCs. Let's fix this and
"attach" them to their NoCs, so that the QUP drivers are able to use
them as path endpoints and scale their bandwidth.
This is based on the information from the downstream msm-4.9 kernel.
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Link: https://lore.kernel.org/r/20201105135211.7160-2-georgi.djakov@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Georgi Djakov [Thu, 5 Nov 2020 13:52:09 +0000 (15:52 +0200)]
dt-bindings: interconnect: sdm845: Add IDs for the QUP ports
The QUP ports exist in the topology, but are not exposed as an
endpoints in DT. Fix this by creating IDs and attach them to their
NoCs, so that the various QUP drivers (i2c/spi/uart etc.) are able
to request their interconnect paths and scale their bandwidth.
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Link: https://lore.kernel.org/r/20201105135211.7160-1-georgi.djakov@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Bjorn Andersson [Wed, 25 Nov 2020 06:08:38 +0000 (00:08 -0600)]
arm64: dts: qcom: c630: Expose LID events
The LID state can be read from GPIO 124 and the "tablet mode" from GPIO
95, expose these to the system using gpio-keys and mark the falling edge
of the LID state as a wakeup-source - to wake the system from suspend.
Tested-by: Steev Klimaszewski <steev@kali.org>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Link: https://lore.kernel.org/r/20201125060838.165576-1-bjorn.andersson@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Bjorn Andersson [Tue, 24 Nov 2020 18:44:14 +0000 (12:44 -0600)]
arm64: dts: qcom: c630: Re-enable apps_smmu
Re-enable the apps_smmu now that the arm-smmu driver supports stream
mapping handoff from firmware.
Tested-by: Steev Klimaszewski <steev@kali.org>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Link: https://lore.kernel.org/r/20201124184414.380796-1-bjorn.andersson@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Thara Gopinath [Thu, 19 Nov 2020 15:52:32 +0000 (10:52 -0500)]
dts: qcom: sdm845: Add dt entries to support crypto engine.
Add crypto engine (CE) and CE BAM related nodes and definitions to
"sdm845.dtsi".
Signed-off-by: Thara Gopinath <thara.gopinath@linaro.org>
Link: https://lore.kernel.org/r/20201119155233.3974286-6-thara.gopinath@linaro.org
[bjorn: Replaced RPMH_CE_CLK constant, for now]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Marek Behún [Mon, 16 Nov 2020 12:33:03 +0000 (13:33 +0100)]
arm64: dts: armada-3720-turris-mox: add 3W power capability to SFP cage
Add maximum-power-milliwatt = 3000 to SFP node of Turris MOX.
Signed-off-by: Marek Behún <kabel@kernel.org>
Fixes:
7109d817db2e ("arm64: dts: marvell: add DTS for Turris Mox")
Cc: Gregory CLEMENT <gregory.clement@bootlin.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: devicetree@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Tomasz Nowicki [Thu, 5 Nov 2020 11:26:02 +0000 (12:26 +0100)]
arm64: dts: marvell: keep SMMU disabled by default for Armada 7040 and 8040
FW has to configure devices' StreamIDs so that SMMU is able to lookup
context and do proper translation later on. For Armada 7040 & 8040 and
publicly available FW, most of the devices are configured properly,
but some like ap_sdhci0, PCIe, NIC still remain unassigned which
results in SMMU faults about unmatched StreamID (assuming
ARM_SMMU_DISABLE_BYPASS_BY_DEFAUL=y).
Since there is dependency on custom FW let SMMU be disabled by default.
People who still willing to use SMMU need to enable manually and
use ARM_SMMU_DISABLE_BYPASS_BY_DEFAUL=n (or via kernel command line)
with extra caution.
Fixes:
83a3545d9c37 ("arm64: dts: marvell: add SMMU support")
Cc: <stable@vger.kernel.org> # 5.9+
Signed-off-by: Tomasz Nowicki <tn@semihalf.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Tomasz Maciej Nowak [Tue, 10 Nov 2020 15:38:31 +0000 (16:38 +0100)]
arm64: dts: mcbin-singleshot: add heartbeat LED
With board revision 1.3, SolidRun moved the power LED to the middle of
the board. In old place of power LED a GPIO controllable heartbeat LED
was added. This commit only touches Single Shot variant, since only this
variant is all revision 1.3.
Reported-by: Alexandra Alth <alexandra@alth.de>
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Serge Semin [Wed, 11 Nov 2020 09:15:45 +0000 (12:15 +0300)]
arm64: dts: marvell: cp11x: Harmonize xHCI DT nodes name
In accordance with the Generic xHCI bindings the corresponding node
name is suppose to comply with the Generic USB HCD DT schema, which
requires the USB nodes to have the name acceptable by the regexp:
"^usb(@.*)?" . Make sure the "generic-xhci"-compatible nodes are
correctly named.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Aryan Srivastava [Thu, 26 Nov 2020 04:45:44 +0000 (17:45 +1300)]
ARM: dts: mvebu: Add device tree for RD-AC3X-48G4X2XL board
Add device tree for RD-AC3X-48G4X2XL board. This has a Armada 382 SoC on
a interposer board connected to a baseboard with a Prestera AC3X ASIC
connected via PCI.
Signed-off-by: Aryan Srivastava <aryan.srivastava@alliedtelesis.co.nz>
Reviewed-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Serge Semin [Wed, 11 Nov 2020 09:15:46 +0000 (12:15 +0300)]
arm: dts: marvell: armada-375: Harmonize DWC USB3 DT nodes name
In accordance with the DWC USB3 bindings the corresponding node
name is suppose to comply with the Generic USB HCD DT schema, which
requires the USB nodes to have the name acceptable by the regexp:
"^usb(@.*)?" . Make sure the "snps,dwc3"-compatible nodes are correctly
named.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Faiz Abbas [Sun, 29 Nov 2020 17:52:23 +0000 (23:22 +0530)]
arm64: dts: ti: k3-j721e-common-proc-board: Add support for SD card UHS modes
Add support for UHS modes for the SD card connected at sdhci1. This
involves adding regulators for voltage switching and power cycling the
SD card and removing the no-1-8-v property.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20201129175223.21751-3-nsekhar@ti.com
Faiz Abbas [Sun, 29 Nov 2020 17:52:22 +0000 (23:22 +0530)]
arm64: dts: ti: k3-j721e-main: Add output tap delay values
Add output tap delay values as given in the latest Data Manual[1],
SPRSP36E, revised December 2019.
[1] https://www.ti.com/lit/gpn/tda4vm
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20201129175223.21751-2-nsekhar@ti.com
Marek Behún [Sun, 15 Nov 2020 13:59:23 +0000 (14:59 +0100)]
ARM: dts: turris-omnia: remove unneeded status = "okay" properties
Only nodes which have status = "disabled" defined from included files
need status = "okay".
The ethernet-phy node and the i2cmux node do not need it, since they are
wholly defined here.
Signed-off-by: Marek Behún <kabel@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Uwe Kleine-König <uwe@kleine-koenig.org>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Gregory CLEMENT <gregory.clement@bootlin.com>
Cc: Andreas Färber <afaerber@suse.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: devicetree@vger.kernel.org
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Marek Behún [Sun, 15 Nov 2020 13:59:22 +0000 (14:59 +0100)]
ARM: dts: turris-omnia: update ethernet-phy node and handle name
Use property name `phy-handle` instead of the deprecated `phy` to
connect eth2 to the PHY.
Rename the node from "phy@1" to "ethernet-phy@1", since "phy@1" is
incorrect according to device-tree bindings documentation.
Also remove the "ethernet-phy-id0141.0DD1" compatible string, it is not
needed. Kernel can read the PHY identifier itself.
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Uwe Kleine-König <uwe@kleine-koenig.org>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Gregory CLEMENT <gregory.clement@bootlin.com>
Cc: Andreas Färber <afaerber@suse.de>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: devicetree@vger.kernel.org
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Marek Behún [Sun, 15 Nov 2020 13:59:21 +0000 (14:59 +0100)]
ARM: dts: turris-omnia: add LED controller node
Linux now has incomplete support for the LED controller on Turris Omnia:
it can set brightness and colors for each LED.
The controller can also put these LEDs into HW controlled mode, in which
the LEDs are controlled by HW: for example the WAN LED is connected via
MCU to the WAN PHY LED pin.
The driver does not support these HW controlled modes yet, and on probe
puts the LEDs into SW controlled mode.
Add node describing the LED controller, but disable it for now.
Signed-off-by: Marek Behún <kabel@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Uwe Kleine-König <uwe@kleine-koenig.org>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Gregory CLEMENT <gregory.clement@bootlin.com>
Cc: Andreas Färber <afaerber@suse.de>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: devicetree@vger.kernel.org
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Marek Behún [Mon, 16 Nov 2020 12:24:22 +0000 (13:24 +0100)]
ARM: dts: turris-omnia: add SFP node
Turris Omnia has an SFP cage that, together with WAN PHY, is connected
to eth2 SerDes via a SerDes multiplexor. When a SFP module is present,
the multiplexor switches the SerDes signal from PHY to SFP.
Describe the SFP cage, but leave it disabled. Until phylink has support
for such configuration, we are leaving it to U-Boot to enable SFP and
disable WAN PHY at boot time depending on whether a SFP module is
present.
Signed-off-by: Marek Behún <kabel@kernel.org>
Fixes:
26ca8b52d6e1 ("ARM: dts: add support for Turris Omnia")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Cc: Russell King - ARM Linux admin <linux@armlinux.org.uk>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Uwe Kleine-König <uwe@kleine-koenig.org>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Gregory CLEMENT <gregory.clement@bootlin.com>
Cc: Andreas Färber <afaerber@suse.de>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: devicetree@vger.kernel.org
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Marek Behún [Sun, 15 Nov 2020 13:59:19 +0000 (14:59 +0100)]
ARM: dts: turris-omnia: describe switch interrupt
Describe switch interrupt for Turris Omnia so that the CPU does not have
to poll the switch. We also need to to set mpp45 pin to gpio function
for this.
Signed-off-by: Marek Behún <kabel@kernel.org>
Fixes:
26ca8b52d6e1 ("ARM: dts: add support for Turris Omnia")
Cc: linux-arm-kernel@lists.infradead.org
Cc: Uwe Kleine-König <uwe@kleine-koenig.org>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Gregory CLEMENT <gregory.clement@bootlin.com>
Cc: Andreas Färber <afaerber@suse.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: devicetree@vger.kernel.org
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Marek Behún [Sun, 15 Nov 2020 13:59:18 +0000 (14:59 +0100)]
ARM: dts: turris-omnia: add comphy handle to eth2
The eth2 controller on Turris Omnia is connected to SerDes. For SFP to
be able to switch between 1G and 2.5G modes the comphy link has to be
defined.
Signed-off-by: Marek Behún <kabel@kernel.org>
Fixes:
f3a6a9f3704a ("ARM: dts: add description for Armada 38x ...")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Uwe Kleine-König <uwe@kleine-koenig.org>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Gregory CLEMENT <gregory.clement@bootlin.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: devicetree@vger.kernel.org
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Marek Behún [Sun, 15 Nov 2020 13:59:17 +0000 (14:59 +0100)]
ARM: dts: turris-omnia: enable HW buffer management
The buffer manager is available on Turris Omnia but needs to be
described in device-tree to be used.
Signed-off-by: Marek Behún <kabel@kernel.org>
Fixes:
26ca8b52d6e1 ("ARM: dts: add support for Turris Omnia")
Cc: linux-arm-kernel@lists.infradead.org
Cc: Uwe Kleine-König <uwe@kleine-koenig.org>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Gregory CLEMENT <gregory.clement@bootlin.com>
Cc: Andreas Färber <afaerber@suse.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: devicetree@vger.kernel.org
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Pali Rohár [Mon, 5 Oct 2020 13:35:13 +0000 (15:35 +0200)]
arm64: dts: marvell: espressobin: Update link to V7 schematic
Up-to-date version of V7 schematic is on new URL linked from official
tech-spec webpage http://espressobin.net/tech-spec/
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Joel Stanley [Thu, 19 Nov 2020 07:32:30 +0000 (18:02 +1030)]
dt-bindings: vendor-prefixes: Add FII
Adds Foxconn Industrial Internet, who have submitted a BMC device tree.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Benjamin Fair <benjaminfair@google.com>
Link: https://lore.kernel.org/r/20201119073230.123888-1-joel@jms.id.au
Signed-off-by: Joel Stanley <joel@jms.id.au>
Marek Behún [Sat, 14 Nov 2020 20:42:53 +0000 (21:42 +0100)]
arm64: dts: armada-3720-turris-mox: update ethernet-phy handle name
Use property name `phy-handle` instead of the deprecated `phy` to
connect eth2 to the PHY.
Signed-off-by: Marek Behún <kabel@kernel.org>
Fixes:
7109d817db2e ("arm64: dts: marvell: add DTS for Turris Mox")
Cc: Gregory CLEMENT <gregory.clement@bootlin.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: devicetree@vger.kernel.org
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Sven Auhagen [Mon, 9 Nov 2020 17:39:48 +0000 (18:39 +0100)]
arm64: dts: marvell: armada-cp110: Switch to per-port SATA interrupts
There are two SATA ports per CP110. Each of them has a dedicated
interrupt. Describe the real hardware by adding two SATA ports to the
CP110 SATA node.
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sven Auhagen <sven.auhagen@voleatech.de>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Vladimir Vid [Mon, 26 Oct 2020 18:44:42 +0000 (19:44 +0100)]
arm64: dts: marvell: add DT for ESPRESSObin-Ultra
This adds support for ESPRESSObin-Ultra from Globalscale.
Specifications are similar to the base ESPRESSObin board, with main
difference being being WAN port with PoE capability and 2 additional ethernet ports.
Full specifications:
1x Marvell 64 bit Dual Core ARM A53 Armada 3700 SOC clocked up to 1.2Ghz
1x Topaz 6341 Networking Switch
1GB DDR4
8GB eMMC
1x WAN with 30W POE
4x Gb LAN
1x RTC Clock and battery
1x DC Jack
1x USB 3.0 Type A
1x USB 2.0 Type A
1x SIM NanoSIM card Slot
1x Power Button
4x LED
1x Reset button
1x microUSB for UART
1x M.2 2280 slot for memory
1x 2x2 802.11ac Wi-Fi
1x MiniPCIE slot for Wi-Fi (PCIe interface)
Signed-off-by: Vladimir Vid <vladimir.vid@sartura.hr>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Pali Rohár [Tue, 6 Oct 2020 12:44:55 +0000 (14:44 +0200)]
arm64: dts: marvell: espressobin: Add support for LED2
LED2 is connected to MPP1_2 pin. It is working only on V7 boards.
V5 boards have hw bug which cause that LED2 is non-working.
So enable LED2 only for Espressobin V7 boards.
Note that LED1 is connected to LED_WLAN# pin on miniPCIe card and LED3 to
power supply. Therefore on Espressobin board only LED2 can be controlled
directly from the host. LED1 is possible to control via WiFi card inserted
in miniPCIe slot if driver for particular card supports it.
Signed-off-by: Pali Rohár <pali@kernel.org>
Tested-by: Gérald Kerma <gerald@gk2.net>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Luka Kovacic [Sun, 25 Oct 2020 01:13:51 +0000 (02:13 +0100)]
arm64: dts: marvell: Add a device tree for the IEI Puzzle-M801 board
Add initial support for the IEI Puzzle-M801 1U Rackmount Network
Appliance board.
The board is based on the quad-core Marvell Armada 8040 SoC and supports
up to 16 GB of DDR4 2400 MHz ECC RAM. It has a PCIe x16 slot (x2 lanes
only) and an M.2 type B slot.
Main system hardware:
2x USB 3.0
4x Gigabit Ethernet
2x SFP+
1x SATA 3.0
1x M.2 type B
1x RJ45 UART
1x SPI flash
1x IEI WT61P803 PUZZLE Microcontroller
1x EPSON RX8010 RTC (used instead of the integrated Marvell RTC controller)
6x SFP+ LED
1x HDD LED
All of the hardware listed above is supported and tested in this port.
Signed-off-by: Luka Kovacic <luka.kovacic@sartura.hr>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Robert Marko <robert.marko@sartura.hr>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Pali Rohár [Fri, 25 Sep 2020 08:50:43 +0000 (10:50 +0200)]
arm64: dts: marvell: espressobin: De-duplicate eMMC definitions
eMMC definitions in files armada-3720-espressobin-emmc.dts and
armada-3720-espressobin-v7-emmc.dts is same. So move it into common
armada-3720-espressobin.dtsi file with status "disabled".
This change simplifies eMMC variants of DTS files for Espressobin.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Andre Heider <a.heider@gmail.com>
Tested-by: Andre Heider <a.heider@gmail.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Andre Heider [Tue, 22 Sep 2020 04:31:41 +0000 (06:31 +0200)]
arm64: dts: marvell: espressobin: Get rid of duplicate serial aliases
The included armada-37xx.dtsi already defines these two aliases.
Signed-off-by: Andre Heider <a.heider@gmail.com>
Reviewed-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Andre Heider [Tue, 8 Sep 2020 07:30:50 +0000 (09:30 +0200)]
arm64: dts: marvell: espressobin: Simplify v7 ethernet port labeling
Now that the switch ports have a label in the .dtsi, simplify the whole
"switch0" block for the v7 dts files.
Signed-off-by: Andre Heider <a.heider@gmail.com>
Reviewed-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Chris Packham [Mon, 7 Sep 2020 21:17:12 +0000 (09:17 +1200)]
ARM: dts: Add i2c0 pinctrl information for 98dx3236
Add pinctrl information for the 98dx3236 (and variants). There is only
one choice for i2c0 MPP14 and MPP15.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Chris Packham [Mon, 7 Sep 2020 21:17:11 +0000 (09:17 +1200)]
ARM: dts: Remove non-existent i2c1 from 98dx3236
The switches with integrated CPUs have only got a single i2c controller.
They incorrectly gained one when they were split from the Armada-XP.
Fixes:
43e28ba87708 ("ARM: dts: Use armada-370-xp as a base for armada-xp-98dx3236")
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Krzysztof Kozlowski [Wed, 16 Sep 2020 15:57:14 +0000 (17:57 +0200)]
ARM: dts: armada: align GPIO hog names with dtschema
The convention for node names is to use hyphens, not underscores.
dtschema for pca95xx expects GPIO hogs to end with 'hog' prefix.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Krzysztof Kozlowski [Wed, 16 Sep 2020 15:57:13 +0000 (17:57 +0200)]
ARM: dts: dove: fix PCA95xx GPIO expander properties on A510
The PCA95xx GPIO expander requires GPIO controller properties to operate
properly.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Adrian Schmutzler [Sun, 30 Aug 2020 19:35:43 +0000 (21:35 +0200)]
ARM: dts: kirkwood: replace status value "ok" by "okay"
While the DT parser recognizes "ok" as a valid value for the
"status" property, it is actually mentioned nowhere. Use the
proper value "okay" instead, as done in the majority of files
already.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Luka Kovacic [Fri, 24 Jul 2020 10:38:39 +0000 (12:38 +0200)]
ARM: dts: mvebu: Add CRS328-4C-20S-4S board
MikroTik CRS328-4C-20S-4S board has a switch chip with an integrated
Marvell Prestera 98DX3236 CPU.
This commit includes two board variants, namely the factory
default one and a Bit variant. The Bit variant has a
bigger Macronix flash.
This device tree includes basic Linux support.
Signed-off-by: Luka Kovacic <luka.kovacic@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Jakov Petrina <jakov.petrina@sartura.hr>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Luka Kovacic [Fri, 24 Jul 2020 10:38:38 +0000 (12:38 +0200)]
ARM: dts: mvebu: Add CRS305-1G-4S board
MikroTik CRS305-1G-4S board has a switch chip with an integrated
Marvell Prestera 98DX3236 CPU.
This commit includes two board variants, namely the factory
default one and a Bit variant. The Bit variant has a
bigger Macronix flash.
This device tree includes basic Linux support.
Signed-off-by: Luka Kovacic <luka.kovacic@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Jakov Petrina <jakov.petrina@sartura.hr>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Luka Kovacic [Fri, 24 Jul 2020 10:38:37 +0000 (12:38 +0200)]
ARM: dts: mvebu: Add CRS326-24G-2S board
MikroTik CRS326-24G-2S board has a switch chip with an integrated
Marvell Prestera 98DX3236 CPU.
This commit includes two board variants, namely the factory
default one and a Bit variant. The Bit variant has a
bigger Macronix flash.
This device tree includes basic Linux support.
Signed-off-by: Luka Kovacic <luka.kovacic@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Jakov Petrina <jakov.petrina@sartura.hr>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Manivannan Sadhasivam [Fri, 27 Nov 2020 17:30:44 +0000 (23:00 +0530)]
arm64: dts: qcom: qrb5165-rb5: Add support for MCP2518FD
Add support for onboard MCP2518FD SPI CAN transceiver attached to SPI0
of RB5.
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20201127173044.55144-1-manivannan.sadhasivam@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Jonathan Cameron [Sun, 15 Nov 2020 19:29:48 +0000 (19:29 +0000)]
ARM: dts: qcom-pma8084: Drop incorrect use of io-channel-ranges
This property is used by io-channel consumers, not providers so should
not present here. Note dt_schema will now detect this error as there
is a dependency between this property and io-channels.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Andy Gross <andy.gross@linaro.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20201115192951.1073632-7-jic23@kernel.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Sekhar Nori [Fri, 27 Nov 2020 21:01:28 +0000 (02:31 +0530)]
arm64: dts: ti: k3: squelch warning about lack of #interrupt-cells
There are couple of places where INTA interrupt controller
lacks #interrupt-cells property. This leads to warnings of
the type:
arch/arm64/boot/dts/ti/k3-j721e-main.dtsi:147.51-156.5: Warning (interrupt_provider): /bus@100000/main-navss/interrupt-controller@
33d00000: Missing #interrupt-cells in interrupt provider
when building TI device-tree files with W=2 warning level.
Fix these.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Link: https://lore.kernel.org/r/20201127210128.9151-1-nsekhar@ti.com
Arnd Bergmann [Fri, 27 Nov 2020 17:05:15 +0000 (18:05 +0100)]
Merge tag 'tegra-for-5.11-arm64-dt' of git://git./linux/kernel/git/tegra/linux into arm/dt
arm64: tegra: Device tree changes for v5.11-rc1
These changes are mostly minor fixes across the board, but they also
enable PMUs on Tegra186 and enable SATA support on Jetson TX2.
* tag 'tegra-for-5.11-arm64-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
arm64: tegra: Fix Tegra194 HDA {clock,reset}-names ordering
arm64: tegra: Enable AHCI on Jetson TX2
arm64: tegra: Change order of SATA resets for Tegra132 and Tegra210
arm64: tegra: Add XUSB pad controller interrupt
arm64: tegra: Rename ADMA device nodes for Tegra210
arm64: tegra: Hook up edp interrupt on Tegra132 SOCTHERM
arm64: tegra: Add missing hot temperatures to Tegra210 thermal-zones
arm64: tegra: Add missing gpu-throt-level to Tegra210 soctherm
arm64: tegra: Add missing hot temperatures to Tegra132 thermal-zones
arm64: tegra: Fix DT binding for IO High Voltage entry
arm64: tegra: Fix GIC400 missing GICH/GICV register regions
arm64: tegra: Add missing CPU PMUs on Tegra186
arm64: tegra: Fix Tegra234 VDK node names
arm64: tegra: Wrong AON HSP reg property size
arm64: tegra: Fix USB_VBUS_EN0 regulator on Jetson TX1
arm64: tegra: Correct the UART for Jetson Xavier NX
arm64: tegra: Disable the ACONNECT for Jetson TX2
Link: https://lore.kernel.org/r/20201127144329.124891-5-thierry.reding@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Fri, 27 Nov 2020 17:04:28 +0000 (18:04 +0100)]
Merge tag 'tegra-for-5.11-arm-dt' of git://git./linux/kernel/git/tegra/linux into arm/dt
ARM: tegra: Device tree changes for v5.11-rc1
This adds support for the Tegra30-based Ouya game console and enhances a
number of existing device trees. It also fixes a couple of minor issues
that were found during DT validation.
* tag 'tegra-for-5.11-arm-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux: (23 commits)
ARM: tegra: Add EMC OPP and ICC properties to Tegra124 EMC and ACTMON device-tree nodes
ARM: tegra: Add EMC OPP and ICC properties to Tegra30 EMC and ACTMON device-tree nodes
ARM: tegra: Add EMC OPP properties to Tegra20 device-trees
ARM: tegra: Add nvidia,memory-controller phandle to Tegra20 EMC device-tree
ARM: tegra: Add interconnect properties to Tegra124 device-tree
ARM: tegra: Add interconnect properties to Tegra30 device-tree
ARM: tegra: Add interconnect properties to Tegra20 device-tree
ARM: tegra: acer-a500: Add Embedded Controller
ARM: tegra: Change order of SATA resets for Tegra124
ARM: tegra: Correct EMC registers size in Tegra20 device-tree
ARM: tegra: Properly align clocks for SOCTHERM
ARM: tegra: Hook up edp interrupt on Tegra124 SOCTHERM
ARM: tegra: Add missing hot temperatures to Tegra124 thermal-zones
ARM: tegra: Add missing gpu-throt-level to Tegra124 soctherm
ARM: tegra: Populate OPP table for Tegra20 Ventana
ARM: tegra: nexus7: Use panel-lvds as the only panel compatible
ARM: tegra: nexus7: Rename gpio-hog nodes
ARM: tegra: nexus7: Add power-supply to lvds-encoder node
ARM: tegra: nexus7: Improve CPU passive-cooling threshold
ARM: tegra: nexus7: Correct thermal zone names
...
Link: https://lore.kernel.org/r/20201127144329.124891-4-thierry.reding@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Fri, 27 Nov 2020 17:03:16 +0000 (18:03 +0100)]
Merge tag 'tegra-for-5.11-dt-bindings' of git://git./linux/kernel/git/tegra/linux into arm/dt
dt-bindings: Changes for v5.11-rc1
This contains a couple of conversions of bindings to json-schema, as
well as symbolic names for the various memory clients on Tegra20,
Tegra30 and Tegra124. There's also a couple of fixes for Tegra194
pinmux and ARM GIC bindings. Finally, a new vendor prefix is added
for Ouya and the Ouya game console compatible string is defined.
* tag 'tegra-for-5.11-dt-bindings' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
dt-bindings: bus: Convert ACONNECT doc to json-schema
dt-bindings: interrupt-controller: arm,gic: Update Tegra compatibles
dt-bindings: dma: Convert ADMA doc to json-schema
dt-bindings: Fix entry name for I/O High Voltage property
dt-bindings: ARM: tegra: Add Ouya game console
dt-bindings: Add vendor prefix for Ouya Inc.
dt-bindings: memory: tegra124: Add memory client IDs
dt-bindings: memory: tegra30: Add memory client IDs
dt-bindings: memory: tegra20: Add memory client IDs
Link: https://lore.kernel.org/r/20201127144329.124891-1-thierry.reding@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Fri, 27 Nov 2020 17:02:45 +0000 (18:02 +0100)]
Merge tag 'renesas-arm-dt-for-v5.11-tag2' of git://git./linux/kernel/git/geert/renesas-devel into arm/dt
Renesas ARM DT updates for v5.11 (take two)
- PCIe endpoint support for the R-Car H3 ES2.0+ SoC.
* tag 'renesas-arm-dt-for-v5.11-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel:
arm64: dts: renesas: r8a77951: Add PCIe EP nodes
Link: https://lore.kernel.org/r/20201127132155.77418-2-geert@linux-m68k.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Fri, 27 Nov 2020 17:00:07 +0000 (18:00 +0100)]
Merge tag 'stm32-dt-for-v5.11-1' of git://git./linux/kernel/git/atorgue/stm32 into arm/dt
STM32 DT updates for v5.11, round 1
Highlights:
----------
MCU part:
-Fix dmamux reg property (length) on stm32h743.
-Explicitly set DCMI bus type on stm32429i eval board.
MPU part:
-Enable FIFO mode with half-full threshold for DCMI.
-Harmonize EHCI/OHCI nodes.
-Move SDMMC IP version to v2.0 to get features improvements.
-Add LP-timer wakeup support.
-Enable crypto/hash/crc support.
-Explicitly set DCMI bus type on stm32mp157 eval board.
-Add USB type-c controller (STUSB1600) on stm32mp15 DK boards
(It is connected to I2C4).
-Fix dmamux reg property (length) on stm32mp151.
-Optimize USB OTG FIFO sizes on stm32mp151.
-Declare tamp node also as "simple-mfd".
-LXA:
-Document Octavo vendor-prefixes yaml file.
-Document lxa,stm32mp157c-mc1 in STM32 yaml file.
-DH:
-Connect PHY IRQ line on DH SoM.
-Add KS8851 Ethernet support on DHCOM which is mapped to FMC2.
-Document all DH compatible strings in STM32 yaml file.
-Add DHCOM based PicoITX board. This board embedds ethernet port,
USB, CAN LEDS and a custom board-to-board connector.
* tag 'stm32-dt-for-v5.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32: (34 commits)
ARM: dts: stm32: lxa-mc1: add OSD32MP15x to list of compatibles
dt-bindings: arm: stm32: add extra SiP compatible for lxa,stm32mp157c-mc1
dt-bindings: vendor-prefixes: document Octavo Systems oct prefix
ARM: dts: stm32: Add DHCOM based PicoITX board
dt-bindings: arm: stm32: Add compatible strings for DH SoMs and boards
ARM: dts: stm32: support child mfd cells for the stm32mp1 TAMP syscon
dt-bindings: arm: stm32: add simple-mfd compatible for tamp node
ARM: dts: stm32: update stm32mp151 for remote proc synchronization support
ARM: dts: stm32: adjust USB OTG gadget fifo sizes in stm32mp151
ARM: dts: stm32: fix dmamux reg property on stm32h743
ARM: dts: stm32: fix dmamux reg property on stm32mp151
ARM: dts: stm32: fix mdma1 clients channel priority level on stm32mp151
ARM: dts: stm32: add STUSB1600 Type-C using I2C4 on stm32mp15xx-dkx
dt-bindings: usb: Add DT bindings for STUSB160x Type-C controller
dt-bindings: connector: add typec-power-opmode property to usb-connector
ARM: dts: stm32: reorder spi4 within stm32mp15-pinctrl
ARM: dts: stm32: set bus-type in DCMI endpoint for stm32429i-eval board
ARM: dts: stm32: set bus-type in DCMI endpoint for stm32mp157c-ev1 board
ARM: dts: stm32: enable CRYP by default on stm32mp15
ARM: dts: stm32: enable CRC1 by default on stm32mp15
...
Link: https://lore.kernel.org/r/873c17a5-28d5-9261-f691-1b917611c932@foss.st.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Fri, 27 Nov 2020 16:58:27 +0000 (17:58 +0100)]
Merge tag 'omap-for-v5.11/dt-signed' of git://git./linux/kernel/git/tmlind/linux-omap into arm/dt
Devicetree changes for omaps for v5.11 merge window
- Two non-urgent pandaboard updates to get gpio button and bluetooth
working on pandaboard-es
- Updates to follow devicetree binding docs for dwc3 and pwm-leds
- Add initial support for droid bionic based on what we have for droid4
- Add second sha instance for dra7
- Add eQEP nodes for am335x for boneblue
- Fix wrong comments for am335x gpio_31
* tag 'omap-for-v5.11/dt-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: am335x: Fix comments for AM335X_PIN_GPMC_WPN pin in GPIO mode
ARM: dts: am335x-boneblue: Enable eQEP
ARM: dts: am33xx: Add nodes for eQEP
ARM: dts: dra7: add second SHA instance
ARM: dts: xt875: add section for kionix kxtf9
ARM: dts: mapphone: separate out xt894 specific things
ARM: dts: omap: Fix schema warnings for pwm-leds
ARM: dts: omap5: Harmonize DWC USB3 DT nodes name
ARM: dts: am437x: Correct DWC USB3 compatible string
ARM: dts: pandaboard es: add bluetooth uart for HCI
ARM: dts: pandaboard: fix pinmux for gpio user button of Pandaboard ES
Link: https://lore.kernel.org/r/pull-1606462656-588116@atomide.com-2
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Frank Wunderlich [Fri, 16 Oct 2020 20:40:18 +0000 (22:40 +0200)]
dts64: mt7622: disable spi1 and uart2 because pins are used by pwm
MDI_TP_P0 (gpio51) is used by pwm1 and uart2 (uart1 on gpio-header)
MDI_RP_P4 (gpio67) is used by pwm4 and spi1
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Link: https://lore.kernel.org/r/20201016204019.2606-3-linux@fw-web.de
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Frank Wunderlich [Fri, 16 Oct 2020 20:40:17 +0000 (22:40 +0200)]
dts64: mt7622: enable all pwm for bananapi r64
mt7622 only supports 6 pwm-channels so drop pwm7
third pwm (pwm2) is inverted and connected to fan-socket
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Link: https://lore.kernel.org/r/20201016204019.2606-2-linux@fw-web.de
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Peter Ujfalusi [Fri, 20 Nov 2020 07:35:33 +0000 (09:35 +0200)]
arm64: dts: ti: k3-j7200-common-proc-board: Correct the name of io expander on main_i2c1
J7200 main_i2c1 is connected to the i2c bus on the CPB marked as main_i2c3
The i2c1 devices on the CPB are _not_ connected to the SoC, they are not
usable with the J7200 SOM.
Correct the expander name from exp4 to exp3 and at the same time add the
line names as well.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Link: https://lore.kernel.org/r/20201120073533.24486-3-peter.ujfalusi@ti.com
Peter Ujfalusi [Fri, 20 Nov 2020 07:35:32 +0000 (09:35 +0200)]
arm64: dts: ti: k3-j7200-som-p0: main_i2c0 have an ioexpander on the SOM
The J7200 SOM have additional io expander which is used to control several
SOM level muxes to make sure that the correct signals are routed to the
correct pin on the SOM <-> CPB connectors.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Link: https://lore.kernel.org/r/20201120073533.24486-2-peter.ujfalusi@ti.com
Enric Balletbo i Serra [Fri, 27 Nov 2020 10:49:30 +0000 (11:49 +0100)]
arm64: dts: mt8183: Add display nodes for MT8183
Add display subsystem device nodes to allow video output.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Link: https://lore.kernel.org/r/20201127104930.1981497-4-enric.balletbo@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Enric Balletbo i Serra [Fri, 27 Nov 2020 10:49:29 +0000 (11:49 +0100)]
arm64: dts: mt8183: Add iommu and larb nodes
Add iommu and larb nodes to the MT8183.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Link: https://lore.kernel.org/r/20201127104930.1981497-3-enric.balletbo@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Jitao Shi [Fri, 27 Nov 2020 10:49:28 +0000 (11:49 +0100)]
arm64: dts: mt8183: Add dsi node
Add dsi and mipitx nodes to the MT8183.
Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Link: https://lore.kernel.org/r/20201127104930.1981497-2-enric.balletbo@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Hsin-Yi Wang [Tue, 24 Nov 2020 04:12:54 +0000 (12:12 +0800)]
arm64: dts: mt8183: Add pwm and backlight node
Add pwm to mt8183 and backlight to mt8183-kukui.
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Tested-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Link: https://lore.kernel.org/r/20201124041253.4181273-1-hsinyi@chromium.org
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Matthias Brugger [Fri, 30 Oct 2020 11:36:19 +0000 (12:36 +0100)]
arm64: dts: mediatek: Add mt8183 power domains controller
Add power domains controller node for SoC mt8183
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Link: https://lore.kernel.org/r/20201030113622.201188-14-enric.balletbo@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Enric Balletbo i Serra [Fri, 30 Oct 2020 11:36:18 +0000 (12:36 +0100)]
arm64: dts: mediatek: Add smi_common node for MT8183
The SMI (Smart Multimedia Interface) Common is a bridge between the m4u
(Multimedia Memory Management Unit) and the Multimedia HW. This block is
needed to support different multimedia features, like display, video
decode, and camera. Also is needed to control the power domains of such
HW blocks.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Link: https://lore.kernel.org/r/20201030113622.201188-13-enric.balletbo@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Enric Balletbo i Serra [Fri, 30 Oct 2020 11:36:09 +0000 (12:36 +0100)]
arm64: dts: mediatek: Add mt8173 power domain controller
Add power domain controller node for SoC mt8173.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Link: https://lore.kernel.org/r/20201030113622.201188-4-enric.balletbo@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Matthias Brugger [Fri, 27 Nov 2020 11:01:31 +0000 (12:01 +0100)]
Merge tag 'v5.10-next-pm-domains-stable' into HEAD
Weiyi Lu [Fri, 30 Oct 2020 11:36:20 +0000 (12:36 +0100)]
dt-bindings: power: Add MT8192 power domains
Add power domains dt-bindings for MT8192.
Signed-off-by: Weiyi Lu <weiyi.lu@mediatek.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20201030113622.201188-15-enric.balletbo@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Enric Balletbo i Serra [Fri, 30 Oct 2020 11:36:16 +0000 (12:36 +0100)]
dt-bindings: power: Add MT8183 power domains
Add power domains dt-bindings for MT8183.
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20201030113622.201188-11-enric.balletbo@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Enric Balletbo i Serra [Fri, 30 Oct 2020 11:36:07 +0000 (12:36 +0100)]
dt-bindings: power: Add bindings for the Mediatek SCPSYS power domains controller
The System Control Processor System (SCPSYS) has several power management
related tasks in the system. Add the bindings to define the power
domains for the SCPSYS power controller.
Co-developed-by: Matthias Brugger <mbrugger@suse.com>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20201030113622.201188-2-enric.balletbo@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Seiya Wang [Fri, 30 Oct 2020 09:22:07 +0000 (17:22 +0800)]
arm64: dts: Add Mediatek SoC MT8192 and evaluation board dts and Makefile
Add basic chip support for Mediatek MT8192
Signed-off-by: Seiya Wang <seiya.wang@mediatek.com>
Link: https://lore.kernel.org/r/20201030092207.26488-2-seiya.wang@mediatek.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Fabien Parent [Tue, 27 Oct 2020 19:48:15 +0000 (20:48 +0100)]
arm64: dts: mediatek: add MT8167 pumpkin board dts
The pumpkin board is made by Gossamer Engineering and is using
a MediaTek SoC. The board currently comes in two available version:
MT8516 SoC and MT8167 SoC.
The board provides the following IOs: eMMC, NAND, SD card, USB type-A,
Ethernet, Wi-Fi, Bluetooth, Audio (jack out, 2 PDM port, 1 analog in),
serial over USB, HDMI, DSI, CSI, and an expansion header.
The board can be powered by battery and/or via a USB Type-C port and
is using a PMIC MT6392.
The eMMC and NAND are sharing pins and cannot be used together.
This commit is adding the basic boot support for the Pumpkin MT8167
board.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Link: https://lore.kernel.org/r/20201027194816.1227654-3-fparent@baylibre.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Fabien Parent [Tue, 27 Oct 2020 19:48:14 +0000 (20:48 +0100)]
arm64: dts: mediatek: add dtsi for MT8167
The MT8167 SoC provides the following peripherals: GPIO, UART, USB2,
SPI, eMMC, SDIO, NAND, Flash, ADC, I2C, PWM, TImers, IR, Ethernet,
Audio (I2S, SPDIF, TDM, HDMI), HDMI, DSI, CSI, MDP (Multimedia Data
Path), Video encoding (H.264), Video Decoding (H.264, VP8).
The MT8167 is compatible with MT8516 but provides multimedia IPs to it.
This commit is just adding the basic dtsi file with the support of the
following IOs: GPIO, Clocks.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Link: https://lore.kernel.org/r/20201027194816.1227654-2-fparent@baylibre.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Fabien Parent [Tue, 27 Oct 2020 19:48:13 +0000 (20:48 +0100)]
dt-bindings: arm64: dts: mediatek: Add mt8167-pumpkin board
Add binding documentation for the MT8167 Pumpkin board.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20201027194816.1227654-1-fparent@baylibre.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Fabien Parent [Fri, 16 Oct 2020 17:18:37 +0000 (19:18 +0200)]
arm64: dts: mediatek: mt8516: add efuse node
Add node to support e-fuses on MT8516
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Link: https://lore.kernel.org/r/20201016171837.3261310-2-fparent@baylibre.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Yuya Hamamachi [Wed, 25 Nov 2020 07:33:03 +0000 (16:33 +0900)]
arm64: dts: renesas: r8a77951: Add PCIe EP nodes
Add PCIe EP nodes for R8A77951 SoC dtsi.
Signed-off-by: Yuya Hamamachi <yuya.hamamachi.sx@renesas.com>
Link: https://lore.kernel.org/r/20201125073303.19057-3-yuya.hamamachi.sx@renesas.com
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Arnd Bergmann [Thu, 26 Nov 2020 21:11:52 +0000 (22:11 +0100)]
Merge tag 'hisi-arm64-dt-for-5.11' of git://github.com/hisilicon/linux-hisi into arm/dt
ARM64: DT: Hisilicon ARM64 DT updates for 5.11
- Cleanups of the hisilicon DTS to align with the dtschema. All of them do not
have any functional effect except passing dtschema checks or dtc W=2 builds.
* tag 'hisi-arm64-dt-for-5.11' of git://github.com/hisilicon/linux-hisi:
arm64: dts: hisilicon: Use generic "ngpios" rather than "snps,nr-gpios"
arm64: dts: hi3660: Harmonize DWC USB3 DT nodes name
arm64: dts: hisilicon: list all clocks required by snps-dw-apb-uart.yaml
arm64: dts: hisilicon: list all clocks required by pl011.yaml
arm64: dts: hisilicon: list all clocks required by spi-pl022.yaml
arm64: dts: hisilicon: normalize the node name of the UART devices
arm64: dts: hisilicon: normalize the node name of the usb devices
arm64: dts: hisilicon: normalize the node name of the SMMU devices
arm64: dts: hisilicon: place clock-names "biu" before "ciu"
arm64: dts: hisilicon: remove unused property pinctrl-names
arm64: dts: hisilicon: write the values of property-units into a uint32 array
arm64: dts: hisilicon: separate each group of data in the property "reg"
arm64: dts: hisilicon: normalize the node name of the ITS devices
Link: https://lore.kernel.org/r/5FBDC416.5060008@hisilicon.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Thu, 26 Nov 2020 21:09:35 +0000 (22:09 +0100)]
Merge tag 'hisi-arm32-dt-for-5.11' of git://github.com/hisilicon/linux-hisi into arm/dt
ARM: DT: Hisilicon ARM32 DT updates for 5.11
- Cleanups of the hisilicon DTS to align with the dtschema including
serial, usb, amba-bus, memory, mmc, spi and syscon. All of them do not
have any functional effect except passing dtschema checks or dtc W=2
builds.
* tag 'hisi-arm32-dt-for-5.11' of git://github.com/hisilicon/linux-hisi:
ARM: dts: hisilicon: fix errors detected by syscon.yaml
ARM: dts: hisilicon: fix errors detected by spi-pl022.yaml
ARM: dts: hisilicon: fix errors detected by synopsys-dw-mshc.yaml
ARM: dts: hisilicon: fix errors detected by root-node.yaml
ARM: dts: hisilicon: fix errors detected by simple-bus.yaml
ARM: dts: hisilicon: fix errors detected by usb yaml
ARM: dts: hisilicon: fix errors detected by pl011.yaml
ARM: dts: hisilicon: fix errors detected by snps-dw-apb-uart.yaml
Link: https://lore.kernel.org/r/5FBDC347.4050102@hisilicon.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Dmitry Osipenko [Mon, 23 Nov 2020 00:27:23 +0000 (03:27 +0300)]
ARM: tegra: Add EMC OPP and ICC properties to Tegra124 EMC and ACTMON device-tree nodes
Add EMC OPP DVFS/DFS tables and interconnect paths that will be used for
dynamic memory bandwidth scaling based on memory utilization statistics.
Update board device-trees by removing unsupported EMC OPPs.
Note that ACTMON watches all memory interconnect paths, but we use a
single CPU-READ interconnect path for driving memory bandwidth, for
simplicity.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Dmitry Osipenko [Mon, 23 Nov 2020 00:27:22 +0000 (03:27 +0300)]
ARM: tegra: Add EMC OPP and ICC properties to Tegra30 EMC and ACTMON device-tree nodes
Add EMC OPP tables and interconnect paths that will be used for
dynamic memory bandwidth scaling based on memory utilization statistics.
Update board device-trees by removing unsupported EMC OPPs.
Note that ACTMON watches all memory interconnect paths, but we use a
single CPU-READ interconnect path for driving memory bandwidth, for
simplicity.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Dmitry Osipenko [Mon, 23 Nov 2020 00:27:21 +0000 (03:27 +0300)]
ARM: tegra: Add EMC OPP properties to Tegra20 device-trees
Add EMC OPP DVFS tables and update board device-trees by removing
unsupported OPPs.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Dmitry Osipenko [Mon, 23 Nov 2020 00:27:20 +0000 (03:27 +0300)]
ARM: tegra: Add nvidia,memory-controller phandle to Tegra20 EMC device-tree
Add nvidia,memory-controller to the Tegra20 External Memory Controller
node. This allows to perform a direct lookup of the Memory Controller
instead of walking up the whole tree. This puts Tegra20 device-tree on
par with Tegra30+.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Dmitry Osipenko [Mon, 23 Nov 2020 00:27:19 +0000 (03:27 +0300)]
ARM: tegra: Add interconnect properties to Tegra124 device-tree
Add interconnect properties to the Memory Controller, External Memory
Controller and the Display Controller nodes in order to describe hardware
interconnection.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Dmitry Osipenko [Mon, 23 Nov 2020 00:27:18 +0000 (03:27 +0300)]
ARM: tegra: Add interconnect properties to Tegra30 device-tree
Add interconnect properties to the Memory Controller, External Memory
Controller and the Display Controller nodes in order to describe hardware
interconnection.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Dmitry Osipenko [Mon, 23 Nov 2020 00:27:17 +0000 (03:27 +0300)]
ARM: tegra: Add interconnect properties to Tegra20 device-tree
Add interconnect properties to the Memory Controller, External Memory
Controller and the Display Controller nodes in order to describe hardware
interconnection.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Dmitry Osipenko [Mon, 16 Nov 2020 19:48:27 +0000 (22:48 +0300)]
ARM: tegra: acer-a500: Add Embedded Controller
This patch adds device-tree node for the Embedded Controller which is
found on the Picasso board. The Embedded Controller itself is ENE KB930,
it provides functions like battery-gauge/LED/GPIO/etc and it uses firmware
that is specifically customized for the Acer A500 device.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Sowjanya Komatineni [Mon, 23 Nov 2020 20:17:20 +0000 (12:17 -0800)]
ARM: tegra: Change order of SATA resets for Tegra124
Tegra AHCI dt-binding doc is converted from text based to yaml based.
dtbs_check valdiation strictly follows reset-names order specified
in yaml dt-binding.
Tegra124 thru Tegra210 has 3 resets sata, sata-oob and sata-cold.
Tegra186 has 2 resets sata and sata-cold.
This patch changes order of SATA resets to maintain proper resets
order for commonly available resets across Tegra124 thru Tegra186
for dtbs_check to pass.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Dmitry Osipenko [Mon, 23 Nov 2020 00:27:16 +0000 (03:27 +0300)]
ARM: tegra: Correct EMC registers size in Tegra20 device-tree
Fix the size of Tegra20 EMC registers, which should be twice bigger.
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Thierry Reding [Fri, 20 Nov 2020 20:27:12 +0000 (21:27 +0100)]
ARM: tegra: Properly align clocks for SOCTHERM
Entries on subsequent lines should be aligned with the entry on the
first line.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Thierry Reding [Fri, 20 Nov 2020 15:18:08 +0000 (16:18 +0100)]
ARM: tegra: Hook up edp interrupt on Tegra124 SOCTHERM
For some reason this was never hooked up. Do it now so that over-current
interrupts can be logged.
Reported-by: Nicolas Chauvet <kwizart@gmail.com>
Suggested-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
projects / platform / kernel / linux-starfive.git / log