Chin-Yen Lee [Wed, 28 Jul 2021 01:43:31 +0000 (09:43 +0800)]
rtw88: use read_poll_timeout instead of fixed sleep
[ Upstream commit
02a55c0009a55b204e1e5c17295431f0a9e7d3b6 ]
In current wow flow, driver calls rtw_wow_fw_start and sleep for 100ms,
to wait firmware finish preliminary work and then update the value of
WOWLAN_WAKE_REASON register to zero. But later firmware will start wow
function with power-saving mode, in which mode the value of
WOWLAN_WAKE_REASON register is 0xea. So driver may get 0xea value and
return fail. We use read_poll_timeout instead to check the value to avoid
this issue.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210728014335.8785-2-pkshih@realtek.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
Chris Chiu [Wed, 4 Aug 2021 15:13:25 +0000 (23:13 +0800)]
rtl8xxxu: Fix the handling of TX A-MPDU aggregation
[ Upstream commit
95a581ab3592082c60a08090aabe09ac7d0bd650 ]
The TX A-MPDU aggregation is not handled in the driver since the
ieee80211_start_tx_ba_session has never been started properly.
Start and stop the TX BA session by tracking the TX aggregation
status of each TID. Fix the ampdu_action and the tx descriptor
accordingly with the given TID.
Signed-off-by: Chris Chiu <chris.chiu@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210804151325.86600-1-chris.chiu@canonical.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
Nathan Chancellor [Tue, 27 Jul 2021 23:36:56 +0000 (16:36 -0700)]
drm/exynos: Always initialize mapping in exynos_drm_register_dma()
[ Upstream commit
c626f3864bbbb28bbe06476b0b497c1330aa4463 ]
In certain randconfigs, clang warns:
drivers/gpu/drm/exynos/exynos_drm_dma.c:121:19: warning: variable
'mapping' is uninitialized when used here [-Wuninitialized]
priv->mapping = mapping;
^~~~~~~
drivers/gpu/drm/exynos/exynos_drm_dma.c:111:16: note: initialize the
variable 'mapping' to silence this warning
void *mapping;
^
= NULL
1 warning generated.
This occurs when CONFIG_EXYNOS_IOMMU is enabled and both
CONFIG_ARM_DMA_USE_IOMMU and CONFIG_IOMMU_DMA are disabled, which makes
the code look like
void *mapping;
if (0)
mapping = arm_iommu_create_mapping()
else if (0)
mapping = iommu_get_domain_for_dev()
...
priv->mapping = mapping;
Add an else branch that initializes mapping to the -ENODEV error pointer
so that there is no more warning and the driver does not change during
runtime.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
J. Bruce Fields [Fri, 20 Aug 2021 21:01:59 +0000 (17:01 -0400)]
lockd: lockd server-side shouldn't set fl_ops
[ Upstream commit
7de875b231edb807387a81cde288aa9e1015ef9e ]
Locks have two sets of op arrays, fl_lmops for the lock manager (lockd
or nfsd), fl_ops for the filesystem. The server-side lockd code has
been setting its own fl_ops, which leads to confusion (and crashes) in
the reexport case, where the filesystem expects to be the only one
setting fl_ops.
And there's no reason for it that I can see-the lm_get/put_owner ops do
the same job.
Reported-by: Daire Byrne <daire@dneg.com>
Tested-by: Daire Byrne <daire@dneg.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Li Jun [Fri, 18 Jun 2021 08:28:58 +0000 (16:28 +0800)]
usb: chipidea: host: fix port index underflow and UBSAN complains
[ Upstream commit
e5d6a7c6cfae9e714a0e8ff64facd1ac68a784c6 ]
If wIndex is 0 (and it often is), these calculations underflow and
UBSAN complains, here resolve this by not decrementing the index when
it is equal to 0, this copies the solution from commit
85e3990bea49
("USB: EHCI: avoid undefined pointer arithmetic and placate UBSAN")
Reported-by: Zhipeng Wang <zhipeng.wang_1@nxp.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
Link: https://lore.kernel.org/r/1624004938-2399-1-git-send-email-jun.li@nxp.com
Signed-off-by: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Bob Peterson [Fri, 30 Jul 2021 17:41:49 +0000 (12:41 -0500)]
gfs2: Don't call dlm after protocol is unmounted
[ Upstream commit
d1340f80f0b8066321b499a376780da00560e857 ]
In the gfs2 withdraw sequence, the dlm protocol is unmounted with a call
to lm_unmount. After a withdraw, users are allowed to unmount the
withdrawn file system. But at that point we may still have glocks left
over that we need to free via unmount's call to gfs2_gl_hash_clear.
These glocks may have never been completed because of whatever problem
caused the withdraw (IO errors or whatever).
Before this patch, function gdlm_put_lock would still try to call into
dlm to unlock these leftover glocks, which resulted in dlm returning
-EINVAL because the lock space was abandoned. These glocks were never
freed because there was no mechanism after that to free them.
This patch adds a check to gdlm_put_lock to see if the locking protocol
was inactive (DFL_UNMOUNT flag) and if so, free the glock and not
make the invalid call into dlm.
I could have combined this "if" with the one that follows, related to
leftover glock LVBs, but I felt the code was more readable with its own
if clause.
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Mark Brown [Thu, 19 Aug 2021 16:57:23 +0000 (17:57 +0100)]
kselftest/arm64: pac: Fix skipping of tests on systems without PAC
[ Upstream commit
0c69bd2ca6ee20064dde7853cd749284e053a874 ]
The PAC tests check to see if the system supports the relevant PAC features
but instead of skipping the tests if they can't be executed they fail the
tests which makes things look like they're not working when they are.
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20210819165723.43903-1-broonie@kernel.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Mark Brown [Thu, 19 Aug 2021 17:29:02 +0000 (18:29 +0100)]
kselftest/arm64: mte: Fix misleading output when skipping tests
[ Upstream commit
83e5dcbece4ea67ec3ad94b897e2844184802fd7 ]
When skipping the tests due to a lack of system support for MTE we
currently print a message saying FAIL which makes it look like the test
failed even though the test did actually report KSFT_SKIP, creating some
confusion. Change the error message to say SKIP instead so things are
clearer.
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20210819172902.56211-1-broonie@kernel.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Eli Cohen [Tue, 17 Aug 2021 17:05:18 +0000 (20:05 +0300)]
net: Fix offloading indirect devices dependency on qdisc order creation
[ Upstream commit
74fc4f828769cca1c3be89ea92cb88feaa27ef52 ]
Currently, when creating an ingress qdisc on an indirect device before
the driver registered for callbacks, the driver will not have a chance
to register its filter configuration callbacks.
To fix that, modify the code such that it keeps track of all the ingress
qdiscs that call flow_indr_dev_setup_offload(). When a driver calls
flow_indr_dev_register(), go through the list of tracked ingress qdiscs
and call the driver callback entry point so as to give it a chance to
register its callback.
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Eli Cohen <elic@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Kees Cook [Wed, 18 Aug 2021 04:42:52 +0000 (21:42 -0700)]
staging: rts5208: Fix get_ms_information() heap buffer size
[ Upstream commit
cbe34165cc1b7d1110b268ba8b9f30843c941639 ]
Fix buf allocation size (it needs to be 2 bytes larger). Found when
__alloc_size() annotations were added to kmalloc() interfaces.
In file included from ./include/linux/string.h:253,
from ./include/linux/bitmap.h:10,
from ./include/linux/cpumask.h:12,
from ./arch/x86/include/asm/paravirt.h:17,
from ./arch/x86/include/asm/irqflags.h:63,
from ./include/linux/irqflags.h:16,
from ./include/linux/rcupdate.h:26,
from ./include/linux/rculist.h:11,
from ./include/linux/pid.h:5,
from ./include/linux/sched.h:14,
from ./include/linux/blkdev.h:5,
from drivers/staging/rts5208/rtsx_scsi.c:12:
In function 'get_ms_information',
inlined from 'ms_sp_cmnd' at drivers/staging/rts5208/rtsx_scsi.c:2877:12,
inlined from 'rtsx_scsi_handler' at drivers/staging/rts5208/rtsx_scsi.c:3247:12:
./include/linux/fortify-string.h:54:29: warning: '__builtin_memcpy' forming offset [106, 107] is out
of the bounds [0, 106] [-Warray-bounds]
54 | #define __underlying_memcpy __builtin_memcpy
| ^
./include/linux/fortify-string.h:417:2: note: in expansion of macro '__underlying_memcpy'
417 | __underlying_##op(p, q, __fortify_size); \
| ^~~~~~~~~~~~~
./include/linux/fortify-string.h:463:26: note: in expansion of macro '__fortify_memcpy_chk'
463 | #define memcpy(p, q, s) __fortify_memcpy_chk(p, q, s, \
| ^~~~~~~~~~~~~~~~~~~~
drivers/staging/rts5208/rtsx_scsi.c:2851:3: note: in expansion of macro 'memcpy'
2851 | memcpy(buf + i, ms_card->raw_sys_info, 96);
| ^~~~~~
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-staging@lists.linux.dev
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20210818044252.1533634-1-keescook@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Brandon Wyman [Fri, 6 Aug 2021 22:51:31 +0000 (22:51 +0000)]
hwmon: (pmbus/ibm-cffps) Fix write bits for LED control
[ Upstream commit
76b72736f574ec38b3e94603ea5f74b1853f26b0 ]
When doing a PMBus write for the LED control on the IBM Common Form
Factor Power Supplies (ibm-cffps), the DAh command requires that bit 7
be low and bit 6 be high in order to indicate that you are truly
attempting to do a write.
Signed-off-by: Brandon Wyman <bjwyman@gmail.com>
Link: https://lore.kernel.org/r/20210806225131.1808759-1-bjwyman@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Yonghong Song [Tue, 17 Aug 2021 19:09:23 +0000 (12:09 -0700)]
selftests/bpf: Fix flaky send_signal test
[ Upstream commit
b16ac5bf732a5e23d164cf908ec7742d6a6120d3 ]
libbpf CI has reported send_signal test is flaky although
I am not able to reproduce it in my local environment.
But I am able to reproduce with on-demand libbpf CI ([1]).
Through code analysis, the following is possible reason.
The failed subtest runs bpf program in softirq environment.
Since bpf_send_signal() only sends to a fork of "test_progs"
process. If the underlying current task is
not "test_progs", bpf_send_signal() will not be triggered
and the subtest will fail.
To reduce the chances where the underlying process is not
the intended one, this patch boosted scheduling priority to
-20 (highest allowed by setpriority() call). And I did
10 runs with on-demand libbpf CI with this patch and I
didn't observe any failures.
[1] https://github.com/libbpf/libbpf/actions/workflows/ondemand.yml
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20210817190923.3186725-1-yhs@fb.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
J. Bruce Fields [Thu, 12 Aug 2021 20:41:42 +0000 (16:41 -0400)]
rpc: fix gss_svc_init cleanup on failure
[ Upstream commit
5a4753446253a427c0ff1e433b9c4933e5af207c ]
The failure case here should be rare, but it's obviously wrong.
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Luke Hsiao [Mon, 16 Aug 2021 20:51:06 +0000 (20:51 +0000)]
tcp: enable data-less, empty-cookie SYN with TFO_SERVER_COOKIE_NOT_REQD
[ Upstream commit
e3faa49bcecdfcc80e94dd75709d6acb1a5d89f6 ]
Since the original TFO server code was implemented in commit
168a8f58059a22feb9e9a2dcc1b8053dbbbc12ef ("tcp: TCP Fast Open Server -
main code path") the TFO server code has supported the sysctl bit flag
TFO_SERVER_COOKIE_NOT_REQD. Currently, when the TFO_SERVER_ENABLE and
TFO_SERVER_COOKIE_NOT_REQD sysctl bit flags are set, a server connection
will accept a SYN with N bytes of data (N > 0) that has no TFO cookie,
create a new fast open connection, process the incoming data in the SYN,
and make the connection ready for accepting. After accepting, the
connection is ready for read()/recvmsg() to read the N bytes of data in
the SYN, ready for write()/sendmsg() calls and data transmissions to
transmit data.
This commit changes an edge case in this feature by changing this
behavior to apply to (N >= 0) bytes of data in the SYN rather than only
(N > 0) bytes of data in the SYN. Now, a server will accept a data-less
SYN without a TFO cookie if TFO_SERVER_COOKIE_NOT_REQD is set.
Caveat! While this enables a new kind of TFO (data-less empty-cookie
SYN), some firewall rules setup may not work if they assume such packets
are not legit TFOs and will filter them.
Signed-off-by: Luke Hsiao <lukehsiao@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20210816205105.2533289-1-luke.w.hsiao@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Darrick J. Wong [Wed, 11 Aug 2021 01:32:55 +0000 (18:32 -0700)]
iomap: pass writeback errors to the mapping
[ Upstream commit
b69eea82d37d9ee7cfb3bf05103549dd4ed5ffc3 ]
Modern-day mapping_set_error has the ability to squash the usual
negative error code into something appropriate for long-term storage in
a struct address_space -- ENOSPC becomes AS_ENOSPC, and everything else
becomes EIO. iomap squashes /everything/ to EIO, just as XFS did before
that, but this doesn't make sense.
Fix this by making it so that we can pass ENOSPC to userspace when
writeback fails due to space problems.
Signed-off-by: Darrick J. Wong <djwong@kernel.org>
Reviewed-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Ulrich Hecht [Mon, 16 Aug 2021 16:22:01 +0000 (18:22 +0200)]
serial: sh-sci: fix break handling for sysrq
[ Upstream commit
87b8061bad9bd4b549b2daf36ffbaa57be2789a2 ]
This fixes two issues that cause the sysrq sequence to be inadvertently
aborted on SCIF serial consoles:
- a NUL character remains in the RX queue after a break has been detected,
which is then passed on to uart_handle_sysrq_char()
- the break interrupt is handled twice on controllers with multiplexed ERI
and BRI interrupts
Signed-off-by: Ulrich Hecht <uli+renesas@fpond.eu>
Link: https://lore.kernel.org/r/20210816162201.28801-1-uli+renesas@fpond.eu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Rajendra Nayak [Thu, 12 Aug 2021 11:27:20 +0000 (16:57 +0530)]
opp: Don't print an error if required-opps is missing
[ Upstream commit
020d86fc0df8b865f6dc168d88a7c2dccabd0a9e ]
The 'required-opps' property is considered optional, hence remove
the pr_err() in of_parse_required_opp() when we find the property is
missing.
While at it, also fix the return value of
of_get_required_opp_performance_state() when of_parse_required_opp()
fails, return a -ENODEV instead of the -EINVAL.
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Luiz Augusto von Dentz [Wed, 11 Aug 2021 23:20:15 +0000 (16:20 -0700)]
Bluetooth: Fix handling of LE Enhanced Connection Complete
[ Upstream commit
cafae4cd625502f65d1798659c1aa9b62d38cc56 ]
LE Enhanced Connection Complete contains the Local RPA used in the
connection which must be used when set otherwise there could problems
when pairing since the address used by the remote stack could be the
Local RPA:
BLUETOOTH CORE SPECIFICATION Version 5.2 | Vol 4, Part E
page 2396
'Resolvable Private Address being used by the local device for this
connection. This is only valid when the Own_Address_Type (from the
HCI_LE_Create_Connection, HCI_LE_Set_Advertising_Parameters,
HCI_LE_Set_Extended_Advertising_Parameters, or
HCI_LE_Extended_Create_Connection commands) is set to 0x02 or
0x03, and the Controller generated a resolvable private address for the
local device using a non-zero local IRK. For other Own_Address_Type
values, the Controller shall return all zeros.'
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Sagi Grimberg [Wed, 16 Jun 2021 21:19:36 +0000 (14:19 -0700)]
nvme: code command_id with a genctr for use-after-free validation
[ Upstream commit
e7006de6c23803799be000a5dcce4d916a36541a ]
We cannot detect a (perhaps buggy) controller that is sending us
a completion for a request that was already completed (for example
sending a completion twice), this phenomenon was seen in the wild
a few times.
So to protect against this, we use the upper 4 msbits of the nvme sqe
command_id to use as a 4-bit generation counter and verify it matches
the existing request generation that is incrementing on every execution.
The 16-bit command_id structure now is constructed by:
| xxxx | xxxxxxxxxxxx |
gen request tag
This means that we are giving up some possible queue depth as 12 bits
allow for a maximum queue depth of 4095 instead of 65536, however we
never create such long queues anyways so no real harm done.
Suggested-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Acked-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Daniel Wagner <dwagner@suse.de>
Tested-by: Daniel Wagner <dwagner@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Sagi Grimberg [Wed, 16 Jun 2021 21:19:35 +0000 (14:19 -0700)]
nvme-tcp: don't check blk_mq_tag_to_rq when receiving pdu data
[ Upstream commit
3b01a9d0caa8276d9ce314e09610f7fb70f49a00 ]
We already validate it when receiving the c2hdata pdu header
and this is not changing so this is a redundant check.
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Daniel Wagner <dwagner@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Raag Jadav [Wed, 4 Aug 2021 19:24:45 +0000 (00:54 +0530)]
arm64: dts: ls1046a: fix eeprom entries
[ Upstream commit
c1a6018d1839c9cb8f807dc863a50102a1a5c412 ]
ls1046afrwy and ls1046ardb boards have CAT24C04[1] and CAT24C05[2]
eeproms respectively. Both are 4Kb (512 bytes) in size,
and compatible with AT24C04[3].
Remove multi-address entries, as both the boards have a single chip each.
[1] https://www.onsemi.com/pdf/datasheet/cat24c01-d.pdf
[2] https://www.onsemi.com/pdf/datasheet/cat24c03-d.pdf
[3] https://ww1.microchip.com/downloads/en/DeviceDoc/doc0180.pdf
Signed-off-by: Raag Jadav <raagjadav@gmail.com>
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Thierry Reding [Tue, 22 Jun 2021 13:44:22 +0000 (15:44 +0200)]
arm64: tegra: Fix compatible string for Tegra132 CPUs
[ Upstream commit
f865d0292ff3c0ca09414436510eb4c815815509 ]
The documented compatible string for the CPUs found on Tegra132 is
"nvidia,tegra132-denver", rather than the previously used compatible
string "nvidia,denver".
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Andreas Obergschwandtner [Thu, 29 Jul 2021 14:42:26 +0000 (16:42 +0200)]
ARM: tegra: tamonten: Fix UART pad setting
[ Upstream commit
2270ad2f4e123336af685ecedd1618701cb4ca1e ]
This patch fixes the tristate and pullup configuration for UART 1 to 3
on the Tamonten SOM.
Signed-off-by: Andreas Obergschwandtner <andreas.obergschwandtner@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Dmitry Osipenko [Mon, 2 Aug 2021 21:19:43 +0000 (00:19 +0300)]
ARM: tegra: acer-a500: Remove bogus USB VBUS regulators
[ Upstream commit
70e740ad55e5f93a19493720f4105555fade4a73 ]
The configuration of USB VBUS regulators was borrowed from downstream
kernel, which is incorrect because the corresponding GPIOs are connected
to PROX_EN (A501 3G model) and LED_EN pins in accordance to the board
schematics. USB works fine with both GPIOs being disabled, so remove the
bogus USB VBUS regulators. The USB VBUS of USB3 is supplied from the fixed
5v system regulator and device-mode USB1 doesn't have VBUS switches.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Johan Almbladh [Mon, 28 Jun 2021 12:32:46 +0000 (14:32 +0200)]
mac80211: Fix monitor MTU limit so that A-MSDUs get through
[ Upstream commit
79f5962baea74ce1cd4e5949598944bff854b166 ]
The maximum MTU was set to 2304, which is the maximum MSDU size. While
this is valid for normal WLAN interfaces, it is too low for monitor
interfaces. A monitor interface may receive and inject MPDU frames, and
the maximum MPDU frame size is larger than 2304. The MPDU may also
contain an A-MSDU frame, in which case the size may be much larger than
the MTU limit. Since the maximum size of an A-MSDU depends on the PHY
mode of the transmitting STA, it is not possible to set an exact MTU
limit for a monitor interface. Now the maximum MTU for a monitor
interface is unrestricted.
Signed-off-by: Johan Almbladh <johan.almbladh@anyfinetworks.com>
Link: https://lore.kernel.org/r/20210628123246.2070558-1-johan.almbladh@anyfinetworks.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Tuo Li [Wed, 11 Aug 2021 04:07:03 +0000 (21:07 -0700)]
drm/display: fix possible null-pointer dereference in dcn10_set_clock()
[ Upstream commit
554594567b1fa3da74f88ec7b2dc83d000c58e98 ]
The variable dc->clk_mgr is checked in:
if (dc->clk_mgr && dc->clk_mgr->funcs->get_clock)
This indicates dc->clk_mgr can be NULL.
However, it is dereferenced in:
if (!dc->clk_mgr->funcs->get_clock)
To fix this null-pointer dereference, check dc->clk_mgr and the function
pointer dc->clk_mgr->funcs->get_clock earlier, and return if one of them
is NULL.
Reported-by: TOTE Robot <oslab@tsinghua.edu.cn>
Signed-off-by: Tuo Li <islituo@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Tuo Li [Wed, 11 Aug 2021 11:34:58 +0000 (04:34 -0700)]
gpu: drm: amd: amdgpu: amdgpu_i2c: fix possible uninitialized-variable access in amdgpu_i2c_router_select_ddc_port()
[ Upstream commit
a211260c34cfadc6068fece8c9e99e0fe1e2a2b6 ]
The variable val is declared without initialization, and its address is
passed to amdgpu_i2c_get_byte(). In this function, the value of val is
accessed in:
DRM_DEBUG("i2c 0x%02x 0x%02x read failed\n",
addr, *val);
Also, when amdgpu_i2c_get_byte() returns, val may remain uninitialized,
but it is accessed in:
val &= ~amdgpu_connector->router.ddc_mux_control_pin;
To fix this possible uninitialized-variable access, initialize val to 0 in
amdgpu_i2c_router_select_ddc_port().
Reported-by: TOTE Robot <oslab@tsinghua.edu.cn>
Signed-off-by: Tuo Li <islituo@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Eran Ben Elisha [Tue, 10 Aug 2021 18:15:05 +0000 (21:15 +0300)]
net/mlx5: Fix variable type to match 64bit
[ Upstream commit
979aa51967add26b37f9d77e01729d44a2da8e5f ]
Fix the following smatch warning:
wait_func_handle_exec_timeout() warn: should '1 << ent->idx' be a 64 bit type?
Use 1ULL, to have a 64 bit type variable.
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Eran Ben Elisha <eranbe@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Kuogee Hsieh [Thu, 5 Aug 2021 20:44:54 +0000 (13:44 -0700)]
drm/msm/dp: return correct edid checksum after corrupted edid checksum read
[ Upstream commit
7948fe12d47a946fb8025a0534c900e3dd4b5839 ]
Response with correct edid checksum saved at connector after corrupted edid
checksum read. This fixes Link Layer CTS cases 4.2.2.3, 4.2.2.6.
Signed-off-by: Kuogee Hsieh <khsieh@codeaurora.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/1628196295-7382-6-git-send-email-khsieh@codeaurora.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Desmond Cheong Zhi Xi [Tue, 10 Aug 2021 04:14:06 +0000 (12:14 +0800)]
Bluetooth: avoid circular locks in sco_sock_connect
[ Upstream commit
734bc5ff783115aa3164f4e9dd5967ae78e0a8ab ]
In a future patch, calls to bh_lock_sock in sco.c should be replaced
by lock_sock now that none of the functions are run in IRQ context.
However, doing so results in a circular locking dependency:
======================================================
WARNING: possible circular locking dependency detected
5.14.0-rc4-syzkaller #0 Not tainted
------------------------------------------------------
syz-executor.2/14867 is trying to acquire lock:
ffff88803e3c1120 (sk_lock-AF_BLUETOOTH-BTPROTO_SCO){+.+.}-{0:0}, at:
lock_sock include/net/sock.h:1613 [inline]
ffff88803e3c1120 (sk_lock-AF_BLUETOOTH-BTPROTO_SCO){+.+.}-{0:0}, at:
sco_conn_del+0x12a/0x2a0 net/bluetooth/sco.c:191
but task is already holding lock:
ffffffff8d2dc7c8 (hci_cb_list_lock){+.+.}-{3:3}, at:
hci_disconn_cfm include/net/bluetooth/hci_core.h:1497 [inline]
ffffffff8d2dc7c8 (hci_cb_list_lock){+.+.}-{3:3}, at:
hci_conn_hash_flush+0xda/0x260 net/bluetooth/hci_conn.c:1608
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #2 (hci_cb_list_lock){+.+.}-{3:3}:
__mutex_lock_common kernel/locking/mutex.c:959 [inline]
__mutex_lock+0x12a/0x10a0 kernel/locking/mutex.c:1104
hci_connect_cfm include/net/bluetooth/hci_core.h:1482 [inline]
hci_remote_features_evt net/bluetooth/hci_event.c:3263 [inline]
hci_event_packet+0x2f4d/0x7c50 net/bluetooth/hci_event.c:6240
hci_rx_work+0x4f8/0xd30 net/bluetooth/hci_core.c:5122
process_one_work+0x98d/0x1630 kernel/workqueue.c:2276
worker_thread+0x658/0x11f0 kernel/workqueue.c:2422
kthread+0x3e5/0x4d0 kernel/kthread.c:319
ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:295
-> #1 (&hdev->lock){+.+.}-{3:3}:
__mutex_lock_common kernel/locking/mutex.c:959 [inline]
__mutex_lock+0x12a/0x10a0 kernel/locking/mutex.c:1104
sco_connect net/bluetooth/sco.c:245 [inline]
sco_sock_connect+0x227/0xa10 net/bluetooth/sco.c:601
__sys_connect_file+0x155/0x1a0 net/socket.c:1879
__sys_connect+0x161/0x190 net/socket.c:1896
__do_sys_connect net/socket.c:1906 [inline]
__se_sys_connect net/socket.c:1903 [inline]
__x64_sys_connect+0x6f/0xb0 net/socket.c:1903
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x35/0xb0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x44/0xae
-> #0 (sk_lock-AF_BLUETOOTH-BTPROTO_SCO){+.+.}-{0:0}:
check_prev_add kernel/locking/lockdep.c:3051 [inline]
check_prevs_add kernel/locking/lockdep.c:3174 [inline]
validate_chain kernel/locking/lockdep.c:3789 [inline]
__lock_acquire+0x2a07/0x54a0 kernel/locking/lockdep.c:5015
lock_acquire kernel/locking/lockdep.c:5625 [inline]
lock_acquire+0x1ab/0x510 kernel/locking/lockdep.c:5590
lock_sock_nested+0xca/0x120 net/core/sock.c:3170
lock_sock include/net/sock.h:1613 [inline]
sco_conn_del+0x12a/0x2a0 net/bluetooth/sco.c:191
sco_disconn_cfm+0x71/0xb0 net/bluetooth/sco.c:1202
hci_disconn_cfm include/net/bluetooth/hci_core.h:1500 [inline]
hci_conn_hash_flush+0x127/0x260 net/bluetooth/hci_conn.c:1608
hci_dev_do_close+0x528/0x1130 net/bluetooth/hci_core.c:1778
hci_unregister_dev+0x1c0/0x5a0 net/bluetooth/hci_core.c:4015
vhci_release+0x70/0xe0 drivers/bluetooth/hci_vhci.c:340
__fput+0x288/0x920 fs/file_table.c:280
task_work_run+0xdd/0x1a0 kernel/task_work.c:164
exit_task_work include/linux/task_work.h:32 [inline]
do_exit+0xbd4/0x2a60 kernel/exit.c:825
do_group_exit+0x125/0x310 kernel/exit.c:922
get_signal+0x47f/0x2160 kernel/signal.c:2808
arch_do_signal_or_restart+0x2a9/0x1c40 arch/x86/kernel/signal.c:865
handle_signal_work kernel/entry/common.c:148 [inline]
exit_to_user_mode_loop kernel/entry/common.c:172 [inline]
exit_to_user_mode_prepare+0x17d/0x290 kernel/entry/common.c:209
__syscall_exit_to_user_mode_work kernel/entry/common.c:291 [inline]
syscall_exit_to_user_mode+0x19/0x60 kernel/entry/common.c:302
ret_from_fork+0x15/0x30 arch/x86/entry/entry_64.S:288
other info that might help us debug this:
Chain exists of:
sk_lock-AF_BLUETOOTH-BTPROTO_SCO --> &hdev->lock --> hci_cb_list_lock
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(hci_cb_list_lock);
lock(&hdev->lock);
lock(hci_cb_list_lock);
lock(sk_lock-AF_BLUETOOTH-BTPROTO_SCO);
*** DEADLOCK ***
The issue is that the lock hierarchy should go from &hdev->lock -->
hci_cb_list_lock --> sk_lock-AF_BLUETOOTH-BTPROTO_SCO. For example,
one such call trace is:
hci_dev_do_close():
hci_dev_lock();
hci_conn_hash_flush():
hci_disconn_cfm():
mutex_lock(&hci_cb_list_lock);
sco_disconn_cfm():
sco_conn_del():
lock_sock(sk);
However, in sco_sock_connect, we call lock_sock before calling
hci_dev_lock inside sco_connect, thus inverting the lock hierarchy.
We fix this by pulling the call to hci_dev_lock out from sco_connect.
Signed-off-by: Desmond Cheong Zhi Xi <desmondcheongzx@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Desmond Cheong Zhi Xi [Tue, 10 Aug 2021 04:14:05 +0000 (12:14 +0800)]
Bluetooth: schedule SCO timeouts with delayed_work
[ Upstream commit
ba316be1b6a00db7126ed9a39f9bee434a508043 ]
struct sock.sk_timer should be used as a sock cleanup timer. However,
SCO uses it to implement sock timeouts.
This causes issues because struct sock.sk_timer's callback is run in
an IRQ context, and the timer callback function sco_sock_timeout takes
a spin lock on the socket. However, other functions such as
sco_conn_del and sco_conn_ready take the spin lock with interrupts
enabled.
This inconsistent {SOFTIRQ-ON-W} -> {IN-SOFTIRQ-W} lock usage could
lead to deadlocks as reported by Syzbot [1]:
CPU0
----
lock(slock-AF_BLUETOOTH-BTPROTO_SCO);
<Interrupt>
lock(slock-AF_BLUETOOTH-BTPROTO_SCO);
To fix this, we use delayed work to implement SCO sock timouts
instead. This allows us to avoid taking the spin lock on the socket in
an IRQ context, and corrects the misuse of struct sock.sk_timer.
As a note, cancel_delayed_work is used instead of
cancel_delayed_work_sync in sco_sock_set_timer and
sco_sock_clear_timer to avoid a deadlock. In the future, the call to
bh_lock_sock inside sco_sock_timeout should be changed to lock_sock to
synchronize with other functions using lock_sock. However, since
sco_sock_set_timer and sco_sock_clear_timer are sometimes called under
the locked socket (in sco_connect and __sco_sock_close),
cancel_delayed_work_sync might cause them to sleep until an
sco_sock_timeout that has started finishes running. But
sco_sock_timeout would also sleep until it can grab the lock_sock.
Using cancel_delayed_work is fine because sco_sock_timeout does not
change from run to run, hence there is no functional difference
between:
1. waiting for a timeout to finish running before scheduling another
timeout
2. scheduling another timeout while a timeout is running.
Link: https://syzkaller.appspot.com/bug?id=9089d89de0502e120f234ca0fc8a703f7368b31e
Reported-by: syzbot+2f6d7c28bb4bf7e82060@syzkaller.appspotmail.com
Tested-by: syzbot+2f6d7c28bb4bf7e82060@syzkaller.appspotmail.com
Signed-off-by: Desmond Cheong Zhi Xi <desmondcheongzx@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Desmond Cheong Zhi Xi [Sat, 24 Jul 2021 11:18:24 +0000 (19:18 +0800)]
drm/vmwgfx: fix potential UAF in vmwgfx_surface.c
[ Upstream commit
2bc5da528dd570c5ecabc107e6fbdbc55974276f ]
drm_file.master should be protected by either drm_device.master_mutex
or drm_file.master_lookup_lock when being dereferenced. However,
drm_master_get is called on unprotected file_priv->master pointers in
vmw_surface_define_ioctl and vmw_gb_surface_define_internal.
This is fixed by replacing drm_master_get with drm_file_get_master.
Signed-off-by: Desmond Cheong Zhi Xi <desmondcheongzx@gmail.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Zack Rusin <zackr@vmware.com>
Signed-off-by: Zack Rusin <zackr@vmware.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210724111824.59266-4-desmondcheongzx@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
Jussi Maki [Sat, 31 Jul 2021 05:57:37 +0000 (05:57 +0000)]
selftests/bpf: Fix xdp_tx.c prog section name
[ Upstream commit
95413846cca37f20000dd095cf6d91f8777129d7 ]
The program type cannot be deduced from 'tx' which causes an invalid
argument error when trying to load xdp_tx.o using the skeleton.
Rename the section name to "xdp" so that libbpf can deduce the type.
Signed-off-by: Jussi Maki <joamaki@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20210731055738.16820-7-joamaki@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
Roy Chan [Mon, 19 Jul 2021 23:00:22 +0000 (19:00 -0400)]
drm/amd/display: fix incorrect CM/TF programming sequence in dwb
[ Upstream commit
781e1e23131cce56fb557e6ec2260480a6bd08cc ]
[How]
the programming sequeune was for old asic.
the correct programming sequeunce should be similar to the one
used in mpc. the fix is copied from the mpc programming sequeunce.
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Signed-off-by: Roy Chan <roy.chan@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Roy Chan [Wed, 21 Jul 2021 23:33:26 +0000 (19:33 -0400)]
drm/amd/display: fix missing writeback disablement if plane is removed
[ Upstream commit
82367e7f22d085092728f45fd5fbb15e3fb997c0 ]
[Why]
If the plane has been removed, the writeback disablement logic
doesn't run
[How]
fix the logic order
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Signed-off-by: Roy Chan <roy.chan@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Sanjay R Mehta [Tue, 3 Aug 2021 12:34:56 +0000 (07:34 -0500)]
thunderbolt: Fix port linking by checking all adapters
[ Upstream commit
42716425ad7e1b6529ec61c260c11176841f4b5f ]
In tb_switch_default_link_ports(), while linking of ports,
only odd-numbered ports (1,3,5..) are considered and even-numbered
ports are not considered.
AMD host router has lane adapters at 2 and 3 and link ports at adapter 2
is not considered due to which lane bonding gets disabled.
Hence added a fix such that all ports are considered during
linking of ports.
Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Signed-off-by: Sanjay R Mehta <sanju.mehta@amd.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Quanyang Wang [Tue, 23 Mar 2021 02:55:01 +0000 (10:55 +0800)]
drm: xlnx: zynqmp: release reset to DP controller before accessing DP registers
[ Upstream commit
a338619bd76011035d462f0f9e8b2f24d7fe5a1e ]
When insmod zynqmp-dpsub.ko after rmmod it, system will hang with the
error log as below:
root@xilinx-zynqmp:~# insmod zynqmp-dpsub.ko
[ 88.391289] [drm] Initialized zynqmp-dpsub 1.0.0
20130509 for
fd4a0000.display on minor 0
[ 88.529906] Console: switching to colour frame buffer device 128x48
[ 88.549402] zynqmp-dpsub
fd4a0000.display: [drm] fb0: zynqmp-dpsubdrm frame buffer device
[ 88.571624] zynqmp-dpsub
fd4a0000.display: ZynqMP DisplayPort Subsystem driver probed
root@xilinx-zynqmp:~# rmmod zynqmp_dpsub
[ 94.023404] Console: switching to colour dummy device 80x25
root@xilinx-zynqmp:~# insmod zynqmp-dpsub.ko
<hang here>
This is because that in zynqmp_dp_probe it tries to access some DP
registers while the DP controller is still in the reset state. When
running "rmmod zynqmp_dpsub", zynqmp_dp_reset(dp, true) in
zynqmp_dp_phy_exit is called to force the DP controller into the reset
state. Then insmod will call zynqmp_dp_probe to program the DP registers,
but at this moment the DP controller hasn't been brought out of the reset
state yet since the function zynqmp_dp_reset(dp, false) is called later and
this will result the system hang.
Releasing the reset to DP controller before any read/write operation to it
will fix this issue. And for symmetry, move zynqmp_dp_reset() call from
zynqmp_dp_phy_exit() to zynqmp_dp_remove().
Signed-off-by: Quanyang Wang <quanyang.wang@windriver.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Quanyang Wang [Wed, 10 Mar 2021 04:59:45 +0000 (12:59 +0800)]
drm: xlnx: zynqmp_dpsub: Call pm_runtime_get_sync before setting pixel clock
[ Upstream commit
a19effb6dbe5bd1be77a6d68eba04dba8993ffeb ]
The Runtime PM subsystem will force the device "
fd4a0000.zynqmp-display"
to enter suspend state while booting if the following conditions are met:
- the usage counter is zero (pm_runtime_get_sync hasn't been called yet)
- no 'active' children (no zynqmp-dp-snd-xx node under dpsub node)
- no other device in the same power domain (dpdma node has no
"power-domains = <&zynqmp_firmware PD_DP>" property)
So there is a scenario as below:
1) DP device enters suspend state <- call zynqmp_gpd_power_off
2) zynqmp_disp_crtc_setup_clock <- configurate register VPLL_FRAC_CFG
3) pm_runtime_get_sync <- call zynqmp_gpd_power_on and clear previous
VPLL_FRAC_CFG configuration
4) clk_prepare_enable(disp->pclk) <- enable failed since VPLL_FRAC_CFG
configuration is corrupted
From above, we can see that pm_runtime_get_sync may clear register
VPLL_FRAC_CFG configuration and result the failure of clk enabling.
Putting pm_runtime_get_sync at the very beginning of the function
zynqmp_disp_crtc_atomic_enable can resolve this issue.
Signed-off-by: Quanyang Wang <quanyang.wang@windriver.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Konrad Dybcio [Wed, 28 Jul 2021 22:20:54 +0000 (00:20 +0200)]
drm/msm/dsi: Fix DSI and DSI PHY regulator config from SDM660
[ Upstream commit
462f7017a6918d152870bfb8852f3c70fd74b296 ]
VDDA is not present and the specified load value is wrong. Fix it.
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Link: https://lore.kernel.org/r/20210728222057.52641-1-konrad.dybcio@somainline.org
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
David Heidelberg [Thu, 15 Jul 2021 06:09:25 +0000 (08:09 +0200)]
drm/msm: mdp4: drop vblank get/put from prepare/complete_commit
[ Upstream commit
56bd931ae506730c9ab1e4cc4bfefa43fc2d18fa ]
msm_atomic is doing vblank get/put's already,
currently there no need to duplicate the effort in MDP4
Fix warning:
...
WARNING: CPU: 3 PID: 79 at drivers/gpu/drm/drm_vblank.c:1194 drm_vblank_put+0x1cc/0x1d4
...
and multiple vblank time-outs:
...
msm 5100000.mdp: vblank time out, crtc=1
...
Tested on Nexus 7 2013 (deb), LTS 5.10.50.
Introduced by:
119ecb7fd3b5 ("drm/msm/mdp4: request vblank during modeset")
Signed-off-by: David Heidelberg <david@ixit.cz>
Link: https://lore.kernel.org/r/20210715060925.7880-1-david@ixit.cz
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Nathan Chancellor [Fri, 6 Aug 2021 19:13:40 +0000 (12:13 -0700)]
net: ethernet: stmmac: Do not use unreachable() in ipq806x_gmac_probe()
[ Upstream commit
4367355dd90942a71641c98c40c74589c9bddf90 ]
When compiling with clang in certain configurations, an objtool warning
appears:
drivers/net/ethernet/stmicro/stmmac/dwmac-ipq806x.o: warning: objtool:
ipq806x_gmac_probe() falls through to next function phy_modes()
This happens because the unreachable annotation in the third switch
statement is not eliminated. The compiler should know that the first
default case would prevent the second and third from being reached as
the comment notes but sanitizer options can make it harder for the
compiler to reason this out.
Help the compiler out by eliminating the unreachable() annotation and
unifying the default case error handling so that there is no objtool
warning, the meaning of the code stays the same, and there is less
duplication.
Reported-by: Sami Tolvanen <samitolvanen@google.com>
Tested-by: Sami Tolvanen <samitolvanen@google.com>
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Rajendra Nayak [Fri, 6 Aug 2021 08:59:45 +0000 (09:59 +0100)]
nvmem: qfprom: Fix up qfprom_disable_fuse_blowing() ordering
[ Upstream commit
11c4b3e264d68ba6dcd52d12dbcfd3f564f2f137 ]
qfprom_disable_fuse_blowing() disables a bunch of resources,
and then does a few register writes in the 'conf' address
space.
It works perhaps because the resources are needed only for the
'raw' register space writes, and that the 'conf' space allows
read/writes regardless.
However that makes the code look confusing, so just move the
register writes before turning off the resources in the
function.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20210806085947.22682-3-srinivas.kandagatla@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Georgi Djakov [Thu, 11 Feb 2021 19:36:37 +0000 (21:36 +0200)]
arm64: dts: qcom: sm8250: Fix epss_l3 unit address
[ Upstream commit
77b53d65dc1e54321ec841912f06bcb558a079c0 ]
The unit address of the epss_l3 node is incorrect and does not match
the address of its "reg" property. Let's fix it.
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Sibi Sankar <sibis@codeaurora.org>
Link: https://lore.kernel.org/r/20210211193637.9737-1-georgi.djakov@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Vinod Koul [Mon, 8 Mar 2021 06:08:17 +0000 (11:38 +0530)]
arm64: dts: qcom: msm8996: don't use underscore in node name
[ Upstream commit
84f3efbe5b4654077608bc2fc027177fe4592321 ]
We have underscore (_) in node name leading to warning:
arch/arm64/boot/dts/qcom/apq8096-db820c.dt.yaml: clocks: $nodename:0: 'clocks' does not match '^([a-z][a-z0-9\\-]+-bus|bus|soc|axi|ahb|apb)(@[0-9a-f]+)?$'
arch/arm64/boot/dts/qcom/apq8096-db820c.dt.yaml: clocks: xo_board: {'type': 'object'} is not allowed for {'compatible': ['fixed-clock'], '#clock-cells': [[0]], 'clock-frequency': [[
19200000]], 'clock-output-names': ['xo_board'], 'phandle': [[115]]}
Fix this by changing node name to use dash (-)
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20210308060826.3074234-10-vkoul@kernel.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Vinod Koul [Mon, 8 Mar 2021 06:08:16 +0000 (11:38 +0530)]
arm64: dts: qcom: msm8994: don't use underscore in node name
[ Upstream commit
8c678beca7ed3fa8a2c6d86f6603bc23400f9ad8 ]
We have underscore (_) in node name leading to warning:
arch/arm64/boot/dts/qcom/msm8994-msft-lumia-octagon-cityman.dt.yaml: clocks: xo_board: {'type': 'object'} is not allowed for {'compatible': ['fixed-clock'], '#clock-cells': [[0]], 'clock-frequency': [[
19200000]], 'phandle': [[26]]}
arch/arm64/boot/dts/qcom/msm8994-msft-lumia-octagon-cityman.dt.yaml: clocks: sleep_clk: {'type': 'object'} is not allowed for {'compatible': ['fixed-clock'], '#clock-cells': [[0]], 'clock-frequency': [[32768]]}
Fix this by changing node name to use dash (-)
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20210308060826.3074234-9-vkoul@kernel.org
[bjorn: Added clock-output-names to satisfy parent_names]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Vinod Koul [Mon, 8 Mar 2021 06:08:18 +0000 (11:38 +0530)]
arm64: dts: qcom: sdm630: don't use underscore in node name
[ Upstream commit
639dfdbecd88ec05bda87b1d5d419afad50af21c ]
We have underscore (_) in node name so fix that up as well.
Fix this by changing node name to use dash (-)
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20210308060826.3074234-11-vkoul@kernel.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Vinod Koul [Mon, 8 Mar 2021 06:08:26 +0000 (11:38 +0530)]
arm64: dts: qcom: ipq6018: drop '0x' from unit address
[ Upstream commit
1b91b8ef60e9a67141e66af3cca532c00f4605fe ]
Nodes need not contain '0x' for the unit address. Drop it to fix the
below warning:
arch/arm64/boot/dts/qcom/ipq6018-cp01-c1.dt.yaml: reserved-memory:
'memory@0x60000' does not match any of the regexes
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20210308060826.3074234-19-vkoul@kernel.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Vinod Koul [Mon, 8 Mar 2021 06:08:25 +0000 (11:38 +0530)]
arm64: dts: qcom: sdm660: use reg value for memory node
[ Upstream commit
c81210e38966cfa1c784364e4035081c3227cf5b ]
memory node like other node should be node@reg, which is missing in this
case, so fix it up
arch/arm64/boot/dts/qcom/ipq8074-hk01.dt.yaml: /: memory: False schema does not allow {'device_type': ['memory'], 'reg': [[0,
1073741824, 0,
536870912]]}
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20210308060826.3074234-18-vkoul@kernel.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Vinod Koul [Mon, 8 Mar 2021 06:08:24 +0000 (11:38 +0530)]
arm64: dts: qcom: ipq8074: fix pci node reg property
[ Upstream commit
52c9887fba71fc8f12d343833fc595c762aac8c7 ]
reg property should be array of values, here it is a single array,
leading to below warning:
arch/arm64/boot/dts/qcom/ipq8074-hk01.dt.yaml: soc: pci@
10000000:reg:0: [
268435456, 3869,
268439328, 168, 557056, 8192,
269484032, 4096] is too long
arch/arm64/boot/dts/qcom/ipq8074-hk01.dt.yaml: soc: pci@
10000000:ranges: 'oneOf' conditional failed, one must be fixed:
arch/arm64/boot/dts/qcom/ipq8074-hk01.dt.yaml: soc: pci@
10000000:ranges: 'oneOf' conditional failed, one must be fixed:
[[
2164260864, 0,
270532608,
270532608, 0, 1048576,
2181038080, 0,
271581184,
271581184, 0,
13631488]] is not of type 'null'
[
2164260864, 0,
270532608,
270532608, 0, 1048576,
2181038080, 0,
271581184,
271581184, 0,
13631488] is too long
arch/arm64/boot/dts/qcom/ipq8074-hk01.dt.yaml: soc: pci@
20000000:reg:0: [
536870912, 3869,
536874784, 168, 524288, 8192,
537919488, 4096] is too long
arch/arm64/boot/dts/qcom/ipq8074-hk01.dt.yaml: soc: pci@
20000000:ranges: 'oneOf' conditional failed, one must be fixed:
arch/arm64/boot/dts/qcom/ipq8074-hk01.dt.yaml: soc: pci@
20000000:ranges: 'oneOf' conditional failed, one must be fixed:
[[
2164260864, 0,
538968064,
538968064, 0, 1048576,
2181038080, 0,
540016640,
540016640, 0,
13631488]] is not of type 'null'
[
2164260864, 0,
538968064,
538968064, 0, 1048576,
2181038080, 0,
540016640,
540016640, 0,
13631488] is too long
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20210308060826.3074234-17-vkoul@kernel.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Sebastian Reichel [Mon, 2 Aug 2021 17:23:08 +0000 (19:23 +0200)]
ARM: dts: imx53-ppd: Fix ACHC entry
[ Upstream commit
cd7cd5b716d594e27a933c12f026d4f2426d7bf4 ]
PPD has only one ACHC device, which effectively is a Kinetis
microcontroller. It has one SPI interface used for normal
communication. Additionally it's possible to flash the device
firmware using NXP's EzPort protocol by correctly driving a
second chip select pin and the device reset pin.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20210802172309.164365-3-sebastian.reichel@collabora.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Tony Lindgren [Tue, 27 Jul 2021 10:35:33 +0000 (13:35 +0300)]
serial: 8250_omap: Handle optional overrun-throttle-ms property
[ Upstream commit
1fe0e1fa3209ad8e9124147775bd27b1d9f04bd4 ]
Handle optional overrun-throttle-ms property as done for 8250_fsl in commit
6d7f677a2afa ("serial: 8250: Rate limit serial port rx interrupts during
input overruns"). This can be used to rate limit the UART interrupts on
noisy lines that end up producing messages like the following:
ttyS ttyS2: 4 input overrun(s)
At least on droid4, the multiplexed USB and UART port is left to UART mode
by the bootloader for a debug console, and if a USB charger is connected
on boot, we get noise on the UART until the PMIC related drivers for PHY
and charger are loaded.
With this patch and overrun-throttle-ms = <500> we avoid the extra rx
interrupts.
Cc: Carl Philipp Klemm <philipp@uvos.xyz>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20210727103533.51547-2-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
AngeloGioacchino Del Regno [Wed, 28 Jul 2021 22:25:11 +0000 (00:25 +0200)]
arm64: dts: qcom: sdm630: Fix TLMM node and pinctrl configuration
[ Upstream commit
36a0d47aee6a8cfd3c6cf4274732d8ef994a25b4 ]
Previous pinctrl configuration was wrong. Fix it and clean up how
multi-pin states are described.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Link: https://lore.kernel.org/r/20210728222542.54269-9-konrad.dybcio@somainline.org
[bjorn: Polished the commit message]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
AngeloGioacchino Del Regno [Wed, 28 Jul 2021 22:25:04 +0000 (00:25 +0200)]
arm64: dts: qcom: sdm630: Rewrite memory map
[ Upstream commit
26e02c98a9ad63eb21b9be4ac92002f555130d3b ]
The memory map was wrong. Fix it.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Link: https://lore.kernel.org/r/20210728222542.54269-2-konrad.dybcio@somainline.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Bob Peterson [Tue, 1 Jun 2021 14:41:40 +0000 (09:41 -0500)]
gfs2: Fix glock recursion in freeze_go_xmote_bh
[ Upstream commit
9d9b16054b7d357afde69a027514c695092b0d22 ]
We must not call gfs2_consist (which does a file system withdraw) from
the freeze glock's freeze_go_xmote_bh function because the withdraw
will try to use the freeze glock, thus causing a glock recursion error.
This patch changes freeze_go_xmote_bh to call function
gfs2_assert_withdraw_delayed instead of gfs2_consist to avoid recursion.
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Evgeny Novikov [Wed, 28 Jul 2021 14:44:32 +0000 (16:44 +0200)]
media: tegra-cec: Handle errors of clk_prepare_enable()
[ Upstream commit
38367073c796a37a61549b1f66a71b3adb03802d ]
tegra_cec_probe() and tegra_cec_resume() ignored possible errors of
clk_prepare_enable(). The patch fixes this.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Evgeny Novikov <novikov@ispras.ru>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Krzysztof Hałasa [Mon, 26 Jul 2021 10:46:28 +0000 (12:46 +0200)]
media: TDA1997x: fix tda1997x_query_dv_timings() return value
[ Upstream commit
7dee1030871a48d4f3c5a74227a4b4188463479a ]
Correctly propagate the tda1997x_detect_std error value.
Signed-off-by: Krzysztof Hałasa <khalasa@piap.pl>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Hans Verkuil [Fri, 23 Jul 2021 08:22:59 +0000 (10:22 +0200)]
media: v4l2-dv-timings.c: fix wrong condition in two for-loops
[ Upstream commit
4108b3e6db31acc4c68133290bbcc87d4db905c9 ]
These for-loops should test against v4l2_dv_timings_presets[i].bt.width,
not if i < v4l2_dv_timings_presets[i].bt.width. Luckily nothing ever broke,
since the smallest width is still a lot higher than the total number of
presets, but it is wrong.
The last item in the presets array is all 0, so the for-loop must stop
when it reaches that sentinel.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reported-by: Krzysztof Hałasa <khalasa@piap.pl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Umang Jain [Fri, 23 Jul 2021 11:22:33 +0000 (13:22 +0200)]
media: imx258: Limit the max analogue gain to 480
[ Upstream commit
f809665ee75fff3f4ea8907f406a66d380aeb184 ]
The range for analog gain mentioned in the datasheet is [0, 480].
The real gain formula mentioned in the datasheet is:
Gain = 512 / (512 – X)
Hence, values larger than 511 clearly makes no sense. The gain
register field is also documented to be of 9-bits in the datasheet.
Certainly, it is enough to infer that, the kernel driver currently
advertises an arbitrary analog gain max. Fix it by rectifying the
value as per the data sheet i.e. 480.
Signed-off-by: Umang Jain <umang.jain@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Laurent Pinchart [Fri, 23 Jul 2021 11:22:32 +0000 (13:22 +0200)]
media: imx258: Rectify mismatch of VTS value
[ Upstream commit
51f93add3669f1b1f540de1cf397815afbd4c756 ]
The frame_length_lines (0x0340) registers are hard-coded as follows:
- 4208x3118
frame_length_lines = 0x0c50
- 2104x1560
frame_length_lines = 0x0638
- 1048x780
frame_length_lines = 0x034c
The driver exposes the V4L2_CID_VBLANK control in read-only mode and
sets its value to vts_def - height, where vts_def is a mode-dependent
value coming from the supported_modes array. It is set using one of
the following macros defined in the driver:
#define IMX258_VTS_30FPS 0x0c98
#define IMX258_VTS_30FPS_2K 0x0638
#define IMX258_VTS_30FPS_VGA 0x034c
There's a clear mismatch in the value for the full resolution mode i.e.
IMX258_VTS_30FPS. Fix it by rectifying the macro with the value set for
the frame_length_lines register as stated above.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Umang Jain <umang.jain@ideasonboard.com>
Reviewed-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Pierre-Louis Bossart [Mon, 2 Aug 2021 15:21:50 +0000 (10:21 -0500)]
ASoC: Intel: update sof_pcm512x quirks
[ Upstream commit
22414cade8dfec25ab94df52b3a4f7aa8edb6120 ]
The default SOF topology enables SSP capture and DMICs, even though
both of these hardware capabilities are not always available in
hardware (specific versions of HiFiberry and DMIC kit needed).
For the SSP capture, this leads to annoying "SP5-Codec: ASoC: no
backend capture" and "streamSSP5-Codec: ASoC: no users capture at
close - state 0" errors.
Update the quirks to match what the topology needs, which also allows
for the ability to remove SSP capture and DMIC support.
BugLink: https://github.com/thesofproject/linux/issues/3061
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Link: https://lore.kernel.org/r/20210802152151.15832-4-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Hans de Goede [Mon, 2 Aug 2021 14:24:56 +0000 (16:24 +0200)]
ASoC: Intel: bytcr_rt5640: Move "Platform Clock" routes to the maps for the matching in-/output
[ Upstream commit
dccd1dfd0770bfd494b68d1135b4547b2c602c42 ]
Move the "Platform Clock" routes for the "Internal Mic" and "Speaker"
routes to the intmic_*_map[] / *_spk_map[] arrays.
This ensures that these "Platform Clock" routes do not get added when the
BYT_RT5640_NO_INTERNAL_MIC_MAP / BYT_RT5640_NO_SPEAKERS quirks are used.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210802142501.991985-2-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Vidya Sagar [Tue, 27 Jul 2021 18:50:55 +0000 (00:20 +0530)]
arm64: tegra: Fix Tegra194 PCIe EP compatible string
[ Upstream commit
bf2942a8b7c38e8cc2d5157b4f0323d7f4e5ec71 ]
The initialization sequence performed by the generic platform driver
pcie-designware-plat.c for a DWC based implementation doesn't work for
Tegra194. Tegra194 has a different initialization sequence requirement
which can only be satisfied by the Tegra194 specific platform driver
pcie-tegra194.c. So, remove the generic compatible string "snps,dw-pcie-ep"
from Tegra194's endpoint controller nodes.
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Nicolas Ferre [Thu, 29 Jul 2021 14:28:27 +0000 (16:28 +0200)]
ARM: dts: at91: use the right property for shutdown controller
[ Upstream commit
818c4593434e81c9971b8fc278215121622c755e ]
The wrong property "atmel,shdwc-debouncer" was used to specify the
debounce delay for the shutdown controler. Replace it with the
documented and implemented property "debounce-delay-us", as mentioned
in v4 driver submission. See:
https://lore.kernel.org/r/
1458134390-23847-3-git-send-email-nicolas.ferre@atmel.com/
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Reported-by: Clément Léger <clement.leger@bootlin.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20210730172729.28093-1-nicolas.ferre@microchip.com/
Signed-off-by: Sasha Levin <sashal@kernel.org>
Yufeng Mo [Fri, 30 Jul 2021 02:19:11 +0000 (10:19 +0800)]
bonding: 3ad: fix the concurrency between __bond_release_one() and bond_3ad_state_machine_handler()
[ Upstream commit
220ade77452c15ecb1ab94c3f8aaeb6d033c3582 ]
Some time ago, I reported a calltrace issue
"did not find a suitable aggregator", please see[1].
After a period of analysis and reproduction, I find
that this problem is caused by concurrency.
Before the problem occurs, the bond structure is like follows:
bond0 - slaver0(eth0) - agg0.lag_ports -> port0 - port1
\
port0
\
slaver1(eth1) - agg1.lag_ports -> NULL
\
port1
If we run 'ifenslave bond0 -d eth1', the process is like below:
excuting __bond_release_one()
|
bond_upper_dev_unlink()[step1]
| | |
| | bond_3ad_lacpdu_recv()
| | ->bond_3ad_rx_indication()
| | spin_lock_bh()
| | ->ad_rx_machine()
| | ->__record_pdu()[step2]
| | spin_unlock_bh()
| | |
| bond_3ad_state_machine_handler()
| spin_lock_bh()
| ->ad_port_selection_logic()
| ->try to find free aggregator[step3]
| ->try to find suitable aggregator[step4]
| ->did not find a suitable aggregator[step5]
| spin_unlock_bh()
| |
| |
bond_3ad_unbind_slave() |
spin_lock_bh()
spin_unlock_bh()
step1: already removed slaver1(eth1) from list, but port1 remains
step2: receive a lacpdu and update port0
step3: port0 will be removed from agg0.lag_ports. The struct is
"agg0.lag_ports -> port1" now, and agg0 is not free. At the
same time, slaver1/agg1 has been removed from the list by step1.
So we can't find a free aggregator now.
step4: can't find suitable aggregator because of step2
step5: cause a calltrace since port->aggregator is NULL
To solve this concurrency problem, put bond_upper_dev_unlink()
after bond_3ad_unbind_slave(). In this way, we can invalid the port
first and skip this port in bond_3ad_state_machine_handler(). This
eliminates the situation that the slaver has been removed from the
list but the port is still valid.
[1]https://lore.kernel.org/netdev/10374.
1611947473@famine/
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Marek Vasut [Sun, 20 Jun 2021 21:24:31 +0000 (23:24 +0200)]
ARM: dts: stm32: Update AV96 adv7513 node per dtbs_check
[ Upstream commit
1e6bc5987a5252948e3411e5a2dbb434fd1ea107 ]
Swap reg and reg-names order and drop adi,input-justification
and adi,input-style to fix the following dtbs_check warnings:
arch/arm/boot/dts/stm32mp157a-dhcor-avenger96.dt.yaml: hdmi-transmitter@3d: adi,input-justification: False schema does not allow ['evenly']
arch/arm/boot/dts/stm32mp157a-dhcor-avenger96.dt.yaml: hdmi-transmitter@3d: adi,input-style: False schema does not allow [[1]]
arch/arm/boot/dts/stm32mp157a-dhcor-avenger96.dt.yaml: hdmi-transmitter@3d: reg-names:1: 'edid' was expected
arch/arm/boot/dts/stm32mp157a-dhcor-avenger96.dt.yaml: hdmi-transmitter@3d: reg-names:2: 'cec' was expected
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@foss.st.com>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Marek Vasut [Thu, 10 Jun 2021 15:03:06 +0000 (17:03 +0200)]
ARM: dts: stm32: Set {bitclock,frame}-master phandles on ST DKx
[ Upstream commit
8aec45d7884f16cc21d668693c5b88bff8df0f02 ]
Fix the following dtbs_check warning:
cs42l51@4a: port:endpoint@0:frame-master: True is not of type 'array'
cs42l51@4a: port:endpoint@0:bitclock-master: True is not of type 'array'
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@foss.st.com>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Marek Vasut [Thu, 10 Jun 2021 15:02:41 +0000 (17:02 +0200)]
ARM: dts: stm32: Set {bitclock,frame}-master phandles on DHCOM SoM
[ Upstream commit
a79e78c391dc074742c855dc0108a88f781d56a3 ]
Fix the following dtbs_check warning:
arch/arm/boot/dts/stm32mp157c-dhcom-pdk2.dt.yaml: codec@a: port:endpoint@0:frame-master: True is not of type 'array'
arch/arm/boot/dts/stm32mp157c-dhcom-pdk2.dt.yaml: codec@a: port:endpoint@0:bitclock-master: True is not of type 'array'
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@foss.st.com>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: kernel@dh-electronics.com
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Zhen Lei [Thu, 22 Jul 2021 03:03:52 +0000 (11:03 +0800)]
workqueue: Fix possible memory leaks in wq_numa_init()
[ Upstream commit
f728c4a9e8405caae69d4bc1232c54ff57b5d20f ]
In error handling branch "if (WARN_ON(node == NUMA_NO_NODE))", the
previously allocated memories are not released. Doing this before
allocating memory eliminates memory leaks.
tj: Note that the condition only occurs when the arch code is pretty broken
and the WARN_ON might as well be BUG_ON().
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Reviewed-by: Lai Jiangshan <jiangshanlai@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Desmond Cheong Zhi Xi [Wed, 28 Jul 2021 07:51:04 +0000 (15:51 +0800)]
Bluetooth: skip invalid hci_sync_conn_complete_evt
[ Upstream commit
92fe24a7db751b80925214ede43f8d2be792ea7b ]
Syzbot reported a corrupted list in kobject_add_internal [1]. This
happens when multiple HCI_EV_SYNC_CONN_COMPLETE event packets with
status 0 are sent for the same HCI connection. This causes us to
register the device more than once which corrupts the kset list.
As this is forbidden behavior, we add a check for whether we're
trying to process the same HCI_EV_SYNC_CONN_COMPLETE event multiple
times for one connection. If that's the case, the event is invalid, so
we report an error that the device is misbehaving, and ignore the
packet.
Link: https://syzkaller.appspot.com/bug?extid=66264bf2fd0476be7e6c
Reported-by: syzbot+66264bf2fd0476be7e6c@syzkaller.appspotmail.com
Tested-by: syzbot+66264bf2fd0476be7e6c@syzkaller.appspotmail.com
Signed-off-by: Desmond Cheong Zhi Xi <desmondcheongzx@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Andy Shevchenko [Tue, 27 Jul 2021 12:51:30 +0000 (15:51 +0300)]
ata: sata_dwc_460ex: No need to call phy_exit() befre phy_init()
[ Upstream commit
3ad4a31620355358316fa08fcfab37b9d6c33347 ]
Last change to device managed APIs cleaned up error path to simple phy_exit()
call, which in some cases has been executed with NULL parameter. This per se
is not a problem, but rather logical misconception: no need to free resource
when it's for sure has not been allocated yet. Fix the driver accordingly.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210727125130.19977-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Martynas Pumputis [Mon, 26 Jul 2021 15:20:01 +0000 (17:20 +0200)]
libbpf: Fix race when pinning maps in parallel
[ Upstream commit
043c5bb3c4f43670ab4fea0b847373ab42d25f3e ]
When loading in parallel multiple programs which use the same to-be
pinned map, it is possible that two instances of the loader will call
bpf_object__create_maps() at the same time. If the map doesn't exist
when both instances call bpf_object__reuse_map(), then one of the
instances will fail with EEXIST when calling bpf_map__pin().
Fix the race by retrying reusing a map if bpf_map__pin() returns
EEXIST. The fix is similar to the one in iproute2:
e4c4685fd6e4 ("bpf:
Fix race condition with map pinning").
Before retrying the pinning, we don't do any special cleaning of an
internal map state. The closer code inspection revealed that it's not
required:
- bpf_object__create_map(): map->inner_map is destroyed after a
successful call, map->fd is closed if pinning fails.
- bpf_object__populate_internal_map(): created map elements is
destroyed upon close(map->fd).
- init_map_slots(): slots are freed after their initialization.
Signed-off-by: Martynas Pumputis <m@lambda.lt>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20210726152001.34845-1-m@lambda.lt
Signed-off-by: Sasha Levin <sashal@kernel.org>
Juhee Kang [Tue, 27 Jul 2021 04:10:55 +0000 (04:10 +0000)]
samples: bpf: Fix tracex7 error raised on the missing argument
[ Upstream commit
7d07006f05922b95518be403f08ef8437b67aa32 ]
The current behavior of 'tracex7' doesn't consist with other bpf samples
tracex{1..6}. Other samples do not require any argument to run with, but
tracex7 should be run with btrfs device argument. (it should be executed
with test_override_return.sh)
Currently, tracex7 doesn't have any description about how to run this
program and raises an unexpected error. And this result might be
confusing since users might not have a hunch about how to run this
program.
// Current behavior
# ./tracex7
sh: 1: Syntax error: word unexpected (expecting ")")
// Fixed behavior
# ./tracex7
ERROR: Run with the btrfs device argument!
In order to fix this error, this commit adds logic to report a message
and exit when running this program with a missing argument.
Additionally in test_override_return.sh, there is a problem with
multiple directory(tmpmnt) creation. So in this commit adds a line with
removing the directory with every execution.
Signed-off-by: Juhee Kang <claudiajkang@gmail.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Acked-by: Yonghong Song <yhs@fb.com>
Link: https://lore.kernel.org/bpf/20210727041056.23455-1-claudiajkang@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
Christophe JAILLET [Wed, 21 Jul 2021 08:45:11 +0000 (10:45 +0200)]
staging: ks7010: Fix the initialization of the 'sleep_status' structure
[ Upstream commit
56315e55119c0ea57e142b6efb7c31208628ad86 ]
'sleep_status' has 3 atomic_t members. Initialize the 3 of them instead of
initializing only 2 of them and setting 0 twice to the same variable.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/d2e52a33a9beab41879551d0ae2fdfc99970adab.1626856991.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Greg Kroah-Hartman [Mon, 26 Jul 2021 13:07:17 +0000 (15:07 +0200)]
serial: 8250_pci: make setup_port() parameters explicitly unsigned
[ Upstream commit
3a96e97ab4e835078e6f27b7e1c0947814df3841 ]
The bar and offset parameters to setup_port() are used in pointer math,
and while it would be very difficult to get them to wrap as a negative
number, just be "safe" and make them unsigned so that static checkers do
not trip over them unintentionally.
Cc: Jiri Slaby <jirislaby@kernel.org>
Reported-by: Jordy Zomer <jordy@pwning.systems>
Link: https://lore.kernel.org/r/20210726130717.2052096-1-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Jiri Slaby [Fri, 23 Jul 2021 07:43:11 +0000 (09:43 +0200)]
hvsi: don't panic on tty_register_driver failure
[ Upstream commit
7ccbdcc4d08a6d7041e4849219bbb12ffa45db4c ]
The alloc_tty_driver failure is handled gracefully in hvsi_init. But
tty_register_driver is not. panic is called if that one fails.
So handle the failure of tty_register_driver gracefully too. This will
keep at least the console functional as it was enabled earlier by
console_initcall in hvsi_console_init. Instead of shooting down the
whole system.
This means, we disable interrupts and restore hvsi_wait back to
poll_for_state().
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210723074317.32690-3-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Jiri Slaby [Fri, 23 Jul 2021 07:43:10 +0000 (09:43 +0200)]
xtensa: ISS: don't panic in rs_init
[ Upstream commit
23411c720052ad860b3e579ee4873511e367130a ]
While alloc_tty_driver failure in rs_init would mean we have much bigger
problem, there is no reason to panic when tty_register_driver fails
there. It can fail for various reasons.
So handle the failure gracefully. Actually handle them both while at it.
This will make at least the console functional as it was enabled earlier
by console_initcall in iss_console_init. Instead of shooting down the
whole system.
We move tty_port_init() after alloc_tty_driver(), so that we don't need
to destroy the port in case the latter function fails.
Cc: Chris Zankel <chris@zankel.net>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: linux-xtensa@linux-xtensa.org
Acked-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210723074317.32690-2-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Maciej W. Rozycki [Sat, 26 Jun 2021 04:11:51 +0000 (06:11 +0200)]
serial: 8250: Define RX trigger levels for OxSemi 950 devices
[ Upstream commit
d7aff291d069c4418285f3c8ee27b0ff67ce5998 ]
Oxford Semiconductor 950 serial port devices have a 128-byte FIFO and in
the enhanced (650) mode, which we select in `autoconfig_has_efr' with
the ECB bit set in the EFR register, they support the receive interrupt
trigger level selectable with FCR bits 7:6 from the set of 16, 32, 112,
120. This applies to the original OX16C950 discrete UART[1] as well as
950 cores embedded into more complex devices.
For these devices we set the default to 112, which sets an excessively
high level of 112 or 7/8 of the FIFO capacity, unlike with other port
types where we choose at most 1/2 of their respective FIFO capacities.
Additionally we don't make the trigger level configurable. Consequently
frequent input overruns happen with high bit rates where hardware flow
control cannot be used (e.g. terminal applications) even with otherwise
highly-performant systems.
Lower the default receive interrupt trigger level to 32 then, and make
it configurable. Document the trigger levels along with other port
types, including the set of 16, 32, 64, 112 for the transmit interrupt
as well[2].
References:
[1] "OX16C950 rev B High Performance UART with 128 byte FIFOs", Oxford
Semiconductor, Inc., DS-0031, Sep 05, Table 10: "Receiver Trigger
Levels", p. 22
[2] same, Table 9: "Transmit Interrupt Trigger Levels", p. 22
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2106260608480.37803@angie.orcam.me.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Niklas Schnelle [Thu, 8 Jul 2021 12:55:42 +0000 (14:55 +0200)]
s390: make PCI mio support a machine flag
[ Upstream commit
3322ba0d7bea1e24ae464418626f6a15b69533ab ]
Kernel support for the newer PCI mio instructions can be toggled off
with the pci=nomio command line option which needs to integrate with
common code PCI option parsing. However this option then toggles static
branches which can't be toggled yet in an early_param() call.
Thus commit
9964f396f1d0 ("s390: fix setting of mio addressing control")
moved toggling the static branches to the PCI init routine.
With this setup however we can't check for mio support outside the PCI
code during early boot, i.e. before switching the static branches, which
we need to be able to export this as an ELF HWCAP.
Improve on this by turning mio availability into a machine flag that
gets initially set based on CONFIG_PCI and the facility bit and gets
toggled off if pci=nomio is found during PCI option parsing allowing
simple access to this machine flag after early init.
Reviewed-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Heiko Carstens [Mon, 12 Jul 2021 17:26:01 +0000 (19:26 +0200)]
s390/jump_label: print real address in a case of a jump label bug
[ Upstream commit
5492886c14744d239e87f1b0b774b5a341e755cc ]
In case of a jump label print the real address of the piece of code
where a mismatch was detected. This is right before the system panics,
so there is nothing revealed.
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Gustavo A. R. Silva [Mon, 26 Jul 2021 19:25:11 +0000 (14:25 -0500)]
flow_dissector: Fix out-of-bounds warnings
[ Upstream commit
323e0cb473e2a8706ff162b6b4f4fa16023c9ba7 ]
Fix the following out-of-bounds warnings:
net/core/flow_dissector.c: In function '__skb_flow_dissect':
>> net/core/flow_dissector.c:1104:4: warning: 'memcpy' offset [24, 39] from the object at '<unknown>' is out of the bounds of referenced subobject 'saddr' with type 'struct in6_addr' at offset 8 [-Warray-bounds]
1104 | memcpy(&key_addrs->v6addrs, &iph->saddr,
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
1105 | sizeof(key_addrs->v6addrs));
| ~~~~~~~~~~~~~~~~~~~~~~~~~~~
In file included from include/linux/ipv6.h:5,
from net/core/flow_dissector.c:6:
include/uapi/linux/ipv6.h:133:18: note: subobject 'saddr' declared here
133 | struct in6_addr saddr;
| ^~~~~
>> net/core/flow_dissector.c:1059:4: warning: 'memcpy' offset [16, 19] from the object at '<unknown>' is out of the bounds of referenced subobject 'saddr' with type 'unsigned int' at offset 12 [-Warray-bounds]
1059 | memcpy(&key_addrs->v4addrs, &iph->saddr,
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
1060 | sizeof(key_addrs->v4addrs));
| ~~~~~~~~~~~~~~~~~~~~~~~~~~~
In file included from include/linux/ip.h:17,
from net/core/flow_dissector.c:5:
include/uapi/linux/ip.h:103:9: note: subobject 'saddr' declared here
103 | __be32 saddr;
| ^~~~~
The problem is that the original code is trying to copy data into a
couple of struct members adjacent to each other in a single call to
memcpy(). So, the compiler legitimately complains about it. As these
are just a couple of members, fix this by copying each one of them in
separate calls to memcpy().
This helps with the ongoing efforts to globally enable -Warray-bounds
and get us closer to being able to tighten the FORTIFY_SOURCE routines
on memcpy().
Link: https://github.com/KSPP/linux/issues/109
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/lkml/d5ae2e65-1f18-2577-246f-bada7eee6ccd@intel.com/
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Gustavo A. R. Silva [Mon, 26 Jul 2021 19:52:51 +0000 (14:52 -0500)]
ipv4: ip_output.c: Fix out-of-bounds warning in ip_copy_addrs()
[ Upstream commit
6321c7acb82872ef6576c520b0e178eaad3a25c0 ]
Fix the following out-of-bounds warning:
In function 'ip_copy_addrs',
inlined from '__ip_queue_xmit' at net/ipv4/ip_output.c:517:2:
net/ipv4/ip_output.c:449:2: warning: 'memcpy' offset [40, 43] from the object at 'fl' is out of the bounds of referenced subobject 'saddr' with type 'unsigned int' at offset 36 [-Warray-bounds]
449 | memcpy(&iph->saddr, &fl4->saddr,
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
450 | sizeof(fl4->saddr) + sizeof(fl4->daddr));
| ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
The problem is that the original code is trying to copy data into a
couple of struct members adjacent to each other in a single call to
memcpy(). This causes a legitimate compiler warning because memcpy()
overruns the length of &iph->saddr and &fl4->saddr. As these are just
a couple of struct members, fix this by using direct assignments,
instead of memcpy().
This helps with the ongoing efforts to globally enable -Warray-bounds
and get us closer to being able to tighten the FORTIFY_SOURCE routines
on memcpy().
Link: https://github.com/KSPP/linux/issues/109
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/lkml/d5ae2e65-1f18-2577-246f-bada7eee6ccd@intel.com/
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Zheyu Ma [Mon, 26 Jul 2021 10:03:55 +0000 (10:03 +0000)]
video: fbdev: riva: Error out if 'pixclock' equals zero
[ Upstream commit
f92763cb0feba247e0939ed137b495601fd072a5 ]
The userspace program could pass any values to the driver through
ioctl() interface. If the driver doesn't check the value of 'pixclock',
it may cause divide error.
Fix this by checking whether 'pixclock' is zero first.
The following log reveals it:
[ 33.396850] divide error: 0000 [#1] PREEMPT SMP KASAN PTI
[ 33.396864] CPU: 5 PID: 11754 Comm: i740 Not tainted 5.14.0-rc2-00513-gac532c9bbcfb-dirty #222
[ 33.396883] RIP: 0010:riva_load_video_mode+0x417/0xf70
[ 33.396969] Call Trace:
[ 33.396973] ? debug_smp_processor_id+0x1c/0x20
[ 33.396984] ? tick_nohz_tick_stopped+0x1a/0x90
[ 33.396996] ? rivafb_copyarea+0x3c0/0x3c0
[ 33.397003] ? wake_up_klogd.part.0+0x99/0xd0
[ 33.397014] ? vprintk_emit+0x110/0x4b0
[ 33.397024] ? vprintk_default+0x26/0x30
[ 33.397033] ? vprintk+0x9c/0x1f0
[ 33.397041] ? printk+0xba/0xed
[ 33.397054] ? record_print_text.cold+0x16/0x16
[ 33.397063] ? __kasan_check_read+0x11/0x20
[ 33.397074] ? profile_tick+0xc0/0x100
[ 33.397084] ? __sanitizer_cov_trace_const_cmp4+0x24/0x80
[ 33.397094] ? riva_set_rop_solid+0x2a0/0x2a0
[ 33.397102] rivafb_set_par+0xbe/0x610
[ 33.397111] ? riva_set_rop_solid+0x2a0/0x2a0
[ 33.397119] fb_set_var+0x5bf/0xeb0
[ 33.397127] ? fb_blank+0x1a0/0x1a0
[ 33.397134] ? lock_acquire+0x1ef/0x530
[ 33.397143] ? lock_release+0x810/0x810
[ 33.397151] ? lock_is_held_type+0x100/0x140
[ 33.397159] ? ___might_sleep+0x1ee/0x2d0
[ 33.397170] ? __mutex_lock+0x620/0x1190
[ 33.397180] ? trace_hardirqs_on+0x6a/0x1c0
[ 33.397190] do_fb_ioctl+0x31e/0x700
Signed-off-by: Zheyu Ma <zheyuma97@gmail.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/1627293835-17441-4-git-send-email-zheyuma97@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
Zheyu Ma [Mon, 26 Jul 2021 10:03:54 +0000 (10:03 +0000)]
video: fbdev: kyro: Error out if 'pixclock' equals zero
[ Upstream commit
1520b4b7ba964f8eec2e7dd14c571d50de3e5191 ]
The userspace program could pass any values to the driver through
ioctl() interface. if the driver doesn't check the value of 'pixclock',
it may cause divide error because the value of 'lineclock' and
'frameclock' will be zero.
Fix this by checking whether 'pixclock' is zero in kyrofb_check_var().
The following log reveals it:
[ 103.073930] divide error: 0000 [#1] PREEMPT SMP KASAN PTI
[ 103.073942] CPU: 4 PID: 12483 Comm: syz-executor Not tainted 5.14.0-rc2-00478-g2734d6c1b1a0-dirty #118
[ 103.073959] RIP: 0010:kyrofb_set_par+0x316/0xc80
[ 103.074045] Call Trace:
[ 103.074048] ? ___might_sleep+0x1ee/0x2d0
[ 103.074060] ? kyrofb_ioctl+0x330/0x330
[ 103.074069] fb_set_var+0x5bf/0xeb0
[ 103.074078] ? fb_blank+0x1a0/0x1a0
[ 103.074085] ? lock_acquire+0x3bd/0x530
[ 103.074094] ? lock_release+0x810/0x810
[ 103.074103] ? ___might_sleep+0x1ee/0x2d0
[ 103.074114] ? __mutex_lock+0x620/0x1190
[ 103.074126] ? trace_hardirqs_on+0x6a/0x1c0
[ 103.074137] do_fb_ioctl+0x31e/0x700
[ 103.074144] ? fb_getput_cmap+0x280/0x280
[ 103.074152] ? rcu_read_lock_sched_held+0x11/0x80
[ 103.074162] ? rcu_read_lock_sched_held+0x11/0x80
[ 103.074171] ? __sanitizer_cov_trace_switch+0x67/0xf0
[ 103.074181] ? __sanitizer_cov_trace_const_cmp2+0x20/0x80
[ 103.074191] ? do_vfs_ioctl+0x14b/0x16c0
[ 103.074199] ? vfs_fileattr_set+0xb60/0xb60
[ 103.074207] ? rcu_read_lock_sched_held+0x11/0x80
[ 103.074216] ? lock_release+0x483/0x810
[ 103.074224] ? __fget_files+0x217/0x3d0
[ 103.074234] ? __fget_files+0x239/0x3d0
[ 103.074243] ? do_fb_ioctl+0x700/0x700
[ 103.074250] fb_ioctl+0xe6/0x130
Signed-off-by: Zheyu Ma <zheyuma97@gmail.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/1627293835-17441-3-git-send-email-zheyuma97@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
Zheyu Ma [Mon, 26 Jul 2021 10:03:53 +0000 (10:03 +0000)]
video: fbdev: asiliantfb: Error out if 'pixclock' equals zero
[ Upstream commit
b36b242d4b8ea178f7fd038965e3cac7f30c3f09 ]
The userspace program could pass any values to the driver through
ioctl() interface. If the driver doesn't check the value of 'pixclock',
it may cause divide error.
Fix this by checking whether 'pixclock' is zero first.
The following log reveals it:
[ 43.861711] divide error: 0000 [#1] PREEMPT SMP KASAN PTI
[ 43.861737] CPU: 2 PID: 11764 Comm: i740 Not tainted 5.14.0-rc2-00513-gac532c9bbcfb-dirty #224
[ 43.861756] RIP: 0010:asiliantfb_check_var+0x4e/0x730
[ 43.861843] Call Trace:
[ 43.861848] ? asiliantfb_remove+0x190/0x190
[ 43.861858] fb_set_var+0x2e4/0xeb0
[ 43.861866] ? fb_blank+0x1a0/0x1a0
[ 43.861873] ? lock_acquire+0x1ef/0x530
[ 43.861884] ? lock_release+0x810/0x810
[ 43.861892] ? lock_is_held_type+0x100/0x140
[ 43.861903] ? ___might_sleep+0x1ee/0x2d0
[ 43.861914] ? __mutex_lock+0x620/0x1190
[ 43.861921] ? do_fb_ioctl+0x313/0x700
[ 43.861929] ? mutex_lock_io_nested+0xfa0/0xfa0
[ 43.861936] ? __this_cpu_preempt_check+0x1d/0x30
[ 43.861944] ? _raw_spin_unlock_irqrestore+0x46/0x60
[ 43.861952] ? lockdep_hardirqs_on+0x59/0x100
[ 43.861959] ? _raw_spin_unlock_irqrestore+0x46/0x60
[ 43.861967] ? trace_hardirqs_on+0x6a/0x1c0
[ 43.861978] do_fb_ioctl+0x31e/0x700
Signed-off-by: Zheyu Ma <zheyuma97@gmail.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/1627293835-17441-2-git-send-email-zheyuma97@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
Jernej Skrabec [Thu, 22 Jul 2021 16:12:18 +0000 (18:12 +0200)]
arm64: dts: allwinner: h6: tanix-tx6: Fix regulator node names
[ Upstream commit
7ab1f6539762946de06ca14d7401ae123821bc40 ]
Regulator node names don't reflect class of the device. Fix that by
prefixing names with "regulator-".
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210722161220.51181-2-jernej.skrabec@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
Geert Uytterhoeven [Wed, 14 Jul 2021 09:48:06 +0000 (11:48 +0200)]
drm/bridge: nwl-dsi: Avoid potential multiplication overflow on 32-bit
[ Upstream commit
47956bc86ee4e8530cac386a04f62a6095f7afbe ]
As nwl_dsi.lanes is u32, and NSEC_PER_SEC is 1000000000L, the second
multiplication in
dsi->lanes * 8 * NSEC_PER_SEC
will overflow on a 32-bit platform. Fix this by making the constant
unsigned long long, forcing 64-bit arithmetic.
As iMX8 is arm64, this driver is currently used on 64-bit platforms
only, where long is 64-bit, so this cannot happen. But the issue will
start to happen when the driver is reused for a 32-bit SoC (e.g.
i.MX7ULP), or when code is copied for a new driver.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/ebb82941a86b4e35c4fcfb1ef5a5cfad7c1fceab.1626255956.git.geert+renesas@glider.be
Signed-off-by: Sasha Levin <sashal@kernel.org>
Johan Almbladh [Wed, 21 Jul 2021 10:38:22 +0000 (12:38 +0200)]
bpf/tests: Do not PASS tests without actually testing the result
[ Upstream commit
2b7e9f25e590726cca76700ebdb10e92a7a72ca1 ]
Each test case can have a set of sub-tests, where each sub-test can
run the cBPF/eBPF test snippet with its own data_size and expected
result. Before, the end of the sub-test array was indicated by both
data_size and result being zero. However, most or all of the internal
eBPF tests has a data_size of zero already. When such a test also had
an expected value of zero, the test was never run but reported as
PASS anyway.
Now the test runner always runs the first sub-test, regardless of the
data_size and result values. The sub-test array zero-termination only
applies for any additional sub-tests.
There are other ways fix it of course, but this solution at least
removes the surprise of eBPF tests with a zero result always succeeding.
Signed-off-by: Johan Almbladh <johan.almbladh@anyfinetworks.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20210721103822.3755111-1-johan.almbladh@anyfinetworks.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
Johan Almbladh [Wed, 21 Jul 2021 10:40:58 +0000 (12:40 +0200)]
bpf/tests: Fix copy-and-paste error in double word test
[ Upstream commit
ae7f47041d928b1a2f28717d095b4153c63cbf6a ]
This test now operates on DW as stated instead of W, which was
already covered by another test.
Signed-off-by: Johan Almbladh <johan.almbladh@anyfinetworks.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20210721104058.3755254-1-johan.almbladh@anyfinetworks.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
Anson Jacob [Tue, 20 Jul 2021 15:00:44 +0000 (11:00 -0400)]
drm/amd/amdgpu: Update debugfs link_settings output link_rate field in hex
[ Upstream commit
1a394b3c3de2577f200cb623c52a5c2b82805cec ]
link_rate is updated via debugfs using hex values, set it to output
in hex as well.
eg: Resolution: 1920x1080@144Hz
cat /sys/kernel/debug/dri/0/DP-1/link_settings
Current: 4 0x14 0 Verified: 4 0x1e 0 Reported: 4 0x1e 16 Preferred: 0 0x0 0
echo "4 0x1e" > /sys/kernel/debug/dri/0/DP-1/link_settings
cat /sys/kernel/debug/dri/0/DP-1/link_settings
Current: 4 0x1e 0 Verified: 4 0x1e 0 Reported: 4 0x1e 16 Preferred: 4 0x1e 0
Signed-off-by: Anson Jacob <Anson.Jacob@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Oak Zeng [Wed, 14 Jul 2021 14:50:37 +0000 (09:50 -0500)]
drm/amdgpu: Fix a printing message
[ Upstream commit
95f71f12aa45d65b7f2ccab95569795edffd379a ]
The printing message "PSP loading VCN firmware" is mis-leading because
people might think driver is loading VCN firmware. Actually when this
message is printed, driver is just preparing some VCN ucode, not loading
VCN firmware yet. The actual VCN firmware loading will be in the PSP block
hw_init. Fix the printing message
Signed-off-by: Oak Zeng <Oak.Zeng@amd.com>
Reviewed-by: Christian Konig <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Arnd Bergmann [Thu, 22 Jul 2021 14:28:59 +0000 (16:28 +0200)]
ethtool: improve compat ioctl handling
[ Upstream commit
dd98d2895de6485c884a9cb42de69fed02826fa4 ]
The ethtool compat ioctl handling is hidden away in net/socket.c,
which introduces a couple of minor oddities:
- The implementation may end up diverging, as seen in the RXNFC
extension in commit
84a1d9c48200 ("net: ethtool: extend RXNFC
API to support RSS spreading of filter matches") that does not work
in compat mode.
- Most architectures do not need the compat handling at all
because u64 and compat_u64 have the same alignment.
- On x86, the conversion is done for both x32 and i386 user space,
but it's actually wrong to do it for x32 and cannot work there.
- On 32-bit Arm, it never worked for compat oabi user space, since
that needs to do the same conversion but does not.
- It would be nice to get rid of both compat_alloc_user_space()
and copy_in_user() throughout the kernel.
None of these actually seems to be a serious problem that real
users are likely to encounter, but fixing all of them actually
leads to code that is both shorter and more readable.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Niklas Söderlund [Thu, 22 Jul 2021 11:25:02 +0000 (13:25 +0200)]
nfp: fix return statement in nfp_net_parse_meta()
[ Upstream commit
4431531c482a2c05126caaa9fcc5053a4a5c495b ]
The return type of the function is bool and while NULL do evaluate to
false it's not very nice, fix this by explicitly returning false. There
is no functional change.
Signed-off-by: Niklas Söderlund <niklas.soderlund@corigine.com>
Signed-off-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Yang Yingliang [Thu, 17 Jun 2021 07:23:29 +0000 (09:23 +0200)]
media: atomisp: pci: fix error return code in atomisp_pci_probe()
[ Upstream commit
d14e272958bdfdc40dcafb827d24ba6fdafa9d52 ]
If init_atomisp_wdts() fails, atomisp_pci_probe() need return
error code.
Link: https://lore.kernel.org/linux-media/20210617072329.1233662-1-yangyingliang@huawei.com
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Dinghao Liu [Thu, 8 Apr 2021 08:18:43 +0000 (10:18 +0200)]
media: atomisp: Fix runtime PM imbalance in atomisp_pci_probe
[ Upstream commit
672fe1cf145ab9978c62eb827d6a16aa6b63994b ]
When hmm_pool_register() fails, a pairing PM usage counter
increment is needed to keep the counter balanced. It's the
same for the following error paths.
Link: https://lore.kernel.org/linux-media/20210408081850.24278-1-dinghao.liu@zju.edu.cn
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Acked-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Evgeny Novikov [Sat, 10 Jul 2021 12:04:32 +0000 (14:04 +0200)]
media: platform: stm32: unprepare clocks at handling errors in probe
[ Upstream commit
055d2db28ec2fa3ab5c527c5604f1b32b89fa13a ]
stm32_cec_probe() did not unprepare clocks on error handling paths. The
patch fixes that.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Evgeny Novikov <novikov@ispras.ru>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Ezequiel Garcia [Mon, 19 Jul 2021 20:52:33 +0000 (22:52 +0200)]
media: hantro: vp8: Move noisy WARN_ON to vpu_debug
[ Upstream commit
6ad61a7847da09b6261824accb539d05bcdfef65 ]
When the VP8 decoders can't find a reference frame,
the driver falls back to the current output frame.
This will probably produce some undesirable results,
leading to frame corruption, but shouldn't cause
noisy warnings.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Acked-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Tested-by: Alex Bee <knaerzche@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Oliver Logush [Wed, 23 Jun 2021 19:04:04 +0000 (15:04 -0400)]
drm/amd/display: Fix timer_per_pixel unit error
[ Upstream commit
23e55639b87fb16a9f0f66032ecb57060df6c46c ]
[why]
The units of the time_per_pixel variable were incorrect, this had to be
changed for the code to properly function.
[how]
The change was very straightforward, only required one line of code to
be changed where the calculation was done.
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Oliver Logush <oliver.logush@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Shuah Khan [Thu, 8 Jul 2021 03:18:27 +0000 (21:18 -0600)]
selftests: firmware: Fix ignored return val of asprintf() warn
[ Upstream commit
fe968ca2cac91888310b143a483123c84906e3fc ]
Fix the following ingonred return val of asprintf() warn during
build:
cc -Wall -O2 fw_namespace.c -o ../tools/testing/selftests/firmware/fw_namespace
fw_namespace.c: In function ‘main’:
fw_namespace.c:132:2: warning: ignoring return value of ‘asprintf’ declared with attribute ‘warn_unused_result’ [-Wunused-result]
132 | asprintf(&fw_path, "/lib/firmware/%s", fw_name);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Link: https://lore.kernel.org/r/20210708031827.51293-1-skhan@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Laurentiu Tudor [Thu, 15 Jul 2021 14:07:18 +0000 (17:07 +0300)]
bus: fsl-mc: fix mmio base address for child DPRCs
[ Upstream commit
8990f96a012f42543005b07d9e482694192e9309 ]
Some versions of the MC firmware wrongly report 0 for register base
address of the DPMCP associated with child DPRC objects thus rendering
them unusable. This is particularly troublesome in ACPI boot scenarios
where the legacy way of extracting this base address from the device
tree does not apply.
Given that DPMCPs share the same base address, workaround this by using
the base address extracted from the root DPRC container.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Link: https://lore.kernel.org/r/20210715140718.8513-8-laurentiu.tudor@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Zheyu Ma [Wed, 14 Jul 2021 05:53:23 +0000 (05:53 +0000)]
tty: serial: jsm: hold port lock when reporting modem line changes
[ Upstream commit
240e126c28df084222f0b661321e8e3ecb0d232e ]
uart_handle_dcd_change() requires a port lock to be held and will emit a
warning when lockdep is enabled.
Held corresponding lock to fix the following warnings.
[ 132.528648] WARNING: CPU: 5 PID: 11600 at drivers/tty/serial/serial_core.c:3046 uart_handle_dcd_change+0xf4/0x120
[ 132.530482] Modules linked in:
[ 132.531050] CPU: 5 PID: 11600 Comm: jsm Not tainted 5.14.0-rc1-00003-g7fef2edf7cc7-dirty #31
[ 132.535268] RIP: 0010:uart_handle_dcd_change+0xf4/0x120
[ 132.557100] Call Trace:
[ 132.557562] ? __free_pages+0x83/0xb0
[ 132.558213] neo_parse_modem+0x156/0x220
[ 132.558897] neo_param+0x399/0x840
[ 132.559495] jsm_tty_open+0x12f/0x2d0
[ 132.560131] uart_startup.part.18+0x153/0x340
[ 132.560888] ? lock_is_held_type+0xe9/0x140
[ 132.561660] uart_port_activate+0x7f/0xe0
[ 132.562351] ? uart_startup.part.18+0x340/0x340
[ 132.563003] tty_port_open+0x8d/0xf0
[ 132.563523] ? uart_set_options+0x1e0/0x1e0
[ 132.564125] uart_open+0x24/0x40
[ 132.564604] tty_open+0x15c/0x630
Signed-off-by: Zheyu Ma <zheyuma97@gmail.com>
Link: https://lore.kernel.org/r/1626242003-3809-1-git-send-email-zheyuma97@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>