sctp: not allow transport timeout value less than HZ/5 for hb_timer

[ Upstream commit 1d88ba1ebb2763aa86172cd7ca05dedbeccc0d35 ]

syzbot reported a rcu_sched self-detected stall on CPU which is caused
by too small value set on rto_min with SCTP_RTOINFO sockopt. With this
value, hb_timer will get stuck there, as in its timer handler it starts
this timer again with this value, then goes to the timer handler again.

This problem is there since very beginning, and thanks to Eric for the
reproducer shared from a syzbot mail.

This patch fixes it by not allowing sctp_transport_timeout to return a
smaller value than HZ/5 for hb_timer, which is based on TCP's min rto.

Note that it doesn't fix this issue by limiting rto_min, as some users
are still using small rto and no proper value was found for it yet.

Reported-by: syzbot+3dcd59a1f907245f891f@syzkaller.appspotmail.com
Suggested-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

qed: Fix mask for physical address in ILT entry

[ Upstream commit fdd13dd350dda1826579eb5c333d76b14513b812 ]

ILT entry requires 12 bit right shifted physical address.
Existing mask for ILT entry of physical address i.e.
ILT_ENTRY_PHY_ADDR_MASK is not sufficient to handle 64bit
address because upper 8 bits of 64 bit address were getting
masked which resulted in completer abort error on
PCIe bus due to invalid address.

Fix that mask to handle 64bit physical address.

Fixes: fe56b9e6a8d9 ("qed: Add module with basic common support")
Signed-off-by: Shahed Shaikh <shahed.shaikh@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

packet: fix reserve calculation

[ Upstream commit 9aad13b087ab0a588cd68259de618f100053360e ]

Commit b84bbaf7a6c8 ("packet: in packet_snd start writing at link
layer allocation") ensures that packet_snd always starts writing
the link layer header in reserved headroom allocated for this
purpose.

This is needed because packets may be shorter than hard_header_len,
in which case the space up to hard_header_len may be zeroed. But
that necessary padding is not accounted for in skb->len.

The fix, however, is buggy. It calls skb_push, which grows skb->len
when moving skb->data back. But in this case packet length should not
change.

Instead, call skb_reserve, which moves both skb->data and skb->tail
back, without changing length.

Fixes: b84bbaf7a6c8 ("packet: in packet_snd start writing at link layer allocation")
Reported-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: usb: cdc_mbim: add flag FLAG_SEND_ZLP

[ Upstream commit 9f7c728332e8966084242fcd951aa46583bc308c ]

Testing Telit LM940 with ICMP packets > 14552 bytes revealed that
the modem needs FLAG_SEND_ZLP to properly work, otherwise the cdc
mbim data interface won't be anymore responsive.

Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net/packet: refine check for priv area size

[ Upstream commit eb73190f4fbeedf762394e92d6a4ec9ace684c88 ]

syzbot was able to trick af_packet again [1]

Various commits tried to address the problem in the past,
but failed to take into account V3 header size.

[1]

tpacket_rcv: packet too big, clamped from 72 to 4294967224. macoff=96
BUG: KASAN: use-after-free in prb_run_all_ft_ops net/packet/af_packet.c:1016 [inline]
BUG: KASAN: use-after-free in prb_fill_curr_block.isra.59+0x4e5/0x5c0 net/packet/af_packet.c:1039
Write of size 2 at addr ffff8801cb62000e by task kworker/1:2/2106

CPU: 1 PID: 2106 Comm: kworker/1:2 Not tainted 4.17.0-rc7+ #77
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Workqueue: ipv6_addrconf addrconf_dad_work
Call Trace:
 __dump_stack lib/dump_stack.c:77 [inline]
 dump_stack+0x1b9/0x294 lib/dump_stack.c:113
 print_address_description+0x6c/0x20b mm/kasan/report.c:256
 kasan_report_error mm/kasan/report.c:354 [inline]
 kasan_report.cold.7+0x242/0x2fe mm/kasan/report.c:412
 __asan_report_store2_noabort+0x17/0x20 mm/kasan/report.c:436
 prb_run_all_ft_ops net/packet/af_packet.c:1016 [inline]
 prb_fill_curr_block.isra.59+0x4e5/0x5c0 net/packet/af_packet.c:1039
 __packet_lookup_frame_in_block net/packet/af_packet.c:1094 [inline]
 packet_current_rx_frame net/packet/af_packet.c:1117 [inline]
 tpacket_rcv+0x1866/0x3340 net/packet/af_packet.c:2282
 dev_queue_xmit_nit+0x891/0xb90 net/core/dev.c:2018
 xmit_one net/core/dev.c:3049 [inline]
 dev_hard_start_xmit+0x16b/0xc10 net/core/dev.c:3069
 __dev_queue_xmit+0x2724/0x34c0 net/core/dev.c:3584
 dev_queue_xmit+0x17/0x20 net/core/dev.c:3617
 neigh_resolve_output+0x679/0xad0 net/core/neighbour.c:1358
 neigh_output include/net/neighbour.h:482 [inline]
 ip6_finish_output2+0xc9c/0x2810 net/ipv6/ip6_output.c:120
 ip6_finish_output+0x5fe/0xbc0 net/ipv6/ip6_output.c:154
 NF_HOOK_COND include/linux/netfilter.h:277 [inline]
 ip6_output+0x227/0x9b0 net/ipv6/ip6_output.c:171
 dst_output include/net/dst.h:444 [inline]
 NF_HOOK include/linux/netfilter.h:288 [inline]
 ndisc_send_skb+0x100d/0x1570 net/ipv6/ndisc.c:491
 ndisc_send_ns+0x3c1/0x8d0 net/ipv6/ndisc.c:633
 addrconf_dad_work+0xbef/0x1340 net/ipv6/addrconf.c:4033
 process_one_work+0xc1e/0x1b50 kernel/workqueue.c:2145
 worker_thread+0x1cc/0x1440 kernel/workqueue.c:2279
 kthread+0x345/0x410 kernel/kthread.c:240
 ret_from_fork+0x3a/0x50 arch/x86/entry/entry_64.S:412

The buggy address belongs to the page:
page:ffffea00072d8800 count:0 mapcount:-127 mapping:0000000000000000 index:0xffff8801cb620e80
flags: 0x2fffc0000000000()
raw: 02fffc0000000000 0000000000000000 ffff8801cb620e80 00000000ffffff80
raw: ffffea00072e3820 ffffea0007132d20 0000000000000002 0000000000000000
page dumped because: kasan: bad access detected

Memory state around the buggy address:
 ffff8801cb61ff00: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
 ffff8801cb61ff80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>ffff8801cb620000: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
                      ^
 ffff8801cb620080: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
 ffff8801cb620100: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff

Fixes: 2b6867c2ce76 ("net/packet: fix overflow in check for priv area size")
Fixes: dc808110bb62 ("packet: handle too big packets for PACKET_V3")
Fixes: f6fb8f100b80 ("af-packet: TPACKET_V3 flexible buffer implementation.")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

netdev-FAQ: clarify DaveM's position for stable backports

[ Upstream commit 75d4e704fa8d2cf33ff295e5b441317603d7f9fd ]

Per discussion with David at netconf 2018, let's clarify
DaveM's position of handling stable backports in netdev-FAQ.

This is important for people relying on upstream -stable
releases.

Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

kcm: Fix use-after-free caused by clonned sockets

[ Upstream commit eb7f54b90bd8f469834c5e86dcf72ebf9a629811 ]

(resend for properly queueing in patchwork)

kcm_clone() creates kernel socket, which does not take net counter.
Thus, the net may die before the socket is completely destructed,
i.e. kcm_exit_net() is executed before kcm_done().

Reported-by: syzbot+5f1a04e374a635efc426@syzkaller.appspotmail.com
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

isdn: eicon: fix a missing-check bug

[ Upstream commit 6009d1fe6ba3bb2dab55921da60465329cc1cd89 ]

In divasmain.c, the function divas_write() firstly invokes the function
diva_xdi_open_adapter() to open the adapter that matches with the adapter
number provided by the user, and then invokes the function diva_xdi_write()
to perform the write operation using the matched adapter. The two functions
diva_xdi_open_adapter() and diva_xdi_write() are located in diva.c.

In diva_xdi_open_adapter(), the user command is copied to the object 'msg'
from the userspace pointer 'src' through the function pointer 'cp_fn',
which eventually calls copy_from_user() to do the copy. Then, the adapter
number 'msg.adapter' is used to find out a matched adapter from the
'adapter_queue'. A matched adapter will be returned if it is found.
Otherwise, NULL is returned to indicate the failure of the verification on
the adapter number.

As mentioned above, if a matched adapter is returned, the function
diva_xdi_write() is invoked to perform the write operation. In this
function, the user command is copied once again from the userspace pointer
'src', which is the same as the 'src' pointer in diva_xdi_open_adapter() as
both of them are from the 'buf' pointer in divas_write(). Similarly, the
copy is achieved through the function pointer 'cp_fn', which finally calls
copy_from_user(). After the successful copy, the corresponding command
processing handler of the matched adapter is invoked to perform the write
operation.

It is obvious that there are two copies here from userspace, one is in
diva_xdi_open_adapter(), and one is in diva_xdi_write(). Plus, both of
these two copies share the same source userspace pointer, i.e., the 'buf'
pointer in divas_write(). Given that a malicious userspace process can race
to change the content pointed by the 'buf' pointer, this can pose potential
security issues. For example, in the first copy, the user provides a valid
adapter number to pass the verification process and a valid adapter can be
found. Then the user can modify the adapter number to an invalid number.
This way, the user can bypass the verification process of the adapter
number and inject inconsistent data.

This patch reuses the data copied in
diva_xdi_open_adapter() and passes it to diva_xdi_write(). This way, the
above issues can be avoided.

Signed-off-by: Wenwen Wang <wang6495@umn.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ipv4: remove warning in ip_recv_error

[ Upstream commit 730c54d59403658a62af6517338fa8d4922c1b28 ]

A precondition check in ip_recv_error triggered on an otherwise benign
race. Remove the warning.

The warning triggers when passing an ipv6 socket to this ipv4 error
handling function. RaceFuzzer was able to trigger it due to a race
in setsockopt IPV6_ADDRFORM.

  ---
  CPU0
    do_ipv6_setsockopt
      sk->sk_socket->ops = &inet_dgram_ops;

  ---
  CPU1
    sk->sk_prot->recvmsg
      udp_recvmsg
        ip_recv_error
          WARN_ON_ONCE(sk->sk_family == AF_INET6);

  ---
  CPU0
    do_ipv6_setsockopt
      sk->sk_family = PF_INET;

This socket option converts a v6 socket that is connected to a v4 peer
to an v4 socket. It updates the socket on the fly, changing fields in
sk as well as other structs. This is inherently non-atomic. It races
with the lockless udp_recvmsg path.

No other code makes an assumption that these fields are updated
atomically. It is benign here, too, as ip_recv_error cares only about
the protocol of the skbs enqueued on the error queue, for which
sk_family is not a precise predictor (thanks to another isue with
IPV6_ADDRFORM).

Link: http://lkml.kernel.org/r/20180518120826.GA19515@dragonet.kaist.ac.kr
Fixes: 7ce875e5ecb8 ("ipv4: warn once on passing AF_INET6 socket to ip_recv_error")
Reported-by: DaeRyong Jeong <threeearcat@gmail.com>
Suggested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ip6mr: only set ip6mr_table from setsockopt when ip6mr_new_table succeeds

[ Upstream commit 848235edb5c93ed086700584c8ff64f6d7fc778d ]

Currently, raw6_sk(sk)->ip6mr_table is set unconditionally during
ip6_mroute_setsockopt(MRT6_TABLE). A subsequent attempt at the same
setsockopt will fail with -ENOENT, since we haven't actually created
that table.

A similar fix for ipv4 was included in commit 5e1859fbcc3c ("ipv4: ipmr:
various fixes and cleanups").

Fixes: d1db275dd3f6 ("ipv6: ip6mr: support multiple tables")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

enic: set DMA mask to 47 bit

[ Upstream commit 322eaa06d55ebc1402a4a8d140945cff536638b4 ]

In commit 624dbf55a359b ("driver/net: enic: Try DMA 64 first, then
failover to DMA") DMA mask was changed from 40 bits to 64 bits.
Hardware actually supports only 47 bits.

Fixes: 624dbf55a359b ("driver/net: enic: Try DMA 64 first, then failover to DMA")
Signed-off-by: Govindarajulu Varadarajan <gvaradar@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dccp: don't free ccid2_hc_tx_sock struct in dccp_disconnect()

[ Upstream commit 2677d20677314101293e6da0094ede7b5526d2b1 ]

Syzbot reported the use-after-free in timer_is_static_object() [1].

This can happen because the structure for the rto timer (ccid2_hc_tx_sock)
is removed in dccp_disconnect(), and ccid2_hc_tx_rto_expire() can be
called after that.

The report [1] is similar to the one in commit 120e9dabaf55 ("dccp:
defer ccid_hc_tx_delete() at dismantle time"). And the fix is the same,
delay freeing ccid2_hc_tx_sock structure, so that it is freed in
dccp_sk_destruct().

[1]

==================================================================
BUG: KASAN: use-after-free in timer_is_static_object+0x80/0x90
kernel/time/timer.c:607
Read of size 8 at addr ffff8801bebb5118 by task syz-executor2/25299

CPU: 1 PID: 25299 Comm: syz-executor2 Not tainted 4.17.0-rc5+ #54
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS
Google 01/01/2011
Call Trace:
  <IRQ>
  __dump_stack lib/dump_stack.c:77 [inline]
  dump_stack+0x1b9/0x294 lib/dump_stack.c:113
  print_address_description+0x6c/0x20b mm/kasan/report.c:256
  kasan_report_error mm/kasan/report.c:354 [inline]
  kasan_report.cold.7+0x242/0x2fe mm/kasan/report.c:412
  __asan_report_load8_noabort+0x14/0x20 mm/kasan/report.c:433
  timer_is_static_object+0x80/0x90 kernel/time/timer.c:607
  debug_object_activate+0x2d9/0x670 lib/debugobjects.c:508
  debug_timer_activate kernel/time/timer.c:709 [inline]
  debug_activate kernel/time/timer.c:764 [inline]
  __mod_timer kernel/time/timer.c:1041 [inline]
  mod_timer+0x4d3/0x13b0 kernel/time/timer.c:1102
  sk_reset_timer+0x22/0x60 net/core/sock.c:2742
  ccid2_hc_tx_rto_expire+0x587/0x680 net/dccp/ccids/ccid2.c:147
  call_timer_fn+0x230/0x940 kernel/time/timer.c:1326
  expire_timers kernel/time/timer.c:1363 [inline]
  __run_timers+0x79e/0xc50 kernel/time/timer.c:1666
  run_timer_softirq+0x4c/0x70 kernel/time/timer.c:1692
  __do_softirq+0x2e0/0xaf5 kernel/softirq.c:285
  invoke_softirq kernel/softirq.c:365 [inline]
  irq_exit+0x1d1/0x200 kernel/softirq.c:405
  exiting_irq arch/x86/include/asm/apic.h:525 [inline]
  smp_apic_timer_interrupt+0x17e/0x710 arch/x86/kernel/apic/apic.c:1052
  apic_timer_interrupt+0xf/0x20 arch/x86/entry/entry_64.S:863
  </IRQ>
...
Allocated by task 25374:
  save_stack+0x43/0xd0 mm/kasan/kasan.c:448
  set_track mm/kasan/kasan.c:460 [inline]
  kasan_kmalloc+0xc4/0xe0 mm/kasan/kasan.c:553
  kasan_slab_alloc+0x12/0x20 mm/kasan/kasan.c:490
  kmem_cache_alloc+0x12e/0x760 mm/slab.c:3554
  ccid_new+0x25b/0x3e0 net/dccp/ccid.c:151
  dccp_hdlr_ccid+0x27/0x150 net/dccp/feat.c:44
  __dccp_feat_activate+0x184/0x270 net/dccp/feat.c:344
  dccp_feat_activate_values+0x3a7/0x819 net/dccp/feat.c:1538
  dccp_create_openreq_child+0x472/0x610 net/dccp/minisocks.c:128
  dccp_v4_request_recv_sock+0x12c/0xca0 net/dccp/ipv4.c:408
  dccp_v6_request_recv_sock+0x125d/0x1f10 net/dccp/ipv6.c:415
  dccp_check_req+0x455/0x6a0 net/dccp/minisocks.c:197
  dccp_v4_rcv+0x7b8/0x1f3f net/dccp/ipv4.c:841
  ip_local_deliver_finish+0x2e3/0xd80 net/ipv4/ip_input.c:215
  NF_HOOK include/linux/netfilter.h:288 [inline]
  ip_local_deliver+0x1e1/0x720 net/ipv4/ip_input.c:256
  dst_input include/net/dst.h:450 [inline]
  ip_rcv_finish+0x81b/0x2200 net/ipv4/ip_input.c:396
  NF_HOOK include/linux/netfilter.h:288 [inline]
  ip_rcv+0xb70/0x143d net/ipv4/ip_input.c:492
  __netif_receive_skb_core+0x26f5/0x3630 net/core/dev.c:4592
  __netif_receive_skb+0x2c/0x1e0 net/core/dev.c:4657
  process_backlog+0x219/0x760 net/core/dev.c:5337
  napi_poll net/core/dev.c:5735 [inline]
  net_rx_action+0x7b7/0x1930 net/core/dev.c:5801
  __do_softirq+0x2e0/0xaf5 kernel/softirq.c:285

Freed by task 25374:
  save_stack+0x43/0xd0 mm/kasan/kasan.c:448
  set_track mm/kasan/kasan.c:460 [inline]
  __kasan_slab_free+0x11a/0x170 mm/kasan/kasan.c:521
  kasan_slab_free+0xe/0x10 mm/kasan/kasan.c:528
  __cache_free mm/slab.c:3498 [inline]
  kmem_cache_free+0x86/0x2d0 mm/slab.c:3756
  ccid_hc_tx_delete+0xc3/0x100 net/dccp/ccid.c:190
  dccp_disconnect+0x130/0xc66 net/dccp/proto.c:286
  dccp_close+0x3bc/0xe60 net/dccp/proto.c:1045
  inet_release+0x104/0x1f0 net/ipv4/af_inet.c:427
  inet6_release+0x50/0x70 net/ipv6/af_inet6.c:460
  sock_release+0x96/0x1b0 net/socket.c:594
  sock_close+0x16/0x20 net/socket.c:1149
  __fput+0x34d/0x890 fs/file_table.c:209
  ____fput+0x15/0x20 fs/file_table.c:243
  task_work_run+0x1e4/0x290 kernel/task_work.c:113
  tracehook_notify_resume include/linux/tracehook.h:191 [inline]
  exit_to_usermode_loop+0x2bd/0x310 arch/x86/entry/common.c:166
  prepare_exit_to_usermode arch/x86/entry/common.c:196 [inline]
  syscall_return_slowpath arch/x86/entry/common.c:265 [inline]
  do_syscall_64+0x6ac/0x800 arch/x86/entry/common.c:290
  entry_SYSCALL_64_after_hwframe+0x49/0xbe

The buggy address belongs to the object at ffff8801bebb4cc0
  which belongs to the cache ccid2_hc_tx_sock of size 1240
The buggy address is located 1112 bytes inside of
  1240-byte region [ffff8801bebb4cc0, ffff8801bebb5198)
The buggy address belongs to the page:
page:ffffea0006faed00 count:1 mapcount:0 mapping:ffff8801bebb41c0
index:0xffff8801bebb5240 compound_mapcount: 0
flags: 0x2fffc0000008100(slab|head)
raw: 02fffc0000008100 ffff8801bebb41c0 ffff8801bebb5240 0000000100000003
raw: ffff8801cdba3138 ffffea0007634120 ffff8801cdbaab40 0000000000000000
page dumped because: kasan: bad access detected
...
==================================================================

Reported-by: syzbot+5d47e9ec91a6f15dbd6f@syzkaller.appspotmail.com
Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

bnx2x: use the right constant

[ Upstream commit dd612f18a49b63af8b3a5f572d999bdb197385bc ]

Nearby code that also tests port suggests that the P0 constant should be
used when port is zero.

The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@@
expression e,e1;
@@

* e ? e1 : e1
// </smpl>

Fixes: 6c3218c6f7e5 ("bnx2x: Adjust ETS to 578xx")
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm: set FMODE_UNSIGNED_OFFSET for drm files

commit 76ef6b28ea4f81c3d511866a9b31392caa833126 upstream.

Since we have the ttm and gem vma managers using a subset
of the file address space for objects, and these start at
0x100000000 they will overflow the new mmap checks.

I've checked all the mmap routines I could see for any
bad behaviour but overall most people use GEM/TTM VMA
managers even the legacy drivers have a hashtable.

Reported-and-Tested-by: Arthur Marsh (amarsh04 on #radeon)
Fixes: be83bbf8068 (mmap: introduce sane default mmap limits)
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

kconfig: Avoid format overflow warning from GCC 8.1

commit 2ae89c7a82ea9d81a19b4fc2df23bef4b112f24e upstream.

In file included from scripts/kconfig/zconf.tab.c:2485:
scripts/kconfig/confdata.c: In function ‘conf_write’:
scripts/kconfig/confdata.c:773:22: warning: ‘%s’ directive writing likely 7 or more bytes into a region of size between 1 and 4097 [-Wformat-overflow=]
  sprintf(newname, "%s%s", dirname, basename);
                      ^~
scripts/kconfig/confdata.c:773:19: note: assuming directive output of 7 bytes
  sprintf(newname, "%s%s", dirname, basename);
                   ^~~~~~
scripts/kconfig/confdata.c:773:2: note: ‘sprintf’ output 1 or more bytes (assuming 4104) into a destination of size 4097
  sprintf(newname, "%s%s", dirname, basename);
  ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
scripts/kconfig/confdata.c:776:23: warning: ‘.tmpconfig.’ directive writing 11 bytes into a region of size between 1 and 4097 [-Wformat-overflow=]
   sprintf(tmpname, "%s.tmpconfig.%d", dirname, (int)getpid());
                       ^~~~~~~~~~~
scripts/kconfig/confdata.c:776:3: note: ‘sprintf’ output between 13 and 4119 bytes into a destination of size 4097
   sprintf(tmpname, "%s.tmpconfig.%d", dirname, (int)getpid());
   ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

Increase the size of tmpname and newname to make GCC happy.

Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

btrfs: define SUPER_FLAG_METADUMP_V2

commit e2731e55884f2138a252b0a3d7b24d57e49c3c59 upstream.

btrfs-progs uses super flag bit BTRFS_SUPER_FLAG_METADUMP_V2 (1ULL << 34).
So just define that in kernel so that we know its been used.

Signed-off-by: Anand Jain <anand.jain@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mmap: relax file size limit for regular files

commit 423913ad4ae5b3e8fb8983f70969fb522261ba26 upstream.

Commit be83bbf80682 ("mmap: introduce sane default mmap limits") was
introduced to catch problems in various ad-hoc character device drivers
doing mmap and getting the size limits wrong.  In the process, it used
"known good" limits for the normal cases of mapping regular files and
block device drivers.

It turns out that the "s_maxbytes" limit was less "known good" than I
thought.  In particular, /proc doesn't set it, but exposes one regular
file to mmap: /proc/vmcore.  As a result, that file got limited to the
default MAX_INT s_maxbytes value.

This went unnoticed for a while, because apparently the only thing that
needs it is the s390 kernel zfcpdump, but there might be other tools
that use this too.

Vasily suggested just changing s_maxbytes for all of /proc, which isn't
wrong, but makes me nervous at this stage.  So instead, just make the
new mmap limit always be MAX_LFS_FILESIZE for regular files, which won't
affect anything else.  It wasn't the regular file case I was worried
about.

I'd really prefer for maxsize to have been per-inode, but that is not
how things are today.

Fixes: be83bbf80682 ("mmap: introduce sane default mmap limits")
Reported-by: Vasily Gorbik <gor@linux.ibm.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mmap: introduce sane default mmap limits

commit be83bbf806822b1b89e0a0f23cd87cddc409e429 upstream.

The internal VM "mmap()" interfaces are based on the mmap target doing
everything using page indexes rather than byte offsets, because
traditionally (ie 32-bit) we had the situation that the byte offset
didn't fit in a register.  So while the mmap virtual address was limited
by the word size of the architecture, the backing store was not.

So we're basically passing "pgoff" around as a page index, in order to
be able to describe backing store locations that are much bigger than
the word size (think files larger than 4GB etc).

But while this all makes a ton of sense conceptually, we've been dogged
by various drivers that don't really understand this, and internally
work with byte offsets, and then try to work with the page index by
turning it into a byte offset with "pgoff << PAGE_SHIFT".

Which obviously can overflow.

Adding the size of the mapping to it to get the byte offset of the end
of the backing store just exacerbates the problem, and if you then use
this overflow-prone value to check various limits of your device driver
mmap capability, you're just setting yourself up for problems.

The correct thing for drivers to do is to do their limit math in page
indices, the way the interface is designed.  Because the generic mmap
code _does_ test that the index doesn't overflow, since that's what the
mmap code really cares about.

HOWEVER.

Finding and fixing various random drivers is a sisyphean task, so let's
just see if we can just make the core mmap() code do the limiting for
us.  Realistically, the only "big" backing stores we need to care about
are regular files and block devices, both of which are known to do this
properly, and which have nice well-defined limits for how much data they
can access.

So let's special-case just those two known cases, and then limit other
random mmap users to a backing store that still fits in "unsigned long".
Realistically, that's not much of a limit at all on 64-bit, and on
32-bit architectures the only worry might be the GPU drivers, which can
have big physical address spaces.

To make it possible for drivers like that to say that they are 64-bit
clean, this patch does repurpose the "FMODE_UNSIGNED_OFFSET" bit in the
file flags to allow drivers to mark their file descriptors as safe in
the full 64-bit mmap address space.

[ The timing for doing this is less than optimal, and this should really
  go in a merge window. But realistically, this needs wide testing more
  than it needs anything else, and being main-line is the only way to do
  that.

  So the earlier the better, even if it's outside the proper development
  cycle        - Linus ]

Cc: Kees Cook <keescook@chromium.org>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Willy Tarreau <w@1wt.eu>
Cc: Dave Airlie <airlied@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tpm: self test failure should not cause suspend to fail

commit 0803d7befa15cab5717d667a97a66214d2a4c083 upstream.

The Acer Acer Veriton X4110G has a TPM device detected as:
  tpm_tis 00:0b: 1.2 TPM (device-id 0xFE, rev-id 71)

After the first S3 suspend, the following error appears during resume:
  tpm tpm0: A TPM error(38) occurred continue selftest

Any following S3 suspend attempts will now fail with this error:
  tpm tpm0: Error (38) sending savestate before suspend
  PM: Device 00:0b failed to suspend: error 38

Error 38 is TPM_ERR_INVALID_POSTINIT which means the TPM is
not in the correct state. This indicates that the platform BIOS
is not sending the usual TPM_Startup command during S3 resume.
>From this point onwards, all TPM commands will fail.

The same issue was previously reported on Foxconn 6150BK8MC and
Sony Vaio TX3.

The platform behaviour seems broken here, but we should not break
suspend/resume because of this.

When the unexpected TPM state is encountered, set a flag to skip the
affected TPM_SaveState command on later suspends.

Cc: stable@vger.kernel.org
Signed-off-by: Chris Chiu <chiu@endlessm.com>
Signed-off-by: Daniel Drake <drake@endlessm.com>
Link: http://lkml.kernel.org/r/CAB4CAwfSCvj1cudi+MWaB5g2Z67d9DwY1o475YOZD64ma23UiQ@mail.gmail.com
Link: https://lkml.org/lkml/2011/3/28/192
Link: https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=591031
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tpm: do not suspend/resume if power stays on

commit b5d0ebc99bf5d0801a5ecbe958caa3d68b8eaee8 upstream.

The suspend/resume behavior of the TPM can be controlled by setting
"powered-while-suspended" in the DTS. This is useful for the cases
when hardware does not power-off the TPM.

Signed-off-by: Sonny Rao <sonnyrao@chromium.org>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: James Morris <james.l.morris@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Linux 4.9.107

serial: pl011: add console matching function

commit 10879ae5f12e9cab3c4e8e9504c1aaa8a033bde7 upstream.

This patch adds function pl011_console_match() that implements
method match of struct console.  It allows to match consoles against
data specified in a string, for example taken from command line or
compiled by ACPI SPCR table handler.

This patch was merged to tty-next but then reverted because of
conflict with

commit 46e36683f433 ("serial: earlycon: Extend earlycon command line option to support 64-bit addresses")

Now it is fixed.

Signed-off-by: Aleksey Makarov <aleksey.makarov@linaro.org>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Tested-by: Christopher Covington <cov@codeaurora.org>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

sparc64: Don't clibber fixed registers in __multi4.

commit 79db795833bf5c3e798bcd7a5aeeee3fb0505927 upstream.

%g4 and %g5 are fixed registers used by the kernel for the thread
pointer and the per-cpu offset.  Use %o4 and %g7 instead.

Diagnosis by Anthony Yznaga.

Fixes: 1b4af13ff2cc ("sparc64: Add __multi3 for gcc 7.x and later.")
Reported-by: Anatoly Pugachev <matorola@gmail.com>
Tested-by: Anatoly Pugachev <matorola@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mm: fix the NULL mapping case in __isolate_lru_page()

commit 145e1a71e090575c74969e3daa8136d1e5b99fc8 upstream.

George Boole would have noticed a slight error in 4.16 commit
69d763fc6d3a ("mm: pin address_space before dereferencing it while
isolating an LRU page").  Fix it, to match both the comment above it,
and the original behaviour.

Although anonymous pages are not marked PageDirty at first, we have an
old habit of calling SetPageDirty when a page is removed from swap
cache: so there's a category of ex-swap pages that are easily
migratable, but were inadvertently excluded from compaction's async
migration in 4.16.

Link: http://lkml.kernel.org/r/alpine.LSU.2.11.1805302014001.12558@eggly.anvils
Fixes: 69d763fc6d3a ("mm: pin address_space before dereferencing it while isolating an LRU page")
Signed-off-by: Hugh Dickins <hughd@google.com>
Acked-by: Minchan Kim <minchan@kernel.org>
Acked-by: Mel Gorman <mgorman@techsingularity.net>
Reported-by: Ivan Kalvachev <ikalvachev@gmail.com>
Cc: "Huang, Ying" <ying.huang@intel.com>
Cc: Jan Kara <jack@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

fix io_destroy()/aio_complete() race

commit 4faa99965e027cc057c5145ce45fa772caa04e8d upstream.

If io_destroy() gets to cancelling everything that can be cancelled and
gets to kiocb_cancel() calling the function driver has left in ->ki_cancel,
it becomes vulnerable to a race with IO completion.  At that point req
is already taken off the list and aio_complete() does *NOT* spin until
we (in free_ioctx_users()) releases ->ctx_lock.  As the result, it proceeds
to kiocb_free(), freing req just it gets passed to ->ki_cancel().

Fix is simple - remove from the list after the call of kiocb_cancel().  All
instances of ->ki_cancel() already have to cope with the being called with
iocb still on list - that's what happens in io_cancel(2).

Cc: stable@kernel.org
Fixes: 0460fef2a921 "aio: use cancellation list lazily"
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

sparc64: Fix build warnings with gcc 7.

commit 0fde7ad71ee371ede73b3f326e58f9e8d102feb6 upstream.

arch/sparc/kernel/ds.c: In function ‘register_services’:
arch/sparc/kernel/ds.c:912:3: error: ‘strcpy’: writing at least 1 byte
into a region of size 0 overflows the destination

Reported-by: Anatoly Pugachev <matorola@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/i915: Disable LVDS on Radiant P845

commit b3fb22733ae61050f8d10a1d6a8af176c5c5db1a upstream.

Radiant P845 does not have LVDS, only VGA.

Cc: stable@vger.kernel.org
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=105468
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180309222204.4771-1-linux@rainbow-software.org
(cherry picked from commit 7f7105f99b75aca4f8c2a748ed6b82c7f8be3293)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/psr: Fix missed entry in PSR setup time table.

commit bdcc02cf1bb508fc700df7662f55058f651f2621 upstream.

Entry corresponding to 220 us setup time was missing. I am not aware of
any specific bug this fixes, but this could potentially result in enabling
PSR on a panel with a higher setup time requirement than supported by the
hardware.

I verified the value is present in eDP spec versions 1.3, 1.4 and 1.4a.

Fixes: 6608804b3d7f ("drm/dp: Add drm_dp_psr_setup_time()")
Cc: stable@vger.kernel.org
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Jose Roberto de Souza <jose.souza@intel.com>
Cc: dri-devel@lists.freedesktop.org
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Tarun Vyas <tarun.vyas@intel.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180511195145.3829-3-dhinakaran.pandiyan@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

IB/core: Fix error code for invalid GID entry

commit a840c93ca7582bb6c88df2345a33f979b7a67874 upstream.

When a GID entry is invalid EAGAIN is returned. This is an incorrect error
code, there is nothing that will make this GID entry valid again in
bounded time.

Some user space tools fail incorrectly if EAGAIN is returned here, and
this represents a small ABI change from earlier kernels.

The first patch in the Fixes list makes entries that were valid before
to become invalid, allowing this code to trigger, while the second patch
in the Fixes list introduced the wrong EAGAIN.

Therefore revert the return result to EINVAL which matches the historical
expectations of the ibv_query_gid_type() API of the libibverbs user space
library.

Cc: <stable@vger.kernel.org>
Fixes: 598ff6bae689 ("IB/core: Refactor GID modify code for RoCE")
Fixes: 03db3a2d81e6 ("IB/core: Add RoCE GID table management")
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

hwtracing: stm: fix build error on some arches

commit 806e30873f0e74d9d41b0ef761bd4d3e55c7d510 upstream.

Commit b5e2ced9bf81 ("stm class: Use vmalloc for the master map") caused
a build error on some arches as vmalloc.h was not explicitly included.

Fix that by adding it to the list of includes.

Fixes: b5e2ced9bf81 ("stm class: Use vmalloc for the master map")
Reported-by: kbuild test robot <lkp@intel.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

stm class: Use vmalloc for the master map

commit b5e2ced9bf81393034072dd4d372f6b430bc1f0a upstream.

Fengguang is running into a warning from the buddy allocator:

> swapper/0: page allocation failure: order:9, mode:0x14040c0(GFP_KERNEL|__GFP_COMP), nodemask=(null)
> CPU: 1 PID: 1 Comm: swapper/0 Not tainted 4.17.0-rc1 #262
> Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1 04/01/2014
> Call Trace:
...
>  __kmalloc+0x14b/0x180: ____cache_alloc at mm/slab.c:3127
>  stm_register_device+0xf3/0x5c0: stm_register_device at drivers/hwtracing/stm/core.c:695
...

Which is basically a result of the stm class trying to allocate ~512kB
for the dummy_stm with its default parameters. There's no reason, however,
for it not to be vmalloc()ed instead, which is what this patch does.

Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
CC: stable@vger.kernel.org # v4.4+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

scsi: scsi_transport_srp: Fix shost to rport translation

commit c9ddf73476ff4fffb7a87bd5107a0705bf2cf64b upstream.

Since an SRP remote port is attached as a child to shost->shost_gendev
and as the only child, the translation from the shost pointer into an
rport pointer must happen by looking up the shost child that is an
rport. This patch fixes the following KASAN complaint:

BUG: KASAN: slab-out-of-bounds in srp_timed_out+0x57/0x110 [scsi_transport_srp]
Read of size 4 at addr ffff880035d3fcc0 by task kworker/1:0H/19

CPU: 1 PID: 19 Comm: kworker/1:0H Not tainted 4.16.0-rc3-dbg+ #1
Workqueue: kblockd blk_mq_timeout_work
Call Trace:
dump_stack+0x85/0xc7
print_address_description+0x65/0x270
kasan_report+0x231/0x350
srp_timed_out+0x57/0x110 [scsi_transport_srp]
scsi_times_out+0xc7/0x3f0 [scsi_mod]
blk_mq_terminate_expired+0xc2/0x140
bt_iter+0xbc/0xd0
blk_mq_queue_tag_busy_iter+0x1c7/0x350
blk_mq_timeout_work+0x325/0x3f0
process_one_work+0x441/0xa50
worker_thread+0x76/0x6c0
kthread+0x1b2/0x1d0
ret_from_fork+0x24/0x30

Fixes: e68ca75200fe ("scsi_transport_srp: Reduce failover time")
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Cc: Jason Gunthorpe <jgg@mellanox.com>
Cc: Doug Ledford <dledford@redhat.com>
Cc: Laurence Oberman <loberman@redhat.com>
Cc: stable@vger.kernel.org
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

MIPS: prctl: Disallow FRE without FR with PR_SET_FP_MODE requests

commit 28e4213dd331e944e7fca1954a946829162ed9d4 upstream.

Having PR_FP_MODE_FRE (i.e. Config5.FRE) set without PR_FP_MODE_FR (i.e.
Status.FR) is not supported as the lone purpose of Config5.FRE is to
emulate Status.FR=0 handling on FPU hardware that has Status.FR=1
hardwired[1][2].  Also we do not handle this case elsewhere, and assume
throughout our code that TIF_HYBRID_FPREGS and TIF_32BIT_FPREGS cannot
be set both at once for a task, leading to inconsistent behaviour if
this does happen.

Return unsuccessfully then from prctl(2) PR_SET_FP_MODE calls requesting
PR_FP_MODE_FRE to be set with PR_FP_MODE_FR clear.  This corresponds to
modes allowed by `mips_set_personality_fp'.

References:

[1] "MIPS Architecture For Programmers, Vol. III: MIPS32 / microMIPS32
    Privileged Resource Architecture", Imagination Technologies,
    Document Number: MD00090, Revision 6.02, July 10, 2015, Table 9.69
    "Config5 Register Field Descriptions", p. 262

[2] "MIPS Architecture For Programmers, Volume III: MIPS64 / microMIPS64
    Privileged Resource Architecture", Imagination Technologies,
    Document Number: MD00091, Revision 6.03, December 22, 2015, Table
    9.72 "Config5 Register Field Descriptions", p. 288

Fixes: 9791554b45a2 ("MIPS,prctl: add PR_[GS]ET_FP_MODE prctl options for MIPS")
Signed-off-by: Maciej W. Rozycki <macro@mips.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: <stable@vger.kernel.org> # 4.0+
Patchwork: https://patchwork.linux-mips.org/patch/19327/
Signed-off-by: James Hogan <jhogan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

MIPS: ptrace: Fix PTRACE_PEEKUSR requests for 64-bit FGRs

commit c7e814628df65f424fe197dde73bfc67e4a244d7 upstream.

Use 64-bit accesses for 64-bit floating-point general registers with
PTRACE_PEEKUSR, removing the truncation of their upper halves in the
FR=1 mode, caused by commit bbd426f542cb ("MIPS: Simplify FP context
access"), which inadvertently switched them to using 32-bit accesses.

The PTRACE_POKEUSR side is fine as it's never been broken and continues
using 64-bit accesses.

Fixes: bbd426f542cb ("MIPS: Simplify FP context access")
Signed-off-by: Maciej W. Rozycki <macro@mips.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: <stable@vger.kernel.org> # 3.15+
Patchwork: https://patchwork.linux-mips.org/patch/19334/
Signed-off-by: James Hogan <jhogan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iio:kfifo_buf: check for uint overflow

commit 3d13de4b027d5f6276c0f9d3a264f518747d83f2 upstream.

Currently, the following causes a kernel OOPS in memcpy:

echo 1073741825 > buffer/length
echo 1 > buffer/enable

Note that using 1073741824 instead of 1073741825 causes "write error:
Cannot allocate memory" but no OOPS.

This is because 1073741824 == 2^30 and 1073741825 == 2^30+1. Since kfifo
rounds up to the nearest power of 2, it will actually call kmalloc with
roundup_pow_of_two(length) * bytes_per_datum.

Using length == 1073741825 and bytes_per_datum == 2, we get:

kmalloc(roundup_pow_of_two(1073741825) * 2
or kmalloc(2147483648 * 2)
or kmalloc(4294967296)
or kmalloc(UINT_MAX + 1)

so this overflows to 0, causing kmalloc to return ZERO_SIZE_PTR and
subsequent memcpy to fail once the device is enabled.

Fix this by checking for overflow prior to allocating a kfifo. With this
check added, the above code returns -EINVAL when enabling the buffer,
rather than causing an OOPS.

Signed-off-by: Martin Kelly <mkelly@xevo.com>
cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net/mlx4_en: fix potential use-after-free with dma_unmap_page

[ Not relevant upstream, therefore no upstream commit. ]

To fix, unmap the page as soon as possible.

When swiotlb is in use, calling dma_unmap_page means that
the original page mapped with dma_map_page must still be valid,
as swiotlb will copy data from its internal cache back to the
originally requested DMA location.

When GRO is enabled, before this patch all references to the
original frag may be put and the page freed before dma_unmap_page
in mlx4_en_free_frag is called.

It is possible there is a path where the use-after-free occurs
even with GRO disabled, but this has not been observed so far.

The bug can be trivially detected by doing the following:

* Compile the kernel with DEBUG_PAGEALLOC
* Run the kernel as a Xen Dom0
* Leave GRO enabled on the interface
* Run a 10 second or more test with iperf over the interface.

This bug was likely introduced in
commit 4cce66cdd14a ("mlx4_en: map entire pages to increase throughput"),
first part of u3.6.

It was incidentally fixed in
commit 34db548bfb95 ("mlx4: add page recycling in receive path"),
first part of v4.12.

This version applies to the v4.9 series.

Signed-off-by: Sarah Newman <srn@prgmr.com>
Tested-by: Sarah Newman <srn@prgmr.com>
Cc: Tariq Toukan <tariqt@mellanox.com>
Cc: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

powerpc/64s: Add support for a store forwarding barrier at kernel entry/exit

commit a048a07d7f4535baa4cbad6bc024f175317ab938 upstream.

On some CPUs we can prevent a vulnerability related to store-to-load
forwarding by preventing store forwarding between privilege domains,
by inserting a barrier in kernel entry and exit paths.

This is known to be the case on at least Power7, Power8 and Power9
powerpc CPUs.

Barriers must be inserted generally before the first load after moving
to a higher privilege, and after the last store before moving to a
lower privilege, HV and PR privilege transitions must be protected.

Barriers are added as patch sections, with all kernel/hypervisor entry
points patched, and the exit points to lower privilge levels patched
similarly to the RFI flush patching.

Firmware advertisement is not implemented yet, so CPU flush types
are hard coded.

Thanks to Michal Suchánek for bug fixes and review.

Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Mauricio Faria de Oliveira <mauricfo@linux.vnet.ibm.com>
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michal Suchánek <msuchanek@suse.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

powerpc/64s: Fix section mismatch warnings from setup_rfi_flush()

commit 501a78cbc17c329fabf8e9750a1e9ab810c88a0e upstream.

The recent LPM changes to setup_rfi_flush() are causing some section
mismatch warnings because we removed the __init annotation on
setup_rfi_flush():

  The function setup_rfi_flush() references
  the function __init ppc64_bolted_size().
  the function __init memblock_alloc_base().

The references are actually in init_fallback_flush(), but that is
inlined into setup_rfi_flush().

These references are safe because:
 - only pseries calls setup_rfi_flush() at runtime
 - pseries always passes L1D_FLUSH_FALLBACK at boot
 - so the fallback flush area will always be allocated
 - so the check in init_fallback_flush() will always return early:
   /* Only allocate the fallback flush area once (at boot time). */
   if (l1d_flush_fallback_area)
    return;

 - and therefore we won't actually call the freed init routines.

We should rework the code to make it safer by default rather than
relying on the above, but for now as a quick-fix just add a __ref
annotation to squash the warning.

Fixes: abf110f3e1ce ("powerpc/rfi-flush: Make it possible to call setup_rfi_flush() again")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

powerpc/pseries: Restore default security feature flags on setup

commit 6232774f1599028a15418179d17f7df47ede770a upstream.

After migration the security feature flags might have changed (e.g.,
destination system with unpatched firmware), but some flags are not
set/clear again in init_cpu_char_feature_flags() because it assumes
the security flags to be the defaults.

Additionally, if the H_GET_CPU_CHARACTERISTICS hypercall fails then
init_cpu_char_feature_flags() does not run again, which potentially
might leave the system in an insecure or sub-optimal configuration.

So, just restore the security feature flags to the defaults assumed
by init_cpu_char_feature_flags() so it can set/clear them correctly,
and to ensure safe settings are in place in case the hypercall fail.

Fixes: f636c14790ea ("powerpc/pseries: Set or clear security feature flags")
Depends-on: 19887d6a28e2 ("powerpc: Move default security feature flags")
Signed-off-by: Mauricio Faria de Oliveira <mauricfo@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

powerpc: Move default security feature flags

commit e7347a86830f38dc3e40c8f7e28c04412b12a2e7 upstream.

This moves the definition of the default security feature flags
(i.e., enabled by default) closer to the security feature flags.

This can be used to restore current flags to the default flags.

Signed-off-by: Mauricio Faria de Oliveira <mauricfo@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

powerpc/pseries: Fix clearing of security feature flags

commit 0f9bdfe3c77091e8704d2e510eb7c2c2c6cde524 upstream.

The H_CPU_BEHAV_* flags should be checked for in the 'behaviour' field
of 'struct h_cpu_char_result' -- 'character' is for H_CPU_CHAR_*
flags.

Found by playing around with QEMU's implementation of the hypercall:

  H_CPU_CHAR=0xf000000000000000
  H_CPU_BEHAV=0x0000000000000000

  This clears H_CPU_BEHAV_FAVOUR_SECURITY and H_CPU_BEHAV_L1D_FLUSH_PR
  so pseries_setup_rfi_flush() disables 'rfi_flush'; and it also
  clears H_CPU_CHAR_L1D_THREAD_PRIV flag. So there is no RFI flush
  mitigation at all for cpu_show_meltdown() to report; but currently
  it does:

  Original kernel:

    # cat /sys/devices/system/cpu/vulnerabilities/meltdown
    Mitigation: RFI Flush

  Patched kernel:

    # cat /sys/devices/system/cpu/vulnerabilities/meltdown
    Not affected

  H_CPU_CHAR=0x0000000000000000
  H_CPU_BEHAV=0xf000000000000000

  This sets H_CPU_BEHAV_BNDS_CHK_SPEC_BAR so cpu_show_spectre_v1() should
  report vulnerable; but currently it doesn't:

  Original kernel:

    # cat /sys/devices/system/cpu/vulnerabilities/spectre_v1
    Not affected

  Patched kernel:

    # cat /sys/devices/system/cpu/vulnerabilities/spectre_v1
    Vulnerable

Brown-paper-bag-by: Michael Ellerman <mpe@ellerman.id.au>
Fixes: f636c14790ea ("powerpc/pseries: Set or clear security feature flags")
Signed-off-by: Mauricio Faria de Oliveira <mauricfo@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

powerpc/64s: Wire up cpu_show_spectre_v2()

commit d6fbe1c55c55c6937cbea3531af7da84ab7473c3 upstream.

Add a definition for cpu_show_spectre_v2() to override the generic
version. This has several permuations, though in practice some may not
occur we cater for any combination.

The most verbose is:

  Mitigation: Indirect branch serialisation (kernel only), Indirect
  branch cache disabled, ori31 speculation barrier enabled

We don't treat the ori31 speculation barrier as a mitigation on its
own, because it has to be *used* by code in order to be a mitigation
and we don't know if userspace is doing that. So if that's all we see
we say:

  Vulnerable, ori31 speculation barrier enabled

Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

powerpc/64s: Wire up cpu_show_spectre_v1()

commit 56986016cb8cd9050e601831fe89f332b4e3c46e upstream.

Add a definition for cpu_show_spectre_v1() to override the generic
version. Currently this just prints "Not affected" or "Vulnerable"
based on the firmware flag.

Although the kernel does have array_index_nospec() in a few places, we
haven't yet audited all the powerpc code to see where it's necessary,
so for now we don't list that as a mitigation.

Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

powerpc/pseries: Use the security flags in pseries_setup_rfi_flush()

commit 2e4a16161fcd324b1f9bf6cb6856529f7eaf0689 upstream.

Now that we have the security flags we can simplify the code in
pseries_setup_rfi_flush() because the security flags have pessimistic
defaults.

Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

powerpc/powernv: Use the security flags in pnv_setup_rfi_flush()

commit 37c0bdd00d3ae83369ab60a6712c28e11e6458d5 upstream.

Now that we have the security flags we can significantly simplify the
code in pnv_setup_rfi_flush(), because we can use the flags instead of
checking device tree properties and because the security flags have
pessimistic defaults.

Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

powerpc/64s: Enhance the information in cpu_show_meltdown()

commit ff348355e9c72493947be337bb4fae4fc1a41eba upstream.

Now that we have the security feature flags we can make the
information displayed in the "meltdown" file more informative.

Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

powerpc/64s: Move cpu_show_meltdown()

commit 8ad33041563a10b34988800c682ada14b2612533 upstream.

This landed in setup_64.c for no good reason other than we had nowhere
else to put it. Now that we have a security-related file, that is a
better place for it so move it.

[mpe: Add extern for rfi_flush to fix bisection break]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

powerpc/powernv: Set or clear security feature flags

commit 77addf6e95c8689e478d607176b399a6242a777e upstream.

Now that we have feature flags for security related things, set or
clear them based on what we see in the device tree provided by
firmware.

Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

powerpc/pseries: Set or clear security feature flags

commit f636c14790ead6cc22cf62279b1f8d7e11a67116 upstream.

Now that we have feature flags for security related things, set or
clear them based on what we receive from the hypercall.

Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

powerpc: Add security feature flags for Spectre/Meltdown

commit 9a868f634349e62922c226834aa23e3d1329ae7f upstream.

This commit adds security feature flags to reflect the settings we
receive from firmware regarding Spectre/Meltdown mitigations.

The feature names reflect the names we are given by firmware on bare
metal machines. See the hostboot source for details.

Arguably these could be firmware features, but that then requires them
to be read early in boot so they're available prior to asm feature
patching, but we don't actually want to use them for patching. We may
also want to dynamically update them in future, which would be
incompatible with the way firmware features work (at the moment at
least). So for now just make them separate flags.

Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

powerpc/pseries: Add new H_GET_CPU_CHARACTERISTICS flags

commit c4bc36628d7f8b664657d8bd6ad1c44c177880b7 upstream.

Add some additional values which have been defined for the
H_GET_CPU_CHARACTERISTICS hypercall.

Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

powerpc/rfi-flush: Call setup_rfi_flush() after LPM migration

commit 921bc6cf807ceb2ab8005319cf39f33494d6b100 upstream.

We might have migrated to a machine that uses a different flush type,
or doesn't need flushing at all.

Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Mauricio Faria de Oliveira <mauricfo@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

powerpc/rfi-flush: Differentiate enabled and patched flush types

commit 0063d61ccfc011f379a31acaeba6de7c926fed2c upstream.

Currently the rfi-flush messages print 'Using <type> flush' for all
enabled_flush_types, but that is not necessarily true -- as now the
fallback flush is always enabled on pseries, but the fixup function
overwrites its nop/branch slot with other flush types, if available.

So, replace the 'Using <type> flush' messages with '<type> flush is
available'.

Also, print the patched flush types in the fixup function, so users
can know what is (not) being used (e.g., the slower, fallback flush,
or no flush type at all if flush is disabled via the debugfs switch).

Suggested-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Mauricio Faria de Oliveira <mauricfo@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

powerpc/rfi-flush: Always enable fallback flush on pseries

commit 84749a58b6e382f109abf1e734bc4dd43c2c25bb upstream.

This ensures the fallback flush area is always allocated on pseries,
so in case a LPAR is migrated from a patched to an unpatched system,
it is possible to enable the fallback flush in the target system.

Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Mauricio Faria de Oliveira <mauricfo@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

powerpc/rfi-flush: Make it possible to call setup_rfi_flush() again

commit abf110f3e1cea40f5ea15e85f5d67c39c14568a7 upstream.

For PowerVM migration we want to be able to call setup_rfi_flush()
again after we've migrated the partition.

To support that we need to check that we're not trying to allocate the
fallback flush area after memblock has gone away (i.e., boot-time only).

Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Mauricio Faria de Oliveira <mauricfo@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

powerpc/rfi-flush: Move the logic to avoid a redo into the debugfs code

commit 1e2a9fc7496955faacbbed49461d611b704a7505 upstream.

rfi_flush_enable() includes a check to see if we're already
enabled (or disabled), and in that case does nothing.

But that means calling setup_rfi_flush() a 2nd time doesn't actually
work, which is a bit confusing.

Move that check into the debugfs code, where it really belongs.

Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Mauricio Faria de Oliveira <mauricfo@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

powerpc/powernv: Support firmware disable of RFI flush

commit eb0a2d2620ae431c543963c8c7f08f597366fc60 upstream.

Some versions of firmware will have a setting that can be configured
to disable the RFI flush, add support for it.

Fixes: 6e032b350cd1 ("powerpc/powernv: Check device-tree for RFI flush settings")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

powerpc/pseries: Support firmware disable of RFI flush

commit 582605a429e20ae68fd0b041b2e840af296edd08 upstream.

Some versions of firmware will have a setting that can be configured
to disable the RFI flush, add support for it.

Fixes: 8989d56878a7 ("powerpc/pseries: Query hypervisor for RFI flush settings")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

powerpc/rfi-flush: Move out of HARDLOCKUP_DETECTOR #ifdef

The backport of the RFI flush support, done by me, has a minor bug in
that the code is inside an #ifdef CONFIG_HARDLOCKUP_DETECTOR, which is
incorrect.

This doesn't matter with common configs because we enable
HARDLOCKUP_DETECTOR, but with future patches it will break the build.
So fix it.

Fixes: c3b82ebee6e0 ("powerpc/64s: Add support for RFI flush of L1-D cache")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

arm64/cpufeature: don't use mutex in bringup path

commit 63a1e1c95e60e798fa09ab3c536fb555aa5bbf2b upstream.

Currently, cpus_set_cap() calls static_branch_enable_cpuslocked(), which
must take the jump_label mutex.

We call cpus_set_cap() in the secondary bringup path, from the idle
thread where interrupts are disabled. Taking a mutex in this path "is a
NONO" regardless of whether it's contended, and something we must avoid.
We didn't spot this until recently, as ___might_sleep() won't warn for
this case until all CPUs have been brought up.

This patch avoids taking the mutex in the secondary bringup path. The
poking of static keys is deferred until enable_cpu_capabilities(), which
runs in a suitable context on the boot CPU. To account for the static
keys being set later, cpus_have_const_cap() is updated to use another
static key to check whether the const cap keys have been initialised,
falling back to the caps bitmap until this is the case.

This means that users of cpus_have_const_cap() gain should only gain a
single additional NOP in the fast path once the const caps are
initialised, but should always see the current cap value.

The hyp code should never dereference the caps array, since the caps are
initialized before we run the module initcall to initialise hyp. A check
is added to the hyp init code to document this requirement.

This change will sidestep a number of issues when the upcoming hotplug
locking rework is merged.

Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Marc Zyniger <marc.zyngier@arm.com>
Reviewed-by: Suzuki Poulose <suzuki.poulose@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Cc: Christoffer Dall <christoffer.dall@linaro.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sebastian Sewior <bigeasy@linutronix.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
[4.9: this avoids an IPI before GICv3 is up, preventing a boot time crash]
Signed-off-by: Mark Rutland <mark.rutland@arm.com> [v4.9 backport]
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

arm64: Add hypervisor safe helper for checking constant capabilities

commit a4023f682739439b434165b54af7cb3676a4766e upstream.

The hypervisor may not have full access to the kernel data structures
and hence cannot safely use cpus_have_cap() helper for checking the
system capability. Add a safe helper for hypervisors to check a constant
system capability, which *doesn't* fall back to checking the bitmap
maintained by the kernel. With this, make the cpus_have_cap() only
check the bitmask and force constant cap checks to use the new API
for quicker checks.

Cc: Robert Ritcher <rritcher@cavium.com>
Cc: Tirumalesh Chalamarla <tchalamarla@cavium.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Reviewed-by: Will Deacon <will.deacon@arm.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
[4.9: restore cpus_have_const_cap() to previously-backported code]
Signed-off-by: Mark Rutland <mark.rutland@arm.com> [v4.9 backport]
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

scsi: ufs: Factor out ufshcd_read_desc_param

commit a4b0e8a4e92b1baa860e744847fbdb84a50a5071 upstream.

Since in UFS 2.1 specification some of the descriptor lengths differs
from 2.0 specification and some devices, which are reporting spec
version 2.0 have different descriptor lengths we can not rely on
hardcoded values taken from 2.0 specification. This patch introduces
reading these lengths per each device from descriptor headers at probe
time to ensure their correctness.

Signed-off-by: Michal' Potomski <michalx.potomski@intel.com>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
[Wei Li: Slight tweaks to get the cherry-pick to apply,resolved collisions]
Signed-off-by: Li Wei <liwei213@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

scsi: ufs: refactor device descriptor reading

commit 93fdd5ac64bbe80dac6416f048405362d7ef0945 upstream.

Pull device descriptor reading out of ufs quirk so it can be used also
for other purposes.

Revamp the fixup setup:

1. Rename ufs_device_info to ufs_dev_desc as very similar name
   ufs_dev_info is already in use.

2. Make the handlers static as they are not used out of the ufshdc.c
   file.

[mkp: applied by hand]

Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Li Wei <liwei213@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

scsi: ufs: fix failure to read the string descriptor

commit bde44bb665d049468b6a1a2fa7d666434de4f83f upstream.

While reading variable size descriptors (like string descriptor), some UFS
devices may report the "LENGTH" (field in "Transaction Specific fields" of
Query Response UPIU) same as what was requested in Query Request UPIU
instead of reporting the actual size of the variable size descriptor.
Although it's safe to ignore the "LENGTH" field for variable size
descriptors as we can always derive the length of the descriptor from
the descriptor header fields. Hence this change impose the length match
check only for fixed size descriptors (for which we always request the
correct size as part of Query Request UPIU).

Reviewed-by: Venkat Gopalakrishnan <venkatg@codeaurora.org>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
[Wei Li: Slight tweaks to get the cherry-pick to apply,resolved collisions.]
Signed-off-by: Li Wei <liwei213@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tcp: avoid integer overflows in tcp_rcv_space_adjust()

commit 607065bad9931e72207b0cac365d7d4abc06bd99 upstream.

When using large tcp_rmem[2] values (I did tests with 500 MB),
I noticed overflows while computing rcvwin.

Lets fix this before the following patch.

Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Wei Wang <weiwan@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
[Backport: sysctl_tcp_rmem is not Namespace-ify'd in older kernels]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

x86/amd: don't set X86_BUG_SYSRET_SS_ATTRS when running under Xen

Upstream commit: def9331a12977770cc6132d79f8e6565871e8e38 ("x86/amd:
don't set X86_BUG_SYSRET_SS_ATTRS when running under Xen")

When running as Xen pv guest X86_BUG_SYSRET_SS_ATTRS must not be set
on AMD cpus.

This bug/feature bit is kind of special as it will be used very early
when switching threads. Setting the bit and clearing it a little bit
later leaves a critical window where things can go wrong. This time
window has enlarged a little bit by using setup_clear_cpu_cap() instead
of the hypervisor's set_cpu_features callback. It seems this larger
window now makes it rather easy to hit the problem.

The proper solution is to never set the bit in case of Xen.

Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

xen: set cpu capabilities from xen_start_kernel()

Upstream commit: 0808e80cb760de2733c0527d2090ed2205a1eef8 ("xen: set
cpu capabilities from xen_start_kernel()")

There is no need to set the same capabilities for each cpu
individually. This can easily be done for all cpus when starting the
kernel.

Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

x86/amd: revert commit 944e0fc51a89c9827b9

Revert commit 944e0fc51a89c9827b98813d65dc083274777c7f ("x86/amd: don't
set X86_BUG_SYSRET_SS_ATTRS when running under Xen") as it is lacking
a prerequisite patch and is making things worse.

Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

platform/chrome: cros_ec_lpc: remove redundant pointer request

commit d3b56c566d4ba8cae688baf3cca94425d57ea783 upstream.

Pointer request is being assigned but never used, so remove it. Cleans
up the clang warning:

drivers/platform/chrome/cros_ec_lpc.c:68:2: warning: Value stored to
'request' is never read

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Benson Leung <bleung@chromium.org>
Cc: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ASoC: Intel: sst: remove redundant variable dma_dev_name

commit 271ef65b5882425d500e969e875c98e47a6b0c86 upstream.

The pointer dma_dev_name is assigned but never read, it is redundant
and can therefore be removed.

Cleans up clang warning:
sound/soc/intel/common/sst-firmware.c:288:3: warning: Value stored to
'dma_dev_name' is never read

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

rtlwifi: rtl8192cu: Remove variable self-assignment in rf.c

commit fb239c1209bb0f0b4830cc72507cc2f2d63fadbd upstream.

In _rtl92c_get_txpower_writeval_by_regulatory() the variable writeVal
is assigned to itself in an if ... else statement, apparently only to
document that the branch condition is handled and that a previously read
value should be returned unmodified. The self-assignment causes clang to
raise the following warning:

drivers/net/wireless/realtek/rtlwifi/rtl8192cu/rf.c:304:13:
  error: explicitly assigning value of variable of type 'u32'
    (aka 'unsigned int') to itself [-Werror,-Wself-assign]
  writeVal = writeVal;

Delete the branch with the self-assignment.

Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dma-buf: remove redundant initialization of sg_table

commit 531beb067c6185aceabfdee0965234c6a8fd133b upstream.

sg_table is being initialized and is never read before it is updated
again later on, hence making the initialization redundant. Remove
the initialization.

Detected by clang scan-build:
"warning: Value stored to 'sg_table' during its initialization is
never read"

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20170914230516.6056-1-colin.king@canonical.com
Cc: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

cfg80211: further limit wiphy names to 64 bytes

commit 814596495dd2b9d4aab92d8f89cf19060d25d2ea upstream.

wiphy names were recently limited to 128 bytes by commit a7cfebcb7594
("cfg80211: limit wiphy names to 128 bytes").  As it turns out though,
this isn't sufficient because dev_vprintk_emit() needs the syslog header
string "SUBSYSTEM=ieee80211\0DEVICE=+ieee80211:$devname" to fit into 128
bytes.  This triggered the "device/subsystem name too long" WARN when
the device name was >= 90 bytes.  As before, this was reproduced by
syzbot by sending an HWSIM_CMD_NEW_RADIO command to the MAC80211_HWSIM
generic netlink family.

Fix it by further limiting wiphy names to 64 bytes.

Reported-by: syzbot+e64565577af34b3768dc@syzkaller.appspotmail.com
Fixes: a7cfebcb7594 ("cfg80211: limit wiphy names to 128 bytes")
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

selinux: KASAN: slab-out-of-bounds in xattr_getsecurity

commit efe3de79e0b52ca281ef6691480c8c68c82a4657 upstream.

Call trace:
 [<ffffff9203a8d7a8>] dump_backtrace+0x0/0x428
 [<ffffff9203a8dbf8>] show_stack+0x28/0x38
 [<ffffff920409bfb8>] dump_stack+0xd4/0x124
 [<ffffff9203d187e8>] print_address_description+0x68/0x258
 [<ffffff9203d18c00>] kasan_report.part.2+0x228/0x2f0
 [<ffffff9203d1927c>] kasan_report+0x5c/0x70
 [<ffffff9203d1776c>] check_memory_region+0x12c/0x1c0
 [<ffffff9203d17cdc>] memcpy+0x34/0x68
 [<ffffff9203d75348>] xattr_getsecurity+0xe0/0x160
 [<ffffff9203d75490>] vfs_getxattr+0xc8/0x120
 [<ffffff9203d75d68>] getxattr+0x100/0x2c8
 [<ffffff9203d76fb4>] SyS_fgetxattr+0x64/0xa0
 [<ffffff9203a83f70>] el0_svc_naked+0x24/0x28

If user get root access and calls security.selinux setxattr() with an
embedded NUL on a file and then if some process performs a getxattr()
on that file with a length greater than the actual length of the string,
it would result in a panic.

To fix this, add the actual length of the string to the security context
instead of the length passed by the userspace process.

Signed-off-by: Sachin Grover <sgrover@codeaurora.org>
Cc: stable@vger.kernel.org
Signed-off-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tracing: Fix crash when freeing instances with event triggers

commit 86b389ff22bd6ad8fd3cb98e41cd271886c6d023 upstream.

If a instance has an event trigger enabled when it is freed, it could cause
an access of free memory. Here's the case that crashes:

 # cd /sys/kernel/tracing
 # mkdir instances/foo
 # echo snapshot > instances/foo/events/initcall/initcall_start/trigger
 # rmdir instances/foo

Would produce:

 general protection fault: 0000 [#1] PREEMPT SMP PTI
 Modules linked in: tun bridge ...
 CPU: 5 PID: 6203 Comm: rmdir Tainted: G        W         4.17.0-rc4-test+ #933
 Hardware name: Hewlett-Packard HP Compaq Pro 6300 SFF/339A, BIOS K01 v03.03 07/14/2016
 RIP: 0010:clear_event_triggers+0x3b/0x70
 RSP: 0018:ffffc90003783de0 EFLAGS: 00010286
 RAX: 0000000000000000 RBX: 6b6b6b6b6b6b6b2b RCX: 0000000000000000
 RDX: 0000000000000000 RSI: 0000000000000000 RDI: ffff8800c7130ba0
 RBP: ffffc90003783e00 R08: ffff8801131993f8 R09: 0000000100230016
 R10: ffffc90003783d80 R11: 0000000000000000 R12: ffff8800c7130ba0
 R13: ffff8800c7130bd8 R14: ffff8800cc093768 R15: 00000000ffffff9c
 FS:  00007f6f4aa86700(0000) GS:ffff88011eb40000(0000) knlGS:0000000000000000
 CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
 CR2: 00007f6f4a5aed60 CR3: 00000000cd552001 CR4: 00000000001606e0
 Call Trace:
  event_trace_del_tracer+0x2a/0xc5
  instance_rmdir+0x15c/0x200
  tracefs_syscall_rmdir+0x52/0x90
  vfs_rmdir+0xdb/0x160
  do_rmdir+0x16d/0x1c0
  __x64_sys_rmdir+0x17/0x20
  do_syscall_64+0x55/0x1a0
  entry_SYSCALL_64_after_hwframe+0x49/0xbe

This was due to the call the clears out the triggers when an instance is
being deleted not removing the trigger from the link list.

Cc: stable@vger.kernel.org
Fixes: 85f2b08268c01 ("tracing: Add basic event trigger framework")
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Input: elan_i2c_smbus - fix corrupted stack

commit 40f7090bb1b4ec327ea1e1402ff5783af5b35195 upstream.

New ICs (like the one on the Lenovo T480s) answer to
ETP_SMBUS_IAP_VERSION_CMD 4 bytes instead of 3. This corrupts the stack
as i2c_smbus_read_block_data() uses the values returned by the i2c
device to know how many data it need to return.

i2c_smbus_read_block_data() can read up to 32 bytes (I2C_SMBUS_BLOCK_MAX)
and there is no safeguard on how many bytes are provided in the return
value. Ensure we always have enough space for any future firmware.
Also 0-initialize the values to prevent any access to uninitialized memory.

Cc: <stable@vger.kernel.org> # v4.4.x, v4.9.x, v4.14.x, v4.15.x, v4.16.x
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: KT Liao <kt.liao@emc.com.tw>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Revert "ima: limit file hash setting by user to fix and log modes"

commit f5acb3dcba1ffb7f0b8cbb9dba61500eea5d610b upstream.

Userspace applications have been modified to write security xattrs,
but they are not context aware.  In the case of security.ima, the
security xattr can be either a file hash or a file signature.
Permitting writing one, but not the other requires the application to
be context aware.

In addition, userspace applications might write files to a staging
area, which might not be in policy, and then change some file metadata
(eg. owner) making it in policy.  As a result, these files are not
labeled properly.

This reverts commit c68ed80c97d9720f51ef31fe91560fdd1e121533, which
prevents writing file hashes as security.ima xattrs.

Requested-by: Patrick Ohly <patrick.ohly@intel.com>
Cc: Dmitry Kasatkin <dmitry.kasatkin@gmail.com>
Signed-off-by: Mimi Zohar <zohar@linux.vnet.ibm.com>
Cc: Mike Rapoport <rppt@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

xfs: detect agfl count corruption and reset agfl

commit a27ba2607e60312554cbcd43fc660b2c7f29dc9c upstream.

The struct xfs_agfl v5 header was originally introduced with
unexpected padding that caused the AGFL to operate with one less
slot than intended. The header has since been packed, but the fix
left an incompatibility for users who upgrade from an old kernel
with the unpacked header to a newer kernel with the packed header
while the AGFL happens to wrap around the end. The newer kernel
recognizes one extra slot at the physical end of the AGFL that the
previous kernel did not. The new kernel will eventually attempt to
allocate a block from that slot, which contains invalid data, and
cause a crash.

This condition can be detected by comparing the active range of the
AGFL to the count. While this detects a padding mismatch, it can
also trigger false positives for unrelated flcount corruption. Since
we cannot distinguish a size mismatch due to padding from unrelated
corruption, we can't trust the AGFL enough to simply repopulate the
empty slot.

Instead, avoid unnecessarily complex detection logic and and use a
solution that can handle any form of flcount corruption that slips
through read verifiers: distrust the entire AGFL and reset it to an
empty state. Any valid blocks within the AGFL are intentionally
leaked. This requires xfs_repair to rectify (which was already
necessary based on the state the AGFL was found in). The reset
mitigates the side effect of the padding mismatch problem from a
filesystem crash to a free space accounting inconsistency. The
generic approach also means that this patch can be safely backported
to kernels with or without a packed struct xfs_agfl.

Check the AGF for an invalid freelist count on initial read from
disk. If detected, set a flag on the xfs_perag to indicate that a
reset is required before the AGFL can be used. In the first
transaction that attempts to use a flagged AGFL, reset it to empty,
warn the user about the inconsistency and allow the freelist fixup
code to repopulate the AGFL with new blocks. The xfs_perag flag is
cleared to eliminate the need for repeated checks on each block
allocation operation.

This allows kernels that include the packing fix commit 96f859d52bcb
("libxfs: pack the agfl header structure so XFS_AGFL_SIZE is correct")
to handle older unpacked AGFL formats without a filesystem crash.

Suggested-by: Dave Chinner <david@fromorbit.com>
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by Dave Chiluk <chiluk+linuxxfs@indeed.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Dave Chiluk <chiluk+linuxxfs@indeed.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Revert "pinctrl: msm: Use dynamic GPIO numbering"

This reverts commit 0bd77073e693e8f93ff6ddba65a9f426153221cb which is
commit a7aa75a2a7dba32594291a71c3704000a2fd7089 upstream.

There's been too many complaints about this.  Personally I think it's
going to blow up when people hit this in mainline, but hey, it's not my
systems.  At least we don't have to backport the mess to the stable
kernels to give them some more life to live unscathed :)

Reported-by: Timur Tabi <timur@codeaurora.org>
Reported-by: Sebastian Gottschall <s.gottschall@dd-wrt.com>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: serial: cp210x: use tcflag_t to fix incompatible pointer type

commit 009615ab7fd4e43b82a38e4e6adc5e23c1ee567f upstream.

On sparc32, tcflag_t is unsigned long, unlike all other architectures:

    drivers/usb/serial/cp210x.c: In function 'cp210x_get_termios':
    drivers/usb/serial/cp210x.c:717:3: warning: passing argument 2 of 'cp210x_get_termios_port' from incompatible pointer type
       cp210x_get_termios_port(tty->driver_data,
       ^
    drivers/usb/serial/cp210x.c:35:13: note: expected 'unsigned int *' but argument is of type 'tcflag_t *'
     static void cp210x_get_termios_port(struct usb_serial_port *port,
 ^

Consistently use tcflag_t to fix this.

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Cc: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

powerpc/64s: Clear PCR on boot

commit faf37c44a105f3608115785f17cbbf3500f8bc71 upstream.

Clear the PCR (Processor Compatibility Register) on boot to ensure we
are not running in a compatibility mode.

We've seen this cause problems when a crash (and kdump) occurs while
running compat mode guests. The kdump kernel then runs with the PCR
set and causes problems. The symptom in the kdump kernel (also seen in
petitboot after fast-reboot) is early userspace programs taking
sigills on newer instructions (seen in libc).

Signed-off-by: Michael Neuling <mikey@neuling.org>
Cc: stable@vger.kernel.org
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

arm64: lse: Add early clobbers to some input/output asm operands

commit 32c3fa7cdf0c4a3eb8405fc3e13398de019e828b upstream.

For LSE atomics that read and write a register operand, we need to
ensure that these operands are annotated as "early clobber" if the
register is written before all of the input operands have been consumed.
Failure to do so can result in the compiler allocating the same register
to both operands, leading to splats such as:

 Unable to handle kernel paging request at virtual address 11111122222221
 [...]
 x1 : 1111111122222222 x0 : 1111111122222221
 Process swapper/0 (pid: 1, stack limit = 0x000000008209f908)
 Call trace:
  test_atomic64+0x1360/0x155c

where x0 has been allocated as both the value to be stored and also the
atomic_t pointer.

This patch adds the missing clobbers.

Cc: <stable@vger.kernel.org>
Cc: Dave Martin <dave.martin@arm.com>
Cc: Robin Murphy <robin.murphy@arm.com>
Reported-by: Mark Salter <msalter@redhat.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Linux 4.9.106

objtool: Enclose contents of unreachable() macro in a block

commit 4e4636cf981b5b629fbfb78aa9f232e015f7d521 upstream.

Guenter Roeck reported a boot failure in mips64.  It was bisected to the
following commit:

  d1091c7fa3d5 ("objtool: Improve detection of BUG() and other dead ends")

The unreachable() macro was formerly only composed of a single
statement.  The above commit added a second statement, but neglected to
enclose the statements in a block.

Suggested-by: Guenter Roeck <linux@roeck-us.net>
Reported-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Fixes: d1091c7fa3d5 ("objtool: Improve detection of BUG() and other dead ends")
Link: http://lkml.kernel.org/r/20170228042116.glmwmwiohcix7o4a@treble
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

x86/xen: Add unwind hint annotations to xen_setup_gdt

Not needed in mainline as this function got rewritten in 4.12

This enables objtool to grok the iret in the middle of a C function.

This matches commit 76846bf3cb09 ("x86/asm: Add unwind hint annotations
to sync_core()")

Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

objtool: header file sync-up

When building tools/objtool/ it rightly complains about a number of
files being out of sync.  Fix this up by syncing them properly with the
relevant in-kernel versions.

Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

perf/tools: header file sync up

When building tools/perf/ it rightly complains about a number of .h
files being out of sync.  Fix this up by syncing them properly with the
relevant in-kernel versions.

Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

objtool, x86: Add several functions and files to the objtool whitelist

commit c207aee48037abca71c669cbec407b9891965c34 upstream.

In preparation for an objtool rewrite which will have broader checks,
whitelist functions and files which cause problems because they do
unusual things with the stack.

These whitelists serve as a TODO list for which functions and files
don't yet have undwarf unwinder coverage.  Eventually most of the
whitelists can be removed in favor of manual CFI hint annotations or
objtool improvements.

Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: live-patching@vger.kernel.org
Link: http://lkml.kernel.org/r/7f934a5d707a574bda33ea282e9478e627fb1829.1498659915.git.jpoimboe@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

objtool: Fix "noreturn" detection for recursive sibling calls

commit 0afd0d9e0e7879d666c1df2fa1bea4d8716909fe upstream.

Objtool has some crude logic for detecting static "noreturn" functions
(aka "dead ends").  This is necessary for being able to correctly follow
GCC code flow when such functions are called.

It's remotely possible for two functions to call each other via sibling
calls.  If they don't have RET instructions, objtool's noreturn
detection logic goes into a recursive loop:

  drivers/char/ipmi/ipmi_ssif.o: warning: objtool: return_hosed_msg()+0x0: infinite recursion (objtool bug!)
  drivers/char/ipmi/ipmi_ssif.o: warning: objtool: deliver_recv_msg()+0x0: infinite recursion (objtool bug!)

Instead of reporting an error in this case, consider the functions to be
non-dead-ends.

Reported-and-tested-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: David Laight <David.Laight@ACULAB.COM>
Cc: Greg KH <gregkh@linuxfoundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: damian <damian.tometzki@icloud.com>
Link: http://lkml.kernel.org/r/7cc156408c5781a1f62085d352ced1fe39fe2f91.1525923412.git.jpoimboe@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

objtool: Detect RIP-relative switch table references, part 2

commit 7dec80ccbe310fb7e225bf21c48c672bb780ce7b upstream.

With the following commit:

  fd35c88b7417 ("objtool: Support GCC 8 switch tables")

I added a "can't find switch jump table" warning, to stop covering up
silent failures if add_switch_table() can't find anything.

That warning found yet another bug in the objtool switch table detection
logic.  For cases 1 and 2 (as described in the comments of
find_switch_table()), the find_symbol_containing() check doesn't adjust
the offset for RIP-relative switch jumps.

Incidentally, this bug was already fixed for case 3 with:

  6f5ec2993b1f ("objtool: Detect RIP-relative switch table references")

However, that commit missed the fix for cases 1 and 2.

The different cases are now starting to look more and more alike.  So
fix the bug by consolidating them into a single case, by checking the
original dynamic jump instruction in the case 3 loop.

This also simplifies the code and makes it more robust against future
switch table detection issues -- of which I'm sure there will be many...

Switch table detection has been the most fragile area of objtool, by
far.  I long for the day when we'll have a GCC plugin for annotating
switch tables.  Linus asked me to delay such a plugin due to the
flakiness of the plugin infrastructure in older versions of GCC, so this
rickety code is what we're stuck with for now.  At least the code is now
a little simpler than it was.

Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/f400541613d45689086329432f3095119ffbc328.1526674218.git.jpoimboe@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

objtool: Detect RIP-relative switch table references

commit 6f5ec2993b1f39aed12fa6fd56e8dc2272ee8a33 upstream.

Typically a switch table can be found by detecting a .rodata access
followed an indirect jump:

    1969: 4a 8b 0c e5 00 00 00  mov    0x0(,%r12,8),%rcx
    1970: 00
196d: R_X86_64_32S .rodata+0x438
    1971: e9 00 00 00 00        jmpq   1976 <dispc_runtime_suspend+0xb6a>
1972: R_X86_64_PC32 __x86_indirect_thunk_rcx-0x4

Randy Dunlap reported a case (seen with GCC 4.8) where the .rodata
access uses RIP-relative addressing:

    19bd: 48 8b 3d 00 00 00 00  mov    0x0(%rip),%rdi        # 19c4 <dispc_runtime_suspend+0xbb8>
19c0: R_X86_64_PC32 .rodata+0x45c
    19c4: e9 00 00 00 00        jmpq   19c9 <dispc_runtime_suspend+0xbbd>
19c5: R_X86_64_PC32 __x86_indirect_thunk_rdi-0x4

In this case the relocation addend needs to be adjusted accordingly in
order to find the location of the switch table.

The fix is for case 3 (as described in the comments), but also make the
existing case 1 & 2 checks more precise by only adjusting the addend for
R_X86_64_PC32 relocations.

This fixes the following warnings:

  drivers/video/fbdev/omap2/omapfb/dss/dispc.o: warning: objtool: dispc_runtime_suspend()+0xbb8: sibling call from callable instruction with modified stack frame
  drivers/video/fbdev/omap2/omapfb/dss/dispc.o: warning: objtool: dispc_runtime_resume()+0xcc5: sibling call from callable instruction with modified stack frame

Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/b6098294fd67afb69af8c47c9883d7a68bf0f8ea.1526305958.git.jpoimboe@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

objtool: Support GCC 8 switch tables

commit fd35c88b74170d9335530d9abf271d5d73eb5401 upstream.

With GCC 8, some issues were found with the objtool switch table
detection.

1) In the .rodata section, immediately after the switch table, there can
   be another object which contains a pointer to the function which had
   the switch statement.  In this case objtool wrongly considers the
   function pointer to be part of the switch table.  Fix it by:

   a) making sure there are no pointers to the beginning of the
      function; and

   b) making sure there are no gaps in the switch table.

   Only the former was needed, the latter adds additional protection for
   future optimizations.

2) In find_switch_table(), case 1 and case 2 are missing the check to
   ensure that the .rodata switch table data is anonymous, i.e. that it
   isn't already associated with an ELF symbol.  Fix it by adding the
   same find_symbol_containing() check which is used for case 3.

This fixes the following warnings with GCC 8:

  drivers/block/virtio_blk.o: warning: objtool: virtio_queue_rq()+0x0: stack state mismatch: cfa1=7+8 cfa2=7+72
  net/ipv6/icmp.o: warning: objtool: icmpv6_rcv()+0x0: stack state mismatch: cfa1=7+8 cfa2=7+64
  drivers/usb/core/quirks.o: warning: objtool: quirks_param_set()+0x0: stack state mismatch: cfa1=7+8 cfa2=7+48
  drivers/mtd/nand/raw/nand_hynix.o: warning: objtool: hynix_nand_decode_id()+0x0: stack state mismatch: cfa1=7+8 cfa2=7+24
  drivers/mtd/nand/raw/nand_samsung.o: warning: objtool: samsung_nand_decode_id()+0x0: stack state mismatch: cfa1=7+8 cfa2=7+32
  drivers/gpu/drm/nouveau/nvkm/subdev/top/gk104.o: warning: objtool: gk104_top_oneinit()+0x0: stack state mismatch: cfa1=7+8 cfa2=7+64

Reported-by: Arnd Bergmann <arnd@arndb.de>
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: David Laight <David.Laight@ACULAB.COM>
Cc: Greg KH <gregkh@linuxfoundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: damian <damian.tometzki@icloud.com>
Link: http://lkml.kernel.org/r/20180510224849.xwi34d6tzheb5wgw@treble
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

objtool: Support GCC 8's cold subfunctions

commit 13810435b9a7014fb92eb715f77da488f3b65b99 upstream.

GCC 8 moves a lot of unlikely code out of line to "cold" subfunctions in
.text.unlikely.  Properly detect the new subfunctions and treat them as
extensions of the original functions.

This fixes a bunch of warnings like:

  kernel/cgroup/cgroup.o: warning: objtool: parse_cgroup_root_flags()+0x33: sibling call from callable instruction with modified stack frame
  kernel/cgroup/cgroup.o: warning: objtool: cgroup_addrm_files()+0x290: sibling call from callable instruction with modified stack frame
  kernel/cgroup/cgroup.o: warning: objtool: cgroup_apply_control_enable()+0x25b: sibling call from callable instruction with modified stack frame
  kernel/cgroup/cgroup.o: warning: objtool: rebind_subsystems()+0x325: sibling call from callable instruction with modified stack frame

Reported-and-tested-by: damian <damian.tometzki@icloud.com>
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: David Laight <David.Laight@ACULAB.COM>
Cc: Greg KH <gregkh@linuxfoundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/0965e7fcfc5f31a276f0c7f298ff770c19b68706.1525923412.git.jpoimboe@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

objtool: sync up with the 4.14.47 version of objtool

There are pros and cons of dealing with tools in the kernel directory.
The pros are the fact that development happens fast, and new features
can be added to the kernel and the tools at the same times.  The cons
are when dealing with backported kernel patches, it can be necessary to
backport parts of the tool changes as well.

For 4.9.y so far, we have backported individual patches.  That quickly
breaks down when there are minor differences between how backports were
handled, so grabbing 40+ patch long series can be difficult, not
impossible, but really frustrating to attempt.

To help mitigate this mess, here's a single big patch to sync up the
objtool logic to the 4.14.47 version of the tool.  From this point
forward (after some other minor header file patches are applied), the
tool should be in sync and much easier to maintain over time.

This has survivied my limited testing, and as the codebase is identical
to 4.14.47, I'm pretty comfortable dropping this big change in here in
4.9.y.  Hopefully all goes well...

Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tools include: Include missing headers for fls() and types in linux/log2.h

commit a12a4e023a55f058178afea1ada3ce7bf4db94c3 upstream.

Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/n/tip-7wj865zidu5ylf87i6i7v6z7@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tools include: Drop ARRAY_SIZE() definition from linux/hashtable.h

commit 68289cbd83eaa20faef7cc818121bc8e769065de upstream.

As tools/include/linux/kernel.h has it now, with the goodies present in
the kernel.h counterpart, i.e. checking that the parameter is an array
at build time.

Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/n/tip-v0b41ivu6z6dyugbq9ffa9ez@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tools include: Move ARRAY_SIZE() to linux/kernel.h

commit 8607c1ee734d12f62c6a46abef13a510e25a1839 upstream.

To match the kernel, then look for places redefining it to make it use
this version, which checks that its parameter is an array at build time.

Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/n/tip-txlcf1im83bcbj6kh0wxmyy8@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tools include: Adopt __same_type() and __must_be_array() from the kernel

commit f6441aff8946f7fd6ab730d7eb9eba18a9ebeba4 upstream.

Will be used to adopt the more stringent version of ARRAY_SIZE(), the
one in the kernel sources.

Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/n/tip-d85dpvay1hoqscpezlntyd8x@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tools include: Introduce linux/bug.h, from the kernel sources

commit 379d61b1c7d42512cded04d372f15a7e725db9e1 upstream.

With just what we will need in the upcoming changesets, the
BUILD_BUG_ON_ZERO() definition.

Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/n/tip-lw8zg7x6ttwcvqhp90mwe3vo@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tools include uapi: Grab copies of stat.h and fcntl.h

commit 67ef28794d7e30f33936d655f2951e8dcae7cd5a upstream.

We will need it to build tools/perf/trace/beauty/statx.h.

Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/n/tip-nin41ve2fa63lrfbdr6x57yr@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>