platform/kernel/u-boot.git
6 years agoboard: sun50i: Add Amarula A64-Relic initial support
Jagan Teki [Mon, 28 May 2018 11:04:43 +0000 (16:34 +0530)]
board: sun50i: Add Amarula A64-Relic initial support

Amarula A64-Relic is A64 based IoT device, which support
- Allwinner A64 Cortex-A53
- Mali-400MP2 GPU
- AXP803 PMIC
- 1GB DDR3 RAM
- 8GB eMMC
- AP6330 Wifi/BLE
- MIPI-DSI
- CSI: OV5640 sensor
- USB OTG
- 12V DC power supply

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
6 years agoconfigs: orangepi-prime: Enable USB OTG peripheral mode
Jagan Teki [Mon, 7 May 2018 07:33:51 +0000 (13:03 +0530)]
configs: orangepi-prime: Enable USB OTG peripheral mode

Enable USB_MUSB_GADGET which operate OTG in peripheral mode

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
6 years agoarm64: allwinner: h5: orangepi-prime: Sync usb otg nodes from Linux
Jagan Teki [Mon, 7 May 2018 07:33:50 +0000 (13:03 +0530)]
arm64: allwinner: h5: orangepi-prime: Sync usb otg nodes from Linux

orangepi-prime has usb otg routed host with either EHCI0/OHCI0
sync the same from Linux.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
6 years agoconfigs: orangepi-pc2: Enable USB OTG peripheral mode
Jagan Teki [Mon, 7 May 2018 07:33:49 +0000 (13:03 +0530)]
configs: orangepi-pc2: Enable USB OTG peripheral mode

Enable USB_MUSB_GADGET which operate OTG in peripheral mode

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
6 years agoarm64: allwinner: h5: orangepi-pc2: Sync usb otg nodes from Linux
Jagan Teki [Mon, 7 May 2018 07:33:48 +0000 (13:03 +0530)]
arm64: allwinner: h5: orangepi-pc2: Sync usb otg nodes from Linux

orangepi-pc2 has usb otg routed host with either EHCI0/OHCI0
sync the same from Linux.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
6 years agoarm64: allwinner: h5: orangepi-pc2: Order nodes in alphabetic
Jagan Teki [Mon, 7 May 2018 07:33:47 +0000 (13:03 +0530)]
arm64: allwinner: h5: orangepi-pc2: Order nodes in alphabetic

Order sun50i-h5-orangepi-pc2.dts nodes in alphabetic

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
6 years agoconfigs: bananapi-m2-plus: Enable USB OTG peripheral mode
Jagan Teki [Mon, 7 May 2018 07:33:46 +0000 (13:03 +0530)]
configs: bananapi-m2-plus: Enable USB OTG peripheral mode

Enable USB_MUSB_GADGET which operate OTG in peripheral mode

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
6 years agoARM: dts: sun8i-h3: bananapi-m2-plus: Sync usb otg nodes from Linux
Jagan Teki [Mon, 7 May 2018 07:33:45 +0000 (13:03 +0530)]
ARM: dts: sun8i-h3: bananapi-m2-plus: Sync usb otg nodes from Linux

Bananapi-m2-plus has usb otg routed host with either EHCI0/OHCI0
sync the same from Linux.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
6 years agoarm64: allwinner: a64: bananapi-m64: Sync usb host nodes from Linux
Jagan Teki [Mon, 7 May 2018 07:33:44 +0000 (13:03 +0530)]
arm64: allwinner: a64: bananapi-m64: Sync usb host nodes from Linux

Sync bananapi-m64 usb host nodes from Linux.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
6 years agoARM: dts: sun8i: a83t: Sync usbphy node from Linux
Jagan Teki [Mon, 7 May 2018 07:33:43 +0000 (13:03 +0530)]
ARM: dts: sun8i: a83t: Sync usbphy node from Linux

Sync sun8i-a83t usbphy node details from Linux.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
6 years agoconfigs: bananapi-m64: Enable USB OTG peripheral mode
Jagan Teki [Mon, 7 May 2018 07:33:42 +0000 (13:03 +0530)]
configs: bananapi-m64: Enable USB OTG peripheral mode

Enable USB_MUSB_GADGET which operate OTG in peripheral mode

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
6 years agoarm64: allwinner: a64: bananapi-m64: Sync usb_otg node from Linux
Jagan Teki [Mon, 7 May 2018 07:33:41 +0000 (13:03 +0530)]
arm64: allwinner: a64: bananapi-m64: Sync usb_otg node from Linux

Sync bananapi-m64 usb_otg node from Linux.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
6 years agosunxi: h3: Sync OTG and HCI nodes from Linux DT
Jun Nie [Mon, 7 May 2018 07:33:40 +0000 (13:03 +0530)]
sunxi: h3: Sync OTG and HCI nodes from Linux DT

Allwinner H3 have a dual-routed USB PHY0 -- routed to either OHCI/EHCI
or MUSB controller.

Signed-off-by: Jun Nie <jun.nie@linaro.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
6 years agosunxi: Drop legacy usb_phy.c
Jagan Teki [Fri, 25 May 2018 10:02:17 +0000 (15:32 +0530)]
sunxi: Drop legacy usb_phy.c

Allwinner PHY USB code is now part of generic-phy framework,
so drop existing legacy handling like arch/arm/mach-sunxi.c
and related code areas.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
6 years agousb: sunxi: Switch to use generic-phy
Jagan Teki [Mon, 7 May 2018 07:33:38 +0000 (13:03 +0530)]
usb: sunxi: Switch to use generic-phy

Allwinner USB PHY handling can be done through driver-model
generic-phy so add the generic-phy ops to relevant places
on host and musb sunxi driver and enable them in respective
SOC's.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
6 years agophy: sun4i-usb: Add a sunxi specific function for setting squelch-detect
Jagan Teki [Mon, 7 May 2018 07:33:37 +0000 (13:03 +0530)]
phy: sun4i-usb: Add a sunxi specific function for setting squelch-detect

The sunxi otg phy has a bug where it wrongly detects a high speed squelch
when reset on the root port gets de-asserted with a lo-speed device.

The workaround for this is to disable squelch detect before de-asserting
reset, and re-enabling it after the reset de-assert is done. Add a sunxi
specific phy function to allow the sunxi-musb glue to do this.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
6 years agoboard: sunxi: Use generic-phy for board_usb_cable_connected
Jagan Teki [Mon, 7 May 2018 07:33:36 +0000 (13:03 +0530)]
board: sunxi: Use generic-phy for board_usb_cable_connected

Allwinner PHY USB code is now part of generic-phy framework,
so use it in board_usb_cable_connected.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
6 years agodevice-tree-bindings: phy: Sync sun4i-usb-phy bindings
Jagan Teki [Wed, 9 May 2018 06:05:51 +0000 (11:35 +0530)]
device-tree-bindings: phy: Sync sun4i-usb-phy bindings

Sync sun4i-usb-phy bindings from Linux, since the
drivers/phy/allwinner/phy-sun4i-usb.c follow similar.

Sync changes from Linux with below commit:
"phy: sun4i-usb: add support for R40 USB PHY"
(sha1: f3d96f8d23d8e6d0b7642ee946b9b2ac3418fb4d)

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
6 years agophy: sun4i-usb: Add A23 USB PHY config
Jagan Teki [Mon, 7 May 2018 07:33:34 +0000 (13:03 +0530)]
phy: sun4i-usb: Add A23 USB PHY config

Allwinner A23 has 2 USB PHY's and 0x04 has phy ctrl offset.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
6 years agophy: sun4i-usb: Add A33 USB PHY config
Jagan Teki [Mon, 7 May 2018 07:33:33 +0000 (13:03 +0530)]
phy: sun4i-usb: Add A33 USB PHY config

Allwinner A33 has 2 USB PHY's and 0x10 has phy ctrl offset.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
6 years agophy: sun4i-usb: Add A31 PHY config
Jagan Teki [Mon, 7 May 2018 07:33:32 +0000 (13:03 +0530)]
phy: sun4i-usb: Add A31 PHY config

Allwinner A31 has 3 USB PHY's and rest similar to A10.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
6 years agophy: sun4i-usb: Add A10/A13/A20 PHY config
Jagan Teki [Mon, 7 May 2018 07:33:31 +0000 (13:03 +0530)]
phy: sun4i-usb: Add A10/A13/A20 PHY config

Add PHY configs for Allwinner A10/A13/A20 which are SUN4I.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
6 years agophy: sun4i-usb: Add A83T USB PHY config
Jagan Teki [Mon, 7 May 2018 07:33:30 +0000 (13:03 +0530)]
phy: sun4i-usb: Add A83T USB PHY config

Unlike, other Allwinner SUN4I Phy supporting SOC, A83T has
2 USB PHY's and second one is HSIC. So phy control need to
configure to handle these HSIC and SIDDQ requirement.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
6 years agophy: sun4i-usb: Add V3S PHY config
Jagan Teki [Mon, 7 May 2018 07:33:29 +0000 (13:03 +0530)]
phy: sun4i-usb: Add V3S PHY config

V3S has 1 USB PHY, rest are similar to A64.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
6 years agophy: sun4i-usb: Add H3/H5 PHY config
Jagan Teki [Mon, 7 May 2018 07:33:28 +0000 (13:03 +0530)]
phy: sun4i-usb: Add H3/H5 PHY config

H3/H5 has 4 USB PHY, rest are similar to A64.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
6 years agophy: sun4i-usb: Add id_detect and vbus_detect ops
Jagan Teki [Mon, 7 May 2018 07:33:27 +0000 (13:03 +0530)]
phy: sun4i-usb: Add id_detect and vbus_detect ops

ID and VBUS detection code require when musb changing
between Host and/or Peripheral modes.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
6 years agophy: Add Allwinner A64 USB PHY driver
Jagan Teki [Mon, 7 May 2018 07:33:26 +0000 (13:03 +0530)]
phy: Add Allwinner A64 USB PHY driver

USB PHY implementation for Allwinner SOC's can be handling
in to single driver with different phy configs.

This driver handle all Allwinner USB PHY's start from 4I to
50I(except 9I). Currently added A64 compatibility more will
add in next coming patches.

Current implementation is unable to get pinctrl, clock and reset
details from DT since the dm code on these will add it future.

Driver named as phy-sun4i-usb.c since the same PHY logic
work for all Allwinner SOC's start from 4I to A64 except 9I
with different phy configurations.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
6 years agomusb: sunxi: Add support for H3/H5/A64
Jagan Teki [Mon, 7 May 2018 07:33:25 +0000 (13:03 +0530)]
musb: sunxi: Add support for H3/H5/A64

Like other Allwinner SoC, the H3/H5/A64 is missing the config register
from the musb hardware block. Use a known working value for it
like other SoC.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
6 years agosunxi: clock: Fix OHCI clock gating for H3/H5
Chen-Yu Tsai [Mon, 7 May 2018 07:33:24 +0000 (13:03 +0530)]
sunxi: clock: Fix OHCI clock gating for H3/H5

Clock gating bits on H43/H5 were wrong, fix them.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
6 years agomusb: sunxi: Use BIT instead of numerical shift
Jagan Teki [Mon, 7 May 2018 07:33:23 +0000 (13:03 +0530)]
musb: sunxi: Use BIT instead of numerical shift

Use BIT is possible areas instead of numerical shift.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
6 years agomusb: sunxi: Add OTG device clkgate and reset for H3/H5
Jagan Teki [Mon, 7 May 2018 07:33:22 +0000 (13:03 +0530)]
musb: sunxi: Add OTG device clkgate and reset for H3/H5

Add OTG device clkgate and reset for H3/H5 through driver_data.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
6 years agosunxi: clock: Fix clock gating for H3/H5/A64
Jagan Teki [Mon, 7 May 2018 07:33:21 +0000 (13:03 +0530)]
sunxi: clock: Fix clock gating for H3/H5/A64

clock gating bits on a64 are different than H3_H5, so fixed
only required bits on clock_sun6i.h.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
6 years agomusb: sunxi: Add fifo config
Jagan Teki [Mon, 7 May 2018 07:33:20 +0000 (13:03 +0530)]
musb: sunxi: Add fifo config

Unlike other Allwinner SOC's H3/H5/V3s OTG support 4 endpoints
with relevant fifo configs, rest all have 5 endpoints.
So add the fifo configs and defer them based on driver_data.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
6 years agomusb: sunxi: Use simple way to fill musb_hdrc pdata
Jagan Teki [Mon, 7 May 2018 07:33:19 +0000 (13:03 +0530)]
musb: sunxi: Use simple way to fill musb_hdrc pdata

Filling musb_hdrc pdata using structure will unnecessary
add extra ifdefs, so fill them inside probe call for
better code understanding and get rid ifdefs using
devicetree compatible.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
6 years agomusb: sunxi: Add proper macros instead of numericals
Jagan Teki [Mon, 7 May 2018 07:33:18 +0000 (13:03 +0530)]
musb: sunxi: Add proper macros instead of numericals

- add proper macros for musb_config members
- use bool 'true' for multipoint and dyn_fifo instead of numerical 1

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
6 years agousb: sunxi: Simplify ccm reg base code
Jagan Teki [Mon, 7 May 2018 07:33:17 +0000 (13:03 +0530)]
usb: sunxi: Simplify ccm reg base code

Move struct sunxi_ccm_reg pointer to private structure
so-that accessing ccm reg base become more proper way
and avoid local initialization in each function.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
6 years agoRevert "sunxi: binman: Add U-Boot binary size check"
Maxime Ripard [Mon, 14 May 2018 14:22:47 +0000 (16:22 +0200)]
Revert "sunxi: binman: Add U-Boot binary size check"

This reverts commit 819f1e081c527d2d02cdaeec0027384688cf5de0.

This check was introduced in order to cope with the size limitation we had
when we were still using the raw environment in MMC. However, this
introduces padding as well, which can result in an overly huge binary if
one wants to flash the environment to some other location.

Since we now have a FAT-based environment, this check is not so useful
anymore, so we can just drop it.

Cc: Andre Przywara <andre.przywara@arm.com>
Cc: Måns Rullgård <mans@mansr.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
6 years agoMerge tag 'arc-uart-updates-for-2018.07-rc1' of git://git.denx.de/u-boot-arc
Tom Rini [Thu, 24 May 2018 13:54:25 +0000 (09:54 -0400)]
Merge tag 'arc-uart-updates-for-2018.07-rc1' of git://git.denx.de/u-boot-arc

Add support for DEBUG_UART on ARC devboards

This required us to do 2 things:
 1) Insert a call to debug_uart_init() in early boot code
 2) Convert serial_arc to Kconfig

Once both items above are done we just patched defconfigs.

6 years agoMerge tag 'signed-rpi-next' of git://github.com/agraf/u-boot
Tom Rini [Thu, 24 May 2018 13:54:14 +0000 (09:54 -0400)]
Merge tag 'signed-rpi-next' of git://github.com/agraf/u-boot

Patch queue for rpi - 2018-05-24

Some minor fixes for the Raspberry Pi:

  - Fix SD writes on new sdhost controller
  - Sanitize default load addresses, allowing for better payload placement

6 years agoARC: Enable debug UART on nSIM boards
Alexey Brodkin [Mon, 21 May 2018 13:55:20 +0000 (16:55 +0300)]
ARC: Enable debug UART on nSIM boards

Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
6 years agoserial/serial_arc: Implement debug serial
Alexey Brodkin [Mon, 21 May 2018 13:42:07 +0000 (16:42 +0300)]
serial/serial_arc: Implement debug serial

Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
6 years agoserial: Convert ARC_SERIAL to Kconfig
Alexey Brodkin [Mon, 21 May 2018 13:40:05 +0000 (16:40 +0300)]
serial: Convert ARC_SERIAL to Kconfig

One step closer to completely Kconfig-driven target configuration in
U-Boot :)

Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
6 years agoARC: enable debug uart for HSDK and AXS10x boards
Eugeniy Paltsev [Thu, 3 May 2018 12:01:59 +0000 (15:01 +0300)]
ARC: enable debug uart for HSDK and AXS10x boards

Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
6 years agoARC: init debug uart in early common arc code
Eugeniy Paltsev [Thu, 3 May 2018 12:01:58 +0000 (15:01 +0300)]
ARC: init debug uart in early common arc code

The debug UART is intended for use very early in U-Boot to debug
problems before serial drivers are up.

Call debug_uart_init right before board_init_f.

Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
6 years agorpi: Change load addresses to make more room for the kernel & DTB
Tuomas Tynkkynen [Fri, 20 Apr 2018 10:03:49 +0000 (13:03 +0300)]
rpi: Change load addresses to make more room for the kernel & DTB

As of Linux 4.16, a multiplatform AArch64 kernel with our distro config
takes 26M. The current space reservation leaves only 17M for the kernel
and if it goes over it, the initrd gets overwritten when loading the
kernel from the filesystem.

A similar problem happens on ARMv7 with the DTBs taken from the
downstream Raspberry Pi foundation kernel. I guess they compile them
with DT overlay support enabled which grows them just enough.

Fix both of these problems by rewriting the memory map, which now allows
kernels to be up to 36M and DTBs up to 1M. Also the comment block was
kind of obsolete ever since the introduction of AArch64 support and the
firmware-loaded DTB doesn't get placed at 0x100 anymore either, so that
is fixed as well.

Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
6 years agospl: Add full fitImage support
Marek Vasut [Sat, 12 May 2018 22:23:17 +0000 (00:23 +0200)]
spl: Add full fitImage support

Add support for loading U-Boot and optionally FDT from a fitImage
in SPL by using the full fitImage support from U-Boot. While we do
have limited SPL loading support in SPL with a small footprint, it
is missing a lot of important features, like checking signatures.
This support has all the fitImage features, while the footprint is
obviously larger.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
6 years agopylibfdt: Add missing CC and LD to Makefile
Marek Vasut [Fri, 18 May 2018 07:56:53 +0000 (09:56 +0200)]
pylibfdt: Add missing CC and LD to Makefile

Add missing CC and LDSHARED variables to the Makefile to pass the
correct C compiler and linker path to the build of _libfdt.so .

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
6 years agoscripts: add decodecode from Linux
Heinrich Schuchardt [Tue, 15 May 2018 17:42:24 +0000 (19:42 +0200)]
scripts: add decodecode from Linux

The script decodecode can be used to disassemble the 'Code:' line  written
when an exception occurs.

The script is copied from Linux v4.16.

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
6 years agoarm: print instructions pointed to by pc
Heinrich Schuchardt [Tue, 15 May 2018 17:42:23 +0000 (19:42 +0200)]
arm: print instructions pointed to by pc

If an exception occurs in a loaded image and the relocation offset is
unknown, it is helful to know the instructions pointed to by the
program counter. This patch adds the missing output.

A possible output is:
    Code: e1c560d0 e12fff1e e120077b e12fff1e (e7f7defb)

The parentheses indicate the instruction causing the exception.

The output can be disassembled using the decodecode script provided
by the Linux kernel project.

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
6 years agoarm64: timer: Create timer_get_bootus for bootstage support
Michal Simek [Tue, 15 May 2018 14:47:02 +0000 (16:47 +0200)]
arm64: timer: Create timer_get_bootus for bootstage support

Implement timer_get_boot_us() based on available functions to support
bootstage command.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
6 years agoMakefile: adopt --std=gnu11 for HOSTCFLAGS on Linux
Philipp Tomsich [Mon, 14 May 2018 13:22:06 +0000 (15:22 +0200)]
Makefile: adopt --std=gnu11 for HOSTCFLAGS on Linux

Following the conversion of the SPDX license tags, a number of files
compiled with -pedantic now generate warnings similar to the following
for using C99-style '//' comments in ISO C90 code:

  tools/gen_eth_addr.c:1:1: warning: C++ style comments are not allowed in ISO C90
   // SPDX-License-Identifier: GPL-2.0+
   ^

The SPDX comment-style change means that these files have adopted C99,
so need to change the language-standard to --std=gnu99 or --std=gnu11
to let the compiler know this.

As we now require GCC 6 or newer for the cross-compiler, the project has
implicitly moved the project to GNU11: let older GCC versions on various
Linux distros know to treat our host tools as GNU11 as well.

References: commit 83d290c56fab ("SPDX: Convert all of our single license tags to Linux Kernel style")
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
6 years agotwister: Let SPL load U-Boot from MMC
Ladislav Michl [Mon, 14 May 2018 07:17:45 +0000 (09:17 +0200)]
twister: Let SPL load U-Boot from MMC

MMC is not initialized in SPL, so it cannot load u-boot.img
preventing boot from MMC.

Also driver specific functions are guarded with generic
configuration options which leads to build failures when device
driver is not enabled in config. Fix that by using driver
specific defines.

Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Acked-by: Stefano Babic <sbabic@denx.de>
6 years agofit: Add standalone image type handling
Marek Vasut [Sat, 12 May 2018 22:22:54 +0000 (00:22 +0200)]
fit: Add standalone image type handling

Just add IH_TYPE_STANDALONE to fit_get_image_type_property().

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
6 years agofit: Add empty fit_print_contents() and fit_image_print()
Marek Vasut [Sat, 12 May 2018 22:22:53 +0000 (00:22 +0200)]
fit: Add empty fit_print_contents() and fit_image_print()

These functions may be needed in SPL, so add empty variants of them
if CONFIG_SPL_FIT_PRINT is disabled.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
6 years agofit: Fix CONFIG_FIT_SPL_PRINT
Marek Vasut [Sat, 12 May 2018 22:22:52 +0000 (00:22 +0200)]
fit: Fix CONFIG_FIT_SPL_PRINT

Rename CONFIG_FIT_SPL_PRINT to CONFIG_SPL_FIT_PRINT and add Kconfig
entry for it.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
6 years agospl: fit: Add support for loading FPGA bitstream
Marek Vasut [Sat, 12 May 2018 20:25:28 +0000 (22:25 +0200)]
spl: fit: Add support for loading FPGA bitstream

Add support for loading FPGA into the SPL fitImage support. The
mechanism is flexible and allows user to override the actual
function for loading the FPGA itself. This is because on some
systems, the FPGA must be programmed to allow DRAM access, so
loading the full fitImage may not be possible if it contains
the bitstream. Instead, the spl_load_fpga_image() provides all
the tools to load the bitstream in parts while programming it
into the FPGA.

Signed-off-by: Marek Vasut <marex@denx.de>
[trini: Don't always have a branch to print out type]
Signed-off-by: Tom Rini <trini@konsulko.com>
6 years agobootcount: Add bootcount command
Alex Kiernan [Sat, 12 May 2018 05:49:47 +0000 (05:49 +0000)]
bootcount: Add bootcount command

Add a command to manipulate the bootcounter. This is useful if you can
run device recovery from inside U-Boot and need to reset the bootcounter
after executing that process as part of altbootcmd.

Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
6 years agoconfigs: sama5d2_xplained: fix bootcmd/args for spi+emmc demo
Eugen Hristev [Fri, 11 May 2018 08:14:32 +0000 (11:14 +0300)]
configs: sama5d2_xplained: fix bootcmd/args for spi+emmc demo

For sama5d2_xplained_spiflash_defconfig, we have the demo layout
as presented on this link:
http://www.at91.com/linux4sam/bin/view/Linux4SAM/Sama5d2XplainedMainPage#SPI_eMMC_Flash_demo_Memory_map

on SPI Flash (4 Mbyte) we have Bootstrap (second level bootloader), U-boot + env

and kernel+dtb we keep on eMMC on single partition in /boot directory, formatted
with ext4.

Thus, changing the boot command to reflect this demo for the spiflash config,
and fixing up bootargs. Sama5d2_xplained does not have NAND flash, so the
bootargs were completely wrong.

Fixes: "5abc1a45": common: Move CONFIG_BOOTARGS to Kconfig
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
6 years agoconfigs: sama5d2_xplained: set default FAT env location to SD-Card
Eugen Hristev [Fri, 11 May 2018 08:14:31 +0000 (11:14 +0300)]
configs: sama5d2_xplained: set default FAT env location to SD-Card

For sama5d2_xplained_mmc_defconfig, we have the following layout for SD-Card:
partition 1: FAT: contains bootstrap binary (second level bootloader),
U-boot, U-boot env, kernel, dtb
partition 2: EXT4: Rootfs.

Add to defconfig CONFIG_ENV_FAT_DEVICE_AND_PART to have environment
by default on SD-Card, to align with our demo layout.

Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
6 years agodoc: expand README.commands
Heinrich Schuchardt [Thu, 10 May 2018 13:57:27 +0000 (15:57 +0200)]
doc: expand README.commands

Describe U_BOOT_CMD_COMPLETE.
Describe the arguments of U_BOOT_CMD and U_BOOT_CMD_COMPLETE.
Describe the arguments of the command function.
Describe the arguments of the completion function.

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
6 years agotest: fs: fs-test: Modified test 1 to do a ls to a nonexistent dir
Eugen Hristev [Wed, 9 May 2018 13:28:38 +0000 (16:28 +0300)]
test: fs: fs-test: Modified test 1 to do a ls to a nonexistent dir

Added a simple ls to a nonexistent directory for test 1.
In case the driver is broken for a nonexistent directory, U-boot
might crash.

Here is an example failed output:

=> # Test Case 1 - ls
=> ext4ls host 0:0
<DIR>       4096 .
<DIR>       4096 ..
<DIR>      16384 lost+found
<DIR>       4096 SUBDIR
      2621440000 2.5GB.file
         1048576 1MB.file
=> # In addition, test with a nonexistent directory to see if we crash.
=> ext4ls host 0:0 invalid_d
** Can not find directory. **
./test/fs/fs-test.sh: line 161: 25786 Segmentation fault      (core dumped) $UBOOT  <<EOF

Subsequent tests will fail if U-boot crashes.

Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
6 years agofs: ext4: fix crash on ext4ls
Eugen Hristev [Wed, 9 May 2018 13:28:37 +0000 (16:28 +0300)]
fs: ext4: fix crash on ext4ls

Found a crash while issuing ext4ls with a non-existent directory.
Crash test:

=> ext4ls mmc 0 1
** Can not find directory. **
data abort
pc : [<3fd7c2ec>]          lr : [<3fd93ed8>]
reloc pc : [<26f142ec>]    lr : [<26f2bed8>]
sp : 3f963338  ip : 3fdc3dc4     fp : 3fd6b370
r10: 00000004  r9 : 3f967ec0     r8 : 3f96db68
r7 : 3fdc99b4  r6 : 00000000     r5 : 3f96dc88  r4 : 3fdcbc8c
r3 : fffffffa  r2 : 00000000     r1 : 3f96e0bc  r0 : 00000002
Flags: nZCv  IRQs off  FIQs off  Mode SVC_32
Resetting CPU ...

resetting ...

Tested on SAMA5D2_Xplained board (sama5d2_xplained_mmc_defconfig)

Looks like crash is introduced by commit:
"fa9ca8a" fs/ext4/ext4fs.c: Free dirnode in error path of ext4fs_ls

Issue is that dirnode is not initialized, and then freed if the call
to ext4_ls fails. ext4_ls will not change the value of dirnode in this case
thus we have a crash with data abort.

I added initialization and a check for dirname being NULL.

Fixes: "fa9ca8a" fs/ext4/ext4fs.c: Free dirnode in error path of ext4fs_ls
Cc: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Cc: Tom Rini <trini@konsulko.com>
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
6 years agoi2c: Drop CONFIG_SH_SH7734_I2C
Tuomas Tynkkynen [Wed, 9 May 2018 12:24:35 +0000 (15:24 +0300)]
i2c: Drop CONFIG_SH_SH7734_I2C

Last user of this driver went away in May 2017 in commit
eb5ba3aefdf0f6c ("i2c: Drop use of CONFIG_I2C_HARD").

Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
Acked-by: Heiko Schocher <hs@denx.de>
6 years agoi2c: Drop CONFIG_TSI108_I2C
Tuomas Tynkkynen [Wed, 9 May 2018 12:24:34 +0000 (15:24 +0300)]
i2c: Drop CONFIG_TSI108_I2C

Last user of this driver went away in June 2015 in commit
d928664f4101e24 ("powerpc: 74xx_7xx: remove 74xx_7xx cpu support")

Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
Acked-by: Heiko Schocher <hs@denx.de>
6 years agonet: Drop CONFIG_TSI108_ETH
Tuomas Tynkkynen [Wed, 9 May 2018 12:24:33 +0000 (15:24 +0300)]
net: Drop CONFIG_TSI108_ETH

Last user of this driver went away in June 2015 in commit
d928664f4101e24 ("powerpc: 74xx_7xx: remove 74xx_7xx cpu support")

Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
6 years agoconfigs: sama5d2_xplained: enable ext4 command support
Eugen Hristev [Wed, 9 May 2018 10:08:01 +0000 (13:08 +0300)]
configs: sama5d2_xplained: enable ext4 command support

To support loading the zImage + DTB from the rootfs ext4 partitions,
enable the ext4 command support.

Based on original work by Wenyou Yang

Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
6 years agoclk: at91: clk-h32mx: replace dm_warn with dev_dbg
Eugen Hristev [Wed, 9 May 2018 07:58:30 +0000 (10:58 +0300)]
clk: at91: clk-h32mx: replace dm_warn with dev_dbg

dm_warn is too noisy, replace with dev_dbg for less noise.

Based on original work by Wenyou Yang

Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
6 years agoconfigs: at91sam9x5ek: updated mtdparts variable in bootargs
Eugen Hristev [Wed, 9 May 2018 07:30:26 +0000 (10:30 +0300)]
configs: at91sam9x5ek: updated mtdparts variable in bootargs

We have a new demo layout of our sama5 boards for the NAND Flash
memory.
According to this new layout, adjust the mtdparts variable in bootargs
to align with this, which is available at :
http://www.at91.com/linux4sam/bin/view/Linux4SAM/Sama5d3XplainedMainPage#NAND_Flash_demo_Memory_map,

Based on original work by Wenyou Yang

Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
6 years agoconfigs: at91: Adjust CONFIG_ENV_OFFSET to match sama5 address
Nicolas Ferre [Wed, 9 May 2018 07:30:25 +0000 (10:30 +0300)]
configs: at91: Adjust CONFIG_ENV_OFFSET to match sama5 address

In order to have a single ENV_OFFSET to manage, use the same as the sama5 one.
This address matches our NAND flash map available at:
http://www.at91.com/linux4sam/bin/view/Linux4SAM/Sama5d3XplainedMainPage#NAND_Flash_demo_Memory_map

Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
[eugen.hristev@microchip.com: rework on latest version of u-boot]
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
6 years agoconfigs: at91: sama5_common: Adjust CONFIG_ENV_OFFSET to match block alignment
Nicolas Ferre [Wed, 9 May 2018 07:30:24 +0000 (10:30 +0300)]
configs: at91: sama5_common: Adjust CONFIG_ENV_OFFSET to match block alignment

Fix the unaligned environment address.
This address matches our NAND flash map available at:
http://www.at91.com/linux4sam/bin/view/Linux4SAM/Sama5d3XplainedMainPage#NAND_Flash_demo_Memory_map

Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
[eugen.hristev@microchip.com: rework on latest version of u-boot]
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
6 years agoFIT: Make fit_conf_print() be a static function
Tom Rini [Tue, 8 May 2018 18:34:05 +0000 (14:34 -0400)]
FIT: Make fit_conf_print() be a static function

We only call fit_conf_print from one place in the code, so mark it as
static and move it up to where we call it.  This in turn has us move a
few other already static functions up further as well.

Signed-off-by: Tom Rini <trini@konsulko.com>
6 years agoLicenses/README: Update some style and add explicit license to the document
Tom Rini [Tue, 8 May 2018 15:34:36 +0000 (11:34 -0400)]
Licenses/README: Update some style and add explicit license to the document

- Add an SPDX license tag to the file, saying it's GPL-2.0.
- From the Linux Kernel v4.17-rc4, import the "License identifier
  syntax" section as-is from Documentation/process/license-rules.rst
  and then change it to be clearer about examples from the Linux Kernel
  vs examples found in U-Boot, and when we're talking about U-Boot.

Signed-off-by: Tom Rini <trini@konsulko.com>
6 years agoConvert CONFIG_SUPPORT_EMMC_RPMB to Kconfig
Alex Kiernan [Tue, 8 May 2018 04:43:31 +0000 (04:43 +0000)]
Convert CONFIG_SUPPORT_EMMC_RPMB to Kconfig

Convert CONFIG_SUPPORT_EMMC_RPMB to Kconfig. Split the command handling
from the underlying support and expose this through CMD_MMC_RPMB.

Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
6 years agommc: Unirqify bcm2835_sdhost and fix writes
Alexander Graf [Wed, 23 May 2018 20:24:51 +0000 (22:24 +0200)]
mmc: Unirqify bcm2835_sdhost and fix writes

The bcm2835 sdhost driver has a problem with "write multiple" commands.
It seems to boil down to the fact that the controller dislikes its FIFO
to get drained at the end of a block when a write multiple blocks command
is in flight.

The easy fix is to simply get rid of all the IRQ driven logic and make
the driver push as much data into the FIFO as it can. That way we never
drain and we never run into the problem.

Reported-by: Jan Leonhardt <jan@cyberdesigner.net>
Signed-off-by: Alexander Graf <agraf@suse.de>
6 years agorpi: Adjust fdt_addr_r to a sane address
Alexander Graf [Fri, 13 Apr 2018 15:37:34 +0000 (17:37 +0200)]
rpi: Adjust fdt_addr_r to a sane address

Back in the old days, 0x100 was used as the address to pass the device tree
from firmware into the kernel. This has since changed to a more dynamic
location, so using 0x100 actually breaks more things than it helps with.

Let's move the device tree default location for distro boot to a more sane
place that gives us enough head room in low memory.

Reported-by: Tuomas Tynkkynen <tuomas@tuxera.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
6 years agoarm: armv7m: Clean up some thumb / compiler flag options
Tom Rini [Tue, 8 May 2018 00:46:52 +0000 (20:46 -0400)]
arm: armv7m: Clean up some thumb / compiler flag options

- The correct way to build with thumb mode is to select SYS_THUMB_BUILD
- We should be setting -march=armv7-m in arch/arm/Makefile not the
  sub-config.mk file.

Signed-off-by: Tom Rini <trini@konsulko.com>
6 years ago.travis.yml: Further optimizations
Tom Rini [Thu, 10 May 2018 11:15:54 +0000 (07:15 -0400)]
.travis.yml: Further optimizations

- Xilinx aarch64 is caught in the general xilinx arm job, exclude from
  the general aarch64 job.
- Give the generic aarch64 job a better name
- Re-sort the PowerPC jobs so that we can complete them a bit quicker.

Signed-off-by: Tom Rini <trini@konsulko.com>
6 years agobuildman: support newer gcc versions from kernel.org
Daniel Schwierzeck [Thu, 10 May 2018 11:15:53 +0000 (07:15 -0400)]
buildman: support newer gcc versions from 

Add support for gcc versions 7.3.0, 6.4.0 and 4.9.4.

Also use a regex for matching the tarball names. Some gcc versions
use '-ARCH-' instead of '_ARCH-'.

As part of this, we switch TravisCI to also using these toolchains for
all platforms.

Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
6 years agoat91: Minor tweaks to SPL logic for space savings on smartweb
Tom Rini [Thu, 10 May 2018 11:15:52 +0000 (07:15 -0400)]
at91: Minor tweaks to SPL logic for space savings on smartweb

- spl_board_init is empty on smartweb so drop that function
- When CONFIG_AT91SAM9_WATCHDOG is set we do not disable the watchdog in
  SPL and instead let full U-Boot handle it.  Instead of an empty
  function just do not call a function.

Signed-off-by: Tom Rini <trini@konsulko.com>
6 years agoMerge branch 'master' of git://git.denx.de/u-boot-uniphier
Tom Rini [Tue, 22 May 2018 17:53:26 +0000 (13:53 -0400)]
Merge branch 'master' of git://git.denx.de/u-boot-uniphier

6 years agoARM: dts: uniphier: sync with Linux 4.17-rc6
Masahiro Yamada [Tue, 22 May 2018 15:30:54 +0000 (00:30 +0900)]
ARM: dts: uniphier: sync with Linux 4.17-rc6

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
6 years agoARM: uniphier: rename environment variable fdt_file to fdtfile
Masahiro Yamada [Thu, 17 May 2018 10:55:20 +0000 (19:55 +0900)]
ARM: uniphier: rename environment variable fdt_file to fdtfile

For booting Linux in the generic distro mechanism, cmd/pxe.c
retrieves the FDT file name from "fdtfile" environment variable.

Rename "fdt_file" to "fdtfile" for easier migration to distro boot.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
6 years agoARM: dts: uniphier: change phy-mode to 'internal' for LD11
Kunihiko Hayashi [Fri, 11 May 2018 09:49:17 +0000 (18:49 +0900)]
ARM: dts: uniphier: change phy-mode to 'internal' for LD11

Change the phy-mode property to 'internal' that means to use a built-in PHY
implemented on LD11 SoC.

Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
6 years agoARM: dts: uniphier: add clock-names and reset-names to ethernet node
Kunihiko Hayashi [Fri, 11 May 2018 09:49:16 +0000 (18:49 +0900)]
ARM: dts: uniphier: add clock-names and reset-names to ethernet node

Add clock-names and reset-names because this node recognizes multiple
clocks and resets.  ("ether", and so on, for each)

Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
6 years agoARM: dts: uniphier: add required clocks and resets to Pro4 ethernet node
Kunihiko Hayashi [Fri, 11 May 2018 09:49:15 +0000 (18:49 +0900)]
ARM: dts: uniphier: add required clocks and resets to Pro4 ethernet node

The GIO clock/reset, another MAC clock, and the PHY clock are required
for the ethernet of Pro4 SoC.

Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
6 years agoARM: dts: uniphier: add syscon-phy-mode property to each ethernet node
Kunihiko Hayashi [Fri, 11 May 2018 09:49:14 +0000 (18:49 +0900)]
ARM: dts: uniphier: add syscon-phy-mode property to each ethernet node

Add syscon-phy-mode property specifying a phandle of system controller
to each ethernet node.

Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
6 years agoSPDX: Fixup SPDX tags in a few new files
Tom Rini [Sun, 20 May 2018 13:47:45 +0000 (09:47 -0400)]
SPDX: Fixup SPDX tags in a few new files

Signed-off-by: Tom Rini <trini@konsulko.com>
6 years agoMerge branch 'master' of git://git.denx.de/u-boot-sh
Tom Rini [Sun, 20 May 2018 13:44:38 +0000 (09:44 -0400)]
Merge branch 'master' of git://git.denx.de/u-boot-sh

6 years agoMerge branch 'master' of git://git.denx.de/u-boot-usb
Tom Rini [Sun, 20 May 2018 13:44:13 +0000 (09:44 -0400)]
Merge branch 'master' of git://git.denx.de/u-boot-usb

6 years agoMerge branch 'master' of git://git.denx.de/u-boot-socfpga
Tom Rini [Sun, 20 May 2018 13:44:05 +0000 (09:44 -0400)]
Merge branch 'master' of git://git.denx.de/u-boot-socfpga

6 years agoARM: rmobile: Unify Gen2 Makefile entry
Marek Vasut [Wed, 2 May 2018 10:09:23 +0000 (12:09 +0200)]
ARM: rmobile: Unify Gen2 Makefile entry

Drop per-SoC Makefile entries and replace them with one unified entry
now that the PFC tables are gone. Shuffle the Makefile around a bit
to make it more organized.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
6 years agoARM: rmobile: Drop old R8A7794 PFC tables
Marek Vasut [Wed, 2 May 2018 10:07:45 +0000 (12:07 +0200)]
ARM: rmobile: Drop old R8A7794 PFC tables

All the boards use new modern PFC framework, the old PFC tables
are no longer used, so remove them.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
6 years agoARM: rmobile: Drop old R8A7793 PFC tables
Marek Vasut [Wed, 2 May 2018 10:07:18 +0000 (12:07 +0200)]
ARM: rmobile: Drop old R8A7793 PFC tables

All the boards use new modern PFC framework, the old PFC tables
are no longer used, so remove them.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
6 years agoARM: rmobile: Drop old R8A7792 PFC tables
Marek Vasut [Wed, 2 May 2018 10:06:48 +0000 (12:06 +0200)]
ARM: rmobile: Drop old R8A7792 PFC tables

All the boards use new modern PFC framework, the old PFC tables
are no longer used, so remove them.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
6 years agoARM: rmobile: Drop old R8A7791 PFC tables
Marek Vasut [Wed, 2 May 2018 10:06:08 +0000 (12:06 +0200)]
ARM: rmobile: Drop old R8A7791 PFC tables

All the boards use new modern PFC framework, the old PFC tables
are no longer used, so remove them.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
6 years agoARM: rmobile: Drop old R8A7790 PFC tables
Marek Vasut [Wed, 2 May 2018 10:05:08 +0000 (12:05 +0200)]
ARM: rmobile: Drop old R8A7790 PFC tables

All the boards use new modern PFC framework, the old PFC tables
are no longer used, so remove them.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
6 years agoARM: rmobile: Update V2H Blanche
Marek Vasut [Mon, 30 Apr 2018 12:10:36 +0000 (14:10 +0200)]
ARM: rmobile: Update V2H Blanche

The V2H Blanche port was broken since some time. This patch updates
the V2H Blanche port to use modern frameworks, DM, DT probing, SPL
for the preloading and puts it on par with the M2 Porter board.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
6 years agoARM: rmobile: Enable DM capable RCar I2C driver on Silk
Marek Vasut [Tue, 1 May 2018 06:57:25 +0000 (08:57 +0200)]
ARM: rmobile: Enable DM capable RCar I2C driver on Silk

Enable the DM capable driver instead of the legacy one.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
6 years agoARM: rmobile: Enable DM capable RCar I2C driver on Lager
Marek Vasut [Tue, 1 May 2018 06:57:20 +0000 (08:57 +0200)]
ARM: rmobile: Enable DM capable RCar I2C driver on Lager

Enable the DM capable driver instead of the legacy one.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
6 years agoi2c: rcar_i2c: Add DM and DT capable I2C driver
Marek Vasut [Sat, 21 Apr 2018 16:57:28 +0000 (18:57 +0200)]
i2c: rcar_i2c: Add DM and DT capable I2C driver

Add derivative of the rcar_i2c driver which is capable of
probing itself from DM and uses DT.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>