Felix Fietkau [Mon, 30 Jul 2018 18:31:28 +0000 (21:31 +0300)]
ath9k_hw: fix channel maximum power level test
[ Upstream commit
461d8a6bb9879b0e619752d040292e67aa06f1d2 ]
The tx power applied by set_txpower is limited by the CTL (conformance
test limit) entries in the EEPROM. These can change based on the user
configured regulatory domain.
Depending on the EEPROM data this can cause the tx power to become too
limited, if the original regdomain CTLs impose lower limits than the CTLs
of the user configured regdomain.
To fix this issue, set the initial channel limits without any CTL
restrictions and only apply the CTL at run time when setting the channel
and the real tx power.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Felix Fietkau [Mon, 30 Jul 2018 18:31:23 +0000 (21:31 +0300)]
ath9k: report tx status on EOSP
[ Upstream commit
36e14a787dd0b459760de3622e9709edb745a6af ]
Fixes missed indications of end of U-APSD service period to mac80211
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Finn Thain [Mon, 2 Jul 2018 08:21:18 +0000 (04:21 -0400)]
macintosh/via-pmu: Add missing mmio accessors
[ Upstream commit
576d5290d678a651b9f36050fc1717e0573aca13 ]
Add missing in_8() accessors to init_pmu() and pmu_sr_intr().
This fixes several sparse warnings:
drivers/macintosh/via-pmu.c:536:29: warning: dereference of noderef expression
drivers/macintosh/via-pmu.c:537:33: warning: dereference of noderef expression
drivers/macintosh/via-pmu.c:1455:17: warning: dereference of noderef expression
drivers/macintosh/via-pmu.c:1456:69: warning: dereference of noderef expression
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Kan Liang [Mon, 9 Jul 2018 14:15:22 +0000 (07:15 -0700)]
perf evlist: Fix error out while applying initial delay and LBR
[ Upstream commit
95035c5e167ae6e740b1ddd30210ae0eaf39a5db ]
'perf record' will error out if both --delay and LBR are applied.
For example:
# perf record -D 1000 -a -e cycles -j any -- sleep 2
Error:
dummy:HG: PMU Hardware doesn't support sampling/overflow-interrupts.
Try 'perf stat'
#
A dummy event is added implicitly for initial delay, which has the same
configurations as real sampling events. The dummy event is a software
event. If LBR is configured, perf must error out.
The dummy event will only be used to track PERF_RECORD_MMAP while perf
waits for the initial delay to enable the real events. The BRANCH_STACK
bit can be safely cleared for the dummy event.
After applying the patch:
# perf record -D 1000 -a -e cycles -j any -- sleep 2
[ perf record: Woken up 1 times to write data ]
[ perf record: Captured and wrote 1.054 MB perf.data (828 samples) ]
#
Reported-by: Sunil K Pandey <sunil.k.pandey@intel.com>
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1531145722-16404-1-git-send-email-kan.liang@linux.intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jiri Olsa [Tue, 24 Jul 2018 06:20:08 +0000 (08:20 +0200)]
perf c2c report: Fix crash for empty browser
[ Upstream commit
73978332572ccf5e364c31e9a70ba953f8202b46 ]
'perf c2c' scans read/write accesses and tries to find false sharing
cases, so when the events it wants were not asked for or ended up not
taking place, we get no histograms.
So do not try to display entry details if there's not any. Currently
this ends up in crash:
$ perf c2c report # then press 'd'
perf: Segmentation fault
$
Committer testing:
Before:
Record a perf.data file without events of interest to 'perf c2c report',
then call it and press 'd':
# perf record sleep 1
[ perf record: Woken up 1 times to write data ]
[ perf record: Captured and wrote 0.001 MB perf.data (6 samples) ]
# perf c2c report
perf: Segmentation fault
-------- backtrace --------
perf[0x5b1d2a]
/lib64/libc.so.6(+0x346df)[0x7fcb566e36df]
perf[0x46fcae]
perf[0x4a9f1e]
perf[0x4aa220]
perf(main+0x301)[0x42c561]
/lib64/libc.so.6(__libc_start_main+0xe9)[0x7fcb566cff29]
perf(_start+0x29)[0x42c999]
#
After the patch the segfault doesn't take place, a follow up patch to
tell the user why nothing changes when 'd' is pressed would be good.
Reported-by: rodia@autistici.org
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Don Zickus <dzickus@redhat.com>
Cc: Joe Mario <jmario@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Fixes:
f1c5fd4d0bb9 ("perf c2c report: Add TUI cacheline browser")
Link: http://lkml.kernel.org/r/20180724062008.26126-1-jolsa@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Olga Kornievskaia [Thu, 26 Jul 2018 20:04:47 +0000 (16:04 -0400)]
NFSv4.0 fix client reference leak in callback
[ Upstream commit
32cd3ee511f4e07ca25d71163b50e704808d22f4 ]
If there is an error during processing of a callback message, it leads
to refrence leak on the client structure and eventually an unclean
superblock.
Signed-off-by: Olga Kornievskaia <kolga@netapp.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Christophe Leroy [Fri, 22 Sep 2017 11:20:43 +0000 (13:20 +0200)]
perf tools: Allow overriding MAX_NR_CPUS at compile time
[ Upstream commit
21b8732eb4479b579bda9ee38e62b2c312c2a0e5 ]
After update of kernel, the perf tool doesn't run anymore on my 32MB RAM
powerpc board, but still runs on a 128MB RAM board:
~# strace perf
execve("/usr/sbin/perf", ["perf"], [/* 12 vars */]) = -1 ENOMEM (Cannot allocate memory)
--- SIGSEGV {si_signo=SIGSEGV, si_code=SI_KERNEL, si_addr=0} ---
+++ killed by SIGSEGV +++
Segmentation fault
objdump -x shows that .bss section has a huge size of 24Mbytes:
27 .bss
016baca8 101cebb8 101cebb8 001cd988 2**3
With especially the following objects having quite big size:
10205f80 l O .bss
00140000 runtime_cycles_stats
10345f80 l O .bss
00140000 runtime_stalled_cycles_front_stats
10485f80 l O .bss
00140000 runtime_stalled_cycles_back_stats
105c5f80 l O .bss
00140000 runtime_branches_stats
10705f80 l O .bss
00140000 runtime_cacherefs_stats
10845f80 l O .bss
00140000 runtime_l1_dcache_stats
10985f80 l O .bss
00140000 runtime_l1_icache_stats
10ac5f80 l O .bss
00140000 runtime_ll_cache_stats
10c05f80 l O .bss
00140000 runtime_itlb_cache_stats
10d45f80 l O .bss
00140000 runtime_dtlb_cache_stats
10e85f80 l O .bss
00140000 runtime_cycles_in_tx_stats
10fc5f80 l O .bss
00140000 runtime_transaction_stats
11105f80 l O .bss
00140000 runtime_elision_stats
11245f80 l O .bss
00140000 runtime_topdown_total_slots
11385f80 l O .bss
00140000 runtime_topdown_slots_retired
114c5f80 l O .bss
00140000 runtime_topdown_slots_issued
11605f80 l O .bss
00140000 runtime_topdown_fetch_bubbles
11745f80 l O .bss
00140000 runtime_topdown_recovery_bubbles
This is due to commit
4d255766d28b1 ("perf: Bump max number of cpus
to 1024"), because many tables are sized with MAX_NR_CPUS
This patch gives the opportunity to redefine MAX_NR_CPUS via
$ make EXTRA_CFLAGS=-DMAX_NR_CPUS=1
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: linuxppc-dev@lists.ozlabs.org
Link: http://lkml.kernel.org/r/20170922112043.8349468C57@po15668-vm-win7.idsi0.si.c-s.fr
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Randy Dunlap [Sat, 7 Jul 2018 03:50:57 +0000 (20:50 -0700)]
f2fs: fix defined but not used build warnings
[ Upstream commit
cb15d1e43db0a6341c1e26ac6a2c74e61b74f1aa ]
Fix build warnings in f2fs when CONFIG_PROC_FS is not enabled
by marking the unused functions as __maybe_unused.
../fs/f2fs/sysfs.c:519:12: warning: 'segment_info_seq_show' defined but not used [-Wunused-function]
../fs/f2fs/sysfs.c:546:12: warning: 'segment_bits_seq_show' defined but not used [-Wunused-function]
../fs/f2fs/sysfs.c:570:12: warning: 'iostat_info_seq_show' defined but not used [-Wunused-function]
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Jaegeuk Kim <jaegeuk@kernel.org>
Cc: Chao Yu <yuchao0@huawei.com>
Cc: linux-f2fs-devel@lists.sourceforge.net
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Yunlong Song [Thu, 12 Jul 2018 15:09:26 +0000 (23:09 +0800)]
f2fs: do not set free of current section
[ Upstream commit
3611ce9911267cb93d364bd71ddea6821278d11f ]
For the case when sbi->segs_per_sec > 1, take section:segment = 5 for
example, if segment 1 is just used and allocate new segment 2, and the
blocks of segment 1 is invalidated, at this time, the previous code will
use __set_test_and_free to free the free_secmap and free_sections++,
this is not correct since it is still a current section, so fix it.
Signed-off-by: Yunlong Song <yunlong.song@huawei.com>
Reviewed-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Chao Yu [Fri, 27 Jul 2018 10:15:14 +0000 (18:15 +0800)]
f2fs: fix to active page in lru list for read path
[ Upstream commit
82cf4f132e6d16dca6fc3bd955019246141bc645 ]
If config CONFIG_F2FS_FAULT_INJECTION is on, for both read or write path
we will call find_lock_page() to get the page, but for read path, it
missed to passing FGP_ACCESSED to allocator to active the page in LRU
list, result in being reclaimed in advance incorrectly, fix it.
Reported-by: Xianrong Zhou <zhouxianrong@huawei.com>
Signed-off-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Anton Vasilyev [Fri, 27 Jul 2018 13:39:31 +0000 (16:39 +0300)]
tty: rocket: Fix possible buffer overwrite on register_PCI
[ Upstream commit
0419056ec8fd01ddf5460d2dba0491aad22657dd ]
If number of isa and pci boards exceed NUM_BOARDS on the path
rp_init()->init_PCI()->register_PCI() then buffer overwrite occurs
in register_PCI() on assign rcktpt_io_addr[i].
The patch adds check on upper bound for index of registered
board in register_PCI.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Anton Vasilyev <vasilyev@ispras.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Michael Kelley [Thu, 2 Aug 2018 03:08:25 +0000 (03:08 +0000)]
Drivers: hv: vmbus: Cleanup synic memory free path
[ Upstream commit
572086325ce9a9e348b8748e830653f3959e88b6 ]
clk_evt memory is not being freed when the synic is shutdown
or when there is an allocation error. Add the appropriate
kfree() call, along with a comment to clarify how the memory
gets freed after an allocation error. Make the free path
consistent by removing checks for NULL since kfree() and
free_page() already do the check.
Signed-off-by: Michael Kelley <mikelley@microsoft.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Anton Vasilyev [Tue, 24 Jul 2018 15:10:38 +0000 (18:10 +0300)]
firmware: vpd: Fix section enabled flag on vpd_section_destroy
[ Upstream commit
45ca3f76de0507ecf143f770570af2942f263812 ]
static struct ro_vpd and rw_vpd are initialized by vpd_sections_init()
in vpd_probe() based on header's ro and rw sizes.
In vpd_remove() vpd_section_destroy() performs deinitialization based
on enabled flag, which is set to true by vpd_sections_init().
This leads to call of vpd_section_destroy() on already destroyed section
for probe-release-probe-release sequence if first probe performs
ro_vpd initialization and second probe does not initialize it.
The patch adds changing enabled flag on vpd_section_destroy and adds
cleanup on the error path of vpd_sections_init.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Anton Vasilyev <vasilyev@ispras.ru>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dan Carpenter [Thu, 2 Aug 2018 08:24:47 +0000 (11:24 +0300)]
uio: potential double frees if __uio_register_device() fails
[ Upstream commit
f019f07ecf6a6b8bd6d7853bce70925d90af02d1 ]
The uio_unregister_device() function assumes that if "info->uio_dev" is
non-NULL that means "info" is fully allocated. Setting info->uio_de
has to be the last thing in the function.
In the current code, if request_threaded_irq() fails then we return with
info->uio_dev set to non-NULL but info is not fully allocated and it can
lead to double frees.
Fixes:
beafc54c4e2f ("UIO: Add the User IO core code")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Anton Vasilyev [Fri, 27 Jul 2018 15:45:36 +0000 (18:45 +0300)]
misc: ti-st: Fix memory leak in the error path of probe()
[ Upstream commit
81ae962d7f180c0092859440c82996cccb254976 ]
Free resources instead of direct return of the error code if kim_probe
fails.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Anton Vasilyev <vasilyev@ispras.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Philipp Zabel [Thu, 21 Jun 2018 19:13:38 +0000 (21:13 +0200)]
gpu: ipu-v3: default to id 0 on missing OF alias
[ Upstream commit
2d87e6c1b99c402360fdfe19ce4f579ab2f96adf ]
This is better than storing -ENODEV in the id number. This fixes SoCs
with only one IPU that don't specify an IPU alias in the device tree.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Todor Tomov [Wed, 25 Jul 2018 16:38:20 +0000 (12:38 -0400)]
media: camss: csid: Configure data type and decode format properly
[ Upstream commit
c628e78899ff8006b5f9d8206da54ed3bb994342 ]
The CSID decodes the input data stream. When the input comes from
the Test Generator the format of the stream is set on the source
media pad. When the input comes from the CSIPHY the format is the
one on the sink media pad. Use the proper format for each case.
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Gaurav Kohli [Thu, 2 Aug 2018 08:51:03 +0000 (14:21 +0530)]
timers: Clear timer_base::must_forward_clk with timer_base::lock held
[ Upstream commit
363e934d8811d799c88faffc5bfca782fd728334 ]
timer_base::must_forward_clock is indicating that the base clock might be
stale due to a long idle sleep.
The forwarding of the base clock takes place in the timer softirq or when a
timer is enqueued to a base which is idle. If the enqueue of timer to an
idle base happens from a remote CPU, then the following race can happen:
CPU0 CPU1
run_timer_softirq mod_timer
base = lock_timer_base(timer);
base->must_forward_clk = false
if (base->must_forward_clk)
forward(base); -> skipped
enqueue_timer(base, timer, idx);
-> idx is calculated high due to
stale base
unlock_timer_base(timer);
base = lock_timer_base(timer);
forward(base);
The root cause is that timer_base::must_forward_clk is cleared outside the
timer_base::lock held region, so the remote queuing CPU observes it as
cleared, but the base clock is still stale. This can cause large
granularity values for timers, i.e. the accuracy of the expiry time
suffers.
Prevent this by clearing the flag with timer_base::lock held, so that the
forwarding takes place before the cleared flag is observable by a remote
CPU.
Signed-off-by: Gaurav Kohli <gkohli@codeaurora.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: john.stultz@linaro.org
Cc: sboyd@kernel.org
Cc: linux-arm-msm@vger.kernel.org
Link: https://lkml.kernel.org/r/1533199863-22748-1-git-send-email-gkohli@codeaurora.org
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
BingJing Chang [Wed, 1 Aug 2018 09:08:36 +0000 (17:08 +0800)]
md/raid5: fix data corruption of replacements after originals dropped
[ Upstream commit
d63e2fc804c46e50eee825c5d3a7228e07048b47 ]
During raid5 replacement, the stripes can be marked with R5_NeedReplace
flag. Data can be read from being-replaced devices and written to
replacing spares without reading all other devices. (It's 'replace'
mode. s.replacing = 1) If a being-replaced device is dropped, the
replacement progress will be interrupted and resumed with pure recovery
mode. However, existing stripes before being interrupted cannot read
from the dropped device anymore. It prints lots of WARN_ON messages.
And it results in data corruption because existing stripes write
problematic data into its replacement device and update the progress.
\# Erase disks (1MB + 2GB)
dd if=/dev/zero of=/dev/sda bs=1MB count=2049
dd if=/dev/zero of=/dev/sdb bs=1MB count=2049
dd if=/dev/zero of=/dev/sdc bs=1MB count=2049
dd if=/dev/zero of=/dev/sdd bs=1MB count=2049
mdadm -C /dev/md0 -amd -R -l5 -n3 -x0 /dev/sd[abc] -z 2097152
\# Ensure array stores non-zero data
dd if=/root/data_4GB.iso of=/dev/md0 bs=1MB
\# Start replacement
mdadm /dev/md0 -a /dev/sdd
mdadm /dev/md0 --replace /dev/sda
Then, Hot-plug out /dev/sda during recovery, and wait for recovery done.
echo check > /sys/block/md0/md/sync_action
cat /sys/block/md0/md/mismatch_cnt # it will be greater than 0.
Soon after you hot-plug out /dev/sda, you will see many WARN_ON
messages. The replacement recovery will be interrupted shortly. After
the recovery finishes, it will result in data corruption.
Actually, it's just an unhandled case of replacement. In commit
<
f94c0b6658c7> (md/raid5: fix interaction of 'replace' and 'recovery'.),
if a NeedReplace device is not UPTODATE then that is an error, the
commit just simply print WARN_ON but also mark these corrupted stripes
with R5_WantReplace. (it means it's ready for writes.)
To fix this case, we can leverage 'sync and replace' mode mentioned in
commit <
9a3e1101b827> (md/raid5: detect and handle replacements during
recovery.). We can add logics to detect and use 'sync and replace' mode
for these stripes.
Reported-by: Alex Chen <alexchen@synology.com>
Reviewed-by: Alex Wu <alexwu@synology.com>
Reviewed-by: Chung-Chiang Cheng <cccheng@synology.com>
Signed-off-by: BingJing Chang <bingjingc@synology.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mike Christie [Thu, 2 Aug 2018 17:12:20 +0000 (12:12 -0500)]
scsi: target: fix __transport_register_session locking
[ Upstream commit
6a64f6e1591322beb8ce16e952a53582caf2a15c ]
When __transport_register_session is called from transport_register_session
irqs will already have been disabled, so we do not want the unlock irq call
to enable them until the higher level has done the final
spin_unlock_irqrestore/ spin_unlock_irq.
This has __transport_register_session use the save/restore call.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Reviewed-by: Bart Van Assche <bart.vanassche@wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ming Lei [Thu, 2 Aug 2018 10:23:26 +0000 (18:23 +0800)]
blk-mq: fix updating tags depth
[ Upstream commit
75d6e175fc511e95ae3eb8f708680133bc211ed3 ]
The passed 'nr' from userspace represents the total depth, meantime
inside 'struct blk_mq_tags', 'nr_tags' stores the total tag depth,
and 'nr_reserved_tags' stores the reserved part.
There are two issues in blk_mq_tag_update_depth() now:
1) for growing tags, we should have used the passed 'nr', and keep the
number of reserved tags not changed.
2) the passed 'nr' should have been used for checking against
'tags->nr_tags', instead of number of the normal part.
This patch fixes the above two cases, and avoids kernel crash caused
by wrong resizing sbitmap queue.
Cc: "Ewan D. Milne" <emilne@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Omar Sandoval <osandov@fb.com>
Tested by: Marco Patalano <mpatalan@redhat.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Arun Parameswaran [Thu, 2 Aug 2018 00:53:47 +0000 (17:53 -0700)]
net: phy: Fix the register offsets in Broadcom iProc mdio mux driver
[ Upstream commit
77fefa93bfebe4df44f154f2aa5938e32630d0bf ]
Modify the register offsets in the Broadcom iProc mdio mux to start
from the top of the register address space.
Earlier, the base address pointed to the end of the block's register
space. The base address will now point to the start of the mdio's
address space. The offsets have been fixed to match this.
Signed-off-by: Arun Parameswaran <arun.parameswaran@broadcom.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Anton Vasilyev [Mon, 23 Jul 2018 17:04:54 +0000 (13:04 -0400)]
media: dw2102: Fix memleak on sequence of probes
[ Upstream commit
299c7007e93645067e1d2743f4e50156de78c4ff ]
Each call to dw2102_probe() allocates memory by kmemdup for structures
p1100, s660, p7500 and s421, but there is no their deallocation.
dvb_usb_device_init() copies the corresponding structure into
dvb_usb_device->props, so there is no use of original structure after
dvb_usb_device_init().
The patch moves structures from global scope to local and adds their
deallocation.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Anton Vasilyev <vasilyev@ispras.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Anton Vasilyev [Fri, 27 Jul 2018 11:52:20 +0000 (07:52 -0400)]
media: davinci: vpif_display: Mix memory leak on probe error path
[ Upstream commit
61e641f36ed81ae473177c085f0bfd83ad3b55ed ]
If vpif_probe() fails on v4l2_device_register() then memory allocated
at initialize_vpif() for global vpif_obj.dev[i] become unreleased.
The patch adds deallocation of vpif_obj.dev[i] on the error path and
removes duplicated check on platform_data presence.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Anton Vasilyev <vasilyev@ispras.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Roman Gushchin [Thu, 2 Aug 2018 22:47:10 +0000 (15:47 -0700)]
selftests/bpf: fix a typo in map in map test
[ Upstream commit
0069fb854364da79fd99236ea620affc8e1152d5 ]
Commit
fbeb1603bf4e ("bpf: verifier: MOV64 don't mark dst reg unbounded")
revealed a typo in commit
fb30d4b71214 ("bpf: Add tests for map-in-map"):
BPF_MOV64_REG(BPF_REG_0, 0) was used instead of
BPF_MOV64_IMM(BPF_REG_0, 0).
I've noticed the problem by running bpf kselftests.
Fixes:
fb30d4b71214 ("bpf: Add tests for map-in-map")
Signed-off-by: Roman Gushchin <guro@fb.com>
Cc: Martin KaFai Lau <kafai@fb.com>
Cc: Arthur Fabre <afabre@cloudflare.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Alexei Starovoitov <ast@kernel.org>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reza Arbab [Fri, 3 Aug 2018 04:03:36 +0000 (23:03 -0500)]
powerpc/powernv: Fix concurrency issue with npu->mmio_atsd_usage
[ Upstream commit
9eab9901b015f489199105c470de1ffc337cfabb ]
We've encountered a performance issue when multiple processors stress
{get,put}_mmio_atsd_reg(). These functions contend for
mmio_atsd_usage, an unsigned long used as a bitmask.
The accesses to mmio_atsd_usage are done using test_and_set_bit_lock()
and clear_bit_unlock(). As implemented, both of these will require
a (successful) stwcx to that same cache line.
What we end up with is thread A, attempting to unlock, being slowed by
other threads repeatedly attempting to lock. A's stwcx instructions
fail and retry because the memory reservation is lost every time a
different thread beats it to the punch.
There may be a long-term way to fix this at a larger scale, but for
now resolve the immediate problem by gating our call to
test_and_set_bit_lock() with one to test_bit(), which is obviously
implemented without using a store.
Fixes:
1ab66d1fbada ("powerpc/powernv: Introduce address translation services for Nvlink2")
Signed-off-by: Reza Arbab <arbab@linux.ibm.com>
Acked-by: Alistair Popple <alistair@popple.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dmitry Osipenko [Thu, 2 Aug 2018 11:11:44 +0000 (14:11 +0300)]
gpio: tegra: Move driver registration to subsys_init level
[ Upstream commit
40b25bce0adbe641a744d1291bc0e51fb7f3c3d8 ]
There is a bug in regards to deferred probing within the drivers core
that causes GPIO-driver to suspend after its users. The bug appears if
GPIO-driver probe is getting deferred, which happens after introducing
dependency on PINCTRL-driver for the GPIO-driver by defining "gpio-ranges"
property in device-tree. The bug in the drivers core is old (more than 4
years now) and is well known, unfortunately there is no easy fix for it.
The good news is that we can workaround the deferred probe issue by
changing GPIO / PINCTRL drivers registration order and hence by moving
PINCTRL driver registration to the arch_init level and GPIO to the
subsys_init.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan Hedberg [Sat, 4 Aug 2018 20:40:26 +0000 (23:40 +0300)]
Bluetooth: h5: Fix missing dependency on BT_HCIUART_SERDEV
[ Upstream commit
6c3711ec64fd23a9abc8aaf59a9429569a6282df ]
This driver was recently updated to use serdev, so add the appropriate
dependency. Without this one can get compiler warnings like this if
CONFIG_SERIAL_DEV_BUS is not enabled:
CC [M] drivers/bluetooth/hci_h5.o
drivers/bluetooth/hci_h5.c:934:36: warning: ‘h5_serdev_driver’ defined but not used [-Wunused-variable]
static struct serdev_device_driver h5_serdev_driver = {
^~~~~~~~~~~~~~~~
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jae Hyun Yoo [Tue, 24 Jul 2018 20:36:15 +0000 (13:36 -0700)]
i2c: aspeed: Add an explicit type casting for *get_clk_reg_val
[ Upstream commit
5799c4b2f1dbc0166d9b1d94443deaafc6e7a070 ]
This commit fixes this sparse warning:
drivers/i2c/busses/i2c-aspeed.c:875:38: warning: incorrect type in assignment (different modifiers)
drivers/i2c/busses/i2c-aspeed.c:875:38: expected unsigned int ( *get_clk_reg_val )( ... )
drivers/i2c/busses/i2c-aspeed.c:875:38: got void const *const data
Reported-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Reviewed-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Florian Fainelli [Sat, 4 Aug 2018 21:20:40 +0000 (14:20 -0700)]
ethtool: Remove trailing semicolon for static inline
[ Upstream commit
d89d41556141a527030a15233135ba622ba3350d ]
Android's header sanitization tool chokes on static inline functions having a
trailing semicolon, leading to an incorrectly parsed header file. While the
tool should obviously be fixed, also fix the header files for the two affected
functions: ethtool_get_flow_spec_ring() and ethtool_get_flow_spec_ring_vf().
Fixes:
8cf6f497de40 ("ethtool: Add helper routines to pass vf to rx_flow_spec")
Reporetd-by: Blair Prescott <blair.prescott@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dan Carpenter [Thu, 2 Aug 2018 08:42:22 +0000 (11:42 +0300)]
misc: mic: SCIF Fix scif_get_new_port() error handling
[ Upstream commit
a39284ae9d2ad09975c8ae33f1bd0f05fbfbf6ee ]
There are only 2 callers of scif_get_new_port() and both appear to get
the error handling wrong. Both treat zero returns as error, but it
actually returns negative error codes and >= 0 on success.
Fixes:
e9089f43c9a7 ("misc: mic: SCIF open close bind and listen APIs")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alexey Brodkin [Thu, 2 Aug 2018 08:50:16 +0000 (11:50 +0300)]
ARC: [plat-axs*]: Enable SWAP
commit
c83532fb0fe053d2e43e9387354cb1b52ba26427 upstream.
SWAP support on ARC was fixed earlier by
commit
6e3761145a9b ("ARC: Fix CONFIG_SWAP")
so now we may safely enable it on platforms that
have external media like USB and SD-card.
Note: it was already allowed for HSDK
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: stable@vger.kernel.org # 6e3761145a9b: ARC: Fix CONFIG_SWAP
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tomas Winkler [Thu, 28 Jun 2018 15:13:33 +0000 (18:13 +0300)]
tpm: separate cmd_ready/go_idle from runtime_pm
commit
627448e85c766587f6fdde1ea3886d6615081c77 upstream.
Fix tpm ptt initialization error:
tpm tpm0: A TPM error (378) occurred get tpm pcr allocation.
We cannot use go_idle cmd_ready commands via runtime_pm handles
as with the introduction of localities this is no longer an optional
feature, while runtime pm can be not enabled.
Though cmd_ready/go_idle provides a power saving, it's also a part of
TPM2 protocol and should be called explicitly.
This patch exposes cmd_read/go_idle via tpm class ops and removes
runtime pm support as it is not used by any driver.
When calling from nested context always use both flags:
TPM_TRANSMIT_UNLOCKED and TPM_TRANSMIT_RAW. Both are needed to resolve
tpm spaces and locality request recursive calls to tpm_transmit().
TPM_TRANSMIT_RAW should never be used standalone as it will fail
on double locking. While TPM_TRANSMIT_UNLOCKED standalone should be
called from non-recursive locked contexts.
New wrappers are added tpm_cmd_ready() and tpm_go_idle() to
streamline tpm_try_transmit code.
tpm_crb no longer needs own power saving functions and can drop using
tpm_pm_suspend/resume.
This patch cannot be really separated from the locality fix.
Fixes:
888d867df441 (tpm: cmd_ready command can be issued only after granting locality)
Cc: stable@vger.kernel.org
Fixes:
888d867df441 (tpm: cmd_ready command can be issued only after granting locality)
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Arnd Bergmann [Mon, 15 Jan 2018 16:07:22 +0000 (17:07 +0100)]
crypto: aes-generic - fix aes-generic regression on powerpc
commit
6e36719fbe90213fbba9f50093fa2d4d69b0e93c upstream.
My last bugfix added -Os on the command line, which unfortunately caused
a build regression on powerpc in some configurations.
I've done some more analysis of the original problem and found slightly
different workaround that avoids this regression and also results in
better performance on gcc-7.0: -fcode-hoisting is an optimization step
that got added in gcc-7 and that for all gcc-7 versions causes worse
performance.
This disables -fcode-hoisting on all compilers that understand the option.
For gcc-7.1 and 7.2 I found the same performance as my previous patch
(using -Os), in gcc-7.0 it was even better. On gcc-8 I could see no
change in performance from this patch. In theory, code hoisting should
not be able make things better for the AES cipher, so leaving it
disabled for gcc-8 only serves to simplify the Makefile change.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Link: https://www.mail-archive.com/linux-crypto@vger.kernel.org/msg30418.html
Link: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=83356
Link: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=83651
Fixes:
148b974deea9 ("crypto: aes-generic - build with -Os on gcc-7+")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Horia Geanta <horia.geanta@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Gustavo A. R. Silva [Thu, 16 Aug 2018 19:06:46 +0000 (14:06 -0500)]
switchtec: Fix Spectre v1 vulnerability
commit
46feb6b495f7628a6dbf36c4e6d80faf378372d4 upstream.
p.port can is indirectly controlled by user-space, hence leading to
a potential exploitation of the Spectre variant 1 vulnerability.
This issue was detected with the help of Smatch:
drivers/pci/switch/switchtec.c:912 ioctl_port_to_pff() warn: potential spectre issue 'pcfg->dsp_pff_inst_id' [r]
Fix this by sanitizing p.port before using it to index
pcfg->dsp_pff_inst_id
Notice that given that speculation windows are large, the policy is to kill
the speculation on the first load and not worry if it can be completed with
a dependent load/store [1].
[1] https://marc.info/?l=linux-kernel&m=
152449131114778&w=2
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Logan Gunthorpe <logang@deltatee.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Filippo Sironi [Tue, 31 Jul 2018 15:29:30 +0000 (17:29 +0200)]
x86/microcode: Update the new microcode revision unconditionally
commit
8da38ebaad23fe1b0c4a205438676f6356607cfc upstream.
Handle the case where microcode gets loaded on the BSP's hyperthread
sibling first and the boot_cpu_data's microcode revision doesn't get
updated because of early exit due to the siblings sharing a microcode
engine.
For that, simply write the updated revision on all CPUs unconditionally.
Signed-off-by: Filippo Sironi <sironi@amazon.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: prarit@redhat.com
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/1533050970-14385-1-git-send-email-sironi@amazon.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Prarit Bhargava [Tue, 31 Jul 2018 11:27:39 +0000 (07:27 -0400)]
x86/microcode: Make sure boot_cpu_data.microcode is up-to-date
commit
370a132bb2227ff76278f98370e0e701d86ff752 upstream.
When preparing an MCE record for logging, boot_cpu_data.microcode is used
to read out the microcode revision on the box.
However, on systems where late microcode update has happened, the microcode
revision output in a MCE log record is wrong because
boot_cpu_data.microcode is not updated when the microcode gets updated.
But, the microcode revision saved in boot_cpu_data's microcode member
should be kept up-to-date, regardless, for consistency.
Make it so.
Fixes:
fa94d0c6e0f3 ("x86/MCE: Save microcode revision in machine check records")
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: sironi@amazon.de
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/20180731112739.32338-1-prarit@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Thomas Gleixner [Thu, 6 Sep 2018 13:21:38 +0000 (15:21 +0200)]
cpu/hotplug: Prevent state corruption on error rollback
commit
69fa6eb7d6a64801ea261025cce9723d9442d773 upstream.
When a teardown callback fails, the CPU hotplug code brings the CPU back to
the previous state. The previous state becomes the new target state. The
rollback happens in undo_cpu_down() which increments the state
unconditionally even if the state is already the same as the target.
As a consequence the next CPU hotplug operation will start at the wrong
state. This is easily to observe when __cpu_disable() fails.
Prevent the unconditional undo by checking the state vs. target before
incrementing state and fix up the consequently wrong conditional in the
unplug code which handles the failure of the final CPU take down on the
control CPU side.
Fixes:
4dddfb5faa61 ("smp/hotplug: Rewrite AP state machine core")
Reported-by: Neeraj Upadhyay <neeraju@codeaurora.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Sudeep Holla <sudeep.holla@arm.com>
Tested-by: Neeraj Upadhyay <neeraju@codeaurora.org>
Cc: josh@joshtriplett.org
Cc: peterz@infradead.org
Cc: jiangshanlai@gmail.com
Cc: dzickus@redhat.com
Cc: brendan.jackman@arm.com
Cc: malat@debian.org
Cc: sramana@codeaurora.org
Cc: linux-arm-msm@vger.kernel.org
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/alpine.DEB.2.21.1809051419580.1416@nanos.tec.linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
----
Neeraj Upadhyay [Wed, 5 Sep 2018 05:52:07 +0000 (11:22 +0530)]
cpu/hotplug: Adjust misplaced smb() in cpuhp_thread_fun()
commit
f8b7530aa0a1def79c93101216b5b17cf408a70a upstream.
The smp_mb() in cpuhp_thread_fun() is misplaced. It needs to be after the
load of st->should_run to prevent reordering of the later load/stores
w.r.t. the load of st->should_run.
Fixes:
4dddfb5faa61 ("smp/hotplug: Rewrite AP state machine core")
Signed-off-by: Neeraj Upadhyay <neeraju@codeaurora.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infraded.org>
Cc: josh@joshtriplett.org
Cc: peterz@infradead.org
Cc: jiangshanlai@gmail.com
Cc: dzickus@redhat.com
Cc: brendan.jackman@arm.com
Cc: malat@debian.org
Cc: mojha@codeaurora.org
Cc: sramana@codeaurora.org
Cc: linux-arm-msm@vger.kernel.org
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/1536126727-11629-1-git-send-email-neeraju@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Takashi Iwai [Thu, 30 Aug 2018 13:13:16 +0000 (15:13 +0200)]
ALSA: hda - Fix cancel_work_sync() stall from jackpoll work
commit
16037643969e095509cd8446a3f8e406a6dc3a2c upstream.
On AMD/ATI controllers, the HD-audio controller driver allows a bus
reset upon the error recovery, and its procedure includes the
cancellation of pending jack polling work as found in
snd_hda_bus_codec_reset(). This works usually fine, but it becomes a
problem when the reset happens from the jack poll work itself; then
calling cancel_work_sync() from the work being processed tries to wait
the finish endlessly.
As a workaround, this patch adds the check of current_work() and
applies the cancel_work_sync() only when it's not from the
jackpoll_work.
This doesn't fix the root cause of the reported error below, but at
least, it eases the unexpected stall of the whole system.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=200937
Cc: <stable@vger.kernel.org>
Cc: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sean Christopherson [Thu, 23 Aug 2018 20:56:46 +0000 (13:56 -0700)]
KVM: VMX: Do not allow reexecute_instruction() when skipping MMIO instr
commit
c4409905cd6eb42cfd06126e9226b0150e05a715 upstream.
Re-execution after an emulation decode failure is only intended to
handle a case where two or vCPUs race to write a shadowed page, i.e.
we should never re-execute an instruction as part of MMIO emulation.
As handle_ept_misconfig() is only used for MMIO emulation, it should
pass EMULTYPE_NO_REEXECUTE when using the emulator to skip an instr
in the fast-MMIO case where VM_EXIT_INSTRUCTION_LEN is invalid.
And because the cr2 value passed to x86_emulate_instruction() is only
destined for use when retrying or reexecuting, we can simply call
emulate_instruction().
Fixes:
d391f1207067 ("x86/kvm/vmx: do not use vm-exit instruction length
for fast MMIO when running nested")
Cc: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pierre Morel [Thu, 23 Aug 2018 10:25:54 +0000 (12:25 +0200)]
KVM: s390: vsie: copy wrapping keys to right place
commit
204c97245612b6c255edf4e21e24d417c4a0c008 upstream.
Copy the key mask to the right offset inside the shadow CRYCB
Fixes:
bbeaa58b3 ("KVM: s390: vsie: support aes dea wrapping keys")
Signed-off-by: Pierre Morel <pmorel@linux.ibm.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Janosch Frank <frankja@linux.ibm.com>
Cc: stable@vger.kernel.org # v4.8+
Message-Id: <
1535019956-23539-2-git-send-email-pmorel@linux.ibm.com>
Signed-off-by: Janosch Frank <frankja@linux.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Filipe Manana [Fri, 17 Aug 2018 08:38:59 +0000 (09:38 +0100)]
Btrfs: fix data corruption when deduplicating between different files
commit
de02b9f6bb65a6a1848f346f7a3617b7a9b930c0 upstream.
If we deduplicate extents between two different files we can end up
corrupting data if the source range ends at the size of the source file,
the source file's size is not aligned to the filesystem's block size
and the destination range does not go past the size of the destination
file size.
Example:
$ mkfs.btrfs -f /dev/sdb
$ mount /dev/sdb /mnt
$ xfs_io -f -c "pwrite -S 0x6b 0 2518890" /mnt/foo
# The first byte with a value of 0xae starts at an offset (2518890)
# which is not a multiple of the sector size.
$ xfs_io -c "pwrite -S 0xae 2518890 102398" /mnt/foo
# Confirm the file content is full of bytes with values 0x6b and 0xae.
$ od -t x1 /mnt/foo
0000000 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b
*
11467540 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b ae ae ae ae ae ae
11467560 ae ae ae ae ae ae ae ae ae ae ae ae ae ae ae ae
*
11777540 ae ae ae ae ae ae ae ae
11777550
# Create a second file with a length not aligned to the sector size,
# whose bytes all have the value 0x6b, so that its extent(s) can be
# deduplicated with the first file.
$ xfs_io -f -c "pwrite -S 0x6b 0 557771" /mnt/bar
# Now deduplicate the entire second file into a range of the first file
# that also has all bytes with the value 0x6b. The destination range's
# end offset must not be aligned to the sector size and must be less
# then the offset of the first byte with the value 0xae (byte at offset
# 2518890).
$ xfs_io -c "dedupe /mnt/bar 0 1957888 557771" /mnt/foo
# The bytes in the range starting at offset 2515659 (end of the
# deduplication range) and ending at offset 2519040 (start offset
# rounded up to the block size) must all have the value 0xae (and not
# replaced with 0x00 values). In other words, we should have exactly
# the same data we had before we asked for deduplication.
$ od -t x1 /mnt/foo
0000000 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b
*
11467540 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b ae ae ae ae ae ae
11467560 ae ae ae ae ae ae ae ae ae ae ae ae ae ae ae ae
*
11777540 ae ae ae ae ae ae ae ae
11777550
# Unmount the filesystem and mount it again. This guarantees any file
# data in the page cache is dropped.
$ umount /dev/sdb
$ mount /dev/sdb /mnt
$ od -t x1 /mnt/foo
0000000 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b
*
11461300 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 00 00 00 00 00
11461320 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
*
11470000 ae ae ae ae ae ae ae ae ae ae ae ae ae ae ae ae
*
11777540 ae ae ae ae ae ae ae ae
11777550
# The bytes in range 2515659 to 2519040 have a value of 0x00 and not a
# value of 0xae, data corruption happened due to the deduplication
# operation.
So fix this by rounding down, to the sector size, the length used for the
deduplication when the following conditions are met:
1) Source file's range ends at its i_size;
2) Source file's i_size is not aligned to the sector size;
3) Destination range does not cross the i_size of the destination file.
Fixes:
e1d227a42ea2 ("btrfs: Handle unaligned length in extent_same")
CC: stable@vger.kernel.org # 4.2+
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Steve French [Fri, 31 Aug 2018 20:12:10 +0000 (15:12 -0500)]
smb3: check for and properly advertise directory lease support
commit
f801568332321e2b1e7a8bd26c3e4913a312a2ec upstream.
Although servers will typically ignore unsupported features,
we should advertise the support for directory leases (as
Windows e.g. does) in the negotiate protocol capabilities we
pass to the server, and should check for the server capability
(CAP_DIRECTORY_LEASING) before sending a lease request for an
open of a directory. This will prevent us from accidentally
sending directory leases to SMB2.1 or SMB2 server for example.
Signed-off-by: Steve French <stfrench@microsoft.com>
CC: Stable <stable@vger.kernel.org>
Reviewed-by: Ronnie Sahlberg <lsahlber@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Steve French [Mon, 27 Aug 2018 22:04:13 +0000 (17:04 -0500)]
SMB3: Backup intent flag missing for directory opens with backupuid mounts
commit
5e19697b56a64004e2d0ff1bb952ea05493c088f upstream.
When "backup intent" is requested on the mount (e.g. backupuid or
backupgid mount options), the corresponding flag needs to be set
on opens of directories (and files) but was missing in some
places causing access denied trying to enumerate and backup
servers.
Fixes kernel bugzilla #200953
https://bugzilla.kernel.org/show_bug.cgi?id=200953
Reported-and-tested-by: <whh@rubrik.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
CC: Stable <stable@vger.kernel.org>
Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Paul Burton [Thu, 30 Aug 2018 18:01:21 +0000 (11:01 -0700)]
MIPS: VDSO: Match data page cache colouring when D$ aliases
commit
0f02cfbc3d9e413d450d8d0fd660077c23f67eff upstream.
When a system suffers from dcache aliasing a user program may observe
stale VDSO data from an aliased cache line. Notably this can break the
expectation that clock_gettime(CLOCK_MONOTONIC, ...) is, as its name
suggests, monotonic.
In order to ensure that users observe updates to the VDSO data page as
intended, align the user mappings of the VDSO data page such that their
cache colouring matches that of the virtual address range which the
kernel will use to update the data page - typically its unmapped address
within kseg0.
This ensures that we don't introduce aliasing cache lines for the VDSO
data page, and therefore that userland will observe updates without
requiring cache invalidation.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Reported-by: Hauke Mehrtens <hauke@hauke-m.de>
Reported-by: Rene Nielsen <rene.nielsen@microsemi.com>
Reported-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Fixes:
ebb5e78cc634 ("MIPS: Initial implementation of a VDSO")
Patchwork: https://patchwork.linux-mips.org/patch/20344/
Tested-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Tested-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: James Hogan <jhogan@kernel.org>
Cc: linux-mips@linux-mips.org
Cc: stable@vger.kernel.org # v4.4+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Minchan Kim [Thu, 23 Aug 2018 05:29:56 +0000 (14:29 +0900)]
android: binder: fix the race mmap and alloc_new_buf_locked
commit
da1b9564e85b1d7baf66cbfabcab27e183a1db63 upstream.
There is RaceFuzzer report like below because we have no lock to close
below the race between binder_mmap and binder_alloc_new_buf_locked.
To close the race, let's use memory barrier so that if someone see
alloc->vma is not NULL, alloc->vma_vm_mm should be never NULL.
(I didn't add stable mark intentionallybecause standard android
userspace libraries that interact with binder (libbinder & libhwbinder)
prevent the mmap/ioctl race. - from Todd)
"
Thread interleaving:
CPU0 (binder_alloc_mmap_handler) CPU1 (binder_alloc_new_buf_locked)
===== =====
// drivers/android/binder_alloc.c
// #L718 (v4.18-rc3)
alloc->vma = vma;
// drivers/android/binder_alloc.c
// #L346 (v4.18-rc3)
if (alloc->vma == NULL) {
...
// alloc->vma is not NULL at this point
return ERR_PTR(-ESRCH);
}
...
// #L438
binder_update_page_range(alloc, 0,
(void *)PAGE_ALIGN((uintptr_t)buffer->data),
end_page_addr);
// In binder_update_page_range() #L218
// But still alloc->vma_vm_mm is NULL here
if (need_mm && mmget_not_zero(alloc->vma_vm_mm))
alloc->vma_vm_mm = vma->vm_mm;
Crash Log:
==================================================================
BUG: KASAN: null-ptr-deref in __atomic_add_unless include/asm-generic/atomic-instrumented.h:89 [inline]
BUG: KASAN: null-ptr-deref in atomic_add_unless include/linux/atomic.h:533 [inline]
BUG: KASAN: null-ptr-deref in mmget_not_zero include/linux/sched/mm.h:75 [inline]
BUG: KASAN: null-ptr-deref in binder_update_page_range+0xece/0x18e0 drivers/android/binder_alloc.c:218
Write of size 4 at addr
0000000000000058 by task syz-executor0/11184
CPU: 1 PID: 11184 Comm: syz-executor0 Not tainted 4.18.0-rc3 #1
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.8.2-0-g33fbe13 by qemu-project.org 04/01/2014
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x16e/0x22c lib/dump_stack.c:113
kasan_report_error mm/kasan/report.c:352 [inline]
kasan_report+0x163/0x380 mm/kasan/report.c:412
check_memory_region_inline mm/kasan/kasan.c:260 [inline]
check_memory_region+0x140/0x1a0 mm/kasan/kasan.c:267
kasan_check_write+0x14/0x20 mm/kasan/kasan.c:278
__atomic_add_unless include/asm-generic/atomic-instrumented.h:89 [inline]
atomic_add_unless include/linux/atomic.h:533 [inline]
mmget_not_zero include/linux/sched/mm.h:75 [inline]
binder_update_page_range+0xece/0x18e0 drivers/android/binder_alloc.c:218
binder_alloc_new_buf_locked drivers/android/binder_alloc.c:443 [inline]
binder_alloc_new_buf+0x467/0xc30 drivers/android/binder_alloc.c:513
binder_transaction+0x125b/0x4fb0 drivers/android/binder.c:2957
binder_thread_write+0xc08/0x2770 drivers/android/binder.c:3528
binder_ioctl_write_read.isra.39+0x24f/0x8e0 drivers/android/binder.c:4456
binder_ioctl+0xa86/0xf34 drivers/android/binder.c:4596
vfs_ioctl fs/ioctl.c:46 [inline]
do_vfs_ioctl+0x154/0xd40 fs/ioctl.c:686
ksys_ioctl+0x94/0xb0 fs/ioctl.c:701
__do_sys_ioctl fs/ioctl.c:708 [inline]
__se_sys_ioctl fs/ioctl.c:706 [inline]
__x64_sys_ioctl+0x43/0x50 fs/ioctl.c:706
do_syscall_64+0x167/0x4b0 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x49/0xbe
"
Signed-off-by: Todd Kjos <tkjos@google.com>
Signed-off-by: Minchan Kim <minchan@kernel.org>
Reviewed-by: Martijn Coenen <maco@android.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Konstantin Khlebnikov [Thu, 6 Sep 2018 08:05:44 +0000 (11:05 +0300)]
block: bfq: swap puts in bfqg_and_blkg_put
commit
d5274b3cd6a814ccb2f56d81ee87cbbf51bd4cf7 upstream.
Fix trivial use-after-free. This could be last reference to bfqg.
Fixes:
8f9bebc33dd7 ("block, bfq: access and cache blkg data only when safe")
Acked-by: Paolo Valente <paolo.valente@linaro.org>
Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jens Axboe [Tue, 4 Sep 2018 17:52:34 +0000 (11:52 -0600)]
nbd: don't allow invalid blocksize settings
commit
bc811f05d77f47059c197a98b6ad242eb03999cb upstream.
syzbot reports a divide-by-zero off the NBD_SET_BLKSIZE ioctl.
We need proper validation of the input here. Not just if it's
zero, but also if the value is a power-of-2 and in a valid
range. Add that.
Cc: stable@vger.kernel.org
Reported-by: syzbot <syzbot+25dbecbec1e62c6b0dd4@syzkaller.appspotmail.com>
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
James Smart [Thu, 16 Aug 2018 23:04:05 +0000 (16:04 -0700)]
scsi: lpfc: Correct MDS diag and nvmet configuration
commit
53e13ee087a80e8d4fc95436318436e5c2c1f8c2 upstream.
A recent change added some MDS processing in the lpfc_drain_txq routine
that relies on the fcp_wq being allocated. For nvmet operation the fcp_wq
is not allocated because it can only be an nvme-target. When the original
MDS support was added LS_MDS_LOOPBACK was defined wrong, (0x16) it should
have been 0x10 (decimal value used for hex setting). This incorrect value
allowed MDS_LOOPBACK to be set simultaneously with LS_NPIV_FAB_SUPPORTED,
causing the driver to crash when it accesses the non-existent fcp_wq.
Correct the bad value setting for LS_MDS_LOOPBACK.
Fixes:
ae9e28f36a6c ("lpfc: Add MDS Diagnostic support.")
Cc: <stable@vger.kernel.org> # v4.12+
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Tested-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Felipe Balbi [Mon, 3 Sep 2018 08:24:57 +0000 (11:24 +0300)]
i2c: i801: fix DNV's SMBCTRL register offset
commit
851a15114895c5bce163a6f2d57e0aa4658a1be4 upstream.
DNV's iTCO is slightly different with SMBCTRL sitting at a different
offset when compared to all other devices. Let's fix so that we can
properly use iTCO watchdog.
Fixes:
84d7f2ebd70d ("i2c: i801: Add support for Intel DNV")
Cc: <stable@vger.kernel.org> # v4.4+
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Shubhrajyoti Datta [Mon, 3 Sep 2018 09:41:11 +0000 (15:11 +0530)]
i2c: xiic: Make the start and the byte count write atomic
commit
ae7304c3ea28a3ba47a7a8312c76c654ef24967e upstream.
Disable interrupts while configuring the transfer and enable them back.
We have below as the programming sequence
1. start and slave address
2. byte count and stop
In some customer platform there was a lot of interrupts between 1 and 2
and after slave address (around 7 clock cyles) if 2 is not executed
then the transaction is nacked.
To fix this case make the 2 writes atomic.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
[wsa: added a newline for better readability]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Greg Kroah-Hartman [Sat, 15 Sep 2018 07:45:37 +0000 (09:45 +0200)]
Linux 4.14.70
Suzuki K Poulose [Wed, 4 Jul 2018 22:07:46 +0000 (23:07 +0100)]
arm64: Handle mismatched cache type
commit
314d53d297980676011e6fd83dac60db4a01dc70 upstream.
Track mismatches in the cache type register (CTR_EL0), other
than the D/I min line sizes and trap user accesses if there are any.
Fixes:
be68a8aaf925 ("arm64: cpufeature: Fix CTR_EL0 field definitions")
Cc: <stable@vger.kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Suzuki K Poulose [Wed, 4 Jul 2018 22:07:45 +0000 (23:07 +0100)]
arm64: Fix mismatched cache line size detection
commit
4c4a39dd5fe2d13e2d2fa5fceb8ef95d19fc389a upstream.
If there is a mismatch in the I/D min line size, we must
always use the system wide safe value both in applications
and in the kernel, while performing cache operations. However,
we have been checking more bits than just the min line sizes,
which triggers false negatives. We may need to trap the user
accesses in such cases, but not necessarily patch the kernel.
This patch fixes the check to do the right thing as advertised.
A new capability will be added to check mismatches in other
fields and ensure we trap the CTR accesses.
Fixes:
be68a8aaf925 ("arm64: cpufeature: Fix CTR_EL0 field definitions")
Cc: <stable@vger.kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Reported-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Gustavo A. R. Silva [Mon, 6 Aug 2018 12:14:51 +0000 (07:14 -0500)]
ASoC: wm8994: Fix missing break in switch
commit
ad0eaee6195db1db1749dd46b9e6f4466793d178 upstream.
Add missing break statement in order to prevent the code from falling
through to the default case.
Addresses-Coverity-ID: 115050 ("Missing break in switch")
Reported-by: Valdis Kletnieks <valdis.kletnieks@vt.edu>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
[Gustavo: Backported to 3.16..4.18 - Remove code comment removal]
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Arnd Bergmann [Tue, 5 Jun 2018 11:50:07 +0000 (13:50 +0200)]
arm64: cpu_errata: include required headers
commit
94a5d8790e79ab78f499d2d9f1ff2cab63849d9f upstream.
Without including psci.h and arm-smccc.h, we now get a build failure in
some configurations:
arch/arm64/kernel/cpu_errata.c: In function 'arm64_update_smccc_conduit':
arch/arm64/kernel/cpu_errata.c:278:10: error: 'psci_ops' undeclared (first use in this function); did you mean 'sysfs_ops'?
arch/arm64/kernel/cpu_errata.c: In function 'arm64_set_ssbd_mitigation':
arch/arm64/kernel/cpu_errata.c:311:3: error: implicit declaration of function 'arm_smccc_1_1_hvc' [-Werror=implicit-function-declaration]
arm_smccc_1_1_hvc(ARM_SMCCC_ARCH_WORKAROUND_2, state, NULL);
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Arnd Bergmann [Mon, 20 Aug 2018 21:37:50 +0000 (23:37 +0200)]
x86: kvm: avoid unused variable warning
commit
7288bde1f9df6c1475675419bdd7725ce84dec56 upstream.
Removing one of the two accesses of the maxphyaddr variable led to
a harmless warning:
arch/x86/kvm/x86.c: In function 'kvm_set_mmio_spte_mask':
arch/x86/kvm/x86.c:6563:6: error: unused variable 'maxphyaddr' [-Werror=unused-variable]
Removing the #ifdef seems to be the nicest workaround, as it
makes the code look cleaner than adding another #ifdef.
Fixes:
28a1f3ac1d0c ("kvm: x86: Set highest physical address bits in non-present/reserved SPTEs")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: stable@vger.kernel.org # L1TF
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Junaid Shahid [Tue, 14 Aug 2018 17:15:34 +0000 (10:15 -0700)]
kvm: x86: Set highest physical address bits in non-present/reserved SPTEs
commit
28a1f3ac1d0c8558ee4453d9634dad891a6e922e upstream.
Always set the 5 upper-most supported physical address bits to 1 for SPTEs
that are marked as non-present or reserved, to make them unusable for
L1TF attacks from the guest. Currently, this just applies to MMIO SPTEs.
(We do not need to mark PTEs that are completely 0 as physical page 0
is already reserved.)
This allows mitigation of L1TF without disabling hyper-threading by using
shadow paging mode instead of EPT.
Signed-off-by: Junaid Shahid <junaids@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fabio Estevam [Mon, 3 Sep 2018 13:39:17 +0000 (10:39 -0300)]
Revert "ARM: imx_v6_v7_defconfig: Select ULPI support"
This reverts commit
2059e527a659cf16d6bb709f1c8509f7a7623fc4.
This commit causes reboot to fail on imx6 wandboard, so let's
revert it.
Cc: <stable@vger.kernel.org> #4.14
Reported-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tyler Hicks [Tue, 4 Sep 2018 15:24:05 +0000 (15:24 +0000)]
irda: Only insert new objects into the global database via setsockopt
The irda_setsockopt() function conditionally allocates memory for a new
self->ias_object or, in some cases, reuses the existing
self->ias_object. Existing objects were incorrectly reinserted into the
LM_IAS database which corrupted the doubly linked list used for the
hashbin implementation of the LM_IAS database. When combined with a
memory leak in irda_bind(), this issue could be leveraged to create a
use-after-free vulnerability in the hashbin list. This patch fixes the
issue by only inserting newly allocated objects into the database.
CVE-2018-6555
Fixes:
1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Tyler Hicks <tyhicks@canonical.com>
Reviewed-by: Seth Arnold <seth.arnold@canonical.com>
Reviewed-by: Stefan Bader <stefan.bader@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tyler Hicks [Tue, 4 Sep 2018 15:24:04 +0000 (15:24 +0000)]
irda: Fix memory leak caused by repeated binds of irda socket
The irda_bind() function allocates memory for self->ias_obj without
checking to see if the socket is already bound. A userspace process
could repeatedly bind the socket, have each new object added into the
LM-IAS database, and lose the reference to the old object assigned to
the socket to exhaust memory resources. This patch errors out of the
bind operation when self->ias_obj is already assigned.
CVE-2018-6554
Fixes:
1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Tyler Hicks <tyhicks@canonical.com>
Reviewed-by: Seth Arnold <seth.arnold@canonical.com>
Reviewed-by: Stefan Bader <stefan.bader@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Martin Schwidefsky [Mon, 6 Aug 2018 11:49:47 +0000 (13:49 +0200)]
s390/lib: use expoline for all bcr instructions
commit
5eda25b10297684c1f46a14199ec00210f3c346e upstream.
The memove, memset, memcpy, __memset16, __memset32 and __memset64
function have an additional indirect return branch in form of a
"bzr" instruction. These need to use expolines as well.
Cc: <stable@vger.kernel.org> # v4.17+
Fixes:
97489e0663 ("s390/lib: use expoline for indirect branches")
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Randy Dunlap [Tue, 28 Aug 2018 19:59:10 +0000 (12:59 -0700)]
kbuild: make missing $DEPMOD a Warning instead of an Error
commit
914b087ff9e0e9a399a4927fa30793064afc0178 upstream.
When $DEPMOD is not found, only print a warning instead of exiting
with an error message and error status:
Warning: 'make modules_install' requires /sbin/depmod. Please install it.
This is probably in the kmod package.
Change the Error to a Warning because "not all build hosts for cross
compiling Linux are Linux systems and are able to provide a working
port of depmod, especially at the file patch /sbin/depmod."
I.e., "make modules_install" may be used to copy/install the
loadable modules files to a target directory on a build system and
then transferred to an embedded device where /sbin/depmod is run
instead of it being run on the build system.
Fixes:
934193a654c1 ("kbuild: verify that $DEPMOD is installed")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: H. Nikolaus Schaller <hns@goldelico.com>
Cc: stable@vger.kernel.org
Cc: Lucas De Marchi <lucas.demarchi@profusion.mobi>
Cc: Lucas De Marchi <lucas.de.marchi@gmail.com>
Cc: Michal Marek <michal.lkml@markovi.net>
Cc: Jessica Yu <jeyu@kernel.org>
Cc: Chih-Wei Huang <cwhuang@linux.org.tw>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Maxim Zhukov <mussitantesmortem@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fredrik Schön [Fri, 17 Aug 2018 20:07:28 +0000 (22:07 +0200)]
drm/i915: Increase LSPCON timeout
commit
299c2a904b1e8d5096d4813df6371357d97a6cd1 upstream.
100 ms is not enough time for the LSPCON adapter on Intel NUC devices to
settle. This causes dropped display modes at boot or screen reconfiguration.
Empirical testing can reproduce the error up to a timeout of 190 ms. Basic
boot and stress testing at 200 ms has not (yet) failed.
Increase timeout to 400 ms to get some margin of error.
Changes from v1:
The initial suggestion of 1000 ms was lowered due to concerns about delaying
valid timeout cases.
Update patch metadata.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=107503
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1570392
Fixes:
357c0ae9198a ("drm/i915/lspcon: Wait for expected LSPCON mode to settle")
Cc: Shashank Sharma <shashank.sharma@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: <stable@vger.kernel.org> # v4.11+
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Shashank Sharma <shashank.sharma@intel.com>
Signed-off-by: Fredrik Schön <fredrik.schon@gmail.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180817200728.8154-1-fredrik.schon@gmail.com
(cherry picked from commit
59f1c8ab30d6f9042562949f42cbd3f3cf69de94)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Shashank Sharma <shashank.sharma@intel.com>
Signed-off-by: Fredrik Schön <fredrik.schon@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Juergen Gross [Tue, 21 Aug 2018 15:37:54 +0000 (17:37 +0200)]
x86/xen: don't write ptes directly in 32-bit PV guests
commit
f7c90c2aa4004808dff777ba6ae2c7294dd06851 upstream.
In some cases 32-bit PAE PV guests still write PTEs directly instead of
using hypercalls. This is especially bad when clearing a PTE as this is
done via 32-bit writes which will produce intermediate L1TF attackable
PTEs.
Change the code to use hypercalls instead.
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Juergen Gross [Tue, 21 Aug 2018 15:37:55 +0000 (17:37 +0200)]
x86/pae: use 64 bit atomic xchg function in native_ptep_get_and_clear
commit
b2d7a075a1ccef2fb321d595802190c8e9b39004 upstream.
Using only 32-bit writes for the pte will result in an intermediate
L1TF vulnerable PTE. When running as a Xen PV guest this will at once
switch the guest to shadow mode resulting in a loss of performance.
Use arch_atomic64_xchg() instead which will perform the requested
operation atomically with all 64 bits.
Some performance considerations according to:
https://software.intel.com/sites/default/files/managed/ad/dc/Intel-Xeon-Scalable-Processor-throughput-latency.pdf
The main number should be the latency, as there is no tight loop around
native_ptep_get_and_clear().
"lock cmpxchg8b" has a latency of 20 cycles, while "lock xchg" (with a
memory operand) isn't mentioned in that document. "lock xadd" (with xadd
having 3 cycles less latency than xchg) has a latency of 11, so we can
assume a latency of 14 for "lock xchg".
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Jan Beulich <jbeulich@suse.com>
Tested-by: Jason Andryuk <jandryuk@gmail.com>
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
[ Atomic operations gained an arch_ prefix in
8bf705d13039
("locking/atomic/x86: Switch atomic.h to use atomic-instrumented.h") so
s/arch_atomic64_xchg/atomic64_xchg/ for backport.]
Signed-off-by: Jason Andryuk <jandryuk@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Roger Quadros [Mon, 12 Feb 2018 13:30:08 +0000 (15:30 +0200)]
usb: dwc3: core: Fix ULPI PHYs and prevent phy_get/ulpi_init during suspend/resume
commit
98112041bcca164676367e261c8c1073ef70cb51 upstream.
In order for ULPI PHYs to work, dwc3_phy_setup() and dwc3_ulpi_init()
must be doene before dwc3_core_get_phy().
commit
541768b08a40 ("usb: dwc3: core: Call dwc3_core_get_phy() before initializing phys")
broke this.
The other issue is that dwc3_core_get_phy() and dwc3_ulpi_init() should
be called only once during the life cycle of the driver. However,
as dwc3_core_init() is called during system suspend/resume it will
result in multiple calls to dwc3_core_get_phy() and dwc3_ulpi_init()
which is wrong.
Fix this by moving dwc3_ulpi_init() out of dwc3_phy_setup()
into dwc3_core_ulpi_init(). Use a flag 'ulpi_ready' to ensure that
dwc3_core_ulpi_init() is called only once from dwc3_core_init().
Use another flag 'phys_ready' to call dwc3_core_get_phy() only once from
dwc3_core_init().
Fixes:
541768b08a40 ("usb: dwc3: core: Call dwc3_core_get_phy() before initializing phys")
Fixes:
f54edb539c11 ("usb: dwc3: core: initialize ULPI before trying to get the PHY")
Cc: linux-stable <stable@vger.kernel.org> # >= v4.13
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dave Young [Fri, 1 Dec 2017 12:19:34 +0000 (20:19 +0800)]
HID: add quirk for another PIXART OEM mouse used by HP
commit
01cffe9ded15c0d664e0beb33c594e00c0d57bba upstream.
This mouse keep disconnecting in runleve 3 like below, add it needs the
quirk to mute the anoying messages.
[ 111.230555] usb 2-2: USB disconnect, device number 6
[ 112.718156] usb 2-2: new low-speed USB device number 7 using xhci_hcd
[ 112.941594] usb 2-2: New USB device found, idVendor=03f0, idProduct=094a
[ 112.984866] usb 2-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 113.027731] usb 2-2: Product: HP USB Optical Mouse
[ 113.069977] usb 2-2: Manufacturer: PixArt
[ 113.113500] input: PixArt HP USB Optical Mouse as /devices/pci0000:00/0000:00:14.0/usb2/2-2/2-2:1.0/0003:03F0:094A.0002/input/input14
[ 113.156787] hid-generic 0003:03F0:094A.0002: input: USB HID v1.11 Mouse [PixArt HP USB Optical Mouse] on usb-0000:00:14.0-2/input0
[ 173.262642] usb 2-2: USB disconnect, device number 7
[ 174.750244] usb 2-2: new low-speed USB device number 8 using xhci_hcd
[ 174.935740] usb 2-2: New USB device found, idVendor=03f0, idProduct=094a
[ 174.990435] usb 2-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 175.014984] usb 2-2: Product: HP USB Optical Mouse
[ 175.037886] usb 2-2: Manufacturer: PixArt
[ 175.061794] input: PixArt HP USB Optical Mouse as /devices/pci0000:00/0000:00:14.0/usb2/2-2/2-2:1.0/0003:03F0:094A.0003/input/input15
[ 175.084946] hid-generic 0003:03F0:094A.0003: input: USB HID v1.11 Mouse [PixArt HP USB Optical Mouse] on usb-0000:00:14.0-2/input0
Signed-off-by: Dave Young <dyoung@redhat.com>
Cc: stable@vger.kernel.org
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jan H. Schönherr [Sat, 20 Jan 2018 00:26:33 +0000 (16:26 -0800)]
mm: Fix devm_memremap_pages() collision handling
commit
77dd66a3c67c93ab401ccc15efff25578be281fd upstream.
If devm_memremap_pages() detects a collision while adding entries
to the radix-tree, we call pgmap_radix_release(). Unfortunately,
the function removes *all* entries for the range -- including the
entries that caused the collision in the first place.
Modify pgmap_radix_release() to take an additional argument to
indicate where to stop, so that only newly added entries are removed
from the tree.
Cc: <stable@vger.kernel.org>
Fixes:
9476df7d80df ("mm: introduce find_dev_pagemap()")
Signed-off-by: Jan H. Schönherr <jschoenh@amazon.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Javier González [Fri, 13 Oct 2017 12:46:03 +0000 (14:46 +0200)]
lightnvm: pblk: free padded entries in write buffer
commit
cd8ddbf7a5e206fe6995ab0aee245d597dd6a7f2 upstream.
When a REQ_FLUSH reaches pblk, the bio cannot be directly completed.
Instead, data on the write buffer is flushed and the bio is completed on
the completion pah. This might require some sectors to be padded in
order to guarantee a successful write.
This patch fixes a memory leak on the padded pages. A consequence of
this bad free was that internal bios not containing data (only a flush)
were not being completed.
Fixes:
a4bd217b4326 ("lightnvm: physical block device (pblk) target")
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Luca Abeni [Thu, 7 Sep 2017 10:09:29 +0000 (12:09 +0200)]
sched/deadline: Fix switching to -deadline
commit
295d6d5e373607729bcc8182c25afe964655714f upstream.
Fix a bug introduced in:
72f9f3fdc928 ("sched/deadline: Remove dl_new from struct sched_dl_entity")
After that commit, when switching to -deadline if the scheduling
deadline of a task is in the past then switched_to_dl() calls
setup_new_entity() to properly initialize the scheduling deadline
and runtime.
The problem is that the task is enqueued _before_ having its parameters
initialized by setup_new_entity(), and this can cause problems.
For example, a task with its out-of-date deadline in the past will
potentially be enqueued as the highest priority one; however, its
adjusted deadline may not be the earliest one.
This patch fixes the problem by initializing the task's parameters before
enqueuing it.
Signed-off-by: luca abeni <luca.abeni@santannapisa.it>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Daniel Bristot de Oliveira <bristot@redhat.com>
Cc: Juri Lelli <juri.lelli@arm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1504778971-13573-3-git-send-email-luca.abeni@santannapisa.it
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Joel Fernandes (Google) [Mon, 23 Jul 2018 21:25:31 +0000 (14:25 -0700)]
debugobjects: Make stack check warning more informative
commit
fc91a3c4c27acdca0bc13af6fbb68c35cfd519f2 upstream.
While debugging an issue debugobject tracking warned about an annotation
issue of an object on stack. It turned out that the issue was due to the
object in concern being on a different stack which was due to another
issue.
Thomas suggested to print the pointers and the location of the stack for
the currently running task. This helped to figure out that the object was
on the wrong stack.
As this is general useful information for debugging similar issues, make
the error message more informative by printing the pointers.
[ tglx: Massaged changelog ]
Signed-off-by: Joel Fernandes (Google) <joel@joelfernandes.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Waiman Long <longman@redhat.com>
Acked-by: Yang Shi <yang.shi@linux.alibaba.com>
Cc: kernel-team@android.com
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: astrachan@google.com
Link: https://lkml.kernel.org/r/20180723212531.202328-1-joel@joelfernandes.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Randy Dunlap [Tue, 4 Sep 2018 22:46:13 +0000 (15:46 -0700)]
uapi/linux/keyctl.h: don't use C++ reserved keyword as a struct member name
commit
8a2336e549d385bb0b46880435b411df8d8200e8 upstream.
Since this header is in "include/uapi/linux/", apparently people want to
use it in userspace programs -- even in C++ ones. However, the header
uses a C++ reserved keyword ("private"), so change that to "dh_private"
instead to allow the header file to be used in C++ userspace.
Fixes https://bugzilla.kernel.org/show_bug.cgi?id=191051
Link: http://lkml.kernel.org/r/0db6c314-1ef4-9bfa-1baa-7214dd2ee061@infradead.org
Fixes:
ddbb41148724 ("KEYS: Add KEYCTL_DH_COMPUTE command")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Cc: David Howells <dhowells@redhat.com>
Cc: James Morris <jmorris@namei.org>
Cc: "Serge E. Hallyn" <serge@hallyn.com>
Cc: Mat Martineau <mathew.j.martineau@linux.intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Likun Gao [Thu, 9 Aug 2018 16:31:42 +0000 (00:31 +0800)]
drm/amdgpu:add VCN booting with firmware loaded by PSP
commit
4d77c0f676e910fb1f1870738aa4bd168f253621 upstream.
Setup psp firmware loading for VCN, and make VCN block
booting from tmr mac address.
Signed-off-by: James Zhu <James.Zhu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Likun Gao <Likun.Gao@amd.com>
Signed-off-by: Likun Gao <Likun.Gao@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Likun Gao [Thu, 9 Aug 2018 16:31:41 +0000 (00:31 +0800)]
drm/amdgpu:add VCN support in PSP driver
commit
235ac9de625a0a586093ad81b3de6f7d7ab913ed upstream.
Add VCN support in PSP driver
Signed-off-by: James Zhu <James.Zhu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Likun Gao <Likun.Gao@amd.com>
Signed-off-by: Likun Gao <Likun.Gao@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Likun Gao [Thu, 9 Aug 2018 16:31:40 +0000 (00:31 +0800)]
drm/amdgpu:add new firmware id for VCN
commit
c9ca989696ff28ffb015cc2b7c5577938ef2626c upstream.
Add the new firmware id for VCN into the enum
Signed-off-by: James Zhu <James.Zhu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Likun Gao <Likun.Gao@amd.com>
Signed-off-by: Likun Gao <Likun.Gao@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
James Zhu [Thu, 9 Aug 2018 16:31:38 +0000 (00:31 +0800)]
drm/amdgpu:add tmr mc address into amdgpu_firmware_info
commit
abf412b3efb2f943d9b98a489e9aca836be21333 upstream.
amdgpu IP blocks booting need Trust Memory Region(tmr) mc address
of its firmware which is loaded by PSP
Signed-off-by: James Zhu <James.Zhu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Likun Gao <likun.gao@amd.com>
Signed-off-by: Likun Gao <Likun.Gao@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
James Zhu [Thu, 9 Aug 2018 16:31:39 +0000 (00:31 +0800)]
drm/amdgpu: update tmr mc address
commit
435198f33b56d7b875a8173a0227ddf0de285aa1 upstream.
Update tmr mc address with firmware loading address
which is returned from PSP firmware
Signed-off-by: James Zhu <James.Zhu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Likun Gao <Likun.Gao@amd.com>
Signed-off-by: Likun Gao <Likun.Gao@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Kai-Heng Feng [Thu, 23 Aug 2018 05:53:32 +0000 (05:53 +0000)]
drm/edid: Add 6 bpc quirk for SDC panel in Lenovo B50-80
commit
25da75043f8690fd083878447c91f289dfb63b87 upstream.
Another panel that reports "DFP 1.x compliant TMDS" but it supports 6bpc
instead of 8 bpc.
Apply 6 bpc quirk for the panel to fix it.
BugLink: https://bugs.launchpad.net/bugs/1788308
Cc: <stable@vger.kernel.org> # v4.8+
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20180823055332.7723-1-kai.heng.feng@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rex Zhu [Fri, 20 Jul 2018 08:26:46 +0000 (16:26 +0800)]
drm/amd/pp/Polaris12: Fix a chunk of registers missed to program
commit
2d227ec2c11c568910299e8f913bac2dda47397c upstream.
DIDTConfig_Polaris12[] table missed a big chunk of data.
Pointed by aidan.fabius <aidan.fabius@coreavi.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Rex Zhu <Rex.Zhu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Michel Dänzer [Thu, 19 Jul 2018 16:33:39 +0000 (18:33 +0200)]
drm/amdgpu: Fix RLC safe mode test in gfx_v9_0_enter_rlc_safe_mode
commit
226127a67e31a9518d9516d3e4890759b379d874 upstream.
We were testing the register offset, instead of the value stored in the
register, therefore always timing out the loop.
This reduces suspend time of the system in the bug report below by ~600
ms.
Cc: stable@vger.kernel.org
Bugzilla: https://bugs.freedesktop.org/107277
Tested-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Junwei Zhang <Jerry.Zhang@amd.com>
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Chris Wilson [Thu, 2 Aug 2018 14:04:16 +0000 (15:04 +0100)]
drm/i915/lpe: Mark LPE audio runtime pm as "no callbacks"
commit
75eef0f1ed478284911b8723a5bdb659499a7aac upstream.
The LPE audio is a child device of i915, it is powered up and down
alongside the igfx and presents no independent runtime interface. This
aptly fulfils the description of a "No-Callback" Device, so mark it
thus.
Fixes:
183c00350ccd ("drm/i915: Fix runtime PM for LPE audio")
Testcase: igt/pm_rpm/basic-pci-d3-state
Testcase: igt/pm_rpm/basic-rte
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: stable@vger.kernel.org
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180802140416.6062-1-chris@chris-wilson.co.uk
(cherry picked from commit
46e831abe864a6b59fa3de253a681c0f2ee1bf2f)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Marc Zyngier [Fri, 24 Aug 2018 15:06:34 +0000 (16:06 +0100)]
ARM: rockchip: Force CONFIG_PM on Rockchip systems
[ Upstream commit
d1558dfd9f22c99a5b8e1354ad881ee40749da89 ]
A number of the Rockchip-specific drivers (IOMMU, display controllers)
are now assuming that CONFIG_PM is set, and may completely misbehave
if that's not the case.
Since there is hardly any reason for this configuration option not
to be selected anyway, let's require it (in the same way Tegra already
does).
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Marc Zyngier [Fri, 24 Aug 2018 15:06:35 +0000 (16:06 +0100)]
arm64: rockchip: Force CONFIG_PM on Rockchip systems
[ Upstream commit
7db7a8f5638a2ffe0c0c0d55b5186b6191fd6af7 ]
A number of the Rockchip-specific drivers (IOMMU, display controllers)
are now assuming that CONFIG_PM is set, and may completely misbehave
if that's not the case.
Since there is hardly any reason for this configuration option not
to be selected anyway, let's require it (in the same way Tegra already
does).
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Qu Wenruo [Fri, 22 Jun 2018 04:35:00 +0000 (12:35 +0800)]
btrfs: Don't remove block group that still has pinned down bytes
[ Upstream commit
43794446548730ac8461be30bbe47d5d027d1d16 ]
[BUG]
Under certain KVM load and LTP tests, it is possible to hit the
following calltrace if quota is enabled:
BTRFS critical (device vda2): unable to find logical
8820195328 length 4096
BTRFS critical (device vda2): unable to find logical
8820195328 length 4096
WARNING: CPU: 0 PID: 49 at ../block/blk-core.c:172 blk_status_to_errno+0x1a/0x30
CPU: 0 PID: 49 Comm: kworker/u2:1 Not tainted 4.12.14-15-default #1 SLE15 (unreleased)
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.0.0-prebuilt.qemu-project.org 04/01/2014
Workqueue: btrfs-endio-write btrfs_endio_write_helper [btrfs]
task:
ffff9f827b340bc0 task.stack:
ffffb4f8c0304000
RIP: 0010:blk_status_to_errno+0x1a/0x30
Call Trace:
submit_extent_page+0x191/0x270 [btrfs]
? btrfs_create_repair_bio+0x130/0x130 [btrfs]
__do_readpage+0x2d2/0x810 [btrfs]
? btrfs_create_repair_bio+0x130/0x130 [btrfs]
? run_one_async_done+0xc0/0xc0 [btrfs]
__extent_read_full_page+0xe7/0x100 [btrfs]
? run_one_async_done+0xc0/0xc0 [btrfs]
read_extent_buffer_pages+0x1ab/0x2d0 [btrfs]
? run_one_async_done+0xc0/0xc0 [btrfs]
btree_read_extent_buffer_pages+0x94/0xf0 [btrfs]
read_tree_block+0x31/0x60 [btrfs]
read_block_for_search.isra.35+0xf0/0x2e0 [btrfs]
btrfs_search_slot+0x46b/0xa00 [btrfs]
? kmem_cache_alloc+0x1a8/0x510
? btrfs_get_token_32+0x5b/0x120 [btrfs]
find_parent_nodes+0x11d/0xeb0 [btrfs]
? leaf_space_used+0xb8/0xd0 [btrfs]
? btrfs_leaf_free_space+0x49/0x90 [btrfs]
? btrfs_find_all_roots_safe+0x93/0x100 [btrfs]
btrfs_find_all_roots_safe+0x93/0x100 [btrfs]
btrfs_find_all_roots+0x45/0x60 [btrfs]
btrfs_qgroup_trace_extent_post+0x20/0x40 [btrfs]
btrfs_add_delayed_data_ref+0x1a3/0x1d0 [btrfs]
btrfs_alloc_reserved_file_extent+0x38/0x40 [btrfs]
insert_reserved_file_extent.constprop.71+0x289/0x2e0 [btrfs]
btrfs_finish_ordered_io+0x2f4/0x7f0 [btrfs]
? pick_next_task_fair+0x2cd/0x530
? __switch_to+0x92/0x4b0
btrfs_worker_helper+0x81/0x300 [btrfs]
process_one_work+0x1da/0x3f0
worker_thread+0x2b/0x3f0
? process_one_work+0x3f0/0x3f0
kthread+0x11a/0x130
? kthread_create_on_node+0x40/0x40
ret_from_fork+0x35/0x40
BTRFS critical (device vda2): unable to find logical
8820195328 length 16384
BTRFS: error (device vda2) in btrfs_finish_ordered_io:3023: errno=-5 IO failure
BTRFS info (device vda2): forced readonly
BTRFS error (device vda2): pending csums is 2887680
[CAUSE]
It's caused by race with block group auto removal:
- There is a meta block group X, which has only one tree block
The tree block belongs to fs tree 257.
- In current transaction, some operation modified fs tree 257
The tree block gets COWed, so the block group X is empty, and marked
as unused, queued to be deleted.
- Some workload (like fsync) wakes up cleaner_kthread()
Which will call btrfs_delete_unused_bgs() to remove unused block
groups.
So block group X along its chunk map get removed.
- Some delalloc work finished for fs tree 257
Quota needs to get the original reference of the extent, which will
read tree blocks of commit root of 257.
Then since the chunk map gets removed, the above warning gets
triggered.
[FIX]
Just let btrfs_delete_unused_bgs() skip block group which still has
pinned bytes.
However there is a minor side effect: currently we only queue empty
blocks at update_block_group(), and such empty block group with pinned
bytes won't go through update_block_group() again, such block group
won't be removed, until it gets new extent allocated and removed.
Signed-off-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Qu Wenruo [Tue, 3 Jul 2018 09:10:07 +0000 (17:10 +0800)]
btrfs: relocation: Only remove reloc rb_trees if reloc control has been initialized
[ Upstream commit
389305b2aa68723c754f88d9dbd268a400e10664 ]
Invalid reloc tree can cause kernel NULL pointer dereference when btrfs
does some cleanup of the reloc roots.
It turns out that fs_info::reloc_ctl can be NULL in
btrfs_recover_relocation() as we allocate relocation control after all
reloc roots have been verified.
So when we hit: note, we haven't called set_reloc_control() thus
fs_info::reloc_ctl is still NULL.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=199833
Reported-by: Xu Wen <wen.xu@gatech.edu>
Signed-off-by: Qu Wenruo <wqu@suse.com>
Tested-by: Gu Jinxiang <gujx@cn.fujitsu.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Misono Tomohiro [Tue, 31 Jul 2018 07:20:21 +0000 (16:20 +0900)]
btrfs: replace: Reset on-disk dev stats value after replace
[ Upstream commit
1e7e1f9e3aba00c9b9c323bfeeddafe69ff21ff6 ]
on-disk devs stats value is updated in btrfs_run_dev_stats(),
which is called during commit transaction, if device->dev_stats_ccnt
is not zero.
Since current replace operation does not touch dev_stats_ccnt,
on-disk dev stats value is not updated. Therefore "btrfs device stats"
may return old device's value after umount/mount
(Example: See "btrfs ins dump-t -t DEV $DEV" after btrfs/100 finish).
Fix this by just incrementing dev_stats_ccnt in
btrfs_dev_replace_finishing() when replace is succeeded and this will
update the values.
Signed-off-by: Misono Tomohiro <misono.tomohiro@jp.fujitsu.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Qu Wenruo [Wed, 1 Aug 2018 02:37:20 +0000 (10:37 +0800)]
btrfs: Exit gracefully when chunk map cannot be inserted to the tree
[ Upstream commit
64f64f43c89aca1782aa672e0586f6903c5d8979 ]
It's entirely possible that a crafted btrfs image contains overlapping
chunks.
Although we can't detect such problem by tree-checker, it's not a
catastrophic problem, current extent map can already detect such problem
and return -EEXIST.
We just only need to exit gracefully and fail the mount.
Reported-by: Xu Wen <wen.xu@gatech.edu>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=200409
Signed-off-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jim Mattson [Fri, 27 Jul 2018 16:18:50 +0000 (09:18 -0700)]
kvm: nVMX: Fix fault vector for VMX operation at CPL > 0
[ Upstream commit
36090bf43a6b835a42f515cb515ff6fa293a25fe ]
The fault that should be raised for a privilege level violation is #GP
rather than #UD.
Fixes:
727ba748e110b4 ("kvm: nVMX: Enforce cpl=0 for VMX instructions")
Signed-off-by: Jim Mattson <jmattson@google.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sean Christopherson [Mon, 23 Jul 2018 19:32:42 +0000 (12:32 -0700)]
KVM: vmx: track host_state.loaded using a loaded_vmcs pointer
[ Upstream commit
bd9966de4e14fb559e89a06f7f5c9aab2cc028b9 ]
Using 'struct loaded_vmcs*' to track whether the CPU registers
contain host or guest state kills two birds with one stone.
1. The (effective) boolean host_state.loaded is poorly named.
It does not track whether or not host state is loaded into
the CPU registers (which most readers would expect), but
rather tracks if host state has been saved AND guest state
is loaded.
2. Using a loaded_vmcs pointer provides a more robust framework
for the optimized guest/host state switching, especially when
consideration per-VMCS enhancements. To that end, WARN_ONCE
if we try to switch to host state with a different VMCS than
was last used to save host state.
Resolve an occurrence of the new WARN by setting loaded_vmcs after
the call to vmx_vcpu_put() in vmx_switch_vmcs().
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Levin Du [Sat, 4 Aug 2018 07:31:02 +0000 (15:31 +0800)]
clk: rockchip: Add pclk_rkpwm_pmu to PMU critical clocks in rk3399
[ Upstream commit
640332d1a089909df08bc9f3e42888a2019c66e2 ]
PWM2 is commonly used to control voltage of PWM regulator of VDD_LOG in
RK3399. On the Firefly-RK3399 board, PWM2 outputs 40 KHz square wave
from power on and the VDD_LOG is about 0.9V. When the kernel boots
normally into the system, the PWM2 keeps outputing PWM signal.
But the kernel hangs randomly after "Starting kernel ..." line on that
board. When it happens, PWM2 outputs high level which causes VDD_LOG
drops to 0.4V below the normal operating voltage.
By adding "pclk_rkpwm_pmu" to the rk3399_pmucru_critical_clocks array,
PWM clock is ensured to be prepared at startup and the PWM2 output is
normal. After repeated tests, the early boot hang is gone.
This patch works on both Firefly-RK3399 and ROC-RK3399-PC boards.
Signed-off-by: Levin Du <djw@t-chip.com.cn>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mahesh Salgaonkar [Wed, 4 Jul 2018 17:57:02 +0000 (23:27 +0530)]
powerpc/pseries: Avoid using the size greater than RTAS_ERROR_LOG_MAX.
[ Upstream commit
74e96bf44f430cf7a01de19ba6cf49b361cdfd6e ]
The global mce data buffer that used to copy rtas error log is of 2048
(RTAS_ERROR_LOG_MAX) bytes in size. Before the copy we read
extended_log_length from rtas error log header, then use max of
extended_log_length and RTAS_ERROR_LOG_MAX as a size of data to be copied.
Ideally the platform (phyp) will never send extended error log with
size > 2048. But if that happens, then we have a risk of buffer overrun
and corruption. Fix this by using min_t instead.
Fixes:
d368514c3097 ("powerpc: Fix corruption when grabbing FWNMI data")
Reported-by: Michal Suchanek <msuchanek@suse.com>
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Michael Ellerman [Thu, 26 Jul 2018 12:42:44 +0000 (22:42 +1000)]
powerpc/64s: Make rfi_flush_fallback a little more robust
[ Upstream commit
78ee9946371f5848ddfc88ab1a43867df8f17d83 ]
Because rfi_flush_fallback runs immediately before the return to
userspace it currently runs with the user r1 (stack pointer). This
means if we oops in there we will report a bad kernel stack pointer in
the exception entry path, eg:
Bad kernel stack pointer
7ffff7150e40 at
c0000000000023b4
Oops: Bad kernel stack pointer, sig: 6 [#1]
LE SMP NR_CPUS=32 NUMA PowerNV
Modules linked in:
CPU: 0 PID: 1246 Comm: klogd Not tainted 4.18.0-rc2-gcc-7.3.1-00175-g0443f8a69ba3 #7
NIP:
c0000000000023b4 LR:
0000000010053e00 CTR:
0000000000000040
REGS:
c0000000fffe7d40 TRAP: 4100 Not tainted (4.18.0-rc2-gcc-7.3.1-00175-g0443f8a69ba3)
MSR:
9000000002803031 <SF,HV,VEC,VSX,FP,ME,IR,DR,LE> CR:
44000442 XER:
20000000
CFAR:
c00000000000bac8 IRQMASK:
c0000000f1e66a80
GPR00:
0000000002000000 00007ffff7150e40 00007fff93a99900 0000000000000020
...
NIP [
c0000000000023b4] rfi_flush_fallback+0x34/0x80
LR [
0000000010053e00] 0x10053e00
Although the NIP tells us where we were, and the TRAP number tells us
what happened, it would still be nicer if we could report the actual
exception rather than barfing about the stack pointer.
We an do that fairly simply by loading the kernel stack pointer on
entry and restoring the user value before returning. That way we see a
regular oops such as:
Unrecoverable exception 4100 at
c00000000000239c
Oops: Unrecoverable exception, sig: 6 [#1]
LE SMP NR_CPUS=32 NUMA PowerNV
Modules linked in:
CPU: 0 PID: 1251 Comm: klogd Not tainted 4.18.0-rc3-gcc-7.3.1-00097-g4ebfcac65acd-dirty #40
NIP:
c00000000000239c LR:
0000000010053e00 CTR:
0000000000000040
REGS:
c0000000f1e17bb0 TRAP: 4100 Not tainted (4.18.0-rc3-gcc-7.3.1-00097-g4ebfcac65acd-dirty)
MSR:
9000000002803031 <SF,HV,VEC,VSX,FP,ME,IR,DR,LE> CR:
44000442 XER:
20000000
CFAR:
c00000000000bac8 IRQMASK: 0
...
NIP [
c00000000000239c] rfi_flush_fallback+0x3c/0x80
LR [
0000000010053e00] 0x10053e00
Call Trace:
[
c0000000f1e17e30] [
c00000000000b9e4] system_call+0x5c/0x70 (unreliable)
Note this shouldn't make the kernel stack pointer vulnerable to a
meltdown attack, because it should be flushed from the cache before we
return to userspace. The user r1 value will be in the cache, because
we load it in the return path, but that is harmless.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Randy Dunlap [Sun, 15 Jul 2018 17:34:46 +0000 (10:34 -0700)]
powerpc/platforms/85xx: fix t1042rdb_diu.c build errors & warning
[ Upstream commit
f5daf77a55ef0e695cc90c440ed6503073ac5e07 ]
Fix build errors and warnings in t1042rdb_diu.c by adding header files
and MODULE_LICENSE().
../arch/powerpc/platforms/85xx/t1042rdb_diu.c:152:1: warning: data definition has no type or storage class
early_initcall(t1042rdb_diu_init);
../arch/powerpc/platforms/85xx/t1042rdb_diu.c:152:1: error: type defaults to 'int' in declaration of 'early_initcall' [-Werror=implicit-int]
../arch/powerpc/platforms/85xx/t1042rdb_diu.c:152:1: warning: parameter names (without types) in function declaration
and
WARNING: modpost: missing MODULE_LICENSE() in arch/powerpc/platforms/85xx/t1042rdb_diu.o
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Scott Wood <oss@buserror.net>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Steve French [Mon, 23 Jul 2018 14:15:18 +0000 (09:15 -0500)]
SMB3: Number of requests sent should be displayed for SMB3 not just CIFS
[ Upstream commit
289131e1f1e6ad8c661ec05e176b8f0915672059 ]
For SMB2/SMB3 the number of requests sent was not displayed
in /proc/fs/cifs/Stats unless CONFIG_CIFS_STATS2 was
enabled (only number of failed requests displayed). As
with earlier dialects, we should be displaying these
counters if CONFIG_CIFS_STATS is enabled. They
are important for debugging.
e.g. when you cat /proc/fs/cifs/Stats (before the patch)
Resources in use
CIFS Session: 1
Share (unique mount targets): 2
SMB Request/Response Buffer: 1 Pool size: 5
SMB Small Req/Resp Buffer: 1 Pool size: 30
Operations (MIDs): 0
0 session 0 share reconnects
Total vfs operations: 690 maximum at one time: 2
1) \\localhost\test
SMBs: 975
Negotiates: 0 sent 0 failed
SessionSetups: 0 sent 0 failed
Logoffs: 0 sent 0 failed
TreeConnects: 0 sent 0 failed
TreeDisconnects: 0 sent 0 failed
Creates: 0 sent 2 failed
Closes: 0 sent 0 failed
Flushes: 0 sent 0 failed
Reads: 0 sent 0 failed
Writes: 0 sent 0 failed
Locks: 0 sent 0 failed
IOCTLs: 0 sent 1 failed
Cancels: 0 sent 0 failed
Echos: 0 sent 0 failed
QueryDirectories: 0 sent 63 failed
Signed-off-by: Steve French <stfrench@microsoft.com>
Reviewed-by: Aurelien Aptel <aaptel@suse.com>
Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Steve French [Wed, 1 Aug 2018 05:56:12 +0000 (00:56 -0500)]
smb3: fix reset of bytes read and written stats
[ Upstream commit
c281bc0c7412308c7ec0888904f7c99353da4796 ]
echo 0 > /proc/fs/cifs/Stats is supposed to reset the stats
but there were four (see example below) that were not reset
(bytes read and witten, total vfs ops and max ops
at one time).
...
0 session 0 share reconnects
Total vfs operations: 100 maximum at one time: 2
1) \\localhost\test
SMBs: 0
Bytes read: 502092 Bytes written:
31457286
TreeConnects: 0 total 0 failed
TreeDisconnects: 0 total 0 failed
...
This patch fixes cifs_stats_proc_write to properly reset
those four.
Signed-off-by: Steve French <stfrench@microsoft.com>
Reviewed-by: Aurelien Aptel <aaptel@suse.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Bart Van Assche [Tue, 7 Aug 2018 23:17:29 +0000 (16:17 -0700)]
cfq: Suppress compiler warnings about comparisons
[ Upstream commit
f7ecb1b109da1006a08d5675debe60990e824432 ]
This patch does not change any functionality but avoids that gcc
reports the following warnings when building with W=1:
block/cfq-iosched.c: In function ?cfq_back_seek_max_store?:
block/cfq-iosched.c:4741:13: warning: comparison of unsigned expression < 0 is always false [-Wtype-limits]
if (__data < (MIN)) \
^
block/cfq-iosched.c:4756:1: note: in expansion of macro ?STORE_FUNCTION?
STORE_FUNCTION(cfq_back_seek_max_store, &cfqd->cfq_back_max, 0, UINT_MAX, 0);
^~~~~~~~~~~~~~
block/cfq-iosched.c: In function ?cfq_slice_idle_store?:
block/cfq-iosched.c:4741:13: warning: comparison of unsigned expression < 0 is always false [-Wtype-limits]
if (__data < (MIN)) \
^
block/cfq-iosched.c:4759:1: note: in expansion of macro ?STORE_FUNCTION?
STORE_FUNCTION(cfq_slice_idle_store, &cfqd->cfq_slice_idle, 0, UINT_MAX, 1);
^~~~~~~~~~~~~~
block/cfq-iosched.c: In function ?cfq_group_idle_store?:
block/cfq-iosched.c:4741:13: warning: comparison of unsigned expression < 0 is always false [-Wtype-limits]
if (__data < (MIN)) \
^
block/cfq-iosched.c:4760:1: note: in expansion of macro ?STORE_FUNCTION?
STORE_FUNCTION(cfq_group_idle_store, &cfqd->cfq_group_idle, 0, UINT_MAX, 1);
^~~~~~~~~~~~~~
block/cfq-iosched.c: In function ?cfq_low_latency_store?:
block/cfq-iosched.c:4741:13: warning: comparison of unsigned expression < 0 is always false [-Wtype-limits]
if (__data < (MIN)) \
^
block/cfq-iosched.c:4765:1: note: in expansion of macro ?STORE_FUNCTION?
STORE_FUNCTION(cfq_low_latency_store, &cfqd->cfq_latency, 0, 1, 0);
^~~~~~~~~~~~~~
block/cfq-iosched.c: In function ?cfq_slice_idle_us_store?:
block/cfq-iosched.c:4775:13: warning: comparison of unsigned expression < 0 is always false [-Wtype-limits]
if (__data < (MIN)) \
^
block/cfq-iosched.c:4782:1: note: in expansion of macro ?USEC_STORE_FUNCTION?
USEC_STORE_FUNCTION(cfq_slice_idle_us_store, &cfqd->cfq_slice_idle, 0, UINT_MAX);
^~~~~~~~~~~~~~~~~~~
block/cfq-iosched.c: In function ?cfq_group_idle_us_store?:
block/cfq-iosched.c:4775:13: warning: comparison of unsigned expression < 0 is always false [-Wtype-limits]
if (__data < (MIN)) \
^
block/cfq-iosched.c:4783:1: note: in expansion of macro ?USEC_STORE_FUNCTION?
USEC_STORE_FUNCTION(cfq_group_idle_us_store, &cfqd->cfq_group_idle, 0, UINT_MAX);
^~~~~~~~~~~~~~~~~~~
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
YueHaibing [Tue, 7 Aug 2018 11:34:16 +0000 (19:34 +0800)]
RDS: IB: fix 'passing zero to ERR_PTR()' warning
[ Upstream commit
5941923da29e84bc9e2a1abb2c14fffaf8d71e2f ]
Fix a static code checker warning:
net/rds/ib_frmr.c:82 rds_ib_alloc_frmr() warn: passing zero to 'ERR_PTR'
The error path for ib_alloc_mr failure should set err to PTR_ERR.
Fixes:
1659185fb4d0 ("RDS: IB: Support Fastreg MR (FRMR) memory registration mode")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Breno Leitao [Tue, 7 Aug 2018 14:15:39 +0000 (11:15 -0300)]
selftests/powerpc: Kill child processes on SIGINT
[ Upstream commit
7c27a26e1ed5a7dd709aa19685d2c98f64e1cf0c ]
There are some powerpc selftests, as tm/tm-unavailable, that run for a long
period (>120 seconds), and if it is interrupted, as pressing CRTL-C
(SIGINT), the foreground process (harness) dies but the child process and
threads continue to execute (with PPID = 1 now) in background.
In this case, you'd think the whole test exited, but there are remaining
threads and processes being executed in background. Sometimes these
zombies processes are doing annoying things, as consuming the whole CPU or
dumping things to STDOUT.
This patch fixes this problem by attaching an empty signal handler to
SIGINT in the harness process. This handler will interrupt (EINTR) the
parent process waitpid() call, letting the code to follow through the
normal flow, which will kill all the processes in the child process group.
This patch also fixes a typo.
Signed-off-by: Breno Leitao <leitao@debian.org>
Signed-off-by: Gustavo Romero <gromero@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / platform / kernel / linux-rpi.git / log