Enrico Weigelt, metux IT consult [Mon, 11 Mar 2019 13:18:20 +0000 (14:18 +0100)]
mfd: Kconfig: Pedantic formatting
Formatting of Kconfig files doesn't look so pretty, so let the
Great White Handkerchief come around and clean it up.
Signed-off-by: Enrico Weigelt, metux IT consult <info@metux.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Quentin Schulz [Thu, 21 Mar 2019 08:48:48 +0000 (16:48 +0800)]
mfd: axp20x: Add USB power supply mfd cell to AXP813
The AXP813 has a VBUS power input. Now that the axp20x_usb_power driver
supports this variant, we can add an mfd cell for it to use it.
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
[wens@csie.org: add commit message]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Tony Lindgren [Thu, 14 Feb 2019 16:03:45 +0000 (08:03 -0800)]
mfd: twl6040: Fix device init errors for ACCCTL register
I noticed that we can get a -EREMOTEIO errors on at least omap4 duovero:
twl6040 0-004b: Failed to write 2d = 19: -121
And then any following register access will produce errors.
There 2d offset above is register ACCCTL that gets written on twl6040
powerup. With error checking added to the related regcache_sync() call,
the -EREMOTEIO error is reproducable on twl6040 powerup at least
duovero.
To fix the error, we need to wait until twl6040 is accessible after the
powerup. Based on tests on omap4 duovero, we need to wait over 8ms after
powerup before register write will complete without failures. Let's also
make sure we warn about possible errors too.
Note that we have twl6040_patch[] reg_sequence with the ACCCTL register
configuration and regcache_sync() will write the new value to ACCCTL.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Fabrice Gasnier [Wed, 12 Dec 2018 08:48:14 +0000 (09:48 +0100)]
mfd: syscon: Add optional clock support
Some system control registers need to be clocked, so the registers can
be accessed. Add an optional clock and attach it to regmap.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Fabrice Gasnier [Wed, 12 Dec 2018 08:48:13 +0000 (09:48 +0100)]
dt-bindings: stm32: syscon: Add clock support
STM32 system configuration controller registers needs to be clocked.
Document clock support on stm32-syscon.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Stuart Menefy [Wed, 13 Feb 2019 22:24:02 +0000 (22:24 +0000)]
mfd: sec: Add support for the RTC on S2MPA01
The RTC portion of the S2MPA01 appears to have the same
register layout as the S2MPS14.
Signed-off-by: Stuart Menefy <stuart.menefy@mathembedded.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Stuart Menefy [Wed, 13 Feb 2019 22:24:01 +0000 (22:24 +0000)]
mfd: sec: Put one element structure initialisation on one line
Change the layout of the initialisation of structures with one
element to a single line of code. This keeps the coding style
consistent.
Signed-off-by: Stuart Menefy <stuart.menefy@mathembedded.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Yauhen Kharuzhy [Tue, 12 Feb 2019 20:59:01 +0000 (23:59 +0300)]
mfd: intel_soc_pmic_chtwc: Register LED child device
Add MFD cell for LEDs driver to the Intel Cherry Trail Whiskey Cove PMIC
mfd device driver.
Signed-off-by: Yauhen Kharuzhy <jekhor@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Lee Jones [Tue, 14 May 2019 07:09:23 +0000 (08:09 +0100)]
Merge branches 'ib-mfd-arm-leds-5.2', 'ib-mfd-gpio-input-leds-power-5.2', 'ib-mfd-pinctrl-5.2-2' and 'ib-mfd-regulator-5.2', tag 'ib-mfd-arm-net-5.2' into ibs-for-mfd-merged
Immutable branch between MFD, ARM and Net due for the 5.2 merge window
Lee Jones [Mon, 13 May 2019 06:38:04 +0000 (07:38 +0100)]
pinctrl: stmfx: Fix 'warn: bitwise AND condition is false here'
drivers/pinctrl/pinctrl-stmfx.c:441 stmfx_pinctrl_irq_set_type() warn: bitwise AND condition is false here
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Lee Jones [Mon, 13 May 2019 06:36:16 +0000 (07:36 +0100)]
pinctrl: stmfx: Fix 'warn: unsigned <VAR> is never less than zero'
smatch warnings:
drivers/pinctrl/pinctrl-stmfx.c:225 stmfx_pinconf_get() warn: unsigned 'dir' is never less than zero.
drivers/pinctrl/pinctrl-stmfx.c:228 stmfx_pinconf_get() warn: unsigned 'type' is never less than zero.
drivers/pinctrl/pinctrl-stmfx.c:231 stmfx_pinconf_get() warn: unsigned 'pupd' is never less than zero.
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Amelie Delaunay [Fri, 10 May 2019 13:39:18 +0000 (15:39 +0200)]
pinctrl: Kconfig: Fix STMFX GPIO expander Pinctrl/GPIO driver dependencies
module_i2c_driver and pinconf_generic_dt_node_to_map_pin are undeclared
if CONFIG_I2C and CONFIG_OF are not enabled.
Fixes:
1490d9f841b1 ("pinctrl: Add STMFX GPIO expander Pinctrl/GPIO driver")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Amelie Delaunay [Thu, 9 May 2019 08:58:51 +0000 (10:58 +0200)]
pinctrl: Add STMFX GPIO expander Pinctrl/GPIO driver
This patch adds pinctrl/GPIO driver for STMicroelectronics
Multi-Function eXpander (STMFX) GPIO expander.
STMFX is an I2C slave controller, offering up to 24 GPIOs.
The driver relies on generic pin config interface to configure the GPIOs.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Amelie Delaunay [Thu, 9 May 2019 08:58:50 +0000 (10:58 +0200)]
dt-bindings: pinctrl: document the STMFX pinctrl bindings
This patch adds documentation of device tree bindings for the
STMicroelectronics Multi-Function eXpander (STMFX) GPIO expander.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Amelie Delaunay [Thu, 9 May 2019 08:58:49 +0000 (10:58 +0200)]
mfd: Add ST Multi-Function eXpander (STMFX) core driver
STMicroelectronics Multi-Function eXpander (STMFX) is a slave controller
using I2C for communication with the main MCU. Main features are:
- 16 fast GPIOs individually configurable in input/output
- 8 alternate GPIOs individually configurable in input/output when other
STMFX functions are not used
- Main MCU IDD measurement
- Resistive touchscreen controller
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Amelie Delaunay [Thu, 9 May 2019 08:58:48 +0000 (10:58 +0200)]
dt-bindings: mfd: Add ST Multi-Function eXpander (STMFX) core bindings
This patch adds documentation of device tree bindings for the
STMicroelectronics Multi-Function eXpander (STMFX) MFD core.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Dmitry Osipenko [Sun, 5 May 2019 15:43:24 +0000 (18:43 +0300)]
mfd: max77620: Provide system power-off functionality
Provide system power-off functionality that allows to turn off machine
gracefully.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Dmitry Osipenko [Sun, 5 May 2019 15:43:23 +0000 (18:43 +0300)]
mfd: max77620: Support Maxim 77663
Add support for Maxim 77663 using the Max77620 driver. The hardware
is very similar to Max77663/20024, although there are couple minor
differences.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Dmitry Osipenko [Sun, 5 May 2019 15:43:22 +0000 (18:43 +0300)]
mfd: max77620: Fix swapped FPS_PERIOD_MAX_US values
The FPS_PERIOD_MAX_US definitions are swapped for MAX20024 and MAX77620,
fix it.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Dmitry Osipenko [Sun, 5 May 2019 15:43:21 +0000 (18:43 +0300)]
dt-bindings: mfd: max77620: Add system-power-controller property
Document new generic property that designates the PMIC as the system's
power controller.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Dmitry Osipenko [Sun, 5 May 2019 15:43:20 +0000 (18:43 +0300)]
dt-bindings: mfd: max77620: Add compatible for Maxim 77663
Maxim 77663 has a few minor differences in regards to hardware interface
and available capabilities by comparing it with 77620 and 20024 models,
hence re-use 77620 device-tree binding for the 77663.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Bartosz Golaszewski [Tue, 23 Apr 2019 09:04:51 +0000 (11:04 +0200)]
MAINTAINERS: Add an entry for MAX77650 PMIC driver
I plan on extending this set of drivers so add myself as maintainer.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Bartosz Golaszewski [Tue, 23 Apr 2019 09:04:50 +0000 (11:04 +0200)]
input: max77650: Add onkey support
Add support for the push- and slide-button events for max77650.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Bartosz Golaszewski [Tue, 23 Apr 2019 09:04:49 +0000 (11:04 +0200)]
leds: max77650: Add LEDs support
This adds basic support for LEDs for the max77650 PMIC. The device has
three current sinks for driving LEDs.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Bartosz Golaszewski [Tue, 23 Apr 2019 09:04:48 +0000 (11:04 +0200)]
gpio: max77650: Add GPIO support
Add GPIO support for max77650 mfd device. This PMIC exposes a single
GPIO line.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Bartosz Golaszewski [Tue, 23 Apr 2019 09:04:47 +0000 (11:04 +0200)]
power: supply: max77650: Add support for battery charger
Add basic support for the battery charger for max77650 PMIC.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Bartosz Golaszewski [Tue, 23 Apr 2019 09:04:46 +0000 (11:04 +0200)]
mfd: Add new driver for MAX77650 PMIC
Add the core MFD driver for max77650 PMIC. We define five sub-devices
for which the drivers will be added in subsequent patches.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Bartosz Golaszewski [Tue, 23 Apr 2019 09:04:45 +0000 (11:04 +0200)]
mfd: mfd-core: Document mfd_add_devices()
Add a kernel doc for mfd_add_devices().
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Bartosz Golaszewski [Tue, 23 Apr 2019 09:04:44 +0000 (11:04 +0200)]
dt-bindings: input: Add DT bindings for max77650
Add the DT binding document for the onkey module of max77650.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Bartosz Golaszewski [Tue, 23 Apr 2019 09:04:43 +0000 (11:04 +0200)]
dt-bindings: leds: Add DT bindings for max77650
Add the DT binding document for the LEDs module of max77650.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Bartosz Golaszewski [Tue, 23 Apr 2019 09:04:42 +0000 (11:04 +0200)]
dt-bindings: power: supply: Add DT bindings for max77650
Add the DT binding document for the battery charger module of max77650.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Bartosz Golaszewski [Tue, 23 Apr 2019 09:04:41 +0000 (11:04 +0200)]
dt-bindings: mfd: Add DT bindings for max77650
Add a DT binding document for max77650 ultra-low power PMIC. This
describes the core mfd device and the GPIO module.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Linus Torvalds [Mon, 6 May 2019 00:42:58 +0000 (17:42 -0700)]
Linux 5.1
Linus Torvalds [Sun, 5 May 2019 21:37:25 +0000 (14:37 -0700)]
Merge branch 'perf-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull perf fixes from Ingo Molnar:
"I'd like to apologize for this very late pull request: I was dithering
through the week whether to send the fixes, and then yesterday Jiri's
crash fix for a regression introduced in this cycle clearly marked
perf/urgent as 'must merge now'.
Most of the commits are tooling fixes, plus there's three kernel fixes
via four commits:
- race fix in the Intel PEBS code
- fix an AUX bug and roll back a previous attempt
- fix AMD family 17h generic HW cache-event perf counters
The largest diffstat contribution comes from the AMD fix - a new event
table is introduced, which is a fairly low risk change but has a large
linecount"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/x86/intel: Fix race in intel_pmu_disable_event()
perf/x86/intel/pt: Remove software double buffering PMU capability
perf/ring_buffer: Fix AUX software double buffering
perf tools: Remove needless asm/unistd.h include fixing build in some places
tools arch uapi: Copy missing unistd.h headers for arc, hexagon and riscv
tools build: Add -ldl to the disassembler-four-args feature test
perf cs-etm: Always allocate memory for cs_etm_queue::prev_packet
perf cs-etm: Don't check cs_etm_queue::prev_packet validity
perf report: Report OOM in status line in the GTK UI
perf bench numa: Add define for RUSAGE_THREAD if not present
tools lib traceevent: Change tag string for error
perf annotate: Fix build on 32 bit for BPF annotation
tools uapi x86: Sync vmx.h with the kernel
perf bpf: Return value with unlocking in perf_env__find_btf()
MAINTAINERS: Include vendor specific files under arch/*/events/*
perf/x86/amd: Update generic hardware cache events for Family 17h
Linus Torvalds [Sun, 5 May 2019 21:28:48 +0000 (14:28 -0700)]
Merge branch 'sched-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull scheduler fix from Ingo Molnar:
"Fix a kobject memory leak in the cpufreq code"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/cpufreq: Fix kobject memleak
Linus Torvalds [Sun, 5 May 2019 21:26:11 +0000 (14:26 -0700)]
Merge branch 'x86-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull x86 fix from Ingo Molnar:
"Disable function tracing during early SME setup to fix a boot crash on
SME-enabled kernels running distro kernels (some of which have
function tracing enabled)"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/mm/mem_encrypt: Disable all instrumentation for early SME setup
Linus Torvalds [Sun, 5 May 2019 16:28:45 +0000 (09:28 -0700)]
Merge branch 'fixes' of git://git./linux/kernel/git/viro/vfs
Pull vfs fixes from Al Viro:
- a couple of ->i_link use-after-free fixes
- regression fix for wrong errno on absent device name in mount(2)
(this cycle stuff)
- ancient UFS braino in large GID handling on Solaris UFS images (bogus
cut'n'paste from large UID handling; wrong field checked to decide
whether we should look at old (16bit) or new (32bit) field)
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
ufs: fix braino in ufs_get_inode_gid() for solaris UFS flavour
Abort file_remove_privs() for non-reg. files
[fix] get rid of checking for absent device name in vfs_get_tree()
apparmorfs: fix use-after-free on symlink traversal
securityfs: fix use-after-free on symlink traversal
Jiri Olsa [Sat, 4 May 2019 15:15:56 +0000 (17:15 +0200)]
perf/x86/intel: Fix race in intel_pmu_disable_event()
New race in x86_pmu_stop() was introduced by replacing the
atomic __test_and_clear_bit() of cpuc->active_mask by separate
test_bit() and __clear_bit() calls in the following commit:
3966c3feca3f ("x86/perf/amd: Remove need to check "running" bit in NMI handler")
The race causes panic for PEBS events with enabled callchains:
BUG: unable to handle kernel NULL pointer dereference at
0000000000000000
...
RIP: 0010:perf_prepare_sample+0x8c/0x530
Call Trace:
<NMI>
perf_event_output_forward+0x2a/0x80
__perf_event_overflow+0x51/0xe0
handle_pmi_common+0x19e/0x240
intel_pmu_handle_irq+0xad/0x170
perf_event_nmi_handler+0x2e/0x50
nmi_handle+0x69/0x110
default_do_nmi+0x3e/0x100
do_nmi+0x11a/0x180
end_repeat_nmi+0x16/0x1a
RIP: 0010:native_write_msr+0x6/0x20
...
</NMI>
intel_pmu_disable_event+0x98/0xf0
x86_pmu_stop+0x6e/0xb0
x86_pmu_del+0x46/0x140
event_sched_out.isra.97+0x7e/0x160
...
The event is configured to make samples from PEBS drain code,
but when it's disabled, we'll go through NMI path instead,
where data->callchain will not get allocated and we'll crash:
x86_pmu_stop
test_bit(hwc->idx, cpuc->active_mask)
intel_pmu_disable_event(event)
{
...
intel_pmu_pebs_disable(event);
...
EVENT OVERFLOW -> <NMI>
intel_pmu_handle_irq
handle_pmi_common
TEST PASSES -> test_bit(bit, cpuc->active_mask))
perf_event_overflow
perf_prepare_sample
{
...
if (!(sample_type & __PERF_SAMPLE_CALLCHAIN_EARLY))
data->callchain = perf_callchain(event, regs);
CRASH -> size += data->callchain->nr;
}
</NMI>
...
x86_pmu_disable_event(event)
}
__clear_bit(hwc->idx, cpuc->active_mask);
Fixing this by disabling the event itself before setting
off the PEBS bit.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: David Arcari <darcari@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Lendacky Thomas <Thomas.Lendacky@amd.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Fixes:
3966c3feca3f ("x86/perf/amd: Remove need to check "running" bit in NMI handler")
Link: http://lkml.kernel.org/r/20190504151556.31031-1-jolsa@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Linus Torvalds [Sat, 4 May 2019 19:24:05 +0000 (12:24 -0700)]
Merge tag 'powerpc-5.1-7' of git://git./linux/kernel/git/powerpc/linux
Pull powerpc fix from Michael Ellerman:
"One regression fix.
Changes we merged to STRICT_KERNEL_RWX on 32-bit were causing crashes
under load on some machines depending on memory layout.
Thanks to Christophe Leroy"
* tag 'powerpc-5.1-7' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/32s: Fix BATs setting with CONFIG_STRICT_KERNEL_RWX
Linus Torvalds [Fri, 3 May 2019 23:49:46 +0000 (16:49 -0700)]
Merge tag 'for-linus' of git://git./virt/kvm/kvm
Pull KVM fixes from Paolo Bonzini:
- PPC and ARM bugfixes from submaintainers
- Fix old Windows versions on AMD (recent regression)
- Fix old Linux versions on processors without EPT
- Fixes for LAPIC timer optimizations
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (21 commits)
KVM: nVMX: Fix size checks in vmx_set_nested_state
KVM: selftests: make hyperv_cpuid test pass on AMD
KVM: lapic: Check for in-kernel LAPIC before deferencing apic pointer
KVM: fix KVM_CLEAR_DIRTY_LOG for memory slots of unaligned size
x86/kvm/mmu: reset MMU context when 32-bit guest switches PAE
KVM: x86: Whitelist port 0x7e for pre-incrementing %rip
Documentation: kvm: fix dirty log ioctl arch lists
KVM: VMX: Move RSB stuffing to before the first RET after VM-Exit
KVM: arm/arm64: Don't emulate virtual timers on userspace ioctls
kvm: arm: Skip stage2 huge mappings for unaligned ipa backed by THP
KVM: arm/arm64: Ensure vcpu target is unset on reset failure
KVM: lapic: Convert guest TSC to host time domain if necessary
KVM: lapic: Allow user to disable adaptive tuning of timer advancement
KVM: lapic: Track lapic timer advance per vCPU
KVM: lapic: Disable timer advancement if adaptive tuning goes haywire
x86: kvm: hyper-v: deal with buggy TLB flush requests from WS2012
KVM: x86: Consider LAPIC TSC-Deadline timer expired if deadline too short
KVM: PPC: Book3S: Protect memslots while validating user address
KVM: PPC: Book3S HV: Perserve PSSCR FAKE_SUSPEND bit on guest exit
KVM: arm/arm64: vgic-v3: Retire pending interrupts on disabling LPIs
...
Linus Torvalds [Fri, 3 May 2019 18:42:01 +0000 (11:42 -0700)]
Merge branch 'i2c/for-current-fixed' of ssh://gitolite./linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"I2C driver bugfixes and a MAINTAINERS update for you"
* 'i2c/for-current-fixed' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: Prevent runtime suspend of adapter when Host Notify is required
i2c: synquacer: fix enumeration of slave devices
MAINTAINERS: friendly takeover of i2c-gpio driver
i2c: designware: ratelimit 'transfer when suspended' errors
i2c: imx: correct the method of getting private data in notifier_call
Linus Torvalds [Fri, 3 May 2019 16:14:07 +0000 (09:14 -0700)]
Merge tag 'drm-fixes-2019-05-03' of git://anongit.freedesktop.org/drm/drm
Pull drm fix from Dave Airlie:
"Just a single qxl revert"
* tag 'drm-fixes-2019-05-03' of git://anongit.freedesktop.org/drm/drm:
Revert "drm/qxl: drop prime import/export callbacks"
Linus Torvalds [Fri, 3 May 2019 15:55:06 +0000 (08:55 -0700)]
Merge tag 'clk-fixes-for-linus' of ssh://gitolite./linux/kernel/git/clk/linux
Pull clk fixes from Stephen Boyd:
"Two fixes for the NKMP clks on Allwinner SoCs, a locking fix for
clkdev where we forgot to hold a lock while iterating a list that can
change, and finally a build fix that adds some stubs for clk APIs that
are used by devfreq drivers on platforms without the clk APIs"
* tag 'clk-fixes-for-linus' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: Add missing stubs for a few functions
clkdev: Hold clocks_mutex while iterating clocks list
clk: sunxi-ng: nkmp: Explain why zero width check is needed
clk: sunxi-ng: nkmp: Avoid GENMASK(-1, 0)
Linus Torvalds [Fri, 3 May 2019 15:42:03 +0000 (08:42 -0700)]
Merge tag 'sound-5.1' of ssh://gitolite./linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"A few stable fixes at this round.
The USB Line6 audio fixes are a bit large, but they are rather trivial
and pretty much device-specific, so should be safe to apply at this
late stage. Ditto for other HD-audio quirks"
* tag 'sound-5.1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda/realtek - Apply the fixup for ASUS Q325UAR
ALSA: line6: use dynamic buffers
ALSA: hda/realtek - Fixed Dell AIO speaker noise
ALSA: hda/realtek - Add new Dell platform for headset mode
Alexander Shishkin [Fri, 3 May 2019 08:55:36 +0000 (11:55 +0300)]
perf/x86/intel/pt: Remove software double buffering PMU capability
Now that all AUX allocations are high-order by default, the software
double buffering PMU capability doesn't make sense any more, get rid
of it. In case some PMUs choose to opt out, we can re-introduce it.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: adrian.hunter@intel.com
Link: http://lkml.kernel.org/r/20190503085536.24119-3-alexander.shishkin@linux.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Alexander Shishkin [Fri, 3 May 2019 08:55:35 +0000 (11:55 +0300)]
perf/ring_buffer: Fix AUX software double buffering
This recent commit:
5768402fd9c6e87 ("perf/ring_buffer: Use high order allocations for AUX buffers optimistically")
overlooked the fact that the previous one page granularity of the AUX buffer
provided an implicit double buffering capability to the PMU driver, which
went away when the entire buffer became one high-order page.
Always make the full-trace mode AUX allocation at least two-part to preserve
the previous behavior and allow the implicit double buffering to continue.
Reported-by: Ammy Yi <ammy.yi@intel.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: adrian.hunter@intel.com
Fixes:
5768402fd9c6e87 ("perf/ring_buffer: Use high order allocations for AUX buffers optimistically")
Link: http://lkml.kernel.org/r/20190503085536.24119-2-alexander.shishkin@linux.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Ingo Molnar [Fri, 3 May 2019 05:48:18 +0000 (07:48 +0200)]
Merge tag 'perf-urgent-for-mingo-5.1-
20190502' of git://git./linux/kernel/git/acme/linux into perf/urgent
Pull perf/urgent fixes from Arnaldo Carvalho de Melo:
tools UAPI:
Arnaldo Carvalho de Melo:
- Sync x86's vmx.h with the kernel.
- Copy missing unistd.h headers for arc, hexagon and riscv, fixing
a reported build regression on the ARC 32-bit architecture.
perf bench numa:
Arnaldo Carvalho de Melo:
- Add define for RUSAGE_THREAD if not present, fixing the build on the
ARC architecture when only zlib and libnuma are present.
perf BPF:
Arnaldo Carvalho de Melo:
- The disassembler-four-args feature test needs -ldl on distros such as
Mageia 7.
Bo YU:
- Fix unlocking on success in perf_env__find_btf(), detected with
the coverity tool.
libtraceevent:
Leo Yan:
- Change misleading hard coded 'trace-cmd' string in error messages.
ARM hardware tracing:
Leo Yan:
- Always allocate memory for cs_etm_queue::prev_packet, fixing a segfault
when processing CoreSight perf data.
perf annotate:
Thadeu Lima de Souza Cascardo:
- Fix build on 32 bit for BPF.
perf report:
Thomas Richter:
- Report OOM in status line in the GTK UI.
core libs:
- Remove needless asm/unistd.h that, used with sys/syscall.h ended
up redefining the syscalls defines in environments such as the
ARC arch when using uClibc.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Dave Airlie [Thu, 2 May 2019 23:36:24 +0000 (09:36 +1000)]
Merge tag 'drm-misc-fixes-2019-05-02' of git://anongit.freedesktop.org/drm/drm-misc into drm-fixes
- One revert for QXL for a DRI3 breakage
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190502122529.hguztj3kncaixe3d@flea
Arnaldo Carvalho de Melo [Thu, 2 May 2019 13:26:23 +0000 (09:26 -0400)]
perf tools: Remove needless asm/unistd.h include fixing build in some places
We were including sys/syscall.h and asm/unistd.h, since sys/syscall.h
includes asm/unistd.h, sometimes this leads to the redefinition of
defines, breaking the build.
Noticed on ARC with uCLibc.
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Arnaldo Carvalho de Melo <arnaldo.melo@gmail.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Rich Felker <dalias@libc.org>
Cc: Vineet Gupta <Vineet.Gupta1@synopsys.com>
Link: https://lkml.kernel.org/n/tip-xjpf80o64i2ko74aj2jih0qg@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Arnaldo Carvalho de Melo [Mon, 22 Apr 2019 18:21:35 +0000 (15:21 -0300)]
tools arch uapi: Copy missing unistd.h headers for arc, hexagon and riscv
Since those were introduced in:
c8ce48f06503 ("asm-generic: Make time32 syscall numbers optional")
But when the asm-generic/unistd.h was sync'ed with tools/ in:
1a787fc5ba18 ("tools headers uapi: Sync copy of asm-generic/unistd.h with the kernel sources")
I forgot to copy the files for the architectures that define
__ARCH_WANT_TIME32_SYSCALLS, so the perf build was breaking there, as
reported by Vineet Gupta for the ARC architecture.
After updating my ARC container to use the glibc based toolchain + cross
building libnuma, zlib and elfutils, I finally managed to reproduce the
problem and verify that this now is fixed and will not regress as will
be tested before each pull req sent upstream.
Reported-by: Vineet Gupta <Vineet.Gupta1@synopsys.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Jiri Olsa <jolsa@kernel.org>
CC: linux-snps-arc@lists.infradead.org
Cc: Namhyung Kim <namhyung@kernel.org>
Link: https://lkml.kernel.org/r/20190426193531.GC28586@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Arnaldo Carvalho de Melo [Wed, 1 May 2019 20:27:00 +0000 (16:27 -0400)]
tools build: Add -ldl to the disassembler-four-args feature test
Thomas Backlund reported that the perf build was failing on the Mageia 7
distro, that is because it uses:
cat /tmp/build/perf/feature/test-disassembler-four-args.make.output
/usr/bin/ld: /usr/lib64/libbfd.a(plugin.o): in function `try_load_plugin':
/home/iurt/rpmbuild/BUILD/binutils-2.32/objs/bfd/../../bfd/plugin.c:243:
undefined reference to `dlopen'
/usr/bin/ld:
/home/iurt/rpmbuild/BUILD/binutils-2.32/objs/bfd/../../bfd/plugin.c:271:
undefined reference to `dlsym'
/usr/bin/ld:
/home/iurt/rpmbuild/BUILD/binutils-2.32/objs/bfd/../../bfd/plugin.c:256:
undefined reference to `dlclose'
/usr/bin/ld:
/home/iurt/rpmbuild/BUILD/binutils-2.32/objs/bfd/../../bfd/plugin.c:246:
undefined reference to `dlerror'
as we allow dynamic linking and loading
Mageia 7 uses these linker flags:
$ rpm --eval %ldflags
-Wl,--as-needed -Wl,--no-undefined -Wl,-z,relro -Wl,-O1 -Wl,--build-id -Wl,--enable-new-dtags
So add -ldl to this feature LDFLAGS.
Reported-by: Thomas Backlund <tmb@mageia.org>
Tested-by: Thomas Backlund <tmb@mageia.org>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Song Liu <songliubraving@fb.com>
Link: https://lkml.kernel.org/r/20190501173158.GC21436@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Leo Yan [Sun, 28 Apr 2019 08:32:27 +0000 (16:32 +0800)]
perf cs-etm: Always allocate memory for cs_etm_queue::prev_packet
Robert Walker reported a segmentation fault is observed when process
CoreSight trace data; this issue can be easily reproduced by the command
'perf report --itrace=i1000i' for decoding tracing data.
If neither the 'b' flag (synthesize branches events) nor 'l' flag
(synthesize last branch entries) are specified to option '--itrace',
cs_etm_queue::prev_packet will not been initialised. After merging the
code to support exception packets and sample flags, there introduced a
number of uses of cs_etm_queue::prev_packet without checking whether it
is valid, for these cases any accessing to uninitialised prev_packet
will cause crash.
As cs_etm_queue::prev_packet is used more widely now and it's already
hard to follow which functions have been called in a context where the
validity of cs_etm_queue::prev_packet has been checked, this patch
always allocates memory for cs_etm_queue::prev_packet.
Reported-by: Robert Walker <robert.walker@arm.com>
Suggested-by: Robert Walker <robert.walker@arm.com>
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Tested-by: Robert Walker <robert.walker@arm.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: Mike Leach <mike.leach@linaro.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Suzuki K Poulouse <suzuki.poulose@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Fixes:
7100b12cf474 ("perf cs-etm: Generate branch sample for exception packet")
Fixes:
24fff5eb2b93 ("perf cs-etm: Avoid stale branch samples when flush packet")
Link: http://lkml.kernel.org/r/20190428083228.20246-1-leo.yan@linaro.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Leo Yan [Sun, 28 Apr 2019 08:32:28 +0000 (16:32 +0800)]
perf cs-etm: Don't check cs_etm_queue::prev_packet validity
Since cs_etm_queue::prev_packet is allocated for all cases, it will
never be NULL pointer; now validity checking prev_packet is pointless,
remove all of them.
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Tested-by: Robert Walker <robert.walker@arm.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: Mike Leach <mike.leach@linaro.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Suzuki K Poulouse <suzuki.poulose@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Link: http://lkml.kernel.org/r/20190428083228.20246-2-leo.yan@linaro.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Thomas Richter [Tue, 23 Apr 2019 10:53:03 +0000 (12:53 +0200)]
perf report: Report OOM in status line in the GTK UI
An -ENOMEM error is not reported in the GTK GUI. Instead this error
message pops up on the screen:
[root@m35lp76 perf]# ./perf report -i perf.data.error68-1
Processing events... [974K/3M]
Error:failed to process sample
0xf4198 [0x8]: failed to process type: 68
However when I use the same perf.data file with --stdio it works:
[root@m35lp76 perf]# ./perf report -i perf.data.error68-1 --stdio \
| head -12
# Total Lost Samples: 0
#
# Samples: 76K of event 'cycles'
# Event count (approx.):
99056160000
#
# Overhead Command Shared Object Symbol
# ........ ............... ................. .........
#
8.81% find [kernel.kallsyms] [k] ftrace_likely_update
8.74% swapper [kernel.kallsyms] [k] ftrace_likely_update
8.34% sshd [kernel.kallsyms] [k] ftrace_likely_update
2.19% kworker/u512:1- [kernel.kallsyms] [k] ftrace_likely_update
The sample precentage is a bit low.....
The GUI always fails in the FINISHED_ROUND event (68) and does not
indicate the reason why.
When happened is the following. Perf report calls a lot of functions and
down deep when a FINISHED_ROUND event is processed, these functions are
called:
perf_session__process_event()
+ perf_session__process_user_event()
+ process_finished_round()
+ ordered_events__flush()
+ __ordered_events__flush()
+ do_flush()
+ ordered_events__deliver_event()
+ perf_session__deliver_event()
+ machine__deliver_event()
+ perf_evlist__deliver_event()
+ process_sample_event()
+ hist_entry_iter_add() --> only called in GUI case!!!
+ hist_iter__report__callback()
+ symbol__inc_addr_sample()
Now this functions runs out of memory and
returns -ENOMEM. This is reported all the way up
until function
perf_session__process_event() returns to its caller, where -ENOMEM is
changed to -EINVAL and processing stops:
if ((skip = perf_session__process_event(session, event, head)) < 0) {
pr_err("%#" PRIx64 " [%#x]: failed to process type: %d\n",
head, event->header.size, event->header.type);
err = -EINVAL;
goto out_err;
}
This occurred in the FINISHED_ROUND event when it has to process some
10000 entries and ran out of memory.
This patch indicates the root cause and displays it in the status line
of ther perf report GUI.
Output before (on GUI status line):
0xf4198 [0x8]: failed to process type: 68
Output after:
0xf4198 [0x8]: failed to process type: 68 [not enough memory]
Committer notes:
the 'skip' variable needs to be initialized to -EINVAL, so that when the
size is less than sizeof(struct perf_event_attr) we avoid this valid
compiler warning:
util/session.c: In function ‘perf_session__process_events’:
util/session.c:1936:7: error: ‘skip’ may be used uninitialized in this function [-Werror=maybe-uninitialized]
err = skip;
~~~~^~~~~~
util/session.c:1874:6: note: ‘skip’ was declared here
s64 skip;
^~~~
cc1: all warnings being treated as errors
Signed-off-by: Thomas Richter <tmricht@linux.ibm.com>
Reviewed-by: Hendrik Brueckner <brueckner@linux.ibm.com>
Reviewed-by: Jiri Olsa <jolsa@redhat.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Link: http://lkml.kernel.org/r/20190423105303.61683-1-tmricht@linux.ibm.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Arnaldo Carvalho de Melo [Thu, 25 Apr 2019 21:36:51 +0000 (18:36 -0300)]
perf bench numa: Add define for RUSAGE_THREAD if not present
While cross building perf to the ARC architecture on a fedora 30 host,
we were failing with:
CC /tmp/build/perf/bench/numa.o
bench/numa.c: In function ‘worker_thread’:
bench/numa.c:1261:12: error: ‘RUSAGE_THREAD’ undeclared (first use in this function); did you mean ‘SIGEV_THREAD’?
getrusage(RUSAGE_THREAD, &rusage);
^~~~~~~~~~~~~
SIGEV_THREAD
bench/numa.c:1261:12: note: each undeclared identifier is reported only once for each function it appears in
[perfbuilder@
60d5802468f6 perf]$ /arc_gnu_2019.03-rc1_prebuilt_uclibc_le_archs_linux_install/bin/arc-linux-gcc --version | head -1
arc-linux-gcc (ARCv2 ISA Linux uClibc toolchain 2019.03-rc1) 8.3.1
20190225
[perfbuilder@
60d5802468f6 perf]$
Trying to reproduce a report by Vineet, I noticed that, with just
cross-built zlib and numactl libraries, I ended up with the above
failure.
So, since RUSAGE_THREAD is available as a define, check for that and
numactl libraries, I ended up with the above failure.
So, since RUSAGE_THREAD is available as a define in the system headers,
check if it is defined in the 'perf bench numa' sources and define it if
not.
Now it builds and I have to figure out if the problem reported by Vineet
only takes place if we have libelf or some other library available.
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: linux-snps-arc@lists.infradead.org
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Vineet Gupta <Vineet.Gupta1@synopsys.com>
Link: https://lkml.kernel.org/n/tip-2wb4r1gir9xrevbpq7qp0amk@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Leo Yan [Wed, 24 Apr 2019 01:38:02 +0000 (09:38 +0800)]
tools lib traceevent: Change tag string for error
The traceevent lib is used by the perf tool, and when executing
perf test -v 6
it outputs error log on the ARM64 platform:
running test 33 '*:*'trace-cmd: No such file or directory
[...]
trace-cmd: Invalid argument
The trace event parsing code originally came from trace-cmd so it keeps
the tag string "trace-cmd" for errors, this easily introduces the
impression that the perf tool launches trace-cmd command for trace event
parsing, but in fact the related parsing is accomplished by the
traceevent lib.
This patch changes the tag string to "libtraceevent" so that we can
avoid confusion and let users to more easily connect the error with
traceevent lib.
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Acked-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Link: http://lkml.kernel.org/r/20190424013802.27569-1-leo.yan@linaro.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Thadeu Lima de Souza Cascardo [Wed, 3 Apr 2019 19:44:52 +0000 (16:44 -0300)]
perf annotate: Fix build on 32 bit for BPF annotation
Commit
6987561c9e86 ("perf annotate: Enable annotation of BPF programs") adds
support for BPF programs annotations but the new code does not build on 32-bit.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Acked-by: Song Liu <songliubraving@fb.com>
Fixes:
6987561c9e86 ("perf annotate: Enable annotation of BPF programs")
Link: http://lkml.kernel.org/r/20190403194452.10845-1-cascardo@canonical.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Arnaldo Carvalho de Melo [Mon, 22 Apr 2019 14:54:50 +0000 (11:54 -0300)]
tools uapi x86: Sync vmx.h with the kernel
To pick up the changes from:
2b27924bb1d4 ("KVM: nVMX: always use early vmcs check when EPT is disabled")
That causes this object in the tools/perf build process to be rebuilt:
CC /tmp/build/perf/arch/x86/util/kvm-stat.o
But it isn't using VMX_ABORT_ prefixed constants, so no change in
behaviour.
This silences this perf build warning:
Warning: Kernel ABI header at 'tools/arch/x86/include/uapi/asm/vmx.h' differs from latest version at 'arch/x86/include/uapi/asm/vmx.h'
diff -u tools/arch/x86/include/uapi/asm/vmx.h arch/x86/include/uapi/asm/vmx.h
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Link: https://lkml.kernel.org/n/tip-bjbo3zc0r8i8oa0udpvftya6@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Bo YU [Mon, 22 Apr 2019 08:01:38 +0000 (04:01 -0400)]
perf bpf: Return value with unlocking in perf_env__find_btf()
In perf_env__find_btf(), we're returning without unlocking
"env->bpf_progs.lock". There may be cause lockdep issue.
Detected by CoversityScan, CID# 1444762:(program hangs(LOCK))
Signed-off-by: Bo YU <tsu.yubo@gmail.com>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Martin KaFai Lau <kafai@fb.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Song Liu <songliubraving@fb.com>
Cc: Yonghong Song <yhs@fb.com>
Cc: bpf@vger.kernel.org
Cc: netdev@vger.kernel.org
Fixes:
2db7b1e0bd49d: (perf bpf: Return NULL when RB tree lookup fails in perf_env__find_btf())
Link: http://lkml.kernel.org/r/20190422080138.10088-1-tsu.yubo@gmail.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Linus Torvalds [Thu, 2 May 2019 18:03:34 +0000 (11:03 -0700)]
Merge git://git./linux/kernel/git/davem/net
Pull networking fixes from David Miller:
1) Out of bounds access in xfrm IPSEC policy unlink, from Yue Haibing.
2) Missing length check for esp4 UDP encap, from Sabrina Dubroca.
3) Fix byte order of RX STBC access in mac80211, from Johannes Berg.
4) Inifnite loop in bpftool map create, from Alban Crequy.
5) Register mark fix in ebpf verifier after pkt/null checks, from Paul
Chaignon.
6) Properly use rcu_dereference_sk_user_data in L2TP code, from Eric
Dumazet.
7) Buffer overrun in marvell phy driver, from Andrew Lunn.
8) Several crash and statistics handling fixes to bnxt_en driver, from
Michael Chan and Vasundhara Volam.
9) Several fixes to the TLS layer from Jakub Kicinski (copying negative
amounts of data in reencrypt, reencrypt frag copying, blind nskb->sk
NULL deref, etc).
10) Several UDP GRO fixes, from Paolo Abeni and Eric Dumazet.
11) PID/UID checks on ipv6 flow labels are inverted, from Willem de
Bruijn.
12) Use after free in l2tp, from Eric Dumazet.
13) IPV6 route destroy races, also from Eric Dumazet.
14) SCTP state machine can erroneously run recursively, fix from Xin
Long.
15) Adjust AF_PACKET msg_name length checks, add padding bytes if
necessary. From Willem de Bruijn.
16) Preserve skb_iif, so that forwarded packets have consistent values
even if fragmentation is involved. From Shmulik Ladkani.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (69 commits)
udp: fix GRO packet of death
ipv6: A few fixes on dereferencing rt->from
rds: ib: force endiannes annotation
selftests: fib_rule_tests: print the result and return 1 if any tests failed
ipv4: ip_do_fragment: Preserve skb_iif during fragmentation
net/tls: avoid NULL pointer deref on nskb->sk in fallback
selftests: fib_rule_tests: Fix icmp proto with ipv6
packet: validate msg_namelen in send directly
packet: in recvmsg msg_name return at least sizeof sockaddr_ll
sctp: avoid running the sctp state machine recursively
stmmac: pci: Fix typo in IOT2000 comment
Documentation: fix netdev-FAQ.rst markup warning
ipv6: fix races in ip6_dst_destroy()
l2ip: fix possible use-after-free
appletalk: Set error code if register_snap_client failed
net: dsa: bcm_sf2: fix buffer overflow doing set_rxnfc
rxrpc: Fix net namespace cleanup
ipv6/flowlabel: wait rcu grace period before put_pid()
vrf: Use orig netdev to count Ip6InNoRoutes and a fresh route lookup when sending dest unreach
tcp: add sanity tests in tcp_add_backlog()
...
Linus Torvalds [Thu, 2 May 2019 16:55:04 +0000 (09:55 -0700)]
Merge tag 'for-linus-
20190502' of git://git.kernel.dk/linux-block
Pull io_uring fixes from Jens Axboe:
"This is mostly io_uring fixes/tweaks. Most of these were actually done
in time for the last -rc, but I wanted to ensure that everything
tested out great before including them. The code delta looks larger
than it really is, as it's mostly just comment additions/changes.
Outside of the comment additions/changes, this is mostly removal of
unnecessary barriers. In all, this pull request contains:
- Tweak to how we handle errors at submission time. We now post a
completion event if the error occurs on behalf of an sqe, instead
of returning it through the system call. If the error happens
outside of a specific sqe, we return the error through the system
call. This makes it nicer to use and makes the "normal" use case
behave the same as the offload cases. (me)
- Fix for a missing req reference drop from async context (me)
- If an sqe is submitted with RWF_NOWAIT, don't punt it to async
context. Return -EAGAIN directly, instead of using it as a hint to
do async punt. (Stefan)
- Fix notes on barriers (Stefan)
- Remove unnecessary barriers (Stefan)
- Fix potential double free of memory in setup error (Mark)
- Further improve sq poll CPU validation (Mark)
- Fix page allocation warning and leak on buffer registration error
(Mark)
- Fix iov_iter_type() for new no-ref flag (Ming)
- Fix a case where dio doesn't honor bio no-page-ref (Ming)"
* tag 'for-linus-
20190502' of git://git.kernel.dk/linux-block:
io_uring: avoid page allocation warnings
iov_iter: fix iov_iter_type
block: fix handling for BIO_NO_PAGE_REF
io_uring: drop req submit reference always in async punt
io_uring: free allocated io_memory once
io_uring: fix SQPOLL cpu validation
io_uring: have submission side sqe errors post a cqe
io_uring: remove unnecessary barrier after unsetting IORING_SQ_NEED_WAKEUP
io_uring: remove unnecessary barrier after incrementing dropped counter
io_uring: remove unnecessary barrier before reading SQ tail
io_uring: remove unnecessary barrier after updating SQ head
io_uring: remove unnecessary barrier before reading cq head
io_uring: remove unnecessary barrier before wq_has_sleeper
io_uring: fix notes on barriers
io_uring: fix handling SQEs requesting NOWAIT
Jarkko Nikula [Tue, 30 Apr 2019 14:23:22 +0000 (17:23 +0300)]
i2c: Prevent runtime suspend of adapter when Host Notify is required
Multiple users have reported their Synaptics touchpad has stopped
working between v4.20.1 and v4.20.2 when using SMBus interface.
The culprit for this appeared to be commit
c5eb1190074c ("PCI / PM: Allow
runtime PM without callback functions") that fixed the runtime PM for
i2c-i801 SMBus adapter. Those Synaptics touchpad are using i2c-i801
for SMBus communication and testing showed they are able to get back
working by preventing the runtime suspend of adapter.
Normally when i2c-i801 SMBus adapter transmits with the client it resumes
before operation and autosuspends after.
However, if client requires SMBus Host Notify protocol, what those
Synaptics touchpads do, then the host adapter must not go to runtime
suspend since then it cannot process incoming SMBus Host Notify commands
the client may send.
Fix this by keeping I2C/SMBus adapter active in case client requires
Host Notify.
Reported-by: Keijo Vaara <ferdasyn@rocketmail.com>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=203297
Fixes:
c5eb1190074c ("PCI / PM: Allow runtime PM without callback functions")
Cc: stable@vger.kernel.org # v4.20+
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Keijo Vaara <ferdasyn@rocketmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Ard Biesheuvel [Tue, 30 Apr 2019 09:47:34 +0000 (11:47 +0200)]
i2c: synquacer: fix enumeration of slave devices
The I2C host driver for SynQuacer fails to populate the of_node and
ACPI companion fields of the struct i2c_adapter it instantiates,
resulting in enumeration of the subordinate I2C bus to fail.
Fixes:
0d676a6c4390 ("i2c: add support for Socionext SynQuacer I2C controller")
Cc: <stable@vger.kernel.org> # v4.19+
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Wolfram Sang [Thu, 25 Apr 2019 14:35:55 +0000 (16:35 +0200)]
MAINTAINERS: friendly takeover of i2c-gpio driver
I haven't heard from Haavard in years despite putting him to the CC list for
i2c-gpio related mails. Since I was doing the work on this driver for a while
now, let me take official maintainership, so it will be more clear to users.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Haavard Skinnemoen <hskinnemoen@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Kim Phillips [Thu, 2 May 2019 15:58:37 +0000 (15:58 +0000)]
MAINTAINERS: Include vendor specific files under arch/*/events/*
Add an explicit subdirectory specification for arch/x86/events/amd to
the MAINTAINERS file, to distinguish it from its parent. This will
produce the correct set of maintainers for the files found therein.
Signed-off-by: Kim Phillips <kim.phillips@amd.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Gary Hook <Gary.Hook@amd.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Janakarajan Natarajan <Janakarajan.Natarajan@amd.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Martin Liška <mliska@suse.cz>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Pu Wen <puwen@hygon.cn>
Cc: Stephane Eranian <eranian@google.com>
Cc: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Thomas Lendacky <Thomas.Lendacky@amd.com>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: linux-kernel@vger.kernel.org
Fixes:
39b0332a2158 ("perf/x86: Move perf_event_amd.c ........... => x86/events/amd/core.c")
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Kim Phillips [Thu, 2 May 2019 15:29:47 +0000 (15:29 +0000)]
perf/x86/amd: Update generic hardware cache events for Family 17h
Add a new amd_hw_cache_event_ids_f17h assignment structure set
for AMD families 17h and above, since a lot has changed. Specifically:
L1 Data Cache
The data cache access counter remains the same on Family 17h.
For DC misses, PMCx041's definition changes with Family 17h,
so instead we use the L2 cache accesses from L1 data cache
misses counter (PMCx060,umask=0xc8).
For DC hardware prefetch events, Family 17h breaks compatibility
for PMCx067 "Data Prefetcher", so instead, we use PMCx05a "Hardware
Prefetch DC Fills."
L1 Instruction Cache
PMCs 0x80 and 0x81 (32-byte IC fetches and misses) are backward
compatible on Family 17h.
For prefetches, we remove the erroneous PMCx04B assignment which
counts how many software data cache prefetch load instructions were
dispatched.
LL - Last Level Cache
Removing PMCs 7D, 7E, and 7F assignments, as they do not exist
on Family 17h, where the last level cache is L3. L3 counters
can be accessed using the existing AMD Uncore driver.
Data TLB
On Intel machines, data TLB accesses ("dTLB-loads") are assigned
to counters that count load/store instructions retired. This
is inconsistent with instruction TLB accesses, where Intel
implementations report iTLB misses that hit in the STLB.
Ideally, dTLB-loads would count higher level dTLB misses that hit
in lower level TLBs, and dTLB-load-misses would report those
that also missed in those lower-level TLBs, therefore causing
a page table walk. That would be consistent with instruction
TLB operation, remove the redundancy between dTLB-loads and
L1-dcache-loads, and prevent perf from producing artificially
low percentage ratios, i.e. the "0.01%" below:
42,550,869 L1-dcache-loads
41,591,860 dTLB-loads
4,802 dTLB-load-misses # 0.01% of all dTLB cache hits
7,283,682 L1-dcache-stores
7,912,392 dTLB-stores
310 dTLB-store-misses
On AMD Families prior to 17h, the "Data Cache Accesses" counter is
used, which is slightly better than load/store instructions retired,
but still counts in terms of individual load/store operations
instead of TLB operations.
So, for AMD Families 17h and higher, this patch assigns "dTLB-loads"
to a counter for L1 dTLB misses that hit in the L2 dTLB, and
"dTLB-load-misses" to a counter for L1 DTLB misses that caused
L2 DTLB misses and therefore also caused page table walks. This
results in a much more accurate view of data TLB performance:
60,961,781 L1-dcache-loads
4,601 dTLB-loads
963 dTLB-load-misses # 20.93% of all dTLB cache hits
Note that for all AMD families, data loads and stores are combined
in a single accesses counter, so no 'L1-dcache-stores' are reported
separately, and stores are counted with loads in 'L1-dcache-loads'.
Also note that the "% of all dTLB cache hits" string is misleading
because (a) "dTLB cache": although TLBs can be considered caches for
page tables, in this context, it can be misinterpreted as data cache
hits because the figures are similar (at least on Intel), and (b) not
all those loads (technically accesses) technically "hit" at that
hardware level. "% of all dTLB accesses" would be more clear/accurate.
Instruction TLB
On Intel machines, 'iTLB-loads' measure iTLB misses that hit in the
STLB, and 'iTLB-load-misses' measure iTLB misses that also missed in
the STLB and completed a page table walk.
For AMD Family 17h and above, for 'iTLB-loads' we replace the
erroneous instruction cache fetches counter with PMCx084
"L1 ITLB Miss, L2 ITLB Hit".
For 'iTLB-load-misses' we still use PMCx085 "L1 ITLB Miss,
L2 ITLB Miss", but set a 0xff umask because without it the event
does not get counted.
Branch Predictor (BPU)
PMCs 0xc2 and 0xc3 continue to be valid across all AMD Families.
Node Level Events
Family 17h does not have a PMCx0e9 counter, and corresponding counters
have not been made available publicly, so for now, we mark them as
unsupported for Families 17h and above.
Reference:
"Open-Source Register Reference For AMD Family 17h Processors Models 00h-2Fh"
Released 7/17/2018, Publication #56255, Revision 3.03:
https://www.amd.com/system/files/TechDocs/56255_OSRR.pdf
[ mingo: tidied up the line breaks. ]
Signed-off-by: Kim Phillips <kim.phillips@amd.com>
Cc: <stable@vger.kernel.org> # v4.9+
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Janakarajan Natarajan <Janakarajan.Natarajan@amd.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Martin Liška <mliska@suse.cz>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Pu Wen <puwen@hygon.cn>
Cc: Stephane Eranian <eranian@google.com>
Cc: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Thomas Lendacky <Thomas.Lendacky@amd.com>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: linux-kernel@vger.kernel.org
Cc: linux-perf-users@vger.kernel.org
Fixes:
e40ed1542dd7 ("perf/x86: Add perf support for AMD family-17h processors")
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Wolfram Sang [Wed, 24 Apr 2019 16:16:32 +0000 (18:16 +0200)]
i2c: designware: ratelimit 'transfer when suspended' errors
There are two problems with dev_err() here. One: It is not ratelimited.
Two: We don't see which driver tried to transfer something with a
suspended adapter. Switch to dev_WARN_ONCE to fix both issues. Drawback
is that we don't see if multiple drivers are trying to transfer while
suspended. They need to be discovered one after the other now. This is
better than a high CPU load because a really broken driver might try to
resend endlessly.
Link: https://bugs.archlinux.org/task/62391
Fixes:
275154155538 ("i2c: designware: Do not allow i2c_dw_xfer() calls while suspended")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reported-by: skidnik <skidnik@gmail.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: skidnik <skidnik@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Linus Torvalds [Thu, 2 May 2019 15:29:24 +0000 (08:29 -0700)]
Merge tag 'pci-v5.1-fixes-3' of git://git./linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
"I apologize for sending these so late in the cycle. We went back and
forth about how to deal with the unexpected logging of intentional
link state changes and finally decided to just config them off by
default.
PCI fixes:
- Stop ignoring "pci=disable_acs_redir" parameter (Logan Gunthorpe)
- Use shared MSI/MSI-X vector for Link Bandwidth Management (Alex
Williamson)
- Add Kconfig option for Link Bandwidth notification messages (Keith
Busch)"
* tag 'pci-v5.1-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI/LINK: Add Kconfig option (default off)
PCI/portdrv: Use shared MSI/MSI-X vector for Bandwidth Management
PCI: Fix issue with "pci=disable_acs_redir" parameter being ignored
Linus Torvalds [Thu, 2 May 2019 15:27:39 +0000 (08:27 -0700)]
Merge tag 'mtd/fixes-for-5.1-rc6' of git://git./linux/kernel/git/mtd/linux
Pull MTD fix from Richard Weinberger:
"A single regression fix for the marvell nand driver"
* tag 'mtd/fixes-for-5.1-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux:
mtd: rawnand: marvell: Clean the controller state before each operation
Keith Busch [Wed, 1 May 2019 14:29:42 +0000 (08:29 -0600)]
PCI/LINK: Add Kconfig option (default off)
e8303bb7a75c ("PCI/LINK: Report degraded links via link bandwidth
notification") added dmesg logging whenever a link changes speed or width
to a state that is considered degraded. Unfortunately, it cannot
differentiate signal integrity-related link changes from those
intentionally initiated by an endpoint driver, including drivers that may
live in userspace or VMs when making use of vfio-pci. Some GPU drivers
actively manage the link state to save power, which generates a stream of
messages like this:
vfio-pci 0000:07:00.0: 32.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s x16 link at 0000:00:02.0 (capable of 64.000 Gb/s with 5 GT/s x16 link)
Since we can't distinguish the intentional changes from the signal
integrity issues, leave the reporting turned off by default. Add a Kconfig
option to turn it on if desired.
Fixes:
e8303bb7a75c ("PCI/LINK: Report degraded links via link bandwidth notification")
Link: https://lore.kernel.org/linux-pci/20190501142942.26972-1-keith.busch@intel.com
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Al Viro [Thu, 2 May 2019 02:46:11 +0000 (22:46 -0400)]
ufs: fix braino in ufs_get_inode_gid() for solaris UFS flavour
To choose whether to pick the GID from the old (16bit) or new (32bit)
field, we should check if the old gid field is set to 0xffff. Mainline
checks the old *UID* field instead - cut'n'paste from the corresponding
code in ufs_get_inode_uid().
Fixes:
252e211e90ce
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Christophe Leroy [Tue, 30 Apr 2019 16:11:59 +0000 (16:11 +0000)]
powerpc/32s: Fix BATs setting with CONFIG_STRICT_KERNEL_RWX
Serge reported some crashes with CONFIG_STRICT_KERNEL_RWX enabled
on a book3s32 machine.
Analysis shows two issues:
- BATs addresses and sizes are not properly aligned.
- There is a gap between the last address covered by BATs and the
first address covered by pages.
Memory mapped with DBATs:
0: 0xc0000000-0xc07fffff 0x00000000 Kernel RO coherent
1: 0xc0800000-0xc0bfffff 0x00800000 Kernel RO coherent
2: 0xc0c00000-0xc13fffff 0x00c00000 Kernel RW coherent
3: 0xc1400000-0xc23fffff 0x01400000 Kernel RW coherent
4: 0xc2400000-0xc43fffff 0x02400000 Kernel RW coherent
5: 0xc4400000-0xc83fffff 0x04400000 Kernel RW coherent
6: 0xc8400000-0xd03fffff 0x08400000 Kernel RW coherent
7: 0xd0400000-0xe03fffff 0x10400000 Kernel RW coherent
Memory mapped with pages:
0xe1000000-0xefffffff 0x21000000 240M rw present dirty accessed
This patch fixes both issues. With the patch, we get the following
which is as expected:
Memory mapped with DBATs:
0: 0xc0000000-0xc07fffff 0x00000000 Kernel RO coherent
1: 0xc0800000-0xc0bfffff 0x00800000 Kernel RO coherent
2: 0xc0c00000-0xc0ffffff 0x00c00000 Kernel RW coherent
3: 0xc1000000-0xc1ffffff 0x01000000 Kernel RW coherent
4: 0xc2000000-0xc3ffffff 0x02000000 Kernel RW coherent
5: 0xc4000000-0xc7ffffff 0x04000000 Kernel RW coherent
6: 0xc8000000-0xcfffffff 0x08000000 Kernel RW coherent
7: 0xd0000000-0xdfffffff 0x10000000 Kernel RW coherent
Memory mapped with pages:
0xe0000000-0xefffffff 0x20000000 256M rw present dirty accessed
Fixes:
63b2bc619565 ("powerpc/mm/32s: Use BATs for STRICT_KERNEL_RWX")
Reported-by: Serge Belyshev <belyshev@depni.sinp.msu.ru>
Acked-by: Segher Boessenkool <segher@kernel.crashing.org>
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Eric Dumazet [Thu, 2 May 2019 01:56:28 +0000 (18:56 -0700)]
udp: fix GRO packet of death
syzbot was able to crash host by sending UDP packets with a 0 payload.
TCP does not have this issue since we do not aggregate packets without
payload.
Since dev_gro_receive() sets gso_size based on skb_gro_len(skb)
it seems not worth trying to cope with padded packets.
BUG: KASAN: slab-out-of-bounds in skb_gro_receive+0xf5f/0x10e0 net/core/skbuff.c:3826
Read of size 16 at addr
ffff88808893fff0 by task syz-executor612/7889
CPU: 0 PID: 7889 Comm: syz-executor612 Not tainted 5.1.0-rc7+ #96
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x172/0x1f0 lib/dump_stack.c:113
print_address_description.cold+0x7c/0x20d mm/kasan/report.c:187
kasan_report.cold+0x1b/0x40 mm/kasan/report.c:317
__asan_report_load16_noabort+0x14/0x20 mm/kasan/generic_report.c:133
skb_gro_receive+0xf5f/0x10e0 net/core/skbuff.c:3826
udp_gro_receive_segment net/ipv4/udp_offload.c:382 [inline]
call_gro_receive include/linux/netdevice.h:2349 [inline]
udp_gro_receive+0xb61/0xfd0 net/ipv4/udp_offload.c:414
udp4_gro_receive+0x763/0xeb0 net/ipv4/udp_offload.c:478
inet_gro_receive+0xe72/0x1110 net/ipv4/af_inet.c:1510
dev_gro_receive+0x1cd0/0x23c0 net/core/dev.c:5581
napi_gro_frags+0x36b/0xd10 net/core/dev.c:5843
tun_get_user+0x2f24/0x3fb0 drivers/net/tun.c:1981
tun_chr_write_iter+0xbd/0x156 drivers/net/tun.c:2027
call_write_iter include/linux/fs.h:1866 [inline]
do_iter_readv_writev+0x5e1/0x8e0 fs/read_write.c:681
do_iter_write fs/read_write.c:957 [inline]
do_iter_write+0x184/0x610 fs/read_write.c:938
vfs_writev+0x1b3/0x2f0 fs/read_write.c:1002
do_writev+0x15e/0x370 fs/read_write.c:1037
__do_sys_writev fs/read_write.c:1110 [inline]
__se_sys_writev fs/read_write.c:1107 [inline]
__x64_sys_writev+0x75/0xb0 fs/read_write.c:1107
do_syscall_64+0x103/0x610 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x49/0xbe
RIP: 0033:0x441cc0
Code: 05 48 3d 01 f0 ff ff 0f 83 9d 09 fc ff c3 66 2e 0f 1f 84 00 00 00 00 00 66 90 83 3d 51 93 29 00 00 75 14 b8 14 00 00 00 0f 05 <48> 3d 01 f0 ff ff 0f 83 74 09 fc ff c3 48 83 ec 08 e8 ba 2b 00 00
RSP: 002b:
00007ffe8c716118 EFLAGS:
00000246 ORIG_RAX:
0000000000000014
RAX:
ffffffffffffffda RBX:
00007ffe8c716150 RCX:
0000000000441cc0
RDX:
0000000000000001 RSI:
00007ffe8c716170 RDI:
00000000000000f0
RBP:
0000000000000000 R08:
000000000000ffff R09:
0000000000a64668
R10:
0000000020000040 R11:
0000000000000246 R12:
000000000000c2d9
R13:
0000000000402b50 R14:
0000000000000000 R15:
0000000000000000
Allocated by task 5143:
save_stack+0x45/0xd0 mm/kasan/common.c:75
set_track mm/kasan/common.c:87 [inline]
__kasan_kmalloc mm/kasan/common.c:497 [inline]
__kasan_kmalloc.constprop.0+0xcf/0xe0 mm/kasan/common.c:470
kasan_slab_alloc+0xf/0x20 mm/kasan/common.c:505
slab_post_alloc_hook mm/slab.h:437 [inline]
slab_alloc mm/slab.c:3393 [inline]
kmem_cache_alloc+0x11a/0x6f0 mm/slab.c:3555
mm_alloc+0x1d/0xd0 kernel/fork.c:1030
bprm_mm_init fs/exec.c:363 [inline]
__do_execve_file.isra.0+0xaa3/0x23f0 fs/exec.c:1791
do_execveat_common fs/exec.c:1865 [inline]
do_execve fs/exec.c:1882 [inline]
__do_sys_execve fs/exec.c:1958 [inline]
__se_sys_execve fs/exec.c:1953 [inline]
__x64_sys_execve+0x8f/0xc0 fs/exec.c:1953
do_syscall_64+0x103/0x610 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x49/0xbe
Freed by task 5351:
save_stack+0x45/0xd0 mm/kasan/common.c:75
set_track mm/kasan/common.c:87 [inline]
__kasan_slab_free+0x102/0x150 mm/kasan/common.c:459
kasan_slab_free+0xe/0x10 mm/kasan/common.c:467
__cache_free mm/slab.c:3499 [inline]
kmem_cache_free+0x86/0x260 mm/slab.c:3765
__mmdrop+0x238/0x320 kernel/fork.c:677
mmdrop include/linux/sched/mm.h:49 [inline]
finish_task_switch+0x47b/0x780 kernel/sched/core.c:2746
context_switch kernel/sched/core.c:2880 [inline]
__schedule+0x81b/0x1cc0 kernel/sched/core.c:3518
preempt_schedule_irq+0xb5/0x140 kernel/sched/core.c:3745
retint_kernel+0x1b/0x2d
arch_local_irq_restore arch/x86/include/asm/paravirt.h:767 [inline]
kmem_cache_free+0xab/0x260 mm/slab.c:3766
anon_vma_chain_free mm/rmap.c:134 [inline]
unlink_anon_vmas+0x2ba/0x870 mm/rmap.c:401
free_pgtables+0x1af/0x2f0 mm/memory.c:394
exit_mmap+0x2d1/0x530 mm/mmap.c:3144
__mmput kernel/fork.c:1046 [inline]
mmput+0x15f/0x4c0 kernel/fork.c:1067
exec_mmap fs/exec.c:1046 [inline]
flush_old_exec+0x8d9/0x1c20 fs/exec.c:1279
load_elf_binary+0x9bc/0x53f0 fs/binfmt_elf.c:864
search_binary_handler fs/exec.c:1656 [inline]
search_binary_handler+0x17f/0x570 fs/exec.c:1634
exec_binprm fs/exec.c:1698 [inline]
__do_execve_file.isra.0+0x1394/0x23f0 fs/exec.c:1818
do_execveat_common fs/exec.c:1865 [inline]
do_execve fs/exec.c:1882 [inline]
__do_sys_execve fs/exec.c:1958 [inline]
__se_sys_execve fs/exec.c:1953 [inline]
__x64_sys_execve+0x8f/0xc0 fs/exec.c:1953
do_syscall_64+0x103/0x610 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x49/0xbe
The buggy address belongs to the object at
ffff88808893f7c0
which belongs to the cache mm_struct of size 1496
The buggy address is located 600 bytes to the right of
1496-byte region [
ffff88808893f7c0,
ffff88808893fd98)
The buggy address belongs to the page:
page:
ffffea0002224f80 count:1 mapcount:0 mapping:
ffff88821bc40ac0 index:0xffff88808893f7c0 compound_mapcount: 0
flags: 0x1fffc0000010200(slab|head)
raw:
01fffc0000010200 ffffea00025b4f08 ffffea00027b9d08 ffff88821bc40ac0
raw:
ffff88808893f7c0 ffff88808893e440 0000000100000001 0000000000000000
page dumped because: kasan: bad access detected
Memory state around the buggy address:
ffff88808893fe80: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
ffff88808893ff00: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
>
ffff88808893ff80: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
^
ffff888088940000: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
ffff888088940080: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
Fixes:
e20cf8d3f1f7 ("udp: implement GRO for plain UDP sockets.")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Paolo Abeni <pabeni@redhat.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Wed, 1 May 2019 21:57:23 +0000 (14:57 -0700)]
Merge tag 'for-v5.1-rc' of git://git./linux/kernel/git/sre/linux-power-supply
Pull power supply fixes from Sebastian Reichel:
"Two more fixes for the 5.1 cycle.
One division by zero fix in a specific driver and one core workaround
for bad userspace behaviour from systemd regarding uevents. IMHO this
can be considered to be a userspace bug, but the debug messages are
useless anyways
- cpcap-battery: fix a division by zero
- core: fix systemd issue due to log messages produced by uevent"
* tag 'for-v5.1-rc' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply:
power: supply: sysfs: prevent endless uevent loop with CONFIG_POWER_SUPPLY_DEBUG
power: supply: cpcap-battery: Fix division by zero
Martin KaFai Lau [Tue, 30 Apr 2019 17:45:12 +0000 (10:45 -0700)]
ipv6: A few fixes on dereferencing rt->from
It is a followup after the fix in
commit
9c69a1320515 ("route: Avoid crash from dereferencing NULL rt->from")
rt6_do_redirect():
1. NULL checking is needed on rt->from because a parallel
fib6_info delete could happen that sets rt->from to NULL.
(e.g. rt6_remove_exception() and fib6_drop_pcpu_from()).
2. fib6_info_hold() is not enough. Same reason as (1).
Meaning, holding dst->__refcnt cannot ensure
rt->from is not NULL or rt->from->fib6_ref is not 0.
Instead of using fib6_info_hold_safe() which ip6_rt_cache_alloc()
is already doing, this patch chooses to extend the rcu section
to keep "from" dereference-able after checking for NULL.
inet6_rtm_getroute():
1. NULL checking is also needed on rt->from for a similar reason.
Note that inet6_rtm_getroute() is using RTNL_FLAG_DOIT_UNLOCKED.
Fixes:
a68886a69180 ("net/ipv6: Make from in rt6_info rcu protected")
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Wei Wang <weiwan@google.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nicholas Mc Guire [Tue, 30 Apr 2019 03:12:57 +0000 (05:12 +0200)]
rds: ib: force endiannes annotation
While the endiannes is being handled correctly as indicated by the comment
above the offending line - sparse was unhappy with the missing annotation
as be64_to_cpu() expects a __be64 argument. To mitigate this annotation
all involved variables are changed to a consistent __le64 and the
conversion to uint64_t delayed to the call to rds_cong_map_updated().
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Wed, 1 May 2019 20:40:30 +0000 (13:40 -0700)]
Merge tag 'arc-5.1-final' of git://git./linux/kernel/git/vgupta/arc
Pull ARC fixes from Vineet Gupta:
"A few minor fixes for ARC.
- regression in memset if line size !64
- avoid panic if PAE and IOC"
* tag 'arc-5.1-final' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
ARC: memset: fix build with L1_CACHE_SHIFT != 6
ARC: [hsdk] Make it easier to add PAE40 region to DTB
ARC: PAE40: don't panic and instead turn off hw ioc
Alex Williamson [Mon, 22 Apr 2019 22:43:30 +0000 (16:43 -0600)]
PCI/portdrv: Use shared MSI/MSI-X vector for Bandwidth Management
The Interrupt Message Number in the PCIe Capabilities register (PCIe r4.0,
sec 7.5.3.2) indicates which MSI/MSI-X vector is shared by interrupts
related to the PCIe Capability, including Link Bandwidth Management and
Link Autonomous Bandwidth Interrupts (Link Control, 7.5.3.7), Command
Completed and Hot-Plug Interrupts (Slot Control, 7.5.3.10), and the PME
Interrupt (Root Control, 7.5.3.12).
pcie_message_numbers() checked whether we want to enable PME or Hot-Plug
interrupts but neglected to check for Link Bandwidth Management, so if we
only wanted the Bandwidth Management interrupts, it decided we didn't need
any vectors at all. Then pcie_port_enable_irq_vec() tried to reallocate
zero vectors, which failed, resulting in fallback to INTx.
On some systems, e.g., an X79-based workstation, that INTx seems broken or
not handled correctly, so we got spurious IRQ16 interrupts for Bandwidth
Management events.
Change pcie_message_numbers() so that if we want Link Bandwidth Management
interrupts, we use the shared MSI/MSI-X vector from the PCIe Capabilities
register.
Fixes:
e8303bb7a75c ("PCI/LINK: Report degraded links via link bandwidth notification")
Link: https://lore.kernel.org/lkml/155597243666.19387.1205950870601742062.stgit@gimli.home
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
[bhelgaas: changelog]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Linus Torvalds [Wed, 1 May 2019 20:03:39 +0000 (13:03 -0700)]
Merge tag 'acpi-5.1-rc8' of git://git./linux/kernel/git/rafael/linux-pm
Pull ACPI fix from Rafael Wysocki:
"Revert a recent ACPICA change that caused initialization to fail on
systems with Thunderbolt docking stations connected at the init time"
* tag 'acpi-5.1-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
Revert "ACPICA: Clear status of GPEs before enabling them"
Linus Torvalds [Wed, 1 May 2019 19:19:20 +0000 (12:19 -0700)]
gcc-9: don't warn about uninitialized btrfs extent_type variable
The 'extent_type' variable does seem to be reliably initialized, but
it's _very_ non-obvious, since there's a "goto next" case that jumps
over the normal initialization. That will then always trigger the
"start >= extent_end" test, which will end up never falling through to
the use of that variable.
But the code is certainly not obvious, and the compiler warning looks
reasonable. Make 'extent_type' an int, and initialize it to an invalid
negative value, which seems to be the common pattern in other places.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Hangbin Liu [Tue, 30 Apr 2019 02:46:10 +0000 (10:46 +0800)]
selftests: fib_rule_tests: print the result and return 1 if any tests failed
Fixes:
65b2b4939a64 ("selftests: net: initial fib rule tests")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Wed, 1 May 2019 18:20:53 +0000 (11:20 -0700)]
gcc-9: properly declare the {pv,hv}clock_page storage
The pvlock_page and hvclock_page variables are (as the name implies)
addresses to pages, created by the linker script.
But we declared them as just "extern u8" variables, which _works_, but
now that gcc does some more bounds checking, it causes warnings like
warning: array subscript 1 is outside array bounds of ‘u8[1]’
when we then access more than one byte from those variables.
Fix this by simply making the declaration of the variables match
reality, which makes the compiler happy too.
Signed-off-by: Linus Torvalds <torvalds@-linux-foundation.org>
Linus Torvalds [Wed, 1 May 2019 18:07:40 +0000 (11:07 -0700)]
gcc-9: don't warn about uninitialized variable
I'm not sure what made gcc warn about this code now. The 'ret' variable
does end up initialized in all cases, but it's definitely not obvious,
so the compiler is quite reasonable to warn about this.
So just add initialization to make it all much more obvious both to
compilers and to humans.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Wed, 1 May 2019 18:05:41 +0000 (11:05 -0700)]
gcc-9: silence 'address-of-packed-member' warning
We already did this for clang, but now gcc has that warning too. Yes,
yes, the address may be unaligned. And that's kind of the point.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Shmulik Ladkani [Mon, 29 Apr 2019 13:39:30 +0000 (16:39 +0300)]
ipv4: ip_do_fragment: Preserve skb_iif during fragmentation
Previously, during fragmentation after forwarding, skb->skb_iif isn't
preserved, i.e. 'ip_copy_metadata' does not copy skb_iif from given
'from' skb.
As a result, ip_do_fragment's creates fragments with zero skb_iif,
leading to inconsistent behavior.
Assume for example an eBPF program attached at tc egress (post
forwarding) that examines __sk_buff->ingress_ifindex:
- the correct iif is observed if forwarding path does not involve
fragmentation/refragmentation
- a bogus iif is observed if forwarding path involves
fragmentation/refragmentatiom
Fix, by preserving skb_iif during 'ip_copy_metadata'.
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mark Rutland [Wed, 1 May 2019 15:59:16 +0000 (16:59 +0100)]
io_uring: avoid page allocation warnings
In io_sqe_buffer_register() we allocate a number of arrays based on the
iov_len from the user-provided iov. While we limit iov_len to SZ_1G,
we can still attempt to allocate arrays exceeding MAX_ORDER.
On a 64-bit system with 4KiB pages, for an iov where iov_base = 0x10 and
iov_len = SZ_1G, we'll calculate that nr_pages = 262145. When we try to
allocate a corresponding array of (16-byte) bio_vecs, requiring 4194320
bytes, which is greater than 4MiB. This results in SLUB warning that
we're trying to allocate greater than MAX_ORDER, and failing the
allocation.
Avoid this by using kvmalloc() for allocations dependent on the
user-provided iov_len. At the same time, fix a leak of imu->bvec when
registration fails.
Full splat from before this patch:
WARNING: CPU: 1 PID: 2314 at mm/page_alloc.c:4595 __alloc_pages_nodemask+0x7ac/0x2938 mm/page_alloc.c:4595
Kernel panic - not syncing: panic_on_warn set ...
CPU: 1 PID: 2314 Comm: syz-executor326 Not tainted 5.1.0-rc7-dirty #4
Hardware name: linux,dummy-virt (DT)
Call trace:
dump_backtrace+0x0/0x2f0 include/linux/compiler.h:193
show_stack+0x20/0x30 arch/arm64/kernel/traps.c:158
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x110/0x190 lib/dump_stack.c:113
panic+0x384/0x68c kernel/panic.c:214
__warn+0x2bc/0x2c0 kernel/panic.c:571
report_bug+0x228/0x2d8 lib/bug.c:186
bug_handler+0xa0/0x1a0 arch/arm64/kernel/traps.c:956
call_break_hook arch/arm64/kernel/debug-monitors.c:301 [inline]
brk_handler+0x1d4/0x388 arch/arm64/kernel/debug-monitors.c:316
do_debug_exception+0x1a0/0x468 arch/arm64/mm/fault.c:831
el1_dbg+0x18/0x8c
__alloc_pages_nodemask+0x7ac/0x2938 mm/page_alloc.c:4595
alloc_pages_current+0x164/0x278 mm/mempolicy.c:2132
alloc_pages include/linux/gfp.h:509 [inline]
kmalloc_order+0x20/0x50 mm/slab_common.c:1231
kmalloc_order_trace+0x30/0x2b0 mm/slab_common.c:1243
kmalloc_large include/linux/slab.h:480 [inline]
__kmalloc+0x3dc/0x4f0 mm/slub.c:3791
kmalloc_array include/linux/slab.h:670 [inline]
io_sqe_buffer_register fs/io_uring.c:2472 [inline]
__io_uring_register fs/io_uring.c:2962 [inline]
__do_sys_io_uring_register fs/io_uring.c:3008 [inline]
__se_sys_io_uring_register fs/io_uring.c:2990 [inline]
__arm64_sys_io_uring_register+0x9e0/0x1bc8 fs/io_uring.c:2990
__invoke_syscall arch/arm64/kernel/syscall.c:35 [inline]
invoke_syscall arch/arm64/kernel/syscall.c:47 [inline]
el0_svc_common.constprop.0+0x148/0x2e0 arch/arm64/kernel/syscall.c:83
el0_svc_handler+0xdc/0x100 arch/arm64/kernel/syscall.c:129
el0_svc+0x8/0xc arch/arm64/kernel/entry.S:948
SMP: stopping secondary CPUs
Dumping ftrace buffer:
(ftrace buffer empty)
Kernel Offset: disabled
CPU features: 0x002,
23000438
Memory Limit: none
Rebooting in 1 seconds..
Fixes:
edafccee56ff3167 ("io_uring: add support for pre-mapped user IO buffers")
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: linux-fsdevel@vger.kernel.org
Cc: linux-block@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Jakub Kicinski [Mon, 29 Apr 2019 19:19:12 +0000 (12:19 -0700)]
net/tls: avoid NULL pointer deref on nskb->sk in fallback
update_chksum() accesses nskb->sk before it has been set
by complete_skb(), move the init up.
Fixes:
e8f69799810c ("net/tls: Add generic NIC offload infrastructure")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Mon, 29 Apr 2019 17:30:09 +0000 (10:30 -0700)]
selftests: fib_rule_tests: Fix icmp proto with ipv6
A recent commit returns an error if icmp is used as the ip-proto for
IPv6 fib rules. Update fib_rule_tests to send ipv6-icmp instead of icmp.
Fixes:
5e1a99eae8499 ("ipv4: Add ICMPv6 support when parse route ipproto")
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Willem de Bruijn [Mon, 29 Apr 2019 15:53:18 +0000 (11:53 -0400)]
packet: validate msg_namelen in send directly
Packet sockets in datagram mode take a destination address. Verify its
length before passing to dev_hard_header.
Prior to 2.6.14-rc3, the send code ignored sll_halen. This is
established behavior. Directly compare msg_namelen to dev->addr_len.
Change v1->v2: initialize addr in all paths
Fixes:
6b8d95f1795c4 ("packet: validate address length if non-zero")
Suggested-by: David Laight <David.Laight@aculab.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Willem de Bruijn [Mon, 29 Apr 2019 15:46:55 +0000 (11:46 -0400)]
packet: in recvmsg msg_name return at least sizeof sockaddr_ll
Packet send checks that msg_name is at least sizeof sockaddr_ll.
Packet recv must return at least this length, so that its output
can be passed unmodified to packet send.
This ceased to be true since adding support for lladdr longer than
sll_addr. Since, the return value uses true address length.
Always return at least sizeof sockaddr_ll, even if address length
is shorter. Zero the padding bytes.
Change v1->v2: do not overwrite zeroed padding again. use copy_len.
Fixes:
0fb375fb9b93 ("[AF_PACKET]: Allow for > 8 byte hardware addresses.")
Suggested-by: David Laight <David.Laight@aculab.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ming Lei [Fri, 26 Apr 2019 10:45:21 +0000 (18:45 +0800)]
iov_iter: fix iov_iter_type
Commit
875f1d0769cd ("iov_iter: add ITER_BVEC_FLAG_NO_REF flag")
introduces one extra flag of ITER_BVEC_FLAG_NO_REF, and this flag
is stored into iter->type.
However, iov_iter_type() doesn't consider the new added flag, fix
it by masking this flag in iov_iter_type().
Fixes:
875f1d0769cd ("iov_iter: add ITER_BVEC_FLAG_NO_REF flag")
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Ming Lei [Fri, 26 Apr 2019 10:45:20 +0000 (18:45 +0800)]
block: fix handling for BIO_NO_PAGE_REF
Commit
399254aaf489211 ("block: add BIO_NO_PAGE_REF flag") introduces
BIO_NO_PAGE_REF, and once this flag is set for one bio, all pages
in the bio won't be get/put during IO.
However, if one bio is submitted via __blkdev_direct_IO_simple(),
even though BIO_NO_PAGE_REF is set, pages still may be put.
Fixes this issue by avoiding to put pages if BIO_NO_PAGE_REF is
set.
Fixes:
399254aaf489211 ("block: add BIO_NO_PAGE_REF flag")
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Jens Axboe [Tue, 30 Apr 2019 20:44:05 +0000 (14:44 -0600)]
io_uring: drop req submit reference always in async punt
If we don't end up actually calling submit in io_sq_wq_submit_work(),
we still need to drop the submit reference to the request. If we
don't, then we can leak the request. This can happen if we race
with ring shutdown while flushing the workqueue for requests that
require use of the mm_struct.
Fixes:
e65ef56db494 ("io_uring: use regular request ref counts")
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Mark Rutland [Tue, 30 Apr 2019 16:30:21 +0000 (17:30 +0100)]
io_uring: free allocated io_memory once
If io_allocate_scq_urings() fails to allocate an sq_* region, it will
call io_mem_free() for any previously allocated regions, but leave
dangling pointers to these regions in the ctx. Any regions which have
not yet been allocated are left NULL. Note that when returning
-EOVERFLOW, the previously allocated sq_ring is not freed, which appears
to be an unintentional leak.
When io_allocate_scq_urings() fails, io_uring_create() will call
io_ring_ctx_wait_and_kill(), which calls io_mem_free() on all the sq_*
regions, assuming the pointers are valid and not NULL.
This can result in pages being freed multiple times, which has been
observed to corrupt the page state, leading to subsequent fun. This can
also result in virt_to_page() on NULL, resulting in the use of bogus
page addresses, and yet more subsequent fun. The latter can be detected
with CONFIG_DEBUG_VIRTUAL on arm64.
Adding a cleanup path to io_allocate_scq_urings() complicates the logic,
so let's leave it to io_ring_ctx_free() to consistently free these
pointers, and simplify the io_allocate_scq_urings() error paths.
Full splats from before this patch below. Note that the pointer logged
by the DEBUG_VIRTUAL "non-linear address" warning has been hashed, and
is actually NULL.
[ 26.098129] page:
ffff80000e949a00 count:0 mapcount:-128 mapping:
0000000000000000 index:0x0
[ 26.102976] flags: 0x63fffc000000()
[ 26.104373] raw:
000063fffc000000 ffff80000e86c188 ffff80000ea3df08 0000000000000000
[ 26.108917] raw:
0000000000000000 0000000000000001 00000000ffffff7f 0000000000000000
[ 26.137235] page dumped because: VM_BUG_ON_PAGE(page_ref_count(page) == 0)
[ 26.143960] ------------[ cut here ]------------
[ 26.146020] kernel BUG at include/linux/mm.h:547!
[ 26.147586] Internal error: Oops - BUG: 0 [#1] PREEMPT SMP
[ 26.149163] Modules linked in:
[ 26.150287] Process syz-executor.21 (pid: 20204, stack limit = 0x000000000e9cefeb)
[ 26.153307] CPU: 2 PID: 20204 Comm: syz-executor.21 Not tainted 5.1.0-rc7-00004-g7d30b2ea43d6 #18
[ 26.156566] Hardware name: linux,dummy-virt (DT)
[ 26.158089] pstate:
40400005 (nZcv daif +PAN -UAO)
[ 26.159869] pc : io_mem_free+0x9c/0xa8
[ 26.161436] lr : io_mem_free+0x9c/0xa8
[ 26.162720] sp :
ffff000013003d60
[ 26.164048] x29:
ffff000013003d60 x28:
ffff800025048040
[ 26.165804] x27:
0000000000000000 x26:
ffff800025048040
[ 26.167352] x25:
00000000000000c0 x24:
ffff0000112c2820
[ 26.169682] x23:
0000000000000000 x22:
0000000020000080
[ 26.171899] x21:
ffff80002143b418 x20:
ffff80002143b400
[ 26.174236] x19:
ffff80002143b280 x18:
0000000000000000
[ 26.176607] x17:
0000000000000000 x16:
0000000000000000
[ 26.178997] x15:
0000000000000000 x14:
0000000000000000
[ 26.181508] x13:
00009178a5e077b2 x12:
0000000000000001
[ 26.183863] x11:
0000000000000000 x10:
0000000000000980
[ 26.186437] x9 :
ffff000013003a80 x8 :
ffff800025048a20
[ 26.189006] x7 :
ffff8000250481c0 x6 :
ffff80002ffe9118
[ 26.191359] x5 :
ffff80002ffe9118 x4 :
0000000000000000
[ 26.193863] x3 :
ffff80002ffefe98 x2 :
44c06ddd107d1f00
[ 26.196642] x1 :
0000000000000000 x0 :
000000000000003e
[ 26.198892] Call trace:
[ 26.199893] io_mem_free+0x9c/0xa8
[ 26.201155] io_ring_ctx_wait_and_kill+0xec/0x180
[ 26.202688] io_uring_setup+0x6c4/0x6f0
[ 26.204091] __arm64_sys_io_uring_setup+0x18/0x20
[ 26.205576] el0_svc_common.constprop.0+0x7c/0xe8
[ 26.207186] el0_svc_handler+0x28/0x78
[ 26.208389] el0_svc+0x8/0xc
[ 26.209408] Code:
aa0203e0 d0006861 9133a021 97fcdc3c (
d4210000)
[ 26.211995] ---[ end trace
bdb81cd43a21e50d ]---
[ 81.770626] ------------[ cut here ]------------
[ 81.825015] virt_to_phys used for non-linear address:
000000000d42f2c7 ( (null))
[ 81.827860] WARNING: CPU: 1 PID: 30171 at arch/arm64/mm/physaddr.c:15 __virt_to_phys+0x48/0x68
[ 81.831202] Modules linked in:
[ 81.832212] CPU: 1 PID: 30171 Comm: syz-executor.20 Not tainted 5.1.0-rc7-00004-g7d30b2ea43d6 #19
[ 81.835616] Hardware name: linux,dummy-virt (DT)
[ 81.836863] pstate:
60400005 (nZCv daif +PAN -UAO)
[ 81.838727] pc : __virt_to_phys+0x48/0x68
[ 81.840572] lr : __virt_to_phys+0x48/0x68
[ 81.842264] sp :
ffff80002cf67c70
[ 81.843858] x29:
ffff80002cf67c70 x28:
ffff800014358e18
[ 81.846463] x27:
0000000000000000 x26:
0000000020000080
[ 81.849148] x25:
0000000000000000 x24:
ffff80001bb01f40
[ 81.851986] x23:
ffff200011db06c8 x22:
ffff2000127e3c60
[ 81.854351] x21:
ffff800014358cc0 x20:
ffff800014358d98
[ 81.856711] x19:
0000000000000000 x18:
0000000000000000
[ 81.859132] x17:
0000000000000000 x16:
0000000000000000
[ 81.861586] x15:
0000000000000000 x14:
0000000000000000
[ 81.863905] x13:
0000000000000000 x12:
ffff1000037603e9
[ 81.866226] x11:
1ffff000037603e8 x10:
0000000000000980
[ 81.868776] x9 :
ffff80002cf67840 x8 :
ffff80001bb02920
[ 81.873272] x7 :
ffff1000037603e9 x6 :
ffff80001bb01f47
[ 81.875266] x5 :
ffff1000037603e9 x4 :
dfff200000000000
[ 81.876875] x3 :
ffff200010087528 x2 :
ffff1000059ecf58
[ 81.878751] x1 :
44c06ddd107d1f00 x0 :
0000000000000000
[ 81.880453] Call trace:
[ 81.881164] __virt_to_phys+0x48/0x68
[ 81.882919] io_mem_free+0x18/0x110
[ 81.886585] io_ring_ctx_wait_and_kill+0x13c/0x1f0
[ 81.891212] io_uring_setup+0xa60/0xad0
[ 81.892881] __arm64_sys_io_uring_setup+0x2c/0x38
[ 81.894398] el0_svc_common.constprop.0+0xac/0x150
[ 81.896306] el0_svc_handler+0x34/0x88
[ 81.897744] el0_svc+0x8/0xc
[ 81.898715] ---[ end trace
b4a703802243cbba ]---
Fixes:
2b188cc1bb857a9d ("Add io_uring IO interface")
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: linux-block@vger.kernel.org
Cc: linux-fsdevel@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Mark Rutland [Tue, 30 Apr 2019 12:34:51 +0000 (13:34 +0100)]
io_uring: fix SQPOLL cpu validation
In io_sq_offload_start(), we call cpu_possible() on an unbounded cpu
value from userspace. On v5.1-rc7 on arm64 with
CONFIG_DEBUG_PER_CPU_MAPS, this results in a splat:
WARNING: CPU: 1 PID: 27601 at include/linux/cpumask.h:121 cpu_max_bits_warn include/linux/cpumask.h:121 [inline]
There was an attempt to fix this in commit:
917257daa0fea7a0 ("io_uring: only test SQPOLL cpu after we've verified it")
... by adding a check after the cpu value had been limited to NR_CPU_IDS
using array_index_nospec(). However, this left an unbound check at the
start of the function, for which the warning still fires.
Let's fix this correctly by checking that the cpu value is bound by
nr_cpu_ids before passing it to cpu_possible(). Note that only
nr_cpu_ids of a cpumask are guaranteed to exist at runtime, and
nr_cpu_ids can be significantly smaller than NR_CPUs. For example, an
arm64 defconfig has NR_CPUS=256, while my test VM has 4 vCPUs.
Following the intent from the commit message for
917257daa0fea7a0, the
check is moved under the SQ_AFF branch, which is the only branch where
the cpu values is consumed. The check is performed before bounding the
value with array_index_nospec() so that we don't silently accept bogus
cpu values from userspace, where array_index_nospec() would force these
values to 0.
I suspect we can remove the array_index_nospec() call entirely, but I've
conservatively left that in place, updated to use nr_cpu_ids to match
the prior check.
Tested on arm64 with the Syzkaller reproducer:
https://syzkaller.appspot.com/bug?extid=
cd714a07c6de2bc34293
https://syzkaller.appspot.com/x/repro.syz?x=
15d8b397200000
Full splat from before this patch:
WARNING: CPU: 1 PID: 27601 at include/linux/cpumask.h:121 cpu_max_bits_warn include/linux/cpumask.h:121 [inline]
WARNING: CPU: 1 PID: 27601 at include/linux/cpumask.h:121 cpumask_check include/linux/cpumask.h:128 [inline]
WARNING: CPU: 1 PID: 27601 at include/linux/cpumask.h:121 cpumask_test_cpu include/linux/cpumask.h:344 [inline]
WARNING: CPU: 1 PID: 27601 at include/linux/cpumask.h:121 io_sq_offload_start fs/io_uring.c:2244 [inline]
WARNING: CPU: 1 PID: 27601 at include/linux/cpumask.h:121 io_uring_create fs/io_uring.c:2864 [inline]
WARNING: CPU: 1 PID: 27601 at include/linux/cpumask.h:121 io_uring_setup+0x1108/0x15a0 fs/io_uring.c:2916
Kernel panic - not syncing: panic_on_warn set ...
CPU: 1 PID: 27601 Comm: syz-executor.0 Not tainted 5.1.0-rc7 #3
Hardware name: linux,dummy-virt (DT)
Call trace:
dump_backtrace+0x0/0x2f0 include/linux/compiler.h:193
show_stack+0x20/0x30 arch/arm64/kernel/traps.c:158
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x110/0x190 lib/dump_stack.c:113
panic+0x384/0x68c kernel/panic.c:214
__warn+0x2bc/0x2c0 kernel/panic.c:571
report_bug+0x228/0x2d8 lib/bug.c:186
bug_handler+0xa0/0x1a0 arch/arm64/kernel/traps.c:956
call_break_hook arch/arm64/kernel/debug-monitors.c:301 [inline]
brk_handler+0x1d4/0x388 arch/arm64/kernel/debug-monitors.c:316
do_debug_exception+0x1a0/0x468 arch/arm64/mm/fault.c:831
el1_dbg+0x18/0x8c
cpu_max_bits_warn include/linux/cpumask.h:121 [inline]
cpumask_check include/linux/cpumask.h:128 [inline]
cpumask_test_cpu include/linux/cpumask.h:344 [inline]
io_sq_offload_start fs/io_uring.c:2244 [inline]
io_uring_create fs/io_uring.c:2864 [inline]
io_uring_setup+0x1108/0x15a0 fs/io_uring.c:2916
__do_sys_io_uring_setup fs/io_uring.c:2929 [inline]
__se_sys_io_uring_setup fs/io_uring.c:2926 [inline]
__arm64_sys_io_uring_setup+0x50/0x70 fs/io_uring.c:2926
__invoke_syscall arch/arm64/kernel/syscall.c:35 [inline]
invoke_syscall arch/arm64/kernel/syscall.c:47 [inline]
el0_svc_common.constprop.0+0x148/0x2e0 arch/arm64/kernel/syscall.c:83
el0_svc_handler+0xdc/0x100 arch/arm64/kernel/syscall.c:129
el0_svc+0x8/0xc arch/arm64/kernel/entry.S:948
SMP: stopping secondary CPUs
Dumping ftrace buffer:
(ftrace buffer empty)
Kernel Offset: disabled
CPU features: 0x002,
23000438
Memory Limit: none
Rebooting in 1 seconds..
Fixes:
917257daa0fea7a0 ("io_uring: only test SQPOLL cpu after we've verified it")
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: linux-block@vger.kernel.org
Cc: linux-fsdevel@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Simplied the logic
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Xin Long [Mon, 29 Apr 2019 06:16:19 +0000 (14:16 +0800)]
sctp: avoid running the sctp state machine recursively
Ying triggered a call trace when doing an asconf testing:
BUG: scheduling while atomic: swapper/12/0/0x10000100
Call Trace:
<IRQ> [<
ffffffffa4375904>] dump_stack+0x19/0x1b
[<
ffffffffa436fcaf>] __schedule_bug+0x64/0x72
[<
ffffffffa437b93a>] __schedule+0x9ba/0xa00
[<
ffffffffa3cd5326>] __cond_resched+0x26/0x30
[<
ffffffffa437bc4a>] _cond_resched+0x3a/0x50
[<
ffffffffa3e22be8>] kmem_cache_alloc_node+0x38/0x200
[<
ffffffffa423512d>] __alloc_skb+0x5d/0x2d0
[<
ffffffffc0995320>] sctp_packet_transmit+0x610/0xa20 [sctp]
[<
ffffffffc098510e>] sctp_outq_flush+0x2ce/0xc00 [sctp]
[<
ffffffffc098646c>] sctp_outq_uncork+0x1c/0x20 [sctp]
[<
ffffffffc0977338>] sctp_cmd_interpreter.isra.22+0xc8/0x1460 [sctp]
[<
ffffffffc0976ad1>] sctp_do_sm+0xe1/0x350 [sctp]
[<
ffffffffc099443d>] sctp_primitive_ASCONF+0x3d/0x50 [sctp]
[<
ffffffffc0977384>] sctp_cmd_interpreter.isra.22+0x114/0x1460 [sctp]
[<
ffffffffc0976ad1>] sctp_do_sm+0xe1/0x350 [sctp]
[<
ffffffffc097b3a4>] sctp_assoc_bh_rcv+0xf4/0x1b0 [sctp]
[<
ffffffffc09840f1>] sctp_inq_push+0x51/0x70 [sctp]
[<
ffffffffc099732b>] sctp_rcv+0xa8b/0xbd0 [sctp]
As it shows, the first sctp_do_sm() running under atomic context (NET_RX
softirq) invoked sctp_primitive_ASCONF() that uses GFP_KERNEL flag later,
and this flag is supposed to be used in non-atomic context only. Besides,
sctp_do_sm() was called recursively, which is not expected.
Vlad tried to fix this recursive call in Commit
c0786693404c ("sctp: Fix
oops when sending queued ASCONF chunks") by introducing a new command
SCTP_CMD_SEND_NEXT_ASCONF. But it didn't work as this command is still
used in the first sctp_do_sm() call, and sctp_primitive_ASCONF() will
be called in this command again.
To avoid calling sctp_do_sm() recursively, we send the next queued ASCONF
not by sctp_primitive_ASCONF(), but by sctp_sf_do_prm_asconf() in the 1st
sctp_do_sm() directly.
Reported-by: Ying Xu <yinxu@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jan Kiszka [Mon, 29 Apr 2019 05:51:44 +0000 (07:51 +0200)]
stmmac: pci: Fix typo in IOT2000 comment
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Randy Dunlap [Mon, 29 Apr 2019 01:10:39 +0000 (18:10 -0700)]
Documentation: fix netdev-FAQ.rst markup warning
Fix ReST underline warning:
./Documentation/networking/netdev-FAQ.rst:135: WARNING: Title underline too short.
Q: I made changes to only a few patches in a patch series should I resend only those changed?
--------------------------------------------------------------------------------------------
Fixes:
ffa91253739c ("Documentation: networking: Update netdev-FAQ regarding patches")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jens Axboe [Tue, 30 Apr 2019 16:16:07 +0000 (10:16 -0600)]
io_uring: have submission side sqe errors post a cqe
Currently we only post a cqe if we get an error OUTSIDE of submission.
For submission, we return the error directly through io_uring_enter().
This is a bit awkward for applications, and it makes more sense to
always post a cqe with an error, if the error happens on behalf of an
sqe.
This changes submission behavior a bit. io_uring_enter() returns -ERROR
for an error, and > 0 for number of sqes submitted. Before this change,
if you wanted to submit 8 entries and had an error on the 5th entry,
io_uring_enter() would return 4 (for number of entries successfully
submitted) and rewind the sqring. The application would then have to
peek at the sqring and figure out what was wrong with the head sqe, and
then skip it itself. With this change, we'll return 5 since we did
consume 5 sqes, and the last sqe (with the error) will result in a cqe
being posted with the error.
This makes the logic easier to handle in the application, and it cleans
up the submission part.
Suggested-by: Stefan Bühler <source@stbuehler.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Eric Dumazet [Sun, 28 Apr 2019 19:22:25 +0000 (12:22 -0700)]
ipv6: fix races in ip6_dst_destroy()
We had many syzbot reports that seem to be caused by use-after-free
of struct fib6_info.
ip6_dst_destroy(), fib6_drop_pcpu_from() and rt6_remove_exception()
are writers vs rt->from, and use non consistent synchronization among
themselves.
Switching to xchg() will solve the issues with no possible
lockdep issues.
BUG: KASAN: user-memory-access in atomic_dec_and_test include/asm-generic/atomic-instrumented.h:747 [inline]
BUG: KASAN: user-memory-access in fib6_info_release include/net/ip6_fib.h:294 [inline]
BUG: KASAN: user-memory-access in fib6_info_release include/net/ip6_fib.h:292 [inline]
BUG: KASAN: user-memory-access in fib6_drop_pcpu_from net/ipv6/ip6_fib.c:927 [inline]
BUG: KASAN: user-memory-access in fib6_purge_rt+0x4f6/0x670 net/ipv6/ip6_fib.c:960
Write of size 4 at addr
0000000000ffffb4 by task syz-executor.1/7649
CPU: 0 PID: 7649 Comm: syz-executor.1 Not tainted 5.1.0-rc6+ #183
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x172/0x1f0 lib/dump_stack.c:113
kasan_report.cold+0x5/0x40 mm/kasan/report.c:321
check_memory_region_inline mm/kasan/generic.c:185 [inline]
check_memory_region+0x123/0x190 mm/kasan/generic.c:191
kasan_check_write+0x14/0x20 mm/kasan/common.c:108
atomic_dec_and_test include/asm-generic/atomic-instrumented.h:747 [inline]
fib6_info_release include/net/ip6_fib.h:294 [inline]
fib6_info_release include/net/ip6_fib.h:292 [inline]
fib6_drop_pcpu_from net/ipv6/ip6_fib.c:927 [inline]
fib6_purge_rt+0x4f6/0x670 net/ipv6/ip6_fib.c:960
fib6_del_route net/ipv6/ip6_fib.c:1813 [inline]
fib6_del+0xac2/0x10a0 net/ipv6/ip6_fib.c:1844
fib6_clean_node+0x3a8/0x590 net/ipv6/ip6_fib.c:2006
fib6_walk_continue+0x495/0x900 net/ipv6/ip6_fib.c:1928
fib6_walk+0x9d/0x100 net/ipv6/ip6_fib.c:1976
fib6_clean_tree+0xe0/0x120 net/ipv6/ip6_fib.c:2055
__fib6_clean_all+0x118/0x2a0 net/ipv6/ip6_fib.c:2071
fib6_clean_all+0x2b/0x40 net/ipv6/ip6_fib.c:2082
rt6_sync_down_dev+0x134/0x150 net/ipv6/route.c:4057
rt6_disable_ip+0x27/0x5f0 net/ipv6/route.c:4062
addrconf_ifdown+0xa2/0x1220 net/ipv6/addrconf.c:3705
addrconf_notify+0x19a/0x2260 net/ipv6/addrconf.c:3630
notifier_call_chain+0xc7/0x240 kernel/notifier.c:93
__raw_notifier_call_chain kernel/notifier.c:394 [inline]
raw_notifier_call_chain+0x2e/0x40 kernel/notifier.c:401
call_netdevice_notifiers_info+0x3f/0x90 net/core/dev.c:1753
call_netdevice_notifiers_extack net/core/dev.c:1765 [inline]
call_netdevice_notifiers net/core/dev.c:1779 [inline]
dev_close_many+0x33f/0x6f0 net/core/dev.c:1522
rollback_registered_many+0x43b/0xfd0 net/core/dev.c:8177
rollback_registered+0x109/0x1d0 net/core/dev.c:8242
unregister_netdevice_queue net/core/dev.c:9289 [inline]
unregister_netdevice_queue+0x1ee/0x2c0 net/core/dev.c:9282
unregister_netdevice include/linux/netdevice.h:2658 [inline]
__tun_detach+0xd5b/0x1000 drivers/net/tun.c:727
tun_detach drivers/net/tun.c:744 [inline]
tun_chr_close+0xe0/0x180 drivers/net/tun.c:3443
__fput+0x2e5/0x8d0 fs/file_table.c:278
____fput+0x16/0x20 fs/file_table.c:309
task_work_run+0x14a/0x1c0 kernel/task_work.c:113
exit_task_work include/linux/task_work.h:22 [inline]
do_exit+0x90a/0x2fa0 kernel/exit.c:876
do_group_exit+0x135/0x370 kernel/exit.c:980
__do_sys_exit_group kernel/exit.c:991 [inline]
__se_sys_exit_group kernel/exit.c:989 [inline]
__x64_sys_exit_group+0x44/0x50 kernel/exit.c:989
do_syscall_64+0x103/0x610 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x49/0xbe
RIP: 0033:0x458da9
Code: ad b8 fb ff c3 66 2e 0f 1f 84 00 00 00 00 00 66 90 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 0f 83 7b b8 fb ff c3 66 2e 0f 1f 84 00 00 00 00
RSP: 002b:
00007ffeafc2a6a8 EFLAGS:
00000246 ORIG_RAX:
00000000000000e7
RAX:
ffffffffffffffda RBX:
000000000000001c RCX:
0000000000458da9
RDX:
0000000000412a80 RSI:
0000000000a54ef0 RDI:
0000000000000043
RBP:
00000000004be552 R08:
000000000000000c R09:
000000000004c0d1
R10:
0000000002341940 R11:
0000000000000246 R12:
00000000ffffffff
R13:
00007ffeafc2a7f0 R14:
000000000004c065 R15:
00007ffeafc2a800
Fixes:
a68886a69180 ("net/ipv6: Make from in rt6_info rcu protected")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Cc: David Ahern <dsahern@gmail.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Wei Wang <weiwan@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
projects / platform / kernel / linux-starfive.git / log