Stefan Brüns [Sun, 6 Nov 2016 00:32:15 +0000 (01:32 +0100)]
fs-test.sh: Update expected results
After the latest changes, ext4 no longer has any fails.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Stefan Brüns [Sun, 6 Nov 2016 17:33:57 +0000 (18:33 +0100)]
ext4: Allow reading files with non-zero offset, clamp read len
Support was already implemented, but not hooked up. This fixes several
fails in the test cases.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Stefan Brüns [Sat, 5 Nov 2016 21:17:14 +0000 (22:17 +0100)]
ext4: Fix handling of sparse files
A sparse file may have regions not mapped by any extents, at the start
or at the end of the file, or anywhere between, thus not finding a
matching extent region is never an error.
Found by python filesystem tests.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Stefan Brüns [Sat, 5 Nov 2016 16:45:32 +0000 (17:45 +0100)]
test/py: expose config and log as session scoped fixture
If a test uses a fixture which is expensive to setup, the fixture can
possibly created with session or module scope. As u_boot_console has
function scope, it can not be used in this case.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Phil Edworthy [Thu, 3 Nov 2016 11:05:12 +0000 (11:05 +0000)]
gpio: dwapb: Add support for port B
The IP supports two ports, A and B, each providing up to 32 gpios.
The driver already creates a 2nd gpio bank by reading the 2nd node
from DT, so this is quite a simple change to support the 2nd bank.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Acked-by: Marek Vasut <marex@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Semen Protsenko [Mon, 31 Oct 2016 17:53:46 +0000 (19:53 +0200)]
arm: dra7xx: Unify Android partition table
Make Android partition table the same as for AM57x EVM.
1. Make "bootloader" partition start from 0x300 sectors offset, so
DRA7 is bootable in Android mode (see
CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR option).
2. Increase "bootloader" partition size, because size of u-boot.img is
about 632 KiB (when building DT defconfig, with FIT image enabled).
3. Specify "reserved" partition explicitly, rather than specifying
"efs" partition start. Reserved area will be used to store U-Boot
environment on eMMC. It's convenient to have it exposed explicitly
so we can read/write U-Boot environment.
4. Keep all Android partitions locations intact, by reducing
"reserved" partition size. CONFIG_ENV_SIZE is considered.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Semen Protsenko [Mon, 31 Oct 2016 17:53:42 +0000 (19:53 +0200)]
arm: am57xx: Enable 8-bit eMMC access
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Semen Protsenko [Mon, 31 Oct 2016 17:53:38 +0000 (19:53 +0200)]
arm: am57xx: Define Android partition table
"fastboot oem format" command reuses "gpt write" command, which in turn
requires correct partitions defined in $partitions variable. This patch
adds such definition of Android partitions for DRA7XX EVM board.
By default $partitions variable contains Linux partition table. In order
to prepare Android environment one can run next commands from U-Boot
shell:
=> env set partitions $partitions_android
=> env save
After those operations one can go to fastboot mode and perform
"fastboot oem format" to create Android partition table.
While at it, enable CONFIG_RANDOM_UUID to spare user from providing
UUIDs for each partition manually.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Guillaume GARDET [Tue, 25 Oct 2016 16:50:32 +0000 (18:50 +0200)]
omap3_beagle: use config_distro_bootcmd
Add support for distro_bootcmd on MMC and fall back to prior
behavior if distro_bootcmd fails.
Tested on Beagleboad xM to boot GRUB2 (and then Linux kernel) in EFI mode
from MMC.
Signed-off-by: Guillaume GARDET <guillaume.gardet@free.fr>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Semen Protsenko [Mon, 24 Oct 2016 15:41:13 +0000 (18:41 +0300)]
configs: am57xx: Enable fastboot
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Semen Protsenko [Mon, 24 Oct 2016 15:41:12 +0000 (18:41 +0300)]
configs: am57xx: Enable download gadget
Enable USB download gadget (needed for fastboot support) and all
dependencies.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Semen Protsenko [Mon, 24 Oct 2016 15:41:11 +0000 (18:41 +0300)]
ti_omap5_common: Respect USB controller number in fastboot
On "fastboot reboot-bootloader" we check "dofastboot" variable and do
"fastboot 0" command in U-Boot if it's 1. But there are boards which have
USB controller number other than 0, so it should be respected when
performing "fastboot" command.
This patch reuses CONFIG_FASTBOOT_USB_DEV option toprovide correct USB
controller number to "fastboot" command.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Semen Protsenko [Mon, 24 Oct 2016 15:41:10 +0000 (18:41 +0300)]
fastboot: Add CONFIG_FASTBOOT_USB_DEV option
Some boards (like AM57x EVM) has USB OTG controller other than 0. So in
order to use correct controller number in compiled environment we should
define CONFIG_FASTBOOT_USB_DEV option.
For example, when doing "fastboot reboot-bootloader" we want to enter
fastboot mode automatically. But to do so we need to provide controller
number to "fastboot" command. If this procedure is defined in some config
which is common to bunch of boards, and boards have different USB
controller numbers, we can't just hardcode "fastboot 0" in the
environment. We need to use configurable option, which this patch adds.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Lokesh Vutla [Fri, 14 Oct 2016 05:05:25 +0000 (10:35 +0530)]
board: ti: amx3xx: Remove multiple EEPROM reads
Detect the board very early and avoid reading eeprom multiple times.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Lokesh Vutla [Fri, 14 Oct 2016 05:05:24 +0000 (10:35 +0530)]
ARM: AMx3xx: Centralize early clock initialization
This is similar to Commit
93e6253d11030 ("ARM: OMAP4/5: Centralize
early clock initialization") that was done for OMAP4+, reflecting the same
for AM33xx and AM43xx SoCs to centralize clock initialization.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Add setup_early_clocks that calls setup_clocks_for_console for
ti81xx]
Signed-off-by: Tom Rini <trini@konsulko.com>
Shengzhou Liu [Fri, 11 Nov 2016 10:11:05 +0000 (18:11 +0800)]
armv8/fsl-layerscape: Update CONFIG_LS2080A to CONFIG_FSL_LSCH3
Update CONFIG_LS2080A to CONFIG_FSL_LSCH3 to make those workaround
implementing of erratum reusable for more SoCs.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Yuan Yao [Wed, 9 Nov 2016 03:50:46 +0000 (11:50 +0800)]
armv8: fsl-layerscape: Add README for deploying QSPI image
Signed-off-by: Yuan Yao <yao.yuan@nxp.com>
[YS: Reviese commit subject]
Reviewed-by: York Sun <york.sun@nxp.com>
Yuan Yao [Wed, 9 Nov 2016 03:19:54 +0000 (11:19 +0800)]
arm: ls1021a: improve the core frequency to 1.2GHZ
Change core clock to 1.2GHz in the configurations for SD and NAND boot.
Signed-off-by: Yuan Yao <yao.yuan@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Shaohui Xie [Mon, 17 Oct 2016 08:20:48 +0000 (16:20 +0800)]
armv8: ls2080aqds: fix SGMII repeater settings
The current value to check whether the PHY was configured has dependency
on MC, it expects MC to start PCS AN, this is not true during boot up,
so it should be changed to remove the dependency.
The PHY's register space should be restore to default after accessing
extended space.
Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Hou Zhiqiang [Mon, 31 Oct 2016 02:59:16 +0000 (10:59 +0800)]
fsl: serdes: fix a deadloop issue for P4080
This deadloop is introduced by commit:
71fe222 fsl: serdes: ensure accessing the initialized maps of serdes protocol
deadloop detail:
cpu_init_r => fsl_serdes_init => p4080_erratum_serdes_a005 =>
is_serdes_configured => fsl_serdes_init
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Sriram Dash [Fri, 14 Oct 2016 06:33:50 +0000 (12:03 +0530)]
powerpc: mpc512x: Add support for get_svr() for mpc512x devices
Defines get_svr() for mpc512x devices
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Priyanka Jain [Thu, 3 Nov 2016 12:35:09 +0000 (18:05 +0530)]
driver: net: ldpaa_eth: Fix missing bracket issue
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Priyanka Jain [Thu, 3 Nov 2016 12:20:51 +0000 (17:50 +0530)]
armv8: ls2080a: Update serdes protocol support
Add these serdes protocols
Serdes1: 0x39, 0x4B, 0x4C, 0x4D
Serdes2: 0x47, 0x57
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
[YS: Revise commit message]
Reviewed-by: York Sun <york.sun@nxp.com>
Shaohui Xie [Fri, 28 Oct 2016 06:24:02 +0000 (14:24 +0800)]
armv8: ls1046aqds: add lpuart support
LPUART0 is used by default, and it's using platform clock.
Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Shaohui Xie [Fri, 28 Oct 2016 06:23:30 +0000 (14:23 +0800)]
lpuart: add a get_lpuart_clk function
It's not always true that LPUART clock is CONFIG_SYS_CLK_FREQ. This
patch provides a weak function get_lpuart_clk(), so that the clock
can be ovreridden on a specific board which uses different clock
for LPUART.
Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
[YS: Reformat commit message]
Reviewed-by: York Sun <york.sun@nxp.com>
Feng Li [Thu, 3 Nov 2016 06:15:17 +0000 (14:15 +0800)]
armv7: Add support of ls1021a-iot board
The patch adds support for Freescale ls1021a-iot board.
Signed-off-by: Feng Li <feng.li_2@nxp.com>
[YS: rewrite commit message, fix whitespace in Kconfig]
Reviewed-by: York Sun <york.sun@nxp.com>
Yuan Yao [Tue, 11 Oct 2016 04:13:40 +0000 (12:13 +0800)]
configs: ls2080ardb: Enable DSPI flash support
There is the stmicro DSPI flash on LS12080ARDB.
Enable DSPI flash related configure options.
Signed-off-by: Yuan Yao <yao.yuan@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Pratiyush Srivastava [Mon, 10 Oct 2016 13:15:15 +0000 (18:45 +0530)]
armv8:ls1012a: Update bootargs for fast-boot
Add optimization parameters like "quiet" in bootargs to reduce the system
boot time
Signed-off-by: Pratiyush Mohan Srivastava <pratiyush.srivastava@nxp.com>
Signed-off-by: Harninder Rai <harninder.rai@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Lokesh Vutla [Fri, 14 Oct 2016 05:05:23 +0000 (10:35 +0530)]
ARM: AMx3xx: Allow arch specific code to use early DM
Early system initialization is being done before initf_dm is being called
in U-Boot. Then system will fail to boot if any of the DM enabled driver
is being called in this system initialization code. So, rearrange the
code a bit so that DM enabled drivers can be called during early system
initialization. This is inspired by commit
e850ed82bce8 ("ARM: OMAP4+: Allow
arch specific code to use early DM")
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Andre Przywara [Sun, 20 Nov 2016 14:56:55 +0000 (14:56 +0000)]
drivers: SPI: sunxi SPL: fix warning
Somehow an int returning function without a return statement sneaked
in, fix it.
Also fix some whitespace damage on the way.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Jagan Teki [Wed, 16 Nov 2016 17:57:23 +0000 (23:27 +0530)]
sf: Fix s25fs512s id table
s25fs512s and s25fl512s_256k have common id information
till 5 bytes and 6th byte have different family id
like FS and FL-S as 0x81 and 0x80.
Reported-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Jagan Teki <jagan@openedev.com>
Jagan Teki [Sun, 30 Oct 2016 17:46:30 +0000 (23:16 +0530)]
sf: dataflash: Minor cleanups
- fix single line comments
- remove unneeded spaces
- ascending order of include files
- rename SPI DATAFLASH to dataflash
- rename SPI DataFlash to dataflash
- return NULL replaced with error code
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: York Sun <york.sun@nxp.com>
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Jagan Teki [Sun, 30 Oct 2016 17:46:29 +0000 (23:16 +0530)]
sf: dataflash: Fix add_dataflash return logic
This patch fixed the add_dataflash return logic,
so-that it can handle both jedec and older chips
same as Linux.
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: York Sun <york.sun@nxp.com>
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Jagan Teki [Sun, 30 Oct 2016 17:46:28 +0000 (23:16 +0530)]
sf: dataflash: Move flash id detection into jedec_probe
Flash id detection should be the first step to enumerate
the connected flash on the board, once ie done checking
with respective id codes locally in the driver all this
should be part of jedec_probe instead of id detection and
validated through flash_info{} table separatly.
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: York Sun <york.sun@nxp.com>
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Jagan Teki [Sun, 30 Oct 2016 17:46:27 +0000 (23:16 +0530)]
sf: dataflash: Remove unneeded spi data
dataflash doesn't require options, memory_map from spi.
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: York Sun <york.sun@nxp.com>
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Jagan Teki [Sun, 30 Oct 2016 17:46:26 +0000 (23:16 +0530)]
spi: Remove dual flash options/flags
Dual flash code in spi are usually take the spi controller
to work with dual connected flash devices. Usually these
dual connection operation's are referred to flash controller
protocol rather with spi controller protocol, these are still
present in flash side for the usage of spi-nor controllers.
So, this patch remove the dual_flash options or flags in sf
which are triggered from spi controller side.
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Vignesh R <vigneshr@ti.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Semen Protsenko [Wed, 16 Nov 2016 17:19:06 +0000 (19:19 +0200)]
spl: Remove CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS
This option isn't used for anything, so get rid of it.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Semen Protsenko [Wed, 16 Nov 2016 17:19:05 +0000 (19:19 +0200)]
spl: Convert CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR to Kconfig
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
[trini: Fix sniper and kc1 migration]
Signed-off-by: Tom Rini <trini@konsulko.com>
Jagan Teki [Sun, 30 Oct 2016 17:46:25 +0000 (23:16 +0530)]
sf: Rename few local functions
spi_flash_write_bar-> write_bar
spi_flash_write_bar -> read_bar
spi_flash_cmd_wait_ready -> spi_flash_wait_till_ready
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Vignesh R <vigneshr@ti.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Jagan Teki [Wed, 16 Nov 2016 17:56:19 +0000 (23:26 +0530)]
sf: ids: Use small letter in ext_jedec
Use small 'd' in s25s512s ext_jedec
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Vignesh R <vigneshr@ti.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Jagan Teki [Wed, 16 Nov 2016 17:55:10 +0000 (23:25 +0530)]
sf: ids: Use small letter's with flash name
For readability use small letter's with flash name.
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Vignesh R <vigneshr@ti.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Jagan Teki [Sun, 30 Oct 2016 17:46:22 +0000 (23:16 +0530)]
sf: Rename sf_params.c to spi_flash_ids.c
Now the flash params table as renamed to spi_flash_ids structure,
so rename the sf_params.c to spi_flash_ids.c and remove the legacy.
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Vignesh R <vigneshr@ti.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Jagan Teki [Sun, 30 Oct 2016 17:46:21 +0000 (23:16 +0530)]
sf: Remove non-meaningful comments
Remove unneeded/non-meaningful commit message on
params and flash.
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Vignesh R <vigneshr@ti.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Jagan Teki [Tue, 15 Nov 2016 17:27:42 +0000 (22:57 +0530)]
sf: Remove spansion_s25fss_disable_4KB_erase
In spansion S25FS-S family the physical sectors are grouped as
normal and parameter sectors. Parameter sectors are 4kB in size
with 8 set located at the bottom or top address of a device.
Normal sectors are similar to other flash family with sizes of
64kB or 32 kB.
To erase whole flash using sector erase(D8h or DCh) won't effect
the parameter sectors, so in order to erase these we must use 4K
sector erase commands (20h or 21h) separately.
So better to erase the whole flash using 4K sector erase instead
of detecting these family parts again and do two different erase
operations.
For this:
- Removed spansion_s25fss_disable_4KB_erase code
- Add SECT_4K for S25FS512S chip
Cc: Yunhui Cui <yunhui.cui@nxp.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Vignesh R <vigneshr@ti.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@openedev.com>
Jagan Teki [Sun, 30 Oct 2016 17:46:19 +0000 (23:16 +0530)]
sf: params: Add S25FS256S_64K spi flash support
Add Spansion S25FS256S_64K spi flash to the list of spi_flash_ids.
In spansion S25FS-S family the physical sectors are grouped as
normal and parameter sectors. Parameter sectors are 4kB in size
with 8 set located at the bottom or top address of a device.
Normal sectors are similar to other flash family with sizes of
64kB or 32 kB.
To erase whole flash using sector erase(D8h or DCh) won't effect
the parameter sectors, so in order to erase these we must use 4K
sector erase commands (20h or 21h) separately.
So better to erase the whole flash using 4K sector erase instead
of detecting these family parts again and do two different erase
operations.
Cc: Yunhui Cui <yunhui.cui@nxp.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Vignesh R <vigneshr@ti.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Jagan Teki [Tue, 15 Nov 2016 07:27:52 +0000 (12:57 +0530)]
sf: Add INFO6 flash_info macro
INFO6 is for tabulating 6 byte flash parts, Ex: S25FS256S_64K
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Vignesh R <vigneshr@ti.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@openedev.com>
Jagan Teki [Sun, 30 Oct 2016 17:46:17 +0000 (23:16 +0530)]
sf: Increase max id length by 1 byte
So, now SPI_FLASH_ID_MAX_LEN is 6 bytes useful for
few spansion flash families S25FS-S
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Vignesh R <vigneshr@ti.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Jagan Teki [Sun, 30 Oct 2016 17:46:16 +0000 (23:16 +0530)]
sf: Add SPI_FLASH_MAX_ID_LEN
Add id length of 5 bytes numerical value to macro.
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Vignesh R <vigneshr@ti.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@openedev.com>
Jagan Teki [Sun, 30 Oct 2016 17:46:15 +0000 (23:16 +0530)]
sf: nr_sectors -> n_sectors
Rename nr_sectors as n_sectors to sync with Linux.
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Vignesh R <vigneshr@ti.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Jagan Teki [Sun, 30 Oct 2016 17:46:13 +0000 (23:16 +0530)]
sf: Cleanup spi_flash_info{}
- Proper tabs spaces
- Removed unnecessary
- Add comments in spi_flash_info members
- Add comments for spi_flash_info.flags
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Vignesh R <vigneshr@ti.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Jagan Teki [Sun, 30 Oct 2016 17:46:12 +0000 (23:16 +0530)]
sf: sandbox: Use JEDEC_MFR|ID in id exctract
Instead of extracting id's separately better
to use JEDEC_MFR|ID for code simplicity.
Cc: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@openedev.com>
Jagan Teki [Sun, 30 Oct 2016 17:46:11 +0000 (23:16 +0530)]
sf: Simplify lock ops detection code
Simplify the flash_lock ops detection code and added
meaningful comment.
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Vignesh R <vigneshr@ti.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@openedev.com>
Jagan Teki [Sun, 30 Oct 2016 17:46:10 +0000 (23:16 +0530)]
sf: Adopt flash table INFO macro from Linux
INFO macro make flash table entries more adjustable like
adding new flash_info attributes, update ID length bytes
and so on and more over it will sync to Linux way of defining
flash_info attributes.
- Add JEDEC_ID
- Add JEDEC_EXT macro
- Add JEDEC_MFR
- spi_flash_params => spi_flash_info
- params => info
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Vignesh R <vigneshr@ti.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@openedev.com>
Signed-off-by: Jagan Teki <jagan@openedev.com>
Chris Packham [Thu, 27 Oct 2016 08:16:05 +0000 (21:16 +1300)]
spi: kirkwood_spi: implement mvebu_spi_set_mode()
Set the appropriate bits in the interface config register based
on the SPI_ mode flags.
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Tom Rini [Thu, 17 Nov 2016 16:46:56 +0000 (11:46 -0500)]
Merge branch 'master' of git.denx.de/u-boot-mmc
Tom Rini [Thu, 17 Nov 2016 16:46:45 +0000 (11:46 -0500)]
Merge tag 'signed-efi-next' of git://github.com/agraf/u-boot
Patch queue for efi - 2016-11-17
Highlights this time around:
- x86 efi_loader support
- hello world efi test case
- network device name is now representative
- terminal output reports modes correctly
- fix psci reset for ls1043/ls1046
- fix efi_add_runtime_mmio definition for x86
- efi_loader support for ls2080
Alexander Graf [Thu, 17 Nov 2016 00:03:02 +0000 (01:03 +0100)]
ls2080ardb: Convert to distro boot
Most new systems in U-Boot these days make use of the generic "distro"
framework which allows a user to have U-Boot scan for a bootable OS
on all available media types.
This patch extends the LS2080ARDB board to use that framework if the
hard coded NOR flash location does not contain a bootable image.
Signed-off-by: Alexander Graf <agraf@suse.de>
Alexander Graf [Thu, 17 Nov 2016 00:03:01 +0000 (01:03 +0100)]
armv8: fsl-layerscape: Add support for efi_loader RTS reset
When implementing efi loader support, we can expose runtime services
for payloads. One such service is CPU reset.
This patch implements RTS CPU reset support for layerscape systems.
Signed-off-by: Alexander Graf <agraf@suse.de>
Reviewed-by: York Sun <york.sun@nxp.com>
Alexander Graf [Thu, 17 Nov 2016 00:03:00 +0000 (01:03 +0100)]
armv8: ls2080a: Declare spin tables as reserved for efi loader
The efi loader code has its own memory map, so it needs to be aware where
the spin tables are located, to ensure that no code writes into those
regions.
Signed-off-by: Alexander Graf <agraf@suse.de>
Alexander Graf [Thu, 17 Nov 2016 00:02:59 +0000 (01:02 +0100)]
ls2080ardb: Reserve DP-DDR RAM
The DP-DDR shouldn't be exposed as conventional memory to an OS, so let's
rather claim it's a reserved region in the EFI memory map
Signed-off-by: Alexander Graf <agraf@suse.de>
Reviewed-by: York Sun <york.sun@nxp.com>
Alexander Graf [Thu, 17 Nov 2016 00:02:57 +0000 (01:02 +0100)]
ls2080: Exit dpaa only right before exiting U-Boot
On ls2080 we have a separate network fabric component which we need to
shut down before we enter Linux (or any other OS). Along with that also
comes configuration of the fabric using a description file.
Today we always stop and configure the fabric in the boot script and
(again) exit it on device tree generation. This works ok for the normal
booti case, but with bootefi the payload we're running may still want to
access the network.
So let's add a new fsl_mc command that defers configuration and stopping
the hardware to when we actually exit U-Boot, so that we can still use
the fabric from an EFI payload.
For existing boot scripts, nothing should change with this patch.
Signed-off-by: Alexander Graf <agraf@suse.de>
Reviewed-by: York Sun <york.sun@nxp.com>
[agraf: Fix x86 build]
Alexander Graf [Thu, 17 Nov 2016 00:02:56 +0000 (01:02 +0100)]
efi_loader: Fix efi_add_runtime_mmio definition
The efi_add_runtime_mmio prototype for disabled CONFIG_EFI_LOADER
was different from the enabled one. Sync them.
Signed-off-by: Alexander Graf <agraf@suse.de>
Alexander Graf [Thu, 17 Nov 2016 00:02:55 +0000 (01:02 +0100)]
efi_loader: Disable PSCI reset for ls1043 and ls1046
The NXP ls1043 and ls1046 systems do not (yet) have PSCI enablement
for reset. Don't enable generic PSCI reset code on them.
Signed-off-by: Alexander Graf <agraf@suse.de>
Alexander Graf [Thu, 17 Nov 2016 00:02:58 +0000 (01:02 +0100)]
efi_loader: AArch64: Run EFI payloads in EL2 if U-Boot runs in EL3
Some boards decided not to run ATF or other secure firmware in EL3, so
they instead run U-Boot there. The uEFI spec doesn't know what EL3 is
though - it only knows about EL2 and EL1. So if we see that we're running
in EL3, let's get into EL2 to make payloads happy.
Signed-off-by: Alexander Graf <agraf@suse.de>
Reviewed-by: York Sun <york.sun@nxp.com>
Maxime Ripard [Fri, 4 Nov 2016 15:18:11 +0000 (16:18 +0100)]
sunxi: sina33: Enable the LCD
The SinA33 comes with an optional 7" display. Enable it in the
configuration.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Maxime Ripard [Fri, 4 Nov 2016 15:18:10 +0000 (16:18 +0100)]
sunxi: sina33: Enable the eMMC
The SinA33 has an 4GB Toshiba eMMC connected to the MMC2 controller.
Enable it.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Maxime Ripard [Fri, 4 Nov 2016 15:18:09 +0000 (16:18 +0100)]
mmc: sunxi: Enable 8bits bus width for sun8i
The sun8i SoCs also have a 8 bits capable MMC2 controller. Enable the
support for those too.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Maxime Ripard [Fri, 4 Nov 2016 15:18:08 +0000 (16:18 +0100)]
mmc: Retry the switch command
Some eMMC will fail at the first switch, but would succeed in a subsequent
one.
Make sure we try several times to cover those cases. The number of retries
(and the behaviour) is currently what is being used in Linux.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Bharat Kumar Gogada [Tue, 2 Aug 2016 15:04:13 +0000 (20:34 +0530)]
ARM64: zynqmp: Adding prefetchable memory space to pcie
Adding prefetchable memory space to pcie device tree node.
Shifting configuration space to 64-bit address space.
Removing pcie device tree node from amba as it requires size-cells=<2>
in order to access 64-bit address space.
Signed-off-by: Bharat Kumar Gogada <bharatku@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Kedareswara rao Appana [Fri, 30 Sep 2016 05:04:59 +0000 (10:34 +0530)]
ARM64: zynqmp: Add clocks for LPDDMA
Zynqmp DMA driver expects two clocks (main clock and apb clock)
For LPDDMA channels the two clocks are missing in the
Dma node resulting probe failure.
xilinx-zynqmp-dma
ffa80000.dma: main clock not found.
xilinx-zynqmp-dma
ffa80000.dma: Probing channel failed
xilinx-zynqmp-dma: probe of
ffa80000.dma failed with error -2
This patch fixes this issue.
Signed-off-by: Kedareswara rao Appana <appanad@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Kedareswara rao Appana [Fri, 9 Sep 2016 07:06:01 +0000 (12:36 +0530)]
ARM64: zynqmp: Add description for LPDDMA channel usage
LPDDMA default allows only secured access.
inorder to enable these dma channels,
one should ensure that it allows non secure access.
This patch updates the same.
Reported-by: Sai Pavan Boddu <saipava@xilinx.com>
Signed-off-by: Kedareswara rao Appana <appanad@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Thu, 11 Feb 2016 06:19:06 +0000 (07:19 +0100)]
ARM64: zynqmp: Use 64bit size cell format for main amba bus
Use 64bit size cell for main amba bus instead of 32bit because PCIe
node requires it Change 64bit sizes also for all others IPs.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Naga Sureshkumar Relli [Wed, 18 May 2016 06:53:13 +0000 (12:23 +0530)]
ARM64: zynqmp: Add ocm node in dtsi
This patch adds ocm controller node in zynqmp.dtsi.
needed for OCM edac support.
Signed-off-by: Naga Sureshkumar Relli <nagasure@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Anurag Kumar Vulisha [Tue, 17 May 2016 11:19:01 +0000 (16:49 +0530)]
ARM64: zynqmp: Add device tree properties for ZynqMP GT core
This patch adds the ZynqMP GT core device-tree properties for
zynqmp.dtsi file.
Signed-off-by: Anurag Kumar Vulisha <anuragku@xilinx.com>
Tested-by: Hyun Kwon <hyunk@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Thu, 20 Oct 2016 08:36:05 +0000 (10:36 +0200)]
Revert "ARM64: zynqmp: Added broken-tuning property to SD, eMMC nodes"
This reverts commit
bd750e7a6c515c081b72d4ef108a2bfa691a3fd1
Implemented the new workaround for auto tuning based on
zynqmp compatible string, so removed the 'broken-tuning'
property.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Sai Krishna Potthuri [Tue, 16 Aug 2016 09:11:35 +0000 (14:41 +0530)]
ARM64: zynqmp: change sdhci compatible string.
This patch changes the compatible string for sdhci node,
adds "xlnx,device_id" and "xlnx,mio_bank" property to sdhci node.
Signed-off-by: Sai Krishna Potthuri <lakshmis@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Wed, 6 Apr 2016 08:43:23 +0000 (10:43 +0200)]
ARM64: zynqmp: List all SMMU ids
Add SMMU description for all tested IPs.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Nava kishore Manne [Sat, 20 Aug 2016 18:47:52 +0000 (00:17 +0530)]
ARM64: zynqmp: Add support for zynqmp fpga manager
Add support for zynqmp fpga manager.
Signed-off-by: Nava kishore Manne <navam@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Naga Sureshkumar Relli [Mon, 20 Jun 2016 10:18:30 +0000 (15:48 +0530)]
ARM64: zynqmp: Add cortexa53 edac node
This patch adds edac node for arm cortexa53 to report
errors on L1 and L2 caches.
Signed-off-by: Naga Sureshkumar Relli <nagasure@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Thu, 20 Oct 2016 08:38:16 +0000 (10:38 +0200)]
Revert "ARM64: zynqmp: Add serdes address space dp driver"
This reverts commit
786db82bd5bf09cc8f78c8b14445e843d7566b1c.
Since we are using serdes driver , no need of mapping serdes register
space into DP driver.
Signed-off-by: Anurag Kumar Vulisha <anuragku@xilinx.com>
Tested-by: Hyun Kwon <hyunk@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Hyun Kwon [Fri, 15 Jul 2016 00:42:44 +0000 (17:42 -0700)]
ARM64: zynqmp: drm: Add DMA index
Each plane can be associated with multiple DMA channels. So add
index for each DMA channel.
Signed-off-by: Hyun Kwon <hyun.kwon@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Thu, 20 Oct 2016 08:26:13 +0000 (10:26 +0200)]
ARM64: zynqmp: Sync gpio node properties
Keep dtsi in sync with mainline kernel.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Tue, 9 Aug 2016 13:06:58 +0000 (15:06 +0200)]
ARM64: zynqmp: Remove xlnx,id property
Remove unused xlnx,id property because it is not the part of
DT binding.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Bharat Kumar Gogada [Tue, 19 Jul 2016 15:19:29 +0000 (20:49 +0530)]
ARM64: zynqmp: pci: Updating device tree as per upstream
Updating required device tree changes as per mainlined driver
from 4.6 kernel.
Signed-off-by: Bharat Kumar Gogada <bharatku@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Filip Drazic [Mon, 29 Aug 2016 17:32:59 +0000 (19:32 +0200)]
ARM64: zynqmp: Support for multiple PM IDs assigned to a PM domain
Previously, it was assumed that there is a 1:1 mapping between
PM ID defined in the platform firmware and a PM domain. However, there
can be a situation where multiple PM IDs belong to a single PM domain
(e.g. PM IDs for GPU and two pixel processors correspond to a single
PM domain).
This patch adds support for assigning more than one PM ID to
a single PM domain.
Updated documentation accordingly.
Assigned pixel processors PM IDs to GPU PM domain.
Signed-off-by: Filip Drazic <filip.drazic@aggios.com>
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Filip Drazic [Mon, 29 Aug 2016 17:32:56 +0000 (19:32 +0200)]
ARM64: zynqmp: DT: Add PM domains for GPU and PCIE
Signed-off-by: Filip Drazic <filip.drazic@aggios.com>
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Filip Drazic [Thu, 25 Aug 2016 16:58:51 +0000 (18:58 +0200)]
ARM64: zynqmp: DT: Remove unused PM domains for PLL
Signed-off-by: Filip Drazic <filip.drazic@aggios.com>
Acked-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Filip Drazic [Thu, 25 Aug 2016 16:58:49 +0000 (18:58 +0200)]
ARM64: zynqmp: DT: Remove unused DDR PM domain
DDR power states are handled by the PM firmware, so this domain is
redundant. Also, since there is no device using this PM domain,
it will be powered off during boot, which is wrong.
Signed-off-by: Filip Drazic <filip.drazic@aggios.com>
Acked-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Wed, 19 Oct 2016 14:07:58 +0000 (16:07 +0200)]
ARM64: zynqmp: Remove note about level shifter on zcu102
i2c device is just level shifter. Remove reference from dts.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Fri, 9 Sep 2016 06:46:39 +0000 (08:46 +0200)]
ARM64: zynqmp: Add dcc port to dtsi
Add dcc to dtsi for supporting system without serial port.
DCC is enabled by default on ZynqMP.
Adding dcc to zcu100 and zcu102 which were tested.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Wed, 25 May 2016 18:09:35 +0000 (20:09 +0200)]
ARM64: zynqmp: Add gpio-keys for zcu102
There is gpio push button on MIO22. Add it to DTS to have full board
description.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Wed, 20 Apr 2016 11:12:25 +0000 (13:12 +0200)]
ARM64: zynqmp: Enable gpio-led as heartbeat on zcu102
Show user that Linux is alive on the board.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Naga Sureshkumar Relli [Tue, 12 Apr 2016 06:16:11 +0000 (11:46 +0530)]
ARM64: zynqmp: Enable can1 for ep108
This patch enables can1 for ep108.
Signed-off-by: Naga Sureshkumar Relli <nagasure@xilinx.com>
Reviewed-by: Kedareswara rao Appana <appanad@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
VNSL Durga [Mon, 11 Apr 2016 12:13:47 +0000 (17:43 +0530)]
ARM64: zynqmp: Added clocks to DT for ep108
Added clks for ep108 platform.
Signed-off-by: VNSL Durga <vnsldurg@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Kedareswara rao Appana [Fri, 9 Sep 2016 07:06:00 +0000 (12:36 +0530)]
ARM64: zynqmp: Add clocks for LPDDMA
Zynqmp DMA driver expects two clocks (main clock and apb clock)
LPDDMA clock cofiguration is missing for the same in the
zynqmp-clk.dtsi file.
This patch updates for the same.
Reported-by: Sai Pavan Boddu <saipava@xilinx.com>
Signed-off-by: Kedareswara rao Appana <appanad@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Fri, 11 Nov 2016 12:21:04 +0000 (13:21 +0100)]
ARM64: zynqmp: Remove DTC 1.4.2 warnings
DTC 1.4.2 reports these warnings:
Warning (unit_address_vs_reg): Node /amba_apu has a reg or ranges
property, but no unit name
Warning (unit_address_vs_reg): Node /amba has a reg or ranges property,
but no unit name
Warning (unit_address_vs_reg): Node /amba/usb@
fe200000 has a unit name,
but no reg property
Warning (unit_address_vs_reg): Node /amba/usb@
fe300000 has a unit name,
but no reg property
Warning (unit_address_vs_reg): Node
/amba/dma@
fd4c0000/dma-video0channel@
fd4c0000 has a unit name, but no
reg property
Warning (unit_address_vs_reg): Node
/amba/dma@
fd4c0000/dma-video1channel@
fd4c0000 has a unit name, but no
reg property
Warning (unit_address_vs_reg): Node
/amba/dma@
fd4c0000/dma-video2channel@
fd4c0000 has a unit name, but no
reg property
Warning (unit_address_vs_reg): Node
/amba/dma@
fd4c0000/dma-graphicschannel@
fd4c0000 has a unit name, but no
reg property
Warning (unit_address_vs_reg): Node
/amba/dma@
fd4c0000/dma-audio0channel@
fd4c0000 has a unit name, but no
reg property
Warning (unit_address_vs_reg): Node
/amba/dma@
fd4c0000/dma-audio1channel@
fd4c0000 has a unit name, but no
reg property
Warning (unit_address_vs_reg): Node /memory has a reg or ranges
property, but no unit name
This patch is fixing them.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Fri, 11 Nov 2016 12:11:37 +0000 (13:11 +0100)]
ARM: zynq: Remove DTC 1.4.2 warnings
DTC 1.4.2 reports these warnings:
Warning (unit_address_vs_reg): Node /memory has a reg or ranges
property, but no unit name
Warning (unit_address_vs_reg): Node /pmu has a reg or ranges property,
but no unit name
Warning (unit_address_vs_reg): Node /fixedregulator@0 has a unit name,
but no reg property
This patch is fixing them.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Siva Durga Prasad Paladugu [Tue, 1 Nov 2016 18:19:53 +0000 (23:49 +0530)]
ARM64: zynqmp: Correct the sdhci minimum frequency for ep108
Correct the sdhci minimum frequency for ep platform.
It should be right shift instead of left shift operand.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Thu, 14 Jul 2016 09:13:04 +0000 (11:13 +0200)]
ARM64: zynqmp: Ignore warnings from autogenerated files
Autogenerated files contain casting issues and missing function
declaration and even usleep implementation. Suppress them for now
till these files are fixed.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Tue, 25 Oct 2016 09:43:02 +0000 (11:43 +0200)]
ARM64: zynqmp: Fix secondary bootmode enabling
Do not setup use_alt bit which copy alternative boot mode to
boot mode. The reason is that this bit is cleared after POR
but not after any software reset which will cause
that after SW reset bootrom will look for different boot image.
This patch setups alternative boot mode selection (purely SW
handling) and extends code to read this alternative boot mode first and
use it if it is setup.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>