Andrew Gabbasov [Mon, 1 Dec 2014 12:59:12 +0000 (06:59 -0600)]
mmc: dw_mmc: Use active DDR mode flag
The card_caps bit should denote the card capability to use DDR mode,
but we need the flag indicating that the DDR mode is active.
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Andrew Gabbasov [Mon, 1 Dec 2014 12:59:11 +0000 (06:59 -0600)]
mmc: Fix block length for DDR mode
Block length for write and read commands is fixed to 512 bytes
when the card is in Dual Data Rate mode. If block length read from CSD
is different, make sure the driver will use correct length
in all further calculations and settings.
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Andrew Gabbasov [Mon, 1 Dec 2014 12:59:10 +0000 (06:59 -0600)]
mmc: Fix Dual Data Rate capability recognition
Since the driver doesn't work in 1.2V or 1.8V signaling level modes,
Dual Data Rate mode can be supported by the driver only if it is supported
by the card in regular 3.3V mode. So, check for a particular single
bit in card type field.
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Andrew Gabbasov [Mon, 1 Dec 2014 12:59:09 +0000 (06:59 -0600)]
mmc: Fix handling of bus widths and DDR card capabilities
If the MMC_MODE_DDR_52MHz flag is set in card capabilities bitmask,
it is never cleared, even if switching to DDR mode fails, and if
the controller driver uses this flag to check the DDR mode, it can
take incorrect actions.
Also, DDR related checks in mmc_startup() incorrectly handle the case
when the host controller does not support some bus widths (e.g. can't
support 8 bits), since the host_caps is checked for DDR bit, but not
bus width bits.
This fix clearly separates using of card_caps bitmask, having there
the flags for the capabilities, that the card can support, and actual
operation mode, described outside of card_caps (i.e. bus_width and
ddr_mode fields in mmc structure). Separate host controller drivers
may need to be updated to use the actual flags. Respectively,
the capabilities checks in mmc_startup are made more correct and clear.
Also, some clean up is made with errors handling and code syntax layout.
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Jaehoon Chung [Fri, 28 Nov 2014 11:42:33 +0000 (20:42 +0900)]
mmc: exynos_dw-mmc: change debug message
To debug more exactly, add the index for device.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Markus Niebel [Tue, 18 Nov 2014 14:13:53 +0000 (15:13 +0100)]
MMC: add MMC_VERSION_5_0
Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Markus Niebel [Tue, 18 Nov 2014 14:11:42 +0000 (15:11 +0100)]
MMC: fix user capacity for partitioned eMMC card
if the card claims to be high capacity and the card
is partitioned the capacity shall still be read from
ext_csd SEC_COUNT even if the resulting capacity is
smaller than 2 GiB
Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Lubomir Popov [Tue, 11 Nov 2014 10:25:42 +0000 (12:25 +0200)]
mmc: Cosmetic fix for nicer, aligned device list printout
If print_mmc_devices() was called with a '\n' separator (as done
for example by the "mmc list" command), it offset the 2-nd and
all subsequent lines by one space. Fixing this.
Signed-off-by: Lubomir Popov <l-popov@ti.com>
Tom Rini [Thu, 11 Dec 2014 23:40:49 +0000 (18:40 -0500)]
Merge branch 'master' of git://git.denx.de/u-boot-usb
Conflicts:
board/freescale/mx6sxsabresd/mx6sxsabresd.c
Signed-off-by: Tom Rini <trini@ti.com>
Tom Rini [Thu, 11 Dec 2014 23:28:09 +0000 (18:28 -0500)]
Merge branch 'master' of git://git.denx.de/u-boot-fsl-qoriq
Xiubo Li [Thu, 11 Dec 2014 19:15:26 +0000 (11:15 -0800)]
ARM: HYP/non-sec: Fix the ARCH Timer frequency setting for sun7i
Earlier commit
73a1cb27 mistakenly used CONFIG_SYS_TIMER_CLK_FREQ.
It should be CONFIG_TIMER_CLK_FREQ.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
[York Sun: This is the difference between two patch versions]
Reviewed-by: York Sun <yorksun@freescale.com>
Alison Wang [Wed, 3 Dec 2014 08:18:09 +0000 (16:18 +0800)]
kconfig: ls102xa: Change the prompt messages
As NOR/NAND/SD boot are all supported on LS1021AQDS/TWR
boards, the prompt message "Support ls1021aqds_nor" in
Kconfig is not clear. This patch changes it to
"Support ls1021aqds".
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Jaiprakash Singh [Thu, 27 Nov 2014 07:08:12 +0000 (12:38 +0530)]
driver/mtd: Fix IFC compilation warnings
'eccstat' array elements might be used uninitialized
Signed-off-by: Jaiprakash Singh <b44839@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Xiubo Li [Fri, 21 Nov 2014 09:40:59 +0000 (17:40 +0800)]
ARM: ls102xa: Setting device's stream id for SMMUs.
LS1 has 4 SMMUs for address translation of the masters. All the
SMMUs' stream IDs are 8-bit. The address translation depends on the
stream ID of the incoming transaction.
Each master has unique stream ID assigned to it and is configurable
through SCFG registers. The stream ID for the masters is identical
and share the same register field of STREAM ID registers.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Xiubo Li [Fri, 21 Nov 2014 09:40:58 +0000 (17:40 +0800)]
ARM: ls102xa: allow all the peripheral access permission as R/W.
The Central Security Unit (CSU) allows secure world software to
change the default access control policies of peripherals/bus
slaves, determining which bus masters may access them. This
allows peripherals to be separated into distinct security domains.
Combined with SMMU configuration of the system masters privileges,
these features provide protection against indirect unauthorized
access to data.
For now we configure all the peripheral access permissions as R/W.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Xiubo Li [Fri, 21 Nov 2014 09:40:57 +0000 (17:40 +0800)]
ls102xa: changing a few targets' configurations.
Enable hypervisors utilizing the ARMv7 virtualization extension
on the LS1021A-QDS/TWR boards with the A7 core tile, we add the
required configuration variable.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Xiubo Li [Fri, 21 Nov 2014 09:40:56 +0000 (17:40 +0800)]
ls1021a: adding a secondary core boot address and kick functions
Define the board specific smp_set_cpu_boot_addr() function to set
the start address for secondary cores in the LS1021A specific manner.
Define the board specific smp_kick_all_cpus() functioin to boot a
secondary core. Here the BRR contains control bits for enabling boot
for each core. On exiting HRESET or PORESET, the RCW BOOT_HO field
optionally allows for logical core 0 to be released for booting or to
remain in boot holdoff. All other cores remain in boot holdoff until
their corresponding bit is set.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Xiubo Li [Fri, 21 Nov 2014 09:40:55 +0000 (17:40 +0800)]
ARM: HYP/non-sec: Fix the ARCH Timer frequency setting.
For some SoCs, the system clock frequency may not equal to the
ARCH Timer's frequency.
This patch uses the CONFIG_TIMER_CLK_FREQ instead of
CONFIG_SYS_CLK_FREQ, then the system clock macro and arch timer
macor could be set separately and without interfering each other.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Xiubo Li [Fri, 21 Nov 2014 09:40:54 +0000 (17:40 +0800)]
ARM: HYP/non-sec: add the pen address BE mode support.
For some SoCs, the pen address register maybe in BE mode and the
CPUs are in LE mode.
This patch adds BE mode support for smp pen address.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Tang Yuantian [Fri, 21 Nov 2014 03:17:15 +0000 (11:17 +0800)]
fsl/sleep: updated the deep sleep framework for QorIQ platforms
With the introducing of generic board and ARM-based cores, current
deep sleep framework doesn't work anymore.
This patch will convert the current framework to adapt this change.
Basically it does:
1. Converts all the Freescale's DDR driver to support deep sleep.
2. Added basic framework support for ARM-based and PPC-based
cores separately.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Nikhil Badola [Thu, 30 Oct 2014 04:41:28 +0000 (10:11 +0530)]
drivers: usb: fsl: Check USB Erratum A007792 applicability
Check USB Erratum A007792 applicability. If applicable, add
corresponding property in the device tree via device tree fixup
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Nikhil Badola [Tue, 30 Sep 2014 05:54:07 +0000 (11:24 +0530)]
drivers: usb: fsl: Add USB device-tree errata framework
Add a new framework for fsl usb erratum handling to standardize
erratum checking only inside Uboot. Information to kernel is passed
via a boolean property corresponding to erratum, hence eliminating
need for code duplication inside kernel
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Nikhil Badola [Mon, 20 Oct 2014 11:20:49 +0000 (16:50 +0530)]
drivers: usb: Make usb device-tree fixup code architecture independent
move usb device tree fixup code from "arch/powerpc/" to "drivers/usb/"
so that it works independent of architecture it is running on
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Yao Yuan [Wed, 26 Nov 2014 06:54:33 +0000 (14:54 +0800)]
ls1021aqds: add hwconfig setting to do pin mux
The Freescale LS1021AQDS share some pins, so Add the hwconfig option
that allows the user to choose which the function he wants.
The main pin mux IP is:
eSDHC, SAI, IIC2, RGMII, CAN, SAI.
Signed-off-by: Yuan Yao <yao.yuan@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Alison Wang [Tue, 9 Dec 2014 09:38:14 +0000 (17:38 +0800)]
arm: ls102xa: Add NAND boot support for LS1021AQDS board
This patch adds NAND boot support for LS1021AQDS board. SPL
framework is used. PBL initialize the internal RAM and copy
SPL to it, then SPL initialize DDR using SPD and copy u-boot
from NAND flash to DDR, finally SPL transfer control to u-boot.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Alison Wang [Tue, 9 Dec 2014 09:38:02 +0000 (17:38 +0800)]
arm: ls102xa: Add QSPI boot support for LS1021AQDS/TWR board
This patch adds QSPI boot support for LS1021AQDS/TWR board.
The QSPI boot image need to be programmed into the QSPI flash
first. Then the booting will start from QSPI memory space.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Alison Wang [Tue, 9 Dec 2014 09:37:49 +0000 (17:37 +0800)]
arm: ls102xa: Fix SD/NAND/QSPI boot defination error for QE support
The SD/NAND/QSPI boot definations are wrong for QE support, this
patch is to fix this error.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Alison Wang [Tue, 9 Dec 2014 09:37:34 +0000 (17:37 +0800)]
arm: ls1021a: Add CONFIG_DOS_PARTITION and CONFIG_CMD_FAT support
This patch will fix the bug that the partitions on the SD card could
not be accessed and add the support for the FAT fs.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Alison Wang [Wed, 3 Dec 2014 07:00:48 +0000 (15:00 +0800)]
arm: ls102xa: Add SD boot support for LS1021ATWR board
This patch adds SD boot support for LS1021ATWR board. SPL
framework is used. PBL initialize the internal RAM and copy
SPL to it, then SPL initialize DDR using SPD and copy u-boot
from SD card to DDR, finally SPL transfer control to u-boot.
Signed-off-by: Chen Lu <chen.lu@freescale.com>
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Signed-off-by: Jason Jin <jason.jin@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Alison Wang [Wed, 3 Dec 2014 07:00:47 +0000 (15:00 +0800)]
arm: ls102xa: Add SD boot support for LS1021AQDS board
This patch adds SD boot support for LS1021AQDS board. SPL
framework is used. PBL initialize the internal RAM and copy
SPL to it, then SPL initialize DDR using SPD and copy u-boot
from SD card to DDR, finally SPL transfer control to u-boot.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Signed-off-by: Jason Jin <jason.jin@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Alison Wang [Wed, 3 Dec 2014 07:00:46 +0000 (15:00 +0800)]
ls102xa: qixis: Add CONFIG_QIXIS_I2C_ACCESS macro
Through adding CONFIG_QIXIS_I2C_ACCESS macro,
QIXIS_READ(reg)/QIXIS_WRITE(reg, value) can be used
for both i2c and ifc access to QIXIS FPGA. This is
more convenient for coding.
Signed-off-by: Jason Jin <jason.jin@freescale.com>
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Alison Wang [Wed, 3 Dec 2014 07:00:45 +0000 (15:00 +0800)]
kconfig: ls1021a: add SUPPORT_SPL
Add SUPPORT_SPL feature for SD and NAND boot on
LS1021AQDS and LS1021ATWR.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Alison Wang [Wed, 3 Dec 2014 07:00:43 +0000 (15:00 +0800)]
arm: spl: Add I2C linker list in generic .lds
On LS1, DDR is initialized by reading SPD through I2C interface
in SPL code. For I2C, ll_entry_count() is called, and it returns
the number of elements of a linker-generated array placed into
subsection of .u_boot_list section specified by _list argument.
So add I2C linker list in the generic .lds to fix the issue about
using I2C in SPL.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Alison Wang [Wed, 3 Dec 2014 07:00:42 +0000 (15:00 +0800)]
spl: Use u-boot.img instead of u-boot.bin
In SD boot, the magic number of u-boot image will be checked.
For LS102xA, u-boot.bin doesn't have the magic number. So use
u-boot.img which includes the magic number instead of u-boot.bin
when producing u-boot-with-spl-pbl.bin.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Alison Wang [Wed, 3 Dec 2014 07:00:41 +0000 (15:00 +0800)]
ls102xa: pblimage: Add pblimage tool support for LS102xA
For LS102xA, the size of spl/u-boot-spl.bin is variable.
This patch adds the support to deal with the variable
u-boot size in pblimage tool. It will be padded to 64
byte boundary.
Use pblimage_check_params() to add the specific operations
for ARM, such as PBI CRC and END command and the calculation
of pbl_cmd_initaddr.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Chenhui Zhao [Thu, 6 Nov 2014 02:51:59 +0000 (10:51 +0800)]
ls1021aqds: set the default I2C channel before DDR init
When resuming from deep sleep, the I2C channel may not be
in the default channel. So, switch to the default channel
before accessing DDR SPD.
Signed-off-by: Chenhui Zhao <chenhui.zhao@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Minghuan Lian [Fri, 31 Oct 2014 05:43:44 +0000 (13:43 +0800)]
arm: ls102xa: Update PCIe dts node status
The patch changes PCIe dts node status to 'disabled' if the
corresponding controller is disabled according to serdes protocol.
Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
chenhui zhao [Wed, 22 Oct 2014 10:20:22 +0000 (18:20 +0800)]
arm: ls102xa: clear EPU registers for deep sleep
After wakeup from deep sleep, Clear EPU registers as early as possible
to prevent from possible issue. It's also safe to clear at normal boot.
Signed-off-by: Chenhui Zhao <chenhui.zhao@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Tang Yuantian [Tue, 21 Oct 2014 05:51:58 +0000 (13:51 +0800)]
arm: ls102xa: fixed a bus frequency setting error
The bus frequency in SOC node should be clock frequency of platform.
That is not true if it is devided by 2.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Tom Rini [Wed, 10 Dec 2014 14:07:25 +0000 (09:07 -0500)]
Merge branch 'master' of git://denx.de/git/u-boot-imx
Tom Rini [Wed, 10 Dec 2014 14:07:06 +0000 (09:07 -0500)]
Merge branch 'rmobile' of git://git.denx.de/u-boot-sh
Nobuhiro Iwamatsu [Wed, 3 Dec 2014 06:30:30 +0000 (15:30 +0900)]
arm: rmobile: alt: Add support MMC and MMC command
Alt board has been connected to eMMC of 8GB to MMC port.
This enables MMC port and MMC command.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Nobuhiro Iwamatsu [Wed, 3 Dec 2014 06:30:30 +0000 (15:30 +0900)]
arm: rmobile: lager: Add support MMC and MMC command
Lager board has been connected to eMMC of 8GB to MMC1 port.
This enables MMC1 port and MMC command.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Nobuhiro Iwamatsu [Wed, 10 Dec 2014 01:46:04 +0000 (10:46 +0900)]
arm: rmobile: rcar: Add support ext2 and ext4 file system
Board with R-Car SoC has USB and MMC. They might use the EXT2 or EXT4 file system.
This adds support ext2 and ext4 file system
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Nobuhiro Iwamatsu [Wed, 10 Dec 2014 05:12:43 +0000 (14:12 +0900)]
arm: rmobile: Add mmc.h for sh_mmcif of rmobile
R-Mobile and R-Car ARM SoCs use sh_mmcif as MMC host driver.
This adds arch-rmobile/mmc.h that defines mmcif_mmc_init().
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Vikas Manocha [Mon, 1 Dec 2014 20:27:54 +0000 (12:27 -0800)]
dm: stv0991: Move serial to driver model
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
Vikas Manocha [Mon, 1 Dec 2014 20:27:53 +0000 (12:27 -0800)]
stv0991: increase the initial ram size config
It is done to make space available for driver model memory.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
Vikas Manocha [Tue, 18 Nov 2014 18:42:24 +0000 (10:42 -0800)]
stv0991: enable default and misc command configs
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
Vikas Manocha [Tue, 18 Nov 2014 18:42:23 +0000 (10:42 -0800)]
stv0991: enable ethernet support
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
Vikas Manocha [Tue, 18 Nov 2014 18:42:22 +0000 (10:42 -0800)]
stv0991: Add basic stv0991 architecture support
stv0991 architecture support added. It contains the support for
following blocks
- Timer
- uart
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
[trini: Add arch/arm/cpu/armv7/Makefile hunk]
Signed-off-by: Tom Rini <trini@ti.com>
Tom Rini [Mon, 8 Dec 2014 21:33:13 +0000 (16:33 -0500)]
Prepare v2015.01-rc3
Signed-off-by: Tom Rini <trini@ti.com>
Tom Rini [Mon, 8 Dec 2014 21:35:07 +0000 (16:35 -0500)]
Merge git://git.denx.de/u-boot-mpc85xx
Tom Rini [Mon, 8 Dec 2014 21:35:06 +0000 (16:35 -0500)]
Merge branch 'master' of git://git.denx.de/u-boot-ti
Tom Rini [Mon, 8 Dec 2014 21:35:05 +0000 (16:35 -0500)]
Merge git://git.denx.de/u-boot-i2c
Tom Rini [Mon, 8 Dec 2014 21:35:05 +0000 (16:35 -0500)]
Merge branch 'master' of git://git.denx.de/u-boot-uniphier
Masahiro Yamada [Fri, 5 Dec 2014 15:03:26 +0000 (00:03 +0900)]
ARM: UniPhier: detect the number of flash banks at run-time
Some UniPhier boards are equipped with an expansion slot that
some optional SRAM/NOR-flash cards can be attached to. So, run-time
detection of the number of flash banks would be more user-friendly.
Until this commit, UniPhier boards have achieved this by (ab)using
board_flash_wp_on() because the boot failed if flash_size got zero.
Fortunately, this problem was solved by commit
70879a92561a (flash:
do not fail even if flash_size is zero).
Now it is possible to throw away such a tricky workaround. This
commit also enables CONFIG_SYS_MAX_FLASH_BANKS_DETECT for further
refactoring.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Masahiro Yamada [Fri, 5 Dec 2014 15:03:25 +0000 (00:03 +0900)]
ARM: UniPhier: extend register area of init page table for PH1-sLD3
0x20000000-0x2fffffff: assigned to ARM mpcore (sLD3 only)
0xf0000000-0xffffffff: assigned to Denali NAND controller (sLD3 only)
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Masahiro Yamada [Fri, 5 Dec 2014 15:03:24 +0000 (00:03 +0900)]
ARM: UniPhier: add device tree sources for PH1-sLD3
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Masahiro Yamada [Fri, 5 Dec 2014 15:03:23 +0000 (00:03 +0900)]
ARM: UniPhier: add more device nodes to device tree
Add I2C controller and NAND controller devices. Fix indentation too.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Tom Rini [Mon, 8 Dec 2014 14:36:26 +0000 (09:36 -0500)]
Merge branch 'master' of git://git.denx.de/u-boot-sh
Tom Rini [Thu, 4 Dec 2014 16:27:08 +0000 (11:27 -0500)]
doc/gitmail-rc: Update m68k alias
Signed-off-by: Tom Rini <trini@ti.com>
Peter Kümmel [Sat, 29 Nov 2014 08:26:04 +0000 (17:26 +0900)]
kconfig: Fix warning "‘jump’ may be used uninitialized"
Warning:
In file included from scripts/kconfig/zconf.tab.c:2537:0:
scripts/kconfig/menu.c: In function ‘get_symbol_str’:
scripts/kconfig/menu.c:590:18: warning: ‘jump’ may be used uninitialized in this function [-Wmaybe-uninitialized]
jump->offset = strlen(r->s);
Simplifies the test logic because (head && local) means (jump != 0)
and makes GCC happy when checking if the jump pointer was initialized.
Signed-off-by: Peter Kümmel <syntheticpp@gmx.net>
Signed-off-by: Michal Marek <mmarek@suse.cz>
[ imported from Linux Kernel, commit
2d5603060967 ]
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Masahiro Yamada [Fri, 28 Nov 2014 02:13:28 +0000 (11:13 +0900)]
libfdt: move CONFIG_OF_LIBFDT and CONFIG_FIT to lib/Makefile
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Masahiro Yamada [Fri, 28 Nov 2014 02:13:27 +0000 (11:13 +0900)]
libfdt: descend from lib/ to lib/libfdt/
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Masahiro Yamada [Fri, 28 Nov 2014 02:13:26 +0000 (11:13 +0900)]
lib: bzip2: move bzip2 files to lib/bzip2/ directory
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Suriyan Ramasami [Thu, 27 Nov 2014 21:24:16 +0000 (13:24 -0800)]
fdt: Allow non-FDT kernels to boot when CONFIG_OF_LIBFDT is defined
The boot commands - bootz/bootm mandate a third argument which is the
address to the FDT blob. In cases where this argument is not specified,
boot fails with a message indicating a missing FDT.
This causes non-FDT kernels to fail to boot. This patch allows both FDT
and non-FDT kernels to boot by making the third parameter to the bootm/bootz
optional.
Signed-off-by: Suriyan Ramasami <suriyan.r@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
[trini: Update again for covering appended DTB case after last revert in
this area]
Signed-off-by: Tom Rini <trini@ti.com>
Masahiro Yamada [Wed, 26 Nov 2014 07:02:54 +0000 (16:02 +0900)]
blackfin: include <linux/compiler.h> rather than define __iomem
The macro __iomem is defined in include/linux/compiler.h.
Let's include it rather than double __iomem defines.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Sonic Zhang <sonic.adi@gmail.com>
Masahiro Yamada [Wed, 26 Nov 2014 07:02:53 +0000 (16:02 +0900)]
linux/compat.h: remove redundant macro defines
__user and __iomem are defined in include/linux/compiler.h.
MAX_ERRNO is defined in include/linux/err.h.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Masahiro Yamada [Wed, 26 Nov 2014 07:00:58 +0000 (16:00 +0900)]
Replace <compiler.h> with <linux/compiler.h>
Including <linux/compiler.h> is enough for general use.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Daniel Schwierzeck [Wed, 19 Nov 2014 19:20:11 +0000 (20:20 +0100)]
git-mailrc: fix mips alias
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
angelo@sysam.it [Tue, 25 Nov 2014 09:05:41 +0000 (10:05 +0100)]
Add Alison Wang m68k custodian email/alias
Signed-off-by: Angelo Dureghello <angelo@sysam.it>
angelo@sysam.it [Mon, 24 Nov 2014 14:36:57 +0000 (15:36 +0100)]
Add custodians to the m68k subsystem.
Daniel Schwierzeck [Fri, 21 Nov 2014 22:51:33 +0000 (23:51 +0100)]
Kbuild: introduce Makefile in arch/$ARCH/
Introduce a Makefile under arch/$ARCH/ and include it in the
top Makefile (similar to Linux kernel). This allows further
refactoringi like moving architecture-specific code out of global
makefiles, deprecating config variables (CPU, CPUDIR, SOC) or
deprecating arch/$ARCH/config.mk.
In contrary to Linux kernel, U-Boot defines the ARCH variable by
Kconfig, thus the arch Makefile can only included conditionally
after the top config.mk.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Acked-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Vikas Manocha [Fri, 21 Nov 2014 18:34:23 +0000 (10:34 -0800)]
serial: pl01x: avoid pl01x type check two times
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
Acked-by: Simon Glass <sjg@chromium.org>
Vikas Manocha [Fri, 21 Nov 2014 18:34:22 +0000 (10:34 -0800)]
serial: pl01x: disable as per type of pl01x
pl010 & pl011 have different control register offsets, setting it as per
the pl01x type.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
Acked-by: Simon Glass <sjg@chromium.org>
Vikas Manocha [Fri, 21 Nov 2014 18:34:21 +0000 (10:34 -0800)]
serial: pl01x: move all line control at same place
Receive line control uses same setting as transmit line control, also one lcrh
write is effective for both baud rate & receive line control internal update.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
Acked-by: Simon Glass <sjg@chromium.org>
Vikas Manocha [Fri, 21 Nov 2014 18:34:20 +0000 (10:34 -0800)]
serial: pl01x: fix pl011 baud rate configuration
UART_IBRD, UART_FBRD, and UART_LCR_H form a single 30-bit wide register which
is updated on a single write strobe generated by a UART_LCR_H write. So, to
internally update the content of UART_IBRD or UART_FBRD, a write to UART_LCR_H
must always be performed at the end.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
Acked-by: Simon Glass <sjg@chromium.org>
Vikas Manocha [Fri, 21 Nov 2014 18:34:19 +0000 (10:34 -0800)]
serial: pl01x: pass pl01x_type to set baudrate
Although we were checking the pl01x type, seems like PL010 type was being
passed by mistake.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
Acked-by: Simon Glass <sjg@chromium.org>
Masahiro Yamada [Fri, 21 Nov 2014 02:50:10 +0000 (11:50 +0900)]
imx6: remove redudant CONFIG_SPL_START_S_PATH define
The CPU directory of IMX6 is arch/arm/cpu/armv7, so setting
CONFIG_SPL_START_S_PATH to arch/arm/cpu/armv7 is totally redundant.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Stefano Babic <sbabic@denx.de>
Masahiro Yamada [Fri, 21 Nov 2014 02:50:09 +0000 (11:50 +0900)]
powerpc: a3m071: remove redundant CONFIG_SPL_* defines
The CPU directory of this board is arch/powerpc/cpu/mpc5xxx.
Without the CONFIG_SPL_START_S_PATH and CONFIG_SPL_LDSCRIPT defines,
the same start.o and u-boot-spl.lds are selected by default.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Stefan Roese <sr@denx.de>
Acked-by: Stefan Roese <sr@denx.de>
Masahiro Yamada [Fri, 21 Nov 2014 02:50:08 +0000 (11:50 +0900)]
powerpc: lwmon5: remove redundant CONFIG_SPL_* defines
The CPU directory of this board is arch/powerpc/cpu/ppc4xx.
Without the CONFIG_SPL_START_S_PATH and CONFIG_SPL_LDSCRIPT defines,
the same start.o and u-boot-spl.lds are selected by default.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denk <wd@denx.de>
Acked-by: Stefan Roese <sr@denx.de>
Masahiro Yamada [Fri, 21 Nov 2014 02:26:11 +0000 (11:26 +0900)]
powerpc: mpc8xx: remove hermes board support
This board sprinkles #ifdef(CONFIG_HERMES) over various global files
such as include/common.h, common/board_r.c, common/cmd_bdinfo.c.
Let's zap such an ill-behaved board.
It has not been converted to generic board yet and mpc8xx is old
enough.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denk <wd@denx.de>
Acked-by: Wolfgang Denk <wd@denx.de>
Hector Palacios [Thu, 20 Nov 2014 08:27:42 +0000 (09:27 +0100)]
cmd_fuse: return CMD_RET_FAILURE on error
Fuse drivers, like the mxs_ocotp.c, may return negative error codes but
the commands are only allowed to return CMD_RET_* enum values to the
shell, otherwise the following error appears:
"exit not allowed from main input shell."
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau.dev@gmail.com>
Stephen Warren [Thu, 20 Nov 2014 03:41:04 +0000 (20:41 -0700)]
ARM: rpi: support an environment
Enable ENV_IS_IN_FAT so that the environment can be stored persistently.
It's stored in the FAT partition that the RPi firmware requires. On most
RPis, this is on the SD card (which must be present in order for the
system to boot). On the CM this is on the built-in eMMC device.
Since we now have a persistent environment, there's no need to load
uEnv.txt at boot; we only did that to work around the lack of persistent
environment.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Stephen Warren [Thu, 20 Nov 2014 03:41:03 +0000 (20:41 -0700)]
ARM: rpi: rename rpi_b to rpi
The U-Boot port runs on a variety of RPi models, not just the B. So,
rename the port to something slightly more generic.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Stephen Warren [Wed, 19 Nov 2014 04:40:21 +0000 (21:40 -0700)]
ARM: rpi_b: detect board revision
Detect the board revision early during boot, and print the decoded
model name.
Eventually, this information can be used for tasks such as:
- Allowing/preventing USB device mode; some models have a USB device on-
board so only host mode makes sense. Others connect the SoC directly
to the USB connector, so device-mode might make sense.
- The on-board USB hub/Ethernet requires different GPIOs to enable it,
although luckily the default appears to be fine so far.
- The compute module contains an on-board eMMC device, so we could store
the environment there. Other models use an SD card and so don't support
saving the environment (unless we store it in a file on the FAT boot
partition...)
Set $fdtfile based on this information. At present, the mainline Linux
kernel doesn't contain a separate DTB for most models, but I hope that
will change soon.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Guillaume GARDET [Tue, 18 Nov 2014 09:44:46 +0000 (10:44 +0100)]
spl: if MMCSD_MODE_RAW fails, try MMCSD_MODE_FS, if available
In SPL MMC, boot modes are exclusive. So, if MMCSD_MODE_RAW fails, the board hangs. This patch allows to
try MMCSD_MODE_FS then, if available.
It has been tested on a pandaboard (rev. A3).
Signed-off-by: Guillaume GARDET <guillaume.gardet@free.fr>
Cc: Tom Rini <trini@ti.com>
Heiko Schocher [Tue, 18 Nov 2014 08:08:45 +0000 (09:08 +0100)]
MAINTAINERS: add me as a maintainer of UBI
Add me for UBI custodian.
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Stefan Roese <sr@denx.de>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Wu, Josh [Tue, 18 Nov 2014 05:07:08 +0000 (13:07 +0800)]
net: bootp: as CONFIG_BOOTP_SERVERIP is defined, keep bootfile not changed
Currenly when CONFIG_BOOTP_SERVERIP is defined, the SERVERIP is not changed
when receive the BOOTP packet. But BOOTFILE is changed via BOOTP packet.
As we will load the BOOTFILE from SERVERIP, if the BOOTFILE is modified
by bootp packet but SERVERIP is not, that is not make sense.
This patch make SERVERIP and BOOTFILE be consistent. If we define the
CONFIG_BOOTP_SERVERIP, then SERVERIP and BOOTFILE will not changed by
BOOTP packet. Only IP address is changed.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Daniel Schwierzeck [Sun, 16 Nov 2014 19:30:11 +0000 (20:30 +0100)]
get_maintainer.pl: fix source tree detection
get_maintainer.pl always fails with following message:
./scripts/get_maintainer.pl: The current directory does not appear to be a linux kernel source tree.
This was caused by commit:
commit
548b310c68ac99a0330d8b56c797c09ff0742d1e
Author: Masahiro Yamada <yamada.m@jp.panasonic.com>
Date: Thu Oct 30 15:50:15 2014 +0900
Remove the CREDITS file
This file is not maintained these days.
We use MAINTAINERS for the maintainership of the supported boards.
For dead boards, we have some clues in doc/README.scrapyard and
also imperishable history in git-log.
Remove CREDITS from source tree detection to fix this.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Simon Glass [Fri, 14 Nov 2014 03:51:12 +0000 (20:51 -0700)]
Fix console functions for U-Boot API
Commit 709ea54 made a subtle change to the way the U-Boot API jump table
is set up. So at present putc(), getc(), tstc() and puts() do not work
correctly from functions that use the U-Boot API.
Previously these were set to the stdio functions, but these now take a
parameter specifying which stdio device to use. Instead, we should change
them to use the global functions which do not have a parameter.
This is a slight change in behaviour. The functions will now output to
all selected stdio devices - for example putc() will output a character to
all devices selected by stdout. However in most cases there is only one,
and it isn't necessarily incorrect behaviour anyway.
The API version is not changed since it is compatible with what was there
before.
Reported-by: Martin Dorwig <dorwig@tektronik.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Paul Kocialkowski [Sat, 8 Nov 2014 22:14:56 +0000 (23:14 +0100)]
spl: MMC U-Boot image load from raw partition
Raw images of U-Boot can be stored inside MMC partitions, so it makes sense to
read the partition table, looking for a partition number instead of using
a fixed sector address.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@ti.com>
[trini: Only add mmc_load_image_raw_partition() when
CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION to avoid warning, add missing
conversion in spl_mmc_load_image()]
Signed-off-by: Tom Rini <trini@ti.com>
Mark Tomlinson [Mon, 1 Dec 2014 19:49:19 +0000 (08:49 +1300)]
i2c: Correct spelling error
"diconnect" and "disconnet" should both be "disconnect".
Signed-off-by: Mark Tomlinson <mark.tomlinson@alliedtelesis.co.nz>
Mark Tomlinson [Mon, 1 Dec 2014 19:49:18 +0000 (08:49 +1300)]
i2c: Fix deselection of muxes
Due to an uninitialised variable, when muxes were deselected, any value
could be written to the mux control register. On the PCA9548, this could
result in multiple channels being selected, thus enabling multiple
pull-up resistors, and much bus capacitance.
The fix is simply to initialise the written value to zero.
Signed-off-by: Mark Tomlinson <mark.tomlinson@alliedtelesis.co.nz>
Masahiro Yamada [Fri, 5 Dec 2014 15:03:22 +0000 (00:03 +0900)]
ARM: UniPhier: merge UniPhier config headers into a single file
Some configurations have been moved to Kconfig and the difference
among the config headers of UniPhier SoC variants is getting smaller
and smaller. Now is a good time to merge them into a single file.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Masahiro Yamada [Fri, 5 Dec 2014 15:03:21 +0000 (00:03 +0900)]
ARM: UniPhier: move support card select to Kconfig
There are two kinds of expansion boards which are often used for
the UniPhier platform and they are only exclusively selectable.
It can be better described by the "choice" menu of Kconfig.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Masahiro Yamada [Fri, 5 Dec 2014 15:03:20 +0000 (00:03 +0900)]
ARM: UniPhier: move CONFIG_UNIPHIER_SMP to Kconfig
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Masahiro Yamada [Fri, 5 Dec 2014 15:03:19 +0000 (00:03 +0900)]
ARM: UniPhier: use boot_is_swapped() macro for readability
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Masahiro Yamada [Fri, 5 Dec 2014 15:03:18 +0000 (00:03 +0900)]
ARM: UniPhier: disable autostart by default
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Masahiro Yamada [Fri, 5 Dec 2014 03:20:58 +0000 (12:20 +0900)]
flash: do not fail even if flash_size is zero
CONFIG_SYS_MAX_FLASH_BANKS_DETECT allows to determine the number of
flash banks at run-time, that is, there is a possibility that no flash
bank is found. Even in such cases, it makes sense to continue the
boot process without any flash device.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Stefan Roese <sr@denx.de>