ALSA: hda/hdmi - allow PIN_OUT to be dynamically enabled

(This is upstream 75fae117a5db "ALSA: hda/hdmi - allow PIN_OUT to be
dynamically enabled", backported to stable 3.10 through 3.12. 3.13 and
later can take the original patch.)

Commit 384a48d71520 "ALSA: hda: HDMI: Support codecs with fewer cvts
than pins" dynamically enabled each pin widget's PIN_OUT only when the
pin was actively in use. This was required on certain NVIDIA CODECs for
correct operation. Specifically, if multiple pin widgets each had their
mux input select the same audio converter widget and each pin widget had
PIN_OUT enabled, then only one of the pin widgets would actually receive
the audio, and often not the one the user wanted!

However, this apparently broke some Intel systems, and commit
6169b673618b "ALSA: hda - Always turn on pins for HDMI/DP" reverted the
dynamic setting of PIN_OUT. This in turn broke the afore-mentioned NVIDIA
CODECs.

This change supports either dynamic or static handling of PIN_OUT,
selected by a flag set up during CODEC initialization. This flag is
enabled for all recent NVIDIA GPUs.

Reported-by: Uosis <uosisl@gmail.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ALSA: hda - hdmi: introduce patch_nvhdmi()

(This is a backport of *part* of upstream 611885bc963a "ALSA: hda -
hdmi: Disallow unsupported 2ch remapping on NVIDIA codecs" to stable
3.10 through 3.12. Later stable already contain all of the original
patch.)

Mainline commit 611885bc963a "ALSA: hda - hdmi: Disallow unsupported 2ch
remapping on NVIDIA codecs" introduces function patch_nvhdmi(). That
function is edited by 75fae117a5db "ALSA: hda/hdmi - allow PIN_OUT to be
dynamically enabled". In order to backport the PIN_OUT patch, I am first
back-porting just the addition of function patch_nvhdmi(), so that the
conflicts applying the PIN_OUT patch are simplified.

Ideally, one might backport all of 611885bc963a. However, that commit
doesn't apply to stable kernels, since it relies on a chain of other
patches which implement new features.

Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
[swarren, extracted just a small part of the original patch]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

KVM: PPC: e500: Fix bad address type in deliver_tlb_misss()

commit 70713fe315ed14cd1bb07d1a7f33e973d136ae3d upstream.

Use gva_t instead of unsigned int for eaddr in deliver_tlb_miss().

Signed-off-by: Mihai Caraman <mihai.caraman@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

KVM: PPC: Book3S HV: use xics_wake_cpu only when defined

commit 48eaef0518a565d3852e301c860e1af6a6db5a84 upstream.

Signed-off-by: Andreas Schwab <schwab@linux-m68k.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

parisc: fix cache-flushing

commit 57737c49dd72c96cfbcd4f66559f3ffc399aeb4f upstream.

This commit:
f8dae00684d678afa13041ef170cecfd1297ed40: parisc: Ensure full cache coherency for kmap/kunmap
caused negative caching side-effects, e.g. hanging processes with expect and
too many inequivalent alias messages from flush_dcache_page() on Debian 5 systems.

This patch now partly reverts it and has been in production use on our debian buildd
makeservers since a week without any major problems.

Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iwlwifi: pcie: enable oscillator for L1 exit

commit 2d93aee152b1758a94a18fe15d72153ba73b5679 upstream.

Enabling the oscillator consumes slightly more power (100uA)
but allows to make sure that we exit from L1 on time.

Not doing so might lead to a PCIe specification violation
since we might wake up from L1 at the wrong time.
This issue has been identified on 3160 and 7260 only.
On older NICs L1 off is not enabled, on newer NICs (7265),
the issue is fixed.

When the bug occurs the user sees that the NIC has
disappeared from the PCI bridge, any access to the device
returns 0xff.

This fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=64541

and has been extensively discussed here:
http://markmail.org/thread/mfmpzqt3r333n4bo

Fixes: 99cd47142399 ("iwlwifi: add 7000 series device configuration")
Reported-and-tested-by: wzyboy <wzyboy@wzyboy.org>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ip6tnl: fix double free of fb_tnl_dev on exit

[ No relevant upstream commit. ]

This problem was fixed upstream by commit 1e9f3d6f1c40 ("ip6tnl: fix use after
free of fb_tnl_dev").
The upstream patch depends on upstream commit 0bd8762824e7 ("ip6tnl: add x-netns
support"), which was not backported into 3.10 branch.

First, explain the problem: when the ip6_tunnel module is unloaded,
ip6_tunnel_cleanup() is called.
rmmod ip6_tunnel
=> ip6_tunnel_cleanup()
  => rtnl_link_unregister()
    => __rtnl_kill_links()
      => for_each_netdev(net, dev) {
        if (dev->rtnl_link_ops == ops)
         ops->dellink(dev, &list_kill);
        }
At this point, the FB device is deleted (and all ip6tnl tunnels).
  => unregister_pernet_device()
    => unregister_pernet_operations()
      => ops_exit_list()
        => ip6_tnl_exit_net()
          => ip6_tnl_destroy_tunnels()
            => t = rtnl_dereference(ip6n->tnls_wc[0]);
               unregister_netdevice_queue(t->dev, &list);
We delete the FB device a second time here!

The previous fix removes these lines, which fix this double free. But the patch
introduces a memory leak when a netns is destroyed, because the FB device is
never deleted. By adding an rtnl ops which delete all ip6tnl device excepting
the FB device, we can keep this exlicit removal in ip6_tnl_destroy_tunnels().

CC: Steven Rostedt <rostedt@goodmis.org>
CC: Willem de Bruijn <willemb@google.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Reported-by: Steven Rostedt <srostedt@redhat.com>
Tested-by: Steven Rostedt <srostedt@redhat.com> (and our entire MRG team)
Tested-by: "Luis Claudio R. Goncalves" <lgoncalv@redhat.com>
Tested-by: John Kacur <jkacur@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Revert "ip6tnl: fix use after free of fb_tnl_dev"

[ No relevant upstream commit. ]

This reverts commit 22c3ec552c29cf4bd4a75566088950fe57d860c4.

This patch is not the right fix, it introduces a memory leak when a netns is
destroyed (the FB device is never deleted).

Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Reported-by: Steven Rostedt <srostedt@redhat.com>
Tested-by: Steven Rostedt <srostedt@redhat.com> (and our entire MRG team)
Tested-by: "Luis Claudio R. Goncalves" <lgoncalv@redhat.com>
Tested-by: John Kacur <jkacur@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

sit: fix double free of fb_tunnel_dev on exit

[ No relevant upstream commit. ]

This problem was fixed upstream by commit 9434266f2c64 ("sit: fix use after free
of fb_tunnel_dev").
The upstream patch depends on upstream commit 5e6700b3bf98 ("sit: add support of
x-netns"), which was not backported into 3.10 branch.

First, explain the problem: when the sit module is unloaded, sit_cleanup() is
called.
rmmod sit
=> sit_cleanup()
  => rtnl_link_unregister()
    => __rtnl_kill_links()
      => for_each_netdev(net, dev) {
        if (dev->rtnl_link_ops == ops)
         ops->dellink(dev, &list_kill);
        }
At this point, the FB device is deleted (and all sit tunnels).
  => unregister_pernet_device()
    => unregister_pernet_operations()
      => ops_exit_list()
        => sit_exit_net()
          => sit_destroy_tunnels()
          In this function, no tunnel is found.
          => unregister_netdevice_queue(sitn->fb_tunnel_dev, &list);
We delete the FB device a second time here!

Because we cannot simply remove the second deletion (sit_exit_net() must remove
the FB device when a netns is deleted), we add an rtnl ops which delete all sit
device excepting the FB device and thus we can keep the explicit deletion in
sit_exit_net().

CC: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Reported-by: Steven Rostedt <srostedt@redhat.com>
Tested-by: Steven Rostedt <srostedt@redhat.com> (and our entire MRG team)
Tested-by: "Luis Claudio R. Goncalves" <lgoncalv@redhat.com>
Tested-by: John Kacur <jkacur@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

xen-netfront: fix resource leak in netfront

[ Upstream commit cefe0078eea52af17411eb1248946a94afb84ca5 ]

This patch removes grant transfer releasing code from netfront, and uses
gnttab_end_foreign_access to end grant access since
gnttab_end_foreign_access_ref may fail when the grant entry is
currently used for reading or writing.

* clean up grant transfer code kept from old netfront(2.6.18) which grants
pages for access/map and transfer. But grant transfer is deprecated in current
netfront, so remove corresponding release code for transfer.

* fix resource leak, release grant access (through gnttab_end_foreign_access)
and skb for tx/rx path, use get_page to ensure page is released when grant
access is completed successfully.

Xen-blkfront/xen-tpmfront/xen-pcifront also have similar issue, but patches
for them will be created separately.

V6: Correct subject line and commit message.

V5: Remove unecessary change in xennet_end_access.

V4: Revert put_page in gnttab_end_foreign_access, and keep netfront change in
single patch.

V3: Changes as suggestion from David Vrabel, ensure pages are not freed untill
grant acess is ended.

V2: Improve patch comments.

Signed-off-by: Annie Li <annie.li@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: Fix memory leak if TPROXY used with TCP early demux

[ Upstream commit a452ce345d63ddf92cd101e4196569f8718ad319 ]

I see a memory leak when using a transparent HTTP proxy using TPROXY
together with TCP early demux and Kernel v3.8.13.15 (Ubuntu stable):

unreferenced object 0xffff88008cba4a40 (size 1696):
  comm "softirq", pid 0, jiffies 4294944115 (age 8907.520s)
  hex dump (first 32 bytes):
    0a e0 20 6a 40 04 1b 37 92 be 32 e2 e8 b4 00 00  .. j@..7..2.....
    02 00 07 01 00 00 00 00 00 00 00 00 00 00 00 00  ................
  backtrace:
    [<ffffffff810b710a>] kmem_cache_alloc+0xad/0xb9
    [<ffffffff81270185>] sk_prot_alloc+0x29/0xc5
    [<ffffffff812702cf>] sk_clone_lock+0x14/0x283
    [<ffffffff812aaf3a>] inet_csk_clone_lock+0xf/0x7b
    [<ffffffff8129a893>] netlink_broadcast+0x14/0x16
    [<ffffffff812c1573>] tcp_create_openreq_child+0x1b/0x4c3
    [<ffffffff812c033e>] tcp_v4_syn_recv_sock+0x38/0x25d
    [<ffffffff812c13e4>] tcp_check_req+0x25c/0x3d0
    [<ffffffff812bf87a>] tcp_v4_do_rcv+0x287/0x40e
    [<ffffffff812a08a7>] ip_route_input_noref+0x843/0xa55
    [<ffffffff812bfeca>] tcp_v4_rcv+0x4c9/0x725
    [<ffffffff812a26f4>] ip_local_deliver_finish+0xe9/0x154
    [<ffffffff8127a927>] __netif_receive_skb+0x4b2/0x514
    [<ffffffff8127aa77>] process_backlog+0xee/0x1c5
    [<ffffffff8127c949>] net_rx_action+0xa7/0x200
    [<ffffffff81209d86>] add_interrupt_randomness+0x39/0x157

But there are many more, resulting in the machine going OOM after some
days.

From looking at the TPROXY code, and with help from Florian, I see
that the memory leak is introduced in tcp_v4_early_demux():

  void tcp_v4_early_demux(struct sk_buff *skb)
  {
    /* ... */

    iph = ip_hdr(skb);
    th = tcp_hdr(skb);

    if (th->doff < sizeof(struct tcphdr) / 4)
        return;

    sk = __inet_lookup_established(dev_net(skb->dev), &tcp_hashinfo,
                       iph->saddr, th->source,
                       iph->daddr, ntohs(th->dest),
                       skb->skb_iif);
    if (sk) {
        skb->sk = sk;

where the socket is assigned unconditionally to skb->sk, also bumping
the refcnt on it.  This is problematic, because in our case the skb
has already a socket assigned in the TPROXY target.  This then results
in the leak I see.

The very same issue seems to be with IPv6, but haven't tested.

Reviewed-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Holger Eitzenberger <holger@eitzenberger.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

fib_frontend: fix possible NULL pointer dereference

[ Upstream commit a0065f266a9b5d51575535a25c15ccbeed9a9966 ]

The two commits 0115e8e30d (net: remove delay at device dismantle) and
748e2d9396a (net: reinstate rtnl in call_netdevice_notifiers()) silently
removed a NULL pointer check for in_dev since Linux 3.7.

This patch re-introduces this check as it causes crashing the kernel when
setting small mtu values on non-ip capable netdevices.

Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ip_tunnel: clear IPCB in ip_tunnel_xmit() in case dst_link_failure() is called

[ Upstream commit 11c21a307d79ea5f6b6fc0d3dfdeda271e5e65f6 ]

commit a622260254ee48("ip_tunnel: fix kernel panic with icmp_dest_unreach")
clear IPCB in ip_tunnel_xmit()  , or else skb->cb[] may contain garbage from
GSO segmentation layer.

But commit 0e6fbc5b6c621("ip_tunnels: extend iptunnel_xmit()") refactor codes,
and it clear IPCB behind the dst_link_failure().

So clear IPCB in ip_tunnel_xmit() just like commti a622260254ee48("ip_tunnel:
fix kernel panic with icmp_dest_unreach").

Signed-off-by: Duan Jiong <duanj.fnst@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

s390/bpf,jit: fix 32 bit divisions, use unsigned divide instructions

[ Upstream commit 3af57f78c38131b7a66e2b01e06fdacae01992a3 ]

The s390 bpf jit compiler emits the signed divide instructions "dr" and "d"
for unsigned divisions.
This can cause problems: the dividend will be zero extended to a 64 bit value
and the divisor is the 32 bit signed value as specified A or X accumulator,
even though A and X are supposed to be treated as unsigned values.

The divide instrunctions will generate an exception if the result cannot be
expressed with a 32 bit signed value.
This is the case if e.g. the dividend is 0xffffffff and the divisor either 1
or also 0xffffffff (signed: -1).

To avoid all these issues simply use unsigned divide instructions.

Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

bpf: do not use reciprocal divide

[ Upstream commit aee636c4809fa54848ff07a899b326eb1f9987a2 ]

At first Jakub Zawadzki noticed that some divisions by reciprocal_divide
were not correct. (off by one in some cases)
http://www.wireshark.org/~darkjames/reciprocal-buggy.c

He could also show this with BPF:
http://www.wireshark.org/~darkjames/set-and-dump-filter-k-bug.c

The reciprocal divide in linux kernel is not generic enough,
lets remove its use in BPF, as it is not worth the pain with
current cpus.

Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Jakub Zawadzki <darkjames-ws@darkjames.pl>
Cc: Mircea Gherzan <mgherzan@gmail.com>
Cc: Daniel Borkmann <dxchgb@gmail.com>
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Cc: Matt Evans <matt@ozlabs.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tcp: metrics: Avoid duplicate entries with the same destination-IP

[ Upstream commit 77f99ad16a07aa062c2d30fae57b1fee456f6ef6 ]

Because the tcp-metrics is an RCU-list, it may be that two
soft-interrupts are inside __tcp_get_metrics() for the same
destination-IP at the same time. If this destination-IP is not yet part of
the tcp-metrics, both soft-interrupts will end up in tcpm_new and create
a new entry for this IP.
So, we will have two tcp-metrics with the same destination-IP in the list.

This patch checks twice __tcp_get_metrics(). First without holding the
lock, then while holding the lock. The second one is there to confirm
that the entry has not been added by another soft-irq while waiting for
the spin-lock.

Fixes: 51c5d0c4b169b (tcp: Maintain dynamic metrics in local cache.)
Signed-off-by: Christoph Paasch <christoph.paasch@uclouvain.be>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: rds: fix per-cpu helper usage

[ Upstream commit c196403b79aa241c3fefb3ee5bb328aa7c5cc860 ]

commit ae4b46e9d "net: rds: use this_cpu_* per-cpu helper" broke per-cpu
handling for rds. chpfirst is the result of __this_cpu_read(), so it is
an absolute pointer and not __percpu. Therefore, __this_cpu_write()
should not operate on chpfirst, but rather on cache->percpu->first, just
like __this_cpu_read() did before.

Signed-off-byd Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net,via-rhine: Fix tx_timeout handling

[ Upstream commit a926592f5e4e900f3fa903298c4619a131e60963 ]

rhine_reset_task() misses to disable the tx scheduler upon reset,
this can lead to a crash if work is still scheduled while we're resetting
the tx queue.

Fixes:
[   93.591707] BUG: unable to handle kernel NULL pointer dereference at 0000004c
[   93.595514] IP: [<c119d10d>] rhine_napipoll+0x491/0x6

Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: avoid reference counter overflows on fib_rules in multicast forwarding

[ Upstream commit 95f4a45de1a0f172b35451fc52283290adb21f6e ]

Bob Falken reported that after 4G packets, multicast forwarding stopped
working. This was because of a rule reference counter overflow which
freed the rule as soon as the overflow happend.

This patch solves this by adding the FIB_LOOKUP_NOREF flag to
fib_rules_lookup calls. This is safe even from non-rcu locked sections
as in this case the flag only implies not taking a reference to the rule,
which we don't need at all.

Rules only hold references to the namespace, which are guaranteed to be
available during the call of the non-rcu protected function reg_vif_xmit
because of the interface reference which itself holds a reference to
the net namespace.

Fixes: f0ad0860d01e47 ("ipv4: ipmr: support multiple tables")
Fixes: d1db275dd3f6e4 ("ipv6: ip6mr: support multiple tables")
Reported-by: Bob Falken <NetFestivalHaveFun@gmx.com>
Cc: Patrick McHardy <kaber@trash.net>
Cc: Thomas Graf <tgraf@suug.ch>
Cc: Julian Anastasov <ja@ssi.bg>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ieee802154: Fix memory leak in ieee802154_add_iface()

[ Upstream commit 267d29a69c6af39445f36102a832b25ed483f299 ]

Fix a memory leak in the ieee802154_add_iface() error handling path.
Detected by Coverity: CID 710490.

Signed-off-by: Christian Engelmayer <cengelma@gmx.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

inet_diag: fix inet_diag_dump_icsk() timewait socket state logic

[ Based upon upstream commit 70315d22d3c7383f9a508d0aab21e2eb35b2303a ]

Fix inet_diag_dump_icsk() to reflect the fact that both TIME_WAIT and
FIN_WAIT2 connections are represented by inet_timewait_sock (not just
TIME_WAIT). Thus:

(a) We need to iterate through the time_wait buckets if the user wants
either TIME_WAIT or FIN_WAIT2. (Before fixing this, "ss -nemoi state
fin-wait-2" would not return any sockets, even if there were some in
FIN_WAIT2.)

(b) We need to check tw_substate to see if the user wants to dump
sockets in the particular substate (TIME_WAIT or FIN_WAIT2) that a
given connection is in. (Before fixing this, "ss -nemoi state
time-wait" would actually return sockets in state FIN_WAIT2.)

An analogous fix is in v3.13: 70315d22d3c7383f9a508d0aab21e2eb35b2303a
("inet_diag: fix inet_diag_dump_icsk() to use correct state for
timewait sockets") but that patch is quite different because 3.13 code
is very different in this area due to the unification of TCP hash
tables in 05dbc7b ("tcp/dccp: remove twchain") in v3.13-rc1.

I tested that this applies cleanly between v3.3 and v3.12, and tested
that it works in both 3.3 and 3.12. It does not apply cleanly to 3.2
and earlier (though it makes semantic sense), and semantically is not
the right fix for 3.13 and beyond (as mentioned above).

Signed-off-by: Neal Cardwell <ncardwell@google.com>
Cc: Eric Dumazet <edumazet@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

bnx2x: fix DMA unmapping of TSO split BDs

[ Upstream commit 95e92fd40c967c363ad66b2fd1ce4dcd68132e54 ]

bnx2x triggers warnings with CONFIG_DMA_API_DEBUG=y:

  WARNING: CPU: 0 PID: 2253 at lib/dma-debug.c:887 check_unmap+0xf8/0x920()
  bnx2x 0000:28:00.0: DMA-API: device driver frees DMA memory with
  different size [device address=0x00000000da2b389e] [map size=1490 bytes]
  [unmap size=66 bytes]

The reason is that bnx2x splits a TSO BD into two BDs (headers + data)
using one DMA mapping for both, but it uses only the length of the first
BD when unmapping.

This patch fixes the bug by unmapping the whole length of the two BDs.

Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Acked-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

hp_accel: Add a new PnP ID HPQ6007 for new HP laptops

commit b0ad4ff35d479a46a3b995a299db9aeb097acfce upstream.

The DriveGuard chips on the new HP laptops are with a new PnP ID
"HPQ6007".  It should be compatible with older chips.

Acked-by: Éric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Matthew Garrett <matthew.garrett@nebula.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

bcache: Data corruption fix

commit ef71ec00002d92a08eb27e9d036e3d48835b6597 upstream.

The code that handles overlapping extents that we've just read back in from disk
was depending on the behaviour of the code that handles overlapping extents as
we're inserting into a btree node in the case of an insert that forced an
existing extent to be split: on insert, if we had to split we'd also insert a
new extent to represent the top part of the old extent - and then that new
extent would get written out.

The code that read the extents back in thus not bother with splitting extents -
if it saw an extent that ovelapped in the middle of an older extent, it would
trim the old extent to only represent the bottom part, assuming that the
original insert would've inserted a new extent to represent the top part.

I still haven't figured out _how_ it can happen, but I'm now pretty convinced
(and testing has confirmed) that there's some kind of an obscure corner case
(probably involving extent merging, and multiple overwrites in different sets)
that breaks this. The fix is to change the mergesort fixup code to split extents
itself when required.

Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

vfs: Is mounted should be testing mnt_ns for NULL or error.

commit 260a459d2e39761fbd39803497205ce1690bc7b1 upstream.

A bug was introduced with the is_mounted helper function in
commit f7a99c5b7c8bd3d3f533c8b38274e33f3da9096e
Author: Al Viro <viro@zeniv.linux.org.uk>
Date:   Sat Jun 9 00:59:08 2012 -0400

    get rid of ->mnt_longterm

    it's enough to set ->mnt_ns of internal vfsmounts to something
    distinct from all struct mnt_namespace out there; then we can
    just use the check for ->mnt_ns != NULL in the fast path of
    mntput_no_expire()

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
The intent was to test if the real_mount(vfsmount)->mnt_ns was
NULL_OR_ERR but the code is actually testing real_mount(vfsmount)
and always returning true.

The result is d_absolute_path returning paths it should be hiding.

Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ext4: avoid clearing beyond i_blocks when truncating an inline data file

commit 09c455aaa8f47a94d5bafaa23d58365768210507 upstream.

A missing cast means that when we are truncating a file which is less
than 60 bytes, we don't clear the correct area of memory, and in fact
we can end up truncating the next inode in the inode table, or worse
yet, some other kernel data structure.

Addresses-Coverity-Id: #751987

Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

libata: disable LPM for some WD SATA-I devices

commit ecd75ad514d73efc1bbcc5f10a13566c3ace5f53 upstream.

For some reason, some early WD drives spin up and down drives
erratically when the link is put into slumber mode which can reduce
the life expectancy of the device significantly.  Unfortunately, we
don't have full list of devices and given the nature of the issue it'd
be better to err on the side of false positives than the other way
around.  Let's disable LPM on all WD devices which match one of the
known problematic model prefixes and are SATA-I.

As horkage list doesn't support matching SATA capabilities, this is
implemented as two horkages - WD_BROKEN_LPM and NOLPM.  The former is
set for the known prefixes and sets the latter if the matched device
is SATA-I.

Note that this isn't optimal as this disables all LPM operations and
partial link power state reportedly works fine on these; however, the
way LPM is implemented in libata makes it difficult to precisely map
libata LPM setting to specific link power state.  Well, these devices
are already fairly outdated.  Let's just disable whole LPM for now.

Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-and-tested-by: Nikos Barkas <levelwol@gmail.com>
Reported-and-tested-by: Ioannis Barkas <risc4all@yahoo.com>
References: https://bugzilla.kernel.org/show_bug.cgi?id=57211
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ata: sata_mv: fix disk hotplug for Armada 370/XP SoCs

commit 9013d64e661fc2a37a1742670202171c27fef4b5 upstream.

On Armada 370/XP SoCs, once a disk is removed from a SATA port, then the
re-plug events are not detected by the sata_mv driver. This patch fixes
the issue by updating the PHY speed in the LP_PHY_CTL register (0x58)
according to the SControl speed.

Note that this fix is only applied if the compatible string
"marvell,armada-370-sata" is found in the SATA DT node.

Fixes: 9ae6f740b49f ("arm: mach-mvebu: add support for Armada 370 and Armada XP with DT")
Signed-off-by: Lior Amsalem <alior@marvell.com>
Signed-off-by: Nadav Haklai <nadavh@marvell.com>
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Gregory Clement <gregory.clement@free-electrons.com>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ata: sata_mv: introduce compatible string "marvell, armada-370-sata"

commit b1f5c73bd5a4752efb7d7af019034044b08aafe9 upstream.

The sata_mv driver supports the SATA IP found in several Marvell SoCs.
As some new SATA registers have been introduced with the Armada 370/XP
SoCs, a way to identify them is needed.

This patch introduces a new compatible string for the SATA IP found in
Armada 370/XP SoCs.

Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Gregory Clement <gregory.clement@free-electrons.com>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Cc: Lior Amsalem <alior@marvell.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tpm/tpm_ppi: Do not compare strcmp(a,b) == -1

commit 747d35bd9bb4ae6bd74b19baa5bbe32f3e0cee11 upstream.

Depending on the implementation strcmp might return the difference between
two strings not only -1,0,1 consequently
 if (strcmp (a,b) == -1)
might lead to taking the wrong branch

-> compare with < 0  instead,
which in any case is more canonical.

Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tpm/tpm_i2c_stm_st33: Check return code of get_burstcount

commit 85c5e0d451125c6ddb78663972e40af810b83644 upstream.

The 'get_burstcount' function can in some circumstances 'return -EBUSY' which
in tpm_stm_i2c_send is stored in an 'u32 burstcnt'
thus converting the signed value into an unsigned value, resulting
in 'burstcnt' being huge.
Changing the type to u32 only does not solve the problem as the signed
value is converted to an unsigned in I2C_WRITE_DATA, resulting in the
same effect.

Thus
-> Change type of burstcnt to u32 (the return type of get_burstcount)
-> Add a check for the return value of 'get_burstcount' and propagate a
potential error.

This makes also sense in the 'I2C_READ_DATA' case, where the there is no
signed/unsigned conversion.

found by coverity
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ALSA: hda - Fix silent output on MacBook Air 1,1

commit e7729a415315fcd9516912050d85d5aaebcededc upstream.

Similarly to other Apple products, MBA 1,1 needs a specific quirk.
Pin 0x18 must be set to VREF_50 to have sound output.  This was no
longer done since commit 1a97b7f, resulting in a mute built-in speaker.

This patch corrects the regression by creating a fixup for the MBA 1,1.

Fixes: 1a97b7f22774 ("ALSA: hda/realtek - Remove the last static quirks for ALC882")
Tested-by: Adrien Vergé <adrienverge@gmail.com>
Signed-off-by: Adrien Vergé <adrienverge@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ALSA: Enable CONFIG_ZONE_DMA for smaller PCI DMA masks

commit 80ab8eae70e51d578ebbeb228e0f7a562471b8b7 upstream.

The PCI devices with DMA masks smaller than 32bit should enable
CONFIG_ZONE_DMA.  Since the recent change of page allocator, page
allocations via dma_alloc_coherent() with the limited DMA mask bits
may fail more frequently, ended up with no available buffers, when
CONFIG_ZONE_DMA isn't enabled.  With CONFIG_ZONE_DMA, the system has
much more chance to obtain such pages.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=68221
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ALSA: hda - Don't create duplicated ctls for loopback paths

commit 43a8e50a46a4e1dd1451e4a4ffa1f7695fb7d287 upstream.

AD1986A mic pins (0x1d and 0x1f) share the same widget for controlling
the loopback volume/mute, but the generic parser didn't check it.
This ended up with the duplicated controls for the same effect.

This patch adds the check of the duplication for avoiding it.

After this fix, there will be only one control although it affects
both paths; this remaining issue should be fixed later in a different
patch.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=66621
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ALSA: rme9652: fix a missing comma in channel_map_9636_ds[]

commit 770bd4bf2e664939a9dacd3d26ec9ff7a3933210 upstream.

The lack of comma leads to the wrong channel for an SPDIF channel.
Unfortunately this wasn't caught by compiler because it's still a
valid expression.

Reported-by: Alexander Aristov <aristov.alexander@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ASoC: wm5110: Extend SYSCLK patch file for rev D

commit 34354792432b6e0a3b156819a1a19716c50d3473 upstream.

Latest evaluation of the the device has given some patch file additions
for improved performance.

Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ASoC: adau1701: Fix ADAU1701_SEROCTL_WORD_LEN_16 constant

commit e20970ada3f699c113fe64b04492af083d11a7d8 upstream.

The driver defines ADAU1701_SEROCTL_WORD_LEN_16 as 0x10 while it should be b10,
so 0x2. This patch fixes it.

Reported-by: Magnus Reftel <magnus.reftel@lockless.no>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mfd: max77686: Fix regmap resource leak on driver remove

commit 74142ffc0b52cfe6f9d2f6f34a5f3eedbfe3ce51 upstream.

The regmap used by max77686 MFD driver was not freed with regmap_exit()
on driver exit. This lead to leak of resources.

Replace regmap_init_i2c() call in driver probe with initialization of
managed register map so the regmap will be properly freed by the device
management code.

Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

perf kvm: Fix kvm report without guestmount.

commit ad85ace07a05062ef6b59c35a5e80b6eaee1eee6 upstream.

Currently, if we use perf kvm --guestkallsyms --guestmodules report, we
can not get the perf information from perf data file. All sample are
shown as unknown.

Reproducing steps:
# perf kvm --guestkallsyms /tmp/kallsyms --guestmodules /tmp/modules record -a sleep 1
[ perf record: Woken up 1 times to write data ]
[ perf record: Captured and wrote 0.624 MB perf.data.guest (~27260 samples) ]
# perf kvm --guestkallsyms /tmp/kallsyms --guestmodules /tmp/modules report |grep %
   100.00%  [guest/6471]  [unknown]         [g] 0xffffffff8164f330

This bug was introduced by 207b57926 (perf kvm: Fix regression with guest machine creation).
In original code, it uses perf_session__find_machine(), it means we deliver symbol to machine
which has the same pid, if no machine found, deliver it to *default* guest. But if we use
perf_session__findnew_machine() here, if no machine was found, new machine with pid will be built
and added. Then the default guest which with pid == 0 will never get a symbol.

And because the new machine initialized here has no kernel map created, the symbol delivered to
it will be marked as "unknown".

This patch here is to revert commit 207b57926 and fix the SEGFAULT bug in another way.

Verification steps:
# ./perf kvm --guestkallsyms /home/kallsyms --guestmodules /home/modules record -a sleep 1
[ perf record: Woken up 1 times to write data ]
[ perf record: Captured and wrote 0.651 MB perf.data.guest (~28437 samples) ]
# ./perf kvm --guestkallsyms /home/kallsyms --guestmodules /home/modules report |grep %
    22.64%    :6471  [guest.kernel.kallsyms]  [g] update_rq_clock.part.70
    19.99%    :6471  [guest.kernel.kallsyms]  [g] d_free
    18.46%    :6471  [guest.kernel.kallsyms]  [g] bio_phys_segments
    16.25%    :6471  [guest.kernel.kallsyms]  [g] dequeue_task
    12.78%    :6471  [guest.kernel.kallsyms]  [g] __switch_to
     7.91%    :6471  [guest.kernel.kallsyms]  [g] scheduler_tick
     1.75%    :6471  [guest.kernel.kallsyms]  [g] native_apic_mem_write
     0.21%    :6471  [guest.kernel.kallsyms]  [g] apic_timer_interrupt

Signed-off-by: Dongsheng Yang <yangds.fnst@cn.fujitsu.com>
Acked-by: David Ahern <dsahern@gmail.com>
Cc: David Ahern <dsahern@gmail.com>
Link: http://lkml.kernel.org/r/1387564907-3045-1-git-send-email-yangds.fnst@cn.fujitsu.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

pinctrl: sunxi: Honor GPIO output initial vaules

commit fa8cf57c923e86a693a85aff1df579245a27cbb3 upstream.

Some GPIO users, such as fixed-regulator, request GPIO output with
initial value of 1. This was ignored by sunxi driver.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

rtc: max8907: weekday encoding fixes

commit 75ea799df4cb07e505c91b4abaa87bc28aad3e66 upstream.

The current MAX8907 driver has two issues related to weekday value
handling:

1)

The HW WEEKDAY register has range 0..6 rather than 1..7 as documented.
Note that I validated the actual HW range by observing the HW register
roll from 6->0 rather than 6->7->1 as would otherwise be expected.

This matches Linux's tm_wday range of 0..6.

When the CMOS RAM content is lost, the date returned from the device is
2007-01-01 00:00:00, which is a Monday.  The WEEKDAY register reads 1 in
this case.  This matches the numbering in Linux's tm_wday field.

Hence we should write Linux's tm_wday value to the register without
modifying it.  Hence, remove the +1/-1 calculations for WEEKDAY/tm_wday.

2)

There's no need to make alarms match on the WEEKDAY register, since the
other fields together uniquely define the alarm date/time.  Ignoring the
WEEKDAY value in the match isolates the driver from any incorrect value in
the current time copy of the WEEKDAY register.

Each change individually, or both together, solves an issue that I
observed; "hwclock -r" would time out waiting for its alarm to fire if the
CMOS RAM content had been lost, and hence the WEEKDAY register value
mismatched what the driver expected it to be.  "hwclock -w" would solve
this by over-writing the HW default WEEKDAY register value with what the
driver expected.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

parport: parport_pc: remove double PCI ID for NetMos

commit d6a484520c5572a4170fa915109ccfc0c38f5008 upstream.

In commit 85747f ("PATCH] parport: add NetMOS 9805 support") Max added
the PCI ID for NetMOS 9805 based on a Debian bug report from 2k4 which
was at the v2.4.26 time frame. The patch made into 2.6.14.
Shortly before that patch akpm merged commit 296d3c783b ("[PATCH] Support
NetMOS based PCI cards providing serial and parallel ports") which made
into v2.6.9-rc1.
Now we have two different entries for the same PCI id.
I have here the NetMos 9805 which claims to support SPP/EPP/ECP mode.
This patch takes Max's entry for titan_1284p1 (base != -1 specifies the
ioport for ECP mode) and replaces akpm's entry for netmos_9805 which
specified -1 (=none). Both share the same PCI-ID (my card has subsystem
0x1000 / 0x0020 so it should match PCI_ANY).

While here I also drop the entry for titan_1284p2 which is the same as
netmos_9815.

Cc: Maximilian Attems <maks@stro.at>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

s390/uapi: fix struct statfs64 definition

commit 4e078146dff728f4865270a47710d57797e81eb6 upstream.

With b8668fd0a7e1b59f "s390/uapi: change struct statfs[64] member types
to unsigned values" the size of a couple of struct statfs64 member got
incorrectly changed from 64 to 32 bit for 32 bit builds.

Fix this by changing the type of couple of struct statfs64 members from
unsigned long to unsigned long long.
The definition of struct compat_statfs64 was correct however.

Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

KVM: s390: fix diagnose code extraction

commit 743db27c526e0f31cc507959d662e97e2048a86f upstream.

The diagnose code to be used is the contents of the base register (if not
zero), plus the displacement. The current code ignores the base register
contents. So let's fix that...

Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Cc: stable@vger.kernel.org
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

serial: 8250: enable UART_BUG_NOMSR for Tegra

commit 3685f19e07802ec4207b52465c408f185b66490e upstream.

Tegra chips have 4 or 5 identical UART modules embedded. UARTs C..E have
their MODEM-control signals tied off to a static state. However UARTs A
and B can optionally route those signals to/from package pins, depending
on the exact pinmux configuration.

When these signals are not routed to package pins, false interrupts may
trigger either temporarily, or permanently, all while not showing up in
the IIR; it will read as NO_INT. This will eventually lead to the UART
IRQ being disabled due to unhandled interrupts. When this happens, the
kernel may print e.g.:

    irq 68: nobody cared (try booting with the "irqpoll" option)

In order to prevent this, enable UART_BUG_NOMSR. This prevents
UART_IER_MSI from being enabled, which prevents the false interrupts
from triggering.

In practice, this is not needed under any of the following conditions:

* On Tegra chips after Tegra30, since the HW bug has apparently been
  fixed.

* On UARTs C..E since their MODEM control signals are tied to the correct
  static state which doesn't trigger the issue.

* On UARTs A..B if the MODEM control signals are routed out to package
  pins, since they will then carry valid signals.

However, we ignore these exceptions for now, since they are only relevant
if a board actually hooks up more than a 4-wire UART, and no currently
supported board does this. If we ever support a board that does, we can
refine the algorithm that enables UART_BUG_NOMSR to take those exceptions
into account, and/or read a flag from DT/... that indicates that the
board has hooked up and pinmux'd more than a 4-wire UART.

Reported-by: Olof Johansson <olof@lixom.net> # autotester
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

serial: 8250: Fix initialisation of Quatech cards with the AMCC PCI chip

commit 9c5320f8d7d9a2cf623e65d50e1113f34d9b9eb1 upstream.

Fix the initialisation of older Quatech serial cards which are fitted with
the AMCC PCI Matchmaker interface chip.

Signed-off-by: Jonathan Woithe (jwoithe@just42.net)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

serial: add support for 200 v3 series Titan card

commit 48c0247d7b7bf58abb85a39021099529df365c4d upstream.

Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

hwmon: (k10temp) Add support for Kaveri CPUs

commit d303b1b5fbb688282bbf72a534b9dfed7af9fe4f upstream.

Add new PCI ID to support new model "Kaveri" family.

Signed-off-by: Philip Pokorny <ppokorny@penguincomputing.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ARM: at91: smc: bug fix in sam9_smc_cs_read()

commit 1588c51cf6d782e63a8719681d905ef0ac22ee62 upstream.

There was a copy/paste error when reading the nwe_pulse value.

Signed-off-by: Jean-Jacques Hiblot <jjhiblot@traphandler.com>
Acked-by: Boris BREZILLON <b.brezillon@overkiz.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tty/serial: at91: Handle shutdown more safely

commit 0cc7c6c7916b1b6f34350ff1473b80b9f7e459c0 upstream.

Interrupts were being cleaned up late in the shutdown handler, it is possible
that an interrupt can occur and schedule a tasklet that runs after the port is
cleaned up. There is a null dereference due to this race condition with the
following stacktrace:

[<c02092b0>] (atmel_tasklet_func+0x514/0x814) from [<c001fd34>] (tasklet_action+0x70/0xa8)
[<c001fd34>] (tasklet_action+0x70/0xa8) from [<c001f60c>] (__do_softirq+0x90/0x144)
[<c001f60c>] (__do_softirq+0x90/0x144) from [<c001fa18>] (irq_exit+0x40/0x4c)
[<c001fa18>] (irq_exit+0x40/0x4c) from [<c000e298>] (handle_IRQ+0x64/0x84)
[<c000e298>] (handle_IRQ+0x64/0x84) from [<c000d6c0>] (__irq_svc+0x40/0x50)
[<c000d6c0>] (__irq_svc+0x40/0x50) from [<c0208060>] (atmel_rx_dma_release+0x88/0xb8)
[<c0208060>] (atmel_rx_dma_release+0x88/0xb8) from [<c0209740>] (atmel_shutdown+0x104/0x160)
[<c0209740>] (atmel_shutdown+0x104/0x160) from [<c0205e8c>] (uart_port_shutdown+0x2c/0x38)

Signed-off-by: Marek Roszko <mark.roszko@gmail.com>
Acked-by: Leilei Zhao <leilei.zhao@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: vt6656: CARDqGetNextTBTT correct uLowNextTBTT

commit 9acec059c0cef0bf086c738f4c0b1f4447782a48 upstream.

value uLowNextTBTT yields wrong value.

ULL is needed with qwTSF

Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: vt6656: [BUG] BBvUpdatePreEDThreshold Always set sensitivity on bScanning

commit 8f248dae133668bfb8e9379b4b3f0571c858b24a upstream.

byBBPreEDIndex value is initially 0, this means that from
cold BBvUpdatePreEDThreshold is never set.

This means that sensitivity may be in an ambiguous state,
failing to scan any wireless points or at least distant ones.

Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: r8712u: Set device type to wlan

commit 3a21f00a5002b14e4aab52aef59d33ed28468a13 upstream.

The latest version of NetworkManager does not recognize the device as wireless
without this change.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

b43: fix the wrong assignment of status.freq in b43_rx()

commit 64e5acb09ca6b50c97299cff9ef51299470b29f2 upstream.

Use the right function to update frequency value.

If rx skb is probe response or beacon, the wrong frequency value can
cause problem that bss info can't be updated when it should be.

Fixes: 8318d78a44d4 ("cfg80211 API for channels/bitrates, mac80211 and driver conversion")
Signed-off-by: ZHAO Gang <gamerh2o@gmail.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

b43legacy: Fix unload oops if firmware is not available

commit 452028665312672c6ba9e16a19248ee00ead9400 upstream.

The asyncronous firmware load uses a completion struct to hold firmware
processing until the user-space routines are up and running. There is.
however, a problem in that the waiter is nevered canceled during teardown.
As a result, unloading the driver when firmware is not available causes an oops.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

b43: Fix unload oops if firmware is not available

commit 0673effd41dba323d6a280ef37b5ef29f3f5a653 upstream.

The asyncronous firmware load uses a completion struct to hold firmware
processing until the user-space routines are up and running. There is.
however, a problem in that the waiter is nevered canceled during teardown.
As a result, unloading the driver when firmware is not available causes an oops.

To be able to access the completion structure at teardown, it had to be moved
into the b43_wldev structure.

This patch also fixes a typo in a comment.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

b43: Fix lockdep splat

commit 09164043f63c947a49797750a09ca1cd7c31108e upstream.

In https://bugzilla.kernel.org/show_bug.cgi?id=67561, a locking dependency is reported
when b43 is used with hostapd, and rfkill is used to kill the radio output.

The lockdep splat (in part) is as follows:

======================================================
[ INFO: possible circular locking dependency detected ]
3.12.0 #1 Not tainted
-------------------------------------------------------
rfkill/10040 is trying to acquire lock:
 (rtnl_mutex){+.+.+.}, at: [<ffffffff8146f282>] rtnl_lock+0x12/0x20

but task is already holding lock:
 (rfkill_global_mutex){+.+.+.}, at: [<ffffffffa04832ca>] rfkill_fop_write+0x6a/0x170 [rfkill]

--snip--

Chain exists of:
  rtnl_mutex --> misc_mtx --> rfkill_global_mutex

The fix is to move the initialization of the hardware random number generator
outside the code range covered by the rtnl_mutex.

Reported-by: yury <urykhy@gmail.com>
Tested-by: yury <urykhy@gmail.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iwlwifi: mvm: fix missing cleanup in .start() error path

commit 91b0d1198417cf4fd9a7bd4138b6909f0b359099 upstream.

Cleanup of iwl_mvm_leds was missing in case of error,
resulting in the following warning:

WARNING: at lib/kobject.c:196 kobject_add_internal+0x1f4/0x210()
kobject_add_internal failed for phy0-led with -EEXIST, don't try to register things with the same name in the same directory.

which prevents further reloads of the driver.

Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mwifiex: fix wrong 11ac bits setting in fw_cap_info

commit 1e202242ee1432d68a8bea4919b2ae0ef19d9e06 upstream.

bit 14 is actually reserved and bit 12 & 13 should be used for
11ac capability in fw_cap_info.

Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mwifiex: add missing endian conversion for fw_tsf

commit 9795229752c31da0c5f8a7dc4c827665327b52f9 upstream.

It is u64 data received from firmware. Little endian to cpu
conversion is required here.

Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

rtlwifi: rtl8188ee: Fix typo in code

commit f699273d6a624266ebc9198774f06ee64a3847a1 upstream.

The static analyser "cppcheck" shows the following typo:
drivers/net/wireless/rtlwifi/rtl8188ee/dm.c:1081]: (style) Same expression on both sides of '!='.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Reported-by: David Binderman <dcb314@hotmail.com>
Cc: David Binderman <dcb314@hotmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

rtlwifi: Add missing code to PWDB statics routine

commit d82403a9f407217b6aed5260aa92a120e8e98310 upstream.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

rtlwifi: rtl8192cu: Fix some code in RF handling

commit e9b0784bb9de3152e787ee779868c626b137fb3b upstream.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

rtlwifi: rtl8192cu: Update the power index registers

commit 9806eacf5de27ab01d680c5d75c92a3a89734e4f upstream.

This patch uses the newly introduced power index register routines.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

rtlwifi: rtl8192c: Add routines to save/restore power index registers

commit 97204e93f01868eeba6ae5c4f3270f32905bb418 upstream.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

rtlwifi: Increase the RX queue length for USB drivers

commit dc6405712268fe514d3dd89aa936c4397b0871b9 upstream.

The current number of RX buffers queued is 32, which is too small under
heavy load. That number is doubled.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

rtlwifi: rtl8192c: Add new definitions in the dm_common header

commit c908c74e005de780fddbe8cb6fcd44803f5d4b74 upstream.

Changes in the gain-control mechanism will require some changes in the header.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

rtlwifi: Set the link state

commit 619ce76f8bb850b57032501a39f26aa6c6731c70 upstream.

The present code fails to set the linked state when an interface is
added.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

rtlwifi: Redo register save locations

commit b9a758a8c905fc59e783ae91ad645452d877ea88 upstream.

The initial USB driver did not use some register save locations in the
private data storage. To save some memory, a union was used to overlay these
variables with USB I/O components. In an update of the gain-control code,
these register save locations are now needed for USB drivers.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

rtlwifi: rtl8192cu: Add new firmware

commit 62009b7f12793c932aaba0df946b04cb4a77d022 upstream.

Vendor driver rtl8188C_8192C_8192D_usb_linux_v3.4.2_3727.20120404 introduced
new firmware for these chips. The code try for the new file, and fall back to
the original firmware if the new file is not available.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

rtlwifi: rtl8192c: Prevent reconnect attempts if not connected

commit 8fd77aec1a9d6f4328fc0244f21932114e066df3 upstream.

This driver has a watchdog timer that attempts to reconnect when beacon frames
are not seen for 6 seconds. This patch disables that reconnect whenever the
device has never been connected.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

rtlwifi: Update beacon statistics for USB driver

commit 65b9cc97c6852fae19dc5c7745e9abc8dd380aad upstream.

The USB drivers were not updating the beacon statistics, which led to
false beacon loss indications.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

rtlwifi: rtl8192cu: Add new device ID

commit f87f960b2fb802f26ee3b00c19320e57a9c583ff upstream.

Reported-by: Jan Prinsloo <janroot@gmail.com>
Tested-by: Jan Prinsloo <janroot@gmail.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: ehci: add freescale imx28 special write register method

commit feffe09f510c475df082546815f9e4a573f6a233 upstream.

According to Freescale imx28 Errata, "ENGR119653 USB: ARM to USB
register error issue", All USB register write operations must
use the ARM SWP instruction. So, we implement a special ehci_write
for imx28.

Discussion for it at below:
http://marc.info/?l=linux-usb&m=137996395529294&w=2

Without this patcheset, imx28 works unstable at high AHB bus loading.
If the bus loading is not high, the imx28 usb can work well at the most
of time. There is a IC errata for this problem, usually, we consider
IC errata is a problem not a new feature, and this workaround is needed
for that, so we need to add them to stable tree 3.11+.

Cc: robert.hodaszi@digi.com
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Tested-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: fix race between hub_disconnect and recursively_mark_NOTATTACHED

commit 543d7784b07ffd16cc82a9cb4e1e0323fd0040f1 upstream.

There is a race in the hub driver between hub_disconnect() and
recursively_mark_NOTATTACHED().  This race can be triggered if the
driver is unbound from a device at the same time as the bus's root hub
is removed.  When the race occurs, it can cause an oops:

BUG: unable to handle kernel NULL pointer dereference at 0000015c
IP: [<c16d5fb0>] recursively_mark_NOTATTACHED+0x20/0x60
Call Trace:
 [<c16d5fc4>] recursively_mark_NOTATTACHED+0x34/0x60
 [<c16d5fc4>] recursively_mark_NOTATTACHED+0x34/0x60
 [<c16d5fc4>] recursively_mark_NOTATTACHED+0x34/0x60
 [<c16d5fc4>] recursively_mark_NOTATTACHED+0x34/0x60
 [<c16d6082>] usb_set_device_state+0x92/0x120
 [<c16d862b>] usb_disconnect+0x2b/0x1a0
 [<c16dd4c0>] usb_remove_hcd+0xb0/0x160
 [<c19ca846>] ? _raw_spin_unlock_irqrestore+0x26/0x50
 [<c1704efc>] ehci_mid_remove+0x1c/0x30
 [<c1704f26>] ehci_mid_stop_host+0x16/0x30
 [<c16f7698>] penwell_otg_work+0xd28/0x3520
 [<c19c945b>] ? __schedule+0x39b/0x7f0
 [<c19cdb9d>] ? sub_preempt_count+0x3d/0x50
 [<c125e97d>] process_one_work+0x11d/0x3d0
 [<c19c7f4d>] ? mutex_unlock+0xd/0x10
 [<c125e0e5>] ? manage_workers.isra.24+0x1b5/0x270
 [<c125f009>] worker_thread+0xf9/0x320
 [<c19ca846>] ? _raw_spin_unlock_irqrestore+0x26/0x50
 [<c125ef10>] ? rescuer_thread+0x2b0/0x2b0
 [<c1264ac4>] kthread+0x94/0xa0
 [<c19d0f77>] ret_from_kernel_thread+0x1b/0x28
 [<c1264a30>] ? kthread_create_on_node+0xc0/0xc0

One problem is that recursively_mark_NOTATTACHED() uses the intfdata
value and hub->hdev->maxchild while hub_disconnect() is clearing them.
Another problem is that it uses hub->ports[i] while the port device is
being released.

To fix this race, we need to hold the device_state_lock while
hub_disconnect() changes the values.  (Note that usb_disconnect()
and hub_port_connect_change() already acquire this lock at similar
critical times during a USB device's life cycle.)  We also need to
remove the port devices after maxchild has been set to 0, instead of
before.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: "Du, Changbin" <changbinx.du@intel.com>
Tested-by: "Du, Changbin" <changbinx.du@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: xhci: Check for XHCI_PLAT in xhci_cleanup_msix()

commit 9005355af23856c55a5538c9024355785424821b upstream.

If CONFIG_PCI is enabled, make sure xhci_cleanup_msix()
doesn't try to free a bogus PCI IRQ or dereference an invalid
pci_dev when the xHCI device is actually a platform_device.

This patch should be backported to kernels as old as 3.9, that
contain the commit 52fb61250a7a132b0cfb9f4a1060a1f3c49e5a25
"xhci-plat: Don't enable legacy PCI interrupts."

Signed-off-by: Jack Pham <jackp@codeaurora.org>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: Nokia 502 is an unusual device

commit 0e16114f2db4838251fb64f3b550996ad3585890 upstream.

The USB storage operation of Nokia Asha 502 Dual SIM smartphone running Asha
Platform 1.1.1 is unreliable in respect of data consistency (i.e. transfered
files are corrupted). A similar issue is described here:
http://discussions.nokia.com/t5/Asha-and-other-Nokia-Series-30/Nokia-301-USB-transfers-and-corrupted-files/td-p/1974170

The workaround is (MAX_SECTORS_64):
   rmmod usb_storage && modprobe usb_storage quirks=0421:06aa:m

The patch adds the tested device to the unusual list permanently.

Signed-off-by: Mikhail Zolotaryov <lebon@lebon.org.ua>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: ftdi_sio: added CS5 quirk for broken smartcard readers

commit c1f15196ac3b541d084dc80a8fbd8a74c6a0bd44 upstream.

Genuine FTDI chips support only CS7/8. A previous fix in commit
8704211f65a2 ("USB: ftdi_sio: fixed handling of unsupported CSIZE
setting") enforced this limitation and reported it back to userspace.

However, certain types of smartcard readers depend on specific
driver behaviour that requests 0 data bits (not 5) to change into a
different operating mode if CS5 has been set.

This patch reenables this behaviour for all FTDI devices.

Tagged to be added to stable, because it affects a lot of users of
embedded systems which rely on these readers to work properly.

Reported-by: Heinrich Siebmanns <H.Siebmanns@t-online.de>
Tested-by: Heinrich Siebmanns <H.Siebmanns@t-online.de>
Signed-off-by: Colin Leitner <colin.leitner@gmail.com>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: cypress_m8: fix ring-indicator detection and reporting

commit 440ebadeae9298d7de3d4d105342691841ec88d0 upstream.

Fix ring-indicator (RI) status-bit definition, which was defined as CTS,
effectively preventing RI-changes from being detected while reporting
false RI status.

This bug predates git.

Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: serial: add support for iBall 3.5G connect usb modem

commit 7d5c1b9c7cb5ec8e52b1adc65c484a923a8ea6c3 upstream.

Add support for iBall 3.5G connect usb modem.

$lsusb
Bus 002 Device 006: ID 1c9e:9605 OMEGA TECHNOLOGY

$usb-devices
T:  Bus=02 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  6 Spd=480 MxCh= 0
D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=1c9e ProdID=9605 Rev=00.00
S:  Manufacturer=USB Modem
S:  Product=USB Modem
S:  SerialNumber=1234567890ABCDEF
C:  #Ifs= 5 Cfg#= 1 Atr=e0 MxPwr=500mA
I:  If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I:  If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I:  If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I:  If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I:  If#= 4 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage

Signed-off-by: Rahul Bedarkar <rahulbedarkar89@gmail.com>
Suggested-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: option: add new zte 3g modem pids to option driver

commit 4d90b819ae4c7ea8fd5e2bb7edc68c0f334be2e4 upstream.

Signed-off-by: Jun zhang <zhang.jun92@zte.com.cn>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: pl2303: fix data corruption on termios updates

commit 623c8263376c0b8a4b0c220232e7313d762cd0cc upstream.

Some PL2303 devices are known to lose bytes if you change serial
settings even to the same values as before. Avoid this by comparing the
encoded settings with the previsouly used ones before configuring the
device.

The common case was fixed by commit bf5e5834bffc6 ("pl2303: Fix mode
switching regression"), but this problem was still possible to trigger,
for instance, by using the TCSETS2-interface to repeatedly request
115201 baud, which gets mapped to 115200 and thus always triggers a
settings update.

Cc: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

KVM: x86: limit PIT timer frequency

commit 9ed96e87c5748de4c2807ef17e81287c7304186c upstream.

Limit PIT timer frequency similarly to the limit applied by
LAPIC timer.

Reviewed-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

x86/efi: Fix off-by-one bug in EFI Boot Services reservation

commit a7f84f03f660d93574ac88835d056c0d6468aebe upstream.

Current code check boot service region with kernel text region by:
start+size >= __pa_symbol(_text)
The end of the above region should be start + size - 1 instead.

I see this problem in ovmf + Fedora 19 grub boot:
text start: 1000000 md start: 800000 md size: 800000

Signed-off-by: Dave Young <dyoung@redhat.com>
Acked-by: Borislav Petkov <bp@suse.de>
Acked-by: Toshi Kani <toshi.kani@hp.com>
Tested-by: Toshi Kani <toshi.kani@hp.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

x86, x32: Correct invalid use of user timespec in the kernel

commit 2def2ef2ae5f3990aabdbe8a755911902707d268 upstream.

The x32 case for the recvmsg() timout handling is broken:

  asmlinkage long compat_sys_recvmmsg(int fd, struct compat_mmsghdr __user *mmsg,
                                      unsigned int vlen, unsigned int flags,
                                      struct compat_timespec __user *timeout)
  {
          int datagrams;
          struct timespec ktspec;

          if (flags & MSG_CMSG_COMPAT)
                  return -EINVAL;

          if (COMPAT_USE_64BIT_TIME)
                  return __sys_recvmmsg(fd, (struct mmsghdr __user *)mmsg, vlen,
                                        flags | MSG_CMSG_COMPAT,
                                        (struct timespec *) timeout);
          ...

The timeout pointer parameter is provided by userland (hence the __user
annotation) but for x32 syscalls it's simply cast to a kernel pointer
and is passed to __sys_recvmmsg which will eventually directly
dereference it for both reading and writing.  Other callers to
__sys_recvmmsg properly copy from userland to the kernel first.

The bug was introduced by commit ee4fa23c4bfc ("compat: Use
COMPAT_USE_64BIT_TIME in net/compat.c") and should affect all kernels
since 3.4 (and perhaps vendor kernels if they backported x32 support
along with this code).

Note that CONFIG_X86_X32_ABI gets enabled at build time and only if
CONFIG_X86_X32 is enabled and ld can build x32 executables.

Other uses of COMPAT_USE_64BIT_TIME seem fine.

This addresses CVE-2014-0038.

Signed-off-by: PaX Team <pageexec@freemail.hu>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mm/mempolicy.c: fix mempolicy printing in numa_maps

commit 8790c71a18e5d2d93532ae250bcf5eddbba729cd upstream.

As a result of commit 5606e3877ad8 ("mm: numa: Migrate on reference
policy"), /proc/<pid>/numa_maps prints the mempolicy for any <pid> as
"prefer:N" for the local node, N, of the process reading the file.

This should only be printed when the mempolicy of <pid> is
MPOL_PREFERRED for node N.

If the process is actually only using the default mempolicy for local
node allocation, make sure "default" is printed as expected.

Signed-off-by: David Rientjes <rientjes@google.com>
Reported-by: Robert Lippert <rlippert@google.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Acked-by: Mel Gorman <mgorman@suse.de>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: <stable@vger.kernel.org> [3.7+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

e1000e: fix compiler warnings

commit 9e6c3b63399dd424d33a34e08b77f2cab0b84cdc upstream.

This patch is to fix a compiler warning of __bad_udelay due to a value
of >999 being passed as a parameter to udelay() in the function
e1000e_phy_has_link_generic().  This affects the gcc compiler when
it is given a flag of -O3 and the icc compiler.

This patch is also making the change from mdelay() to msleep() in the
same function, since it was determined though code inspection that this
function is never called in atomic context.

Signed-off-by: David Ertman <davidx.m.ertman@intel.com>
Acked-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

e752x_edac: Fix pci_dev usage count

commit 90ed4988b8c030d65b41b7d13140e9376dc6ec5a upstream.

In case the device 0, function 1 is not found using pci_get_device(),
pci_scan_single_device() will be used but, differently than
pci_get_device(), it allocates a pci_dev but doesn't does bump the usage
count on the pci_dev and after few module removals and loads the pci_dev
will be freed.

Signed-off-by: Aristeu Rozanski <aris@redhat.com>
Reviewed-by: mark gross <mark.gross@intel.com>
Link: http://lkml.kernel.org/r/20131205153755.GL4545@redhat.com
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mm: hugetlbfs: fix hugetlbfs optimization

commit 27c73ae759774e63313c1fbfeb17ba076cea64c5 upstream.

Commit 7cb2ef56e6a8 ("mm: fix aio performance regression for database
caused by THP") can cause dereference of a dangling pointer if
split_huge_page runs during PageHuge() if there are updates to the
tail_page->private field.

Also it is repeating compound_head twice for hugetlbfs and it is running
compound_head+compound_trans_head for THP when a single one is needed in
both cases.

The new code within the PageSlab() check doesn't need to verify that the
THP page size is never bigger than the smallest hugetlbfs page size, to
avoid memory corruption.

A longstanding theoretical race condition was found while fixing the
above (see the change right after the skip_unlock label, that is
relevant for the compound_lock path too).

By re-establishing the _mapcount tail refcounting for all compound
pages, this also fixes the below problem:

  echo 0 >/sys/kernel/mm/hugepages/hugepages-2048kB/nr_hugepages

  BUG: Bad page state in process bash  pfn:59a01
  page:ffffea000139b038 count:0 mapcount:10 mapping:          (null) index:0x0
  page flags: 0x1c00000000008000(tail)
  Modules linked in:
  CPU: 6 PID: 2018 Comm: bash Not tainted 3.12.0+ #25
  Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011
  Call Trace:
    dump_stack+0x55/0x76
    bad_page+0xd5/0x130
    free_pages_prepare+0x213/0x280
    __free_pages+0x36/0x80
    update_and_free_page+0xc1/0xd0
    free_pool_huge_page+0xc2/0xe0
    set_max_huge_pages.part.58+0x14c/0x220
    nr_hugepages_store_common.isra.60+0xd0/0xf0
    nr_hugepages_store+0x13/0x20
    kobj_attr_store+0xf/0x20
    sysfs_write_file+0x189/0x1e0
    vfs_write+0xc5/0x1f0
    SyS_write+0x55/0xb0
    system_call_fastpath+0x16/0x1b

Signed-off-by: Khalid Aziz <khalid.aziz@oracle.com>
Signed-off-by: Andrea Arcangeli <aarcange@redhat.com>
Tested-by: Khalid Aziz <khalid.aziz@oracle.com>
Cc: Pravin Shelar <pshelar@nicira.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Ben Hutchings <bhutchings@solarflare.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Johannes Weiner <jweiner@redhat.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Rik van Riel <riel@redhat.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Minchan Kim <minchan@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Guillaume Morin <guillaume@morinfr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

lib/decompressors: fix "no limit" output buffer length

commit 1431574a1c4c669a0c198e4763627837416e4443 upstream.

When decompressing into memory, the output buffer length is set to some
arbitrarily high value (0x7fffffff) to indicate the output is, virtually,
unlimited in size.

The problem with this is that some platforms have their physical memory at
high physical addresses (0x80000000 or more), and that the output buffer
address and its "unlimited" length cannot be added without overflowing.
An example of this can be found in inflate_fast():

/* next_out is the output buffer address */
out = strm->next_out - OFF;
/* avail_out is the output buffer size. end will overflow if the output
 * address is >= 0x80000104 */
end = out + (strm->avail_out - 257);

This has huge consequences on the performance of kernel decompression,
since the following exit condition of inflate_fast() will be always true:

} while (in < last && out < end);

Indeed, "end" has overflowed and is now always lower than "out".  As a
result, inflate_fast() will return after processing one single byte of
input data, and will thus need to be called an unreasonably high number of
times.  This probably went unnoticed because kernel decompression is fast
enough even with this issue.

Nonetheless, adjusting the output buffer length in such a way that the
above pointer arithmetic never overflows results in a kernel decompression
that is about 3 times faster on affected machines.

Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Tested-by: Jon Medhurst <tixy@linaro.org>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/nouveau/bios: fix offset calculation for BMPv1 bioses

commit 5d2f4767c4eacab351b8450b0de4d3261fe1a957 upstream.

The only BIOS on record that needs the 14 offset has a bios major
version 2 but BMP version 1.01. Another bunch of BIOSes that need the 18
offset have BMP version 2.01 or 5.01 or higher. So instead of looking at the
bios major version, look at the BMP version. BIOSes with BMP version 0
do not contain a detectable script, so always return 0 for them.

See https://bugs.freedesktop.org/show_bug.cgi?id=68835

Reported-by: Mauro Molinari <mauromol@tiscali.it>
Signed-off-by: Ilia Mirkin <imirkin@alum.mit.edu>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

md/raid5: fix long-standing problem with bitmap handling on write failure.

commit 9f97e4b128d2ea90a5f5063ea0ee3b0911f4c669 upstream.

Before a write starts we set a bit in the write-intent bitmap.
When the write completes we clear that bit if the write was successful
to all devices.  However if the write wasn't fully successful we
should not clear the bit.  If the faulty drive is subsequently
re-added, the fact that the bit is still set ensure that we will
re-write the data that is missing.

This logic is mediated by the STRIPE_DEGRADED flag - we only clear the
bitmap bit when this flag is not set.
Currently we correctly set the flag if a write starts when some
devices are failed or missing.  But we do *not* set the flag if some
device failed during the write attempt.
This is wrong and can result in clearing the bit inappropriately.

So: set the flag when a write fails.

This bug has been present since bitmaps were introduces, so the fix is
suitable for any -stable kernel.

Reported-by: Ethan Wilson <ethan.wilson@shiftmail.org>
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

kvm: x86: fix apic_base enable check

commit 0dce7cd67fd9055c4a2ff278f8af1431e646d346 upstream.

Commit e66d2ae7c67bd moved the assignment
vcpu->arch.apic_base = value above a condition with
(vcpu->arch.apic_base ^ value), causing that check
to always fail. Use old_value, vcpu->arch.apic_base's
old value, in the condition instead.

Signed-off-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Linux 3.10.28

ARM: 7938/1: OMAP4/highbank: Flush L2 cache before disabling

commit b25f3e1c358434bf850220e04f28eebfc45eb634 upstream.

Kexec disables outer cache before jumping to reboot code, but it doesn't
flush it explicitly. Flush is done implicitly inside of l2x0_disable().
But some SoC's override default .disable handler and don't flush cache.
This may lead to a corrupted memory during Kexec reboot on these
platforms.

This patch adds cache flush inside of OMAP4 and Highbank outer_cache.disable()
handlers to make it consistent with default l2x0_disable().

Acked-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Taras Kondratiuk <taras.kondratiuk@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Wang Nan <wangnan0@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/i915: Don't grab crtc mutexes in intel_modeset_gem_init()

commit 7ad228b11ec26a820291c9f5a1168d6176580dc1 upstream.

When the pipe A force quirk is applied the code will attempt to grab
a crtc mutex during intel_modeset_setup_hw_state(). If we're already
holding all crtc mutexes this will obviously deadlock every time.

So instead of using drm_modeset_lock_all() just grab the
mode_config.mutex. This is enough to avoid the unlocked mutex warnings
from certain lower level functions.

The regression was introduced in:

 commit 027476642811f8559cbe00ef6cc54db230e48a20
 Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
 Date:   Mon Dec 2 11:08:06 2013 +0200

    drm/i915: Take modeset locks around intel_modeset_setup_hw_state()

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[danvet: Add cc: stable since the offending commit has that, too.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

serial: amba-pl011: use port lock to guard control register access

commit fe43390702a1b5741fdf217063b05c7612b38303 upstream.

When the pl011 is being used for a console, pl011_console_write forces
the control register (CR) to enable the UART for transmission and then
restores this to the original value afterwards. It does this while
holding the port lock.

Unfortunately, when the uart is started or shutdown - say in response to
userland using the serial device for a terminal - then this updates the
control register without any locking.

This means we can have

  pl011_console_write   Save CR
  pl011_startup         Initialise CR, e.g. enable receive
  pl011_console_write   Restore old CR with receive not enabled

this result is a serial port which doesn't respond to any input.

A similar race in reverse could happen when the device is shutdown.

We can fix these problems by taking the port lock when updating CR.

Signed-off-by: Jon Medhurst <tixy@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mm: Make {,set}page_address() static inline if WANT_PAGE_VIRTUAL

commit f92f455f67fef27929e6043499414605b0c94872 upstream.

{,set}page_address() are macros if WANT_PAGE_VIRTUAL.  If
!WANT_PAGE_VIRTUAL, they're plain C functions.

If someone calls them with a void *, this pointer is auto-converted to
struct page * if !WANT_PAGE_VIRTUAL, but causes a build failure on
architectures using WANT_PAGE_VIRTUAL (arc, m68k and sparc64):

  drivers/md/bcache/bset.c: In function `__btree_sort':
  drivers/md/bcache/bset.c:1190: warning: dereferencing `void *' pointer
  drivers/md/bcache/bset.c:1190: error: request for member `virtual' in something not a structure or union

Convert them to static inline functions to fix this.  There are already
plenty of users of struct page members inside <linux/mm.h>, so there's
no reason to keep them as macros.

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

md/raid5: Fix possible confusion when multiple write errors occur.

commit 1cc03eb93245e63b0b7a7832165efdc52e25b4e6 upstream.

commit 5d8c71f9e5fbdd95650be00294d238e27a363b5c
    md: raid5 crash during degradation

Fixed a crash in an overly simplistic way which could leave
R5_WriteError or R5_MadeGood set in the stripe cache for devices
for which it is no longer relevant.
When those devices are removed and spares added the flags are still
set and can cause incorrect behaviour.

commit 14a75d3e07c784c004b4b44b34af996b8e4ac453
    md/raid5: preferentially read from replacement device if possible.

Fixed the same bug if a more effective way, so we can now revert
the original commit.

Reported-and-tested-by: Alexander Lyakas <alex.bolshoy@gmail.com>
Fixes: 5d8c71f9e5fbdd95650be00294d238e27a363b5c
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

md/raid10: fix two bugs in handling of known-bad-blocks.

commit b50c259e25d9260b9108dc0c2964c26e5ecbe1c1 upstream.

If we discover a bad block when reading we split the request and
potentially read some of it from a different device.

The code path of this has two bugs in RAID10.
1/ we get a spin_lock with _irq, but unlock without _irq!!
2/ The calculation of 'sectors_handled' is wrong, as can be clearly
   seen by comparison with raid1.c

This leads to at least 2 warnings and a probable crash is a RAID10
ever had known bad blocks.

Fixes: 856e08e23762dfb92ffc68fd0a8d228f9e152160
Reported-by: Damian Nowak <spam@nowaker.net>
URL: https://bugzilla.kernel.org/show_bug.cgi?id=68181
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>