Philipp Tomsich [Fri, 28 Oct 2016 10:21:28 +0000 (18:21 +0800)]
sunxi: DRAM initialisation for sun9i
This adds DRAM initialisation code for sun9i, which calculates the
appropriate timings based on timing information for the supplied
DDR3 bin and the clock speeds used.
With this DRAM setup, we have verified DDR3 clocks of up to 792MHz
(i.e. DDR3-1600) on the A80-Q7 using a dual-channel configuration.
[wens@csie.org: Moved dram_sun9i.c to arch/arm/mach-sunxi/; style cleanup]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
[hdegoede@redhat.com: Drop some huge non-documenting #if 0 ... #endif blocks]
[hdegoede@redhat.com: Fix checkpatch warnings]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Stefan Brüns [Sat, 29 Oct 2016 10:23:18 +0000 (12:23 +0200)]
tools: add mksunxiboot to tools-all target
mksunxiboot is useful outside of u-boot, it is e.g. used by sunxi-tools.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Amit Singh Tomar [Fri, 21 Oct 2016 01:24:30 +0000 (02:24 +0100)]
sunxi: A64: enable USB support
Mostly by adding MACH_SUN50I to some existing #ifdefs enable support
for the the HCI0 USB host controller on the A64.
Fix up some minor 64-bit hiccups on the way.
Add the bare minimum DT bits to the A64 .dtsi and enable the controllers
and the PHY on the Pine64.
This is limited to the first USB controller at the moment, which is
connected to the lower USB socket on the Pine64 board.
[Andre: remove unneeded defines, enable OHCI, add commit message]
Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Stefan Mavrodiev [Sat, 29 Oct 2016 12:34:07 +0000 (14:34 +0200)]
sunxi: Update DRAM clock for Olimex A20 boards
Originally dram clock was set to 480MHz, but this behaves
unstable. To improve stability the clock is reduced to 384MHz
Signed-off-by: Stefan Mavrodiev <stefan.mavrodiev@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Andre Przywara [Fri, 21 Oct 2016 00:11:46 +0000 (01:11 +0100)]
sunxi: dts: Pine64: add Ethernet alias
The sun8i-emac driver works fine with the A64 Ethernet IP, but we are
missing an alias entry to trigger the driver instantiation by U-Boot.
Add the line to point U-Boot to the Ethernet DT node.
This enables TFTP boot on the Pine64.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Masahiro Yamada [Thu, 13 Oct 2016 15:40:01 +0000 (00:40 +0900)]
sunxi: remove unneeded CONFIG_USB_MAX_CONTROLLER_COUNT defines
ARCH_SUNXI selects DM_USB, where CONFIG_USB_MAX_CONTROLLER_COUNT
is not used.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Jagan Teki [Thu, 13 Oct 2016 08:49:35 +0000 (14:19 +0530)]
sunxi: Rename CONFIG_SUNXI to CONFIG_ARCH_SUNXI
CONFIG_SUNXI -> CONFIG_ARCH_SUNXI
and removed CONFIG_SUNIX from config_whitelist.txt
Cc: Simon Glass <sjg@chromium.org>
Cc: Ian Campbell <ijc@hellion.org.uk>
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Tom Rini [Sat, 29 Oct 2016 12:41:45 +0000 (08:41 -0400)]
configs/chromebox_panther_defconfig: Re-enable CONFIG_DM_PCI
This was turned off by accident, re-enble.
Signed-off-by: Tom Rini <trini@konsulko.com>
Jagan Teki [Fri, 28 Oct 2016 17:57:34 +0000 (23:27 +0530)]
MAINTAINERS: Update Jagan's email
Signed-off-by: Jagan Teki <jagan@openedev.com>
Stephen Warren [Wed, 26 Oct 2016 19:05:52 +0000 (13:05 -0600)]
travis-ci: build Tegra boards
ARMv7 Tegra boards aren't currently covered by any other travis-ci jobs.
Add a new job to build them.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Stephen Warren [Wed, 26 Oct 2016 17:05:36 +0000 (11:05 -0600)]
travis-ci: compile with buildman when running test/py
Use buildman to compile any U-Boot binary tested by test/py. This
re-uses all the work done elsewhere to make buildman work within
Travis-CI, in particular related to toolchain downloading and buildman
config file creation.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Stephen Warren [Wed, 26 Oct 2016 17:05:35 +0000 (11:05 -0600)]
travis-ci: don't invoke exit on success
Invoking exit prevents any subsequent build commands from running, and
future patches will add extra commands.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Stephen Warren [Wed, 26 Oct 2016 17:05:34 +0000 (11:05 -0600)]
travis-ci: use buildman -P everywhere
This places build results into a board-specific directory rather than a
buildman-thread-specific directory. This is required so that we can
access the directory from test.py, and there's no risk of a particular
build's results being over-written by another build performed by the
same thread.
In theory, this can lead to slower builds when building many different
boards in a single buildman thread, since it removes the possibility of
incremental builds between boards. In practice however I didn't notice
longer build times when when enabling this option; if anything build
times decreased although I suspect that's simply due to general
variations in build performance across different machines within the
Travis CI infra-structure.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Stephen Warren [Wed, 26 Oct 2016 17:05:33 +0000 (11:05 -0600)]
travis-ci: centralize ~/.buildman editing
Any time an x86 toolchain is used, we need to edit ~/.buildman to
reference it. Move the editing logic into a central place so that it
doesn't have to be duplicated everywhere that uses the x86 toolchain;
future patches will add additional cases where it's used.
It would be nice if we could unconditionally write all of ~/.buildman at
once. Unfortunately, buildman fails if any toolchain mentioned in a
toolchain-prefix entry doesn't exist, even if it doesn't need to use it
for the current build.
The sandbox/x86 build definition currently does nothing more than edit
~/.buildman; no builds are run. Fix this by not defining a custom script
for this build, and hence preventing that stanza from replacing the
default script.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Stephen Warren [Wed, 26 Oct 2016 17:05:32 +0000 (11:05 -0600)]
travis-ci: use correct exit code on errors
The phrase "if [ $? -ne 0 ]; then exit $?; fi" doesn't work correctly;
by the time the "exit" statement runs, $? has already been over-written
by the result of the [ command. Fix this by explicitly storing $? and
then using that stored value in both the test and the error-case exit
statement.
This change also converts from textual comparison to integer comparison,
since the exit code is an integer and there's no need to convert it to
a string for comparison.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Stephen Warren [Wed, 26 Oct 2016 17:05:31 +0000 (11:05 -0600)]
travis-ci: Use = not : when writing ~/.buildman
Travis CI seems to be confused when there's a colon in an echo command,
and this is currently worked around using a variable that contains the
text we want to echo. Use = syntax instead so that we can remove the
work-around; it's rather confusing until you find out what it's for.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Stephen Warren [Mon, 24 Oct 2016 22:41:49 +0000 (16:41 -0600)]
travis-ci: remove duplicate build
There were two sub-jobs to build arm1136. Remove the duplicate.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Stephen Warren [Mon, 24 Oct 2016 22:41:48 +0000 (16:41 -0600)]
travis-ci: set env vars to name jobs
Travis CI names sub-jobs after the first environment variable that is set
for a script. This doesn't produce meaningful results for any of the non-
buildman jobs. Add a dummy variable to give the jobs meaningful names.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Tom Rini [Fri, 28 Oct 2016 18:14:18 +0000 (14:14 -0400)]
Merge branch 'master' of git://git.denx.de/u-boot-atmel
Wenyou Yang [Fri, 28 Oct 2016 06:17:49 +0000 (14:17 +0800)]
dm: at91: Add driver model support for the spi driver
Add driver model support while retaining the existing legacy code.
This allows the driver to support boards that have converted to
driver model as well as those that have not.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
Wenyou Yang [Mon, 17 Oct 2016 01:55:26 +0000 (09:55 +0800)]
board: sama5d2_xplained: Enable an early debug UART
Enable an early debug UART to debug problems when an ICE or other
debug mechanism is not available.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
Wenyou Yang [Mon, 17 Oct 2016 01:55:25 +0000 (09:55 +0800)]
board: sama5d2_xplained: Set 'ethaddr' got from AT24MAC
If 'ethaddr' is not set, we will get the ethernet address from AT24MAC,
and set it to 'ethaddr' variable.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: Songjun Wu <songjun.wu@microchip.com>
Reviewed-by: Andreas Bießmann <biessmann@corscience.de>
Wenyou Yang [Mon, 17 Oct 2016 01:55:24 +0000 (09:55 +0800)]
board: sama5d2_xplained: Clean up code
Since the introduction of pinctrl and clk driver, and the dts file,
remove unneeded the pin configurations and the clock enabling code.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
Wenyou Yang [Mon, 17 Oct 2016 01:55:23 +0000 (09:55 +0800)]
board: sama5d2_xplained: Move config options to defconfigs
Move the config options from the include/configs/sama5d2_xplained.h
to configs/sama5d2_xplained_*_defconfig.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
Wenyou Yang [Mon, 17 Oct 2016 01:49:55 +0000 (09:49 +0800)]
serial: atmel_usart: Support enable an early debug UART
Add support to enable an early debug UART for debugging.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
Wenyou Yang [Mon, 17 Oct 2016 01:49:54 +0000 (09:49 +0800)]
serial: Kconfig: Add ATMEL_USART option
Add ATMEL_USART option to support to enable the Atmel usart driver
from Kconfig.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
Wenyou Yang [Tue, 27 Sep 2016 03:00:34 +0000 (11:00 +0800)]
mmc: atmel_sdhci: Remove unnecessary clock calling
Due to the peripheral and generated clock driver improvement,
remove the unnecessary clock calling.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Wenyou Yang [Tue, 27 Sep 2016 03:00:33 +0000 (11:00 +0800)]
usb: ehci-atmel: Remove unnecessary clock calling
Due to the peripheral clock driver improvement, remove the
unnecessary clock calling.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
Wenyou Yang [Tue, 27 Sep 2016 03:00:32 +0000 (11:00 +0800)]
i2c: at91_i2c: Change error return -ENODEV to -EINVAL
Change the error return value -ENODEV from to -EINVAL for more
reasonable.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Wenyou Yang [Tue, 27 Sep 2016 03:00:31 +0000 (11:00 +0800)]
i2c: at91_i2c: Remove unnecessary clock calling
Due to the peripheral clock driver improvement, remove the
unnecessary clock calling.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Wenyou Yang [Tue, 27 Sep 2016 03:00:30 +0000 (11:00 +0800)]
gpio: atmel_pio4: Remove unnecessary clock calling
Due to the peripheral clock driver improvement, remove the
unnecessary clock calling.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Wenyou Yang [Tue, 27 Sep 2016 03:00:29 +0000 (11:00 +0800)]
clk: at91: Improve the clock implementation
For the peripheral clock, provide the clock ops for the clock
provider, such as spi0_clk. The .of_xlate is to get the clk->id,
the .enable is to enable the spi0 peripheral clock, the .get_rate
is to get the clock frequency.
The driver for periph32ck node is responsible for recursively
binding its children as clk devices, not provide the clock ops.
So do the generated clock and system clock.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Wenyou Yang [Tue, 27 Sep 2016 03:00:28 +0000 (11:00 +0800)]
clk: clk-uclass: Assign clk->dev before call .of_xlate
In order to make clk->dev available in ops->of_xlate() to get the
clock ID from the 'reg' property of the clock node, assign the
clk->dev before calling ops->of_xlate().
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Wenyou Yang [Sun, 18 Sep 2016 07:37:47 +0000 (15:37 +0800)]
ARM: at91/dt: sama5d2: Fix the warning from dtc
Fix the warning from dtc like,
---8<----
Warning (unit_address_vs_reg): Node /ahb/apb/pmc@
f0014000/periph64ck/sdmmc0_hclk has a reg or ranges property, but no unit name
--->8----
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Wenyou Yang [Tue, 13 Sep 2016 02:25:55 +0000 (10:25 +0800)]
clk: at91: Fix at91-pmc and at91-sckc's class ID
The at91-pmc and at91-sckc aren't the clock providers, change their
class ID from UCLASS_CLK to UCLASS_SIMPLE_BUS, they also don't
need to bind the child nodes explicitly, the .post_bind callback
of simple_bus uclass will do it for them.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Robert P. J. Day [Thu, 1 Sep 2016 13:49:14 +0000 (09:49 -0400)]
AT91: Correct misspelling of "redundent" in partition names
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
Heiko Schocher [Wed, 17 Aug 2016 07:13:25 +0000 (09:13 +0200)]
arm, at91: add icache support
add at least icache support for at91 based boards.
This speeds up NOR flash access on an at91sam9g15
based board from 15.2 seconds reading 8 MiB from
a SPI NOR flash to 5.7 seconds.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
Heiko Schocher [Wed, 17 Aug 2016 07:13:24 +0000 (09:13 +0200)]
ARM: at91: clock: correct PRES offset for at91sam9x5
on at91sam9x5 PRES offset is 4 in the PMC master
clock register.
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Wenyou Yang <wenyou.yang@atmel.com>
Acked-by: Andreas Bießmann <andreas@biessmann.org>
Heiko Schocher [Wed, 17 Aug 2016 07:13:23 +0000 (09:13 +0200)]
arm: at91: mpddrc: add missing MPDDRC_MD defines
add missing MPDDRC_MD defines
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
Tom Rini [Fri, 28 Oct 2016 15:12:03 +0000 (11:12 -0400)]
Merge branch 'master' of git://denx.de/git/u-boot-imx
Signed-off-by: Tom Rini <trini@konsulko.com>
Conflicts:
common/Kconfig
configs/dms-ba16_defconfig
Tom Rini [Fri, 28 Oct 2016 13:08:13 +0000 (09:08 -0400)]
Merge branch 'master' of git.denx.de/u-boot-mmc
Bin Meng [Mon, 17 Oct 2016 06:35:18 +0000 (23:35 -0700)]
pci: Move CONFIG_PCI_PNP to Kconfig
Introduce CONFIG_PCI_PNP in Kconfig and move over boards' defconfig
to use that.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Re-generate configs and include/configs/ changes]
Signed-off-by: Tom Rini <trini@konsulko.com>
Jaehoon Chung [Fri, 21 Oct 2016 11:52:35 +0000 (20:52 +0900)]
mmc: sdhci: assign to clk_mul when host version is upper than SD3.0
To prevent the wrong value check the SD version.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Jaehoon Chung [Mon, 24 Oct 2016 06:22:22 +0000 (15:22 +0900)]
mmc: add the device name in debugging message for supplying vmmc
If vmmc didn't supply, we didn't know which card didn't supply vmmc.
And changed from "put" to "debug".
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Sylvain Lesne [Mon, 24 Oct 2016 16:24:37 +0000 (18:24 +0200)]
dm: mmc: socfpga: fix MMC_OPS support
Now that CONFIG_BLK and CONFIG_MMC_OPS are enabled by default with
CONFIG_DM_MMC, the DWMMC driver on the socfpga platform fails at
runtime.
This adds the missing fields in the driver declaration.
Signed-off-by: Sylvain Lesne <lesne@alse-fr.com>
Acked-by: Marek Vasut <marex@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Masahiro Yamada [Thu, 13 Oct 2016 15:13:18 +0000 (00:13 +0900)]
mmc: refactor two core functions
Drop unneeded variables and assignments.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Jaehoon Chung [Thu, 13 Oct 2016 01:33:06 +0000 (10:33 +0900)]
mmc: sdhci: fix the "misaligned operation at range" for cache
This pathc is fixed the below thing.
If misaligned the cache range, Just flush to CACHLINE_SIZE.
"CACHE: Misaligned operation at range [
7ae55b00,
7ae55b08]"
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Peng Fan [Tue, 11 Oct 2016 07:08:43 +0000 (15:08 +0800)]
mmc: introduce mmc_power_init
In device tree, there is vmmc-supply property for SD/MMC.
Introduce mmc_power_init function to handle vmmc-supply.
mmc_power_init will first invoke board_mmc_power_init to
avoid break boards which already implement board_mmc_power_init.
If DM_MMC and DM_REGULATOR is defined, the regulator
will be enabled to power up the device.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Tom Rini [Wed, 26 Oct 2016 21:15:37 +0000 (17:15 -0400)]
drivers/pci/Kconfig: Add PCI
Add 'PCI' as a menu option and migrate all existing users.
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Jagan Teki [Sat, 8 Oct 2016 12:30:28 +0000 (18:00 +0530)]
imx6: icorem6: Add default mtd nand partition table
icorem6qdl> mtdparts
device nand0 <nand>, # parts = 6
0: spl 0x00200000 0x00000000 0
1: uboot 0x00200000 0x00200000 0
2: env 0x00100000 0x00400000 0
3: kernel 0x00400000 0x00500000 0
4: dtb 0x00100000 0x00900000 0
5: rootfs 0x1f600000 0x00a00000 0
Cc: Stefano Babic <sbabic@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Jagan Teki [Sat, 8 Oct 2016 12:30:27 +0000 (18:00 +0530)]
imx6: icorem6: Enable MTD device support
Enable MTD device, partition and command support.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Jagan Teki [Tue, 25 Oct 2016 06:23:23 +0000 (11:53 +0530)]
imx6: icorem6: Add NAND support
Add NAND support for Engicam i.CoreM6 qdl board.
Boot Log:
--------
U-Boot SPL 2016.09-rc2-30755-gd3dc581-dirty (Sep 28 2016 - 23:00:43)
Trying to boot from NAND
NAND : 512 MiB
U-Boot 2016.09-rc2-30755-gd3dc581-dirty (Sep 28 2016 - 23:00:43 +0530)
CPU: Freescale i.MX6SOLO rev1.3 at 792MHz
CPU: Industrial temperature grade (-40C to 105C) at 55C
Reset cause: WDOG
Model: Engicam i.CoreM6 DualLite/Solo Starter Kit
DRAM: 256 MiB
NAND: 512 MiB
MMC: FSL_SDHC: 0
In: serial
Out: serial
Err: serial
Net: FEC [PRIME]
Hit any key to stop autoboot: 0
icorem6qdl>
Cc: Scott Wood <oss@buserror.net>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Jagan Teki [Sat, 8 Oct 2016 12:30:25 +0000 (18:00 +0530)]
mtd: nand: Kconfig: Add NAND_MXS entry
Added kconfig for NAND_MXS driver.
Cc: Scott Wood <oss@buserror.net>
Cc: Simon Glass <sjg@chromium.org>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Jagan Teki [Sat, 8 Oct 2016 12:30:24 +0000 (18:00 +0530)]
arm: imx6q: Add devicetree support for Engicam i.CoreM6 Quad/Dual
i.CoreM6 Quad/Dual modules are system on module solutions
manufactured by Engicam with following characteristics:
CPU NXP i.MX6 DQ, 800MHz
RAM 1GB, 32, 64 bit, DDR3-800/1066
NAND SLC,512MB
Power supply Single 5V
MAX LCD RES FULLHD
and more info at
http://www.engicam.com/en/products/embedded/som/sodimm/i-core-m6s-dl-d-q
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Jagan Teki [Sat, 8 Oct 2016 12:30:23 +0000 (18:00 +0530)]
arm: dts: imx6q: Add pinctrl defines
Add imx6q pinctrl defines support from Linux.
Here is the last commit:
"ARM: dts: imx: pinfunc: add MX6QDL_PAD_GPIO_6__ENET_IRQ"
(sha1:
d8c765e0d1ddbd5032c2491c82cc9660c2f0e7f2)
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Jagan Teki [Sat, 8 Oct 2016 12:30:22 +0000 (18:00 +0530)]
arm: dts: Add devicetree for i.MX6Q
Add i.MX6Q dtsi support from Linux.
Here is the last commit:
"ARM: dts: add gpio-ranges property to iMX GPIO controllers"
(sha1:
bb728d662bed0fe91b152550e640cb3f6caa972c)
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Jagan Teki [Tue, 25 Oct 2016 06:23:22 +0000 (11:53 +0530)]
engicam: icorem6: Add DM_GPIO, DM_MMC support
Add DM_GPIO, DM_MMC support for u-boot and disable for SPL.
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Jagan Teki [Sat, 8 Oct 2016 12:30:20 +0000 (18:00 +0530)]
imx6q: icorem6: Enable pinctrl driver
Enable imx6 pinctrl driver support for i.CoreM6.
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Jagan Teki [Sat, 8 Oct 2016 12:30:19 +0000 (18:00 +0530)]
arm: imx6q: Add devicetree support for Engicam i.CoreM6 DualLite/Solo
i.CoreM6 DualLite/Solo modules are system on module solutions
manufactured by Engicam with following characteristics:
CPU NXP i.MX6 DL, 800MHz
RAM 1GB, 32, 64 bit, DDR3-800/1066
NAND SLC,512MB
Power supply Single 5V
MAX LCD RES FULLHD
and more info at
http://www.engicam.com/en/products/embedded/som/sodimm/i-core-m6s-dl-d-q
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Jagan Teki [Sat, 8 Oct 2016 12:30:18 +0000 (18:00 +0530)]
dt-bindings: clock: imx6qdl: Add clock defines
Add imx6qdl clock header defines support from Linux.
"clk: imx: Add clock support for imx6qp"
(sha1:
ee36027427c769b0b9e5e205fe43aced93d6aa66)
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Jagan Teki [Sat, 8 Oct 2016 12:30:17 +0000 (18:00 +0530)]
arm: dts: imx6dl: Add pinctrl defines
Add imx6dl pinctrl defines support from Linux.
Here is the last commit:
"ARM: dts: imx: pinfunc: add MX6QDL_PAD_GPIO_6__ENET_IRQ"
(sha1:
d8c765e0d1ddbd5032c2491c82cc9660c2f0e7f2)
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Jagan Teki [Sat, 8 Oct 2016 12:30:16 +0000 (18:00 +0530)]
arm: dts: Add devicetree for i.MX6DQL
Add i.MX6DQL dtsi support from Linux.
Here is the last commit:
"ARM: dts: imx6qdl: Fix SPDIF regression"
(sha1:
f065e9e4addd75c21bb976bb2558648bf4f61de6)
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Jagan Teki [Sat, 8 Oct 2016 12:30:15 +0000 (18:00 +0530)]
arm: dts: Add devicetree for i.MX6DL
Add i.MX6DL dtsi support from Linux.
Here is the last commit:
"ARM: dts: add gpio-ranges property to iMX GPIO controllers"
(sha1:
bb728d662bed0fe91b152550e640cb3f6caa972c)
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Jagan Teki [Sat, 8 Oct 2016 12:30:14 +0000 (18:00 +0530)]
imx: s/docs\/README.imximage/doc\/README.imximage/g
Fixed typo for doc/README.imximage on respective imximage.cfg files.
Cc: Tom Rini <trini@konsulko.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Jagan Teki [Sat, 8 Oct 2016 12:30:13 +0000 (18:00 +0530)]
imx6: icorem6: Add ENET support
Add enet support for engicam icorem6 qdl starter kit.
- Add pinmux settings
- Add board_eth_init
TFTP log:
--------
Net: FEC [PRIME]
Hit any key to stop autoboot: 0
icorem6qdl> tftpboot {fdt_addr} imx6dl-icore.dtb
Using FEC device
TFTP from server 192.168.2.96; our IP address is 192.168.2.75
Filename 'imx6dl-icore.dtb'.
Load address: 0x0
Loading: ######
1.3 MiB/s
done
Bytes transferred = 28976 (7130 hex)
CACHE: Misaligned operation at range [
00000000,
00007130]
icorem6qdl>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Jagan Teki [Sat, 8 Oct 2016 12:30:12 +0000 (18:00 +0530)]
net: Kconfig: Add FEC_MXC entry
Added kconfig for FEC_MXC driver.
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Jagan Teki [Sat, 8 Oct 2016 12:30:11 +0000 (18:00 +0530)]
arm: imx: Add Engicam i.CoreM6 QDL Starter Kit initial support
Boot Log for i.CoreM6 DualLite/Solo Starter Kit:
-----------------------------------------------
U-Boot SPL 2016.09-rc2-30739-gd1fa290 (Sep 17 2016 - 00:37:46)
Trying to boot from MMC1
U-Boot 2016.09-rc2-30739-gd1fa290 (Sep 17 2016 - 00:37:46 +0530)
CPU: Freescale i.MX6SOLO rev1.3 at 792MHz
CPU: Industrial temperature grade (-40C to 105C) at 31C
Reset cause: POR
DRAM: 256 MiB
MMC: FSL_SDHC: 0
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Net: CPU Net Initialization Failed
No ethernet found.
Hit any key to stop autoboot: 0
switch to partitions #0, OK
mmc0 is current device
switch to partitions #0, OK
mmc0 is current device
reading boot.scr
** Unable to read file boot.scr **
reading zImage
6741808 bytes read in 341 ms (18.9 MiB/s)
Booting from mmc ...
reading imx6dl-icore.dtb
30600 bytes read in 19 ms (1.5 MiB/s)
Booting using the fdt blob at 0x18000000
Using Device Tree in place at
18000000, end
1800a787
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0x0
Boot Log for i.CoreM6 Quad/Dual Starter Kit:
--------------------------------------------
U-Boot SPL 2016.09-rc2-30739-gd1fa290 (Sep 17 2016 - 00:37:46)
Trying to boot from MMC1
U-Boot 2016.09-rc2-30739-gd1fa290 (Sep 17 2016 - 00:37:46 +0530)
CPU: Freescale i.MX6Q rev1.2 at 792MHz
CPU: Industrial temperature grade (-40C to 105C) at 28C
Reset cause: POR
DRAM: 512 MiB
MMC: FSL_SDHC: 0
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Net: CPU Net Initialization Failed
No ethernet found.
Hit any key to stop autoboot: 0
icorem6qdl>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Jagan Teki [Sat, 8 Oct 2016 12:30:10 +0000 (18:00 +0530)]
config: Move CONFIG_DEFAULT_FDT_FILE to defconfigs
- Add DEFAULT_FDT_FILE kconfig entry
- Move CONFIG_DEFAULT_FDT_FILE from include/configs to defconfigs
Cc: Tom Rini <trini@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Jagan Teki [Sat, 8 Oct 2016 12:30:09 +0000 (18:00 +0530)]
thermal: Kconfig: Add IMX_THERMAL entry
Added kconfig for IMX_THERMAL driver.
Cc: Simon Glass <sjg@chromium.org>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Jagan Teki [Sat, 8 Oct 2016 12:30:08 +0000 (18:00 +0530)]
serial: Kconfig: Add MXC_UART entry
Added kconfig for MXC_UART driver.
Cc: Simon Glass <sjg@chromium.org>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Peng Fan [Tue, 11 Oct 2016 06:29:17 +0000 (14:29 +0800)]
imx: mx6ull_14x14_evk: add plugin defconfig
Add defconfig file to use plugin code.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Marek Vasut [Thu, 20 Oct 2016 14:48:28 +0000 (16:48 +0200)]
i2c: designware: Avoid overwriting the cmd_data register
Make sure the driver writes the cmd_data register only once per
read transfer instead of doing so potentially repeatedly.
In case the read transfer didn't finish quickly enough, the loop
in the driver code would spin fast enough to write the same value
into the cmd_data register again before re-checking whether the
transfer completed, which would cause another spurious read transfer
on the bus.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Chin Liang See <clsee@altera.com>
Tom Rini [Thu, 20 Oct 2016 15:26:40 +0000 (11:26 -0400)]
travis-ci: Add test.py for various qemu platforms
- Add a PPA for a more recent qemu (required for PowerPC to work)
- Add tests to run test.py for various QEMU platforms. This relies on
swarren's uboot-test-hooks repository to provide the abstractions.
Acked-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Thu, 20 Oct 2016 15:24:52 +0000 (11:24 -0400)]
travis-ci: Drop 'TEST_CMD'
We don't need to use TEST_CMD in order to run tests. We need a BUILDMAN
and TOOLCHAIN variable to avoid having to duplicate logic or write some
wrapper function. But this makes the tests harder as we add more
complex examples.
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Tom Rini [Thu, 20 Oct 2016 15:23:15 +0000 (11:23 -0400)]
travis-ci: Add more architectures
We can now build for microblaze, sh4 and xtensa.
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Tom Rini [Thu, 20 Oct 2016 15:08:26 +0000 (11:08 -0400)]
travis-ci: Update toolchain and buildman usage
- Drop the 'cache' line, travis-ci says to not cache apt packages (and
does not).
- Get the Ubuntu provided toolchain for ARM and PowerPC.
- Add more toolchain options that buildman can fetch.
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Tom Rini [Thu, 20 Oct 2016 15:05:57 +0000 (11:05 -0400)]
travis-ci: Do not make buildman warnings fatal
We currently will always see a number of warnings due to device tree
issues. These (and other warnings) should not make the build be marked
as failure so catch exit status 129 specifically and return 0 in that
case.
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Tom Rini [Thu, 20 Oct 2016 15:04:10 +0000 (11:04 -0400)]
travis-ci: Use a git URI for dtc.git
Currently we fail to fetch the dtc.git tree due to an SSL issue within
the travis-ci environment. The easiest fix here is to switch to a git
URI.
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Tom Rini [Thu, 20 Oct 2016 15:03:19 +0000 (11:03 -0400)]
travis-ci: Switch to Ubuntu 14.04 'Trusty Tahr'
In order to make other various improvements, update to the latest
environment travis-ci supports.
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Emmanuel Vadot [Wed, 19 Oct 2016 15:19:47 +0000 (17:19 +0200)]
api: storage: Avoid enumeration for non-configured subsystem
If a subsystem wasn't configured, avoid enumeration.
Signed-off-by: Emmanuel Vadot <manu@bidouilliste.com>
Masahiro Yamada [Wed, 19 Oct 2016 05:39:54 +0000 (14:39 +0900)]
tools: moveconfig: support wildcards in --defconfigs file
Supporting shell-style wildcards for the --defconfigs option will be
useful to run the moveconfig tool against a specific platform. For
example, "uniphier*" in the file passed by --defconfigs option will
be expanded to defconfig files that start with "uniphier". This is
easier than listing out all defconfig files you are interested in.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Masahiro Yamada [Mon, 17 Oct 2016 11:43:01 +0000 (20:43 +0900)]
Fix codying style broken by recent libfdt sync
Commit
b02e4044ff8e ("libfdt: Bring in upstream stringlist
functions") broke codying style in some places especially
by inserting an extra whitespace before fdt_stringlist_count().
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Simon Glass <sjg@chromium.org>
Masahiro Yamada [Mon, 17 Oct 2016 11:22:34 +0000 (20:22 +0900)]
libfdt: fix fdt_stringlist_search()
If fdt_getprop() fails, negative error code should be returned.
[ DTC commit:
daa75e8fa5942caa8e97931aed3a1ee0b7edd74b ]
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Masahiro Yamada [Mon, 17 Oct 2016 11:22:33 +0000 (20:22 +0900)]
libfdt: fix fdt_stringlist_count()
If fdt_getprop() fails, negative error code should be returned.
[ DTC commit:
e28eff5b787adb3f461d1653598818b2f1f25a73 ]
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Nicolae Rosia [Thu, 13 Oct 2016 10:47:53 +0000 (13:47 +0300)]
power: twl6030: fix code refactoring
Commit
a85362fb3e1fc7833723accddbbae431091d06b8 refactored the code
but the register read ended up in the wrong if branch.
Currently, the else branch checks a variable which is always 0.
Signed-off-by: Nicolae Rosia <nicolae_rosia@mentor.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Stefan Brüns [Sun, 9 Oct 2016 18:15:28 +0000 (20:15 +0200)]
ext4: Only write journal entries for modified blocks in unlink_filename
Instead of creating a journal entry for each directory block, even
if the block is unmodified, only log the modified block.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Stefan Brüns [Sun, 9 Oct 2016 18:15:27 +0000 (20:15 +0200)]
ext4: Fix handling of direntlen in unlink_filename
The direntlen checks were quite bogus, i.e. the loop termination used
"len + offset == blocksize" (exact match only), and checked for a
direntlen less than 0. The latter can never happen as the len is
unsigned, this has been reported by Coverity, CID 153384.
Use the same code as in search_dir for directory traversal. This code
has the correct checks for direntlen >= sizeof(struct dirent), and
offset < blocksize.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Reported-by: Coverity (CID: 153383, 153384)
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Stefan Brüns [Sun, 9 Oct 2016 18:15:26 +0000 (20:15 +0200)]
ext4: cleanup unlink_filename function
Use the same variable names as in search_dir, to make purpose of variables
more obvious.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Tom Rini [Mon, 24 Oct 2016 12:04:21 +0000 (08:04 -0400)]
Merge git://git.denx.de/u-boot-fdt
Peng Fan [Tue, 11 Oct 2016 06:29:16 +0000 (14:29 +0800)]
imx: mx6ullevk: correct boot device macro
Correct boot device macro according to kconfig entry
in common/Kconfig
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Peng Fan [Tue, 11 Oct 2016 06:29:15 +0000 (14:29 +0800)]
imx: mx6ullevk: support plugin
Add plugin code for mx6ullevk.
Define CONFIG_USE_IMXIMG_PLUGIN in defconfig file to use plugin code.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Peng Fan [Tue, 11 Oct 2016 06:29:14 +0000 (14:29 +0800)]
imx-common: compile plugin code
If CONFIG_USE_IMXIMG_PLUGIN is selected, plugin.bin will be
generated under board/$(BOARDDIR)/.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Peng Fan [Tue, 11 Oct 2016 06:29:12 +0000 (14:29 +0800)]
imx-common: introduce USE_IMXIMG_PLUGIN Kconfig
Introduce USE_IMXIMG_PLUGIN Kconfig
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Peng Fan [Tue, 11 Oct 2016 06:29:11 +0000 (14:29 +0800)]
imx: mx7: Add plugin support
Add mx7_plugin.S which calls boot rom setup function, generate the second ivt,
and jump back to boot rom.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Peng Fan [Tue, 11 Oct 2016 06:29:10 +0000 (14:29 +0800)]
imx: mx6: Add plugin support
Add mx6_plugin.S which calls boot rom setup function, generate the second ivt,
and jump back to boot rom.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Utkarsh Gupta <utkarsh.gupta@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Utkarsh Gupta <utkarsh.gupta@nxp.com>
Peng Fan [Tue, 11 Oct 2016 06:29:09 +0000 (14:29 +0800)]
tools: imximage: add plugin support
Add plugin support for imximage.
Define CONFIG_USE_IMXIMG_PLUGIN in defconfig to enable using plugin.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Eric Nelson <eric@nelint.com>
Cc: Ye Li <ye.li@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Simon Glass [Tue, 18 Oct 2016 02:13:02 +0000 (20:13 -0600)]
Convert CONFIG_SYS_STDIO_DEREGISTER to Kconfig
This converts the following to Kconfig:
CONFIG_SYS_STDIO_DEREGISTER
This option should never be enabled in SPL, so use
CONFIG_IS_ENABLED(SYS_STDIO_DEREGISTER) when checking the option.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Re-sync]
Signed-off-by: Tom Rini <trini@konsulko.com>
Simon Glass [Tue, 18 Oct 2016 02:13:01 +0000 (20:13 -0600)]
Convert CONFIG_USB_KEYBOARD to Kconfig
This converts the following to Kconfig:
CONFIG_USB_KEYBOARD
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Fixup MPC86* configs]
Signed-off-by: Tom Rini <trini@konsulko.com>
Simon Glass [Tue, 18 Oct 2016 02:13:00 +0000 (20:13 -0600)]
Convert CONFIG_SYS_CONSOLE_INFO_QUIET to Kconfig
This converts the following to Kconfig:
CONFIG_SYS_CONSOLE_INFO_QUIET
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Make this default n, re-run the migration]
Signed-off-by: Tom Rini <trini@konsulko.com>
Simon Glass [Tue, 18 Oct 2016 02:12:59 +0000 (20:12 -0600)]
Convert CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE to Kconfig
This converts the following to Kconfig:
CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>