Mark Brown [Mon, 10 Aug 2015 18:43:47 +0000 (19:43 +0100)]
regulator: core: Use class device list for regulator_list in late init
[ Upstream commit
609ca5f3cb32c2d11fd8cabe293ff3689e7d2613 ]
The regulator_list has exactly the same contents as the list that the
driver core maintains of regulator_class members so is redundant. As a
first step in converting over to use the class device list convert our
iteration in late_initcall() to use the class device iterator.
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Anilkumar Kolli [Fri, 11 Mar 2016 06:16:39 +0000 (11:46 +0530)]
ath10k: fix debugfs pktlog_filter write
[ Upstream commit
9ddc486aa09a3413a6c492fcf160ce61bfccb7b1 ]
It is observed that, we are disabling the packet log if we write same
value to the pktlog_filter for the second time. Always enable pktlogs
on non zero filter.
Fixes:
90174455ae05 ("ath10k: add support to configure pktlog filter")
Cc: stable@vger.kernel.org
Signed-off-by: Anilkumar Kolli <akolli@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Rajkumar Manoharan [Wed, 2 Mar 2016 14:43:52 +0000 (20:13 +0530)]
ath10k: fix firmware assert in monitor mode
[ Upstream commit
8a75fc54745fd3ce9062ab1cc6429a9da9ac2a68 ]
commit
166de3f1895d ("ath10k: remove supported chain mask") had revealed
an issue on monitor mode. Configuring NSS upon monitor interface
creation is causing target assert in all qca9888x and qca6174 firmware.
Firmware assert issue can be reproduced by below sequence even after
reverting commit
166de3f1895d ("ath10k: remove supported chain mask").
ip link set wlan0 down
iw wlan0 set type monitor
iw phy0 set antenna 7
ip link set wlan0 up
This issue is originally reported on qca9888 with 10.1 firmware.
Fixes:
5572a95b4b ("ath10k: apply chainmask settings to vdev on creation")
Cc: stable@vger.kernel.org
Reported-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Sasha Levin [Mon, 30 May 2016 21:50:36 +0000 (17:50 -0400)]
perf/x86/intel/pt: Generate PMI in the STOP region as well
[ Upstream commit
ab92b232ae05c382c3df0e3d6a5c6d16b639ac8c ]
Currently, the PT driver always sets the PMI bit one region (page) before
the STOP region so that we can wake up the consumer before we run out of
room in the buffer and have to disable the event. However, we also need
an interrupt in the last output region, so that we actually get to disable
the event (if no more room from new data is available at that point),
otherwise hardware just quietly refuses to start, but the event is
scheduled in and we end up losing trace data till the event gets removed.
For a cpu-wide event it is even worse since there may not be any
re-scheduling at all and no chance for the ring buffer code to notice
that its buffer is filled up and the event needs to be disabled (so that
the consumer can re-enable it when it finishes reading the data out). In
other words, all the trace data will be lost after the buffer gets filled
up.
This patch makes PT also generate a PMI when the last output region is
full.
Reported-by: Markus Metzger <markus.t.metzger@intel.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: <stable@vger.kernel.org>
Cc: Arnaldo Carvalho de Melo <acme@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: vince@deater.net
Link: http://lkml.kernel.org/r/1462886313-13660-2-git-send-email-alexander.shishkin@linux.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Sasha Levin [Sat, 21 May 2016 01:46:13 +0000 (21:46 -0400)]
Linux 4.1.25
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Linus Torvalds [Sat, 14 May 2016 18:11:44 +0000 (11:11 -0700)]
nf_conntrack: avoid kernel pointer value leak in slab name
[ Upstream commit
31b0b385f69d8d5491a4bca288e25e63f1d945d0 ]
The slab name ends up being visible in the directory structure under
/sys, and even if you don't have access rights to the file you can see
the filenames.
Just use a 64-bit counter instead of the pointer to the 'net' structure
to generate a unique name.
This code will go away in 4.7 when the conntrack code moves to a single
kmemcache, but this is the backportable simple solution to avoiding
leaking kernel pointers to user space.
Fixes:
5b3501faa874 ("netfilter: nf_conntrack: per netns nf_conntrack_cachep")
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Junxiao Bi [Thu, 12 May 2016 22:42:18 +0000 (15:42 -0700)]
ocfs2: fix posix_acl_create deadlock
[ Upstream commit
c25a1e0671fbca7b2c0d0757d533bd2650d6dc0c ]
Commit
702e5bc68ad2 ("ocfs2: use generic posix ACL infrastructure")
refactored code to use posix_acl_create. The problem with this function
is that it is not mindful of the cluster wide inode lock making it
unsuitable for use with ocfs2 inode creation with ACLs. For example,
when used in ocfs2_mknod, this function can cause deadlock as follows.
The parent dir inode lock is taken when calling posix_acl_create ->
get_acl -> ocfs2_iop_get_acl which takes the inode lock again. This can
cause deadlock if there is a blocked remote lock request waiting for the
lock to be downconverted. And same deadlock happened in ocfs2_reflink.
This fix is to revert back using ocfs2_init_acl.
Fixes:
702e5bc68ad2 ("ocfs2: use generic posix ACL infrastructure")
Signed-off-by: Tariq Saeed <tariq.x.saeed@oracle.com>
Signed-off-by: Junxiao Bi <junxiao.bi@oracle.com>
Cc: Mark Fasheh <mfasheh@suse.de>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Joseph Qi <joseph.qi@huawei.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Junxiao Bi [Thu, 12 May 2016 22:42:15 +0000 (15:42 -0700)]
ocfs2: revert using ocfs2_acl_chmod to avoid inode cluster lock hang
[ Upstream commit
5ee0fbd50fdf1c1329de8bee35ea9d7c6a81a2e0 ]
Commit
743b5f1434f5 ("ocfs2: take inode lock in ocfs2_iop_set/get_acl()")
introduced this issue. ocfs2_setattr called by chmod command holds
cluster wide inode lock when calling posix_acl_chmod. This latter
function in turn calls ocfs2_iop_get_acl and ocfs2_iop_set_acl. These
two are also called directly from vfs layer for getfacl/setfacl commands
and therefore acquire the cluster wide inode lock. If a remote
conversion request comes after the first inode lock in ocfs2_setattr,
OCFS2_LOCK_BLOCKED will be set. And this will cause the second call to
inode lock from the ocfs2_iop_get_acl() to block indefinetly.
The deleted version of ocfs2_acl_chmod() calls __posix_acl_chmod() which
does not call back into the filesystem. Therefore, we restore
ocfs2_acl_chmod(), modify it slightly for locking as needed, and use that
instead.
Fixes:
743b5f1434f5 ("ocfs2: take inode lock in ocfs2_iop_set/get_acl()")
Signed-off-by: Tariq Saeed <tariq.x.saeed@oracle.com>
Signed-off-by: Junxiao Bi <junxiao.bi@oracle.com>
Cc: Mark Fasheh <mfasheh@suse.de>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Joseph Qi <joseph.qi@huawei.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Junxiao Bi [Fri, 11 Dec 2015 21:41:03 +0000 (13:41 -0800)]
ocfs2: fix SGID not inherited issue
[ Upstream commit
854ee2e944b4daf795e32562a7d2f9e90ab5a6a8 ]
Commit
8f1eb48758aa ("ocfs2: fix umask ignored issue") introduced an
issue, SGID of sub dir was not inherited from its parents dir. It is
because SGID is set into "inode->i_mode" in ocfs2_get_init_inode(), but
is overwritten by "mode" which don't have SGID set later.
Fixes:
8f1eb48758aa ("ocfs2: fix umask ignored issue")
Signed-off-by: Junxiao Bi <junxiao.bi@oracle.com>
Cc: Mark Fasheh <mfasheh@suse.de>
Cc: Joel Becker <jlbec@evilplan.org>
Acked-by: Srinivas Eeda <srinivas.eeda@oracle.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Alex Deucher [Wed, 11 May 2016 20:16:53 +0000 (16:16 -0400)]
drm/radeon: fix DP mode validation
[ Upstream commit
ff0bd441bdfbfa09d05fdba9829a0401a46635c1 ]
Switch the order of the loops to walk the rates on the top
so we exhaust all DP 1.1 rate/lane combinations before trying
DP 1.2 rate/lane combos.
This avoids selecting rates that are supported by the monitor,
but not the connector leading to valid modes getting rejected.
bug:
https://bugs.freedesktop.org/show_bug.cgi?id=95206
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Wanpeng Li [Wed, 11 May 2016 09:55:18 +0000 (17:55 +0800)]
workqueue: fix rebind bound workers warning
[ Upstream commit
f7c17d26f43d5cc1b7a6b896cd2fa24a079739b9 ]
------------[ cut here ]------------
WARNING: CPU: 0 PID: 16 at kernel/workqueue.c:4559 rebind_workers+0x1c0/0x1d0
Modules linked in:
CPU: 0 PID: 16 Comm: cpuhp/0 Not tainted 4.6.0-rc4+ #31
Hardware name: IBM IBM System x3550 M4 Server -[7914IUW]-/00Y8603, BIOS -[D7E128FUS-1.40]- 07/23/2013
0000000000000000 ffff881037babb58 ffffffff8139d885 0000000000000010
0000000000000000 0000000000000000 0000000000000000 ffff881037babba8
ffffffff8108505d ffff881037ba0000 000011cf3e7d6e60 0000000000000046
Call Trace:
dump_stack+0x89/0xd4
__warn+0xfd/0x120
warn_slowpath_null+0x1d/0x20
rebind_workers+0x1c0/0x1d0
workqueue_cpu_up_callback+0xf5/0x1d0
notifier_call_chain+0x64/0x90
? trace_hardirqs_on_caller+0xf2/0x220
? notify_prepare+0x80/0x80
__raw_notifier_call_chain+0xe/0x10
__cpu_notify+0x35/0x50
notify_down_prepare+0x5e/0x80
? notify_prepare+0x80/0x80
cpuhp_invoke_callback+0x73/0x330
? __schedule+0x33e/0x8a0
cpuhp_down_callbacks+0x51/0xc0
cpuhp_thread_fun+0xc1/0xf0
smpboot_thread_fn+0x159/0x2a0
? smpboot_create_threads+0x80/0x80
kthread+0xef/0x110
? wait_for_completion+0xf0/0x120
? schedule_tail+0x35/0xf0
ret_from_fork+0x22/0x50
? __init_kthread_worker+0x70/0x70
---[ end trace
eb12ae47d2382d8f ]---
notify_down_prepare: attempt to take down CPU 0 failed
This bug can be reproduced by below config w/ nohz_full= all cpus:
CONFIG_BOOTPARAM_HOTPLUG_CPU0=y
CONFIG_DEBUG_HOTPLUG_CPU0=y
CONFIG_NO_HZ_FULL=y
As Thomas pointed out:
| If a down prepare callback fails, then DOWN_FAILED is invoked for all
| callbacks which have successfully executed DOWN_PREPARE.
|
| But, workqueue has actually two notifiers. One which handles
| UP/DOWN_FAILED/ONLINE and one which handles DOWN_PREPARE.
|
| Now look at the priorities of those callbacks:
|
| CPU_PRI_WORKQUEUE_UP = 5
| CPU_PRI_WORKQUEUE_DOWN = -5
|
| So the call order on DOWN_PREPARE is:
|
| CB 1
| CB ...
| CB workqueue_up() -> Ignores DOWN_PREPARE
| CB ...
| CB X ---> Fails
|
| So we call up to CB X with DOWN_FAILED
|
| CB 1
| CB ...
| CB workqueue_up() -> Handles DOWN_FAILED
| CB ...
| CB X-1
|
| So the problem is that the workqueue stuff handles DOWN_FAILED in the up
| callback, while it should do it in the down callback. Which is not a good idea
| either because it wants to be called early on rollback...
|
| Brilliant stuff, isn't it? The hotplug rework will solve this problem because
| the callbacks become symetric, but for the existing mess, we need some
| workaround in the workqueue code.
The boot CPU handles housekeeping duty(unbound timers, workqueues,
timekeeping, ...) on behalf of full dynticks CPUs. It must remain
online when nohz full is enabled. There is a priority set to every
notifier_blocks:
workqueue_cpu_up > tick_nohz_cpu_down > workqueue_cpu_down
So tick_nohz_cpu_down callback failed when down prepare cpu 0, and
notifier_blocks behind tick_nohz_cpu_down will not be called any
more, which leads to workers are actually not unbound. Then hotplug
state machine will fallback to undo and online cpu 0 again. Workers
will be rebound unconditionally even if they are not unbound and
trigger the warning in this progress.
This patch fix it by catching !DISASSOCIATED to avoid rebind bound
workers.
Cc: Tejun Heo <tj@kernel.org>
Cc: Lai Jiangshan <jiangshanlai@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Frédéric Weisbecker <fweisbec@gmail.com>
Cc: stable@vger.kernel.org
Suggested-by: Lai Jiangshan <jiangshanlai@gmail.com>
Signed-off-by: Wanpeng Li <wanpeng.li@hotmail.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Steven Rostedt [Wed, 11 May 2016 19:09:36 +0000 (15:09 -0400)]
tools lib traceevent: Do not reassign parg after collapse_tree()
[ Upstream commit
106b816cb46ebd87408b4ed99a2e16203114daa6 ]
At the end of process_filter(), collapse_tree() was changed to update
the parg parameter, but the reassignment after the call wasn't removed.
What happens is that the "current_op" gets modified and freed and parg
is assigned to the new allocated argument. But after the call to
collapse_tree(), parg is assigned again to the just freed "current_op",
and this causes the tool to crash.
The current_op variable must also be assigned to NULL in case of error,
otherwise it will cause it to be free()ed twice.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Acked-by: Namhyung Kim <namhyung@kernel.org>
Cc: stable@vger.kernel.org # 3.14+
Fixes:
42d6194d133c ("tools lib traceevent: Refactor process_filter()")
Link: http://lkml.kernel.org/r/20160511150936.678c18a1@gandalf.local.home
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Alexander Shishkin [Tue, 10 May 2016 13:18:33 +0000 (16:18 +0300)]
perf/core: Disable the event on a truncated AUX record
[ Upstream commit
9f448cd3cbcec8995935e60b27802ae56aac8cc0 ]
When the PMU driver reports a truncated AUX record, it effectively means
that there is no more usable room in the event's AUX buffer (even though
there may still be some room, so that perf_aux_output_begin() doesn't take
action). At this point the consumer still has to be woken up and the event
has to be disabled, otherwise the event will just keep spinning between
perf_aux_output_begin() and perf_aux_output_end() until its context gets
unscheduled.
Again, for cpu-wide events this means never, so once in this condition,
they will be forever losing data.
Fix this by disabling the event and waking up the consumer in case of a
truncated AUX record.
Reported-by: Markus Metzger <markus.t.metzger@intel.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: <stable@vger.kernel.org>
Cc: Arnaldo Carvalho de Melo <acme@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: vince@deater.net
Link: http://lkml.kernel.org/r/1462886313-13660-3-git-send-email-alexander.shishkin@linux.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Takashi Iwai [Wed, 11 May 2016 15:48:00 +0000 (17:48 +0200)]
ALSA: usb-audio: Yet another Phoneix Audio device quirk
[ Upstream commit
84add303ef950b8d85f54bc2248c2bc73467c329 ]
Phoenix Audio has yet another device with another id (even a different
vendor id, 0556:0014) that requires the same quirk for the sample
rate.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=110221
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Yura Pakhuchiy [Sat, 7 May 2016 16:53:36 +0000 (23:53 +0700)]
ALSA: hda - Fix subwoofer pin on ASUS N751 and N551
[ Upstream commit
3231e2053eaeee70bdfb216a78a30f11e88e2243 ]
Subwoofer does not work out of the box on ASUS N751/N551 laptops. This
patch fixes it. Patch tested on N751 laptop. N551 part is not tested,
but according to [1] and [2] this laptop requires similar changes, so I
included them in the patch.
1. https://github.com/honsiorovskyi/asus-n551-hda-fix
2. https://bugs.launchpad.net/ubuntu/+source/alsa-tools/+bug/1405691
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=117781
Signed-off-by: Yura Pakhuchiy <pakhuchiy@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Bobi Mihalca [Wed, 23 Mar 2016 11:26:11 +0000 (13:26 +0200)]
ALSA: hda - Fix white noise on Asus N750JV headphone
[ Upstream commit
9d4dc5840f93bcb002fa311693349deae7702bc5 ]
For reducing the noise from the headphone output on ASUS N750JV,
call the existing fixup, alc_fixup_auto_mute_via_amp(), additionally.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=115181
Signed-off-by: Bobi Mihalca <bobbymihalca@touchtech.ro>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Bobi Mihalca [Wed, 23 Mar 2016 11:23:55 +0000 (13:23 +0200)]
ALSA: hda - Asus N750JV external subwoofer fixup
[ Upstream commit
70cf2cbd685e218c3ffd105d9fb6cf0f8d767481 ]
ASUS N750JV needs the same fixup as N550 for enabling its subwoofer.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=115181
Signed-off-by: Bobi Mihalca <bobbymihalca@touchtech.ro>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Takashi Iwai [Tue, 10 May 2016 08:24:02 +0000 (10:24 +0200)]
ALSA: hda - Fix broken reconfig
[ Upstream commit
addacd801e1638f41d659cb53b9b73fc14322cb1 ]
The HD-audio reconfig function got broken in the recent kernels,
typically resulting in a failure like:
snd_hda_intel 0000:00:1b.0: control 3:0:0:Playback Channel Map:0 is already present
This is because of the code restructuring to move the PCM and control
instantiation into the codec drive probe, by the commit [
bcd96557bd0a:
ALSA: hda - Build PCMs and controls at codec driver probe]. Although
the commit above removed the calls of snd_hda_codec_build_pcms() and
*_build_controls() at the controller driver probe, the similar calls
in the reconfig were still left forgotten. This caused the
conflicting and duplicated PCMs and controls.
The fix is trivial: just remove these superfluous calls from
reconfig_codec().
Fixes:
bcd96557bd0a ('ALSA: hda - Build PCMs and controls at codec driver probe')
Reported-by: Jochen Henneberg <jh@henneberg-systemdesign.com>
Cc: <stable@vger.kernel.org> # v4.1+
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Daniel Vetter [Tue, 3 May 2016 08:33:01 +0000 (10:33 +0200)]
drm/i915: Bail out of pipe config compute loop on LPT
[ Upstream commit
2700818ac9f935d8590715eecd7e8cadbca552b6 ]
LPT is pch, so might run into the fdi bandwidth constraint (especially
since it has only 2 lanes). But right now we just force pipe_bpp back
to 24, resulting in a nice loop (which we bail out with a loud
WARN_ON). Fix this.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
References: https://bugs.freedesktop.org/show_bug.cgi?id=93477
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Tested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1462264381-7573-1-git-send-email-daniel.vetter@ffwll.ch
(cherry picked from commit
f58a1acc7e4a1f37d26124ce4c875c647fbcc61f)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Marek Szyprowski [Mon, 9 May 2016 16:31:47 +0000 (09:31 -0700)]
Input: max8997-haptic - fix NULL pointer dereference
[ Upstream commit
6ae645d5fa385f3787bf1723639cd907fe5865e7 ]
NULL pointer derefence happens when booting with DTB because the
platform data for haptic device is not set in supplied data from parent
MFD device.
The MFD device creates only platform data (from Device Tree) for itself,
not for haptic child.
Unable to handle kernel NULL pointer dereference at virtual address
0000009c
pgd =
c0004000
[
0000009c] *pgd=
00000000
Internal error: Oops: 5 [#1] PREEMPT SMP ARM
(max8997_haptic_probe) from [<
c03f9cec>] (platform_drv_probe+0x4c/0xb0)
(platform_drv_probe) from [<
c03f8440>] (driver_probe_device+0x214/0x2c0)
(driver_probe_device) from [<
c03f8598>] (__driver_attach+0xac/0xb0)
(__driver_attach) from [<
c03f67ac>] (bus_for_each_dev+0x68/0x9c)
(bus_for_each_dev) from [<
c03f7a38>] (bus_add_driver+0x1a0/0x218)
(bus_add_driver) from [<
c03f8db0>] (driver_register+0x78/0xf8)
(driver_register) from [<
c0101774>] (do_one_initcall+0x90/0x1d8)
(do_one_initcall) from [<
c0a00dbc>] (kernel_init_freeable+0x15c/0x1fc)
(kernel_init_freeable) from [<
c06bb5b4>] (kernel_init+0x8/0x114)
(kernel_init) from [<
c0107938>] (ret_from_fork+0x14/0x3c)
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: <stable@vger.kernel.org>
Fixes:
104594b01ce7 ("Input: add driver support for MAX8997-haptic")
[k.kozlowski: Write commit message, add CC-stable]
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Kaho Ng [Sun, 8 May 2016 16:27:49 +0000 (00:27 +0800)]
ALSA: hda - Fix white noise on Asus UX501VW headset
[ Upstream commit
2da2dc9ead232f25601404335cca13c0f722d41b ]
For reducing the noise from the headset output on ASUS UX501VW,
call the existing fixup, alc_fixup_headset_mode_alc668(), additionally.
Thread: https://bbs.archlinux.org/viewtopic.php?id=209554
Signed-off-by: Kaho Ng <ngkaho1234@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Bobi Mihalca [Wed, 23 Mar 2016 11:32:33 +0000 (13:32 +0200)]
ALSA: hda - Apply fix for white noise on Asus N550JV, too
[ Upstream commit
83a9efb5b8170b7cffef4f62656656e1d8ad2ccd ]
Apply the new fixup that is used for ASUS N750JV to another similar
model, N500JV, too, for reducing the headphone noise.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=115181
Signed-off-by: Bobi Mihalca <bobbymihalca@touchtech.ro>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Al Viro [Thu, 5 May 2016 20:25:35 +0000 (16:25 -0400)]
get_rock_ridge_filename(): handle malformed NM entries
[ Upstream commit
99d825822eade8d827a1817357cbf3f889a552d6 ]
Payloads of NM entries are not supposed to contain NUL. When we run
into such, only the part prior to the first NUL goes into the
concatenation (i.e. the directory entry name being encoded by a bunch
of NM entries). We do stop when the amount collected so far + the
claimed amount in the current NM entry exceed 254. So far, so good,
but what we return as the total length is the sum of *claimed*
sizes, not the actual amount collected. And that can grow pretty
large - not unlimited, since you'd need to put CE entries in
between to be able to get more than the maximum that could be
contained in one isofs directory entry / continuation chunk and
we are stop once we'd encountered 32 CEs, but you can get about 8Kb
easily. And that's what will be passed to readdir callback as the
name length. 8Kb __copy_to_user() from a buffer allocated by
__get_free_page()
Cc: stable@vger.kernel.org # 0.98pl6+ (yes, really)
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Dmitry V. Levin [Wed, 27 Apr 2016 01:56:11 +0000 (04:56 +0300)]
parisc: fix a bug when syscall number of tracee is __NR_Linux_syscalls
[ Upstream commit
f0b22d1bb2a37a665a969e95785c75a4f49d1499 ]
Do not load one entry beyond the end of the syscall table when the
syscall number of a traced process equals to __NR_Linux_syscalls.
Similar bug with regular processes was fixed by commit
3bb457af4fa8
("[PARISC] Fix bug when syscall nr is __NR_Linux_syscalls").
This bug was found by strace test suite.
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry V. Levin <ldv@altlinux.org>
Acked-by: Helge Deller <deller@gmx.de>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Chen Yu [Fri, 6 May 2016 03:33:39 +0000 (11:33 +0800)]
x86/tsc: Read all ratio bits from MSR_PLATFORM_INFO
[ Upstream commit
886123fb3a8656699dff40afa0573df359abeb18 ]
Currently we read the tsc radio: ratio = (MSR_PLATFORM_INFO >> 8) & 0x1f;
Thus we get bit 8-12 of MSR_PLATFORM_INFO, however according to the SDM
(35.5), the ratio bits are bit 8-15.
Ignoring the upper bits can result in an incorrect tsc ratio, which causes the
TSC calibration and the Local APIC timer frequency to be incorrect.
Fix this problem by masking 0xff instead.
[ tglx: Massaged changelog ]
Fixes:
7da7c1561366 "x86, tsc: Add static (MSR) TSC calibration on Intel Atom SoCs"
Signed-off-by: Chen Yu <yu.c.chen@intel.com>
Cc: "Rafael J. Wysocki" <rafael@kernel.org>
Cc: stable@vger.kernel.org
Cc: Bin Gao <bin.gao@intel.com>
Cc: Len Brown <lenb@kernel.org>
Link: http://lkml.kernel.org/r/1462505619-5516-1-git-send-email-yu.c.chen@intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Hugh Dickins [Thu, 5 May 2016 23:22:15 +0000 (16:22 -0700)]
mm, cma: prevent nr_isolated_* counters from going negative
[ Upstream commit
14af4a5e9b26ad251f81c174e8a43f3e179434a5 ]
/proc/sys/vm/stat_refresh warns nr_isolated_anon and nr_isolated_file go
increasingly negative under compaction: which would add delay when
should be none, or no delay when should delay. The bug in compaction
was due to a recent mmotm patch, but much older instance of the bug was
also noticed in isolate_migratepages_range() which is used for CMA and
gigantic hugepage allocations.
The bug is caused by putback_movable_pages() in an error path
decrementing the isolated counters without them being previously
incremented by acct_isolated(). Fix isolate_migratepages_range() by
removing the error-path putback, thus reaching acct_isolated() with
migratepages still isolated, and leaving putback to caller like most
other places do.
Fixes:
edc2ca612496 ("mm, compaction: move pageblock checks up from isolate_migratepages_range()")
[vbabka@suse.cz: expanded the changelog]
Signed-off-by: Hugh Dickins <hughd@google.com>
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Acked-by: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Arindam Nath [Wed, 4 May 2016 18:09:59 +0000 (23:39 +0530)]
drm/radeon: fix DP link training issue with second 4K monitor
[ Upstream commit
1a738347df2ee4977459a8776fe2c62196bdcb1b ]
There is an issue observed when we hotplug a second DP
4K monitor to the system. Sometimes, the link training
fails for the second monitor after HPD interrupt
generation.
The issue happens when some queued or deferred transactions
are already present on the AUX channel when we initiate
a new transcation to (say) get DPCD or during link training.
We set AUX_IGNORE_HPD_DISCON bit in the AUX_CONTROL
register so that we can ignore any such deferred
transactions when a new AUX transaction is initiated.
Signed-off-by: Arindam Nath <arindam.nath@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Eric W. Biederman [Thu, 5 May 2016 14:29:29 +0000 (09:29 -0500)]
propogate_mnt: Handle the first propogated copy being a slave
[ Upstream commit
5ec0811d30378ae104f250bfc9b3640242d81e3f ]
When the first propgated copy was a slave the following oops would result:
> BUG: unable to handle kernel NULL pointer dereference at
0000000000000010
> IP: [<
ffffffff811fba4e>] propagate_one+0xbe/0x1c0
> PGD
bacd4067 PUD
bac66067 PMD 0
> Oops: 0000 [#1] SMP
> Modules linked in:
> CPU: 1 PID: 824 Comm: mount Not tainted 4.6.0-rc5userns+ #1523
> Hardware name: Bochs Bochs, BIOS Bochs 01/01/2007
> task:
ffff8800bb0a8000 ti:
ffff8800bac3c000 task.ti:
ffff8800bac3c000
> RIP: 0010:[<
ffffffff811fba4e>] [<
ffffffff811fba4e>] propagate_one+0xbe/0x1c0
> RSP: 0018:
ffff8800bac3fd38 EFLAGS:
00010283
> RAX:
0000000000000000 RBX:
ffff8800bb77ec00 RCX:
0000000000000010
> RDX:
0000000000000000 RSI:
ffff8800bb58c000 RDI:
ffff8800bb58c480
> RBP:
ffff8800bac3fd48 R08:
0000000000000001 R09:
0000000000000000
> R10:
0000000000001ca1 R11:
0000000000001c9d R12:
0000000000000000
> R13:
ffff8800ba713800 R14:
ffff8800bac3fda0 R15:
ffff8800bb77ec00
> FS:
00007f3c0cd9b7e0(0000) GS:
ffff8800bfb00000(0000) knlGS:
0000000000000000
> CS: 0010 DS: 0000 ES: 0000 CR0:
0000000080050033
> CR2:
0000000000000010 CR3:
00000000bb79d000 CR4:
00000000000006e0
> Stack:
>
ffff8800bb77ec00 0000000000000000 ffff8800bac3fd88 ffffffff811fbf85
>
ffff8800bac3fd98 ffff8800bb77f080 ffff8800ba713800 ffff8800bb262b40
>
0000000000000000 0000000000000000 ffff8800bac3fdd8 ffffffff811f1da0
> Call Trace:
> [<
ffffffff811fbf85>] propagate_mnt+0x105/0x140
> [<
ffffffff811f1da0>] attach_recursive_mnt+0x120/0x1e0
> [<
ffffffff811f1ec3>] graft_tree+0x63/0x70
> [<
ffffffff811f1f6b>] do_add_mount+0x9b/0x100
> [<
ffffffff811f2c1a>] do_mount+0x2aa/0xdf0
> [<
ffffffff8117efbe>] ? strndup_user+0x4e/0x70
> [<
ffffffff811f3a45>] SyS_mount+0x75/0xc0
> [<
ffffffff8100242b>] do_syscall_64+0x4b/0xa0
> [<
ffffffff81988f3c>] entry_SYSCALL64_slow_path+0x25/0x25
> Code: 00 00 75 ec 48 89 0d 02 22 22 01 8b 89 10 01 00 00 48 89 05 fd 21 22 01 39 8e 10 01 00 00 0f 84 e0 00 00 00 48 8b 80 d8 00 00 00 <48> 8b 50 10 48 89 05 df 21 22 01 48 89 15 d0 21 22 01 8b 53 30
> RIP [<
ffffffff811fba4e>] propagate_one+0xbe/0x1c0
> RSP <
ffff8800bac3fd38>
> CR2:
0000000000000010
> ---[ end trace
2725ecd95164f217 ]---
This oops happens with the namespace_sem held and can be triggered by
non-root users. An all around not pleasant experience.
To avoid this scenario when finding the appropriate source mount to
copy stop the walk up the mnt_master chain when the first source mount
is encountered.
Further rewrite the walk up the last_source mnt_master chain so that
it is clear what is going on.
The reason why the first source mount is special is that it it's
mnt_parent is not a mount in the dest_mnt propagation tree, and as
such termination conditions based up on the dest_mnt mount propgation
tree do not make sense.
To avoid other kinds of confusion last_dest is not changed when
computing last_source. last_dest is only used once in propagate_one
and that is above the point of the code being modified, so changing
the global variable is meaningless and confusing.
Cc: stable@vger.kernel.org
fixes:
f2ebb3a921c1ca1e2ddd9242e95a1989a50c4c68 ("smarter propagate_mnt()")
Reported-by: Tycho Andersen <tycho.andersen@canonical.com>
Reviewed-by: Seth Forshee <seth.forshee@canonical.com>
Tested-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Maxim Patlasov [Tue, 16 Feb 2016 19:45:33 +0000 (11:45 -0800)]
fs/pnode.c: treat zero mnt_group_id-s as unequal
[ Upstream commit
7ae8fd0351f912b075149a1e03a017be8b903b9a ]
propagate_one(m) calculates "type" argument for copy_tree() like this:
> if (m->mnt_group_id == last_dest->mnt_group_id) {
> type = CL_MAKE_SHARED;
> } else {
> type = CL_SLAVE;
> if (IS_MNT_SHARED(m))
> type |= CL_MAKE_SHARED;
> }
The "type" argument then governs clone_mnt() behavior with respect to flags
and mnt_master of new mount. When we iterate through a slave group, it is
possible that both current "m" and "last_dest" are not shared (although,
both are slaves, i.e. have non-NULL mnt_master-s). Then the comparison
above erroneously makes new mount shared and sets its mnt_master to
last_source->mnt_master. The patch fixes the problem by handling zero
mnt_group_id-s as though they are unequal.
The similar problem exists in the implementation of "else" clause above
when we have to ascend upward in the master/slave tree by calling:
> last_source = last_source->mnt_master;
> last_dest = last_source->mnt_parent;
proper number of times. The last step is governed by
"n->mnt_group_id != last_dest->mnt_group_id" condition that may lie if
both are zero. The patch fixes this case in the same way as the former one.
[AV: don't open-code an obvious helper...]
Signed-off-by: Maxim Patlasov <mpatlasov@virtuozzo.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Wang YanQing [Thu, 5 May 2016 13:14:21 +0000 (14:14 +0100)]
x86/sysfb_efi: Fix valid BAR address range check
[ Upstream commit
c10fcb14c7afd6688c7b197a814358fecf244222 ]
The code for checking whether a BAR address range is valid will break
out of the loop when a start address of 0x0 is encountered.
This behaviour is wrong since by breaking out of the loop we may miss
the BAR that describes the EFI frame buffer in a later iteration.
Because of this bug I can't use video=efifb: boot parameter to get
efifb on my new ThinkPad E550 for my old linux system hard disk with
3.10 kernel. In 3.10, efifb is the only choice due to DRM/I915 not
supporting the GPU.
This patch also add a trivial optimization to break out after we find
the frame buffer address range without testing later BARs.
Signed-off-by: Wang YanQing <udknight@gmail.com>
[ Rewrote changelog. ]
Signed-off-by: Matt Fleming <matt@codeblueprint.co.uk>
Reviewed-by: Peter Jones <pjones@redhat.com>
Cc: <stable@vger.kernel.org>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: David Herrmann <dh.herrmann@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: linux-efi@vger.kernel.org
Link: http://lkml.kernel.org/r/1462454061-21561-2-git-send-email-matt@codeblueprint.co.uk
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Herbert Xu [Wed, 4 May 2016 09:52:56 +0000 (17:52 +0800)]
crypto: hash - Fix page length clamping in hash walk
[ Upstream commit
13f4bb78cf6a312bbdec367ba3da044b09bf0e29 ]
The crypto hash walk code is broken when supplied with an offset
greater than or equal to PAGE_SIZE. This patch fixes it by adjusting
walk->pg and walk->offset when this happens.
Cc: <stable@vger.kernel.org>
Reported-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Prarit Bhargava [Wed, 4 May 2016 05:48:56 +0000 (13:48 +0800)]
ACPICA: Dispatcher: Update thread ID for recursive method calls
[ Upstream commit
93d68841a23a5779cef6fb9aa0ef32e7c5bd00da ]
ACPICA commit
7a3bd2d962f221809f25ddb826c9e551b916eb25
Set the mutex owner thread ID.
Original patch from: Prarit Bhargava <prarit@redhat.com>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=115121
Link: https://github.com/acpica/acpica/commit/7a3bd2d9
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Tested-by: Andy Lutomirski <luto@kernel.org> # On a Dell XPS 13 9350
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Matt Fleming [Tue, 3 May 2016 19:29:39 +0000 (20:29 +0100)]
MAINTAINERS: Remove asterisk from EFI directory names
[ Upstream commit
e8dfe6d8f6762d515fcd4f30577f7bfcf7659887 ]
Mark reported that having asterisks on the end of directory names
confuses get_maintainer.pl when it encounters subdirectories, and that
my name does not appear when run on drivers/firmware/efi/libstub.
Reported-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Matt Fleming <matt@codeblueprint.co.uk>
Cc: <stable@vger.kernel.org>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-efi@vger.kernel.org
Link: http://lkml.kernel.org/r/1462303781-8686-2-git-send-email-matt@codeblueprint.co.uk
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Alex Deucher [Mon, 2 May 2016 22:53:27 +0000 (18:53 -0400)]
drm/radeon: make sure vertical front porch is at least 1
[ Upstream commit
3104b8128d4d646a574ed9d5b17c7d10752cd70b ]
hw doesn't like a 0 value.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Chunyu Hu [Tue, 3 May 2016 11:34:34 +0000 (19:34 +0800)]
tracing: Don't display trigger file for events that can't be enabled
[ Upstream commit
854145e0a8e9a05f7366d240e2f99d9c1ca6d6dd ]
Currently register functions for events will be called
through the 'reg' field of event class directly without
any check when seting up triggers.
Triggers for events that don't support register through
debug fs (events under events/ftrace are for trace-cmd to
read event format, and most of them don't have a register
function except events/ftrace/functionx) can't be enabled
at all, and an oops will be hit when setting up trigger
for those events, so just not creating them is an easy way
to avoid the oops.
Link: http://lkml.kernel.org/r/1462275274-3911-1-git-send-email-chuhu@redhat.com
Cc: stable@vger.kernel.org # 3.14+
Fixes:
85f2b08268c01 ("tracing: Add basic event trigger framework")
Signed-off-by: Chunyu Hu <chuhu@redhat.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Linus Torvalds [Mon, 2 May 2016 19:46:42 +0000 (12:46 -0700)]
Minimal fix-up of bad hashing behavior of hash_64()
[ Upstream commit
689de1d6ca95b3b5bd8ee446863bf81a4883ea25 ]
This is a fairly minimal fixup to the horribly bad behavior of hash_64()
with certain input patterns.
In particular, because the multiplicative value used for the 64-bit hash
was intentionally bit-sparse (so that the multiply could be done with
shifts and adds on architectures without hardware multipliers), some
bits did not get spread out very much. In particular, certain fairly
common bit ranges in the input (roughly bits 12-20: commonly with the
most information in them when you hash things like byte offsets in files
or memory that have block factors that mean that the low bits are often
zero) would not necessarily show up much in the result.
There's a bigger patch-series brewing to fix up things more completely,
but this is the fairly minimal fix for the 64-bit hashing problem. It
simply picks a much better constant multiplier, spreading the bits out a
lot better.
NOTE! For 32-bit architectures, the bad old hash_64() remains the same
for now, since 64-bit multiplies are expensive. The bigger hashing
cleanup will replace the 32-bit case with something better.
The new constants were picked by George Spelvin who wrote that bigger
cleanup series. I just picked out the constants and part of the comment
from that series.
Cc: stable@vger.kernel.org
Cc: George Spelvin <linux@horizon.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Anton Blanchard [Fri, 29 Apr 2016 22:29:27 +0000 (08:29 +1000)]
powerpc: Fix bad inline asm constraint in create_zero_mask()
[ Upstream commit
b4c112114aab9aff5ed4568ca5e662bb02cdfe74 ]
In create_zero_mask() we have:
addi %1,%2,-1
andc %1,%1,%2
popcntd %0,%1
using the "r" constraint for %2. r0 is a valid register in the "r" set,
but addi X,r0,X turns it into an li:
li r7,-1
andc r7,r7,r0
popcntd r4,r7
Fix this by using the "b" constraint, for which r0 is not a valid
register.
This was found with a kernel build using gcc trunk, narrowed down to
when -frename-registers was enabled at -O2. It is just luck however
that we aren't seeing this on older toolchains.
Thanks to Segher for working with me to find this issue.
Cc: stable@vger.kernel.org
Fixes:
d0cebfa650a0 ("powerpc: word-at-a-time optimization for 64-bit Little Endian")
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
K. Y. Srinivasan [Sat, 2 Apr 2016 23:17:38 +0000 (16:17 -0700)]
Drivers: hv: vmbus: Fix signaling logic in hv_need_to_signal_on_read()
[ Upstream commit
1db488d12894f1936360779d6ab2aede3dd7f06a ]
On the consumer side, we have interrupt driven flow management of the
producer. It is sufficient to base the signaling decision on the
amount of space that is available to write after the read is complete.
The current code samples the previous available space and uses this
in making the signaling decision. This state can be stale and is
unnecessary. Since the state can be stale, we end up not signaling
the host (when we should) and this can result in a hang. Fix this
problem by removing the unnecessary check. I would like to thank
Arseney Romanenko <arseneyr@microsoft.com> for pointing out this issue.
Also, issue a full memory barrier before making the signaling descision
to correctly deal with potential reordering of the write (read index)
followed by the read of pending_sz.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Tested-by: Dexuan Cui <decui@microsoft.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Christopher Oo [Wed, 5 Aug 2015 07:52:40 +0000 (00:52 -0700)]
Drivers: hv_vmbus: Fix signal to host condition
[ Upstream commit
a5cca686ce0ef4909deaee4ed46dd991e3a9ece4 ]
Fixes a bug where previously hv_ringbuffer_read would pass in the old
number of bytes available to read instead of the expected old read index
when calculating when to signal to the host that the ringbuffer is empty.
Since the previous write size is already saved, also changes the
hv_need_to_signal_on_read to use the previously read value rather than
recalculating it.
Signed-off-by: Christopher Oo <t-chriso@microsoft.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Vitaly Kuznetsov [Tue, 15 Dec 2015 03:01:57 +0000 (19:01 -0800)]
Drivers: hv: ring_buffer.c: fix comment style
[ Upstream commit
822f18d4d3e9d4efb4996bbe562d0f99ab82d7dd ]
Convert 6+-string comments repeating function names to normal kernel-style
comments and fix a couple of other comment style issues. No textual or
functional changes intended.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Al Viro [Wed, 27 Apr 2016 05:11:55 +0000 (01:11 -0400)]
atomic_open(): fix the handling of create_error
[ Upstream commit
10c64cea04d3c75c306b3f990586ffb343b63287 ]
* if we have a hashed negative dentry and either CREAT|EXCL on
r/o filesystem, or CREAT|TRUNC on r/o filesystem, or CREAT|EXCL
with failing may_o_create(), we should fail with EROFS or the
error may_o_create() has returned, but not ENOENT. Which is what
the current code ends up returning.
* if we have CREAT|TRUNC hitting a regular file on a read-only
filesystem, we can't fail with EROFS here. At the very least,
not until we'd done follow_managed() - we might have a writable
file (or a device, for that matter) bound on top of that one.
Moreover, the code downstream will see that O_TRUNC and attempt
to grab the write access (*after* following possible mount), so
if we really should fail with EROFS, it will happen. No need
to do that inside atomic_open().
The real logics is much simpler than what the current code is
trying to do - if we decided to go for simple lookup, ended
up with a negative dentry *and* had create_error set, fail with
create_error. No matter whether we'd got that negative dentry
from lookup_real() or had found it in dcache.
Cc: stable@vger.kernel.org # v3.6+
Acked-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Tony Luck [Fri, 29 Apr 2016 13:42:25 +0000 (15:42 +0200)]
EDAC: i7core, sb_edac: Don't return NOTIFY_BAD from mce_decoder callback
[ Upstream commit
c4fc1956fa31003bfbe4f597e359d751568e2954 ]
Both of these drivers can return NOTIFY_BAD, but this terminates
processing other callbacks that were registered later on the chain.
Since the driver did nothing to log the error it seems wrong to prevent
other interested parties from seeing it. E.g. neither of them had even
bothered to check the type of the error to see if it was a memory error
before the return NOTIFY_BAD.
Signed-off-by: Tony Luck <tony.luck@intel.com>
Acked-by: Aristeu Rozanski <aris@redhat.com>
Acked-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Cc: <stable@vger.kernel.org>
Link: http://lkml.kernel.org/r/72937355dd92318d2630979666063f8a2853495b.1461864507.git.tony.luck@intel.com
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Takashi Iwai [Fri, 29 Apr 2016 09:20:15 +0000 (11:20 +0200)]
ALSA: usb-audio: Quirk for yet another Phoenix Audio devices (v2)
[ Upstream commit
2d2c038a9999f423e820d89db2b5d7774b67ba49 ]
Phoenix Audio MT202pcs (1de7:0114) and MT202exe (1de7:0013) need the
same workaround as TMX320 for avoiding the firmware bug. It fixes the
frequent error about the sample rate inquiries and the slow device
probe as consequence.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=117321
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Naoya Horiguchi [Thu, 6 Aug 2015 22:47:08 +0000 (15:47 -0700)]
mm: check __PG_HWPOISON separately from PAGE_FLAGS_CHECK_AT_*
[ Upstream commit
f4c18e6f7b5bbb5b528b3334115806b0d76f50f9 ]
The race condition addressed in commit
add05cecef80 ("mm: soft-offline:
don't free target page in successful page migration") was not closed
completely, because that can happen not only for soft-offline, but also
for hard-offline. Consider that a slab page is about to be freed into
buddy pool, and then an uncorrected memory error hits the page just
after entering __free_one_page(), then VM_BUG_ON_PAGE(page->flags &
PAGE_FLAGS_CHECK_AT_PREP) is triggered, despite the fact that it's not
necessary because the data on the affected page is not consumed.
To solve it, this patch drops __PG_HWPOISON from page flag checks at
allocation/free time. I think it's justified because __PG_HWPOISON
flags is defined to prevent the page from being reused, and setting it
outside the page's alloc-free cycle is a designed behavior (not a bug.)
For recent months, I was annoyed about BUG_ON when soft-offlined page
remains on lru cache list for a while, which is avoided by calling
put_page() instead of putback_lru_page() in page migration's success
path. This means that this patch reverts a major change from commit
add05cecef80 about the new refcounting rule of soft-offlined pages, so
"reuse window" revives. This will be closed by a subsequent patch.
Signed-off-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Dean Nelson <dnelson@redhat.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: "Kirill A. Shutemov" <kirill@shutemov.name>
Cc: Hugh Dickins <hughd@google.com>
Cc: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Naoya Horiguchi [Wed, 24 Jun 2015 23:56:50 +0000 (16:56 -0700)]
mm: soft-offline: don't free target page in successful page migration
[ Upstream commit
add05cecef803f3372c5fc1d2a964171872daf9f ]
Stress testing showed that soft offline events for a process iterating
"mmap-pagefault-munmap" loop can trigger
VM_BUG_ON(PAGE_FLAGS_CHECK_AT_PREP) in __free_one_page():
Soft offlining page 0x70fe1 at 0x70100008d000
Soft offlining page 0x705fb at 0x70300008d000
page:
ffffea0001c3f840 count:0 mapcount:0 mapping: (null) index:0x2
flags: 0x1fffff80800000(hwpoison)
page dumped because: VM_BUG_ON_PAGE(page->flags & ((1 << 25) - 1))
------------[ cut here ]------------
kernel BUG at /src/linux-dev/mm/page_alloc.c:585!
invalid opcode: 0000 [#1] SMP DEBUG_PAGEALLOC
Modules linked in: cfg80211 rfkill crc32c_intel microcode ppdev parport_pc pcspkr serio_raw virtio_balloon parport i2c_piix4 virtio_blk virtio_net ata_generic pata_acpi floppy
CPU: 3 PID: 1779 Comm: test_base_madv_ Not tainted 4.0.0-v4.0-150511-1451-00009-g82360a3730e6 #139
RIP: free_pcppages_bulk+0x52a/0x6f0
Call Trace:
drain_pages_zone+0x3d/0x50
drain_local_pages+0x1d/0x30
on_each_cpu_mask+0x46/0x80
drain_all_pages+0x14b/0x1e0
soft_offline_page+0x432/0x6e0
SyS_madvise+0x73c/0x780
system_call_fastpath+0x12/0x17
Code: ff 89 45 b4 48 8b 45 c0 48 83 b8 a8 00 00 00 00 0f 85 e3 fb ff ff 0f 1f 00 0f 0b 48 8b 7d 90 48 c7 c6 e8 95 a6 81 e8 e6 32 02 00 <0f> 0b 8b 45 cc 49 89 47 30 41 8b 47 18 83 f8 ff 0f 85 10 ff ff
RIP [<
ffffffff811a806a>] free_pcppages_bulk+0x52a/0x6f0
RSP <
ffff88007a117d28>
---[ end trace
53926436e76d1f35 ]---
When soft offline successfully migrates page, the source page is supposed
to be freed. But there is a race condition where a source page looks
isolated (i.e. the refcount is 0 and the PageHWPoison is set) but
somewhat linked to pcplist. Then another soft offline event calls
drain_all_pages() and tries to free such hwpoisoned page, which is
forbidden.
This odd page state seems to happen due to the race between put_page() in
putback_lru_page() and __pagevec_lru_add_fn(). But I don't want to play
with tweaking drain code as done in commit
9ab3b598d2df "mm: hwpoison:
drop lru_add_drain_all() in __soft_offline_page()", or to change page
freeing code for this soft offline's purpose.
Instead, let's think about the difference between hard offline and soft
offline. There is an interesting difference in how to isolate the in-use
page between these, that is, hard offline marks PageHWPoison of the target
page at first, and doesn't free it by keeping its refcount 1. OTOH, soft
offline tries to free the target page then marks PageHWPoison. This
difference might be the source of complexity and result in bugs like the
above. So making soft offline isolate with keeping refcount can be a
solution for this problem.
We can pass to page migration code the "reason" which shows the caller, so
let's use this more to avoid calling putback_lru_page() when called from
soft offline, which effectively does the isolation for soft offline. With
this change, target pages of soft offline never be reused without changing
migratetype, so this patch also removes the related code.
Signed-off-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: "Kirill A. Shutemov" <kirill@shutemov.name>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Minchan Kim [Thu, 28 Apr 2016 23:18:38 +0000 (16:18 -0700)]
mm: vmscan: reclaim highmem zone if buffer_heads is over limit
[ Upstream commit
7bf52fb891b64b8d61caf0b82060adb9db761aec ]
We have been reclaimed highmem zone if buffer_heads is over limit but
commit
6b4f7799c6a5 ("mm: vmscan: invoke slab shrinkers from
shrink_zone()") changed the behavior so it doesn't reclaim highmem zone
although buffer_heads is over the limit. This patch restores the logic.
Fixes:
6b4f7799c6a5 ("mm: vmscan: invoke slab shrinkers from shrink_zone()")
Signed-off-by: Minchan Kim <minchan@kernel.org>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Konstantin Khlebnikov [Thu, 28 Apr 2016 23:18:32 +0000 (16:18 -0700)]
mm/huge_memory: replace VM_NO_THP VM_BUG_ON with actual VMA check
[ Upstream commit
3486b85a29c1741db99d0c522211c82d2b7a56d0 ]
Khugepaged detects own VMAs by checking vm_file and vm_ops but this way
it cannot distinguish private /dev/zero mappings from other special
mappings like /dev/hpet which has no vm_ops and popultes PTEs in mmap.
This fixes false-positive VM_BUG_ON and prevents installing THP where
they are not expected.
Link: http://lkml.kernel.org/r/CACT4Y+ZmuZMV5CjSFOeXviwQdABAgT7T+StKfTqan9YDtgEi5g@mail.gmail.com
Fixes:
78f11a255749 ("mm: thp: fix /dev/zero MAP_PRIVATE and vm_flags cleanups")
Signed-off-by: Konstantin Khlebnikov <koct9i@gmail.com>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Jason Gunthorpe [Mon, 11 Apr 2016 01:13:13 +0000 (19:13 -0600)]
IB/security: Restrict use of the write() interface
[ Upstream commit
e6bd18f57aad1a2d1ef40e646d03ed0f2515c9e3 ]
The drivers/infiniband stack uses write() as a replacement for
bi-directional ioctl(). This is not safe. There are ways to
trigger write calls that result in the return structure that
is normally written to user space being shunted off to user
specified kernel memory instead.
For the immediate repair, detect and deny suspicious accesses to
the write API.
For long term, update the user space libraries and the kernel API
to something that doesn't present the same security vulnerabilities
(likely a structured ioctl() interface).
The impacted uAPI interfaces are generally only available if
hardware from drivers/infiniband is installed in the system.
Reported-by: Jann Horn <jann@thejh.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
[ Expanded check to all known write() entry points ]
Cc: stable@vger.kernel.org
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
James Morse [Tue, 26 Apr 2016 11:15:01 +0000 (12:15 +0100)]
ARM: cpuidle: Pass on arm_cpuidle_suspend()'s return value
[ Upstream commit
625fe4f8ffc1b915248558481bb94249f6bd411c ]
arm_cpuidle_suspend() may return -EOPNOTSUPP, or any value returned
by the cpu_ops/cpuidle_ops suspend call. arm_enter_idle_state() doesn't
update 'ret' with this value, meaning we always signal success to
cpuidle_enter_state(), causing it to update the usage counters as if we
succeeded.
Fixes:
191de17aa3c1 ("ARM64: cpuidle: Replace cpu_suspend by the common ARM/ARM64 function")
Signed-off-by: James Morse <james.morse@arm.com>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: 4.1+ <stable@vger.kernel.org> # 4.1+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Sascha Hauer [Wed, 20 Apr 2016 13:34:31 +0000 (13:34 +0000)]
ARM: SoCFPGA: Fix secondary CPU startup in thumb2 kernel
[ Upstream commit
5616f36713ea77f57ae908bf2fef641364403c9f ]
The secondary CPU starts up in ARM mode. When the kernel is compiled in
thumb2 mode we have to explicitly compile the secondary startup
trampoline in ARM mode, otherwise the CPU will go to Nirvana.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reported-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Suggested-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: stable@vger.kernel.org
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Vitaly Prosyak [Thu, 14 Apr 2016 17:34:03 +0000 (13:34 -0400)]
drm/radeon: fix vertical bars appear on monitor (v2)
[ Upstream commit
5d5b7803c49bbb01bdf4c6e95e8314d0515b9484 ]
When crtc/timing is disabled on boot the dig block
should be stopped in order ignore timing from crtc,
reset the steering fifo otherwise we get display
corruption or hung in dp sst mode.
v2: agd: fix coding style
Signed-off-by: Vitaly Prosyak <vitaly.prosyak@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Ville Syrjälä [Wed, 20 Apr 2016 13:43:56 +0000 (16:43 +0300)]
drm/i915: Make RPS EI/thresholds multiple of 25 on SNB-BDW
[ Upstream commit
4ea3959018d09edfa36a9e7b5ccdbd4ec4b99e49 ]
Somehow my SNB GT1 (Dell XPS 8300) gets very unhappy around
GPU hangs if the RPS EI/thresholds aren't suitably aligned.
It seems like scheduling/timer interupts stop working somehow
and things get stuck eg. in usleep_range().
I bisected the problem down to
commit
8a5864377b12 ("drm/i915/skl: Restructured the gen6_set_rps_thresholds function")
I observed that before all the values were at least multiples of 25,
but afterwards they are not. And rounding things up to the next multiple
of 25 does seem to help, so lets' do that. I also tried roundup(..., 5)
but that wasn't sufficient. Also I have no idea if we might need this sort of
thing on gen9+ as well.
These are the original EI/thresholds:
LOW_POWER
GEN6_RP_UP_EI 12500
GEN6_RP_UP_THRESHOLD 11800
GEN6_RP_DOWN_EI 25000
GEN6_RP_DOWN_THRESHOLD 21250
BETWEEN
GEN6_RP_UP_EI 10250
GEN6_RP_UP_THRESHOLD 9225
GEN6_RP_DOWN_EI 25000
GEN6_RP_DOWN_THRESHOLD 18750
HIGH_POWER
GEN6_RP_UP_EI 8000
GEN6_RP_UP_THRESHOLD 6800
GEN6_RP_DOWN_EI 25000
GEN6_RP_DOWN_THRESHOLD 15000
These are after
8a5864377b12:
LOW_POWER
GEN6_RP_UP_EI 12500
GEN6_RP_UP_THRESHOLD 11875
GEN6_RP_DOWN_EI 25000
GEN6_RP_DOWN_THRESHOLD 21250
BETWEEN
GEN6_RP_UP_EI 10156
GEN6_RP_UP_THRESHOLD 9140
GEN6_RP_DOWN_EI 25000
GEN6_RP_DOWN_THRESHOLD 18750
HIGH_POWER
GEN6_RP_UP_EI 7812
GEN6_RP_UP_THRESHOLD 6640
GEN6_RP_DOWN_EI 25000
GEN6_RP_DOWN_THRESHOLD 15000
And these are what we have after this patch:
LOW_POWER
GEN6_RP_UP_EI 12500
GEN6_RP_UP_THRESHOLD 11875
GEN6_RP_DOWN_EI 25000
GEN6_RP_DOWN_THRESHOLD 21250
BETWEEN
GEN6_RP_UP_EI 10175
GEN6_RP_UP_THRESHOLD 9150
GEN6_RP_DOWN_EI 25000
GEN6_RP_DOWN_THRESHOLD 18750
HIGH_POWER
GEN6_RP_UP_EI 7825
GEN6_RP_UP_THRESHOLD 6650
GEN6_RP_DOWN_EI 25000
GEN6_RP_DOWN_THRESHOLD 15000
Cc: stable@vger.kernel.org
Cc: Akash Goel <akash.goel@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Testcase: igt/kms_pipe_crc_basic/hang-read-crc-pipe-B
Fixes:
8a5864377b12 ("drm/i915/skl: Restructured the gen6_set_rps_thresholds function")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461159836-9108-1-git-send-email-ville.syrjala@linux.intel.com
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
(cherry picked from commit
8a292d016d1cc4938ff14b4df25328230b08a408)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Imre Deak [Mon, 18 Apr 2016 07:04:21 +0000 (10:04 +0300)]
drm/i915/ddi: Fix eDP VDD handling during booting and suspend/resume
[ Upstream commit
5eaa60c7109b40f17ac81090bc8b90482da76cd1 ]
The driver's VDD on/off logic assumes that whenever the VDD is on we
also hold an AUX power domain reference. Since BIOS can leave the VDD on
during booting and resuming and on DDI platforms we won't take a
corresponding power reference, the above assumption won't hold on those
platforms and an eventual delayed VDD off work will do an extraneous AUX
power domain put resulting in a refcount underflow. Fix this the same
way we did this for non-DDI DP encoders:
commit
6d93c0c41760c0 ("drm/i915: fix VDD state tracking after system
resume")
At the same time call the DP encoder suspend handler the same way as the
non-DDI DP encoders do to flush any pending VDD off work. Leaving the
work running may cause a HW access where we don't expect this (at a point
where power domains are suspended already).
While at it remove an unnecessary function call indirection.
This fixed for me AUX refcount underflow problems on BXT during
suspend/resume.
CC: Ville Syrjälä <ville.syrjala@linux.intel.com>
CC: stable@vger.kernel.org
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460963062-13211-4-git-send-email-imre.deak@intel.com
(cherry picked from commit
bf93ba67e9c05882f05b7ca2d773cfc8bf462c2a)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Michael Neuling [Fri, 22 Apr 2016 04:57:48 +0000 (14:57 +1000)]
cxl: Keep IRQ mappings on context teardown
[ Upstream commit
d6776bba44d9752f6cdf640046070e71ee4bba7b ]
Keep IRQ mappings on context teardown. This won't leak IRQs as if we
allocate the mapping again, the generic code will give the same
mapping used last time.
Doing this works around a race in the generic code. Masking the
interrupt introduces a race which can crash the kernel or result in
IRQ that is never EOIed. The lost of EOI results in all subsequent
mappings to the same HW IRQ never receiving an interrupt.
We've seen this race with cxl test cases which are doing heavy context
startup and teardown at the same time as heavy interrupt load.
A fix to the generic code is being investigated also.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Cc: stable@vger.kernel.org # 3.8
Tested-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Tested-by: Vaibhav Jain <vaibhav@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Lyude [Wed, 13 Apr 2016 20:50:18 +0000 (16:50 -0400)]
drm/dp/mst: Restore primary hub guid on resume
[ Upstream commit
9dc0487d96a0396367a1451b31873482080b527f ]
Some hubs are forgetful, and end up forgetting whatever GUID we set
previously after we do a suspend/resume cycle. This can lead to
hotplugging breaking (along with probably other things) since the hub
will start sending connection notifications with the wrong GUID. As
such, we need to check on resume whether or not the GUID the hub is
giving us is valid.
Signed-off-by: Lyude <cpaul@redhat.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1460580618-7421-1-git-send-email-cpaul@redhat.com
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
cpaul@redhat.com [Fri, 22 Apr 2016 20:08:46 +0000 (16:08 -0400)]
drm/dp/mst: Get validated port ref in drm_dp_update_payload_part1()
[ Upstream commit
263efde31f97c498e1ebad30e4d2906609d7ad6b ]
We can thank KASAN for finding this, otherwise I probably would have spent
hours on it. This fixes a somewhat harder to trigger kernel panic, occuring
while enabling MST where the port we were currently updating the payload on
would have all of it's refs dropped before we finished what we were doing:
==================================================================
BUG: KASAN: use-after-free in drm_dp_update_payload_part1+0xb3f/0xdb0 [drm_kms_helper] at addr
ffff8800d29de018
Read of size 4 by task Xorg/973
=============================================================================
BUG kmalloc-2048 (Tainted: G B W ): kasan: bad access detected
-----------------------------------------------------------------------------
INFO: Allocated in drm_dp_add_port+0x1aa/0x1ed0 [drm_kms_helper] age=16477 cpu=0 pid=2175
___slab_alloc+0x472/0x490
__slab_alloc+0x20/0x40
kmem_cache_alloc_trace+0x151/0x190
drm_dp_add_port+0x1aa/0x1ed0 [drm_kms_helper]
drm_dp_send_link_address+0x526/0x960 [drm_kms_helper]
drm_dp_check_and_send_link_address+0x1ac/0x210 [drm_kms_helper]
drm_dp_mst_link_probe_work+0x77/0xd0 [drm_kms_helper]
process_one_work+0x562/0x1350
worker_thread+0xd9/0x1390
kthread+0x1c5/0x260
ret_from_fork+0x22/0x40
INFO: Freed in drm_dp_free_mst_port+0x50/0x60 [drm_kms_helper] age=7521 cpu=0 pid=2175
__slab_free+0x17f/0x2d0
kfree+0x169/0x180
drm_dp_free_mst_port+0x50/0x60 [drm_kms_helper]
drm_dp_destroy_connector_work+0x2b8/0x490 [drm_kms_helper]
process_one_work+0x562/0x1350
worker_thread+0xd9/0x1390
kthread+0x1c5/0x260
ret_from_fork+0x22/0x40
which on this T460s, would eventually lead to kernel panics in somewhat
random places later in intel_mst_enable_dp() if we got lucky enough.
Signed-off-by: Lyude <cpaul@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Roman Pen [Tue, 26 Apr 2016 11:15:35 +0000 (13:15 +0200)]
workqueue: fix ghost PENDING flag while doing MQ IO
[ Upstream commit
346c09f80459a3ad97df1816d6d606169a51001a ]
The bug in a workqueue leads to a stalled IO request in MQ ctx->rq_list
with the following backtrace:
[ 601.347452] INFO: task kworker/u129:5:1636 blocked for more than 120 seconds.
[ 601.347574] Tainted: G O 4.4.5-1-storage+ #6
[ 601.347651] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 601.348142] kworker/u129:5 D
ffff880803077988 0 1636 2 0x00000000
[ 601.348519] Workqueue: ibnbd_server_fileio_wq ibnbd_dev_file_submit_io_worker [ibnbd_server]
[ 601.348999]
ffff880803077988 ffff88080466b900 ffff8808033f9c80 ffff880803078000
[ 601.349662]
ffff880807c95000 7fffffffffffffff ffffffff815b0920 ffff880803077ad0
[ 601.350333]
ffff8808030779a0 ffffffff815b01d5 0000000000000000 ffff880803077a38
[ 601.350965] Call Trace:
[ 601.351203] [<
ffffffff815b0920>] ? bit_wait+0x60/0x60
[ 601.351444] [<
ffffffff815b01d5>] schedule+0x35/0x80
[ 601.351709] [<
ffffffff815b2dd2>] schedule_timeout+0x192/0x230
[ 601.351958] [<
ffffffff812d43f7>] ? blk_flush_plug_list+0xc7/0x220
[ 601.352208] [<
ffffffff810bd737>] ? ktime_get+0x37/0xa0
[ 601.352446] [<
ffffffff815b0920>] ? bit_wait+0x60/0x60
[ 601.352688] [<
ffffffff815af784>] io_schedule_timeout+0xa4/0x110
[ 601.352951] [<
ffffffff815b3a4e>] ? _raw_spin_unlock_irqrestore+0xe/0x10
[ 601.353196] [<
ffffffff815b093b>] bit_wait_io+0x1b/0x70
[ 601.353440] [<
ffffffff815b056d>] __wait_on_bit+0x5d/0x90
[ 601.353689] [<
ffffffff81127bd0>] wait_on_page_bit+0xc0/0xd0
[ 601.353958] [<
ffffffff81096db0>] ? autoremove_wake_function+0x40/0x40
[ 601.354200] [<
ffffffff81127cc4>] __filemap_fdatawait_range+0xe4/0x140
[ 601.354441] [<
ffffffff81127d34>] filemap_fdatawait_range+0x14/0x30
[ 601.354688] [<
ffffffff81129a9f>] filemap_write_and_wait_range+0x3f/0x70
[ 601.354932] [<
ffffffff811ced3b>] blkdev_fsync+0x1b/0x50
[ 601.355193] [<
ffffffff811c82d9>] vfs_fsync_range+0x49/0xa0
[ 601.355432] [<
ffffffff811cf45a>] blkdev_write_iter+0xca/0x100
[ 601.355679] [<
ffffffff81197b1a>] __vfs_write+0xaa/0xe0
[ 601.355925] [<
ffffffff81198379>] vfs_write+0xa9/0x1a0
[ 601.356164] [<
ffffffff811c59d8>] kernel_write+0x38/0x50
The underlying device is a null_blk, with default parameters:
queue_mode = MQ
submit_queues = 1
Verification that nullb0 has something inflight:
root@pserver8:~# cat /sys/block/nullb0/inflight
0 1
root@pserver8:~# find /sys/block/nullb0/mq/0/cpu* -name rq_list -print -exec cat {} \;
...
/sys/block/nullb0/mq/0/cpu2/rq_list
CTX pending:
ffff8838038e2400
...
During debug it became clear that stalled request is always inserted in
the rq_list from the following path:
save_stack_trace_tsk + 34
blk_mq_insert_requests + 231
blk_mq_flush_plug_list + 281
blk_flush_plug_list + 199
wait_on_page_bit + 192
__filemap_fdatawait_range + 228
filemap_fdatawait_range + 20
filemap_write_and_wait_range + 63
blkdev_fsync + 27
vfs_fsync_range + 73
blkdev_write_iter + 202
__vfs_write + 170
vfs_write + 169
kernel_write + 56
So blk_flush_plug_list() was called with from_schedule == true.
If from_schedule is true, that means that finally blk_mq_insert_requests()
offloads execution of __blk_mq_run_hw_queue() and uses kblockd workqueue,
i.e. it calls kblockd_schedule_delayed_work_on().
That means, that we race with another CPU, which is about to execute
__blk_mq_run_hw_queue() work.
Further debugging shows the following traces from different CPUs:
CPU#0 CPU#1
---------------------------------- -------------------------------
reqeust A inserted
STORE hctx->ctx_map[0] bit marked
kblockd_schedule...() returns 1
<schedule to kblockd workqueue>
request B inserted
STORE hctx->ctx_map[1] bit marked
kblockd_schedule...() returns 0
*** WORK PENDING bit is cleared ***
flush_busy_ctxs() is executed, but
bit 1, set by CPU#1, is not observed
As a result request B pended forever.
This behaviour can be explained by speculative LOAD of hctx->ctx_map on
CPU#0, which is reordered with clear of PENDING bit and executed _before_
actual STORE of bit 1 on CPU#1.
The proper fix is an explicit full barrier <mfence>, which guarantees
that clear of PENDING bit is to be executed before all possible
speculative LOADS or STORES inside actual work function.
Signed-off-by: Roman Pen <roman.penyaev@profitbricks.com>
Cc: Gioh Kim <gi-oh.kim@profitbricks.com>
Cc: Michael Wang <yun.wang@profitbricks.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: linux-block@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: stable@vger.kernel.org
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Conrad Kostecki [Tue, 26 Apr 2016 08:08:10 +0000 (10:08 +0200)]
ALSA: hda - Add dock support for ThinkPad X260
[ Upstream commit
037e119738120c1cdc460c6ae33871c3000531f3 ]
Fixes audio output on a ThinkPad X260, when using Lenovo CES 2013
docking station series (basic, pro, ultra).
Signed-off-by: Conrad Kostecki <ck+linuxkernel@bl4ckb0x.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Shaohua Li [Mon, 25 Apr 2016 23:52:38 +0000 (16:52 -0700)]
MD: make bio mergeable
[ Upstream commit
9c573de3283af007ea11c17bde1e4568d9417328 ]
blk_queue_split marks bio unmergeable, which makes sense for normal bio.
But if dispatching the bio to underlayer disk, the blk_queue_split
checks are invalid, hence it's possible the bio becomes mergeable.
In the reported bug, this bug causes trim against raid0 performance slash
https://bugzilla.kernel.org/show_bug.cgi?id=117051
Reported-and-tested-by: Park Ju Hyung <qkrwngud825@gmail.com>
Fixes:
6ac45aeb6bca(block: avoid to merge splitted bio)
Cc: stable@vger.kernel.org (v4.3+)
Cc: Ming Lei <ming.lei@canonical.com>
Cc: Neil Brown <neilb@suse.de>
Reviewed-by: Jens Axboe <axboe@fb.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Hans Verkuil [Fri, 22 Apr 2016 07:00:50 +0000 (04:00 -0300)]
[media] v4l2-dv-timings.h: fix polarity for 4k formats
[ Upstream commit
3020ca711871fdaf0c15c8bab677a6bc302e28fe ]
The VSync polarity was negative instead of positive for the 4k CEA formats.
I probably copy-and-pasted these from the DMT 4k format, which does have a
negative VSync polarity.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reported-by: Martin Bugge <marbugge@cisco.com>
Cc: <stable@vger.kernel.org> # for v4.1 and up
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Jasem Mutlaq [Tue, 19 Apr 2016 07:38:27 +0000 (10:38 +0300)]
USB: serial: cp210x: add Straizona Focusers device ids
[ Upstream commit
613ac23a46e10d4d4339febdd534fafadd68e059 ]
Adding VID:PID for Straizona Focusers to cp210x driver.
Signed-off-by: Jasem Mutlaq <mutlaqja@ikarustech.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Mike Manning [Mon, 18 Apr 2016 12:13:23 +0000 (12:13 +0000)]
USB: serial: cp210x: add ID for Link ECU
[ Upstream commit
1d377f4d690637a0121eac8701f84a0aa1e69a69 ]
The Link ECU is an aftermarket ECU computer for vehicles that provides
full tuning abilities as well as datalogging and displaying capabilities
via the USB to Serial adapter built into the device.
Signed-off-by: Mike Manning <michael@bsch.com.au>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Laszlo Ersek [Thu, 21 Apr 2016 16:21:11 +0000 (18:21 +0200)]
efi: Fix out-of-bounds read in variable_matches()
[ Upstream commit
630ba0cc7a6dbafbdee43795617c872b35cde1b4 ]
The variable_matches() function can currently read "var_name[len]", for
example when:
- var_name[0] == 'a',
- len == 1
- match_name points to the NUL-terminated string "ab".
This function is supposed to accept "var_name" inputs that are not
NUL-terminated (hence the "len" parameter"). Document the function, and
access "var_name[*match]" only if "*match" is smaller than "len".
Reported-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Cc: Peter Jones <pjones@redhat.com>
Cc: Matthew Garrett <mjg59@coreos.com>
Cc: Jason Andryuk <jandryuk@gmail.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: <stable@vger.kernel.org> # v3.10+
Link: http://thread.gmane.org/gmane.comp.freedesktop.xorg.drivers.intel/86906
Signed-off-by: Matt Fleming <matt@codeblueprint.co.uk>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Krzysztof Kozlowski [Mon, 4 Apr 2016 05:54:59 +0000 (14:54 +0900)]
iio: ak8975: Fix NULL pointer exception on early interrupt
[ Upstream commit
07d2390e36ee5b3265e9cc8305f2a106c8721e16 ]
In certain probe conditions the interrupt came right after registering
the handler causing a NULL pointer exception because of uninitialized
waitqueue:
$ udevadm trigger
i2c-gpio i2c-gpio-1: using pins 143 (SDA) and 144 (SCL)
i2c-gpio i2c-gpio-3: using pins 53 (SDA) and 52 (SCL)
Unable to handle kernel NULL pointer dereference at virtual address
00000000
pgd =
e8b38000
[
00000000] *pgd=
00000000
Internal error: Oops: 5 [#1] SMP ARM
Modules linked in: snd_soc_i2s(+) i2c_gpio(+) snd_soc_idma snd_soc_s3c_dma snd_soc_core snd_pcm_dmaengine snd_pcm snd_timer snd soundcore ac97_bus spi_s3c64xx pwm_samsung dwc2 exynos_adc phy_exynos_usb2 exynosdrm exynos_rng rng_core rtc_s3c
CPU: 0 PID: 717 Comm: data-provider-m Not tainted 4.6.0-rc1-next-
20160401-00011-g1b8d87473b9e-dirty #101
Hardware name: SAMSUNG EXYNOS (Flattened Device Tree)
(...)
(__wake_up_common) from [<
c0379624>] (__wake_up+0x38/0x4c)
(__wake_up) from [<
c0a41d30>] (ak8975_irq_handler+0x28/0x30)
(ak8975_irq_handler) from [<
c0386720>] (handle_irq_event_percpu+0x88/0x140)
(handle_irq_event_percpu) from [<
c038681c>] (handle_irq_event+0x44/0x68)
(handle_irq_event) from [<
c0389c40>] (handle_edge_irq+0xf0/0x19c)
(handle_edge_irq) from [<
c0385e04>] (generic_handle_irq+0x24/0x34)
(generic_handle_irq) from [<
c05ee360>] (exynos_eint_gpio_irq+0x50/0x68)
(exynos_eint_gpio_irq) from [<
c0386720>] (handle_irq_event_percpu+0x88/0x140)
(handle_irq_event_percpu) from [<
c038681c>] (handle_irq_event+0x44/0x68)
(handle_irq_event) from [<
c0389a70>] (handle_fasteoi_irq+0xb4/0x194)
(handle_fasteoi_irq) from [<
c0385e04>] (generic_handle_irq+0x24/0x34)
(generic_handle_irq) from [<
c03860b4>] (__handle_domain_irq+0x5c/0xb4)
(__handle_domain_irq) from [<
c0301774>] (gic_handle_irq+0x54/0x94)
(gic_handle_irq) from [<
c030c910>] (__irq_usr+0x50/0x80)
The bug was reproduced on exynos4412-trats2 (with a max77693 device also
using i2c-gpio) after building max77693 as a module.
Cc: <stable@vger.kernel.org>
Fixes:
94a6d5cf7caa ("iio:ak8975 Implement data ready interrupt handling")
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Tested-by: Gregor Boirie <gregor.boirie@parrot.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Jack Pham [Fri, 15 Apr 2016 06:37:26 +0000 (23:37 -0700)]
regmap: spmi: Fix regmap_spmi_ext_read in multi-byte case
[ Upstream commit
dec8e8f6e6504aa3496c0f7cc10c756bb0e10f44 ]
Specifically for the case of reads that use the Extended Register
Read Long command, a multi-byte read operation is broken up into
8-byte chunks. However the call to spmi_ext_register_readl() is
incorrectly passing 'val_size', which if greater than 8 will
always fail. The argument should instead be 'len'.
Fixes:
c9afbb05a9ff ("regmap: spmi: support base and extended register spaces")
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Srinivas Kandagatla [Fri, 1 Apr 2016 07:52:57 +0000 (08:52 +0100)]
ata: ahci-platform: Add ports-implemented DT bindings.
[ Upstream commit
17dcc37e3e847bc0e67a5b1ec52471fcc6c18682 ]
On some SOCs PORTS_IMPL register value is never programmed by the
firmware and left at zero value. Which means that no sata ports are
available for software. AHCI driver used to cope up with this by
fabricating the port_map if the PORTS_IMPL register is read zero,
but recent patch broke this workaround as zero value was valid for
NVMe disks.
This patch adds ports-implemented DT bindings as workaround for this issue
in a way that DT can can override the PORTS_IMPL register in cases where
the firmware did not program it already.
Fixes:
566d1827df2e ("libata: disable forced PORTS_IMPL for >= AHCI 1.3")
Cc: stable@vger.kernel.org # v4.5+
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Tejun Heo <tj@kernel.org>
Reviewed-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Srinivas Kandagatla [Fri, 1 Apr 2016 07:52:56 +0000 (08:52 +0100)]
libahci: save port map for forced port map
[ Upstream commit
2fd0f46cb1b82587c7ae4a616d69057fb9bd0af7 ]
In usecases where force_port_map is used saved_port_map is never set,
resulting in not programming the PORTS_IMPL register as part of initial
config. This patch fixes this by setting it to port_map even in case
where force_port_map is used, making it more inline with other parts of
the code.
Fixes:
566d1827df2e ("libata: disable forced PORTS_IMPL for >= AHCI 1.3")
Cc: stable@vger.kernel.org # v4.5+
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Tejun Heo <tj@kernel.org>
Reviewed-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Krzysztof Kozlowski [Mon, 28 Mar 2016 04:09:56 +0000 (13:09 +0900)]
regulator: s2mps11: Fix invalid selector mask and voltages for buck9
[ Upstream commit
3b672623079bb3e5685b8549e514f2dfaa564406 ]
The buck9 regulator of S2MPS11 PMIC had incorrect vsel_mask (0xff
instead of 0x1f) thus reading entire register as buck9's voltage. This
effectively caused regulator core to interpret values as higher voltages
than they were and then to set real voltage much lower than intended.
The buck9 provides power to other regulators, including LDO13
and LDO19 which supply the MMC2 (SD card). On Odroid XU3/XU4 the lower
voltage caused SD card detection errors on Odroid XU3/XU4:
mmc1: card never left busy state
mmc1: error -110 whilst initialising SD card
During driver probe the regulator core was checking whether initial
voltage matches the constraints. With incorrect vsel_mask of 0xff and
default value of 0x50, the core interpreted this as 5 V which is outside
of constraints (3-3.775 V). Then the regulator core was adjusting the
voltage to match the constraints. With incorrect vsel_mask this new
voltage mapped to a vere low voltage in the driver.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Sugar Zhang [Fri, 18 Mar 2016 06:54:22 +0000 (14:54 +0800)]
ASoC: rt5640: Correct the digital interface data select
[ Upstream commit
653aa4645244042826f105aab1be3d01b3d493ca ]
this patch corrects the interface adc/dac control register definition
according to datasheet.
Signed-off-by: Sugar Zhang <sugar.zhang@rock-chips.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Sasha Levin [Fri, 13 May 2016 02:08:02 +0000 (22:08 -0400)]
iwlwifi: pcie: lower the debug level for RSA semaphore access
[ Upstream commit
9fc515bc9e735c10cd327f05c20f5ef69474188d ]
IWL_INFO is not an error but still printed by default.
"can't access the RSA semaphore it is write protected" seems
worrisome but it is not really a problem.
CC: <stable@vger.kernel.org> [4.1+]
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Sasha Levin [Fri, 13 May 2016 02:04:35 +0000 (22:04 -0400)]
stable: remove artifact created on backport
I have erroneously created a copy of said file when backporting
a commit back to the tree, and have ended up commiting it.
Remove it from the tree.
Reported-by: Jens Rottmann <Jens.Rottmann@adlinktech.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Greg Kroah-Hartman [Sat, 20 Feb 2016 22:19:34 +0000 (14:19 -0800)]
Revert "usb: hub: do not clear BOS field during reset device"
This reverts commit
522dc09ca0451d118795e8a05c7b3717f3d1ad8b..
Tony writes:
This upstream commit is causing an oops:
d8f00cd685f5 ("usb: hub: do not clear BOS field during reset device")
This patch has already been included in several -stable kernels. Here
are the affected kernels:
4.5.0-rc4 (current git)
4.4.2
4.3.6 (currently in review)
4.1.18
3.18.27
3.14.61
How to reproduce the problem:
Boot kernel with slub debugging enabled (otherwise memory corruption
will cause random oopses later instead of immediately)
Plug in USB 3.0 disk to xhci USB 3.0 port
dd if=/dev/sdc of=/dev/null bs=65536
(where /dev/sdc is the USB 3.0 disk)
Unplug USB cable while dd is still going
Oops is immediate:
Reported-by: Tony Battersby <tonyb@cybernetics.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Sasha Levin [Wed, 11 May 2016 04:10:35 +0000 (00:10 -0400)]
Linux 4.1.24
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Tony Luck [Thu, 14 Apr 2016 17:21:52 +0000 (10:21 -0700)]
x86 EDAC, sb_edac.c: Repair damage introduced when "fixing" channel address
[ Upstream commit
ff15e95c82768d589957dbb17d7eb7dba7904659 ]
In commit:
eb1af3b71f9d ("Fix computation of channel address")
I switched the "sck_way" variable from holding the log2 value read
from the h/w to instead be the actual number. Unfortunately it
is needed in log2 form when used to shift the address.
Tested-by: Patrick Geary <patrickg@supermicro.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Acked-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Cc: Aristeu Rozanski <arozansk@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-edac@vger.kernel.org
Cc: stable@vger.kernel.org
Fixes:
eb1af3b71f9d ("Fix computation of channel address")
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Jan Beulich [Thu, 21 Apr 2016 06:27:04 +0000 (00:27 -0600)]
x86/mm/xen: Suppress hugetlbfs in PV guests
[ Upstream commit
103f6112f253017d7062cd74d17f4a514ed4485c ]
Huge pages are not normally available to PV guests. Not suppressing
hugetlbfs use results in an endless loop of page faults when user mode
code tries to access a hugetlbfs mapped area (since the hypervisor
denies such PTEs to be created, but error indications can't be
propagated out of xen_set_pte_at(), just like for various of its
siblings), and - once killed in an oops like this:
kernel BUG at .../fs/hugetlbfs/inode.c:428!
invalid opcode: 0000 [#1] SMP
...
RIP: e030:[<
ffffffff811c333b>] [<
ffffffff811c333b>] remove_inode_hugepages+0x25b/0x320
...
Call Trace:
[<
ffffffff811c3415>] hugetlbfs_evict_inode+0x15/0x40
[<
ffffffff81167b3d>] evict+0xbd/0x1b0
[<
ffffffff8116514a>] __dentry_kill+0x19a/0x1f0
[<
ffffffff81165b0e>] dput+0x1fe/0x220
[<
ffffffff81150535>] __fput+0x155/0x200
[<
ffffffff81079fc0>] task_work_run+0x60/0xa0
[<
ffffffff81063510>] do_exit+0x160/0x400
[<
ffffffff810637eb>] do_group_exit+0x3b/0xa0
[<
ffffffff8106e8bd>] get_signal+0x1ed/0x470
[<
ffffffff8100f854>] do_signal+0x14/0x110
[<
ffffffff810030e9>] prepare_exit_to_usermode+0xe9/0xf0
[<
ffffffff814178a5>] retint_user+0x8/0x13
This is CVE-2016-3961 / XSA-174.
Reported-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: David Vrabel <david.vrabel@citrix.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Juergen Gross <JGross@suse.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Luis R. Rodriguez <mcgrof@suse.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Toshi Kani <toshi.kani@hp.com>
Cc: stable@vger.kernel.org
Cc: xen-devel <xen-devel@lists.xenproject.org>
Link: http://lkml.kernel.org/r/57188ED802000078000E431C@prv-mh.provo.novell.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Dominik Dingel [Fri, 17 Jul 2015 23:23:39 +0000 (16:23 -0700)]
s390/hugetlb: add hugepages_supported define
[ Upstream commit
7f9be77555bb2e52de84e9dddf7b4eb20cc6e171 ]
On s390 we only can enable hugepages if the underlying hardware/hypervisor
also does support this. Common code now would assume this to be
signaled by setting HPAGE_SHIFT to 0. But on s390, where we only
support one hugepage size, there is a link between HPAGE_SHIFT and
pageblock_order.
So instead of setting HPAGE_SHIFT to 0, we will implement the check for
the hardware capability.
Signed-off-by: Dominik Dingel <dingel@linux.vnet.ibm.com>
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Cc: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Dominik Dingel [Fri, 17 Jul 2015 23:23:37 +0000 (16:23 -0700)]
mm: hugetlb: allow hugepages_supported to be architecture specific
[ Upstream commit
2531c8cf56a640cd7d17057df8484e570716a450 ]
s390 has a constant hugepage size, by setting HPAGE_SHIFT we also change
e.g. the pageblock_order, which should be independent in respect to
hugepage support.
With this patch every architecture is free to define how to check
for hugepage support.
Signed-off-by: Dominik Dingel <dingel@linux.vnet.ibm.com>
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Cc: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Huacai Chen [Tue, 19 Apr 2016 11:19:11 +0000 (19:19 +0800)]
drm: Loongson-3 doesn't fully support wc memory
[ Upstream commit
221004c66a58949a0f25c937a6789c0839feb530 ]
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Cc: stable@vger.kernel.org
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Jérôme Glisse [Tue, 19 Apr 2016 13:07:50 +0000 (09:07 -0400)]
drm/radeon: forbid mapping of userptr bo through radeon device file
[ Upstream commit
b5dcec693f87cb8475f2291c0075b2422addd3d6 ]
Allowing userptr bo which are basicly a list of page from some vma
(so either anonymous page or file backed page) would lead to serious
corruption of kernel structures and counters (because we overwrite
the page->mapping field when mapping buffer).
This will already block if the buffer was populated before anyone does
try to mmap it because then TTM_PAGE_FLAG_SG would be set in in the
ttm_tt flags. But that flag is check before ttm_tt_populate in the ttm
vm fault handler.
So to be safe just add a check to verify_access() callback.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Jérôme Glisse <jglisse@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
cpaul@redhat.com [Mon, 4 Apr 2016 23:58:47 +0000 (19:58 -0400)]
drm/dp/mst: Validate port in drm_dp_payload_send_msg()
[ Upstream commit
deba0a2af9592b2022a0bce7b085a318b53ce1db ]
With the joys of things running concurrently, there's always a chance
that the port we get passed in drm_dp_payload_send_msg() isn't actually
valid anymore. Because of this, we need to make sure we validate the
reference to the port before we use it otherwise we risk running into
various race conditions. For instance, on the Dell MST monitor I have
here for testing, hotplugging it enough times causes us to kernel panic:
[drm:intel_mst_enable_dp] 1
[drm:drm_dp_update_payload_part2] payload 0 1
[drm:intel_get_hpd_pins] hotplug event received, stat 0x00200000, dig 0x10101011, pins 0x00000020
[drm:intel_hpd_irq_handler] digital hpd port B - short
[drm:intel_dp_hpd_pulse] got hpd irq on port B - short
[drm:intel_dp_check_mst_status] got esi 00 10 00
[drm:drm_dp_update_payload_part2] payload 1 1
general protection fault: 0000 [#1] SMP
…
Call Trace:
[<
ffffffffa012b632>] drm_dp_update_payload_part2+0xc2/0x130 [drm_kms_helper]
[<
ffffffffa032ef08>] intel_mst_enable_dp+0xf8/0x180 [i915]
[<
ffffffffa0310dbd>] haswell_crtc_enable+0x3ed/0x8c0 [i915]
[<
ffffffffa030c84d>] intel_atomic_commit+0x5ad/0x1590 [i915]
[<
ffffffffa01db877>] ? drm_atomic_set_crtc_for_connector+0x57/0xe0 [drm]
[<
ffffffffa01dc4e7>] drm_atomic_commit+0x37/0x60 [drm]
[<
ffffffffa0130a3a>] drm_atomic_helper_set_config+0x7a/0xb0 [drm_kms_helper]
[<
ffffffffa01cc482>] drm_mode_set_config_internal+0x62/0x100 [drm]
[<
ffffffffa01d02ad>] drm_mode_setcrtc+0x3cd/0x4e0 [drm]
[<
ffffffffa01c18e3>] drm_ioctl+0x143/0x510 [drm]
[<
ffffffffa01cfee0>] ? drm_mode_setplane+0x1b0/0x1b0 [drm]
[<
ffffffff810f79a7>] ? hrtimer_start_range_ns+0x1b7/0x3a0
[<
ffffffff81212962>] do_vfs_ioctl+0x92/0x570
[<
ffffffff81590852>] ? __sys_recvmsg+0x42/0x80
[<
ffffffff81212eb9>] SyS_ioctl+0x79/0x90
[<
ffffffff816b4e32>] entry_SYSCALL_64_fastpath+0x1a/0xa4
RIP [<
ffffffffa012b026>] drm_dp_payload_send_msg+0x146/0x1f0 [drm_kms_helper]
Which occurs because of the hotplug event shown in the log, which ends
up causing DRM's dp helpers to drop the port we're updating the payload
on and panic.
CC: stable@vger.kernel.org
Signed-off-by: Lyude <cpaul@redhat.com>
Reviewed-by: David Airlie <airlied@linux.ie>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Takashi Iwai [Thu, 21 Apr 2016 15:37:54 +0000 (17:37 +0200)]
ALSA: pcxhr: Fix missing mutex unlock
[ Upstream commit
67f3754b51f22b18c4820fb84062f658c30e8644 ]
The commit [
9bef72bdb26e: ALSA: pcxhr: Use nonatomic PCM ops]
converted to non-atomic PCM ops, but shamelessly with an unbalanced
mutex locking, which leads to the hangup easily. Fix it.
Fixes:
9bef72bdb26e ('ALSA: pcxhr: Use nonatomic PCM ops')
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=116441
Cc: <stable@vger.kernel.org> # 3.18+
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Sebastian Andrzej Siewior [Fri, 15 Apr 2016 12:35:39 +0000 (14:35 +0200)]
futex: Handle unlock_pi race gracefully
[ Upstream commit
89e9e66ba1b3bde9d8ea90566c2aee20697ad681 ]
If userspace calls UNLOCK_PI unconditionally without trying the TID -> 0
transition in user space first then the user space value might not have the
waiters bit set. This opens the following race:
CPU0 CPU1
uval = get_user(futex)
lock(hb)
lock(hb)
futex |= FUTEX_WAITERS
....
unlock(hb)
cmpxchg(futex, uval, newval)
So the cmpxchg fails and returns -EINVAL to user space, which is wrong because
the futex value is valid.
To handle this (yes, yet another) corner case gracefully, check for a flag
change and retry.
[ tglx: Massaged changelog and slightly reworked implementation ]
Fixes:
ccf9e6a80d9e ("futex: Make unlock_pi more robust")
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: stable@vger.kernel.org
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: Darren Hart <dvhart@linux.intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1460723739-5195-1-git-send-email-bigeasy@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Lu, Han [Wed, 20 Apr 2016 02:08:43 +0000 (10:08 +0800)]
ALSA: hda - add PCI ID for Intel Broxton-T
[ Upstream commit
9859a971ca228725425238756ee89c6133306ec8 ]
Add HD Audio Device PCI ID for the Intel Broxton-T platform.
It is an HDA Intel PCH controller.
Signed-off-by: Lu, Han <han.lu@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Lu, Han [Thu, 19 Nov 2015 15:25:12 +0000 (23:25 +0800)]
ALSA: hda - add PCI IDs for Intel Broxton
[ Upstream commit
c87693da69f979f8a4370e7bc6115dd0898d8501 ]
Add HD Audio Device PCI ID for the Intel Broxton platform.
It is an HDA Intel PCH controller.
Signed-off-by: Lu, Han <han.lu@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Lars-Peter Clausen [Thu, 14 Apr 2016 15:01:17 +0000 (17:01 +0200)]
usb: gadget: f_fs: Fix use-after-free
[ Upstream commit
38740a5b87d53ceb89eb2c970150f6e94e00373a ]
When using asynchronous read or write operations on the USB endpoints the
issuer of the IO request is notified by calling the ki_complete() callback
of the submitted kiocb when the URB has been completed.
Calling this ki_complete() callback will free kiocb. Make sure that the
structure is no longer accessed beyond that point, otherwise undefined
behaviour might occur.
Fixes:
2e4c7553cd6f ("usb: gadget: f_fs: add aio support")
Cc: <stable@vger.kernel.org> # v3.15+
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Alex Deucher [Mon, 18 Apr 2016 15:19:19 +0000 (11:19 -0400)]
Revert "drm/radeon: disable runtime pm on PX laptops without dGPU power control"
[ Upstream commit
bfaddd9fc8ac048b99475f000dbef6f08297417f ]
This reverts commit
e64c952efb8e0c15ae82cec8e455ab4910690ef1.
ATPX is the ACPI method for controlling AMD PowerXpress laptops.
There are flags to indicate which methods are supported. If
the dGPU power down flag is not supported, the driver needs to
implement the dGPU power down manually. We had previously
always forced the driver to assume the ATPX dGPU power down
was present, but this causes problems on boards where it is
not, leading to GPU hangs when attempting to power down the
dGPU. Manual dGPU power down is not currently supported in
the Linux driver. Some laptops indicate that the ATPX
dGPU power down method is not present, but it actually
apparently is. I'm not sure if this is a bios bug and it should
be set or if there is a reason it was unset and the method should
not be used. This is not an issue on other OSes since both the
ATPX and the manual driver power down methods are supported.
This is apparently fairly widespread, so just revert for now.
bugs:
https://bugzilla.kernel.org/show_bug.cgi?id=115321
https://bugzilla.kernel.org/show_bug.cgi?id=116581
https://bugzilla.kernel.org/show_bug.cgi?id=116251
Cc: stable@vger.kernel.org
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Alex Deucher [Thu, 14 Apr 2016 18:15:16 +0000 (14:15 -0400)]
drm/radeon: add a quirk for a XFX R9 270X
[ Upstream commit
bcb31eba4a4ea356fd61cbd5dec5511c3883f57e ]
bug:
https://bugs.freedesktop.org/show_bug.cgi?id=76490
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Alex Deucher [Mon, 28 Mar 2016 14:16:40 +0000 (10:16 -0400)]
drm/radeon: add another R7 370 quirk
[ Upstream commit
a64663d9870364bd2a2df62bf0d3a9fbe5ea62a8 ]
bug:
https://bugzilla.kernel.org/show_bug.cgi?id=115291
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Alex Deucher [Fri, 2 Oct 2015 20:12:07 +0000 (16:12 -0400)]
drm/radeon: add quirk for ASUS R7 370
[ Upstream commit
2b02ec79004388a8c65e227bc289ed891b5ac8c6 ]
Bug:
https://bugs.freedesktop.org/show_bug.cgi?id=92260
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Maxim Sheviakov [Wed, 23 Sep 2015 21:10:51 +0000 (17:10 -0400)]
drm/radeon: add quirk for MSI R7 370
[ Upstream commit
e78654799135a788a941bacad3452fbd7083e518 ]
Just adds the quirk for MSI R7 370 Armor 2X
Bug:
https://bugs.freedesktop.org/show_bug.cgi?id=91294
Signed-off-by: Maxim Sheviakov <mrader3940@yandex.ru>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Anton Blanchard [Fri, 15 Apr 2016 02:07:24 +0000 (12:07 +1000)]
powerpc: Update cpu_user_features2 in scan_features()
[ Upstream commit
beff82374b259d726e2625ec6c518a5f2613f0ae ]
scan_features() updates cpu_user_features but not cpu_user_features2.
Amongst other things, cpu_user_features2 contains the user TM feature
bits which we must keep in sync with the kernel TM feature bit.
Signed-off-by: Anton Blanchard <anton@samba.org>
Cc: stable@vger.kernel.org
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Anton Blanchard [Fri, 15 Apr 2016 02:06:13 +0000 (12:06 +1000)]
powerpc: scan_features() updates incorrect bits for REAL_LE
[ Upstream commit
6997e57d693b07289694239e52a10d2f02c3a46f ]
The REAL_LE feature entry in the ibm_pa_feature struct is missing an MMU
feature value, meaning all the remaining elements initialise the wrong
values.
This means instead of checking for byte 5, bit 0, we check for byte 0,
bit 0, and then we incorrectly set the CPU feature bit as well as MMU
feature bit 1 and CPU user feature bits 0 and 2 (5).
Checking byte 0 bit 0 (IBM numbering), means we're looking at the
"Memory Management Unit (MMU)" feature - ie. does the CPU have an MMU.
In practice that bit is set on all platforms which have the property.
This means we set CPU_FTR_REAL_LE always. In practice that seems not to
matter because all the modern cpus which have this property also
implement REAL_LE, and we've never needed to disable it.
We're also incorrectly setting MMU feature bit 1, which is:
#define MMU_FTR_TYPE_8xx 0x00000002
Luckily the only place that looks for MMU_FTR_TYPE_8xx is in Book3E
code, which can't run on the same cpus as scan_features(). So this also
doesn't matter in practice.
Finally in the CPU user feature mask, we're setting bits 0 and 2. Bit 2
is not currently used, and bit 0 is:
#define PPC_FEATURE_PPC_LE 0x00000001
Which says the CPU supports the old style "PPC Little Endian" mode.
Again this should be harmless in practice as no 64-bit CPUs implement
that mode.
Fix the code by adding the missing initialisation of the MMU feature.
Also add a comment marking CPU user feature bit 2 (0x4) as reserved. It
would be unsafe to start using it as old kernels incorrectly set it.
Fixes:
44ae3ab3358e ("powerpc: Free up some CPU feature bits by moving out MMU-related features")
Signed-off-by: Anton Blanchard <anton@samba.org>
Cc: stable@vger.kernel.org
[mpe: Flesh out changelog, add comment reserving 0x4]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Bastien Nocera [Mon, 18 Apr 2016 09:10:42 +0000 (11:10 +0200)]
ALSA: hda/realtek - Add ALC3234 headset mode for Optiplex 9020m
[ Upstream commit
afecb146d8d8a60a1dde9cdf570c278649617fde ]
The Optiplex 9020m with Haswell-DT processor needs a quirk for the
headset jack at the front of the machine to be able to use microphones.
A quirk for this model was originally added in 3127899, but c77900e
removed it in favour of a more generic version.
Unfortunately, pin configurations can changed based on firmware/BIOS
versions, and the generic version doesn't have any effect on newer
versions of the machine/firmware anymore.
With help from David Henningsson <diwic@ubuntu.com>
Signed-off-by: Bastien Nocera <hadess@hadess.net>
Tested-by: Bastien Nocera <hadess@hadess.net>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Ville Syrjälä [Thu, 14 Apr 2016 11:39:02 +0000 (14:39 +0300)]
drm/i915: Use fw_domains_put_with_fifo() on HSW
[ Upstream commit
31318a922395ec9e78d6e2ddf70779355afc7594 ]
HSW still has the wake FIFO, so let's check it.
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Deepak S <deepak.s@linux.intel.com>
Fixes:
05a2fb157e44 ("drm/i915: Consolidate forcewake code")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460633942-24013-1-git-send-email-ville.syrjala@linux.intel.com
Cc: stable@vger.kernel.org
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
(cherry picked from commit
3d7d0c85e41afb5a05e98b3a8a72c38357f02594)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Tom Lendacky [Wed, 13 Apr 2016 15:52:25 +0000 (10:52 -0500)]
crypto: ccp - Prevent information leakage on export
[ Upstream commit
f709b45ec461b548c41a00044dba1f1b572783bf ]
Prevent information from leaking to userspace by doing a memset to 0 of
the export state structure before setting the structure values and copying
it. This prevents un-initialized padding areas from being copied into the
export area.
Cc: <stable@vger.kernel.org> # 3.14.x-
Reported-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Xiaodong Liu [Tue, 12 Apr 2016 09:45:51 +0000 (09:45 +0000)]
crypto: sha1-mb - use corrcet pointer while completing jobs
[ Upstream commit
0851561d9c965df086ef8a53f981f5f95a57c2c8 ]
In sha_complete_job, incorrect mcryptd_hash_request_ctx pointer is used
when check and complete other jobs. If the memory of first completed req
is freed, while still completing other jobs in the func, kernel will
crash since NULL pointer is assigned to RIP.
Cc: <stable@vger.kernel.org>
Signed-off-by: Xiaodong Liu <xiaodong.liu@intel.com>
Acked-by: Tim Chen <tim.c.chen@linux.intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Yingjoe Chen [Sat, 2 Apr 2016 06:57:49 +0000 (14:57 +0800)]
pinctrl: mediatek: correct debounce time unit in mtk_gpio_set_debounce
[ Upstream commit
5fedbb923936174ab4d1d5cc92bca1cf6b2e0ca2 ]
The debounce time unit for gpio_chip.set_debounce is us but
mtk_gpio_set_debounce regard it as ms.
Fix this by correct debounce time array dbnc_arr so it can find correct
debounce setting. Debounce time for first debounce setting is 500us,
correct this as well.
While I'm at it, also change the debounce time array name to
"debounce_time" for readability.
Cc: stable@vger.kernel.org
Signed-off-by: Yingjoe Chen <yingjoe.chen@mediatek.com>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Acked-by: Hongzhou Yang <hongzhou.yang@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Alex Deucher [Wed, 13 Apr 2016 16:08:27 +0000 (12:08 -0400)]
drm/radeon: fix initial connector audio value
[ Upstream commit
7403c515c49c033fec33df0814fffdc977e6acdc ]
This got lost somewhere along the way. This fixes
audio not working until set_property was called.
Noticed-by: Hyungwon Hwang <hyungwon.hwang7@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Dmitry Ivanov [Wed, 6 Apr 2016 14:23:18 +0000 (17:23 +0300)]
nl80211: check netlink protocol in socket release notification
[ Upstream commit
8f815cdde3e550e10c2736990d791f60c2ce43eb ]
A non-privileged user can create a netlink socket with the same port_id as
used by an existing open nl80211 netlink socket (e.g. as used by a hostapd
process) with a different protocol number.
Closing this socket will then lead to the notification going to nl80211's
socket release notification handler, and possibly cause an action such as
removing a virtual interface.
Fix this issue by checking that the netlink protocol is NETLINK_GENERIC.
Since generic netlink has no notifier chain of its own, we can't fix the
problem more generically.
Fixes:
026331c4d9b5 ("cfg80211/mac80211: allow registering for and sending action frames")
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Ivanov <dima@ubnt.com>
[rewrite commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Dmitry Ivanov [Thu, 7 Apr 2016 07:31:38 +0000 (09:31 +0200)]
netlink: don't send NETLINK_URELEASE for unbound sockets
[ Upstream commit
e27260203912b40751fa353d009eaa5a642c739f ]
All existing users of NETLINK_URELEASE use it to clean up resources that
were previously allocated to a socket via some command. As a result, no
users require getting this notification for unbound sockets.
Sending it for unbound sockets, however, is a problem because any user
(including unprivileged users) can create a socket that uses the same ID
as an existing socket. Binding this new socket will fail, but if the
NETLINK_URELEASE notification is generated for such sockets, the users
thereof will be tricked into thinking the socket that they allocated the
resources for is closed.
In the nl80211 case, this will cause destruction of virtual interfaces
that still belong to an existing hostapd process; this is the case that
Dmitry noticed. In the NFC case, it will cause a poll abort. In the case
of netlink log/queue it will cause them to stop reporting events, as if
NFULNL_CFG_CMD_UNBIND/NFQNL_CFG_CMD_UNBIND had been called.
Fix this problem by checking that the socket is bound before generating
the NETLINK_URELEASE notification.
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Ivanov <dima@ubnt.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
projects / platform / kernel / linux-exynos.git / log