firewire: core: extend card->lock in fw_core_handle_bus_reset

commit a7ecbe92b9243edbe94772f6f2c854e4142a3345 upstream.

card->local_node and card->bm_retries are both always accessed under
card->lock.
fw_core_handle_bus_reset has a check whose condition depends on
card->local_node and whose body writes to card->bm_retries.
Both of these accesses are not under card->lock. Move the lock acquiring
of card->lock to before this check such that these accesses do happen
when card->lock is held.
fw_destroy_nodes is called inside the check.
Since fw_destroy_nodes already acquires card->lock inside its function
body, move this out to the callsites of fw_destroy_nodes.
Also add a comment to indicate which locking is necessary when calling
fw_destroy_nodes.

Cc: <stable@vger.kernel.org>
Signed-off-by: Niels Dossche <dossche.niels@gmail.com>
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20220409041243.603210-4-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

firewire: remove check of list iterator against head past the loop body

commit 9423973869bd4632ffe669f950510c49296656e0 upstream.

When list_for_each_entry() completes the iteration over the whole list
without breaking the loop, the iterator value will be a bogus pointer
computed based on the head element.

While it is safe to use the pointer to determine if it was computed
based on the head element, either with list_entry_is_head() or
&pos->member == head, using the iterator variable after the loop should
be avoided.

In preparation to limit the scope of a list iterator to the list
traversal loop, use a dedicated pointer to point to the found element [1].

Link: https://lore.kernel.org/all/CAHk-=wgRr_D8CB-D9Kg-c=EHreAsk5SqXPwr9Y7k9sA6cWXJ6w@mail.gmail.com/
Cc: <stable@vger.kernel.org>
Signed-off-by: Jakob Koschel <jakobkoschel@gmail.com>
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20220409041243.603210-3-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

firewire: fix potential uaf in outbound_phy_packet_callback()

commit b7c81f80246fac44077166f3e07103affe6db8ff upstream.

&e->event and e point to the same address, and &e->event could
be freed in queue_event. So there is a potential uaf issue if
we dereference e after calling queue_event(). Fix this by adding
a temporary variable to maintain e->client in advance, this can
avoid the potential uaf issue.

Cc: <stable@vger.kernel.org>
Signed-off-by: Chengfeng Ye <cyeaa@connect.ust.hk>
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20220409041243.603210-2-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

timekeeping: Mark NMI safe time accessors as notrace

commit 2c33d775ef4c25c0e1e1cc0fd5496d02f76bfa20 upstream.

Mark the CLOCK_MONOTONIC fast time accessors as notrace. These functions are
used in tracing to retrieve timestamps, so they should not recurse.

Fixes: 4498e7467e9e ("time: Parametrize all tk_fast_mono users")
Fixes: f09cb9a1808e ("time: Introduce tk_fast_raw")
Reported-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20220426175338.3807ca4f@gandalf.local.home/
Link: https://lore.kernel.org/r/20220428062432.61063-1-kurt@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Revert "SUNRPC: attempt AF_LOCAL connect on setup"

commit a3d0562d4dc039bca39445e1cddde7951662e17d upstream.

This reverts commit 7073ea8799a8cf73db60270986f14e4aae20fa80.

We must not try to connect the socket while the transport is under
construction, because the mechanisms to safely tear it down are not in
place. As the code stands, we end up leaking the sockets on a connection
error.

Reported-by: wanghai (M) <wanghai38@huawei.com>
Cc: stable@vger.kernel.org
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

RISC-V: relocate DTB if it's outside memory region

commit c6fe81191bd74f7e6ae9ce96a4837df9485f3ab8 upstream.

In case the DTB provided by the bootloader/BootROM is before the kernel
image or outside /memory, we won't be able to access it through the
linear mapping, and get a segfault on setup_arch(). Currently OpenSBI
relocates DTB but that's not always the case (e.g. if FW_JUMP_FDT_ADDR
is not specified), and it's also not the most portable approach since
the default FW_JUMP_FDT_ADDR of the generic platform relocates the DTB
at a specific offset that may not be available. To avoid this situation
copy DTB so that it's visible through the linear mapping.

Signed-off-by: Nick Kossifidis <mick@ics.forth.gr>
Link: https://lore.kernel.org/r/20220322132839.3653682-1-mick@ics.forth.gr
Tested-by: Conor Dooley <conor.dooley@microchip.com>
Fixes: f105aa940e78 ("riscv: add BUILTIN_DTB support for MMU-enabled targets")
Cc: stable@vger.kernel.org
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/amdgpu: do not use passthrough mode in Xen dom0

commit 19965d8259fdabc6806da92adda49684f5bcbec5 upstream.

While technically Xen dom0 is a virtual machine too, it does have
access to most of the hardware so it doesn't need to be considered a
"passthrough". Commit b818a5d37454 ("drm/amdgpu/gmc: use PCI BARs for
APUs in passthrough") changed how FB is accessed based on passthrough
mode. This breaks amdgpu in Xen dom0 with message like this:

    [drm:dc_dmub_srv_wait_idle [amdgpu]] *ERROR* Error waiting for DMUB idle: status=3

While the reason for this failure is unclear, the passthrough mode is
not really necessary in Xen dom0 anyway. So, to unbreak booting affected
kernels, disable passthrough mode in this case.

Link: https://gitlab.freedesktop.org/drm/amd/-/issues/1985
Fixes: b818a5d37454 ("drm/amdgpu/gmc: use PCI BARs for APUs in passthrough")
Signed-off-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/amd/display: Avoid reading audio pattern past AUDIO_CHANNELS_COUNT

commit 3dfe85fa87b2a26bdbd292b66653bba065cf9941 upstream.

A faulty receiver might report an erroneous channel count. We
should guard against reading beyond AUDIO_CHANNELS_COUNT as
that would overflow the dpcd_pattern_period array.

Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iommu/arm-smmu-v3: Fix size calculation in arm_smmu_mm_invalidate_range()

commit 95d4782c34a60800ccf91d9f0703137d4367a2fc upstream.

The arm_smmu_mm_invalidate_range function is designed to be called
by mm core for Shared Virtual Addressing purpose between IOMMU and
CPU MMU. However, the ways of two subsystems defining their "end"
addresses are slightly different. IOMMU defines its "end" address
using the last address of an address range, while mm core defines
that using the following address of an address range:

include/linux/mm_types.h:
unsigned long vm_end;
/* The first byte after our end address ...

This mismatch resulted in an incorrect calculation for size so it
failed to be page-size aligned. Further, it caused a dead loop at
"while (iova < end)" check in __arm_smmu_tlb_inv_range function.

This patch fixes the issue by doing the calculation correctly.

Fixes: 2f7e8c553e98 ("iommu/arm-smmu-v3: Hook up ATC invalidation to mm ops")
Cc: stable@vger.kernel.org
Signed-off-by: Nicolin Chen <nicolinc@nvidia.com>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Reviewed-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Link: https://lore.kernel.org/r/20220419210158.21320-1-nicolinc@nvidia.com
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iommu/vt-d: Calculate mask for non-aligned flushes

commit 59bf3557cf2f8a469a554aea1e3d2c8e72a579f7 upstream.

Calculate the appropriate mask for non-size-aligned page selective
invalidation. Since psi uses the mask value to mask out the lower order
bits of the target address, properly flushing the iotlb requires using a
mask value such that [pfn, pfn+pages) all lie within the flushed
size-aligned region.  This is not normally an issue because iova.c
always allocates iovas that are aligned to their size. However, iovas
which come from other sources (e.g. userspace via VFIO) may not be
aligned.

To properly flush the IOTLB, both the start and end pfns need to be
equal after applying the mask. That means that the most efficient mask
to use is the index of the lowest bit that is equal where all higher
bits are also equal. For example, if pfn=0x17f and pages=3, then
end_pfn=0x181, so the smallest mask we can use is 8. Any differences
above the highest bit of pages are due to carrying, so by xnor'ing pfn
and end_pfn and then masking out the lower order bits based on pages, we
get 0xffffff00, where the first set bit is the mask we want to use.

Fixes: 6fe1010d6d9c ("vfio/type1: DMA unmap chunking")
Cc: stable@vger.kernel.org
Signed-off-by: David Stevens <stevensd@chromium.org>
Reviewed-by: Kevin Tian <kevin.tian@intel.com>
Link: https://lore.kernel.org/r/20220401022430.1262215-1-stevensd@google.com
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/20220410013533.3959168-2-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

KVM: x86/svm: Account for family 17h event renumberings in amd_pmc_perf_hw_id

commit 5eb849322d7f7ae9d5c587c7bc3b4f7c6872cd2f upstream.

Zen renumbered some of the performance counters that correspond to the
well known events in perf_hw_id. This code in KVM was never updated for
that, so guest that attempt to use counters on Zen that correspond to the
pre-Zen perf_hw_id values will silently receive the wrong values.

This has been observed in the wild with rr[0] when running in Zen 3
guests. rr uses the retired conditional branch counter 00d1 which is
incorrectly recognized by KVM as PERF_COUNT_HW_STALLED_CYCLES_BACKEND.

[0] https://rr-project.org/

Signed-off-by: Kyle Huey <me@kylehuey.com>
Message-Id: <20220503050136.86298-1-khuey@kylehuey.com>
Cc: stable@vger.kernel.org
[Check guest family, not host. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

x86/fpu: Prevent FPU state corruption

commit 59f5ede3bc0f00eb856425f636dab0c10feb06d8 upstream.

The FPU usage related to task FPU management is either protected by
disabling interrupts (switch_to, return to user) or via fpregs_lock() which
is a wrapper around local_bh_disable(). When kernel code wants to use the
FPU then it has to check whether it is possible by calling irq_fpu_usable().

But the condition in irq_fpu_usable() is wrong. It allows FPU to be used
when:

   !in_interrupt() || interrupted_user_mode() || interrupted_kernel_fpu_idle()

The latter is checking whether some other context already uses FPU in the
kernel, but if that's not the case then it allows FPU to be used
unconditionally even if the calling context interrupted a fpregs_lock()
critical region. If that happens then the FPU state of the interrupted
context becomes corrupted.

Allow in kernel FPU usage only when no other context has in kernel FPU
usage and either the calling context is not hard interrupt context or the
hard interrupt did not interrupt a local bottomhalf disabled region.

It's hard to find a proper Fixes tag as the condition was broken in one way
or the other for a very long time and the eager/lazy FPU changes caused a
lot of churn. Picked something remotely connected from the history.

This survived undetected for quite some time as FPU usage in interrupt
context is rare, but the recent changes to the random code unearthed it at
least on a kernel which had FPU debugging enabled. There is probably a
higher rate of silent corruption as not all issues can be detected by the
FPU debugging code. This will be addressed in a subsequent change.

Fixes: 5d2bd7009f30 ("x86, fpu: decouple non-lazy/eager fpu restore from xsave")
Reported-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: Borislav Petkov <bp@suse.de>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20220501193102.588689270@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

gpiolib: of: fix bounds check for 'gpio-reserved-ranges'

commit e75f88efac05bf4e107e4171d8db6d8c3937252d upstream.

Gpiolib interprets the elements of "gpio-reserved-ranges" as "start,size"
because it clears "size" bits starting from the "start" bit in the according
bitmap. So it has to use "greater" instead of "greater or equal" when performs
bounds check to make sure that GPIOs are in the available range.
Previous implementation skipped ranges that include the last GPIO in
the range.

I wrote the mail to the maintainers
(https://lore.kernel.org/linux-gpio/20220412115554.159435-1-andrei.lalaev@emlid.com/T/#u)
of the questioned DTSes (because I couldn't understand how the maintainers
interpreted this property), but I haven't received a response.
Since the questioned DTSes use "gpio-reserved-ranges = <0 4>"
(i.e., the beginning of the range), this patch doesn't affect these DTSes at all.
TBH this patch doesn't break any existing DTSes because none of them
reserve gpios at the end of range.

Fixes: 726cb3ba4969 ("gpiolib: Support 'gpio-reserved-ranges' property")
Signed-off-by: Andrei Lalaev <andrei.lalaev@emlid.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Cc: stable@vger.kernel.org
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mmc: core: Set HS clock speed before sending HS CMD13

commit 4bc31edebde51fcf8ad0794763b8679a7ecb5ec0 upstream.

Way back in commit 4f25580fb84d ("mmc: core: changes frequency to
hs_max_dtr when selecting hs400es"), Rockchip engineers noticed that
some eMMC don't respond to SEND_STATUS commands very reliably if they're
still running at a low initial frequency. As mentioned in that commit,
JESD84-B51 P49 suggests a sequence in which the host:
1. sets HS_TIMING
2. bumps the clock ("<= 52 MHz")
3. sends further commands

It doesn't exactly require that we don't use a lower-than-52MHz
frequency, but in practice, these eMMC don't like it.

The aforementioned commit tried to get that right for HS400ES, although
it's unclear whether this ever truly worked as committed into mainline,
as other changes/refactoring adjusted the sequence in conflicting ways:

08573eaf1a70 ("mmc: mmc: do not use CMD13 to get status after speed mode
switch")

53e60650f74e ("mmc: core: Allow CMD13 polling when switching to HS mode
for mmc")

In any case, today we do step 3 before step 2. Let's fix that, and also
apply the same logic to HS200/400, where this eMMC has problems too.

Resolves errors like this seen when booting some RK3399 Gru/Scarlet
systems:

[    2.058881] mmc1: CQHCI version 5.10
[    2.097545] mmc1: SDHCI controller on fe330000.mmc [fe330000.mmc] using ADMA
[    2.209804] mmc1: mmc_select_hs400es failed, error -84
[    2.215597] mmc1: error -84 whilst initialising MMC card
[    2.417514] mmc1: mmc_select_hs400es failed, error -110
[    2.423373] mmc1: error -110 whilst initialising MMC card
[    2.605052] mmc1: mmc_select_hs400es failed, error -110
[    2.617944] mmc1: error -110 whilst initialising MMC card
[    2.835884] mmc1: mmc_select_hs400es failed, error -110
[    2.841751] mmc1: error -110 whilst initialising MMC card

Ealier versions of this patch bumped to 200MHz/HS200 speeds too early,
which caused issues on, e.g., qcom-msm8974-fairphone-fp2. (Thanks for
the report Luca!) After a second look, it appears that aligns with
JESD84 / page 45 / table 28, so we need to keep to lower (HS / 52 MHz)
rates first.

Fixes: 08573eaf1a70 ("mmc: mmc: do not use CMD13 to get status after speed mode switch")
Fixes: 53e60650f74e ("mmc: core: Allow CMD13 polling when switching to HS mode for mmc")
Fixes: 4f25580fb84d ("mmc: core: changes frequency to hs_max_dtr when selecting hs400es")
Cc: Shawn Lin <shawn.lin@rock-chips.com>
Link: https://lore.kernel.org/linux-mmc/11962455.O9o76ZdvQC@g550jk/
Reported-by: Luca Weiss <luca@z3ntu.xyz>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Tested-by: Luca Weiss <luca@z3ntu.xyz>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20220422100824.v4.1.I484f4ee35609f78b932bd50feed639c29e64997e@changeid
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mmc: sunxi-mmc: Fix DMA descriptors allocated above 32 bits

commit e9f3fb523dbf476dc86beea23f5b5ca8f9687c93 upstream.

Newer variants of the MMC controller support a 34-bit physical address
space by using word addresses instead of byte addresses. However, the
code truncates the DMA descriptor address to 32 bits before applying the
shift. This breaks DMA for descriptors allocated above the 32-bit limit.

Fixes: 3536b82e5853 ("mmc: sunxi: add support for A100 mmc controller")
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20220424231751.32053-1-samuel@sholland.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mmc: sdhci-msm: Reset GCC_SDCC_BCR register for SDHC

commit 3e5a8e8494a8122fe4eb3f167662f406cab753b9 upstream.

Reset GCC_SDCC_BCR register before every fresh initilazation. This will
reset whole SDHC-msm controller, clears the previous power control
states and avoids, software reset timeout issues as below.

[ 5.458061][ T262] mmc1: Reset 0x1 never completed.
[ 5.462454][ T262] mmc1: sdhci: ============ SDHCI REGISTER DUMP ===========
[ 5.469065][ T262] mmc1: sdhci: Sys addr: 0x00000000 | Version: 0x00007202
[ 5.475688][ T262] mmc1: sdhci: Blk size: 0x00000000 | Blk cnt: 0x00000000
[ 5.482315][ T262] mmc1: sdhci: Argument: 0x00000000 | Trn mode: 0x00000000
[ 5.488927][ T262] mmc1: sdhci: Present: 0x01f800f0 | Host ctl: 0x00000000
[ 5.495539][ T262] mmc1: sdhci: Power: 0x00000000 | Blk gap: 0x00000000
[ 5.502162][ T262] mmc1: sdhci: Wake-up: 0x00000000 | Clock: 0x00000003
[ 5.508768][ T262] mmc1: sdhci: Timeout: 0x00000000 | Int stat: 0x00000000
[ 5.515381][ T262] mmc1: sdhci: Int enab: 0x00000000 | Sig enab: 0x00000000
[ 5.521996][ T262] mmc1: sdhci: ACmd stat: 0x00000000 | Slot int: 0x00000000
[ 5.528607][ T262] mmc1: sdhci: Caps: 0x362dc8b2 | Caps_1: 0x0000808f
[ 5.535227][ T262] mmc1: sdhci: Cmd: 0x00000000 | Max curr: 0x00000000
[ 5.541841][ T262] mmc1: sdhci: Resp[0]: 0x00000000 | Resp[1]: 0x00000000
[ 5.548454][ T262] mmc1: sdhci: Resp[2]: 0x00000000 | Resp[3]: 0x00000000
[ 5.555079][ T262] mmc1: sdhci: Host ctl2: 0x00000000
[ 5.559651][ T262] mmc1: sdhci_msm: ----------- VENDOR REGISTER DUMP-----------
[ 5.566621][ T262] mmc1: sdhci_msm: DLL sts: 0x00000000 | DLL cfg: 0x6000642c | DLL cfg2: 0x0020a000
[ 5.575465][ T262] mmc1: sdhci_msm: DLL cfg3: 0x00000000 | DLL usr ctl: 0x00010800 | DDR cfg: 0x80040873
[ 5.584658][ T262] mmc1: sdhci_msm: Vndr func: 0x00018a9c | Vndr func2 : 0xf88218a8 Vndr func3: 0x02626040

Fixes: 0eb0d9f4de34 ("mmc: sdhci-msm: Initial support for Qualcomm chipsets")
Signed-off-by: Shaik Sajida Bhanu <quic_c_sbhanu@quicinc.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Tested-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/1650816153-23797-1-git-send-email-quic_c_sbhanu@quicinc.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ALSA: fireworks: fix wrong return count shorter than expected by 4 bytes

commit eb9d84b0ffe39893cb23b0b6712bbe3637fa25fa upstream.

ALSA fireworks driver has a bug in its initial state to return count
shorter than expected by 4 bytes to userspace applications when handling
response frame for Echo Audio Fireworks transaction. It's due to missing
addition of the size for the type of event in ALSA firewire stack.

Fixes: 555e8a8f7f14 ("ALSA: fireworks: Add command/response functionality into hwdep interface")
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20220424102428.21109-1-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ALSA: hda/realtek: Add quirk for Yoga Duet 7 13ITL6 speakers

commit 3b79954fd00d540677c97a560622b73f3a1f4e28 upstream.

Lenovo Yoga Duet 7 13ITL6 has Realtek ALC287 and built-in
speakers do not work out of the box. The fix developed for
Yoga 7i 14ITL5 also enables speaker output for this model.

Signed-off-by: Zihao Wang <wzhd@ustc.edu>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220424084120.74125-1-wzhd@ustc.edu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

parisc: Merge model and model name into one line in /proc/cpuinfo

commit 5b89966bc96a06f6ad65f64ae4b0461918fcc9d3 upstream.

The Linux tool "lscpu" shows the double amount of CPUs if we have
"model" and "model name" in two different lines in /proc/cpuinfo.
This change combines the model and the model name into one line.

Signed-off-by: Helge Deller <deller@gmx.de>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

MIPS: Fix CP0 counter erratum detection for R4k CPUs

commit f0a6c68f69981214cb7858738dd2bc81475111f7 upstream.

Fix the discrepancy between the two places we check for the CP0 counter
erratum in along with the incorrect comparison of the R4400 revision
number against 0x30 which matches none and consistently consider all
R4000 and R4400 processors affected, as documented in processor errata
publications[1][2][3], following the mapping between CP0 PRId register
values and processor models:

  PRId   |  Processor Model
---------+--------------------
00000422 | R4000 Revision 2.2
00000430 | R4000 Revision 3.0
00000440 | R4400 Revision 1.0
00000450 | R4400 Revision 2.0
00000460 | R4400 Revision 3.0

No other revision of either processor has ever been spotted.

Contrary to what has been stated in commit ce202cbb9e0b ("[MIPS] Assume
R4000/R4400 newer than 3.0 don't have the mfc0 count bug") marking the
CP0 counter as buggy does not preclude it from being used as either a
clock event or a clock source device.  It just cannot be used as both at
a time, because in that case clock event interrupts will be occasionally
lost, and the use as a clock event device takes precedence.

Compare against 0x4ff in `can_use_mips_counter' so that a single machine
instruction is produced.

References:

[1] "MIPS R4000PC/SC Errata, Processor Revision 2.2 and 3.0", MIPS
    Technologies Inc., May 10, 1994, Erratum 53, p.13

[2] "MIPS R4400PC/SC Errata, Processor Revision 1.0", MIPS Technologies
    Inc., February 9, 1994, Erratum 21, p.4

[3] "MIPS R4400PC/SC Errata, Processor Revision 2.0 & 3.0", MIPS
    Technologies Inc., January 24, 1995, Erratum 14, p.3

Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Fixes: ce202cbb9e0b ("[MIPS] Assume R4000/R4400 newer than 3.0 don't have the mfc0 count bug")
Cc: stable@vger.kernel.org # v2.6.24+
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Linux 5.15.38

Link: https://lore.kernel.org/r/20220504153053.873100034@linuxfoundation.org
Tested-by: Ron Economos <re@w6rz.net>
Tested-by: Linux Kernel Functional Testing <lkft@linaro.org>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

powerpc/64: Add UADDR64 relocation support

commit d799769188529abc6cbf035a10087a51f7832b6b upstream.

When ld detects unaligned relocations, it emits R_PPC64_UADDR64
relocations instead of R_PPC64_RELATIVE. Currently R_PPC64_UADDR64 are
detected by arch/powerpc/tools/relocs_check.sh and expected not to work.
Below is a simple chunk to trigger this behaviour (this disables
optimization for the demonstration purposes only, this also happens with
-O1/-O2 when CONFIG_PRINTK_INDEX=y, for example):

  \#pragma GCC push_options
  \#pragma GCC optimize ("O0")
  struct entry {
          const char *file;
          int line;
  } __attribute__((packed));
  static const struct entry e1 = { .file = __FILE__, .line = __LINE__ };
  static const struct entry e2 = { .file = __FILE__, .line = __LINE__ };
  ...
  prom_printf("e1=%s %lx %lx\n", e1.file, (unsigned long) e1.file, mfmsr());
  prom_printf("e2=%s %lx\n", e2.file, (unsigned long) e2.file);
  \#pragma GCC pop_options

This adds support for UADDR64 for 64bit. This reuses __dynamic_symtab
from the 32bit code which supports more relocation types already.

Because RELACOUNT includes only R_PPC64_RELATIVE, this replaces it with
RELASZ which is the size of all relocation records.

Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Cc: Nathan Chancellor <nathan@kernel.org>
Link: https://lore.kernel.org/r/20220309061822.168173-1-aik@ozlabs.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

objtool: Fix type of reloc::addend

commit c087c6e7b551b7f208c0b852304f044954cf2bb3 upstream.

Elf{32,64}_Rela::r_addend is of type: Elf{32,64}_Sword, that means
that our reloc::addend needs to be long or face tuncation issues when
we do elf_rebuild_reloc_section():

  - 107:  48 b8 00 00 00 00 00 00 00 00   movabs $0x0,%rax        109: R_X86_64_64        level4_kernel_pgt+0x80000067
  + 107:  48 b8 00 00 00 00 00 00 00 00   movabs $0x0,%rax        109: R_X86_64_64        level4_kernel_pgt-0x7fffff99

Fixes: 627fce14809b ("objtool: Add ORC unwind table generation")
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Josh Poimboeuf <jpoimboe@redhat.com>
Link: https://lkml.kernel.org/r/20220419203807.596871927@infradead.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

objtool: Fix code relocs vs weak symbols

commit 4abff6d48dbcea8200c7ea35ba70c242d128ebf3 upstream.

Occasionally objtool driven code patching (think .static_call_sites
.retpoline_sites etc..) goes sideways and it tries to patch an
instruction that doesn't match.

Much head-scatching and cursing later the problem is as outlined below
and affects every section that objtool generates for us, very much
including the ORC data. The below uses .static_call_sites because it's
convenient for demonstration purposes, but as mentioned the ORC
sections, .retpoline_sites and __mount_loc are all similarly affected.

Consider:

foo-weak.c:

  extern void __SCT__foo(void);

  __attribute__((weak)) void foo(void)
  {
  return __SCT__foo();
  }

foo.c:

  extern void __SCT__foo(void);
  extern void my_foo(void);

  void foo(void)
  {
  my_foo();
  return __SCT__foo();
  }

These generate the obvious code
(gcc -O2 -fcf-protection=none -fno-asynchronous-unwind-tables -c foo*.c):

foo-weak.o:
0000000000000000 <foo>:
   0:   e9 00 00 00 00          jmpq   5 <foo+0x5>      1: R_X86_64_PLT32       __SCT__foo-0x4

foo.o:
0000000000000000 <foo>:
   0:   48 83 ec 08             sub    $0x8,%rsp
   4:   e8 00 00 00 00          callq  9 <foo+0x9>      5: R_X86_64_PLT32       my_foo-0x4
   9:   48 83 c4 08             add    $0x8,%rsp
   d:   e9 00 00 00 00          jmpq   12 <foo+0x12>    e: R_X86_64_PLT32       __SCT__foo-0x4

Now, when we link these two files together, you get something like
(ld -r -o foos.o foo-weak.o foo.o):

foos.o:
0000000000000000 <foo-0x10>:
   0:   e9 00 00 00 00          jmpq   5 <foo-0xb>      1: R_X86_64_PLT32       __SCT__foo-0x4
   5:   66 2e 0f 1f 84 00 00 00 00 00   nopw   %cs:0x0(%rax,%rax,1)
   f:   90                      nop

0000000000000010 <foo>:
  10:   48 83 ec 08             sub    $0x8,%rsp
  14:   e8 00 00 00 00          callq  19 <foo+0x9>     15: R_X86_64_PLT32      my_foo-0x4
  19:   48 83 c4 08             add    $0x8,%rsp
  1d:   e9 00 00 00 00          jmpq   22 <foo+0x12>    1e: R_X86_64_PLT32      __SCT__foo-0x4

Noting that ld preserves the weak function text, but strips the symbol
off of it (hence objdump doing that funny negative offset thing). This
does lead to 'interesting' unused code issues with objtool when ran on
linked objects, but that seems to be working (fingers crossed).

So far so good.. Now lets consider the objtool static_call output
section (readelf output, old binutils):

foo-weak.o:

Relocation section '.rela.static_call_sites' at offset 0x2c8 contains 1 entry:
    Offset             Info             Type               Symbol's Value  Symbol's Name + Addend
0000000000000000  0000000200000002 R_X86_64_PC32          0000000000000000 .text + 0
0000000000000004  0000000d00000002 R_X86_64_PC32          0000000000000000 __SCT__foo + 1

foo.o:

Relocation section '.rela.static_call_sites' at offset 0x310 contains 2 entries:
    Offset             Info             Type               Symbol's Value  Symbol's Name + Addend
0000000000000000  0000000200000002 R_X86_64_PC32          0000000000000000 .text + d
0000000000000004  0000000d00000002 R_X86_64_PC32          0000000000000000 __SCT__foo + 1

foos.o:

Relocation section '.rela.static_call_sites' at offset 0x430 contains 4 entries:
    Offset             Info             Type               Symbol's Value  Symbol's Name + Addend
0000000000000000  0000000100000002 R_X86_64_PC32          0000000000000000 .text + 0
0000000000000004  0000000d00000002 R_X86_64_PC32          0000000000000000 __SCT__foo + 1
0000000000000008  0000000100000002 R_X86_64_PC32          0000000000000000 .text + 1d
000000000000000c  0000000d00000002 R_X86_64_PC32          0000000000000000 __SCT__foo + 1

So we have two patch sites, one in the dead code of the weak foo and one
in the real foo. All is well.

*HOWEVER*, when the toolchain strips unused section symbols it
generates things like this (using new enough binutils):

foo-weak.o:

Relocation section '.rela.static_call_sites' at offset 0x2c8 contains 1 entry:
    Offset             Info             Type               Symbol's Value  Symbol's Name + Addend
0000000000000000  0000000200000002 R_X86_64_PC32          0000000000000000 foo + 0
0000000000000004  0000000d00000002 R_X86_64_PC32          0000000000000000 __SCT__foo + 1

foo.o:

Relocation section '.rela.static_call_sites' at offset 0x310 contains 2 entries:
    Offset             Info             Type               Symbol's Value  Symbol's Name + Addend
0000000000000000  0000000200000002 R_X86_64_PC32          0000000000000000 foo + d
0000000000000004  0000000d00000002 R_X86_64_PC32          0000000000000000 __SCT__foo + 1

foos.o:

Relocation section '.rela.static_call_sites' at offset 0x430 contains 4 entries:
    Offset             Info             Type               Symbol's Value  Symbol's Name + Addend
0000000000000000  0000000100000002 R_X86_64_PC32          0000000000000000 foo + 0
0000000000000004  0000000d00000002 R_X86_64_PC32          0000000000000000 __SCT__foo + 1
0000000000000008  0000000100000002 R_X86_64_PC32          0000000000000000 foo + d
000000000000000c  0000000d00000002 R_X86_64_PC32          0000000000000000 __SCT__foo + 1

And now we can see how that foos.o .static_call_sites goes side-ways, we
now have _two_ patch sites in foo. One for the weak symbol at foo+0
(which is no longer a static_call site!) and one at foo+d which is in
fact the right location.

This seems to happen when objtool cannot find a section symbol, in which
case it falls back to any other symbol to key off of, however in this
case that goes terribly wrong!

As such, teach objtool to create a section symbol when there isn't
one.

Fixes: 44f6a7c0755d ("objtool: Fix seg fault with Clang non-section symbols")
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Josh Poimboeuf <jpoimboe@redhat.com>
Link: https://lkml.kernel.org/r/20220419203807.655552918@infradead.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

eeprom: at25: Use DMA safe buffers

commit 5b47b751b760ee1c74a51660fd096aa148a362cd upstream.

Reading EEPROM fails with following warning:

[   16.357496] ------------[ cut here ]------------
[   16.357529] fsl_spi b01004c0.spi: rejecting DMA map of vmalloc memory
[   16.357698] WARNING: CPU: 0 PID: 371 at include/linux/dma-mapping.h:326 fsl_spi_cpm_bufs+0x2a0/0x2d8
[   16.357775] CPU: 0 PID: 371 Comm: od Not tainted 5.16.11-s3k-dev-01743-g19beecbfe9d6-dirty #109
[   16.357806] NIP:  c03fbc9c LR: c03fbc9c CTR: 00000000
[   16.357825] REGS: e68d9b20 TRAP: 0700   Not tainted  (5.16.11-s3k-dev-01743-g19beecbfe9d6-dirty)
[   16.357849] MSR:  00029032 <EE,ME,IR,DR,RI>  CR: 24002282  XER: 00000000
[   16.357931]
[   16.357931] GPR00: c03fbc9c e68d9be0 c26d06a0 00000039 00000001 c0d36364 c0e96428 00000027
[   16.357931] GPR08: 00000001 00000000 00000023 3fffc000 24002282 100d3dd6 100a2ffc 00000000
[   16.357931] GPR16: 100cd280 100b0000 00000000 aff54f7e 100d0000 100d0000 00000001 100cf328
[   16.357931] GPR24: 100cf328 00000000 00000003 e68d9e30 c156b410 e67ab4c0 e68d9d38 c24ab278
[   16.358253] NIP [c03fbc9c] fsl_spi_cpm_bufs+0x2a0/0x2d8
[   16.358292] LR [c03fbc9c] fsl_spi_cpm_bufs+0x2a0/0x2d8
[   16.358325] Call Trace:
[   16.358336] [e68d9be0] [c03fbc9c] fsl_spi_cpm_bufs+0x2a0/0x2d8 (unreliable)
[   16.358388] [e68d9c00] [c03fcb44] fsl_spi_bufs.isra.0+0x94/0x1a0
[   16.358436] [e68d9c20] [c03fd970] fsl_spi_do_one_msg+0x254/0x3dc
[   16.358483] [e68d9cb0] [c03f7e50] __spi_pump_messages+0x274/0x8a4
[   16.358529] [e68d9ce0] [c03f9d30] __spi_sync+0x344/0x378
[   16.358573] [e68d9d20] [c03fb52c] spi_sync+0x34/0x60
[   16.358616] [e68d9d30] [c03b4dec] at25_ee_read+0x138/0x1a8
[   16.358667] [e68d9e50] [c04a8fb8] bin_attr_nvmem_read+0x98/0x110
[   16.358725] [e68d9e60] [c0204b14] kernfs_fop_read_iter+0xc0/0x1fc
[   16.358774] [e68d9e80] [c0168660] vfs_read+0x284/0x410
[   16.358821] [e68d9f00] [c016925c] ksys_read+0x6c/0x11c
[   16.358863] [e68d9f30] [c00160e0] ret_from_syscall+0x0/0x28
...
[   16.359608] ---[ end trace a4ce3e34afef0cb5 ]---
[   16.359638] fsl_spi b01004c0.spi: unable to map tx dma

This is due to the AT25 driver using buffers on stack, which is not
possible with CONFIG_VMAP_STACK.

As mentionned in kernel Documentation (Documentation/spi/spi-summary.rst):

  - Follow standard kernel rules, and provide DMA-safe buffers in
    your messages.  That way controller drivers using DMA aren't forced
    to make extra copies unless the hardware requires it (e.g. working
    around hardware errata that force the use of bounce buffering).

Modify the driver to use a buffer located in the at25 device structure
which is allocated via kmalloc during probe.

Protect writes in this new buffer with the driver's mutex.

Fixes: b587b13a4f67 ("[PATCH] SPI eeprom driver")
Cc: stable <stable@kernel.org>
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Link: https://lore.kernel.org/r/230a9486fc68ea0182df46255e42a51099403642.1648032613.git.christophe.leroy@csgroup.eu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

perf symbol: Remove arch__symbols__fixup_end()

commit a5d20d42a2f2dc2b2f9e9361912062732414090d upstream.

Now the generic code can handle kallsyms fixup properly so no need to
keep the arch-functions anymore.

Fixes: 3cf6a32f3f2a4594 ("perf symbols: Fix symbol size calculation condition")
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Acked-by: Ian Rogers <irogers@google.com>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: John Garry <john.garry@huawei.com>
Cc: Leo Yan <leo.yan@linaro.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michael Petlan <mpetlan@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Song Liu <songliubraving@fb.com>
Cc: Will Deacon <will@kernel.org>
Cc: linux-s390@vger.kernel.org
Cc: linuxppc-dev@lists.ozlabs.org
Link: https://lore.kernel.org/r/20220416004048.1514900-4-namhyung@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tty: n_gsm: fix software flow control handling

commit f4f7d63287217ba25e5c80f5faae5e4f7118790e upstream.

n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010.
See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516
The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to
the newer 27.010 here. Chapter 5.4.8.1 states that XON/XOFF characters
shall be used instead of Fcon/Fcoff command in advanced option mode to
handle flow control. Chapter 5.4.8.2 describes how XON/XOFF characters
shall be handled. Basic option mode only used Fcon/Fcoff commands and no
XON/XOFF characters. These are treated as data bytes here.
The current implementation uses the gsm_mux field 'constipated' to handle
flow control from the remote peer and the gsm_dlci field 'constipated' to
handle flow control from each DLCI. The later is unrelated to this patch.
The gsm_mux field is correctly set for Fcon/Fcoff commands in
gsm_control_message(). However, the same is not true for XON/XOFF
characters in gsm1_receive().
Disable software flow control handling in the tty to allow explicit
handling by n_gsm.
Add the missing handling in advanced option mode for gsm_mux in
gsm1_receive() to comply with the standard.

This patch depends on the following commit:
Commit 8838b2af23ca ("tty: n_gsm: fix SW flow control encoding/handling")

Fixes: e1eaea46bb40 ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220422071025.5490-3-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tty: n_gsm: fix incorrect UA handling

commit ff9166c623704337bd6fe66fce2838d9768a6634 upstream.

n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010.
See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516
The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to
the newer 27.010 here. Chapter 5.4.4.2 states that any received unnumbered
acknowledgment (UA) with its poll/final (PF) bit set to 0 shall be
discarded. Currently, all UA frame are handled in the same way regardless
of the PF bit. This does not comply with the standard.
Remove the UA case in gsm_queue() to process only UA frames with PF bit set
to 1 to abide the standard.

Fixes: e1eaea46bb40 ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220414094225.4527-20-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tty: n_gsm: fix reset fifo race condition

commit 73029a4d7161f8b6c0934553145ef574d2d0c645 upstream.

gsmtty_write() and gsm_dlci_data_output() properly guard the fifo access.
However, gsm_dlci_close() and gsmtty_flush_buffer() modifies the fifo but
do not guard this.
Add a guard here to prevent race conditions on parallel writes to the fifo.

Fixes: e1eaea46bb40 ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220414094225.4527-17-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tty: n_gsm: fix missing tty wakeup in convergence layer type 2

commit 1adf6fee58ca25fb6720b8d34c919dcf5425cc9c upstream.

gsm_control_modem() informs the virtual tty that more data can be written
after receiving a control signal octet via modem status command (MSC).
However, gsm_dlci_data() fails to do the same after receiving a control
signal octet from the convergence layer type 2 header.
Add tty_wakeup() in gsm_dlci_data() for convergence layer type 2 to fix
this.

Fixes: e1eaea46bb40 ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220414094225.4527-14-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tty: n_gsm: fix wrong signal octets encoding in MSC

commit 317f86af7f5d19f286ed2d181cbaef4a188c7f19 upstream.

n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010.
See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516
The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to
the newer 27.010 here. The value of the modem status command (MSC) frame
contains an address field, control signal and optional break signal octet.
The address field is encoded as described in chapter 5.2.1.2 with only one
octet (may be extended to more in future versions of the standard). Whereas
the control signal and break signal octet are always one byte each. This is
strange at first glance as it makes the EA bit redundant. However, the same
two octets are also encoded as header in convergence layer type 2 as
described in chapter 5.5.2. No header length field is given and the only
way to test if there is an optional break signal octet is via the EA flag
which extends the control signal octet with a break signal octet. Now it
becomes obvious how the EA bit for those two octets shall be encoded in the
MSC frame. The current implementation treats the signal octet different for
MSC frame and convergence layer type 2 header even though the standard
describes it for both in the same way.
Use the EA bit to encode the signal octets not only in the convergence
layer type 2 header but also in the MSC frame in the same way with either
1 or 2 bytes in case of an optional break signal. Adjust the receiving path
accordingly in gsm_control_modem().

Fixes: 3ac06b905655 ("tty: n_gsm: Fix for modems with brk in modem status control")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220414094225.4527-13-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tty: n_gsm: fix wrong command frame length field encoding

commit 398867f59f956985f4c324f173eff7b946e14bd8 upstream.

n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010.
See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516
The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to
the newer 27.010 here. Chapter 5.4.6.1 states that each command frame shall
be made up from type, length and value. Looking for example in chapter
5.4.6.3.5 at the description for the encoding of a flow control on command
it becomes obvious, that the type and length field is always present
whereas the value may be zero bytes long. The current implementation omits
the length field if the value is not present. This is wrong.
Correct this by always sending the length in gsm_control_transmit().
So far only the modem status command (MSC) has included a value and encoded
its length directly. Therefore, also change gsmtty_modem_update().

Fixes: e1eaea46bb40 ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220414094225.4527-12-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tty: n_gsm: fix wrong command retry handling

commit d0bcdffcad5a22f202e3bf37190c0dd8c080ea92 upstream.

n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010.
See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516
The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to
the newer 27.010 here. Chapter 5.7.3 states that the valid range for the
maximum number of retransmissions (N2) is from 0 to 255 (both including).
gsm_config() fails to limit this range correctly. Furthermore,
gsm_control_retransmit() handles this number incorrectly by performing
N2 - 1 retransmission attempts. Setting N2 to zero results in more than 255
retransmission attempts.
Fix the range check in gsm_config() and the value handling in
gsm_control_send() and gsm_control_retransmit() to comply with 3GPP 27.010.

Fixes: e1eaea46bb40 ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220414094225.4527-11-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tty: n_gsm: fix missing explicit ldisc flush

commit 17eac652028501df7ea296b1d9b9c134db262b7d upstream.

In gsm_cleanup_mux() the muxer is closed down and all queues are removed.
However, removing the queues is done without explicit control of the
underlying buffers. Flush those before freeing up our queues to ensure
that all outgoing queues are cleared consistently. Otherwise, a new mux
connection establishment attempt may time out while the underlying tty is
still busy sending out the remaining data from the previous connection.

Fixes: e1eaea46bb40 ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220414094225.4527-10-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tty: n_gsm: fix wrong DLCI release order

commit deefc58bafb4841df7f0a0d85d89a1c819db9743 upstream.

The current DLCI release order starts with the control channel followed by
the user channels. Reverse this order to keep the control channel open
until all user channels have been released.

Fixes: e1eaea46bb40 ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220414094225.4527-9-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tty: n_gsm: fix insufficient txframe size

commit 535bf600de75a859698892ee873521a48d289ec1 upstream.

n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010.
See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516
The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to
the newer 27.010 here. Chapter 5.7.2 states that the maximum frame size
(N1) refers to the length of the information field (i.e. user payload).
However, 'txframe' stores the whole frame including frame header, checksum
and start/end flags. We also need to consider the byte stuffing overhead.
Define constant for the protocol overhead and adjust the 'txframe' size
calculation accordingly to reserve enough space for a complete mux frame
including byte stuffing for advanced option mode. Note that no byte
stuffing is applied to the start and end flag.
Also use MAX_MTU instead of MAX_MRU as this buffer is used for data
transmission.

Fixes: e1eaea46bb40 ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220414094225.4527-8-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

netfilter: nft_socket: only do sk lookups when indev is available

commit 743b83f15d4069ea57c3e40996bf4a1077e0cdc1 upstream.

Check if the incoming interface is available and NFT_BREAK
in case neither skb->sk nor input device are set.

Because nf_sk_lookup_slow*() assume packet headers are in the
'in' direction, use in postrouting is not going to yield a meaningful
result.  Same is true for the forward chain, so restrict the use
to prerouting, input and output.

Use in output work if a socket is already attached to the skb.

Fixes: 554ced0a6e29 ("netfilter: nf_tables: add support for native socket matching")
Reported-and-tested-by: Topi Miettinen <toiwoton@gmail.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tty: n_gsm: fix malformed counter for out of frame data

commit a24b4b2f660b7ddf3f484b37600bba382cb28a9d upstream.

The gsm_mux field 'malformed' represents the number of malformed frames
received. However, gsm1_receive() also increases this counter for any out
of frame byte.
Fix this by ignoring out of frame data for the malformed counter.

Fixes: e1eaea46bb40 ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220414094225.4527-7-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tty: n_gsm: fix wrong signal octet encoding in convergence layer type 2

commit 06d5afd4d640eea67f5623e76cd5fc03359b7f3c upstream.

n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010.
See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516
The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to
the newer 27.010 here. Chapter 5.5.2 describes that the signal octet in
convergence layer type 2 can be either one or two bytes. The length is
encoded in the EA bit. This is set 1 for the last byte in the sequence.
gsmtty_modem_update() handles this correctly but gsm_dlci_data_output()
fails to set EA to 1. There is no case in which we encode two signal octets
as there is no case in which we send out a break signal.
Therefore, always set the EA bit to 1 for the signal octet to fix this.

Fixes: e1eaea46bb40 ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220414094225.4527-5-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tty: n_gsm: fix mux cleanup after unregister tty device

commit 284260f278b706364fb4c88a7b56ba5298d5973c upstream.

Internally, we manage the alive state of the mux channels and mux itself
with the field member 'dead'. This makes it possible to notify the user
if the accessed underlying link is already gone. On the other hand,
however, removing the virtual ttys before terminating the channels may
result in peer messages being received without any internal target. Move
the mux cleanup procedure from gsmld_detach_gsm() to gsmld_close() to fix
this by keeping the virtual ttys open until the mux has been cleaned up.

Fixes: e1eaea46bb40 ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220414094225.4527-4-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tty: n_gsm: fix decoupled mux resource

commit 1ec92e9742774bf42614fceea3bf6b50c9409225 upstream.

The active mux instances are managed in the gsm_mux array and via mux_get()
and mux_put() functions separately. This gives a very loose coupling
between the actual instance and the gsm_mux array which manages it. It also
results in unnecessary lockings which makes it prone to failures. And it
creates a race condition if more than the maximum number of mux instances
are requested while the user changes the parameters of an active instance.
The user may loose ownership of the current mux instance in this case.
Fix this by moving the gsm_mux array handling to the mux allocation and
deallocation functions.

Fixes: e1eaea46bb40 ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220414094225.4527-3-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tty: n_gsm: fix restart handling via CLD command

commit aa371e96f05dcb36a88298f5cb70aa7234d5e8b8 upstream.

n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010.
See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516
The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to
the newer 27.010 here. Chapter 5.8.2 states that both sides will revert to
the non-multiplexed mode via a close-down message (CLD). The usual program
flow is as following:
- start multiplex mode by sending AT+CMUX to the mobile
- establish the control channel (DLCI 0)
- establish user channels (DLCI >0)
- terminate user channels
- send close-down message (CLD)
- revert to AT protocol (i.e. leave multiplexed mode)

The AT protocol is out of scope of the n_gsm driver. However,
gsm_disconnect() sends CLD if gsm_config() detects that the requested
parameters require the mux protocol to restart. The next immediate action
is to start the mux protocol by opening DLCI 0 again. Any responder side
which handles CLD commands correctly forces us to fail at this point
because AT+CMUX needs to be sent to the mobile to start the mux again.
Therefore, remove the CLD command in this phase and keep both sides in
multiplexed mode.
Remove the gsm_disconnect() function as it become unnecessary and merge the
remaining parts into gsm_cleanup_mux() to handle the termination order and
locking correctly.

Fixes: 71e077915396 ("tty: n_gsm: do not send/receive in ldisc close path")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220414094225.4527-2-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

perf symbol: Update symbols__fixup_end()

commit 8799ebce84d672aae1dc3170510f6a3e66f96b11 upstream.

Now arch-specific functions all do the same thing.  When it fixes the
symbol address it needs to check the boundary between the kernel image
and modules.  For the last symbol in the previous region, it cannot
know the exact size as it's discarded already.  Thus it just uses a
small page size (4096) and rounds it up like the last symbol.

Fixes: 3cf6a32f3f2a4594 ("perf symbols: Fix symbol size calculation condition")
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Acked-by: Ian Rogers <irogers@google.com>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: John Garry <john.garry@huawei.com>
Cc: Leo Yan <leo.yan@linaro.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michael Petlan <mpetlan@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Song Liu <songliubraving@fb.com>
Cc: Will Deacon <will@kernel.org>
Cc: linux-s390@vger.kernel.org
Cc: linuxppc-dev@lists.ozlabs.org
Link: https://lore.kernel.org/r/20220416004048.1514900-3-namhyung@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

perf symbol: Pass is_kallsyms to symbols__fixup_end()

commit 838425f2defe5262906b698752d28fd2fca1aac2 upstream.

The symbol fixup is necessary for symbols in kallsyms since they don't
have size info.  So we use the next symbol's address to calculate the
size.  Now it's also used for user binaries because sometimes they miss
size for hand-written asm functions.

There's a arch-specific function to handle kallsyms differently but
currently it cannot distinguish kallsyms from others.  Pass this
information explicitly to handle it properly.  Note that those arch
functions will be moved to the generic function so I didn't added it to
the arch-functions.

Fixes: 3cf6a32f3f2a4594 ("perf symbols: Fix symbol size calculation condition")
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Acked-by: Ian Rogers <irogers@google.com>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: John Garry <john.garry@huawei.com>
Cc: Leo Yan <leo.yan@linaro.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michael Petlan <mpetlan@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Song Liu <songliubraving@fb.com>
Cc: Will Deacon <will@kernel.org>
Cc: linux-s390@vger.kernel.org
Cc: linuxppc-dev@lists.ozlabs.org
Link: https://lore.kernel.org/r/20220416004048.1514900-2-namhyung@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

x86/cpu: Load microcode during restore_processor_state()

commit f9e14dbbd454581061c736bf70bf5cbb15ac927c upstream.

When resuming from system sleep state, restore_processor_state()
restores the boot CPU MSRs. These MSRs could be emulated by microcode.
If microcode is not loaded yet, writing to emulated MSRs leads to
unchecked MSR access error:

  ...
  PM: Calling lapic_suspend+0x0/0x210
  unchecked MSR access error: WRMSR to 0x10f (tried to write 0x0...0) at rIP: ... (native_write_msr)
  Call Trace:
    <TASK>
    ? restore_processor_state
    x86_acpi_suspend_lowlevel
    acpi_suspend_enter
    suspend_devices_and_enter
    pm_suspend.cold
    state_store
    kobj_attr_store
    sysfs_kf_write
    kernfs_fop_write_iter
    new_sync_write
    vfs_write
    ksys_write
    __x64_sys_write
    do_syscall_64
    entry_SYSCALL_64_after_hwframe
   RIP: 0033:0x7fda13c260a7

To ensure microcode emulated MSRs are available for restoration, load
the microcode on the boot CPU before restoring these MSRs.

  [ Pawan: write commit message and productize it. ]

Fixes: e2a1256b17b1 ("x86/speculation: Restore speculation related MSRs during S3 resume")
Reported-by: Kyle D. Pelton <kyle.d.pelton@intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Pawan Gupta <pawan.kumar.gupta@linux.intel.com>
Tested-by: Kyle D. Pelton <kyle.d.pelton@intel.com>
Cc: stable@vger.kernel.org
Link: https://bugzilla.kernel.org/show_bug.cgi?id=215841
Link: https://lore.kernel.org/r/4350dfbf785cd482d3fafa72b2b49c83102df3ce.1650386317.git.pawan.kumar.gupta@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ARM: dts: imx8mm-venice-gw{71xx,72xx,73xx}: fix OTG controller OC mode

commit 4c79865f3e8a2db93ec1e844509edfebe5a6ae56 upstream.

The GW71xx, GW72xx and GW73xx boards have USB1 routed to a USB OTG
connectors and USB2 routed to a USB hub.

The OTG connector has a over-currently protection with an active-low
pin and the USB1 to HUB connection has no over-current protection (as
the HUB itself implements this for its downstream ports).

Add proper dt nodes to specify the over-current pin polarity for USB1
and disable over-current protection for USB2.

Fixes: 6f30b27c5ef5 ("arm64: dts: imx8mm: Add Gateworks i.MX 8M Mini Development Kits")
Cc: stable@vger.kernel.org
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ARM: dts: at91: sama7g5ek: enable pull-up on flexcom3 console lines

commit 3f7ce6d7091765ed6c67c5d78aa364b9d17e3aab upstream.

Flexcom3 is used as board console serial. There are no pull-ups on these
lines on the board. This means that if a cable is not connected (that has
pull-ups included), stray characters could appear on the console as the
floating pins voltage levels are interpreted as incoming characters.
To avoid this problem, enable the internal pull-ups on these lines.

Fixes: 7540629e2fc7 ("ARM: dts: at91: add sama7g5 SoC DT and sama7g5-ek")
Cc: stable@vger.kernel.org # v5.15+
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20220307113827.2419331-1-eugen.hristev@microchip.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

btrfs: fix leaked plug after failure syncing log on zoned filesystems

commit 50ff57888d0b13440e7f4cde05dc339ee8d0f1f8 upstream.

On a zoned filesystem, if we fail to allocate the root node for the log
root tree while syncing the log, we end up returning without finishing
the IO plug we started before, resulting in leaking resources as we
have started writeback for extent buffers of a log tree before. That
allocation failure, which typically is either -ENOMEM or -ENOSPC, is not
fatal and the fsync can safely fallback to a full transaction commit.

So release the IO plug if we fail to allocate the extent buffer for the
root of the log root tree when syncing the log on a zoned filesystem.

Fixes: 3ddebf27fcd3a9 ("btrfs: zoned: reorder log node allocation on zoned filesystem")
CC: stable@vger.kernel.org # 5.15+
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

thermal: int340x: Fix attr.show callback prototype

commit d0f6cfb2bd165b0aa307750e07e03420859bd554 upstream.

Control Flow Integrity (CFI) instrumentation of the kernel noticed that
the caller, dev_attr_show(), and the callback, odvp_show(), did not have
matching function prototypes, which would cause a CFI exception to be
raised. Correct the prototype by using struct device_attribute instead
of struct kobj_attribute.

Reported-and-tested-by: Joao Moreira <joao@overdrivepizza.com>
Link: https://lore.kernel.org/lkml/067ce8bd4c3968054509831fa2347f4f@overdrivepizza.com/
Fixes: 006f006f1e5c ("thermal/int340x_thermal: Export OEM vendor variables")
Cc: 5.8+ <stable@vger.kernel.org> # 5.8+
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ACPI: processor: idle: Avoid falling back to C3 type C-states

commit fc45e55ebc58dbf622cb89ddbf797589c7a5510b upstream.

The "safe state" index is used by acpi_idle_enter_bm() to avoid
entering a C-state that may require bus mastering to be disabled
on entry in the cases when this is not going to happen.  For this
reason, it should not be set to point to C3 type of C-states, because
they may require bus mastering to be disabled on entry in principle.

This was broken by commit d6b88ce2eb9d ("ACPI: processor idle: Allow
playing dead in C3 state") which inadvertently allowed the "safe
state" index to point to C3 type of C-states.

This results in a machine that won't boot past the point when it first
enters C3. Restore the correct behaviour (either demote to C1/C2, or
use C3 but also set ARB_DIS=1).

I hit this on a Fujitsu Siemens Lifebook S6010 (P3) machine.

Fixes: d6b88ce2eb9d ("ACPI: processor idle: Allow playing dead in C3 state")
Cc: 5.16+ <stable@vger.kernel.org> # 5.16+
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Woody Suwalski <wsuwalski@gmail.com>
[ rjw: Subject and changelog adjustments ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: ethernet: stmmac: fix write to sgmii_adapter_base

commit 5fd1fe4807f91ea0cca043114d929faa11bd4190 upstream.

I made a mistake with the commit a6aaa0032424 ("net: ethernet: stmmac:
fix altr_tse_pcs function when using a fixed-link"). I should have
tested against both scenario of having a SGMII interface and one
without.

Without the SGMII PCS TSE adpater, the sgmii_adapter_base address is
NULL, thus a write to this address will fail.

Cc: stable@vger.kernel.org
Fixes: a6aaa0032424 ("net: ethernet: stmmac: fix altr_tse_pcs function when using a fixed-link")
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Link: https://lore.kernel.org/r/20220420152345.27415-1-dinguyen@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/i915: Fix SEL_FETCH_PLANE_*(PIPE_B+) register addresses

commit 4ae4dd2e26fdfebf0b8c6af6c325383eadfefdb4 upstream.

Fix typo in the _SEL_FETCH_PLANE_BASE_1_B register base address.

Fixes: a5523e2ff074a5 ("drm/i915: Add PSR2 selective fetch registers")
References: https://gitlab.freedesktop.org/drm/intel/-/issues/5400
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: <stable@vger.kernel.org> # v5.9+
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220421162221.2261895-1-imre.deak@intel.com
(cherry picked from commit af2cbc6ef967f61711a3c40fca5366ea0bc7fecc)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/i915: Check EDID for HDR static metadata when choosing blc

commit c05d8332f5d23fa3b521911cbe55a2b67fb21248 upstream.

We have now seen panel (XMG Core 15 e21 laptop) advertizing support
for Intel proprietary eDP backlight control via DPCD registers, but
actually working only with legacy pwm control.

This patch adds panel EDID check for possible HDR static metadata and
Intel proprietary eDP backlight control is used only if that exists.
Missing HDR static metadata is ignored if user specifically asks for
Intel proprietary eDP backlight control via enable_dpcd_backlight
parameter.

v2 :
- Ignore missing HDR static metadata if Intel proprietary eDP
  backlight control is forced via i915.enable_dpcd_backlight
- Printout info message if panel is missing HDR static metadata and
  support for Intel proprietary eDP backlight control is detected

Fixes: 4a8d79901d5b ("drm/i915/dp: Enable Intel's HDR backlight interface (only SDR for now)")
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/5284
Cc: Lyude Paul <lyude@redhat.com>
Cc: Mika Kahola <mika.kahola@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Filippo Falezza <filippo.falezza@outlook.it>
Cc: stable@vger.kernel.org
Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220413082826.120634-1-jouni.hogander@intel.com
Reviewed-by: Lyude Paul <lyude@redhat.com>
(cherry picked from commit b4b157577cb1de13bee8bebc3576f1de6799a921)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

netfilter: Update ip6_route_me_harder to consider L3 domain

commit 8ddffdb9442a9d60b4a6e679ac48d7d21403a674 upstream.

The commit referenced below fixed packet re-routing if Netfilter mangles
a routing key property of a packet and the packet is routed in a VRF L3
domain. The fix, however, addressed IPv4 re-routing, only.

This commit applies the same behavior for IPv6. While at it, untangle
the nested ternary operator to make the code more readable.

Fixes: 6d8b49c3a3a3 ("netfilter: Update ip_route_me_harder to consider L3 domain")
Cc: stable@vger.kernel.org
Signed-off-by: Martin Willi <martin@strongswan.org>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mtd: rawnand: qcom: fix memory corruption that causes panic

commit ba7542eb2dd5dfc75c457198b88986642e602065 upstream.

This patch fixes a memory corruption that occurred in the
nand_scan() path for Hynix nand device.

On boot, for Hynix nand device will panic at a weird place:
| Unable to handle kernel NULL pointer dereference at virtual
  address 00000070
| [00000070] *pgd=00000000
| Internal error: Oops: 5 [#1] PREEMPT SMP ARM
| Modules linked in:
| CPU: 0 PID: 1 Comm: swapper/0 Not tainted 5.17.0-01473-g13ae1769cfb0
  #38
| Hardware name: Generic DT based system
| PC is at nandc_set_reg+0x8/0x1c
| LR is at qcom_nandc_command+0x20c/0x5d0
| pc : [<c088b74c>]    lr : [<c088d9c8>]    psr: 00000113
| sp : c14adc50  ip : c14ee208  fp : c0cc970c
| r10: 000000a3  r9 : 00000000  r8 : 00000040
| r7 : c16f6a00  r6 : 00000090  r5 : 00000004  r4 :c14ee040
| r3 : 00000000  r2 : 0000000b  r1 : 00000000  r0 :c14ee040
| Flags: nzcv  IRQs on  FIQs on  Mode SVC_32  ISA ARM Segment none
| Control: 10c5387d  Table: 8020406a  DAC: 00000051
| Register r0 information: slab kmalloc-2k start c14ee000 pointer offset
  64 size 2048
| Process swapper/0 (pid: 1, stack limit = 0x(ptrval))
| nandc_set_reg from qcom_nandc_command+0x20c/0x5d0
| qcom_nandc_command from nand_readid_op+0x198/0x1e8
| nand_readid_op from hynix_nand_has_valid_jedecid+0x30/0x78
| hynix_nand_has_valid_jedecid from hynix_nand_init+0xb8/0x454
| hynix_nand_init from nand_scan_with_ids+0xa30/0x14a8
| nand_scan_with_ids from qcom_nandc_probe+0x648/0x7b0
| qcom_nandc_probe from platform_probe+0x58/0xac

The problem is that the nand_scan()'s qcom_nand_attach_chip callback
is updating the nandc->max_cwperpage from 1 to 4 or 8 based on page size.
This causes the sg_init_table of clear_bam_transaction() in the driver's
qcom_nandc_command() to memset much more than what was initially
allocated by alloc_bam_transaction().

This patch will update nandc->max_cwperpage 1 to 4 or 8 based on page
size in qcom_nand_attach_chip call back after freeing the previously
allocated memory for bam txn as per nandc->max_cwperpage = 1 and then
again allocating bam txn as per nandc->max_cwperpage = 4 or 8 based on
page size in qcom_nand_attach_chip call back itself.

Cc: stable@vger.kernel.org
Fixes: 6a3cec64f18c ("mtd: rawnand: qcom: convert driver to nand_scan()")
Reported-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Co-developed-by: Sricharan R <quic_srichara@quicinc.com>
Signed-off-by: Sricharan R <quic_srichara@quicinc.com>
Signed-off-by: Md Sadre Alam <quic_mdalam@quicinc.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/1650268107-5363-1-git-send-email-quic_mdalam@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

kasan: prevent cpu_quarantine corruption when CPU offline and cache shrink occur at same time

commit 31fa985b4196f8a66f027672e9bf2b81fea0417c upstream.

kasan_quarantine_remove_cache() is called in kmem_cache_shrink()/
destroy().  The kasan_quarantine_remove_cache() call is protected by
cpuslock in kmem_cache_destroy() to ensure serialization with
kasan_cpu_offline().

However the kasan_quarantine_remove_cache() call is not protected by
cpuslock in kmem_cache_shrink().  When a CPU is going offline and cache
shrink occurs at same time, the cpu_quarantine may be corrupted by
interrupt (per_cpu_remove_cache operation).

So add a cpu_quarantine offline flags check in per_cpu_remove_cache().

[akpm@linux-foundation.org: add comment, per Zqiang]

Link: https://lkml.kernel.org/r/20220414025925.2423818-1-qiang1.zhang@intel.com
Signed-off-by: Zqiang <qiang1.zhang@intel.com>
Reviewed-by: Dmitry Vyukov <dvyukov@google.com>
Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com>
Cc: Alexander Potapenko <glider@google.com>
Cc: Andrey Konovalov <andreyknvl@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

zonefs: Clear inode information flags on inode creation

commit 694852ead287a3433126e7ebda397b242dc99624 upstream.

Ensure that the i_flags field of struct zonefs_inode_info is cleared to
0 when initializing a zone file inode, avoiding seeing the flag
ZONEFS_ZONE_OPEN being incorrectly set.

Fixes: b5c00e975779 ("zonefs: open/close zone on file open/close")
Cc: <stable@vger.kernel.org>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Reviewed-by: Hans Holmberg <hans.holmberg@wdc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

zonefs: Fix management of open zones

commit 1da18a296f5ba4f99429e62a7cf4fdbefa598902 upstream.

The mount option "explicit_open" manages the device open zone
resources to ensure that if an application opens a sequential file for
writing, the file zone can always be written by explicitly opening
the zone and accounting for that state with the s_open_zones counter.

However, if some zones are already open when mounting, the device open
zone resource usage status will be larger than the initial s_open_zones
value of 0. Ensure that this inconsistency does not happen by closing
any sequential zone that is open when mounting.

Furthermore, with ZNS drives, closing an explicitly open zone that has
not been written will change the zone state to "closed", that is, the
zone will remain in an active state. Since this can then cause failures
of explicit open operations on other zones if the drive active zone
resources are exceeded, we need to make sure that the zone is not
active anymore by resetting it instead of closing it. To address this,
zonefs_zone_mgmt() is modified to change a REQ_OP_ZONE_CLOSE request
into a REQ_OP_ZONE_RESET for sequential zones that have not been
written.

Fixes: b5c00e975779 ("zonefs: open/close zone on file open/close")
Cc: <stable@vger.kernel.org>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Hans Holmberg <hans.holmberg@wdc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Revert "ACPI: processor: idle: fix lockup regression on 32-bit ThinkPad T40"

commit 20e582e16af24b074e583f9551fad557882a3c9d upstream.

This reverts commit bfe55a1f7fd6bfede16078bf04c6250fbca11588.

This was presumably misdiagnosed as an inability to use C3 at
all when I suspect the real problem is just misconfiguration of
C3 vs. ARB_DIS.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: 5.16+ <stable@vger.kernel.org> # 5.16+
Tested-by: Woody Suwalski <wsuwalski@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

selftest/vm: verify remap destination address in mremap_test

[ Upstream commit 18d609daa546c919fd36b62a7b510c18de4b4af8 ]

Because mremap does not have a MAP_FIXED_NOREPLACE flag, it can destroy
existing mappings.  This causes a segfault when regions such as text are
remapped and the permissions are changed.

Verify the requested mremap destination address does not overlap any
existing mappings by using mmap's MAP_FIXED_NOREPLACE flag.  Keep
incrementing the destination address until a valid mapping is found or
fail the current test once the max address is reached.

Link: https://lkml.kernel.org/r/20220420215721.4868-2-sidhartha.kumar@oracle.com
Signed-off-by: Sidhartha Kumar <sidhartha.kumar@oracle.com>
Reviewed-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

selftest/vm: verify mmap addr in mremap_test

[ Upstream commit 9c85a9bae267f6b5e5e374d0d023bbbe9db096d3 ]

Avoid calling mmap with requested addresses that are less than the
system's mmap_min_addr.  When run as root, mmap returns EACCES when
trying to map addresses < mmap_min_addr.  This is not one of the error
codes for the condition to retry the mmap in the test.

Rather than arbitrarily retrying on EACCES, don't attempt an mmap until
addr > vm.mmap_min_addr.

Add a munmap call after an alignment check as the mappings are retained
after the retry and can reach the vm.max_map_count sysctl.

Link: https://lkml.kernel.org/r/20220420215721.4868-1-sidhartha.kumar@oracle.com
Signed-off-by: Sidhartha Kumar <sidhartha.kumar@oracle.com>
Reviewed-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

powerpc/perf: Fix 32bit compile

[ Upstream commit bb82c574691daf8f7fa9a160264d15c5804cb769 ]

The "read_bhrb" global symbol is only called under CONFIG_PPC64 of
arch/powerpc/perf/core-book3s.c but it is compiled for both 32 and 64 bit
anyway (and LLVM fails to link this on 32bit).

This fixes it by moving bhrb.o to obj64 targets.

Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20220421025756.571995-1-aik@ozlabs.ru
Signed-off-by: Sasha Levin <sashal@kernel.org>

drivers: net: hippi: Fix deadlock in rr_close()

[ Upstream commit bc6de2878429e85c1f1afaa566f7b5abb2243eef ]

There is a deadlock in rr_close(), which is shown below:

   (Thread 1)                |      (Thread 2)
                             | rr_open()
rr_close()                   |  add_timer()
 spin_lock_irqsave() //(1)   |  (wait a time)
 ...                         | rr_timer()
 del_timer_sync()            |  spin_lock_irqsave() //(2)
 (wait timer to stop)        |  ...

We hold rrpriv->lock in position (1) of thread 1 and
use del_timer_sync() to wait timer to stop, but timer handler
also need rrpriv->lock in position (2) of thread 2.
As a result, rr_close() will block forever.

This patch extracts del_timer_sync() from the protection of
spin_lock_irqsave(), which could let timer handler to obtain
the needed lock.

Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Link: https://lore.kernel.org/r/20220417125519.82618-1-duoming@zju.edu.cn
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

cifs: destage any unwritten data to the server before calling copychunk_write

[ Upstream commit f5d0f921ea362636e4a2efb7c38d1ead373a8700 ]

because the copychunk_write might cover a region of the file that has not yet
been sent to the server and thus fail.

A simple way to reproduce this is:
truncate -s 0 /mnt/testfile; strace -f -o x -ttT xfs_io -i -f -c 'pwrite 0k 128k' -c 'fcollapse 16k 24k' /mnt/testfile

the issue is that the 'pwrite 0k 128k' becomes rearranged on the wire with
the 'fcollapse 16k 24k' due to write-back caching.

fcollapse is implemented in cifs.ko as a SMB2 IOCTL(COPYCHUNK_WRITE) call
and it will fail serverside since the file is still 0b in size serverside
until the writes have been destaged.
To avoid this we must ensure that we destage any unwritten data to the
server before calling COPYCHUNK_WRITE.

Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1997373
Reported-by: Xiaoli Feng <xifeng@redhat.com>
Signed-off-by: Ronnie Sahlberg <lsahlber@redhat.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

x86: __memcpy_flushcache: fix wrong alignment if size > 2^32

[ Upstream commit a6823e4e360fe975bd3da4ab156df7c74c8b07f3 ]

The first "if" condition in __memcpy_flushcache is supposed to align the
"dest" variable to 8 bytes and copy data up to this alignment.  However,
this condition may misbehave if "size" is greater than 4GiB.

The statement min_t(unsigned, size, ALIGN(dest, 8) - dest); casts both
arguments to unsigned int and selects the smaller one.  However, the
cast truncates high bits in "size" and it results in misbehavior.

For example:

suppose that size == 0x100000001, dest == 0x200000002
min_t(unsigned, size, ALIGN(dest, 8) - dest) == min_t(0x1, 0xe) == 0x1;
...
dest += 0x1;

so we copy just one byte "and" dest remains unaligned.

This patch fixes the bug by replacing unsigned with size_t.

Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

bonding: do not discard lowest hash bit for non layer3+4 hashing

[ Upstream commit 49aefd131739df552f83c566d0665744c30b1d70 ]

Commit b5f862180d70 was introduced to discard lowest hash bit for layer3+4 hashing
but it also removes last bit from non layer3+4 hashing

Below script shows layer2+3 hashing will result in same slave to be used with above commit.
$ cat hash.py
#/usr/bin/python3.6

h_dests=[0xa0, 0xa1]
h_source=0xe3
hproto=0x8
saddr=0x1e7aa8c0
daddr=0x17aa8c0

for h_dest in h_dests:
    hash = (h_dest ^ h_source ^ hproto ^ saddr ^ daddr)
    hash ^= hash >> 16
    hash ^= hash >> 8
    print(hash)

print("with last bit removed")
for h_dest in h_dests:
    hash = (h_dest ^ h_source ^ hproto ^ saddr ^ daddr)
    hash ^= hash >> 16
    hash ^= hash >> 8
    hash = hash >> 1
    print(hash)

Output:
$ python3.6 hash.py
522133332
522133333   <-------------- will result in both slaves being used

with last bit removed
261066666
261066666   <-------------- only single slave used

Signed-off-by: suresh kumar <suresh2514@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ksmbd: set fixed sector size to FS_SECTOR_SIZE_INFORMATION

[ Upstream commit 02655a70b7cc0f534531ee65fa72692f4d31a944 ]

Currently ksmbd is using ->f_bsize from vfs_statfs() as sector size.
If fat/exfat is a local share, ->f_bsize is a cluster size that is too
large to be used as a sector size. Sector sizes larger than 4K cause
problem occurs when mounting an iso file through windows client.

The error message can be obtained using Mount-DiskImage command,
 the error is:
"Mount-DiskImage : The sector size of the physical disk on which the
virtual disk resides is not supported."

This patch reports fixed 4KB sector size if ->s_blocksize is bigger
than 4KB.

Signed-off-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ksmbd: increment reference count of parent fp

[ Upstream commit 8510a043d334ecdf83d4604782f288db6bf21d60 ]

Add missing increment reference count of parent fp in
ksmbd_lookup_fd_inode().

Signed-off-by: Namjae Jeon <linkinjeon@kernel.org>
Reviewed-by: Hyunchul Lee <hyc.lee@gmail.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

arch: xtensa: platforms: Fix deadlock in rs_close()

[ Upstream commit eb5adc70754d26a260f8b42d39db42da0d0af500 ]

There is a deadlock in rs_close(), which is shown
below:

   (Thread 1)              |      (Thread 2)
                           | rs_open()
rs_close()                 |  mod_timer()
 spin_lock_bh() //(1)      |  (wait a time)
 ...                       | rs_poll()
 del_timer_sync()          |  spin_lock() //(2)
 (wait timer to stop)      |  ...

We hold timer_lock in position (1) of thread 1 and
use del_timer_sync() to wait timer to stop, but timer handler
also need timer_lock in position (2) of thread 2.
As a result, rs_close() will block forever.

This patch deletes the redundant timer_lock in order to
prevent the deadlock. Because there is no race condition
between rs_close, rs_open and rs_poll.

Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Message-Id: <20220407154430.22387-1-duoming@zju.edu.cn>
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ext4: fix bug_on in start_this_handle during umount filesystem

[ Upstream commit b98535d091795a79336f520b0708457aacf55c67 ]

We got issue as follows:
------------[ cut here ]------------
kernel BUG at fs/jbd2/transaction.c:389!
invalid opcode: 0000 [#1] PREEMPT SMP KASAN PTI
CPU: 9 PID: 131 Comm: kworker/9:1 Not tainted 5.17.0-862.14.0.6.x86_64-00001-g23f87daf7d74-dirty #197
Workqueue: events flush_stashed_error_work
RIP: 0010:start_this_handle+0x41c/0x1160
RSP: 0018:ffff888106b47c20 EFLAGS: 00010202
RAX: ffffed10251b8400 RBX: ffff888128dc204c RCX: ffffffffb52972ac
RDX: 0000000000000200 RSI: 0000000000000004 RDI: ffff888128dc2050
RBP: 0000000000000039 R08: 0000000000000001 R09: ffffed10251b840a
R10: ffff888128dc204f R11: ffffed10251b8409 R12: ffff888116d78000
R13: 0000000000000000 R14: dffffc0000000000 R15: ffff888128dc2000
FS:  0000000000000000(0000) GS:ffff88839d680000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000001620068 CR3: 0000000376c0e000 CR4: 00000000000006e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
 <TASK>
 jbd2__journal_start+0x38a/0x790
 jbd2_journal_start+0x19/0x20
 flush_stashed_error_work+0x110/0x2b3
 process_one_work+0x688/0x1080
 worker_thread+0x8b/0xc50
 kthread+0x26f/0x310
 ret_from_fork+0x22/0x30
 </TASK>
Modules linked in:
---[ end trace 0000000000000000 ]---

Above issue may happen as follows:
      umount            read procfs            error_work
ext4_put_super
  flush_work(&sbi->s_error_work);

                      ext4_mb_seq_groups_show
                ext4_mb_load_buddy_gfp
  ext4_mb_init_group
    ext4_mb_init_cache
                      ext4_read_block_bitmap_nowait
        ext4_validate_block_bitmap
  ext4_error
            ext4_handle_error
              schedule_work(&EXT4_SB(sb)->s_error_work);

  ext4_unregister_sysfs(sb);
  jbd2_journal_destroy(sbi->s_journal);
    journal_kill_thread
      journal->j_flags |= JBD2_UNMOUNT;

                                          flush_stashed_error_work
            jbd2_journal_start
      start_this_handle
        BUG_ON(journal->j_flags & JBD2_UNMOUNT);

To solve this issue, we call 'ext4_unregister_sysfs() before flushing
s_error_work in ext4_put_super().

Signed-off-by: Ye Bin <yebin10@huawei.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Reviewed-by: Ritesh Harjani <riteshh@linux.ibm.com>
Link: https://lore.kernel.org/r/20220322012419.725457-1-yebin10@huawei.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ASoC: wm8731: Disable the regulator when probing fails

[ Upstream commit 92ccbf17eeacf510cf1eed9c252d9332ca24f02d ]

When the driver fails during probing, the driver should disable the
regulator, not just handle it in wm8731_hw_init().

The following log reveals it:

[   17.812483] WARNING: CPU: 1 PID: 364 at drivers/regulator/core.c:2257 _regulator_put+0x3ec/0x4e0
[   17.815958] RIP: 0010:_regulator_put+0x3ec/0x4e0
[   17.824467] Call Trace:
[   17.824774]  <TASK>
[   17.825040]  regulator_bulk_free+0x82/0xe0
[   17.825514]  devres_release_group+0x319/0x3d0
[   17.825882]  i2c_device_probe+0x766/0x940
[   17.829198]  i2c_register_driver+0xb5/0x130

Signed-off-by: Zheyu Ma <zheyuma97@gmail.com>
Link: https://lore.kernel.org/r/20220405121038.4094051-1-zheyuma97@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ASoC: Intel: soc-acpi: correct device endpoints for max98373

[ Upstream commit 97326be14df7bacc6ba5c62c0556298c27ea0432 ]

The left speaker of max98373 uses spk_r_endpoint, and right
speaker uses spk_l_endpoint, this is obviously wrong.

This patch corrects the endpoints for max98373 codec.

Signed-off-by: Chao Song <chao.song@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20220406192341.271465-1-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

tcp: fix F-RTO may not work correctly when receiving DSACK

[ Upstream commit d9157f6806d1499e173770df1f1b234763de5c79 ]

Currently DSACK is regarded as a dupack, which may cause
F-RTO to incorrectly enter "loss was real" when receiving
DSACK.

Packetdrill to demonstrate:

// Enable F-RTO and TLP
    0 `sysctl -q net.ipv4.tcp_frto=2`
    0 `sysctl -q net.ipv4.tcp_early_retrans=3`
    0 `sysctl -q net.ipv4.tcp_congestion_control=cubic`

// Establish a connection
   +0 socket(..., SOCK_STREAM, IPPROTO_TCP) = 3
   +0 setsockopt(3, SOL_SOCKET, SO_REUSEADDR, [1], 4) = 0
   +0 bind(3, ..., ...) = 0
   +0 listen(3, 1) = 0

// RTT 10ms, RTO 210ms
  +.1 < S 0:0(0) win 32792 <mss 1000,sackOK,nop,nop,nop,wscale 7>
   +0 > S. 0:0(0) ack 1 <...>
 +.01 < . 1:1(0) ack 1 win 257
   +0 accept(3, ..., ...) = 4

// Send 2 data segments
   +0 write(4, ..., 2000) = 2000
   +0 > P. 1:2001(2000) ack 1

// TLP
+.022 > P. 1001:2001(1000) ack 1

// Continue to send 8 data segments
   +0 write(4, ..., 10000) = 10000
   +0 > P. 2001:10001(8000) ack 1

// RTO
+.188 > . 1:1001(1000) ack 1

// The original data is acked and new data is sent(F-RTO step 2.b)
   +0 < . 1:1(0) ack 2001 win 257
   +0 > P. 10001:12001(2000) ack 1

// D-SACK caused by TLP is regarded as a dupack, this results in
// the incorrect judgment of "loss was real"(F-RTO step 3.a)
+.022 < . 1:1(0) ack 2001 win 257 <sack 1001:2001,nop,nop>

// Never-retransmitted data(3001:4001) are acked and
// expect to switch to open state(F-RTO step 3.b)
   +0 < . 1:1(0) ack 4001 win 257
+0 %{ assert tcpi_ca_state == 0, tcpi_ca_state }%

Fixes: e33099f96d99 ("tcp: implement RFC5682 F-RTO")
Signed-off-by: Pengcheng Yang <yangpc@wangsu.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Tested-by: Neal Cardwell <ncardwell@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/1650967419-2150-1-git-send-email-yangpc@wangsu.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

Revert "ibmvnic: Add ethtool private flag for driver-defined queue limits"

[ Upstream commit aeaf59b78712c7a1827c76f086acff4f586e072f ]

This reverts commit 723ad916134784b317b72f3f6cf0f7ba774e5dae

When client requests channel or ring size larger than what the server
can support the server will cap the request to the supported max. So,
the client would not be able to successfully request resources that
exceed the server limit.

Fixes: 723ad9161347 ("ibmvnic: Add ethtool private flag for driver-defined queue limits")
Signed-off-by: Dany Madden <drt@linux.ibm.com>
Link: https://lore.kernel.org/r/20220427235146.23189-1-drt@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ixgbe: ensure IPsec VF<->PF compatibility

[ Upstream commit f049efc7f7cd2f3c419f55040928eaefb13b3636 ]

The VF driver can forward any IPsec flags and such makes the function
is not extendable and prone to backward/forward incompatibility.

If new software runs on VF, it won't know that PF configured something
completely different as it "knows" only XFRM_OFFLOAD_INBOUND flag.

Fixes: eda0333ac293 ("ixgbe: add VF IPsec management")
Reviewed-by: Raed Salem <raeds@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Shannon Nelson <snelson@pensando.io>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20220427173152.443102-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

perf arm-spe: Fix addresses of synthesized SPE events

[ Upstream commit 4e13f6706d5aee1a6b835a44f6cf4971a921dcb8 ]

This patch corrects a bug whereby synthesized events from SPE
samples are missing virtual addresses.

Fixes: 54f7815efef7fad9 ("perf arm-spe: Fill address info for samples")
Reviewed-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Timothy Hayes <timothy.hayes@arm.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: bpf@vger.kernel.org
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: John Fastabend <john.fastabend@gmail.com>
Cc: John Garry <john.garry@huawei.com>
Cc: KP Singh <kpsingh@kernel.org>
Cc: Leo Yan <leo.yan@linaro.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Martin KaFai Lau <kafai@fb.com>
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: netdev@vger.kernel.org
Cc: Song Liu <songliubraving@fb.com>
Cc: Will Deacon <will@kernel.org>
Cc: Yonghong Song <yhs@fb.com>
Link: https://lore.kernel.org/r/20220421165205.117662-2-timothy.hayes@arm.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

gfs2: No short reads or writes upon glock contention

[ Upstream commit 296abc0d91d8b65d42224dd33452ace14491ad08 ]

Commit 00bfe02f4796 ("gfs2: Fix mmap + page fault deadlocks for buffered
I/O") changed gfs2_file_read_iter() and gfs2_file_buffered_write() to
allow dropping the inode glock while faulting in user buffers.  When the
lock was dropped, a short result was returned to indicate that the
operation was interrupted.

As pointed out by Linus (see the link below), this behavior is broken
and the operations should always re-acquire the inode glock and resume
the operation instead.

Link: https://lore.kernel.org/lkml/CAHk-=whaz-g_nOOoo8RRiWNjnv2R+h6_xk2F1J4TuSRxk1MtLw@mail.gmail.com/
Fixes: 00bfe02f4796 ("gfs2: Fix mmap + page fault deadlocks for buffered I/O")
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

gfs2: Make sure not to return short direct writes

[ Upstream commit 3bde4c48586074202044456285a97ccdf9048988 ]

When direct writes fail with -ENOTBLK because we're writing into a
hole (gfs2_iomap_begin()) or because of a page invalidation failure
(iomap_dio_rw()), we're falling back to buffered writes.  In that case,
when we lose the inode glock in gfs2_file_buffered_write(), we want to
re-acquire it instead of returning a short write.

Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

gfs2: Minor retry logic cleanup

[ Upstream commit 124c458a401a2497f796e4f2d6cafac6edbea8e9 ]

Clean up the retry logic in the read and write functions somewhat.

Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

gfs2: Prevent endless loops in gfs2_file_buffered_write

[ Upstream commit 554c577cee95bdc1d03d9f457e57dc96eb791845 ]

Currently, instead of performing a short write,
iomap_file_buffered_write will fail when part of its iov iterator cannot
be read.  In contrast, gfs2_file_buffered_write will loop around if it
can read part of the iov iterator, so we can end up in an endless loop.

This should be fixed in iomap_file_buffered_write (and also
generic_perform_write), but this comes a bit late in the 5.16
development cycle, so work around it in the filesystem by
trimming the iov iterator to the known-good size for now.

Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: fec: add missing of_node_put() in fec_enet_init_stop_mode()

[ Upstream commit d2b52ec056d5bddb055c8f21d7489a23548d0838 ]

Put device node in error path in fec_enet_init_stop_mode().

Fixes: 8a448bf832af ("net: ethernet: fec: move GPR register offset and bit into DT")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20220426125231.375688-1-yangyingliang@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

bnx2x: fix napi API usage sequence

[ Upstream commit af68656d66eda219b7f55ce8313a1da0312c79e1 ]

While handling PCI errors (AER flow) driver tries to
disable NAPI [napi_disable()] after NAPI is deleted
[__netif_napi_del()] which causes unexpected system
hang/crash.

System message log shows the following:
=======================================
[ 3222.537510] EEH: Detected PCI bus error on PHB#384-PE#800000 [ 3222.537511] EEH: This PCI device has failed 2 times in the last hour and will be permanently disabled after 5 failures.
[ 3222.537512] EEH: Notify device drivers to shutdown [ 3222.537513] EEH: Beginning: 'error_detected(IO frozen)'
[ 3222.537514] EEH: PE#800000 (PCI 0384:80:00.0): Invoking
bnx2x->error_detected(IO frozen)
[ 3222.537516] bnx2x: [bnx2x_io_error_detected:14236(eth14)]IO error detected [ 3222.537650] EEH: PE#800000 (PCI 0384:80:00.0): bnx2x driver reports:
'need reset'
[ 3222.537651] EEH: PE#800000 (PCI 0384:80:00.1): Invoking
bnx2x->error_detected(IO frozen)
[ 3222.537651] bnx2x: [bnx2x_io_error_detected:14236(eth13)]IO error detected [ 3222.537729] EEH: PE#800000 (PCI 0384:80:00.1): bnx2x driver reports:
'need reset'
[ 3222.537729] EEH: Finished:'error_detected(IO frozen)' with aggregate recovery state:'need reset'
[ 3222.537890] EEH: Collect temporary log [ 3222.583481] EEH: of node=0384:80:00.0 [ 3222.583519] EEH: PCI device/vendor: 168e14e4 [ 3222.583557] EEH: PCI cmd/status register: 00100140 [ 3222.583557] EEH: PCI-E capabilities and status follow:
[ 3222.583744] EEH: PCI-E 00: 00020010 012c8da2 00095d5e 00455c82 [ 3222.583892] EEH: PCI-E 10: 10820000 00000000 00000000 00000000 [ 3222.583893] EEH: PCI-E 20: 00000000 [ 3222.583893] EEH: PCI-E AER capability register set follows:
[ 3222.584079] EEH: PCI-E AER 00: 13c10001 00000000 00000000 00062030 [ 3222.584230] EEH: PCI-E AER 10: 00002000 000031c0 000001e0 00000000 [ 3222.584378] EEH: PCI-E AER 20: 00000000 00000000 00000000 00000000 [ 3222.584416] EEH: PCI-E AER 30: 00000000 00000000 [ 3222.584416] EEH: of node=0384:80:00.1 [ 3222.584454] EEH: PCI device/vendor: 168e14e4 [ 3222.584491] EEH: PCI cmd/status register: 00100140 [ 3222.584492] EEH: PCI-E capabilities and status follow:
[ 3222.584677] EEH: PCI-E 00: 00020010 012c8da2 00095d5e 00455c82 [ 3222.584825] EEH: PCI-E 10: 10820000 00000000 00000000 00000000 [ 3222.584826] EEH: PCI-E 20: 00000000 [ 3222.584826] EEH: PCI-E AER capability register set follows:
[ 3222.585011] EEH: PCI-E AER 00: 13c10001 00000000 00000000 00062030 [ 3222.585160] EEH: PCI-E AER 10: 00002000 000031c0 000001e0 00000000 [ 3222.585309] EEH: PCI-E AER 20: 00000000 00000000 00000000 00000000 [ 3222.585347] EEH: PCI-E AER 30: 00000000 00000000 [ 3222.586872] RTAS: event: 5, Type: Platform Error (224), Severity: 2 [ 3222.586873] EEH: Reset without hotplug activity [ 3224.762767] EEH: Beginning: 'slot_reset'
[ 3224.762770] EEH: PE#800000 (PCI 0384:80:00.0): Invoking
bnx2x->slot_reset()
[ 3224.762771] bnx2x: [bnx2x_io_slot_reset:14271(eth14)]IO slot reset initializing...
[ 3224.762887] bnx2x 0384:80:00.0: enabling device (0140 -> 0142) [ 3224.768157] bnx2x: [bnx2x_io_slot_reset:14287(eth14)]IO slot reset
--> driver unload

Uninterruptible tasks
=====================
crash> ps | grep UN
     213      2  11  c000000004c89e00  UN   0.0       0      0  [eehd]
     215      2   0  c000000004c80000  UN   0.0       0      0
[kworker/0:2]
    2196      1  28  c000000004504f00  UN   0.1   15936  11136  wickedd
    4287      1   9  c00000020d076800  UN   0.0    4032   3008  agetty
    4289      1  20  c00000020d056680  UN   0.0    7232   3840  agetty
   32423      2  26  c00000020038c580  UN   0.0       0      0
[kworker/26:3]
   32871   4241  27  c0000002609ddd00  UN   0.1   18624  11648  sshd
   32920  10130  16  c00000027284a100  UN   0.1   48512  12608  sendmail
   33092  32987   0  c000000205218b00  UN   0.1   48512  12608  sendmail
   33154   4567  16  c000000260e51780  UN   0.1   48832  12864  pickup
   33209   4241  36  c000000270cb6500  UN   0.1   18624  11712  sshd
   33473  33283   0  c000000205211480  UN   0.1   48512  12672  sendmail
   33531   4241  37  c00000023c902780  UN   0.1   18624  11648  sshd

EEH handler hung while bnx2x sleeping and holding RTNL lock
===========================================================
crash> bt 213
PID: 213    TASK: c000000004c89e00  CPU: 11  COMMAND: "eehd"
  #0 [c000000004d477e0] __schedule at c000000000c70808
  #1 [c000000004d478b0] schedule at c000000000c70ee0
  #2 [c000000004d478e0] schedule_timeout at c000000000c76dec
  #3 [c000000004d479c0] msleep at c0000000002120cc
  #4 [c000000004d479f0] napi_disable at c000000000a06448
                                        ^^^^^^^^^^^^^^^^
  #5 [c000000004d47a30] bnx2x_netif_stop at c0080000018dba94 [bnx2x]
  #6 [c000000004d47a60] bnx2x_io_slot_reset at c0080000018a551c [bnx2x]
  #7 [c000000004d47b20] eeh_report_reset at c00000000004c9bc
  #8 [c000000004d47b90] eeh_pe_report at c00000000004d1a8
  #9 [c000000004d47c40] eeh_handle_normal_event at c00000000004da64

And the sleeping source code
============================
crash> dis -ls c000000000a06448
FILE: ../net/core/dev.c
LINE: 6702

   6697  {
   6698          might_sleep();
   6699          set_bit(NAPI_STATE_DISABLE, &n->state);
   6700
   6701          while (test_and_set_bit(NAPI_STATE_SCHED, &n->state))
* 6702                  msleep(1);
   6703          while (test_and_set_bit(NAPI_STATE_NPSVC, &n->state))
   6704                  msleep(1);
   6705
   6706          hrtimer_cancel(&n->timer);
   6707
   6708          clear_bit(NAPI_STATE_DISABLE, &n->state);
   6709  }

EEH calls into bnx2x twice based on the system log above, first through
bnx2x_io_error_detected() and then bnx2x_io_slot_reset(), and executes
the following call chains:

bnx2x_io_error_detected()
  +-> bnx2x_eeh_nic_unload()
       +-> bnx2x_del_all_napi()
            +-> __netif_napi_del()

bnx2x_io_slot_reset()
  +-> bnx2x_netif_stop()
       +-> bnx2x_napi_disable()
            +->napi_disable()

Fix this by correcting the sequence of NAPI APIs usage,
that is delete the NAPI after disabling it.

Fixes: 7fa6f34081f1 ("bnx2x: AER revised")
Reported-by: David Christensen <drc@linux.vnet.ibm.com>
Tested-by: David Christensen <drc@linux.vnet.ibm.com>
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Link: https://lore.kernel.org/r/20220426153913.6966-1-manishc@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

tls: Skip tls_append_frag on zero copy size

[ Upstream commit a0df71948e9548de819a6f1da68f5f1742258a52 ]

Calling tls_append_frag when max_open_record_len == record->len might
add an empty fragment to the TLS record if the call happens to be on the
page boundary. Normally tls_append_frag coalesces the zero-sized
fragment to the previous one, but not if it's on page boundary.

If a resync happens then, the mlx5 driver posts dump WQEs in
tx_post_resync_dump, and the empty fragment may become a data segment
with byte_count == 0, which will confuse the NIC and lead to a CQE
error.

This commit fixes the described issue by skipping tls_append_frag on
zero size to avoid adding empty fragments. The fix is not in the driver,
because an empty fragment is hardly the desired behavior.

Fixes: e8f69799810c ("net/tls: Add generic NIC offload infrastructure")
Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://lore.kernel.org/r/20220426154949.159055-1-maximmi@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/amd/display: Fix memory leak in dcn21_clock_source_create

[ Upstream commit 65e54987508b6f0771f56bdfa3ee1926d52785ae ]

When dcn20_clk_src_construct() fails, we need to release clk_src.

Fixes: 6f4e6361c3ff ("drm/amd/display: Add Renoir resource (v2)")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/amdkfd: Fix GWS queue count

[ Upstream commit 7c6b6e18c890f30965b0589b0a57645e1dbccfde ]

dqm->gws_queue_count and pdd->qpd.mapped_gws_queue need to be updated
each time the queue gets evicted.

Fixes: b8020b0304c8 ("drm/amdkfd: Enable over-subscription with >1 GWS queue")
Signed-off-by: David Yat Sin <david.yatsin@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

netfilter: conntrack: fix udp offload timeout sysctl

[ Upstream commit 626873c446f7559d5af8b48cefad903ffd85cf4e ]

`nf_flowtable_udp_timeout` sysctl option is available only
if CONFIG_NFT_FLOW_OFFLOAD enabled. But infra for this flow
offload UDP timeout was added under CONFIG_NF_FLOW_TABLE
config option. So, if you have CONFIG_NFT_FLOW_OFFLOAD
disabled and CONFIG_NF_FLOW_TABLE enabled, the
`nf_flowtable_udp_timeout` is not present in sysfs.
Please note, that TCP flow offload timeout sysctl option
is present even CONFIG_NFT_FLOW_OFFLOAD is disabled.

I suppose it was a typo in commit that adds UDP flow offload
timeout and CONFIG_NF_FLOW_TABLE should be used instead.

Fixes: 975c57504da1 ("netfilter: conntrack: Introduce udp offload timeout configuration")
Signed-off-by: Volodymyr Mytnyk <volodymyr.mytnyk@plvision.eu>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

io_uring: check reserved fields for recv/recvmsg

[ Upstream commit 5a1e99b61b0c81388cde0c808b3e4173907df19f ]

We should check unused fields for non-zero and -EINVAL if they are set,
making it consistent with other opcodes.

Fixes: aa1fa28fc73e ("io_uring: add support for recvmsg()")
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>

io_uring: check reserved fields for send/sendmsg

[ Upstream commit 588faa1ea5eecb351100ee5d187b9be99210f70d ]

We should check unused fields for non-zero and -EINVAL if they are set,
making it consistent with other opcodes.

Fixes: 0fa03c624d8f ("io_uring: add support for sendmsg()")
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: dsa: lantiq_gswip: Don't set GSWIP_MII_CFG_RMII_CLK

[ Upstream commit 71cffebf6358a7f5031f5b208bbdc1cb4db6e539 ]

Commit 4b5923249b8fa4 ("net: dsa: lantiq_gswip: Configure all remaining
GSWIP_MII_CFG bits") added all known bits in the GSWIP_MII_CFGp
register. It helped bring this register into a well-defined state so the
driver has to rely less on the bootloader to do things right.
Unfortunately it also sets the GSWIP_MII_CFG_RMII_CLK bit without any
possibility to configure it. Upon further testing it turns out that all
boards which are supported by the GSWIP driver in OpenWrt which use an
RMII PHY have a dedicated oscillator on the board which provides the
50MHz RMII reference clock.

Don't set the GSWIP_MII_CFG_RMII_CLK bit (but keep the code which always
clears it) to fix support for the Fritz!Box 7362 SL in OpenWrt. This is
a board with two Atheros AR8030 RMII PHYs. With the "RMII clock" bit set
the MAC also generates the RMII reference clock whose signal then
conflicts with the signal from the oscillator on the board. This results
in a constant cycle of the PHY detecting link up/down (and as a result
of that: the two ports using the AR8030 PHYs are not working).

At the time of writing this patch there's no known board where the MAC
(GSWIP) has to generate the RMII reference clock. If needed this can be
implemented in future by providing a device-tree flag so the
GSWIP_MII_CFG_RMII_CLK bit can be toggled per port.

Fixes: 4b5923249b8fa4 ("net: dsa: lantiq_gswip: Configure all remaining GSWIP_MII_CFG bits")
Tested-by: Jan Hoffmann <jan@3e8.eu>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Link: https://lore.kernel.org/r/20220425152027.2220750-1-martin.blumenstingl@googlemail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/sun4i: Remove obsolete references to PHYS_OFFSET

[ Upstream commit dc3ae06c5f2170d879ff58696f629d8c3868aec3 ]

commit b4bdc4fbf8d0 ("soc: sunxi: Deal with the MBUS DMA offsets in a
central place") added a platform device notifier that sets the DMA
offset for all of the display engine frontend and backend devices.

The code applying the offset to DMA buffer physical addresses was then
removed from the backend driver in commit 756668ba682e ("drm/sun4i:
backend: Remove the MBUS quirks"), but the code subtracting PHYS_OFFSET
was left in the frontend driver.

As a result, the offset was applied twice in the frontend driver. This
likely went unnoticed because it only affects specific configurations
(scaling or certain pixel formats) where the frontend is used, on boards
with both one of these older SoCs and more than 1 GB of DRAM.

In addition, the references to PHYS_OFFSET prevent compiling the driver
on architectures where PHYS_OFFSET is not defined.

Fixes: b4bdc4fbf8d0 ("soc: sunxi: Deal with the MBUS DMA offsets in a central place")
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220424162633.12369-4-samuel@sholland.org
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: dsa: mv88e6xxx: Fix port_hidden_wait to account for port_base_addr

[ Upstream commit 24cbdb910bb62b5be3865275e5682be1a7708c0f ]

The other port_hidden functions rely on the port_read/port_write
functions to access the hidden control port. These functions apply the
offset for port_base_addr where applicable. Update port_hidden_wait to
use the port_wait_bit so that port_base_addr offsets are accounted for
when waiting for the busy bit to change.

Without the offset the port_hidden_wait function would timeout on
devices that have a non-zero port_base_addr (e.g. MV88E6141), however
devices that have a zero port_base_addr would operate correctly (e.g.
MV88E6390).

Fixes: 609070133aff ("net: dsa: mv88e6xxx: update code operating on hidden registers")
Signed-off-by: Nathan Rossi <nathan@nathanrossi.com>
Reviewed-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220425070454.348584-1-nathan@nathanrossi.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: phy: marvell10g: fix return value on error

[ Upstream commit 0ed9704b660b259b54743cad8a84a11148f60f0a ]

Return back the error value that we get from phy_read_mmd().

Fixes: c84786fa8f91 ("net: phy: marvell10g: read copper results from CSSR1")
Signed-off-by: Baruch Siach <baruch.siach@siklu.com>
Reviewed-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/f47cb031aeae873bb008ba35001607304a171a20.1650868058.git.baruch@tkos.co.il
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: bcmgenet: hide status block before TX timestamping

[ Upstream commit acac0541d1d65e81e599ec399d34d184d2424401 ]

The hardware checksum offloading requires use of a transmit
status block inserted before the outgoing frame data, this was
updated in '9a9ba2a4aaaa ("net: bcmgenet: always enable status blocks")'

However, skb_tx_timestamp() assumes that it is passed a raw frame
and PTP parsing chokes on this status block.

Fix this by calling __skb_pull(), which hides the TSB before calling
skb_tx_timestamp(), so an outgoing PTP packet is parsed correctly.

As the data in the skb has already been set up for DMA, and the
dma_unmap_* calls use a separately stored address, there is no
no effective change in the data transmission.

Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220424165307.591145-1-jonathan.lemon@gmail.com
Fixes: d03825fba459 ("net: bcmgenet: add skb_tx_timestamp call")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

cpufreq: qcom-cpufreq-hw: Clear dcvs interrupts

[ Upstream commit e4e6448638a01905faeda9bf96aa9df7c8ef463c ]

It's noted that dcvs interrupts are not self-clearing, thus an interrupt
handler runs constantly, which leads to a severe regression in runtime.
To fix the problem an explicit write to clear interrupt register is
required, note that on OSM platforms the register may not be present.

Fixes: 275157b367f4 ("cpufreq: qcom-cpufreq-hw: Add dcvs interrupt support")
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

clk: sunxi: sun9i-mmc: check return value after calling platform_get_resource()

[ Upstream commit f58ca215cda1975f77b2b762903684a3c101bec9 ]

It will cause null-ptr-deref if platform_get_resource() returns NULL,
we need check the return value.

Fixes: 7a6fca879f59 ("clk: sunxi: Add driver for A80 MMC config clocks/resets")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20220421134308.2885094-1-yangyingliang@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

bus: sunxi-rsb: Fix the return value of sunxi_rsb_device_create()

[ Upstream commit fff8c10368e64e7f8960f149375c12ca5f3b30af ]

This code is really spurious.
It always returns an ERR_PTR, even when err is known to be 0 and calls
put_device() after a successful device_register() call.

It is likely that the return statement in the normal path is missing.
Add 'return rdev;' to fix it.

Fixes: d787dcdb9c8f ("bus: sunxi-rsb: Add driver for Allwinner Reduced Serial Bus")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Tested-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/ef2b9576350bba4c8e05e669e9535e9e2a415763.1650551719.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Sasha Levin <sashal@kernel.org>

tcp: make sure treq->af_specific is initialized

[ Upstream commit ba5a4fdd63ae0c575707030db0b634b160baddd7 ]

syzbot complained about a recent change in TCP stack,
hitting a NULL pointer [1]

tcp request sockets have an af_specific pointer, which
was used before the blamed change only for SYNACK generation
in non SYNCOOKIE mode.

tcp requests sockets momentarily created when third packet
coming from client in SYNCOOKIE mode were not using
treq->af_specific.

Make sure this field is populated, in the same way normal
TCP requests sockets do in tcp_conn_request().

[1]
TCP: request_sock_TCPv6: Possible SYN flooding on port 20002. Sending cookies.  Check SNMP counters.
general protection fault, probably for non-canonical address 0xdffffc0000000001: 0000 [#1] PREEMPT SMP KASAN
KASAN: null-ptr-deref in range [0x0000000000000008-0x000000000000000f]
CPU: 1 PID: 3695 Comm: syz-executor864 Not tainted 5.18.0-rc3-syzkaller-00224-g5fd1fe4807f9 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
RIP: 0010:tcp_create_openreq_child+0xe16/0x16b0 net/ipv4/tcp_minisocks.c:534
Code: 48 c1 ea 03 80 3c 02 00 0f 85 e5 07 00 00 4c 8b b3 28 01 00 00 48 b8 00 00 00 00 00 fc ff df 49 8d 7e 08 48 89 fa 48 c1 ea 03 <80> 3c 02 00 0f 85 c9 07 00 00 48 8b 3c 24 48 89 de 41 ff 56 08 48
RSP: 0018:ffffc90000de0588 EFLAGS: 00010202
RAX: dffffc0000000000 RBX: ffff888076490330 RCX: 0000000000000100
RDX: 0000000000000001 RSI: ffffffff87d67ff0 RDI: 0000000000000008
RBP: ffff88806ee1c7f8 R08: 0000000000000000 R09: 0000000000000000
R10: ffffffff87d67f00 R11: 0000000000000000 R12: ffff88806ee1bfc0
R13: ffff88801b0e0368 R14: 0000000000000000 R15: 0000000000000000
FS:  00007f517fe58700(0000) GS:ffff8880b9d00000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007ffcead76960 CR3: 000000006f97b000 CR4: 00000000003506e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
 <IRQ>
 tcp_v6_syn_recv_sock+0x199/0x23b0 net/ipv6/tcp_ipv6.c:1267
 tcp_get_cookie_sock+0xc9/0x850 net/ipv4/syncookies.c:207
 cookie_v6_check+0x15c3/0x2340 net/ipv6/syncookies.c:258
 tcp_v6_cookie_check net/ipv6/tcp_ipv6.c:1131 [inline]
 tcp_v6_do_rcv+0x1148/0x13b0 net/ipv6/tcp_ipv6.c:1486
 tcp_v6_rcv+0x3305/0x3840 net/ipv6/tcp_ipv6.c:1725
 ip6_protocol_deliver_rcu+0x2e9/0x1900 net/ipv6/ip6_input.c:422
 ip6_input_finish+0x14c/0x2c0 net/ipv6/ip6_input.c:464
 NF_HOOK include/linux/netfilter.h:307 [inline]
 NF_HOOK include/linux/netfilter.h:301 [inline]
 ip6_input+0x9c/0xd0 net/ipv6/ip6_input.c:473
 dst_input include/net/dst.h:461 [inline]
 ip6_rcv_finish net/ipv6/ip6_input.c:76 [inline]
 NF_HOOK include/linux/netfilter.h:307 [inline]
 NF_HOOK include/linux/netfilter.h:301 [inline]
 ipv6_rcv+0x27f/0x3b0 net/ipv6/ip6_input.c:297
 __netif_receive_skb_one_core+0x114/0x180 net/core/dev.c:5405
 __netif_receive_skb+0x24/0x1b0 net/core/dev.c:5519
 process_backlog+0x3a0/0x7c0 net/core/dev.c:5847
 __napi_poll+0xb3/0x6e0 net/core/dev.c:6413
 napi_poll net/core/dev.c:6480 [inline]
 net_rx_action+0x8ec/0xc60 net/core/dev.c:6567
 __do_softirq+0x29b/0x9c2 kernel/softirq.c:558
 invoke_softirq kernel/softirq.c:432 [inline]
 __irq_exit_rcu+0x123/0x180 kernel/softirq.c:637
 irq_exit_rcu+0x5/0x20 kernel/softirq.c:649
 sysvec_apic_timer_interrupt+0x93/0xc0 arch/x86/kernel/apic/apic.c:1097

Fixes: 5b0b9e4c2c89 ("tcp: md5: incorrect tcp_header_len for incoming connections")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Francesco Ruggeri <fruggeri@arista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

tcp: fix potential xmit stalls caused by TCP_NOTSENT_LOWAT

[ Upstream commit 4bfe744ff1644fbc0a991a2677dc874475dd6776 ]

I had this bug sitting for too long in my pile, it is time to fix it.

Thanks to Doug Porter for reminding me of it!

We had various attempts in the past, including commit
0cbe6a8f089e ("tcp: remove SOCK_QUEUE_SHRUNK"),
but the issue is that TCP stack currently only generates
EPOLLOUT from input path, when tp->snd_una has advanced
and skb(s) cleaned from rtx queue.

If a flow has a big RTT, and/or receives SACKs, it is possible
that the notsent part (tp->write_seq - tp->snd_nxt) reaches 0
and no more data can be sent until tp->snd_una finally advances.

What is needed is to also check if POLLOUT needs to be generated
whenever tp->snd_nxt is advanced, from output path.

This bug triggers more often after an idle period, as
we do not receive ACK for at least one RTT. tcp_notsent_lowat
could be a fraction of what CWND and pacing rate would allow to
send during this RTT.

In a followup patch, I will remove the bogus call
to tcp_chrono_stop(sk, TCP_CHRONO_SNDBUF_LIMITED)
from tcp_check_space(). Fact that we have decided to generate
an EPOLLOUT does not mean the application has immediately
refilled the transmit queue. This optimistic call
might have been the reason the bug seemed not too serious.

Tested:

200 ms rtt, 1% packet loss, 32 MB tcp_rmem[2] and tcp_wmem[2]

$ echo 500000 >/proc/sys/net/ipv4/tcp_notsent_lowat
$ cat bench_rr.sh
SUM=0
for i in {1..10}
do
 V=`netperf -H remote_host -l30 -t TCP_RR -- -r 10000000,10000 -o LOCAL_BYTES_SENT | egrep -v "MIGRATED|Bytes"`
 echo $V
 SUM=$(($SUM + $V))
done
echo SUM=$SUM

Before patch:
$ bench_rr.sh
130000000
80000000
140000000
140000000
140000000
140000000
130000000
40000000
90000000
110000000
SUM=1140000000

After patch:
$ bench_rr.sh
430000000
590000000
530000000
450000000
450000000
350000000
450000000
490000000
480000000
460000000
SUM=4680000000  # This is 410 % of the value before patch.

Fixes: c9bee3b7fdec ("tcp: TCP_NOTSENT_LOWAT socket option")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Doug Porter <dsp@fb.com>
Cc: Soheil Hassas Yeganeh <soheil@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ip_gre, ip6_gre: Fix race condition on o_seqno in collect_md mode

[ Upstream commit 31c417c948d7f6909cb63f0ac3298f3c38f8ce20 ]

As pointed out by Jakub Kicinski, currently using TUNNEL_SEQ in
collect_md mode is racy for [IP6]GRE[TAP] devices.  Consider the
following sequence of events:

1. An [IP6]GRE[TAP] device is created in collect_md mode using "ip link
   add ... external".  "ip" ignores "[o]seq" if "external" is specified,
   so TUNNEL_SEQ is off, and the device is marked as NETIF_F_LLTX (i.e.
   it uses lockless TX);
2. Someone sets TUNNEL_SEQ on outgoing skb's, using e.g.
   bpf_skb_set_tunnel_key() in an eBPF program attached to this device;
3. gre_fb_xmit() or __gre6_xmit() processes these skb's:

gre_build_header(skb, tun_hlen,
 flags, protocol,
 tunnel_id_to_key32(tun_info->key.tun_id),
 (flags & TUNNEL_SEQ) ? htonl(tunnel->o_seqno++)
      : 0);   ^^^^^^^^^^^^^^^^^

Since we are not using the TX lock (&txq->_xmit_lock), multiple CPUs may
try to do this tunnel->o_seqno++ in parallel, which is racy.  Fix it by
making o_seqno atomic_t.

As mentioned by Eric Dumazet in commit b790e01aee74 ("ip_gre: lockless
xmit"), making o_seqno atomic_t increases "chance for packets being out
of order at receiver" when NETIF_F_LLTX is on.

Maybe a better fix would be:

1. Do not ignore "oseq" in external mode.  Users MUST specify "oseq" if
   they want the kernel to allow sequencing of outgoing packets;
2. Reject all outgoing TUNNEL_SEQ packets if the device was not created
   with "oseq".

Unfortunately, that would break userspace.

We could now make [IP6]GRE[TAP] devices always NETIF_F_LLTX, but let us
do it in separate patches to keep this fix minimal.

Suggested-by: Jakub Kicinski <kuba@kernel.org>
Fixes: 77a5196a804e ("gre: add sequence number for collect md mode.")
Signed-off-by: Peilin Ye <peilin.ye@bytedance.com>
Acked-by: William Tu <u9012063@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ip6_gre: Make o_seqno start from 0 in native mode

[ Upstream commit fde98ae91f79cab4e020f40c35ed23cbdc59661c ]

For IP6GRE and IP6GRETAP devices, currently o_seqno starts from 1 in
native mode.  According to RFC 2890 2.2., "The first datagram is sent
with a sequence number of 0."  Fix it.

It is worth mentioning that o_seqno already starts from 0 in collect_md
mode, see the "if (tunnel->parms.collect_md)" clause in __gre6_xmit(),
where tunnel->o_seqno is passed to gre_build_header() before getting
incremented.

Fixes: c12b395a4664 ("gre: Support GRE over IPv6")
Signed-off-by: Peilin Ye <peilin.ye@bytedance.com>
Acked-by: William Tu <u9012063@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>