Bin Meng [Fri, 4 Jun 2021 23:00:30 +0000 (07:00 +0800)]
riscv: ae350: doc: Remove CONFIG_SKIP_LOWLEVEL_INIT
The doc says CONFIG_SKIP_LOWLEVEL_INIT is in ax25-ae350.h, while
actually it is not. Remove it.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Bin Meng [Fri, 4 Jun 2021 05:51:13 +0000 (13:51 +0800)]
riscv: ae350: dts: Add missing "u-boot, dm-spl" for SPL config
At present the AE350 SPL defconfig is using OF_PRIOR_STAGE. The
intention was to use gdb to load device tree before running U-Boot
SPL/proper from RAM. When we switch to OF_SEPARATE we will have to
use our own DT but without "u-boot,dm-spl" in several essential
nodes, SPL does not boot.
Let's add all the required "u-boot,dm-spl" for SPL config.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Bin Meng [Fri, 4 Jun 2021 05:51:12 +0000 (13:51 +0800)]
riscv: ae350: dts: Fix #interrupt-cells for plic0 in 32-bit
All the device nodes that refer to plic0 as their interrupt parent
have 2 cells encoded in their interrupts property, but plic0 only
provides 1 cell in #interrupt-cells which is incorrect.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Bin Meng [Fri, 4 Jun 2021 05:51:11 +0000 (13:51 +0800)]
riscv: ae350: dts: Remove the unnecessary #address-cells in plic nodes
PLIC nodes don't have child nodes, so #address-cells is not needed.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Bin Meng [Fri, 4 Jun 2021 05:51:10 +0000 (13:51 +0800)]
riscv: ae350: dts: Remove the unnecessary space in bootargs
There are two spaces before "debug' in bootargs. Drop one.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Bin Meng [Fri, 4 Jun 2021 05:51:09 +0000 (13:51 +0800)]
riscv: ae350: dts: Add SPDX license header
The SPDX license header is currently missing. Add one.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Tom Rini [Tue, 15 Jun 2021 12:23:04 +0000 (08:23 -0400)]
Merge https://source.denx.de/u-boot/custodians/u-boot-marvell
- Turris: Fix bootcmd_rescue (Pali)
Pali Rohár [Mon, 14 Jun 2021 14:45:58 +0000 (16:45 +0200)]
arm: mvebu: turris_{omnia, mox}: ensure running bootcmd_rescue always works
One of the points of putting the rescue boot command into default
environment is that user can invoke it without physical access to the
board (without having to press the factory reset button), by running
run bootcmd_rescue
in U-Boot's console.
Therefore we have to ensure that bootcmd_rescue is always set to default
value, regardless of whether the factory reset button was pressed.
Otherwise the variable will be empty for example after upgrade from
previous U-Boot.
Fixes:
ec3784d62646 ("arm: mvebu: turris_mox: add support for board rescue mode")
Fixes:
176c3e7760a2 ("arm: mvebu: turris_omnia: support invoking rescue boot from console")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Tom Rini [Fri, 11 Jun 2021 12:29:34 +0000 (08:29 -0400)]
Merge tag 'xilinx-for-v2021.07-rc5' of https://source.denx.de/u-boot/custodians/u-boot-microblaze
Xilinx changes for v2021.07-rc5
zynqmp:
- Fix ANALOG_BUS value after powerup
- Disable EFI_CAPSULE_ON_DISK_EARLY
zynqmp-gqspi:
- Fix write issue
Michal Simek [Thu, 10 Jun 2021 12:33:55 +0000 (14:33 +0200)]
arm64: zynqmp: Disable EFI_CAPSULE_ON_DISK_EARLY
Sata/scsi and usb based devices are not started at this stage that's why
disks are not found and early update can't happen.
It is because of deficiency in the UEFI implementation which is not able to
deal with block devices which are added or removed after initialization.
EFI capsule on disk early feature needs to be fixed first to be able to
enable this feature properly.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Ashok Reddy Soma [Tue, 25 May 2021 12:36:27 +0000 (06:36 -0600)]
spi: zynqmp_gqspi: Fix write issue
Enable manual start in zynqmp_qspi_fill_gen_fifo().
Also enable GQSPI_IXR_GFNFULL_MASK and check for it instead of
GQSPI_IXR_GFEMTY_MASK.
Add dummy write to genfifo register in chipselect.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Adrian Fiergolski [Tue, 8 Jun 2021 10:37:23 +0000 (12:37 +0200)]
arm64: zynqmp: Writing correct value to ANALOG_BUS
The default register configuration after powerup for PSSYSMON_ANALOG_BUS
register is incorrect. Hence, fix this in SPL by writing correct fixed
value. It follows UG1085 chapter 'PS SYSMON Analog_Bus' and reflects commit
sw_apps:zynq ("
056ca65d44549ce27f716d423e8dfdefeee7440c")
in Xilinx:embeddedsw[1].
[1] https://github.com/Xilinx/embeddedsw
Signed-off-by: Adrian Fiergolski <adrian.fiergolski@fastree3d.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Tom Rini [Thu, 10 Jun 2021 17:27:14 +0000 (13:27 -0400)]
Merge https://source.denx.de/u-boot/custodians/u-boot-marvell
- mvebu: Turris MOX misc updates (cmds, rescue mode, LED's etc)
(Marek)
- mvebu: correct Armada 8K addresses (Heinrich)
Heinrich Schuchardt [Tue, 8 Jun 2021 10:00:35 +0000 (12:00 +0200)]
arm64: mvebu: correct Armada 8K addresses
0x04000000- 0x06000000 is reserved memory. We cannot load to anything here.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
Marek Behún [Mon, 7 Jun 2021 14:34:51 +0000 (16:34 +0200)]
arm: mvebu: turris_mox: enable options for Turris network boot
Enable configuration options to support Turris network boot. This
includes FIT support and some crypto commands.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Marek Behún [Mon, 7 Jun 2021 14:34:50 +0000 (16:34 +0200)]
arm: mvebu: dts: turris_mox: add nodes for SPI NOR partitions
Add nodes for SPI NOR partitions to the device tree of Turris MOX, as
are in Linux' device tree.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Marek Behún [Mon, 7 Jun 2021 14:34:49 +0000 (16:34 +0200)]
arm: mvebu: configs: turris_mox: add fdtfile default env variable
Add default fdtfile environment variable with value
marvell/armada-3720-turris-mox.dtb.
This can be useful for some boot scenarios.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Marek Behún [Mon, 7 Jun 2021 14:34:48 +0000 (16:34 +0200)]
arm: mvebu: turris_mox: start blinking PHY LEDs when entering rescue
Configure blinking on ethernet PHY LEDs on the MOX A board when entering
rescue mode via reset button.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Marek Behún [Mon, 7 Jun 2021 14:34:47 +0000 (16:34 +0200)]
arm: mvebu: turris_mox: add support for board rescue mode
Add necessary config options and board code to support board factory
reset / rescue mode on Turris MOX.
In order to also support invoking rescue mode from U-Boot console,
without having to press the factory reset button, put the rescue command
into `bootcmd_rescue` default environment variable. When factory reset
button is pressed, invoke rescue mode via distroboot by setting
`boot_targets` to `rescue`.
Rescue boot from console can be invoked by running
run bootcmd_rescue
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Marek Behún [Mon, 7 Jun 2021 14:34:46 +0000 (16:34 +0200)]
arm: mvebu: dts: turris_mox: add button and LED nodes
Add nodes for indicator LED and reset button so that board code can
implement board factory reset mechanism.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Joao Marcos Costa [Mon, 17 May 2021 21:20:38 +0000 (18:20 -0300)]
fs/squashfs: fix reading of fragmented files
The fragmented files were not correctly read because of two issues:
- The squashfs_file_info struct has a field named 'comp', which tells if
the file's fragment is compressed or not. This field was always set to
'true' in sqfs_get_regfile_info and sqfs_get_lregfile_info. It should
actually take sqfs_frag_lookup's return value. This patch addresses
these two assignments.
- In sqfs_read, the fragments (compressed or not) were copied to the
output buffer through a for loop which was reading data at the wrong
offset. Replace these loops by equivalent calls to memcpy, with the
right parameters.
I tested this patch by comparing the MD5 checksum of a few fragmented
files with the respective md5sum output in sandbox, considering both
compressed and uncompressed fragments.
Signed-off-by: Joao Marcos Costa <jmcosta944@gmail.com>
Tested-by: Richard Genoud <richard.genoud@posteo.net>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tom Rini [Wed, 9 Jun 2021 12:20:36 +0000 (08:20 -0400)]
Merge https://source.denx.de/u-boot/custodians/u-boot-usb
- dwc2 and cdns3 fixes
Tom Rini [Wed, 9 Jun 2021 12:20:24 +0000 (08:20 -0400)]
Merge tag 'efi-2021-07-rc5' of https://source.denx.de/u-boot/custodians/u-boot-efi
Pull request for efi-2021-07-rc5
Documentation:
* pinmux and ums man-page
Bug fixes:
* Consider that partition numbers as hexadecimal.
* Avoid a possible NULL dereference in efi_capsule_delete_file().
Heinrich Schuchardt [Tue, 8 Jun 2021 22:21:24 +0000 (00:21 +0200)]
efi_loader: fix Sphinx warning
Brackets '[' need to be escaped to avoid a build warning
lib/efi_loader/efi_image_loader.c:223:
WARNING: Inline strong start-string without end-string.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Masahisa Kojima <masahisa.kojima@linaro.org>
João Loureiro [Wed, 17 Mar 2021 15:52:21 +0000 (16:52 +0100)]
usb: dwc2: Avoid delay when initializing USB peripheral by dwc2
When `usb start` is called on the terminal, the dwc2 driver will try
to start every USB device as host first, even if it is explicitly
configured as peripheral in the device tree (dr_mode = "peripheral").
So to avoid an unwanted 15 seconds delay when initializing the usb
(one second per channel = 1s x 15), this patch adds a check to the
initialization, and will skip host initialization of the device is
explicitly set as peripheral. The checking is already done similarly
in the `drivers/usb/gadget/dwc2_udc_otg.c` driver.
Signed-off-by: João Loureiro <joaofl@gmail.com>
Heinrich Schuchardt [Wed, 2 Jun 2021 17:28:22 +0000 (19:28 +0200)]
efi_loader: efi_capsule_delete_file() NULL dereference
If opening a file fails, the file handle pointer is not valid and must not
be dereferenced.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Heinrich Schuchardt [Tue, 25 May 2021 16:00:13 +0000 (18:00 +0200)]
efi_loader: partition numbers are hexadecimal
If we want to address partition 15 of virtio block device 11, we have to
write:
virtio b:f
When calling sprintf() we must use %x for the device and partition numbers.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Patrick Delaunay [Fri, 4 Jun 2021 16:51:47 +0000 (18:51 +0200)]
doc: usage: man-page for ums command
Provide a man-page for the ums command - USB Mass Storage.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Patrick Delaunay [Fri, 4 Jun 2021 16:51:46 +0000 (18:51 +0200)]
cmd: Add dependency for ums command
Add the missing dependency for the command ums:
- CONFIG_BLK: call of blk_* functions in usb_mass_storage.c
- CONFIG_USB_GADGET: required to select CONFIG_USB_FUNCTION_MASS_STORAGE
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Patrick Delaunay [Wed, 2 Jun 2021 11:56:45 +0000 (13:56 +0200)]
doc: usage: man-page for pinmux command
Provide a man-page for the pinmux command.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Patrick Delaunay [Wed, 2 Jun 2021 08:11:19 +0000 (10:11 +0200)]
doc: usage: reorder commands in index.rst
Reorder alphabetically the command in the index of usage
in U-Boot documentation.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Tom Rini [Tue, 8 Jun 2021 21:46:49 +0000 (17:46 -0400)]
Merge https://source.denx.de/u-boot/custodians/u-boot-sh
- More pinctrl updates
Kishon Vijay Abraham I [Tue, 1 Jun 2021 10:56:16 +0000 (16:26 +0530)]
usb: cdns3: cdns3-ti: Fix clk_get_by_name() to get the correct name
Kernel device tree got updated to use clock name as "ref" instead of
"usb2_refclk". Fix cdns3-ti.c to use the correct name.
Fixes:
70e167495ab2 ("arm: dts: k3-j721e: Sync Linux v5.11-rc6 dts into U-Boot")
Fixes:
6239cc8c4e84 ("arm: dts: k3-j7200: Sync Linux v5.11-rc6 dts into U-Boot")
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Marek Vasut [Mon, 26 Apr 2021 20:04:11 +0000 (22:04 +0200)]
pinctrl: renesas: Synchronize R-Car Gen2/Gen3 tables with Linux 5.12
Synchronize R-Car Gen2/Gen3 pinctrl tables with Linux 5.12,
commit
9f4ad9e425a1 ("Linux 5.12") . This is a rather large
commit, since the macros in sh-pfc.h also got updated, so
all the PFC tables must be updated in lockstep.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Tom Rini [Mon, 7 Jun 2021 13:26:39 +0000 (09:26 -0400)]
Prepare v2021.07-rc4
Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Mon, 7 Jun 2021 12:09:35 +0000 (08:09 -0400)]
configs: Resync with savedefconfig
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Mon, 7 Jun 2021 11:22:14 +0000 (07:22 -0400)]
Merge tag 'u-boot-rockchip-
20210606' of https://source.denx.de/u-boot/custodians/u-boot-rockchip
Tom Rini [Sun, 6 Jun 2021 17:00:23 +0000 (13:00 -0400)]
Merge tag 'dm-pull-6jun21' of https://source.denx.de/u-boot/custodians/u-boot-dm
Minor fixes for sandbox and handling of dm-ranges
Tom Rini [Sat, 5 Jun 2021 15:17:55 +0000 (11:17 -0400)]
Merge tag 'video-for-2021-07-rc3' of https://source.denx.de/u-boot/custodians/u-boot-video
- disable legacy video for brxre1, mx28evk, pico-imx6ul,
pxm2 and rut boards after DM_VIDEO conversion deadline
Patrick Delaunay [Fri, 21 May 2021 10:25:00 +0000 (12:25 +0200)]
test: add dm_test_read_resource
Add a test of dev_read_resource with translation or without translation
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Patrick Delaunay [Fri, 21 May 2021 10:24:59 +0000 (12:24 +0200)]
net: luton: remove address translation after ofnode_read_resource
Removed call of ofnode_translate_address() after ofnode_read_resource
in luton_switch.c:luton_probe(); it is unnecessary since
the commit
feb7ac457c20 ("dm: core: Add address translation in
fdt_get_resource").
Fixes:
feb7ac457c20 ("dm: core: Add address translation in fdt_get_resource")
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reported-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Alper Nebi Yasak [Fri, 14 May 2021 13:48:40 +0000 (16:48 +0300)]
pwm: cros_ec: Rename "priv_auto_alloc_size" to "priv_auto"
With commit
41575d8e4c33 ("dm: treewide: Rename auto_alloc_size members
to be shorter") "priv_auto_alloc_size" was renamed to "priv_auto". This
driver was sent to the mailing list before that change, merged after it,
and still has the old form. Apply the rename here as well.
Fixes:
1b9ee2882e6b ("pwm: Add a driver for Chrome OS EC PWM")
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Heinrich Schuchardt [Sat, 15 May 2021 17:29:13 +0000 (19:29 +0200)]
sandbox: correct determination of the text base
os_find_text_base() assumes that first line of /proc/self/maps holds
information about the text. Hence we must call the function before calling
os_malloc() which calls mmap(0x10000000,).
Failure to do so has led to incorrect values for pc_reloc when an
exception was reported
=> exception undefined
Illegal instruction
pc = 0x5628d82e9d3c, pc_reloc = 0x5628c82e9d3c
as well as incorrect output of the bdinfo command
=> bdinfo
relocaddr = 0x0000000007858000
reloc off = 0x0000000010000000
Fixes:
b308d9fd18fa ("sandbox: Avoid using malloc() for system state")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Bin Meng [Fri, 30 Apr 2021 13:16:59 +0000 (21:16 +0800)]
of: addr: Remove call to dev_count_cells() in of_get_address()
In of_get_address(), there is:
dev_count_cells(dev, &na, &ns);
followed by:
bus->count_cells(dev, &na, &ns);
but no codes in between use na/ns, hence the first call is useless.
By dropping the first call, dev_count_cells() is now useless too.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Bin Meng [Fri, 30 Apr 2021 13:16:58 +0000 (21:16 +0800)]
of: addr: Translate 'dma-ranges' for parent nodes missing 'dma-ranges'
'dma-ranges' frequently exists without parent nodes having 'dma-ranges'.
While this is an error for 'ranges', this is fine because DMA capable
devices always have a translatable DMA address. Also, with no
'dma-ranges' at all, the assumption is that DMA addresses are 1:1 with
no restrictions unless perhaps the device itself has implicit
restrictions.
This keeps in sync with Linux kernel commit:
81db12ee15cb: of/address: Translate 'dma-ranges' for parent nodes missing 'dma-ranges'
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Anatolij Gustschin [Mon, 24 May 2021 15:31:26 +0000 (17:31 +0200)]
pico-imx6ul: disable video after DM_VIDEO conversion deadline
These boards were not converted to DM_VIDEO before deadline,
so disable video support for now.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Richard Hu <richard.hu@technexion.com>
Cc: Fabio Estevam <festevam@gmail.com>
Anatolij Gustschin [Mon, 24 May 2021 15:19:56 +0000 (17:19 +0200)]
brxre1: disable video after DM_VIDEO conversion deadline
The board was not converted to DM_VIDEO before deadline, so disable
video support for now.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
Anatolij Gustschin [Mon, 24 May 2021 14:45:29 +0000 (16:45 +0200)]
mx28evk: disable video after DM_VIDEO conversion deadline
The board was not converted to DM_VIDEO before deadline, so disable
video support for now.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Anatolij Gustschin [Mon, 24 May 2021 14:35:57 +0000 (16:35 +0200)]
siemens: pxm2: disable video after DM_VIDEO conversion deadline
The board was not converted to DM_VIDEO before deadline, so disable
video support for now.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Anatolij Gustschin [Mon, 24 May 2021 14:26:51 +0000 (16:26 +0200)]
siemens: rut: disable video after DM_VIDEO conversion deadline
The board was not converted to DM_VIDEO before deadline, so disable
video support for now.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Tom Rini [Fri, 4 Jun 2021 13:34:21 +0000 (09:34 -0400)]
Merge https://source.denx.de/u-boot/custodians/u-boot-marvell
- mvebu: a37xx: PCI related enhancements and fixes (Pali)
- mvebu: turris_omnia: Board specific updates, e.g. rescue
boot cmd etc (Marek)
Marek Behún [Fri, 28 May 2021 08:00:49 +0000 (10:00 +0200)]
arm: mvebu: turris_omnia: support invoking rescue boot from console
Make it possible to invoke rescue boot from U-Boot console, without
having to press the factory reset button. This is needed when accessing
the device remotely, for example.
Achieve this by putting rescue command into `bootcmd_rescue` default
environment variable and setting some distroboot environment variables
to their default values when the factory button is pressed.
Rescue boot from console can be invoked by running
run bootcmd_rescue
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Marek Behún [Fri, 28 May 2021 08:00:48 +0000 (10:00 +0200)]
arm: mvebu: turris_omnia: update rescue mode boot command
Update rescue mode boot command on Turris Omnia. We are compressing the
image with lzma now.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Pali Rohár [Wed, 26 May 2021 15:59:40 +0000 (17:59 +0200)]
arm: a37xx: pci: Fix configuring PCIe resources
The `ranges` DT property of the PCIe node is currently ignored by
Aardvark driver - all entries are used as transparent PCIe MEM, despite
some of them being defined for IO in DT.
This is because the driver does not setup PCIe outbound windows and thus
a default configuration is used.
This can cause an external abort on CPU when a device driver tries to
access non-MEM space.
Setup the PCIe windows according to the `ranges` property for all
non-MEM resources (currently only IO) and also non-transparent MEM
resources.
Because Linux expects that bootloader does not setup Aardvark PCIe
windows, disable them before booting Linux.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Pali Rohár [Wed, 26 May 2021 15:59:39 +0000 (17:59 +0200)]
arm: a37xx: pci: Increase PCIe MEM size from 16 MiB to 127 MiB
For some configurations with more PCIe cards and PCIe bridges, 16 MiB of
PCIe MEM space may not be enough. Since TF-A already allocates a 128 MiB
CPU window for PCIe, and since IO port space is only 64 KiB in total,
use all the remaining space (64 + 32 + 16 + 8 + 4 + 2 + 1 = 127 MiB) for
PCIe MEM.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Pali Rohár [Wed, 26 May 2021 15:59:38 +0000 (17:59 +0200)]
arm: a37xx: pci: Fix a3700_fdt_fix_pcie_regions() function
Current version of this function uses a lot of incorrect assumptions about
the `ranges` DT property:
* parent(#address-cells) == 2
* #size-cells == 2
* number of entries == 2
* address size of first entry == 0x1000000
* second child address entry == base + 0x1000000
Trying to increase PCIe MEM space to more than 16 MiB leads to an overlap
with PCIe IO space, and trying to define additional MEM space (as a third
entry in the `ranges` DT property) causes U-Boot to crash when booting the
kernel.
## Flattened Device Tree blob at
04f00000
Booting using the fdt blob at 0x4f00000
Loading Device Tree to
000000001fb01000, end
000000001fb08f12 ... OK
ERROR: board-specific fdt fixup failed: <unknown error>
- must RESET the board to recover.
Fix a3700_fdt_fix_pcie_regions() to properly parse and update all addresses
in the `ranges` property according to
https://elinux.org/Device_Tree_Usage#PCI_Address_Translation
Now it is possible to increase PCIe MEM space from 16 MiB to maximal value
of 127 MiB.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Fixes:
cb2ddb291ee6 ("arm64: mvebu: a37xx: add device-tree fixer for PCIe regions")
Reviewed-by: Stefan Roese <sr@denx.de>
Pali Rohár [Wed, 26 May 2021 15:59:37 +0000 (17:59 +0200)]
arm: a37xx: pci: Find PCIe controller node by compatible instead of path
Find PCIe DT node by compatible string instead of retrieving it by using
hardcoded DT path.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Pali Rohár [Wed, 26 May 2021 15:59:36 +0000 (17:59 +0200)]
arm: a37xx: pci: Fix DT compatible string to Linux' DT compatible
Change DT compatible string for A3700 PCIe from 'marvell,armada-37xx-pcie'
to 'marvell,armada-3700-pcie' to make U-Boot A3700 PCIe DT node compatible
with Linux' DT node.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Pali Rohár [Wed, 26 May 2021 15:59:35 +0000 (17:59 +0200)]
arm: a37xx: pci: Disable bus mastering when unloading driver
Disable Root Bridge I/O space, memory space and bus mastering in Aardvark's
remove method, which is called before booting Linux kernel.
This ensures that PCIe device which was initialized and used by U-Boot
cannot do new DMA transfers until Linux initializes PCI subsystem and loads
appropriate drivers for the device.
During initialization of PCI subsystem Linux in fact disables this bus
mastering on Root Bridge (and later enables it when driver is loaded and
configured), but there is a possibility of a small window after U-Boot
boots Linux when bus mastering is enabled, which is not correct.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Pali Rohár [Wed, 26 May 2021 15:59:34 +0000 (17:59 +0200)]
arm: a37xx: pci: Don't put link into LTSSM Recovery state during probe
During our debugging of the Aardvark driver in Linux we have discovered
that the PCIE_CORE_LINK_CTRL_STAT_REG register in fact controls standard
PCIe Link Control Register for PCIe Root Bridge. This led us to discover
that the name of the PCIE_CORE_LINK_TRAINING macro and the corresponding
comment by this macro's usage is misleading; this bit in fact controls
Retrain Link, which, according to PCIe base spec is defined as:
A write of 1b to this bit initiates Link retraining by directing the
Physical Layer LTSSM to the Recovery state. If the LTSSM is already in
Recovery or Configuration, re-entering Recovery is permitted but not
required.
Entering Recovery state is normally done from LTSSM L0, L0s and L1 states.
But since the pci-aardvark.c driver enables Link Training just a few lines
above, the controller is not in L0 ready state yet. So setting aardvark bit
PCIE_CORE_LINK_TRAINING does not actually enter Recovery state at this
place.
Moreover, trying to enter LTSSM Recovery state without other configuration
is causing issues for some cards (e.g. Atheros AR9xxx and QCA9xxx). Since
Recovery state is not entered, these issues are not triggered.
Remove code which tries to enter LTSSM Recovery state completely.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Sean Anderson [Thu, 27 May 2021 16:02:34 +0000 (12:02 -0400)]
fastboot: Fix overflow when calculating chunk size
If a chunk was larger than 4GiB, then chunk_data_sz would overflow and
blkcnt would not be calculated correctly. Upgrade it to a u64 and cast
its multiplicands as well. Also fix bytes_written while we're at it.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Kever Yang [Tue, 30 Mar 2021 10:02:07 +0000 (18:02 +0800)]
MAINTAINERS: Update maintainer's mail address
Philipp has change the mail and the legacy one is not available, update it
to the new one.
CC: Philipp Tomsich <philipp.tomsich@vrull.eu>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Tom Rini [Mon, 31 May 2021 14:19:14 +0000 (10:19 -0400)]
Merge https://source.denx.de/u-boot/custodians/u-boot-riscv
- SiFive FU740 and Unmatched support
Tom Rini [Mon, 31 May 2021 14:18:26 +0000 (10:18 -0400)]
Merge https://source.denx.de/u-boot/custodians/u-boot-sunxi
This contains the fix to bring back the SD card as MMC0. In the long run
we are looking into a more robust solution, but for now we need to fix
this, as this breaks the user experience left, right, and centre.
Also add the one MAINTAINERS path addition from Samuel.
Green Wan [Wed, 19 May 2021 11:16:15 +0000 (04:16 -0700)]
drivers: pci: pcie_dw_common: fix Werror compilation error
Fix compilation error when Werror is turned on. The warning could
possible break some CI builds.
Signed-off-by: Green Wan <green.wan@sifive.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Green Wan [Thu, 27 May 2021 13:52:14 +0000 (06:52 -0700)]
riscv: cpu: fu740: clear feature disable CSR
Clear feature disable CSR to turn on all features of hart. The detail
is specified at section, 'SiFive Feature Disable CSR', in user manual
https://sifive.cdn.prismic.io/sifive/
aee0dd4c-d156-496e-a6c4-db0cf54bbe68_sifive_U74MC_rtl_full_20G1.03.00_manual.pdf
Signed-off-by: Green Wan <green.wan@sifive.com>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Green Wan [Thu, 27 May 2021 13:52:13 +0000 (06:52 -0700)]
board: sifive: add HiFive Unmatched board support
Add defconfig and board support for HiFive Unmatched.
Signed-off-by: Green Wan <green.wan@sifive.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Green Wan [Thu, 27 May 2021 13:52:12 +0000 (06:52 -0700)]
riscv: dts: add SiFive Unmatched board support
Add dts files for SiFive Unmatched board.
Signed-off-by: Green Wan <green.wan@sifive.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Green Wan [Thu, 27 May 2021 13:52:11 +0000 (06:52 -0700)]
riscv: dts: add fu740 support
Add dts support for fu740. The HiFive Unmatched support is based on
fu740 cpu and drivers in following patch set.
Signed-off-by: Green Wan <green.wan@sifive.com>
[greentime.hu: set fu740 speed to 1.2GHz]
Signed-off-by: Greentime Hu <greentime.hu@sifive.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Green Wan [Thu, 27 May 2021 13:52:10 +0000 (06:52 -0700)]
drivers: pci: add pcie support for fu740
Add pcie driver for SiFive fu740, the driver depends on
fu740 gpio, clk and reset driver to do init. Force running at Gen1
for better capatible enumeration.
Several devices are tested:
a) M.2 NVMe SSD
b) USB-to-PCI adapter
c) Ethernet adapter (E1000 compatible)
Signed-off-by: Green Wan <green.wan@sifive.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Green Wan [Thu, 27 May 2021 13:52:09 +0000 (06:52 -0700)]
drivers: ram: sifive: rename fu540_ddr and add fu740 support
Rename fu540_ddr.c to sifive_ddr.c and add fu740 support
Signed-off-by: Green Wan <green.wan@sifive.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Green Wan [Thu, 27 May 2021 13:52:08 +0000 (06:52 -0700)]
drivers: clk: add fu740 support
Add fu740 support. One abstract layer is added for supporting
multiple chips such as fu540 and fu740.
Signed-off-by: Green Wan <green.wan@sifive.com>
Green Wan [Thu, 27 May 2021 13:52:07 +0000 (06:52 -0700)]
riscv: cpu: fu740: Add support for cpu fu740
Add SiFive fu740 cpu to support RISC-V arch
Signed-off-by: Green Wan <green.wan@sifive.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Samuel Holland [Mon, 19 Apr 2021 03:13:36 +0000 (22:13 -0500)]
MAINTAINERS: Add allwinner/sunxi driver directories
These drivers are sunxi platform-specific, and so are of interest to the
sunxi maintainers.
In fact, as there is no PHY driver maintainer, drivers/phy/allwinner had
no maintainer at all.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Acked-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Andre Przywara [Fri, 16 Apr 2021 10:52:27 +0000 (11:52 +0100)]
sunxi: Bring back SD card as MMC device 0
Commit
2243d19e5618 ("mmc: mmc-uclass: Use dev_seq() to read aliases
node's index") now actually enforces U-Boot's device enumeration policy,
where explicitly named devices come first, then any other non-named
devices follow, without filling gaps.
For quite a while we have had an "mmc1 = &mmc2;" alias in our
sunxi-u-boot.dtsi, which now leads to the problem that the SD card
(which was always mmc device 0) now gets to be number 2.
This breaks quite some boot scripts, including our own distro boot
commands, and some other features looking at $mmc_bootdev, also
fastboot.
Just add an explicit mmc0 alias in the very same file to fix this and
restore the old behaviour.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reported-by: Samuel Holland <samuel@sholland.org>
Tested-by: Simon Baatz <gmbnomis@gmail.com>
Tom Rini [Fri, 28 May 2021 18:11:06 +0000 (14:11 -0400)]
Merge tag 'u-boot-stm32-
20210528' of https://source.denx.de/u-boot/custodians/u-boot-stm
- DFU: MTD: fix for lock support
- reset: stm32: fix bank bank and offset computation
- enable UNZIP config in several stm32mp defconfig
Tom Rini [Fri, 28 May 2021 18:10:51 +0000 (14:10 -0400)]
Merge tag 'efi-2021-07-rc4-2' of https://source.denx.de/u-boot/custodians/u-boot-efi
Pull request for efi-2021-07-rc4-2
Simplify configuration using HASH functions
Fix Coverity warnings related to EFI TCG2 protocol
Enable PE/COFF image measurement
Masahisa Kojima [Wed, 26 May 2021 03:09:58 +0000 (12:09 +0900)]
efi_loader: add PE/COFF image measurement
"TCG PC Client Platform Firmware Profile Specification"
requires to measure every attempt to load and execute
a OS Loader(a UEFI application) into PCR[4].
This commit adds the PE/COFF image measurement, extends PCR,
and appends measurement into Event Log.
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Tested-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Replace CONFIG_HASH_CALCULATE by CONFIG_HASH
Fix conversions between pointers and u64.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Alexandru Gagniuc [Mon, 24 May 2021 19:28:57 +0000 (14:28 -0500)]
efi_loader: Work-around build issue due to missing hash_calculate()
The hash_calculate() symbol is provided by hash-checksum.c. It depends
on hash_progressive_lookup_algo(), provided when CONFIG_HASH=y.
The issue is that hash_calculate() is used by the efi_loader,
irregardless of CONFIG_FIT_SIGNATURE. As pointed out in
commit
87316da05f2f ("lib: introduce HASH_CALCULATE option"),
enabling hash_calculate() based on CONFIG_FIT_SIGNATURE is incorrect.
To resolve this, use CONFIG_HASH as the compile switch for
hash-checksum.c. This ensures that all dependencies are compiled, and
is the most natural Kconfig to use.
There is the issue of having to 'select HASH' in a couple of places
that already 'select SHA256'. This is a deeper problem with how hashes
are organized, and fixing it is beyonf the scope of this change.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Acked-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Alexandru Gagniuc [Mon, 24 May 2021 19:28:56 +0000 (14:28 -0500)]
Revert "lib: introduce HASH_CALCULATE option"
When we think of Kconfig, we usually think of features that we like
to enable or not. Ideally, we wouldn't use Kconfig to fix a build
issue, although sometimes it might make sense. With Kconfig it's hard
to guarantee that the fix is universal. We can only say that it works
for the set of tested configurations. In the majority of cases, it's
preferable to let the linker figure things out for us.
The reverted commit attempted to fix a build issue by adding an
invisible Kconfig option. This is wrong in several ways:
It invents a new Kconfig variable when CONFIG_HASH already
exists for the same purpose.
Second, hash-checksum.c makes use of the hash_progressive_lookup_algo()
symbol, which is only provided with CONFIG_HASH, but this dependency
was not expressed in the reverted patch.
It feels like Kconfig is turning into a listing of all available
source files, and a buffet to 'select' which ones to compile. The
purpose of this revert is to enable the next change to make use of
CONFIG_HASH instead of adding to Kconfig.
This reverts commit
87316da05f2fd49d3709275e64ef0c5980366ade.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Acked-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Ilias Apalodimas [Wed, 26 May 2021 18:01:00 +0000 (21:01 +0300)]
efi_loader: Fix coverity warnings for efi tcg2 protocol
Coverity reported 3 warnings on the current code.
CID 331856, 331855, 331854 on the latest scan.
Fix the rest of the warnings by initializing the variables before
passing them to tpm2_get_pcr_info().
In order to avoid future warnings and errors initialize them to 0 within
the function as well, since the values are always OR'ed after querying the
hardware.
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Grzegorz Szymaszek [Mon, 19 Apr 2021 17:55:52 +0000 (19:55 +0200)]
arm: dts: stm32mp157c-odyssey-som: enable the RNG1
Enable the true random number generator. It can be used, for example, to
generate partition UUIDs when partitioning with the gpt command. The
generator is already enabled in the device trees of several other
STM32MP1‐based boards, like DKx or DHCOM.
Signed-off-by: Grzegorz Szymaszek <gszymaszek@short.pl>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Patrick Delaunay [Thu, 6 May 2021 07:31:00 +0000 (09:31 +0200)]
configs: stm32mp: Enable UNZIP on STMicroelectronics stm32mp15 boards
The CMD_UNZIP provides the 'gzwrite' command, which is convenient
for writing e.g. gz-compressed images to eMMC from U-Boot.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Marek Vasut [Mon, 3 May 2021 11:31:48 +0000 (13:31 +0200)]
ARM: stm32: Enable UNZIP on DHSOM by default
The CMD_UNZIP provides the 'gzwrite' command, which is convenient
for writing e.g. gz-compressed images to eMMC from U-Boot.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Marek Vasut [Mon, 3 May 2021 11:31:39 +0000 (13:31 +0200)]
ARM: stm32: Add additional ID register check for KSZ8851 presence
Currently the code sets eth1addr only if /ethernet1 alias exists in DT,
the node pointed to by the alias has "micrel,ks8851-mll" compatible
string, and the KSZ8851 CCR register read indicates programmed EEPROM
is not connected.
This is not sufficient to detect cases where the DT still contains the
KSZ8851 nodes, but the chip itself is not present. Extend the detection
to handle these cases.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Christoph Niedermaier [Wed, 5 May 2021 16:23:51 +0000 (18:23 +0200)]
ARM: stm32: Update dhelectronics/dh_stm32mp1/MAINTAINERS file
Adding new DH electronics mailing list.
Signed-off-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Patrice Chotard [Wed, 28 Apr 2021 11:42:45 +0000 (13:42 +0200)]
reset: stm32: Fix bank and offset computation
BITS_PER_LONG is used to represent register's size which is 32.
But when compiled on arch64, BITS_PER_LONG is then equal to 64.
Fix bank and offset computation to make it work on arch32 and
arch64 and ensure that register's size is always equal to 32.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Pankaj Dev <pankaj.dev@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Patrick Delaunay [Wed, 10 Mar 2021 09:27:22 +0000 (10:27 +0100)]
dfu: dfu_mtd: remove the mtd_block_op error when mtd_lock is not supported
Fix the result of DFU_OP_WRITE operation in mtd_block_op function
when mtd_lock is not supported (-EOPNOTSUPP) to avoid DFU stack
error on the DFU manifestation of the MTD device, when
dfu_flush_medium_mtd is called.
Without this patch, dfu-util failed on dfuERROR state at the end
of the write operation on the alternate even if MTD write
opeartion is correctly performed.
$> dfu-util -a 3 -D test.bin
....
DFU mode device DFU version 0110
Device returned transfer size 4096
Copying data from PC to DFU device
....
Download [=========================] 100% 225469 bytes
Download done.
state(10) = dfuERROR, status(14) = Something went wrong,
but the device does not know what it was Done!
Fixes:
65f3fc18fc1e ("dfu_mtd: Add provision to unlock mtd device")
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Acked-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Tom Rini [Thu, 27 May 2021 11:42:49 +0000 (07:42 -0400)]
Merge tag 'ti-v2021.07-rc4' of https://source.denx.de/u-boot/custodians/u-boot-ti
- Fix reset for AM64 platforms
- Enable networking PHY driver for AM64
- Fix default R5F cluster setting in J7
Tom Rini [Thu, 27 May 2021 11:41:25 +0000 (07:41 -0400)]
Merge branch '2021-05-26-assorted-bugfixes'
Faiz Abbas [Mon, 19 Apr 2021 06:50:27 +0000 (12:20 +0530)]
ARM: ti: Increase the allocated size for MLO.raw
MLO has increased to a size greater than the allocated
128 kB in dfu_alt_info_emmc and _mmc.
Therefore, double the allocated size for MLO.raw in
the default environment.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210419065027.5834-1-a-govindraju@ti.com
Suman Anna [Fri, 14 May 2021 01:10:57 +0000 (20:10 -0500)]
arm: dts: k3-am642-sk: Add sysreset controller node
The AM64x SoC uses a central Device Management and Security Controller
(DMSC) processor that manages all the low-level device controls
including the system-wide SoC reset. The system-wide reset is managed
through the system reset driver.
Add a sysreset controller node as a child of the dmsc node to enable
the "reset" command from U-Boot prompt for the K3 AM642 SK.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Suman Anna [Fri, 14 May 2021 01:10:56 +0000 (20:10 -0500)]
arm: dts: k3-am642-evm: Add sysreset controller node
The AM64x SoC uses a central Device Management and Security Controller
(DMSC) processor that manages all the low-level device controls
including the system-wide SoC reset. The system-wide reset is managed
through the system reset driver.
Add a sysreset controller node as a child of the dmsc node to enable
the "reset" command from U-Boot prompt for the K3 AM642 EVM.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Dave Gerlach [Fri, 14 May 2021 01:10:55 +0000 (20:10 -0500)]
firmware: ti_sci: Update ti_sci_msg_req_reboot to include domain
The ti_sci_msg_req_reboot message payload has been extended to include a
domain field, but for the purposes of u-boot this should be zero to
reset the entire SoC as it did before. Include domain for completeness
and set to zero to ensure proper operation.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Suman Anna [Tue, 18 May 2021 21:38:25 +0000 (16:38 -0500)]
arm: dts: k3-j721e: Fix up MAIN R5FSS cluster mode back to Split-mode
The default U-Boot environment variables and design are all set up for
both the MAIN R5FSS clusters to be in Split-mode. This is the setting
in v2021.01 U-Boot and the dt nodes are synched with the kernel binding
property names in commit
468ec2f3ef8f ("remoteproc: k3_r5: Sync to
upstreamed kernel DT property names") merged in v2021.04-rc2.
The modes for both the clusters got switched back to LockStep mode by
mistake in commit
70e167495ab2 ("arm: dts: k3-j721e: Sync Linux v5.11-rc6
dts into U-Boot") also in v2021.04-rc2. This throws the following warning
messages when early-booting the cores using default env variables,
k3_r5f_rproc r5f at 5d00000: Invalid op: Trying to start secondary core 7 in lockstep mode
Load Remote Processor 3 with data at addr=0x82000000 98484 bytes: Failed!
k3_r5f_rproc r5f at 5f00000: Invalid op: Trying to start secondary core 9 in lockstep mode
Load Remote Processor 5 with data at addr=0x82000000 98484 bytes: Failed!
Fix this by switching back both the clusters to the expected Split-mode.
Make this mode change in the u-boot specific dtsi file to avoid such
sync overrides in the future until the kernel dts is also switched to
Split-mode by default.
Fixes:
70e167495ab2 ("arm: dts: k3-j721e: Sync Linux v5.11-rc6 dts into U-Boot")
Reported-by: Minas Hambardzumyan <minas@ti.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Vignesh Raghavendra [Wed, 12 May 2021 14:38:25 +0000 (20:08 +0530)]
configs: am64x_evm_a53_defconfig: Enable DP83867 PHY driver
AM64x GP and SK EVM have DP83867 PHY connected to CPSW external port0.
Enable the driver in order to use ethernet at U-Boot prompt.
CONFIG_PHY_TI is selected by CONFIG_PHY_TI_DP83867 and thus can be dropped.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Sean Anderson [Sun, 23 May 2021 17:00:56 +0000 (13:00 -0400)]
test: Remove duplicate macro
ut_asserteq_strn is defined twice. Remove one definition.
Fixes:
33d7edfd5f ("test: Add a way to check part of a console line or skip it")
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Harm Berntsen [Fri, 21 May 2021 19:59:45 +0000 (21:59 +0200)]
GitLab: Remove tags for sandbox_noinst tests
Commit
712cc962b70d ("GitLab: Remove "tags" stanzas") removed the 'all'
tag from all the jobs. The sandbox_noinst_test.py test was added in
between the author date and commit date (commit
6c914e4232cd
("azure/gitlab: Add tests for sandbox_noinst")) which is probably why it
still contains the tags. This commit fixes that so all jobs now don't
require tags on the GitLab runners.
Signed-off-by: Harm Berntsen <harm.berntsen@nedap.com>
CC: Simon Glass <sjg@chromium.org>
Acked-by: Pratyush Yadav <p.yadav@ti.com>
Alper Nebi Yasak [Thu, 20 May 2021 19:09:46 +0000 (22:09 +0300)]
test: Fix filesystem tests always being skipped
Commit
1ba21bb06b08 ("test: Don't unmount not (yet) mounted system")
fixes an issue in the filesystem tests where the test setup may fail
to mount an image and still attempt to unmount it. However, the commit
unintentionally breaks the test setups in two ways.
The newly created unmounted filesystem images are being immediately
deleted due to some cleanup steps being misplaced into finally blocks,
which makes them always run instead of only on failures. The mount calls
always fail since the images never exist, causing the tests to be always
skipped. This patch moves these cleanup calls into the except blocks to
fix this and makes the tests run again.
There are also unmount calls misplaced into finally blocks, making them
run after the tests instead of before the tests. These unmount calls
make the filesystem image file consistent with the changes made to it as
part of the test setup, and this misplacement is making a number of
tests fail unexpectedly.
The unmount calls must be run before the tests use the image, meaning
before the yield call and not in the finally block. They must also be
run as a cleanup step when the filesystem setup fails, so they can't be
placed as the final call in the try blocks since they would be skipped
on such failures. For these reasons, this patch places the unmount calls
both in the except blocks and the else blocks of the final setup step.
This makes the unexpectedly failing tests to succeed again.
Furthermore, this isolates the mount calls to their own try-except
statement to avoid reintroducing the original issue of unmounting a
not-mounted image while fixing the unmount misplacement.
After these fixes, running "make tests" with guestmount available results
in two test failures not related to the mentioned commit. If the
guestmount executables are unavailable, the mounts fallback to using
sudo and result in no failures.
Fixes:
1ba21bb06b08 ("test: Don't unmount not (yet) mounted system")
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Michal Simek [Thu, 20 May 2021 11:08:44 +0000 (13:08 +0200)]
spl: Kconfig: Use tabs instead of space for alignment
A lot of entries were using spaces instead of tab for alignment that's why
it is good to fix it to use the same style everywhere.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>