Madalin Bucur [Wed, 4 Mar 2020 16:04:25 +0000 (18:04 +0200)]
dt-bindings: net: FMan erratum A050385
FMAN DMA read or writes under heavy traffic load may cause FMAN
internal resource leak; thus stopping further packet processing.
The FMAN internal queue can overflow when FMAN splits single
read or write transactions into multiple smaller transactions
such that more than 17 AXI transactions are in flight from FMAN
to interconnect. When the FMAN internal queue overflows, it can
stall further packet processing. The issue can occur with any one
of the following three conditions:
1. FMAN AXI transaction crosses 4K address boundary (Errata
A010022)
2. FMAN DMA address for an AXI transaction is not 16 byte
aligned, i.e. the last 4 bits of an address are non-zero
3. Scatter Gather (SG) frames have more than one SG buffer in
the SG list and any one of the buffers, except the last
buffer in the SG list has data size that is not a multiple
of 16 bytes, i.e., other than 16, 32, 48, 64, etc.
With any one of the above three conditions present, there is
likelihood of stalled FMAN packet processing, especially under
stress with multiple ports injecting line-rate traffic.
To avoid situations that stall FMAN packet processing, all of the
above three conditions must be avoided; therefore, configure the
system with the following rules:
1. Frame buffers must not span a 4KB address boundary, unless
the frame start address is 256 byte aligned
2. All FMAN DMA start addresses (for example, BMAN buffer
address, FD[address] + FD[offset]) are 16B aligned
3. SG table and buffer addresses are 16B aligned and the size
of SG buffers are multiple of 16 bytes, except for the last
SG buffer that can be of any size.
Additional workaround notes:
- Address alignment of 64 bytes is recommended for maximally
efficient system bus transactions (although 16 byte alignment is
sufficient to avoid the stall condition)
- To support frame sizes that are larger than 4K bytes, there are
two options:
1. Large single buffer frames that span a 4KB page boundary can
be converted into SG frames to avoid transaction splits at
the 4KB boundary,
2. Align the large single buffer to 256B address boundaries,
ensure that the frame address plus offset is 256B aligned.
- If software generated SG frames have buffers that are unaligned
and with random non-multiple of 16 byte lengths, before
transmitting such frames via FMAN, frames will need to be copied
into a new single buffer or multiple buffer SG frame that is
compliant with the three rules listed above.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sat, 7 Mar 2020 05:36:25 +0000 (21:36 -0800)]
Merge git://git./pub/scm/linux/kernel/git/pablo/nf
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes for net:
1) Patches to bump position index from sysctl seq_next,
from Vasilin Averin.
2) Release flowtable hook from error path, from Florian Westphal.
3) Patches to add missing netlink attribute validation,
from Jakub Kicinski.
4) Missing NFTA_CHAIN_FLAGS in nf_tables_fill_chain_info().
5) Infinite loop in module autoload if extension is not available,
from Florian Westphal.
6) Missing module ownership in inet/nat chain type definition.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso [Fri, 6 Mar 2020 16:37:28 +0000 (17:37 +0100)]
netfilter: nft_chain_nat: inet family is missing module ownership
Set owner to THIS_MODULE, otherwise the nft_chain_nat module might be
removed while there are still inet/nat chains in place.
[ 117.942096] BUG: unable to handle page fault for address:
ffffffffa0d5e040
[ 117.942101] #PF: supervisor read access in kernel mode
[ 117.942103] #PF: error_code(0x0000) - not-present page
[ 117.942106] PGD 200c067 P4D 200c067 PUD 200d063 PMD
3dc909067 PTE 0
[ 117.942113] Oops: 0000 [#1] PREEMPT SMP PTI
[ 117.942118] CPU: 3 PID: 27 Comm: kworker/3:0 Not tainted 5.6.0-rc3+ #348
[ 117.942133] Workqueue: events nf_tables_trans_destroy_work [nf_tables]
[ 117.942145] RIP: 0010:nf_tables_chain_destroy.isra.0+0x94/0x15a [nf_tables]
[ 117.942149] Code: f6 45 54 01 0f 84 d1 00 00 00 80 3b 05 74 44 48 8b 75 e8 48 c7 c7 72 be de a0 e8 56 e6 2d e0 48 8b 45 e8 48 c7 c7 7f be de a0 <48> 8b 30 e8 43 e6 2d e0 48 8b 45 e8 48 8b 40 10 48 85 c0 74 5b 8b
[ 117.942152] RSP: 0018:
ffffc9000015be10 EFLAGS:
00010292
[ 117.942155] RAX:
ffffffffa0d5e040 RBX:
ffff88840be87fc2 RCX:
0000000000000007
[ 117.942158] RDX:
0000000000000007 RSI:
0000000000000086 RDI:
ffffffffa0debe7f
[ 117.942160] RBP:
ffff888403b54b50 R08:
0000000000001482 R09:
0000000000000004
[ 117.942162] R10:
0000000000000000 R11:
0000000000000001 R12:
ffff8883eda7e540
[ 117.942164] R13:
dead000000000122 R14:
dead000000000100 R15:
ffff888403b3db80
[ 117.942167] FS:
0000000000000000(0000) GS:
ffff88840e4c0000(0000) knlGS:
0000000000000000
[ 117.942169] CS: 0010 DS: 0000 ES: 0000 CR0:
0000000080050033
[ 117.942172] CR2:
ffffffffa0d5e040 CR3:
00000003e4c52002 CR4:
00000000001606e0
[ 117.942174] Call Trace:
[ 117.942188] nf_tables_trans_destroy_work.cold+0xd/0x12 [nf_tables]
[ 117.942196] process_one_work+0x1d6/0x3b0
[ 117.942200] worker_thread+0x45/0x3c0
[ 117.942203] ? process_one_work+0x3b0/0x3b0
[ 117.942210] kthread+0x112/0x130
[ 117.942214] ? kthread_create_worker_on_cpu+0x40/0x40
[ 117.942221] ret_from_fork+0x35/0x40
nf_tables_chain_destroy() crashes on module_put() because the module is
gone.
Fixes:
d164385ec572 ("netfilter: nat: add inet family nat support")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Paolo Abeni [Wed, 4 Mar 2020 15:51:07 +0000 (16:51 +0100)]
mptcp: always include dack if possible.
Currently passive MPTCP socket can skip including the DACK
option - if the peer sends data before accept() completes.
The above happens because the msk 'can_ack' flag is set
only after the accept() call.
Such missing DACK option may cause - as per RFC spec -
unwanted fallback to TCP.
This change addresses the issue using the key material
available in the current subflow, if any, to create a suitable
dack option when msk ack seq is not yet available.
v1 -> v2:
- adavance the generated ack after the initial MPC packet
Fixes:
d22f4988ffec ("mptcp: process MP_CAPABLE data option")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Carpenter [Wed, 4 Mar 2020 14:24:31 +0000 (17:24 +0300)]
net: nfc: fix bounds checking bugs on "pipe"
This is similar to commit
674d9de02aa7 ("NFC: Fix possible memory
corruption when handling SHDLC I-Frame commands") and commit
d7ee81ad09f0
("NFC: nci: Add some bounds checking in nci_hci_cmd_received()") which
added range checks on "pipe".
The "pipe" variable comes skb->data[0] in nfc_hci_msg_rx_work().
It's in the 0-255 range. We're using it as the array index into the
hdev->pipes[] array which has NFC_HCI_MAX_PIPES (128) members.
Fixes:
118278f20aa8 ("NFC: hci: Add pipes table to reference them with a tuple {gate, host}")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiang Lidong [Wed, 4 Mar 2020 01:49:29 +0000 (09:49 +0800)]
veth: ignore peer tx_dropped when counting local rx_dropped
When local NET_RX backlog is full due to traffic overrun,
peer veth tx_dropped counter increases. At that time, list
local veth stats, rx_dropped has double value of peer
tx_dropped, even bigger than transmit packets by peer.
In NET_RX softirq process, if any packet drop case happens,
it increases dev's rx_dropped counter and returns NET_RX_DROP.
At veth tx side, it records any error returned from peer netif_rx
into local dev tx_dropped counter.
In veth get stats process, it puts local dev rx_dropped and
peer dev tx_dropped into together as local rx_drpped value.
So that it shows double value of real dropped packets number in
this case.
This patch ignores peer tx_dropped when counting local rx_dropped,
since peer tx_dropped is duplicated to local rx_dropped at most cases.
Signed-off-by: Jiang Lidong <jianglidong3@jd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 5 Mar 2020 23:05:31 +0000 (15:05 -0800)]
Merge tag 'wireless-drivers-2020-03-05' of git://git./linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for v5.6
Second set of fixes for v5.6. Only two small fixes this time.
iwlwifi
* fix another initialisation regression with 3168 devices
mt76
* fix memory corruption with too many rx fragments
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Tom Zhao [Thu, 5 Mar 2020 11:38:45 +0000 (11:38 +0000)]
sfc: complete the next packet when we receive a timestamp
We now ignore the "completion" event when using tx queue timestamping,
and only pay attention to the two (high and low) timestamp events. The
NIC will send a pair of timestamp events for every packet transmitted.
The current firmware may merge the completion events, and it is possible
that future versions may reorder the completion and timestamp events.
As such the completion event is not useful.
Without this patch in place a merged completion event on a queue with
timestamping will cause a "spurious TX completion" error. This affects
SFN8000-series adapters.
Signed-off-by: Tom Zhao <tzhao@solarflare.com>
Acked-by: Martin Habets <mhabets@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jian Shen [Thu, 5 Mar 2020 01:47:53 +0000 (09:47 +0800)]
net: hns3: fix a not link up issue when fibre port supports autoneg
When fibre port supports auto-negotiation, the IMP(Intelligent
Management Process) processes the speed of auto-negotiation
and the user's speed separately.
For below case, the port will get a not link up problem.
step 1: disables auto-negotiation and sets speed to A, then
the driver's MAC speed will be updated to A.
step 2: enables auto-negotiation and MAC gets negotiated
speed B, then the driver's MAC speed will be updated to B
through querying in periodical task.
step 3: MAC gets new negotiated speed A.
step 4: disables auto-negotiation and sets speed to B before
periodical task query new MAC speed A, the driver will ignore
the speed configuration.
This patch fixes it by skipping speed and duplex checking when
fibre port supports auto-negotiation.
Fixes:
22f48e24a23d ("net: hns3: add autoneg and change speed support for fibre port")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Wed, 4 Mar 2020 23:51:43 +0000 (15:51 -0800)]
slip: make slhc_compress() more robust against malicious packets
Before accessing various fields in IPV4 network header
and TCP header, make sure the packet :
- Has IP version 4 (ip->version == 4)
- Has not a silly network length (ip->ihl >= 5)
- Is big enough to hold network and transport headers
- Has not a silly TCP header size (th->doff >= sizeof(struct tcphdr) / 4)
syzbot reported :
BUG: KMSAN: uninit-value in slhc_compress+0x5b9/0x2e60 drivers/net/slip/slhc.c:270
CPU: 0 PID: 11728 Comm: syz-executor231 Not tainted 5.6.0-rc2-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x1c9/0x220 lib/dump_stack.c:118
kmsan_report+0xf7/0x1e0 mm/kmsan/kmsan_report.c:118
__msan_warning+0x58/0xa0 mm/kmsan/kmsan_instr.c:215
slhc_compress+0x5b9/0x2e60 drivers/net/slip/slhc.c:270
ppp_send_frame drivers/net/ppp/ppp_generic.c:1637 [inline]
__ppp_xmit_process+0x1902/0x2970 drivers/net/ppp/ppp_generic.c:1495
ppp_xmit_process+0x147/0x2f0 drivers/net/ppp/ppp_generic.c:1516
ppp_write+0x6bb/0x790 drivers/net/ppp/ppp_generic.c:512
do_loop_readv_writev fs/read_write.c:717 [inline]
do_iter_write+0x812/0xdc0 fs/read_write.c:1000
compat_writev+0x2df/0x5a0 fs/read_write.c:1351
do_compat_pwritev64 fs/read_write.c:1400 [inline]
__do_compat_sys_pwritev fs/read_write.c:1420 [inline]
__se_compat_sys_pwritev fs/read_write.c:1414 [inline]
__ia32_compat_sys_pwritev+0x349/0x3f0 fs/read_write.c:1414
do_syscall_32_irqs_on arch/x86/entry/common.c:339 [inline]
do_fast_syscall_32+0x3c7/0x6e0 arch/x86/entry/common.c:410
entry_SYSENTER_compat+0x68/0x77 arch/x86/entry/entry_64_compat.S:139
RIP: 0023:0xf7f7cd99
Code: 90 e8 0b 00 00 00 f3 90 0f ae e8 eb f9 8d 74 26 00 89 3c 24 c3 90 90 90 90 90 90 90 90 90 90 90 90 51 52 55 89 e5 0f 34 cd 80 <5d> 5a 59 c3 90 90 90 90 eb 0d 90 90 90 90 90 90 90 90 90 90 90 90
RSP: 002b:
00000000ffdb84ac EFLAGS:
00000217 ORIG_RAX:
000000000000014e
RAX:
ffffffffffffffda RBX:
0000000000000003 RCX:
00000000200001c0
RDX:
0000000000000001 RSI:
0000000000000000 RDI:
0000000000000003
RBP:
0000000040047459 R08:
0000000000000000 R09:
0000000000000000
R10:
0000000000000000 R11:
0000000000000000 R12:
0000000000000000
R13:
0000000000000000 R14:
0000000000000000 R15:
0000000000000000
Uninit was created at:
kmsan_save_stack_with_flags mm/kmsan/kmsan.c:144 [inline]
kmsan_internal_poison_shadow+0x66/0xd0 mm/kmsan/kmsan.c:127
kmsan_slab_alloc+0x8a/0xe0 mm/kmsan/kmsan_hooks.c:82
slab_alloc_node mm/slub.c:2793 [inline]
__kmalloc_node_track_caller+0xb40/0x1200 mm/slub.c:4401
__kmalloc_reserve net/core/skbuff.c:142 [inline]
__alloc_skb+0x2fd/0xac0 net/core/skbuff.c:210
alloc_skb include/linux/skbuff.h:1051 [inline]
ppp_write+0x115/0x790 drivers/net/ppp/ppp_generic.c:500
do_loop_readv_writev fs/read_write.c:717 [inline]
do_iter_write+0x812/0xdc0 fs/read_write.c:1000
compat_writev+0x2df/0x5a0 fs/read_write.c:1351
do_compat_pwritev64 fs/read_write.c:1400 [inline]
__do_compat_sys_pwritev fs/read_write.c:1420 [inline]
__se_compat_sys_pwritev fs/read_write.c:1414 [inline]
__ia32_compat_sys_pwritev+0x349/0x3f0 fs/read_write.c:1414
do_syscall_32_irqs_on arch/x86/entry/common.c:339 [inline]
do_fast_syscall_32+0x3c7/0x6e0 arch/x86/entry/common.c:410
entry_SYSENTER_compat+0x68/0x77 arch/x86/entry/entry_64_compat.S:139
Fixes:
b5451d783ade ("slip: Move the SLIP drivers")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Westphal [Thu, 5 Mar 2020 10:15:36 +0000 (11:15 +0100)]
netfilter: nf_tables: fix infinite loop when expr is not available
nft will loop forever if the kernel doesn't support an expression:
1. nft_expr_type_get() appends the family specific name to the module list.
2. -EAGAIN is returned to nfnetlink, nfnetlink calls abort path.
3. abort path sets ->done to true and calls request_module for the
expression.
4. nfnetlink replays the batch, we end up in nft_expr_type_get() again.
5. nft_expr_type_get attempts to append family-specific name. This
one already exists on the list, so we continue
6. nft_expr_type_get adds the generic expression name to the module
list. -EAGAIN is returned, nfnetlink calls abort path.
7. abort path encounters the family-specific expression which
has 'done' set, so it gets removed.
8. abort path requests the generic expression name, sets done to true.
9. batch is replayed.
If the expression could not be loaded, then we will end up back at 1),
because the family-specific name got removed and the cycle starts again.
Note that userspace can SIGKILL the nft process to stop the cycle, but
the desired behaviour is to return an error after the generic expr name
fails to load the expression.
Fixes:
eb014de4fd418 ("netfilter: nf_tables: autoload modules from the abort path")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Pablo Neira Ayuso [Tue, 3 Mar 2020 14:02:45 +0000 (15:02 +0100)]
netfilter: nf_tables: dump NFTA_CHAIN_FLAGS attribute
Missing NFTA_CHAIN_FLAGS netlink attribute when dumping basechain
definitions.
Fixes:
c9626a2cbdb2 ("netfilter: nf_tables: add hardware offload support")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Dajun Jin [Tue, 3 Mar 2020 04:24:21 +0000 (20:24 -0800)]
drivers/of/of_mdio.c:fix of_mdiobus_register()
When registers a phy_device successful, should terminate the loop
or the phy_device would be registered in other addr. If there are
multiple PHYs without reg properties, it will go wrong.
Signed-off-by: Dajun Jin <adajunjin@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vishal Kulkarni [Mon, 2 Mar 2020 05:24:13 +0000 (10:54 +0530)]
cxgb4: fix checks for max queues to allocate
Hardware can support more than 8 queues currently limited by
netif_get_num_default_rss_queues(). So, rework and fix checks for max
number of queues to allocate. The checks should be based on how many are
actually supported by hardware, OR the number of online cpus; whichever
is lower.
Fixes:
5952dde72307 ("cxgb4: set maximal number of default RSS queues")
Signed-off-by: Vishal Kulkarni <vishal@chelsio.com>"
Signed-off-by: David S. Miller <davem@davemloft.net>
Hauke Mehrtens [Sun, 1 Mar 2020 23:55:02 +0000 (00:55 +0100)]
phylink: Improve error message when validate failed
This should improve the error message when the PHY validate in the MAC
driver failed. I ran into this problem multiple times that I put wrong
interface values into the device tree and was searching why it is
failing with -22 (-EINVAL). This should make it easier to spot the
problem.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jonas Gorski [Mon, 2 Mar 2020 19:46:57 +0000 (20:46 +0100)]
net: phy: bcm63xx: fix OOPS due to missing driver name
719655a14971 ("net: phy: Replace phy driver features u32 with link_mode
bitmap") was a bit over-eager and also removed the second phy driver's
name, resulting in a nasty OOPS on registration:
[ 1.319854] CPU 0 Unable to handle kernel paging request at virtual address
00000000, epc ==
804dd50c, ra ==
804dd4f0
[ 1.330859] Oops[#1]:
[ 1.333138] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 5.4.22 #0
[ 1.339217] $ 0 :
00000000 00000001 87ca7f00 805c1874
[ 1.344590] $ 4 :
00000000 00000047 00585000 8701f800
[ 1.349965] $ 8 :
8701f800 804f4a5c 00000003 64726976
[ 1.355341] $12 :
00000001 00000000 00000000 00000114
[ 1.360718] $16 :
87ca7f80 00000000 00000000 80639fe4
[ 1.366093] $20 :
00000002 00000000 806441d0 80b90000
[ 1.371470] $24 :
00000000 00000000
[ 1.376847] $28 :
87c1e000 87c1fda0 80b90000 804dd4f0
[ 1.382224] Hi :
d1c8f8da
[ 1.385180] Lo :
5518a480
[ 1.388182] epc :
804dd50c kset_find_obj+0x3c/0x114
[ 1.393345] ra :
804dd4f0 kset_find_obj+0x20/0x114
[ 1.398530] Status:
10008703 KERNEL EXL IE
[ 1.402833] Cause :
00800008 (ExcCode 02)
[ 1.406952] BadVA :
00000000
[ 1.409913] PrId :
0002a075 (Broadcom BMIPS4350)
[ 1.414745] Modules linked in:
[ 1.417895] Process swapper/0 (pid: 1, threadinfo=(ptrval), task=(ptrval), tls=
00000000)
[ 1.426214] Stack :
87cec000 80630000 80639370 80640658 80640000 80049af4 80639fe4 8063a0d8
[ 1.434816]
8063a0d8 802ef078 00000002 00000000 806441d0 80b90000 8063a0d8 802ef114
[ 1.443417]
87cea0de 87c1fde0 00000000 804de488 87cea000 8063a0d8 8063a0d8 80334e48
[ 1.452018]
80640000 8063984c 80639bf4 00000000 8065de48 00000001 8063a0d8 80334ed0
[ 1.460620]
806441d0 80b90000 80b90000 802ef164 8065dd70 80620000 80b90000 8065de58
[ 1.469222] ...
[ 1.471734] Call Trace:
[ 1.474255] [<
804dd50c>] kset_find_obj+0x3c/0x114
[ 1.479141] [<
802ef078>] driver_find+0x1c/0x44
[ 1.483665] [<
802ef114>] driver_register+0x74/0x148
[ 1.488719] [<
80334e48>] phy_driver_register+0x9c/0xd0
[ 1.493968] [<
80334ed0>] phy_drivers_register+0x54/0xe8
[ 1.499345] [<
8001061c>] do_one_initcall+0x7c/0x1f4
[ 1.504374] [<
80644ed8>] kernel_init_freeable+0x1d4/0x2b4
[ 1.509940] [<
804f4e24>] kernel_init+0x10/0xf8
[ 1.514502] [<
80018e68>] ret_from_kernel_thread+0x14/0x1c
[ 1.520040] Code:
1060000c 02202025 90650000 <
90810000>
24630001 14250004 24840001 14a0fffb 90650000
[ 1.530061]
[ 1.531698] ---[ end trace
d52f1717cd29bdc8 ]---
Fix it by readding the name.
Fixes:
719655a14971 ("net: phy: Replace phy driver features u32 with link_mode bitmap")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jacob Keller [Mon, 2 Mar 2020 22:21:19 +0000 (14:21 -0800)]
devlink: remove trigger command from devlink-region.rst
The devlink trigger command does not exist. While rewriting the
documentation for devlink into the reStructuredText format,
documentation for the trigger command was accidentally merged in. This
occurred because the author was also working on a potential extension to
devlink regions which included this trigger command, and accidentally
squashed the documentation incorrectly.
Further review eventually settled on using the previously unused "new"
command instead of creating a new trigger command.
Fix this by removing mention of the trigger command from the
documentation.
Fixes:
0b0f945f5458 ("devlink: add a file documenting devlink regions", 2020-01-10)
Noticed-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Tue, 3 Mar 2020 05:08:33 +0000 (21:08 -0800)]
netfilter: nft_tunnel: add missing attribute validation for tunnels
Add missing attribute validation for tunnel source and
destination ports to the netlink policy.
Fixes:
af308b94a2a4 ("netfilter: nf_tables: add tunnel support")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Jakub Kicinski [Tue, 3 Mar 2020 05:08:32 +0000 (21:08 -0800)]
netfilter: nft_payload: add missing attribute validation for payload csum flags
Add missing attribute validation for NFTA_PAYLOAD_CSUM_FLAGS
to the netlink policy.
Fixes:
1814096980bb ("netfilter: nft_payload: layer 4 checksum adjustment for pseudoheader fields")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Jakub Kicinski [Tue, 3 Mar 2020 05:08:31 +0000 (21:08 -0800)]
netfilter: cthelper: add missing attribute validation for cthelper
Add missing attribute validation for cthelper
to the netlink policy.
Fixes:
12f7a505331e ("netfilter: add user-space connection tracking helper infrastructure")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Florian Westphal [Mon, 2 Mar 2020 20:58:50 +0000 (21:58 +0100)]
netfilter: nf_tables: free flowtable hooks on hook register error
If hook registration fails, the hooks allocated via nft_netdev_hook_alloc
need to be freed.
We can't change the goto label to 'goto 5' -- while it does fix the memleak
it does cause a warning splat from the netfilter core (the hooks were not
registered).
Fixes:
3f0465a9ef02 ("netfilter: nf_tables: dynamically allocate hooks per net_device in flowtables")
Reported-by: syzbot+a2ff6fa45162a5ed4dd3@syzkaller.appspotmail.com
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Vasily Averin [Tue, 25 Feb 2020 07:07:12 +0000 (10:07 +0300)]
netfilter: x_tables: xt_mttg_seq_next should increase position index
If .next function does not change position index,
following .show function will repeat output related
to current position index.
Without patch:
# dd if=/proc/net/ip_tables_matches # original file output
conntrack
conntrack
conntrack
recent
recent
icmp
udplite
udp
tcp
0+1 records in
0+1 records out
65 bytes copied, 5.4074e-05 s, 1.2 MB/s
# dd if=/proc/net/ip_tables_matches bs=62 skip=1
dd: /proc/net/ip_tables_matches: cannot skip to specified offset
cp <<< end of last line
tcp <<< and then unexpected whole last line once again
0+1 records in
0+1 records out
7 bytes copied, 0.
000102447 s, 68.3 kB/s
Cc: stable@vger.kernel.org
Fixes:
1f4aace60b0e ("fs/seq_file.c: simplify seq_file iteration code ...")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=206283
Signed-off-by: Vasily Averin <vvs@virtuozzo.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Vasily Averin [Tue, 25 Feb 2020 07:06:29 +0000 (10:06 +0300)]
netfilter: xt_recent: recent_seq_next should increase position index
If .next function does not change position index,
following .show function will repeat output related
to current position index.
Without the patch:
# dd if=/proc/net/xt_recent/SSH # original file outpt
src=127.0.0.4 ttl: 0 last_seen:
6275444819 oldest_pkt: 1
6275444819
src=127.0.0.2 ttl: 0 last_seen:
6275438906 oldest_pkt: 1
6275438906
src=127.0.0.3 ttl: 0 last_seen:
6275441953 oldest_pkt: 1
6275441953
0+1 records in
0+1 records out
204 bytes copied, 6.1332e-05 s, 3.3 MB/s
Read after lseek into middle of last line (offset 140 in example below)
generates expected end of last line and then unexpected whole last line
once again
# dd if=/proc/net/xt_recent/SSH bs=140 skip=1
dd: /proc/net/xt_recent/SSH: cannot skip to specified offset
127.0.0.3 ttl: 0 last_seen:
6275441953 oldest_pkt: 1
6275441953
src=127.0.0.3 ttl: 0 last_seen:
6275441953 oldest_pkt: 1
6275441953
0+1 records in
0+1 records out
132 bytes copied, 6.2487e-05 s, 2.1 MB/s
Cc: stable@vger.kernel.org
Fixes:
1f4aace60b0e ("fs/seq_file.c: simplify seq_file iteration code ...")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=206283
Signed-off-by: Vasily Averin <vvs@virtuozzo.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Vasily Averin [Tue, 25 Feb 2020 07:05:59 +0000 (10:05 +0300)]
netfilter: synproxy: synproxy_cpu_seq_next should increase position index
If .next function does not change position index,
following .show function will repeat output related
to current position index.
Cc: stable@vger.kernel.org
Fixes:
1f4aace60b0e ("fs/seq_file.c: simplify seq_file iteration code ...")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=206283
Signed-off-by: Vasily Averin <vvs@virtuozzo.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Vasily Averin [Tue, 25 Feb 2020 07:05:47 +0000 (10:05 +0300)]
netfilter: nf_conntrack: ct_cpu_seq_next should increase position index
If .next function does not change position index,
following .show function will repeat output related
to current position index.
Cc: stable@vger.kernel.org
Fixes:
1f4aace60b0e ("fs/seq_file.c: simplify seq_file iteration code ...")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=206283
Signed-off-by: Vasily Averin <vvs@virtuozzo.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Jonathan Neuschäfer [Tue, 3 Mar 2020 20:22:05 +0000 (21:22 +0100)]
docs: networking: net_failover: Fix a few typos
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Tue, 3 Mar 2020 15:01:46 +0000 (15:01 +0000)]
net: dsa: fix phylink_start()/phylink_stop() calls
Place phylink_start()/phylink_stop() inside dsa_port_enable() and
dsa_port_disable(), which ensures that we call phylink_stop() before
tearing down phylink - which is a documented requirement. Failure
to do so can cause use-after-free bugs.
Fixes:
0e27921816ad ("net: dsa: Use PHYLINK for the CPU/DSA ports")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 3 Mar 2020 22:43:17 +0000 (14:43 -0800)]
Merge branch 'Fix-IPv6-peer-route-update'
Hangbin Liu says:
====================
Fix IPv6 peer route update
Currently we have two issues for peer route update on IPv6.
1. When update peer route metric, we only updated the local one.
2. If peer address changed, we didn't remove the old one and add new one.
The first two patches fixed these issues and the third patch add new
tests to cover it.
With the fixes and updated test:
]# ./fib_tests.sh
IPv6 prefix route tests
TEST: Default metric [ OK ]
TEST: User specified metric on first device [ OK ]
TEST: User specified metric on second device [ OK ]
TEST: Delete of address on first device [ OK ]
TEST: Modify metric of address [ OK ]
TEST: Prefix route removed on link down [ OK ]
TEST: Prefix route with metric on link up [ OK ]
TEST: Set metric with peer route on local side [ OK ]
TEST: User specified metric on local address [ OK ]
TEST: Set metric with peer route on peer side [ OK ]
TEST: Modify metric with peer route on local side [ OK ]
TEST: Modify metric with peer route on peer side [ OK ]
IPv4 prefix route tests
TEST: Default metric [ OK ]
TEST: User specified metric on first device [ OK ]
TEST: User specified metric on second device [ OK ]
TEST: Delete of address on first device [ OK ]
TEST: Modify metric of address [ OK ]
TEST: Prefix route removed on link down [ OK ]
TEST: Prefix route with metric on link up [ OK ]
TEST: Modify metric of .0/24 address [ OK ]
TEST: Set metric of address with peer route [ OK ]
TEST: Modify metric of address with peer route [ OK ]
Tests passed: 22
Tests failed: 0
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Hangbin Liu [Tue, 3 Mar 2020 06:37:36 +0000 (14:37 +0800)]
selftests/net/fib_tests: update addr_metric_test for peer route testing
This patch update {ipv4, ipv6}_addr_metric_test with
1. Set metric of address with peer route and see if the route added
correctly.
2. Modify metric and peer address for peer route and see if the route
changed correctly.
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hangbin Liu [Tue, 3 Mar 2020 06:37:35 +0000 (14:37 +0800)]
net/ipv6: remove the old peer route if change it to a new one
When we modify the peer route and changed it to a new one, we should
remove the old route first. Before the fix:
+ ip addr add dev dummy1 2001:db8::1 peer 2001:db8::2
+ ip -6 route show dev dummy1
2001:db8::1 proto kernel metric 256 pref medium
2001:db8::2 proto kernel metric 256 pref medium
+ ip addr change dev dummy1 2001:db8::1 peer 2001:db8::3
+ ip -6 route show dev dummy1
2001:db8::1 proto kernel metric 256 pref medium
2001:db8::2 proto kernel metric 256 pref medium
After the fix:
+ ip addr change dev dummy1 2001:db8::1 peer 2001:db8::3
+ ip -6 route show dev dummy1
2001:db8::1 proto kernel metric 256 pref medium
2001:db8::3 proto kernel metric 256 pref medium
This patch depend on the previous patch "net/ipv6: need update peer route
when modify metric" to update new peer route after delete old one.
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hangbin Liu [Tue, 3 Mar 2020 06:37:34 +0000 (14:37 +0800)]
net/ipv6: need update peer route when modify metric
When we modify the route metric, the peer address's route need also
be updated. Before the fix:
+ ip addr add dev dummy1 2001:db8::1 peer 2001:db8::2 metric 60
+ ip -6 route show dev dummy1
2001:db8::1 proto kernel metric 60 pref medium
2001:db8::2 proto kernel metric 60 pref medium
+ ip addr change dev dummy1 2001:db8::1 peer 2001:db8::2 metric 61
+ ip -6 route show dev dummy1
2001:db8::1 proto kernel metric 61 pref medium
2001:db8::2 proto kernel metric 60 pref medium
After the fix:
+ ip addr change dev dummy1 2001:db8::1 peer 2001:db8::2 metric 61
+ ip -6 route show dev dummy1
2001:db8::1 proto kernel metric 61 pref medium
2001:db8::2 proto kernel metric 61 pref medium
Fixes:
8308f3ff1753 ("net/ipv6: Add support for specifying metric of connected routes")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 3 Mar 2020 21:28:49 +0000 (13:28 -0800)]
Merge branch 'net-add-missing-netlink-policies'
Jakub Kicinski says:
====================
net: add missing netlink policies
Recent one-off fixes motivated me to do some grepping for
more missing netlink attribute policies. I didn't manage
to even produce a KASAN splat with these, but it should
be possible with sufficient luck. All the missing policies
are pretty trivial (NLA_Uxx).
I've only tested the devlink patches, the rest compiles.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Tue, 3 Mar 2020 05:05:26 +0000 (21:05 -0800)]
nfc: add missing attribute validation for vendor subcommand
Add missing attribute validation for vendor subcommand attributes
to the netlink policy.
Fixes:
9e58095f9660 ("NFC: netlink: Implement vendor command support")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Tue, 3 Mar 2020 05:05:25 +0000 (21:05 -0800)]
nfc: add missing attribute validation for deactivate target
Add missing attribute validation for NFC_ATTR_TARGET_INDEX
to the netlink policy.
Fixes:
4d63adfe12dd ("NFC: Add NFC_CMD_DEACTIVATE_TARGET support")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Tue, 3 Mar 2020 05:05:24 +0000 (21:05 -0800)]
nfc: add missing attribute validation for SE API
Add missing attribute validation for NFC_ATTR_SE_INDEX
to the netlink policy.
Fixes:
5ce3f32b5264 ("NFC: netlink: SE API implementation")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Tue, 3 Mar 2020 05:05:23 +0000 (21:05 -0800)]
tipc: add missing attribute validation for MTU property
Add missing attribute validation for TIPC_NLA_PROP_MTU
to the netlink policy.
Fixes:
901271e0403a ("tipc: implement configuration of UDP media MTU")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Tue, 3 Mar 2020 05:05:22 +0000 (21:05 -0800)]
team: add missing attribute validation for array index
Add missing attribute validation for TEAM_ATTR_OPTION_ARRAY_INDEX
to the netlink policy.
Fixes:
b13033262d24 ("team: introduce array options")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Tue, 3 Mar 2020 05:05:21 +0000 (21:05 -0800)]
team: add missing attribute validation for port ifindex
Add missing attribute validation for TEAM_ATTR_OPTION_PORT_IFINDEX
to the netlink policy.
Fixes:
80f7c6683fe0 ("team: add support for per-port options")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Tue, 3 Mar 2020 05:05:20 +0000 (21:05 -0800)]
net: taprio: add missing attribute validation for txtime delay
Add missing attribute validation for TCA_TAPRIO_ATTR_TXTIME_DELAY
to the netlink policy.
Fixes:
4cfd5779bd6e ("taprio: Add support for txtime-assist mode")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Tue, 3 Mar 2020 05:05:19 +0000 (21:05 -0800)]
net: fq: add missing attribute validation for orphan mask
Add missing attribute validation for TCA_FQ_ORPHAN_MASK
to the netlink policy.
Fixes:
06eb395fa985 ("pkt_sched: fq: better control of DDOS traffic")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Tue, 3 Mar 2020 05:05:18 +0000 (21:05 -0800)]
openvswitch: add missing attribute validation for hash
Add missing attribute validation for OVS_PACKET_ATTR_HASH
to the netlink policy.
Fixes:
bd1903b7c459 ("net: openvswitch: add hash info to upcall")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Greg Rose <gvrose8192@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Tue, 3 Mar 2020 05:05:17 +0000 (21:05 -0800)]
macsec: add missing attribute validation for port
Add missing attribute validation for IFLA_MACSEC_PORT
to the netlink policy.
Fixes:
c09440f7dcb3 ("macsec: introduce IEEE 802.1AE driver")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Tue, 3 Mar 2020 05:05:16 +0000 (21:05 -0800)]
can: add missing attribute validation for termination
Add missing attribute validation for IFLA_CAN_TERMINATION
to the netlink policy.
Fixes:
12a6075cabc0 ("can: dev: add CAN interface termination API")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Tue, 3 Mar 2020 05:05:15 +0000 (21:05 -0800)]
nl802154: add missing attribute validation for dev_type
Add missing attribute type validation for IEEE802154_ATTR_DEV_TYPE
to the netlink policy.
Fixes:
90c049b2c6ae ("ieee802154: interface type to be added")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Tue, 3 Mar 2020 05:05:14 +0000 (21:05 -0800)]
nl802154: add missing attribute validation
Add missing attribute validation for several u8 types.
Fixes:
2c21d11518b6 ("net: add NL802154 interface for configuration of 802.15.4 devices")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Tue, 3 Mar 2020 05:05:13 +0000 (21:05 -0800)]
fib: add missing attribute validation for tun_id
Add missing netlink policy entry for FRA_TUN_ID.
Fixes:
e7030878fc84 ("fib: Add fib rule match on tunnel id")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Tue, 3 Mar 2020 05:05:12 +0000 (21:05 -0800)]
devlink: validate length of region addr/len
DEVLINK_ATTR_REGION_CHUNK_ADDR and DEVLINK_ATTR_REGION_CHUNK_LEN
lack entries in the netlink policy. Corresponding nla_get_u64()s
may read beyond the end of the message.
Fixes:
4e54795a27f5 ("devlink: Add support for region snapshot read command")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Tue, 3 Mar 2020 05:05:11 +0000 (21:05 -0800)]
devlink: validate length of param values
DEVLINK_ATTR_PARAM_VALUE_DATA may have different types
so it's not checked by the normal netlink policy. Make
sure the attribute length is what we expect.
Fixes:
e3b7ca18ad7b ("devlink: Add param set command")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Felix Fietkau [Thu, 20 Feb 2020 11:41:39 +0000 (12:41 +0100)]
mt76: fix array overflow on receiving too many fragments for a packet
If the hardware receives an oversized packet with too many rx fragments,
skb_shinfo(skb)->frags can overflow and corrupt memory of adjacent pages.
This becomes especially visible if it corrupts the freelist pointer of
a slab page.
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
David S. Miller [Mon, 2 Mar 2020 03:15:27 +0000 (19:15 -0800)]
Merge branch 'bnxt_en-2-bug-fixes'
Michael Chan says:
====================
bnxt_en: 2 bug fixes.
This first patch fixes a rare but possible crash in pci_disable_msix()
when the MTU is changed. The 2nd patch fixes a regression in error
code handling when flashing a file to NVRAM.
Please also queue these for -stable. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Edwin Peer [Mon, 2 Mar 2020 03:07:18 +0000 (22:07 -0500)]
bnxt_en: fix error handling when flashing from file
After bnxt_hwrm_do_send_message() was updated to return standard error
codes in a recent commit, a regression in bnxt_flash_package_from_file()
was introduced. The return value does not properly reflect all
possible firmware errors when calling firmware to flash the package.
Fix it by consolidating all errors in one local variable rc instead
of having 2 variables for different errors.
Fixes:
d4f1420d3656 ("bnxt_en: Convert error code in firmware message response to standard code.")
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vasundhara Volam [Mon, 2 Mar 2020 03:07:17 +0000 (22:07 -0500)]
bnxt_en: reinitialize IRQs when MTU is modified
MTU changes may affect the number of IRQs so we must call
bnxt_close_nic()/bnxt_open_nic() with the irq_re_init parameter
set to true. The reason is that a larger MTU may require
aggregation rings not needed with smaller MTU. We may not be
able to allocate the required number of aggregation rings and
so we reduce the number of channels which will change the number
of IRQs. Without this patch, it may crash eventually in
pci_disable_msix() when the IRQs are not properly unwound.
Fixes:
c0c050c58d84 ("bnxt_en: New Broadcom ethernet driver.")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Heiner Kallweit [Sun, 1 Mar 2020 20:36:09 +0000 (21:36 +0100)]
net: phy: avoid clearing PHY interrupts twice in irq handler
On all PHY drivers that implement did_interrupt() reading the interrupt
status bits clears them. This means we may loose an interrupt that
is triggered between calling did_interrupt() and phy_clear_interrupt().
As part of the fix make it a requirement that did_interrupt() clears
the interrupt.
The Fixes tag refers to the first commit where the patch applies
cleanly.
Fixes:
49644e68f472 ("net: phy: add callback for custom interrupt handler to struct phy_driver")
Reported-by: Michael Walle <michael@walle.cc>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Sat, 29 Feb 2020 20:30:07 +0000 (22:30 +0200)]
net: dsa: sja1105: Don't destroy not-yet-created xmit_worker
Fixes the following NULL pointer dereference on PHY connect error path
teardown:
[ 2.291010] sja1105 spi0.1: Probed switch chip: SJA1105T
[ 2.310044] sja1105 spi0.1: Enabled switch tagging
[ 2.314970] fsl-gianfar soc:ethernet@2d90000 eth2: error -19 setting up slave phy
[ 2.322463] 8<--- cut here ---
[ 2.325497] Unable to handle kernel NULL pointer dereference at virtual address
00000018
[ 2.333555] pgd = (ptrval)
[ 2.336241] [
00000018] *pgd=
00000000
[ 2.339797] Internal error: Oops: 5 [#1] SMP ARM
[ 2.344384] Modules linked in:
[ 2.347420] CPU: 1 PID: 64 Comm: kworker/1:1 Not tainted 5.5.0-rc5 #1
[ 2.353820] Hardware name: Freescale LS1021A
[ 2.358070] Workqueue: events deferred_probe_work_func
[ 2.363182] PC is at kthread_destroy_worker+0x4/0x74
[ 2.368117] LR is at sja1105_teardown+0x70/0xb4
[ 2.372617] pc : [<
c036cdd4>] lr : [<
c0b89238>] psr:
60000013
[ 2.378845] sp :
eeac3d30 ip :
eeab1900 fp :
eef45480
[ 2.384036] r10:
eef4549c r9 :
00000001 r8 :
00000000
[ 2.389227] r7 :
eef527c0 r6 :
00000034 r5 :
ed8ddd0c r4 :
ed8ddc40
[ 2.395714] r3 :
00000000 r2 :
00000000 r1 :
eef4549c r0 :
00000000
[ 2.402204] Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment none
[ 2.409297] Control:
10c5387d Table:
8020406a DAC:
00000051
[ 2.415008] Process kworker/1:1 (pid: 64, stack limit = 0x(ptrval))
[ 2.421237] Stack: (0xeeac3d30 to 0xeeac4000)
[ 2.612635] [<
c036cdd4>] (kthread_destroy_worker) from [<
c0b89238>] (sja1105_teardown+0x70/0xb4)
[ 2.621379] [<
c0b89238>] (sja1105_teardown) from [<
c10717fc>] (dsa_switch_teardown.part.1+0x48/0x74)
[ 2.630467] [<
c10717fc>] (dsa_switch_teardown.part.1) from [<
c1072438>] (dsa_register_switch+0x8b0/0xbf4)
[ 2.639984] [<
c1072438>] (dsa_register_switch) from [<
c0b89c30>] (sja1105_probe+0x2ac/0x464)
[ 2.648378] [<
c0b89c30>] (sja1105_probe) from [<
c0b11a5c>] (spi_drv_probe+0x7c/0xa0)
[ 2.656081] [<
c0b11a5c>] (spi_drv_probe) from [<
c0a26ab8>] (really_probe+0x208/0x480)
[ 2.663871] [<
c0a26ab8>] (really_probe) from [<
c0a26f0c>] (driver_probe_device+0x78/0x1c4)
[ 2.672093] [<
c0a26f0c>] (driver_probe_device) from [<
c0a24c48>] (bus_for_each_drv+0x80/0xc4)
[ 2.680574] [<
c0a24c48>] (bus_for_each_drv) from [<
c0a26810>] (__device_attach+0xd0/0x168)
[ 2.688794] [<
c0a26810>] (__device_attach) from [<
c0a259d8>] (bus_probe_device+0x84/0x8c)
[ 2.696927] [<
c0a259d8>] (bus_probe_device) from [<
c0a25f24>] (deferred_probe_work_func+0x84/0xc4)
[ 2.705842] [<
c0a25f24>] (deferred_probe_work_func) from [<
c03667b0>] (process_one_work+0x22c/0x560)
[ 2.714926] [<
c03667b0>] (process_one_work) from [<
c0366d8c>] (worker_thread+0x2a8/0x5d4)
[ 2.723059] [<
c0366d8c>] (worker_thread) from [<
c036cf94>] (kthread+0x150/0x154)
[ 2.730416] [<
c036cf94>] (kthread) from [<
c03010e8>] (ret_from_fork+0x14/0x2c)
Checking for NULL pointer is correct because the per-port xmit kernel
threads are created in sja1105_probe immediately after calling
dsa_register_switch.
Fixes:
a68578c20a96 ("net: dsa: Make deferred_xmit private to sja1105")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hangbin Liu [Sat, 29 Feb 2020 09:27:13 +0000 (17:27 +0800)]
net/ipv6: use configured metric when add peer route
When we add peer address with metric configured, IPv4 could set the dest
metric correctly, but IPv6 do not. e.g.
]# ip addr add 192.0.2.1 peer 192.0.2.2/32 dev eth1 metric 20
]# ip route show dev eth1
192.0.2.2 proto kernel scope link src 192.0.2.1 metric 20
]# ip addr add 2001:db8::1 peer 2001:db8::2/128 dev eth1 metric 20
]# ip -6 route show dev eth1
2001:db8::1 proto kernel metric 20 pref medium
2001:db8::2 proto kernel metric 256 pref medium
Fix this by using configured metric instead of default one.
Reported-by: Jianlin Shi <jishi@redhat.com>
Fixes:
8308f3ff1753 ("net/ipv6: Add support for specifying metric of connected routes")
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Fri, 28 Feb 2020 19:39:41 +0000 (19:39 +0000)]
net: dsa: mv88e6xxx: fix lockup on warm boot
If the switch is not hardware reset on a warm boot, interrupts can be
left enabled, and possibly pending. This will cause us to enter an
infinite loop trying to service an interrupt we are unable to handle,
thereby preventing the kernel from booting.
Ensure that the global 2 interrupt sources are disabled before we claim
the parent interrupt.
Observed on the ZII development revision B and C platforms with
reworked serdes support, and using reboot -f to reboot the platform.
Fixes:
dc30c35be720 ("net: dsa: mv88e6xxx: Implement interrupt support.")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Randy Dunlap [Fri, 28 Feb 2020 02:09:44 +0000 (18:09 -0800)]
atm: nicstar: fix if-statement empty body warning
When debugging via PRINTK() is not enabled, make the PRINTK()
macro be an empty do-while block.
Thix fixes a gcc warning when -Wextra is set:
../drivers/atm/nicstar.c:1819:23: warning: suggest braces around empty body in an ‘else’ statement [-Wempty-body]
I have verified that there is no object code change (with gcc 7.5.0).
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Chas Williams <3chas3@gmail.com>
Cc: linux-atm-general@lists.sourceforge.net
Cc: netdev@vger.kernel.org
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso [Wed, 26 Feb 2020 18:47:34 +0000 (19:47 +0100)]
netlink: Use netlink header as base to calculate bad attribute offset
Userspace might send a batch that is composed of several netlink
messages. The netlink_ack() function must use the pointer to the netlink
header as base to calculate the bad attribute offset.
Fixes:
2d4bc93368f5 ("netlink: extended ACK reporting")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
You-Sheng Yang [Wed, 26 Feb 2020 15:37:10 +0000 (23:37 +0800)]
r8152: check disconnect status after long sleep
Dell USB Type C docking WD19/WD19DC attaches additional peripherals as:
/: Bus 02.Port 1: Dev 1, Class=root_hub, Driver=xhci_hcd/6p, 5000M
|__ Port 1: Dev 11, If 0, Class=Hub, Driver=hub/4p, 5000M
|__ Port 3: Dev 12, If 0, Class=Hub, Driver=hub/4p, 5000M
|__ Port 4: Dev 13, If 0, Class=Vendor Specific Class,
Driver=r8152, 5000M
where usb 2-1-3 is a hub connecting all USB Type-A/C ports on the dock.
When hotplugging such dock with additional usb devices already attached on
it, the probing process may reset usb 2.1 port, therefore r8152 ethernet
device is also reset. However, during r8152 device init there are several
for-loops that, when it's unable to retrieve hardware registers due to
being disconnected from USB, may take up to 14 seconds each in practice,
and that has to be completed before USB may re-enumerate devices on the
bus. As a result, devices attached to the dock will only be available
after nearly 1 minute after the dock was plugged in:
[ 216.388290] [250] r8152 2-1.4:1.0: usb_probe_interface
[ 216.388292] [250] r8152 2-1.4:1.0: usb_probe_interface - got id
[ 258.830410] r8152 2-1.4:1.0 (unnamed net_device) (uninitialized): PHY not ready
[ 258.830460] r8152 2-1.4:1.0 (unnamed net_device) (uninitialized): Invalid header when reading pass-thru MAC addr
[ 258.830464] r8152 2-1.4:1.0 (unnamed net_device) (uninitialized): Get ether addr fail
This happens in, for example, r8153_init:
static int generic_ocp_read(struct r8152 *tp, u16 index, u16 size,
void *data, u16 type)
{
if (test_bit(RTL8152_UNPLUG, &tp->flags))
return -ENODEV;
...
}
static u16 ocp_read_word(struct r8152 *tp, u16 type, u16 index)
{
u32 data;
...
generic_ocp_read(tp, index, sizeof(tmp), &tmp, type | byen);
data = __le32_to_cpu(tmp);
...
return (u16)data;
}
static void r8153_init(struct r8152 *tp)
{
...
if (test_bit(RTL8152_UNPLUG, &tp->flags))
return;
for (i = 0; i < 500; i++) {
if (ocp_read_word(tp, MCU_TYPE_PLA, PLA_BOOT_CTRL) &
AUTOLOAD_DONE)
break;
msleep(20);
}
...
}
Since ocp_read_word() doesn't check the return status of
generic_ocp_read(), and the only exit condition for the loop is to have
a match in the returned value, such loops will only ends after exceeding
its maximum runs when the device has been marked as disconnected, which
takes 500 * 20ms = 10 seconds in theory, 14 in practice.
To solve this long latency another test to RTL8152_UNPLUG flag should be
added after those 20ms sleep to skip unnecessary loops, so that the device
probe can complete early and proceed to parent port reset/reprobe process.
This can be reproduced on all kernel versions up to latest v5.6-rc2, but
after v5.5-rc7 the reproduce rate is dramatically lowered to 1/30 or less
while it was around 1/2.
Signed-off-by: You-Sheng Yang <vicamo.yang@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Fri, 28 Feb 2020 00:34:41 +0000 (16:34 -0800)]
Merge git://git./linux/kernel/git/netdev/net
Pull networking fixes from David Miller:
1) Fix leak in nl80211 AP start where we leak the ACL memory, from
Johannes Berg.
2) Fix double mutex unlock in mac80211, from Andrei Otcheretianski.
3) Fix RCU stall in ipset, from Jozsef Kadlecsik.
4) Fix devlink locking in devlink_dpipe_table_register, from Madhuparna
Bhowmik.
5) Fix race causing TX hang in ll_temac, from Esben Haabendal.
6) Stale eth hdr pointer in br_dev_xmit(), from Nikolay Aleksandrov.
7) Fix TX hash calculation bounds checking wrt. tc rules, from Amritha
Nambiar.
8) Size netlink responses properly in schedule action code to take into
consideration TCA_ACT_FLAGS. From Jiri Pirko.
9) Fix firmware paths for mscc PHY driver, from Antoine Tenart.
10) Don't register stmmac notifier multiple times, from Aaro Koskinen.
11) Various rmnet bug fixes, from Taehee Yoo.
12) Fix vsock deadlock in vsock transport release, from Stefano
Garzarella.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (61 commits)
net: dsa: mv88e6xxx: Fix masking of egress port
mlxsw: pci: Wait longer before accessing the device after reset
sfc: fix timestamp reconstruction at 16-bit rollover points
vsock: fix potential deadlock in transport->release()
unix: It's CONFIG_PROC_FS not CONFIG_PROCFS
net: rmnet: fix packet forwarding in rmnet bridge mode
net: rmnet: fix bridge mode bugs
net: rmnet: use upper/lower device infrastructure
net: rmnet: do not allow to change mux id if mux id is duplicated
net: rmnet: remove rcu_read_lock in rmnet_force_unassociate_device()
net: rmnet: fix suspicious RCU usage
net: rmnet: fix NULL pointer dereference in rmnet_changelink()
net: rmnet: fix NULL pointer dereference in rmnet_newlink()
net: phy: marvell: don't interpret PHY status unless resolved
mlx5: register lag notifier for init network namespace only
unix: define and set show_fdinfo only if procfs is enabled
hinic: fix a bug of rss configuration
hinic: fix a bug of setting hw_ioctxt
hinic: fix a irq affinity bug
net/smc: check for valid ib_client_data
...
Andrew Lunn [Thu, 27 Feb 2020 20:20:49 +0000 (21:20 +0100)]
net: dsa: mv88e6xxx: Fix masking of egress port
Add missing ~ to the usage of the mask.
Reported-by: Kevin Benson <Kevin.Benson@zii.aero>
Reported-by: Chris Healy <Chris.Healy@zii.aero>
Fixes:
5c74c54ce6ff ("net: dsa: mv88e6xxx: Split monitor port configuration")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Amit Cohen [Thu, 27 Feb 2020 20:07:53 +0000 (21:07 +0100)]
mlxsw: pci: Wait longer before accessing the device after reset
During initialization the driver issues a reset to the device and waits
for 100ms before checking if the firmware is ready. The waiting is
necessary because before that the device is irresponsive and the first
read can result in a completion timeout.
While 100ms is sufficient for Spectrum-1 and Spectrum-2, it is
insufficient for Spectrum-3.
Fix this by increasing the timeout to 200ms.
Fixes:
da382875c616 ("mlxsw: spectrum: Extend to support Spectrum-3 ASIC")
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alex Maftei (amaftei) [Wed, 26 Feb 2020 17:33:19 +0000 (17:33 +0000)]
sfc: fix timestamp reconstruction at 16-bit rollover points
We can't just use the top bits of the last sync event as they could be
off-by-one every 65,536 seconds, giving an error in reconstruction of
65,536 seconds.
This patch uses the difference in the bottom 16 bits (mod 2^16) to
calculate an offset that needs to be applied to the last sync event to
get to the current time.
Signed-off-by: Alexandru-Mihai Maftei <amaftei@solarflare.com>
Acked-by: Martin Habets <mhabets@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stefano Garzarella [Wed, 26 Feb 2020 10:58:18 +0000 (11:58 +0100)]
vsock: fix potential deadlock in transport->release()
Some transports (hyperv, virtio) acquire the sock lock during the
.release() callback.
In the vsock_stream_connect() we call vsock_assign_transport(); if
the socket was previously assigned to another transport, the
vsk->transport->release() is called, but the sock lock is already
held in the vsock_stream_connect(), causing a deadlock reported by
syzbot:
INFO: task syz-executor280:9768 blocked for more than 143 seconds.
Not tainted 5.6.0-rc1-syzkaller #0
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
syz-executor280 D27912 9768 9766 0x00000000
Call Trace:
context_switch kernel/sched/core.c:3386 [inline]
__schedule+0x934/0x1f90 kernel/sched/core.c:4082
schedule+0xdc/0x2b0 kernel/sched/core.c:4156
__lock_sock+0x165/0x290 net/core/sock.c:2413
lock_sock_nested+0xfe/0x120 net/core/sock.c:2938
virtio_transport_release+0xc4/0xd60 net/vmw_vsock/virtio_transport_common.c:832
vsock_assign_transport+0xf3/0x3b0 net/vmw_vsock/af_vsock.c:454
vsock_stream_connect+0x2b3/0xc70 net/vmw_vsock/af_vsock.c:1288
__sys_connect_file+0x161/0x1c0 net/socket.c:1857
__sys_connect+0x174/0x1b0 net/socket.c:1874
__do_sys_connect net/socket.c:1885 [inline]
__se_sys_connect net/socket.c:1882 [inline]
__x64_sys_connect+0x73/0xb0 net/socket.c:1882
do_syscall_64+0xfa/0x790 arch/x86/entry/common.c:294
entry_SYSCALL_64_after_hwframe+0x49/0xbe
To avoid this issue, this patch remove the lock acquiring in the
.release() callback of hyperv and virtio transports, and it holds
the lock when we call vsk->transport->release() in the vsock core.
Reported-by: syzbot+731710996d79d0d58fbc@syzkaller.appspotmail.com
Fixes:
408624af4c89 ("vsock: use local transport when it is loaded")
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 27 Feb 2020 19:52:35 +0000 (11:52 -0800)]
unix: It's CONFIG_PROC_FS not CONFIG_PROCFS
Fixes:
3a12500ed5dd ("unix: define and set show_fdinfo only if procfs is enabled")
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 27 Feb 2020 19:45:07 +0000 (11:45 -0800)]
Merge branch 'net-rmnet-fix-several-bugs'
Taehee Yoo says:
====================
net: rmnet: fix several bugs
This patchset is to fix several bugs in RMNET module.
1. The first patch fixes NULL-ptr-deref in rmnet_newlink().
When rmnet interface is being created, it uses IFLA_LINK
without checking NULL.
So, if userspace doesn't set IFLA_LINK, panic will occur.
In this patch, checking NULL pointer code is added.
2. The second patch fixes NULL-ptr-deref in rmnet_changelink().
To get real device in rmnet_changelink(), it uses IFLA_LINK.
But, IFLA_LINK should not be used in rmnet_changelink().
3. The third patch fixes suspicious RCU usage in rmnet_get_port().
rmnet_get_port() uses rcu_dereference_rtnl().
But, rmnet_get_port() is used by datapath.
So, rcu_dereference_bh() should be used instead of rcu_dereference_rtnl().
4. The fourth patch fixes suspicious RCU usage in
rmnet_force_unassociate_device().
RCU critical section should not be scheduled.
But, unregister_netdevice_queue() in the rmnet_force_unassociate_device()
would be scheduled.
So, the RCU warning occurs.
In this patch, the rcu_read_lock() in the rmnet_force_unassociate_device()
is removed because it's unnecessary.
5. The fifth patch fixes duplicate MUX ID case.
RMNET MUX ID is unique.
So, rmnet interface isn't allowed to be created, which have
a duplicate MUX ID.
But, only rmnet_newlink() checks this condition, rmnet_changelink()
doesn't check this.
So, duplicate MUX ID case would happen.
6. The sixth patch fixes upper/lower interface relationship problems.
When IFLA_LINK is used, the upper/lower infrastructure should be used.
Because it checks the maximum depth of upper/lower interfaces and it also
checks circular interface relationship, etc.
In this patch, netdev_upper_dev_link() is used.
7. The seventh patch fixes bridge related problems.
a) ->ndo_del_slave() doesn't work.
b) It couldn't detect circular upper/lower interface relationship.
c) It couldn't prevent stack overflow because of too deep depth
of upper/lower interface
d) It doesn't check the number of lower interfaces.
e) Panics because of several reasons.
These problems are actually the same problem.
So, this patch fixes these problems.
8. The eighth patch fixes packet forwarding issue in bridge mode
Packet forwarding is not working in rmnet bridge mode.
Because when a packet is forwarded, skb_push() for an ethernet header
is needed. But it doesn't call skb_push().
So, the ethernet header will be lost.
Change log:
- update commit logs.
- drop two patches in this patchset because of wrong target branch.
- ("net: rmnet: add missing module alias")
- ("net: rmnet: print error message when command fails")
- remove unneessary rcu_read_lock() in the third patch.
- use rcu_dereference_bh() instead of rcu_dereference in third patch.
- do not allow to add a bridge device if rmnet interface is already
bridge mode in the seventh patch.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Taehee Yoo [Thu, 27 Feb 2020 12:26:15 +0000 (12:26 +0000)]
net: rmnet: fix packet forwarding in rmnet bridge mode
Packet forwarding is not working in rmnet bridge mode.
Because when a packet is forwarded, skb_push() for an ethernet header
is needed. But it doesn't call skb_push().
So, the ethernet header will be lost.
Test commands:
modprobe rmnet
ip netns add nst
ip netns add nst2
ip link add veth0 type veth peer name veth1
ip link add veth2 type veth peer name veth3
ip link set veth1 netns nst
ip link set veth3 netns nst2
ip link add rmnet0 link veth0 type rmnet mux_id 1
ip link set veth2 master rmnet0
ip link set veth0 up
ip link set veth2 up
ip link set rmnet0 up
ip a a 192.168.100.1/24 dev rmnet0
ip netns exec nst ip link set veth1 up
ip netns exec nst ip a a 192.168.100.2/24 dev veth1
ip netns exec nst2 ip link set veth3 up
ip netns exec nst2 ip a a 192.168.100.3/24 dev veth3
ip netns exec nst2 ping 192.168.100.2
Fixes:
60d58f971c10 ("net: qualcomm: rmnet: Implement bridge mode")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Taehee Yoo [Thu, 27 Feb 2020 12:26:02 +0000 (12:26 +0000)]
net: rmnet: fix bridge mode bugs
In order to attach a bridge interface to the rmnet interface,
"master" operation is used.
(e.g. ip link set dummy1 master rmnet0)
But, in the rmnet_add_bridge(), which is a callback of ->ndo_add_slave()
doesn't register lower interface.
So, ->ndo_del_slave() doesn't work.
There are other problems too.
1. It couldn't detect circular upper/lower interface relationship.
2. It couldn't prevent stack overflow because of too deep depth
of upper/lower interface
3. It doesn't check the number of lower interfaces.
4. Panics because of several reasons.
The root problem of these issues is actually the same.
So, in this patch, these all problems will be fixed.
Test commands:
modprobe rmnet
ip link add dummy0 type dummy
ip link add rmnet0 link dummy0 type rmnet mux_id 1
ip link add dummy1 master rmnet0 type dummy
ip link add dummy2 master rmnet0 type dummy
ip link del rmnet0
ip link del dummy2
ip link del dummy1
Splat looks like:
[ 41.867595][ T1164] general protection fault, probably for non-canonical address 0xdffffc0000000101I
[ 41.869993][ T1164] KASAN: null-ptr-deref in range [0x0000000000000808-0x000000000000080f]
[ 41.872950][ T1164] CPU: 0 PID: 1164 Comm: ip Not tainted 5.6.0-rc1+ #447
[ 41.873915][ T1164] Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006
[ 41.875161][ T1164] RIP: 0010:rmnet_unregister_bridge.isra.6+0x71/0xf0 [rmnet]
[ 41.876178][ T1164] Code: 48 89 ef 48 89 c6 5b 5d e9 fc fe ff ff e8 f7 f3 ff ff 48 8d b8 08 08 00 00 48 ba 00 7
[ 41.878925][ T1164] RSP: 0018:
ffff8880c4d0f188 EFLAGS:
00010202
[ 41.879774][ T1164] RAX:
0000000000000000 RBX:
0000000000000000 RCX:
0000000000000101
[ 41.887689][ T1164] RDX:
dffffc0000000000 RSI:
ffffffffb8cf64f0 RDI:
0000000000000808
[ 41.888727][ T1164] RBP:
ffff8880c40e4000 R08:
ffffed101b3c0e3c R09:
0000000000000001
[ 41.889749][ T1164] R10:
0000000000000001 R11:
ffffed101b3c0e3b R12:
1ffff110189a1e3c
[ 41.890783][ T1164] R13:
ffff8880c4d0f200 R14:
ffffffffb8d56160 R15:
ffff8880ccc2c000
[ 41.891794][ T1164] FS:
00007f4300edc0c0(0000) GS:
ffff8880d9c00000(0000) knlGS:
0000000000000000
[ 41.892953][ T1164] CS: 0010 DS: 0000 ES: 0000 CR0:
0000000080050033
[ 41.893800][ T1164] CR2:
00007f43003bc8c0 CR3:
00000000ca53e001 CR4:
00000000000606f0
[ 41.894824][ T1164] Call Trace:
[ 41.895274][ T1164] ? rcu_is_watching+0x2c/0x80
[ 41.895895][ T1164] rmnet_config_notify_cb+0x1f7/0x590 [rmnet]
[ 41.896687][ T1164] ? rmnet_unregister_bridge.isra.6+0xf0/0xf0 [rmnet]
[ 41.897611][ T1164] ? rmnet_unregister_bridge.isra.6+0xf0/0xf0 [rmnet]
[ 41.898508][ T1164] ? __module_text_address+0x13/0x140
[ 41.899162][ T1164] notifier_call_chain+0x90/0x160
[ 41.899814][ T1164] rollback_registered_many+0x660/0xcf0
[ 41.900544][ T1164] ? netif_set_real_num_tx_queues+0x780/0x780
[ 41.901316][ T1164] ? __lock_acquire+0xdfe/0x3de0
[ 41.901958][ T1164] ? memset+0x1f/0x40
[ 41.902468][ T1164] ? __nla_validate_parse+0x98/0x1ab0
[ 41.903166][ T1164] unregister_netdevice_many.part.133+0x13/0x1b0
[ 41.903988][ T1164] rtnl_delete_link+0xbc/0x100
[ ... ]
Fixes:
60d58f971c10 ("net: qualcomm: rmnet: Implement bridge mode")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Taehee Yoo [Thu, 27 Feb 2020 12:25:43 +0000 (12:25 +0000)]
net: rmnet: use upper/lower device infrastructure
netdev_upper_dev_link() is useful to manage lower/upper interfaces.
And this function internally validates looping, maximum depth.
All or most virtual interfaces that could have a real interface
(e.g. macsec, macvlan, ipvlan etc.) use lower/upper infrastructure.
Test commands:
modprobe rmnet
ip link add dummy0 type dummy
ip link add rmnet1 link dummy0 type rmnet mux_id 1
for i in {2..100}
do
let A=$i-1
ip link add rmnet$i link rmnet$A type rmnet mux_id $i
done
ip link del dummy0
The purpose of the test commands is to make stack overflow.
Splat looks like:
[ 52.411438][ T1395] BUG: KASAN: slab-out-of-bounds in find_busiest_group+0x27e/0x2c00
[ 52.413218][ T1395] Write of size 64 at addr
ffff8880c774bde0 by task ip/1395
[ 52.414841][ T1395]
[ 52.430720][ T1395] CPU: 1 PID: 1395 Comm: ip Not tainted 5.6.0-rc1+ #447
[ 52.496511][ T1395] Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006
[ 52.513597][ T1395] Call Trace:
[ 52.546516][ T1395]
[ 52.558773][ T1395] Allocated by task
3171537984:
[ 52.588290][ T1395] BUG: unable to handle page fault for address:
ffffffffb999e260
[ 52.589311][ T1395] #PF: supervisor read access in kernel mode
[ 52.590529][ T1395] #PF: error_code(0x0000) - not-present page
[ 52.591374][ T1395] PGD
d6818067 P4D
d6818067 PUD
d6819063 PMD 0
[ 52.592288][ T1395] Thread overran stack, or stack corrupted
[ 52.604980][ T1395] Oops: 0000 [#1] SMP DEBUG_PAGEALLOC KASAN PTI
[ 52.605856][ T1395] CPU: 1 PID: 1395 Comm: ip Not tainted 5.6.0-rc1+ #447
[ 52.611764][ T1395] Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006
[ 52.621520][ T1395] RIP: 0010:stack_depot_fetch+0x10/0x30
[ 52.622296][ T1395] Code: ff e9 f9 fe ff ff 48 89 df e8 9c 1d 91 ff e9 ca fe ff ff cc cc cc cc cc cc cc 89 f8 0
[ 52.627887][ T1395] RSP: 0018:
ffff8880c774bb60 EFLAGS:
00010006
[ 52.628735][ T1395] RAX:
00000000001f8880 RBX:
ffff8880c774d140 RCX:
0000000000000000
[ 52.631773][ T1395] RDX:
000000000000001d RSI:
ffff8880c774bb68 RDI:
0000000000003ff0
[ 52.649584][ T1395] RBP:
ffffea00031dd200 R08:
ffffed101b43e403 R09:
ffffed101b43e403
[ 52.674857][ T1395] R10:
0000000000000001 R11:
ffffed101b43e402 R12:
ffff8880d900e5c0
[ 52.678257][ T1395] R13:
ffff8880c774c000 R14:
0000000000000000 R15:
dffffc0000000000
[ 52.694541][ T1395] FS:
00007fe867f6e0c0(0000) GS:
ffff8880da000000(0000) knlGS:
0000000000000000
[ 52.764039][ T1395] CS: 0010 DS: 0000 ES: 0000 CR0:
0000000080050033
[ 52.815008][ T1395] CR2:
ffffffffb999e260 CR3:
00000000c26aa005 CR4:
00000000000606e0
[ 52.862312][ T1395] Call Trace:
[ 52.887133][ T1395] Modules linked in: dummy rmnet veth openvswitch nsh nf_conncount nf_nat nf_conntrack nf_dex
[ 52.936749][ T1395] CR2:
ffffffffb999e260
[ 52.965695][ T1395] ---[ end trace
7e32ca99482dbb31 ]---
[ 52.966556][ T1395] RIP: 0010:stack_depot_fetch+0x10/0x30
[ 52.971083][ T1395] Code: ff e9 f9 fe ff ff 48 89 df e8 9c 1d 91 ff e9 ca fe ff ff cc cc cc cc cc cc cc 89 f8 0
[ 53.003650][ T1395] RSP: 0018:
ffff8880c774bb60 EFLAGS:
00010006
[ 53.043183][ T1395] RAX:
00000000001f8880 RBX:
ffff8880c774d140 RCX:
0000000000000000
[ 53.076480][ T1395] RDX:
000000000000001d RSI:
ffff8880c774bb68 RDI:
0000000000003ff0
[ 53.093858][ T1395] RBP:
ffffea00031dd200 R08:
ffffed101b43e403 R09:
ffffed101b43e403
[ 53.112795][ T1395] R10:
0000000000000001 R11:
ffffed101b43e402 R12:
ffff8880d900e5c0
[ 53.139837][ T1395] R13:
ffff8880c774c000 R14:
0000000000000000 R15:
dffffc0000000000
[ 53.141500][ T1395] FS:
00007fe867f6e0c0(0000) GS:
ffff8880da000000(0000) knlGS:
0000000000000000
[ 53.143343][ T1395] CS: 0010 DS: 0000 ES: 0000 CR0:
0000000080050033
[ 53.152007][ T1395] CR2:
ffffffffb999e260 CR3:
00000000c26aa005 CR4:
00000000000606e0
[ 53.156459][ T1395] Kernel panic - not syncing: Fatal exception
[ 54.213570][ T1395] Shutting down cpus with NMI
[ 54.354112][ T1395] Kernel Offset: 0x33000000 from 0xffffffff81000000 (relocation range: 0xffffffff80000000-0x)
[ 54.355687][ T1395] Rebooting in 5 seconds..
Fixes:
b37f78f234bf ("net: qualcomm: rmnet: Fix crash on real dev unregistration")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Taehee Yoo [Thu, 27 Feb 2020 12:25:19 +0000 (12:25 +0000)]
net: rmnet: do not allow to change mux id if mux id is duplicated
Basically, duplicate mux id isn't be allowed.
So, the creation of rmnet will be failed if there is duplicate mux id
is existing.
But, changelink routine doesn't check duplicate mux id.
Test commands:
modprobe rmnet
ip link add dummy0 type dummy
ip link add rmnet0 link dummy0 type rmnet mux_id 1
ip link add rmnet1 link dummy0 type rmnet mux_id 2
ip link set rmnet1 type rmnet mux_id 1
Fixes:
23790ef12082 ("net: qualcomm: rmnet: Allow to configure flags for existing devices")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Taehee Yoo [Thu, 27 Feb 2020 12:25:05 +0000 (12:25 +0000)]
net: rmnet: remove rcu_read_lock in rmnet_force_unassociate_device()
The notifier_call() of the slave interface removes rmnet interface with
unregister_netdevice_queue().
But, before calling unregister_netdevice_queue(), it acquires
rcu readlock.
In the RCU critical section, sleeping isn't be allowed.
But, unregister_netdevice_queue() internally calls synchronize_net(),
which would sleep.
So, suspicious RCU usage warning occurs.
Test commands:
modprobe rmnet
ip link add dummy0 type dummy
ip link add dummy1 type dummy
ip link add rmnet0 link dummy0 type rmnet mux_id 1
ip link set dummy1 master rmnet0
ip link del dummy0
Splat looks like:
[ 79.639245][ T1195] =============================
[ 79.640134][ T1195] WARNING: suspicious RCU usage
[ 79.640852][ T1195] 5.6.0-rc1+ #447 Not tainted
[ 79.641657][ T1195] -----------------------------
[ 79.642472][ T1195] ./include/linux/rcupdate.h:273 Illegal context switch in RCU read-side critical section!
[ 79.644043][ T1195]
[ 79.644043][ T1195] other info that might help us debug this:
[ 79.644043][ T1195]
[ 79.645682][ T1195]
[ 79.645682][ T1195] rcu_scheduler_active = 2, debug_locks = 1
[ 79.646980][ T1195] 2 locks held by ip/1195:
[ 79.647629][ T1195] #0:
ffffffffa3cf64f0 (rtnl_mutex){+.+.}, at: rtnetlink_rcv_msg+0x457/0x890
[ 79.649312][ T1195] #1:
ffffffffa39256c0 (rcu_read_lock){....}, at: rmnet_config_notify_cb+0xf0/0x590 [rmnet]
[ 79.651717][ T1195]
[ 79.651717][ T1195] stack backtrace:
[ 79.652650][ T1195] CPU: 3 PID: 1195 Comm: ip Not tainted 5.6.0-rc1+ #447
[ 79.653702][ T1195] Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006
[ 79.655037][ T1195] Call Trace:
[ 79.655560][ T1195] dump_stack+0x96/0xdb
[ 79.656252][ T1195] ___might_sleep+0x345/0x440
[ 79.656994][ T1195] synchronize_net+0x18/0x30
[ 79.661132][ T1195] netdev_rx_handler_unregister+0x40/0xb0
[ 79.666266][ T1195] rmnet_unregister_real_device+0x42/0xb0 [rmnet]
[ 79.667211][ T1195] rmnet_config_notify_cb+0x1f7/0x590 [rmnet]
[ 79.668121][ T1195] ? rmnet_unregister_bridge.isra.6+0xf0/0xf0 [rmnet]
[ 79.669166][ T1195] ? rmnet_unregister_bridge.isra.6+0xf0/0xf0 [rmnet]
[ 79.670286][ T1195] ? __module_text_address+0x13/0x140
[ 79.671139][ T1195] notifier_call_chain+0x90/0x160
[ 79.671973][ T1195] rollback_registered_many+0x660/0xcf0
[ 79.672893][ T1195] ? netif_set_real_num_tx_queues+0x780/0x780
[ 79.675091][ T1195] ? __lock_acquire+0xdfe/0x3de0
[ 79.675825][ T1195] ? memset+0x1f/0x40
[ 79.676367][ T1195] ? __nla_validate_parse+0x98/0x1ab0
[ 79.677290][ T1195] unregister_netdevice_many.part.133+0x13/0x1b0
[ 79.678163][ T1195] rtnl_delete_link+0xbc/0x100
[ ... ]
Fixes:
ceed73a2cf4a ("drivers: net: ethernet: qualcomm: rmnet: Initial implementation")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Taehee Yoo [Thu, 27 Feb 2020 12:24:45 +0000 (12:24 +0000)]
net: rmnet: fix suspicious RCU usage
rmnet_get_port() internally calls rcu_dereference_rtnl(),
which checks RTNL.
But rmnet_get_port() could be called by packet path.
The packet path is not protected by RTNL.
So, the suspicious RCU usage problem occurs.
Test commands:
modprobe rmnet
ip netns add nst
ip link add veth0 type veth peer name veth1
ip link set veth1 netns nst
ip link add rmnet0 link veth0 type rmnet mux_id 1
ip netns exec nst ip link add rmnet1 link veth1 type rmnet mux_id 1
ip netns exec nst ip link set veth1 up
ip netns exec nst ip link set rmnet1 up
ip netns exec nst ip a a 192.168.100.2/24 dev rmnet1
ip link set veth0 up
ip link set rmnet0 up
ip a a 192.168.100.1/24 dev rmnet0
ping 192.168.100.2
Splat looks like:
[ 146.630958][ T1174] WARNING: suspicious RCU usage
[ 146.631735][ T1174] 5.6.0-rc1+ #447 Not tainted
[ 146.632387][ T1174] -----------------------------
[ 146.633151][ T1174] drivers/net/ethernet/qualcomm/rmnet/rmnet_config.c:386 suspicious rcu_dereference_check() !
[ 146.634742][ T1174]
[ 146.634742][ T1174] other info that might help us debug this:
[ 146.634742][ T1174]
[ 146.645992][ T1174]
[ 146.645992][ T1174] rcu_scheduler_active = 2, debug_locks = 1
[ 146.646937][ T1174] 5 locks held by ping/1174:
[ 146.647609][ T1174] #0:
ffff8880c31dea70 (sk_lock-AF_INET){+.+.}, at: raw_sendmsg+0xab8/0x2980
[ 146.662463][ T1174] #1:
ffffffff93925660 (rcu_read_lock_bh){....}, at: ip_finish_output2+0x243/0x2150
[ 146.671696][ T1174] #2:
ffffffff93925660 (rcu_read_lock_bh){....}, at: __dev_queue_xmit+0x213/0x2940
[ 146.673064][ T1174] #3:
ffff8880c19ecd58 (&dev->qdisc_running_key#7){+...}, at: ip_finish_output2+0x714/0x2150
[ 146.690358][ T1174] #4:
ffff8880c5796898 (&dev->qdisc_xmit_lock_key#3){+.-.}, at: sch_direct_xmit+0x1e2/0x1020
[ 146.699875][ T1174]
[ 146.699875][ T1174] stack backtrace:
[ 146.701091][ T1174] CPU: 0 PID: 1174 Comm: ping Not tainted 5.6.0-rc1+ #447
[ 146.705215][ T1174] Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006
[ 146.706565][ T1174] Call Trace:
[ 146.707102][ T1174] dump_stack+0x96/0xdb
[ 146.708007][ T1174] rmnet_get_port.part.9+0x76/0x80 [rmnet]
[ 146.709233][ T1174] rmnet_egress_handler+0x107/0x420 [rmnet]
[ 146.710492][ T1174] ? sch_direct_xmit+0x1e2/0x1020
[ 146.716193][ T1174] rmnet_vnd_start_xmit+0x3d/0xa0 [rmnet]
[ 146.717012][ T1174] dev_hard_start_xmit+0x160/0x740
[ 146.717854][ T1174] sch_direct_xmit+0x265/0x1020
[ 146.718577][ T1174] ? register_lock_class+0x14d0/0x14d0
[ 146.719429][ T1174] ? dev_watchdog+0xac0/0xac0
[ 146.723738][ T1174] ? __dev_queue_xmit+0x15fd/0x2940
[ 146.724469][ T1174] ? lock_acquire+0x164/0x3b0
[ 146.725172][ T1174] __dev_queue_xmit+0x20c7/0x2940
[ ... ]
Fixes:
ceed73a2cf4a ("drivers: net: ethernet: qualcomm: rmnet: Initial implementation")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Taehee Yoo [Thu, 27 Feb 2020 12:24:26 +0000 (12:24 +0000)]
net: rmnet: fix NULL pointer dereference in rmnet_changelink()
In the rmnet_changelink(), it uses IFLA_LINK without checking
NULL pointer.
tb[IFLA_LINK] could be NULL pointer.
So, NULL-ptr-deref could occur.
rmnet already has a lower interface (real_dev).
So, after this patch, rmnet_changelink() does not use IFLA_LINK anymore.
Test commands:
modprobe rmnet
ip link add dummy0 type dummy
ip link add rmnet0 link dummy0 type rmnet mux_id 1
ip link set rmnet0 type rmnet mux_id 2
Splat looks like:
[ 90.578726][ T1131] general protection fault, probably for non-canonical address 0xdffffc0000000000I
[ 90.581121][ T1131] KASAN: null-ptr-deref in range [0x0000000000000000-0x0000000000000007]
[ 90.582380][ T1131] CPU: 2 PID: 1131 Comm: ip Not tainted 5.6.0-rc1+ #447
[ 90.584285][ T1131] Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006
[ 90.587506][ T1131] RIP: 0010:rmnet_changelink+0x5a/0x8a0 [rmnet]
[ 90.588546][ T1131] Code: 83 ec 20 48 c1 ea 03 80 3c 02 00 0f 85 6f 07 00 00 48 8b 5e 28 48 b8 00 00 00 00 00 0
[ 90.591447][ T1131] RSP: 0018:
ffff8880ce78f1b8 EFLAGS:
00010247
[ 90.592329][ T1131] RAX:
dffffc0000000000 RBX:
0000000000000000 RCX:
ffff8880ce78f8b0
[ 90.593253][ T1131] RDX:
0000000000000000 RSI:
ffff8880ce78f4a0 RDI:
0000000000000004
[ 90.594058][ T1131] RBP:
ffff8880cf543e00 R08:
0000000000000002 R09:
0000000000000002
[ 90.594859][ T1131] R10:
ffffffffc0586a40 R11:
0000000000000000 R12:
ffff8880ca47c000
[ 90.595690][ T1131] R13:
ffff8880ca47c000 R14:
ffff8880cf545000 R15:
0000000000000000
[ 90.596553][ T1131] FS:
00007f21f6c7e0c0(0000) GS:
ffff8880da400000(0000) knlGS:
0000000000000000
[ 90.597504][ T1131] CS: 0010 DS: 0000 ES: 0000 CR0:
0000000080050033
[ 90.599418][ T1131] CR2:
0000556e413db458 CR3:
00000000c917a002 CR4:
00000000000606e0
[ 90.600289][ T1131] Call Trace:
[ 90.600631][ T1131] __rtnl_newlink+0x922/0x1270
[ 90.601194][ T1131] ? lock_downgrade+0x6e0/0x6e0
[ 90.601724][ T1131] ? rtnl_link_unregister+0x220/0x220
[ 90.602309][ T1131] ? lock_acquire+0x164/0x3b0
[ 90.602784][ T1131] ? is_bpf_image_address+0xff/0x1d0
[ 90.603331][ T1131] ? rtnl_newlink+0x4c/0x90
[ 90.603810][ T1131] ? kernel_text_address+0x111/0x140
[ 90.604419][ T1131] ? __kernel_text_address+0xe/0x30
[ 90.604981][ T1131] ? unwind_get_return_address+0x5f/0xa0
[ 90.605616][ T1131] ? create_prof_cpu_mask+0x20/0x20
[ 90.606304][ T1131] ? arch_stack_walk+0x83/0xb0
[ 90.606985][ T1131] ? stack_trace_save+0x82/0xb0
[ 90.607656][ T1131] ? stack_trace_consume_entry+0x160/0x160
[ 90.608503][ T1131] ? deactivate_slab.isra.78+0x2c5/0x800
[ 90.609336][ T1131] ? kasan_unpoison_shadow+0x30/0x40
[ 90.610096][ T1131] ? kmem_cache_alloc_trace+0x135/0x350
[ 90.610889][ T1131] ? rtnl_newlink+0x4c/0x90
[ 90.611512][ T1131] rtnl_newlink+0x65/0x90
[ ... ]
Fixes:
23790ef12082 ("net: qualcomm: rmnet: Allow to configure flags for existing devices")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Taehee Yoo [Thu, 27 Feb 2020 12:23:52 +0000 (12:23 +0000)]
net: rmnet: fix NULL pointer dereference in rmnet_newlink()
rmnet registers IFLA_LINK interface as a lower interface.
But, IFLA_LINK could be NULL.
In the current code, rmnet doesn't check IFLA_LINK.
So, panic would occur.
Test commands:
modprobe rmnet
ip link add rmnet0 type rmnet mux_id 1
Splat looks like:
[ 36.826109][ T1115] general protection fault, probably for non-canonical address 0xdffffc0000000000I
[ 36.838817][ T1115] KASAN: null-ptr-deref in range [0x0000000000000000-0x0000000000000007]
[ 36.839908][ T1115] CPU: 1 PID: 1115 Comm: ip Not tainted 5.6.0-rc1+ #447
[ 36.840569][ T1115] Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006
[ 36.841408][ T1115] RIP: 0010:rmnet_newlink+0x54/0x510 [rmnet]
[ 36.841986][ T1115] Code: 83 ec 18 48 c1 e9 03 80 3c 01 00 0f 85 d4 03 00 00 48 8b 6a 28 48 b8 00 00 00 00 00 c
[ 36.843923][ T1115] RSP: 0018:
ffff8880b7e0f1c0 EFLAGS:
00010247
[ 36.844756][ T1115] RAX:
dffffc0000000000 RBX:
ffff8880d14cca00 RCX:
1ffff11016fc1e99
[ 36.845859][ T1115] RDX:
0000000000000000 RSI:
ffff8880c3d04000 RDI:
0000000000000004
[ 36.846961][ T1115] RBP:
0000000000000000 R08:
ffff8880b7e0f8b0 R09:
ffff8880b6ac2d90
[ 36.848020][ T1115] R10:
ffffffffc0589a40 R11:
ffffed1016d585b7 R12:
ffffffff88ceaf80
[ 36.848788][ T1115] R13:
ffff8880c3d04000 R14:
ffff8880b7e0f8b0 R15:
ffff8880c3d04000
[ 36.849546][ T1115] FS:
00007f50ab3360c0(0000) GS:
ffff8880da000000(0000) knlGS:
0000000000000000
[ 36.851784][ T1115] CS: 0010 DS: 0000 ES: 0000 CR0:
0000000080050033
[ 36.852422][ T1115] CR2:
000055871afe5ab0 CR3:
00000000ae246001 CR4:
00000000000606e0
[ 36.853181][ T1115] Call Trace:
[ 36.853514][ T1115] __rtnl_newlink+0xbdb/0x1270
[ 36.853967][ T1115] ? lock_downgrade+0x6e0/0x6e0
[ 36.854420][ T1115] ? rtnl_link_unregister+0x220/0x220
[ 36.854936][ T1115] ? lock_acquire+0x164/0x3b0
[ 36.855376][ T1115] ? is_bpf_image_address+0xff/0x1d0
[ 36.855884][ T1115] ? rtnl_newlink+0x4c/0x90
[ 36.856304][ T1115] ? kernel_text_address+0x111/0x140
[ 36.856857][ T1115] ? __kernel_text_address+0xe/0x30
[ 36.857440][ T1115] ? unwind_get_return_address+0x5f/0xa0
[ 36.858063][ T1115] ? create_prof_cpu_mask+0x20/0x20
[ 36.858644][ T1115] ? arch_stack_walk+0x83/0xb0
[ 36.859171][ T1115] ? stack_trace_save+0x82/0xb0
[ 36.859710][ T1115] ? stack_trace_consume_entry+0x160/0x160
[ 36.860357][ T1115] ? deactivate_slab.isra.78+0x2c5/0x800
[ 36.860928][ T1115] ? kasan_unpoison_shadow+0x30/0x40
[ 36.861520][ T1115] ? kmem_cache_alloc_trace+0x135/0x350
[ 36.862125][ T1115] ? rtnl_newlink+0x4c/0x90
[ 36.864073][ T1115] rtnl_newlink+0x65/0x90
[ ... ]
Fixes:
ceed73a2cf4a ("drivers: net: ethernet: qualcomm: rmnet: Initial implementation")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Thu, 27 Feb 2020 19:26:33 +0000 (11:26 -0800)]
Merge tag 'kbuild-fixes-v5.6-2' of git://git./linux/kernel/git/masahiroy/linux-kbuild
Pull Kbuild fixes from Masahiro Yamada:
- fix missed rebuild of DT schema check
- add some phony targets to PHONY
- fix comments and documents
* tag 'kbuild-fixes-v5.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
kbuild: get rid of trailing slash from subdir- example
kbuild: add dt_binding_check to PHONY in a correct place
kbuild: add dtbs_check to PHONY
kbuild: remove unneeded semicolon at the end of cmd_dtb_check
kbuild: fix DT binding schema rule to detect command line changes
kbuild: remove wrong documentation about mandatory-y
kbuild: add comment for V=2 mode
Russell King [Thu, 27 Feb 2020 09:44:49 +0000 (09:44 +0000)]
net: phy: marvell: don't interpret PHY status unless resolved
Don't attempt to interpret the PHY specific status register unless
the PHY is indicating that the resolution is valid.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko [Thu, 27 Feb 2020 07:22:10 +0000 (08:22 +0100)]
mlx5: register lag notifier for init network namespace only
The current code causes problems when the unregistering netdevice could
be different then the registering one.
Since the check in mlx5_lag_netdev_event() does not allow any other
network namespace anyway, fix this by registerting the lag notifier
per init network namespace only.
Fixes:
d48834f9d4b4 ("mlx5: Use dev_net netdevice notifier registrations")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Tested-by: Aya Levin <ayal@mellanox.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Thu, 27 Feb 2020 19:13:27 +0000 (11:13 -0800)]
Merge branch 'for-linus' of git://git./linux/kernel/git/hid/hid
Pull HID subsystem fixes from Jiri Kosina:
- syzkaller-reported error handling fixes in various drivers, from
various people
- increase of HID report buffer size to 8K, which is apparently needed
by certain modern devices
- a few new device-ID-specific fixes / quirks
- battery charging status reporting fix in logitech-hidpp, from Filipe
LaÃns
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid:
HID: hid-bigbenff: fix race condition for scheduled work during removal
HID: hid-bigbenff: call hid_hw_stop() in case of error
HID: hid-bigbenff: fix general protection fault caused by double kfree
HID: i2c-hid: add Trekstor Surfbook E11B to descriptor override
HID: alps: Fix an error handling path in 'alps_input_configured()'
HID: hiddev: Fix race in in hiddev_disconnect()
HID: core: increase HID report buffer size to 8KiB
HID: core: fix off-by-one memset in hid_report_raw_event()
HID: apple: Add support for recent firmware on Magic Keyboards
HID: ite: Only bind to keyboard USB interface on Acer SW5-012 keyboard dock
HID: logitech-hidpp: BatteryVoltage: only read chargeStatus if extPower is active
Tobias Klauser [Wed, 26 Feb 2020 17:29:53 +0000 (18:29 +0100)]
unix: define and set show_fdinfo only if procfs is enabled
Follow the pattern used with other *_show_fdinfo functions and only
define unix_show_fdinfo and set it in proto_ops if CONFIG_PROCFS
is set.
Fixes:
3c32da19a858 ("unix: Show number of pending scm files of receive queue in fdinfo")
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Reviewed-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 27 Feb 2020 19:08:01 +0000 (11:08 -0800)]
Merge branch 'hinic-BugFixes'
Luo bin says:
====================
hinic: BugFixes
the bug fixed in patch #2 has been present since the first commit.
the bugs fixed in patch #1 and patch #3 have been present since the
following commits:
patch #1:
352f58b0d9f2 ("net-next/hinic: Set Rxq irq to specific cpu for NUMA")
patch #3:
421e9526288b ("hinic: add rss support")
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Luo bin [Thu, 27 Feb 2020 06:34:44 +0000 (06:34 +0000)]
hinic: fix a bug of rss configuration
should use real receive queue number to configure hw rss
indirect table rather than maximal queue number
Signed-off-by: Luo bin <luobin9@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Luo bin [Thu, 27 Feb 2020 06:34:43 +0000 (06:34 +0000)]
hinic: fix a bug of setting hw_ioctxt
a reserved field is used to signify prime physical function index
in the latest firmware version, so we must assign a value to it
correctly
Signed-off-by: Luo bin <luobin9@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Luo bin [Thu, 27 Feb 2020 06:34:42 +0000 (06:34 +0000)]
hinic: fix a irq affinity bug
can not use a local variable as an input parameter of
irq_set_affinity_hint
Signed-off-by: Luo bin <luobin9@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Thu, 27 Feb 2020 19:07:13 +0000 (11:07 -0800)]
Merge tag 'docs-5.6-fixes' of git://git.lwn.net/linux
Pull documentation fixes from Jonathan Corbet:
"A pair of docs-build fixes"
* tag 'docs-5.6-fixes' of git://git.lwn.net/linux:
docs: Fix empty parallelism argument
docs: remove MPX from the x86 toc
Linus Torvalds [Thu, 27 Feb 2020 19:01:22 +0000 (11:01 -0800)]
Merge tag 'audit-pr-
20200226' of git://git./linux/kernel/git/pcmoore/audit
Pull audit fixes from Paul Moore:
"Two fixes for problems found by syzbot:
- Moving audit filter structure fields into a union caused some
problems in the code which populates that filter structure.
We keep the union (that idea is a good one), but we are fixing the
code so that it doesn't needlessly set fields in the union and mess
up the error handling.
- The audit_receive_msg() function wasn't validating user input as
well as it should in all cases, we add the necessary checks"
* tag 'audit-pr-
20200226' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/audit:
audit: always check the netlink payload length in audit_receive_msg()
audit: fix error handling in audit_data_to_entry()
Karsten Graul [Wed, 26 Feb 2020 16:52:46 +0000 (17:52 +0100)]
net/smc: check for valid ib_client_data
In smc_ib_remove_dev() check if the provided ib device was actually
initialized for SMC before.
Reported-by: syzbot+84484ccebdd4e5451d91@syzkaller.appspotmail.com
Fixes:
a4cf0443c414 ("smc: introduce SMC as an IB-client")
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Aaro Koskinen [Wed, 26 Feb 2020 16:49:01 +0000 (18:49 +0200)]
net: stmmac: fix notifier registration
We cannot register the same netdev notifier multiple times when probing
stmmac devices. Register the notifier only once in module init, and also
make debugfs creation/deletion safe against simultaneous notifier call.
Fixes:
481a7d154cbb ("stmmac: debugfs entry name is not be changed when udev rename device name.")
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Antoine Tenart [Wed, 26 Feb 2020 15:26:50 +0000 (16:26 +0100)]
net: phy: mscc: fix firmware paths
The firmware paths for the VSC8584 PHYs not not contain the leading
'microchip/' directory, as used in linux-firmware, resulting in an
error when probing the driver. This patch fixes it.
Fixes:
a5afc1678044 ("net: phy: mscc: add support for VSC8584 PHY")
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo Abeni [Wed, 26 Feb 2020 11:19:03 +0000 (12:19 +0100)]
mptcp: add dummy icsk_sync_mss()
syzbot noted that the master MPTCP socket lacks the icsk_sync_mss
callback, and was able to trigger a null pointer dereference:
BUG: kernel NULL pointer dereference, address:
0000000000000000
PGD
8e171067 P4D
8e171067 PUD
93fa2067 PMD 0
Oops: 0010 [#1] PREEMPT SMP KASAN
CPU: 0 PID: 8984 Comm: syz-executor066 Not tainted 5.6.0-rc2-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
RIP: 0010:0x0
Code: Bad RIP value.
RSP: 0018:
ffffc900020b7b80 EFLAGS:
00010246
RAX:
1ffff110124ba600 RBX:
0000000000000000 RCX:
ffff88809fefa600
RDX:
ffff8880994cdb18 RSI:
0000000000000000 RDI:
ffff8880925d3140
RBP:
ffffc900020b7bd8 R08:
ffffffff870225be R09:
fffffbfff140652a
R10:
fffffbfff140652a R11:
0000000000000000 R12:
ffff8880925d35d0
R13:
ffff8880925d3140 R14:
dffffc0000000000 R15:
1ffff110124ba6ba
FS:
0000000001a0b880(0000) GS:
ffff8880aea00000(0000) knlGS:
0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0:
0000000080050033
CR2:
ffffffffffffffd6 CR3:
00000000a6d6f000 CR4:
00000000001406f0
DR0:
0000000000000000 DR1:
0000000000000000 DR2:
0000000000000000
DR3:
0000000000000000 DR6:
00000000fffe0ff0 DR7:
0000000000000400
Call Trace:
cipso_v4_sock_setattr+0x34b/0x470 net/ipv4/cipso_ipv4.c:1888
netlbl_sock_setattr+0x2a7/0x310 net/netlabel/netlabel_kapi.c:989
smack_netlabel security/smack/smack_lsm.c:2425 [inline]
smack_inode_setsecurity+0x3da/0x4a0 security/smack/smack_lsm.c:2716
security_inode_setsecurity+0xb2/0x140 security/security.c:1364
__vfs_setxattr_noperm+0x16f/0x3e0 fs/xattr.c:197
vfs_setxattr fs/xattr.c:224 [inline]
setxattr+0x335/0x430 fs/xattr.c:451
__do_sys_fsetxattr fs/xattr.c:506 [inline]
__se_sys_fsetxattr+0x130/0x1b0 fs/xattr.c:495
__x64_sys_fsetxattr+0xbf/0xd0 fs/xattr.c:495
do_syscall_64+0xf7/0x1c0 arch/x86/entry/common.c:294
entry_SYSCALL_64_after_hwframe+0x49/0xbe
RIP: 0033:0x440199
Code: 18 89 d0 c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 0f 83 fb 13 fc ff c3 66 2e 0f 1f 84 00 00 00 00
RSP: 002b:
00007ffcadc19e48 EFLAGS:
00000246 ORIG_RAX:
00000000000000be
RAX:
ffffffffffffffda RBX:
00000000004002c8 RCX:
0000000000440199
RDX:
0000000020000200 RSI:
00000000200001c0 RDI:
0000000000000003
RBP:
00000000006ca018 R08:
0000000000000003 R09:
00000000004002c8
R10:
0000000000000009 R11:
0000000000000246 R12:
0000000000401a20
R13:
0000000000401ab0 R14:
0000000000000000 R15:
0000000000000000
Modules linked in:
CR2:
0000000000000000
Address the issue adding a dummy icsk_sync_mss callback.
To properly sync the subflows mss and options list we need some
additional infrastructure, which will land to net-next.
Reported-by: syzbot+f4dfece964792d80b139@syzkaller.appspotmail.com
Fixes:
2303f994b3e1 ("mptcp: Associate MPTCP context with TCP socket")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sudheesh Mavila [Wed, 26 Feb 2020 07:10:45 +0000 (12:40 +0530)]
net: phy: corrected the return value for genphy_check_and_restart_aneg and genphy_c45_check_and_restart_aneg
When auto-negotiation is not required, return value should be zero.
Changes v1->v2:
- improved comments and code as Andrew Lunn and Heiner Kallweit suggestion
- fixed issue in genphy_c45_check_and_restart_aneg as Russell King
suggestion.
Fixes:
2a10ab043ac5 ("net: phy: add genphy_check_and_restart_aneg()")
Fixes:
1af9f16840e9 ("net: phy: add genphy_c45_check_and_restart_aneg()")
Signed-off-by: Sudheesh Mavila <sudheesh.mavila@amd.com>
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
yangerkun [Wed, 26 Feb 2020 03:54:35 +0000 (11:54 +0800)]
slip: not call free_netdev before rtnl_unlock in slip_open
As the description before netdev_run_todo, we cannot call free_netdev
before rtnl_unlock, fix it by reorder the code.
Signed-off-by: yangerkun <yangerkun@huawei.com>
Reviewed-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Tue, 25 Feb 2020 19:52:29 +0000 (11:52 -0800)]
ipv6: restrict IPV6_ADDRFORM operation
IPV6_ADDRFORM is able to transform IPv6 socket to IPv4 one.
While this operation sounds illogical, we have to support it.
One of the things it does for TCP socket is to switch sk->sk_prot
to tcp_prot.
We now have other layers playing with sk->sk_prot, so we should make
sure to not interfere with them.
This patch makes sure sk_prot is the default pointer for TCP IPv6 socket.
syzbot reported :
BUG: kernel NULL pointer dereference, address:
0000000000000000
PGD
a0113067 P4D
a0113067 PUD
a8771067 PMD 0
Oops: 0010 [#1] PREEMPT SMP KASAN
CPU: 0 PID: 10686 Comm: syz-executor.0 Not tainted 5.6.0-rc2-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
RIP: 0010:0x0
Code: Bad RIP value.
RSP: 0018:
ffffc9000281fce0 EFLAGS:
00010246
RAX:
1ffffffff15f48ac RBX:
ffffffff8afa4560 RCX:
dffffc0000000000
RDX:
0000000000000000 RSI:
0000000000000000 RDI:
ffff8880a69a8f40
RBP:
ffffc9000281fd10 R08:
ffffffff86ed9b0c R09:
ffffed1014d351f5
R10:
ffffed1014d351f5 R11:
0000000000000000 R12:
ffff8880920d3098
R13:
1ffff1101241a613 R14:
ffff8880a69a8f40 R15:
0000000000000000
FS:
00007f2ae75db700(0000) GS:
ffff8880aea00000(0000) knlGS:
0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0:
0000000080050033
CR2:
ffffffffffffffd6 CR3:
00000000a3b85000 CR4:
00000000001406f0
DR0:
0000000000000000 DR1:
0000000000000000 DR2:
0000000000000000
DR3:
0000000000000000 DR6:
00000000fffe0ff0 DR7:
0000000000000400
Call Trace:
inet_release+0x165/0x1c0 net/ipv4/af_inet.c:427
__sock_release net/socket.c:605 [inline]
sock_close+0xe1/0x260 net/socket.c:1283
__fput+0x2e4/0x740 fs/file_table.c:280
____fput+0x15/0x20 fs/file_table.c:313
task_work_run+0x176/0x1b0 kernel/task_work.c:113
tracehook_notify_resume include/linux/tracehook.h:188 [inline]
exit_to_usermode_loop arch/x86/entry/common.c:164 [inline]
prepare_exit_to_usermode+0x480/0x5b0 arch/x86/entry/common.c:195
syscall_return_slowpath+0x113/0x4a0 arch/x86/entry/common.c:278
do_syscall_64+0x11f/0x1c0 arch/x86/entry/common.c:304
entry_SYSCALL_64_after_hwframe+0x49/0xbe
RIP: 0033:0x45c429
Code: ad b6 fb ff c3 66 2e 0f 1f 84 00 00 00 00 00 66 90 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 0f 83 7b b6 fb ff c3 66 2e 0f 1f 84 00 00 00 00
RSP: 002b:
00007f2ae75dac78 EFLAGS:
00000246 ORIG_RAX:
0000000000000036
RAX:
0000000000000000 RBX:
00007f2ae75db6d4 RCX:
000000000045c429
RDX:
0000000000000001 RSI:
000000000000011a RDI:
0000000000000004
RBP:
000000000076bf20 R08:
0000000000000038 R09:
0000000000000000
R10:
0000000020000180 R11:
0000000000000246 R12:
00000000ffffffff
R13:
0000000000000a9d R14:
00000000004ccfb4 R15:
000000000076bf2c
Modules linked in:
CR2:
0000000000000000
---[ end trace
82567b5207e87bae ]---
RIP: 0010:0x0
Code: Bad RIP value.
RSP: 0018:
ffffc9000281fce0 EFLAGS:
00010246
RAX:
1ffffffff15f48ac RBX:
ffffffff8afa4560 RCX:
dffffc0000000000
RDX:
0000000000000000 RSI:
0000000000000000 RDI:
ffff8880a69a8f40
RBP:
ffffc9000281fd10 R08:
ffffffff86ed9b0c R09:
ffffed1014d351f5
R10:
ffffed1014d351f5 R11:
0000000000000000 R12:
ffff8880920d3098
R13:
1ffff1101241a613 R14:
ffff8880a69a8f40 R15:
0000000000000000
FS:
00007f2ae75db700(0000) GS:
ffff8880aea00000(0000) knlGS:
0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0:
0000000080050033
CR2:
ffffffffffffffd6 CR3:
00000000a3b85000 CR4:
00000000001406f0
DR0:
0000000000000000 DR1:
0000000000000000 DR2:
0000000000000000
DR3:
0000000000000000 DR6:
00000000fffe0ff0 DR7:
0000000000000400
Fixes:
604326b41a6f ("bpf, sockmap: convert to generic sk_msg interface")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot+1938db17e275e85dc328@syzkaller.appspotmail.com
Cc: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ursula Braun [Tue, 25 Feb 2020 15:34:36 +0000 (16:34 +0100)]
net/smc: fix cleanup for linkgroup setup failures
If an SMC connection to a certain peer is setup the first time,
a new linkgroup is created. In case of setup failures, such a
linkgroup is unusable and should disappear. As a first step the
linkgroup is removed from the linkgroup list in smc_lgr_forget().
There are 2 problems:
smc_listen_decline() might be called before linkgroup creation
resulting in a crash due to calling smc_lgr_forget() with
parameter NULL.
If a setup failure occurs after linkgroup creation, the connection
is never unregistered from the linkgroup, preventing linkgroup
freeing.
This patch introduces an enhanced smc_lgr_cleanup_early() function
which
* contains a linkgroup check for early smc_listen_decline()
invocations
* invokes smc_conn_free() to guarantee unregistering of the
connection.
* schedules fast linkgroup removal of the unusable linkgroup
And the unused function smcd_conn_free() is removed from smc_core.h.
Fixes:
3b2dec2603d5b ("net/smc: restructure client and server code in af_smc")
Fixes:
2a0674fffb6bc ("net/smc: improve abnormal termination of link groups")
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nicolas Saenz Julienne [Tue, 25 Feb 2020 13:11:59 +0000 (14:11 +0100)]
net: bcmgenet: Clear ID_MODE_DIS in EXT_RGMII_OOB_CTRL when not needed
Outdated Raspberry Pi 4 firmware might configure the external PHY as
rgmii although the kernel currently sets it as rgmii-rxid. This makes
connections unreliable as ID_MODE_DIS is left enabled. To avoid this,
explicitly clear that bit whenever we don't need it.
Fixes:
da38802211cc ("net: bcmgenet: Add RGMII_RXID support")
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko [Tue, 25 Feb 2020 12:54:12 +0000 (13:54 +0100)]
sched: act: count in the size of action flags bitfield
The put of the flags was added by the commit referenced in fixes tag,
however the size of the message was not extended accordingly.
Fix this by adding size of the flags bitfield to the message size.
Fixes:
e38226786022 ("net: sched: update action implementations to support flags")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Masahiro Yamada [Wed, 26 Feb 2020 17:44:58 +0000 (02:44 +0900)]
kbuild: get rid of trailing slash from subdir- example
obj-* needs a trailing slash for a directory, but subdir-* does not.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Madhuparna Bhowmik [Tue, 25 Feb 2020 12:27:45 +0000 (17:57 +0530)]
net: core: devlink.c: Use built-in RCU list checking
list_for_each_entry_rcu() has built-in RCU and lock checking.
Pass cond argument to list_for_each_entry_rcu() to silence
false lockdep warning when CONFIG_PROVE_RCU_LIST is enabled.
The devlink->lock is held when devlink_dpipe_table_find()
is called in non RCU read side section. Therefore, pass struct devlink
to devlink_dpipe_table_find() for lockdep checking.
Signed-off-by: Madhuparna Bhowmik <madhuparnabhowmik10@gmail.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Mon, 24 Feb 2020 23:56:32 +0000 (15:56 -0800)]
net: dsa: bcm_sf2: Forcibly configure IMP port for 1Gb/sec
We are still experiencing some packet loss with the existing advanced
congestion buffering (ACB) settings with the IMP port configured for
2Gb/sec, so revert to conservative link speeds that do not produce
packet loss until this is resolved.
Fixes:
8f1880cbe8d0 ("net: dsa: bcm_sf2: Configure IMP port for 2Gb/sec")
Fixes:
de34d7084edd ("net: dsa: bcm_sf2: Only 7278 supports 2Gb/sec IMP port")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 27 Feb 2020 00:30:17 +0000 (16:30 -0800)]
Merge git://git./pub/scm/linux/kernel/git/pablo/nf
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes:
1) Perform garbage collection from workqueue to fix rcu detected
stall in ipset hash set types, from Jozsef Kadlecsik.
2) Fix the forceadd evaluation path, also from Jozsef.
3) Fix nft_set_pipapo selftest, from Stefano Brivio.
4) Crash when add-flush-add element in pipapo set, also from Stefano.
Add test to cover this crash.
5) Remove sysctl entry under mutex in hashlimit, from Cong Wang.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Wed, 26 Feb 2020 23:54:52 +0000 (15:54 -0800)]
Merge tag 'tag-chrome-platform-fixes-for-v5.6-rc4' of git://git./linux/kernel/git/chrome-platform/linux
Pull chrome platform fix from Benson Leung:
"Fix a build warning"
* tag 'tag-chrome-platform-fixes-for-v5.6-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/chrome-platform/linux:
platform/chrome: wilco_ec: Include asm/unaligned instead of linux/ path