Arnd Bergmann [Mon, 11 Jul 2016 20:49:53 +0000 (22:49 +0200)]
iwlwifi: add missing type declaration
The iwl-debug.h header relies in implicit inclusion of linux/device.h and
we get a lot of warnings without that:
drivers/net/wireless/intel/iwlwifi/iwl-debug.h:44:23: error: 'struct device' declared inside parameter list will not be visible outside of this definition or declaration [-Werror]
void __iwl_err(struct device *dev, bool rfkill_prefix, bool only_trace,
^~~~~~
In file included from drivers/net/wireless/intel/iwlwifi/iwl-eeprom-read.h:66:0,
from drivers/net/wireless/intel/iwlwifi/iwl-eeprom-read.c:68:
drivers/net/wireless/intel/iwlwifi/iwl-trans.h: In function 'iwl_trans_tx':
drivers/net/wireless/intel/iwlwifi/iwl-trans.h:1030:348: error: passing argument 1 of '__iwl_err' from incompatible pointer type [-Werror=incompatible-pointer-types]
IWL_ERR(trans, "%s bad state = %d\n", __func__, trans->state);
^
In file included from drivers/net/wireless/intel/iwlwifi/iwl-eeprom-read.c:67:0:
drivers/net/wireless/intel/iwlwifi/iwl-debug.h:44:6: note: expected 'struct device *' but argument is of type 'struct device *'
void __iwl_err(struct device *dev, bool rfkill_prefix, bool only_trace,
^~~~~~~~~
The easiest workaround is to just declare 'struct device' before its first use,
rather than including the entire header file.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes:
21cb3222fe56 ("iwlwifi: decouple PCIe transport from mac80211")
Acked-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Kalle Valo [Sun, 10 Jul 2016 18:02:20 +0000 (21:02 +0300)]
Merge git://git./linux/kernel/git/kvalo/wireless-drivers.git
This is to fix some conflicts in iwlwifi.
Conflicts:
drivers/net/wireless/intel/iwlwifi/mvm/mac80211.c
drivers/net/wireless/intel/iwlwifi/mvm/scan.c
Larry Finger [Tue, 5 Jul 2016 15:08:15 +0000 (10:08 -0500)]
rtlwifi: rtl8723ae: Clean up the hardware info routine
This driver contains some complicated if ... else if ... else constructions.
These are replaced by switch statements to improve readability.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Larry Finger [Tue, 5 Jul 2016 15:08:14 +0000 (10:08 -0500)]
rtlwifi: rtl8192de: Convert driver to use common hardware info routine
The driver for RTL8192DE chips is converted to use the common routine
for getting the hardware information.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Larry Finger [Tue, 5 Jul 2016 15:08:13 +0000 (10:08 -0500)]
rtlwifi: rtl8821ae: Convert driver to use common hardware info routine
The driver for RTL8821AE chips is converted to use the common routine
for getting the hardware information.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Larry Finger [Tue, 5 Jul 2016 15:08:12 +0000 (10:08 -0500)]
rtlwifi: rtl8723be: Convert driver to use common hardware info routine
The driver for RTL8723BE chips is converted to use the common routine
for getting the hardware information.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Larry Finger [Tue, 5 Jul 2016 15:08:11 +0000 (10:08 -0500)]
rtlwifi: rtl8723ae: Convert driver to use common hardware info routine
The driver for RTL8723AE chips is converted to use the common routine
for getting the hardware information.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Larry Finger [Tue, 5 Jul 2016 15:08:10 +0000 (10:08 -0500)]
rtlwifi: rtl8192ee: Convert driver to use common hardware info routine
The driver for RTL8192EE chips is converted to use the common routine
for getting the hardware information.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Larry Finger [Tue, 5 Jul 2016 15:08:09 +0000 (10:08 -0500)]
rtlwifi: rtl8188ee: Convert driver to use common hardware info routine
The driver for RTL8188EE chips is converted to use the common routine
for getting the hardware information.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Larry Finger [Tue, 5 Jul 2016 15:08:08 +0000 (10:08 -0500)]
rtlwifi: rtl8192cu: Convert driver to use common hardware info routine
The driver for RTL8192CU chips is converted to use the common routine
for getting the hardware information.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Larry Finger [Tue, 5 Jul 2016 15:08:07 +0000 (10:08 -0500)]
rtlwifi: rtl8192ce: Convert driver to use common hardware info routine
The driver for RTL8192CE chips is converted to use the common routine
for getting the hardware information.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Larry Finger [Tue, 5 Jul 2016 15:08:06 +0000 (10:08 -0500)]
rtlwifi: Create common routine to get hardware info
All of the rtlwifi family of drivers have a similar routine that acquires
the hardware info from efuse and initializes a number of variables in the
driver's private area. A common routine is created for all drivers to use.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Shengzhen Li [Fri, 1 Jul 2016 12:56:52 +0000 (18:26 +0530)]
mwifiex: fix interrupt processing corner case in MSI mode
As interrupt is read in interrupt handler as well as interrupt processing
thread, we observed a corner case issue for MSI in which interrupt gets
processed twice.
This patch moves interrupt reading code for MSI mode from
mwifiex_interrupt_status() to mwifiex_pcie_process_int() to avoid the
issue.
Signed-off-by: Shengzhen Li <szli@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Brian Norris [Thu, 30 Jun 2016 22:21:02 +0000 (15:21 -0700)]
mwifiex: mask PCIe interrupts before removal
The PCIe driver didn't mask the host interrupts before trying to tear
down. This causes lockups at reboot or rmmod when using MSI-X on 8997,
since the MSI handler gets confused and locks up the system.
Also tested on 8897, which does not support MSI-X (and wasn't
experiencing this same bug). No regressions seen there.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Amitkumar Karwar [Thu, 30 Jun 2016 16:54:57 +0000 (22:24 +0530)]
mwifiex: Change default firmware for PCIe8997 chipset
PCIe-USB8997 variant is being used in the product. Let's change default
firmware from PCIe-UART to PCIe-USB. So by default PCIe-USB firmware would
be downloaded if version register doesn't give any information.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Prasun Maiti [Thu, 30 Jun 2016 08:31:23 +0000 (14:01 +0530)]
mwifiex: Fix endianness for event TLV type TLV_BTCOEX_WL_SCANTIME
The two members min_scan_time and max_scan_time of structure
"mwifiex_ie_types_btcoex_scan_time" are of two bytes each. The values
are assigned directtly from firmware without endian conversion handling.
So, wrong datas will get saved in big-endian systems.
This patch converts the values into cpu's byte order before assigning them
into the local members.
Signed-off-by: Prasun Maiti <prasunmaiti87@gmail.com>
Acked-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Rafał Miłecki [Wed, 29 Jun 2016 19:54:27 +0000 (21:54 +0200)]
brcmfmac: support removing AP interfaces with "interface_remove"
New firmwares (e.g. 10.10.69.36 for BCM4366) support "interface_remove"
for removing interfaces. Try to use this method on cfg80211 request. In
case of older firmwares (e.g. 7.35.177.56 for BCM43602 as I tested) this
will just result in firmware rejecting command and this won't change any
behavior.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Rafał Miłecki [Wed, 29 Jun 2016 19:54:26 +0000 (21:54 +0200)]
brcmfmac: delete interface directly in code that sent fw request
So far when receiving event about in-firmware-interface removal our
event worker was notifying listener and afterwards it was removing Linux
interface.
First of all it was resulting in slightly unexpected order. The listener
(del_virtual_intf callback) was (usually) returning with success before
we even called unregister_netdev(ice).
Please note this couldn't be simply fixed by changing order of calls in
brcmf_fweh_handle_if_event as unregistering interface earlier could free
struct brcmf_if.
Another problem of current implementation are possible lockups. Focus on
the time slot between calling event handler and removing Linux
interface. During that time original caller may leave (unlocking rtnl
semaphore) *and* another call to the same code may be done (locking it
again). If that happens our event handler will stuck at removing Linux
interface, it won't handle another event and will block process holding
rtnl lock.
This can be simply solved by unregistering interface in a proper
callback, right after receiving confirmation event from firmware. This
only required modifying worker to don't unregister on its own if there
is someone waiting for the event.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Amitkumar Karwar [Wed, 29 Jun 2016 12:02:40 +0000 (17:32 +0530)]
mwifiex: fix scan_block flag handling
scan_block flag is used to block scan operation when 4 way handshake
is in progress. Sometimes it doesn't get cleared due to incomplete
association. An example is assoc request/response is done, but add key
operation get canceled in some corner cases. As a result, further
association/scan operations are blocked.
This patch fixes the problem by clearing scan_block flag.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Masanari Iida [Wed, 29 Jun 2016 03:37:19 +0000 (12:37 +0900)]
rtlwifi: Fix typo in printk
This patch fix spelling typos found in drivers/net/wireless/realtek.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Reviewed-by: Julian Calaby <julian.calaby@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Jes Sorensen [Mon, 27 Jun 2016 16:32:10 +0000 (12:32 -0400)]
rtl8xxxu: gen1: Add module parameters to adjust DMA aggregation parameters
This allows the user to specify DMA aggregation timout and block
count. Blocks are presumably always 512 bytes, so the minimum block
count is 6 for 802.11 packets.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Jes Sorensen [Mon, 27 Jun 2016 16:32:09 +0000 (12:32 -0400)]
rtl8xxxu: gen1: Set aggregation timeout (REG_RXDMA_AGG_PG_TH + 1) as well
gen2 chips as well as 8188eu seems to use this register for setting
DMA timeout threshold values, however the 8192cu is using
REG_USB_DMA_AGG_TO. Set both to be on the safe side.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Jes Sorensen [Mon, 27 Jun 2016 16:32:08 +0000 (12:32 -0400)]
rtl8xxxu: Make DMA aggregation optional by setting a module parameter
Let the default to off until we have more data on the right default
tuning values.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Jes Sorensen [Mon, 27 Jun 2016 16:32:07 +0000 (12:32 -0400)]
rtl8xxxu: Enable aggregation for rtl8192cu/rtl8188cu/rtl8188ru
This enables aggregation on rtl8192cu and derivative parts. This uses
the same parameters as for rtl8723au.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Jes Sorensen [Mon, 27 Jun 2016 16:32:06 +0000 (12:32 -0400)]
rtl8xxxu: Enable aggregation for rtl8723au
Implement rtl8xxxu_gen1_init_aggregation(). Aggregation should be the
same for all gen1 parts. We may want to allow for tuning parameters in
the fileopes struct. For now this is based allocating 16KB RX buffers,
leaving 16000 bytes for actual packets, and the rest for the skb
overhead.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Jes Sorensen [Mon, 27 Jun 2016 16:32:05 +0000 (12:32 -0400)]
rtl8xxxu: Adjust RX skb size to include space for phystats
The old allocation didn't leave space for phystats in the buffer,
allowing the packet to be rejected if a frame size of size
IEEE80211_MAX_FRAME_LEN was received.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Jes Sorensen [Mon, 27 Jun 2016 16:32:04 +0000 (12:32 -0400)]
rtl8xxxu: Allocate larger RX skbs when aggregation is enabled
This adds support for allocating larger skbs for devices which
indicate they support it.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Jes Sorensen [Mon, 27 Jun 2016 16:32:03 +0000 (12:32 -0400)]
rtl8xxxu: Add support for aggregated RX packets on gen1 parts
This implements support for demuxing aggregated RX packets on gen1
devices, using the rxdesc16 format.
So far this has only been tested with rtl8723au devices.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Jes Sorensen [Mon, 27 Jun 2016 16:32:02 +0000 (12:32 -0400)]
rtl8xxxu: Correct rxdesc16 definition
This corrects the definition of rxdesc16 to correctly specify pkt_cnt
for aggregated packets. This is based on the code of the vendor
rtl8723au driver, as opposed to the struct definitions they use.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Jes Sorensen [Mon, 27 Jun 2016 16:32:01 +0000 (12:32 -0400)]
rtl8xxxu: Obtain ieee80211_rx_status within parse_rx_desc()
When handling aggregated packets, we'll get a new ieee80211_rx_status
for each cloned skb, so passing in the pointer from the outside
doesn't make sense.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Jes Sorensen [Mon, 27 Jun 2016 16:32:00 +0000 (12:32 -0400)]
rtl8xxxu: Move skb delivery into parse_tx_desc() handler
This is another prepatory patch to be able to handle aggregated RX
packets.
In order to avoid adding a prototype, this also moves the
rtl8723bu_handle_c2h() function.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Jes Sorensen [Mon, 27 Jun 2016 16:31:59 +0000 (12:31 -0400)]
rtl8xxxu: Set all ieee80211_rx_status values in parse_rx_desc()
This needs to be handled locally in the parse_rx_desc() function in
order to be able to handle aggregated packets in the future.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Machani, Yaniv [Mon, 27 Jun 2016 13:37:14 +0000 (16:37 +0300)]
wlcore: time sync : add support for 64 bit clock
Changed the configuration to support 64bit instead of 32bit
this in order to offload the driver from handling a wraparound.
Signed-off-by: Yaniv Machani <yanivma@ti.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Amitkumar Karwar [Mon, 27 Jun 2016 08:46:29 +0000 (14:16 +0530)]
mwifiex: fix NULL pointer dereference during suspend
This patch fixes below NULL pointer dereference observed in suspend
stress test. When scan is cancelled during system suspend, we may end
up aceesing "priv->scan_request" in corner case.
[ 3035.304682] BUG: KASAN: null-ptr-deref on address
0000000000000008
[ 3035.304704] Read of size 4 by task ksdioirqd/mmc2/1183
[ 3035.304744] CPU: 0 PID: 1183 Comm: ksdioirqd/mmc2 Tainted: G W 3.18.0 #1169
[ 3035.304772] Call trace:
[ 3035.304825] [<
ffffffc00020a520>] dump_backtrace+0x0/0x190
[ 3035.304864] [<
ffffffc00020a6cc>] show_stack+0x1c/0x28
[ 3035.304901] [<
ffffffc000b36db8>] dump_stack+0xa0/0xf8
[ 3035.304940] [<
ffffffc00039c494>] kasan_report+0x120/0x4fc
[ 3035.304975] [<
ffffffc00039b6b4>] __asan_load4+0x20/0x80
[ 3035.305546] [<
ffffffbffc1f5aec>] mwifiex_check_next_scan_command+0x1a4/0x588 [mwifiex]
[ 3035.306091] [<
ffffffbffc1f7aec>] mwifiex_handle_event_ext_scan_report+0x304/0x370 [mwifiex]
[ 3035.306735] [<
ffffffbffc206bb8>] mwifiex_process_sta_event+0x6c0/0xf10 [mwifiex]
[ 3035.307200] [<
ffffffbffc1e609c>] mwifiex_process_event+0x2f4/0x358 [mwifiex]
[ 3035.307612] [<
ffffffbffc1e25c8>] mwifiex_main_process+0x3cc/0x80c [mwifiex]
[ 3035.307737] [<
ffffffbffc2523a0>] mwifiex_sdio_interrupt+0x198/0x1c0 [mwifiex_sdio]
[ 3035.307785] [<
ffffffc0008d9250>] process_sdio_pending_irqs+0x15c/0x1d4
[ 3035.307826] [<
ffffffc0008d93f0>] sdio_irq_thread+0xd8/0x288
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Amitkumar Karwar [Mon, 27 Jun 2016 08:46:28 +0000 (14:16 +0530)]
mwifiex: clear scan_aborting flag
The flag should be cleaned along with other scan operation variables.
This was missing at some places.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Amitkumar Karwar [Mon, 27 Jun 2016 08:46:27 +0000 (14:16 +0530)]
mwifiex: code rearrangement in suspend handler
We will derive sta_priv at the beginning of suspend handler.
This will be useful for next patch in this series.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Joe Perches [Sun, 26 Jun 2016 19:34:30 +0000 (12:34 -0700)]
rtlwifi: Add missing newlines to RT_TRACE calls
RT_TRACE does not add a newline to the end of a message and always
emits at KERN_DEBUG so these are susceptible to message interleaving
from other processes without the newline.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Joe Perches [Sat, 25 Jun 2016 22:46:45 +0000 (15:46 -0700)]
rtlwifi: Create _rtl_dbg_trace function to reduce RT_TRACE code size
This debugging macro can expand to a lot of code.
Make it a function to reduce code size.
(x86-64 defconfig w/ all rtlwifi drivers and allyesconfig)
$ size drivers/net/wireless/realtek/rtlwifi/built-in.o*
text data bss dec hex filename
900083 200499 1907 1102489 10d299 drivers/net/wireless/realtek/rtlwifi/built-in.o.defconfig.new
1113597 200499 1907 1316003 1414a3 drivers/net/wireless/realtek/rtlwifi/built-in.o.defconfig.old
1746879 453503 8512 2208894 21b47e drivers/net/wireless/realtek/rtlwifi/built-in.o.new
2051965 503311 8512 2563788 271ecc drivers/net/wireless/realtek/rtlwifi/built-in.o.old
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Jes Sorensen [Thu, 23 Jun 2016 18:35:53 +0000 (14:35 -0400)]
rtl8xxxu: Reduce console noise when removing the kernel module
USB urbs will return with a status != 0 when rmmod'ing the driver. No
need to fill the log with messages from rtl8xxxu_int_complete()
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Luis de Bethencourt [Thu, 23 Jun 2016 18:35:52 +0000 (14:35 -0400)]
rtl8xxxu: remove unneeded assignments
reg_eac and reg_ecc are only used if candidate is bigger than 0, and in
that case new values will be given to them. Removing the unused
assignments.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Kalle Valo [Fri, 8 Jul 2016 09:20:30 +0000 (12:20 +0300)]
Merge tag 'iwlwifi-next-for-kalle-2016-07-06' of git://git./linux/kernel/git/iwlwifi/iwlwifi-next
* work on DQA continued
* SAR BIOS implementation
* some work on debugging capabilities
* added support for GCMP encryption
* data path rework in preparation for new HW
* some cleanup to remove transport dependency on mac80211
* support for MSIx in preparation for new HW
* lots of work in preparation for HW support (9000 and a000 series)
* general cleanups
* general bugfixes
Sara Sharon [Tue, 5 Jul 2016 15:50:17 +0000 (18:50 +0300)]
iwlwifi: move iwl_drv to be shared across transports
All transports has this structure. By moving it to be
shared, we can get rid of casting to the specific transport
in probe and remove.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Sara Sharon [Thu, 30 Jun 2016 08:48:30 +0000 (11:48 +0300)]
iwlwifi: pcie: centralize SCD status logging
Centralize the logging of SCD status. The motivation is
that for a000 devices we will have new SCD HW, but this
code was duplicate anyway, so it is a proper cleanup.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Luca Coelho [Tue, 28 Jun 2016 21:38:40 +0000 (00:38 +0300)]
iwlwifi: mvm: support v4 of the TX power command
Add support for the v4 version of the TX power command. Just add a
new version and do the same sizing tricks that were done when support
for v3 was introduced.
This patch doesn't support the new functionality introduced, but makes
the driver work with the new size of the command.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Sara Sharon [Wed, 22 Jun 2016 16:25:46 +0000 (19:25 +0300)]
iwlwifi: pcie: load FW chunk for a000 devices
Update the firmware load flow for TFH hardware.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Sara Sharon [Wed, 22 Jun 2016 14:23:34 +0000 (17:23 +0300)]
iwlwifi: pcie: initialize a000 device's TFD table
For a000 device the FH was replaced by the TFH.
This is the first patch in a series introducing the
changes stemming from this change.
This patch initializes the TFQ queue table with the new
64 bit register and the relevant TFH configuration
registers.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Sara Sharon [Thu, 23 Jun 2016 09:04:55 +0000 (12:04 +0300)]
iwlwifi: centralize 64 bit HW registers write
Move the write_prph_64 of pcie to be transport agnostic.
Add direct write as well, as it is needed for a000 HW.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Sara Sharon [Thu, 9 Jun 2016 14:56:38 +0000 (17:56 +0300)]
iwlwifi: pcie: generalize and increase the size of scratchbuf
Currently the scratch buffer is set to 16 bytes and indicates
the size of the bi-directional DMA.
However, next HW generation will perform additional offloading,
and will write the result in the key location of the TX command,
so the size of the bi-directional consistent memory should grow
accordingly - increase it to 40.
Generalize the code to get rid of now irrelevant scratch references.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Sara Sharon [Tue, 21 Jun 2016 09:44:01 +0000 (12:44 +0300)]
iwlwifi: pcie: track rxb status
In MQ environment and new architecture in early stages
we may encounter DMA issues. Track RXB status and bail
out in case we receive index to an RXB that was not
mapped and handed over to HW.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Emmanuel Grumbach [Mon, 13 Jun 2016 05:28:26 +0000 (08:28 +0300)]
iwlwifi: pcie: fix a race in firmware loading flow
Upon firmware load interrupt (FH_TX), the ISR re-enables the
firmware load interrupt only to avoid races with other
flows as described in the commit below. When the firmware
is completely loaded, the thread that is loading the
firmware will enable all the interrupts to make sure that
the driver gets the ALIVE interrupt.
The problem with that is that the thread that is loading
the firmware is actually racing against the ISR and we can
get to the following situation:
CPU0 CPU1
iwl_pcie_load_given_ucode
...
iwl_pcie_load_firmware_chunk
wait_for_interrupt
<interrupt>
ISR handles CSR_INT_BIT_FH_TX
ISR wakes up the thread on CPU0
/* enable all the interrupts
* to get the ALIVE interrupt
*/
iwl_enable_interrupts
ISR re-enables CSR_INT_BIT_FH_TX only
/* start the firmware */
iwl_write32(trans, CSR_RESET, 0);
BUG! ALIVE interrupt will never arrive since it has been
masked by CPU1.
In order to fix that, change the ISR to first check if
STATUS_INT_ENABLED is set. If so, re-enable all the
interrupts. If STATUS_INT_ENABLED is clear, then we can
check what specific interrupt happened and re-enable only
that specific interrupt (RFKILL or FH_TX).
All the credit for the analysis goes to Kirtika who did the
actual debugging work.
Cc: <stable@vger.kernel.org> [4.5+]
Fixes:
a6bd005fe92 ("iwlwifi: pcie: fix RF-Kill vs. firmware load race")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Johannes Berg [Tue, 21 Jun 2016 11:11:48 +0000 (13:11 +0200)]
iwlwifi: decouple PCIe transport from mac80211
The PCIe transport needs to store two pointers in each TX SKB, and
currently assumes mac80211's ieee80211_tx_info is present in the CB
to do that.
In order to remove that assumption, have the opmodes pass in the
offset to where the pointers can be stored in the CB and use the
offset in the PCIe code.
To make the disentanglement complete, remove mac80211.h includes
from everywhere in the generic iwlwifi code. This required adding
an include of cfg80211.h in one place.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Johannes Berg [Tue, 21 Jun 2016 10:44:21 +0000 (12:44 +0200)]
iwlwifi: tracing: decouple from mac80211
In order to be able to properly record SKBs that didn't come through
mac80211, don't rely on the IEEE80211_TX_CTRL_PORT_CTRL_PROTO flag
but instead check for ETH_P_PAE directly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Johannes Berg [Tue, 21 Jun 2016 10:34:36 +0000 (12:34 +0200)]
iwlwifi: store cipher scheme independent of mac80211
In order to reduce reliance on mac80211 structs in the core
iwlwifi code, store the cipher schemes in the format given
by the firmware and convert it later, rather than storing it
in the mac80211 format.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Sara Sharon [Tue, 21 Jun 2016 11:14:08 +0000 (14:14 +0300)]
iwlwifi: mvm: free RX reorder buffer on restart
Restart flow zeroes the rx_ba_sessions counter. Mac80211 asks
driver to tear down of the session only afterwards, and as a
result driver didn't free the data. Fix it.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Fixes:
10b2b2019d81 ("iwlwifi: mvm: add infrastructure for tracking BA session in driver")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Sara Sharon [Tue, 21 Jun 2016 09:12:10 +0000 (12:12 +0300)]
iwlwifi: mvm: add RX aggregation prints
Add some prints to track BAID assignment.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Liad Kaufman [Wed, 30 Sep 2015 14:44:28 +0000 (16:44 +0200)]
iwlwifi: mvm: support dqa-mode scd queue redirection
Make sure that in DQA mode, the SCD's configuration of a
queue is redirected to the lower AC of the streams of the
queue.
Make sure that this queue is redirected to the lowest AC
when adding a new RA/TID to an existing queue. If it isn't -
redirect the queue.
Also, as redirection revealed a bug in the marking of a
shared queue, this patch contains a small fix to make
sure a shared queue maintains the appropriate "shared queue
marking".
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Liad Kaufman [Sun, 5 Jun 2016 07:49:02 +0000 (10:49 +0300)]
iwlwifi: mvm: support tdls in dqa mode
Support TDLS when working in DQA mode.
This is done mainly by NOT doing any special things
for TDLS, as the queues are dynamically created anyway,
so no need to allocate them ahead of time.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Sara Sharon [Tue, 21 Jun 2016 08:13:47 +0000 (11:13 +0300)]
iwlwifi: pcie: don't use vid 0
In cases of hardware or DMA error, the vid read from
a zeroed location will be 0, and we will access the rxb
at index 0 in the global table, while it may be NULL or
owned by hardware.
Invalidate vid 0 in order to detect the situation and
bail out.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Emmanuel Grumbach [Sun, 19 Jun 2016 17:57:02 +0000 (20:57 +0300)]
iwlwifi: mvm: unmap the paging memory before freeing it
This led to a DMA splat.
Fixes:
a6c4fb4441f4 ("iwlwifi: mvm: Add FW paging mechanism for the UMAC on PCI")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Johannes Berg [Tue, 21 Jun 2016 10:23:35 +0000 (12:23 +0200)]
iwlwifi: remove iwl_ht_params.smps_mode
This struct member is never set, so remove it.
Since this is the last thing that needs mac80211.h, also change
the includes to no longer use mac80211.h
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Emmanuel Grumbach [Wed, 22 Jun 2016 07:51:31 +0000 (10:51 +0300)]
iwlwifi: mvm: fix the channel inhibition table for Channel 14
The value for Channel 14 was wrong. Fix it.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Emmanuel Grumbach [Mon, 20 Jun 2016 06:40:40 +0000 (09:40 +0300)]
iwlwifi: mvm: fix coex related comments
Those comments were wrong, fix them.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Golan Ben-Ami [Wed, 15 Jun 2016 06:16:24 +0000 (09:16 +0300)]
iwlwifi: mvm: write the correct internal TXF index
The TX fifos are arranged consecutively in the SMEM, beginning
with the regular fifos, and tailed by the internal fifos.
In the current code, while trying to read the internal fifos,
we read the fifos beginning with the index zero.
By doing this we actually re-read the regular fifos.
In order to read the internal fifos, start the reading index
from the number of regular fifos configured by the fw.
Signed-off-by: Golan Ben-Ami <golan.ben.ami@intel.com>
Fixes:
39654cb3a6a2 ("iwlwifi: don't access a nonexistent register upon assert")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Sara Sharon [Thu, 9 Jun 2016 14:19:35 +0000 (17:19 +0300)]
iwlwifi: pcie: fix access to scratch buffer
This fixes a pretty ancient bug that hasn't manifested itself
until now.
The scratchbuf for command queue is allocated only for 32 slots
but is accessed with the queue write pointer - which can be
up to 256.
Since the scratch buf size was 16 and there are up to 256 TFDs
we never passed a page boundary when accessing the scratch buffer,
but when attempting to increase the size of the scratch buffer a
panic was quick to follow when trying to access the address resulted
in a page boundary.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Fixes:
38c0f334b359 ("iwlwifi: use coherent DMA memory for command header")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Ido Yariv [Tue, 14 Jun 2016 14:27:57 +0000 (10:27 -0400)]
iwlwifi: pcie: Enable MSI mode when using MSI interrupts
On some of the chipsets MSI & INTA interrupts are disabled by default in
the HW registers, and need to be explicitly enabled to be used.
In case MSI-X isn't used, make sure MSI mode is enabled by setting
the relevant HW register.
Signed-off-by: Ido Yariv <idox.yariv@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Luca Coelho [Mon, 30 May 2016 10:00:44 +0000 (13:00 +0300)]
iwlwifi: mvm: read SAR BIOS table from ACPI
Read the SAR BIOS table from the ACPI and parse it into the
iwl_mvm_sar_table structure. If the table is enabled, send it to the
firmware via REDUCE_TX_POWER_CMD.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Emmanuel Grumbach [Mon, 13 Jun 2016 07:02:04 +0000 (10:02 +0300)]
iwlwifi: mvm: cleanup the coex code
We removed support for old API for coexistence, but we
forgot to remove defines and variable that are not needed
anymore.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Sara Sharon [Wed, 8 Jun 2016 12:15:41 +0000 (15:15 +0300)]
iwlwifi: mvm: checksum IPv6 fragmented packet
Our HW does not support checksum of fragmented packets.
Fix code accordingly to checksum those packets in the driver.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Fixes:
5e6a98dc4863 ("iwlwifi: mvm: enable TCP/UDP checksum support for 9000 family")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
striebit [Tue, 7 Jun 2016 12:05:26 +0000 (15:05 +0300)]
iwlmvm: mvm: set correct state in smart-fifo configuration
Currently the state sent in SF configuration is always
FULL_ON.
This commit sets the correct state (e.g. INIT_OFF
when station is not associated).
Fixes: commit
f4a3ee493e69 ("iwlwifi: mvm: Always enable the smart FIFO")
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Emmanuel Grumbach [Wed, 8 Jun 2016 20:07:31 +0000 (23:07 +0300)]
iwlwifi: pcie: enable interrupts before releasing the NIC's CPU
The NIC's CPU gets started after the firmware has been
written to its memory. The first thing it does is to
send an interrupt to let the driver know that it is
running. In order to get that interrupt, the driver needs
to make sure it is not masked. Of course, the interrupt
needs to be enabled in the driver before the CPU starts to
run.
I mistakenly inversed those two steps leading to races
which prevented the driver from getting the alive interrupt
from the firmware.
Fix that.
Cc: <stable@vger.kernel.org> [4.5+]
Fixes:
a6bd005fe92 ("iwlwifi: pcie: fix RF-Kill vs. firmware load race")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Haim Dreyfuss [Tue, 31 May 2016 08:13:09 +0000 (11:13 +0300)]
iwlwifi: Add a000 HW family support
Add a000 family configuration to iwl-cfg struct
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Sara Sharon [Sun, 10 Apr 2016 12:06:55 +0000 (15:06 +0300)]
iwlwifi: mvm: support new statistics notification
For 9000 family we will get extended statistics notification
with averaged data for RSSI, TCM and rogue AP detection.
Support it. Future patches will added the required algorithms.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Ayala Beker [Thu, 7 Apr 2016 13:21:57 +0000 (16:21 +0300)]
iwlwifi: mvm: add support for GCMP encryption
Newer hardware supports GCMP and GCMP 256-bit ciphers.
Add support for adding/setting GCMP key for TX mode.
In the TX command handling GCMP-256 is handled in a different
way as the key size should be up to 128-bits:
Set the key value to the key index in the key table,
and specify that this key should be taken form the key table
instead of from the TX command.
While at it - convert security control flags to an enum.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Golan Ben-Ami [Thu, 19 May 2016 04:46:20 +0000 (07:46 +0300)]
iwlwifi: Reserve iwl_fw_error_dump_type enum
Reserve a single iwl_fw_error_dump_type enum for external
code utilities.
Signed-off-by: Golan Ben-Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Sara Sharon [Sun, 22 May 2016 13:25:40 +0000 (16:25 +0300)]
iwlwifi: add dump of RFH
Add support of dumping new RFH instead of FH registers.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Guenter Roeck [Fri, 3 Jun 2016 21:39:19 +0000 (14:39 -0700)]
iwlwifi: dvm: Remove unused array 'iwlagn_loose_lookup'
gcc-6 reports the following error if -Werror=unused-const-variable
is enabled.
drivers/net/wireless/intel/iwlwifi/dvm/lib.c:210:21: error:
'iwlagn_loose_lookup' defined but not used
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Oren Givon [Sun, 29 May 2016 11:05:50 +0000 (14:05 +0300)]
iwlwifi: mvm: fix txq aggregation bug
Fix an issue where nullfunc frames and block ack requests
had the same tid as aggregation frames and were queued on
a non aggregation queue. The pending frames counter included
those frames but the check whether to decrement the pending
frames counter relied on the tid status and not on the txq id.
The result was an inconsistent state of the pending frames
counter followed by a failure to remove the station.
This failure triggered SYSASSERT 0x3421.
In addition, fix a situation in DQA mode where the number
of pending frames turned negative. This was due to the TX queue
being on the IWL_EMPTYING_HW_QUEUE_DELBA state and its frames
were still decremented.
Even though the SYSASSERT issue is fixed when DQA is disabled,
the issue is not completely solved when DQA is enabled and
should still be fixed.
Signed-off-by: Oren Givon <oren.givon@intel.com>
Fixes:
cf961e16620f ("iwlwifi: mvm: support dqa-mode agg on non-shared queue")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Arnd Bergmann [Fri, 27 May 2016 13:07:03 +0000 (15:07 +0200)]
iwlwifi: mvm: avoid harmless -Wmaybe-uninialized warning
gcc is apparently unablel to track the state of the local 'resp_v2'
variable across the kzalloc() function, and warns about the response
variable being used without an initialization:
drivers/net/wireless/intel/iwlwifi/mvm/nvm.c: In function ‘iwl_mvm_update_mcc’:
drivers/net/wireless/intel/iwlwifi/mvm/nvm.c:727:36: warning: ‘mcc_resp_v1’ may be used uninitialized in this function [-Wmaybe-uninitialized]
resp_cp->n_channels = mcc_resp_v1->n_channels;
drivers/net/wireless/intel/iwlwifi/mvm/nvm.c:721:3: warning: ‘mcc_resp’ may be used uninitialized in this function [-Wmaybe-uninitialized]
memcpy(resp_cp, mcc_resp, resp_len);
The warning showed up in x86 allmodconfig after my patch to
unhide -Wmaybe-uninitialized warnings by default was merged,
though it always existed in randconfig builds. I did not
catch the warning earlier because I was testing on ARM, which
never produced the warning.
This rearranges the code in a way that improves readability for
both humans and the compiler, and that avoids the warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes:
6fa52430f0b3 ("iwlwifi: mvm: change mcc update API")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Gregory Greenman [Wed, 25 May 2016 15:31:39 +0000 (18:31 +0300)]
iwlwifi: mvm: rs: add rate scaling support for 160MHz channels
Expand TLC to support 160MHz channels. Full support for A-MSDU
case will be added separately.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Ayala Beker [Wed, 1 Jun 2016 08:46:20 +0000 (11:46 +0300)]
iwlwifi: mvm: fix RX mpdu status enum
FW sets status for each RX packet.
Enum in the driver doesn't match with FW definition - fix it.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Matti Gottlieb [Tue, 17 May 2016 07:50:08 +0000 (10:50 +0300)]
iwlwifi: mvm: Do not open aggregations for null data packets
Currently we try to open an aggregation for every packet (given that one
is not already open).
This causes redundant overhead (addba/delba) for null data packets.
Do not open an aggregation for null data packets.
Signed-off-by: Matti Gottlieb <matti.gottlieb@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Sara Sharon [Thu, 19 May 2016 14:53:42 +0000 (17:53 +0300)]
iwlwifi: pcie: poll RFH for RX DMA stop
Somehow we ended up stopping RX using legacy RX registers
even for devices that support RFH. Fix it.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Luca Coelho [Mon, 30 May 2016 09:52:43 +0000 (12:52 +0300)]
iwlwifi: mvm: remove unnecessary device conversion when reading the MCC
We convert the mvm device to a PCI device and then back again when
trying to find the handle for the device's ACPI data. This is
unnecessary, so it can be removed.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Oren Givon [Mon, 23 May 2016 06:58:17 +0000 (09:58 +0300)]
iwlwifi: add new 8265
Add 6 new 8265 series PCI IDs:
- (0x24FD, 0x1130)
- (0x24FD, 0x0130)
- (0x24FD, 0x0910)
- (0x24FD, 0x0930)
- (0x24FD, 0x0950)
- (0x24FD, 0x0850)
CC: <stable@vger.kernel.org> [4.6+]
Signed-off-by: Oren Givon <oren.givon@intel.com>
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Oren Givon [Mon, 23 May 2016 06:58:17 +0000 (09:58 +0300)]
iwlwifi: add new 8260 PCI IDs
Add 3 new 8260 series PCI IDs:
- (0x24F3, 0x10B0)
- (0x24F3, 0xD0B0)
- (0x24F3, 0xB0B0)
CC: <stable@vger.kernel.org> [4.1+]
Signed-off-by: Oren Givon <oren.givon@intel.com>
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Liad Kaufman [Mon, 31 Aug 2015 11:33:23 +0000 (14:33 +0300)]
iwlwifi: mvm: support dqa-enable hcmd
Support sending the DQA-enablement HCMD to the FW when
working in DQA mode.
This HCMD will enable DQA-specific flows in the FW.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Liad Kaufman [Tue, 1 Sep 2015 13:36:25 +0000 (16:36 +0300)]
iwlwifi: mvm: update aux queue in dqa mode
In DQA mode the AUX queue is mapped elsewhere than in non-
DQA mode. Update the code to reflect this.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Liad Kaufman [Mon, 31 Aug 2015 10:41:26 +0000 (13:41 +0300)]
iwlwifi: mvm: set sta_id in SCD_QUEUE_CONFIG cmd
Set the correct sta_id in the SCD_QUEUE_CONFIG command sent
to the FW when enabling/disabling queues. This is needed in
DQA-mode to allow the FW to associate between queue and STA.
In case the queue isn't connected to a specific station but
rather is a static "generic" queue - the sta_id should be
set to 0x10 (max supported STA is 0x0f).
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Liad Kaufman [Mon, 2 May 2016 11:01:14 +0000 (14:01 +0300)]
iwlwifi: mvm: support dqa queue sharing
Support DQA queue sharing when no free queue exists for
allocation to a STA that already exists. This means that
a single queue will serve more than a single TID (although
the RA will be the same for all TIDs served).
We try to choose the lowest AC possible, to ensure the
shared queues have the lowest possible combined AC
requirements. The queue to share is chosen only from the
same RA's DATA queues as follows (in descending priority):
1. An AC_BE queue
2. Same AC queue
3. Highest AC queue that is lower than new AC
4. Any existing AC (there always is at least 1 DATA queue)
If any aggregations existed for any of the TIDs of the
shared queue - they are stopped (the FW is notified), but
no delBA is sent.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Dan Carpenter [Wed, 4 May 2016 06:19:54 +0000 (09:19 +0300)]
iwlwifi: mvm: silence uninitialized variable warning
"max_amsdu_len" isn't set if kstrtouint() fails.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Dan Carpenter [Wed, 4 May 2016 06:19:13 +0000 (09:19 +0300)]
iwlwifi: mvm: remove an unused variable
We never initialize ampdu_status so it causes a static checker warning
when we pass it to iwl_mvm_pass_packet_to_mac80211(). Fortunately, it's
never used so we can just remove it.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Luca Coelho [Tue, 3 May 2016 09:18:33 +0000 (12:18 +0300)]
iwlwifi: mvm: change scan timeout to a delayed work
Some transports may sleep when writing to registers, which is done
when calling iwl_force_nmi(). So we can't call iwl_force_nmi() in a
timer context. To solve that, convert the scan timeout timer to a
delayed work.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Sara Sharon [Wed, 4 May 2016 11:22:10 +0000 (14:22 +0300)]
iwlwifi: mvm: fix possible division by zero
Theoretically we may get only one IRQ from OS, in which
case we will have only 1 queue even in MSIx mode.
This will cause division by zero in the indirection table
calculation.
We do not need send the command in that case, as there is
only one queue so all RX traffic will be directed to it
anyway. Bail out early if there is only one queue.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Sara Sharon [Sun, 1 May 2016 08:40:49 +0000 (11:40 +0300)]
iwlwifi: pcie: unify restock calls on init
Currently code calls restock for mq devices during the init
function, unlike sq where restock is called after init.
This causes an harmless but alarming deadlock warning from
lockdep, to fix this - unify the init code.
Rename the restock functions while at it.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Liad Kaufman [Wed, 19 Aug 2015 14:34:28 +0000 (17:34 +0300)]
iwlwifi: mvm: support dqa queue inactivation upon timeout
Support marking queues as inactive upon a timeout expiring,
and allow inactive queues to be re-assigned to other RA/TIDs
if no other queue is free.
This is done by keeping a timestamp of the latest frame TXed
for every RA/TID, and then going over the queues currently in
use when a new queue is needed, inactivating all those that
are inactive.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Johannes Berg [Thu, 28 Apr 2016 12:40:59 +0000 (14:40 +0200)]
iwlwifi: change fw.mvm_fw to fw.type
Instead of explicitly indicating the difference between just
DVM and MVM with an mvm_fw boolean change this to fw.type to
be more extensible and easier to understand.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Johannes Berg [Thu, 28 Apr 2016 12:39:22 +0000 (14:39 +0200)]
iwlwifi: remove useless enum values
Since the values of this enum are used only internally,
we can let the compiler number them.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Larry Finger [Sat, 25 Jun 2016 18:37:47 +0000 (13:37 -0500)]
rtlwifi: rtl8821ae: Fix potential race condition
Flag rfchange_inprogress in struct rtl_ps_ctl is protected by a spinlock
in most routines but not in rtl8821ae_dm_watchdog() which could
lead to a race condition. The necessary locking to prevent this condition
is added.
Reported-by: Pavel Andrianov <andrianov@ispras.ru>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pavel Andrianov <andrianov@ispras.ru>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Larry Finger [Sat, 25 Jun 2016 18:37:46 +0000 (13:37 -0500)]
rtlwifi: rtl8723ae: Fix potential race condition
Flag rfchange_inprogress in struct rtl_ps_ctl is protected by a spinlock
in most routines but not in rtl8723e_dm_watchdog(), which could
lead to a race condition. The necessary locking to prevent this condition
is added.
Reported-by: Pavel Andrianov <andrianov@ispras.ru>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pavel Andrianov <andrianov@ispras.ru>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Larry Finger [Sat, 25 Jun 2016 18:37:45 +0000 (13:37 -0500)]
rtlwifi: rtl8723be: Fix potential race condition
Flag rfchange_inprogress in struct rtl_ps_ctl is protected by a spinlock
in most routines but not in rtl8723be_dm_watchdog(), which could
lead to a race condition. The necessary locking to prevent this condition
is added.
Reported-by: Pavel Andrianov <andrianov@ispras.ru>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pavel Andrianov <andrianov@ispras.ru>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>