media: i2c: imx219: Add support for cropped 640x480 resolution

This patch adds mode table entry for capturing cropped 640x480 resolution

Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Acked-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: i2c: imx219: Add support for RAW8 bit bayer format

IMX219 sensor is capable for RAW8/RAW10 modes. This commit adds support
for RAW8 bayer format.

Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: i2c: imx219: Fix power sequence

When supporting Rpi Camera v2 Module on the RZ/G2E, found the driver had
some issues with rcar mipi-csi driver. The sensor never entered into LP-11
state.

The powerup sequence in the datasheet[1] shows the sensor entering into
LP-11 in streaming mode, so to fix this issue transitions are performed
from "streaming -> standby" in the probe() after power up.

With this commit the sensor is able to enter LP-11 mode during power up,
as expected by some CSI-2 controllers.

[1] https://publiclab.org/system/images/photos/000/023/294/original/
RASPBERRY_PI_CAMERA_V2_DATASHEET_IMX219PQH5_7.0.0_Datasheet_XXX.PDF

Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Acked-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: MAINTAINERS: adjust entry to refactoring smiapp.h

Commit 7cbeb2e1bf0c ("media: smiapp: Move definitions under driver
directory") moved the definitions in include/media/i2c/smiapp.h into other
files and removed include/media/i2c/smiapp.h.

Since then, ./scripts/get_maintainer.pl --self-test complains:

  warning: no file matches F: include/media/i2c/smiapp.h

Remove MAINTAINER file entry to this removed file and while at it, update
Sakari's email address in this section.

Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: mailmap: Add entry for my @iki.fi address

Add entry for my @iki.fi e-mail address to the mailmap.

Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: staging: imgu: make imgu work on low frequency for low input

Currently, imgu is working on 450MHz for all cases, however
in some cases (input frame less than 2048x1152), the imgu
did not need work in high frequency.
This patch make imgu work on 200MHz if the imgu input
frame is less than 2048x1152 to save power.

Signed-off-by: Bingbu Cao <bingbu.cao@intel.com>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: Fix build failure due to missing select REGMAP_I2C

While upgrading from 5.5.2 -> 5.5.6 I was surprised by:
ld: drivers/media/i2c/tvp5150.o: in function `tvp5150_probe':
tvp5150.c:(.text+0x11ac): undefined reference to
`__devm_regmap_init_i2c'
make: *** [Makefile:1078: vmlinux] Error 1

The fix was quick enough, make VIDEO_TVP5150 select REGMAP_I2C
And a quick grep showed that it was needed by more targets.

Signed-off-by: Ian Kumlien <ian.kumlien@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: tvp5150: make debug output more readable

The debug output for tvp5150_selmux() isn't really intuitive. Register
values are printed decimal formatted and the input/output driver states
are printed as enum. Even more the "normal" output enum mapps to zero so
a active output will printing output=0 and a inactive output=1.

Change this by brinting the register values hex formatted and the states
as more readable string.

Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: tvp5150: add support to limit sdtv standards

The tvp5150 accepts NTSC(M,J,4.43), PAL (B,D,G,H,I,M,N) and SECAM video
data and is able to auto-detect the input signal. The auto-detection
does not work if the connector does not receive an input signal and the
tvp5150 might not be configured correctly. This misconfiguration leads
into wrong decoded video streams if the tvp5150 gets powered on before
the video signal is present.

Limit the supported sdtv standards according to the actual selected
connector to avoid a misconfiguration.

Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: dt-bindings: tvp5150: add optional sdtv standards documentation

Document the optional binding to limit the possible sdtv standards on the
input connectors.

Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: dt-bindings: tvp5150: cleanup bindings stlye

Use underlines to highlight optional and required properties. This is
quite common for all bindings. Align descriptions and start sentence
with uppercase letter. Also reword the usage of the required
endpoint properties for the output port in case BT.656 should be used.

Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: tvp5150: add subdev open/close callbacks

Bring the device into a working state upon a open/close call. Currently
this involves only the interrupt enable/disable process but can be
extended in the future.

Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: tvp5150: add v4l2-event support

Currently the driver notifies internal subdevs if the signal is locked
or not. This information is also useful for userpace applications e.g. to
switch to another input device upon a signal lost event.

This commit adds the support for the userspace to subscribe to the
V4L2_EVENT_SOURCE_CHANGE and V4L2_EVENT_CTRL events.

Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: tvp5150: move irq en-/disable into runtime-pm ops

As documented in [1] the runtime-pm ops are used to set the device into
a fully 'workable' state. Therefore it can be used to enable or disable
the irqs.

[1] https://www.kernel.org/doc/html/latest/power/runtime_pm.html

Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: tvp5150: initialize subdev before parsing device tree

There are several debug prints in the tvp5150_parse_dt() function, which
do not print the prefix, because the v4l2_subdev is not initialized, yet.

Initialize the v4l2_subdev before parsing the device tree to fix the
debug messages.

Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: tvp5150: add FORMAT_TRY support for get/set selection handlers

Since commit 10d5509c8d50 ("[media] v4l2: remove g/s_crop from video ops")
the 'which' field for set/get_selection must be FORMAT_ACTIVE. There is
no way to try different selections. The patch adds a helper function to
select the correct selection memory space (sub-device file handle or
driver state) which will be set/returned.

The selection rectangle is updated if the format is FORMAT_ACTIVE and
the rectangle position and/or size differs from the current set
rectangle.

Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: tvp5150: fix set_selection rectangle handling

Currently a local copy of sel->r is made and adapted to the hardware
constraints. After the adaption the value is applied to the hardware but
the driver forgot to reflect the adapted value to the user space.

Drop the local copy and work directly on the requested rectangle
instead to fix this.

Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: dt-bindings: tvp5150: Add input port connectors DT bindings

The TVP5150/1 decoders support different video input sources to their
AIP1A/B pins.

Possible configurations are as follows:
  - Analog Composite signal connected to AIP1A.
  - Analog Composite signal connected to AIP1B.
  - Analog S-Video Y (luminance) and C (chrominance)
    signals connected to AIP1A and AIP1B respectively.

This patch extends the device tree bindings documentation to describe
how the input connectors for these devices should be defined in a DT.

Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: tvp5150: add input source selection of_graph support

This patch adds the of_graph support to describe the tvp input connections.
Physical the TVP5150 has three ports: AIP1A, AIP1B and YOUT. As result
of discussion [1],[2] the device-tree maps these ports 1:1. Look at the
Documentation for more information. Since the TVP5150 is a converter/bridge
the device-tree must contain at least 1-input and 1-output port. The
mc-connectors and mc-links are only created if the device-tree contains the
corresponding connector nodes. If more than one connector is available the
media_entity_operations.link_setup() callback ensures that only one
connector is active.

[1] https://www.spinics.net/lists/linux-media/msg138545.html
[2] https://www.spinics.net/lists/linux-media/msg138546.html

Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: partial revert of "[media] tvp5150: add HW input connectors support"

Commit f7b4b54e6364 ("[media] tvp5150: add HW input connectors support")
added input signals support for the tvp5150, but the approach was found
to be incorrect so the corresponding DT binding commit 82c2ffeb217a
("[media] tvp5150: document input connectors DT bindings") was reverted.

This left the driver with an undocumented (and wrong) DT parsing logic,
so lets get rid of this code as well until the input connectors support
is implemented properly.

It's a partial revert due other patches added on top of mentioned commit
not allowing the commit to be reverted cleanly anymore. But all the code
related to the DT parsing logic and input entities creation are removed.

Suggested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
[m.felsch@pengutronix.de: rm TVP5150_INPUT_NUM define]
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: v4l2-fwnode: add initial connector parsing support

The patch adds the initial connector parsing code, so we can move from a
driver specific parsing code to a generic one. Currently only the
generic fields and the analog-connector specific fields are parsed. Parsing
the other connector specific fields can be added by a simple callbacks.

Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
[hverkuil-cisco@xs4all.nl: replace ; with break; in a empty case]
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: v4l2-fwnode: add v4l2_fwnode_connector

Currently every driver needs to parse the connector endpoints by it self.
This is the initial work to make this generic. A generic connector has
common members and connector specific members. The common members are:
  - type
  - label (optional)
  - links
  - nr_of_links

The specific members are stored within a union, since only one of them
can be available at the time. Since this is the initial support the
patch adds only the analog-connector specific ones.

Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: v4l2-fwnode: add endpoint id field to v4l2_fwnode_link

A link is between two endpoints not between two ports to be more
precise. Add the local_id/remote_id field which stores the endpoint
reg/port property to the link. Now the link holds all necessary
information about a link.

Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: v4l2-fwnode: simplify v4l2_fwnode_parse_link

This helper was introduced before those helpers where awailable. Convert
it to cleanup the code and improbe readability.

Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: v4l2-fwnode: fix v4l2_fwnode_parse_link handling

Currently the driver differentiate the port number property handling for
ACPI and DT. This is wrong as because ACPI should use the "reg" val too
[1].

[1] https://patchwork.kernel.org/patch/11421985/

Fixes: ca50c197bd96 ("[media] v4l: fwnode: Support generic fwnode for parsing standardised properties")
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: v4l: link dt-bindings and uapi

Since we expose the definition to the dt-bindings we need to keep those
definitions in sync. To address this the patch adds a simple cross
reference to the dt-bindings.

Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: dt-bindings: display: add sdtv-standards defines

Add defines which can be included to easily describe the supported
standard tv norms 'sdtv-standards' within the device tree.

Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: dt-bindings: connector: analog: add sdtv standards property

Some connectors no matter if in- or output supports only a limited
range of sdtv standards. It doesn't matter if the hardware behind that
connector supports more than the listed formats since the users are
restriced by a label e.g. to plug only a camera into this connector
which uses the PAL format.

This patch adds the capability to describe such limitation within the
firmware. There are no format restrictions if the property isn't
present, so it's completely backward compatible.

Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: am437x-vpfe: exclude illegal values for enum when validing params from user space

When calling ccdc_data_size_max_bit() to validate data_sz in
vpfe_ccdc_validate_param(), it's treated as an enumeration ranging from
0 to 7 while essentially it's an 32 bit unsigned integer directly from
user space. This can make the return value of ccdc_data_size_max_bit()
underflow and bypass the following check.

To fix this, an additional check is added to the following if clause to
keep this enumaration variable in range. And if its value is not legal,
return -EINVAL properly.

Signed-off-by: Changming Liu <charley.ashbringer@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: ti-vpe: cal: fix a kernel oops when unloading module

After the switch to use v4l2_async_notifier_add_subdev() and
v4l2_async_notifier_cleanup(), unloading the ti_cal module would cause a
kernel oops.

This was root cause to the fact that v4l2_async_notifier_cleanup() tries
to kfree the asd pointer passed into v4l2_async_notifier_add_subdev().

In our case the asd reference was from a statically allocated struct.
So in effect v4l2_async_notifier_cleanup() was trying to free a pointer
that was not kalloc.

So here we switch to using a kzalloc struct instead of a static one.
To achieve this we re-order some of the calls to prevent asd allocation
from leaking.

Fixes: d079f94c9046 ("media: platform: Switch to v4l2_async_notifier_add_subdev")
Cc: stable@vger.kernel.org
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: mtk-vpu: avoid unaligned access to DTCM buffer.

Previously, vpu->recv_buf and send_buf are forced cast from
void __iomem *tcm. vpu->recv_buf->share_buf is passed to
vpu_ipi_desc.handler(). It's not able to do unaligned access. Otherwise
kernel would crash due to unable to handle kernel paging request.

struct vpu_run {
u32 signaled;
char fw_ver[VPU_FW_VER_LEN];
unsigned int dec_capability;
unsigned int enc_capability;
wait_queue_head_t wq;
};

fw_ver starts at 4 byte boundary. If system enables
CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS, strscpy() will do
read_word_at_a_time(), which tries to read 8-byte: *(unsigned long *)addr

vpu_init_ipi_handler() calls strscpy(), which would lead to crash.

vpu_init_ipi_handler() and several other handlers (eg.
vpu_dec_ipi_handler) only do read access to this data, so they can be
const, and we can use memcpy_fromio() to copy the buf to another non iomem
buffer then pass to handler.

Fixes: 85709cbf1524 ("media: replace strncpy() by strscpy()")
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: venus: support frame rate control

Add encoder control for enabling/disabling frame rate control via
V4L2_CID_MPEG_VIDEO_FRAME_RC_ENABLE. It is enabled by default.

Signed-off-by: Jeffrey Kardatzke <jkardatzke@google.com>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: venus: vdec: Fix forgotten mutex unlock in start streaming

This fixes the following smatch warning in the error path:

drivers/media/platform/qcom/venus/vdec.c:968 vdec_start_streaming()
 warn: inconsistent returns 'mutex:&inst->lock'.
  Locked on:   line 952
  Unlocked on: line 963
               line 968

by goto mutex unlock.

Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: lmedm04: remove redundant assignment to variable gate

The variable gate is being initialized and also checked and re-assigned
with values that are never read as it is being re-assigned later in a
for-loop with a new value.  The assignments are redundant and can be
removed.

Addresses Coverity ("Unused value")

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: tda10071: fix unsigned sign extension overflow

The shifting of buf[3] by 24 bits to the left will be promoted to
a 32 bit signed int and then sign-extended to an unsigned long. In
the unlikely event that the the top bit of buf[3] is set then all
then all the upper bits end up as also being set because of
the sign-extension and this affect the ev->post_bit_error sum.
Fix this by using the temporary u32 variable bit_error to avoid
the sign-extension promotion. This also removes the need to do the
computation twice.

Addresses-Coverity: ("Unintended sign extension")

Fixes: 267897a4708f ("[media] tda10071: implement DVBv5 statistics")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: dw2102: probe for demodulator i2c address

This is required to support the Terratec S2 USB Box Revision 4, which
reused usb vid:pid, but has a different demodulator (m88ds3103b) at
i2c address 0x6a.

[fixed checkpatch issues]

Signed-off-by: Michael Bunk <micha@freedict.org>
Signed-off-by: Brad Love <brad@nextdimension.cc>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: em28xx: Enable Hauppauge 461e rev2

Hauppauge 461e rev2 is a DVB-S/S2 usb device containing:
- m88ds3103b demod
- ts2022 tuner
- A8293 SEC

Device is the same as Hauppauge 461e,
except it contains updated m88ds3103b demod.

Signed-off-by: Brad Love <brad@nextdimension.cc>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: m88ds3103: Add support for ds3103b demod

The ds3103b demodulator identifies as an m88rs600, but requires different
clock settings and firmware, along with differences in register settings.

Changes were reverse engineered using an instrumented downstream GPLv2
driver to compare i2c traffic and clocking. The mclk functions are from
the downstream GPLv2 driver.

Signed-off-by: Brad Love <brad@nextdimension.cc>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: rc: make scancodes 64 bit

There are many protocols that encode more than 32 bit. We want 64 bit
support so that BPF IR decoders can decode more than 32 bit. None of
the existing kernel IR decoders/encoders support 64 bit, for now.

The MSC_SCAN event can only contain 32 bit scancodes, so we only generate
MSC_SCAN events if the scancode fits into 32 bits. The full 64 bit
scancode can be read from the lirc chardev.

Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: meson: vdec: add VP9 decoder support

This adds VP9 decoding for the Amlogic GXL, G12A & SM1 SoCs, using
the commong "HEVC" HW decoder.

For G12A & SM1, it uses the IOMMU support from the firmware.

For 10bit decoding, the firmware can only decode in the proprietary
Amlogic Framebuffer Compression format, but can output in 8bit NV12
buffer while writing the decoded frame.

Signed-off-by: Maxime Jourdan <mjourdan@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: meson: vdec: add VP9 input support

Amlogic VP9 decoder requires an additional 16-byte payload before every
frame header.

The source buffer is updated in-place, then given to the Parser FIFO DMA.

The FIFO DMA copies the blocks into the 16MiB parser ring buffer, then parses
and copies the slice into the decoder "workspace".

Signed-off-by: Maxime Jourdan <mjourdan@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: meson: vdec: add common HEVC decoder support

Add support for the HEVC & VP9 common decoder support, handling
Amlogic GXBB, GXL, G12A and SM1 platforms.

This handles the "HEVC" hw decoder used for HEVC and VP9, and will be
using in the new H264 multi-instance decoder for G12A & SM1 platforms.

Signed-off-by: Maxime Jourdan <mjourdan@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: meson: vdec: add helpers for lossless framebuffer compression buffers

Add helpers to support the lossless framebuffer compression format that
will be used in HEVC & VP9 decoders when decoding 10bit content for
downsampling to 8bit NV12 and later proper compressed buffer support.

Signed-off-by: Maxime Jourdan <mjourdan@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: meson: vdec: align stride on 32 bytes

The HEVC/VP9 aligns the plane stride on 32, so align the planes stride
for all codecs to 32 to satisfy HEVC/VP9 decoding using the "HEVC" HW.

This fixes VP9 decoding of streams with following (not limited) widths:
- 264
 -288
- 350
- 352
- 472
- 480
- 528
- 600
- 720
- 800
- 848
- 1440

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: meson: vdec: add H.264 decoding support

Add support for the H264 compressed format (V4L2_PIX_FMT_H264).

Signed-off-by: Maxime Jourdan <mjourdan@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: meson: vdec: bring up to compliance

Add all the necessary bits to pass v4l2-compliance in stateful decoding
mode.

Mostly includes tracking the state of the decoder, allowing the OUTPUT
queue to stream while the CAPTURE queue is inactive, handling resolution
change events, draining with V4L2_DEC_CMD_STOP, copying more metadata
from the src buffers to the dst buffers, etc.

Signed-off-by: Maxime Jourdan <mjourdan@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: vicodec: use v4l2-mem2mem draining, stopped and next-buf-is-last states handling

Use the previously introduced v4l2-mem2mem core APIs to handle the drainig,
stopped and next-buf-is-last states.

With these changes, the v4l2-compliance still passes with the following
commands :
>>>><><><><><><><><><><><><><><><><>< 15.53 fps
 15.53 fps
><><><><><><><><><><><><>< 13.99 fps
 13.99 fps
><><><><><><><><><><><>< 13.52 fps
 13.52 fps
><><><><><><><><><><><><>< 13.41 fps
 13.41 fps
><><><><><><><><><><><><>< 13.21 fps
 13.21 fps
><><><><><><><><><><><>< 13.09 fps
 13.09 fps
><><><><><><><
STOP ENCODER
<<<
EOS EVENT

v4l2-compliance SHA: 7ead0e1856b89f2e19369af452bb03fd0cd16793, 64 bits
[...]
Total for vicodec device /dev/video0: 50, Succeeded: 50, Failed: 0, Warnings: 0

The full output is available at [1]

v4l2-compliance SHA: 7ead0e1856b89f2e19369af452bb03fd0cd16793, 64 bits
[...]
Total for vicodec device /dev/video1: 50, Succeeded: 50, Failed: 0, Warnings: 0

The full output is available at [2]

No functional changes should be noticed.

[1] https://termbin.com/25nn
[2] https://termbin.com/dza4

Suggested-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Suggested-by: Maxime Jourdan <mjourdan@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: v4l2-mem2mem: handle draining, stopped and next-buf-is-last states

Since the draining and stop phase of the HW decoder mem2mem bahaviour is
now clearly defined, we can move handling of the following states to the
common v4l2-mem2mem core code:
- draining
- stopped
- next-buf-is-last

By introducing the following v4l2-mem2mem APIs:
- v4l2_m2m_encoder_cmd/v4l2_m2m_ioctl_encoder_cmd to handle start/stop command
- v4l2_m2m_decoder_cmd/v4l2_m2m_ioctl_decoder_cmd to handle start/stop command
- v4l2_m2m_update_start_streaming_state to update state on start of streaming
of the de/encoder queue
- v4l2_m2m_update_stop_streaming_state to update state on stop of streaming
of the de/encoder queue
- v4l2_m2m_last_buffer_done to make the current dest buffer as the last one

And inline helpers:
- v4l2_m2m_mark_stopped to mark the de/encoding process as stopped
- v4l2_m2m_clear_state to clear the de/encoding state
- v4l2_m2m_dst_buf_is_last to detect the current dequeued dst_buf is the last
- v4l2_m2m_has_stopped to detect the de/encoding stopped state
- v4l2_m2m_is_last_draining_src_buf to detect the current source buffer should
 be the last processing before stopping the de/encoding process

The special next-buf-is-last when min_buffers != 1 case is also handled
in v4l2_m2m_qbuf() by reusing the other introduced APIs.

This state management has been stolen from the vicodec implementation,
and is no-op for drivers not calling the v4l2_m2m_encoder_cmd or
v4l2_m2m_decoder_cmd and v4l2_m2m_update_start/stop_streaming_state.

The vicodec will be the first one to be converted as an example.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: v4l2-ctrls: v4l2_ctrl_request_complete() should always set ref->req

When the request is completed, all controls are copied to the request object.
However, when VIDIOC_G_EXT_CTRLS attempts to read control values from the
request it will read the current value instead for any control reference that
has a NULL ref->req pointer. But that's wrong: after completing the request
*all* controls should have a non-NULL ref->req pointer since they are after
all copied to the request.

So set ref->req if it wasn't set already.

Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reported-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: staging: media: usbvision: Add missing MEDIA_USB_SUPPORT dependency

VIDEO_USBVISION driver depends on MEDIA_USB_SUPPORT

Fixes: 8fb12ce2ec9d ("media: usbvision: deprecate driver")

Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: staging: tegra-vde: Use devm_platform_ioremap_resource_byname()

There is a new devm_platform_ioremap_resource_byname() helper in the
kernel now, which helps to make code cleaner a tad by replacing few
"boilerplate" lines of code with a single line. Let's utilize that
new helper in the VDE driver.

Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: ti-vpe: cal: fix disable_irqs to only the intended target

disable_irqs() was mistakenly disabling all interrupts when called.
This cause all port stream to stop even if only stopping one of them.

Cc: stable <stable@vger.kernel.org>
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: imx: Propagate quantization and encoding in CSI

Unlike the PRPENC and PRPVF subdevices, the CSI's cannot convert
quantization from sink to source, or do any kind of Y'CbCr <-> RGB
encoding. So the CSI's cannot allow quantization and ycbcr_enc to be
selectable by the user and must be propagated from sink to source.

Fixes: 4791bd7d6adc4 ("media: imx: Try colorimetry at both sink and source pads")

Reported-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Steve Longerbeam <slongerbeam@gmail.com>
Tested-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Rui Miguel Silva <rmfrfs@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: v4l2: Switch to new kerneldoc syntax for named variable macro arguments

The new syntax is available since commit 43756e347f21
("scripts/kernel-doc: Add support for named variable macro arguments").

The same HTML output is produced with and without this patch.

Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: spi: gs1662: Use new structure for SPI transfer delays

In a recent change to the SPI subsystem [1], a new `delay` struct was added
to replace the `delay_usecs`. This change replaces the current
`delay_usecs` with `delay` for this driver.

The `spi_transfer_delay_exec()` function [in the SPI framework] makes sure
that both `delay_usecs` & `delay` are used (in this order to preserve
backwards compatibility).

[1] commit bebcfd272df6 ("spi: introduce `delay` field for
`spi_transfer` + spi_transfer_delay_exec()")

Signed-off-by: Sergiu Cuciurean <sergiu.cuciurean@analog.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: v4l2-core: fix entity initialization in device_register_subdev

The entity variable was being initialized in the wrong place, before the
parameters have been checked.
To solve this, completely removed the entity variable and replaced it
with the initialization value : &sd->entity.
This will avoid dereferencing 'sd' pointer before it's being checked if
it's NULL.

Fixes: 61f5db549dde ("[media] v4l: Make v4l2_subdev inherit from media_entity")

Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: v4l2-core: fix a use-after-free bug of sd->devnode

sd->devnode is released after calling
v4l2_subdev_release. Therefore it should be set
to NULL so that the subdev won't hold a pointer
to a released object. This fixes a reference
after free bug in function
v4l2_device_unregister_subdev

Fixes: 0e43734d4c46e ("media: v4l2-subdev: add release() internal op")

Cc: stable@vger.kernel.org
Signed-off-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
Reviewed-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: vimc: use-after-free fix - release vimc in the v4l_device release

A use-after-free bug occures when unbinding the device while it streams.
The 'struct vimc_ent_device' allocated for the 'Sensor A' is freed
when calling the sensor's 'rm' callback but the freed pointer is
later accessed in the function 'vimc_streamer_pipeline_terminate'.
To fix this bug, move the release callback of the vimc entities
and vimc_device to the release callback of v4l2_device.
The .rm callback of vimc_ent_config is replaced by two callbacks:

.unregister - this is called upon removing the device and
it unregisters the entity. This is an optional callback since
subdevices don't need to implement it because they are already
unregistered in v4l2_device_unregister.

.release - this is called from the release callback of v4l2_device
and it frees the entity.

This ensures that the entities will be released when the last fh
of any of the devices is closed.

The commands that cause the crash and the KASAN report:

media-ctl -d platform:vimc -V '"Sensor A":0[fmt:SBGGR8_1X8/640x480]'
media-ctl -d platform:vimc -V '"Debayer A":0[fmt:SBGGR8_1X8/640x480]'
v4l2-ctl -z platform:vimc -d "RGB/YUV Capture" -v width=1920,height=1440
v4l2-ctl -z platform:vimc -d "Raw Capture 0" -v pixelformat=BA81
v4l2-ctl --stream-mmap --stream-count=1000 -d /dev/video2 &
sleep 1
echo -n vimc.0 >/sys/bus/platform/drivers/vimc/unbind

[  188.417934] BUG: KASAN: use-after-free in vimc_streamer_pipeline_terminate+0x75/0x140 [vimc]
[  188.420182] Read of size 8 at addr ffff8881e9c26008 by task bash/185
[  188.421800]
[  188.422223] CPU: 0 PID: 185 Comm: bash Not tainted 5.5.0-rc1+ #1
[  188.423681] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.12.0-1 04/01/2014
[  188.425938] Call Trace:
[  188.426610]  dump_stack+0x75/0xa0
[  188.427519]  ? vimc_streamer_pipeline_terminate+0x75/0x140 [vimc]
[  188.429057]  print_address_description.constprop.6+0x16/0x220
[  188.430462]  ? vimc_streamer_pipeline_terminate+0x75/0x140 [vimc]
[  188.431979]  ? vimc_streamer_pipeline_terminate+0x75/0x140 [vimc]
[  188.433455]  __kasan_report.cold.9+0x1a/0x40
[  188.434518]  ? vimc_streamer_pipeline_terminate+0x75/0x140 [vimc]
[  188.436010]  kasan_report+0xe/0x20
[  188.436859]  vimc_streamer_pipeline_terminate+0x75/0x140 [vimc]
[  188.438339]  vimc_streamer_s_stream+0x8b/0x3c0 [vimc]
[  188.439576]  vimc_cap_stop_streaming+0x22/0x40 [vimc]
[  188.440863]  __vb2_queue_cancel+0x65/0x560 [videobuf2_common]
[  188.442391]  vb2_core_queue_release+0x19/0x50 [videobuf2_common]
[  188.443974]  vimc_cap_rm+0x10/0x20 [vimc]
[  188.444986]  vimc_rm_subdevs+0x9e/0xe0 [vimc]
[  188.446179]  vimc_remove+0x19/0x70 [vimc]
[  188.447301]  platform_drv_remove+0x2f/0x50
[  188.448468]  device_release_driver_internal+0x133/0x260
[  188.449814]  unbind_store+0x121/0x150
[  188.450726]  kernfs_fop_write+0x142/0x230
[  188.451724]  ? sysfs_kf_bin_read+0x100/0x100
[  188.452826]  vfs_write+0xdc/0x230
[  188.453760]  ksys_write+0xaf/0x140
[  188.454702]  ? __ia32_sys_read+0x40/0x40
[  188.455773]  ? __do_page_fault+0x473/0x620
[  188.456780]  do_syscall_64+0x5e/0x1a0
[  188.457711]  entry_SYSCALL_64_after_hwframe+0x44/0xa9
[  188.459079] RIP: 0033:0x7f80f1f13504
[  188.459969] Code: 00 f7 d8 64 89 02 48 c7 c0 ff ff ff ff eb b3 0f 1f 80 00 00 00 00 48 8d 05 f9 61 0d 00 8b 00 85 c0 75 13 b8 01 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 54 c3 0f 1f 00 41 54 49 89 d4 55 48 89 f5 53
[  188.464445] RSP: 002b:00007ffd7e843b58 EFLAGS: 00000246 ORIG_RAX: 0000000000000001
[  188.466276] RAX: ffffffffffffffda RBX: 0000000000000006 RCX: 00007f80f1f13504
[  188.467999] RDX: 0000000000000006 RSI: 000055ef2eb21b10 RDI: 0000000000000001
[  188.469708] RBP: 000055ef2eb21b10 R08: 00007f80f1fe68c0 R09: 00007f80f1e26740
[  188.471407] R10: 000055ef2eade010 R11: 0000000000000246 R12: 00007f80f1fe5760
[  188.473381] R13: 0000000000000006 R14: 00007f80f1fe0760 R15: 0000000000000006
[  188.475107]
[  188.475500] Allocated by task 473:
[  188.476351]  save_stack+0x19/0x80
[  188.477201]  __kasan_kmalloc.constprop.6+0xc1/0xd0
[  188.478507]  vimc_sen_add+0x36/0x309 [vimc]
[  188.479649]  vimc_probe+0x1e2/0x530 [vimc]
[  188.480776]  platform_drv_probe+0x46/0xa0
[  188.481829]  really_probe+0x16c/0x520
[  188.482732]  driver_probe_device+0x114/0x170
[  188.483783]  device_driver_attach+0x85/0x90
[  188.484800]  __driver_attach+0xa8/0x190
[  188.485734]  bus_for_each_dev+0xe4/0x140
[  188.486702]  bus_add_driver+0x223/0x2d0
[  188.487715]  driver_register+0xca/0x140
[  188.488767]  0xffffffffc037003d
[  188.489635]  do_one_initcall+0x86/0x28f
[  188.490702]  do_init_module+0xf8/0x340
[  188.491773]  load_module+0x3766/0x3a10
[  188.492811]  __do_sys_finit_module+0x11a/0x1b0
[  188.494059]  do_syscall_64+0x5e/0x1a0
[  188.495079]  entry_SYSCALL_64_after_hwframe+0x44/0xa9
[  188.496481]
[  188.496893] Freed by task 185:
[  188.497670]  save_stack+0x19/0x80
[  188.498493]  __kasan_slab_free+0x125/0x170
[  188.499486]  kfree+0x8c/0x230
[  188.500254]  v4l2_subdev_release+0x64/0x70 [videodev]
[  188.501498]  v4l2_device_release_subdev_node+0x1c/0x30 [videodev]
[  188.502976]  device_release+0x3c/0xd0
[  188.503867]  kobject_put+0xf4/0x240
[  188.507802]  vimc_rm_subdevs+0x9e/0xe0 [vimc]
[  188.508846]  vimc_remove+0x19/0x70 [vimc]
[  188.509792]  platform_drv_remove+0x2f/0x50
[  188.510752]  device_release_driver_internal+0x133/0x260
[  188.512006]  unbind_store+0x121/0x150
[  188.512899]  kernfs_fop_write+0x142/0x230
[  188.513874]  vfs_write+0xdc/0x230
[  188.514698]  ksys_write+0xaf/0x140
[  188.515523]  do_syscall_64+0x5e/0x1a0
[  188.516543]  entry_SYSCALL_64_after_hwframe+0x44/0xa9
[  188.517710]
[  188.518034] The buggy address belongs to the object at ffff8881e9c26000
[  188.518034]  which belongs to the cache kmalloc-4k of size 4096
[  188.520528] The buggy address is located 8 bytes inside of
[  188.520528]  4096-byte region [ffff8881e9c26000, ffff8881e9c27000)
[  188.523015] The buggy address belongs to the page:
[  188.524357] page:ffffea0007a70800 refcount:1 mapcount:0 mapping:ffff8881f6402140 index:0x0 compound_mapcount: 0
[  188.527058] raw: 0200000000010200 dead000000000100 dead000000000122 ffff8881f6402140
[  188.528983] raw: 0000000000000000 0000000000040004 00000001ffffffff 0000000000000000
[  188.530883] page dumped because: kasan: bad access detected
[  188.532336]
[  188.532720] Memory state around the buggy address:
[  188.533871]  ffff8881e9c25f00: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[  188.535631]  ffff8881e9c25f80: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[  188.537370] >ffff8881e9c26000: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[  188.538996]                       ^
[  188.539812]  ffff8881e9c26080: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[  188.541549]  ffff8881e9c26100: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb

Signed-off-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: vimc: allocate vimc_device dynamically

In future patch, the release of the device will move
to the release callback of v4l2_device. Therefore the
device will be released only when the last fh will be
closed. Dynamic allocation will then be needed since
when the device is unbounded and then bounded again,
it might be that the probe callback will run before
the release of the last device is finished. In that
case both operations will run on the same memory
concurrently and cause memory corruption.
This patch also removes the pdev field of
vimc_device since it is not needed anymore.

Signed-off-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: vimc: replace vimc->pdev.dev with vimc->mdev.dev

replace 'vimc->pdev.dev' with 'vimc->mdev.dev'
in debug prints and in assignment to
vimc_ent_device.dev. This helps to unify the debug
statements. This will also eliminate the need to use
the pdev field in vimc_device in future patch.

Signed-off-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: Documentation:media:v4l-drivers: Update vivid documentation.

Add metadata capture/output and v4l-touch support in vivid
documentation.

Signed-off-by: Vandana BN <bnvandana@gmail.com>
[hverkuil-cisco@xs4all.nl: fixed some typos, made some small tweaks of the text]
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: rcar_drif: Do not print error in case of EPROBE_DEFER for dma channel

If the dma channel request error code is EPROBE_DEFER there is no need to
print error message.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: aspeed: add AST2600 support

Video engine in AST2600 has the exactly same register set with
AST2500 except VR084 register which provides more precise JPEG
size read back. This commit adds support for the difference and
adds 'aspeed,ast2600-video-engine' compatible OF string.

Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: staging: rkisp1: capture: remove support to userptr memory

VB2_USERPTR support doesn't make sense for drivers based on
vb2_dma_contig, so just drop it.

Otherwise, queues using vb2_dma_contig_memops causes v4l2-compliance
to fail for VB2_USERPTR mode, due to buffer misalignment.

Signed-off-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
Acked-by: Helen Koike <helen.koike@collabora.com>
[hverkuil-cisco@xs4all.nl: replaced commit log with Helen's suggestion]
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: videobuf2-core.h: improve buf_struct_size documentation

Explicitly document that the driver-specific buffer structure
must start with the subsystem-specific struct (vb2_v4l2_buffer
in the case of V4L2).

Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: staging: rkisp1: remove serialization item in the TODO file

The item 'Fix serialization on subdev ops.' was solved,
so remove it from the TODO file.

Signed-off-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
Acked-by: Helen Koike <helen.koike@collabora.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: videobuf2-dma-contig.c: remove spurious 'b' in message

Remove a spurious 'b' in the "contiguous chunk is too small  %lu/%lu b"
message.

Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: mtk-vcodec: reset segment data then trig decoder

VP9 bitstream specification indicate segment data should reset to
default when meet key frames, intra only frames or enable error
resilience mode. So memset segmentation map buffer before every
decode process is not appropriate.

Reset segment data only when needed, then start decoder hardware

Signed-off-by: Rui Wang <gtk_ruiwang@mediatek.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: dt-bindings: media: Add Allwinner A64 deinterlace compatible

Allwinner A64 SoC also contains deinterlace core, compatible to H3.

Add compatible string for it.

Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: go7007: Fix URB type for interrupt handling

Josef reported that his old-and-good Plextor ConvertX M402U video
converter spews lots of WARNINGs on the recent kernels, and it turned
out that the device uses a bulk endpoint for interrupt handling just
like 2250 board.

For fixing it, generalize the check with the proper verification of
the endpoint instead of hard-coded board type check.

Fixes: 7e5219d18e93 ("[media] go7007: Fix 2250 urb type")
Reported-and-tested-by: Josef Möllers <josef.moellers@suse.com>
BugLink: https://bugzilla.suse.com/show_bug.cgi?id=1162583
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=206427
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: sun8i: Add Allwinner A83T Rotate driver

Allwinner A83T contains rotation core which can rotate and flip images.

Add a driver for it.

Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
[hverkuil-cisco@xs4all.nl: MAINTAINERS paths were out of date, fix that]
[hverkuil-cisco@xs4all.nl: VFL_TYPE_GRABBER -> _VIDEO]
[hverkuil-cisco@xs4all.nl: Fix module build]
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: dt-bindings: media: Add Allwinner A83T Rotate driver

Some Allwinner SoCs like A83T and A64 contain rotate core which can
rotate and flip images.

Add a binding for it.

Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: Split v4l2_pipeline_pm_use into v4l2_pipeline_pm_{get, put}

Currently, v4l2_pipeline_pm_use() prototype is:

  int v4l2_pipeline_pm_use(struct media_entity *entity, int use)

Where the 'use' argument shall only be set to '1' for enable/power-on,
or to '0' for disable/power-off. The integer return is specified
as only meaningful when 'use' is set to '1'.

Let's enforce this semantic by splitting the function in two:
v4l2_pipeline_pm_get and v4l2_pipeline_pm_put. This is done
for several reasons.

It makes the API easier to use (or harder to misuse).
It removes the constraint on the values the 'use' argument
shall take. Also, it removes the need to constraint
the return value, by making v4l2_pipeline_pm_put void return.

And last, it's more consistent with other kernel APIs, such
as the runtime pm APIs, which makes the code more symmetric.

Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: usbvision: deprecate driver

The driver is deprecated and scheduled for removal by the end
of 2020. The reason is that this driver is for old and obsolete
hardware, and it produces a continuous stream of syzbot errors due
to poor code.

In order to prevent removal the following actions would have to
be taken:

- clean up the code
- convert to the vb2 framework
- fix the disconnect and free-on-last-user handling (i.e., add
  a release callback for struct v4l2_device and rework the code
  to use that correctly).

Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: uapi: h264: Add DPB entry field reference flags

Using the field information attached to v4l2 buffers is not enough to
determine the type of field referenced by a DPB entry: the decoded
frame might contain the full picture (both top and bottom fields)
but the reference only point to one of them.
Let's add new V4L2_H264_DPB_ENTRY_FLAG_ flags to express that.

[Keep only 2 flags and add some details about they mean]

Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: rtl28xxu: add missing sleep before probing slave demod

Slave demod needs some time to wake up otherwise it may not respond to the
following probe commands. This problem manifested randomly on my Astrometa
DVB-T2 dongle.

Signed-off-by: Mario Hros <git@reversity.org>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: arm64: dts: amlogic: add rc-videostrong-kii-pro keymap

videostrong kii pro comes with a nec rc, add the keymap to the dts

Signed-off-by: Mohammad Rasim <mohammad.rasim96@gmail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: dt-bindings: media: add new kii pro key map

Add new entry for rc-videostrong-kii-pro in linux,rc-map-name

Signed-off-by: Mohammad Rasim <mohammad.rasim96@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: rc: iguanair: Replace zero-length array with flexible-array member

The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:

struct foo {
        int stuff;
        struct boo array[];
};

By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.

This issue was found with the help of Coccinelle.

[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 76497732932f ("cxgb3/l2t: Fix undefined behaviour")

Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: rc: fix spelling mistake "to" -> "too"

There is a spelling mistake in a dev_dbg message. Fix it.

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: vsp1: tidyup VI6_HGT_LBn_H() macro

The address of VSP2_VI6_HGT_LBx_H are
VSP2_VI6_HGT_LB0_H : 0x3428
VSP2_VI6_HGT_LB1_H : 0x3430
VSP2_VI6_HGT_LB2_H : 0x3438
VSP2_VI6_HGT_LB3_H : 0x3440

Thus, VI6_HGT_LBn_H() macro should start from 0x3420 instead of 0x3430.
This patch fixes it.

Fixes: 26e0ca22c3b8 ("[media] v4l: Renesas R-Car VSP1 driver")

Reported-by: Koji Matsuoka <koji.matsuoka.xm@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: smiapp: Move definitions under driver directory

include/media/i2c/smiapp.h was meant to serve systems where the sensor is
enumerated through platform data. That's no longer necessary, hopefully
not even in out-of-tree use cases. Move the definitions to the appropriate
headers.

Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: smiapp: Refactor reading SMIA limits

Combine the two trivial functions reading limits into one. Also rename
smiapp_get_all_limits() as smiapp_read_all_smia_limits().

Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: smiapp: Move SMIA limit reading up

Move SMIA limit reading up, where other limit and capability handling
takes place.

Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: smiapp: Turn limit lookup into a function

Instead of direct array access, turn accessing limit information into a
function. Going forward, more elaborate CCS limits will replace most SMIA
limits, and conversion will be less complicated this way.

Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: smiapp: Use unaligned get and put functions

Use get_unaligned_be* and put_unaligned_be* functions to convert register
values to CPU endianness. Consequently, two instances of BUG() are
removed.

Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: smiapp: Simplify condition for choosing 8-bit access

Use the only8 boolean to determine whether 8-bit access is required for
reading.

Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: omap3isp: Prevent enabling CCDC when stopping streaming

Commit ... prevented restarting CCDC through its interrupt handler when
it's about to be disabled. It missed to address the case when CCDC might
be enabled due to queueing a buffer. Do that now.

Fixes: dd12ed17ce9e ("omap3isp: Don't restart CCDC if we're about to stop")

Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: MAINTAINERS: Sort entries in database for TI VPE/CAL

Run parse-maintainers.pl and choose TI VPE/CAL record. Fix it accordingly.

Note, this is urgent fix, without which parse-maintainers.pl throws
an exception:

Odd non-pattern line '  Documentation/devicetree/bindings/media/ti,cal.yaml
' for 'TI VPE/CAL DRIVERS' at scripts/parse-maintainers.pl line 147, <$file> line 16770.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: staging: media: ipu3: Change 'unsigned long int' to 'unsigned long'

This patch fixes the checkpatch.pl warning:

WARNING: Prefer 'unsigned long' over 'unsigned long int' as the int is
unnecessary

Signed-off-by: Jean-Baptiste Jouband <jj.jouband@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: i2c: Add driver for Sony IMX219 sensor

Adds a driver for the 8MPix Sony IMX219 CSI2 sensor.
Whilst the sensor supports 2 or 4 CSI2 data lanes, this driver
currently only supports 2 lanes.
8MPix @ 15fps, 1080P @ 30fps (cropped FOV), and 1640x1232 (2x2 binned)
@ 30fps are currently supported.

[Sakari Ailus: make imx219_check_hwcfg static]

Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Andrey Konovalov <andrey.konovalov@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: dt-bindings: media: i2c: Add IMX219 CMOS sensor binding

Add YAML device tree binding for IMX219 CMOS image sensor, and
the relevant MAINTAINERS entries.

Signed-off-by: Andrey Konovalov <andrey.konovalov@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: ipu3.rst: add imgu pipe config tool link

A specific tool which can be used to generate imgu intermedia
resolutions now is public on github, this patch adds this information
into ipu3.rst.

Signed-off-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: ov5675: add vflip/hflip control support

- Add V4L2 controls: horizontal/vertical flip,
  keep SGRBG10 Bayer order output (via change v/hflip)
- Fix Bayer order output in 1296x972 binning registers

Signed-off-by: Shawn Tu <shawnx.tu@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: dt-bindings: media: venus: Add sc7180 DT schema

Add new qcom,sc7180-venus DT binding schema.

Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dikshita Agarwal <dikshita@codeaurora.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: venus: core: add sc7180 DT compatible and resource struct

This add DT compatible string and resource structure for sc7180.

Signed-off-by: Dikshita Agarwal <dikshita@codeaurora.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: dt-bindings: media: venus: delete old binding document

After transitioning to YAML DT schema we don't need this old-style
document.

Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: venus: core: add sdm845-v2 DT compatible and resource struct

In order to use dynamic video codec assignment add a new sdm845-v2
DT compatible and new venus_resource structure to cover the binding
where all pmdomains and clocks are under the venus_core control.

Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: dt-bindings: media: venus: Add sdm845v2 DT schema

Add new qcom,sdm845-venus-v2 DT binding schema.

Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: dt-bindings: media: venus: Convert sdm845 to DT schema

Convert qcom,sdm845-venus Venus binding to DT schema.

Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>