hwmon: (lm90) Introduce flag indicating extended temperature support

[ Upstream commit f347e249fcf920ad6974cbd898e2ec0b366a1c34 ]

A flag indicating extended temperature support makes it easier
to add support for additional chips with this functionality.

Cc: David T. Wilson <david.wilson@nasa.gov>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

hwmon: (lm90) Add basic support for TI TMP461

[ Upstream commit f8344f7693a25d9025a59d164450b50c6f5aa3c0 ]

TMP461 is almost identical to TMP451 and was actually detected as TMP451
with the existing lm90 driver if its I2C address is 0x4c. Add support
for it to the lm90 driver. At the same time, improve the chip detection
function to at least try to distinguish between TMP451 and TMP461.

As a side effect, this fixes commit 24333ac26d01 ("hwmon: (tmp401) use
smb word operations instead of 2 smb byte operations"). TMP461 does not
support word operations on temperature registers, which causes bad
temperature readings with the tmp401 driver. The lm90 driver does not
perform word operations on temperature registers and thus does not have
this problem.

Support is listed as basic because TMP461 supports a sensor resolution
of 0.0625 degrees C, while the lm90 driver assumes a resolution of 0.125
degrees C. Also, the TMP461 supports negative temperatures with its
default temperature range, which is not the case for similar chips
supported by the lm90 and the tmp401 drivers. Those limitations will be
addressed with follow-up patches.

Fixes: 24333ac26d01 ("hwmon: (tmp401) use smb word operations instead of 2 smb byte operations")
Reported-by: David T. Wilson <david.wilson@nasa.gov>
Cc: David T. Wilson <david.wilson@nasa.gov>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

hwmon: (lm90) Fix usage of CONFIG2 register in detect function

[ Upstream commit fce15c45d3fbd9fc1feaaf3210d8e3f8b33dfd3a ]

The detect function had a comment "Make compiler happy" when id did not
read the second configuration register. As it turns out, the code was
checking the contents of this register for manufacturer ID 0xA1 (NXP
Semiconductor/Philips), but never actually read the register. So it
wasn't surprising that the compiler complained, and it indeed had a point.
Fix the code to read the register contents for manufacturer ID 0xa1.

At the same time, the code was reading the register for manufacturer ID
0x41 (Analog Devices), but it was not using the results. In effect it was
just checking if reading the register returned an error. That doesn't
really add much if any value, so stop doing that.

Fixes: f90be42fb383 ("hwmon: (lm90) Refactor reading of config2 register")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

pinctrl: bcm2835: Change init order for gpio hogs

[ Upstream commit 266423e60ea1b953fcc0cd97f3dad85857e434d1 ]

...and gpio-ranges

pinctrl-bcm2835 is a combined pinctrl/gpio driver. Currently the gpio
side is registered first, but this breaks gpio hogs (which are
configured during gpiochip_add_data). Part of the hog initialisation
is a call to pinctrl_gpio_request, and since the pinctrl driver hasn't
yet been registered this results in an -EPROBE_DEFER from which it can
never recover.

Change the initialisation sequence to register the pinctrl driver
first.

This also solves a similar problem with the gpio-ranges property, which
is required in order for released pins to be returned to inputs.

Fixes: 73345a18d464b ("pinctrl: bcm2835: Pass irqchip when adding gpiochip")
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20211206092237.4105895-2-phil@raspberrypi.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

Input: elantech - fix stack out of bound access in elantech_change_report_id()

[ Upstream commit 1d72d9f960ccf1052a0630a68c3d358791dbdaaa ]

The array param[] in elantech_change_report_id() must be at least 3
bytes, because elantech_read_reg_params() is calling ps2_command() with
PSMOUSE_CMD_GETINFO, that is going to access 3 bytes from param[], but
it's defined in the stack as an array of 2 bytes, therefore we have a
potential stack out-of-bounds access here, also confirmed by KASAN:

[    6.512374] BUG: KASAN: stack-out-of-bounds in __ps2_command+0x372/0x7e0
[    6.512397] Read of size 1 at addr ffff8881024d77c2 by task kworker/2:1/118

[    6.512416] CPU: 2 PID: 118 Comm: kworker/2:1 Not tainted 5.13.0-22-generic #22+arighi20211110
[    6.512428] Hardware name: LENOVO 20T8000QGE/20T8000QGE, BIOS R1AET32W (1.08 ) 08/14/2020
[    6.512436] Workqueue: events_long serio_handle_event
[    6.512453] Call Trace:
[    6.512462]  show_stack+0x52/0x58
[    6.512474]  dump_stack+0xa1/0xd3
[    6.512487]  print_address_description.constprop.0+0x1d/0x140
[    6.512502]  ? __ps2_command+0x372/0x7e0
[    6.512516]  __kasan_report.cold+0x7d/0x112
[    6.512527]  ? _raw_write_lock_irq+0x20/0xd0
[    6.512539]  ? __ps2_command+0x372/0x7e0
[    6.512552]  kasan_report+0x3c/0x50
[    6.512564]  __asan_load1+0x6a/0x70
[    6.512575]  __ps2_command+0x372/0x7e0
[    6.512589]  ? ps2_drain+0x240/0x240
[    6.512601]  ? dev_printk_emit+0xa2/0xd3
[    6.512612]  ? dev_vprintk_emit+0xc5/0xc5
[    6.512621]  ? __kasan_check_write+0x14/0x20
[    6.512634]  ? mutex_lock+0x8f/0xe0
[    6.512643]  ? __mutex_lock_slowpath+0x20/0x20
[    6.512655]  ps2_command+0x52/0x90
[    6.512670]  elantech_ps2_command+0x4f/0xc0 [psmouse]
[    6.512734]  elantech_change_report_id+0x1e6/0x256 [psmouse]
[    6.512799]  ? elantech_report_trackpoint.constprop.0.cold+0xd/0xd [psmouse]
[    6.512863]  ? ps2_command+0x7f/0x90
[    6.512877]  elantech_query_info.cold+0x6bd/0x9ed [psmouse]
[    6.512943]  ? elantech_setup_ps2+0x460/0x460 [psmouse]
[    6.513005]  ? psmouse_reset+0x69/0xb0 [psmouse]
[    6.513064]  ? psmouse_attr_set_helper+0x2a0/0x2a0 [psmouse]
[    6.513122]  ? phys_pmd_init+0x30e/0x521
[    6.513137]  elantech_init+0x8a/0x200 [psmouse]
[    6.513200]  ? elantech_init_ps2+0xf0/0xf0 [psmouse]
[    6.513249]  ? elantech_query_info+0x440/0x440 [psmouse]
[    6.513296]  ? synaptics_send_cmd+0x60/0x60 [psmouse]
[    6.513342]  ? elantech_query_info+0x440/0x440 [psmouse]
[    6.513388]  ? psmouse_try_protocol+0x11e/0x170 [psmouse]
[    6.513432]  psmouse_extensions+0x65d/0x6e0 [psmouse]
[    6.513476]  ? psmouse_try_protocol+0x170/0x170 [psmouse]
[    6.513519]  ? mutex_unlock+0x22/0x40
[    6.513526]  ? ps2_command+0x7f/0x90
[    6.513536]  ? psmouse_probe+0xa3/0xf0 [psmouse]
[    6.513580]  psmouse_switch_protocol+0x27d/0x2e0 [psmouse]
[    6.513624]  psmouse_connect+0x272/0x530 [psmouse]
[    6.513669]  serio_driver_probe+0x55/0x70
[    6.513679]  really_probe+0x190/0x720
[    6.513689]  driver_probe_device+0x160/0x1f0
[    6.513697]  device_driver_attach+0x119/0x130
[    6.513705]  ? device_driver_attach+0x130/0x130
[    6.513713]  __driver_attach+0xe7/0x1a0
[    6.513720]  ? device_driver_attach+0x130/0x130
[    6.513728]  bus_for_each_dev+0xfb/0x150
[    6.513738]  ? subsys_dev_iter_exit+0x10/0x10
[    6.513748]  ? _raw_write_unlock_bh+0x30/0x30
[    6.513757]  driver_attach+0x2d/0x40
[    6.513764]  serio_handle_event+0x199/0x3d0
[    6.513775]  process_one_work+0x471/0x740
[    6.513785]  worker_thread+0x2d2/0x790
[    6.513794]  ? process_one_work+0x740/0x740
[    6.513802]  kthread+0x1b4/0x1e0
[    6.513809]  ? set_kthread_struct+0x80/0x80
[    6.513816]  ret_from_fork+0x22/0x30

[    6.513832] The buggy address belongs to the page:
[    6.513838] page:00000000bc35e189 refcount:0 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x1024d7
[    6.513847] flags: 0x17ffffc0000000(node=0|zone=2|lastcpupid=0x1fffff)
[    6.513860] raw: 0017ffffc0000000 dead000000000100 dead000000000122 0000000000000000
[    6.513867] raw: 0000000000000000 0000000000000000 00000000ffffffff 0000000000000000
[    6.513872] page dumped because: kasan: bad access detected

[    6.513879] addr ffff8881024d77c2 is located in stack of task kworker/2:1/118 at offset 34 in frame:
[    6.513887]  elantech_change_report_id+0x0/0x256 [psmouse]

[    6.513941] this frame has 1 object:
[    6.513947]  [32, 34) 'param'

[    6.513956] Memory state around the buggy address:
[    6.513962]  ffff8881024d7680: f2 f2 f2 f2 f2 00 00 f3 f3 00 00 00 00 00 00 00
[    6.513969]  ffff8881024d7700: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[    6.513976] >ffff8881024d7780: 00 00 00 00 f1 f1 f1 f1 02 f3 f3 f3 00 00 00 00
[    6.513982]                                            ^
[    6.513988]  ffff8881024d7800: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[    6.513995]  ffff8881024d7880: 00 f1 f1 f1 f1 03 f2 03 f2 03 f3 f3 f3 00 00 00
[    6.514000] ==================================================================

Define param[] in elantech_change_report_id() as an array of 3 bytes to
prevent the out-of-bounds access in the stack.

Fixes: e4c9062717fe ("Input: elantech - fix protocol errors for some trackpoints in SMBus mode")
BugLink: https://bugs.launchpad.net/bugs/1945590
Signed-off-by: Andrea Righi <andrea.righi@canonical.com>
Reviewed-by: Wolfram Sang <wsa@kernel.org>
Link: https://lore.kernel.org/r/20211116095559.24395-1-andrea.righi@canonical.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

sfc: falcon: Check null pointer of rx_queue->page_ring

[ Upstream commit 9b8bdd1eb5890aeeab7391dddcf8bd51f7b07216 ]

Because of the possible failure of the kcalloc, it should be better to
set rx_queue->page_ptr_mask to 0 when it happens in order to maintain
the consistency.

Fixes: 5a6681e22c14 ("sfc: separate out SFC4000 ("Falcon") support into new sfc-falcon driver")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Acked-by: Martin Habets <habetsm.xilinx@gmail.com>
Link: https://lore.kernel.org/r/20211220140344.978408-1-jiasheng@iscas.ac.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

sfc: Check null pointer of rx_queue->page_ring

[ Upstream commit bdf1b5c3884f6a0dc91b0dbdb8c3b7d205f449e0 ]

Because of the possible failure of the kcalloc, it should be better to
set rx_queue->page_ptr_mask to 0 when it happens in order to maintain
the consistency.

Fixes: 5a6681e22c14 ("sfc: separate out SFC4000 ("Falcon") support into new sfc-falcon driver")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Acked-by: Martin Habets <habetsm.xilinx@gmail.com>
Link: https://lore.kernel.org/r/20211220135603.954944-1-jiasheng@iscas.ac.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: ks8851: Check for error irq

[ Upstream commit 99d7fbb5cedf598f67e8be106d6c7b8d91366aef ]

Because platform_get_irq() could fail and return error irq.
Therefore, it might be better to check it if order to avoid the use of
error irq.

Fixes: 797047f875b5 ("net: ks8851: Implement Parallel bus operations")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drivers: net: smc911x: Check for error irq

[ Upstream commit cb93b3e11d405f20a405a07482d01147ef4934a3 ]

Because platform_get_irq() could fail and return error irq.
Therefore, it might be better to check it if order to avoid the use of
error irq.

Fixes: ae150435b59e ("smsc: Move the SMC (SMSC) drivers")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

fjes: Check for error irq

[ Upstream commit db6d6afe382de5a65d6ccf51253ab48b8e8336c3 ]

I find that platform_get_irq() will not always succeed.
It will return error irq in case of the failure.
Therefore, it might be better to check it if order to avoid the use of
error irq.

Fixes: 658d439b2292 ("fjes: Introduce FUJITSU Extended Socket Network Device driver")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

bonding: fix ad_actor_system option setting to default

[ Upstream commit 1c15b05baea71a5ff98235783e3e4ad227760876 ]

When 802.3ad bond mode is configured the ad_actor_system option is set to
"00:00:00:00:00:00". But when trying to set the all-zeroes MAC as actors'
system address it was failing with EINVAL.

An all-zeroes ethernet address is valid, only multicast addresses are not
valid values.

Fixes: 171a42c38c6e ("bonding: add netlink support for sys prio, actor sys mac, and port key")
Signed-off-by: Fernando Fernandez Mancera <ffmancera@riseup.net>
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Link: https://lore.kernel.org/r/20211221111345.2462-1-ffmancera@riseup.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ipmi: Fix UAF when uninstall ipmi_si and ipmi_msghandler module

[ Upstream commit ffb76a86f8096a8206be03b14adda6092e18e275 ]

Hi,

When testing install and uninstall of ipmi_si.ko and ipmi_msghandler.ko,
the system crashed.

The log as follows:
[  141.087026] BUG: unable to handle kernel paging request at ffffffffc09b3a5a
[  141.087241] PGD 8fe4c0d067 P4D 8fe4c0d067 PUD 8fe4c0f067 PMD 103ad89067 PTE 0
[  141.087464] Oops: 0010 [#1] SMP NOPTI
[  141.087580] CPU: 67 PID: 668 Comm: kworker/67:1 Kdump: loaded Not tainted 4.18.0.x86_64 #47
[  141.088009] Workqueue: events 0xffffffffc09b3a40
[  141.088009] RIP: 0010:0xffffffffc09b3a5a
[  141.088009] Code: Bad RIP value.
[  141.088009] RSP: 0018:ffffb9094e2c3e88 EFLAGS: 00010246
[  141.088009] RAX: 0000000000000000 RBX: ffff9abfdb1f04a0 RCX: 0000000000000000
[  141.088009] RDX: 0000000000000000 RSI: 0000000000000246 RDI: 0000000000000246
[  141.088009] RBP: 0000000000000000 R08: ffff9abfffee3cb8 R09: 00000000000002e1
[  141.088009] R10: ffffb9094cb73d90 R11: 00000000000f4240 R12: ffff9abfffee8700
[  141.088009] R13: 0000000000000000 R14: ffff9abfdb1f04a0 R15: ffff9abfdb1f04a8
[  141.088009] FS:  0000000000000000(0000) GS:ffff9abfffec0000(0000) knlGS:0000000000000000
[  141.088009] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[  141.088009] CR2: ffffffffc09b3a30 CR3: 0000008fe4c0a001 CR4: 00000000007606e0
[  141.088009] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[  141.088009] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[  141.088009] PKRU: 55555554
[  141.088009] Call Trace:
[  141.088009]  ? process_one_work+0x195/0x390
[  141.088009]  ? worker_thread+0x30/0x390
[  141.088009]  ? process_one_work+0x390/0x390
[  141.088009]  ? kthread+0x10d/0x130
[  141.088009]  ? kthread_flush_work_fn+0x10/0x10
[  141.088009]  ? ret_from_fork+0x35/0x40] BUG: unable to handle kernel paging request at ffffffffc0b28a5a
[  200.223240] PGD 97fe00d067 P4D 97fe00d067 PUD 97fe00f067 PMD a580cbf067 PTE 0
[  200.223464] Oops: 0010 [#1] SMP NOPTI
[  200.223579] CPU: 63 PID: 664 Comm: kworker/63:1 Kdump: loaded Not tainted 4.18.0.x86_64 #46
[  200.224008] Workqueue: events 0xffffffffc0b28a40
[  200.224008] RIP: 0010:0xffffffffc0b28a5a
[  200.224008] Code: Bad RIP value.
[  200.224008] RSP: 0018:ffffbf3c8e2a3e88 EFLAGS: 00010246
[  200.224008] RAX: 0000000000000000 RBX: ffffa0799ad6bca0 RCX: 0000000000000000
[  200.224008] RDX: 0000000000000000 RSI: 0000000000000246 RDI: 0000000000000246
[  200.224008] RBP: 0000000000000000 R08: ffff9fe43fde3cb8 R09: 00000000000000d5
[  200.224008] R10: ffffbf3c8cb53d90 R11: 00000000000f4240 R12: ffff9fe43fde8700
[  200.224008] R13: 0000000000000000 R14: ffffa0799ad6bca0 R15: ffffa0799ad6bca8
[  200.224008] FS:  0000000000000000(0000) GS:ffff9fe43fdc0000(0000) knlGS:0000000000000000
[  200.224008] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[  200.224008] CR2: ffffffffc0b28a30 CR3: 00000097fe00a002 CR4: 00000000007606e0
[  200.224008] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[  200.224008] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[  200.224008] PKRU: 55555554
[  200.224008] Call Trace:
[  200.224008]  ? process_one_work+0x195/0x390
[  200.224008]  ? worker_thread+0x30/0x390
[  200.224008]  ? process_one_work+0x390/0x390
[  200.224008]  ? kthread+0x10d/0x130
[  200.224008]  ? kthread_flush_work_fn+0x10/0x10
[  200.224008]  ? ret_from_fork+0x35/0x40
[  200.224008] kernel fault(0x1) notification starting on CPU 63
[  200.224008] kernel fault(0x1) notification finished on CPU 63
[  200.224008] CR2: ffffffffc0b28a5a
[  200.224008] ---[ end trace c82a412d93f57412 ]---

The reason is as follows:
T1: rmmod ipmi_si.
    ->ipmi_unregister_smi()
        -> ipmi_bmc_unregister()
            -> __ipmi_bmc_unregister()
                -> kref_put(&bmc->usecount, cleanup_bmc_device);
                    -> schedule_work(&bmc->remove_work);

T2: rmmod ipmi_msghandler.
    ipmi_msghander module uninstalled, and the module space
    will be freed.

T3: bmc->remove_work doing cleanup the bmc resource.
    -> cleanup_bmc_work()
        -> platform_device_unregister(&bmc->pdev);
            -> platform_device_del(pdev);
                -> device_del(&pdev->dev);
                    -> kobject_uevent(&dev->kobj, KOBJ_REMOVE);
                        -> kobject_uevent_env()
                            -> dev_uevent()
                                -> if (dev->type && dev->type->name)

   'dev->type'(bmc_device_type) pointer space has freed when uninstall
    ipmi_msghander module, 'dev->type->name' cause the system crash.

drivers/char/ipmi/ipmi_msghandler.c:
2820 static const struct device_type bmc_device_type = {
2821         .groups         = bmc_dev_attr_groups,
2822 };

Steps to reproduce:
Add a time delay in cleanup_bmc_work() function,
and uninstall ipmi_si and ipmi_msghandler module.

2910 static void cleanup_bmc_work(struct work_struct *work)
2911 {
2912         struct bmc_device *bmc = container_of(work, struct bmc_device,
2913                                               remove_work);
2914         int id = bmc->pdev.id; /* Unregister overwrites id */
2915
2916         msleep(3000);   <---
2917         platform_device_unregister(&bmc->pdev);
2918         ida_simple_remove(&ipmi_bmc_ida, id);
2919 }

Use 'remove_work_wq' instead of 'system_wq' to solve this issues.

Fixes: b2cfd8ab4add ("ipmi: Rework device id and guid handling to catch changing BMCs")
Signed-off-by: Wu Bo <wubo40@huawei.com>
Message-Id: <1640070034-56671-1-git-send-email-wubo40@huawei.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

igb: fix deadlock caused by taking RTNL in RPM resume path

[ Upstream commit ac8c58f5b535d6272324e2b8b4a0454781c9147e ]

Recent net core changes caused an issue with few Intel drivers
(reportedly igb), where taking RTNL in RPM resume path results in a
deadlock. See [0] for a bug report. I don't think the core changes
are wrong, but taking RTNL in RPM resume path isn't needed.
The Intel drivers are the only ones doing this. See [1] for a
discussion on the issue. Following patch changes the RPM resume path
to not take RTNL.

[0] https://bugzilla.kernel.org/show_bug.cgi?id=215129
[1] https://lore.kernel.org/netdev/20211125074949.5f897431@kicinski-fedora-pc1c0hjn.dhcp.thefacebook.com/t/

Fixes: bd869245a3dc ("net: core: try to runtime-resume detached device in __dev_open")
Fixes: f32a21376573 ("ethtool: runtime-resume netdev parent before ethtool ioctl ops")
Tested-by: Martin Stolpe <martin.stolpe@gmail.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20211220201844.2714498-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: skip virtio_net_hdr_set_proto if protocol already set

[ Upstream commit 1ed1d592113959f00cc552c3b9f47ca2d157768f ]

virtio_net_hdr_set_proto infers skb->protocol from the virtio_net_hdr
gso_type, to avoid packets getting dropped for lack of a proto type.

Its protocol choice is a guess, especially in the case of UFO, where
the single VIRTIO_NET_HDR_GSO_UDP label covers both UFOv4 and UFOv6.

Skip this best effort if the field is already initialized. Whether
explicitly from userspace, or implicitly based on an earlier call to
dev_parse_header_protocol (which is more robust, but was introduced
after this patch).

Fixes: 9d2f67e43b73 ("net/packet: fix packet drop as of virtio gso")
Signed-off-by: Willem de Bruijn <willemb@google.com>
Link: https://lore.kernel.org/r/20211220145027.2784293-1-willemdebruijn.kernel@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: accept UFOv6 packages in virtio_net_hdr_to_skb

[ Upstream commit 7e5cced9ca84df52d874aca6b632f930b3dc5bc6 ]

Skb with skb->protocol 0 at the time of virtio_net_hdr_to_skb may have
a protocol inferred from virtio_net_hdr with virtio_net_hdr_set_proto.

Unlike TCP, UDP does not have separate types for IPv4 and IPv6. Type
VIRTIO_NET_HDR_GSO_UDP is guessed to be IPv4/UDP. As of the below
commit, UFOv6 packets are dropped due to not matching the protocol as
obtained from dev_parse_header_protocol.

Invert the test to take that L2 protocol field as starting point and
pass both UFOv4 and UFOv6 for VIRTIO_NET_HDR_GSO_UDP.

Fixes: 924a9bc362a5 ("net: check if protocol extracted by virtio_net_hdr_set_proto is correct")
Link: https://lore.kernel.org/netdev/CABcq3pG9GRCYqFDBAJ48H1vpnnX=41u+MhQnayF1ztLH4WX0Fw@mail.gmail.com/
Reported-by: Andrew Melnichenko <andrew@daynix.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Link: https://lore.kernel.org/r/20211220144901.2784030-1-willemdebruijn.kernel@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

qlcnic: potential dereference null pointer of rx_queue->page_ring

[ Upstream commit 60ec7fcfe76892a1479afab51ff17a4281923156 ]

The return value of kcalloc() needs to be checked.
To avoid dereference of null pointer in case of the failure of alloc.
Therefore, it might be better to change the return type of
qlcnic_sriov_alloc_vlans() and return -ENOMEM when alloc fails and
return 0 the others.
Also, qlcnic_sriov_set_guest_vlan_mode() and __qlcnic_pci_sriov_enable()
should deal with the return value of qlcnic_sriov_alloc_vlans().

Fixes: 154d0c810c53 ("qlcnic: VLAN enhancement for 84XX adapters")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: marvell: prestera: fix incorrect return of port_find

[ Upstream commit 8b681bd7c301c423fbe97a6b23388a2180ff04ca ]

In case, when some ports is in list and we don't find requested - we
return last iterator state and not return NULL as expected.

Fixes: 501ef3066c89 ("net: marvell: prestera: Add driver for Prestera family ASIC devices")
Signed-off-by: Yevhen Orlov <yevhen.orlov@plvision.eu>
Link: https://lore.kernel.org/r/20211216170736.8851-1-yevhen.orlov@plvision.eu
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ARM: dts: imx6qdl-wandboard: Fix Ethernet support

[ Upstream commit 39e660687ac0c57499134765abbecf71cfd11eae ]

Currently, the imx6q-wandboard Ethernet does not transmit any
data.

This issue has been exposed by commit f5d9aa79dfdf ("ARM: imx6q:
remove clk-out fixup for the Atheros AR8031 and AR8035 PHYs").

Fix it by describing the qca,clk-out-frequency property as suggested
by the commit above.

Fixes: 77591e42458d ("ARM: dts: imx6qdl-wandboard: add ethernet PHY description")
Signed-off-by: Martin Haaß <vvvrrooomm@gmail.com>
Tested-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

netfilter: fix regression in looped (broad|multi)cast's MAC handling

[ Upstream commit ebb966d3bdfed581ecccbb4a7432341baf7619b4 ]

In commit 5648b5e1169f ("netfilter: nfnetlink_queue: fix OOB when mac
header was cleared"), the test for non-empty MAC header introduced in
commit 2c38de4c1f8da7 ("netfilter: fix looped (broad|multi)cast's MAC
handling") has been replaced with a test for a set MAC header.

This breaks the case when the MAC header has been reset (using
skb_reset_mac_header), as is the case with looped-back multicast
packets.  As a result, the packets ending up in NFQUEUE get a bogus
hwaddr interpreted from the first bytes of the IP header.

This patch adds a test for a non-empty MAC header in addition to the
test for a set MAC header.  The same two tests are also implemented in
nfnetlink_log.c, where the initial code of commit 2c38de4c1f8da7
("netfilter: fix looped (broad|multi)cast's MAC handling") has not been
touched, but where supposedly the same situation may happen.

Fixes: 5648b5e1169f ("netfilter: nfnetlink_queue: fix OOB when mac header was cleared")
Signed-off-by: Ignacy Gawędzki <ignacy.gawedzki@green-communications.fr>
Reviewed-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

RDMA/hns: Replace kfree() with kvfree()

[ Upstream commit 12d3bbdd6bd2780b71cc466f3fbc6eb7d43bbc2a ]

Variables allocated by kvmalloc_array() should not be freed by kfree.
Because they may be allocated by vmalloc.  So we replace kfree() with
kvfree() here.

Fixes: 6fd610c5733d ("RDMA/hns: Support 0 hop addressing for SRQ buffer")
Link: https://lore.kernel.org/r/20211210094234.5829-1-billsjc@sjtu.edu.cn
Signed-off-by: Jiacheng Shi <billsjc@sjtu.edu.cn>
Acked-by: Wenpeng Liang <liangwenpeng@huawei.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

IB/qib: Fix memory leak in qib_user_sdma_queue_pkts()

[ Upstream commit bee90911e0138c76ee67458ac0d58b38a3190f65 ]

The wrong goto label was used for the error case and missed cleanup of the
pkt allocation.

Fixes: d39bf40e55e6 ("IB/qib: Protect from buffer overflow in struct qib_user_sdma_pkt fields")
Link: https://lore.kernel.org/r/20211208175238.29983-1-jose.exposito89@gmail.com
Addresses-Coverity-ID: 1493352 ("Resource leak")
Signed-off-by: José Expósito <jose.exposito89@gmail.com>
Acked-by: Mike Marciniszyn <mike.marciniszyn@cornelisnetworks.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ASoC: meson: aiu: fifo: Add missing dma_coerce_mask_and_coherent()

[ Upstream commit 1bcd326631dc4faa3322d60b4fc45e8b3747993e ]

The FIFO registers which take an DMA-able address are only 32-bit wide
on AIU. Add dma_coerce_mask_and_coherent() to make the DMA core aware of
this limitation.

Fixes: 6ae9ca9ce986bf ("ASoC: meson: aiu: add i2s and spdif support")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20211206210804.2512999-2-martin.blumenstingl@googlemail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

spi: change clk_disable_unprepare to clk_unprepare

[ Upstream commit db6689b643d8653092f5853751ea2cdbc299f8d3 ]

The corresponding API for clk_prepare is clk_unprepare, other than
clk_disable_unprepare.

Fix this by changing clk_disable_unprepare to clk_unprepare.

Fixes: 5762ab71eb24 ("spi: Add support for Armada 3700 SPI Controller")
Signed-off-by: Dongliang Mu <mudongliangabcd@gmail.com>
Link: https://lore.kernel.org/r/20211206101931.2816597-1-mudongliangabcd@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

arm64: dts: allwinner: orangepi-zero-plus: fix PHY mode

[ Upstream commit 08d2061ff9c5319a07bf9ca6bbf11fdec68f704a ]

Orange Pi Zero Plus uses a Realtek RTL8211E RGMII Gigabit PHY, but its
currently set to plain RGMII mode meaning that it doesn't introduce
delays.

With this setup, TX packets are completely lost and changing the mode to
RGMII-ID so the PHY will add delays internally fixes the issue.

Fixes: a7affb13b271 ("arm64: allwinner: H5: Add Xunlong Orange Pi Zero Plus")
Acked-by: Chen-Yu Tsai <wens@csie.org>
Tested-by: Ron Goossens <rgoossens@gmail.com>
Tested-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20211117140222.43692-1-robert.marko@sartura.hr
Signed-off-by: Sasha Levin <sashal@kernel.org>

HID: potential dereference of null pointer

commit 13251ce1dd9bb525da2becb9b26fdfb94ca58659 upstream.

The return value of devm_kzalloc() needs to be checked.
To avoid hdev->dev->driver_data to be null in case of the failure of
alloc.

Fixes: 14c9c014babe ("HID: add vivaldi HID driver")
Cc: stable@vger.kernel.org
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Link: https://lore.kernel.org/r/20211215083605.117638-1-jiasheng@iscas.ac.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

HID: holtek: fix mouse probing

commit 93a2207c254ca102ebbdae47b00f19bbfbfa7ecd upstream.

An overlook from the previous commit: we don't even parse or start the
device, meaning that the device is not presented to user space.

Fixes: 93020953d0fa ("HID: check for valid USB device for many HID drivers")
Cc: stable@vger.kernel.org
Link: https://bugs.archlinux.org/task/73048
Link: https://bugzilla.kernel.org/show_bug.cgi?id=215341
Link: https://lore.kernel.org/r/e4efbf13-bd8d-0370-629b-6c80c0044b15@leemhuis.info/
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ext4: check for inconsistent extents between index and leaf block

commit 9c6e071913792d80894cd0be98cc3c4b770e26d3 upstream.

Now that we can check out overlapping extents in leaf block and
out-of-order index extents in index block. But the .ee_block in the
first extent of one leaf block should equal to the .ei_block in it's
parent index extent entry. This patch add a check to verify such
inconsistent between the index and leaf block.

Signed-off-by: Zhang Yi <yi.zhang@huawei.com>
Link: https://lore.kernel.org/r/20210908120850.4012324-3-yi.zhang@huawei.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ext4: check for out-of-order index extents in ext4_valid_extent_entries()

commit 8dd27fecede55e8a4e67eef2878040ecad0f0d33 upstream.

After commit 5946d089379a ("ext4: check for overlapping extents in
ext4_valid_extent_entries()"), we can check out the overlapping extent
entry in leaf extent blocks. But the out-of-order extent entry in index
extent blocks could also trigger bad things if the filesystem is
inconsistent. So this patch add a check to figure out the out-of-order
index extents and return error.

Signed-off-by: Zhang Yi <yi.zhang@huawei.com>
Reviewed-by: Theodore Ts'o <tytso@mit.edu>
Link: https://lore.kernel.org/r/20210908120850.4012324-2-yi.zhang@huawei.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ext4: prevent partial update of the extent blocks

commit 0f2f87d51aebcf71a709b52f661d681594c7dffa upstream.

In the most error path of current extents updating operations are not
roll back partial updates properly when some bad things happens(.e.g in
ext4_ext_insert_extent()). So we may get an inconsistent extents tree
if journal has been aborted due to IO error, which may probability lead
to BUGON later when we accessing these extent entries in errors=continue
mode. This patch drop extent buffer's verify flag before updatng the
contents in ext4_ext_get_access(), and reset it after updating in
__ext4_ext_dirty(). After this patch we could force to check the extent
buffer if extents tree updating was break off, make sure the extents are
consistent.

Signed-off-by: Zhang Yi <yi.zhang@huawei.com>
Reviewed-by: Theodore Ts'o <tytso@mit.edu>
Link: https://lore.kernel.org/r/20210908120850.4012324-4-yi.zhang@huawei.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: usb: lan78xx: add Allied Telesis AT29M2-AF

commit ef8a0f6eab1ca5d1a75c242c5c7b9d386735fa0a upstream.

This adds the vendor and product IDs for the AT29M2-AF which is a
lan7801-based device.

Signed-off-by: Greg Jesionowski <jesionowskigreg@gmail.com>
Link: https://lore.kernel.org/r/20211214221027.305784-1-jesionowskigreg@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

arm64: vdso32: require CROSS_COMPILE_COMPAT for gcc+bfd

commit 3e6f8d1fa18457d54b20917bd9174d27daf09ab9 upstream.

Similar to
commit 231ad7f409f1 ("Makefile: infer --target from ARCH for CC=clang")
There really is no point in setting --target based on
$CROSS_COMPILE_COMPAT for clang when the integrated assembler is being
used, since
commit ef94340583ee ("arm64: vdso32: drop -no-integrated-as flag").

Allows COMPAT_VDSO to be selected without setting $CROSS_COMPILE_COMPAT
when using clang and lld together.

Before:
$ ARCH=arm64 CROSS_COMPILE_COMPAT=arm-linux-gnueabi- make -j72 LLVM=1 defconfig
$ grep CONFIG_COMPAT_VDSO .config
CONFIG_COMPAT_VDSO=y
$ ARCH=arm64 make -j72 LLVM=1 defconfig
$ grep CONFIG_COMPAT_VDSO .config
$

After:
$ ARCH=arm64 CROSS_COMPILE_COMPAT=arm-linux-gnueabi- make -j72 LLVM=1 defconfig
$ grep CONFIG_COMPAT_VDSO .config
CONFIG_COMPAT_VDSO=y
$ ARCH=arm64 make -j72 LLVM=1 defconfig
$ grep CONFIG_COMPAT_VDSO .config
CONFIG_COMPAT_VDSO=y

Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Suggested-by: Nathan Chancellor <nathan@kernel.org>
Tested-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Link: https://lore.kernel.org/r/20211019223646.1146945-5-ndesaulniers@google.com
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

arm64: vdso32: drop -no-integrated-as flag

commit ef94340583eec5cb1544dc41a87baa4f684b3fe1 upstream.

Clang can assemble these files just fine; this is a relic from the top
level Makefile conditionally adding this. We no longer need --prefix,
--gcc-toolchain, or -Qunused-arguments flags either with this change, so
remove those too.

To test building:
$ ARCH=arm64 CROSS_COMPILE=aarch64-linux-gnu- \
  CROSS_COMPILE_COMPAT=arm-linux-gnueabi- make LLVM=1 LLVM_IAS=1 \
  defconfig arch/arm64/kernel/vdso32/

Suggested-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Tested-by: Stephen Boyd <swboyd@chromium.org>
Acked-by: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20210420174427.230228-1-ndesaulniers@google.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Linux 5.10.88

Link: https://lore.kernel.org/r/20211220143029.352940568@linuxfoundation.org
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Salvatore Bonaccorso <carnil@debian.org>
Tested-by: Shuah Khan <skhan@linuxfoundation.org>
Tested-by: Hulk Robot <hulkrobot@huawei.com>
Tested-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Tested-by: Linux Kernel Functional Testing <lkft@linaro.org>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

xen/netback: don't queue unlimited number of packages

commit be81992f9086b230623ae3ebbc85ecee4d00a3d3 upstream.

In case a guest isn't consuming incoming network traffic as fast as it
is coming in, xen-netback is buffering network packages in unlimited
numbers today. This can result in host OOM situations.

Commit f48da8b14d04ca8 ("xen-netback: fix unlimited guest Rx internal
queue and carrier flapping") meant to introduce a mechanism to limit
the amount of buffered data by stopping the Tx queue when reaching the
data limit, but this doesn't work for cases like UDP.

When hitting the limit don't queue further SKBs, but drop them instead.
In order to be able to tell Rx packages have been dropped increment the
rx_dropped statistics counter in this case.

It should be noted that the old solution to continue queueing SKBs had
the additional problem of an overflow of the 32-bit rx_queue_len value
would result in intermittent Tx queue enabling.

This is part of XSA-392

Fixes: f48da8b14d04ca8 ("xen-netback: fix unlimited guest Rx internal queue and carrier flapping")
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

xen/netback: fix rx queue stall detection

commit 6032046ec4b70176d247a71836186d47b25d1684 upstream.

Commit 1d5d48523900a4b ("xen-netback: require fewer guest Rx slots when
not using GSO") introduced a security problem in netback, as an
interface would only be regarded to be stalled if no slot is available
in the rx queue ring page. In case the SKB at the head of the queued
requests will need more than one rx slot and only one slot is free the
stall detection logic will never trigger, as the test for that is only
looking for at least one slot to be free.

Fix that by testing for the needed number of slots instead of only one
slot being available.

In order to not have to take the rx queue lock that often, store the
number of needed slots in the queue data. As all SKB dequeue operations
happen in the rx queue kernel thread this is safe, as long as the
number of needed slots is accessed via READ/WRITE_ONCE() only and
updates are always done with the rx queue lock held.

Add a small helper for obtaining the number of free slots.

This is part of XSA-392

Fixes: 1d5d48523900a4b ("xen-netback: require fewer guest Rx slots when not using GSO")
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

xen/console: harden hvc_xen against event channel storms

commit fe415186b43df0db1f17fa3a46275fd92107fe71 upstream.

The Xen console driver is still vulnerable for an attack via excessive
number of events sent by the backend. Fix that by using a lateeoi event
channel.

For the normal domU initial console this requires the introduction of
bind_evtchn_to_irq_lateeoi() as there is no xenbus device available
at the time the event channel is bound to the irq.

As the decision whether an interrupt was spurious or not requires to
test for bytes having been read from the backend, move sending the
event into the if statement, as sending an event without having found
any bytes to be read is making no sense at all.

This is part of XSA-391

Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

xen/netfront: harden netfront against event channel storms

commit b27d47950e481f292c0a5ad57357edb9d95d03ba upstream.

The Xen netfront driver is still vulnerable for an attack via excessive
number of events sent by the backend. Fix that by using lateeoi event
channels.

For being able to detect the case of no rx responses being added while
the carrier is down a new lock is needed in order to update and test
rsp_cons and the number of seen unconsumed responses atomically.

This is part of XSA-391

Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

xen/blkfront: harden blkfront against event channel storms

commit 0fd08a34e8e3b67ec9bd8287ac0facf8374b844a upstream.

The Xen blkfront driver is still vulnerable for an attack via excessive
number of events sent by the backend. Fix that by using lateeoi event
channels.

This is part of XSA-391

Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Revert "xsk: Do not sleep in poll() when need_wakeup set"

commit 0706a78f31c4217ca144f630063ec9561a21548d upstream.

This reverts commit bd0687c18e635b63233dc87f38058cd728802ab4.

This patch causes a Tx only workload to go to sleep even when it does
not have to, leading to misserable performance in skb mode. It fixed
one rare problem but created a much worse one, so this need to be
reverted while I try to craft a proper solution to the original
problem.

Fixes: bd0687c18e63 ("xsk: Do not sleep in poll() when need_wakeup set")
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20211217145646.26449-1-magnus.karlsson@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

bus: ti-sysc: Fix variable set but not used warning for reinit_modules

commit 1b1da99b845337362a3dafe0f7b49927ab4ae041 upstream.

Fix drivers/bus/ti-sysc.c:2494:13: error: variable 'error' set but not
used introduced by commit 9d881361206e ("bus: ti-sysc: Add quirk handling
for reinit on context lost").

Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

rcu: Mark accesses to rcu_state.n_force_qs

commit 2431774f04d1050292054c763070021bade7b151 upstream.

This commit marks accesses to the rcu_state.n_force_qs.  These data
races are hard to make happen, but syzkaller was equal to the task.

Reported-by: syzbot+e08a83a1940ec3846cd5@syzkaller.appspotmail.com
Acked-by: Marco Elver <elver@google.com>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

scsi: scsi_debug: Sanity check block descriptor length in resp_mode_select()

commit e0a2c28da11e2c2b963fc01d50acbf03045ac732 upstream.

In resp_mode_select() sanity check the block descriptor len to avoid UAF.

BUG: KASAN: use-after-free in resp_mode_select+0xa4c/0xb40 drivers/scsi/scsi_debug.c:2509
Read of size 1 at addr ffff888026670f50 by task scsicmd/15032

CPU: 1 PID: 15032 Comm: scsicmd Not tainted 5.15.0-01d0625 #15
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS
Call Trace:
 <TASK>
 dump_stack_lvl+0x89/0xb5 lib/dump_stack.c:107
 print_address_description.constprop.9+0x28/0x160 mm/kasan/report.c:257
 kasan_report.cold.14+0x7d/0x117 mm/kasan/report.c:443
 __asan_report_load1_noabort+0x14/0x20 mm/kasan/report_generic.c:306
 resp_mode_select+0xa4c/0xb40 drivers/scsi/scsi_debug.c:2509
 schedule_resp+0x4af/0x1a10 drivers/scsi/scsi_debug.c:5483
 scsi_debug_queuecommand+0x8c9/0x1e70 drivers/scsi/scsi_debug.c:7537
 scsi_queue_rq+0x16b4/0x2d10 drivers/scsi/scsi_lib.c:1521
 blk_mq_dispatch_rq_list+0xb9b/0x2700 block/blk-mq.c:1640
 __blk_mq_sched_dispatch_requests+0x28f/0x590 block/blk-mq-sched.c:325
 blk_mq_sched_dispatch_requests+0x105/0x190 block/blk-mq-sched.c:358
 __blk_mq_run_hw_queue+0xe5/0x150 block/blk-mq.c:1762
 __blk_mq_delay_run_hw_queue+0x4f8/0x5c0 block/blk-mq.c:1839
 blk_mq_run_hw_queue+0x18d/0x350 block/blk-mq.c:1891
 blk_mq_sched_insert_request+0x3db/0x4e0 block/blk-mq-sched.c:474
 blk_execute_rq_nowait+0x16b/0x1c0 block/blk-exec.c:63
 sg_common_write.isra.18+0xeb3/0x2000 drivers/scsi/sg.c:837
 sg_new_write.isra.19+0x570/0x8c0 drivers/scsi/sg.c:775
 sg_ioctl_common+0x14d6/0x2710 drivers/scsi/sg.c:941
 sg_ioctl+0xa2/0x180 drivers/scsi/sg.c:1166
 __x64_sys_ioctl+0x19d/0x220 fs/ioctl.c:52
 do_syscall_64+0x3a/0x80 arch/x86/entry/common.c:50
 entry_SYSCALL_64_after_hwframe+0x44/0xae arch/x86/entry/entry_64.S:113

Link: https://lore.kernel.org/r/1637262208-28850-1-git-send-email-george.kennedy@oracle.com
Reported-by: syzkaller <syzkaller@googlegroups.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: George Kennedy <george.kennedy@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

scsi: scsi_debug: Fix type in min_t to avoid stack OOB

commit 36e07d7ede88a1f1ef8f0f209af5b7612324ac2c upstream.

Change min_t() to use type "u32" instead of type "int" to avoid stack out
of bounds. With min_t() type "int" the values get sign extended and the
larger value gets used causing stack out of bounds.

BUG: KASAN: stack-out-of-bounds in memcpy include/linux/fortify-string.h:191 [inline]
BUG: KASAN: stack-out-of-bounds in sg_copy_buffer+0x1de/0x240 lib/scatterlist.c:976
Read of size 127 at addr ffff888072607128 by task syz-executor.7/18707

CPU: 1 PID: 18707 Comm: syz-executor.7 Not tainted 5.15.0-syzk #1
Hardware name: Red Hat KVM, BIOS 1.13.0-2
Call Trace:
 __dump_stack lib/dump_stack.c:88 [inline]
 dump_stack_lvl+0x89/0xb5 lib/dump_stack.c:106
 print_address_description.constprop.9+0x28/0x160 mm/kasan/report.c:256
 __kasan_report mm/kasan/report.c:442 [inline]
 kasan_report.cold.14+0x7d/0x117 mm/kasan/report.c:459
 check_region_inline mm/kasan/generic.c:183 [inline]
 kasan_check_range+0x1a3/0x210 mm/kasan/generic.c:189
 memcpy+0x23/0x60 mm/kasan/shadow.c:65
 memcpy include/linux/fortify-string.h:191 [inline]
 sg_copy_buffer+0x1de/0x240 lib/scatterlist.c:976
 sg_copy_from_buffer+0x33/0x40 lib/scatterlist.c:1000
 fill_from_dev_buffer.part.34+0x82/0x130 drivers/scsi/scsi_debug.c:1162
 fill_from_dev_buffer drivers/scsi/scsi_debug.c:1888 [inline]
 resp_readcap16+0x365/0x3b0 drivers/scsi/scsi_debug.c:1887
 schedule_resp+0x4d8/0x1a70 drivers/scsi/scsi_debug.c:5478
 scsi_debug_queuecommand+0x8c9/0x1ec0 drivers/scsi/scsi_debug.c:7533
 scsi_dispatch_cmd drivers/scsi/scsi_lib.c:1520 [inline]
 scsi_queue_rq+0x16b0/0x2d40 drivers/scsi/scsi_lib.c:1699
 blk_mq_dispatch_rq_list+0xb9b/0x2700 block/blk-mq.c:1639
 __blk_mq_sched_dispatch_requests+0x28f/0x590 block/blk-mq-sched.c:325
 blk_mq_sched_dispatch_requests+0x105/0x190 block/blk-mq-sched.c:358
 __blk_mq_run_hw_queue+0xe5/0x150 block/blk-mq.c:1761
 __blk_mq_delay_run_hw_queue+0x4f8/0x5c0 block/blk-mq.c:1838
 blk_mq_run_hw_queue+0x18d/0x350 block/blk-mq.c:1891
 blk_mq_sched_insert_request+0x3db/0x4e0 block/blk-mq-sched.c:474
 blk_execute_rq_nowait+0x16b/0x1c0 block/blk-exec.c:62
 sg_common_write.isra.18+0xeb3/0x2000 drivers/scsi/sg.c:836
 sg_new_write.isra.19+0x570/0x8c0 drivers/scsi/sg.c:774
 sg_ioctl_common+0x14d6/0x2710 drivers/scsi/sg.c:939
 sg_ioctl+0xa2/0x180 drivers/scsi/sg.c:1165
 vfs_ioctl fs/ioctl.c:51 [inline]
 __do_sys_ioctl fs/ioctl.c:874 [inline]
 __se_sys_ioctl fs/ioctl.c:860 [inline]
 __x64_sys_ioctl+0x19d/0x220 fs/ioctl.c:860
 do_syscall_x64 arch/x86/entry/common.c:50 [inline]
 do_syscall_64+0x3a/0x80 arch/x86/entry/common.c:80
 entry_SYSCALL_64_after_hwframe+0x44/0xae

Link: https://lore.kernel.org/r/1636484247-21254-1-git-send-email-george.kennedy@oracle.com
Reported-by: syzkaller <syzkaller@googlegroups.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: George Kennedy <george.kennedy@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

scsi: scsi_debug: Don't call kcalloc() if size arg is zero

commit 3344b58b53a76199dae48faa396e9fc37bf86992 upstream.

If the size arg to kcalloc() is zero, it returns ZERO_SIZE_PTR.  Because of
that, for a following NULL pointer check to work on the returned pointer,
kcalloc() must not be called with the size arg equal to zero. Return early
without error before the kcalloc() call if size arg is zero.

BUG: KASAN: null-ptr-deref in memcpy include/linux/fortify-string.h:191 [inline]
BUG: KASAN: null-ptr-deref in sg_copy_buffer+0x138/0x240 lib/scatterlist.c:974
Write of size 4 at addr 0000000000000010 by task syz-executor.1/22789

CPU: 1 PID: 22789 Comm: syz-executor.1 Not tainted 5.15.0-syzk #1
Hardware name: Red Hat KVM, BIOS 1.13.0-2
Call Trace:
 __dump_stack lib/dump_stack.c:88 [inline]
 dump_stack_lvl+0x89/0xb5 lib/dump_stack.c:106
 __kasan_report mm/kasan/report.c:446 [inline]
 kasan_report.cold.14+0x112/0x117 mm/kasan/report.c:459
 check_region_inline mm/kasan/generic.c:183 [inline]
 kasan_check_range+0x1a3/0x210 mm/kasan/generic.c:189
 memcpy+0x3b/0x60 mm/kasan/shadow.c:66
 memcpy include/linux/fortify-string.h:191 [inline]
 sg_copy_buffer+0x138/0x240 lib/scatterlist.c:974
 do_dout_fetch drivers/scsi/scsi_debug.c:2954 [inline]
 do_dout_fetch drivers/scsi/scsi_debug.c:2946 [inline]
 resp_verify+0x49e/0x930 drivers/scsi/scsi_debug.c:4276
 schedule_resp+0x4d8/0x1a70 drivers/scsi/scsi_debug.c:5478
 scsi_debug_queuecommand+0x8c9/0x1ec0 drivers/scsi/scsi_debug.c:7533
 scsi_dispatch_cmd drivers/scsi/scsi_lib.c:1520 [inline]
 scsi_queue_rq+0x16b0/0x2d40 drivers/scsi/scsi_lib.c:1699
 blk_mq_dispatch_rq_list+0xb9b/0x2700 block/blk-mq.c:1639
 __blk_mq_sched_dispatch_requests+0x28f/0x590 block/blk-mq-sched.c:325
 blk_mq_sched_dispatch_requests+0x105/0x190 block/blk-mq-sched.c:358
 __blk_mq_run_hw_queue+0xe5/0x150 block/blk-mq.c:1761
 __blk_mq_delay_run_hw_queue+0x4f8/0x5c0 block/blk-mq.c:1838
 blk_mq_run_hw_queue+0x18d/0x350 block/blk-mq.c:1891
 blk_mq_sched_insert_request+0x3db/0x4e0 block/blk-mq-sched.c:474
 blk_execute_rq_nowait+0x16b/0x1c0 block/blk-exec.c:62
 blk_execute_rq+0xdb/0x360 block/blk-exec.c:102
 sg_scsi_ioctl drivers/scsi/scsi_ioctl.c:621 [inline]
 scsi_ioctl+0x8bb/0x15c0 drivers/scsi/scsi_ioctl.c:930
 sg_ioctl_common+0x172d/0x2710 drivers/scsi/sg.c:1112
 sg_ioctl+0xa2/0x180 drivers/scsi/sg.c:1165
 vfs_ioctl fs/ioctl.c:51 [inline]
 __do_sys_ioctl fs/ioctl.c:874 [inline]
 __se_sys_ioctl fs/ioctl.c:860 [inline]
 __x64_sys_ioctl+0x19d/0x220 fs/ioctl.c:860
 do_syscall_x64 arch/x86/entry/common.c:50 [inline]
 do_syscall_64+0x3a/0x80 arch/x86/entry/common.c:80
 entry_SYSCALL_64_after_hwframe+0x44/0xae

Link: https://lore.kernel.org/r/1636056397-13151-1-git-send-email-george.kennedy@oracle.com
Reported-by: syzkaller <syzkaller@googlegroups.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: George Kennedy <george.kennedy@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ovl: fix warning in ovl_create_real()

commit 1f5573cfe7a7056e80a92c7a037a3e69f3a13d1c upstream.

Syzbot triggered the following warning in ovl_workdir_create() ->
ovl_create_real():

if (!err && WARN_ON(!newdentry->d_inode)) {

The reason is that the cgroup2 filesystem returns from mkdir without
instantiating the new dentry.

Weird filesystems such as this will be rejected by overlayfs at a later
stage during setup, but to prevent such a warning, call ovl_mkdir_real()
directly from ovl_workdir_create() and reject this case early.

Reported-and-tested-by: syzbot+75eab84fd0af9e8bf66b@syzkaller.appspotmail.com
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

fuse: annotate lock in fuse_reverse_inval_entry()

commit bda9a71980e083699a0360963c0135657b73f47a upstream.

Add missing inode lock annotatation; found by syzbot.

Reported-and-tested-by: syzbot+9f747458f5990eaa8d43@syzkaller.appspotmail.com
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

media: mxl111sf: change mutex_init() location

commit 44870a9e7a3c24acbb3f888b2a7cc22c9bdf7e7f upstream.

Syzbot reported, that mxl111sf_ctrl_msg() uses uninitialized
mutex. The problem was in wrong mutex_init() location.

Previous mutex_init(&state->msg_lock) call was in ->init() function, but
dvb_usbv2_init() has this order of calls:

dvb_usbv2_init()
  dvb_usbv2_adapter_init()
    dvb_usbv2_adapter_frontend_init()
      props->frontend_attach()

  props->init()

Since mxl111sf_* devices call mxl111sf_ctrl_msg() in ->frontend_attach()
internally we need to initialize state->msg_lock before
frontend_attach(). To achieve it, ->probe() call added to all mxl111sf_*
devices, which will simply initiaize mutex.

Reported-and-tested-by: syzbot+5ca0bf339f13c4243001@syzkaller.appspotmail.com
Fixes: 8572211842af ("[media] mxl111sf: convert to new DVB USB")
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

xsk: Do not sleep in poll() when need_wakeup set

commit bd0687c18e635b63233dc87f38058cd728802ab4 upstream.

Do not sleep in poll() when the need_wakeup flag is set. When this
flag is set, the application needs to explicitly wake up the driver
with a syscall (poll, recvmsg, sendmsg, etc.) to guarantee that Rx
and/or Tx processing will be processed promptly. But the current code
in poll(), sleeps first then wakes up the driver. This means that no
driver processing will occur (baring any interrupts) until the timeout
has expired.

Fix this by checking the need_wakeup flag first and if set, wake the
driver and return to the application. Only if need_wakeup is not set
should the process sleep if there is a timeout set in the poll() call.

Fixes: 77cd0d7b3f25 ("xsk: add support for need_wakeup flag in AF_XDP rings")
Reported-by: Keith Wiles <keith.wiles@intel.com>
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Link: https://lore.kernel.org/bpf/20211214102607.7677-1-magnus.karlsson@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ARM: dts: imx6ull-pinfunc: Fix CSI_DATA07__ESAI_TX0 pad name

commit 737e65c7956795b3553781fb7bc82fce1c39503f upstream.

According to the i.MX6ULL Reference Manual, pad CSI_DATA07 may
have the ESAI_TX0 functionality, not ESAI_T0.

Also, NXP's i.MX Config Tools 10.0 generates dtsi with the
MX6ULL_PAD_CSI_DATA07__ESAI_TX0 naming, so fix it accordingly.

There are no devicetree users in mainline that use the old name,
so just remove the old entry.

Fixes: c201369d4aa5 ("ARM: dts: imx6ull: add imx6ull support")
Reported-by: George Makarov <georgemakarov1@gmail.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Input: touchscreen - avoid bitwise vs logical OR warning

commit a02dcde595f7cbd240ccd64de96034ad91cffc40 upstream.

A new warning in clang points out a few places in this driver where a
bitwise OR is being used with boolean types:

drivers/input/touchscreen.c:81:17: warning: use of bitwise '|' with boolean operands [-Wbitwise-instead-of-logical]
        data_present = touchscreen_get_prop_u32(dev, "touchscreen-min-x",
                       ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

This use of a bitwise OR is intentional, as bitwise operations do not
short circuit, which allows all the calls to touchscreen_get_prop_u32()
to happen so that the last parameter is initialized while coalescing the
results of the calls to make a decision after they are all evaluated.

To make this clearer to the compiler, use the '|=' operator to assign
the result of each touchscreen_get_prop_u32() call to data_present,
which keeps the meaning of the code the same but makes it obvious that
every one of these calls is expected to happen.

Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reported-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Link: https://lore.kernel.org/r/20211014205757.3474635-1-nathan@kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/amdgpu: correct register access for RLC_JUMP_TABLE_RESTORE

commit f3a8076eb28cae1553958c629aecec479394bbe2 upstream.

should count on GC IP base address

Signed-off-by: Le Ma <le.ma@amd.com>
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

libata: if T_LENGTH is zero, dma direction should be DMA_NONE

commit 5da5231bb47864e5dd6c6731151e98b6ee498827 upstream.

Avoid data corruption by rejecting pass-through commands where
T_LENGTH is zero (No data is transferred) and the dma direction
is not DMA_NONE.

Cc: <stable@vger.kernel.org>
Reported-by: syzkaller<syzkaller@googlegroups.com>
Signed-off-by: George Kennedy<george.kennedy@oracle.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

timekeeping: Really make sure wall_to_monotonic isn't positive

commit 4e8c11b6b3f0b6a283e898344f154641eda94266 upstream.

Even after commit e1d7ba873555 ("time: Always make sure wall_to_monotonic
isn't positive") it is still possible to make wall_to_monotonic positive
by running the following code:

    int main(void)
    {
        struct timespec time;

        clock_gettime(CLOCK_MONOTONIC, &time);
        time.tv_nsec = 0;
        clock_settime(CLOCK_REALTIME, &time);
        return 0;
    }

The reason is that the second parameter of timespec64_compare(), ts_delta,
may be unnormalized because the delta is calculated with an open coded
substraction which causes the comparison of tv_sec to yield the wrong
result:

  wall_to_monotonic = { .tv_sec = -10, .tv_nsec =  900000000 }
  ts_delta      = { .tv_sec =  -9, .tv_nsec = -900000000 }

That makes timespec64_compare() claim that wall_to_monotonic < ts_delta,
but actually the result should be wall_to_monotonic > ts_delta.

After normalization, the result of timespec64_compare() is correct because
the tv_sec comparison is not longer misleading:

  wall_to_monotonic = { .tv_sec = -10, .tv_nsec =  900000000 }
  ts_delta      = { .tv_sec = -10, .tv_nsec =  100000000 }

Use timespec64_sub() to ensure that ts_delta is normalized, which fixes the
issue.

Fixes: e1d7ba873555 ("time: Always make sure wall_to_monotonic isn't positive")
Signed-off-by: Yu Liao <liaoyu15@huawei.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20211213135727.1656662-1-liaoyu15@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

serial: 8250_fintek: Fix garbled text for console

commit 6c33ff728812aa18792afffaf2c9873b898e7512 upstream.

Commit fab8a02b73eb ("serial: 8250_fintek: Enable high speed mode on Fintek F81866")
introduced support to use high baudrate with Fintek SuperIO UARTs. It'll
change clocksources when the UART probed.

But when user add kernel parameter "console=ttyS0,115200 console=tty0" to make
the UART as console output, the console will output garbled text after the
following kernel message.

[    3.681188] Serial: 8250/16550 driver, 32 ports, IRQ sharing enabled

The issue is occurs in following step:
probe_setup_port() -> fintek_8250_goto_highspeed()

It change clocksource from 115200 to 921600 with wrong time, it should change
clocksource in set_termios() not in probed. The following 3 patches are
implemented change clocksource in fintek_8250_set_termios().

Commit 58178914ae5b ("serial: 8250_fintek: UART dynamic clocksource on Fintek F81216H")
Commit 195638b6d44f ("serial: 8250_fintek: UART dynamic clocksource on Fintek F81866")
Commit 423d9118c624 ("serial: 8250_fintek: Add F81966 Support")

Due to the high baud rate had implemented above 3 patches and the patch
Commit fab8a02b73eb ("serial: 8250_fintek: Enable high speed mode on Fintek F81866")
is bugged, So this patch will remove it.

Fixes: fab8a02b73eb ("serial: 8250_fintek: Enable high speed mode on Fintek F81866")
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Link: https://lore.kernel.org/r/20211215075835.2072-1-hpeter+linux_kernel@gmail.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iocost: Fix divide-by-zero on donation from low hweight cgroup

commit edaa26334c117a584add6053f48d63a988d25a6e upstream.

The donation calculation logic assumes that the donor has non-zero
after-donation hweight, so the lowest active hweight a donating cgroup can
have is 2 so that it can donate 1 while keeping the other 1 for itself.
Earlier, we only donated from cgroups with sizable surpluses so this
condition was always true. However, with the precise donation algorithm
implemented, f1de2439ec43 ("blk-iocost: revamp donation amount
determination") made the donation amount calculation exact enabling even low
hweight cgroups to donate.

This means that in rare occasions, a cgroup with active hweight of 1 can
enter donation calculation triggering the following warning and then a
divide-by-zero oops.

 WARNING: CPU: 4 PID: 0 at block/blk-iocost.c:1928 transfer_surpluses.cold+0x0/0x53 [884/94867]
 ...
 RIP: 0010:transfer_surpluses.cold+0x0/0x53
 Code: 92 ff 48 c7 c7 28 d1 ab b5 65 48 8b 34 25 00 ae 01 00 48 81 c6 90 06 00 00 e8 8b 3f fe ff 48 c7 c0 ea ff ff ff e9 95 ff 92 ff <0f> 0b 48 c7 c7 30 da ab b5 e8 71 3f fe ff 4c 89 e8 4d 85 ed 74 0
4
 ...
 Call Trace:
  <IRQ>
  ioc_timer_fn+0x1043/0x1390
  call_timer_fn+0xa1/0x2c0
  __run_timers.part.0+0x1ec/0x2e0
  run_timer_softirq+0x35/0x70
 ...
 iocg: invalid donation weights in /a/b: active=1 donating=1 after=0

Fix it by excluding cgroups w/ active hweight < 2 from donating. Excluding
these extreme low hweight donations shouldn't affect work conservation in
any meaningful way.

Signed-off-by: Tejun Heo <tj@kernel.org>
Fixes: f1de2439ec43 ("blk-iocost: revamp donation amount determination")
Cc: stable@vger.kernel.org # v5.10+
Link: https://lore.kernel.org/r/Ybfh86iSvpWKxhVM@slm.duckdns.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

zonefs: add MODULE_ALIAS_FS

commit 8ffea2599f63fdbee968b894eab78170abf3ec2c upstream.

Add MODULE_ALIAS_FS() to load the module automatically when you do "mount
-t zonefs".

Fixes: 8dcc1a9d90c1 ("fs: New zonefs file system")
Cc: stable <stable@vger.kernel.org> # 5.6+
Signed-off-by: Naohiro Aota <naohiro.aota@wdc.com>
Reviewed-by: Johannes Thumshirn <jth@kernel.org>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

btrfs: fix double free of anon_dev after failure to create subvolume

commit 33fab972497ae66822c0b6846d4f9382938575b6 upstream.

When creating a subvolume, at create_subvol(), we allocate an anonymous
device and later call btrfs_get_new_fs_root(), which in turn just calls
btrfs_get_root_ref(). There we call btrfs_init_fs_root() which assigns
the anonymous device to the root, but if after that call there's an error,
when we jump to 'fail' label, we call btrfs_put_root(), which frees the
anonymous device and then returns an error that is propagated back to
create_subvol(). Than create_subvol() frees the anonymous device again.

When this happens, if the anonymous device was not reallocated after
the first time it was freed with btrfs_put_root(), we get a kernel
message like the following:

  (...)
  [13950.282466] BTRFS: error (device dm-0) in create_subvol:663: errno=-5 IO failure
  [13950.283027] ida_free called for id=65 which is not allocated.
  [13950.285974] BTRFS info (device dm-0): forced readonly
  (...)

If the anonymous device gets reallocated by another btrfs filesystem
or any other kernel subsystem, then bad things can happen.

So fix this by setting the root's anonymous device to 0 at
btrfs_get_root_ref(), before we call btrfs_put_root(), if an error
happened.

Fixes: 2dfb1e43f57dd3 ("btrfs: preallocate anon block device at first phase of snapshot creation")
CC: stable@vger.kernel.org # 5.10+
Reviewed-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

btrfs: fix memory leak in __add_inode_ref()

commit f35838a6930296fc1988764cfa54cb3f705c0665 upstream.

Line 1169 (#3) allocates a memory chunk for victim_name by kmalloc(),
but  when the function returns in line 1184 (#4) victim_name allocated
by line 1169 (#3) is not freed, which will lead to a memory leak.
There is a similar snippet of code in this function as allocating a memory
chunk for victim_name in line 1104 (#1) as well as releasing the memory
in line 1116 (#2).

We should kfree() victim_name when the return value of backref_in_log()
is less than zero and before the function returns in line 1184 (#4).

1057 static inline int __add_inode_ref(struct btrfs_trans_handle *trans,
1058    struct btrfs_root *root,
1059    struct btrfs_path *path,
1060    struct btrfs_root *log_root,
1061    struct btrfs_inode *dir,
1062    struct btrfs_inode *inode,
1063    u64 inode_objectid, u64 parent_objectid,
1064    u64 ref_index, char *name, int namelen,
1065    int *search_done)
1066 {

1104  victim_name = kmalloc(victim_name_len, GFP_NOFS);
// #1: kmalloc (victim_name-1)
1105  if (!victim_name)
1106  return -ENOMEM;

1112 ret = backref_in_log(log_root, &search_key,
1113 parent_objectid, victim_name,
1114 victim_name_len);
1115 if (ret < 0) {
1116 kfree(victim_name); // #2: kfree (victim_name-1)
1117 return ret;
1118 } else if (!ret) {

1169  victim_name = kmalloc(victim_name_len, GFP_NOFS);
// #3: kmalloc (victim_name-2)
1170  if (!victim_name)
1171  return -ENOMEM;

1180  ret = backref_in_log(log_root, &search_key,
1181  parent_objectid, victim_name,
1182  victim_name_len);
1183  if (ret < 0) {
1184  return ret; // #4: missing kfree (victim_name-2)
1185  } else if (!ret) {

1241  return 0;
1242 }

Fixes: d3316c8233bb ("btrfs: Properly handle backref_in_log retval")
CC: stable@vger.kernel.org # 5.10+
Reviewed-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Jianglei Nie <niejianglei2021@163.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: serial: option: add Telit FN990 compositions

commit 2b503c8598d1b232e7fc7526bce9326d92331541 upstream.

Add the following Telit FN990 compositions:

0x1070: tty, adb, rmnet, tty, tty, tty, tty
0x1071: tty, adb, mbim, tty, tty, tty, tty
0x1072: rndis, tty, adb, tty, tty, tty, tty
0x1073: tty, adb, ecm, tty, tty, tty, tty

Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Link: https://lore.kernel.org/r/20211210100714.22587-1-dnlplm@gmail.com
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: serial: cp210x: fix CP2105 GPIO registration

commit 83b67041f3eaf33f98a075249aa7f4c7617c2f85 upstream.

When generalising GPIO support and adding support for CP2102N, the GPIO
registration for some CP2105 devices accidentally broke. Specifically,
when all the pins of a port are in "modem" mode, and thus unavailable
for GPIO use, the GPIO chip would now be registered without having
initialised the number of GPIO lines. This would in turn be rejected by
gpiolib and some errors messages would be printed (but importantly probe
would still succeed).

Fix this by initialising the number of GPIO lines before registering the
GPIO chip.

Note that as for the other device types, and as when all CP2105 pins are
muxed for LED function, the GPIO chip is registered also when no pins
are available for GPIO use.

Reported-by: Maarten Brock <m.brock@vanmierlo.com>
Link: https://lore.kernel.org/r/5eb560c81d2ea1a2b4602a92d9f48a89@vanmierlo.com
Fixes: c8acfe0aadbe ("USB: serial: cp210x: implement GPIO support for CP2102N")
Cc: stable@vger.kernel.org # 4.19
Cc: Karoly Pados <pados@pados.hu>
Link: https://lore.kernel.org/r/20211126094348.31698-1-johan@kernel.org
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tested-by: Maarten Brock <m.brock@vanmierlo.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: xhci: Extend support for runtime power management for AMD's Yellow carp.

commit f886d4fbb7c97b8f5f447c92d2dab99c841803c0 upstream.

AMD's Yellow Carp platform has few more XHCI controllers,
enable the runtime power management support for the same.

Signed-off-by: Nehal Bakulchandra Shah <Nehal-Bakulchandra.shah@amd.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20211215093216.1839065-1-Nehal-Bakulchandra.shah@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

PCI/MSI: Mask MSI-X vectors only on success

commit 83dbf898a2d45289be875deb580e93050ba67529 upstream.

Masking all unused MSI-X entries is done to ensure that a crash kernel
starts from a clean slate, which correponds to the reset state of the
device as defined in the PCI-E specificion 3.0 and later:

 Vector Control for MSI-X Table Entries
 --------------------------------------

 "00: Mask bit:  When this bit is set, the function is prohibited from
                 sending a message using this MSI-X Table entry.
                 ...
                 This bit’s state after reset is 1 (entry is masked)."

A Marvell NVME device fails to deliver MSI interrupts after trying to
enable MSI-X interrupts due to that masking. It seems to take the MSI-X
mask bits into account even when MSI-X is disabled.

While not specification compliant, this can be cured by moving the masking
into the success path, so that the MSI-X table entries stay in device reset
state when the MSI-X setup fails.

[ tglx: Move it into the success path, add comment and amend changelog ]

Fixes: aa8092c1d1f1 ("PCI/MSI: Mask all unused MSI-X entries")
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-pci@vger.kernel.org
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Marek Vasut <marex@denx.de>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20211210161025.3287927-1-sr@denx.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

PCI/MSI: Clear PCI_MSIX_FLAGS_MASKALL on error

commit 94185adbfad56815c2c8401e16d81bdb74a79201 upstream.

PCI_MSIX_FLAGS_MASKALL is set in the MSI-X control register at MSI-X
interrupt setup time. It's cleared on success, but the error handling path
only clears the PCI_MSIX_FLAGS_ENABLE bit.

That's incorrect as the reset state of the PCI_MSIX_FLAGS_MASKALL bit is
zero. That can be observed via lspci:

        Capabilities: [b0] MSI-X: Enable- Count=67 Masked+

Clear the bit in the error path to restore the reset state.

Fixes: 438553958ba1 ("PCI/MSI: Enable and mask MSI-X early")
Reported-by: Stefan Roese <sr@denx.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Stefan Roese <sr@denx.de>
Cc: linux-pci@vger.kernel.org
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Marek Vasut <marex@denx.de>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/87tufevoqx.ffs@tglx
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: dwc2: fix STM ID/VBUS detection startup delay in dwc2_driver_probe

commit fac6bf87c55f7f0733efb0375565fb6a50cf2caf upstream.

When activate_stm_id_vb_detection is enabled, ID and Vbus detection relies
on sensing comparators. This detection needs time to stabilize.
A delay was already applied in dwc2_resume() when reactivating the
detection, but it wasn't done in dwc2_probe().
This patch adds delay after enabling STM ID/VBUS detection. Then, ID state
is good when initializing gadget and host, and avoid to get a wrong
Connector ID Status Change interrupt.

Fixes: a415083a11cc ("usb: dwc2: add support for STM32MP15 SoCs USB OTG HS and FS")
Cc: stable <stable@vger.kernel.org>
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Link: https://lore.kernel.org/r/20211207124510.268841-1-amelie.delaunay@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: NO_LPM quirk Lenovo USB-C to Ethernet Adapher(RTL8153-04)

commit 0ad3bd562bb91853b9f42bda145b5db6255aee90 upstream.

This device doesn't work well with LPM, losing connectivity intermittently.
Disable LPM to resolve the issue.

Reviewed-by: <markpearson@lenovo.com>
Signed-off-by: Jimmy Wang <wangjm221@gmail.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20211214012652.4898-1-wangjm221@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tty: n_hdlc: make n_hdlc_tty_wakeup() asynchronous

commit 1ee33b1ca2b8dabfcc17198ffd049a6b55674a86 upstream.

syzbot is reporting that an unprivileged user who logged in from tty
console can crash the system using a reproducer shown below [1], for
n_hdlc_tty_wakeup() is synchronously calling n_hdlc_send_frames().

----------
  #include <sys/ioctl.h>
  #include <unistd.h>

  int main(int argc, char *argv[])
  {
    const int disc = 0xd;

    ioctl(1, TIOCSETD, &disc);
    while (1) {
      ioctl(1, TCXONC, 0);
      write(1, "", 1);
      ioctl(1, TCXONC, 1); /* Kernel panic - not syncing: scheduling while atomic */
    }
  }
----------

Linus suspected that "struct tty_ldisc"->ops->write_wakeup() must not
sleep, and Jiri confirmed it from include/linux/tty_ldisc.h. Thus, defer
n_hdlc_send_frames() from n_hdlc_tty_wakeup() to a WQ context like
net/nfc/nci/uart.c does.

Link: https://syzkaller.appspot.com/bug?extid=5f47a8cea6a12b77a876
Reported-by: syzbot <syzbot+5f47a8cea6a12b77a876@syzkaller.appspotmail.com>
Cc: stable <stable@vger.kernel.org>
Analyzed-by: Fabio M. De Francesco <fmdefrancesco@gmail.com>
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Confirmed-by: Jiri Slaby <jirislaby@kernel.org>
Reviewed-by: Fabio M. De Francesco <fmdefrancesco@gmail.com>
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Link: https://lore.kernel.org/r/40de8b7e-a3be-4486-4e33-1b1d1da452f8@i-love.sakura.ne.jp
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

KVM: x86: Drop guest CPUID check for host initiated writes to MSR_IA32_PERF_CAPABILITIES

[ Upstream commit 1aa2abb33a419090c7c87d4ae842a6347078ee12 ]

The ability to write to MSR_IA32_PERF_CAPABILITIES from the host should
not depend on guest visible CPUID entries, even if just to allow
creating/restoring guest MSRs and CPUIDs in any sequence.

Fixes: 27461da31089 ("KVM: x86/pmu: Support full width counting")
Suggested-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Message-Id: <20211216165213.338923-3-vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

Revert "usb: early: convert to readl_poll_timeout_atomic()"

[ Upstream commit c4d936efa46d8ea183df16c0f3fa4423327da51d ]

This reverts commit 796eed4b2342c9d6b26c958e92af91253a2390e1.

This change causes boot lockups when using "arlyprintk=xdbc" because
ktime can not be used at this point in time in the boot process.  Also,
it is not needed for very small delays like this.

Reported-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Reported-by: Peter Zijlstra <peterz@infradead.org>
Cc: Jann Horn <jannh@google.com>
Cc: Chunfeng Yun <chunfeng.yun@mediatek.com>
Fixes: 796eed4b2342 ("usb: early: convert to readl_poll_timeout_atomic()")
Link: https://lore.kernel.org/r/c2b5c9bb-1b75-bf56-3754-b5b18812d65e@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

USB: gadget: bRequestType is a bitfield, not a enum

[ Upstream commit f08adf5add9a071160c68bb2a61d697f39ab0758 ]

Szymon rightly pointed out that the previous check for the endpoint
direction in bRequestType was not looking at only the bit involved, but
rather the whole value.  Normally this is ok, but for some request
types, bits other than bit 8 could be set and the check for the endpoint
length could not stall correctly.

Fix that up by only checking the single bit.

Fixes: 153a2d7e3350 ("USB: gadget: detect too-big endpoint 0 requests")
Cc: Felipe Balbi <balbi@kernel.org>
Reported-by: Szymon Heidrich <szymon.heidrich@gmail.com>
Link: https://lore.kernel.org/r/20211214184621.385828-1-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

powerpc/85xx: Fix oops when CONFIG_FSL_PMC=n

[ Upstream commit 3dc709e518b47386e6af937eaec37bb36539edfd ]

When CONFIG_FSL_PMC is set to n, no value is assigned to cpu_up_prepare
in the mpc85xx_pm_ops structure. As a result, oops is triggered in
smp_85xx_start_cpu().

  smp: Bringing up secondary CPUs ...
  kernel tried to execute user page (0) - exploit attempt? (uid: 0)
  BUG: Unable to handle kernel instruction fetch (NULL pointer?)
  Faulting instruction address: 0x00000000
  Oops: Kernel access of bad area, sig: 11 [#1]
  ...
  NIP [00000000] 0x0
  LR [c0021d2c] smp_85xx_kick_cpu+0xe8/0x568
  Call Trace:
  [c1051da8] [c0021cb8] smp_85xx_kick_cpu+0x74/0x568 (unreliable)
  [c1051de8] [c0011460] __cpu_up+0xc0/0x228
  [c1051e18] [c0031bbc] bringup_cpu+0x30/0x224
  [c1051e48] [c0031f3c] cpu_up.constprop.0+0x180/0x33c
  [c1051e88] [c00322e8] bringup_nonboot_cpus+0x88/0xc8
  [c1051eb8] [c07e67bc] smp_init+0x30/0x78
  [c1051ed8] [c07d9e28] kernel_init_freeable+0x118/0x2a8
  [c1051f18] [c00032d8] kernel_init+0x14/0x124
  [c1051f38] [c0010278] ret_from_kernel_thread+0x14/0x1c

Fixes: c45361abb918 ("powerpc/85xx: fix timebase sync issue when CONFIG_HOTPLUG_CPU=n")
Reported-by: Martin Kennedy <hurricos@gmail.com>
Signed-off-by: Xiaoming Ni <nixiaoming@huawei.com>
Tested-by: Martin Kennedy <hurricos@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20211126041153.16926-1-nixiaoming@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

bpf, selftests: Fix racing issue in btf_skc_cls_ingress test

[ Upstream commit c2fcbf81c332b42382a0c439bfe2414a241e4f5b ]

The libbpf CI reported occasional failure in btf_skc_cls_ingress:

  test_syncookie:FAIL:Unexpected syncookie states gen_cookie:80326634 recv_cookie:0
  bpf prog error at line 97

"error at line 97" means the bpf prog cannot find the listening socket
when the final ack is received.  It then skipped processing
the syncookie in the final ack which then led to "recv_cookie:0".

The problem is the userspace program did not do accept() and went
ahead to close(listen_fd) before the kernel (and the bpf prog) had
a chance to process the final ack.

The fix is to add accept() call so that the userspace will wait for
the kernel to finish processing the final ack first before close()-ing
everything.

Fixes: 9a856cae2217 ("bpf: selftest: Add test_btf_skc_cls_ingress")
Reported-by: Andrii Nakryiko <andrii@kernel.org>
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20211216191630.466151-1-kafai@fb.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

sit: do not call ipip6_dev_free() from sit_init_net()

[ Upstream commit e28587cc491ef0f3c51258fdc87fbc386b1d4c59 ]

ipip6_dev_free is sit dev->priv_destructor, already called
by register_netdevice() if something goes wrong.

Alternative would be to make ipip6_dev_free() robust against
multiple invocations, but other drivers do not implement this
strategy.

syzbot reported:

dst_release underflow
WARNING: CPU: 0 PID: 5059 at net/core/dst.c:173 dst_release+0xd8/0xe0 net/core/dst.c:173
Modules linked in:
CPU: 1 PID: 5059 Comm: syz-executor.4 Not tainted 5.16.0-rc5-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
RIP: 0010:dst_release+0xd8/0xe0 net/core/dst.c:173
Code: 4c 89 f2 89 d9 31 c0 5b 41 5e 5d e9 da d5 44 f9 e8 1d 90 5f f9 c6 05 87 48 c6 05 01 48 c7 c7 80 44 99 8b 31 c0 e8 e8 67 29 f9 <0f> 0b eb 85 0f 1f 40 00 53 48 89 fb e8 f7 8f 5f f9 48 83 c3 a8 48
RSP: 0018:ffffc9000aa5faa0 EFLAGS: 00010246
RAX: d6894a925dd15a00 RBX: 00000000ffffffff RCX: 0000000000040000
RDX: ffffc90005e19000 RSI: 000000000003ffff RDI: 0000000000040000
RBP: 0000000000000000 R08: ffffffff816a1f42 R09: ffffed1017344f2c
R10: ffffed1017344f2c R11: 0000000000000000 R12: 0000607f462b1358
R13: 1ffffffff1bfd305 R14: ffffe8ffffcb1358 R15: dffffc0000000000
FS:  00007f66c71a2700(0000) GS:ffff8880b9a00000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f88aaed5058 CR3: 0000000023e0f000 CR4: 00000000003506f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
 <TASK>
 dst_cache_destroy+0x107/0x1e0 net/core/dst_cache.c:160
 ipip6_dev_free net/ipv6/sit.c:1414 [inline]
 sit_init_net+0x229/0x550 net/ipv6/sit.c:1936
 ops_init+0x313/0x430 net/core/net_namespace.c:140
 setup_net+0x35b/0x9d0 net/core/net_namespace.c:326
 copy_net_ns+0x359/0x5c0 net/core/net_namespace.c:470
 create_new_namespaces+0x4ce/0xa00 kernel/nsproxy.c:110
 unshare_nsproxy_namespaces+0x11e/0x180 kernel/nsproxy.c:226
 ksys_unshare+0x57d/0xb50 kernel/fork.c:3075
 __do_sys_unshare kernel/fork.c:3146 [inline]
 __se_sys_unshare kernel/fork.c:3144 [inline]
 __x64_sys_unshare+0x34/0x40 kernel/fork.c:3144
 do_syscall_x64 arch/x86/entry/common.c:50 [inline]
 do_syscall_64+0x44/0xd0 arch/x86/entry/common.c:80
 entry_SYSCALL_64_after_hwframe+0x44/0xae
RIP: 0033:0x7f66c882ce99
Code: ff ff c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 40 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 bc ff ff ff f7 d8 64 89 01 48
RSP: 002b:00007f66c71a2168 EFLAGS: 00000246 ORIG_RAX: 0000000000000110
RAX: ffffffffffffffda RBX: 00007f66c893ff60 RCX: 00007f66c882ce99
RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000048040200
RBP: 00007f66c8886ff1 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000000
R13: 00007fff6634832f R14: 00007f66c71a2300 R15: 0000000000022000
 </TASK>

Fixes: cf124db566e6 ("net: Fix inconsistent teardown and release of private netdev state.")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Link: https://lore.kernel.org/r/20211216111741.1387540-1-eric.dumazet@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: systemport: Add global locking for descriptor lifecycle

[ Upstream commit 8b8e6e782456f1ce02a7ae914bbd5b1053f0b034 ]

The descriptor list is a shared resource across all of the transmit queues, and
the locking mechanism used today only protects concurrency across a given
transmit queue between the transmit and reclaiming. This creates an opportunity
for the SYSTEMPORT hardware to work on corrupted descriptors if we have
multiple producers at once which is the case when using multiple transmit
queues.

This was particularly noticeable when using multiple flows/transmit queues and
it showed up in interesting ways in that UDP packets would get a correct UDP
header checksum being calculated over an incorrect packet length. Similarly TCP
packets would get an equally correct checksum computed by the hardware over an
incorrect packet length.

The SYSTEMPORT hardware maintains an internal descriptor list that it re-arranges
when the driver produces a new descriptor anytime it writes to the
WRITE_PORT_{HI,LO} registers, there is however some delay in the hardware to
re-organize its descriptors and it is possible that concurrent TX queues
eventually break this internal allocation scheme to the point where the
length/status part of the descriptor gets used for an incorrect data buffer.

The fix is to impose a global serialization for all TX queues in the short
section where we are writing to the WRITE_PORT_{HI,LO} registers which solves
the corruption even with multiple concurrent TX queues being used.

Fixes: 80105befdb4b ("net: systemport: add Broadcom SYSTEMPORT Ethernet MAC driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20211215202450.4086240-1-f.fainelli@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net/smc: Prevent smc_release() from long blocking

[ Upstream commit 5c15b3123f65f8fbb1b445d9a7e8812e0e435df2 ]

In nginx/wrk benchmark, there's a hung problem with high probability
on case likes that: (client will last several minutes to exit)

server: smc_run nginx

client: smc_run wrk -c 10000 -t 1 http://server

Client hangs with the following backtrace:

0 [ffffa7ce8Of3bbf8] __schedule at ffffffff9f9eOd5f
1 [ffffa7ce8Of3bc88] schedule at ffffffff9f9eløe6
2 [ffffa7ce8Of3bcaO] schedule_timeout at ffffffff9f9e3f3c
3 [ffffa7ce8Of3bd2O] wait_for_common at ffffffff9f9el9de
4 [ffffa7ce8Of3bd8O] __flush_work at ffffffff9fOfeOl3
5 [ffffa7ce8øf3bdfO] smc_release at ffffffffcO697d24 [smc]
6 [ffffa7ce8Of3be2O] __sock_release at ffffffff9f8O2e2d
7 [ffffa7ce8Of3be4ø] sock_close at ffffffff9f8ø2ebl
8 [ffffa7ce8øf3be48] __fput at ffffffff9f334f93
9 [ffffa7ce8Of3be78] task_work_run at ffffffff9flOlff5
10 [ffffa7ce8Of3beaO] do_exit at ffffffff9fOe5Ol2
11 [ffffa7ce8Of3bflO] do_group_exit at ffffffff9fOe592a
12 [ffffa7ce8Of3bf38] __x64_sys_exit_group at ffffffff9fOe5994
13 [ffffa7ce8Of3bf4O] do_syscall_64 at ffffffff9f9d4373
14 [ffffa7ce8Of3bfsO] entry_SYSCALL_64_after_hwframe at ffffffff9fa0007c

This issue dues to flush_work(), which is used to wait for
smc_connect_work() to finish in smc_release(). Once lots of
smc_connect_work() was pending or all executing work dangling,
smc_release() has to block until one worker comes to free, which
is equivalent to wait another smc_connnect_work() to finish.

In order to fix this, There are two changes:

1. For those idle smc_connect_work(), cancel it from the workqueue; for
   executing smc_connect_work(), waiting for it to finish. For that
   purpose, replace flush_work() with cancel_work_sync().

2. Since smc_connect() hold a reference for passive closing, if
   smc_connect_work() has been cancelled, release the reference.

Fixes: 24ac3a08e658 ("net/smc: rebuild nonblocking connect")
Reported-by: Tony Lu <tonylu@linux.alibaba.com>
Tested-by: Dust Li <dust.li@linux.alibaba.com>
Reviewed-by: Dust Li <dust.li@linux.alibaba.com>
Reviewed-by: Tony Lu <tonylu@linux.alibaba.com>
Signed-off-by: D. Wythe <alibuda@linux.alibaba.com>
Acked-by: Karsten Graul <kgraul@linux.ibm.com>
Link: https://lore.kernel.org/r/1639571361-101128-1-git-send-email-alibuda@linux.alibaba.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: Fix double 0x prefix print in SKB dump

[ Upstream commit 8a03ef676ade55182f9b05115763aeda6dc08159 ]

When printing netdev features %pNF already takes care of the 0x prefix,
remove the explicit one.

Fixes: 6413139dfc64 ("skbuff: increase verbosity when dumping skb data")
Signed-off-by: Gal Pressman <gal@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

sfc_ef100: potential dereference of null pointer

[ Upstream commit 407ecd1bd726f240123f704620d46e285ff30dd9 ]

The return value of kmalloc() needs to be checked.
To avoid use in efx_nic_update_stats() in case of the failure of alloc.

Fixes: b593b6f1b492 ("sfc_ef100: statistics gathering")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net/packet: rx_owner_map depends on pg_vec

[ Upstream commit ec6af094ea28f0f2dda1a6a33b14cd57e36a9755 ]

Packet sockets may switch ring versions. Avoid misinterpreting state
between versions, whose fields share a union. rx_owner_map is only
allocated with a packet ring (pg_vec) and both are swapped together.
If pg_vec is NULL, meaning no packet ring was allocated, then neither
was rx_owner_map. And the field may be old state from a tpacket_v3.

Fixes: 61fad6816fc1 ("net/packet: tpacket_rcv: avoid a producer race condition")
Reported-by: Syzbot <syzbot+1ac0994a0a0c55151121@syzkaller.appspotmail.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20211215143937.106178-1-willemdebruijn.kernel@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

netdevsim: Zero-initialize memory for new map's value in function nsim_bpf_map_alloc

[ Upstream commit 481221775d53d6215a6e5e9ce1cce6d2b4ab9a46 ]

Zero-initialize memory for new map's value in function nsim_bpf_map_alloc
since it may cause a potential kernel information leak issue, as follows:
1. nsim_bpf_map_alloc calls nsim_map_alloc_elem to allocate elements for
a new map.
2. nsim_map_alloc_elem uses kmalloc to allocate map's value, but doesn't
zero it.
3. A user application can use IOCTL BPF_MAP_LOOKUP_ELEM to get specific
element's information in the map.
4. The kernel function map_lookup_elem will call bpf_map_copy_value to get
the information allocated at step-2, then use copy_to_user to copy to the
user buffer.
This can only leak information for an array map.

Fixes: 395cacb5f1a0 ("netdevsim: bpf: support fake map offload")
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Haimin Zhang <tcs.kernel@gmail.com>
Link: https://lore.kernel.org/r/20211215111530.72103-1-tcs.kernel@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ixgbe: set X550 MDIO speed before talking to PHY

[ Upstream commit bf0a375055bd1afbbf02a0ef45f7655da7b71317 ]

The MDIO bus speed must be initialized before talking to the PHY the first
time in order to avoid talking to it using a speed that the PHY doesn't
support.

This fixes HW initialization error -17 (IXGBE_ERR_PHY_ADDR_INVALID) on
Denverton CPUs (a.k.a. the Atom C3000 family) on ports with a 10Gb network
plugged in. On those devices, HLREG0[MDCSPD] resets to 1, which combined
with the 10Gb network results in a 24MHz MDIO speed, which is apparently
too fast for the connected PHY. PHY register reads over MDIO bus return
garbage, leading to initialization failure.

Reproduced with Linux kernel 4.19 and 5.15-rc7. Can be reproduced using
the following setup:

* Use an Atom C3000 family system with at least one X552 LAN on the SoC
* Disable PXE or other BIOS network initialization if possible
  (the interface must not be initialized before Linux boots)
* Connect a live 10Gb Ethernet cable to an X550 port
* Power cycle (not reset, doesn't always work) the system and boot Linux
* Observe: ixgbe interfaces w/ 10GbE cables plugged in fail with error -17

Fixes: e84db7272798 ("ixgbe: Introduce function to control MDIO speed")
Signed-off-by: Cyril Novikov <cnovikov@lynx.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ixgbe: Document how to enable NBASE-T support

[ Upstream commit 271225fd57c2f1e0b3f8826df51be6c634affefe ]

Commit a296d665eae1 ("ixgbe: Add ethtool support to enable 2.5 and 5.0
Gbps support") introduced suppression of the advertisement of NBASE-T
speeds by default, according to Todd Fujinaka to accommodate customers
with network switches which could not cope with advertised NBASE-T
speeds, as posted in the E1000-devel mailing list:

https://sourceforge.net/p/e1000/mailman/message/37106269/

However, the suppression was not documented at all, nor was how to
enable NBASE-T support.

Properly document the NBASE-T suppression and how to enable NBASE-T
support.

Fixes: a296d665eae1 ("ixgbe: Add ethtool support to enable 2.5 and 5.0 Gbps support")
Reported-by: Robert Schlabbach <robert_s@gmx.net>
Signed-off-by: Robert Schlabbach <robert_s@gmx.net>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

igc: Fix typo in i225 LTR functions

[ Upstream commit 0182d1f3fa640888a2ed7e3f6df2fdb10adee7c8 ]

The LTR maximum value was incorrectly written using the scale from
the LTR minimum value. This would cause incorrect values to be sent,
in cases where the initial calculation lead to different min/max scales.

Fixes: 707abf069548 ("igc: Add initial LTR support")
Suggested-by: Dima Ruinskiy <dima.ruinskiy@intel.com>
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Nechama Kraus <nechamax.kraus@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

igbvf: fix double free in `igbvf_probe`

[ Upstream commit b6d335a60dc624c0d279333b22c737faa765b028 ]

In `igbvf_probe`, if register_netdev() fails, the program will go to
label err_hw_init, and then to label err_ioremap. In free_netdev() which
is just below label err_ioremap, there is `list_for_each_entry_safe` and
`netif_napi_del` which aims to delete all entries in `dev->napi_list`.
The program has added an entry `adapter->rx_ring->napi` which is added by
`netif_napi_add` in igbvf_alloc_queues(). However, adapter->rx_ring has
been freed below label err_hw_init. So this a UAF.

In terms of how to patch the problem, we can refer to igbvf_remove() and
delete the entry before `adapter->rx_ring`.

The KASAN logs are as follows:

[   35.126075] BUG: KASAN: use-after-free in free_netdev+0x1fd/0x450
[   35.127170] Read of size 8 at addr ffff88810126d990 by task modprobe/366
[   35.128360]
[   35.128643] CPU: 1 PID: 366 Comm: modprobe Not tainted 5.15.0-rc2+ #14
[   35.129789] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.12.0-59-gc9ba5276e321-prebuilt.qemu.org 04/01/2014
[   35.131749] Call Trace:
[   35.132199]  dump_stack_lvl+0x59/0x7b
[   35.132865]  print_address_description+0x7c/0x3b0
[   35.133707]  ? free_netdev+0x1fd/0x450
[   35.134378]  __kasan_report+0x160/0x1c0
[   35.135063]  ? free_netdev+0x1fd/0x450
[   35.135738]  kasan_report+0x4b/0x70
[   35.136367]  free_netdev+0x1fd/0x450
[   35.137006]  igbvf_probe+0x121d/0x1a10 [igbvf]
[   35.137808]  ? igbvf_vlan_rx_add_vid+0x100/0x100 [igbvf]
[   35.138751]  local_pci_probe+0x13c/0x1f0
[   35.139461]  pci_device_probe+0x37e/0x6c0
[   35.165526]
[   35.165806] Allocated by task 366:
[   35.166414]  ____kasan_kmalloc+0xc4/0xf0
[   35.167117]  foo_kmem_cache_alloc_trace+0x3c/0x50 [igbvf]
[   35.168078]  igbvf_probe+0x9c5/0x1a10 [igbvf]
[   35.168866]  local_pci_probe+0x13c/0x1f0
[   35.169565]  pci_device_probe+0x37e/0x6c0
[   35.179713]
[   35.179993] Freed by task 366:
[   35.180539]  kasan_set_track+0x4c/0x80
[   35.181211]  kasan_set_free_info+0x1f/0x40
[   35.181942]  ____kasan_slab_free+0x103/0x140
[   35.182703]  kfree+0xe3/0x250
[   35.183239]  igbvf_probe+0x1173/0x1a10 [igbvf]
[   35.184040]  local_pci_probe+0x13c/0x1f0

Fixes: d4e0fe01a38a0 (igbvf: add new driver to support 82576 virtual functions)
Reported-by: Zheyu Ma <zheyuma97@gmail.com>
Signed-off-by: Letu Ren <fantasquex@gmail.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

igb: Fix removal of unicast MAC filters of VFs

[ Upstream commit 584af82154f56e6b2740160fcc84a2966d969e15 ]

Move checking condition of VF MAC filter before clearing
or adding MAC filter to VF to prevent potential blackout caused
by removal of necessary and working VF's MAC filter.

Fixes: 1b8b062a99dc ("igb: add VF trust infrastructure")
Signed-off-by: Karen Sornek <karen.sornek@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

soc/tegra: fuse: Fix bitwise vs. logical OR warning

[ Upstream commit a7083763619f7485ccdade160deb81737cf2732f ]

A new warning in clang points out two instances where boolean
expressions are being used with a bitwise OR instead of logical OR:

drivers/soc/tegra/fuse/speedo-tegra20.c:72:9: warning: use of bitwise '|' with boolean operands [-Wbitwise-instead-of-logical]
                reg = tegra_fuse_read_spare(i) |
                      ^~~~~~~~~~~~~~~~~~~~~~~~~~
                                               ||
drivers/soc/tegra/fuse/speedo-tegra20.c:72:9: note: cast one or both operands to int to silence this warning
drivers/soc/tegra/fuse/speedo-tegra20.c:87:9: warning: use of bitwise '|' with boolean operands [-Wbitwise-instead-of-logical]
                reg = tegra_fuse_read_spare(i) |
                      ^~~~~~~~~~~~~~~~~~~~~~~~~~
                                               ||
drivers/soc/tegra/fuse/speedo-tegra20.c:87:9: note: cast one or both operands to int to silence this warning
2 warnings generated.

The motivation for the warning is that logical operations short circuit
while bitwise operations do not.

In this instance, tegra_fuse_read_spare() is not semantically returning
a boolean, it is returning a bit value. Use u32 for its return type so
that it can be used with either bitwise or boolean operators without any
warnings.

Fixes: 25cd5a391478 ("ARM: tegra: Add speedo-based process identification")
Link: https://github.com/ClangBuiltLinux/linux/issues/1488
Suggested-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

mptcp: clear 'kern' flag from fallback sockets

[ Upstream commit d6692b3b97bdc165d150f4c1505751a323a80717 ]

The mptcp ULP extension relies on sk->sk_sock_kern being set correctly:
It prevents setsockopt(fd, IPPROTO_TCP, TCP_ULP, "mptcp", 6); from
working for plain tcp sockets (any userspace-exposed socket).

But in case of fallback, accept() can return a plain tcp sk.
In such case, sk is still tagged as 'kernel' and setsockopt will work.

This will crash the kernel, The subflow extension has a NULL ctx->conn
mptcp socket:

BUG: KASAN: null-ptr-deref in subflow_data_ready+0x181/0x2b0
Call Trace:
 tcp_data_ready+0xf8/0x370
 [..]

Fixes: cf7da0d66cc1 ("mptcp: Create SUBFLOW socket for incoming connections")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/amd/pm: fix a potential gpu_metrics_table memory leak

[ Upstream commit aa464957f7e660abd554f2546a588f6533720e21 ]

Memory is allocated for gpu_metrics_table in renoir_init_smc_tables(),
but not freed in int smu_v12_0_fini_smc_tables(). Free it!

Fixes: 95868b85764a ("drm/amd/powerplay: add Renoir support for gpu metrics export")

Signed-off-by: Lang Yu <lang.yu@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

rds: memory leak in __rds_conn_create()

[ Upstream commit 5f9562ebe710c307adc5f666bf1a2162ee7977c0 ]

__rds_conn_create() did not release conn->c_path when loop_trans != 0 and
trans->t_prefer_loopback != 0 and is_outgoing == 0.

Fixes: aced3ce57cd3 ("RDS tcp loopback connection can hang")
Signed-off-by: Hangyu Hua <hbh25y@gmail.com>
Reviewed-by: Sharath Srinivasan <sharath.srinivasan@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

flow_offload: return EOPNOTSUPP for the unsupported mpls action type

[ Upstream commit 166b6a46b78bf8b9559a6620c3032f9fe492e082 ]

We need to return EOPNOTSUPP for the unsupported mpls action type when
setup the flow action.

In the original implement, we will return 0 for the unsupported mpls
action type, actually we do not setup it and the following actions
to the flow action entry.

Fixes: 9838b20a7fb2 ("net: sched: take rtnl lock in tc_setup_flow_action()")
Signed-off-by: Baowen Zheng <baowen.zheng@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

mac80211: fix lookup when adding AddBA extension element

[ Upstream commit 511ab0c1dfb260a6b17b8771109e8d63474473a7 ]

We should be doing the HE capabilities lookup based on the full
interface type so if P2P doesn't have HE but client has it doesn't
get confused. Fix that.

Fixes: 2ab45876756f ("mac80211: add support for the ADDBA extension element")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20211129152938.010fc1d61137.If3a468145f29d670cb00a693bed559d8290ba693@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

mac80211: agg-tx: don't schedule_and_wake_txq() under sta->lock

[ Upstream commit 06c41bda0ea14aa7fba932a9613c4ee239682cf0 ]

When we call ieee80211_agg_start_txq(), that will in turn call
schedule_and_wake_txq(). Called from ieee80211_stop_tx_ba_cb()
this is done under sta->lock, which leads to certain circular
lock dependencies, as reported by Chris Murphy:
https://lore.kernel.org/r/CAJCQCtSXJ5qA4bqSPY=oLRMbv-irihVvP7A2uGutEbXQVkoNaw@mail.gmail.com

In general, ieee80211_agg_start_txq() is usually not called
with sta->lock held, only in this one place. But it's always
called with sta->ampdu_mlme.mtx held, and that's therefore
clearly sufficient.

Change ieee80211_stop_tx_ba_cb() to also call it without the
sta->lock held, by factoring it out of ieee80211_remove_tid_tx()
(which is only called in this one place).

This breaks the locking chain and makes it less likely that
we'll have similar locking chain problems in the future.

Fixes: ba8c3d6f16a1 ("mac80211: add an intermediate software queue implementation")
Reported-by: Chris Murphy <lists@colorremedies.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20211202152554.f519884c8784.I555fef8e67d93fff3d9a304886c4a9f8b322e591@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/ast: potential dereference of null pointer

[ Upstream commit fea3fdf975dd9f3e5248afaab8fe023db313f005 ]

The return value of kzalloc() needs to be checked.
To avoid use of null pointer '&ast_state->base' in case of the
failure of alloc.

Fixes: f0adbc382b8b ("drm/ast: Allocate initial CRTC state of the correct size")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20211214014126.2211535-1-jiasheng@iscas.ac.cn
Signed-off-by: Sasha Levin <sashal@kernel.org>

selftest/net/forwarding: declare NETIFS p9 p10

[ Upstream commit 71da1aec215290e249d09c44c768df859f3a3bba ]

The recent GRE selftests defined NUM_NETIFS=10. If the users copy
forwarding.config.sample to forwarding.config directly, they will get
error "Command line is not complete" when run the GRE tests, because
create_netif_veth() failed with no interface name defined.

Fix it by extending the NETIFS with p9 and p10.

Fixes: 2800f2485417 ("selftests: forwarding: Test multipath hashing on inner IP pkts for GRE tunnel")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net/sched: sch_ets: don't remove idle classes from the round-robin list

[ Upstream commit c062f2a0b04d86c5b8c9d973bea43493eaca3d32 ]

Shuang reported that the following script:

 1) tc qdisc add dev ddd0 handle 10: parent 1: ets bands 8 strict 4 priomap 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7
 2) mausezahn ddd0  -A 10.10.10.1 -B 10.10.10.2 -c 0 -a own -b 00:c1:a0:c1:a0:00 -t udp &
 3) tc qdisc change dev ddd0 handle 10: ets bands 4 strict 2 quanta 2500 2500 priomap 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3

crashes systematically when line 2) is commented:

 list_del corruption, ffff8e028404bd30->next is LIST_POISON1 (dead000000000100)
 ------------[ cut here ]------------
 kernel BUG at lib/list_debug.c:47!
 invalid opcode: 0000 [#1] PREEMPT SMP NOPTI
 CPU: 0 PID: 954 Comm: tc Not tainted 5.16.0-rc4+ #478
 Hardware name: Red Hat KVM, BIOS 1.11.1-4.module+el8.1.0+4066+0f1aadab 04/01/2014
 RIP: 0010:__list_del_entry_valid.cold.1+0x12/0x47
 Code: fe ff 0f 0b 48 89 c1 4c 89 c6 48 c7 c7 08 42 1b 87 e8 1d c5 fe ff 0f 0b 48 89 fe 48 89 c2 48 c7 c7 98 42 1b 87 e8 09 c5 fe ff <0f> 0b 48 c7 c7 48 43 1b 87 e8 fb c4 fe ff 0f 0b 48 89 f2 48 89 fe
 RSP: 0018:ffffae46807a3888 EFLAGS: 00010246
 RAX: 000000000000004e RBX: 0000000000000007 RCX: 0000000000000202
 RDX: 0000000000000000 RSI: ffffffff871ac536 RDI: 00000000ffffffff
 RBP: ffffae46807a3a10 R08: 0000000000000000 R09: c0000000ffff7fff
 R10: 0000000000000001 R11: ffffae46807a36a8 R12: ffff8e028404b800
 R13: ffff8e028404bd30 R14: dead000000000100 R15: ffff8e02fafa2400
 FS:  00007efdc92e4480(0000) GS:ffff8e02fb600000(0000) knlGS:0000000000000000
 CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
 CR2: 0000000000682f48 CR3: 00000001058be000 CR4: 0000000000350ef0
 Call Trace:
  <TASK>
  ets_qdisc_change+0x58b/0xa70 [sch_ets]
  tc_modify_qdisc+0x323/0x880
  rtnetlink_rcv_msg+0x169/0x4a0
  netlink_rcv_skb+0x50/0x100
  netlink_unicast+0x1a5/0x280
  netlink_sendmsg+0x257/0x4d0
  sock_sendmsg+0x5b/0x60
  ____sys_sendmsg+0x1f2/0x260
  ___sys_sendmsg+0x7c/0xc0
  __sys_sendmsg+0x57/0xa0
  do_syscall_64+0x3a/0x80
  entry_SYSCALL_64_after_hwframe+0x44/0xae
 RIP: 0033:0x7efdc8031338
 Code: 89 02 48 c7 c0 ff ff ff ff eb b5 0f 1f 80 00 00 00 00 f3 0f 1e fa 48 8d 05 25 43 2c 00 8b 00 85 c0 75 17 b8 2e 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 58 c3 0f 1f 80 00 00 00 00 41 54 41 89 d4 55
 RSP: 002b:00007ffdf1ce9828 EFLAGS: 00000246 ORIG_RAX: 000000000000002e
 RAX: ffffffffffffffda RBX: 0000000061b37a97 RCX: 00007efdc8031338
 RDX: 0000000000000000 RSI: 00007ffdf1ce9890 RDI: 0000000000000003
 RBP: 0000000000000000 R08: 0000000000000001 R09: 000000000078a940
 R10: 000000000000000c R11: 0000000000000246 R12: 0000000000000001
 R13: 0000000000688880 R14: 0000000000000000 R15: 0000000000000000
  </TASK>
 Modules linked in: sch_ets sch_tbf dummy rfkill iTCO_wdt iTCO_vendor_support intel_rapl_msr intel_rapl_common joydev pcspkr i2c_i801 virtio_balloon i2c_smbus lpc_ich ip_tables xfs libcrc32c crct10dif_pclmul crc32_pclmul crc32c_intel serio_raw ghash_clmulni_intel ahci libahci libata virtio_blk virtio_console virtio_net net_failover failover sunrpc dm_mirror dm_region_hash dm_log dm_mod [last unloaded: sch_ets]
 ---[ end trace f35878d1912655c2 ]---
 RIP: 0010:__list_del_entry_valid.cold.1+0x12/0x47
 Code: fe ff 0f 0b 48 89 c1 4c 89 c6 48 c7 c7 08 42 1b 87 e8 1d c5 fe ff 0f 0b 48 89 fe 48 89 c2 48 c7 c7 98 42 1b 87 e8 09 c5 fe ff <0f> 0b 48 c7 c7 48 43 1b 87 e8 fb c4 fe ff 0f 0b 48 89 f2 48 89 fe
 RSP: 0018:ffffae46807a3888 EFLAGS: 00010246
 RAX: 000000000000004e RBX: 0000000000000007 RCX: 0000000000000202
 RDX: 0000000000000000 RSI: ffffffff871ac536 RDI: 00000000ffffffff
 RBP: ffffae46807a3a10 R08: 0000000000000000 R09: c0000000ffff7fff
 R10: 0000000000000001 R11: ffffae46807a36a8 R12: ffff8e028404b800
 R13: ffff8e028404bd30 R14: dead000000000100 R15: ffff8e02fafa2400
 FS:  00007efdc92e4480(0000) GS:ffff8e02fb600000(0000) knlGS:0000000000000000
 CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
 CR2: 0000000000682f48 CR3: 00000001058be000 CR4: 0000000000350ef0
 Kernel panic - not syncing: Fatal exception in interrupt
 Kernel Offset: 0x4e00000 from 0xffffffff81000000 (relocation range: 0xffffffff80000000-0xffffffffbfffffff)
 ---[ end Kernel panic - not syncing: Fatal exception in interrupt ]---

we can remove 'q->classes[i].alist' only if DRR class 'i' was part of the
active list. In the ETS scheduler DRR classes belong to that list only if
the queue length is greater than zero: we need to test for non-zero value
of 'q->classes[i].qdisc->q.qlen' before removing from the list, similarly
to what has been done elsewhere in the ETS code.

Fixes: de6d25924c2a ("net/sched: sch_ets: don't peek at classes beyond 'nbands'")
Reported-by: Shuang Li <shuali@redhat.com>
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

dmaengine: st_fdma: fix MODULE_ALIAS

[ Upstream commit 822c9f2b833c53fc67e8adf6f63ecc3ea24d502c ]

modprobe can't handle spaces in aliases.

Fixes: 6b4cd727eaf1 ("dmaengine: st_fdma: Add STMicroelectronics FDMA engine driver support")
Signed-off-by: Alyssa Ross <hi@alyssa.is>
Link: https://lore.kernel.org/r/20211125154441.2626214-1-hi@alyssa.is
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

selftests: Fix IPv6 address bind tests

[ Upstream commit 28a2686c185e84b6aa6a4d9c9a972360eb7ca266 ]

IPv6 allows binding a socket to a device then binding to an address
not on the device (__inet6_bind -> ipv6_chk_addr with strict flag
not set). Update the bind tests to reflect legacy behavior.

Fixes: 34d0302ab861 ("selftests: Add ipv6 address bind tests to fcnal-test")
Reported-by: Li Zhijian <lizhijian@fujitsu.com>
Signed-off-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

selftests: Fix raw socket bind tests with VRF

[ Upstream commit 0f108ae4452025fef529671998f6c7f1c4526790 ]

Commit referenced below added negative socket bind tests for VRF. The
socket binds should fail since the address to bind to is in a VRF yet
the socket is not bound to the VRF or a device within it. Update the
expected return code to check for 1 (bind failure) so the test passes
when the bind fails as expected. Add a 'show_hint' comment to explain
why the bind is expected to fail.

Fixes: 75b2b2b3db4c ("selftests: Add ipv4 address bind tests to fcnal-test")
Reported-by: Li Zhijian <lizhijian@fujitsu.com>
Signed-off-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

selftests: Add duplicate config only for MD5 VRF tests

[ Upstream commit 7e0147592b5c4f9e2eb8c54a7857a56d4863f74e ]

Commit referenced below added configuration in the default VRF that
duplicates a VRF to check MD5 passwords are properly used and fail
when expected. That config should not be added all the time as it
can cause tests to pass that should not (by matching on default VRF
setup when it should not). Move the duplicate setup to a function
that is only called for the MD5 tests and add a cleanup function
to remove it after the MD5 tests.

Fixes: 5cad8bce26e0 ("fcnal-test: Add TCP MD5 tests for VRF")
Signed-off-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: hns3: fix use-after-free bug in hclgevf_send_mbx_msg

[ Upstream commit 27cbf64a766e86f068ce6214f04c00ceb4db1af4 ]

Currently, the hns3_remove function firstly uninstall client instance,
and then uninstall acceletion engine device. The netdevice is freed in
client instance uninstall process, but acceletion engine device uninstall
process still use it to trace runtime information. This causes a use after
free problem.

So fixes it by check the instance register state to avoid use after free.

Fixes: d8355240cf8f ("net: hns3: add trace event support for PF/VF mailbox")
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

inet_diag: fix kernel-infoleak for UDP sockets

[ Upstream commit 71ddeac8cd1d217744a0e060ff520e147c9328d1 ]

KMSAN reported a kernel-infoleak [1], that can exploited
by unpriv users.

After analysis it turned out UDP was not initializing
r->idiag_expires. Other users of inet_sk_diag_fill()
might make the same mistake in the future, so fix this
in inet_sk_diag_fill().

[1]
BUG: KMSAN: kernel-infoleak in instrument_copy_to_user include/linux/instrumented.h:121 [inline]
BUG: KMSAN: kernel-infoleak in copyout lib/iov_iter.c:156 [inline]
BUG: KMSAN: kernel-infoleak in _copy_to_iter+0x69d/0x25c0 lib/iov_iter.c:670
 instrument_copy_to_user include/linux/instrumented.h:121 [inline]
 copyout lib/iov_iter.c:156 [inline]
 _copy_to_iter+0x69d/0x25c0 lib/iov_iter.c:670
 copy_to_iter include/linux/uio.h:155 [inline]
 simple_copy_to_iter+0xf3/0x140 net/core/datagram.c:519
 __skb_datagram_iter+0x2cb/0x1280 net/core/datagram.c:425
 skb_copy_datagram_iter+0xdc/0x270 net/core/datagram.c:533
 skb_copy_datagram_msg include/linux/skbuff.h:3657 [inline]
 netlink_recvmsg+0x660/0x1c60 net/netlink/af_netlink.c:1974
 sock_recvmsg_nosec net/socket.c:944 [inline]
 sock_recvmsg net/socket.c:962 [inline]
 sock_read_iter+0x5a9/0x630 net/socket.c:1035
 call_read_iter include/linux/fs.h:2156 [inline]
 new_sync_read fs/read_write.c:400 [inline]
 vfs_read+0x1631/0x1980 fs/read_write.c:481
 ksys_read+0x28c/0x520 fs/read_write.c:619
 __do_sys_read fs/read_write.c:629 [inline]
 __se_sys_read fs/read_write.c:627 [inline]
 __x64_sys_read+0xdb/0x120 fs/read_write.c:627
 do_syscall_x64 arch/x86/entry/common.c:51 [inline]
 do_syscall_64+0x54/0xd0 arch/x86/entry/common.c:82
 entry_SYSCALL_64_after_hwframe+0x44/0xae

Uninit was created at:
 slab_post_alloc_hook mm/slab.h:524 [inline]
 slab_alloc_node mm/slub.c:3251 [inline]
 __kmalloc_node_track_caller+0xe0c/0x1510 mm/slub.c:4974
 kmalloc_reserve net/core/skbuff.c:354 [inline]
 __alloc_skb+0x545/0xf90 net/core/skbuff.c:426
 alloc_skb include/linux/skbuff.h:1126 [inline]
 netlink_dump+0x3d5/0x16a0 net/netlink/af_netlink.c:2245
 __netlink_dump_start+0xd1c/0xee0 net/netlink/af_netlink.c:2370
 netlink_dump_start include/linux/netlink.h:254 [inline]
 inet_diag_handler_cmd+0x2e7/0x400 net/ipv4/inet_diag.c:1343
 sock_diag_rcv_msg+0x24a/0x620
 netlink_rcv_skb+0x447/0x800 net/netlink/af_netlink.c:2491
 sock_diag_rcv+0x63/0x80 net/core/sock_diag.c:276
 netlink_unicast_kernel net/netlink/af_netlink.c:1319 [inline]
 netlink_unicast+0x1095/0x1360 net/netlink/af_netlink.c:1345
 netlink_sendmsg+0x16f3/0x1870 net/netlink/af_netlink.c:1916
 sock_sendmsg_nosec net/socket.c:704 [inline]
 sock_sendmsg net/socket.c:724 [inline]
 sock_write_iter+0x594/0x690 net/socket.c:1057
 do_iter_readv_writev+0xa7f/0xc70
 do_iter_write+0x52c/0x1500 fs/read_write.c:851
 vfs_writev fs/read_write.c:924 [inline]
 do_writev+0x63f/0xe30 fs/read_write.c:967
 __do_sys_writev fs/read_write.c:1040 [inline]
 __se_sys_writev fs/read_write.c:1037 [inline]
 __x64_sys_writev+0xe5/0x120 fs/read_write.c:1037
 do_syscall_x64 arch/x86/entry/common.c:51 [inline]
 do_syscall_64+0x54/0xd0 arch/x86/entry/common.c:82
 entry_SYSCALL_64_after_hwframe+0x44/0xae

Bytes 68-71 of 312 are uninitialized
Memory access of size 312 starts at ffff88812ab54000
Data copied to user address 0000000020001440

CPU: 1 PID: 6365 Comm: syz-executor801 Not tainted 5.16.0-rc3-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011

Fixes: 3c4d05c80567 ("inet_diag: Introduce the inet socket dumping routine")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Link: https://lore.kernel.org/r/20211209185058.53917-1-eric.dumazet@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

sch_cake: do not call cake_destroy() from cake_init()

[ Upstream commit ab443c53916730862cec202078d36fd4008bea79 ]

qdiscs are not supposed to call their own destroy() method
from init(), because core stack already does that.

syzbot was able to trigger use after free:

DEBUG_LOCKS_WARN_ON(lock->magic != lock)
WARNING: CPU: 0 PID: 21902 at kernel/locking/mutex.c:586 __mutex_lock_common kernel/locking/mutex.c:586 [inline]
WARNING: CPU: 0 PID: 21902 at kernel/locking/mutex.c:586 __mutex_lock+0x9ec/0x12f0 kernel/locking/mutex.c:740
Modules linked in:
CPU: 0 PID: 21902 Comm: syz-executor189 Not tainted 5.16.0-rc4-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
RIP: 0010:__mutex_lock_common kernel/locking/mutex.c:586 [inline]
RIP: 0010:__mutex_lock+0x9ec/0x12f0 kernel/locking/mutex.c:740
Code: 08 84 d2 0f 85 19 08 00 00 8b 05 97 38 4b 04 85 c0 0f 85 27 f7 ff ff 48 c7 c6 20 00 ac 89 48 c7 c7 a0 fe ab 89 e8 bf 76 ba ff <0f> 0b e9 0d f7 ff ff 48 8b 44 24 40 48 8d b8 c8 08 00 00 48 89 f8
RSP: 0018:ffffc9000627f290 EFLAGS: 00010282
RAX: 0000000000000000 RBX: 0000000000000000 RCX: 0000000000000000
RDX: ffff88802315d700 RSI: ffffffff815f1db8 RDI: fffff52000c4fe44
RBP: ffff88818f28e000 R08: 0000000000000000 R09: 0000000000000000
R10: ffffffff815ebb5e R11: 0000000000000000 R12: 0000000000000000
R13: dffffc0000000000 R14: ffffc9000627f458 R15: 0000000093c30000
FS:  0000555556abc400(0000) GS:ffff8880b9c00000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007fda689c3303 CR3: 000000001cfbb000 CR4: 0000000000350ef0
Call Trace:
 <TASK>
 tcf_chain0_head_change_cb_del+0x2e/0x3d0 net/sched/cls_api.c:810
 tcf_block_put_ext net/sched/cls_api.c:1381 [inline]
 tcf_block_put_ext net/sched/cls_api.c:1376 [inline]
 tcf_block_put+0xbc/0x130 net/sched/cls_api.c:1394
 cake_destroy+0x3f/0x80 net/sched/sch_cake.c:2695
 qdisc_create.constprop.0+0x9da/0x10f0 net/sched/sch_api.c:1293
 tc_modify_qdisc+0x4c5/0x1980 net/sched/sch_api.c:1660
 rtnetlink_rcv_msg+0x413/0xb80 net/core/rtnetlink.c:5571
 netlink_rcv_skb+0x153/0x420 net/netlink/af_netlink.c:2496
 netlink_unicast_kernel net/netlink/af_netlink.c:1319 [inline]
 netlink_unicast+0x533/0x7d0 net/netlink/af_netlink.c:1345
 netlink_sendmsg+0x904/0xdf0 net/netlink/af_netlink.c:1921
 sock_sendmsg_nosec net/socket.c:704 [inline]
 sock_sendmsg+0xcf/0x120 net/socket.c:724
 ____sys_sendmsg+0x6e8/0x810 net/socket.c:2409
 ___sys_sendmsg+0xf3/0x170 net/socket.c:2463
 __sys_sendmsg+0xe5/0x1b0 net/socket.c:2492
 do_syscall_x64 arch/x86/entry/common.c:50 [inline]
 do_syscall_64+0x35/0xb0 arch/x86/entry/common.c:80
 entry_SYSCALL_64_after_hwframe+0x44/0xae
RIP: 0033:0x7f1bb06badb9
Code: Unable to access opcode bytes at RIP 0x7f1bb06bad8f.
RSP: 002b:00007fff3012a658 EFLAGS: 00000246 ORIG_RAX: 000000000000002e
RAX: ffffffffffffffda RBX: 0000000000000003 RCX: 00007f1bb06badb9
RDX: 0000000000000000 RSI: 00000000200007c0 RDI: 0000000000000003
RBP: 0000000000000000 R08: 0000000000000003 R09: 0000000000000003
R10: 0000000000000003 R11: 0000000000000246 R12: 00007fff3012a688
R13: 00007fff3012a6a0 R14: 00007fff3012a6e0 R15: 00000000000013c2
 </TASK>

Fixes: 046f6fd5daef ("sched: Add Common Applications Kept Enhanced (cake) qdisc")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Link: https://lore.kernel.org/r/20211210142046.698336-1-eric.dumazet@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>