review.tizen.org Git - platform/kernel/linux-starfive.git/log

cxl: Rename member @dport of struct cxl_dport to @dport_dev

Reading code like dport->dport does not immediately suggest that this
points to the corresponding device structure of the dport. Rename
struct member @dport to @dport_dev.

While at it, also rename @new argument of add_dport() to @dport. This
better describes the variable as a dport (e.g. new->dport becomes to
dport->dport_dev).

Co-developed-by: Terry Bowman <terry.bowman@amd.com>
Signed-off-by: Terry Bowman <terry.bowman@amd.com>
Signed-off-by: Robert Richter <rrichter@amd.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/20230622205523.85375-5-terry.bowman@amd.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>

cxl/rch: Prepare for caching the MMIO mapped PCIe AER capability

Prepare cxl_probe_rcrb() for retrieving more than just the component
register block. The RCH AER handling code wants to get back to the AER
capability that happens to be MMIO mapped rather then configuration
cycles.

Move RCRB specific downstream port data, like the RCRB base and the
AER capability offset, into its own data structure ('struct
cxl_rcrb_info') for cxl_probe_rcrb() to fill. Extend 'struct
cxl_dport' to include a 'struct cxl_rcrb_info' attribute.

This centralizes all RCRB scanning in one routine.

Co-developed-by: Robert Richter <rrichter@amd.com>
Signed-off-by: Robert Richter <rrichter@amd.com>
Signed-off-by: Terry Bowman <terry.bowman@amd.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/20230622205523.85375-4-terry.bowman@amd.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>

cxl/acpi: Probe RCRB later during RCH downstream port creation

The RCRB is extracted already during ACPI CEDT table parsing while the
data of this is needed not earlier than dport creation. This
implementation comes with drawbacks: During ACPI table scan there is
already MMIO access including mapping and unmapping, but only ACPI
data should be collected here. The collected data must be transferred
through a couple of interfaces until it is finally consumed when
creating the dport. This causes complex data structures and function
interfaces. Additionally, RCRB parsing will be extended to also
extract AER data, it would be much easier do this at a later point
during port and dport creation when the data structures are available
to hold that data.

To simplify all that, probe the RCRB at a later point during RCH
downstream port creation. Change ACPI table parser to only extract the
base address of either the component registers or the RCRB. Parse and
extract the RCRB in devm_cxl_add_rch_dport().

This is in preparation to centralize all RCRB scanning.

Signed-off-by: Robert Richter <rrichter@amd.com>
Signed-off-by: Terry Bowman <terry.bowman@amd.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/20230622205523.85375-2-terry.bowman@amd.com
Co-developed-by: Dan Williams <dan.j.williams@intel.com>
Link: https://lore.kernel.org/r/20230622205523.85375-3-terry.bowman@amd.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>

Linux 6.4-rc6

Merge tag 'x86_urgent_for_v6.4_rc6' of git://git./linux/kernel/git/tip/tip

Pull x86 fix from Borislav Petkov:

- Set up the kernel CS earlier in the boot process in case EFI boots
   the kernel after bypassing the decompressor and the CS descriptor
   used ends up being the EFI one which is not mapped in the identity
   page table, leading to early SEV/SNP guest communication exceptions
   resulting in the guest crashing

* tag 'x86_urgent_for_v6.4_rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/head/64: Switch to KERNEL_CS as soon as new GDT is installed

Merge tag '6.4-rc5-smb3-server-fixes' of git://git.samba.org/ksmbd

Pull smb server fixes from Steve French:
"Five smb3 server fixes, all also for stable:

   - Fix four slab out of bounds warnings: improve checks for protocol
     id, and for small packet length, and for create context parsing,
     and for negotiate context parsing

   - Fix for incorrect dereferencing POSIX ACLs"

* tag '6.4-rc5-smb3-server-fixes' of git://git.samba.org/ksmbd:
  ksmbd: validate smb request protocol id
  ksmbd: check the validation of pdu_size in ksmbd_conn_handler_loop
  ksmbd: fix posix_acls and acls dereferencing possible ERR_PTR()
  ksmbd: fix out-of-bound read in parse_lease_state()
  ksmbd: fix out-of-bound read in deassemble_neg_contexts()

Merge tag 'i2c-for-6.4-rc6' of git://git./linux/kernel/git/wsa/linux

Pull i2c fixes from Wolfram Sang:
"Biggest news is that Andi Shyti steps in for maintaining the
  controller drivers. Thank you very much!

  Other than that, one new driver maintainer and the rest is usual
  driver bugfixes. at24 has a Kconfig dependecy fix"

* tag 'i2c-for-6.4-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  MAINTAINERS: Add entries for Renesas RZ/V2M I2C driver
  eeprom: at24: also select REGMAP
  i2c: sprd: Delete i2c adapter in .remove's error path
  i2c: mv64xxx: Fix reading invalid status value in atomic mode
  i2c: designware: fix idx_write_cnt in read loop
  i2c: mchp-pci1xxxx: Avoid cast to incompatible function type
  i2c: img-scb: Fix spelling mistake "innacurate" -> "inaccurate"
  MAINTAINERS: Add myself as I2C host drivers maintainer

Merge tag 'soundwire-6.4-fixes' of git://git./linux/kernel/git/vkoul/soundwire

Pull soundwire fixes from Vinod Koul:
"Core fix for missing flag clear, error patch handling in qcom driver
  and BIOS quirk for HP Spectre x360:

   - HP Spectre x360 soundwire DMI quirk

   - Error path handling for qcom driver

   - Core fix for missing clear of alloc_slave_rt"

* tag 'soundwire-6.4-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/soundwire:
  soundwire: stream: Add missing clear of alloc_slave_rt
  soundwire: qcom: add proper error paths in qcom_swrm_startup()
  soundwire: dmi-quirks: add new mapping for HP Spectre x360

Merge tag 'arm-fixes-6.4-2' of git://git./linux/kernel/git/soc/soc

Pull ARM SoC fixes from Arnd Bergmann:
"Most of the changes this time are for the Qualcomm Snapdragon
  platforms.

  There are bug fixes for error handling in Qualcomm icc-bwmon,
  rpmh-rsc, ramp_controller and rmtfs driver as well as the AMD tee
  firmware driver and a missing initialization in the Arm ff-a firmware
  driver. The Qualcomm RPMh and EDAC drivers need some rework to work
  correctly on all supported chips.

  The DT fixes include:

   - i.MX8 fixes for gpio, pinmux and clock settings

   - ADS touchscreen gpio polarity settings in several machines

   - Address dtb warnings for caches, panel and input-enable properties
     on Qualcomm platforms

   - Incorrect data on qualcomm platforms fir SA8155P power domains,
     SM8550 LLCC, SC7180-lite SDRAM frequencies and SM8550 soundwire

   - Remoteproc firmware paths are corrected for Sony Xperia 10 IV"

* tag 'arm-fixes-6.4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (36 commits)
  firmware: arm_ffa: Set handle field to zero in memory descriptor
  ARM: dts: Fix erroneous ADS touchscreen polarities
  arm64: dts: imx8mn-beacon: Fix SPI CS pinmux
  arm64: dts: imx8-ss-dma: assign default clock rate for lpuarts
  arm64: dts: imx8qm-mek: correct GPIOs for USDHC2 CD and WP signals
  EDAC/qcom: Get rid of hardcoded register offsets
  EDAC/qcom: Remove superfluous return variable assignment in qcom_llcc_core_setup()
  arm64: dts: qcom: sm8550: Use the correct LLCC register scheme
  dt-bindings: cache: qcom,llcc: Fix SM8550 description
  arm64: dts: qcom: sc7180-lite: Fix SDRAM freq for misidentified sc7180-lite boards
  arm64: dts: qcom: sm8550: use uint16 for Soundwire interval
  soc: qcom: rpmhpd: Add SA8155P power domains
  arm64: dts: qcom: Split out SA8155P and use correct RPMh power domains
  dt-bindings: power: qcom,rpmpd: Add SA8155P
  soc: qcom: Rename ice to qcom_ice to avoid module name conflict
  soc: qcom: rmtfs: Fix error code in probe()
  soc: qcom: ramp_controller: Fix an error handling path in qcom_ramp_controller_probe()
  ARM: dts: at91: sama7g5ek: fix debounce delay property for shdwc
  ARM: at91: pm: fix imbalanced reference counter for ethernet devices
  arm64: dts: qcom: sm6375-pdx225: Fix remoteproc firmware paths
  ...

Merge tag 'block-6.4-2023-06-09' of git://git.kernel.dk/linux

Pull block fixes from Jens Axboe:

- Fix an issue with the hardware queue nr_active, causing it to become
   imbalanced (Tian)

- Fix an issue with null_blk not releasing pages if configured as
   memory backed (Nitesh)

- Fix a locking issue in dasd (Jan)

* tag 'block-6.4-2023-06-09' of git://git.kernel.dk/linux:
  s390/dasd: Use correct lock while counting channel queue length
  null_blk: Fix: memory release when memory_backed=1
  blk-mq: fix blk_mq_hw_ctx active request accounting

Merge tag 'for_linus' of git://git./linux/kernel/git/mst/vhost

Pull virtio bug fixes from Michael Tsirkin:
"A bunch of fixes all over the place"

* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
  tools/virtio: use canonical ftrace path
  vhost_vdpa: support PACKED when setting-getting vring_base
  vhost: support PACKED when setting-getting vring_base
  vhost: Fix worker hangs due to missed wake up calls
  vhost: Fix crash during early vhost_transport_send_pkt calls
  vhost_net: revert upend_idx only on retriable error
  vhost_vdpa: tell vqs about the negotiated
  vdpa/mlx5: Fix hang when cvq commands are triggered during device unregister
  tools/virtio: Add .gitignore for ringtest
  tools/virtio: Fix arm64 ringtest compilation error
  vduse: avoid empty string for dev name
  vhost: use kzalloc() instead of kmalloc() followed by memset()

Merge tag 'ceph-for-6.4-rc6' of https://github.com/ceph/ceph-client

Pull ceph fixes from Ilya Dryomov:
"A fix for a potential data corruption in differential backup and
  snapshot-based mirroring scenarios in RBD and a reference counting
  fixup to avoid use-after-free in CephFS, all marked for stable"

* tag 'ceph-for-6.4-rc6' of https://github.com/ceph/ceph-client:
  ceph: fix use-after-free bug for inodes when flushing capsnaps
  rbd: get snapshot context after exclusive lock is ensured to be held
  rbd: move RBD_OBJ_FLAG_COPYUP_ENABLED flag setting

s390/dasd: Use correct lock while counting channel queue length

The lock around counting the channel queue length in the BIODASDINFO
ioctl was incorrectly changed to the dasd_block->queue_lock with commit
583d6535cb9d ("dasd: remove dead code"). This can lead to endless list
iterations and a subsequent crash.

The queue_lock is supposed to be used only for queue lists belonging to
dasd_block. For dasd_device related queue lists the ccwdev lock must be
used.

Fix the mentioned issues by correctly using the ccwdev lock instead of
the queue lock.

Fixes: 583d6535cb9d ("dasd: remove dead code")
Cc: stable@vger.kernel.org # v5.0+
Signed-off-by: Jan Höppner <hoeppner@linux.ibm.com>
Reviewed-by: Stefan Haberland <sth@linux.ibm.com>
Signed-off-by: Stefan Haberland <sth@linux.ibm.com>
Link: https://lore.kernel.org/r/20230609153750.1258763-2-sth@linux.ibm.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>

Merge tag 'riscv-for-linus-6.4-rc6' of git://git./linux/kernel/git/riscv/linux

Pull RISC-V fixes from Palmer Dabbelt:

- A fix to avoid ISA-disallowed privilege mappings that can result from
   WRITE+EXEC mmap requests from userspace.

- A fix for kfence to handle the huge pages.

- A fix to avoid converting misaligned VAs to huge pages.

- ARCH_HAS_NON_OVERLAPPING_ADDRESS_SPACE has been selected so kprobe
   can understand user pointers.

* tag 'riscv-for-linus-6.4-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
  riscv: fix kprobe __user string arg print fault issue
  riscv: Check the virtual alignment before choosing a map size
  riscv: Fix kfence now that the linear mapping can be backed by PUD/P4D/PGD
  riscv: mm: Ensure prot of VM_WRITE and VM_EXEC must be readable

Merge tag 's390-6.4-3' of git://git./linux/kernel/git/s390/linux

Pull s390 fixes from Alexander Gordeev:

- Avoid linker error for randomly generated config file that has
   CONFIG_BRANCH_PROFILE_NONE enabled and make it similar to riscv, x86
   and also to commit 4bf3ec384edf ("s390: disable branch profiling for
   vdso").

- Currently, if the device is offline and all the channel paths are
   either configured or varied offline, the associated subchannel gets
   unregistered. Don't unregister the subchannel, instead unregister
   offline device.

* tag 's390-6.4-3' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
  s390/purgatory: disable branch profiling
  s390/cio: unregister device when the only path is gone

Merge tag 'gpio-fixes-for-v6.4-rc6' of git://git./linux/kernel/git/brgl/linux

Pull gpio fixes from Bartosz Golaszewski:
"Two fixes for the GPIO testing module and one commit making Andy a
  reviewer for the GPIO subsystem:

   - fix a memory corruption bug in gpio-sim

   - fix inconsistencies in user-space configuration of gpio-sim

   - make Andy Shevchenko a reviewer for the GPIO subsystem"

* tag 'gpio-fixes-for-v6.4-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux:
  MAINTAINERS: add Andy Shevchenko as reviewer for the GPIO subsystem
  gpio: sim: quietly ignore configured lines outside the bank
  gpio: sim: fix memory corruption when adding named lines and unnamed hogs

tools/virtio: use canonical ftrace path

The canonical location for the tracefs filesystem is at /sys/kernel/tracing.

But, from Documentation/trace/ftrace.rst:

  Before 4.1, all ftrace tracing control files were within the debugfs
  file system, which is typically located at /sys/kernel/debug/tracing.
  For backward compatibility, when mounting the debugfs file system,
  the tracefs file system will be automatically mounted at:

  /sys/kernel/debug/tracing

A few spots in tools/virtio still refer to this older debugfs
path, so let's update them to avoid confusion.

Signed-off-by: Ross Zwisler <zwisler@google.com>
Message-Id: <20230215223350.2658616-6-zwisler@google.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Mukesh Ojha <quic_mojha@quicinc.com>

vhost_vdpa: support PACKED when setting-getting vring_base

Use the right structs for PACKED or split vqs when setting and
getting the vring base.

Fixes: 4c8cf31885f6 ("vhost: introduce vDPA-based backend")
Signed-off-by: Shannon Nelson <shannon.nelson@amd.com>
Message-Id: <20230424225031.18947-4-shannon.nelson@amd.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>

vhost: support PACKED when setting-getting vring_base

Use the right structs for PACKED or split vqs when setting and
getting the vring base.

Fixes: 4c8cf31885f6 ("vhost: introduce vDPA-based backend")
Signed-off-by: Shannon Nelson <shannon.nelson@amd.com>
Message-Id: <20230424225031.18947-3-shannon.nelson@amd.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>

Merge tag 'pinctrl-v6.4-2' of git://git./linux/kernel/git/linusw/linux-pinctrl

Pull pin control fix from Linus Walleij:
"A single fix for the Meson driver, nothing else has surfaced so far
this cycle"

* tag 'pinctrl-v6.4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: meson-axg: add missing GPIOA_18 gpio group

Merge tag 'sound-6.4-rc6' of git://git./linux/kernel/git/tiwai/sound

Pull sound fixes from Takashi Iwai:
"Lots of small fixes, and almost all are device-specific.

  A few of them are the fixes for the old regressions by the fast kctl
  lookups (introduced around 5.19). Others are ASoC simple-card fixes,
  selftest compile warning fixes, ASoC AMD quirks, various ASoC codec
  fixes as well as usual HD-audio quirks"

* tag 'sound-6.4-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (26 commits)
  ALSA: hda/realtek: Enable 4 amplifiers instead of 2 on a HP platform
  ALSA: hda: Fix kctl->id initialization
  ALSA: gus: Fix kctl->id initialization
  ALSA: cmipci: Fix kctl->id initialization
  ALSA: ymfpci: Fix kctl->id initialization
  ALSA: ice1712,ice1724: fix the kcontrol->id initialization
  ALSA: hda/realtek: Add quirk for Clevo NS50AU
  ALSA: hda/realtek: Add quirks for Asus ROG 2024 laptops using CS35L41
  ALSA: hda/realtek: Add "Intel Reference board" and "NUC 13" SSID in the ALC256
  ALSA: hda/realtek: Add Lenovo P3 Tower platform
  ALSA: hda/realtek: Add a quirk for HP Slim Desktop S01
  selftests: alsa: pcm-test: Fix compiler warnings about the format
  ASoC: fsl_sai: Enable BCI bit if SAI works on synchronous mode with BYP asserted
  ASoC: simple-card-utils: fix PCM constraint error check
  ASoC: cs35l56: Remove NULL check from cs35l56_sdw_dai_set_stream()
  ASoC: max98363: limit the number of channel to 1
  ASoC: max98363: Removed 32bit support
  ASoC: mediatek: mt8195: fix use-after-free in driver remove path
  ASoC: mediatek: mt8188: fix use-after-free in driver remove path
  ASoC: amd: yc: Add Thinkpad Neo14 to quirks list for acp6x
  ...

Merge tag 'ext4_for_linus_stable' of git://git./linux/kernel/git/tytso/ext4

Pull ext4 fix from Ted Ts'o:
"Fix an ext4 regression which breaks remounting r/w file systems that
  have the quota feature enabled"

* tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
  ext4: only check dquot_initialize_needed() when debugging
  Revert "ext4: don't clear SB_RDONLY when remounting r/w until quota is re-enabled"

Merge tag 'at24-fixes-for-v6.4-rc6' of git://git./linux/kernel/git/brgl/linux into i2c/for-current

at24 fixes for v6.4-rc6

- fix a Kconfig issue (we need to select REGMAP, not only REGMAP_I2C)

Merge tag 'imx-fixes-6.4-2' of git://git./linux/kernel/git/shawnguo/linux into arm/fixes

i.MX fixes for 6.4, round 2:

- Fix SPI CS pinmux for the final production version of imx8mn-beacon
  board.
- Fix GPIOs for USDHC2 CD and WP signals on imx8qm-mek board.
- Assign default clock rate for i.MX8 LPUARTs to fix UART failure.

* tag 'imx-fixes-6.4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
  arm64: dts: imx8mn-beacon: Fix SPI CS pinmux
  arm64: dts: imx8-ss-dma: assign default clock rate for lpuarts
  arm64: dts: imx8qm-mek: correct GPIOs for USDHC2 CD and WP signals

Link: https://lore.kernel.org/r/20230607141312.GU4199@dragon
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Merge tag 'drm-fixes-2023-06-09' of git://anongit.freedesktop.org/drm/drm

Pull drm fixes from Dave Airlie:
"Bit busier and a bit more scattered than usual. amdgpu is the main
  one, with ivpu and msm having a few fixes, then i915, exynos, ast,
  lima, radeon with some misc bits, but overall nothing standing out.

  fb-helper:
   - Fill in fb-helper vars more correctly

  amdgpu:
   - S0ix fixes
   - GPU reset fixes
   - SMU13 fixes
   - SMU11 fixes
   - Misc Display fixes
   - Revert RV/RV2/PCO clock counter changes
   - Fix Stoney xclk value
   - Fix reserved vram debug info

  radeon:
   - Fix a potential use after free

  i915:
   - CDCLK voltage fix for ADL-P
   - eDP wake sync pulse fix
   - Two error handling fixes to selftests

  exynos:
   - Fix wrong return in Exynos vidi driver
   - Fix use-after-free issue to Exynos g2d driver

  ast:
   - resume and modeset fixes for ast

  ivpu:
   - Assorted ivpu fixes

  lima:
   - lima context destroy fix

  msm:
   - Fix max segment size to address splat on newer a6xx
   - Disable PSR by default w/ modparam to re-enable, since there still
     seems to be a lingering issue
   - Fix HPD issue
   - Fix issue with unitialized GMU mutex"

* tag 'drm-fixes-2023-06-09' of git://anongit.freedesktop.org/drm/drm: (32 commits)
  drm/msm/a6xx: initialize GMU mutex earlier
  drm/msm/dp: enable HDP plugin/unplugged interrupts at hpd_enable/disable
  accel/ivpu: Fix sporadic VPU boot failure
  accel/ivpu: Do not use mutex_lock_interruptible
  accel/ivpu: Do not trigger extra VPU reset if the VPU is idle
  drm/amd/display: Reduce sdp bw after urgent to 90%
  drm/amdgpu: change reserved vram info print
  drm/amdgpu: fix xclk freq on CHIP_STONEY
  drm/radeon: fix race condition UAF in radeon_gem_set_domain_ioctl
  Revert "drm/amdgpu: switch to golden tsc registers for raven/raven2"
  Revert "drm/amdgpu: Differentiate between Raven2 and Raven/Picasso according to revision id"
  Revert "drm/amdgpu: change the reference clock for raven/raven2"
  drm/amd/display: add ODM case when looking for first split pipe
  drm/amd: Make lack of `ACPI_FADT_LOW_POWER_S0` or `CONFIG_AMD_PMC` louder during suspend path
  drm/amd/pm: conditionally disable pcie lane switching for some sienna_cichlid SKUs
  drm/amd/pm: Fix power context allocation in SMU13
  drm/amdgpu: fix Null pointer dereference error in amdgpu_device_recover_vram
  drm/amd: Disallow s0ix without BIOS support again
  drm/i915/selftests: Add some missing error propagation
  drm/exynos: fix race condition UAF in exynos_g2d_exec_ioctl
  ...

Merge tag 'cgroup-for-6.4-rc5-fixes' of git://git./linux/kernel/git/tj/cgroup

Pull cgroup fixes from Tejun Heo:

- Fix css_set reference leaks on fork failures

- Fix CPU hotplug locking in cgroup_transfer_tasks() which is used by
   cgroup1 cpuset

- Doc update

* tag 'cgroup-for-6.4-rc5-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
  cgroup: Documentation: Clarify usage of memory limits
  cgroup: always put cset in cgroup_css_set_put_fork
  cgroup: fix missing cpus_read_{lock,unlock}() in cgroup_transfer_tasks()

Merge tag 'drm-msm-fixes-2023-06-08' of https://gitlab.freedesktop.org/drm/msm into drm-fixes

A few more late fixes for v6.4-rc6

+ Fix max segment size to address splat on newer a6xx
+ Disable PSR by default w/ modparam to re-enable, since there
still seems to be a lingering issue
+ Fix HPD issue
+ Fix issue with unitialized GMU mutex

Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rob Clark <robdclark@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/CAF6AEGufjVZRNT6YfQ7YUXFC7Cz95wdLF7QHAYkiGfp+3Xc3DQ@mail.gmail.com

drm/msm/a6xx: initialize GMU mutex earlier

Move GMU mutex initialization earlier to make sure that it is always
initialized. a6xx_destroy can be called from ther failure path before
GMU initialization.

This fixes the following backtrace:

------------[ cut here ]------------
DEBUG_LOCKS_WARN_ON(lock->magic != lock)
WARNING: CPU: 0 PID: 58 at kernel/locking/mutex.c:582 __mutex_lock+0x1ec/0x3d0
Modules linked in:
CPU: 0 PID: 58 Comm: kworker/u16:1 Not tainted 6.3.0-rc5-00155-g187c06436519 #565
Hardware name: Qualcomm Technologies, Inc. SM8350 HDK (DT)
Workqueue: events_unbound deferred_probe_work_func
pstate: 60400005 (nZCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : __mutex_lock+0x1ec/0x3d0
lr : __mutex_lock+0x1ec/0x3d0
sp : ffff800008993620
x29: ffff800008993620 x28: 0000000000000002 x27: ffff47b253c52800
x26: 0000000001000606 x25: ffff47b240bb2810 x24: fffffffffffffff4
x23: 0000000000000000 x22: ffffc38bba15ac14 x21: 0000000000000002
x20: ffff800008993690 x19: ffff47b2430cc668 x18: fffffffffffe98f0
x17: 6f74616c75676572 x16: 20796d6d75642067 x15: 0000000000000038
x14: 0000000000000000 x13: ffffc38bbba050b8 x12: 0000000000000666
x11: 0000000000000222 x10: ffffc38bbba603e8 x9 : ffffc38bbba050b8
x8 : 00000000ffffefff x7 : ffffc38bbba5d0b8 x6 : 0000000000000222
x5 : 000000000000bff4 x4 : 40000000fffff222 x3 : 0000000000000000
x2 : 0000000000000000 x1 : 0000000000000000 x0 : ffff47b240cb1880
Call trace:
__mutex_lock+0x1ec/0x3d0
mutex_lock_nested+0x2c/0x38
a6xx_destroy+0xa0/0x138
a6xx_gpu_init+0x41c/0x618
adreno_bind+0x188/0x290
component_bind_all+0x118/0x248
msm_drm_bind+0x1c0/0x670
try_to_bring_up_aggregate_device+0x164/0x1d0
__component_add+0xa8/0x16c
component_add+0x14/0x20
dsi_dev_attach+0x20/0x2c
dsi_host_attach+0x9c/0x144
devm_mipi_dsi_attach+0x34/0xac
lt9611uxc_attach_dsi.isra.0+0x84/0xfc
lt9611uxc_probe+0x5b8/0x67c
i2c_device_probe+0x1ac/0x358
really_probe+0x148/0x2ac
__driver_probe_device+0x78/0xe0
driver_probe_device+0x3c/0x160
__device_attach_driver+0xb8/0x138
bus_for_each_drv+0x84/0xe0
__device_attach+0x9c/0x188
device_initial_probe+0x14/0x20
bus_probe_device+0xac/0xb0
deferred_probe_work_func+0x8c/0xc8
process_one_work+0x2bc/0x594
worker_thread+0x228/0x438
kthread+0x108/0x10c
ret_from_fork+0x10/0x20
irq event stamp: 299345
hardirqs last enabled at (299345): [<ffffc38bb9ba61e4>] put_cpu_partial+0x1c8/0x22c
hardirqs last disabled at (299344): [<ffffc38bb9ba61dc>] put_cpu_partial+0x1c0/0x22c
softirqs last enabled at (296752): [<ffffc38bb9890434>] _stext+0x434/0x4e8
softirqs last disabled at (296741): [<ffffc38bb989669c>] ____do_softirq+0x10/0x1c
---[ end trace 0000000000000000 ]---

Fixes: 4cd15a3e8b36 ("drm/msm/a6xx: Make GPU destroy a bit safer")
Cc: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Patchwork: https://patchwork.freedesktop.org/patch/531540/
Signed-off-by: Rob Clark <robdclark@chromium.org>

drm/msm/dp: enable HDP plugin/unplugged interrupts at hpd_enable/disable

The internal_hpd flag is set to true by dp_bridge_hpd_enable() and set to
false by dp_bridge_hpd_disable() to handle GPIO pinmuxed into DP controller
case. HDP related interrupts can not be enabled until internal_hpd is set
to true. At current implementation dp_display_config_hpd() will initialize
DP host controller first followed by enabling HDP related interrupts if
internal_hpd was true at that time. Enable HDP related interrupts depends on
internal_hpd status may leave system with DP driver host is in running state
but without HDP related interrupts being enabled. This will prevent external
display from being detected. Eliminated this dependency by moving HDP related
interrupts enable/disable be done at dp_bridge_hpd_enable/disable() directly
regardless of internal_hpd status.

Changes in V3:
-- dp_catalog_ctrl_hpd_enable() and dp_catalog_ctrl_hpd_disable()
-- rewording ocmmit text

Changes in V4:
-- replace dp_display_config_hpd() with dp_display_host_start()
-- move enable_irq() at dp_display_host_start();

Changes in V5:
-- replace dp_display_host_start() with dp_display_host_init()

Changes in V6:
-- squash remove enable_irq() and disable_irq()

Fixes: cd198caddea7 ("drm/msm/dp: Rely on hpd_enable/disable callbacks")
Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Tested-by: Leonard Lausen <leonard@lausen.nl> # on sc7180 lazor
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Tested-by: Bjorn Andersson <andersson@kernel.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Link: https://lore.kernel.org/r/1684878756-17830-1-git-send-email-quic_khsieh@quicinc.com
Signed-off-by: Rob Clark <robdclark@chromium.org>

Merge tag 'drm-misc-fixes-2023-06-08' of git://anongit.freedesktop.org/drm/drm-misc into drm-fixes

drm-misc-fixes for v6.4-rc6:
- resume and modeset fixes for ast.
- Fill in fb-helper vars more correctly.
- Assorted ivpu fixes.
- lima context destroy fix.

Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/ea6b88ec-b653-3781-0b68-cd0275c27923@linux.intel.com

Merge tag 'exynos-drm-fixes-for-v6.4-rc6' of git://git./linux/kernel/git/daeinki/drm-exynos into drm-fixes

Two fixups
- Fix wrong return in Exynos vidi driver.
- Fix use-after-free issue to Exynos g2d driver.

Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Inki Dae <inki.dae@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230607043148.43303-1-inki.dae@samsung.com

Merge tag 'drm-intel-fixes-2023-06-08' of git://anongit.freedesktop.org/drm/drm-intel into drm-fixes

CDCLK voltage fix for ADL-P and eDP wake sync pulse fix.
Two error handling fixes to selftests (to appease static checkers)

Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/ZIGUHBz7+LsqN2nm@jlahtine-mobl.ger.corp.intel.com

Merge tag 'amd-drm-fixes-6.4-2023-06-07' of https://gitlab.freedesktop.org/agd5f/linux into drm-fixes

amd-drm-fixes-6.4-2023-06-07:

amdgpu:
- S0ix fixes
- GPU reset fixes
- SMU13 fixes
- SMU11 fixes
- Misc Display fixes
- Revert RV/RV2/PCO clock counter changes
- Fix Stoney xclk value
- Fix reserved vram debug info

radeon:
- Fix a potential use after free

Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexander.deucher@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230607213740.7723-1-alexander.deucher@amd.com

Merge tag 'arm64-fixes' of git://git./linux/kernel/git/arm64/linux

Pull arm64 fixes from Will Deacon:
"Two tiny arm64 fixes for -rc6.

  One fixes a build breakage when MAX_ORDER can be nonsensical if
  CONFIG_EXPERT=y and the other fixes the address masking for perf's
  page fault software events so that it is consistent amongst them:

   - Fix build breakage due to bogus MAX_ORDER definitions on !4k pages

   - Avoid masking fault address for perf software events"

* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
  arm64: mm: pass original fault address to handle_mm_fault() in PER_VMA_LOCK block
  arm64: Remove the ARCH_FORCE_MAX_ORDER config input prompt

vhost: Fix worker hangs due to missed wake up calls

We can race where we have added work to the work_list, but
vhost_task_fn has passed that check but not yet set us into
TASK_INTERRUPTIBLE. wake_up_process will see us in TASK_RUNNING and
just return.

This bug was intoduced in commit f9010dbdce91 ("fork, vhost: Use
CLONE_THREAD to fix freezer/ps regression") when I moved the setting
of TASK_INTERRUPTIBLE to simplfy the code and avoid get_signal from
logging warnings about being in the wrong state. This moves the setting
of TASK_INTERRUPTIBLE back to before we test if we need to stop the
task to avoid a possible race there as well. We then have vhost_worker
set TASK_RUNNING if it finds work similar to before.

Fixes: f9010dbdce91 ("fork, vhost: Use CLONE_THREAD to fix freezer/ps regression")
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Message-Id: <20230607192338.6041-3-michael.christie@oracle.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>

vhost: Fix crash during early vhost_transport_send_pkt calls

If userspace does VHOST_VSOCK_SET_GUEST_CID before VHOST_SET_OWNER we
can race where:
1. thread0 calls vhost_transport_send_pkt -> vhost_work_queue
2. thread1 does VHOST_SET_OWNER which calls vhost_worker_create.
3. vhost_worker_create will set the dev->worker pointer before setting
the worker->vtsk pointer.
4. thread0's vhost_work_queue will see the dev->worker pointer is
set and try to call vhost_task_wake using not yet set worker->vtsk
pointer.
5. We then crash since vtsk is NULL.

Before commit 6e890c5d5021 ("vhost: use vhost_tasks for worker
threads"), we only had the worker pointer so we could just check it to
see if VHOST_SET_OWNER has been done. After that commit we have the
vhost_worker and vhost_task pointer, so we can now hit the bug above.

This patch embeds the vhost_worker in the vhost_dev and moves the work
list initialization back to vhost_dev_init, so we can just check the
worker.vtsk pointer to check if VHOST_SET_OWNER has been done like
before.

Fixes: 6e890c5d5021 ("vhost: use vhost_tasks for worker threads")
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Message-Id: <20230607192338.6041-2-michael.christie@oracle.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reported-by: syzbot+d0d442c22fa8db45ff0e@syzkaller.appspotmail.com
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>

vhost_net: revert upend_idx only on retriable error

Fix possible virtqueue used buffers leak and corresponding stuck
in case of temporary -EIO from sendmsg() which is produced by
tun driver while backend device is not up.

In case of no-retriable error and zcopy do not revert upend_idx
to pass packet data (that is update used_idx in corresponding
vhost_zerocopy_signal_used()) as if packet data has been
transferred successfully.

v2: set vq->heads[ubuf->desc].len equal to VHOST_DMA_DONE_LEN
in case of fake successful transmit.

Signed-off-by: Andrey Smetanin <asmetanin@yandex-team.ru>
Message-Id: <20230424204411.24888-1-asmetanin@yandex-team.ru>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Andrey Smetanin <asmetanin@yandex-team.ru>
Acked-by: Jason Wang <jasowang@redhat.com>

vhost_vdpa: tell vqs about the negotiated

As is done in the net, iscsi, and vsock vhost support, let the vdpa vqs
know about the features that have been negotiated. This allows vhost
to more safely make decisions based on the features, such as when using
PACKED vs split queues.

Signed-off-by: Shannon Nelson <shannon.nelson@amd.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20230424225031.18947-2-shannon.nelson@amd.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>

vdpa/mlx5: Fix hang when cvq commands are triggered during device unregister

Currently the vdpa device is unregistered after the workqueue that
processes vq commands is disabled. However, the device unregister
process can still send commands to the cvq (a vlan delete for example)
which leads to a hang because the handing workqueue has been disabled
and the command never finishes:

[ 2263.095764] rcu: INFO: rcu_sched self-detected stall on CPU
[ 2263.096307] rcu:        9-....: (5250 ticks this GP) idle=dac4/1/0x4000000000000000 softirq=111009/111009 fqs=2544
[ 2263.097154] rcu:        (t=5251 jiffies g=393549 q=347 ncpus=10)
[ 2263.097648] CPU: 9 PID: 94300 Comm: kworker/u20:2 Not tainted 6.3.0-rc6_for_upstream_min_debug_2023_04_14_00_02 #1
[ 2263.098535] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014
[ 2263.099481] Workqueue: mlx5_events mlx5_vhca_state_work_handler [mlx5_core]
[ 2263.100143] RIP: 0010:virtnet_send_command+0x109/0x170
[ 2263.100621] Code: 1d df f5 ff 85 c0 78 5c 48 8b 7b 08 e8 d0 c5 f5 ff 84 c0 75 11 eb 22 48 8b 7b 08 e8 01 b7 f5 ff 84 c0 75 15 f3 90 48 8b 7b 08 <48> 8d 74 24 04 e8 8d c5 f5 ff 48 85 c0 74 de 48 8b 83 f8 00 00 00
[ 2263.102148] RSP: 0018:ffff888139cf36e8 EFLAGS: 00000246
[ 2263.102624] RAX: 0000000000000000 RBX: ffff888166bea940 RCX: 0000000000000001
[ 2263.103244] RDX: 0000000000000000 RSI: ffff888139cf36ec RDI: ffff888146763800
[ 2263.103864] RBP: ffff888139cf3710 R08: ffff88810d201000 R09: 0000000000000000
[ 2263.104473] R10: 0000000000000002 R11: 0000000000000003 R12: 0000000000000002
[ 2263.105082] R13: 0000000000000002 R14: ffff888114528400 R15: ffff888166bea000
[ 2263.105689] FS:  0000000000000000(0000) GS:ffff88852cc80000(0000) knlGS:0000000000000000
[ 2263.106404] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 2263.106925] CR2: 00007f31f394b000 CR3: 000000010615b006 CR4: 0000000000370ea0
[ 2263.107542] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 2263.108163] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[ 2263.108769] Call Trace:
[ 2263.109059]  <TASK>
[ 2263.109320]  ? check_preempt_wakeup+0x11f/0x230
[ 2263.109750]  virtnet_vlan_rx_kill_vid+0x5a/0xa0
[ 2263.110180]  vlan_vid_del+0x9c/0x170
[ 2263.110546]  vlan_device_event+0x351/0x760 [8021q]
[ 2263.111004]  raw_notifier_call_chain+0x41/0x60
[ 2263.111426]  dev_close_many+0xcb/0x120
[ 2263.111808]  unregister_netdevice_many_notify+0x130/0x770
[ 2263.112297]  ? wq_worker_running+0xa/0x30
[ 2263.112688]  unregister_netdevice_queue+0x89/0xc0
[ 2263.113128]  unregister_netdev+0x18/0x20
[ 2263.113512]  virtnet_remove+0x4f/0x230
[ 2263.113885]  virtio_dev_remove+0x31/0x70
[ 2263.114273]  device_release_driver_internal+0x18f/0x1f0
[ 2263.114746]  bus_remove_device+0xc6/0x130
[ 2263.115146]  device_del+0x173/0x3c0
[ 2263.115502]  ? kernfs_find_ns+0x35/0xd0
[ 2263.115895]  device_unregister+0x1a/0x60
[ 2263.116279]  unregister_virtio_device+0x11/0x20
[ 2263.116706]  device_release_driver_internal+0x18f/0x1f0
[ 2263.117182]  bus_remove_device+0xc6/0x130
[ 2263.117576]  device_del+0x173/0x3c0
[ 2263.117929]  ? vdpa_dev_remove+0x20/0x20 [vdpa]
[ 2263.118364]  device_unregister+0x1a/0x60
[ 2263.118752]  mlx5_vdpa_dev_del+0x4c/0x80 [mlx5_vdpa]
[ 2263.119232]  vdpa_match_remove+0x21/0x30 [vdpa]
[ 2263.119663]  bus_for_each_dev+0x71/0xc0
[ 2263.120054]  vdpa_mgmtdev_unregister+0x57/0x70 [vdpa]
[ 2263.120520]  mlx5v_remove+0x12/0x20 [mlx5_vdpa]
[ 2263.120953]  auxiliary_bus_remove+0x18/0x30
[ 2263.121356]  device_release_driver_internal+0x18f/0x1f0
[ 2263.121830]  bus_remove_device+0xc6/0x130
[ 2263.122223]  device_del+0x173/0x3c0
[ 2263.122581]  ? devl_param_driverinit_value_get+0x29/0x90
[ 2263.123070]  mlx5_rescan_drivers_locked+0xc4/0x2d0 [mlx5_core]
[ 2263.123633]  mlx5_unregister_device+0x54/0x80 [mlx5_core]
[ 2263.124169]  mlx5_uninit_one+0x54/0x150 [mlx5_core]
[ 2263.124656]  mlx5_sf_dev_remove+0x45/0x90 [mlx5_core]
[ 2263.125153]  auxiliary_bus_remove+0x18/0x30
[ 2263.125560]  device_release_driver_internal+0x18f/0x1f0
[ 2263.126052]  bus_remove_device+0xc6/0x130
[ 2263.126451]  device_del+0x173/0x3c0
[ 2263.126815]  mlx5_sf_dev_remove+0x39/0xf0 [mlx5_core]
[ 2263.127318]  mlx5_sf_dev_state_change_handler+0x178/0x270 [mlx5_core]
[ 2263.127920]  blocking_notifier_call_chain+0x5a/0x80
[ 2263.128379]  mlx5_vhca_state_work_handler+0x151/0x200 [mlx5_core]
[ 2263.128951]  process_one_work+0x1bb/0x3c0
[ 2263.129355]  ? process_one_work+0x3c0/0x3c0
[ 2263.129766]  worker_thread+0x4d/0x3c0
[ 2263.130140]  ? process_one_work+0x3c0/0x3c0
[ 2263.130548]  kthread+0xb9/0xe0
[ 2263.130895]  ? kthread_complete_and_exit+0x20/0x20
[ 2263.131349]  ret_from_fork+0x1f/0x30
[ 2263.131717]  </TASK>

The fix is to disable and destroy the workqueue after the device
unregister. It is expected that vhost will not trigger kicks after
the unregister. But even if it would, the wq is disabled already by
setting the pointer to NULL (done so in the referenced commit).

Fixes: ad6dc1daaf29 ("vdpa/mlx5: Avoid processing works if workqueue was destroyed")
Signed-off-by: Dragos Tatulea <dtatulea@nvidia.com>
Message-Id: <20230516095800.3549932-1-dtatulea@nvidia.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Acked-by: Jason Wang <jasowang@redhat.com>

tools/virtio: Add .gitignore for ringtest

Ignore executables for ringtest.

Signed-off-by: Rong Tao <rongtao@cestc.cn>
Message-Id: <tencent_C121802C93CB4095C6D7D95113442E830A07@qq.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>

tools/virtio: Fix arm64 ringtest compilation error

Add cpu_relax() for arm64 instead of directly assert(), and add assert.h
header file. Also, add smp_wmb and smp_mb for arm64.

Compilation error as follows, avoid __always_inline undefined.

    $ make
    cc -Wall -pthread -O2 -ggdb -flto -fwhole-program -c -o ring.o ring.c
    In file included from ring.c:10:
    main.h: In function ‘busy_wait’:
    main.h:99:21: warning: implicit declaration of function ‘assert’
    [-Wimplicit-function-declaration]
    99 | #define cpu_relax() assert(0)
        |                     ^~~~~~
    main.h:107:17: note: in expansion of macro ‘cpu_relax’
    107 |                 cpu_relax();
        |                 ^~~~~~~~~
    main.h:12:1: note: ‘assert’ is defined in header ‘<assert.h>’; did you
    forget to ‘#include <assert.h>’?
    11 | #include <stdbool.h>
    +++ |+#include <assert.h>
    12 |
    main.h: At top level:
    main.h:143:23: error: expected ‘;’ before ‘void’
    143 | static __always_inline
        |                       ^
        |                       ;
    144 | void __read_once_size(const volatile void *p, void *res, int
    size)
        | ~~~~
    main.h:158:23: error: expected ‘;’ before ‘void’
    158 | static __always_inline void __write_once_size(volatile void *p,
    void *res, int size)
        |                       ^~~~~
        |                       ;
    make: *** [<builtin>: ring.o] Error 1

Signed-off-by: Rong Tao <rongtao@cestc.cn>
Message-Id: <tencent_F53E159DD7925174445D830DA19FACF44B07@qq.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>

vduse: avoid empty string for dev name

Syzkaller hits a kernel WARN when the first character of the dev name
provided is NULL. Solution is to add a NULL check before calling
cdev_device_add() in vduse_create_dev().

kobject: (0000000072042169): attempted to be registered with empty name!
WARNING: CPU: 0 PID: 112695 at lib/kobject.c:236
Call Trace:
kobject_add_varg linux/src/lib/kobject.c:390 [inline]
kobject_add+0xf6/0x150 linux/src/lib/kobject.c:442
device_add+0x28f/0xc20 linux/src/drivers/base/core.c:2167
cdev_device_add+0x83/0xc0 linux/src/fs/char_dev.c:546
vduse_create_dev linux/src/drivers/vdpa/vdpa_user/vduse_dev.c:2254 [inline]
vduse_ioctl+0x7b5/0xf30 linux/src/drivers/vdpa/vdpa_user/vduse_dev.c:2316
vfs_ioctl linux/src/fs/ioctl.c:47 [inline]
file_ioctl linux/src/fs/ioctl.c:510 [inline]
do_vfs_ioctl+0x14b/0xa80 linux/src/fs/ioctl.c:697
ksys_ioctl+0x7c/0xa0 linux/src/fs/ioctl.c:714
__do_sys_ioctl linux/src/fs/ioctl.c:721 [inline]
__se_sys_ioctl linux/src/fs/ioctl.c:719 [inline]
__x64_sys_ioctl+0x42/0x50 linux/src/fs/ioctl.c:719
do_syscall_64+0x94/0x330 linux/src/arch/x86/entry/common.c:291
entry_SYSCALL_64_after_hwframe+0x44/0xa9

Fixes: c8a6153b6c59 ("vduse: Introduce VDUSE - vDPA Device in Userspace")
Cc: "Xie Yongji" <xieyongji@bytedance.com>
Reported-by: Xianjun Zeng <zengxianjun@bytedance.com>
Signed-off-by: Sheng Zhao <sheng.zhao@bytedance.com>
Message-Id: <20230530033626.1266794-1-sheng.zhao@bytedance.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Xie Yongji <xieyongji@bytedance.com>
Cc: "Michael S. Tsirkin"<mst@redhat.com>, "Jason Wang"<jasowang@redhat.com>,
Reviewed-by: Xie Yongji <xieyongji@bytedance.com>

MAINTAINERS: Add entries for Renesas RZ/V2M I2C driver

Add the MAINTAINERS entries for the Renesas RZ/V2M I2C driver.

Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Acked-by: Fabrizio Castro <fabrizio.castro.jz@renesas.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

riscv: fix kprobe __user string arg print fault issue

On riscv qemu platform, when add kprobe event on do_sys_open() to show
filename string arg, it just print fault as follow:

echo 'p:myprobe do_sys_open dfd=$arg1 filename=+0($arg2):string flags=$arg3
mode=$arg4' > kprobe_events

bash-166     [000] ...1.   360.195367: myprobe: (do_sys_open+0x0/0x84)
dfd=0xffffffffffffff9c filename=(fault) flags=0x8241 mode=0x1b6

bash-166     [000] ...1.   360.219369: myprobe: (do_sys_open+0x0/0x84)
dfd=0xffffffffffffff9c filename=(fault) flags=0x8241 mode=0x1b6

bash-191     [000] ...1.   360.378827: myprobe: (do_sys_open+0x0/0x84)
dfd=0xffffffffffffff9c filename=(fault) flags=0x98800 mode=0x0

As riscv do not select ARCH_HAS_NON_OVERLAPPING_ADDRESS_SPACE,
the +0($arg2) addr is processed as a kernel address though it is a
userspace address, cause the above filename=(fault) print. So select
ARCH_HAS_NON_OVERLAPPING_ADDRESS_SPACE to avoid the issue, after that the
kprobe trace is ok as below:

bash-166     [000] ...1.    96.767641: myprobe: (do_sys_open+0x0/0x84)
dfd=0xffffffffffffff9c filename="/dev/null" flags=0x8241 mode=0x1b6

bash-166     [000] ...1.    96.793751: myprobe: (do_sys_open+0x0/0x84)
dfd=0xffffffffffffff9c filename="/dev/null" flags=0x8241 mode=0x1b6

bash-177     [000] ...1.    96.962354: myprobe: (do_sys_open+0x0/0x84)
dfd=0xffffffffffffff9c filename="/sys/kernel/debug/tracing/events/kprobes/"
flags=0x98800 mode=0x0

Signed-off-by: Ruan Jinjie <ruanjinjie@huawei.com>
Acked-by: Björn Töpel <bjorn@rivosinc.com>
Fixes: 0ebeea8ca8a4 ("bpf: Restrict bpf_probe_read{, str}() only to archs where they work")
Link: https://lore.kernel.org/r/20230504072910.3742842-1-ruanjinjie@huawei.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>

Merge tag 'net-6.4-rc6' of git://git./linux/kernel/git/netdev/net

Pull networking fixes from Paolo Abeni:
"Including fixes from can, wifi, netfilter, bluetooth and ebpf.

  Current release - regressions:

   - bpf: sockmap: avoid potential NULL dereference in
     sk_psock_verdict_data_ready()

   - wifi: iwlwifi: fix -Warray-bounds bug in iwl_mvm_wait_d3_notif()

   - phylink: actually fix ksettings_set() ethtool call

   - eth: dwmac-qcom-ethqos: fix a regression on EMAC < 3

  Current release - new code bugs:

   - wifi: mt76: fix possible NULL pointer dereference in
     mt7996_mac_write_txwi()

  Previous releases - regressions:

   - netfilter: fix NULL pointer dereference in nf_confirm_cthelper

   - wifi: rtw88/rtw89: correct PS calculation for SUPPORTS_DYNAMIC_PS

   - openvswitch: fix upcall counter access before allocation

   - bluetooth:
      - fix use-after-free in hci_remove_ltk/hci_remove_irk
      - fix l2cap_disconnect_req deadlock

   - nic: bnxt_en: prevent kernel panic when receiving unexpected
     PHC_UPDATE event

  Previous releases - always broken:

   - core: annotate rfs lockless accesses

   - sched: fq_pie: ensure reasonable TCA_FQ_PIE_QUANTUM values

   - netfilter: add null check for nla_nest_start_noflag() in
     nft_dump_basechain_hook()

   - bpf: fix UAF in task local storage

   - ipv4: ping_group_range: allow GID from 2147483648 to 4294967294

   - ipv6: rpl: fix route of death.

   - tcp: gso: really support BIG TCP

   - mptcp: fixes for user-space PM address advertisement

   - smc: avoid to access invalid RMBs' MRs in SMCRv1 ADD LINK CONT

   - can: avoid possible use-after-free when j1939_can_rx_register fails

   - batman-adv: fix UaF while rescheduling delayed work

   - eth: qede: fix scheduling while atomic

   - eth: ice: make writes to /dev/gnssX synchronous"

* tag 'net-6.4-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (83 commits)
  bnxt_en: Implement .set_port / .unset_port UDP tunnel callbacks
  bnxt_en: Prevent kernel panic when receiving unexpected PHC_UPDATE event
  bnxt_en: Skip firmware fatal error recovery if chip is not accessible
  bnxt_en: Query default VLAN before VNIC setup on a VF
  bnxt_en: Don't issue AP reset during ethtool's reset operation
  bnxt_en: Fix bnxt_hwrm_update_rss_hash_cfg()
  net: bcmgenet: Fix EEE implementation
  eth: ixgbe: fix the wake condition
  eth: bnxt: fix the wake condition
  lib: cpu_rmap: Fix potential use-after-free in irq_cpu_rmap_release()
  bpf: Add extra path pointer check to d_path helper
  net: sched: fix possible refcount leak in tc_chain_tmplt_add()
  net: sched: act_police: fix sparse errors in tcf_police_dump()
  net: openvswitch: fix upcall counter access before allocation
  net: sched: move rtm_tca_policy declaration to include file
  ice: make writes to /dev/gnssX synchronous
  net: sched: add rcu annotations around qdisc->qdisc_sleeping
  rfs: annotate lockless accesses to RFS sock flow table
  rfs: annotate lockless accesses to sk->sk_rxhash
  virtio_net: use control_buf for coalesce params
  ...

Merge tag 'xfs-6.4-rc5-fixes' of git://git./fs/xfs/xfs-linux

Pull xfs fixes from Dave Chinner:
"These are a set of regression fixes discovered on recent kernels. I
  was hoping to send this to you a week and half ago, but events out of
  my control delayed finalising the changes until early this week.

  Whilst the diffstat looks large for this stage of the merge window, a
  large chunk of it comes from moving the guts of one function from one
  file to another i.e. it's the same code, it is just run in a different
  context where it is safe to hold a specific lock. Otherwise the
  individual changes are relatively small and straigtht forward.

  Summary:

   - Propagate unlinked inode list corruption back up to log recovery
     (regression fix)

   - improve corruption detection for AGFL entries, AGFL indexes and
     XEFI extents (syzkaller fuzzer oops report)

   - Avoid double perag reference release (regression fix)

   - Improve extent merging detection in scrub (regression fix)

   - Fix a new undefined high bit shift (regression fix)

   - Fix for AGF vs inode cluster buffer deadlock (regression fix)"

* tag 'xfs-6.4-rc5-fixes' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
  xfs: collect errors from inodegc for unlinked inode recovery
  xfs: validate block number being freed before adding to xefi
  xfs: validity check agbnos on the AGFL
  xfs: fix agf/agfl verification on v4 filesystems
  xfs: fix double xfs_perag_rele() in xfs_filestream_pick_ag()
  xfs: fix broken logic when detecting mergeable bmap records
  xfs: Fix undefined behavior of shift into sign bit
  xfs: fix AGF vs inode cluster buffer deadlock
  xfs: defered work could create precommits
  xfs: restore allocation trylock iteration
  xfs: buffer pins need to hold a buffer reference

ext4: only check dquot_initialize_needed() when debugging

ext4_xattr_block_set() relies on its caller to call dquot_initialize()
on the inode.  To assure that this has happened there are WARN_ON
checks.  Unfortunately, this is subject to false positives if there is
an antagonist thread which is flipping the file system at high rates
between r/o and rw.  So only do the check if EXT4_XATTR_DEBUG is
enabled.

Link: https://lore.kernel.org/r/20230608044056.GA1418535@mit.edu
Signed-off-by: Theodore Ts'o <tytso@mit.edu>

Revert "ext4: don't clear SB_RDONLY when remounting r/w until quota is re-enabled"

This reverts commit a44be64bbecb15a452496f60db6eacfee2b59c79.

Link: https://lore.kernel.org/r/653b3359-2005-21b1-039d-c55ca4cffdcc@gmail.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>

soundwire: stream: Add missing clear of alloc_slave_rt

The current path that skips allocating the slave runtime does not clear
the alloc_slave_rt flag, this is clearly incorrect. Add the missing
clear, so the runtime won't be erroneously cleaned up.

Fixes: f3016b891c8c ("soundwire: stream: sdw_stream_add_ functions can be called multiple times")
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230602101140.2040141-1-ckeepax@opensource.cirrus.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>

Merge branch 'bnxt_en-bug-fixes'

Michael Chan says:

====================
bnxt_en: Bug fixes

This patchset has the following fixes for bnxt_en:

1. Add missing VNIC ID parameter in the FW message when getting an
updated RSS configuration from the FW.

2. Fix a warning when doing ethtool reset on newer chips.

3. Fix VLAN issue on a VF when a default VLAN is assigned.

4. Fix a problem during DPC (Downstream Port containment) scenario.

5. Fix a NULL pointer dereference when receiving a PTP event from FW.

6. Fix VXLAN/Geneve UDP port delete/add with newer FW.
====================

Link: https://lore.kernel.org/r/20230607075409.228450-1-michael.chan@broadcom.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

bnxt_en: Implement .set_port / .unset_port UDP tunnel callbacks

As per the new udp tunnel framework, drivers which need to know the
details of a port entry (i.e. port type) when it gets deleted should
use the .set_port / .unset_port callbacks.

Implementing the current .udp_tunnel_sync callback would mean that the
deleted tunnel port entry would be all zeros. This used to work on
older firmware because it would not check the input when deleting a
tunnel port. With newer firmware, the delete will now fail and
subsequent tunnel port allocation will fail as a result.

Fixes: 442a35a5a7aa ("bnxt: convert to new udp_tunnel_nic infra")
Reviewed-by: Kalesh Anakkur Purayil <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

bnxt_en: Prevent kernel panic when receiving unexpected PHC_UPDATE event

The firmware can send PHC_RTC_UPDATE async event on a PF that may not
have PTP registered. In such a case, there will be a null pointer
deference for bp->ptp_cfg when we try to handle the event.

Fix it by not registering for this event with the firmware if !bp->ptp_cfg.
Also, check that bp->ptp_cfg is valid before proceeding when we receive
the event.

Fixes: 8bcf6f04d4a5 ("bnxt_en: Handle async event when the PHC is updated in RTC mode")
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

bnxt_en: Skip firmware fatal error recovery if chip is not accessible

Driver starts firmware fatal error recovery by detecting
heartbeat failure or fw reset count register changing. But
these checks are not reliable if the device is not accessible.
This can happen while DPC (Downstream Port containment) is in
progress. Skip firmware fatal recovery if pci_device_is_present()
returns false.

Fixes: acfb50e4e773 ("bnxt_en: Add FW fatal devlink_health_reporter.")
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Vikas Gupta <vikas.gupta@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

bnxt_en: Query default VLAN before VNIC setup on a VF

We need to call bnxt_hwrm_func_qcfg() on a VF to query the default
VLAN that may be setup by the PF.  If a default VLAN is enabled,
the VF cannot support VLAN acceleration on the receive side and
the VNIC must be setup to strip out the default VLAN tag.  If a
default VLAN is not enabled, the VF can support VLAN acceleration
on the receive side.  The VNIC should be set up to strip or not
strip the VLAN based on the RX VLAN acceleration setting.

Without this call to determine the default VLAN before calling
bnxt_setup_vnic(), the VNIC may not be set up correctly.  For
example, bnxt_setup_vnic() may set up to strip the VLAN tag based
on stale default VLAN information.  If RX VLAN acceleration is
not enabled, the VLAN tag will be incorrectly stripped and the
RX data path will not work correctly.

Fixes: cf6645f8ebc6 ("bnxt_en: Add function for VF driver to query default VLAN.")
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

bnxt_en: Don't issue AP reset during ethtool's reset operation

Only older NIC controller's firmware uses the PROC AP reset type.
Firmware on 5731X/5741X and newer chips does not support this reset
type. When bnxt_reset() issues a series of resets, this PROC AP
reset may actually fail on these newer chips because the firmware
is not ready to accept this unsupported command yet. Avoid this
unnecessary error by skipping this reset type on chips that don't
support it.

Fixes: 7a13240e3718 ("bnxt_en: fix ethtool_reset_flags ABI violations")
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

bnxt_en: Fix bnxt_hwrm_update_rss_hash_cfg()

We must specify the vnic id of the vnic in the input structure of this
firmware message. Otherwise we will get an error from the firmware.

Fixes: 98a4322b70e8 ("bnxt_en: update RSS config using difference algorithm")
Reviewed-by: Kalesh Anakkur Purayil <kalesh-anakkur.purayil@broadcom.com>
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

eeprom: at24: also select REGMAP

Selecting only REGMAP_I2C can leave REGMAP unset, causing build errors,
so also select REGMAP to prevent the build errors.

../drivers/misc/eeprom/at24.c:540:42: warning: 'struct regmap_config' declared inside parameter list will not be visible outside of this definition or declaration
  540 |                                   struct regmap_config *regmap_config)
../drivers/misc/eeprom/at24.c: In function 'at24_make_dummy_client':
../drivers/misc/eeprom/at24.c:552:18: error: implicit declaration of function 'devm_regmap_init_i2c' [-Werror=implicit-function-declaration]
  552 |         regmap = devm_regmap_init_i2c(dummy_client, regmap_config);
../drivers/misc/eeprom/at24.c:552:16: warning: assignment to 'struct regmap *' from 'int' makes pointer from integer without a cast [-Wint-conversion]
  552 |         regmap = devm_regmap_init_i2c(dummy_client, regmap_config);
../drivers/misc/eeprom/at24.c: In function 'at24_probe':
../drivers/misc/eeprom/at24.c:586:16: error: variable 'regmap_config' has initializer but incomplete type
  586 |         struct regmap_config regmap_config = { };
../drivers/misc/eeprom/at24.c:586:30: error: storage size of 'regmap_config' isn't known
  586 |         struct regmap_config regmap_config = { };
../drivers/misc/eeprom/at24.c:586:30: warning: unused variable 'regmap_config' [-Wunused-variable]

Fixes: 5c015258478e ("eeprom: at24: add basic regmap_i2c support")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>

ceph: fix use-after-free bug for inodes when flushing capsnaps

There is a race between capsnaps flush and removing the inode from
'mdsc->snap_flush_list' list:

   == Thread A ==                     == Thread B ==
ceph_queue_cap_snap()
-> allocate 'capsnapA'
->ihold('&ci->vfs_inode')
->add 'capsnapA' to 'ci->i_cap_snaps'
->add 'ci' to 'mdsc->snap_flush_list'
    ...
   == Thread C ==
ceph_flush_snaps()
->__ceph_flush_snaps()
  ->__send_flush_snap()
                                handle_cap_flushsnap_ack()
                                 ->iput('&ci->vfs_inode')
                                   this also will release 'ci'
                                    ...
      == Thread D ==
                                ceph_handle_snap()
                                 ->flush_snaps()
                                  ->iterate 'mdsc->snap_flush_list'
                                   ->get the stale 'ci'
->remove 'ci' from                ->ihold(&ci->vfs_inode) this
   'mdsc->snap_flush_list'           will WARNING

To fix this we will increase the inode's i_count ref when adding 'ci'
to the 'mdsc->snap_flush_list' list.

[ idryomov: need_put int -> bool ]

Cc: stable@vger.kernel.org
Link: https://bugzilla.redhat.com/show_bug.cgi?id=2209299
Signed-off-by: Xiubo Li <xiubli@redhat.com>
Reviewed-by: Milind Changire <mchangir@redhat.com>
Reviewed-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>

accel/ivpu: Fix sporadic VPU boot failure

Wait for AON bit in HOST_SS_CPR_RST_CLR to return 0 before
starting VPUIP power up sequence, otherwise the VPU device
may sporadically fail to boot.

An error in power up sequence is propagated to the runtime
power management - the device will be in an error state
until the VPU driver is reloaded.

Fixes: 35b137630f08 ("accel/ivpu: Introduce a new DRM driver for Intel VPU")
Cc: stable@vger.kernel.org # 6.3.x
Signed-off-by: Andrzej Kacprowski <andrzej.kacprowski@linux.intel.com>
Reviewed-by: Krystian Pradzynski <krystian.pradzynski@linux.intel.com>
Signed-off-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230607094502.388489-1-stanislaw.gruszka@linux.intel.com

accel/ivpu: Do not use mutex_lock_interruptible

If we get signal when waiting for the mmu->lock we do not invalidate
current MMU configuration that might result in undefined behavior.

Additionally there is little or no benefit on break waiting for
ipc->lock. In current code base, we keep this lock for short periods.

Fixes: 263b2ba5fc93 ("accel/ivpu: Add Intel VPU MMU support")
Reviewed-by: Krystian Pradzynski <krystian.pradzynski@linux.intel.com>
Reviewed-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Signed-off-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230525103818.877590-2-stanislaw.gruszka@linux.intel.com

accel/ivpu: Do not trigger extra VPU reset if the VPU is idle

Turning off the PLL and entering D0i3 will reset the VPU so
an explicit IP reset is redundant.
But if the VPU is active, it may interfere with PLL disabling
and to avoid that, we have to issue an additional IP reset
to silence the VPU before turning off the PLL.

Fixes: a8fed6d1e0b9 ("accel/ivpu: Fix power down sequence")
Cc: stable@vger.kernel.org # 6.3.x
Signed-off-by: Andrzej Kacprowski <andrzej.kacprowski@linux.intel.com>
Reviewed-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Reviewed-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Signed-off-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230525103818.877590-1-stanislaw.gruszka@linux.intel.com

Merge tag 'batadv-net-pullrequest-20230607' of git://git.open-mesh.org/linux-merge

Simon Wunderlich says:

====================
Here is a batman-adv bugfix:

- fix a broken sync while rescheduling delayed work,
by Vladislav Efanov

* tag 'batadv-net-pullrequest-20230607' of git://git.open-mesh.org/linux-merge:
batman-adv: Broken sync while rescheduling delayed work
====================

Link: https://lore.kernel.org/r/20230607155515.548120-1-sw@simonwunderlich.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: bcmgenet: Fix EEE implementation

We had a number of short comings:

- EEE must be re-evaluated whenever the state machine detects a link
  change as wight be switching from a link partner with EEE
  enabled/disabled

- tx_lpi_enabled controls whether EEE should be enabled/disabled for the
  transmit path, which applies to the TBUF block

- We do not need to forcibly enable EEE upon system resume, as the PHY
  state machine will trigger a link event that will do that, too

Fixes: 6ef398ea60d9 ("net: bcmgenet: add EEE support")
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20230606214348.2408018-1-florian.fainelli@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

eth: ixgbe: fix the wake condition

Flip the netif_carrier_ok() condition in queue wake logic.
When I moved it to inside __netif_txq_completed_wake()
I missed negating it.

This made the condition ineffective and could probably
lead to crashes.

Fixes: 301f227fc860 ("net: piggy back on the memory barrier in bql when waking queues")
Reviewed-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20230607010826.960226-2-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

eth: bnxt: fix the wake condition

The down condition should be the negation of the wake condition,
IOW when I moved it from:

if (cond && wake())
to
if (__netif_txq_completed_wake(cond))

Cond should have been negated. Flip it now.

This bug leads to occasional crashes with netconsole.
It may also lead to queue never waking up in case BQL is not enabled.

Reported-by: David Wei <davidhwei@meta.com>
Fixes: 08a096780d92 ("bnxt: use new queue try_stop/try_wake macros")
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/20230607010826.960226-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Merge tag 'for-netdev' of https://git./linux/kernel/git/bpf/bpf

Daniel Borkmann says:

====================
pull-request: bpf 2023-06-07

We've added 7 non-merge commits during the last 7 day(s) which contain
a total of 12 files changed, 112 insertions(+), 7 deletions(-).

The main changes are:

1) Fix a use-after-free in BPF's task local storage, from KP Singh.

2) Make struct path handling more robust in bpf_d_path, from Jiri Olsa.

3) Fix a syzbot NULL-pointer dereference in sockmap, from Eric Dumazet.

4) UAPI fix for BPF_NETFILTER before final kernel ships,
   from Florian Westphal.

5) Fix map-in-map array_map_gen_lookup code generation where elem_size was
   not being set for inner maps, from Rhys Rustad-Elliott.

6) Fix sockopt_sk selftest's NETLINK_LIST_MEMBERSHIPS assertion,
   from Yonghong Song.

* tag 'for-netdev' of https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf:
  bpf: Add extra path pointer check to d_path helper
  selftests/bpf: Fix sockopt_sk selftest
  bpf: netfilter: Add BPF_NETFILTER bpf_attach_type
  selftests/bpf: Add access_inner_map selftest
  bpf: Fix elem_size not being set for inner maps
  bpf: Fix UAF in task local storage
  bpf, sockmap: Avoid potential NULL dereference in sk_psock_verdict_data_ready()
====================

Link: https://lore.kernel.org/r/20230607220514.29698-1-daniel@iogearbox.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

lib: cpu_rmap: Fix potential use-after-free in irq_cpu_rmap_release()

irq_cpu_rmap_release() calls cpu_rmap_put(), which may free the rmap.
So we need to clear the pointer to our glue structure in rmap before
doing that, not after.

Fixes: 4e0473f1060a ("lib: cpu_rmap: Avoid use after free on rmap->obj array entries")
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/ZHo0vwquhOy3FaXc@decadent.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

drm/amd/display: Reduce sdp bw after urgent to 90%

[Description]
Reduce expected SDP bandwidth due to poor QoS and
arbitration issues on high bandwidth configs

Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Acked-by: Stylon Wang <stylon.wang@amd.com>
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Reviewed-by: Nevenko Stupar <Nevenko.Stupar@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: change reserved vram info print

The link object of mgr->reserved_pages is the blocks
variable in struct amdgpu_vram_reservation, not the
link variable in struct drm_buddy_block.

Signed-off-by: YiPeng Chai <YiPeng.Chai@amd.com>
Reviewed-by: Arunpravin Paneer Selvam <Arunpravin.PaneerSelvam@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

drm/amdgpu: fix xclk freq on CHIP_STONEY

According to Alex, most APUs from that time seem to have the same issue
(vbios says 48Mhz, actual is 100Mhz). I only have a CHIP_STONEY so I
limit the fixup to CHIP_STONEY

Signed-off-by: Chia-I Wu <olvaffe@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

drm/radeon: fix race condition UAF in radeon_gem_set_domain_ioctl

Userspace can race to free the gobj(robj converted from), robj should not
be accessed again after drm_gem_object_put, otherwith it will result in
use-after-free.

Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Min Li <lm0963hack@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Revert "drm/amdgpu: switch to golden tsc registers for raven/raven2"

This reverts commit f03eb1d26c2739b75580f58bbab4ab2d5d3eba46.

This results in inconsistent timing reported via asynchronous
GPU queries.

Link: https://lists.freedesktop.org/archives/amd-gfx/2023-May/093731.html
Cc: Jesse.Zhang@amd.com
Cc: michel@daenzer.net
Reviewed-by: Michel Dänzer <mdaenzer@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Revert "drm/amdgpu: Differentiate between Raven2 and Raven/Picasso according to revision id"

This reverts commit 9d2d1827af295fd6971786672c41c4dba3657154.

This results in inconsistent timing reported via asynchronous
GPU queries.

Link: https://lists.freedesktop.org/archives/amd-gfx/2023-May/093731.html
Cc: Jesse.Zhang@amd.com
Cc: michel@daenzer.net
Reviewed-by: Michel Dänzer <mdaenzer@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Revert "drm/amdgpu: change the reference clock for raven/raven2"

This reverts commit fbc24293ca16b3b9ef891fe32ccd04735a6f8dc1.

This results in inconsistent timing reported via asynchronous
GPU queries.

Link: https://lists.freedesktop.org/archives/amd-gfx/2023-May/093731.html
Cc: Jesse.Zhang@amd.com
Cc: michel@daenzer.net
Reviewed-by: Michel Dänzer <mdaenzer@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: add ODM case when looking for first split pipe

[Why]
When going from ODM 2:1 single display case to max displays, second
odm pipe needs to be repurposed for one of the new single displays.
However, acquire_first_split_pipe() only handles MPC case and not
ODM case

[How]
Add ODM conditions in acquire_first_split_pipe()
Add commit_minimal_transition_state() in commit_streams() to handle
odm 2:1 exit first, and then process new streams
Handle ODM condition in commit_minimal_transition_state()

Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Acked-by: Stylon Wang <stylon.wang@amd.com>
Signed-off-by: Samson Tam <samson.tam@amd.com>
Reviewed-by: Alvin Lee <Alvin.Lee2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd: Make lack of `ACPI_FADT_LOW_POWER_S0` or `CONFIG_AMD_PMC` louder during suspend path

Users have reported that s2idle wasn't working on OEM Phoenix systems,
but it was root caused to be because `CONFIG_AMD_PMC` wasn't set in
the distribution kernel config.

To make this more apparent, raise the messaging to err instead of warn.

Link: https://bugzilla.kernel.org/show_bug.cgi?id=217497
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/pm: conditionally disable pcie lane switching for some sienna_cichlid SKUs

Disable the pcie lane switching for some sienna_cichlid SKUs since it
might not work well on some platforms.

Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

drm/amd/pm: Fix power context allocation in SMU13

Use the right data structure for allocation.

Signed-off-by: Lijo Lazar <lijo.lazar@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

drm/amdgpu: fix Null pointer dereference error in amdgpu_device_recover_vram

Use the function of amdgpu_bo_vm_destroy to handle the resource release
of shadow bo. During the amdgpu_mes_self_test, shadow bo released, but
vmbo->shadow_list was not, which caused a null pointer reference error
in amdgpu_device_recover_vram when GPU reset.

Fixes: 6c032c37ac3e ("drm/amdgpu: Fix vram recover doesn't work after whole GPU reset (v2)")
Signed-off-by: xinhui pan <xinhui.pan@amd.com>
Signed-off-by: Horatio Zhang <Hongkun.Zhang@amd.com>
Acked-by: Feifei Xu <Feifei.Xu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd: Disallow s0ix without BIOS support again

commit cf488dcd0ab7 ("drm/amd: Allow s0ix without BIOS support") showed
improvements to power consumption over suspend when s0ix wasn't enabled in
BIOS and the system didn't support S3.

This patch however was misguided because the reason the system didn't
support S3 was because SMT was disabled in OEM BIOS setup.
This prevented the BIOS from allowing S3.

Also allowing GPUs to use the s2idle path actually causes problems if
they're invoked on systems that may not support s2idle in the platform
firmware. `systemd` has a tendency to try to use `s2idle` if `deep` fails
for any reason, which could lead to unexpected flows.

The original commit also fixed a problem during resume from suspend to idle
without hardware support, but this is no longer necessary with commit
ca4751866397 ("drm/amd: Don't allow s0ix on APUs older than Raven")

Revert commit cf488dcd0ab7 ("drm/amd: Allow s0ix without BIOS support")
to make it match the expected behavior again.

Cc: Rafael Ávila de Espíndola <rafael@espindo.la>
Link: https://github.com/torvalds/linux/blob/v6.1/drivers/gpu/drm/amd/amdgpu/amdgpu_acpi.c#L1060
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/2599
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

Merge tag 'input-for-v6.4-rc5' of git://git./linux/kernel/git/dtor/input

Pull input fixes from Dmitry Torokhov:

- a fix for unbalanced open count for inhibited input devices

- fixups in Elantech PS/2 and Cyppress TTSP v5 drivers

- a quirk to soc_button_array driver to make it work with Lenovo
   Yoga Book X90F / X90L

- a removal of erroneous entry from xpad driver

* tag 'input-for-v6.4-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: xpad - delete a Razer DeathAdder mouse VID/PID entry
  Input: psmouse - fix OOB access in Elantech protocol
  Input: soc_button_array - add invalid acpi_index DMI quirk handling
  Input: fix open count when closing inhibited device
  Input: cyttsp5 - fix array length

vhost: use kzalloc() instead of kmalloc() followed by memset()

Use kzalloc() to allocate new zeroed out msg node instead of
memsetting a node allocated with kmalloc().

Signed-off-by: Prathu Baronia <prathubaronia2011@gmail.com>
Message-Id: <20230522085019.42914-1-prathubaronia2011@gmail.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>

MAINTAINERS: Add entry for debug objects

This is overdue and an oversight.

Add myself to this file deespite the fact that I'm trying to reduce the
number of entries in this file which have my name attached, but in the
hope that patches wont get picked up elsewhere completely unreviewed and
unnoticed.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

afs: Fix setting of mtime when creating a file/dir/symlink

kafs incorrectly passes a zero mtime (ie. 1st Jan 1970) to the server when
creating a file, dir or symlink because the mtime recorded in the
afs_operation struct gets passed to the server by the marshalling routines,
but the afs_mkdir(), afs_create() and afs_symlink() functions don't set it.

This gets masked if a file or directory is subsequently modified.

Fix this by filling in op->mtime before calling the create op.

Fixes: e49c7b2f6de7 ("afs: Build an abstraction around an "operation" concept")
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Jeffrey Altman <jaltman@auristor.com>
Reviewed-by: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
cc: linux-fsdevel@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

riscv: Check the virtual alignment before choosing a map size

We used to only check the alignment of the physical address to decide
which mapping would fit for a certain region of the linear mapping, but
it is not enough since the virtual address must also be aligned, so check
that too.

Fixes: 3335068f8721 ("riscv: Use PUD/P4D/PGD pages for the linear mapping")
Reported-by: Song Shuai <songshuaishuai@tinylab.org>
Link: https://lore.kernel.org/linux-riscv/tencent_7C3B580B47C1B17C16488EC1@qq.com/
Signed-off-by: Alexandre Ghiti <alexghiti@rivosinc.com>
Link: https://lore.kernel.org/r/20230607125851.63370-1-alexghiti@rivosinc.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>

riscv: Fix kfence now that the linear mapping can be backed by PUD/P4D/PGD

RISC-V Kfence implementation used to rely on the fact the linear mapping
was backed by at most PMD hugepages, which is not true anymore since
commit 3335068f8721 ("riscv: Use PUD/P4D/PGD pages for the linear
mapping").

Instead of splitting PUD/P4D/PGD mappings afterwards, directly map the
kfence pool region using PTE mappings by allocating this region before
setup_vm_final().

Reported-by: syzbot+a74d57bddabbedd75135@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=a74d57bddabbedd75135
Fixes: 3335068f8721 ("riscv: Use PUD/P4D/PGD pages for the linear mapping")
Signed-off-by: Alexandre Ghiti <alexghiti@rivosinc.com>
Link: https://lore.kernel.org/r/20230606130444.25090-1-alexghiti@rivosinc.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>

riscv: mm: Ensure prot of VM_WRITE and VM_EXEC must be readable

Commit 8aeb7b17f04e ("RISC-V: Make mmap() with PROT_WRITE imply PROT_READ")
allows riscv to use mmap with PROT_WRITE only, and meanwhile mmap with w+x
is also permitted. However, when userspace tries to access this page with
PROT_WRITE|PROT_EXEC, which causes infinite loop at load page fault as
well as it triggers soft lockup. According to riscv privileged spec,
"Writable pages must also be marked readable". The fix to drop the
`PAGE_COPY_READ_EXEC` and then `PAGE_COPY_EXEC` would be just used instead.
This aligns the other arches (i.e arm64) for protection_map.

Fixes: 8aeb7b17f04e ("RISC-V: Make mmap() with PROT_WRITE imply PROT_READ")
Signed-off-by: Hsieh-Tseng Shen <woodrow.shen@sifive.com>
Reviewed-by: Alexandre Ghiti <alexghiti@rivosinc.com>
Link: https://lore.kernel.org/r/20230425102828.1616812-1-woodrow.shen@sifive.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>

bpf: Add extra path pointer check to d_path helper

Anastasios reported crash on stable 5.15 kernel with following
BPF attached to lsm hook:

  SEC("lsm.s/bprm_creds_for_exec")
  int BPF_PROG(bprm_creds_for_exec, struct linux_binprm *bprm)
  {
          struct path *path = &bprm->executable->f_path;
          char p[128] = { 0 };

          bpf_d_path(path, p, 128);
          return 0;
  }

But bprm->executable can be NULL, so bpf_d_path call will crash:

  BUG: kernel NULL pointer dereference, address: 0000000000000018
  #PF: supervisor read access in kernel mode
  #PF: error_code(0x0000) - not-present page
  PGD 0 P4D 0
  Oops: 0000 [#1] PREEMPT SMP DEBUG_PAGEALLOC NOPTI
  ...
  RIP: 0010:d_path+0x22/0x280
  ...
  Call Trace:
   <TASK>
   bpf_d_path+0x21/0x60
   bpf_prog_db9cf176e84498d9_bprm_creds_for_exec+0x94/0x99
   bpf_trampoline_6442506293_0+0x55/0x1000
   bpf_lsm_bprm_creds_for_exec+0x5/0x10
   security_bprm_creds_for_exec+0x29/0x40
   bprm_execve+0x1c1/0x900
   do_execveat_common.isra.0+0x1af/0x260
   __x64_sys_execve+0x32/0x40

It's problem for all stable trees with bpf_d_path helper, which was
added in 5.9.

This issue is fixed in current bpf code, where we identify and mark
trusted pointers, so the above code would fail even to load.

For the sake of the stable trees and to workaround potentially broken
verifier in the future, adding the code that reads the path object from
the passed pointer and verifies it's valid in kernel space.

Fixes: 6e22ab9da793 ("bpf: Add d_path helper")
Reported-by: Anastasios Papagiannis <tasos.papagiannnis@gmail.com>
Suggested-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Stanislav Fomichev <sdf@google.com>
Acked-by: Yonghong Song <yhs@fb.com>
Link: https://lore.kernel.org/bpf/20230606181714.532998-1-jolsa@kernel.org

MAINTAINERS: add Andy Shevchenko as reviewer for the GPIO subsystem

Andy has been a de-facto reviewer for all things GPIO for a long time so
let's make it official.

Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Acked-by: Andy Shevchenko <andy@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>

gpio: sim: quietly ignore configured lines outside the bank

The user-space policy of the gpio-sim is that configuration for lines
with offsets outside the bounds of the corresponding bank is ignored,
but gpio-sim is still using that configuration when constructing the
sim. In the case of named lines this results in temporarily allocating
space for names that are not used, and for hogs results in errors being
logged when the gpio-sim attempts to register the out of range hog with
gpiolib:

gpiochip_machine_hog: unable to get GPIO desc: -22

Add checks to filter out any line configuration outside the bounds
of the bank when constructing the sim.

Signed-off-by: Kent Gibson <warthog618@gmail.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>

net: sched: fix possible refcount leak in tc_chain_tmplt_add()

try_module_get will be called in tcf_proto_lookup_ops. So module_put needs
to be called to drop the refcount if ops don't implement the required
function.

Fixes: 9f407f1768d3 ("net: sched: introduce chain templates")
Signed-off-by: Hangyu Hua <hbh25y@gmail.com>
Reviewed-by: Larysa Zaremba <larysa.zaremba@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: sched: act_police: fix sparse errors in tcf_police_dump()

Fixes following sparse errors:

net/sched/act_police.c:360:28: warning: dereference of noderef expression
net/sched/act_police.c:362:45: warning: dereference of noderef expression
net/sched/act_police.c:362:45: warning: dereference of noderef expression
net/sched/act_police.c:368:28: warning: dereference of noderef expression
net/sched/act_police.c:370:45: warning: dereference of noderef expression
net/sched/act_police.c:370:45: warning: dereference of noderef expression
net/sched/act_police.c:376:45: warning: dereference of noderef expression
net/sched/act_police.c:376:45: warning: dereference of noderef expression

Fixes: d1967e495a8d ("net_sched: act_police: add 2 new attributes to support police 64bit rate and peakrate")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: openvswitch: fix upcall counter access before allocation

Currently, the per cpu upcall counters are allocated after the vport is
created and inserted into the system. This could lead to the datapath
accessing the counters before they are allocated resulting in a kernel
Oops.

Here is an example:

  PID: 59693    TASK: ffff0005f4f51500  CPU: 0    COMMAND: "ovs-vswitchd"
   #0 [ffff80000a39b5b0] __switch_to at ffffb70f0629f2f4
   #1 [ffff80000a39b5d0] __schedule at ffffb70f0629f5cc
   #2 [ffff80000a39b650] preempt_schedule_common at ffffb70f0629fa60
   #3 [ffff80000a39b670] dynamic_might_resched at ffffb70f0629fb58
   #4 [ffff80000a39b680] mutex_lock_killable at ffffb70f062a1388
   #5 [ffff80000a39b6a0] pcpu_alloc at ffffb70f0594460c
   #6 [ffff80000a39b750] __alloc_percpu_gfp at ffffb70f05944e68
   #7 [ffff80000a39b760] ovs_vport_cmd_new at ffffb70ee6961b90 [openvswitch]
   ...

  PID: 58682    TASK: ffff0005b2f0bf00  CPU: 0    COMMAND: "kworker/0:3"
   #0 [ffff80000a5d2f40] machine_kexec at ffffb70f056a0758
   #1 [ffff80000a5d2f70] __crash_kexec at ffffb70f057e2994
   #2 [ffff80000a5d3100] crash_kexec at ffffb70f057e2ad8
   #3 [ffff80000a5d3120] die at ffffb70f0628234c
   #4 [ffff80000a5d31e0] die_kernel_fault at ffffb70f062828a8
   #5 [ffff80000a5d3210] __do_kernel_fault at ffffb70f056a31f4
   #6 [ffff80000a5d3240] do_bad_area at ffffb70f056a32a4
   #7 [ffff80000a5d3260] do_translation_fault at ffffb70f062a9710
   #8 [ffff80000a5d3270] do_mem_abort at ffffb70f056a2f74
   #9 [ffff80000a5d32a0] el1_abort at ffffb70f06297dac
  #10 [ffff80000a5d32d0] el1h_64_sync_handler at ffffb70f06299b24
  #11 [ffff80000a5d3410] el1h_64_sync at ffffb70f056812dc
  #12 [ffff80000a5d3430] ovs_dp_upcall at ffffb70ee6963c84 [openvswitch]
  #13 [ffff80000a5d3470] ovs_dp_process_packet at ffffb70ee6963fdc [openvswitch]
  #14 [ffff80000a5d34f0] ovs_vport_receive at ffffb70ee6972c78 [openvswitch]
  #15 [ffff80000a5d36f0] netdev_port_receive at ffffb70ee6973948 [openvswitch]
  #16 [ffff80000a5d3720] netdev_frame_hook at ffffb70ee6973a28 [openvswitch]
  #17 [ffff80000a5d3730] __netif_receive_skb_core.constprop.0 at ffffb70f06079f90

We moved the per cpu upcall counter allocation to the existing vport
alloc and free functions to solve this.

Fixes: 95637d91fefd ("net: openvswitch: release vport resources on failure")
Fixes: 1933ea365aa7 ("net: openvswitch: Add support to count upcall packets")
Signed-off-by: Eelco Chaudron <echaudro@redhat.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Acked-by: Aaron Conole <aconole@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: sched: move rtm_tca_policy declaration to include file

rtm_tca_policy is used from net/sched/sch_api.c and net/sched/cls_api.c,
thus should be declared in an include file.

This fixes the following sparse warning:
net/sched/sch_api.c:1434:25: warning: symbol 'rtm_tca_policy' was not declared. Should it be static?

Fixes: e331473fee3d ("net/sched: cls_api: add missing validation of netlink attributes")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'amdtee-fix-for-v6.5' of https://git.linaro.org/people/jens.wiklander/linux-tee into arm/fixes

AMDTEE add return origin to load TA command

* tag 'amdtee-fix-for-v6.5' of https://git.linaro.org/people/jens.wiklander/linux-tee:
tee: amdtee: Add return_origin to 'struct tee_cmd_load_ta'

Link: https://lore.kernel.org/r/20230606075843.GA2792442@rayden
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

i2c: sprd: Delete i2c adapter in .remove's error path

If pm runtime resume fails the .remove callback used to exit early. This
resulted in an error message by the driver core but the device gets
removed anyhow. This lets the registered i2c adapter stay around with an
unbound parent device.

So only skip clk disabling if resume failed, but do delete the adapter.

Fixes: 8b9ec0719834 ("i2c: Add Spreadtrum I2C controller driver")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

ice: make writes to /dev/gnssX synchronous

The current ice driver's GNSS write implementation buffers writes and
works through them asynchronously in a kthread. That's bad because:
- The GNSS write_raw operation is supposed to be synchronous[1][2].
- There is no upper bound on the number of pending writes.
   Userspace can submit writes much faster than the driver can process,
   consuming unlimited amounts of kernel memory.

A patch that's currently on review[3] ("[v3,net] ice: Write all GNSS
buffers instead of first one") would add one more problem:
- The possibility of waiting for a very long time to flush the write
   work when doing rmmod, softlockups.

To fix these issues, simplify the implementation: Drop the buffering,
the write_work, and make the writes synchronous.

I tested this with gpsd and ubxtool.

[1] https://events19.linuxfoundation.org/wp-content/uploads/2017/12/The-GNSS-Subsystem-Johan-Hovold-Hovold-Consulting-AB.pdf
    "User interface" slide.
[2] A comment in drivers/gnss/core.c:gnss_write():
        /* Ignoring O_NONBLOCK, write_raw() is synchronous. */
[3] https://patchwork.ozlabs.org/project/intel-wired-lan/patch/20230217120541.16745-1-karol.kolacinski@intel.com/

Fixes: d6b98c8d242a ("ice: add write functionality for GNSS TTY")
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Tested-by: Sunitha Mekala <sunithax.d.mekala@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

drm/i915/selftests: Add some missing error propagation

Add some missing error propagation in live_parallel_switch.

To avoid needlessly burdening the various backport processes, note I am
not marking it as a fix against any patches and not copying stable since
it is debug/selftests only code.

Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Cc: Andi Shyti <andi.shyti@linux.intel.com>
Reviewed-by: Andi Shyti <andi.shyti@linux.intel.com>
Fixes: 50d16d44cce4 ("drm/i915/selftests: Exercise context switching in parallel")
Fixes: 6407cf533217 ("drm/i915/selftests: Stop using kthread_stop()")
Link: https://patchwork.freedesktop.org/patch/msgid/20230605131135.396854-1-tvrtko.ursulin@linux.intel.com
(cherry picked from commit 412fa1f097f48c8c1321806dd25e46618e0da147)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>

net: sched: add rcu annotations around qdisc->qdisc_sleeping

syzbot reported a race around qdisc->qdisc_sleeping [1]

It is time we add proper annotations to reads and writes to/from
qdisc->qdisc_sleeping.

[1]
BUG: KCSAN: data-race in dev_graft_qdisc / qdisc_lookup_rcu

read to 0xffff8881286fc618 of 8 bytes by task 6928 on cpu 1:
qdisc_lookup_rcu+0x192/0x2c0 net/sched/sch_api.c:331
__tcf_qdisc_find+0x74/0x3c0 net/sched/cls_api.c:1174
tc_get_tfilter+0x18f/0x990 net/sched/cls_api.c:2547
rtnetlink_rcv_msg+0x7af/0x8c0 net/core/rtnetlink.c:6386
netlink_rcv_skb+0x126/0x220 net/netlink/af_netlink.c:2546
rtnetlink_rcv+0x1c/0x20 net/core/rtnetlink.c:6413
netlink_unicast_kernel net/netlink/af_netlink.c:1339 [inline]
netlink_unicast+0x56f/0x640 net/netlink/af_netlink.c:1365
netlink_sendmsg+0x665/0x770 net/netlink/af_netlink.c:1913
sock_sendmsg_nosec net/socket.c:724 [inline]
sock_sendmsg net/socket.c:747 [inline]
____sys_sendmsg+0x375/0x4c0 net/socket.c:2503
___sys_sendmsg net/socket.c:2557 [inline]
__sys_sendmsg+0x1e3/0x270 net/socket.c:2586
__do_sys_sendmsg net/socket.c:2595 [inline]
__se_sys_sendmsg net/socket.c:2593 [inline]
__x64_sys_sendmsg+0x46/0x50 net/socket.c:2593
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x41/0xc0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x63/0xcd

write to 0xffff8881286fc618 of 8 bytes by task 6912 on cpu 0:
dev_graft_qdisc+0x4f/0x80 net/sched/sch_generic.c:1115
qdisc_graft+0x7d0/0xb60 net/sched/sch_api.c:1103
tc_modify_qdisc+0x712/0xf10 net/sched/sch_api.c:1693
rtnetlink_rcv_msg+0x807/0x8c0 net/core/rtnetlink.c:6395
netlink_rcv_skb+0x126/0x220 net/netlink/af_netlink.c:2546
rtnetlink_rcv+0x1c/0x20 net/core/rtnetlink.c:6413
netlink_unicast_kernel net/netlink/af_netlink.c:1339 [inline]
netlink_unicast+0x56f/0x640 net/netlink/af_netlink.c:1365
netlink_sendmsg+0x665/0x770 net/netlink/af_netlink.c:1913
sock_sendmsg_nosec net/socket.c:724 [inline]
sock_sendmsg net/socket.c:747 [inline]
____sys_sendmsg+0x375/0x4c0 net/socket.c:2503
___sys_sendmsg net/socket.c:2557 [inline]
__sys_sendmsg+0x1e3/0x270 net/socket.c:2586
__do_sys_sendmsg net/socket.c:2595 [inline]
__se_sys_sendmsg net/socket.c:2593 [inline]
__x64_sys_sendmsg+0x46/0x50 net/socket.c:2593
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x41/0xc0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x63/0xcd

Reported by Kernel Concurrency Sanitizer on:
CPU: 0 PID: 6912 Comm: syz-executor.5 Not tainted 6.4.0-rc3-syzkaller-00190-g0d85b27b0cc6 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 05/16/2023

Fixes: 3a7d0d07a386 ("net: sched: extend Qdisc with rcu")
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Vlad Buslov <vladbu@nvidia.com>
Acked-by: Jamal Hadi Salim<jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'rfs-lockless-annotate'

Eric Dumazet says:

====================
rfs: annotate lockless accesses

rfs runs without locks held, so we should annotate
read and writes to shared variables.

It should prevent compilers forcing writes
in the following situation:

  if (var != val)
     var = val;

A compiler could indeed simply avoid the conditional:

    var = val;

This matters if var is shared between many cpus.

v2: aligns one closing bracket (Simon)
    adds Fixes: tags (Jakub)
====================

Signed-off-by: David S. Miller <davem@davemloft.net>