Zongdong Jiao [Thu, 30 May 2019 12:08:41 +0000 (20:08 +0800)]
hdmitx: edid: add suitable case for DolbyVision [1/1]
PD#SWPL-7888
Problem:
DV tests add more EDID cases
v2_yuv444_2_yuv422_0_int_3_12Byte.xml
v2_yuv444_0_yuv422_0_int_2_13Byte.xml
v2_yuv444_0_yuv422_0_int_2_16Byte.xml
Solution:
add suitable case for DolbyVision
Verify:
G12/U212
Change-Id: I323d49ad34b12b6a12ba93f0349f0398f2516bcb
Signed-off-by: Zongdong Jiao <zongdong.jiao@amlogic.com>
he.he [Thu, 30 May 2019 06:54:52 +0000 (14:54 +0800)]
usb: panel type-c need support adb and u-disk [1/1]
PD#SWPL-9127
Problem:
the id pin of the type-c is aways high, whether it is connected to u disk
or usb cable.
Solution:
It need set vbus high when the usb mode is host only.
Verify:
test passed on sm1
Change-Id: I4ff8a9b5419b54828ecd797a78d149da98535dee
Signed-off-by: he.he <he.he@amlogic.com>
Shuai Li [Tue, 4 Jun 2019 05:41:43 +0000 (13:41 +0800)]
audio: audio ABUS stuck issue [1/1]
PD#SWPL-9142
Problem:
Audio Abus may be stuck if it is stopped
when the burst is not finished.
And the stuck can't be recovered
unless reboot the system.
Solution:
Add check to make sure that the transfer
is over then start to disable the toddr fifo.
Verify:
TL1 stress test.
Change-Id: I28dcf84ddec421bc70370b2544f0bf1f3272e7b4
Signed-off-by: Shuai Li <shuai.li@amlogic.com>
Jiacheng Mei [Tue, 4 Jun 2019 09:33:02 +0000 (17:33 +0800)]
dts: reduce isp reserved mem [1/1]
PD#SWPL-70
Problem:
arm isp can't get reserved mem
Solution:
reduce isp reserved mem
Verify:
w400
Test: camera preview and capture OK
Change-Id: Icaf630a25a55d31ec3ed68cae48fb840017c9fc0
Signed-off-by: Jiacheng Mei <jiacheng.mei@amlogic.com>
Xiaoming Sui [Thu, 30 May 2019 11:25:35 +0000 (19:25 +0800)]
avsync: tsync: fix avsync issue when streams replayed [2/2]
PD#TV-6448
Problem:
when streams replayed, the video is blocked about 6s sometimes.
Solution:
when streams replayed, if pcr clock enable, then recalculate the
pcr clock for system clock from the stream to sync the video and audio.
Verify:
X301
Change-Id: Ic414fdc102753e1e1dcedfef2a5cb76ddddf6383
Signed-off-by: Xiaoming Sui <xiaoming.sui@amlogic.com>
Luan Yuan [Thu, 30 May 2019 06:22:18 +0000 (14:22 +0800)]
dts: change codec mm size to 192M. [1/1]
PD#SWPL-9156
Problem:
memory overread error
Solution:
fixed play movie error
Verify:
verify by ac202/u202
Change-Id: I15e459a4fe044b02a5e958293c1516f8b7795096
Signed-off-by: Luan Yuan <luan.yuan@amlogic.com>
Evoke Zhang [Fri, 24 May 2019 07:40:34 +0000 (15:40 +0800)]
tvafe: change force_nostd adjust to sysfs node [1/1]
PD#TV-5482
Problem:
Image flicker for non-std avin,
because the force_nostd parameter is modified to a unsuitable value.
Solution:
remove force_nostd paramete,
add sysfs node support for force_nostd
Verify:
x301
Change-Id: Ic50a311c6b5a63bcbd1d56651713de5be60a38a2
Signed-off-by: Evoke Zhang <evoke.zhang@amlogic.com>
Ruixuan Li [Tue, 21 May 2019 11:32:48 +0000 (19:32 +0800)]
emmc: modify the emmc device driver strength to type 0 [1/1]
PD#SWPL-8806
Problem:
the driver strength is type 1 on sm1
Solution:
modify sm1 dts
Verify:
passed on sm1_ac213
Change-Id: Iea5093541dc0bbd08954e78827309a45a84efc60
Signed-off-by: Ruixuan Li <ruixuan.li@amlogic.com>
Zhe Wang [Wed, 22 May 2019 10:40:17 +0000 (18:40 +0800)]
audio: enable clk before extern codec init when system resume [1/1]
PD#TV-6005
Problem:
change time sequence for extern AMP
Solution:
1) enable tdm clk before codec init, when system resume
Verify:
test on X301
Change-Id: I3d6411cd32fbc3496bed942c72b7bec408d66959
Signed-off-by: Zhe Wang <Zhe.Wang@amlogic.com>
Laura Abbott [Mon, 3 Apr 2017 18:57:48 +0000 (11:57 -0700)]
staging: android: ion: Call dma_map_sg for syncing and mapping [2/2]
PD#SWPL-9254
Problem:
uncached display unexpectly.
Solution:
Technically, calling dma_buf_map_attachment should return a buffer
properly dma_mapped. Add calls to dma_map_sg to begin_cpu_access to
ensure this happens. As a side effect, this lets Ion buffers take
advantage of the dma_buf sync ioctls.
Verify:
galilei, franklin
Change-Id: Ib6ca06e59e81031d3c65c2df8824b46baaba6c9f
Signed-off-by: Laura Abbott <labbott@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Jiyu Yang <Jiyu.Yang@amlogic.com>
Laura Abbott [Mon, 3 Apr 2017 18:57:47 +0000 (11:57 -0700)]
staging: android: ion: Duplicate sg_table [1/2]
PD#SWPL-9254
Problem:
Ion currently returns a single sg_table on each dma_map call. This is
incorrect for later usage.
Solution:
dup sg table on each dma_map call
Verify:
galilei, franklin
Change-Id: I6df2baa33bba9303b2ac25210ebaf56a337d56a2
Signed-off-by: Laura Abbott <labbott@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Jiyu Yang <Jiyu.Yang@amlogic.com>
Brian Zhu [Wed, 29 May 2019 09:44:03 +0000 (17:44 +0800)]
vpp: create a variable for cm input size [1/2]
PD#TV-5968
Problem:
Too many case for cm input size with differnet chips.
SR0+SR1+PPS.
Solution:
Add a variable to indicate the cm input size.
Verify:
on r311
Change-Id: I5f1024340c67edbdf646c1b5bb7cad95b93b7b92
Signed-off-by: Brian Zhu <brian.zhu@amlogic.com>
jintao xu [Fri, 31 May 2019 06:33:13 +0000 (14:33 +0800)]
pipvideo: fix cur_pipbuf not set to NULL when disable video before unreg [1/1]
PD#OTT-4262
Problem:
When disable video before unreg, cur_pipbuf will not set to NULL.
Next time playback will tog this buffer.
Solution:
Free cur_pipbuf when vd2 is closed in unreg.
Verify:
U212
Change-Id: Ie381ae9feda8a5d23a93b3a5974d9c0af87e6d6e
Signed-off-by: jintao xu <jintao.xu@amlogic.com>
zhiwei.yuan [Fri, 31 May 2019 11:30:31 +0000 (19:30 +0800)]
dtv_demod: mosaic is seen when cable pulg/unplug several times [1/1]
PD#SWPL-8182
Problem:
signal has problem after fec lock during cable plug-in
Solution:
delay fec lock
Verify:
verified by t962x2_x301
Change-Id: I7ec8c8651ecb25cc91673829bd17d4d70dd8b6a3
Signed-off-by: zhiwei.yuan <zhiwei.yuan@amlogic.com>
Zhe Wang [Mon, 3 Jun 2019 09:33:07 +0000 (17:33 +0800)]
audio: set resample clk to mclk of tdm [1/2]
PD#TV-5865
Problem:
hdmiin frequency responds test fail.
Solution:
set resample clk to mclk of tdm
Verify:
X301
Change-Id: I22c92219bcea534bdec2bc526d535cacd971faa5
Signed-off-by: Zhe Wang <Zhe.Wang@amlogic.com>
Shunzhou Jiang [Tue, 14 May 2019 01:47:43 +0000 (09:47 +0800)]
clk: sm1: add sm1 dsu clk notify for change dsu freq [1/1]
PD#SWPL-8145
Problem:
dsu clk can't change freq
Solution:
add sm1 dsu clk notify
Verify:
sm1_skt
Change-Id: If3ecf1066b49c07e6af69ce342956cb0469a5f87
Signed-off-by: Shunzhou Jiang <shunzhou.jiang@amlogic.com>
Signed-off-by: Hong Guo <hong.guo@amlogic.com>
Evoke Zhang [Thu, 30 May 2019 08:45:03 +0000 (16:45 +0800)]
tvafe: optimize display for line frequency scan range [1/1]
PD#TV-5770
Problem:
atv line freq offset -220hz display abnormal
Solution:
optimize acd_64/66 reg setting
Verify:
x301
Change-Id: I41fec1513a735ea6cd5975b18f01e8f80afe4f51
Signed-off-by: Evoke Zhang <evoke.zhang@amlogic.com>
Lifeng Cao [Wed, 29 May 2019 08:03:04 +0000 (16:03 +0800)]
video: Some interlace stream will stuck when pts rebound [1/1]
PD#TV-6236
Problem:
Some interlace stream di has buffer count more than 16
If video pts rebound in this stream. The condition that
(abs(omx_pts_set_index - next_vf->omx_index) <= 16) is
not true. So this frame can not toggle always.
Solution:
Delete this condition that
(abs(omx_pts_set_index - next_vf->omx_index) <= 16)
Verify:
verify TL1
Change-Id: I7e8c12ec72d086b0516f7c7490b492e16e36e8fe
Signed-off-by: Lifeng Cao <lifeng.cao@amlogic.com>
Evoke Zhang [Thu, 23 May 2019 06:37:40 +0000 (14:37 +0800)]
tvafe: vbi: optimize search_table performance [1/1]
PD#TV-4910
Problem:
vbi search_table for invalid data will cost more cpu resource
Solution:
optimze search_table performance to save cpu resource
Verify:
x301
Change-Id: If92aa4e6d58894c6b78833cd367eacd8e9a76d5b
Signed-off-by: Evoke Zhang <evoke.zhang@amlogic.com>
shuanglong.wang [Mon, 3 Jun 2019 01:56:30 +0000 (09:56 +0800)]
video: clear pcr in video stop [1/1]
PD#SWPL-6903
Problem:
pcr increase automatic after system reset
Solution:
in non-tunnel mode, only after video stop post will adjust pcr
in omx_secret_mode. Also clear pcr in video stop
Verify:
verify by nts
Change-Id: I528229e8121a99e50c7b8313bd8dc867e3710ad8
Signed-off-by: shuanglong.wang <shuanglong.wang@amlogic.com>
Nanxin Qin [Sun, 26 May 2019 16:22:30 +0000 (00:22 +0800)]
media: add interface for checks the video profile. [1/2]
PD#SWPL-8648
Problem:
add interface for checks the video profile
Solution:
add interface for checks the video profile
Verify:
u212
Change-Id: I95d0df62fae2debc6c0cc5a4d2adf002122b7630
Signed-off-by: Nanxin Qin <nanxin.qin@amlogic.com>
Hanjie Lin [Mon, 29 Apr 2019 07:49:01 +0000 (15:49 +0800)]
ftrace: enable preempt and irqsoff tracer default [1/1]
PD#SWPL-7807
Problem:
preempt and irqsoff tracer is disabled by default
Solution:
enable preempt and irqsoff tracer default for debug
Verify:
sm1
Change-Id: I825f1d1cfb53209a0bd5b361a58a04cd1c90cb96
Signed-off-by: Hanjie Lin <hanjie.lin@amlogic.com>
Hanjie Lin [Mon, 20 May 2019 11:50:39 +0000 (19:50 +0800)]
sched: disable EAS on non-big-little platforms [1/1]
PD#SWPL-8759
Problem:
disable EAS on non-big-little platforms
Solution:
disable EAS on non-big-little platforms
Verify:
w400, u200
Change-Id: I11845def9efaa2e1da8fd30ac26daeb0dc47eda4
Signed-off-by: Hanjie Lin <hanjie.lin@amlogic.com>
nengwen.chen [Mon, 27 May 2019 08:34:23 +0000 (16:34 +0800)]
atv_demod: fix a2/nicam/mono sound output power [1/1]
PD#TV-6140
Problem:
fix a2/nicam/mono sound output power.
Solution:
1.fix a2/nicam/mono sound output power.
Verify:
Verified by x301
Change-Id: I0dc192cd841d2b1c4d25d2d6c5569a69575ce735
Signed-off-by: nengwen.chen <nengwen.chen@amlogic.com>
Hang Cheng [Thu, 16 May 2019 02:20:08 +0000 (10:20 +0800)]
hdmirx: add edid data splice function [1/1]
PD#SWPL-8467
Problem:
1.no index parse for edid data block
2.no earc capabilities data structure parse
3.no earc cap data structure splice function
4.no cta data block splice/remove function
Solution:
1.add edid data block index parse
2.add earc capabilities data structure parse
3.add splice function of earc cap data structure
4.add splice/remove function of data block to edid
Verify:
TL1
Change-Id: I47b9f2176c31c65a08cdc657c00398f88cbdd7d3
Signed-off-by: Hang Cheng <hang.cheng@amlogic.com>
Gongwei Chen [Fri, 31 May 2019 06:59:10 +0000 (14:59 +0800)]
audio: Speaker has no sound [1/1]
PD#IPTV-3107
Problem:
Speaker has no sound
Solution:
modify dts and
ad82584f
Verify:
Verify by Android P S905D3 AC202
Change-Id: I92ddb6a86b31dcd2c37311a0fc9b1a2cefc29d4e
Signed-off-by: GongWei Chen <gongwei.chen@amlogic.com>
Xingyu Chen [Mon, 27 May 2019 05:18:31 +0000 (13:18 +0800)]
arm64: dts: remove the adc_keypad node for ac213 board [1/1]
PD#SWPL-8711
Problem:
the adckey driver maybe reports unexpected event when the configured
channel is dangling.
Solution:
the board does not support adckey, remove the adc_keypad node in dts
Verify:
test pass on ac213
Change-Id: I78eeb608928c1d455f6c659127e75f3d77d09541
Signed-off-by: Xingyu Chen <xingyu.chen@amlogic.com>
Yong Qin [Fri, 31 May 2019 02:29:33 +0000 (10:29 +0800)]
vdin: Flash blurre screen when change hdmi 4k timing [1/1]
PD#SWPL-8153
Problem:
Flash blurre screen when change all 4K format
Solution:
if no video buffer resouce, needn't set afbce regiter
when need switch afbc mode.
Verify:
tl1
Change-Id: Ifb867cdeda2b6d3536246b79531a5bf9027e01a1
Signed-off-by: Yong Qin <yong.qin@amlogic.com>
Hang Cheng [Thu, 30 May 2019 07:00:23 +0000 (15:00 +0800)]
hdmitx: force to set rxsense state low if hpd is low [1/1]
PD#OTT-3663
Problem:
when hpd low, hdmitx phy is disabled, the rxsense
state is not right
Solution:
force to set rxsense state = 0 when hpd is low
Verify:
p212
Change-Id: I8fa3e8a647558f0cbfc62e9384613911efbef559
Signed-off-by: Hang Cheng <hang.cheng@amlogic.com>
Jian Xu [Wed, 29 May 2019 12:06:35 +0000 (20:06 +0800)]
audio: auge: fix the samesource spdif clock recovery issue [1/1]
PD#SWPL-3667
Problem:
after playback none-48K raw audio, the spdif clock
is not recoved to 48K when tdm/spdif same source
Solution:
use the same clock source as tdm if samesource and
config that when tdm hardware prepare.
Verify:
AC213
Change-Id: I0d5dc5f51b5de14d155902e0fe72c293071c93ec
Signed-off-by: Jian Xu <jian.xu@amlogic.com>
nengwen.chen [Tue, 21 May 2019 08:12:40 +0000 (16:12 +0800)]
atv_demod: fix nicam audio [1/1]
PD#TV-5660
Problem:
fix nicam audio.
Solution:
1.fix nicam audio.
Verify:
Verified by x301
Change-Id: I35d508d1772b9c37ad71a62c2844e1776e81fd09
Signed-off-by: nengwen.chen <nengwen.chen@amlogic.com>
Wenfeng Guo [Wed, 29 May 2019 07:48:52 +0000 (15:48 +0800)]
di: fix image jitter and flash av ntsc [1/1]
PD#SWPL-8937
Problem:
image jitter and flash av ntsc
Solution:
1.force entry pulldown32
Verify:
tl1
Change-Id: I8e86993be8db358c70cd9a4d86c9d578bce74f6e
Signed-off-by: Wenfeng Guo <wenfeng.guo@amlogic.com>
bing.jiang [Wed, 29 May 2019 08:24:15 +0000 (16:24 +0800)]
audio: modify loopback dts config for AVS [1/1]
PD#SWPL-9122
Problem:
AVS cannot wake up on S400_sbr
Solution:
Enable 8ch pdm + 8ch loopback
Verify:
S400 S400_SBR A113
Change-Id: Iea6ca6d55ad924a23eafbfb2b5e1f85ed57e1414
Signed-off-by: bing.jiang <bing.jiang@amlogic.com>
nengwen.chen [Wed, 8 May 2019 07:01:05 +0000 (15:01 +0800)]
atv_demod: optimize set frontend time [1/1]
PD#SWPL-8072
Problem:
optimize set frontend time.
Solution:
1.To optimize the atv demod init.
2.Turn off nicam/btsc/A2 recognition by default.
3.atv demod version: V2.11.
Verify:
Verified by x301
Change-Id: I4f894626da18fef61ce8283260e1d75adb0e3640
Signed-off-by: nengwen.chen <nengwen.chen@amlogic.com>
Zhe Wang [Fri, 17 May 2019 07:23:56 +0000 (15:23 +0800)]
audio: fixed audio hw freq responds test fail [1/2]
PD#TV-5865
Problem:
audio hdmiin freq responds test fail
Solution:
enable hw audio resample filter
Verify:
X301 marconi
Change-Id: I78699848049abe6a6b1b682e5a7bb2130fb16c09
Signed-off-by: Zhe Wang <Zhe.Wang@amlogic.com>
Evoke Zhang [Thu, 23 May 2019 05:18:21 +0000 (13:18 +0800)]
tvafe: fine tune ntsc-m recurrence [1/1]
PD#TV-6007
Problem:
ATV scan range is not qualified
Solution:
1.change 0x128 from 0x140008 to 0x1f0008 for ntsc-m
2.support cutwindow adjust debug:
echo h index val >/sys/class/tvafe/tvafe0/cutwin
echo v index val >/sys/class/tvafe/tvafe0/cutwin
echo r >/sys/class/tvafe/tvafe0/cutwin
3.support cutwindow config in dts
Verify:
x301
Change-Id: Idc3a3e8857cea2462da6edcbbf4ffefab6d48f7b
Signed-off-by: Evoke Zhang <evoke.zhang@amlogic.com>
Jian Xu [Mon, 27 May 2019 11:35:58 +0000 (19:35 +0800)]
audio: meson: fix internal codec mixer api call [1/1]
PD#TV-6267
Problem:
internal codec pointer operation error
Solution:
use 4.9 ALSA standard API to get the codec handle.
Verify:
R311
Change-Id: I52567a914230083054dc0413f818356d71c83a53
Signed-off-by: Jian Xu <jian.xu@amlogic.com>
Jihong Sui [Mon, 6 May 2019 10:12:49 +0000 (18:12 +0800)]
deinterlace: tl1: increase protection for unreg. [1/1]
PD#SWPL-7465
Problem:
1.bus crash
Solution:
1. add debug info only for tl1;
2. increase protection for unreg;
Verify:
x301
Change-Id: I84c0058bc22310f87407de1bf56f7a5eb92fd2ed
Signed-off-by: Jihong Sui <jihong.sui@amlogic.com>
Lifeng Cao [Mon, 27 May 2019 06:00:07 +0000 (14:00 +0800)]
amlvideo: reset video_inuse when amlvideo stop [1/1]
PD#TV-6189
Problem:
video_inuse always is 1 when codec server crash
Solution:
reset video_inuse when amlvideo stop
Verify:
TL1
Change-Id: I5b1b808668e3b2fb78781a4ea1ccbaefc3507d2b
Signed-off-by: Lifeng Cao <lifeng.cao@amlogic.com>
Wenfeng Guo [Fri, 24 May 2019 07:41:26 +0000 (15:41 +0800)]
vdin: fix input secam signal colorbar scale line jitter [2/2]
PD#SWPL-8878
Problem:
input secam signal colorbar scale line jitter
Solution:
setting some register for secam signal
Verify:
tl1
Change-Id: I59c370c2ab3f92c904b506d26022b165d521776c
Signed-off-by: Wenfeng Guo <wenfeng.guo@amlogic.com>
Wenfeng Guo [Fri, 24 May 2019 06:15:22 +0000 (14:15 +0800)]
deinterlace: fix input secam signal colorbar scale line jitter [1/2]
PD#SWPL-8878
Problem:
input secam signal colorbar scale line jitter
Solution:
setting some register for secam signal
Verify:
tl1
Change-Id: I0b5e1ea03581893a2b460afadcf682f3ce74b450
Signed-off-by: Wenfeng Guo <wenfeng.guo@amlogic.com>
Gongwei Chen [Wed, 29 May 2019 08:03:16 +0000 (16:03 +0800)]
audio: Speaker has no sound [1/1]
PD#IPTV-3107
Problem:
Speaker has no sound
Solution:
modify dts and
ad82584f
Verify:
Verify by Android P S905D3 AC202
Change-Id: I3dc77e5f0ba6e776b5d5ac4f34de4da9a16ec84d
Signed-off-by: GongWei Chen <gongwei.chen@amlogic.com>
Gongwei Chen [Mon, 27 May 2019 12:04:04 +0000 (20:04 +0800)]
dts: modify for S905D3 ac202 mic and loopback [1/1]
PD#SWPL-8938
Problem:
S905D3 ac202 mic and loopback
Solution:
modify gpio
Verify:
Verify by Android P ac202
Change-Id: Ibfd1711eaae0011af8f69a0fd8b35cf1a335ea8e
Signed-off-by: GongWei Chen <gongwei.chen@amlogic.com>
jintao xu [Fri, 24 May 2019 09:38:42 +0000 (17:38 +0800)]
videosync: support omx_version 3 [2/2]
PD#OTT-4036
Problem:
1.Pip path seek block.
1.playback blaock
Solution:
1.videosync support omx_version 3.
2.add pts discontinue set
Verify:
Verify on franklin.
Change-Id: I67d23a8878b1493fceb8e4f0b27598413af96e1f
Signed-off-by: jintao xu <jintao.xu@amlogic.com>
chengwang [Mon, 27 May 2019 11:46:15 +0000 (19:46 +0800)]
amvecm: HDR10+ vsif informaton confirmation [1/1]
PD#SWPL-8250
Problem:
1 check my patch to Mingliang on trunk
2 980 check vsif and frame timing confirm if vsif is one frame ahead
or not
Solution:
The data is the same as the standard of SPEC.
Verify:
on x301
Change-Id: I39ea8cb5d84c8b5b15109ed65f2428a4ec2c6c68
Signed-off-by: chengwang <cheng.wang@amlogic.com>
Evoke Zhang [Tue, 21 May 2019 15:23:49 +0000 (23:23 +0800)]
tvafe: optimize avin pali format pq for tl1 [1/1]
PD#TV-6033
Problem:
avin pal format display not good
Solution:
optimize avin pali format pq by acd_reg 0x189~0x18c,
also need update acd_reg by pq db as below value:
0x153=
40405050
0x154=401838
Verify:
x301
Change-Id: Idb2848dada3c220d3f76ffceb1d258ff177663a6
Signed-off-by: Evoke Zhang <evoke.zhang@amlogic.com>
Hui Zhang [Thu, 16 May 2019 02:45:49 +0000 (10:45 +0800)]
media_module: fix hevc back mmu dmc warnning [2/2]
PD#TV-5832
Problem:
when mmu scatter tail is freed. sometimes sao mmu is not
stopped or in idle. there is potential memory pollution
Solution:
before free unused scatter, to check hw statu idle and
diable sao mmu to avoid hevc back overwrite system memory
Verify:
X301
Change-Id: Ib784809a0946bd0a6c479a98678cb40edacc4118
Signed-off-by: Hui Zhang <hui.zhang@amlogic.com>
Wenfeng Guo [Wed, 22 May 2019 09:10:18 +0000 (17:10 +0800)]
di: fix image jitter when play DTV 3 channels [1/1]
PD#SWPL-4508
Problem:
image jitter when play DTV 3 channels
Solution:
1.force entry pulldown22
Verify:
tl1
Change-Id: I3d15ec21458fb3a6e3ae0b59910a8f350a3b1d72
Signed-off-by: Wenfeng Guo <wenfeng.guo@amlogic.com>
Long Yu [Tue, 28 May 2019 07:28:12 +0000 (15:28 +0800)]
emmc: After standby sleep, clear the CMD tuning flag [1/1]
PD#SWPL-9075
Problem:
Because the CMD tune flag was not cleared before standby,
debug printing was performed during auto tune
Solution:
After standby sleep, clear the CMD tuning flag
Verify:
passed on TL1
Change-Id: Ie4a531346f50983009477131408d81c76d5c020f
Signed-off-by: Long Yu <long.yu@amlogic.com>
Evoke Zhang [Wed, 15 May 2019 02:10:45 +0000 (10:10 +0800)]
vout: add vout2 init mode support [1/1]
PD#TV-5428
Problem:
need viu2 display support
Solution:
add vout2 init mode support
Verify:
u200
Change-Id: Ibd9d2a07645645d739d7421ceafd386caf3066d7
Signed-off-by: Evoke Zhang <evoke.zhang@amlogic.com>
Yong Qin [Thu, 23 May 2019 10:23:12 +0000 (18:23 +0800)]
vlock: verify hdmi pll from vlock for tm2 [1/1]
PD#SWPL-5620
Problem:
function verify. hdmi pll from vlock
Solution:
function verify
Verify:
tm2
Change-Id: I7b6d7ab93a1b1cf8f3ef6212d8b715e3bef44534
Signed-off-by: Yong Qin <yong.qin@amlogic.com>
zhiwei.yuan [Fri, 10 May 2019 07:43:15 +0000 (15:43 +0800)]
vdin: G12A color space error when capture screen by post blend [1/1]
PD#SWPL-8335
Problem:
color space setting error
Solution:
set yuv444 when use viu1 post blend port
Verify:
verified by t962x2_x301
Change-Id: Ic92a6db92f6cec64084d140c5f505489579b294f
Signed-off-by: zhiwei.yuan <zhiwei.yuan@amlogic.com>
Jian Xu [Sun, 26 May 2019 07:05:05 +0000 (15:05 +0800)]
audio: auge: fix the samesource spdif clock recovery issue [1/1]
PD#SWPL-3667
Problem:
after playback none-48K raw audio, the spdif clock
is not recoved to 48K when tdm/spdif same source
Solution:
use the same clock source as tdm if samesource and
config that when tdm hardware prepare.
Verify:
u212
Change-Id: I2a847273ab0b920f6cee691ee0db006709ffde2a
Signed-off-by: Jian Xu <jian.xu@amlogic.com>
Jian Cao [Fri, 17 May 2019 14:39:59 +0000 (22:39 +0800)]
ge2d: add option for rgb_to_yuv to 709 or 601 [1/1]
PD#OTT-3711
Problem:
color parameters are wrong
while displaying images on NativeImagePlayer
Solution:
add a macro BT_STANDARD for 709 or 601
Verify:
verified on W400
Change-Id: I0703ef17748c8267b86e85a4366cac88d3e41ee1
Signed-off-by: Jian Cao <jian.cao@amlogic.com>
Renjun Xu [Sat, 18 May 2019 06:19:47 +0000 (14:19 +0800)]
audio: modify loopback dts config for AVS [1/1]
PD#SWPL-8614
Problem:
AVS cannot wake up on Latest buildroot
Solution:
Enable 8ch pdm + 8ch loopback
Verify:
s420&s400
Change-Id: I93c87cc24fcbb8945f48a960383de47ad725e89e
Signed-off-by: Renjun Xu <renjun.xu@amlogic.com>
Yong Qin [Fri, 24 May 2019 01:42:15 +0000 (09:42 +0800)]
vlock: for phase lock sometime can't lock [1/1]
PD#SWPL-8946
Problem:
vlock phase lock time is not accurate as theoretical value
Solution:
1.change the limite
2.increace the frq and phase lock window
3.lone time unlock, need retry
Verify:
tl1
Change-Id: I9d47bf83969ae060f0b957739ed4c859b85c83c8
Signed-off-by: Yong Qin <yong.qin@amlogic.com>
Evoke Zhang [Wed, 22 May 2019 05:50:13 +0000 (13:50 +0800)]
cvbsout: add NTSC_M mode support [1/1]
PD#OTT-3953
Problem:
need ntsc_m mode support
Solution:
add NTSC_M mode support
Verify:
u200
Change-Id: I446862a1b9405c7acc4845d1d9116492c3e0ecca
Signed-off-by: Evoke Zhang <evoke.zhang@amlogic.com>
Pengcheng Chen [Fri, 19 Apr 2019 03:20:34 +0000 (11:20 +0800)]
ge2d: ge2d cpu cost optimize [2/2]
PD#SWPL-7422
Problem:
ge2d ioctl have cpu usage issue
Solution:
1. dma buffer alloc gdc module,when dma buf exported, fd and phys
address can be recorded.driver can get phys address via fd internally.
2. dmabuf alloc by other driver module, need used gdc_dma_buffer_map/
gdc_dma_buffer_unmap to get phys address.
Verify:
Newman & W400 board
Change-Id: I78d03b52e574daf2e8b2d53eb8fdfde06357ebfe
Signed-off-by: Pengcheng Chen <pengcheng.chen@amlogic.com>
Pengcheng Chen [Fri, 19 Apr 2019 02:58:19 +0000 (10:58 +0800)]
gdc: add gdc cpu cost optimize [1/2]
PD#SWPL-7422
Problem:
gdc ioctl have cpu usage issue
Solution:
1. dma buffer alloc gdc module,when dma buf exported, fd and phys
address can be recorded.driver can get phys address via fd internally.
2. dmabuf alloc by other driver module, need used gdc_dma_buffer_map/
gdc_dma_buffer_unmap to get phys address.
Verify:
Newman & W400 board
Change-Id: Ie270589a19dfae4fa750241fb5721154221f2448
Signed-off-by: Pengcheng Chen <pengcheng.chen@amlogic.com>
yao liu [Wed, 22 May 2019 09:38:13 +0000 (17:38 +0800)]
dolby: set gmax for LL mode [1/1]
PD#SWPL-8799
Problem:
HDR-001-TC3 GXF is brighter than VID in LL mode
Solution:
dolby_vision_target_graphics_L for LL mode
Verify:
verified on u212
Change-Id: I3b39ec048bfff3d8ae797702c1c783356d59e604
Signed-off-by: yao liu <yao.liu@amlogic.com>
shuanglong.wang [Wed, 8 May 2019 02:32:19 +0000 (10:32 +0800)]
video: for beginning playback use small omx_pts_interval_upper [1/1]
PD#SWPL-8545
Problem:
AL1 slope problem
Solution:
for beginning playback, use small omx_pts_interval_upper and
omx_pts_dv_lower to let pcr adjust according to omxpts quickly. Also
omxpts compenstion use sched_clock instead of getimeofday.
Verify:
verify by nts
Change-Id: If9476a9793e3e5da691ea720de78f1c20f01a1e5
Signed-off-by: shuanglong.wang <shuanglong.wang@amlogic.com>
Gongwei Chen [Tue, 7 May 2019 12:57:20 +0000 (20:57 +0800)]
common: loudspeaker: adjust for yeke [1/1]
PD#SWPL-8201
Problem:
loudspeaker
ad82584f for yeke.
Solution:
loudspeaker
ad82584f for yeke.
Verify:
S905D2 u202.
Change-Id: I01fe62d207c47283e714937282a0ba24aef1d467
Signed-off-by: GongWei Chen <gongwei.chen@amlogic.com>
Hanjie Lin [Thu, 13 Dec 2018 07:28:45 +0000 (15:28 +0800)]
arm: makefile: change text_offset to 0x108000 [1/1]
PD#SWPL-1505
PD#SWPL-8867
Problem:
Amlogic arm kernel text_offset is 0x208000,
ko start address to kernel text end address arrange is too big(>32M)
it can cause insmod ko failed.
Solution:
modify text_offset to 0x108000
first 0x100000 is invisibe to kernel.
Verify:
u200
Change-Id: I9684b108b57a15b03e4279146c1dc57667aa5d12
Signed-off-by: Hanjie Lin <hanjie.lin@amlogic.com>
Blance Tang [Thu, 23 May 2019 02:28:50 +0000 (10:28 +0800)]
buildroot: Add W400 DRM buildroot DTS for G12B RevB [1/1]
PD#SWPL-8830
Problem:
Current W400 DRM buildroot DTS only for G12B RevA
Solution:
Add W400 DRM buildroot DTS for G12B RevB
Verify:
Local
Change-Id: I3e01a3b53fc8d399296f6a3d777d59e0a73060c7
Signed-off-by: Blance Tang <guofeng.tang@amlogic.com>
Wencai You [Thu, 23 May 2019 12:42:51 +0000 (20:42 +0800)]
thermal: check array index when set cur_state [1/1]
PD#SWPL-8747
Problem:
android.security.sts.Poc17_11#testPocCVE_2017_6264
test echo /sys/devices/virtual/thermal/cooling_device2/cur_state
crash
Solution:
check array index
Verify:
verified by u212
Change-Id: I235d62508d95fffaed7b811ba008384db7c7ec6f
Signed-off-by: Wencai You <wencai.you@amlogic.com>
jintao xu [Tue, 21 May 2019 11:47:32 +0000 (19:47 +0800)]
amvideo: set black_threshold_height default 48 [1/1]
PD#OTT-1836
Problem:
disable video when window is too small
Solution:
set black_threshold_height default 48
Verify:
U212
Change-Id: I9ed7deb54baef1c44bb9cc0c1a4d699140663864
Signed-off-by: jintao xu <jintao.xu@amlogic.com>
Lei Qian [Thu, 23 May 2019 14:42:40 +0000 (22:42 +0800)]
vlock: fix GXL can't boot up issue [1/1]
PD#SWPL-8946
Prblem:
GXL can't boot up issue
Solution:
Revert "vlock: for phase lock sometime can't lock [1/1]"
This reverts commit
aecd88472a2c97a6793dad3e632001142f909878.
Verify:
verify by ampere
Change-Id: Ia272b379d67f84479a866b980c6f999bd7c42fa5
Signed-off-by: Lei Qian <lei.qian@amlogic.com>
Zhe Wang [Thu, 23 May 2019 06:05:14 +0000 (14:05 +0800)]
audio: remove ddr managerment print for stress test [1/1]
PD#SWPL-8755
Problem:
too much print in stress test
Solution:
remove ddr managerment print for stress test
Verify:
Verified by x301
Change-Id: Ibd2835005da2664f623504a226562d2f8d9708ba
Signed-off-by: Zhe Wang <Zhe.Wang@amlogic.com>
Brian Zhu [Wed, 22 May 2019 14:03:43 +0000 (22:03 +0800)]
vpp: set default aspect when the ratecontrol is zero [1/1]
PD#TV-5266
Problem:
Vpp used the wrong aspect ratio in 3D, screen mode = normal
and aspect ratio is 0 in ratecontrol variable.
Solution:
When the aspect ratio is 0, set the default value as
(height << 8) / width
Verify:
Verified by x301
Change-Id: I34f7cd3ce5ed1818d3090ebb4be934225038625e
Signed-off-by: Brian Zhu <brian.zhu@amlogic.com>
Jianxiong Pan [Thu, 23 May 2019 02:38:03 +0000 (10:38 +0800)]
dts: change ftrace-size. [1/1]
PD#SWPL-6028
Problem:
add ftrace-size.
Solution:
add ftrace-size.
Verify:
no.
Change-Id: I42d34edf665632dfe29d04df192964238b8e3df8
Signed-off-by: Jianxiong Pan <jianxiong.pan@amlogic.com>
Sandy Luo [Wed, 22 May 2019 15:34:13 +0000 (23:34 +0800)]
dts: tl1: change ftrace-size [1/1]
PD#SWPL-6028
Problem:
add ftrace-size
Solution:
add ftrace-size
Verify:
x301
Change-Id: I3b39deda025bde506c32ca8741876083d89038f7
Signed-off-by: Sandy Luo <sandy.luo@amlogic.com>
qiyao.zhou [Wed, 22 May 2019 11:23:10 +0000 (19:23 +0800)]
vpp: Modify vframe epoll event [1/1]
PD#SWPL-8850
Problem:
too many print when channel change.
Solution:
Modify vframe epoll event flow to avoid same event.
Verify:
verify on marconi.
Change-Id: Iefbd190c0280276bf941c48bf99706a0f2573df1
Signed-off-by: qiyao.zhou <qiyao.zhou@amlogic.com>
Evoke Zhang [Fri, 17 May 2019 06:56:15 +0000 (14:56 +0800)]
tvafe: vbi: protect vbi data byte [1/1]
PD#SWPL-8002
Problem:
some special atv cause vbi crash
Solution:
add vbi data byte protection
Verify:
x301
Change-Id: Ie890925260dc250003d375b4d1cdf3d51afe732e
Signed-off-by: Evoke Zhang <evoke.zhang@amlogic.com>
Evoke Zhang [Tue, 21 May 2019 09:23:57 +0000 (17:23 +0800)]
vdin: add dolby mem release protection [1/1]
PD#SWPL-8797
Problem:
sometime oops occurred for vdin_dolby mem release
Solution:
add vdin dolby mem alloc flag & release protection
Verify:
x301
Change-Id: Iee90b58a0624c32032e204adcd043c8e94d03f1f
Signed-off-by: Evoke Zhang <evoke.zhang@amlogic.com>
qiyao.zhou [Wed, 22 May 2019 07:43:15 +0000 (15:43 +0800)]
vpp: Modify vframe epoll event [1/1]
PD#SWPL-8850
Problem:
too many print when channel change.
Solution:
Modify vframe epoll event flow to avoid same event.
Verify:
verify on marconi.
Change-Id: Id709439f24d3cad82df6082c477cacce1a9b9cc7
Signed-off-by: qiyao.zhou <qiyao.zhou@amlogic.com>
Wenfeng Guo [Thu, 9 May 2019 03:04:08 +0000 (11:04 +0800)]
di: fix wire drawing issue caused by pendulum clock stuck [1/1]
PD#SWPL-7650
Problem:
TL1 have drawing.
Solution:
fine-tuning GMV
Verify:
TL1
Change-Id: Ie50207969a2d7511882552b0adc8baef083300ff
Signed-off-by: Wenfeng Guo <wenfeng.guo@amlogic.com>
Yong Qin [Mon, 20 May 2019 02:02:25 +0000 (10:02 +0800)]
vlock: for phase lock sometime can't lock [1/1]
PD#SWPL-6403
Problem:
vlock phase lock time is not accurate as theoretical value
Solution:
1.change the limite
2.increace the frq and phase lock window
3.lone time unlock, need retry
Verify:
tl1
Change-Id: I67e56e59f53848128e65a54c6a8acf750a03b72d
Signed-off-by: Yong Qin <yong.qin@amlogic.com>
Evoke Zhang [Thu, 25 Apr 2019 02:39:13 +0000 (10:39 +0800)]
lcd: support custom vx1 hw filter [1/1]
PD#SWPL-8785
Problem:
fixed vx1 hw filter maybe cause some panel display normal
Solution:
add custom vx1 hw filter support
for panel ini:
if_attr_8=0x1 #vx1 hw filter period(0=default setting)
if_attr_9=0x0 #vx1 hw filter cnt(0=default setting)
for dts:
hw_filter = <0x1 0x0>; /* period(0=default), cnt(0=default) */
Verify:
x301
Change-Id: I4ce5f8fe4294331d6ec0026fa7736c6d3397c05e
Signed-off-by: Evoke Zhang <evoke.zhang@amlogic.com>
ruixuan.li [Tue, 2 Apr 2019 12:37:38 +0000 (20:37 +0800)]
tm2: emmc run hs400 200M [1/1]
PD#SWPL-5658
Problem:
emmc run hs200 200M now
Solution:
set emmc busmode to hs400 200M
Verify:
passed on t962e2 ab311
Change-Id: If5fef5c3b55cc95152b0d5d19bb5a56b293aafcf
Signed-off-by: ruixuan.li <ruixuan.li@amlogic.com>
Signed-off-by: Ruixuan Li <ruixuan.li@amlogic.com>
Long Yu [Tue, 14 May 2019 07:17:30 +0000 (15:17 +0800)]
emmc: report response crc error on G12B when hs400 200M busmode [1/1]
PD#SWPL-8670
Problem:
G12B report response crc error when hs400 200M busmode
Solution:
find a eyetest hole between 14-20 or 48-54, otherwise
tuning tx_delay and find again and
adjust CMD rx timing dynamically in HS400 mode
Verify:
passed on G12B
Change-Id: I23e4d5118e0ca0564367a77102aea9e1085633a9
Signed-off-by: Long Yu <long.yu@amlogic.com>
yao liu [Wed, 8 May 2019 13:55:45 +0000 (21:55 +0800)]
dolby: set dovi gmax/pmax [1/1]
PD#SWPL-8159
Problem:
Default graphics is always 100nit,
need to set different nits for SDR/HDR/DV TV
Solution:
dolby_vision_target_graphics_max[] for DV/HDR/SDR;
dolby_vision_target_max[][] for video_max;
module param dolby_vision_target_max for force graphics max
when set it to non-zero;
Verify:
verified on sm1
Change-Id: If6f5ae4ffb37629b51d21764302689da776e9f7f
Signed-off-by: yao liu <yao.liu@amlogic.com>
renjiang.han [Mon, 20 May 2019 08:30:59 +0000 (16:30 +0800)]
ppmgr: 4k video does not do tb detection. [1/1]
PD#SWPL-8338
Problem:
video of 4k playback caton.
Solution:
4k video does not do tb detection.
Verify:
on x301
Change-Id: Idf10ca33e7ba2d26d759c6e5c21bc465cad0992e
Signed-off-by: renjiang.han <renjiang.han@amlogic.com>
nengwen.chen [Mon, 20 May 2019 05:39:13 +0000 (13:39 +0800)]
atv_demod: fix BG/DK sound output power [1/1]
PD#TV-6012
Problem:
fix BG/DK sound output power.
Solution:
1.fix BG/DK sound output power.
Verify:
Verified by x301
Change-Id: I428d8a1ed97c8da5fdfe55f8dd7ac2fda9200814
Signed-off-by: nengwen.chen <nengwen.chen@amlogic.com>
Yue Wang [Thu, 16 May 2019 09:21:37 +0000 (17:21 +0800)]
pcie: code optimization [1/1]
PD#SWPL-8664
Problem:
pcie driver code optimization.
Solution:
pcie driver code optimization.
Verify:
T962E2
Change-Id: Ie157ad14a7a3b347bfb333e75432863d3e988dec
Signed-off-by: Yue Wang <yue.wang@amlogic.com>
Tao Zeng [Tue, 14 May 2019 10:18:09 +0000 (18:18 +0800)]
secmon: clear mmu mapping of cma before a73 run [1/1]
PD#SWPL-8082
Problem:
Very low ratio(0.3%) of SError can be seen when do auto-reboot
test on g12b platfrom.
Solution:
Clear mmu mapping of secmon cma before a73 run
Verify:
w400
Change-Id: Idacfaea29dea2eff86304c7071a560c76654a5c3
Signed-off-by: Tao Zeng <tao.zeng@amlogic.com>
Nanxin Qin [Thu, 20 Sep 2018 17:18:20 +0000 (01:18 +0800)]
media: fixed some issues for the v4l2 decode. [2/2]
PD#SWPL-5314
Problem:
1. add a dummy vframe flag VFRAME_FLAG_EMPTY_FRAME_V4L.
2. add the FRAME_BASE_PATH_V4L_* for v4l2 display
3. recycle vframes when the isr recevie the empty vframe.
Solution:
1. fixed some issues for the v4l2 decode.
2. add pause and resume for v4l2 m2m job.
Verify:
todo
Change-Id: I00b44ad4d3a75f7e2167ca347562d002c2690430
Signed-off-by: Nanxin Qin <nanxin.qin@amlogic.com>
Jian Hu [Mon, 20 May 2019 06:46:03 +0000 (14:46 +0800)]
clk: tm2: fix tm2 64bit hangup [1/1]
PD#SWPL-8546
Problem:
it hangup in tm2 64bit
Solution:
call clk_set_parent to set
tl1_dsu_fixed_source_sel1 to 1G
Verify:
verified on tm2 ab311
Change-Id: I2e75c76aab3ba2510050592ea5f6c3069cfa9f4d
Signed-off-by: Jian Hu <jian.hu@amlogic.com>
Yinming Ding [Tue, 23 Apr 2019 12:15:49 +0000 (20:15 +0800)]
avsync: tsync: reply the stream without audio after loop play [1/1]
PD#SWPL-7379
Problem:
Decoding stream with no audio pid freezes video
Solution:
Reply the stream with no audio after loop play
Verify:
Verified by R314
Change-Id: I8782271fbf40398c639346c960f0e61911ffc1ee
Signed-off-by: Yinming Ding <yinming.ding@amlogic.com>
Hanjie Lin [Thu, 16 May 2019 05:38:20 +0000 (13:38 +0800)]
mm: arm: fix unmatched pte_offset_map/pte_unmap error [1/1]
PD#TV-5777
Problem:
[CVTE][T972][9.0][System]: PT190004-1300: Appear auto reboot exception
during downloading Facebook app.
get_user_pfn() may caused unmatched pte_offset_map/pte_unmap call, then
may cause bad task preempt_count and subsequently panic.
Solution:
add matched pte_offset_map/pte_unmap
Verify:
tl1
Change-Id: I98240b443b8a0fae89d0ee93701eb1bfdce51b82
Signed-off-by: Hanjie Lin <hanjie.lin@amlogic.com>
Zhe Wang [Mon, 13 May 2019 06:56:25 +0000 (14:56 +0800)]
audio: add i2s and spdif fine clk tuning interface [1/1]
PD#SWPL-8310
Problem:
DTV, a/v is out of sync
Solution:
add i2s and spdif fine clk tuning interface
Verify:
verify on R311.
Change-Id: I8219774bd5fe334fa21227d427ce4dbb06177dc8
Signed-off-by: Zhe Wang <Zhe.Wang@amlogic.com>
Brian Zhu [Thu, 16 May 2019 13:13:56 +0000 (21:13 +0800)]
dv: reset the g_vpotch value according to current vinfo [1/1]
PD#SWPL-8419
Problem:
Get the wrong g_vpotch value when platform bootup
Solution:
reset the g_vpotch value according to current vinfo
Verify:
verified by u212
Change-Id: I063140f0a19cf349cd8e6d66c571ae5b2c7e3de7
Signed-off-by: Brian Zhu <brian.zhu@amlogic.com>
MingLiang Dong [Mon, 29 Apr 2019 09:12:59 +0000 (05:12 -0400)]
amvecm: optimize lc size config [1/1]
PD#TV-4687
Problem:
Set the screen mode of HDMI channel to 4:3 and
restart to enter HDMI again. The screen displays abnormal
Solution:
optimize lc size config
Verify:
verify on TL1
Change-Id: I320f7476e09d900635767190748a4fbb486b5f6f
Signed-off-by: MingLiang Dong <mingliang.dong@amlogic.com>
nengwen.chen [Fri, 17 May 2019 07:08:00 +0000 (15:08 +0800)]
atv_demod: fix atbm2040 tuner channel scanning [1/1]
PD#TV-5499
Problem:
fix atbm2040 tuner channel scanning.
Solution:
1.fix atbm2040 tuner channel scanning.
2.modify tune interface.
Verify:
Verified by x301
Change-Id: Id135bcdca797ab93e8a2902476157b2ce324a2ce
Signed-off-by: nengwen.chen <nengwen.chen@amlogic.com>
yujie.wu [Thu, 11 Apr 2019 02:38:54 +0000 (10:38 +0800)]
audio: fix spdif not work on soundbar [1/1]
PD#SWPL-6801
Problem:
There is too much kernel print which
blocks the system
Solution:
Add condition to remove the print log
Verify:
A113
Change-Id: I5762893b424e8201e2725f33854473097f1246b9
Signed-off-by: yujie.wu <yujie.wu@amlogic.com>
Shunzhou Jiang [Mon, 13 May 2019 08:45:33 +0000 (16:45 +0800)]
dts: tm2: enable dsp mailbox driver [1/1]
PD#SWPL-6580
Problem:
dsp mailbox driver not enabled
Solution:
enable dsp mbox driver
Verify:
tm2
Change-Id: I926c6da3fd373bd19cc171514096e90d929a5807
Signed-off-by: Shunzhou Jiang <shunzhou.jiang@amlogic.com>
shaochan.liu [Mon, 13 May 2019 10:14:24 +0000 (18:14 +0800)]
lcd: support lcd pll retry when lock failed [2/2]
PD#SWPL-7869
Problem:
need support lcd pll retry when lock failed
Solution:
add support lcd pll retry when lock failed
Verify:
t962x2-x301
Change-Id: Ia74926713f46c7e1fc2831c9ee788c5fc980ba37
Signed-off-by: shaochan.liu <shaochan.liu@amlogic.com>
Jianxin Pan [Mon, 20 May 2019 02:15:14 +0000 (19:15 -0700)]
Merge "lcd: add lcd_ctrl bootargs for lcd driver control [2/2]" into amlogic-4.9-dev
Evoke Zhang [Fri, 17 May 2019 09:09:22 +0000 (17:09 +0800)]
tvafe: update parameters for AV NTSC [1/1]
PD#SWPL-7283
Problem:
display is not good
Solution:
modify cvd2 0xb0, 0xb1 reg value
Verify:
x301
Change-Id: Ib512258336d3a6bb14c4eda04488fbaf60e38af0
Signed-off-by: Evoke Zhang <evoke.zhang@amlogic.com>
Yong Qin [Tue, 14 May 2019 01:43:55 +0000 (09:43 +0800)]
vdin: horizontal floral stripe [1/1]
PD#SWPL-7391
Problem:
when hdmi 4k, tv menu set game mode, some time have
floral stripe
Solution:
afbc write addr is same at read addr, will occur.
Verify:
tl1
Change-Id: Iac10768116dea0d3bc4175871b954d56b044f390
Signed-off-by: Yong Qin <yong.qin@amlogic.com>
Tao Zeng [Thu, 16 May 2019 09:28:29 +0000 (17:28 +0800)]
kasan: change address layout [3/3]
PD#SWPL-8572
Problem:
In change http://scgit.amlogic.com:8080/#/c/73995/ we have changed
memory layout of vmalloc. Which caused kasan can't be used
Solution:
change kasan address layout
Verify:
x301
Change-Id: I28aee4b1d9b622dd884e6c2d6b621aa870cd8586
Signed-off-by: Tao Zeng <tao.zeng@amlogic.com>
projects / platform / kernel / linux-amlogic.git / log