Pali Rohár [Sun, 4 Sep 2022 01:29:05 +0000 (03:29 +0200)]
Nokia RX-51: Add comment describing kernel image type into test script
Signed-off-by: Pali Rohár <pali@kernel.org>
Pali Rohár [Sun, 4 Sep 2022 01:29:04 +0000 (03:29 +0200)]
Nokia RX-51: Do not set useless ARCH= in test script
U-Boot ignores ARCH= variable.
Signed-off-by: Pali Rohár <pali@kernel.org>
Pali Rohár [Sun, 4 Sep 2022 01:29:03 +0000 (03:29 +0200)]
Nokia RX-51: Fix documentation how to enable UBI support
Disable UBI fastmap support which is not supported by original Maemo 5
kernel and explicitly set UBI BEB limit to 10%, which is the value used by
original Maemo 5 kernel. U-Boot default value is 20%.
Signed-off-by: Pali Rohár <pali@kernel.org>
Pali Rohár [Sun, 4 Sep 2022 01:29:02 +0000 (03:29 +0200)]
Nokia RX-51: Call bootm in test script only when image is valid
When reading of image fails then do not call bootm. This prevents false
positive test result in case something bootable is present in memory.
Signed-off-by: Pali Rohár <pali@kernel.org>
Pali Rohár [Sun, 4 Sep 2022 01:29:01 +0000 (03:29 +0200)]
Nokia RX-51: Change UBIFS volume size to 1870 LEBs in test script
Original Nokia UBIFS system image has 1870 LEBs, so set UBIFS volume size
in test script to the same value. Number of 1870 LEBs corresponds to 230MiB
(LEB size * num of LEBs = 126KiB * 1870 = 230MiB).
Signed-off-by: Pali Rohár <pali@kernel.org>
Pali Rohár [Sun, 4 Sep 2022 01:29:00 +0000 (03:29 +0200)]
Nokia RX-51: Set default SYS_LOAD_ADDR to 0x80008000
At address 0x80000100 are stored initial atags passed to U-Boot by NOLO.
So do not overwrite them when using $loadaddr variable which value is set
from CONFIG_SYS_LOAD_ADDR option.
Signed-off-by: Pali Rohár <pali@kernel.org>
Pali Rohár [Sun, 4 Sep 2022 01:28:59 +0000 (03:28 +0200)]
Nokia RX-51: Do not clear unknown memory in lowlevel_init.S
If kernel image in uImage or zImage format is not detected by
lowlevel_init.S code then do not clear memory location where image was
expected. If image is not detected then this memory region is unknown.
So do not unconditionally clear it.
Signed-off-by: Pali Rohár <pali@kernel.org>
Pali Rohár [Sun, 4 Sep 2022 01:28:58 +0000 (03:28 +0200)]
Nokia RX-51: Remove label copy_kernel_start from lowlevel_init.S
Label copy_kernel_start is now unused. Remove it.
Signed-off-by: Pali Rohár <pali@kernel.org>
Jayesh Choudhary [Tue, 30 Aug 2022 10:24:30 +0000 (15:54 +0530)]
configs: Add configs for j721s2 High Security EVM
Add j721s2 High Security EVM defconfig.
These configs are same as for the non-secure part, except for:
CONFIG_TI_SECURE_DEVICE option set to 'y'
CONFIG_FIT_IMAGE_POST_PROCESS option set to 'y'
CONFIG_SPL_FIT_IMAGE_POST_PROCESS option set to 'y'
CONFIG_BOOTCOMMAND uses FIT images for booting
Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
Andrew Davis [Tue, 30 Aug 2022 10:24:29 +0000 (15:54 +0530)]
configs: Add configs for J7200 High Security EVM
Add J7200 High Security EVM defconfig.
These defconfigs are the same as for the non-secure part, except for:
CONFIG_TI_SECURE_DEVICE option set to 'y'
CONFIG_BOOTCOMMAND uses FIT images for booting
Signed-off-by: Andrew Davis <afd@ti.com>
[j-choudhary@ti.com: add few configs from GP variant which were missing]
Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
Bernhard Messerklinger [Thu, 25 Aug 2022 06:54:04 +0000 (08:54 +0200)]
brppt1: Update environment to support new boot concept
* Drop legacy /boot/PPTImage.md5 check
* Update device tree naming
* Update t30args#0 root cmd line property to support latest kernel
versions (root=/dev/mmcblk0p2 for linux < 4 and
root=/dev/mmcblk1p2 for linux >= 4)
* Add custom bootloader version string
* Destroy invalid dtb at ${dtbaddr} and configuration script at
${cfgaddr} to ensure proper boot in warm restart case.
Signed-off-by: Bernhard Messerklinger <bernhard.messerklinger@br-automation.com>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Bernhard Messerklinger [Thu, 25 Aug 2022 06:54:03 +0000 (08:54 +0200)]
include: configs: brppt1: Fix commit
0ea4fc4dcf90
Commit
0ea4fc4dcf90 ("board/BuR: invalidate ${dtbaddr} before cfgscr")
destroys the boot targets b_t30lgcy#0 and b_t30lgcy#1. The reason behind
this is, that b_t30lgcy#0 and b_t30lgcy#1 both load the for booting
needed device trees from mmc and the cfgscr script patches those. Because
of this, cfgscr is not allowed to destroy the previously loaded device
tree otherwise cfgscr will fail.
This patch moves the device trees invalidation on warm restart to the
PREBOOT cmd to fix that issue.
Fixes:
0ea4fc4dcf90 ("board/BuR: invalidate ${dtbaddr} before cfgscr")
Signed-off-by: Bernhard Messerklinger <bernhard.messerklinger@br-automation.com>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Bernhard Messerklinger [Thu, 25 Aug 2022 06:54:02 +0000 (08:54 +0200)]
brppt1: Cleanup device tree
* Remove unnecessary device tree nodes which are not needed in
U-Boot directly.
* Move all U-Boot specific device tree properties to u-boot dtsi.
Signed-off-by: Bernhard Messerklinger <bernhard.messerklinger@br-automation.com>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Bernhard Messerklinger [Thu, 25 Aug 2022 06:54:01 +0000 (08:54 +0200)]
brppt1: Fix SPL boot stage
Commit
6337d53fdf45 ("arm: dts: sync am33xx with Linux 5.9-rc7") syncs
the am335x device tree with the latest linux kernel am335x device tree.
That causes problems with device tree in SPL stage.
To fix the issues CONFIG_SPL_OF_TRANSLATE must be set to handle the
synced bus addresses correctly.
A custom U-Boot device tree is also needed since the SPL build removes
bus properties from bus nodes which are not explicitly marked with the
u-boot,dm-spl or u-boot,dm-pre-reloc flag. Therefore all parent buses of
the in the SPL needed devices must be marked with u-boot,dm-pre-reloc.
Also since there is no driver for "ti,sysc" compatible property in SPL
the buses marked with this compatible string must also be marked with
compatible = "simple-bus" to make the underlying devices visible in
SPL. Otherwise the matching device drivers aren't found and the uclass
drivers are dropped.
Signed-off-by: Bernhard Messerklinger <bernhard.messerklinger@br-automation.com>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Bernhard Messerklinger [Thu, 25 Aug 2022 06:54:00 +0000 (08:54 +0200)]
brppt1: Remove unused board variants
The SPI and NAND board variants never went into production.
Drop those board variants.
Signed-off-by: Bernhard Messerklinger <bernhard.messerklinger@br-automation.com>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Tom Rini [Thu, 15 Sep 2022 13:59:47 +0000 (09:59 -0400)]
Merge branch '2022-09-15-general-improvements' into next
- Add uncompressed kernel image support to falcon mode, TEE
improvements, make xyz-modem timeout configurable, gpio updates and
other assorted improvements.
Heinrich Schuchardt [Wed, 31 Aug 2022 19:13:40 +0000 (21:13 +0200)]
lib: rsa: fix padding_pss_verify
Check the that the hash length is shorter than the message length. This
avoids:
./tools/../lib/rsa/rsa-verify.c:275:11: warning:
‘*db’ may be used uninitialized [-Wmaybe-uninitialized]
275 | db[0] &= 0xff >> leftmost_bits;
Fixes:
061daa0b61f0 ("rsa: add support of padding pss")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Sean Anderson [Tue, 30 Aug 2022 20:40:37 +0000 (16:40 -0400)]
cli: Reduce size of readline buffers in SPL
Normally, readline is not used int SPL. However, it may be useful to
enable the Freescale DDR interactive mode in SPL, while U-Boot is still
executing from SRAM. The default settings for readline result in a large
buffer being allocated. Reduce the size of the maximum input line, and
the number of lines of scrollback when building for SPL.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Patrice Chotard [Tue, 30 Aug 2022 12:09:14 +0000 (14:09 +0200)]
gpio: sandbox: Add GPIOD_IS_AF for gpio configured in alternate function
This allows to test if a pin's label if displayed using gpio_get_status()
when this pin is configured in alternate function.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Patrice Chotard [Tue, 30 Aug 2022 12:09:13 +0000 (14:09 +0200)]
pinctrl: pinctrl_stm32: Populate uc_priv->name[] with pinmux node's name
Populate uc_priv->name[] with pinmux node's name in order to indicate
the pinmuxing's name in case GPIO is configured in alternate.
For example, for STM32 SoC's based platform, "gpio status" command
output :
before
Bank GPIOZ:
GPIOZ0: unused : 0 [ ]
GPIOZ1: unused : 0 [ ]
GPIOZ2: unused : 0 [ ]
GPIOZ3: unused : 0 [ ]
GPIOZ4: func
GPIOZ5: func
GPIOZ6: unused : 0 [ ]
GPIOZ7: unused : 0 [ ]
GPIOZ8: unknown
GPIOZ9: unknown
GPIOZ10: unknown
GPIOZ11: unknown
GPIOZ12: unknown
GPIOZ13: unknown
GPIOZ14: unknown
GPIOZ15: unknown
After
Bank GPIOZ:
GPIOZ0: unused : 0 [ ]
GPIOZ1: unused : 0 [ ]
GPIOZ2: unused : 0 [ ]
GPIOZ3: unused : 0 [ ]
GPIOZ4: func i2c4-0
GPIOZ5: func i2c4-0
GPIOZ6: unused : 0 [ ]
GPIOZ7: unused : 0 [ ]
GPIOZ8: unknown
GPIOZ9: unknown
GPIOZ10: unknown
GPIOZ11: unknown
GPIOZ12: unknown
GPIOZ13: unknown
GPIOZ14: unknown
GPIOZ15: unknown
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Patrice Chotard [Tue, 30 Aug 2022 12:09:12 +0000 (14:09 +0200)]
gpio: Fix pin's status display for pin with GPIOF_UNUSED function
Even pin with GPIOF_UNUSED function can have a label.
The criteria to add or not a space character is linked to label not to
the used/unused status.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Patrice Chotard [Tue, 30 Aug 2022 12:09:11 +0000 (14:09 +0200)]
gpio: Allow to print pin's label even for pin with GPIOF_FUNC function
Currently, if pin's function is GPIOF_FUNC, only "func" if displayed
without any other information. It would be interesting, if information is
available, to indicate which pinmuxing's name is used.
For example, for STM32 SoC's based platform, "gpio status" command
output :
before
Bank GPIOZ:
GPIOZ0: unused : 0 [ ]
GPIOZ1: unused : 0 [ ]
GPIOZ2: unused : 0 [ ]
GPIOZ3: unused : 0 [ ]
GPIOZ4: func
GPIOZ5: func
GPIOZ6: unused : 0 [ ]
GPIOZ7: unused : 0 [ ]
GPIOZ8: unknown
GPIOZ9: unknown
GPIOZ10: unknown
GPIOZ11: unknown
GPIOZ12: unknown
GPIOZ13: unknown
GPIOZ14: unknown
GPIOZ15: unknown
After
Bank GPIOZ:
GPIOZ0: unused : 0 [ ]
GPIOZ1: unused : 0 [ ]
GPIOZ2: unused : 0 [ ]
GPIOZ3: unused : 0 [ ]
GPIOZ4: func i2c4-0
GPIOZ5: func i2c4-0
GPIOZ6: unused : 0 [ ]
GPIOZ7: unused : 0 [ ]
GPIOZ8: unknown
GPIOZ9: unknown
GPIOZ10: unknown
GPIOZ11: unknown
GPIOZ12: unknown
GPIOZ13: unknown
GPIOZ14: unknown
GPIOZ15: unknown
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Xiang W [Sun, 28 Aug 2022 23:53:15 +0000 (07:53 +0800)]
virtio: pci: fix bug of virtio_pci_map_capability
The bar of the structure virtio_pci_cap is the index, and each base
address occupies 4 bytes, so it needs to be multiplied by 4.
This patch fixes a bug reported by Felix Yan
https://lists.denx.de/pipermail/u-boot/2022-August/492779.html
Signed-off-by: Xiang W <wxjstz@126.com>
Tested-by: Felix Yan <felixonmars@archlinux.org>
Alexander Sowarka [Sun, 28 Aug 2022 19:30:20 +0000 (21:30 +0200)]
nvme: Fix multipage prp-list
The nvme driver falsely assumed that the last entry on a page
of the prp-list always points to the next page of the prp-list.
This potentially can lead to the illegal creation of pages on
the prp-list with only a single entry. This change now ensures
that splitting the prp-list into multiple pages, behaves now as
required by the NVME-Spec.
Related to this, also the size of the memory allocation is adjusted
accordingly.
Signed-off-by: Alexander Sowarka <alexander.sowarka@aerq.com>
Pali Rohár [Mon, 29 Aug 2022 15:36:23 +0000 (17:36 +0200)]
doc: cmd: loady: Document new configuration
Signed-off-by: Pali Rohár <pali@kernel.org>
Pali Rohár [Sat, 27 Aug 2022 14:37:55 +0000 (16:37 +0200)]
xyz-modem: Allow to configure initial timeout for loadx and loady
Now when loadx and loady commands could be aborted / cancelled by CTRL+C,
allow to configure timeout for initial x/y-modem packet via env variable
$loadxy_timeout and by default use value from new compile-time config
option CONFIG_CMD_LOADXY_TIMEOUT. Value is in seconds and zero value means
infinite timeout. Default value is 90s which is the value used before this
change for loadx command.
Other load commands loadb and loads already waits infinitely. Same behavior
for loadx and loady commands can be achieved by setting $loadxy_timeout or
CONFIG_CMD_LOADXY_TIMEOUT to 0.
Signed-off-by: Pali Rohár <pali@kernel.org>
Sean Anderson [Tue, 23 Aug 2022 19:10:39 +0000 (15:10 -0400)]
post: memory: Fix format strings
This fixes numerous cases of format strings not matching their
arguments. Also keep the format strings on one line for easier grepping.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Etienne Carriere [Tue, 26 Jul 2022 14:21:43 +0000 (16:21 +0200)]
drivers: rng: optee_rng: register to CONFIG_OPTEE_SERVICE_DISCOVERY
Changes optee_rng driver to register itself has a OP-TEE service so
that a device is bound for the driver when OP-TEE enumerates the
PTA RNG service.
Cc: Sughosh Ganu <sughosh.ganu@linaro.org>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Etienne Carriere [Tue, 26 Jul 2022 14:21:42 +0000 (16:21 +0200)]
drivers: tee: optee: discover OP-TEE services
This change defines resources for OP-TEE service drivers to register
themselves for being bound to when OP-TEE firmware reports the related
service is supported. OP-TEE services are discovered during optee
driver probe sequence which mandates optee driver is always probe once
bound.
Discovery of optee services and binding to related U-Boot drivers is
embedded upon configuration switch CONFIG_OPTEE_SERVICE_DISCOVERY.
Cc: Jens Wiklander <jens.wiklander@linaro.org>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Etienne Carriere [Tue, 26 Jul 2022 14:21:41 +0000 (16:21 +0200)]
drivers: tee: optee: remove unused probe local variable
Removes local variable child in optee_probe() that is not used.
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Stefan Herbrechtsmeier [Tue, 14 Jun 2022 14:12:00 +0000 (16:12 +0200)]
spl: fit: Allocate buffers aligned to cache line size
Allocate memory for buffers at a cache-line boundary to avoid
misaligned buffer address for subsequent reads. This avoids an
additional sector-based memory copy in the fat file system driver:
FAT: Misaligned buffer address (...)
Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
Stefan Herbrechtsmeier [Tue, 14 Jun 2022 13:21:31 +0000 (15:21 +0200)]
misc: usb251xb: Support 8/16 bit device tree values
The device tree binding [1] specify the vendor-id, product-id, device-id
and language-id as 16 bit values and the linux driver reads the boost-up
value as 8 bit value.
[1] https://www.kernel.org/doc/Documentation/devicetree/bindings/usb/usb251xb.txt
Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Stefan Herbrechtsmeier [Tue, 14 Jun 2022 13:21:30 +0000 (15:21 +0200)]
dm: core: Add functions to read 8/16-bit integers
Add functions to read 8/16-bit integers like the existing functions for
32/64-bit to simplify read of 8/16-bit integers from device tree
properties.
Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Nathan Barrett-Morrison [Wed, 2 Feb 2022 20:05:18 +0000 (15:05 -0500)]
Add in the ability to load and boot an uncompressed kernel image during the Falcon Mode boot sequence.
This is required for architectures which do not support compressed kernel images (i.e. ARM64). This is only used while not booting via FIT image.
Signed-off-by: Nathan Barrett-Morrison <nathan.morrison@timesys.com>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Tom Rini [Wed, 14 Sep 2022 16:31:44 +0000 (12:31 -0400)]
Merge tag 'efi-next-2022-09-14' of https://source.denx.de/u-boot/custodians/u-boot-efi into next
Pull request for efi next
UEFI:
Implement a command eficonfig to maintain Load Options and boot order via
menus.
Tom Rini [Wed, 14 Sep 2022 15:50:21 +0000 (11:50 -0400)]
Merge branch '2022-09-14-refactor-ramdisk-code-again' into next
To quote the author:
The previous attempt at this[1] broke a board and was reverted in [2].
This series adopts a slightly different approach, splitting the changes
into many commits.
[1]
f33a2c1bd0f ("image: Remove #ifdefs from select_ramdisk()")
[2]
621158d106f ("Revert "image: Remove #ifdefs from select_ramdisk()"")
Simon Glass [Sun, 28 Aug 2022 18:32:53 +0000 (12:32 -0600)]
image: Drop some other #ifdefs in image-board.c
Remove all but a few that are difficult, relying on legacy CONFIG options
or optional global_data fields.
Drop the duplicate function name in the comment for boot_get_cmdline().
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Sun, 28 Aug 2022 18:32:52 +0000 (12:32 -0600)]
image: Correct indentation in select_ramdisk()
Finish off the refactoring by correcting the indent levels. Note that this
does not include any functional changes.
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Sun, 28 Aug 2022 18:32:51 +0000 (12:32 -0600)]
image: Drop remaining FIT #ifdef
Drop the last one of these, by using a done_select variable to control
whether to fall back to using 'select' as a hex value.
Note that the indentation is not adjusted, to make this easier to review.
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Sun, 28 Aug 2022 18:32:50 +0000 (12:32 -0600)]
image: Drop another #ifdef for FIT
Drop the prenultimate one of these from select_ramdisk().
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Sun, 28 Aug 2022 18:32:49 +0000 (12:32 -0600)]
image: Drop one #ifdef for FIT
Drop the #ifdef from near the end of select_ramdisk(). Move some variables
to the top of the function to make this work.
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Sun, 28 Aug 2022 18:32:48 +0000 (12:32 -0600)]
image: Drop #ifdefs for LEGACY_IMAGE_FORMAT
Use if() instead of the #ifdef in select_ramdisk().
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Sun, 28 Aug 2022 18:32:47 +0000 (12:32 -0600)]
image: Track when ramdisk processing is completed
The current switch default is tricky since it relies on #ifdefs to work.
Use a bool instead.
Also fix the comment on @select, since it has a dual purpose.
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Sun, 28 Aug 2022 18:32:46 +0000 (12:32 -0600)]
image: Fix up ANDROID_BOOT_IMAGE ramdisk code
Convert this to an if(), fix the cast from an address to a pointer and
make sure that any error is returned correctly.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tom Rini [Wed, 14 Sep 2022 12:57:39 +0000 (08:57 -0400)]
Merge branch '2022-09-13-add-support-for-cyclic-function-execution' into next
To quote the author:
This patchset adds the basic infrastructure to periodically execute
code, e.g. all 100ms. Examples for such functions might be LED blinking
etc. The functions that are hooked into this cyclic list should be
small timewise as otherwise the execution of the other code that relies
on a high frequent polling (e.g. UART rx char ready check) might be
delayed too much. This patch also adds the Kconfig option
CONFIG_CYCLIC_MAX_CPU_TIME_US, which configures the max allowed time
for such a cyclic function. If it's execution time exceeds this time,
this cyclic function will get removed from the cyclic list.
How is this cyclic functionality executed?
This patchset integrates the main function responsible for calling all
registered cyclic functions cyclic_run() into the common WATCHDOG_RESET
macro. This guarantees that cyclic_run() is executed very often, which
is necessary for the cyclic functions to get scheduled and executed at
their configured periods.
This cyclic infrastructure will be used by a board specific function on
the NIC23 MIPS Octeon board, which needs to check periodically, if a
PCIe FLR has occurred.
Ideas how to continue:
One idea is to rename WATCHDOG_RESET to something like SCHEDULE and
move the watchdog_reset call into this cyclic infrastructure as well.
Or to perhaps move the shell UART RX ready polling to a cyclic
function.
It's also possible to extend the "cyclic" command, to support the
creation of periodically executed shell commands (for testing etc).
Masahisa Kojima [Mon, 12 Sep 2022 08:33:59 +0000 (17:33 +0900)]
test: unit test for eficonfig
Provide a unit test for the eficonfig command.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Masahisa Kojima [Mon, 12 Sep 2022 08:33:58 +0000 (17:33 +0900)]
doc:eficonfig: add documentation for eficonfig command
Add documentation for eficonfig command.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Masahisa Kojima [Mon, 12 Sep 2022 08:33:57 +0000 (17:33 +0900)]
doc:bootmenu: add description for UEFI boot support
The bootmenu enumerates the UEFI boot options
for boot device selection.
This commit adds the description how the UEFI boot work
in bootmenu. This commit also adds "Synopsis", "Description"
and "Configuration" sections to follow the U-Boot command
documentation format.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Masahisa Kojima [Mon, 12 Sep 2022 08:33:56 +0000 (17:33 +0900)]
eficonfig: add "Change Boot Order" menu entry
This commit adds the menu entry to update UEFI BootOrder variable.
User moves the entry with UP/DOWN key, changes the order
with PLUS/MINUS key, press SPACE to activate or deactivate
the entry, then finalizes the order by ENTER key.
If the entry is activated, the boot index is added into the
BootOrder variable in the order of the list.
The U-Boot menu framework is well designed for static menu,
this commit implements the own menu display and key handling
for dynamically change the order of menu entry.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Masahisa Kojima [Mon, 12 Sep 2022 08:33:55 +0000 (17:33 +0900)]
eficonfig: scan media device in eficonfig startup
In eficonfig startup, scan media devices and update
the UEFI boot option.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Masahisa Kojima [Mon, 12 Sep 2022 08:33:54 +0000 (17:33 +0900)]
bootmenu: add removable media entries
UEFI specification requires booting from removal media using
a architecture-specific default image name such as BOOTAA64.EFI.
This commit adds the removable media entries into bootmenu,
so that user can select the removable media and boot with
default image.
The bootmenu automatically enumerates the possible bootable
media devices supporting EFI_SIMPLE_FILE_SYSTEM_PROTOCOL,
add it as new UEFI boot option(BOOT####) and update BootOrder
variable. This automatically generated UEFI boot option
has the dedicated guid in the optional_data to distinguish it from
the UEFI boot option user adds manually. This optional_data is
removed when the efi bootmgr loads the selected UEFI boot option.
This commit also provides the BOOT#### variable maintenance feature.
Depending on the system hardware setup, some devices
may not exist at a later system boot, so bootmenu checks the
available device in each bootmenu invocation and automatically
removes the BOOT#### variable corrensponding to the non-existent
media device.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Masahisa Kojima [Mon, 12 Sep 2022 08:33:53 +0000 (17:33 +0900)]
eficonfig: add "Delete Boot Option" menu entry
This commit adds the menu entry to delete the UEFI boot option.
User moves the entry with UP/DOWN key, changes, then presses
ENTER key to delete the selected boot option.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Masahisa Kojima [Mon, 12 Sep 2022 08:33:52 +0000 (17:33 +0900)]
menu: add KEY_PLUS, KEY_MINUS and KEY_SPACE handling
This is preparation to support menu-driven UEFI BootOrder
variable updated by KEY_PLUS, KEY_MINUS and KEY_SPACE.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Masahisa Kojima [Mon, 12 Sep 2022 08:33:51 +0000 (17:33 +0900)]
eficonfig: add "Edit Boot Option" menu entry
This commit adds the menu entry to edit the existing
BOOT#### variable contents.
User selects the item from the boot option list, then
user can edit the description, file path and optional_data.
Note that automatically generated boot option entry by bootmenu
to support the removable media device is filtered out and user
can not edit the automatically generated entry.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Masahisa Kojima [Mon, 12 Sep 2022 08:33:50 +0000 (17:33 +0900)]
eficonfig: menu-driven addition of UEFI boot option
This commit add the "eficonfig" command.
The "eficonfig" command implements the menu-driven UEFI boot option
maintenance feature. This commit implements the addition of
new boot option. User can select the block device volume having
efi_simple_file_system_protocol and select the file corresponding
to the Boot#### variable. User can also enter the description and
optional_data of the BOOT#### variable in utf8.
This commit adds "include/efi_config.h", it contains the common
definition to be used from other menus such as UEFI Secure Boot
key management.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Stefan Roese [Fri, 2 Sep 2022 11:57:54 +0000 (13:57 +0200)]
cyclic: Add a simple test
Add a test for cyclic function registration and activation.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Stefan Roese [Fri, 2 Sep 2022 11:57:53 +0000 (13:57 +0200)]
cyclic: Add documentation
Add documentation for the cyclic function infrastructure, including the
cyclic command.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Aaron Williams [Fri, 2 Sep 2022 11:57:52 +0000 (13:57 +0200)]
mips: octeon_nic23: Add PCIe FLR fixup via cyclic infrastructure
This patch adds a fixup function related to a PCIe FLR (Function Level
Reset) problem on the NIC23 PCIe board. This function is imported from
the Marvell Octeon 2013 U-Boot version as a (nearly) verbatim copy. It
uses the newly introduced cyclic infrastructure, so that this function
gets called every 100us, which is needed to detect this FLR issue.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Stefan Roese [Fri, 2 Sep 2022 11:57:51 +0000 (13:57 +0200)]
cyclic: Add 'cyclic list' and 'cyclic demo' commands
This patch adds the cyclic command, which currently only supports the
'list' subcommand, to list all currently registered cyclic functions.
Here an example:
=> cyclic list
function: cyclic_demo, cpu-time: 7010 us, frequency: 99.80 times/s
function: cyclic_demo2, cpu-time: 1 us, frequency: 1.13 times/s
As you can see, the cpu-time is accounted, so that cyclic functions
that take too long might be discovered. Additionally the frequency is
logged.
The 'cyclic demo' commands registers the cyclic_demo() function to
be executed all 'cycletime_ms' milliseconds. The only thing this
function does is delaying by 'delay_us' microseconds.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Stefan Roese [Fri, 2 Sep 2022 11:57:50 +0000 (13:57 +0200)]
cyclic: Integrate cyclic functionality at bootup in board_r/f
This patch adds a call to cyclic_init() to board_f/r.c, enabling the
common cyclic infrastructure. After this it's possible to add cyclic
functions via cyclic_register().
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Stefan Roese [Fri, 2 Sep 2022 11:57:49 +0000 (13:57 +0200)]
cyclic: Integrate cyclic infrastructure into WATCHDOG_RESET
This patch integrates the main function responsible for calling all
registered cyclic functions cyclic_run() into the common WATCHDOG_RESET
macro. This guarantees that cyclic_run() is executed very often, which
is necessary for the cyclic functions to get scheduled and executed at
their configured periods.
If CONFIG_WATCHDOG is not enabled, only cyclic_run() without calling
watchdog_reset(). This guarantees that the cyclic functionality does not
rely on CONFIG_WATCHDOG being enabled.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Stefan Roese [Fri, 2 Sep 2022 11:57:48 +0000 (13:57 +0200)]
cyclic: Add basic support for cyclic function execution infrastruture
Add the basic infrastructure to periodically execute code, e.g. all
100ms. Examples for such functions might be LED blinking etc. The
functions that are hooked into this cyclic list should be small timewise
as otherwise the execution of the other code that relies on a high
frequent polling (e.g. UART rx char ready check) might be delayed too
much. This patch also adds the Kconfig option
CONFIG_CYCLIC_MAX_CPU_TIME_US, which configures the max allowed time
for such a cyclic function. If it's execution time exceeds this time,
this cyclic function will get removed from the cyclic list.
How is this cyclic functionality executed?
The following patch integrates the main function responsible for
calling all registered cyclic functions cyclic_run() into the
common WATCHDOG_RESET macro. This guarantees that cyclic_run() is
executed very often, which is necessary for the cyclic functions to
get scheduled and executed at their configured periods.
This cyclic infrastructure will be used by a board specific function on
the NIC23 MIPS Octeon board, which needs to check periodically, if a
PCIe FLR has occurred.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Stefan Roese [Fri, 2 Sep 2022 11:57:47 +0000 (13:57 +0200)]
time: Import time_after64() and friends from Linux
When using us times it makes sense to use 64bit variables for storage.
The currently implemented time_after() and friends functions only handle
32bit variables. This patch now includes the 64bit variants as well
from Linux. This will be used by the upcoming generic cyclic function
infrastructure.
These macros were copied from include/linux/jiffies.h of Linux 5.18.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tom Rini [Tue, 13 Sep 2022 19:55:33 +0000 (15:55 -0400)]
Merge branch '2022-09-13-add-aspeed-spi-controller' into next
To quote the author:
This patch series aims to porting ASPEED FMC/SPI memory controller
driver with spi-mem interface. spi-mem dirmap framework is also
synchronized from Linux. These patches have been verified on
AST2600, AST2500 and AST2400 EVBs.
Chin-Ting Kuo [Fri, 19 Aug 2022 09:01:15 +0000 (17:01 +0800)]
mtd: spi-nor-ids: Add Winbond W25Q512JVQ ID
Add ID for Winbond W25Q512JVQ device which is supported
on AST2600 EVB by default.
Signed-off-by: Chin-Ting Kuo <chin-ting_kuo@aspeedtech.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Chin-Ting Kuo [Fri, 19 Aug 2022 09:01:14 +0000 (17:01 +0800)]
spi: aspeed: Clock frequency adjustment support
Driver can configure the SPI clock frequnecy to the
target value of "spi-max-frequency" property in
the device tree. The frequency is divided from HCLK,
200MHz. Usually, the ASPEED SPI clock frequency range
is between 12.5MHz and 100MHz. On AST2600, the lowest
SPI clock frequency can be about 780kHz.
Signed-off-by: Chin-Ting Kuo <chin-ting_kuo@aspeedtech.com>
Chin-Ting Kuo [Fri, 19 Aug 2022 09:01:13 +0000 (17:01 +0800)]
spi: aspeed: Support customized decoded address ranges
If "decoded-ranges" is defined in the device tree, the
driver will apply the decoded address ranges from this
property to the controller during probe stage.
This patch refers to the following OpenBMC u-boot patch.
https://patchwork.ozlabs.org/project/openbmc/list/?series=306969
Signed-off-by: Chin-Ting Kuo <chin-ting_kuo@aspeedtech.com>
Chin-Ting Kuo [Fri, 19 Aug 2022 09:01:12 +0000 (17:01 +0800)]
spi: aspeed: Adjust decoded range size support
There are some known HW problems about decoded
range register configurations on existing AST2500 and
AST2600 platforms. Additional callback function,
adjust_decoded_sz, is added to solve these problems
on each platform. Besides, aspeed_spi_trim_decoded_size
function is added to modify overall decoded address
size for fitting the maximum AHB decoded size.
Signed-off-by: Chin-Ting Kuo <chin-ting_kuo@aspeedtech.com>
Chin-Ting Kuo [Fri, 19 Aug 2022 09:01:11 +0000 (17:01 +0800)]
configs: aspeed: Enable CONFIG_SPI_DIRMAP
Enable CONFIG_SPI_DIRMAP on ASPEED platforms.
Signed-off-by: Chin-Ting Kuo <chin-ting_kuo@aspeedtech.com>
Chin-Ting Kuo [Fri, 19 Aug 2022 09:01:10 +0000 (17:01 +0800)]
spi: aspeed: SPI dirmap read support
From the HW point of view, the performance of
command read mode is greater than user mode slightly.
Thus, dirmap read framework is introduced to achieve
this goal. In dirmap_create, command read mode is
configured. Usually, the decoded address area with flash
size is assigned to each CS. CPU can thus access the
SPI flash as normal memory in dirmap_read function.
Signed-off-by: Chin-Ting Kuo <chin-ting_kuo@aspeedtech.com>
Chin-Ting Kuo [Fri, 19 Aug 2022 09:01:09 +0000 (17:01 +0800)]
mtd: spi-nor: Use spi-mem dirmap API
This adds support for the dirmap API to the spi-nor subsystem, as
introduced in Linux commit
df5c21002cf4 ("mtd: spi-nor: use
spi-mem dirmap API").
This patch is synchronize from the following patch
https://patchwork.ozlabs.org/project/uboot/patch/
20210205043924.149504-4-seanga2@gmail.com/
The corresponding Linux kernel SHA1 is
df5c21002cf4.
Signed-off-by: Chin-Ting Kuo <chin-ting_kuo@aspeedtech.com>
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Acked-by: Pratyush Yadav <p.yadav@ti.com>
Chin-Ting Kuo [Fri, 19 Aug 2022 09:01:08 +0000 (17:01 +0800)]
spi-mem: Add dirmap API from Linux
This adds the dirmap API originally introduced in
Linux commit
aa167f3fed0c
("spi: spi-mem: Add a new API to support direct mapping").
This also includes several follow-up patches and fixes.
Changes from Linux include:
* Added Kconfig option
* Changed struct device to struct udevice
* Changed struct spi_mem to struct spi_slave
This patch is obtained from the following patch
https://patchwork.ozlabs.org/project/uboot/patch/
20210205043924.149504-3-seanga2@gmail.com/
The corresponding Linux kernel SHA1 is
aa167f3fed0c.
Signed-off-by: Chin-Ting Kuo <chin-ting_kuo@aspeedtech.com>
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Acked-by: Pratyush Yadav <p.yadav@ti.com>
Chin-Ting Kuo [Fri, 19 Aug 2022 09:01:07 +0000 (17:01 +0800)]
arm: dts: aspeed: Update SPI flash node settings
For both AST2500 and AST2600, there are three
SPI controllers, FMC(Firmware Memory Controller),
SPI1 and SPI2. The clock source is HCLK. Following
is the basic information for ASPEED SPI controller.
AST2500:
- FMC:
CS number: 3
controller reg: 0x1e620000 - 0x1e62ffff
decoded address: 0x20000000 - 0x2fffffff
- SPI1:
CS number: 2
controller reg: 0x1e630000 - 0x1e630fff
decoded address: 0x30000000 - 0x37ffffff
- SPI2:
CS number: 2
controller reg: 0x1e631000 - 0x1e631fff
decoded address: 0x38000000 - 0x3fffffff
AST2600:
- FMC:
CS number: 3
controller reg: 0x1e620000 - 0x1e62ffff
decoded address: 0x20000000 - 0x2fffffff
- SPI1:
CS number: 2
controller reg: 0x1e630000 - 0x1e630fff
decoded address: 0x30000000 - 0x3fffffff
- SPI2:
CS number: 3
controller reg: 0x1e631000 - 0x1e631fff
decoded address: 0x50000000 - 0x5fffffff
Signed-off-by: Chin-Ting Kuo <chin-ting_kuo@aspeedtech.com>
Chin-Ting Kuo [Fri, 19 Aug 2022 09:01:06 +0000 (17:01 +0800)]
spi: aspeed: Support AST2400 platform
Although AST2400 is EOL officially, in order to achieve
sustainability and completeness, AST2400 part is added.
For AST2400,
- Five CSs are supported by FMC controller.
- SPI1 controller only supports single CS and there is
no address segment address register. The CE control
register of SPI1 is located at the offset 0x04 and
the 4-byte address mode control bit is bit 13 of
this register.
Signed-off-by: Chin-Ting Kuo <chin-ting_kuo@aspeedtech.com>
Chin-Ting Kuo [Fri, 19 Aug 2022 09:01:05 +0000 (17:01 +0800)]
configs: aspeed: Enable SPI flash features
- Enable ASPEED SPI controller driver.
- Enable SPI flash memory configurations.
- Enable configurations for SPI flash manufacturers
supported on both ASPEED AST2500 and AST2600 AVL.
Signed-off-by: Chin-Ting Kuo <chin-ting_kuo@aspeedtech.com>
Chin-Ting Kuo [Fri, 19 Aug 2022 09:01:04 +0000 (17:01 +0800)]
spi: aspeed: Add ASPEED SPI controller driver
Add ASPEED BMC FMC/SPI memory controller driver with
spi-mem interface for AST2500 and AST2600 platform.
There are three SPI memory controllers embedded in an ASPEED SoC.
- FMC: Named as Firmware Memory Controller. After AC on, MCU ROM
fetches initial device boot image from FMC chip select(CS) 0.
- SPI1: Play the role of a SPI Master controller. Or, there is a
dedicated path for HOST(X86) to access its BIOS flash mounted
under BMC. spi-aspeed-smc.c implements the control sequence when
SPI1 is a SPI master.
- SPI2: It is a pure SPI flash controller. For most scenarios, flashes
mounted under it are for pure storage purpose.
ASPEED SPI controller supports 1-1-1, 1-1-2 and 1-1-4 SPI flash mode.
Three types of command mode are supported, normal mode, command
read/write mode and user mode.
- Normal mode: Default mode. After power on, normal read command 03h or
13h is used to fetch boot image from SPI flash.
- AST2500: Only 03h command can be used after power on
or reset.
- AST2600: If FMC04[6:4] is set, 13h command is used,
otherwise, 03h command.
The address length is decided by FMC04[2:0].
- Command mode: SPI controller can send command and address
automatically when CPU read/write the related remapped
or decoded address area. The command used by this mode
can be configured by FMC10/14/18[23:16]. Also, the
address length is decided by FMC04[2:0]. This mode will
be implemented in the following patch series.
- User mode: It is a traditional and pure SPI operation, where
SPI transmission is controlled by CPU. It is the main
mode in this patch.
Each SPI controller in ASPEED SoC has its own decoded address mapping.
Within each SPI controller decoded address, driver can assign a specific
address region for each CS of a SPI controller. The decoded address
cannot overlap to each other. With normal mode and command mode, the
decoded address accessed by the CPU determines which CS is active.
When user mode is adopted, the CS decoded address is a FIFO, CPU can
send/receive any SPI transmission by accessing the related decoded
address for the target CS.
This patch only implements user mode initially. Command read/write
mode will be implemented in the following patches.
Signed-off-by: Chin-Ting Kuo <chin-ting_kuo@aspeedtech.com>
Chin-Ting Kuo [Fri, 19 Aug 2022 09:01:03 +0000 (17:01 +0800)]
pinctrl: aspeed: FWSPICS1 and SPI1CS1 pin support
Add FWSPICS1 and SPI1CS1 in AST2500 pinctrl group.
On AST2500 EVB, FWSPICS1 can be supported by default.
An extra jumper, J45, should be configured before
enabling SPI1CS1.
Signed-off-by: Chin-Ting Kuo <chin-ting_kuo@aspeedtech.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Chin-Ting Kuo [Fri, 19 Aug 2022 09:01:02 +0000 (17:01 +0800)]
clk: aspeed: Get HCLK frequency support
User can get correct HCLK frequency during driver probe stage
by adding the following configuration in the device tree.
"clocks = <&scu ASPEED_CLK_AHB>".
Signed-off-by: Chin-Ting Kuo <chin-ting_kuo@aspeedtech.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Tom Rini [Tue, 13 Sep 2022 13:34:12 +0000 (09:34 -0400)]
Merge tag 'xilinx-for-v2023.01-rc1' of https://source.denx.de/u-boot/custodians/u-boot-microblaze into next
Xilinx changes for v2023.01-rc1
cmd:
- bdinfo - guard LMB code to run only when LMB is enabled
timer:
- convert arm twd timer to DM
power-domain:
- Skip loading config object for Versal
xilinx:
- Fix logic when dfu_alt_info is generated
- Define only mmc devnum not partition
- Add xlnx prefix to GEM compatible string
- Add missing tca6416 to zynqmp SC - vck190
- Add env redund offset
- Enable CMD_GREPENV/SETEXPR by default
- Move board_get_usable_ram_top() to common location
- Add support for SOC detection
net/gem:
- Check rate before setting it up
microblaze:
- drop CONFIG_SYS_INIT_RAM_ADDR and CONFIG_SYS_INIT_RAM_SIZE
- Show cache size in bdinfo
spi:
- cadence_qspi: driver updates
- zynqmp_gqspi: driver updates
- zynqmp_gqspi: Add tap delays for Versal
zynq:
- Enable mkeficapsule compilation
- Use CONFIG_SPL_FS_LOAD_PAYLOAD_NAME for dfu_alt_info
- Align bss and end of u-boot image to 64bits
- Align qspi node name with Linux kernel
- DT: List OCM memory
zynqmp:
- Fix AES cache handling with a user provided key
- SOM: Add mtd partition for secure OS storage area
- Add ref_clk property for REFCLKPER calculation
- Fix mdio bus description for vck190-sc
xilinx-mini:
- Remove unneeded configs
- Disable LMB
versal:
- Enable i2c mux pca954x by default
- Define CONFIG_CQSPI_REF_CLK
- Enable power domain driver
- Enable zynqmp_gqspi driver
Tom Rini [Tue, 13 Sep 2022 12:59:11 +0000 (08:59 -0400)]
Merge branch '2022-09-12-update-pytests-for-more-parellel-support' into next
To quote the author:
This series makes a further attempt to get closer to having all tests
run in parallel. It introduces a new 'make pcheck' option which runs
tests in parallel, skipping those that are not compatible.
A number of fixes are included for existing tests. The vboot test is
updated to only run a single scenario in 'quick' mode.
This makes use of pytest's parallel-testing features. The resulting
times (including incremental building with LTO) on a 16-core machine are
as follows:
make pcheck - 1 minute 6 seconds
make qcheck - 3 minutes
make check - 5 minutes 15 seconds
Note that this is not a fair comparison, since 'make pcheck' omits a
number of tests, even more than 'make qcheck'.
Michal Simek [Tue, 6 Sep 2022 10:40:41 +0000 (12:40 +0200)]
xilinx: common: Add support for SOC detection
Code supports board detection based on information available in EEPROM in
legacy or FRU format. But this is not enough for emulation and simulation
systems which are lacking these identification EEPROMs. But SOC itself has
normally registers for SOC identification. Based on them it is possible to
compose detected name. That's why prepare infrastructure in common location
for SOC platform detection which is called before board platform detection.
SOC platform detection shouldn't detect real silicon and should fallback to
current existing mechanism to identify boards based on EEPROMs.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/329a8da338927b082e26a958bf69bb18af072420.1662460837.git.michal.simek@amd.com
Michal Simek [Tue, 6 Sep 2022 10:39:11 +0000 (12:39 +0200)]
xilinx: Fix mdio bus description for vck190-sc
Current behavior is that eth_phy_get_mdio_bus
Net: FEC: can't find phy-handle
ZYNQ GEM:
ff0b0000, mdio bus
ff0b0000, phyaddr 0, interface sgmii
eth0: ethernet@
ff0b0000
Net:
ZYNQ GEM:
ff0b0000, mdio bus
ff0b0000, phyaddr 0, interface sgmii
eth0: ethernet@
ff0b0000
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/5b7da5808136b3f579c0cf7a3431b56c758655e9.1662460749.git.michal.simek@amd.com
Michal Simek [Tue, 6 Sep 2022 10:38:34 +0000 (12:38 +0200)]
ARM: zynq: DT: List OCM memory
Description OCM with mmio-sram driver. In 99% use cases OCM is mapped high
that's why it is placed on fixed location.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/a951dbe885640197efe3e91bb9fa5caedb54b387.1662460712.git.michal.simek@amd.com
Michal Simek [Tue, 6 Sep 2022 10:35:42 +0000 (12:35 +0200)]
ARM: zynq: Align qspi node name with Linux kernel
Nodes should follow generic rules where compatible and reg properties
should be listed on the top of node. That's why sync it up.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/922dca6227cb0aa4f79e6d3595c5f280ba020684.1662460540.git.michal.simek@amd.com
Ashok Reddy Soma [Thu, 25 Aug 2022 12:59:06 +0000 (06:59 -0600)]
arm64: versal: Enable zynqmp_gqspi driver
Versal supports gqspi ip, so enable zynqmp_gqspi driver for Versal
platforms.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20220825125906.11581-7-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Ashok Reddy Soma [Thu, 25 Aug 2022 12:59:05 +0000 (06:59 -0600)]
spi: zynqmp_qspi: Code alignment
Few lines are extented to next line though they can fit in 80 character
limit, align them to single line. No functional change.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20220825125906.11581-6-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Ashok Reddy Soma [Thu, 25 Aug 2022 12:59:04 +0000 (06:59 -0600)]
spi: zynqmp_gqspi: Fix issue of reading more than 32bits length
As the flash sizes are increasing day by day, QSPI can have devices of
size > 512MB. In qspi driver we are trying to read all the data at once
using DMA.
The DMA descriptor destination size is only 29bits long.
QSPIDMA_DST_SIZE 0xFF0F0804
BITS: 1:0 Reserved to keep word alignment
BITS: 28:2 Number of 4-byte words the DMA will transfer
BITS: 31:29 Reserved: Returns 0 when read, writes ignored
So we can only transfer data of 0x1FFFFFF0(512MB minus 4bytes) bytes.
Anything above will overflow this register and will ignore higher bits
above 29 bits.
Change the DMA functionality if the requested size is greater than or
equal to 512MB to read 256MB chunks.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20220825125906.11581-5-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Ashok Reddy Soma [Thu, 25 Aug 2022 12:59:03 +0000 (06:59 -0600)]
spi: zynqmp_gqspi: Add support for IO mode
Add support for io-mode transfers. This is necessary for UBIFS to work
properly with spi-nor devices. The driver will work in IO mode when
"has-io-mode" is passed from device tree instead of DMA.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20220825125906.11581-4-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Michal Simek [Thu, 25 Aug 2022 12:59:02 +0000 (06:59 -0600)]
arm64: versal: Define zynqmp_mmio_write() for versal
GQSPI driver is using it but this function is never called for Versal
because it is removed by linker. But function should be declared to avoid
this build warning:
drivers/spi/zynqmp_gqspi.c: In function 'zynqmp_qspi_set_tapdelay':
drivers/spi/zynqmp_gqspi.c:378:3: warning: implicit declaration of function
'zynqmp_mmio_write' [-Wimplicit-function-declaration]
378 | zynqmp_mmio_write(IOU_TAPDLY_BYPASS_OFST,
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20220825125906.11581-3-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Ashok Reddy Soma [Thu, 25 Aug 2022 12:59:01 +0000 (06:59 -0600)]
spi: zynqmp_gqspi: Add tap delays for Versal
Add tap delays for Versal platform and re-align the tapdelays code.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20220825125906.11581-2-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Ashok Reddy Soma [Wed, 24 Aug 2022 11:38:47 +0000 (05:38 -0600)]
spi: cadence-qspi: Use priv instead of plat across the driver
As per driver model we should enumerate plat structure only in
of_to_plat() and should be used only in probe(). Copy required
plat structure info into priv structure in probe() and use priv
structure across the driver. So replace plat with priv structure across
the driver.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Link: https://lore.kernel.org/r/20220824113847.7482-4-ashok.reddy.soma@xilinx.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Ashok Reddy Soma [Wed, 24 Aug 2022 11:38:46 +0000 (05:38 -0600)]
spi: cadence_qspi: Call read_setup for STIG_READ
In cadence_spi_read_id we are using STIG mode to read flash id's.
Call cadence_qspi_apb_command_read_setup() to setup cmd, addr and data
bus width properly before cadence_qspi_apb_command_read().
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Link: https://lore.kernel.org/r/20220824113847.7482-3-ashok.reddy.soma@xilinx.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Ashok Reddy Soma [Wed, 24 Aug 2022 11:38:45 +0000 (05:38 -0600)]
spi: cadence-qspi: Correct flash reset function name
In cadence_spi_probe, cadence_qspi_versal_flash_reset() is called to reset
the flash device. Looks like there is a mistake in previous series of
patches where it is defined as cadence_spi_versal_flash_reset() but
called as cadence_qspi_versal_flash_reset. Since there is a weak function
defined with the same name this issue was not caught.
Fix the issue by renaming cadence_spi_versal_flash_reset as
cadence_qspi_versal_flash_reset().
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Link: https://lore.kernel.org/r/20220824113847.7482-2-ashok.reddy.soma@xilinx.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Ovidiu Panait [Mon, 29 Aug 2022 17:02:05 +0000 (20:02 +0300)]
microblaze: add arch_print_bdinfo() implementation
Allow bdinfo command to print icache/dcache information:
U-Boot-mONStR> bdinfo
boot_params = 0x00000000
DRAM bank = 0x00000000
-> start = 0x04000000
-> size = 0x04000000
flashstart = 0x00000000
flashsize = 0x00000000
flashoffset = 0x00000000
baudrate = 9600 bps
relocaddr = 0x07f76000
reloc off = 0x02f76000
Build = 32-bit
current eth = unknown
ethaddr = (not set)
IP addr = <NULL>
fdt_blob = 0x07fec7e0
new_fdt = 0x00000000
fdt_size = 0x00000000
lmb_dump_all:
memory.cnt = 0x1
memory[0] [0x4000000-0x7ffffff], 0x04000000 bytes flags: 0
reserved.cnt = 0x1
reserved[0] [0x7e94b8c-0x7ffffff], 0x0016b474 bytes flags: 0
devicetree = embed
icache = 32 KiB
icache line = 4 Bytes
dcache = 32 KiB
dcache line = 4 Bytes
Signed-off-by: Ovidiu Panait <ovpanait@gmail.com>
Link: https://lore.kernel.org/r/20220829170205.1274484-4-ovpanait@gmail.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Ovidiu Panait [Mon, 29 Aug 2022 17:02:04 +0000 (20:02 +0300)]
cmd: bdinfo: introduce bdinfo_print_size() helper
Add bdinfo_print_size() helper to display size variables (such as cache
sizes) in bdinfo format. The size is printed as "xxx Bytes", "xxx KiB",
"xxx MiB", "xxx GiB", etc as needed;
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Ovidiu Panait <ovpanait@gmail.com>
Reviewed-by: Jason Liu <jason.hui.liu@nxp.com>
Link: https://lore.kernel.org/r/20220829170205.1274484-3-ovpanait@gmail.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Ovidiu Panait [Mon, 29 Aug 2022 17:02:03 +0000 (20:02 +0300)]
cpu: microblaze: add error handling in microblaze_cpu_get_desc()
Check snprintf() return value for errors.
Make microblaze_cpu_get_desc() directly return snprintf() error code if
ret < 0. Otherwise, if the return value is greater than or equal to size,
the resulting string is truncated, so return -ENOSPC.
Fixes:
816226d27e ("cpu: add CPU driver for microblaze")
Signed-off-by: Ovidiu Panait <ovpanait@gmail.com>
Link: https://lore.kernel.org/r/20220829170205.1274484-2-ovpanait@gmail.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Ovidiu Panait [Mon, 29 Aug 2022 17:02:02 +0000 (20:02 +0300)]
microblaze: drop CONFIG_SYS_INIT_RAM_ADDR and CONFIG_SYS_INIT_RAM_SIZE
These macros are not used anymore in microblaze code since commit
f113d7d303467 ("Convert CONFIG_SPL_STACK to Kconfig"), so remove them.
Fixes:
f113d7d303467 ("Convert CONFIG_SPL_STACK to Kconfig")
Signed-off-by: Ovidiu Panait <ovpanait@gmail.com>
Link: https://lore.kernel.org/r/20220829170205.1274484-1-ovpanait@gmail.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Michal Simek [Fri, 26 Aug 2022 08:30:47 +0000 (10:30 +0200)]
net: gem: Check rate before setting it up
On QEMU setting rate for fixed clock is failing. That's why check a rate
first if the rate is the same there is no need to ask for the change.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/bc465ffd4904bfd65208b782daa06732b915db54.1661502645.git.michal.simek@amd.com
Michal Simek [Tue, 6 Sep 2022 10:41:34 +0000 (12:41 +0200)]
xilinx: versal: Disable LMB for mini configurations
There shouldn't be a reason to have LMB on for these configurations.
LMB was already disabled for ZynqMP by commit
0063487a5b60 ("configs:
zynqmp: Disable LMB for mini u-boot").
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/17d1e9b50b2fd032352911f94f4f213828e0a3f7.1662460892.git.michal.simek@amd.com
Michal Simek [Thu, 25 Aug 2022 12:23:10 +0000 (14:23 +0200)]
arm64: xilinx: Move board_get_usable_ram_top() to common location
The commit
ce39ee28ec31 ("zynqmp: Do not place u-boot to reserved memory
location") adds functionality for ZynqMP to read reserved memory node and
do not place U-Boot to reserved location. This functionality is generic
across all Xilinx SOCs that's why move it to common location to be used by
all Xilinx SOCs.
On zynq platform this is also fixing issue where U-Boot was placed to
locating which was reserved already which ends up with error message
"ERROR: reserving fdt memory region failed (addr=
30000000 size=
10000000
flags=4)" which is shown when bdinfo is called.
Tested on vck190, zcu102, zc706 and kc705 to cover all platforms.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/b0817807912f7c7af6a8e1cf9ee04e5ab5de5f6a.1661430188.git.michal.simek@amd.com