Tomasz Moń [Tue, 1 Mar 2022 06:03:31 +0000 (07:03 +0100)]
sc16is7xx: Handle modem status lines
The uart_handle_cts_change() and uart_handle_dcd_change() must be called
with port lock being held. Acquire the lock after reading MSR register.
Do not acquire spin lock when reading MSR register because I2C/SPI port
functions cannot be called with spinlocks held.
Update rng and dsr counters. Wake up delta_msr_wait to allow tty notice
modem status change.
Co-developed-by: Lech Perczak <l.perczak@camlintechnologies.com>
Co-developed-by: Tomasz Moń <tomasz.mon@camlingroup.com>
Signed-off-by: Lech Perczak <l.perczak@camlintechnologies.com>
Signed-off-by: Tomasz Moń <tomasz.mon@camlingroup.com>
Link: https://lore.kernel.org/r/20220301060332.2561851-3-tomasz.mon@camlingroup.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tomasz Moń [Tue, 1 Mar 2022 06:03:30 +0000 (07:03 +0100)]
sc16is7xx: Properly resume TX after stop
sc16is7xx_stop_tx() clears THRI bit and thus disables THRI interrupt.
This makes it possible for transmission to cease indefinitely when more
than 64 characters are being sent.
The sc16is7xx_handle_tx() call executed by sc16is7xx_tx_proc() can send
up to FIFO length (64) characters. If more characters are written to the
output buffer, then the THRI interrupt is needed.
Solve the issue by enabling THRI interrupt in sc16is7xx_tx_proc().
Signed-off-by: Tomasz Moń <tomasz.mon@camlingroup.com>
Link: https://lore.kernel.org/r/20220301060332.2561851-2-tomasz.mon@camlingroup.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Greg Kroah-Hartman [Tue, 1 Mar 2022 21:06:50 +0000 (22:06 +0100)]
Revert "tty: serial: meson: *"
This reverts the following commits:
31979060cc07 tty: serial: meson: Fix the compile link error reported by kernel test robot
5427c352a993 tty: serial: meson: Added S4 SOC compatibility
19b2ba0baffc tty: serial: meson: The system stuck when you run the stty command on the console to change the baud rate
e5fc2b99840d tty: serial: meson: Make some bit of the REG5 register writable
44023b8e1f14 tty: serial: meson: Describes the calculation of the UART baud rate clock using a clock frame
6436dd8f9b25 tty: serial: meson: Use devm_ioremap_resource to get register mapped memory
841f913e770f tty: serial: meson: Move request the register region to probe
They seem to cause lots of problems with existing hardware platforms,
and caused build issues, so revert the whole series all at once.
Link: https://lore.kernel.org/r/849a95fd-ae81-9a3b-0c06-dd7826af9eb2@baylibre.com
Link: https://lore.kernel.org/all/20220225073922.3947-1-yu.tu@amlogic.com/
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reported-by: Jerome Brunet <jbrunet@baylibre.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Yu Tu <yu.tu@amlogic.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hammer Hsieh [Tue, 1 Mar 2022 04:19:46 +0000 (12:19 +0800)]
serial: sunplus-uart: Fix compile error while CONFIG_SERIAL_SUNPLUS_CONSOLE=n
1. Fix implicit declaration of function 'wait_for_xmitr' issue.
2. Fix 'sunplus_uart_console' undeclared here issue.
3. Fix use of undeclared identifier 'sunplus_uart_console' issue.
Fixes:
9e8d5470325f ("serial: sunplus-uart: Add Sunplus SoC UART Driver")
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kernel test robot <lkp@intel.com>
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Hammer Hsieh <hammerh0314@gmail.com>
Link: https://lore.kernel.org/r/1646108386-29905-1-git-send-email-hammerh0314@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Yu Tu [Mon, 28 Feb 2022 06:49:10 +0000 (14:49 +0800)]
tty: serial: meson: Fix the compile link error reported by kernel test robot
Describes the calculation of the UART baud rate clock using a clock
frame. Forgot to add in Kconfig kernel test Robot compilation error
due to COMMON_CLK dependency.
Fixes:
44023b8e1f14 ("tty: serial: meson: Describes the calculation of the UART baud rate clock using a clock frame")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Yu Tu <yu.tu@amlogic.com>
Link: https://lore.kernel.org/r/20220228064910.11636-1-yu.tu@amlogic.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jiri Slaby [Thu, 24 Feb 2022 09:55:58 +0000 (10:55 +0100)]
mxser: make use of UART_LCR_WLEN() + tty_get_char_size()
Having a generic UART_LCR_WLEN() macro and the tty_get_char_size()
helper, we can remove all those repeated switch-cases in drivers.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220224095558.30929-5-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jiri Slaby [Thu, 24 Feb 2022 09:55:57 +0000 (10:55 +0100)]
sdio_uart: make use of UART_LCR_WLEN() + tty_get_char_size()
Having a generic UART_LCR_WLEN() macro and the tty_get_char_size()
helper, we can remove all those repeated switch-cases in drivers.
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: linux-mmc@vger.kernel.org
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220224095558.30929-4-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jiri Slaby [Thu, 24 Feb 2022 09:55:56 +0000 (10:55 +0100)]
USB: serial: make use of UART_LCR_WLEN() + tty_get_char_size()
Having a generic UART_LCR_WLEN() macro and the tty_get_char_size()
helper, we can remove all those repeated switch-cases in drivers.
Cc: Johan Hovold <johan@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220224095558.30929-3-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jiri Slaby [Thu, 24 Feb 2022 09:55:55 +0000 (10:55 +0100)]
tty: serial: make use of UART_LCR_WLEN() + tty_get_char_size()
Having a generic UART_LCR_WLEN() macro and the tty_get_char_size()
helper, we can remove all those repeated switch-cases in drivers.
Cc: Laxman Dewangan <ldewangan@nvidia.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: linux-tegra@vger.kernel.org
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220224095558.30929-2-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jiri Slaby [Thu, 24 Feb 2022 09:55:54 +0000 (10:55 +0100)]
tty: serial: define UART_LCR_WLEN() macro
Define a generic UART_LCR_WLEN() macro with a size argument. It can be
used to encode byte size into an LCR value. Therefore we can use it to
simplify the drivers using tty_get_char_size() in the next patches.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220224095558.30929-1-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Greg Kroah-Hartman [Mon, 28 Feb 2022 20:48:16 +0000 (21:48 +0100)]
Merge 5.17-rc6 into tty-next
We need the tty/serial fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Linus Torvalds [Sun, 27 Feb 2022 22:36:33 +0000 (14:36 -0800)]
Linux 5.17-rc6
Linus Torvalds [Sun, 27 Feb 2022 21:07:40 +0000 (13:07 -0800)]
Merge tag 'irq-urgent-2022-02-27' of git://git./linux/kernel/git/tip/tip
Pull irq fix from Thomas Gleixner:
"A single fix for a regression caused by the recent PCI/MSI rework
which resulted in a recursive locking problem in the VMD driver.
The cure is to cache the relevant information upfront instead of
retrieving it at runtime"
* tag 'irq-urgent-2022-02-27' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
PCI: vmd: Prevent recursive locking on interrupt allocation
Linus Torvalds [Sun, 27 Feb 2022 20:42:37 +0000 (12:42 -0800)]
Merge tag 'dma-mapping-5.17-1' of git://git.infradead.org/users/hch/dma-mapping
Pull dma-mapping fix from Christoph Hellwig:
- fix a swiotlb info leak (Halil Pasic)
* tag 'dma-mapping-5.17-1' of git://git.infradead.org/users/hch/dma-mapping:
swiotlb: fix info leak with DMA_FROM_DEVICE
Linus Torvalds [Sun, 27 Feb 2022 20:30:54 +0000 (12:30 -0800)]
Merge tag 'pinctrl-v5-17-3' of git://git./linux/kernel/git/linusw/linux-pinctrl
Pull pin control fixes from Linus Walleij:
- Fix some drive strength and pull-up code in the K210 driver.
- Add the Alder Lake-M ACPI ID so it starts to work properly.
- Use a static name for the StarFive GPIO irq_chip, forestalling an
upcoming fixes series from Marc Zyngier.
- Fix an ages old bug in the Tegra 186 driver where we were indexing at
random into struct and being lucky getting the right member.
* tag 'pinctrl-v5-17-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
gpio: tegra186: Fix chip_data type confusion
pinctrl: starfive: Use a static name for the GPIO irq_chip
pinctrl: tigerlake: Revert "Add Alder Lake-M ACPI ID"
pinctrl: k210: Fix bias-pull-up
pinctrl: fix loop in k210_pinconf_get_drive()
Linus Torvalds [Sat, 26 Feb 2022 20:10:17 +0000 (12:10 -0800)]
Merge tag 'trace-v5.17-rc4' of git://git./linux/kernel/git/rostedt/linux-trace
Pull tracing fixes from Steven Rostedt:
- rtla (Real-Time Linux Analysis tool):
- fix typo in man page
- Update API -e to -E before it is released
- Error message fix and memory leak fix
- Partially uninline trace event soft disable to shrink text
- Fix function graph start up test
- Have triggers affect the trace instance they are in and not top level
- Have osnoise sleep in the units it says it uses
- Remove unused ftrace stub function
- Remove event probe redundant info from event in the buffer
- Fix group ownership setting in tracefs
- Ensure trace buffer is minimum size to prevent crashes
* tag 'trace-v5.17-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
rtla/osnoise: Fix error message when failing to enable trace instance
rtla/osnoise: Free params at the exit
rtla/hist: Make -E the short version of --entries
tracing: Fix selftest config check for function graph start up test
tracefs: Set the group ownership in apply_options() not parse_options()
tracing/osnoise: Make osnoise_main to sleep for microseconds
ftrace: Remove unused ftrace_startup_enable() stub
tracing: Ensure trace buffer is at least 4096 bytes large
tracing: Uninline trace_trigger_soft_disabled() partly
eprobes: Remove redundant event type information
tracing: Have traceon and traceoff trigger honor the instance
tracing: Dump stacktrace trigger to the corresponding instance
rtla: Fix systme -> system typo on man page
Linus Torvalds [Sat, 26 Feb 2022 20:00:44 +0000 (12:00 -0800)]
Merge tag 'fixes-2022-02-26' of git://git./linux/kernel/git/rppt/memblock
Pull memblock fix from Mike Rapoport:
"Use kfree() to release kmalloced memblock regions
memblock.{reserved,memory}.regions may be allocated using kmalloc()
in memblock_double_array(). Use kfree() to release these kmalloced
regions"
* tag 'fixes-2022-02-26' of git://git.kernel.org/pub/scm/linux/kernel/git/rppt/memblock:
memblock: use kfree() to release kmalloced memblock regions
Linus Torvalds [Sat, 26 Feb 2022 19:52:14 +0000 (11:52 -0800)]
Merge branch 'akpm' (patches from Andrew)
Merge misc fixes from Andrew Morton:
"12 patches.
Subsystems affected by this patch series: MAINTAINERS, mailmap, memfd,
and mm (hugetlb, kasan, hugetlbfs, pagemap, selftests, memcg, and
slab)"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
selftests/memfd: clean up mapping in mfd_fail_write
mailmap: update Roman Gushchin's email
MAINTAINERS, SLAB: add Roman as reviewer, git tree
MAINTAINERS: add Shakeel as a memcg co-maintainer
MAINTAINERS: remove Vladimir from memcg maintainers
MAINTAINERS: add Roman as a memcg co-maintainer
selftest/vm: fix map_fixed_noreplace test failure
mm: fix use-after-free bug when mm->mmap is reused after being freed
hugetlbfs: fix a truncation issue in hugepages parameter
kasan: test: prevent cache merging in kmem_cache_double_destroy
mm/hugetlb: fix kernel crash with hugetlb mremap
MAINTAINERS: add sysctl-next git tree
Linus Torvalds [Sat, 26 Feb 2022 18:26:24 +0000 (10:26 -0800)]
Merge tag 'riscv-for-linus-5.17-rc6' of git://git./linux/kernel/git/riscv/linux
Pull RISC-V fixes from Palmer Dabbelt:
- A fix for the K210 sdcard defconfig, to avoid using a
fixed delay for the root FS
- A fix to make sure there's a proper call frame for
trace_hardirqs_{on,off}().
* tag 'riscv-for-linus-5.17-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
riscv: fix oops caused by irqsoff latency tracer
riscv: fix nommu_k210_sdcard_defconfig
Linus Torvalds [Sat, 26 Feb 2022 17:53:19 +0000 (09:53 -0800)]
Merge tag 'xfs-5.17-fixes-2' of git://git./fs/xfs/xfs-linux
Pull xfs fixes from Darrick Wong:
"Nothing exciting, just more fixes for not returning sync_filesystem
error values (and eliding it when it's not necessary).
Summary:
- Only call sync_filesystem when we're remounting the filesystem
readonly readonly, and actually check its return value"
* tag 'xfs-5.17-fixes-2' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
xfs: only bother with sync_filesystem during readonly remount
Mike Kravetz [Sat, 26 Feb 2022 03:11:26 +0000 (19:11 -0800)]
selftests/memfd: clean up mapping in mfd_fail_write
Running the memfd script ./run_hugetlbfs_test.sh will often end in error
as follows:
memfd-hugetlb: CREATE
memfd-hugetlb: BASIC
memfd-hugetlb: SEAL-WRITE
memfd-hugetlb: SEAL-FUTURE-WRITE
memfd-hugetlb: SEAL-SHRINK
fallocate(ALLOC) failed: No space left on device
./run_hugetlbfs_test.sh: line 60: 166855 Aborted (core dumped) ./memfd_test hugetlbfs
opening: ./mnt/memfd
fuse: DONE
If no hugetlb pages have been preallocated, run_hugetlbfs_test.sh will
allocate 'just enough' pages to run the test. In the SEAL-FUTURE-WRITE
test the mfd_fail_write routine maps the file, but does not unmap. As a
result, two hugetlb pages remain reserved for the mapping. When the
fallocate call in the SEAL-SHRINK test attempts allocate all hugetlb
pages, it is short by the two reserved pages.
Fix by making sure to unmap in mfd_fail_write.
Link: https://lkml.kernel.org/r/20220219004340.56478-1-mike.kravetz@oracle.com
Signed-off-by: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Joel Fernandes <joel@joelfernandes.org>
Cc: Shuah Khan <shuah@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Roman Gushchin [Sat, 26 Feb 2022 03:11:23 +0000 (19:11 -0800)]
mailmap: update Roman Gushchin's email
I'm moving to a @linux.dev account. Map my old addresses.
Link: https://lkml.kernel.org/r/20220221200006.416377-1-roman.gushchin@linux.dev
Signed-off-by: Roman Gushchin <roman.gushchin@linux.dev>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Vlastimil Babka [Sat, 26 Feb 2022 03:11:20 +0000 (19:11 -0800)]
MAINTAINERS, SLAB: add Roman as reviewer, git tree
The slab code has an overlap with kmem accounting, where Roman has done
a lot of work recently and it would be useful to make sure he's CC'd on
patches that potentially affect it. Thus add him as a reviewer for the
SLAB subsystem.
Also while at it, add the link to slab git tree.
Link: https://lkml.kernel.org/r/20220222103104.13241-1-vbabka@suse.cz
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Acked-by: David Rientjes <rientjes@google.com>
Acked-by: Roman Gushchin <roman.gushchin@linux.dev>
Cc: Christoph Lameter <cl@linux.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Shakeel Butt [Sat, 26 Feb 2022 03:11:17 +0000 (19:11 -0800)]
MAINTAINERS: add Shakeel as a memcg co-maintainer
I have been contributing and reviewing to the memcg codebase for last
couple of years. So, making it official.
Link: https://lkml.kernel.org/r/20220224060148.4092228-1-shakeelb@google.com
Signed-off-by: Shakeel Butt <shakeelb@google.com>
Acked-by: Roman Gushchin <roman.gushchin@linux.dev>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Vladimir Davydov [Sat, 26 Feb 2022 03:11:14 +0000 (19:11 -0800)]
MAINTAINERS: remove Vladimir from memcg maintainers
Link: https://lkml.kernel.org/r/4ad1f8da49d7b71c84a0c15bd5347f5ce704e730.1645608825.git.vdavydov.dev@gmail.com
Signed-off-by: Vladimir Davydov <vdavydov.dev@gmail.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Roman Gushchin <roman.gushchin@linux.dev>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Roman Gushchin [Sat, 26 Feb 2022 03:11:11 +0000 (19:11 -0800)]
MAINTAINERS: add Roman as a memcg co-maintainer
Add myself as a memcg co-maintainer. My primary focus over last few
years was the kernel memory accounting stack, but I do work on some
other parts of the memory controller as well.
Link: https://lkml.kernel.org/r/20220221233951.659048-1-roman.gushchin@linux.dev
Signed-off-by: Roman Gushchin <roman.gushchin@linux.dev>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Vladimir Davydov <vdavydov.dev@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Aneesh Kumar K.V [Sat, 26 Feb 2022 03:11:08 +0000 (19:11 -0800)]
selftest/vm: fix map_fixed_noreplace test failure
On the latest RHEL the test fails due to executable mapped at 256MB
address
# ./map_fixed_noreplace
mmap() @ 0x10000000-0x10050000 p=0xffffffffffffffff result=File exists
10000000-
10010000 r-xp
00000000 fd:04
34905657 /root/rpmbuild/BUILD/kernel-5.14.0-56.el9/linux-5.14.0-56.el9.ppc64le/tools/testing/selftests/vm/map_fixed_noreplace
10010000-
10020000 r--p
00000000 fd:04
34905657 /root/rpmbuild/BUILD/kernel-5.14.0-56.el9/linux-5.14.0-56.el9.ppc64le/tools/testing/selftests/vm/map_fixed_noreplace
10020000-
10030000 rw-p
00010000 fd:04
34905657 /root/rpmbuild/BUILD/kernel-5.14.0-56.el9/linux-5.14.0-56.el9.ppc64le/tools/testing/selftests/vm/map_fixed_noreplace
10029b90000-
10029bc0000 rw-p
00000000 00:00 0 [heap]
7fffbb510000-
7fffbb750000 r-xp
00000000 fd:04 24534 /usr/lib64/libc.so.6
7fffbb750000-
7fffbb760000 r--p
00230000 fd:04 24534 /usr/lib64/libc.so.6
7fffbb760000-
7fffbb770000 rw-p
00240000 fd:04 24534 /usr/lib64/libc.so.6
7fffbb780000-
7fffbb7a0000 r--p
00000000 00:00 0 [vvar]
7fffbb7a0000-
7fffbb7b0000 r-xp
00000000 00:00 0 [vdso]
7fffbb7b0000-
7fffbb800000 r-xp
00000000 fd:04 24514 /usr/lib64/ld64.so.2
7fffbb800000-
7fffbb810000 r--p
00040000 fd:04 24514 /usr/lib64/ld64.so.2
7fffbb810000-
7fffbb820000 rw-p
00050000 fd:04 24514 /usr/lib64/ld64.so.2
7fffd93f0000-
7fffd9420000 rw-p
00000000 00:00 0 [stack]
Error: couldn't map the space we need for the test
Fix this by finding a free address using mmap instead of hardcoding
BASE_ADDRESS.
Link: https://lkml.kernel.org/r/20220217083417.373823-1-aneesh.kumar@linux.ibm.com
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Jann Horn <jannh@google.com>
Cc: Shuah Khan <shuah@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Suren Baghdasaryan [Sat, 26 Feb 2022 03:11:05 +0000 (19:11 -0800)]
mm: fix use-after-free bug when mm->mmap is reused after being freed
oom reaping (__oom_reap_task_mm) relies on a 2 way synchronization with
exit_mmap. First it relies on the mmap_lock to exclude from unlock
path[1], page tables tear down (free_pgtables) and vma destruction.
This alone is not sufficient because mm->mmap is never reset.
For historical reasons[2] the lock is taken there is also MMF_OOM_SKIP
set for oom victims before.
The oom reaper only ever looks at oom victims so the whole scheme works
properly but process_mrelease can opearate on any task (with fatal
signals pending) which doesn't really imply oom victims. That means
that the MMF_OOM_SKIP part of the synchronization doesn't work and it
can see a task after the whole address space has been demolished and
traverse an already released mm->mmap list. This leads to use after
free as properly caught up by KASAN report.
Fix the issue by reseting mm->mmap so that MMF_OOM_SKIP synchronization
is not needed anymore. The MMF_OOM_SKIP is not removed from exit_mmap
yet but it acts mostly as an optimization now.
[1]
27ae357fa82b ("mm, oom: fix concurrent munlock and oom reaper unmap, v3")
[2]
212925802454 ("mm: oom: let oom_reap_task and exit_mmap run concurrently")
[mhocko@suse.com: changelog rewrite]
Link: https://lore.kernel.org/all/00000000000072ef2c05d7f81950@google.com/
Link: https://lkml.kernel.org/r/20220215201922.1908156-1-surenb@google.com
Fixes:
64591e8605d6 ("mm: protect free_pgtables with mmap_lock write lock in exit_mmap")
Signed-off-by: Suren Baghdasaryan <surenb@google.com>
Reported-by: syzbot+2ccf63a4bd07cf39cab0@syzkaller.appspotmail.com
Suggested-by: Michal Hocko <mhocko@suse.com>
Reviewed-by: Rik van Riel <riel@surriel.com>
Reviewed-by: Yang Shi <shy828301@gmail.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Roman Gushchin <roman.gushchin@linux.dev>
Cc: Rik van Riel <riel@surriel.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Kirill A. Shutemov <kirill@shutemov.name>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Christian Brauner <brauner@kernel.org>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: David Hildenbrand <david@redhat.com>
Cc: Jann Horn <jannh@google.com>
Cc: Shakeel Butt <shakeelb@google.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Christian Brauner <christian.brauner@ubuntu.com>
Cc: Florian Weimer <fweimer@redhat.com>
Cc: Jan Engelhardt <jengelh@inai.de>
Cc: Tim Murray <timmurray@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Liu Yuntao [Sat, 26 Feb 2022 03:11:02 +0000 (19:11 -0800)]
hugetlbfs: fix a truncation issue in hugepages parameter
When we specify a large number for node in hugepages parameter, it may
be parsed to another number due to truncation in this statement:
node = tmp;
For example, add following parameter in command line:
hugepagesz=1G hugepages=
4294967297:5
and kernel will allocate 5 hugepages for node 1 instead of ignoring it.
I move the validation check earlier to fix this issue, and slightly
simplifies the condition here.
Link: https://lkml.kernel.org/r/20220209134018.8242-1-liuyuntao10@huawei.com
Fixes:
b5389086ad7be0 ("hugetlbfs: extend the definition of hugepages parameter to support node allocation")
Signed-off-by: Liu Yuntao <liuyuntao10@huawei.com>
Reviewed-by: Mike Kravetz <mike.kravetz@oracle.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andrey Konovalov [Sat, 26 Feb 2022 03:10:59 +0000 (19:10 -0800)]
kasan: test: prevent cache merging in kmem_cache_double_destroy
With HW_TAGS KASAN and kasan.stacktrace=off, the cache created in the
kmem_cache_double_destroy() test might get merged with an existing one.
Thus, the first kmem_cache_destroy() call won't actually destroy it but
will only decrease the refcount. This causes the test to fail.
Provide an empty constructor for the created cache to prevent the cache
from getting merged.
Link: https://lkml.kernel.org/r/b597bd434c49591d8af00ee3993a42c609dc9a59.1644346040.git.andreyknvl@google.com
Fixes:
f98f966cd750 ("kasan: test: add test case for double-kmem_cache_destroy()")
Signed-off-by: Andrey Konovalov <andreyknvl@google.com>
Reviewed-by: Marco Elver <elver@google.com>
Cc: Alexander Potapenko <glider@google.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Aneesh Kumar K.V [Sat, 26 Feb 2022 03:10:56 +0000 (19:10 -0800)]
mm/hugetlb: fix kernel crash with hugetlb mremap
This fixes the below crash:
kernel BUG at include/linux/mm.h:2373!
cpu 0x5d: Vector: 700 (Program Check) at [
c00000003c6e76e0]
pc:
c000000000581a54: pmd_to_page+0x54/0x80
lr:
c00000000058d184: move_hugetlb_page_tables+0x4e4/0x5b0
sp:
c00000003c6e7980
msr:
9000000000029033
current = 0xc00000003bd8d980
paca = 0xc000200fff610100 irqmask: 0x03 irq_happened: 0x01
pid = 9349, comm = hugepage-mremap
kernel BUG at include/linux/mm.h:2373!
move_hugetlb_page_tables+0x4e4/0x5b0 (link register)
move_hugetlb_page_tables+0x22c/0x5b0 (unreliable)
move_page_tables+0xdbc/0x1010
move_vma+0x254/0x5f0
sys_mremap+0x7c0/0x900
system_call_exception+0x160/0x2c0
the kernel can't use huge_pte_offset before it set the pte entry because
a page table lookup check for huge PTE bit in the page table to
differentiate between a huge pte entry and a pointer to pte page. A
huge_pte_alloc won't mark the page table entry huge and hence kernel
should not use huge_pte_offset after a huge_pte_alloc.
Link: https://lkml.kernel.org/r/20220211063221.99293-1-aneesh.kumar@linux.ibm.com
Fixes:
550a7d60bd5e ("mm, hugepages: add mremap() support for hugepage backed vma")
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Reviewed-by: Mike Kravetz <mike.kravetz@oracle.com>
Reviewed-by: Mina Almasry <almasrymina@google.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Luis Chamberlain [Sat, 26 Feb 2022 03:10:53 +0000 (19:10 -0800)]
MAINTAINERS: add sysctl-next git tree
Add a git tree for sysctls as there's been quite a bit of work lately to
remove all the syctls out of kernel/sysctl.c and move to their respective
places, so coordination has been needed to avoid conflicts. This tree
will also help soak these changes on linux-next prior to getting to Linus.
Link: https://lkml.kernel.org/r/20220218182736.3694508-1-mcgrof@kernel.org
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
Cc: Kees Cook <keescook@chromium.org>
Cc: Iurii Zaikin <yzaikin@google.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Max Staudt [Fri, 11 Feb 2022 14:10:36 +0000 (15:10 +0100)]
tty: Reserve ldisc 29 for development purposes
It's handy to have an ldisc number free for out-of-tree testing. This
way, a new ldisc can be developed on any running system, without having
to recompile the kernel just to define a new number.
This is the highest number (and also the last one) available under the
old numbering scheme, so let's reserve it before it's too late.
From now on, every new ldisc upstreamed will have to increment NR_LDISCS
in lockstep with its addition to the table in tty.h.
Signed-off-by: Max Staudt <max@enpas.org>
Link: https://lore.kernel.org/r/20220211141036.6403-1-max@enpas.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hammer Hsieh [Tue, 22 Feb 2022 09:36:03 +0000 (17:36 +0800)]
serial: sunplus-uart: Add Sunplus SoC UART Driver
Add Sunplus SoC UART Driver.
SP7021 UART block contains 5 UARTs.
There are UART0~4 that supported in SP7021, the features list as below.
Support Full-duplex communication.
Support data packet length configurable.
Support stop bit number configurable.
Support force break condition.
Support baud rate configurable.
Support error detection and report.
Support RXD Noise Rejection Vote configurable.
UART0 pinout only support TX/RX two pins.
UART1 to UART4 pinout support TX/RX/CTS/RTS four pins.
Normally UART0 used for kernel console, also can be used for normal uart.
Command line set "console=ttySUP0,115200", SUP means Sunplus Uart Port.
UART driver probe will create path named "/dev/ttySUPx".
https://sunplus.atlassian.net/wiki/spaces/doc/pages/
1873412290/13.+Universal+Asynchronous+Receiver+Transmitter+UART
Signed-off-by: Hammer Hsieh <hammerh0314@gmail.com>
Link: https://lore.kernel.org/r/1645522563-17183-3-git-send-email-hammerh0314@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hammer Hsieh [Tue, 22 Feb 2022 09:36:02 +0000 (17:36 +0800)]
dt-bindings: serial: Add bindings doc for Sunplus SoC UART Driver
Add bindings doc for Sunplus SoC UART Driver
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Hammer Hsieh <hammerh0314@gmail.com>
Link: https://lore.kernel.org/r/1645522563-17183-2-git-send-email-hammerh0314@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Uwe Kleine-König [Tue, 15 Feb 2022 16:02:36 +0000 (17:02 +0100)]
serial: 8250: Fix race condition in RTS-after-send handling
Set em485->active_timer = NULL isn't always enough to take out the stop
timer. While there is a check that it acts in the right state (i.e.
waiting for RTS-after-send to pass after sending some chars) but the
following might happen:
- CPU1: some chars send, shifter becomes empty, stop tx timer armed
- CPU0: more chars send before RTS-after-send expired
- CPU0: shifter empty irq, port lock taken
- CPU1: tx timer triggers, waits for port lock
- CPU0: em485->active_timer = &em485->stop_tx_timer, hrtimer_start(),
releases lock()
- CPU1: get lock, see em485->active_timer == &em485->stop_tx_timer,
tear down RTS too early
This fix bases on research done by Steffen Trumtrar.
Fixes:
b86f86e8e7c5 ("serial: 8250: fix potential deadlock in rs485-mode")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20220215160236.344236-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Yu Tu [Fri, 25 Feb 2022 07:39:22 +0000 (15:39 +0800)]
tty: serial: meson: Added S4 SOC compatibility
Make UART driver compatible with S4 SOC UART.
Signed-off-by: Yu Tu <yu.tu@amlogic.com>
Link: https://lore.kernel.org/r/20220225073922.3947-7-yu.tu@amlogic.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Yu Tu [Fri, 25 Feb 2022 07:39:21 +0000 (15:39 +0800)]
tty: serial: meson: The system stuck when you run the stty command on the console to change the baud rate
Start the console and run the following commands in turn:
stty -F /dev/ttyAML0 115200 and stty -F /dev/ttyAML0 921600. The
system will stuck.
Signed-off-by: Yu Tu <yu.tu@amlogic.com>
Link: https://lore.kernel.org/r/20220225073922.3947-6-yu.tu@amlogic.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Yu Tu [Fri, 25 Feb 2022 07:39:20 +0000 (15:39 +0800)]
tty: serial: meson: Make some bit of the REG5 register writable
Make the internal clock source mux and divider writeable, allowing the
uart to deviate from the settings intially applied by the ROMCode and
using the most appropriate clocks.
Signed-off-by: Yu Tu <yu.tu@amlogic.com>
Link: https://lore.kernel.org/r/20220225073922.3947-5-yu.tu@amlogic.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Yu Tu [Fri, 25 Feb 2022 07:39:19 +0000 (15:39 +0800)]
tty: serial: meson: Describes the calculation of the UART baud rate clock using a clock frame
Using the common Clock code to describe the UART baud rate clock
makes it easier for the UART driver to be compatible with the
baud rate requirements of the UART IP on different meson chips.
Signed-off-by: Yu Tu <yu.tu@amlogic.com>
Link: https://lore.kernel.org/r/20220225073922.3947-4-yu.tu@amlogic.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Yu Tu [Fri, 25 Feb 2022 07:39:18 +0000 (15:39 +0800)]
tty: serial: meson: Use devm_ioremap_resource to get register mapped memory
Replace devm_request_mem_region and devm_ioremap with
devm_ioremap_resource to make the code cleaner.
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Yu Tu <yu.tu@amlogic.com>
Link: https://lore.kernel.org/r/20220225073922.3947-3-yu.tu@amlogic.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Yu Tu [Fri, 25 Feb 2022 07:39:17 +0000 (15:39 +0800)]
tty: serial: meson: Move request the register region to probe
This simplifies resetting the UART controller during probe
and will make it easier to integrate the common clock code
which will require the registers at probe time as well.
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Yu Tu <yu.tu@amlogic.com>
Link: https://lore.kernel.org/r/20220225073922.3947-2-yu.tu@amlogic.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Daniel Bristot de Oliveira [Fri, 18 Feb 2022 17:57:09 +0000 (18:57 +0100)]
rtla/osnoise: Fix error message when failing to enable trace instance
When a trace instance creation fails, tools are printing:
Could not enable -> osnoiser <- tracer for tracing
Print the actual (and correct) name of the tracer it fails to enable.
Link: https://lkml.kernel.org/r/53ef0582605af91eca14b19dba9fc9febb95d4f9.1645206561.git.bristot@kernel.org
Fixes:
b1696371d865 ("rtla: Helper functions for rtla")
Cc: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Daniel Bristot de Oliveira <bristot@kernel.org>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Daniel Bristot de Oliveira [Fri, 18 Feb 2022 17:57:08 +0000 (18:57 +0100)]
rtla/osnoise: Free params at the exit
The variable that stores the parsed command line arguments are not
being free()d at the rtla osnoise top exit path.
Free params variable before exiting.
Link: https://lkml.kernel.org/r/0be31d8259c7c53b98a39769d60cfeecd8421785.1645206561.git.bristot@kernel.org
Fixes:
1eceb2fc2ca5 ("rtla/osnoise: Add osnoise top mode")
Cc: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Daniel Bristot de Oliveira <bristot@kernel.org>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Daniel Bristot de Oliveira [Fri, 18 Feb 2022 17:57:07 +0000 (18:57 +0100)]
rtla/hist: Make -E the short version of --entries
Currently, --entries uses -e as the short version in the hist mode of
timerlat and osnoise tools. But as -e is already used to enable events
on trace sessions by other tools, thus let's keep it available for the
same usage for all rtla tools.
Make -E the short version of --entries for hist mode on all tools.
Note: rtla was merged in this merge window, so rtla was not released yet.
Link: https://lkml.kernel.org/r/5dbf0cbe7364d3a05e708926b41a097c59a02b1e.1645206561.git.bristot@kernel.org
Cc: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Daniel Bristot de Oliveira <bristot@kernel.org>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Christophe Leroy [Mon, 20 Dec 2021 16:38:06 +0000 (16:38 +0000)]
tracing: Fix selftest config check for function graph start up test
CONFIG_DYNAMIC_FTRACE_WITH_DIRECT_CALLS is required to test
direct tramp.
Link: https://lkml.kernel.org/r/bdc7e594e13b0891c1d61bc8d56c94b1890eaed7.1640017960.git.christophe.leroy@csgroup.eu
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Steven Rostedt (Google) [Fri, 25 Feb 2022 20:34:26 +0000 (15:34 -0500)]
tracefs: Set the group ownership in apply_options() not parse_options()
Al Viro brought it to my attention that the dentries may not be filled
when the parse_options() is called, causing the call to set_gid() to
possibly crash. It should only be called if parse_options() succeeds
totally anyway.
He suggested the logical place to do the update is in apply_options().
Link: https://lore.kernel.org/all/20220225165219.737025658@goodmis.org/
Link: https://lkml.kernel.org/r/20220225153426.1c4cab6b@gandalf.local.home
Cc: stable@vger.kernel.org
Acked-by: Al Viro <viro@zeniv.linux.org.uk>
Reported-by: Al Viro <viro@zeniv.linux.org.uk>
Fixes:
48b27b6b5191 ("tracefs: Set all files to the same group ownership as the mount option")
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Linus Torvalds [Fri, 25 Feb 2022 22:12:36 +0000 (14:12 -0800)]
Merge tag 'configfs-5.17-2022-02-25' of git://git.infradead.org/users/hch/configfs
Pull configfs fix from Christoph Hellwig:
- fix a race in configfs_{,un}register_subsystem (ChenXiaoSong)
* tag 'configfs-5.17-2022-02-25' of git://git.infradead.org/users/hch/configfs:
configfs: fix a race in configfs_{,un}register_subsystem()
Linus Torvalds [Fri, 25 Feb 2022 22:08:03 +0000 (14:08 -0800)]
Merge tag 'for-5.17-rc5-tag' of git://git./linux/kernel/git/kdave/linux
Pull btrfs fixes from David Sterba:
"This is a hopefully last batch of fixes for defrag that got broken in
5.16, all stable material.
The remaining reported problem is excessive IO with autodefrag due to
various conditions in the defrag code not met or missing"
* tag 'for-5.17-rc5-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: reduce extent threshold for autodefrag
btrfs: autodefrag: only scan one inode once
btrfs: defrag: don't use merged extent map for their generation check
btrfs: defrag: bring back the old file extent search behavior
btrfs: defrag: remove an ambiguous condition for rejection
btrfs: defrag: don't defrag extents which are already at max capacity
btrfs: defrag: don't try to merge regular extents with preallocated extents
btrfs: defrag: allow defrag_one_cluster() to skip large extent which is not a target
btrfs: prevent copying too big compressed lzo segment
Linus Torvalds [Fri, 25 Feb 2022 21:34:30 +0000 (13:34 -0800)]
Merge tag 'for-linus' of git://git./linux/kernel/git/rdma/rdma
Pull rdma fixes from Jason Gunthorpe:
- Older "does not even boot" regression in qib from July
- Bug fixes for error unwind in rtrs
- Avoid a deadlock syzkaller found in srp
- Fix another UAF syzkaller found in cma
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
RDMA/cma: Do not change route.addr.src_addr outside state checks
RDMA/ib_srp: Fix a deadlock
RDMA/rtrs-clt: Move free_permit from free_clt to rtrs_clt_close
RDMA/rtrs-clt: Fix possible double free in error case
IB/qib: Fix duplicate sysfs directory name
Linus Torvalds [Fri, 25 Feb 2022 20:56:11 +0000 (12:56 -0800)]
Merge tag 'gpio-fixes-for-v5.17-rc6' of git://git./linux/kernel/git/brgl/linux
Pull gpio fixes from Bartosz Golaszewski:
- fix an bug generating spurious interrupts in gpio-rockchip
- fix a race condition in gpiod_to_irq() called by GPIO consumers
* tag 'gpio-fixes-for-v5.17-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux:
gpio: Return EPROBE_DEFER if gc->to_irq is NULL
gpio: rockchip: Reset int_bothedge when changing trigger
Jason Gunthorpe [Wed, 23 Feb 2022 15:23:57 +0000 (11:23 -0400)]
RDMA/cma: Do not change route.addr.src_addr outside state checks
If the state is not idle then resolve_prepare_src() should immediately
fail and no change to global state should happen. However, it
unconditionally overwrites the src_addr trying to build a temporary any
address.
For instance if the state is already RDMA_CM_LISTEN then this will corrupt
the src_addr and would cause the test in cma_cancel_operation():
if (cma_any_addr(cma_src_addr(id_priv)) && !id_priv->cma_dev)
Which would manifest as this trace from syzkaller:
BUG: KASAN: use-after-free in __list_add_valid+0x93/0xa0 lib/list_debug.c:26
Read of size 8 at addr
ffff8881546491e0 by task syz-executor.1/32204
CPU: 1 PID: 32204 Comm: syz-executor.1 Not tainted 5.12.0-rc8-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:79 [inline]
dump_stack+0x141/0x1d7 lib/dump_stack.c:120
print_address_description.constprop.0.cold+0x5b/0x2f8 mm/kasan/report.c:232
__kasan_report mm/kasan/report.c:399 [inline]
kasan_report.cold+0x7c/0xd8 mm/kasan/report.c:416
__list_add_valid+0x93/0xa0 lib/list_debug.c:26
__list_add include/linux/list.h:67 [inline]
list_add_tail include/linux/list.h:100 [inline]
cma_listen_on_all drivers/infiniband/core/cma.c:2557 [inline]
rdma_listen+0x787/0xe00 drivers/infiniband/core/cma.c:3751
ucma_listen+0x16a/0x210 drivers/infiniband/core/ucma.c:1102
ucma_write+0x259/0x350 drivers/infiniband/core/ucma.c:1732
vfs_write+0x28e/0xa30 fs/read_write.c:603
ksys_write+0x1ee/0x250 fs/read_write.c:658
do_syscall_64+0x2d/0x70 arch/x86/entry/common.c:46
entry_SYSCALL_64_after_hwframe+0x44/0xae
This is indicating that an rdma_id_private was destroyed without doing
cma_cancel_listens().
Instead of trying to re-use the src_addr memory to indirectly create an
any address derived from the dst build one explicitly on the stack and
bind to that as any other normal flow would do. rdma_bind_addr() will copy
it over the src_addr once it knows the state is valid.
This is similar to commit
bc0bdc5afaa7 ("RDMA/cma: Do not change
route.addr.src_addr.ss_family")
Link: https://lore.kernel.org/r/0-v2-e975c8fd9ef2+11e-syz_cma_srcaddr_jgg@nvidia.com
Cc: stable@vger.kernel.org
Fixes:
732d41c545bb ("RDMA/cma: Make the locking for automatic state transition more clear")
Reported-by: syzbot+c94a3675a626f6333d74@syzkaller.appspotmail.com
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Linus Torvalds [Fri, 25 Feb 2022 20:37:41 +0000 (12:37 -0800)]
Merge tag 'spi-fix-v5.17-rc5' of git://git./linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"A few small driver specific fixes"
* tag 'spi-fix-v5.17-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: rockchip: terminate dma transmission when slave abort
spi: rockchip: Fix error in getting num-cs property
spi: spi-zynq-qspi: Fix a NULL pointer dereference in zynq_qspi_exec_mem_op()
Linus Torvalds [Fri, 25 Feb 2022 20:33:51 +0000 (12:33 -0800)]
Merge tag 'regulator-fix-v5.17-rc5' of git://git./linux/kernel/git/broonie/regulator
Pull regulator fixes from Mark Brown:
"A series of fixes for the da9121 driver"
* tag 'regulator-fix-v5.17-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: da9121: Remove surplus DA9141 parameters
regulator: da9121: Fix DA914x voltage value
regulator: da9121: Fix DA914x current values
Linus Torvalds [Fri, 25 Feb 2022 20:30:01 +0000 (12:30 -0800)]
Merge tag 'regmap-fix-v5.17-rc5' of git://git./linux/kernel/git/broonie/regmap
Pull regmap fix from Mark Brown:
"A fix for interrupt controllers which require the explicit
acknowledgement of interrupts using a different register to the one
where interrupts are reported.
Urgent for the few devices this affects"
* tag 'regmap-fix-v5.17-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap-irq: Update interrupt clear register for proper reset
Linus Torvalds [Fri, 25 Feb 2022 20:25:44 +0000 (12:25 -0800)]
Merge tag 'thermal-5.17-rc6' of git://git./linux/kernel/git/rafael/linux-pm
Pull thermal control fix from Rafael Wysocki:
"Fix a memory leak in the int340x thermal driver's ACPI notify handler
(Chuansheng Liu)"
* tag 'thermal-5.17-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
thermal: int340x: fix memory leak in int3400_notify()
Linus Torvalds [Fri, 25 Feb 2022 20:17:20 +0000 (12:17 -0800)]
Merge tag 'pm-5.17-rc6' of git://git./linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"Fix the throttle IRQ handling during cpufreq initialization on
Qualcomm platforms (Bjorn Andersson)"
* tag 'pm-5.17-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpufreq: qcom-hw: Delay enabling throttle_irq
cpufreq: Reintroduce ready() callback
Linus Torvalds [Fri, 25 Feb 2022 20:12:06 +0000 (12:12 -0800)]
Merge tag 'char-misc-5.17-rc6' of git://git./linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes from Greg KH:
"Here are a few small driver fixes for 5.17-rc6 for reported issues.
The majority of these are IIO fixes for small things, and the other
two are a mvmem and mtd core conflict fix.
All of these have been in linux-next with no reported issues"
* tag 'char-misc-5.17-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
mtd: core: Fix a conflict between MTD and NVMEM on wp-gpios property
nvmem: core: Fix a conflict between MTD and NVMEM on wp-gpios property
iio: imu: st_lsm6dsx: wait for settling time in st_lsm6dsx_read_oneshot
iio: Fix error handling for PM
iio: addac: ad74413r: correct comparator gpio getters mask usage
iio: addac: ad74413r: use ngpio size when iterating over mask
iio: addac: ad74413r: Do not reference negative array offsets
iio: adc: men_z188_adc: Fix a resource leak in an error handling path
iio: frequency: admv1013: remove the always true condition
iio: accel: fxls8962af: add padding to regmap for SPI
iio:imu:adis16480: fix buffering for devices with no burst mode
iio: adc: ad7124: fix mask used for setting AIN_BUFP & AIN_BUFM bits
iio: adc: tsc2046: fix memory corruption by preventing array overflow
Linus Torvalds [Fri, 25 Feb 2022 20:05:40 +0000 (12:05 -0800)]
Merge tag 'driver-core-5.17-rc6' of git://git./linux/kernel/git/gregkh/driver-core
Pull driver core fix from Greg KH:
"Here is a single driver core fix for 5.17-rc6. It resolves a reported
problem when the DMA map of a device is not properly released.
It has been in linux-next with no reported problems"
* tag 'driver-core-5.17-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
driver core: Free DMA range map when device is released
Linus Torvalds [Fri, 25 Feb 2022 19:56:16 +0000 (11:56 -0800)]
Merge tag 'staging-5.17-rc6' of git://git./linux/kernel/git/gregkh/staging
Pull staging driver fix from Greg KH:
"Here is a single staging driver fix for 5.17-rc6.
It resolves a reported problem in the fbtft fb_st7789v.c driver that
could cause the display to be flipped in cold weather.
It has been in linux-next with no reported problems"
* tag 'staging-5.17-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: fbtft: fb_st7789v: reset display before initialization
Linus Torvalds [Fri, 25 Feb 2022 19:45:29 +0000 (11:45 -0800)]
Merge tag 'tty-5.17-rc6' of git://git./linux/kernel/git/gregkh/tty
Pull tty/serial driver fixes from Greg KH:
"Here are some small n_gsm and sc16is7xx serial driver fixes for
5.17-rc6.
The n_gsm fixes are from Siemens as it seems they are using the line
discipline and fixing up a number of issues they found in their
testing. The sc16is7xx serial driver fix is for a reported problem
with that chip.
All of these have been in linux-next with no reported problems"
* tag 'tty-5.17-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
sc16is7xx: Fix for incorrect data being transmitted
tty: n_gsm: fix deadlock in gsmtty_open()
tty: n_gsm: fix wrong modem processing in convergence layer type 2
tty: n_gsm: fix wrong tty control line for flow control
tty: n_gsm: fix NULL pointer access due to DLCI release
tty: n_gsm: fix proper link termination after failed open
tty: n_gsm: fix encoding of command/response bit
tty: n_gsm: fix encoding of control signal octet bit DV
Linus Torvalds [Fri, 25 Feb 2022 19:36:31 +0000 (11:36 -0800)]
Merge tag 'usb-5.17-rc6' of git://git./linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are a number of small USB driver fixes for 5.17-rc6 to resolve
reported problems and add new device ids. They include:
- dwc3:
- device mapping fix
- new device ids
- driver fixes
- xhci driver fixes
- gadget driver fixes
- usb-serial driver device id updates
All of these have been in linux-next with no reported problems"
* tag 'usb-5.17-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
usb: gadget: rndis: add spinlock for rndis response list
usb: dwc3: gadget: Let the interrupt handler disable bottom halves.
USB: gadget: validate endpoint index for xilinx udc
USB: serial: option: add Telit LE910R1 compositions
USB: serial: option: add support for DW5829e
Revert "USB: serial: ch341: add new Product ID for CH341A"
usb: dwc2: drd: fix soft connect when gadget is unconfigured
usb: dwc3: pci: Fix Bay Trail phy GPIO mappings
tps6598x: clear int mask on probe failure
xhci: Prevent futile URB re-submissions due to incorrect return value.
xhci: re-initialize the HC during resume if HCE was set
usb: dwc3: pci: Add "snps,dis_u2_susphy_quirk" for Intel Bay Trail
usb: dwc3: pci: add support for the Intel Raptor Lake-S
Linus Torvalds [Fri, 25 Feb 2022 19:22:19 +0000 (11:22 -0800)]
Merge tag 'ata-5.17-rc6' of git://git./linux/kernel/git/dlemoal/libata
Pull ata fixes from Damien Le Moal:
"Two fixes for the pata_hpt37x driver, both from Sergey:
- Fix a PCI register access using an incorrect size (8bits instead of
16bits)
- Make sure to always disable the primary channel as it is unused"
* tag 'ata-5.17-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/libata:
ata: pata_hpt37x: disable primary channel on HPT371
ata: pata_hpt37x: fix PCI clock detection
Daniel Bristot de Oliveira [Fri, 18 Feb 2022 15:17:38 +0000 (16:17 +0100)]
tracing/osnoise: Make osnoise_main to sleep for microseconds
osnoise's runtime and period are in the microseconds scale, but it is
currently sleeping in the millisecond's scale. This behavior roots in the
usage of hwlat as the skeleton for osnoise.
Make osnoise to sleep in the microseconds scale. Also, move the sleep to
a specialized function.
Link: https://lkml.kernel.org/r/302aa6c7bdf2d131719b22901905e9da122a11b2.1645197336.git.bristot@kernel.org
Cc: Ingo Molnar <mingo@redhat.com>
Signed-off-by: Daniel Bristot de Oliveira <bristot@kernel.org>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Nathan Chancellor [Mon, 14 Feb 2022 19:28:47 +0000 (12:28 -0700)]
ftrace: Remove unused ftrace_startup_enable() stub
When building with clang + CONFIG_DYNAMIC_FTRACE=n + W=1, there is a
warning:
kernel/trace/ftrace.c:7194:20: error: unused function 'ftrace_startup_enable' [-Werror,-Wunused-function]
static inline void ftrace_startup_enable(int command) { }
^
1 error generated.
Clang warns on instances of static inline functions in .c files with W=1
after commit
6863f5643dd7 ("kbuild: allow Clang to find unused static
inline functions for W=1 build").
The ftrace_startup_enable() stub has been unused since
commit
e1effa0144a1 ("ftrace: Annotate the ops operation on update"),
where its use outside of the CONFIG_DYNAMIC_TRACE section was replaced
by ftrace_startup_all(). Remove it to resolve the warning.
Link: https://lkml.kernel.org/r/20220214192847.488166-1-nathan@kernel.org
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Sven Schnelle [Mon, 14 Feb 2022 13:44:56 +0000 (14:44 +0100)]
tracing: Ensure trace buffer is at least 4096 bytes large
Booting the kernel with 'trace_buf_size=1' give a warning at
boot during the ftrace selftests:
[ 0.892809] Running postponed tracer tests:
[ 0.892893] Testing tracer function:
[ 0.901899] Callback from call_rcu_tasks_trace() invoked.
[ 0.983829] Callback from call_rcu_tasks_rude() invoked.
[ 1.072003] .. bad ring buffer .. corrupted trace buffer ..
[ 1.091944] Callback from call_rcu_tasks() invoked.
[ 1.097695] PASSED
[ 1.097701] Testing dynamic ftrace: .. filter failed count=0 ..FAILED!
[ 1.353474] ------------[ cut here ]------------
[ 1.353478] WARNING: CPU: 0 PID: 1 at kernel/trace/trace.c:1951 run_tracer_selftest+0x13c/0x1b0
Therefore enforce a minimum of 4096 bytes to make the selftest pass.
Link: https://lkml.kernel.org/r/20220214134456.1751749-1-svens@linux.ibm.com
Signed-off-by: Sven Schnelle <svens@linux.ibm.com>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Christophe Leroy [Fri, 11 Feb 2022 07:10:18 +0000 (08:10 +0100)]
tracing: Uninline trace_trigger_soft_disabled() partly
On a powerpc32 build with CONFIG_CC_OPTIMISE_FOR_SIZE, the inline
keyword is not honored and trace_trigger_soft_disabled() appears
approx 50 times in vmlinux.
Adding -Winline to the build, the following message appears:
./include/linux/trace_events.h:712:1: error: inlining failed in call to 'trace_trigger_soft_disabled': call is unlikely and code size would grow [-Werror=inline]
That function is rather big for an inlined function:
c003df60 <trace_trigger_soft_disabled>:
c003df60: 94 21 ff f0 stwu r1,-16(r1)
c003df64: 7c 08 02 a6 mflr r0
c003df68: 90 01 00 14 stw r0,20(r1)
c003df6c: bf c1 00 08 stmw r30,8(r1)
c003df70: 83 e3 00 24 lwz r31,36(r3)
c003df74: 73 e9 01 00 andi. r9,r31,256
c003df78: 41 82 00 10 beq
c003df88 <trace_trigger_soft_disabled+0x28>
c003df7c: 38 60 00 00 li r3,0
c003df80: 39 61 00 10 addi r11,r1,16
c003df84: 4b fd 60 ac b
c0014030 <_rest32gpr_30_x>
c003df88: 73 e9 00 80 andi. r9,r31,128
c003df8c: 7c 7e 1b 78 mr r30,r3
c003df90: 41 a2 00 14 beq
c003dfa4 <trace_trigger_soft_disabled+0x44>
c003df94: 38 c0 00 00 li r6,0
c003df98: 38 a0 00 00 li r5,0
c003df9c: 38 80 00 00 li r4,0
c003dfa0: 48 05 c5 f1 bl
c009a590 <event_triggers_call>
c003dfa4: 73 e9 00 40 andi. r9,r31,64
c003dfa8: 40 82 00 28 bne
c003dfd0 <trace_trigger_soft_disabled+0x70>
c003dfac: 73 ff 02 00 andi. r31,r31,512
c003dfb0: 41 82 ff cc beq
c003df7c <trace_trigger_soft_disabled+0x1c>
c003dfb4: 80 01 00 14 lwz r0,20(r1)
c003dfb8: 83 e1 00 0c lwz r31,12(r1)
c003dfbc: 7f c3 f3 78 mr r3,r30
c003dfc0: 83 c1 00 08 lwz r30,8(r1)
c003dfc4: 7c 08 03 a6 mtlr r0
c003dfc8: 38 21 00 10 addi r1,r1,16
c003dfcc: 48 05 6f 6c b
c0094f38 <trace_event_ignore_this_pid>
c003dfd0: 38 60 00 01 li r3,1
c003dfd4: 4b ff ff ac b
c003df80 <trace_trigger_soft_disabled+0x20>
However it is located in a hot path so inlining it is important.
But forcing inlining of the entire function by using __always_inline
leads to increasing the text size by approx 20 kbytes.
Instead, split the fonction in two parts, one part with the likely
fast path, flagged __always_inline, and a second part out of line.
With this change, on a powerpc32 with CONFIG_CC_OPTIMISE_FOR_SIZE
vmlinux text increases by only 1,4 kbytes, which is partly
compensated by a decrease of vmlinux data by 7 kbytes.
On ppc64_defconfig which has CONFIG_CC_OPTIMISE_FOR_SPEED, this
change reduces vmlinux text by more than 30 kbytes.
Link: https://lkml.kernel.org/r/69ce0986a52d026d381d612801d978aa4f977460.1644563295.git.christophe.leroy@csgroup.eu
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Steven Rostedt (Google) [Sat, 19 Feb 2022 00:00:57 +0000 (19:00 -0500)]
eprobes: Remove redundant event type information
Currently, the event probes save the type of the event they are attached
to when recording the event. For example:
# echo 'e:switch sched/sched_switch prev_state=$prev_state prev_prio=$prev_prio next_pid=$next_pid next_prio=$next_prio' > dynamic_events
# cat events/eprobes/switch/format
name: switch
ID: 1717
format:
field:unsigned short common_type; offset:0; size:2; signed:0;
field:unsigned char common_flags; offset:2; size:1; signed:0;
field:unsigned char common_preempt_count; offset:3; size:1; signed:0;
field:int common_pid; offset:4; size:4; signed:1;
field:unsigned int __probe_type; offset:8; size:4; signed:0;
field:u64 prev_state; offset:12; size:8; signed:0;
field:u64 prev_prio; offset:20; size:8; signed:0;
field:u64 next_pid; offset:28; size:8; signed:0;
field:u64 next_prio; offset:36; size:8; signed:0;
print fmt: "(%u) prev_state=0x%Lx prev_prio=0x%Lx next_pid=0x%Lx next_prio=0x%Lx", REC->__probe_type, REC->prev_state, REC->prev_prio, REC->next_pid, REC->next_prio
The __probe_type adds 4 bytes to every event.
One of the reasons for creating eprobes is to limit what is traced in an
event to be able to limit what is written into the ring buffer. Having
this redundant 4 bytes to every event takes away from this.
The event that is recorded can be retrieved from the event probe itself,
that is available when the trace is happening. For user space tools, it
could simply read the dynamic_event file to find the event they are for.
So there is really no reason to write this information into the ring
buffer for every event.
Link: https://lkml.kernel.org/r/20220218190057.2f5a19a8@gandalf.local.home
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Reviewed-by: Joel Fernandes <joel@joelfernandes.org>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Steven Rostedt (Google) [Thu, 24 Feb 2022 03:38:37 +0000 (22:38 -0500)]
tracing: Have traceon and traceoff trigger honor the instance
If a trigger is set on an event to disable or enable tracing within an
instance, then tracing should be disabled or enabled in the instance and
not at the top level, which is confusing to users.
Link: https://lkml.kernel.org/r/20220223223837.14f94ec3@rorschach.local.home
Cc: stable@vger.kernel.org
Fixes:
ae63b31e4d0e2 ("tracing: Separate out trace events from global variables")
Tested-by: Daniel Bristot de Oliveira <bristot@kernel.org>
Reviewed-by: Tom Zanussi <zanussi@kernel.org>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Jiri Slaby [Thu, 24 Feb 2022 11:10:27 +0000 (12:10 +0100)]
tty: serial: amba-pl010: use more uart_port pointers
The code uses uart_amba_port::port on many places. Sometimes it even
needs not uart_amba_port itself. So simplify the code on many places
and remove the need of uart_amba_port on some places completely.
No functional changes intended. The objdump -d output shows only a code
move in pl010_rx_chars().
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Russell King <linux@armlinux.org.uk>
Link: https://lore.kernel.org/r/20220224111028.20917-5-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jiri Slaby [Thu, 24 Feb 2022 11:10:28 +0000 (12:10 +0100)]
tty: serial: lpc32xx_hs: use serial_lpc32xx_stop_tx() helper
Instead of open-coding what serial_lpc32xx_stop_tx() already does, call
it in __serial_lpc32xx_tx() directly.
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220224111028.20917-6-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jiri Slaby [Thu, 24 Feb 2022 11:10:25 +0000 (12:10 +0100)]
tty: serial: serial_txx9: remove info print from init
Remove the hello print among with version and name definitions. Drivers
should print nothing if they are successful.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220224111028.20917-3-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jiri Slaby [Thu, 24 Feb 2022 11:10:24 +0000 (12:10 +0100)]
tty: serial: mpc52xx_uart: make rx/tx hooks return unsigned
All these return bitmasks, so it makes more sense to return unsigned --
this is what a reader and also all the callers expect.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220224111028.20917-2-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Andy Shevchenko [Wed, 23 Feb 2022 15:12:40 +0000 (17:12 +0200)]
serial: 8250_lpss: Balance reference count for PCI DMA device
The pci_get_slot() increases its reference count, the caller
must decrement the reference count by calling pci_dev_put().
Fixes:
9a1870ce812e ("serial: 8250: don't use slave_id of dma_slave_config")
Depends-on:
a13e19cf3dc1 ("serial: 8250_lpss: split LPSS driver to separate module")
Reported-by: Qing Wang <wangqing@vivo.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220223151240.70248-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Andy Shevchenko [Tue, 15 Feb 2022 10:09:20 +0000 (12:09 +0200)]
serial: 8250_mid: Balance reference count for PCI DMA device
The pci_get_slot() increases its reference count, the caller
must decrement the reference count by calling pci_dev_put().
Fixes:
90b9aacf912a ("serial: 8250_pci: add Intel Tangier support")
Fixes:
f549e94effa1 ("serial: 8250_pci: add Intel Penwell ports")
Reported-by: Qing Wang <wangqing@vivo.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Depends-on:
d9eda9bab237 ("serial: 8250_pci: Intel MID UART support to its own driver")
Link: https://lore.kernel.org/r/20220215100920.41984-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Yang Guang [Sat, 12 Feb 2022 02:19:48 +0000 (10:19 +0800)]
serial: 8250_aspeed_vuart: replace snprintf with sysfs_emit
coccinelle report:
./drivers/tty/serial/8250/8250_aspeed_vuart.c:85:8-16:
WARNING: use scnprintf or sprintf
./drivers/tty/serial/8250/8250_aspeed_vuart.c:174:8-16:
WARNING: use scnprintf or sprintf
./drivers/tty/serial/8250/8250_aspeed_vuart.c:127:8-16:
WARNING: use scnprintf or sprintf
Use sysfs_emit instead of scnprintf or sprintf makes more sense.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Yang Guang <yang.guang5@zte.com.cn>
Signed-off-by: David Yang <davidcomponentone@gmail.com>
Link: https://lore.kernel.org/r/fed40753603dac4d14b17970c88e6f5f936348c1.1644541843.git.yang.guang5@zte.com.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Maciej W. Rozycki [Sat, 12 Feb 2022 17:30:53 +0000 (17:30 +0000)]
serial: 8250: Correct Kconfig help text for blacklisted PCI devices
Correct the Kconfig help text for SERIAL_8250_LPSS, SERIAL_8250_MID and
SERIAL_8250_PERICOM configuration options for dedicated PCI UART drivers
that have been blacklisted in the generic PCI 8250 UART driver and as
from commit
a13e19cf3dc10 ("serial: 8250_lpss: split LPSS driver to
separate module"), commit
d9eda9bab2372 ("serial: 8250_pci: Intel MID
UART support to its own driver"), and commit
fcfd3c09f4078 ("serial:
8250_pci: Split out Pericom driver") respectively are not handled by
said driver anymore (rather than for extra features only, as the current
text indicates), and therefore require the respective dedicated drivers
to work at all.
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2202121704560.34636@angie.orcam.me.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pali Rohár [Sat, 19 Feb 2022 15:28:18 +0000 (16:28 +0100)]
arm64: dts: marvell: armada-37xx: add device node for UART clock and use it
Define DT node for UART clock "marvell,armada-3700-uart-clock" and use
this UART clock as a base clock for all UART devices.
Reviewed-by: Marek Behún <kabel@kernel.org>
Acked-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Link: https://lore.kernel.org/r/20220219152818.4319-7-kabel@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pali Rohár [Sat, 19 Feb 2022 15:28:17 +0000 (16:28 +0100)]
serial: mvebu-uart: implement support for baudrates higher than 230400 Bd
Implement simple usage of fractional divisor. When main divisor D is too
large to represent requested baudrate then use divisor M from the
fractional divisor feature. All the M prescalers are set to the same and
maximal value 63, so the fractional part of the fractional divisor is not
used at all. We also determine upper limit for possible baudrates.
Experiments show that UART at baudrate 1500000 Bd with this configuration
is stable. So there is no need to implement complicated calculation of
fractional coefficients yet.
To use this feature with higher baudrates, it is required to use UART clock
provided by UART clock driver. Default boot xtal clock is not capable of
higher baudrates.
Reviewed-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Link: https://lore.kernel.org/r/20220219152818.4319-6-kabel@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pali Rohár [Sat, 19 Feb 2022 15:28:16 +0000 (16:28 +0100)]
dt-bindings: mvebu-uart: update information about UART clock
Device "marvell,armada-3700-uart" should use
"marvell,armada-3700-uart-clock" compatible clock.
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Link: https://lore.kernel.org/r/20220219152818.4319-5-kabel@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pali Rohár [Sat, 19 Feb 2022 15:28:15 +0000 (16:28 +0100)]
serial: mvebu-uart: implement UART clock driver for configuring UART base clock
Implement a new device driver for controlling UART clocks on Marvell
Armada 3700 SoC. This device driver is loaded for devices which match
the compatible string "marvell,armada-3700-uart-clock".
There are more pitfalls related to UART clocks:
- both UARTs use same parent clock source (which can be xtal or one of
the TBG clocks),
- if a TBG clock is used as the parent clock, there are two additional
divisors that can both be configured to divide the rate by 1, 2, ... 6,
but these divisors are again shared between the two UART controllers
on the SOC,
- the configuration of the parent clock source and divisors is done in
the address space of the first UART controller, UART1. Clocks can be
gated separately for UART1 and UART2, but this setting also lives in
the address space of UART1,
- Marvell's Functional Specification for Armada 3720 document has the
clock gating bits swapped, so the one described to gate UART1 clock
actually gates UART2 and vice versa,
- each UART has it's own "special divisor", and this uses the parent
clock described above. These divisors are configure in each UART's
address space separately.
Thus the driver for UART2 controller needs to have access to UART1
address space, since UART1 address space contains some bits exclusive
for UART2 and also some bits which are shared between UART1 and UART2.
Also, during boot, when early console is active on one of the UARTs,
and we want to switch parent clock from xtal (default) to TBG (to be
more flexible with baudrates), the driver changing UART clocks also
needs to be able to change the "special divisor", so that the baudrate
of earlycon is not changed when swtiching to normal console. Thus the
clock driver also needs to be able to access UART2 register space,
for UART2's "special divisor".
For these reasons, this new UART clock driver does not use
ioremap_resource(), but only ioremap() to prevent resource conflicts
between UART clock driver and UART driver.
We need to share only two 32-bit registers between the UART driver and
the UART clock driver:
- UART Clock Control
- UART 2 Baud Rate Divisor
Access to these two registers are protected by one spinlock to prevent
any conflicts. Access is required only during probing, when changing
baudrate or during suspend/resume.
Hardware can be configured to use one of following clocks as UART parent
clock: TBG-A-P, TBG-B-P, TBG-A-S, TBG-B-S, xtal. Not every clock is
usable for higher buadrates. Any subset can be specified in the
device-tree and the driver will choose the best one which also still
supports the mandatory baudrate of 9600 Bd. For smooth boot log output
it is needed to specify clock used by early console, otherwise garbage
would be printed on UART during probe of UART clock driver and
transitioning from early console to normal console.
We are implementing this to be able to configure TBG clock as UART
parent clock, which is required to be able to achieve higher baudrates
than 230400 Bd. We achieve this by referencing this new UART clock
device node in UART's device node. UART clock device driver
automatically chooses the best clock source for UART driver.
Until now, UART's device-tree node needed to reference one of the static
clocks (xtal or one of the TBGs) as parent clock in the `clocks`
phandle - the parent clock which was configured before booting the
kernel. If bootloader changed UART's parent clock, it needed to change
the `clocks` phandle in DTB correspondingly before booting.
From now on both the old mechanism (xtal or TBG referenced as parent
clock in `clocks` phandle) and the new one (UART clock referenced in the
`clocks` phandle) are supported, to provide full backward compatibility
with existing DTS files, full backward compatibility with existing boot
loaders, and to provide new features (runtime clock configuration to
allow higher baudrates than 230400 Bd). New features are available only
with new DTS files.
There was also a discussion about how the UART node and the
clock-controller node could be wrapped together in a new binding [1, 2].
As explained there, this is not possible if we want to keep backwards
compatibility with existing bootloaders, and thus we are doing this by
putting the UART clock-controller node inside the UART1 node.
[1] https://lore.kernel.org/linux-serial/
20220120000651.in7s6nazif5qjkme@pali/
[2] https://lore.kernel.org/linux-serial/
20220125204006.
A6D09C340E0@smtp.kernel.org/
Reviewed-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Link: https://lore.kernel.org/r/20220219152818.4319-4-kabel@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pali Rohár [Sat, 19 Feb 2022 15:28:14 +0000 (16:28 +0100)]
dt-bindings: mvebu-uart: document DT bindings for marvell,armada-3700-uart-clock
Add DT bindings documentation for device nodes with compatible string
"marvell,armada-3700-uart-clock".
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Link: https://lore.kernel.org/r/20220219152818.4319-3-kabel@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pali Rohár [Sat, 19 Feb 2022 15:28:13 +0000 (16:28 +0100)]
math64: New DIV_U64_ROUND_CLOSEST helper
Provide DIV_U64_ROUND_CLOSEST helper which uses div_u64 to perform
division rounded to the closest integer using unsigned 64bit
dividend and unsigned 32bit divisor.
Reviewed-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Link: https://lore.kernel.org/r/20220219152818.4319-2-kabel@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Lech Perczak [Mon, 21 Feb 2022 10:56:15 +0000 (11:56 +0100)]
sc16is7xx: Separate GPIOs from modem control lines
Export only the GPIOs that are not shared with hardware modem control
lines. Introduce new device parameter indicating whether modem control
lines are available.
Signed-off-by: Lech Perczak <l.perczak@camlintechnologies.com>
Signed-off-by: Tomasz Moń <tomasz.mon@camlingroup.com>
Link: https://lore.kernel.org/r/20220221105618.3503470-4-tomasz.mon@camlingroup.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Lech Perczak [Mon, 21 Feb 2022 10:56:14 +0000 (11:56 +0100)]
sc16is7xx: Update status lines in single call
RTS, DTR and LOOP bits can be updated in a single MCR register update.
This reduces the number of (slow) SPI/I2C bus transactions.
Signed-off-by: Lech Perczak <l.perczak@camlintechnologies.com>
Signed-off-by: Tomasz Moń <tomasz.mon@camlingroup.com>
Link: https://lore.kernel.org/r/20220221105618.3503470-3-tomasz.mon@camlingroup.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Lech Perczak [Mon, 21 Feb 2022 10:56:13 +0000 (11:56 +0100)]
sc16is7xx: Preserve EFR bits on update
Preserve unaffected bits state when accessing EFR register. This
prevents hardware flow control bits from being cleared on enhanced
functions access.
Signed-off-by: Lech Perczak <l.perczak@camlintechnologies.com>
Signed-off-by: Tomasz Moń <tomasz.mon@camlingroup.com>
Link: https://lore.kernel.org/r/20220221105618.3503470-2-tomasz.mon@camlingroup.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Steffen Trumtrar [Thu, 17 Feb 2022 21:18:39 +0000 (22:18 +0100)]
serial: 8250: Return early in .start_tx() if there are no chars to send
Don't start the whole chain for TX if there is no data to send. This is
mostly relevant for rs485 mode as there might be rts-before-send and
rts-after-send delays involved.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20220217211839.443039-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pali Rohár [Tue, 22 Feb 2022 10:54:06 +0000 (11:54 +0100)]
MAINTAINERS: Add Pali Rohár as mvebu-uart.c maintainer
Add Pali Rohár as mvebu-uart.c maintainer
Signed-off-by: Pali Rohár <pali@kernel.org>
Link: https://lore.kernel.org/r/20220222105406.28894-1-pali@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ilpo Järvinen [Tue, 22 Feb 2022 11:56:04 +0000 (13:56 +0200)]
xtensa: termbits.h is identical to asm-generic one
Remove arch specific termbits.h as there are only trivial space
differences between include/uapi/asm-generic/termbits.h and
arch/xtensa/include/uapi/asm/termbits.h.
$ diff -u0 -b -B include/uapi/asm-generic/termbits.h arch/xtensa/include/uapi/asm/termbits.h
. --- include/uapi/asm-generic/termbits.h 2022-01-10 13:44:42.
814107461 +0200
. +++ arch/xtensa/include/uapi/asm/termbits.h 2022-01-10 13:44:42.
690106926 +0200
. @@ -2,2 +2,15 @@
. -#ifndef __ASM_GENERIC_TERMBITS_H
. -#define __ASM_GENERIC_TERMBITS_H
. +/*
. + * include/asm-xtensa/termbits.h
. + *
. + * Copied from SH.
. + *
. + * This file is subject to the terms and conditions of the GNU General Public
. + * License. See the file "COPYING" in the main directory of this archive
. + * for more details.
. + *
. + * Copyright (C) 2001 - 2005 Tensilica Inc.
. + */
. +
. +#ifndef _XTENSA_TERMBITS_H
. +#define _XTENSA_TERMBITS_H
. +
. @@ -200 +221 @@
. -#endif /* __ASM_GENERIC_TERMBITS_H */
. +#endif /* _XTENSA_TERMBITS_H */
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220222115604.7351-3-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ilpo Järvinen [Tue, 22 Feb 2022 11:56:03 +0000 (13:56 +0200)]
ia64: termbits.h is identical to asm-generic one
Remove arch specific termbits.h as there are only trivial space
differences between include/uapi/asm-generic/termbits.h and
arch/ia64/include/uapi/asm/termbits.h:
$ diff -u0 -b -B include/uapi/asm-generic/termbits.h arch/ia64/include/uapi/asm/termbits.h
. --- include/uapi/asm-generic/termbits.h 2022-01-10 13:44:42.
814107461 +0200
. +++ arch/ia64/include/uapi/asm/termbits.h 2022-01-10 13:44:42.
678106874 +0200
. @@ -2,2 +2,11 @@
. -#ifndef __ASM_GENERIC_TERMBITS_H
. -#define __ASM_GENERIC_TERMBITS_H
. +#ifndef _ASM_IA64_TERMBITS_H
. +#define _ASM_IA64_TERMBITS_H
. +
. +/*
. + * Based on <asm-i386/termbits.h>.
. + *
. + * Modified 1999
. + * David Mosberger-Tang <davidm@hpl.hp.com>, Hewlett-Packard Co
. + *
. + * 99/01/28 Added new baudrates
. + */
. @@ -200 +209 @@
. -#endif /* __ASM_GENERIC_TERMBITS_H */
. +#endif /* _ASM_IA64_TERMBITS_H */
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220222115604.7351-2-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Changbin Du [Sun, 13 Feb 2022 08:18:45 +0000 (16:18 +0800)]
riscv: fix oops caused by irqsoff latency tracer
The trace_hardirqs_{on,off}() require the caller to setup frame pointer
properly. This because these two functions use macro 'CALLER_ADDR1' (aka.
__builtin_return_address(1)) to acquire caller info. If the $fp is used
for other purpose, the code generated this macro (as below) could trigger
memory access fault.
0xffffffff8011510e <+80>: ld a1,-16(s0)
0xffffffff80115112 <+84>: ld s2,-8(a1) # <-- paging fault here
The oops message during booting if compiled with 'irqoff' tracer enabled:
[ 0.039615][ T0] Unable to handle kernel NULL pointer dereference at virtual address
00000000000000f8
[ 0.041925][ T0] Oops [#1]
[ 0.042063][ T0] Modules linked in:
[ 0.042864][ T0] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.17.0-rc1-00233-g9a20c48d1ed2 #29
[ 0.043568][ T0] Hardware name: riscv-virtio,qemu (DT)
[ 0.044343][ T0] epc : trace_hardirqs_on+0x56/0xe2
[ 0.044601][ T0] ra : restore_all+0x12/0x6e
[ 0.044721][ T0] epc :
ffffffff80126a5c ra :
ffffffff80003b94 sp :
ffffffff81403db0
[ 0.044801][ T0] gp :
ffffffff8163acd8 tp :
ffffffff81414880 t0 :
0000000000000020
[ 0.044882][ T0] t1 :
0098968000000000 t2 :
0000000000000000 s0 :
ffffffff81403de0
[ 0.044967][ T0] s1 :
0000000000000000 a0 :
0000000000000001 a1 :
0000000000000100
[ 0.045046][ T0] a2 :
0000000000000000 a3 :
0000000000000000 a4 :
0000000000000000
[ 0.045124][ T0] a5 :
0000000000000000 a6 :
0000000000000000 a7 :
0000000054494d45
[ 0.045210][ T0] s2 :
ffffffff80003b94 s3 :
ffffffff81a8f1b0 s4 :
ffffffff80e27b50
[ 0.045289][ T0] s5 :
ffffffff81414880 s6 :
ffffffff8160fa00 s7 :
00000000800120e8
[ 0.045389][ T0] s8 :
0000000080013100 s9 :
000000000000007f s10:
0000000000000000
[ 0.045474][ T0] s11:
0000000000000000 t3 :
7fffffffffffffff t4 :
0000000000000000
[ 0.045548][ T0] t5 :
0000000000000000 t6 :
ffffffff814aa368
[ 0.045620][ T0] status:
0000000200000100 badaddr:
00000000000000f8 cause:
000000000000000d
[ 0.046402][ T0] [<
ffffffff80003b94>] restore_all+0x12/0x6e
This because the $fp(aka. $s0) register is not used as frame pointer in the
assembly entry code.
resume_kernel:
REG_L s0, TASK_TI_PREEMPT_COUNT(tp)
bnez s0, restore_all
REG_L s0, TASK_TI_FLAGS(tp)
andi s0, s0, _TIF_NEED_RESCHED
beqz s0, restore_all
call preempt_schedule_irq
j restore_all
To fix above issue, here we add one extra level wrapper for function
trace_hardirqs_{on,off}() so they can be safely called by low level entry
code.
Signed-off-by: Changbin Du <changbin.du@gmail.com>
Fixes:
3c4697982982 ("riscv: Enable LOCKDEP_SUPPORT & fixup TRACE_IRQFLAGS_SUPPORT")
Cc: stable@vger.kernel.org
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Damien Le Moal [Wed, 9 Feb 2022 03:56:23 +0000 (12:56 +0900)]
riscv: fix nommu_k210_sdcard_defconfig
Instead of an arbitrary delay, use the "rootwait" kernel option to wait
for the mmc root device to be ready.
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Fixes:
7e09fd3994c5 ("riscv: Add Canaan Kendryte K210 SD card defconfig")
Cc: stable@vger.kernel.org
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Daniel Bristot de Oliveira [Sun, 20 Feb 2022 22:49:57 +0000 (23:49 +0100)]
tracing: Dump stacktrace trigger to the corresponding instance
The stacktrace event trigger is not dumping the stacktrace to the instance
where it was enabled, but to the global "instance."
Use the private_data, pointing to the trigger file, to figure out the
corresponding trace instance, and use it in the trigger action, like
snapshot_trigger does.
Link: https://lkml.kernel.org/r/afbb0b4f18ba92c276865bc97204d438473f4ebc.1645396236.git.bristot@kernel.org
Cc: stable@vger.kernel.org
Fixes:
ae63b31e4d0e2 ("tracing: Separate out trace events from global variables")
Reviewed-by: Tom Zanussi <zanussi@kernel.org>
Tested-by: Tom Zanussi <zanussi@kernel.org>
Signed-off-by: Daniel Bristot de Oliveira <bristot@kernel.org>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Linus Torvalds [Fri, 25 Feb 2022 01:35:22 +0000 (17:35 -0800)]
Merge tag 'clk-fixes-for-linus' of git://git./linux/kernel/git/clk/linux
Pull clk fixes from Stephen Boyd:
"A couple driver fixes in the clk subsystem
- Fix a hang due to bad clk parent in the Ingenic jz4725b driver
- Fix SD controllers on Qualcomm MSM8994 SoCs by removing clks that
shouldn't be touched"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: jz4725b: fix mmc0 clock gating
clk: qcom: gcc-msm8994: Remove NoC clocks
Linus Torvalds [Fri, 25 Feb 2022 01:29:26 +0000 (17:29 -0800)]
Merge tag 'drm-fixes-2022-02-25' of git://anongit.freedesktop.org/drm/drm
Pull drm fixes from Dave Airlie:
"Regular drm fixes pull, i915, amdgpu and tegra mostly, all pretty
small.
core:
- edid: Always set RGB444
tegra:
- tegra186 suspend/resume fixes
- syncpoint wait fix
- build warning fix
- eDP on older devices fix
amdgpu:
- Display FP fix
- PCO powergating fix
- RDNA2 OEM SKU stability fixes
- Display PSR fix
- PCI ASPM fix
- Display link encoder fix for TEST_COMMIT
- Raven2 suspend/resume fix
- Fix a regression in virtual display support
- GPUVM eviction fix
i915:
- Fix QGV handling on ADL-P+
- Fix bw atomic check when switching between SAGV vs. no SAGV
- Disconnect PHYs left connected by BIOS on disabled ports
- Fix SAVG to no SAGV transitions on TGL+
- Print PHY name properly on calibration error (DG2)
imx:
- dcss: Select GEM CMA helpers
radeon:
- Fix some variables's type
vc4:
- Fix codec cleanup
- Fix PM reference counting"
* tag 'drm-fixes-2022-02-25' of git://anongit.freedesktop.org/drm/drm: (24 commits)
drm/amdgpu: check vm ready by amdgpu_vm->evicting flag
drm/amdgpu: bypass tiling flag check in virtual display case (v2)
Revert "drm/amdgpu: add modifiers in amdgpu_vkms_plane_init()"
drm/amdgpu: do not enable asic reset for raven2
drm/amd/display: Fix stream->link_enc unassigned during stream removal
drm/amd: Check if ASPM is enabled from PCIe subsystem
drm/edid: Always set RGB444
drm/tegra: dpaux: Populate AUX bus
drm/radeon: fix variable type
drm/amd/display: For vblank_disable_immediate, check PSR is really used
drm/amd/pm: fix some OEM SKU specific stability issues
drm/amdgpu: disable MMHUB PG for Picasso
drm/amd/display: Protect update_bw_bounding_box FPU code.
drm/i915/dg2: Print PHY name properly on calibration error
drm/i915: Fix bw atomic check when switching between SAGV vs. no SAGV
drm/i915: Correctly populate use_sagv_wm for all pipes
drm/i915: Disconnect PHYs left connected by BIOS on disabled ports
drm/i915: Widen the QGV point mask
drm/imx/dcss: i.MX8MQ DCSS select DRM_GEM_CMA_HELPER
drm/vc4: crtc: Fix runtime_pm reference counting
...
Linus Torvalds [Thu, 24 Feb 2022 22:36:38 +0000 (14:36 -0800)]
Merge tag 'perf-tools-fixes-for-v5.17-2022-02-24' of git://git./linux/kernel/git/acme/linux
Pull perf tools fixes from Arnaldo Carvalho de Melo:
- Fix double free in in the error path when opening perf.data from
multiple files in a directory instead of from a single file
- Sync the msr-index.h copy with the kernel sources
- Fix error when printing 'weight' field in 'perf script'
- Skip failing sigtrap test for arm+aarch64 in 'perf test'
- Fix failure to use a cpu list for uncore events in hybrid systems,
e.g. Intel Alder Lake
* tag 'perf-tools-fixes-for-v5.17-2022-02-24' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux:
perf script: Fix error when printing 'weight' field
tools arch x86: Sync the msr-index.h copy with the kernel sources
perf data: Fix double free in perf_session__delete()
perf evlist: Fix failed to use cpu list for uncore events
perf test: Skip failing sigtrap test for arm+aarch64
Linus Torvalds [Thu, 24 Feb 2022 22:05:49 +0000 (14:05 -0800)]
Merge tag 'for-linus' of git://git./virt/kvm/kvm
Pull kvm fixes from Paolo Bonzini:
"x86 host:
- Expose KVM_CAP_ENABLE_CAP since it is supported
- Disable KVM_HC_CLOCK_PAIRING in TSC catchup mode
- Ensure async page fault token is nonzero
- Fix lockdep false negative
- Fix FPU migration regression from the AMX changes
x86 guest:
- Don't use PV TLB/IPI/yield on uniprocessor guests
PPC:
- reserve capability id (topic branch for ppc/kvm)"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: x86: nSVM: disallow userspace setting of MSR_AMD64_TSC_RATIO to non default value when tsc scaling disabled
KVM: x86/mmu: make apf token non-zero to fix bug
KVM: PPC: reserve capability 210 for KVM_CAP_PPC_AIL_MODE_3
x86/kvm: Don't use pv tlb/ipi/sched_yield if on 1 vCPU
x86/kvm: Fix compilation warning in non-x86_64 builds
x86/kvm/fpu: Remove kvm_vcpu_arch.guest_supported_xcr0
x86/kvm/fpu: Limit guest user_xfeatures to supported bits of XCR0
kvm: x86: Disable KVM_HC_CLOCK_PAIRING if tsc is in always catchup mode
KVM: Fix lockdep false negative during host resume
KVM: x86: Add KVM_CAP_ENABLE_CAP to x86
Linus Torvalds [Thu, 24 Feb 2022 21:19:57 +0000 (13:19 -0800)]
Merge tag 'pci-v5.17-fixes-5' of git://git./linux/kernel/git/helgaas/pci
Pull pci fixes from Bjorn Helgaas:
- Fix a merge error that broke PCI device enumeration on mvebu
platforms, including Turris Omnia (Armada 385) (Pali Rohár)
- Avoid using ATS on all AMD Navi10 and Navi14 GPUs because some
VBIOSes don't account for "harvested" (disabled) parts of the chip
when initializing caches (Alex Deucher)
* tag 'pci-v5.17-fixes-5' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: Mark all AMD Navi10 and Navi14 GPU ATS as broken
PCI: mvebu: Fix device enumeration regression
Linus Torvalds [Thu, 24 Feb 2022 20:45:32 +0000 (12:45 -0800)]
Merge tag 'net-5.17-rc6' of git://git./linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Including fixes from bpf and netfilter.
Current release - regressions:
- bpf: fix crash due to out of bounds access into reg2btf_ids
- mvpp2: always set port pcs ops, avoid null-deref
- eth: marvell: fix driver load from initrd
- eth: intel: revert "Fix reset bw limit when DCB enabled with 1 TC"
Current release - new code bugs:
- mptcp: fix race in overlapping signal events
Previous releases - regressions:
- xen-netback: revert hotplug-status changes causing devices to not
be configured
- dsa:
- avoid call to __dev_set_promiscuity() while rtnl_mutex isn't
held
- fix panic when removing unoffloaded port from bridge
- dsa: microchip: fix bridging with more than two member ports
Previous releases - always broken:
- bpf:
- fix crash due to incorrect copy_map_value when both spin lock
and timer are present in a single value
- fix a bpf_timer initialization issue with clang
- do not try bpf_msg_push_data with len 0
- add schedule points in batch ops
- nf_tables:
- unregister flowtable hooks on netns exit
- correct flow offload action array size
- fix a couple of memory leaks
- vsock: don't check owner in vhost_vsock_stop() while releasing
- gso: do not skip outer ip header in case of ipip and net_failover
- smc: use a mutex for locking "struct smc_pnettable"
- openvswitch: fix setting ipv6 fields causing hw csum failure
- mptcp: fix race in incoming ADD_ADDR option processing
- sysfs: add check for netdevice being present to speed_show
- sched: act_ct: fix flow table lookup after ct clear or switching
zones
- eth: intel: fixes for SR-IOV forwarding offloads
- eth: broadcom: fixes for selftests and error recovery
- eth: mellanox: flow steering and SR-IOV forwarding fixes
Misc:
- make __pskb_pull_tail() & pskb_carve_frag_list() drop_monitor
friends not report freed skbs as drops
- force inlining of checksum functions in net/checksum.h"
* tag 'net-5.17-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (85 commits)
net: mv643xx_eth: process retval from of_get_mac_address
ping: remove pr_err from ping_lookup
Revert "i40e: Fix reset bw limit when DCB enabled with 1 TC"
openvswitch: Fix setting ipv6 fields causing hw csum failure
ipv6: prevent a possible race condition with lifetimes
net/smc: Use a mutex for locking "struct smc_pnettable"
bnx2x: fix driver load from initrd
Revert "xen-netback: Check for hotplug-status existence before watching"
Revert "xen-netback: remove 'hotplug-status' once it has served its purpose"
net/mlx5e: Fix VF min/max rate parameters interchange mistake
net/mlx5e: Add missing increment of count
net/mlx5e: MPLSoUDP decap, fix check for unsupported matches
net/mlx5e: Fix MPLSoUDP encap to use MPLS action information
net/mlx5e: Add feature check for set fec counters
net/mlx5e: TC, Skip redundant ct clear actions
net/mlx5e: TC, Reject rules with forward and drop actions
net/mlx5e: TC, Reject rules with drop and modify hdr action
net/mlx5e: kTLS, Use CHECKSUM_UNNECESSARY for device-offloaded packets
net/mlx5e: Fix wrong return value on ioctl EEPROM query failure
net/mlx5: Fix possible deadlock on rule deletion
...
Dave Airlie [Thu, 24 Feb 2022 19:51:04 +0000 (05:51 +1000)]
Merge tag 'drm-intel-fixes-2022-02-24' of git://anongit.freedesktop.org/drm/drm-intel into drm-fixes
- Fix QGV handling on ADL-P+ (Ville Syrjälä)
- Fix bw atomic check when switching between SAGV vs. no SAGV (Ville Syrjälä)
- Disconnect PHYs left connected by BIOS on disabled ports (Imre Deak)
- Fix SAVG to no SAGV transitions on TGL+ (Ville Syrjälä)
- Print PHY name properly on calibration error (DG2) (Matt Roper)
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/YhdyHwRWkOTWwlqi@tursulin-mobl2