drm/i915: Keep plane->state updated on pageflip

Until all drivers have transitioned to atomic, the framebuffer
associated with a plane is tracked in both plane->fb (for legacy) and
plane->state->fb (for all the new atomic codeflow).  All of our modeset
and plane updates use drm_plane->update_plane(), so in theory plane->fb
and plane->state->fb should always stay in sync and point at the same
thing for i915.  However we forgot about the pageflip ioctl case, which
currently only updates plane->fb and leaves plane->state->fb at a stale
value.

Surprisingly, this doesn't cause any real problems at the moment since
internally we use the plane->fb pointer in most of the places that
matter, and on the next .update_plane() call, we use plane->fb to figure
out which framebuffer to cleanup.  However when we switch to the full
atomic helpers for update_plane()/disable_plane(), those helpers use
plane->state->fb to figure out which framebuffer to cleanup, so not
having updated the plane->state->fb pointer causes things to blow up
following a pageflip ioctl.

The fix here is to just make sure we update plane->state->fb at the same
time we update plane->fb in the pageflip ioctl.

Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Remove bogus locking check in the hangcheck code

You can _never_ assert that a lock is not held, except in some very
restricted corner cases where it's guranteed that your code is running
single-threade (e.g. driver load before you've published any pointers
leading to that lock).

In addition the early return breaks a bunch of testcases since with
highly concurrent hangcheck stress tests the reset fails to work and
the test doesn't recover and time out.

This regression has been introduced in

commit b8d24a06568368076ebd5a858a011699a97bfa42
Author: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Date:   Wed Jan 28 17:03:14 2015 +0200

    drm/i915: Remove nested work in gpu error handling

Aside: It is possible to check whether a given task doesn't hold a
lock, but only when lockdep is enabled, using the lockdep_assert_held
stuff.

Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=88908
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>

drm/i915: Update DRIVER_DATE to 20150130

Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Use pipe_config's cpu_transcoder for reading encoder hw state

The get_config() functions for ddi and dp_mst, used to read the value
of cpu_transcoder from the crtc->config instead of the state passed as
an argument. On the hardware state readout path, that happens to work
since the proper value is written to it before encoder->get_config() is
called. However, in the check_crtc() path, the state will be read from
the cpu_transcoder in the software tracking, instead of the one just
read out from hw. Using the field in the supplied intel_crtc_state
should do the right thing in both cases.

v2: Fix intel_ddi_get_config() too. (Ander)

Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Fix a use-after-free in intel_execlists_retire_requests

Remove request from list before unreferencing it, in case it's actually
the only reference. (Found by Tvrtko Ursulin)

This issue has been most likely introduced in

commit 6d3d8274bc45de4babb62d64562d92af984dd238
Author: Nick Hoath <nicholas.hoath@intel.com>
Date:   Thu Jan 15 13:10:39 2015 +0000

    drm/i915: Subsume intel_ctx_submit_request in to drm_i915_gem_request

Signed-off-by: Nick Hoath <nicholas.hoath@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Split shared dpll setup out of __intel_set_mode()

This simplifies __intel_set_mode() a little.

Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Don't do posting reads on getting forcewake

The checking for ack and also any subsequent mmio access
will serialize with setting the forcewake bit. Drop the
posting read as superfluous.

Note that in the put side we still want to keep the posting read
as it will ensure that the hw sees our forcewake release in a
timely manner and doesn't keep the hw powered up.

Comment from Chris:

On Wed, Jan 28, 2015 at 05:54:14PM +0200, Mika Kuoppala wrote:
> Ville Syrjälä <ville.syrjala@linux.intel.com> writes:
> > IIRC the posting read from same cache line actually fixed real bugs. So
> > I'm a bit worried about dropping them. But I suppose it's possible only
> > the _put side was important for those bugs.
>
> I found these:
>
> commit 6af2d180f82151cf3d58952e35a4f96e45bc453a
> Author: Daniel Vetter <daniel.vetter@ffwll.ch>
> Date:   Thu Jul 26 16:24:50 2012 +0200
>
>     drm/i915: fix forcewake related hangs on snb
>
> commit 8dee3eea3ccd3b6c00a8d3a08dd715d6adf737dd
> Author: Ben Widawsky <ben@bwidawsk.net>
> Date:   Sat Sep 1 22:59:50 2012 -0700
>
>     drm/i915: Never read FORCEWAKE
>
> https://bugs.freedesktop.org/show_bug.cgi?id=51738
> https://bugs.freedesktop.org/show_bug.cgi?id=52424
>
> The snb here seems to survive gem_dummy_reloc_loop and
> gem_ring_sync_loop in here with the get side posting removed.

Note that we kept the once associated with #52424, but judging by my
comments in #51738 the posting read is just a band aid anyway as a full
mb() itself was not adequate.

Suggested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: paste relevant review discussion in.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Do uncore early sanitize after domain init

intel_uncore_early_sanitize() will reset the forcewake registers. When
forcewake domains were introduced, the domain init was done after the
sanitization of the forcewake registers. And as the resetting of
registers use the domain accessors, we tried to reset the forcewake
registers with unitialized forcewake domains and failed.

Fix this by sanitizing after all the domains have been initialized. Do
per domain clearing of forcewake register on domain init so that
IVB can do early access to ECOBUS do determine the final configuration.

This regression was introduced in

commit 05a2fb157e44a53c79133805d30eaada43911941
Author: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Date:   Mon Jan 19 16:20:43 2015 +0200

    drm/i915: Consolidate forcewake code

v2: Carve out ellc detect, fw_domain_reset for ivb/ecobus (Chris)

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=88805
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reported-by: Olof Johansson <olof@lixom.net>
Tested-by: Darren Hart <dvhart@linux.intel.com> (v1)
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Handle CHV in vlv_set_rps_idle()

Move the CHV check into vlv_set_rps_idle() to simplify the caller a bit.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Remove nested work in gpu error handling

Now when we declare gpu errors only through our own dedicated
hangcheck workqueue there is no need to have a separate workqueue
for handling the resetting and waking up the clients as the deadlock
concerns are no more.

The only exception is i915_debugfs::i915_set_wedged, which triggers
error handling through process context. However as this is only used through
test harness it is responsibility for test harness not to introduce hangs
through both debug interface and through hangcheck mechanism at the same time.

Remove gpu_error.work and let the hangcheck work do the tasks it used to.

v2: Add a big warning sign into i915_debugfs::i915_set_wedged (Chris)

Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915/documentation: Add intel_uncore.c to drm.tmpl

Include intel_uncore.c in template for it to include d
documentation for intel_uncore_forcewake_get and *_put.

Cc: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915/dsi: remove intel_dsi_cmd.c and the unused functions therein

The removed functions can be resurrected in intel_dsi.c as need arises.

Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-By: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915/dsi: move dpi_send_cmd() to intel_dsi.c and make it static

No functional changes.

Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-By: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915/dsi: remove old read/write functions in favor of new stuff

All of these are replaced by the drm core mipi dsi functions.

Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-By: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915/dsi: make the vbt panel driver use mipi_dsi_device for transfers

Use the drm core interfaces in preparation of removing our homebrew.

Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-By: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915/dsi: add drm mipi dsi host support

Add basic support for using the drm mipi dsi framework for DSI. We don't
use device tree which is pretty much required by mipi_dsi_host_register
and friends, and we don't have the kind of device model the functions
expect either. So we cheat and use it as a library to abstract what we
need: a nice, clean interface for DSI transfers. This means we will have
to be careful with what functions we call, as the driver model devices
in mipi_dsi_host and mipi_dsi_device will *not* be initialized.

Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-By: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915/dsi: switch to drm_panel interface

Replace intel_dsi_device and intel_dsi_dev_ops with drm_panel and
drm_panel_funcs. They are adequate for what we have now, and if we end
up needing more than this we should improve drm_panel. This will keep us
better aligned with the drm core infrastructure.

The panel driver initialization changes a bit. It still remains hideous,
but fixing that is beyond the scope here.

v2: extend mode config mutex to cover drm_panel_get_modes (Shobhit)
    vbt_panel->intel_dsi = intel_dsi in vbt panel init (Shobhit)

Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-By: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915/skl: Enabling PSR on Skylake

Mainly taking care of some register offsets, otherwise things are similar to
hsw. Also, programming ddi aux to use hardcoded values for psr data select.

v2: introduce  EDP_PSR_AUX_BASE macro (Chris)
v3: Moving to HW tracking for SKL+ platforms, so activating source psr during
psr_enabling and then avoiding psr entries and exits for each frontbuffer
updates.
v4: Using SKL DDI AUX regs instead of changing PSR_AUX regs definition (Rodrigo)

Signed-off-by: Sonika Jindal <sonika.jindal@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
[danvet: Drop the hunks to short-circuit sw tracking: We'd need to
push this down one level, and I don't fully trust the test coverage
yet to do so. So much prefer we pick a whitelist approach for the
cases we know work correctly.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

Revert "drm/i915: Fix mutex->owner inspection race under DEBUG_MUTEXES"

The core fix was applied in

commit a63b03e2d2477586440741677ecac45bcf28d7b1
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date:   Tue Jan 6 10:29:35 2015 +0000

    mutex: Always clear owner field upon mutex_unlock()

(note the absence of stable@ tag)

so we can now revert our band-aid commit 226e5ae9e5f910 for -next.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Be consistent on printing seqnos

We have had %x and %u intermixed. Bring everything in line and
use %x

Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Display current hangcheck status in debugfs

For example,

/sys/kernel/debug/dri/0/i915_hangcheck_info:

Hangcheck active, fires in 15887800ms
render ring:
        seqno = -4059 [current -583]
        action = 2
        score = 0
        ACTHD = 1ee8 [current 21f980]
        max ACTHD = 0

v2: Include expiration ETA. Can anyone spot a problem?
v3: Convert for workqueued hangcheck (Mika)
v4: Print seqnos as unsigned ints (Ville)
v5: Print seqnos as hex (Chris)

Tested-By: PRC QA PRTS (Patch Regression Test System Contact: shuang.he@intel.com) (v2)
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> (v2)
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Convert hangcheck from a timer into a delayed work item

When run as a timer, i915_hangcheck_elapsed() must adhere to all the
rules of running in a softirq context. This is advantageous to us as we
want to minimise the risk that a driver bug will prevent us from
detecting a hung GPU. However, that is irrelevant if the driver bug
prevents us from resetting and recovering. Still it is prudent not to
rely on mutexes inside the checker, but given the coarseness of
dev->struct_mutex doing so is extremely hard.

Give in and run from a work queue, i.e. outside of softirq.

v2: Use own workqueue to avoid deadlocks (Daniel)
    Cleanup commit msg and add comment to i915_queue_hangcheck() (Chris)

Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Daniel Vetter <dnaiel.vetter@ffwll.chm>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> (v1)
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
[danvet: Remove accidental kerneldoc comment starter, to appease the 0
day builder.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

agp/intel: Serialise after GTT updates

An interesting bug occurs on Pineview through which the root cause is
that the writes of the PTE values into the GTT is not serialised with
subsequent memory access through the GTT (when using WC updates of the
PTE values). This is despite there being a posting read after the GTT
update. However, by changing the address of the posting read, the memory
access is indeed serialised correctly.

Whilst we are manipulating the memory barriers, we can remove the
compiler :memory restraint on the intermediate PTE writes knowing that
we explicitly perform a posting read afterwards.

v2: Replace posting reads with explicit write memory barriers - in
particular this is advantages in case of single page objects. Update
comments to mention this issue is only with WC writes.

Testcase: igt/gem_exec_big #pnv
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=88191
Tested-by: huax.lu@intel.com (v1)
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drivers: gpu: drm: i915: intel_fifo_underrun.c: Fix a typo in comment

The comment for intel_cpu_fifo_underrun_irq_handler() is not consistent
with the code and the rest of the comment for this routine. This patch
fixes this typo in comment.

Signed-off-by: Kumar Amit Mehta <gmate.amit@gmail.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Add i915.nuclear_pageflip command line param to force atomic (v4)

We don't have full atomic modeset support yet, but the "nuclear
pageflip" subset of functionality (i.e., plane operations only) should
be ready.  Allow the user to force atomic on for debug purposes, or for
fixed-purpose embedded devices that will only use atomic for plane
updates.

The term 'nuclear' is used here instead of 'atomic' to make it clear
that this doesn't allow full atomic modeset support, just a (very
useful) subset of the atomic functionality.

We'll drop the kernel parameter and unconditionally enable atomic in a
future patch once all of the necessary pieces are in.

v2:
 - Use module_param_named_unsafe() (Daniel)
 - Simplify comment on DRIVER_ATOMIC guard (Daniel)

v3:
 - Make the parameter "nuclear_pageflip" rather than just "nuclear"
   for clarity. (Ander)

v4:
 - Make the internal variable "nuclear_pageflip" as well as the
   command-line option. (Ander)

Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Switch plane properties to full atomic helper.

This will exercise our atomic pipeline for legacy property updates.

Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Add crtc state duplication/destruction functions

The atomic helpers need these to prepare a new state object when
starting a new atomic operation.

Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Add atomic_get_property entrypoint for connectors (v2)

Even though we only support atomic plane updates at the moment, we still
need to add an .atomic_get_property() entrypoint for connectors before
we allow the driver to flip on the DRIVER_ATOMIC bit.  As soon as that
bit gets set, the DRM core will start adding atomic connector properties
(in addition to the plane properties we care about at the moment), so we
need to be able to handle the new way the DRM core will interact with
us.

For simplicity, we just lookup driver-specific connector properties in
the usual shadow array maintained by the core.  Once we get real atomic
modeset support for crtc's and planes, this code should be re-written to
pull the data out of crtc/connector state structures.

v2: Fix intel_dvo and intel_dsi that I missed on the first pass (Ander)

Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Setup dummy atomic state for connectors (v3)

We want to enable/test plane updates via the atomic interface, but as
soon as we flip DRIVER_ATOMIC on, the DRM core will take some atomic
codepaths to lookup properties during drmModeGetConnector() and some of
those codepaths unconditionally dereference connector->state
(specifically when looking up the CRTC ID property in
drm_atomic_connector_get_property()).  Create a dummy connector state
for each connector at init time to ensure the DRM core doesn't try to
dereference a NULL connector->state.  The actual connector properties
will never be updated or contain useful information, but since we're
doing this specifically for testing/debug of the plane operations (and
only when a specific kernel module option is given), that shouldn't
really matter.

Once we start creating connector states, the DRM core will want to be
able to clean them up for us.  We also need to hook up the destruction
entrypoint to the core's helper.

v2: Squash in the patch to set the state destruction hook (Ander & Bob)

v3: Only create dummy connector states when we're actually faking
    atomic support.  (Ander)

Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Add main atomic entrypoints (v2)

Add the top-level atomic entrypoints for check/commit.  These won't get
called yet; we still need to either enable the atomic ioctl or switch to
using the non-transitional atomic helpers for legacy operations.

v2:
 - Use plane->pipe rather than plane->possible_crtcs while ensuring that
   only a single CRTC is in use.  Either way will work fine since i915
   drm_plane's are always tied to a single CRTC, but plane->pipe is
   slightly more intuitive. (Ander)
 - Simplify crtc/connector checking logic. (Ander)

Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Add .atomic_{get, set}_property() entrypoints to planes

When we flip on the DRIVER_ATOMIC bit, the DRM core will start calling
this entrypoint to set and lookup driver-specific plane property values,
rather than maintaining a shadow copy in object->properties.

Note that although we add these functions to the plane vtable, they will
not yet be called.  Future patches that switch our .set_property()
handler and/or enable full atomic functionality are required before
these code paths will be executed.

Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Consolidate plane handler vtables

All of the previous refactoring/consolidation of plane code has resulted
in intel_primary_plane_funcs, intel_cursor_plane_funcs, and
intel_sprite_plane_funcs being identical.  Replace all of these with a
single 'intel_plane_funcs' vtable for simplicity.

Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Move rotation from intel_plane to drm_plane_state

Runtime state that can be manipulated via properties should now go in
intel_plane_state/drm_plane_state so that it can be tracked as part of
an atomic transaction.

We add a new 'intel_create_plane_state' function so that the proper
initial value for this property (and future properties) doesn't have to
be repeated at each plane initialization site.

v2:
 - Stick rotation in common drm_plane_state rather than
   intel_plane_state. (Daniel)
 - Add intel_create_plane_state() to consolidate the places where we
   have to set initial state values.  (Ander)

Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Use intel_gpu_freq() and intel_freq_opcode()

Replace all the vlv_gpu_freq(), vlv_freq_opcode(),
*GT_FREQUENCY_MULTIPLIER, and /GT_FREQUENCY_MULTIPLIER instances
with intel_gpu_freq() and intel_freq_opcode() calls.

Most of the change was performed with the following semantic patch:
@@
expression E;
@@
(
- E * GT_FREQUENCY_MULTIPLIER
+ intel_gpu_freq(dev_priv, E)
|
- E *= GT_FREQUENCY_MULTIPLIER
+ E = intel_gpu_freq(dev_priv, E)
|
- E /= GT_FREQUENCY_MULTIPLIER
+ E = intel_freq_opcode(dev_priv, E)
|
- do_div(E, GT_FREQUENCY_MULTIPLIER)
+ E = intel_freq_opcode(dev_priv, E)
)

@@
expression E1, E2;
@@
(
- vlv_gpu_freq(E1, E2)
+ intel_gpu_freq(E1, E2)
|
- vlv_freq_opcode(E1, E2)
+ intel_freq_opcode(E1, E2)
)

@@
expression E1, E2, E3, E4;
@@
(
- if (IS_VALLEYVIEW(E1)) {
-  E2 = intel_gpu_freq(E3, E4);
- } else {
-  E2 = intel_gpu_freq(E3, E4);
- }
+ E2 = intel_gpu_freq(E3, E4);
|
- if (IS_VALLEYVIEW(E1)) {
-  E2 = intel_freq_opcode(E3, E4);
- } else {
-  E2 = intel_freq_opcode(E3, E4);
- }
+ E2 = intel_freq_opcode(E3, E4);
)

One hunk was manually undone as intel_gpu_freq() ended up
calling itself. Supposedly it would be possible to exclude
certain functions via !=~, but I couldn't get that to work.

Also the removal of vlv_gpu_freq() and vlv_opcode_freq() compat
wrappers was done manually.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Add intel_gpu_freq() and intel_freq_opcode()

Rename the vlv_gpu_freq() and vlv_freq_opecode() functions to have
an intel_ prefix, and handle non-VLV/CHV platforms in them as well.
Leave the vlv_ names around for now since they're currently used.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Add gt_act_freq_mhz sysfs file

Currently the 'gt_cur_freq_mhz' file shows the actual GPU frequency on
VLV/CHV, and the last requested frequency on other platforms. Change the
meaning of the file on VLV/CHV to follow the the other platforms, and
introduce a new file 'gt_act_freq_mhz' which shows the actual frequency
on all platforms.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Update PMINTRMSK on VLV/CHV after sysfs min/max freq change

Currently we don't call valleyview_set_rps() when changing the min/max
limits through sysfs if the current frequency is still within the new
limits. However that means we sometimes forget to update PMINTRMSK.
Eg. if the current frequency is at the old minimum, and then we reduce
the minum further we should then enable the 'down' interrupts in PMINTRMSK
but currently we don't.

Fix it up by always calling valleyview_set_rps() (just like we do for
!vlv/chv platforms). This also allows the code to be simplified a bit.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: DRRS calls based on frontbuffer

Calls have been added to invalidate/flush DRRS whenever invalidate/flush is
called as part of frontbuffer tracking.
Apart from calls as a result of GEM tracking to fb invalidate/flush, a
call has been added to invalidate fb obj from crtc_page_flip as well. This
is to track busyness through flip calls.
The call to fb_obj_invalidate (in flip) is placed before queuing flip for this
obj.

drrs_invalidate() and drrs_flush() check for drrs.dp which would be NULL if
it was setup in drrs_enable(). This covers for the condition when DRRS is
not supported.

v2: Removing the call to invalidate_drrs from page_flip.
This has not been tested on Android yet, but, in case DRRS transtions do not
work as expected, check by adding back this call in page_flip.

Signed-off-by: Vandana Kannan <vandana.kannan@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Enable/disable DRRS

Calling enable/disable DRRS when enable/disable DDI are called.
These functions are responsible for setup of drrs data (in enable) and
reset of drrs (in disable).
has_drrs is true when downclock_mode is found and SEAMLESS_DRRS is set in
the VBT. A check has been added for has_drrs in these functions, to make
sure the functions go through only if DRRS will work on the platform with
the attached panel.

V2: [By Ram]: WARN_ON is used when intel_edp_drrs_enable() is called more than
once [Rodrigo]

Signed-off-by: Vandana Kannan <vandana.kannan@intel.com>
Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Initialize DRRS delayed work

Add DRRS work function to trigger a switch to low refresh rate,
when no activity is detected on screen till 1 sec duration.

v2: [By Ram]: drrs.dp also protected with drrs.mutex and worker function
is renamed to intel_edp_drrs_downclock_work [Chris]

Signed-off-by: Vandana Kannan <vandana.kannan@intel.com>
Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Use symbolic irqreturn for ->hpd_pulse

Self-explanatory code is better code.

Cc: Dave Airlie <airlied@redhat.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915/dsi: add some constness to vbt panel driver

Const is good for you. No functional changes.

Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-By: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915/dsi: remove unnecessary dsi device callbacks

Remove all the trivial and/or dummy callbacks from intel dsi device
ops. Merge send_otp_cmds into panel_reset as they're called back to
back.

This will be helpful for switching to use drm_panel for the
callbacks. If we ever need the additional callbacks, we should add them
to drm_panel funcs.

Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-By: Shobhit Kumar <shobhit.kumar@intel.com>
[danvet: Resolve tiny conflict with ongoing atomic work.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915/dsi: call wait_for_dsi_fifo_empty() for each dsi port

Add port parameter to wait_for_dsi_fifo_empty, and call it for each dsi
port.

We can now remove the transitional intel_dsi_pipe_to_port() function.

Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-By: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915/dsi: move wait_for_dsi_fifo_empty to intel_dsi.c

wait_for_dsi_fifo_empty can be static in intel_dsi.c. No functional
changes.

Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-By: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915/dsi: set max return packet size for each dsi port

This seems like the right thing to do. This also gets rid of a call to
intel_dsi_pipe_to_port() which we want to remove eventually.

v2: add braces to fix else logic (Shobhit)

Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-By: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915/dsi: call dpi_send_cmd() for each dsi port at a higher level

Instead of having the for each dsi port loop within dpi_send_cmd(), add
a port parameter to the function and call it for each port instead.

This is a rewrite of

commit 4510cd779e5897eeb8691aecbd639bb62ec27d55
Author: Gaurav K Singh <gaurav.k.singh@intel.com>
Date:   Thu Dec 4 10:58:51 2014 +0530

    drm/i915: Dual link needs Shutdown and Turn on packet for both ports

to add more flexibility in using dpi_send_cmd() for just one port as
necessary. No functional changes.

Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-By: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Change VLV WIZ hashing mode to 16x4

We set the WIZ hashing mode to 16x4 for all the other gen6+
platfotrms, so let's follow suit on VLV.

My VLV is AWOL currently so I didn't test this, but since the results
for all the other platforms agree that 16x4 is the fastest we might
assume the same holds for VLV.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Arun Siluvery <arun.siluvery@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Change CHV WIZ hashing mode to 16x4

I ran a few tests with xonotic and synmark2 trying out the
different WIZ hashing modes on CHV. The results seem to match the
results I got with IVB/HSW when I did the similar tests on them
in the past. That is 16x4 is generally the fastest mode, 8x8 comes
next and finally 8x4. On CHV the difference between the modes is
at most ~1% in most tests. IIRC on IVB/HSW the difference was a little
bigger, but as there doesn't seem to be any real downside to 16x4
let's use it by default.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Arun Siluvery <arun.siluvery@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Drop some more CHV pre-production workarounds

Drop WaDisablePwrmtrEvent:chv as it's no longer needed.

Also remove the WaSetMaskForGfxBusyness:chv note, but we still
leave the GEN6_RP_MEDIA_IS_GFX bit enabled as that's still the
recommended setting.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Arun Siluvery <arun.siluvery@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Implement Wa4x4STCOptimizationDisable:chv

Wa4x4STCOptimizationDisable got only implemented for BDW, but according
to the w/a database CHV needs it too, so add it.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Arun Siluvery <arun.siluvery@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Simplify flush_cpu_write_domain

We can push down the decision whether to force flushing into the
implementation since in all places that matter obj->pin_display is
accurate already. The only place where the optimization really matters
is the sw_finish_ioctl, and that already checks for obj->pin_display
on its own.

I suspect that this was simply an artifact of how

commit 2c22569bba8af6c2976d5f9479fe54a53a39966b
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date:   Fri Aug 9 12:26:45 2013 +0100

    drm/i915: Update rules for writing through the LLC with the cpu

evolved - only v2 added the pin_display tracking.

Note that we still retain the gist of this logic from the above commit
with the explicit force argument for the low-level clflush function.

Ville noted in his review that there's a slight behavioural change in
the set_to_gtt_domain function, which now also will flush display
plane data. This opens-open the potential for userspace to start doing
buggy things by omitting the sw_finish_ioctl, which is why I've
rejected a functional equivalent patch from Ville a while ago:

http://lists.freedesktop.org/archives/intel-gfx/2013-November/036421.html

But on second consideration it's not that evil, and in any case the
justification here is more clarity, not allowing crazy userspace.

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Use sizeof(*fb) not sizeof(struct ...) in get_initial_plane_config()

Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Fix kzalloc() smatch warnings in get_initial_plane_config()

Smatch doesn't like:

  struct drm_framebuffer *fb;
  fb = kzalloc(sizeof(struct intel_framebuffer), GFP_KERNEL);

and warns with:

  warn: struct type mismatch 'drm_framebuffer vs intel_framebuffer'

This implicit cast was correct as struct intel_framebuffer has struct
drm_framebuffer as its first member, but in case someone want to reorder
the fields for some reason, it's slightly safer to access the underlying
drm_framebuffer through intel_fb->base.

Also, having fewer static analysis warnings is a worthy goal.

Cc: kbuild@01.org
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Performed deferred clflush inside set-cache-level

Currently we are hitting the WARN inside
i915_gem_object_set_cache_level() as we can now have an unbound object
in the GTT write domain (due to 43566dedde54f9 "drm/i915: Broaden
application of set-domain(GTT)"). To avoid the warning, we need to track
when we elided the clflush on a cacheable object and then evict the
cache for the object when we move the object out of a cacheable domain.

Reported-by: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Jani Nikula <jani.nikula@intel.com>
Testcase: igt/gem_mmap_wc/set-cache-level
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=88607
Tested-by: huax.lu@intel.com
[danvet: Split if into nested if as discussion on the m-l.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Rename unpin_count to pin_count

We increase it when we pin, so for the casual reader
rename it to cause less confusion.

Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Thomas Daniel <thomas.daniel@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Balance context pinning on reset cleanup

We pin when we submit to execlist queue. Balance
the pinning when the submitted queue is cleaned on reset.

Cc: Dave Gordon <david.s.gordon@intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Thomas Daniel <thomas.daniel@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: add I915_PARAM_HAS_BSD2 to i915_getparam

This will let userland only try to use the new ring
when the appropriate kernel is present

v2: change the number to be consistent with upstream (Zhipeng)

Signed-off-by: Zhipeng Gong <zhipeng.gong@intel.com>
Reviewed--by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Specify bsd rings through exec flag

On Skylake GT3 we have 2 Video Command Streamers (VCS), which is asymmetrical.
For example, HEVC GPU commands can be only dispatched to VCS1 ring.
But userspace has no control when using VCS1 or VCS2. This patch introduces
a mechanism to avoid the default ping-pong mode and use one specific ring
through execution flag. This mechanism is usable for all the platforms
with 2 VCS rings.

The open source usage is from these two commits in vaapi/intel:
commit 702050f04131a44ef8ac16651708ce8a8d98e4b8
Author: Zhao, Yakui <yakui.zhao@intel.com>
Date:   Mon Nov 17 12:44:19 2014 +0800

    Allow the batchbuffer to be submitted with override flag

commit a56efcdf27d11ad9b21664b4a2cda72d7f90f5a8
Author: Zhao Yakui <yakui.zhao@intel.com>
Date:   Mon Nov 17 12:44:22 2014 +0800

    Add the override flag to assure that HEVC video command
always uses BSD ring0 for SKL GT3 machine

v2: fix whitespace (Rodrigo)
v3: remove incorrect chunk that came on -collector rebase. (Rodrigo)
v4: change the comment (Zhipeng)
v5: address Daniel's comment (Zhipeng)

Signed-off-by: Zhipeng Gong <zhipeng.gong@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Rename plane_config to initial_plane_config

This vfunc and related structure are only used for fast boot, so let's
rename them to not take them as general purpose ones.

v2: Fix conflicts caused by the introduction of struct intel_crtc_state

Reviewed-By: Tvrtko Ursulin <tvrtko.ursulin@intel.com> (v1)
Suggested-by: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915/skl: Provide a Skylake version of get_plane_config()

Universal planes have changed a bit the register organization.

v2: Rebase on top of the latest drm-intel-nightly

v3: Use PLANE_SIZE to retrieve the fb size (Tvrtko)
    Don't use BUG() (Tvrtko)

v4: Use MISSING_CASE (Daniel)

Reviewed-By: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915/skl: intel_format_to_fourcc() doesn't work for SKL planes

We will have a skl_ version shortly!

Reviewed-By: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Make intel_format_to_fourcc() static

v2: Fix conflict caused by the introduction of struct intel_crtc_state

Reviewed-By: Tvrtko Ursulin <tvrtko.ursulin@intel.com> (v1)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Use pipe_name() in the get_plane_config() functions

We may as well try to be consistent everywhere and know the pipes by
their name.

Reviewed-By: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Don't use crtc->plane in ILK+ get_config()

crtc->plane can only be different from crtc->pipe pre-Gen4. Don't use it
in new-ish code.

Reviewed-By: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Unclutter the get_plane() functions

crtc->base.primary->fb was used everywhere. Use fb to temporarily point
there and don't forget to assign fb to its final destination at the end.

v2: Rebase on top of misc changes (mask of DSPSURF, PAGE_ALIGN)

Reviewed-By: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Use a common function for computing the fb height alignment

If we need to change the fb height constraints, it sounds like a good
idea to have to do it in one place only.

v2: v2: Rebase on top of Ander's "Make intel_crtc->config a pointer"

Reviewed-By: Tvrtko Ursulin <tvrtko.ursulin@intel.com> (v1)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Change plane_config to store a tiling_mode

Rather than having "tiled" meaning "is it X-tiled?" convert the field to
explicitely store the tiling mode. The code doesn't have to change much
as 1 is conveniently I915_TILING_X.

This is to accommodate future changes around tiling modes and scannout
buffers.

v2: Rebase on top of Ander's "Make intel_crtc->config a pointer"

Reviewed-By: Tvrtko Ursulin <tvrtko.ursulin@intel.com> (v1)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915/skl: Gen9 coarse power gating

Enable coarse power gating for Gen9. This feature allows render and
media engine to enter RC6 independently. Policies are configured
together with RC6. This feature will only be enabled when RC6 is
enabled.

v2: Rebase after Chris'/Mika's forcewake change (Damien)

Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Zhe Wang <zhe1.wang@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915/skl: Retrieve the frequency limits

v2: Use the new function, gen6_init_rps_frequencies() (Damien)

Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com> (v1)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915/skl: add turbo support

Per latest PM programming guide.

v2: the wrong flavour of the function updating the ring frequency was
    called, leading to dead locks (Tvrtko)

v3: Add GEN6_RP_MEDIA_IS_GFX to RP_CONTROL (Imre, done by Damien)

Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
[danvet: Fixup conflicts with Mika's forcewake refactor.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915/skl: Adding power domains for AUX controllers

Adding new power doamins for AUX controllers

v2: Added new power domains in power_domain_str per Imre's comment

v3: Added AUX power domains to older platforms

v4: Rebase on top of POWER_DOMAIN_PLLS.

v5: Modified to address review comments from Imre

Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Satheeshakrishna M <satheeshakrishna.m@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com> (v3)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Rename i915_gen6_forcewake_count_info

There are multiple forcewake domains in newer architectures.
Rename 'i915_gen6_forcewake_count_info' debugfs entry to
'i915_forcewake_domains' to reflect this.

Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Enum forcewake domains and domain identifiers

Make the domains and domain identifiers enums. To emphasize
the difference in order to avoid mistakes.

v2: s/fw_domain/forcewake_domain (Jani)
v3: rebase

Suggested-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Deepak S <deepak.s@linux.intel.com> (v1)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Rename the forcewake get/put functions

We have multiple forcewake domains now on recent gens. Change the
function naming to reflect this.

v2: More verbose names (Chris)
v3: Rebase
v4: Rebase
v5: Add documentation for forcewake_get/put

Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Deepak S <deepak.s@linux.intel.com> (v2)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Make vlv and chv forcewake put generic.

These two were using a fw dance logic where posting read was done
after both domain bit were set. When in other gens, the posting
read is done immediately after setting the forcewake bit for each
domain.

Now bring these in line with other gens.

Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Consolidate forcewake code

As we now have forcewake domains, take advantage of it
by putting the differences in gen fw handling in data rather
than in code.

In past we have opencoded this quite extensively as the fw handling
is in the fast path. There has also been a lot of cargo-culted
copy'n'pasting from older gens to newer ones.

Now when the releasing of the forcewake is done by deferred timer,
it gives chance to consolidate more. Due to the frequency of actual hw
access being significantly less.

Take advantage of this and generalize the fw handling code
as much as possible. But we still aim to keep the forcewake sequence
particularities for each gen intact. So the access pattern
to fw engines should remain the same.

v2: - s/old_ack/clear_ack (Chris)
    - s/post_read/posting_read (Chris)
    - less polite commit msg (Chris)

v3: - rebase
    - check and clear wake_count in init

v4: - fix posting reads for gen8 (PRTS)

Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Deepak S <deepak.s@linux.intel.com> (v2)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Reduce duplicated forcewake logic

Introduce a structure to track the individual forcewake domains and use
that to eliminate duplicate logic.

v2: - Rebase on latest dinq (Mika)
    - for_each_fw_domain macro (Mika)
    - Handle reset atomically, keeping the timer running (Mika)
    - for_each_fw_domain parameter ordering (Chris)
    - defer timer on new register access (Mika)

v3: - Fix forcewake_reset/get race by waiting pending timers

v4: - cond_resched and verbose warning on timer deletion (Chris)
    - need to run pending timers manually on reset

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> (v1)
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Acked-by: Deepak S <deepak.s@linux.intel.com> (v2)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Skip uncore lock on earlier gens

With gen < 6 we don't need to take uncore lock as we
don't have anything to protect from concurrent access.

v2: rebase and account for gen9 changes

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> (v1)
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Assert that runtime pm is active on user fw access

On user forcewake access, assert that runtime pm reference is held.
Fix and cleanup the callsites accordingly.

v2: Remove intel_runtime_pm_get() rebasehap (Deepak)

v3: use drivers own runtime state tracking as pm_runtime_active()
    will return wrong results when we are in resume callchain (Mika)

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Deepak S <deepak.s@linux.intel.com> (v2)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Rebalance runtime pm vs forcewake

Calling intel_runtime_pm_put() is illegal from a soft-irq context, so
revert the crude hack

commit aa0b3b5bb8768c1a6a6788869d9c7015eae7e80c
Author: Paulo Zanoni <paulo.r.zanoni@intel.com>
Date:   Tue Apr 1 14:55:07 2014 -0300

    drm/i915: don't schedule force_wake_timer at gen6_read

and apply the single line corrective instead.

v2: assert forcewake is off after the forcewake_reset (Paulo)

References: https://bugs.freedesktop.org/show_bug.cgi?id=80913
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Deepak S <deepak.s@linux.intel.com> (v1)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Subsume intel_ctx_submit_request in to drm_i915_gem_request

Move all remaining elements that were unique to execlists queue items
in to the associated request.

Issue: VIZ-4274

v2: Rebase. Fixed issue of overzealous freeing of request.
v3: Removed re-addition of cleanup work queue (found by Daniel Vetter)
v4: Rebase.
v5: Actual removal of intel_ctx_submit_request. Update both tail and postfix
pointer in __i915_add_request (found by Thomas Daniel)
v6: Removed unrelated changes

Signed-off-by: Nick Hoath <nicholas.hoath@intel.com>
Reviewed-by: Thomas Daniel <thomas.daniel@intel.com>
[danvet: Reformat comment with strange linebreaks.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Remove FIXME_lrc_ctx backpointer

The first pass implementation of execlists required a backpointer to the context to be held
in the intel_ringbuffer. However the context pointer is available higher in the call stack.
Remove the backpointer from the ring buffer structure and instead pass it down through the
call stack.

v2: Integrate this changeset with the removal of duplicate request/execlist queue item members.
v3: Rebase
v4: Rebase. Remove passing of context when the request is passed.

Signed-off-by: Nick Hoath <nicholas.hoath@intel.com>
Reviewed-by: Thomas Daniel <thomas.daniel@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Removed duplicate members from submit_request

Where there were duplicate variables for the tail, context and ring (engine)
in the gem request and the execlist queue item, use the one from the request
and remove the duplicate from the execlist queue item.

Issue: VIZ-4274

v1: Rebase
v2: Fixed build issues. Keep separate postfix & tail pointers as these are
used in different ways. Reinserted missing full tail pointer update.

Signed-off-by: Nick Hoath <nicholas.hoath@intel.com>
Reviewed-by: Thomas Daniel <thomas.daniel@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: execlist request keeps ptr/ref to gem_request

Add a reference and pointer from the execlist queue item to the associated
gem request. For execlist requests that don't have a request, create one
as a placeholder.

Issue: VIZ-4274
v1: Rebase after upstream of "Replace seqno values with request structures" patchset.

Signed-off-by: Nick Hoath <nicholas.hoath@intel.com>
Reviewed-by: Thomas Daniel <thomas.daniel@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Keep drm_crtc->state in sync with intel_crtc->config

So that atomic operations will reference the right crtc state.

Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Improve how the memory for crtc state is allocated

The previous patch changed the config field in intel_crtc to a pointer,
but to keep the mechanical changes (done with spatch) separate from the
new code, the pointer was made to point to a new _config field with type
struct intel_crtc_state added to that struct. This patch improves that
code by getting rid of that field, allocating a state struct in
intel_crtc_init() a keeping it properly updated when a mode set
happens.

v2: Manual changes split from previous patch. (Matt)
    Don't leak the current state when the crtc is destroyed (Matt)

Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
[danvet: Squash in fixup from Matt Roper for driver unload.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Make intel_crtc->config a pointer

To match the semantics of drm_crtc->state, which this will eventually
become. The allocation of the memory for config will be fixed in a
followup patch. By adding the extra _config field to intel_crtc it was
possible to generate this entire patch with the cocci script below.

@@ @@
struct intel_crtc {
...
-struct intel_crtc_state config;
+struct intel_crtc_state _config;
+struct intel_crtc_state *config;
...
}
@@ struct intel_crtc *crtc; @@
-memset(&crtc->config, 0, sizeof(crtc->config));
+memset(crtc->config, 0, sizeof(*crtc->config));
@@ @@
__intel_set_mode(...) {
<...
-to_intel_crtc(crtc)->config = *pipe_config;
+(*(to_intel_crtc(crtc)->config)) = *pipe_config;
...>
}
@@ @@
intel_crtc_init(...) {
...
WARN_ON(drm_crtc_index(&intel_crtc->base) != intel_crtc->pipe);
+intel_crtc->config = &intel_crtc->_config;
return;
...
}
@@ struct intel_crtc *crtc; @@
-&crtc->config
+crtc->config
@@ struct intel_crtc *crtc; identifier member; @@
-crtc->config.member
+crtc->config->member
@@ expression E; @@
-&(to_intel_crtc(E)->config)
+to_intel_crtc(E)->config
@@ expression E; identifier member; @@
-to_intel_crtc(E)->config.member
+to_intel_crtc(E)->config->member

v2: Clarify manual changes by splitting them into another patch. (Matt)
    Improve cocci script to generate even more of the changes. (Ander)

Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Use local pipe_config varariable when available

In functions that define a local pipe_config variable to point to
crtc->config, replace remaining references to crtc->config with
the local variable. This makes the code more consistent and easier
to change in an automated manner.

Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Pass new_config down do crtc_compute_clock

This reduces the number of direct users of crtc->new_config, opening up
the possibilty of removing it altogether.

Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Embedded struct drm_crtc_state in intel_crtc_state

And get rid of the duplicate mode structures. This patch was generated
with the following semantic patch:

@@ @@
struct intel_crtc_state {
+struct drm_crtc_state base;
+
...
-struct drm_display_mode requested_mode;
-struct drm_display_mode adjusted_mode;
...
}
@@ struct intel_crtc_state *state; @@
-state->adjusted_mode
+state->base.adjusted_mode
@@ struct intel_crtc_state *state; @@
-state->requested_mode
+state->base.mode
@@ struct intel_crtc_state state; @@
-state.adjusted_mode
+state.base.adjusted_mode
@@ struct intel_crtc_state state; @@
-state.requested_mode
+state.base.mode
@@ struct drm_crtc *crtc; @@
-to_intel_crtc(crtc)->config.adjusted_mode
+to_intel_crtc(crtc)->config.base.adjusted_mode
@@ identifier member; expression E; @@
-PIPE_CONF_CHECK_FLAGS(adjusted_mode.member, E);
+PIPE_CONF_CHECK_FLAGS(base.adjusted_mode.member, E);
@@ identifier member; @@
-PIPE_CONF_CHECK_I(adjusted_mode.member);
+PIPE_CONF_CHECK_I(base.adjusted_mode.member);
@@ identifier member; @@
-PIPE_CONF_CHECK_CLOCK_FUZZY(adjusted_mode.member);
+PIPE_CONF_CHECK_CLOCK_FUZZY(base.adjusted_mode.member);

v2: Completely generate the patch with cocci. (Ander)

Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Rename struct intel_crtc_config to intel_crtc_state

The objective is to make this structure usable with the atomic helpers,
so let's start with the rename. Patch generated with coccinelle:

@@ @@
-struct intel_crtc_config {
+struct intel_crtc_state {
...
}
@@ @@
-struct intel_crtc_config
+struct intel_crtc_state

v2: Completely generate the patch with cocci. (Ander)

Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Modifying structures related to DRRS

Earlier, DRRS structures were specific to eDP (used only in intel_dp).
Since DRRS can be extended to other internal display types
(if the panel supports multiple RR), modifying structures
to be part of drm_i915_private and have a provision to add display related
structs like intel_dp.
Also, aligning with frontbuffer tracking mechanism, the new structure
contains data for busy frontbuffer bits.

Signed-off-by: Vandana Kannan <vandana.kannan@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Rename 'reg' to 'clk_reg' to unconfuse it from the other 'reg'

On VLV/CHV the rc6 residency calculations read a second register to
determine the actual units used for the residency value. The variable
name 'reg' where that register value is stored shadows the function
argument 'reg'. That can easily leave the reader utterly confused, so
rename the internal variable to 'clk_reg'.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Deepak S<deepak.s@intel.com>
[danvet: Spellfix in commit message.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Drop VLV checks from rc6p and rc6pp sysfs files

We don't register the rc6p and rc6pp sysfs files on VLV, so there's no
point in having any VLV checks in them. Drop the checks.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Deepak S<deepak.s@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

Revert "Revert "drm/i915/chv: Use timeout mode for RC6 on chv""

The performance regression from the CHV RC6 EI->TO change is now fixed
so re-enable TO mode for better RC6 resicency.

This reverts commit e85a5c7989c5be8fe30acc35eba9fb54b3450f36.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S<deepak.s@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Configure GEN6_RP_DOWN_TIMEOUT on CHV

CherryViewA0_iGfx_BIOS_DRIVER_PUNIT_spec_y14w28d5 tells us not to enable
the RP down timeout interrupt, and says that the timeout value is hence
not used. We do enable that interrupt currently though, so leaving the
timeout as 0 results in very poor performance as the GPU frequency keeps
dropping constantly. So just program the register with the recommended
value.

Leaving the interrupt enabled doesn't seem to do any harm so far. So
I've decided to leave it on for now, just to avoid making CHV a
special case.

This fixes the performance regression from:
 commit 5a0afd4b78ec23f27f5d486ac3d102c2e8d66bd7
 Author: Deepak S <deepak.s@linux.intel.com>
 Date:   Sat Dec 13 11:43:27 2014 +0530

    drm/i915/chv: Use timeout mode for RC6 on chv

Cc: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S<deepak.s@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Change VLV GEN6_RP_DOWN_TIMEOUT value to decimal

We use decimal for all the other RP magic values, so change
GEN6_RP_DOWN_TIMEOUT to decimal as well. Also change the order
of the register writes to match the BIOS spec for easier verification.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Deepak S<deepak.s@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Disable RC6 before configuring in on VLV/CHV

Follow the sequence in the BIOS spec and clear the RC_CONTROL register
before changing any of the other RC6/RP registers.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Deepak S<deepak.s@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: New offset for reading frequencies on CHV.

Use new Sideband offset to read max/min/gaur freq based on the SKU it
is running on. Based on the Number of EU, we read different bits to
identify the max frequencies at which system can run.

v2: reuse mask definitions & INTEL_INFO() to get device info (Ville)

v3: add break in switch conditions (Ville)

Signed-off-by: Deepak S <deepak.s@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala at linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>