Sinthu Raja [Wed, 9 Feb 2022 09:36:53 +0000 (15:06 +0530)]
arm: j721e: Add support for selecting DT based on board name
Enable support for selecting DTB from FIT within SPL based on the
board name read from EEPROM. This will help to use single defconfig
for both EVM and SK.
Signed-off-by: Sinthu Raja <sinthu.raja@ti.com>
Sinthu Raja [Wed, 9 Feb 2022 09:36:52 +0000 (15:06 +0530)]
board: ti: j721e: Add support for detecting multiple device trees
Update the board_fit_config_name_match() to choose the right dtb
based on the board name read from EEPROM.
Also restrict multpile EEPROM reads by verifying if EEPROM is already
read.
Signed-off-by: Sinthu Raja <sinthu.raja@ti.com>
Sinthu Raja [Wed, 9 Feb 2022 09:36:51 +0000 (15:06 +0530)]
board: ti: j721e: Disable probing of daughtercards
j721e-sk doesn't have any daughter cards, so disable daughter
card probing inside board_late_init() and spl_board_init() for
j721e-sk.
Signed-off-by: Sinthu Raja <sinthu.raja@ti.com>
Sinthu Raja [Wed, 9 Feb 2022 09:36:50 +0000 (15:06 +0530)]
board: ti: j721e: Add support to update board_name for j721e-sk
Update setup_board_eeprom_env() to choose the right board name
for j721e-sk.
Signed-off-by: Sinthu Raja <sinthu.raja@ti.com>
Sinthu Raja [Wed, 9 Feb 2022 09:36:49 +0000 (15:06 +0530)]
board: ti: j721e: Enable support for reading EEPROM at next alternate address
J721E EVM has EEPROM populated at 0x50. J721E SK has EEPROM populated
at next address 0x51 in order to be compatible with RPi. So start
looking for TI specific EEPROM at 0x50, if not found look for EEPROM at
0x51.
Signed-off-by: Sinthu Raja <sinthu.raja@ti.com>
Sinthu Raja [Wed, 9 Feb 2022 09:36:48 +0000 (15:06 +0530)]
board: ti: j721e: Guard functions with right #ifdef to avoid build warnings
board_late_init(), setup_board_eeprom_env() and setup_serial() is
called only under CONFIG_BOARD_LATE_INIT, so guard these functions
with the same. Also, reorder these functions to place it under
single #ifdef
Signed-off-by: Sinthu Raja <sinthu.raja@ti.com>
Sinthu Raja [Wed, 9 Feb 2022 09:36:47 +0000 (15:06 +0530)]
drivers: power: regulator: tps65941_regulator: Add support for 3Phase buck
Buck regulator 1, 2 and 3 of TPS6594132 on j721e-sk is in 3 Phase
confguration, in-order to support this, add configuring 3 Phase buck
in tps65941 while driver probing.
Signed-off-by: Sinthu Raja <sinthu.raja@ti.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Sinthu Raja [Wed, 9 Feb 2022 09:36:46 +0000 (15:06 +0530)]
drivers: power: pmic: Add support for tps659412 PMIC
Since TPS659412 and TPS659413 are both software compatible,
add a compatible string for the same inside tps65941.c.
Signed-off-by: Sinthu Raja <sinthu.raja@ti.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Tom Rini [Wed, 16 Feb 2022 19:18:44 +0000 (14:18 -0500)]
fdtdec.h: Remove gurads around fdtdec_resetup function
This function has not been conditionally compiled for some time, so
remove the incorrect guards around the declaration.
Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Mon, 14 Feb 2022 22:21:29 +0000 (22:21 +0000)]
configs: Resync with savedefconfig
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Mon, 14 Feb 2022 22:03:08 +0000 (17:03 -0500)]
Prepare v2022.04-rc2
Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Mon, 14 Feb 2022 19:18:45 +0000 (14:18 -0500)]
Merge branch '2022-02-14-assorted-fixes'
- Fix for pstore already being in the DT, "setlocalversion" script
bugfix and pdu001 platform bugfix
Felix Brack [Tue, 8 Feb 2022 10:38:39 +0000 (11:38 +0100)]
arm: pdu001: Fix dt to work with the current am33xx dtsi files
The changes introduced with commit
6337d53fdf45 ("arm: dts: sync am33xx
with Linux 5.9-rc7") prevent the PDU001 from operating correctly.
This patch fixes the configuration of the pin multiplexer and uart3.
Signed-off-by: Felix Brack <fb@ltec.ch>
Nikita Maslov [Thu, 13 Jan 2022 21:13:39 +0000 (00:13 +0300)]
scripts: setlocalversion: remove quotes around localversion from config
After replacing of include/config/auto.conf sourcing with
extraction of CONFIG_LOCALVERSION, resulting version string
contains quotes around localversion part which are always
present in auto.conf (even if localversion is empty).
This patch fixes this script to remove quotes.
Signed-off-by: Nikita Maslov <wkernelteam@gmail.com>
Cc: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Detlev Casanova [Mon, 7 Feb 2022 16:02:30 +0000 (11:02 -0500)]
pstore: Support already existing reserved-memory node
The pstore command tries to create a reserved-memory node but fails if
it is already present with:
Add 'reserved-memory' node failed: FDT_ERR_EXISTS
This patch creates the node only if it does not exist and adapts the reg
values sizes depending on already present #address-cells and #size-cells
values.
Signed-off-by: Detlev Casanova <detlev.casanova@collabora.com>
Tom Rini [Fri, 11 Feb 2022 20:07:49 +0000 (15:07 -0500)]
Merge tag 'efi-2022-04-rc2-4' of https://source.denx.de/u-boot/custodians/u-boot-efi
Pull request for efi-2022-04-rc2-4
Documentation:
* mkeficapsule man-page
UEFI changes:
* add support for signing images to mkeficapsule
* add support for user define capsule GUID
* adjust unit tests for capsules
* fix UEFI image signature validation in case of multiple signatures
Ilias Apalodimas [Fri, 11 Feb 2022 07:37:50 +0000 (09:37 +0200)]
test/py: efi_secboot: adjust secure boot tests to code changes
The previous patch is changing U-Boot's behavior wrt certificate based
binary authentication. Specifically an image who's digest of a
certificate is found in dbx is now rejected. Fix the test accordingly
and add another one testing signatures in reverse order
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Ilias Apalodimas [Fri, 11 Feb 2022 07:37:49 +0000 (09:37 +0200)]
efi_loader: fix dual signed image certification
The EFI spec allows for images to carry multiple signatures. Currently
we don't adhere to the verification process for such images.
The spec says:
"Multiple signatures are allowed to exist in the binary's certificate
table (as per PE/COFF Section "Attribute Certificate Table"). Only one
hash or signature is required to be present in db in order to pass
validation, so long as neither the SHA-256 hash of the binary nor any
present signature is reflected in dbx."
With our current implementation signing the image with two certificates
and inserting both of them in db and one of them dbx doesn't always reject
the image. The rejection depends on the order that the image was signed
and the order the certificates are read (and checked) in db.
While at it move the sha256 hash verification outside the signature
checking loop, since it only needs to run once per image and get simplify
the logic for authenticating an unsigned imahe using sha256 hashes.
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
AKASHI Takahiro [Wed, 9 Feb 2022 10:10:42 +0000 (19:10 +0900)]
test/py: efi_capsule: check the results in case of CAPSULE_AUTHENTICATE
Before the capsule authentication is supported, this test script works
correctly, but with the feature enabled, most tests will fail due to
unsigned capsules.
So check the results depending on CAPSULE_AUTHENTICATE or not.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
AKASHI Takahiro [Wed, 9 Feb 2022 10:10:41 +0000 (19:10 +0900)]
test/py: efi_capsule: add a test for "--guid" option
This test scenario tests a new feature of mkeficapsule, "--guid" option,
which allows us to specify FMP driver's guid explicitly at the command
line.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
AKASHI Takahiro [Wed, 9 Feb 2022 10:10:40 +0000 (19:10 +0900)]
test/py: efi_capsule: align with the syntax change of mkeficapsule
Since the syntax of mkeficapsule was changed in the previous commit,
we need to modify command line arguments in a pytest script.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
AKASHI Takahiro [Wed, 9 Feb 2022 10:10:39 +0000 (19:10 +0900)]
tools: mkeficapsule: allow for specifying GUID explicitly
The existing options, "--fit" and "--raw," are only used to put a proper
GUID in a capsule header, where GUID identifies a particular FMP (Firmware
Management Protocol) driver which then would handle the firmware binary in
a capsule. In fact, mkeficapsule does the exact same job in creating
a capsule file whatever the firmware binary type is.
To prepare for the future extension, the command syntax will be a bit
modified to allow users to specify arbitrary GUID for their own FMP driver.
OLD:
[--fit <image> | --raw <image>] <capsule file>
NEW:
[--fit | --raw | --guid <guid-string>] <image> <capsule file>
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
AKASHI Takahiro [Wed, 9 Feb 2022 10:10:38 +0000 (19:10 +0900)]
test/py: efi_capsule: add image authentication test
Add a couple of test cases against capsule image authentication
for capsule-on-disk, where only a signed capsule file with the verified
signature will be applied to the system.
Due to the difficulty of embedding a public key (esl file) in U-Boot
binary during pytest setup time, all the keys/certificates are pre-created.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
AKASHI Takahiro [Wed, 9 Feb 2022 10:10:37 +0000 (19:10 +0900)]
doc: update UEFI document for usage of mkeficapsule
Now we can use mkeficapsule command instead of EDK-II's script
to create a signed capsule file. So update the instruction for
capsule authentication.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
AKASHI Takahiro [Wed, 9 Feb 2022 10:10:36 +0000 (19:10 +0900)]
tools: mkeficapsule: add man page
Add a man page for mkeficapsule command.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
AKASHI Takahiro [Wed, 9 Feb 2022 10:10:35 +0000 (19:10 +0900)]
tools: mkeficapsule: add firmware image signing
With this enhancement, mkeficapsule will be able to sign a capsule
file when it is created. A signature added will be used later
in the verification at FMP's SetImage() call.
To do that, we need specify additional command parameters:
-monotonic-cout <count> : monotonic count
-private-key <private key file> : private key file
-certificate <certificate file> : certificate file
Only when all of those parameters are given, a signature will be added
to a capsule file.
Users are expected to maintain and increment the monotonic count at
every time of the update for each firmware image.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
AKASHI Takahiro [Wed, 9 Feb 2022 10:10:34 +0000 (19:10 +0900)]
tools: build mkeficapsule with tools-only_defconfig
Add CONFIG_TOOLS_MKEFICAPSULE. Then we want to always build mkeficapsule
if tools-only_defconfig is used.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
AKASHI Takahiro [Wed, 9 Feb 2022 08:24:23 +0000 (17:24 +0900)]
CI: enforce packages upgrade for Msys2 on Windows
We need to install libgnutls-devel package to build the host tool,
mkeficapsule, and as of now, there seems to be a depencency conflict
in the current msys2 installer;
:: installing libp11-kit (0.24.1-1) breaks dependency \
'libp11-kit=0.23.22' required by p11-kit
To resolve this conflict, however, the initial "pacman -Syyuu" in
'tools_only_windows' job is not enough. Another "pacman -Su" will
enforce all the out-of-date packages being upgraded.
(Probably the first "-Syyuu" can be changed to "-Syu".)
See the installation steps in
https://www.msys2.org/
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Tom Rini [Fri, 11 Feb 2022 17:02:31 +0000 (12:02 -0500)]
Merge branch '2022-02-11-assorted-updates-and-fixes'
A partial list:
- fw_env updates, a new testcase for mkimage -o ..., nop-phy reset-gpios
support, DFU updates, kaslr-seed support in extlinux.conf, modern
"partitions" support in mtd device tree
Heinrich Schuchardt [Sat, 29 Jan 2022 15:33:16 +0000 (16:33 +0100)]
test: test field truncation in snprint()
The output size for snprint() should not only be respected for whole fields
but also with fields. Add more tests.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Adam Ford [Sat, 29 Jan 2022 13:27:47 +0000 (07:27 -0600)]
phy: nop-phy: Enable reset-gpios support
Some usb-nop-xceiv devices use a gpio take them out
of reset. Add a reset function to put them into that
state. This is similar to how Linux handles the
usb-nop-xceiv driver.
Signed-off-by: Adam Ford <aford173@gmail.com>
Rafał Miłecki [Wed, 12 Jan 2022 11:47:06 +0000 (12:47 +0100)]
fw_env: simplify logic & code paths in the fw_env_open()
Environment variables can be stored in two formats:
1. Single entry with header containing CRC32
2. Two entries with extra flags field in each entry header
For that reason fw_env_open() has two main code paths and there are
pointers for CRC32/flags/data.
Previous implementation was a bit hard to follow:
1. It was checking for used format twice (in reversed order each time)
2. It was setting "environment" global struct fields to some temporary
values that required extra comments explaining it
This change simplifies that code:
1. It introduces two clear code paths
2. It sets "environment" global struct fields values only once it really
knows them
To be fair there are *two* crc32() calls now and an extra pointer
variable but that should be cheap enough and worth it.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Rafał Miłecki [Wed, 12 Jan 2022 11:47:05 +0000 (12:47 +0100)]
fw_env: make flash_io() take buffer as an argument
It's usually easier to understand code & follow it if all arguments are
passed explicitly. Many coding styles also discourage using global
variables.
Behaviour of flash_io() was a bit unintuitive as it was writing to a
buffer referenced in a global struct. That required developers to
remember how it works and sometimes required hacking "environment"
global struct variable to read data into a proper buffer.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Simon Glass [Sat, 29 Jan 2022 21:30:52 +0000 (14:30 -0700)]
acpi: Move acpi_write_tables() to a generic header
This function is used by both x86 and sandbox. Put it in a common header
file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Masami Hiramatsu [Mon, 31 Jan 2022 02:52:54 +0000 (11:52 +0900)]
cmd/dfu: Enable 'dfu list' command without DFU_OVER_USB
Since dfu is not only used for USB, and some platform only
supports DFU_OVER_TFTP or EFI capsule update, dfu_alt_info
is defined on such platforms too.
For such platform, 'dfu list' command is useful to check
how the current dfu_alt_info setting is parsed.
Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Masami Hiramatsu [Mon, 31 Jan 2022 02:52:46 +0000 (11:52 +0900)]
doc: usage: DFU: Fix dfu_alt_info document
Fix some typo and wrong information about dfu_alt_info.
- Add the parameter format, decimal only or hexadecimal.
- Use same parameter name for the same kind of parameters.
(e.g. dev -> dev_id)
Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Masami Hiramatsu [Mon, 31 Jan 2022 02:52:37 +0000 (11:52 +0900)]
DFU: Check the number of arguments and argument string strictly
When parsing the dfu_alt_info, check the number of arguments
and argument string strictly. If there is any garbage data
(which is not able to be parsed correctly) in dfu_alt_info,
that means something wrong and user may make a typo or mis-
understanding about the syntax. Since the dfu_alt_info is
used for updating the firmware, this mistake may lead to
brick the hardware.
Thus it should be checked strictly for making sure there
is no mistake.
Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Masami Hiramatsu [Mon, 31 Jan 2022 02:52:29 +0000 (11:52 +0900)]
DFU: Accept redundant spaces and tabs in dfu_alt_info
If dfu_alt_info has repeated spaces or tab (for indentation or
readability), the dfu fails to parse it. For example, if
dfu_alt_info="mtd nor1=image raw 100000 200000" (double spaces
after "raw"), the image entity start address is '0' and the size
'0x100000'. This is because the repeated space is not skipped.
Use space and tab as a separater and apply skip_spaces() to
skip redundant spaces and tabs.
Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Masami Hiramatsu [Mon, 31 Jan 2022 02:52:20 +0000 (11:52 +0900)]
DFU: Do not copy the entity name over the buffer size
Use strlcpy() instead of strcpy() to prevent copying the
entity name over the name buffer size.
Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Jan Kiszka [Sat, 5 Feb 2022 12:19:36 +0000 (13:19 +0100)]
mkimage: Improve documentation of algo-name parameter
Addresses the feedback provided on
5902a397d029 ("mkimage: Allow to
specify the signature algorithm on the command line") which raced with
the merge.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
qthedev [Sat, 5 Feb 2022 10:25:16 +0000 (10:25 +0000)]
Replace echo -n's used in environment processing with touch
echo -n does not give the intended effect when invoked in macOS through
/bin/sh, which is the shell make uses by default, see
"https://stackoverflow.com/questions/
11675070/makefile-echo-n-not-working"
for a detailed explanation. In this case, it resulted in "-n" being
written to env.txt and env.in even though they should be empty, which
caused compilation to fail with "Your board uses a text-file
environment, so must not define CONFIG_EXTRA_ENV_SETTINGS".
This patch prevents the error by replacing echo -n's with touch, as they
are used to create empty files in these cases.
Heinrich Schuchardt [Fri, 4 Feb 2022 09:50:04 +0000 (10:50 +0100)]
cmd: wrong printf() code in do_test_stackprot_fail()
strlen() returns size_t. So we should use %zu to print it.
This avoids incorrect output on 32bit systems.
Fixes:
2fc62f299174 ("stackprot: Make our test a bit more complex")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Jan Kiszka [Thu, 3 Feb 2022 20:43:50 +0000 (21:43 +0100)]
test/py: Add test case for mkimage -o argument
Stress the '-o algo_name' argument of mkimage by expanding the vboot
test.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: Update scripts/pylint.base]
Pali Rohár [Thu, 3 Feb 2022 18:51:37 +0000 (19:51 +0100)]
malloc_simple: Remove usage of unsupported %zx format string
Replace %zx by %lx and cast size_t to ulong.
U-Boot currently prints garbage debug output:
size=x, ptr=18, limit=18:
4002a000
With this change it prints correct debug data:
size=18, ptr=18, limit=2000:
4002a000
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Matthias Schiffer [Thu, 3 Feb 2022 14:14:47 +0000 (15:14 +0100)]
common: fdt_support: add support for "partitions" subnode to fdt_fixup_mtdparts()
Listing MTD partitions directly in the flash mode has been deprecated
for a while for kernel Device Trees. Look for a node "partitions" in the
found flash nodes and use it instead of the flash node itself for the
partition list when it exists, so Device Trees following the current
best practices can be fixed up.
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Peter Cai [Wed, 2 Feb 2022 18:04:04 +0000 (13:04 -0500)]
button: adc: set state to pressed when the voltage is closest to nominal
In the Linux implementation of adc-keys
(drivers/input/keyboard/adc-keys.c), `press-threshold-microvolt` is not
really interpreted as a threshold, but rather as the "nominal voltage"
of the button. When the voltage read from the ADC is closest to a
button's `press-threshold-microvolt`, the button is considered pressed.
This patch reconciles the behavior of button-adc with Linux's adc-keys
such that device trees can be synchronized with minimal modifications.
Signed-off-by: Peter Cai <peter@typeblog.net>
Zhang Ning [Tue, 1 Feb 2022 00:33:37 +0000 (08:33 +0800)]
cmd: pxe_utils: sysboot: add kaslr-seed generation support
this will add kaslrseed keyword to sysboot lable,
when it set, it will request to genarate random number
from hwrng as kaslr-seed.
with this patch exlinux.conf label looks like
label l0
menu testing
linux /boot/vmlinuz-5.15.16-arm
initrd /boot/initramfs-5.15.16-arm.img
fdtdir /boot/dtbs/5.15.16-arm/
kaslrseed
append root=UUID=
92ae1e50-eeeb-4c5b-8939-
7e1cd6cfb059 ro
Tested on Khadas VIM with kernel 5.16.0-rc5-arm64, Debian 11.
Signed-off-by: Zhang Ning <zhangn1985@qq.com>
Tom Rini [Fri, 11 Feb 2022 12:22:30 +0000 (07:22 -0500)]
Merge https://source.denx.de/u-boot/custodians/u-boot-usb
Marek Vasut [Fri, 28 Jan 2022 03:39:09 +0000 (04:39 +0100)]
usb: gadget: ci: Avoid null pointer dereference
The ci_req->hw_buf can be NULL, test whether it is and if so,
avoid accessing it. Else, the system may crash.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Peter Chen <peter.chen@nxp.com>
Cc: Li Jun <jun.li@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Thomas Watson [Thu, 10 Feb 2022 21:13:14 +0000 (15:13 -0600)]
console: usb: kbd: Limit poll frequency to improve performance
Using the XHCI driver, the function `usb_kbd_poll_for_event` takes
30-40ms to run. The exact time is dependent on the polling interval the
keyboard requests in its descriptor, and likely cannot be significantly
reduced without major rework to the XHCI driver.
The U-Boot EFI console service sets a timer to poll the keyboard every 5
microseconds, and this timer is checked every time a block is read off
disk. The net effect is that, on my system, loading a ~40MiB kernel and
initrd takes about 62 seconds with a slower keyboard and 53 seconds
with a faster one, with the vast majority of the time spent polling the
keyboard.
To solve this problem, this patch adds a 20ms delay between consecutive
calls to `usb_kbd_poll_for_event`. This is sufficient to reduce the
total loading time to under half a second for both keyboards, and does
not impact the perceived keystroke latency.
Signed-off-by: Thomas Watson <twatson52@icloud.com>
Adam Ford [Thu, 3 Feb 2022 21:20:11 +0000 (15:20 -0600)]
usb: ehci-mx6: Enable OTG detection on imx8mm and imx8mn
The imx8mm and imx8mn appear compatible with imx7d-usb
flags in the OTG driver. If the dr_mode is defined as
host or peripheral, the device appears to operate correctly,
however the auto host/peripheral detection results in an error.
The solution isn't just adding checks for imx8mm and imx8mn to
the check for imx7, because the USB clock needs to be running
to read from the USBNC_PHY_STATUS_OFFSET register or it will hang.
Marek requested that I not enable the clocks in ehci_usb_of_to_plat,
so I modified that function to return an unknown state if the
device tree does not explicitly state whether it is a host
or a peripheral.
When the driver probes, it looks to see if it's in the unknown
state, and only then will it read the register to auto-detect.
Signed-off-by: Adam Ford <aford173@gmail.com>
Tested-by: Tim Harvey <tharvey@gateworks.com>
Tom Rini [Thu, 10 Feb 2022 22:38:04 +0000 (17:38 -0500)]
Merge branch '2022-02-10-platform-updates'
- Assorted Apple M1 platform updates
- Drop CONFIG_SYS_RESET_ADDR, update k3-am64-sk memory values in dts
Sinthu Raja [Mon, 29 Nov 2021 12:04:49 +0000 (17:34 +0530)]
arm:dts:k3-am64-sk: EMIF tool update to 0.8.0 with 1333MTs for lpddr4
EMIF tool for AM64 SK is now updated to 0.8.0 that includes
* disabled Write DQ training
* improve CA ODT to 60 ohms
The lpddr4 enabled with periodic WDQ training is causing periodic 26us
stall. This makes the SoC stall without doing anything which leads to
R5 interrupt latency in TCM memory. Due to this periodic training there
are some outstanding CPU transactions waiting for the lpddr4 to complete.
Hence, disable the periodic write DQ training during the
non-initialization stage of lpddr4 which results in an approximate 1us
stall. Also, update the lpddr4 config to improve CA ODT by 60 ohms
The rationales are as follows:
- PI_WDQLVL_EN: 2 Bits register field to support write DQ leveling,
disable bit 1 that supports Write DQ during non-initialization to
avoid ~26us stall during code execution.
- MR11_DATA_F1/F2_x register fields value changed to 0x66 that changes
the CA ODT from 48ohm to 60ohm to improve the eye margin on CA bus by
increasing the signal swing.
Signed-off-by: James Doublesin <doublesin@ti.com>
Signed-off-by: Sinthu Raja <sinthu.raja@ti.com>
Mark Kettenis [Sun, 6 Feb 2022 12:21:14 +0000 (13:21 +0100)]
apple: Fix debug uart clock rate
The clock rate for the serial console on Apple M1 systems is 24 MHz
instead of 240 kHz.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Ovidiu Panait [Mon, 31 Jan 2022 07:20:22 +0000 (09:20 +0200)]
common: drop CONFIG_SYS_RESET_ADDR
There are no boards that define CONFIG_SYS_RESET_ADDR, so drop the
remaining comments referencing it and also the config_whitelist.txt entry.
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Acked-by: thomas@wytron.com.tw
Ovidiu Panait [Mon, 31 Jan 2022 07:20:21 +0000 (09:20 +0200)]
powerpc: mpc8xx: drop CONFIG_SYS_RESET_ADDRESS
There are no boards that define CONFIG_SYS_RESET_ADDRESS, so drop the
associated mpc8xx code that checks for it.
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Acked-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Mark Kettenis [Sun, 23 Jan 2022 15:48:13 +0000 (16:48 +0100)]
input: apple: Add support for Apple SPI keyboard
This driver adds support for the keyboard on Apple Silicon laptops.
The controller for this keyboard sits on an SPI bus and uses an
Apple-specific HID over SPI protocol. The packets sent by this
controller for key presses and key releases are fairly simple and
are decoded directly by the code in this driver and converted into
standard Linux keycodes. The same controller handles the touchpad
found on these laptops. Packets for touchpad events are simply
ignored.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested on: Macbook Air M1
Tested-by: Simon Glass <sjg@chromium.org>
Mark Kettenis [Sun, 23 Jan 2022 15:48:12 +0000 (16:48 +0100)]
spi: apple: Add driver for Apple SPI controller
Add a driver for the SPI controller integrated on Apple SoCs.
This is necessary to support the keyboard on Apple Silicon laopts
since their keyboard uses an Apple-specific HID over SPI protocol.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested on: Macbook Air M1
Tested-by: Simon Glass <sjg@chromium.org>
Mark Kettenis [Sat, 22 Jan 2022 19:38:19 +0000 (20:38 +0100)]
configs: apple: Add NVMe boot target
Add a boot target for NVMe such that we can boot from NVMe.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Mark Kettenis [Sat, 22 Jan 2022 19:38:18 +0000 (20:38 +0100)]
nvme: apple: Add driver for Apple NVMe storage controller
Add a driver for the NVMe storage controller integrated on
Apple SoCs. This NVMe controller isn't PCI based and deviates
from the NVMe standard in its implementation of the command
submission queue and the integration of an NVMMU that needs
to be managed. This commit tweaks the core NVMe code to
support the linear command submission queue implemented by
this controller. But setting up the submission queue and
managing the NVMMU controller is handled by implementing
the driver ops that were added in an earlier commit.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Tested-on: firefly-rk3399
Tested-by: Mark Kettenis <kettenis@openbsd.org>
Tested on: Macbook Air M1
Tested-by: Simon Glass <sjg@chromium.org>
Mark Kettenis [Sat, 22 Jan 2022 19:38:17 +0000 (20:38 +0100)]
power: domain: apple: Add reset support
The power management controller found on Apple SoCs als provides
a way to reset all devices within a power domain. This is needed
to cleanly shutdown the NVMe controller before we hand over
control to the OS.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested on: Macbook Air M1
Tested-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Mark Kettenis [Sat, 22 Jan 2022 19:38:16 +0000 (20:38 +0100)]
nvme: Add shutdown function
Add a function to disable the NVMe controller. This will be used
to let the driver for the NVMe storage integrated on Apple SoCs
shutdown the NVMe controller such we can shutdown the NVMe
IOP controller in a clean way afterwards before handing control
to the OS.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested on: Macbook Air M1
Tested-by: Simon Glass <sjg@chromium.org>
Mark Kettenis [Sat, 22 Jan 2022 19:38:15 +0000 (20:38 +0100)]
nvme: Introduce driver ops
The NVMe storage controller integrated on Apple SoCs deviates
from the NVMe standard in two aspects. It uses a "linear"
submission queue and it integrates an NVMMU that needs to be
programmed for each NVMe command. Introduce driver ops such
that we can set up the linear submission queue and program the
NVMMU in the driver for this strange beast.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested on: Macbook Air M1
Tested-by: Simon Glass <sjg@chromium.org>
Mark Kettenis [Sat, 22 Jan 2022 19:38:14 +0000 (20:38 +0100)]
arm: apple: Add RTKit support
Most Apple IOPs run a firmware that is based on what Apple calls
RTKit. RTKit implements a common mailbox protocol. This code
provides an implementation of the AP side of this protocol,
providing a function to initialize RTKit-based firmwares as well
as a function to do a clean shutdown of this firmware.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested on: Macbook Air M1
Tested-by: Simon Glass <sjg@chromium.org>
Mark Kettenis [Sat, 22 Jan 2022 19:38:13 +0000 (20:38 +0100)]
arm: apple: Change SoC name from "m1" into "apple"
U-Boot is expected to support multiple generations of Apple SoCs
in a single binary with a single defconfig. Therefore it makes
more sense to set SYS_SOC to "apple".
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Mark Kettenis [Sat, 22 Jan 2022 19:38:12 +0000 (20:38 +0100)]
mailbox: apple: Add driver for Apple IOP mailbox
This mailbox driver provides a communication channel with the
Apple IOP controllers found on Apple SoCs. These IOP controllers
are used to implement various functions such as the System
Manegement Controller (SMC) and NVMe storage. It allows sending
and receiving a 96-bit message over a single channel.
The header file with the struct used for mailbox messages is taken
straight from Linux.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Signed-off-by: Sven Peter <sven@svenpeter.dev>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested on: Macbook Air M1
Tested-by: Simon Glass <sjg@chromium.org>
Mark Kettenis [Sat, 22 Jan 2022 19:38:11 +0000 (20:38 +0100)]
nvme: Split out PCI support
Apple SoCs have an integrated NVMe controller that isn't connected
over a PCIe bus. In preparation for adding support for this NVMe
controller, split out the PCI support into its own file. This file
is selected through a new CONFIG_NVME_PCI Kconfig option, so do
a wholesale replacement of CONFIG_NVME with CONFIG_NVME_PCI.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested on: Macbook Air M1
Tested-by: Simon Glass <sjg@chromium.org>
Tom Rini [Thu, 10 Feb 2022 20:09:55 +0000 (15:09 -0500)]
Merge https://source.denx.de/u-boot/custodians/u-boot-riscv
Tom Rini [Thu, 10 Feb 2022 14:02:06 +0000 (09:02 -0500)]
Merge tag 'dm-pull-8feb22-take3' of https://gitlab.denx.de/u-boot/custodians/u-boot-dm
patman snake-case conversion
binman fit improvements
ACPI fixes and making MCFG available to ARM
[trini: Update scripts/pylint.base]
Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Thu, 10 Feb 2022 12:37:14 +0000 (07:37 -0500)]
Merge https://gitlab.denx.de/u-boot/custodians/u-boot-marvell
- kwboot: Misc improvements and fixes (Pali)
- Kirkwood: Move to DM ethernet support for some boards (Tony)
- Minor misc stuff
Tony Dinh [Wed, 9 Feb 2022 02:56:22 +0000 (18:56 -0800)]
arm: kirkwood: Pogoplug E02 : Convert Ethernet to Driver Model
The Pogoplug E02 board has the network chip Marvell 88E1116R. Convert
to Driver Model and use uclass mvgbe and the compatible driver M88E1118R
to bring up Ethernet.
- Add board_eth_init(), CONFIG_DM_ETH, and CONFIG_PHY_MARVELL
to bring up Ethernet.
- Currently, CONFIG_RESET_PHY_R symbol is used in
arch/arm/mach-kirkwood/include/mach/config.h for all Kirkwood
boards with mv8831116 PHY, with each board defines the function
reset_phy(). Undefine it for this board.
- As the result of the migration to Driver Model, this u-boot image has
grown substantially (about 100K, give or take). The old envs location
at 0x60000 (384k) is no longer possible. Move it to 0xC0000 (768K).
- Miscellaneous changes: Move constants to .c file and remove header file
board/cloudengines/pogo_e02/pogo_e02.h, use CONFIG_SYS_THUMB_BUILD to
keep u-boot image under 512K, use BIT macro, and cleanup comments.
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Pali Rohár [Mon, 7 Feb 2022 09:12:24 +0000 (10:12 +0100)]
tools: kwboot: Allow to use -b without image path as the last getopt() option
Currently it is possible to call "kwboot -b -t /dev/ttyUSB0" but not to
call "kwboot -b /dev/ttyUSB0".
Fix it by not trying to process the last argv[], which is non-getopt()
option (tty path) as the image path for -b.
Fixes:
c513fe47dca2 ("tools: kwboot: Allow to use option -b without image path")
Reported-by: Marcel Ziswiler <marcel@ziswiler.com>
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marcel Ziswiler <marcel@ziswiler.com>
Tested-by: Marcel Ziswiler <marcel@ziswiler.com>
Tony Dinh [Thu, 3 Feb 2022 22:32:29 +0000 (14:32 -0800)]
arm: kirkwood: Dockstar : Add DM Ethernet
The Dockstar board has the network chip Marvell 88E1116R. Convert to
Ethernet driver model, and use uclass mvgbe and the compatible driver
M88E1118R to bring up Ethernet.
- Add CONFIG_DM_ETH and associated configs.
- Add board_eth_init() to use uclass mvgbe to bring up the network.
And remove ad-hoc code.
- Add CONFIG_PHY_MARVELL to properly configure the network.
- Currently, CONFIG_RESET_PHY_R symbol is used in
arch/arm/mach-kirkwood/include/mach/config.h for all Kirkwood
boards with mv8831116 PHY, with each board defines the function
reset_phy(). Undefine it for this board.
- Miscellaneous changes: Move constants to .c file and remove
header file board/Seagate/dockstar/dockstar.h, use
CONFIG_SYS_THUMB_BUILD to keep u-boot image
under 512K, add CONFIG_HUSH_PARSER, use BIT macro, and cleanup comments.
- Note: This patch is a RESEND for a previous patch:
https://patchwork.ozlabs.org/project/uboot/patch/
20210812051854.1340-2-mibodhi@gmail.com/
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Pali Rohár [Thu, 3 Feb 2022 16:57:49 +0000 (17:57 +0100)]
MAINTAINERS: Update list of Armada 385 and Armada 3720 drivers
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Pali Rohár [Thu, 3 Feb 2022 16:45:20 +0000 (17:45 +0100)]
tools: kwboot: Fix detection of quit esc sequence
Quit esc sequence may be also in the middle of the read buffer.
Fix the detection for that case.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Tony Dinh [Wed, 2 Feb 2022 05:59:27 +0000 (21:59 -0800)]
arm: kirkwood: iConnect : Add Ethernet support
- Currently, CONFIG_RESET_PHY_R symbol is used in
arch/arm/mach-kirkwood/include/mach/config.h for all Kirkwood
boards with mv8831116 PHY, with each board defines the function
reset_phy(). Undefine it for this board.
- Add board_eth_init(), CONFIG_DM_ETH, and CONFIG_PHY_MARVELL
to bring up Ethernet.
- Miscellaneous changes: Move constants to .c file and remove header file
board/iomega/iconnect/iconnect.h. Add CONFIG_HUSH_PARSER, use BIT macro,
and cleanup comments.
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Tony Dinh [Sun, 30 Jan 2022 23:02:30 +0000 (15:02 -0800)]
arm: kirkwood: Dreamplug : Use Marvell uclass mvgbe and PHY driver for Ethernet
The Globalscale Technologies Dreamplug board has the network chip
Marvell 88E1116R. Use uclass mvgbe and the compatible driver M88E1310
driver to bring up Ethernet.
- Currently, CONFIG_RESET_PHY_R symbol is used in
arch/arm/mach-kirkwood/include/mach/config.h for all Kirkwood
boards with mv8831116 PHY, with each board defines the function
reset_phy(). Undefine it for this board.
- Add board_eth_init() to use uclass mvgbe to bring up both network
port 0 and 1. And remove ad-hoc code.
- Enable CONFIG_PHY_MARVELL to properly configure the network.
- Add myself as maintainer (this board seems to be orphaned,
could not contact Jason Cooper using current email).
- Miscellaneous changes: Move constants to .c file and remove header file
board/Marvell/dreamplug/dreamplug.h, cleanup comments.
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Pali Rohár <pali@kernel.org>
Anup Patel [Thu, 27 Jan 2022 06:11:10 +0000 (11:41 +0530)]
doc: qemu-riscv: Update documentation for QEMU spike machine
We can now use same U-Boot images on both QEMU virt machine and QEMU
spike machine so let's update the QEMU RISC-V documentation.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Anup Patel [Thu, 27 Jan 2022 06:11:09 +0000 (11:41 +0530)]
riscv: qemu: Implement is_flash_available() for MTD NOR
Currently, if MTD NOR is enabled then U-Boot tries to issue flash
commands even when CFI flash DT node is not present. This causes
access fault on RISC-V emulators or ISS which do not emulate CFI
flash. To handle this issue, we implement is_flash_available() for
qemu-riscv board which will return 1 only if CFI flash DT node is
present.
Fixes:
d248627f9d42 ("riscv: qemu: Enable MTD NOR flash support")
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Anup Patel [Thu, 27 Jan 2022 06:11:08 +0000 (11:41 +0530)]
riscv: qemu: Enable HTIF console support
Enable support for HTIF console so that we can use QEMU RISC-V U-Boot
on RISC-V emulators and ISS having it.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@vrull.eu>
Reviewed-by: Rick Chen <rick@andestech.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Anup Patel [Thu, 27 Jan 2022 06:11:07 +0000 (11:41 +0530)]
serial: Add RISC-V HTIF console driver
Quite a few RISC-V emulators and ISS (including Spike) have host
transfer interface (HTIF) based console. This patch adds HTIF
based console driver for RISC-V platforms which depends totally
on DT node for HTIF register base address.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@vrull.eu>
Reviewed-by: Rick Chen <rick@andestech.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Alper Nebi Yasak [Mon, 7 Feb 2022 22:08:07 +0000 (01:08 +0300)]
binman: Convert FIT entry type to a subclass of Section entry type
The binman FIT entry type shares some code with the Section entry type.
This shared code is bound to grow, since FIT entries are conceptually a
variation of Section entries.
Make FIT entry type a subclass of Section entry type, simplifying it a
bit and providing us the features that Section implements. Also fix the
subentry alignment test which now attempts to write symbols to a
nonexistent SPL ELF test file by creating it first.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Avoid AddMissingProperties() and SetCalculatedProperties() with FIT:
Signed-off-by: Simon Glass <sjg@chromium.org>
Alper Nebi Yasak [Mon, 7 Feb 2022 22:08:06 +0000 (01:08 +0300)]
binman: Check missing bintools of Section subclasses
Binman can check for missing binary tools and prints warnings if
anything required for an image is missing. The implementation of this
for the Section entry only checks the subentries, presumably because
Section does not use any binary tools itself. However, this means the
check is also skipped for subclasses of Section which might need binary
tools.
Make sure missing binary tools are checked for subclasses of the Section
entry type as well, by calling the parent class' implementation in
the relevant Section method.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Alper Nebi Yasak [Mon, 7 Feb 2022 22:08:05 +0000 (01:08 +0300)]
binman: Register and check bintools from FIT subentries
Binman keeps track of binary tools each entry wants to use. The
implementation of this for the FIT entry only adds "mkimage", but not
the tools that would be used by its subentries.
Register the binary tools that FIT subentries will use in addition to
the one FIT itself uses, and check their existence by copying the
appropriate method from Section entry type. Also add tests that check if
these subentries can use and warn about binary tools.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Alper Nebi Yasak [Mon, 7 Feb 2022 22:08:04 +0000 (01:08 +0300)]
binman: Fix subentry expansion for FIT entry type
Binman tries to expand some entries into parts that make it up, e.g.
'u-boot' into a 'u-boot-expanded' section that contains 'u-boot-nodtb'
and 'u-boot-dtb'. Entries with child entries must call ExpandEntries()
on them to build a correct image, as it's possible that unexpanded child
entries have no data of their own. The FIT entry type doesn't currently
do this, which means putting a "u-boot" entry inside it doesn't work as
expected.
Implement ExpandEntries() for FIT and add a copy of a simple FIT image
test that checks subentry expansion in FIT entries.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Moritz Fischer [Sat, 5 Feb 2022 20:17:45 +0000 (12:17 -0800)]
acpi: Move MCFG implementation to common lib
MCFG tables are used on multiple arches. Move to common ACPI lib.
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Moritz Fischer <moritzf@google.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Use sizeof(*mcfg) instead of sizeof(*header)
Signed-off-by: Simon Glass <sjg@chromium.org>
Moritz Fischer [Sat, 5 Feb 2022 20:17:44 +0000 (12:17 -0800)]
arch: x86: lib: acpi_table: Fix MCFG entries
Commit
d953137526cc ("x86: Move SSDT table to a writer function")
introduced a bug where the actual MCFG entries are no longer generated.
Cc: Simon Glass <sjg@chromium.org>
Fixes:
d953137526cc ("x86: Move SSDT table to a writer function")
Signed-off-by: Moritz Fischer <moritzf@google.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Heiko Schocher [Wed, 2 Feb 2022 12:55:19 +0000 (13:55 +0100)]
serial-uclass: fix build warning
if CONFIG_DM_STDIO is defined but SERIAL_PRESENT not,
gcc drops warnings for serial_stub_* functions
that they are defined but not used.
Fix it.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Heiko Schocher [Wed, 2 Feb 2022 12:53:17 +0000 (13:53 +0100)]
serial: remove nulldev_serial_input
nulldev_serial_input is static and not used in this file,
so remove it.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Simon Glass [Sat, 29 Jan 2022 21:14:19 +0000 (14:14 -0700)]
patman: Update with new pylint scores
Update the new baseline since various scores have improved.
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Sat, 29 Jan 2022 21:14:18 +0000 (14:14 -0700)]
patman: Convert camel case in terminal.py
Convert this file to snake case and update all files which use it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Sat, 29 Jan 2022 21:14:17 +0000 (14:14 -0700)]
patman: Rename Color() method to build()
This method has the same name as its class which is confusing. It is also
annoying when searching the code.
It builds a string with a colour, so rename it to build().
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Sat, 29 Jan 2022 21:14:16 +0000 (14:14 -0700)]
patman: Rename Print() to Tprint()
Rename this function so that when we convert it to snake case it will not
conflict with the built-in print() function.
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Sat, 29 Jan 2022 21:14:15 +0000 (14:14 -0700)]
patman: Convert camel case in tout.py
Convert this file to snake case and update all files which use it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Sat, 29 Jan 2022 21:14:14 +0000 (14:14 -0700)]
patman: Convert camel case in test_util.py
Convert this file to snake case and update all files which use it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Sat, 29 Jan 2022 21:14:13 +0000 (14:14 -0700)]
patman: Convert camel case in test_checkpatch.py
Convert this file to snake case and update all files which use it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Sat, 29 Jan 2022 21:14:12 +0000 (14:14 -0700)]
patman: Convert camel case in project.py
Convert this file to snake case and update all files which use it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Sat, 29 Jan 2022 21:14:11 +0000 (14:14 -0700)]
patman: Convert camel case in gitutil.py
Convert this file to snake case and update all files which use it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Sat, 29 Jan 2022 21:14:10 +0000 (14:14 -0700)]
patman: Convert camel case in get_maintainer.py
Convert this file to snake case and update all files which use it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Sat, 29 Jan 2022 21:14:09 +0000 (14:14 -0700)]
patman: Convert camel case in func_test.py
Convert this file to snake case and update all files which use it.
Signed-off-by: Simon Glass <sjg@chromium.org>