Masahiro Yamada [Tue, 13 Jun 2017 13:45:37 +0000 (22:45 +0900)]
mtd: nand: denali: handle timing parameters by setup_data_interface()
Handling timing parameters in a driver's own way should be avoided
because it duplicates efforts of drivers/mtd/nand/nand_timings.c
Besides, this driver hard-codes Intel specific parameters such as
CLK_X=5, CLK_MULTI=4. Taking a certain device (Samsung K9WAG08U1A)
into account by get_samsung_nand_para() is weird as well.
Now, the core framework provides .setup_data_interface() hook, which
handles timing parameters in a generic manner.
While I am working on this, I found even more issues in the current
code, so fixed the following as well:
- In recent IP versions, WE_2_RE and TWHR2 share the same register.
Likewise for ADDR_2_DATA and TCWAW, CS_SETUP_CNT and TWB. When
updating one, the other must be masked. Otherwise, the other will
be set to 0, then timing settings will be broken.
- The recent IP release expanded the ADDR_2_DATA to 7-bit wide.
This register is related to tADL. As commit
74a332e78e8f ("mtd:
nand: timings: Fix tADL_min for ONFI 4.0 chips") addressed, the
ONFi 4.0 increased the minimum of tADL to 400 nsec. This may not
fit in the 6-bit ADDR_2_DATA in older versions. Check the IP
revision and handle this correctly, otherwise the register value
would wrap around.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Masahiro Yamada [Tue, 13 Jun 2017 13:45:36 +0000 (22:45 +0900)]
mtd: nand: denali: remove unneeded find_valid_banks()
The function find_valid_banks() issues the Read ID (0x90) command,
then compares the first byte (Manufacturer ID) of each bank with
the one of bank0.
This is equivalent to what nand_scan_ident() does. The number of
chips is detected there, so this is unneeded.
What is worse for find_valid_banks() is that, if multiple chips are
connected to INTEL_CE4100 platform, it crashes the kernel by BUG().
This is what we should avoid. This function is just harmful and
unneeded.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Masahiro Yamada [Tue, 13 Jun 2017 13:45:35 +0000 (22:45 +0900)]
mtd: nand: denali: set NAND_ECC_CUSTOM_PAGE_ACCESS
The denali_cmdfunc() actually does nothing valuable for
NAND_CMD_{PAGEPROG,READ0,SEQIN}.
For NAND_CMD_{READ0,SEQIN}, it copies "page" to "denali->page", then
denali_read_page(_raw) compares them just for the sanity check.
(Inconsistently, this check is missing from denali_write_page(_raw).)
The Denali controller is equipped with high level read/write interface,
so let's skip unneeded call of cmdfunc().
If NAND_ECC_CUSTOM_PAGE_ACCESS is set, nand_write_page() will not
call ->waitfunc hook. So, ->write_page(_raw) hooks should directly
return -EIO on failure. The error handling of page writes will be
much simpler.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Alexandre Belloni [Tue, 13 Jun 2017 12:58:42 +0000 (14:58 +0200)]
mtd: nand: atmel: drop unused include
The Atmel NAND driver doesn't used anything from
linux/platform_data/atmel.h, stop including it.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Masahiro Yamada [Wed, 7 Jun 2017 11:52:14 +0000 (20:52 +0900)]
mtd: nand: denali_dt: add compatible strings for UniPhier SoC variants
Add two compatible strings for UniPhier SoC family.
"socionext,uniphier-denali-nand-v5a" is used on UniPhier sLD3, LD4,
Pro4, sLD8.
"socionext,uniphier-denali-nand-v5b" is used on UniPhier Pro5, PXs2,
LD6b, LD11, LD20.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Masahiro Yamada [Wed, 7 Jun 2017 11:52:13 +0000 (20:52 +0900)]
mtd: nand: denali: remove Toshiba and Hynix specific fixup code
The Denali IP can automatically detect device parameters such as
page size, oob size, device width, etc. and this driver currently
relies on it. However, this hardware function is known to be
problematic.
[1] Due to a hardware bug, various misdetected cases were reported.
That is why get_toshiba_nand_para() and get_hynix_nand_para()
exist to fix-up the misdetected parameters. It is not realistic
to add a new NAND device to the *black list* every time we are
hit by a misdetected case. We would never be able to guarantee
that all cases are covered.
[2] Because this feature is unreliable, it is disabled on some
platforms.
The nand_scan_ident() detects device parameters in a more tested
way. The hardware should not set the device parameter registers in
a different, unreliable way. Instead, set the parameters from the
nand_scan_ident() back to the registers.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Masahiro Yamada [Wed, 7 Jun 2017 11:52:12 +0000 (20:52 +0900)]
mtd: nand: denali: avoid hard-coding ECC step, strength, bytes
This driver was originally written for the Intel MRST platform with
several platform-specific parameters hard-coded.
Currently, the ECC settings are hard-coded as follows:
#define ECC_SECTOR_SIZE 512
#define ECC_8BITS 14
#define ECC_15BITS 26
Therefore, the driver can only support two cases.
- ecc.size = 512, ecc.strength = 8 --> ecc.bytes = 14
- ecc.size = 512, ecc.strength = 15 --> ecc.bytes = 26
However, these are actually customizable parameters, for example,
UniPhier platform supports the following:
- ecc.size = 1024, ecc.strength = 8 --> ecc.bytes = 14
- ecc.size = 1024, ecc.strength = 16 --> ecc.bytes = 28
- ecc.size = 1024, ecc.strength = 24 --> ecc.bytes = 42
So, we need to handle the ECC parameters in a more generic manner.
Fortunately, the Denali User's Guide explains how to calculate the
ecc.bytes. The formula is:
ecc.bytes = 2 * CEIL(13 * ecc.strength / 16) (for ecc.size = 512)
ecc.bytes = 2 * CEIL(14 * ecc.strength / 16) (for ecc.size = 1024)
For DT platforms, it would be reasonable to allow DT to specify ECC
strength by either "nand-ecc-strength" or "nand-ecc-maximize". If
none of them is specified, the driver will try to meet the chip's ECC
requirement.
For PCI platforms, the max ECC strength is used to keep the original
behavior.
Newer versions of this IP need ecc.size and ecc.steps explicitly
set up via the following registers:
CFG_DATA_BLOCK_SIZE (0x6b0)
CFG_LAST_DATA_BLOCK_SIZE (0x6c0)
CFG_NUM_DATA_BLOCKS (0x6d0)
For older IP versions, write accesses to these registers are just
ignored.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Masahiro Yamada [Wed, 7 Jun 2017 11:52:11 +0000 (20:52 +0900)]
mtd: nand: add a shorthand to generate nand_ecc_caps structure
struct nand_ecc_caps was designed as flexible as possible to support
multiple stepsizes (like sunxi_nand.c).
So, we need to write multiple arrays even for the simplest case.
I guess many controllers support a single stepsize, so here is a
shorthand macro for the case.
It allows to describe like ...
NAND_ECC_CAPS_SINGLE(denali_pci_ecc_caps, denali_calc_ecc_bytes, 512, 8, 15);
... instead of
static const int denali_pci_ecc_strengths[] = {8, 15};
static const struct nand_ecc_step_info denali_pci_ecc_stepinfo = {
.stepsize = 512,
.strengths = denali_pci_ecc_strengths,
.nstrengths = ARRAY_SIZE(denali_pci_ecc_strengths),
};
static const struct nand_ecc_caps denali_pci_ecc_caps = {
.stepinfos = &denali_pci_ecc_stepinfo,
.nstepinfos = 1,
.calc_ecc_bytes = denali_calc_ecc_bytes,
};
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Masahiro Yamada [Wed, 7 Jun 2017 11:52:10 +0000 (20:52 +0900)]
mtd: nand: add generic helpers to check, match, maximize ECC settings
Driver are responsible for setting up ECC parameters correctly.
Those include:
- Check if ECC parameters specified (usually by DT) are valid
- Meet the chip's ECC requirement
- Maximize ECC strength if NAND_ECC_MAXIMIZE flag is set
The logic can be generalized by factoring out common code.
This commit adds 3 helpers to the NAND framework:
nand_check_ecc_caps - Check if preset step_size and strength are valid
nand_match_ecc_req - Match the chip's requirement
nand_maximize_ecc - Maximize the ECC strength
To use the helpers above, a driver needs to provide:
- Data array of supported ECC step size and strength
- A hook that calculates ECC bytes from the combination of
step_size and strength.
By using those helpers, code duplication among drivers will be
reduced.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Masahiro Yamada [Mon, 5 Jun 2017 23:21:41 +0000 (08:21 +0900)]
mtd: nand: denali: use BIT() and GENMASK() for register macros
Use BIT() and GENMASK() for register field macros. This will make
it easier to compare the macros with the register description in the
Denali User's Guide.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Masahiro Yamada [Mon, 5 Jun 2017 23:21:40 +0000 (08:21 +0900)]
mtd: nand: denali_dt: clean up resource ioremap
No need to use two struct resource pointers. Just reuse one.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Matthias Lange [Mon, 5 Jun 2017 09:34:38 +0000 (11:34 +0200)]
mtd: nand: gpmi: fix typo in comment
Signed-off-by: Matthias Lange <matthias.lange@kernkonzept.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Matthias Lange [Mon, 5 Jun 2017 09:33:51 +0000 (11:33 +0200)]
mtd: nand: gpmi: Fix typo in data structure name
This makes it easier to grep.
Signed-off-by: Matthias Lange <matthias.lange@kernkonzept.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Arvind Yadav [Thu, 1 Jun 2017 10:58:15 +0000 (16:28 +0530)]
mtd: nand: orion: Handle return value of clk_prepare_enable
clk_prepare_enable() can fail here and we must check its return value.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Boris Brezillon [Sat, 10 Jun 2017 10:09:05 +0000 (12:09 +0200)]
mtd: nand: fsl_ifc: fix handing of bit flips in erased pages
If we see unrecoverable ECC error, we need to count number of bitflips
from all-ones and report correctable/uncorrectable according to
that. Otherwise we report ECC failed on erased flash with single bit error.
Signed-off-by: Pavel Machek <pavel@denx.de>
Reported-by: Darwin Dingel <Darwin.Dingel@alliedtelesis.co.nz>
Acked-by: Darwin Dingel <Darwin.Dingel@alliedtelesis.co.nz>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Xiaolei Li [Wed, 31 May 2017 08:26:41 +0000 (16:26 +0800)]
mtd: nand: mediatek: add support for MT2712 NAND FLASH Controller
MT2712 NAND FLASH Controller is similar to MT2701 except those following:
(1) MT2712 supports up to 148B spare size per 1KB size sector (the same
with 74B spare size per 512B size sector). There are three new spare
format: 61, 67, 74.
(2) MT2712 supports up to 80 bit ecc strength. There are three new ecc
strength level: 68, 72, 80.
(3) MT2712 ECC encode parity data register's start offset is 0x300, and
different with 0x10 of MT2701.
(4) MT2712 improves ecc irq function. When ECC works in ECC_NFI_MODE,
MT2701 will generate ecc irq number the same with ecc steps during
page read. However, MT2712 can only generate one ecc irq.
Changes of this patch are:
(1) add two new variables named pg_irq_sel, encode_parity_reg0 in struct
mtk_ecc_caps.
(2) add new bitfield ECC_PG_IRQ_SEL for register ECC_IRQ_REG.
(3) add ecc strength array of mt2712.
(4) add spare size array of mt2712.
(5) add mt2712 nfc and ecc device compatiable and data.
Signed-off-by: Xiaolei Li <xiaolei.li@mediatek.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Xiaolei Li [Wed, 31 May 2017 08:26:40 +0000 (16:26 +0800)]
mtd: nand: mediatek: add support for different MTK NAND FLASH Controller IP
ECC strength and spare size supported may be different among MTK NAND
FLASH Controller IPs.
This patch contains changes as following:
(1) add new struct mtk_nfc_caps to support different spare size.
(2) add new struct mtk_ecc_caps to support different ecc strength.
(3) remove ECC_CNFG_xBIT define, use a for loop to do ecc strength config.
(4) remove PAGEFMT_SPARE_ define, use a for loop to do spare format config.
(5) malloc ecc->eccdata buffer according to max ecc strength of this IP.
Signed-off-by: Xiaolei Li <xiaolei.li@mediatek.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Xiaolei Li [Wed, 31 May 2017 08:26:39 +0000 (16:26 +0800)]
mtd: nand: mediatek: refine register NFI_PAGEFMT setting
The register NFI_PAGEFMT is always 32 bits length, so it is better to
do register program using writel() compare with writew().
Signed-off-by: Xiaolei Li <xiaolei.li@mediatek.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Xiaolei Li [Wed, 31 May 2017 08:26:38 +0000 (16:26 +0800)]
mtd: nand: mediatek: update DT bindings
Add MT2712 NAND Flash Controller dt bindings documentation.
Signed-off-by: Xiaolei Li <xiaolei.li@mediatek.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Arnd Bergmann [Wed, 31 May 2017 08:19:26 +0000 (10:19 +0200)]
mtd: nand: atmel: mark resume function __maybe_unused
The newly added suspend/resume support causes a harmless warning:
drivers/mtd/nand/atmel/nand-controller.c:2513:12: error: 'atmel_nand_controller_resume' defined but not used [-Werror=unused-function]
This shuts up the warning with a __maybe_unused annotation.
Fixes: b107007a7114 ("mtd: nand: atmel: Add PM ops")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Masahiro Yamada [Thu, 25 May 2017 04:50:20 +0000 (13:50 +0900)]
mtd: nand: check ecc->total sanity in nand_scan_tail
Drivers are supposed to set correct ecc->{size,strength,bytes} before
calling nand_scan_tail(), but it does not complain about ecc->total
bigger than oobsize.
In this case, chip->scan_bbt() crashes due to memory corruption, but
it is hard to debug. It would be kind to fail it earlier with a clear
message.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Boris Brezillon [Tue, 16 May 2017 16:35:45 +0000 (18:35 +0200)]
mtd: nand: Support 'EXIT GET STATUS' command in nand_command[_lp]()
READ0 is sometimes used to exit GET STATUS mode. When this is the case
no address cycles are requested, and we can use this information to
detect that READSTART should not be issued after READ0 or that we
shouldn't wait for the chip to be ready.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Boris Brezillon [Tue, 16 May 2017 16:27:49 +0000 (18:27 +0200)]
mtd: nand: Wait for PAGEPROG to finish in drivers setting NAND_ECC_CUSTOM_PAGE_ACCESS
Drivers setting NAND_ECC_CUSTOM_PAGE_ACCESS are supposed to handle the
full read/write page sequence, and waiting for a page to actually be
programmed is part of this write-page sequence.
This is also what is done in ->write_oob_xxx() hooks, so let's do that in
->write_page_xxx() as well to make it consistent.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Boris Brezillon [Wed, 17 May 2017 08:47:50 +0000 (10:47 +0200)]
mtd: nand: tango: Fix incorrect use of SEQIN command
SEQIN is supposed to be used when one wants to start programming a page.
What we want here is just to change the column within the page, which is
done with the RNDIN command.
Fixes: 6956e2385a16 ("mtd: nand: add tango NAND flash controller support")
Cc: stable@vger.kernel.org
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Boris Brezillon [Mon, 15 May 2017 22:23:46 +0000 (00:23 +0200)]
mtd: nand: sunxi: Remove unneeded ->cmdfunc(NAND_CMD_READ0, 0, page)
The core already sends the NAND_CMD_READ0 for us. Duplicating this call
in the driver is useless and introduces a perf penalty.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Boris Brezillon [Mon, 15 May 2017 22:23:45 +0000 (00:23 +0200)]
mtd: nand: sunxi: Actually use DMA for subpage reads
ecc->read_subpage is set to sunxi_nfc_hw_ecc_read_subpage_dma when
->dmac != NULL, but is then unconditionally overwritten in the common
init path.
Remove this extra assignment to allow usage of the DMA operation when
possible.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Boris Brezillon [Sat, 6 May 2017 16:03:33 +0000 (18:03 +0200)]
mtd: nand: Drop the ->errstat() hook
The ->errstat() hook is no longer implemented NAND controller drivers.
Get rid of it before someone starts abusing it.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Boris Brezillon [Mon, 15 May 2017 22:17:41 +0000 (00:17 +0200)]
mtd: nand: Drop unused cached programming support
Cached programming is always skipped, so drop the associated code until
we decide to really support it.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Boris Brezillon [Thu, 16 Mar 2017 08:36:00 +0000 (09:36 +0100)]
mtd: nand: atmel: Add PM ops
Provide a ->resume() hook to make sure the NAND timings are correctly
restored by resetting all chips connected to the controller.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Boris Brezillon [Thu, 16 Mar 2017 08:35:59 +0000 (09:35 +0100)]
mtd: nand: atmel: Add ->setup_data_interface() hooks
The NAND controller IP can adapt the NAND controller timings dynamically.
Implement the ->setup_data_interface() hook to support this feature.
Note that it's not supported on at91rm9200 because this SoC has a
completely different SMC block, which is not supported yet.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Boris Brezillon [Thu, 16 Mar 2017 08:35:58 +0000 (09:35 +0100)]
mtd: nand: Pass the CS line to ->setup_data_interface()
Some NAND controllers can assign different NAND timings to different
CS lines. Pass the CS line information to ->setup_data_interface() so
that the NAND controller driver knows which CS line is concerned by
the setup_data_interface() request.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Boris Brezillon [Mon, 10 Apr 2017 08:35:18 +0000 (10:35 +0200)]
mtd: nand: gpmi: Kill gpmi_nand_exit()
The only user of gpmi_nand_exit() is gpmi_nand_remove(). Move its content
to the caller.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Han Xu <han.xu@nxp.com>
Boris Brezillon [Mon, 10 Apr 2017 08:35:17 +0000 (10:35 +0200)]
mtd: nand: gpmi: Fix gpmi_nand_init() error path
The GPMI driver is wrongly assuming that nand_release() can safely be
called on an uninitialized/unregistered NAND device.
Add a new err_nand_cleanup label in the error path and only execute if
nand_scan_tail() succeeded.
Note that we now call nand_cleanup() instead of nand_release()
(nand_release() is actually grouping the mtd_device_unregister() and
nand_cleanup() in one call) because there's no point in trying to
unregister a device that has never been registered.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Han Xu <han.xu@nxp.com>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Stefan Agner [Sat, 22 Apr 2017 01:23:36 +0000 (18:23 -0700)]
mtd: gpmi: document current clock requirements
The clock requirements are completely missing, add the clocks
currently required by the driver.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Stefan Agner [Sat, 22 Apr 2017 01:23:35 +0000 (18:23 -0700)]
mtd: nand: gpmi: add i.MX 7 SoC support
Add support for i.MX 7 SoC. The i.MX 7 has a slightly different
clock architecture requiring only two clocks to be referenced.
The IP is slightly different compared to i.MX 6, but currently none
of this differences are in use, therefore reuse GPMI_IS_MX6.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Stefan Agner [Sat, 22 Apr 2017 01:23:34 +0000 (18:23 -0700)]
mtd: nand: gpmi: unify clock handling
Add device specific list of clocks required, and handle all clocks
in a single for loop. This avoids further code duplication when
adding i.MX 7 support.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Pavel Machek [Fri, 21 Apr 2017 10:51:07 +0000 (12:51 +0200)]
mtd: nand: Optimize checking of erased buffers
If we see ~0UL in flash, there's no need for hweight, and no need to
check number of bitflips. So this should be net win.
Signed-off-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Thomas Petazzoni [Sat, 29 Apr 2017 09:06:46 +0000 (11:06 +0200)]
mtd: nand: fsmc_nand: handle on-die ECC case
This commit adjusts the fsmc_nand driver so that it accepts the
NAND_ECC_ON_DIE case. It simply does nothing in this case, since both
the ECC operations and OOB layout will be defined by the NAND chip code
rather than by the NAND controller code.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Thomas Petazzoni [Sat, 29 Apr 2017 09:06:45 +0000 (11:06 +0200)]
mtd: nand: add support for Micron on-die ECC
Now that the core NAND subsystem has support for on-die ECC, this commit
brings the necessary code to support on-die ECC on Micron NANDs.
In micron_nand_init(), we detect if the Micron NAND chip supports on-die
ECC mode, by checking a number of conditions:
- It must be an ONFI NAND
- It must be a SLC NAND
- Enabling *and* disabling on-die ECC must work
- The on-die ECC must be correcting 4 bits per 512 bytes of data. Some
Micron NAND chips have an on-die ECC able to correct 8 bits per 512
bytes of data, but they work slightly differently and therefore we
don't support them in this patch.
Then, if the on-die ECC cannot be disabled (some Micron NAND have on-die
ECC forcefully enabled), we bail out, as we don't support such
NANDs. Indeed, the implementation of raw_read()/raw_write() make the
assumption that on-die ECC can be disabled. Support for Micron NANDs
with on-die ECC forcefully enabled can easily be added, but in the
absence of such HW for testing, we preferred to simply bail out.
If the on-die ECC is supported, and requested in the Device Tree, then
it is indeed enabled, by using custom implementations of the
->read_page(), ->read_page_raw(), ->write_page() and ->write_page_raw()
operation to properly handle the on-die ECC.
In the non-raw functions, we need to enable the internal ECC engine
before issuing the NAND_CMD_READ0 or NAND_CMD_SEQIN commands, which is
why we set the NAND_ECC_CUSTOM_PAGE_ACCESS option at initialization
time (it asks the NAND core to let the NAND driver issue those
commands).
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Boris Brezillon [Fri, 26 May 2017 15:10:15 +0000 (17:10 +0200)]
mtd: nand: Make sure drivers not supporting SET/GET_FEATURES return -ENOTSUPP
A lot of drivers are providing their own ->cmdfunc(), and most of the
time this implementation does not support all possible NAND operations.
But since ->cmdfunc() cannot return an error code, the core has no way
to know that the operation it requested is not supported.
This is a problem we cannot address for all kind of operations with the
current design, but we can prevent these silent failures for the
GET/SET FEATURES operation by overloading the default
->onfi_{set,get}_features() methods with one returning -ENOTSUPP.
Reported-by: Chris Packham <Chris.Packham@alliedtelesis.co.nz>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Tested-by: Chris Packham <Chris.Packham@alliedtelesis.co.nz>
Thomas Petazzoni [Sat, 29 Apr 2017 09:06:44 +0000 (11:06 +0200)]
mtd: nand: export nand_{read,write}_page_raw()
The nand_read_page_raw() and nand_write_page_raw() functions might be
re-used by vendor-specific implementations of the read_page/write_page
functions. Instead of having vendor-specific code duplicate this code,
it is much better to export those functions and allow them to be
re-used.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Thomas Petazzoni [Sat, 29 Apr 2017 09:06:43 +0000 (11:06 +0200)]
mtd: nand: add core support for on-die ECC
A number of NAND flashes have a capability called "on-die ECC" where the
NAND chip itself is capable of detecting and correcting errors.
Linux already has support for using the ECC implementation of the NAND
controller, or a software based ECC implementation, but not for using
the ECC implementation of the NAND controller. However, such an
implementation is sometimes useful in situations where the NAND
controller provides ECC algorithms that are not strong enough for the
NAND chip used on the system. A typical case is a NAND chip that
requires a 4-bit ECC, while the NAND controller only provides a 1-bit
ECC algorithm.
This commit introduces the support for the NAND_ECC_ON_DIE ECC mode:
- Parsing of the "on-die" value for the "nand-ecc-mode" Device Tree
property
- Handling NAND_ECC_ON_DIE case in nand_scan_tail(). The idea is that
the vendor specific code for the NAND chip must implement
->read_page() and ->write_page(). It may optionally provide its own
->read_page_raw() and ->write_page_raw() as well. For OOB operation,
we assume the standard operations are good enough, but they can be
overridden by the vendor specific code if needed.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Thomas Petazzoni [Sat, 29 Apr 2017 09:06:42 +0000 (11:06 +0200)]
dt-bindings: mtd: document new "on-die" nand-ecc-mode
A number of NAND chips support a feature called on-die ECC, where the
NAND chip itself is capable of doing error detection and correction. The
new "on-die" value for nand-ecc-mode indicates that we want this
functionality to be used.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Thomas Petazzoni [Sat, 29 Apr 2017 08:52:36 +0000 (10:52 +0200)]
mtd: nand: fsmc: remove default timings
When timings are no longer provided by the Device Tree, we now use the
SDR timings specified by the NAND flash, and such SDR timings are always
provided. Therefore, it is no longer necessary to keep "default" timings
in the fmsc driver.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Thomas Petazzoni [Sat, 29 Apr 2017 08:52:35 +0000 (10:52 +0200)]
mtd: nand: fsmc: add support for SDR timings
Until now, the fsmc_nand driver was either using controller timings
specified in the Device Tree (through FSMC specific DT properties) or
alternatively default/fallback timings.
This commit implements support to use the timings advertised by the NAND
chip itself, by implementing the ->setup_data_interface() hook. To
preserve backward compatibility, if timings are specified in the Device
Tree, we use the timings from the Device Tree (and don't implement
->setup_data_interface).
Many thanks to Boris Brezillon for coming up with the logic to convert
the NAND chip timings into the timings expected by the FSMC controller.
Also, since the timings are now not only coming from the DT, the message
warning that default timings will be used is removed.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Thomas Petazzoni [Sat, 29 Apr 2017 08:52:34 +0000 (10:52 +0200)]
mtd: nand: fsmc: reduce number of arguments of fsmc_nand_setup()
In preparation for the introduction of support for using SDR timings
exposed by the NAND flash instead of hard-coded timings, this commit
reworks the fsmc_nand_setup() function to take a "struct fsmc_nand_data"
as argument, which already contains the I/O registers base address, bank
and bus width information.
The timings is also currently contained in the "struct fsmc_nand_data",
but we still pass it as a separate argument because the support for
using SDR timings will pass a different value.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Alexander Couzens [Tue, 2 May 2017 09:47:36 +0000 (11:47 +0200)]
mtd: nand: davinci: set ECC algorithm explicitly for HW based ECC
If ECC strength is 4bits/512bytes the algorithm of the ECC engine is
BCH, otherwise (1bit/512bytes) Hamming is used.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Boris Brezillon [Tue, 2 May 2017 10:29:13 +0000 (12:29 +0200)]
mtd: nand: jz4780: Use mtd_set_ooblayout() to set the ooblayout
The mtd_set_ooblayout() accesor has been added to hide internals of
mtd_info and ease future refactoring. Call mtd_set_ooblayout() instead of
directly accessing mtd->ooblayout.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Harvey Hunt <harveyhuntnexus@gmail.com>
Ezequiel Garcia [Tue, 2 May 2017 19:49:52 +0000 (16:49 -0300)]
mtd: nand: Add Mediatek machine dependency
The Mediatek NAND driver is only needed for a specific
platform, so avoid cluttering the configuration.
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Ezequiel Garcia [Tue, 2 May 2017 19:49:51 +0000 (16:49 -0300)]
mtd: nand: Add Hisilicon machine dependency
The Hisilicon NAND driver is only needed for a specific
platform, so avoid cluttering the configuration.
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Linus Torvalds [Sat, 13 May 2017 20:19:49 +0000 (13:19 -0700)]
Linux 4.12-rc1
Linus Torvalds [Sat, 13 May 2017 17:25:05 +0000 (10:25 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/dtor/input
Pull some more input subsystem updates from Dmitry Torokhov:
"An updated xpad driver with a few more recognized device IDs, and a
new psxpad-spi driver, allowing connecting Playstation 1 and 2 joypads
via SPI bus"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: cros_ec_keyb - remove extraneous 'const'
Input: add support for PlayStation 1/2 joypads connected via SPI
Input: xpad - add USB IDs for Mad Catz Brawlstick and Razer Sabertooth
Input: xpad - sync supported devices with xboxdrv
Input: xpad - sort supported devices by USB ID
Linus Torvalds [Sat, 13 May 2017 17:23:12 +0000 (10:23 -0700)]
Merge tag 'upstream-4.12-rc1' of git://git.infradead.org/linux-ubifs
Pull UBI/UBIFS updates from Richard Weinberger:
- new config option CONFIG_UBIFS_FS_SECURITY
- minor improvements
- random fixes
* tag 'upstream-4.12-rc1' of git://git.infradead.org/linux-ubifs:
ubi: Add debugfs file for tracking PEB state
ubifs: Fix a typo in comment of ioctl2ubifs & ubifs2ioctl
ubifs: Remove unnecessary assignment
ubifs: Fix cut and paste error on sb type comparisons
ubi: fastmap: Fix slab corruption
ubifs: Add CONFIG_UBIFS_FS_SECURITY to disable/enable security labels
ubi: Make mtd parameter readable
ubi: Fix section mismatch
Linus Torvalds [Sat, 13 May 2017 17:20:02 +0000 (10:20 -0700)]
Merge branch 'for-linus-4.12-rc1' of git://git./linux/kernel/git/rw/uml
Pull UML fixes from Richard Weinberger:
"No new stuff, just fixes"
* 'for-linus-4.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/uml:
um: Add missing NR_CPUS include
um: Fix to call read_initrd after init_bootmem
um: Include kbuild.h instead of duplicating its macros
um: Fix PTRACE_POKEUSER on x86_64
um: Set number of CPUs
um: Fix _print_addr()
Linus Torvalds [Sat, 13 May 2017 16:49:35 +0000 (09:49 -0700)]
Merge branch 'akpm' (patches from Andrew)
Merge misc fixes from Andrew Morton:
"15 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
mm, docs: update memory.stat description with workingset* entries
mm: vmscan: scan until it finds eligible pages
mm, thp: copying user pages must schedule on collapse
dax: fix PMD data corruption when fault races with write
dax: fix data corruption when fault races with write
ext4: return to starting transaction in ext4_dax_huge_fault()
mm: fix data corruption due to stale mmap reads
dax: prevent invalidation of mapped DAX entries
Tigran has moved
mm, vmalloc: fix vmalloc users tracking properly
mm/khugepaged: add missed tracepoint for collapse_huge_page_swapin
gcov: support GCC 7.1
mm, vmstat: Remove spurious WARN() during zoneinfo print
time: delete current_fs_time()
hwpoison, memcg: forcibly uncharge LRU pages
Roman Gushchin [Fri, 12 May 2017 22:47:09 +0000 (15:47 -0700)]
mm, docs: update memory.stat description with workingset* entries
Commit
4b4cea91691d ("mm: vmscan: fix IO/refault regression in cache
workingset transition") introduced three new entries in memory stat
file:
- workingset_refault
- workingset_activate
- workingset_nodereclaim
This commit adds a corresponding description to the cgroup v2 docs.
Link: http://lkml.kernel.org/r/1494530293-31236-1-git-send-email-guro@fb.com
Signed-off-by: Roman Gushchin <guro@fb.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Vladimir Davydov <vdavydov.dev@gmail.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Li Zefan <lizefan@huawei.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Minchan Kim [Fri, 12 May 2017 22:47:06 +0000 (15:47 -0700)]
mm: vmscan: scan until it finds eligible pages
Although there are a ton of free swap and anonymous LRU page in elgible
zones, OOM happened.
balloon invoked oom-killer: gfp_mask=0x17080c0(GFP_KERNEL_ACCOUNT|__GFP_ZERO|__GFP_NOTRACK), nodemask=(null), order=0, oom_score_adj=0
CPU: 7 PID: 1138 Comm: balloon Not tainted
4.11.0-rc6-mm1-zram-00289-ge228d67e9677-dirty #17
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Ubuntu-1.8.2-1ubuntu1 04/01/2014
Call Trace:
oom_kill_process+0x21d/0x3f0
out_of_memory+0xd8/0x390
__alloc_pages_slowpath+0xbc1/0xc50
__alloc_pages_nodemask+0x1a5/0x1c0
pte_alloc_one+0x20/0x50
__pte_alloc+0x1e/0x110
__handle_mm_fault+0x919/0x960
handle_mm_fault+0x77/0x120
__do_page_fault+0x27a/0x550
trace_do_page_fault+0x43/0x150
do_async_page_fault+0x2c/0x90
async_page_fault+0x28/0x30
Mem-Info:
active_anon:424716 inactive_anon:65314 isolated_anon:0
active_file:52 inactive_file:46 isolated_file:0
unevictable:0 dirty:27 writeback:0 unstable:0
slab_reclaimable:3967 slab_unreclaimable:4125
mapped:133 shmem:43 pagetables:1674 bounce:0
free:4637 free_pcp:225 free_cma:0
Node 0 active_anon:1698864kB inactive_anon:261256kB active_file:208kB inactive_file:184kB unevictable:0kB isolated(anon):0kB isolated(file):0kB mapped:532kB dirty:108kB writeback:0kB shmem:172kB writeback_tmp:0kB unstable:0kB all_unreclaimable? no
DMA free:7316kB min:32kB low:44kB high:56kB active_anon:8064kB inactive_anon:0kB active_file:0kB inactive_file:0kB unevictable:0kB writepending:0kB present:15992kB managed:15908kB mlocked:0kB slab_reclaimable:464kB slab_unreclaimable:40kB kernel_stack:0kB pagetables:24kB bounce:0kB free_pcp:0kB local_pcp:0kB free_cma:0kB
lowmem_reserve[]: 0 992 992 1952
DMA32 free:9088kB min:2048kB low:3064kB high:4080kB active_anon:952176kB inactive_anon:0kB active_file:36kB inactive_file:0kB unevictable:0kB writepending:88kB present:1032192kB managed:1019388kB mlocked:0kB slab_reclaimable:13532kB slab_unreclaimable:16460kB kernel_stack:3552kB pagetables:6672kB bounce:0kB free_pcp:56kB local_pcp:24kB free_cma:0kB
lowmem_reserve[]: 0 0 0 959
Movable free:3644kB min:1980kB low:2960kB high:3940kB active_anon:738560kB inactive_anon:261340kB active_file:188kB inactive_file:640kB unevictable:0kB writepending:20kB present:1048444kB managed:1010816kB mlocked:0kB slab_reclaimable:0kB slab_unreclaimable:0kB kernel_stack:0kB pagetables:0kB bounce:0kB free_pcp:832kB local_pcp:60kB free_cma:0kB
lowmem_reserve[]: 0 0 0 0
DMA: 1*4kB (E) 0*8kB 18*16kB (E) 10*32kB (E) 10*64kB (E) 9*128kB (ME) 8*256kB (E) 2*512kB (E) 2*1024kB (E) 0*2048kB 0*4096kB = 7524kB
DMA32: 417*4kB (UMEH) 181*8kB (UMEH) 68*16kB (UMEH) 48*32kB (UMEH) 14*64kB (MH) 3*128kB (M) 1*256kB (H) 1*512kB (M) 2*1024kB (M) 0*2048kB 0*4096kB = 9836kB
Movable: 1*4kB (M) 1*8kB (M) 1*16kB (M) 1*32kB (M) 0*64kB 1*128kB (M) 2*256kB (M) 4*512kB (M) 1*1024kB (M) 0*2048kB 0*4096kB = 3772kB
378 total pagecache pages
17 pages in swap cache
Swap cache stats: add 17325, delete 17302, find 0/27
Free swap = 978940kB
Total swap = 1048572kB
524157 pages RAM
0 pages HighMem/MovableOnly
12629 pages reserved
0 pages cma reserved
0 pages hwpoisoned
[ pid ] uid tgid total_vm rss nr_ptes nr_pmds swapents oom_score_adj name
[ 433] 0 433 4904 5 14 3 82 0 upstart-udev-br
[ 438] 0 438 12371 5 27 3 191 -1000 systemd-udevd
With investigation, skipping page of isolate_lru_pages makes reclaim
void because it returns zero nr_taken easily so LRU shrinking is
effectively nothing and just increases priority aggressively. Finally,
OOM happens.
The problem is that get_scan_count determines nr_to_scan with eligible
zones so although priority drops to zero, it couldn't reclaim any pages
if the LRU contains mostly ineligible pages.
get_scan_count:
size = lruvec_lru_size(lruvec, lru, sc->reclaim_idx);
size = size >> sc->priority;
Assumes sc->priority is 0 and LRU list is as follows.
N-N-N-N-H-H-H-H-H-H-H-H-H-H-H-H-H-H-H-H
(Ie, small eligible pages are in the head of LRU but others are
almost ineligible pages)
In that case, size becomes 4 so VM want to scan 4 pages but 4 pages from
tail of the LRU are not eligible pages. If get_scan_count counts
skipped pages, it doesn't reclaim any pages remained after scanning 4
pages so it ends up OOM happening.
This patch makes isolate_lru_pages try to scan pages until it encounters
eligible zones's pages.
[akpm@linux-foundation.org: clean up mind-bending `for' statement. Tweak comment text]
Fixes: 3db65812d688 ("Revert "mm, vmscan: account for skipped pages as a partial scan"")
Link: http://lkml.kernel.org/r/1494457232-27401-1-git-send-email-minchan@kernel.org
Signed-off-by: Minchan Kim <minchan@kernel.org>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Mel Gorman <mgorman@techsingularity.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David Rientjes [Fri, 12 May 2017 22:47:03 +0000 (15:47 -0700)]
mm, thp: copying user pages must schedule on collapse
We have encountered need_resched warnings in __collapse_huge_page_copy()
while doing {clear,copy}_user_highpage() over HPAGE_PMD_NR source pages.
mm->mmap_sem is held for write, but the iteration is well bounded.
Reschedule as needed.
Link: http://lkml.kernel.org/r/alpine.DEB.2.10.1705101426380.109808@chino.kir.corp.google.com
Signed-off-by: David Rientjes <rientjes@google.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Mel Gorman <mgorman@techsingularity.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ross Zwisler [Fri, 12 May 2017 22:47:00 +0000 (15:47 -0700)]
dax: fix PMD data corruption when fault races with write
This is based on a patch from Jan Kara that fixed the equivalent race in
the DAX PTE fault path.
Currently DAX PMD read fault can race with write(2) in the following
way:
CPU1 - write(2) CPU2 - read fault
dax_iomap_pmd_fault()
->iomap_begin() - sees hole
dax_iomap_rw()
iomap_apply()
->iomap_begin - allocates blocks
dax_iomap_actor()
invalidate_inode_pages2_range()
- there's nothing to invalidate
grab_mapping_entry()
- we add huge zero page to the radix tree
and map it to page tables
The result is that hole page is mapped into page tables (and thus zeros
are seen in mmap) while file has data written in that place.
Fix the problem by locking exception entry before mapping blocks for the
fault. That way we are sure invalidate_inode_pages2_range() call for
racing write will either block on entry lock waiting for the fault to
finish (and unmap stale page tables after that) or read fault will see
already allocated blocks by write(2).
Fixes: 9f141d6ef6258 ("dax: Call ->iomap_begin without entry lock during dax fault")
Link: http://lkml.kernel.org/r/20170510172700.18991-1-ross.zwisler@linux.intel.com
Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jan Kara [Fri, 12 May 2017 22:46:57 +0000 (15:46 -0700)]
dax: fix data corruption when fault races with write
Currently DAX read fault can race with write(2) in the following way:
CPU1 - write(2) CPU2 - read fault
dax_iomap_pte_fault()
->iomap_begin() - sees hole
dax_iomap_rw()
iomap_apply()
->iomap_begin - allocates blocks
dax_iomap_actor()
invalidate_inode_pages2_range()
- there's nothing to invalidate
grab_mapping_entry()
- we add zero page in the radix tree
and map it to page tables
The result is that hole page is mapped into page tables (and thus zeros
are seen in mmap) while file has data written in that place.
Fix the problem by locking exception entry before mapping blocks for the
fault. That way we are sure invalidate_inode_pages2_range() call for
racing write will either block on entry lock waiting for the fault to
finish (and unmap stale page tables after that) or read fault will see
already allocated blocks by write(2).
Fixes: 9f141d6ef6258a3a37a045842d9ba7e68f368956
Link: http://lkml.kernel.org/r/20170510085419.27601-5-jack@suse.cz
Signed-off-by: Jan Kara <jack@suse.cz>
Reviewed-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jan Kara [Fri, 12 May 2017 22:46:54 +0000 (15:46 -0700)]
ext4: return to starting transaction in ext4_dax_huge_fault()
DAX will return to locking exceptional entry before mapping blocks for a
page fault to fix possible races with concurrent writes. To avoid lock
inversion between exceptional entry lock and transaction start, start
the transaction already in ext4_dax_huge_fault().
Fixes: 9f141d6ef6258a3a37a045842d9ba7e68f368956
Link: http://lkml.kernel.org/r/20170510085419.27601-4-jack@suse.cz
Signed-off-by: Jan Kara <jack@suse.cz>
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jan Kara [Fri, 12 May 2017 22:46:50 +0000 (15:46 -0700)]
mm: fix data corruption due to stale mmap reads
Currently, we didn't invalidate page tables during invalidate_inode_pages2()
for DAX. That could result in e.g. 2MiB zero page being mapped into
page tables while there were already underlying blocks allocated and
thus data seen through mmap were different from data seen by read(2).
The following sequence reproduces the problem:
- open an mmap over a 2MiB hole
- read from a 2MiB hole, faulting in a 2MiB zero page
- write to the hole with write(3p). The write succeeds but we
incorrectly leave the 2MiB zero page mapping intact.
- via the mmap, read the data that was just written. Since the zero
page mapping is still intact we read back zeroes instead of the new
data.
Fix the problem by unconditionally calling invalidate_inode_pages2_range()
in dax_iomap_actor() for new block allocations and by properly
invalidating page tables in invalidate_inode_pages2_range() for DAX
mappings.
Fixes: c6dcf52c23d2d3fb5235cec42d7dd3f786b87d55
Link: http://lkml.kernel.org/r/20170510085419.27601-3-jack@suse.cz
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ross Zwisler [Fri, 12 May 2017 22:46:47 +0000 (15:46 -0700)]
dax: prevent invalidation of mapped DAX entries
Patch series "mm,dax: Fix data corruption due to mmap inconsistency",
v4.
This series fixes data corruption that can happen for DAX mounts when
page faults race with write(2) and as a result page tables get out of
sync with block mappings in the filesystem and thus data seen through
mmap is different from data seen through read(2).
The series passes testing with t_mmap_stale test program from Ross and
also other mmap related tests on DAX filesystem.
This patch (of 4):
dax_invalidate_mapping_entry() currently removes DAX exceptional entries
only if they are clean and unlocked. This is done via:
invalidate_mapping_pages()
invalidate_exceptional_entry()
dax_invalidate_mapping_entry()
However, for page cache pages removed in invalidate_mapping_pages()
there is an additional criteria which is that the page must not be
mapped. This is noted in the comments above invalidate_mapping_pages()
and is checked in invalidate_inode_page().
For DAX entries this means that we can can end up in a situation where a
DAX exceptional entry, either a huge zero page or a regular DAX entry,
could end up mapped but without an associated radix tree entry. This is
inconsistent with the rest of the DAX code and with what happens in the
page cache case.
We aren't able to unmap the DAX exceptional entry because according to
its comments invalidate_mapping_pages() isn't allowed to block, and
unmap_mapping_range() takes a write lock on the mapping->i_mmap_rwsem.
Since we essentially never have unmapped DAX entries to evict from the
radix tree, just remove dax_invalidate_mapping_entry().
Fixes: c6dcf52c23d2 ("mm: Invalidate DAX radix tree entries only if appropriate")
Link: http://lkml.kernel.org/r/20170510085419.27601-2-jack@suse.cz
Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Reported-by: Jan Kara <jack@suse.cz>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: <stable@vger.kernel.org> [4.10+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andrew Morton [Fri, 12 May 2017 22:46:44 +0000 (15:46 -0700)]
Tigran has moved
Cc: Tigran Aivazian <aivazian.tigran@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Michal Hocko [Fri, 12 May 2017 22:46:41 +0000 (15:46 -0700)]
mm, vmalloc: fix vmalloc users tracking properly
Commit
1f5307b1e094 ("mm, vmalloc: properly track vmalloc users") has
pulled asm/pgtable.h include dependency to linux/vmalloc.h and that
turned out to be a bad idea for some architectures. E.g. m68k fails
with
In file included from arch/m68k/include/asm/pgtable_mm.h:145:0,
from arch/m68k/include/asm/pgtable.h:4,
from include/linux/vmalloc.h:9,
from arch/m68k/kernel/module.c:9:
arch/m68k/include/asm/mcf_pgtable.h: In function 'nocache_page':
>> arch/m68k/include/asm/mcf_pgtable.h:339:43: error: 'init_mm' undeclared (first use in this function)
#define pgd_offset_k(address) pgd_offset(&init_mm, address)
as spotted by kernel build bot. nios2 fails for other reason
In file included from include/asm-generic/io.h:767:0,
from arch/nios2/include/asm/io.h:61,
from include/linux/io.h:25,
from arch/nios2/include/asm/pgtable.h:18,
from include/linux/mm.h:70,
from include/linux/pid_namespace.h:6,
from include/linux/ptrace.h:9,
from arch/nios2/include/uapi/asm/elf.h:23,
from arch/nios2/include/asm/elf.h:22,
from include/linux/elf.h:4,
from include/linux/module.h:15,
from init/main.c:16:
include/linux/vmalloc.h: In function '__vmalloc_node_flags':
include/linux/vmalloc.h:99:40: error: 'PAGE_KERNEL' undeclared (first use in this function); did you mean 'GFP_KERNEL'?
which is due to the newly added #include <asm/pgtable.h>, which on nios2
includes <linux/io.h> and thus <asm/io.h> and <asm-generic/io.h> which
again includes <linux/vmalloc.h>.
Tweaking that around just turns out a bigger headache than necessary.
This patch reverts
1f5307b1e094 and reimplements the original fix in a
different way. __vmalloc_node_flags can stay static inline which will
cover vmalloc* functions. We only have one external user
(kvmalloc_node) and we can export __vmalloc_node_flags_caller and
provide the caller directly. This is much simpler and it doesn't really
need any games with header files.
[akpm@linux-foundation.org: coding-style fixes]
[mhocko@kernel.org: revert old comment]
Link: http://lkml.kernel.org/r/20170509211054.GB16325@dhcp22.suse.cz
Fixes: 1f5307b1e094 ("mm, vmalloc: properly track vmalloc users")
Link: http://lkml.kernel.org/r/20170509153702.GR6481@dhcp22.suse.cz
Signed-off-by: Michal Hocko <mhocko@suse.com>
Cc: Tobias Klauser <tklauser@distanz.ch>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
SeongJae Park [Fri, 12 May 2017 22:46:38 +0000 (15:46 -0700)]
mm/khugepaged: add missed tracepoint for collapse_huge_page_swapin
One return case of `__collapse_huge_page_swapin()` does not invoke
tracepoint while every other return case does. This commit adds a
tracepoint invocation for the case.
Link: http://lkml.kernel.org/r/20170507101813.30187-1-sj38.park@gmail.com
Signed-off-by: SeongJae Park <sj38.park@gmail.com>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Martin Liska [Fri, 12 May 2017 22:46:35 +0000 (15:46 -0700)]
gcov: support GCC 7.1
Starting from GCC 7.1, __gcov_exit is a new symbol expected to be
implemented in a profiling runtime.
[akpm@linux-foundation.org: coding-style fixes]
[mliska@suse.cz: v2]
Link: http://lkml.kernel.org/r/e63a3c59-0149-c97e-4084-20ca8f146b26@suse.cz
Link: http://lkml.kernel.org/r/8c4084fa-3885-29fe-5fc4-0d4ca199c785@suse.cz
Signed-off-by: Martin Liska <mliska@suse.cz>
Acked-by: Peter Oberparleiter <oberpar@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Reza Arbab [Fri, 12 May 2017 22:46:32 +0000 (15:46 -0700)]
mm, vmstat: Remove spurious WARN() during zoneinfo print
After commit
e2ecc8a79ed4 ("mm, vmstat: print non-populated zones in
zoneinfo"), /proc/zoneinfo will show unpopulated zones.
A memoryless node, having no populated zones at all, was previously
ignored, but will now trigger the WARN() in is_zone_first_populated().
Remove this warning, as its only purpose was to warn of a situation that
has since been enabled.
Aside: The "per-node stats" are still printed under the first populated
zone, but that's not necessarily the first stanza any more. I'm not
sure which criteria is more important with regard to not breaking
parsers, but it looks a little weird to the eye.
Fixes: e2ecc8a79ed4 ("mm, vmstat: print node-based stats in zoneinfo file")
Link: http://lkml.kernel.org/r/1493854905-10918-1-git-send-email-arbab@linux.vnet.ibm.com
Signed-off-by: Reza Arbab <arbab@linux.vnet.ibm.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Deepa Dinamani [Fri, 12 May 2017 22:46:29 +0000 (15:46 -0700)]
time: delete current_fs_time()
All uses of the current_fs_time() function have been replaced by other
time interfaces.
And, its use cases can be fulfilled by current_time() or ktime_get_*
variants.
Link: http://lkml.kernel.org/r/1491613030-11599-13-git-send-email-deepa.kernel@gmail.com
Signed-off-by: Deepa Dinamani <deepa.kernel@gmail.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Michal Hocko [Fri, 12 May 2017 22:46:26 +0000 (15:46 -0700)]
hwpoison, memcg: forcibly uncharge LRU pages
Laurent Dufour has noticed that hwpoinsoned pages are kept charged. In
his particular case he has hit a bad_page("page still charged to
cgroup") when onlining a hwpoison page. While this looks like something
that shouldn't happen in the first place because onlining hwpages and
returning them to the page allocator makes only little sense it shows a
real problem.
hwpoison pages do not get freed usually so we do not uncharge them (at
least not since commit
0a31bc97c80c ("mm: memcontrol: rewrite uncharge
API")). Each charge pins memcg (since
e8ea14cc6ead ("mm: memcontrol:
take a css reference for each charged page")) as well and so the
mem_cgroup and the associated state will never go away. Fix this leak
by forcibly uncharging a LRU hwpoisoned page in delete_from_lru_cache().
We also have to tweak uncharge_list because it cannot rely on zero ref
count for these pages.
[akpm@linux-foundation.org: coding-style fixes]
Fixes: 0a31bc97c80c ("mm: memcontrol: rewrite uncharge API")
Link: http://lkml.kernel.org/r/20170502185507.GB19165@dhcp22.suse.cz
Signed-off-by: Michal Hocko <mhocko@suse.com>
Reported-by: Laurent Dufour <ldufour@linux.vnet.ibm.com>
Tested-by: Laurent Dufour <ldufour@linux.vnet.ibm.com>
Reviewed-by: Balbir Singh <bsingharora@gmail.com>
Reviewed-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Fri, 12 May 2017 22:43:10 +0000 (15:43 -0700)]
Merge branch 'libnvdimm-fixes' of git://git./linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm fixes from Dan Williams:
"Incremental fixes and a small feature addition on top of the main
libnvdimm 4.12 pull request:
- Geert noticed that tinyconfig was bloated by BLOCK selecting DAX.
The size regression is fixed by moving all dax helpers into the
dax-core and only specifying "select DAX" for FS_DAX and
dax-capable drivers. He also asked for clarification of the
NR_DEV_DAX config option which, on closer look, does not need to be
a config option at all. Mike also throws in a DEV_DAX_PMEM fixup
for good measure.
- Ben's attention to detail on -stable patch submissions caught a
case where the recent fixes to arch_copy_from_iter_pmem() missed a
condition where we strand dirty data in the cache. This is tagged
for -stable and will also be included in the rework of the pmem api
to a proposed {memcpy,copy_user}_flushcache() interface for 4.13.
- Vishal adds a feature that missed the initial pull due to pending
review feedback. It allows the kernel to clear media errors when
initializing a BTT (atomic sector update driver) instance on a pmem
namespace.
- Ross noticed that the dax_device + dax_operations conversion broke
__dax_zero_page_range(). The nvdimm unit tests fail to check this
path, but xfstests immediately trips over it. No excuse for missing
this before submitting the 4.12 pull request.
These all pass the nvdimm unit tests and an xfstests spot check. The
set has received a build success notification from the kbuild robot"
* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
filesystem-dax: fix broken __dax_zero_page_range() conversion
libnvdimm, btt: ensure that initializing metadata clears poison
libnvdimm: add an atomic vs process context flag to rw_bytes
x86, pmem: Fix cache flushing for iovec write < 8 bytes
device-dax: kill NR_DEV_DAX
block, dax: move "select DAX" from BLOCK to FS_DAX
device-dax: Tell kbuild DEV_DAX_PMEM depends on DEV_DAX
Linus Torvalds [Fri, 12 May 2017 19:10:38 +0000 (12:10 -0700)]
Merge tag 'sound-fix-4.12-rc1' of git://git./linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"This contains a one-liner change that has a significant impact:
disabling the build of OSS. It's been unmaintained for long time, and
we'd like to drop the stuff. Finally, as the first step, stop the
build. Let's see whether it works without much complaints.
Other than that, there are two small fixes for HD-audio"
* tag 'sound-fix-4.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
sound: Disable the build of OSS drivers
ALSA: hda: Fix cpu lockup when stopping the cmd dmas
ALSA: hda - Add mute led support for HP EliteBook 840 G3
Linus Torvalds [Fri, 12 May 2017 19:02:21 +0000 (12:02 -0700)]
Merge tag 'for-v4.12-2' of git://git./linux/kernel/git/sre/linux-power-supply
Pull more power-supply updates from Sebastian Reichel:
"The power-supply subsystem has a few more changes for the v4.12 merge
window:
- New battery driver for AXP20X and AXP22X PMICs
- Improve max17042_battery for usage on x86
- Misc small cleanups & fixes"
* tag 'for-v4.12-2' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply: (34 commits)
power: supply: cpcap-charger: Keep trickle charger bits disabled
power: supply: cpcap-charger: Fix enable for 3.8V charge setting
power: supply: cpcap-charger: Fix charge voltage configuration
power: supply: cpcap-charger: Fix charger name
power: supply: twl4030-charger: make twl4030_bci_property_is_writeable static
power: supply: sbs-battery: Add alert callback
mailmap: add Sebastian Reichel
power: supply: avoid unused twl4030-madc.h
power: supply: sbs-battery: Correct supply status with current draw
power: supply: sbs-battery: Don't ignore the first external power change
power: supply: pda_power: move from timer to delayed_work
power: supply: max17042_battery: Add support for the SCOPE property
power: supply: max17042_battery: Add support for the CHARGE_NOW property
power: supply: max17042_battery: Add support for the CHARGE_FULL_DESIGN property
power: supply: max17042_battery: mAh readings depend on r_sns value
power: supply: max17042_battery: Add support for the VOLT_MIN property
power: supply: max17042_battery: Add support for the TECHNOLOGY attribute
power: supply: max17042_battery: Add external_power_changed callback
power: supply: max17042_battery: Add support for the STATUS property
power: supply: max17042_battery: Add default platform_data fallback data
...
Linus Torvalds [Fri, 12 May 2017 18:58:45 +0000 (11:58 -0700)]
Merge branch 'next' of git://git./linux/kernel/git/rzhang/linux
Pull thermal management updates from Zhang Rui:
- Fix a problem where orderly_shutdown() is called for multiple times
due to multiple critical overheating events raised in a short period
by platform thermal driver. (Keerthy)
- Introduce a backup thermal shutdown mechanism, which invokes
kernel_power_off()/emergency_restart() directly, after
orderly_shutdown() being issued for certain amount of time(specified
via Kconfig). This is useful in certain conditions that userspace may
be unable to power off the system in a clean manner and leaves the
system in a critical state, like in the middle of driver probing
phase. (Keerthy)
- Introduce a new interface in thermal devfreq_cooling code so that the
driver can provide more precise data regarding actual power to the
thermal governor every time the power budget is calculated. (Lukasz
Luba)
- Introduce BCM 2835 soc thermal driver and northstar thermal driver,
within a new sub-folder. (Rafał Miłecki)
- Introduce DA9062/61 thermal driver. (Steve Twiss)
- Remove non-DT booting on TI-SoC driver. Also add support to fetching
coefficients from DT. (Keerthy)
- Refactorf RCAR Gen3 thermal driver. (Niklas Söderlund)
- Small fix on MTK and intel-soc-dts thermal driver. (Dawei Chien,
Brian Bian)
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux: (25 commits)
thermal: core: Add a back up thermal shutdown mechanism
thermal: core: Allow orderly_poweroff to be called only once
Thermal: Intel SoC DTS: Change interrupt request behavior
trace: thermal: add another parameter 'power' to the tracing function
thermal: devfreq_cooling: add new interface for direct power read
thermal: devfreq_cooling: refactor code and add get_voltage function
thermal: mt8173: minor mtk_thermal.c cleanups
thermal: bcm2835: move to the broadcom subdirectory
thermal: broadcom: ns: specify myself as MODULE_AUTHOR
thermal: da9062/61: Thermal junction temperature monitoring driver
Documentation: devicetree: thermal: da9062/61 TJUNC temperature binding
thermal: broadcom: add Northstar thermal driver
dt-bindings: thermal: add support for Broadcom's Northstar thermal
thermal: bcm2835: add thermal driver for bcm2835 SoC
dt-bindings: Add thermal zone to bcm2835-thermal example
thermal: rcar_gen3_thermal: add suspend and resume support
thermal: rcar_gen3_thermal: store device match data in private structure
thermal: rcar_gen3_thermal: enable hardware interrupts for trip points
thermal: rcar_gen3_thermal: record and check number of TSCs found
thermal: rcar_gen3_thermal: check that TSC exists before memory allocation
...
Linus Torvalds [Fri, 12 May 2017 18:48:26 +0000 (11:48 -0700)]
Merge tag 'drm-fixes-for-v4.12-rc1' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"AMD, nouveau, one i915, and one EDID fix for v4.12-rc1
Some fixes that it would be good to have in rc1. It contains the i915
quiet fix that you reported.
It also has an amdgpu fixes pull, with lots of ongoing work on Vega10
which is new in this kernel and is preliminary support so may have a
fair bit of movement.
Otherwise a few non-Vega10 AMD fixes, one EDID fix and some nouveau
regression fixers"
* tag 'drm-fixes-for-v4.12-rc1' of git://people.freedesktop.org/~airlied/linux: (144 commits)
drm/i915: Make vblank evade warnings optional
drm/nouveau/therm: remove ineffective workarounds for alarm bugs
drm/nouveau/tmr: avoid processing completed alarms when adding a new one
drm/nouveau/tmr: fix corruption of the pending list when rescheduling an alarm
drm/nouveau/tmr: handle races with hw when updating the next alarm time
drm/nouveau/tmr: ack interrupt before processing alarms
drm/nouveau/core: fix static checker warning
drm/nouveau/fb/ram/gf100-: remove 0x10f200 read
drm/nouveau/kms/nv50: skip core channel cursor update on position-only changes
drm/nouveau/kms/nv50: fix source-rect-only plane updates
drm/nouveau/kms/nv50: remove pointless argument to window atomic_check_acquire()
drm/amd/powerplay: refine pwm1_enable callback functions for CI.
drm/amd/powerplay: refine pwm1_enable callback functions for vi.
drm/amd/powerplay: refine pwm1_enable callback functions for Vega10.
drm/amdgpu: refine amdgpu pwm1_enable sysfs interface.
drm/amdgpu: add amd fan ctrl mode enums.
drm/amd/powerplay: add more smu message on Vega10.
drm/amdgpu: fix dependency issue
drm/amd: fix init order of sched job
drm/amdgpu: add some additional vega10 pci ids
...
Linus Torvalds [Fri, 12 May 2017 18:44:13 +0000 (11:44 -0700)]
Merge branch 'for-next' of git://git./linux/kernel/git/nab/target-pending
Pull SCSI target updates from Nicholas Bellinger:
"Things were a lot more calm than previously expected. It's primarily
fixes in various areas, with most of the new functionality centering
around TCMU backend driver work that Xiubo Li has been driving.
Here's the summary on the feature side:
- Make T10-PI verify configurable for emulated (FILEIO + RD) backends
(Dmitry Monakhov)
- Allow target-core/TCMU pass-through to use in-kernel SPC-PR logic
(Bryant Ly + MNC)
- Add TCMU support for growing ring buffer size (Xiubo Li + MNC)
- Add TCMU support for global block data pool (Xiubo Li + MNC)
and on the bug-fix side:
- Fix COMPARE_AND_WRITE non GOOD status handling for READ phase
failures (Gary Guo + nab)
- Fix iscsi-target hang with explicitly changing per NodeACL
CmdSN number depth with concurrent login driven session
reinstatement. (Gary Guo + nab)
- Fix ibmvscsis fabric driver ABORT task handling (Bryant Ly)
- Fix target-core/FILEIO zero length handling (Bart Van Assche)
Also, there was an OOPs introduced with the WRITE_VERIFY changes that
I ended up reverting at the last minute, because as not unusual Bart
and I could not agree on the fix in time for -rc1. Since it's specific
to a conformance test, it's been reverted for now.
There is a separate patch in the queue to address the underlying
control CDB write overflow regression in >= v4.3 separate from the
WRITE_VERIFY revert here, that will be pushed post -rc1"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (30 commits)
Revert "target: Fix VERIFY and WRITE VERIFY command parsing"
IB/srpt: Avoid that aborting a command triggers a kernel warning
IB/srpt: Fix abort handling
target/fileio: Fix zero-length READ and WRITE handling
ibmvscsis: Do not send aborted task response
tcmu: fix module removal due to stuck thread
target: Don't force session reset if queue_depth does not change
iscsi-target: Set session_fall_back_to_erl0 when forcing reinstatement
target: Fix compare_and_write_callback handling for non GOOD status
tcmu: Recalculate the tcmu_cmd size to save cmd area memories
tcmu: Add global data block pool support
tcmu: Add dynamic growing data area feature support
target: fixup error message in target_tg_pt_gp_tg_pt_gp_id_store()
target: fixup error message in target_tg_pt_gp_alua_access_type_store()
target/user: PGR Support
target: Add WRITE_VERIFY_16
Documentation/target: add an example script to configure an iSCSI target
target: Use kmalloc_array() in transport_kmap_data_sg()
target: Use kmalloc_array() in compare_and_write_callback()
target: Improve size determinations in two functions
...
Linus Torvalds [Fri, 12 May 2017 18:39:59 +0000 (11:39 -0700)]
Merge branch 'work.sane_pwd' of git://git./linux/kernel/git/viro/vfs
Pull misc vfs updates from Al Viro:
"Making sure that something like a referral point won't end up as pwd
or root.
The main part is the last commit (fixing mntns_install()); that one
fixes a hard-to-hit race. The fchdir() commit is making fchdir(2) a
bit more robust - it should be impossible to get opened files (even
O_PATH ones) for referral points in the first place, so the existing
checks are OK, but checking the same thing as in chdir(2) is just as
cheap.
The path_init() commit removes a redundant check that shouldn't have
been there in the first place"
* 'work.sane_pwd' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
make sure that mntns_install() doesn't end up with referral for root
path_init(): don't bother with checking MAY_EXEC for LOOKUP_ROOT
make sure that fchdir() won't accept referral points, etc.
Linus Torvalds [Fri, 12 May 2017 17:45:36 +0000 (10:45 -0700)]
Merge branch 'perf-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull perf updates/fixes from Ingo Molnar:
"Mostly tooling updates, but also two kernel fixes: a call chain
handling robustness fix and an x86 PMU driver event definition fix"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/callchain: Force USER_DS when invoking perf_callchain_user()
tools build: Fixup sched_getcpu feature test
perf tests kmod-path: Don't fail if compressed modules aren't supported
perf annotate: Fix AArch64 comment char
perf tools: Fix spelling mistakes
perf/x86: Fix Broadwell-EP DRAM RAPL events
perf config: Refactor a duplicated code for obtaining config file name
perf symbols: Allow user probes on versioned symbols
perf symbols: Accept symbols starting at address 0
tools lib string: Adopt prefixcmp() from perf and subcmd
perf units: Move parse_tag_value() to units.[ch]
perf ui gtk: Move gtk .so name to the only place where it is used
perf tools: Move HAS_BOOL define to where perl headers are used
perf memswap: Split the byteswap memory range wrappers from util.[ch]
perf tools: Move event prototypes from util.h to event.h
perf buildid: Move prototypes from util.h to build-id.h
Linus Torvalds [Fri, 12 May 2017 17:43:25 +0000 (10:43 -0700)]
Merge branch 'timers-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull timer fix from Ingo Molnar:
"A single ARM Juno clocksource driver fix"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
clocksource/arm_arch_timer: Fix arch_timer_mem_find_best_frame()
Linus Torvalds [Fri, 12 May 2017 17:41:45 +0000 (10:41 -0700)]
Merge branch 'core-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull stackprotector fixlet from Ingo Molnar:
"A single fix/enhancement to increase stackprotector canary randomness
on 64-bit kernels with very little cost"
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
stackprotector: Increase the per-task stack canary's random range from 32 bits to 64 bits on 64-bit platforms
Linus Torvalds [Fri, 12 May 2017 17:11:50 +0000 (10:11 -0700)]
Merge branch 'x86-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull x86 fixes from Ingo Molnar:
"Misc fixes:
- two boot crash fixes
- unwinder fixes
- kexec related kernel direct mappings enhancements/fixes
- more Clang support quirks
- minor cleanups
- Documentation fixes"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/intel_rdt: Fix a typo in Documentation
x86/build: Don't add -maccumulate-outgoing-args w/o compiler support
x86/boot/32: Fix UP boot on Quark and possibly other platforms
x86/mm/32: Set the '__vmalloc_start_set' flag in initmem_init()
x86/kexec/64: Use gbpages for identity mappings if available
x86/mm: Add support for gbpages to kernel_ident_mapping_init()
x86/boot: Declare error() as noreturn
x86/mm/kaslr: Use the _ASM_MUL macro for multiplication to work around Clang incompatibility
x86/mm: Fix boot crash caused by incorrect loop count calculation in sync_global_pgds()
x86/asm: Don't use RBP as a temporary register in csum_partial_copy_generic()
x86/microcode/AMD: Remove redundant NULL check on mc
Linus Torvalds [Fri, 12 May 2017 17:09:14 +0000 (10:09 -0700)]
Merge tag 'for-linus-4.12b-rc0c-tag' of git://git./linux/kernel/git/xen/tip
Pull xen fixes from Juergen Gross:
"This contains two fixes for booting under Xen introduced during this
merge window and two fixes for older problems, where one is just much
more probable due to another merge window change"
* tag 'for-linus-4.12b-rc0c-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen: adjust early dom0 p2m handling to xen hypervisor behavior
x86/amd: don't set X86_BUG_SYSRET_SS_ATTRS when running under Xen
xen/x86: Do not call xen_init_time_ops() until shared_info is initialized
x86/xen: fix xsave capability setting
Linus Torvalds [Fri, 12 May 2017 17:04:09 +0000 (10:04 -0700)]
Merge tag 'powerpc-4.12-2' of git://git./linux/kernel/git/powerpc/linux
Pull more powerpc updates from Michael Ellerman:
"The change to the Linux page table geometry was delayed for more
testing with 16G pages, and there's the new CPU features stuff which
just needed one more polish before going in. Plus a few changes from
Scott which came in a bit late. And then various fixes, mostly minor.
Summary highlights:
- rework the Linux page table geometry to lower memory usage on
64-bit Book3S (IBM chips) using the Hash MMU.
- support for a new device tree binding for discovering CPU features
on future firmwares.
- Freescale updates from Scott:
"Includes a fix for a powerpc/next mm regression on 64e, a fix for
a kernel hang on 64e when using a debugger inside a relocated
kernel, a qman fix, and misc qe improvements."
Thanks to: Christophe Leroy, Gavin Shan, Horia Geantă, LiuHailong,
Nicholas Piggin, Roy Pledge, Scott Wood, Valentin Longchamp"
* tag 'powerpc-4.12-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/64s: Support new device tree binding for discovering CPU features
powerpc: Don't print cpu_spec->cpu_name if it's NULL
of/fdt: introduce of_scan_flat_dt_subnodes and of_get_flat_dt_phandle
powerpc/64s: Fix unnecessary machine check handler relocation branch
powerpc/mm/book3s/64: Rework page table geometry for lower memory usage
powerpc: Fix distclean with Makefile.postlink
powerpc/64e: Don't place the stack beyond TASK_SIZE
powerpc/powernv: Block PCI config access on BCM5718 during EEH recovery
powerpc/8xx: Adding support of IRQ in MPC8xx GPIO
soc/fsl/qbman: Disable IRQs for deferred QBMan work
soc/fsl/qe: add EXPORT_SYMBOL for the 2 qe_tdm functions
soc/fsl/qe: only apply QE_General4 workaround on affected SoCs
soc/fsl/qe: round brg_freq to 1kHz granularity
soc/fsl/qe: get rid of immrbar_virt_to_phys()
net: ethernet: ucc_geth: fix MEM_PART_MURAM mode
powerpc/64e: Fix hang when debugging programs with relocated kernel
Linus Torvalds [Fri, 12 May 2017 16:56:30 +0000 (09:56 -0700)]
Merge branch 'upstream' of git://git.linux-mips.org/ralf/upstream-linus
Pull MIPS updates from James Hogan:
"math-emu:
- Add missing clearing of BLTZALL and BGEZALL emulation counters
- Fix BC1EQZ and BC1NEZ condition handling
- Fix BLEZL and BGTZL identification
BPF:
- Add JIT support for SKF_AD_HATYPE
- Use unsigned access for unsigned SKB fields
- Quit clobbering callee saved registers in JIT code
- Fix multiple problems in JIT skb access helpers
Loongson 3:
- Select MIPS_L1_CACHE_SHIFT_6
Octeon:
- Remove vestiges of CONFIG_CAVIUM_OCTEON_2ND_KERNEL
- Remove unused L2C types and macros.
- Remove unused SLI types and macros.
- Fix compile error when USB is not enabled.
- Octeon: Remove unused PCIERCX types and macros.
- Octeon: Clean up platform code.
SNI:
- Remove recursive include of cpu-feature-overrides.h
Sibyte:
- Export symbol periph_rev to sb1250-mac network driver.
- Fix Kconfig warning.
Generic platform:
- Enable Root FS on NFS in generic_defconfig
SMP-MT:
- Use CPU interrupt controller IPI IRQ domain support
UASM:
- Add support for LHU for uasm.
- Remove needless ISA abstraction
mm:
- Add 48-bit VA space and 4-level page tables for 4K pages.
PCI:
- Add controllers before the specified head
irqchip driver for MIPS CPU:
- Replace magic 0x100 with IE_SW0
- Prepare for non-legacy IRQ domains
- Introduce IPI IRQ domain support
MAINTAINERS:
- Update email-id of Rahul Bedarkar
NET:
- sb1250-mac: Add missing MODULE_LICENSE()
CPUFREQ:
- Loongson2: drop set_cpus_allowed_ptr()
Misc:
- Disable Werror when W= is set
- Opt into HAVE_COPY_THREAD_TLS
- Enable GENERIC_CPU_AUTOPROBE
- Use common outgoing-CPU-notification code
- Remove dead define of ST_OFF
- Remove CONFIG_ARCH_HAS_ILOG2_U{32,64}
- Stengthen IPI IRQ domain sanity check
- Remove confusing else statement in __do_page_fault()
- Don't unnecessarily include kmalloc.h into <asm/cache.h>.
- Delete unused definition of SMP_CACHE_SHIFT.
- Delete redundant definition of SMP_CACHE_BYTES"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (39 commits)
MIPS: Sibyte: Fix Kconfig warning.
MIPS: Sibyte: Export symbol periph_rev to sb1250-mac network driver.
NET: sb1250-mac: Add missing MODULE_LICENSE()
MAINTAINERS: Update email-id of Rahul Bedarkar
MIPS: Remove confusing else statement in __do_page_fault()
MIPS: Stengthen IPI IRQ domain sanity check
MIPS: smp-mt: Use CPU interrupt controller IPI IRQ domain support
irqchip: mips-cpu: Introduce IPI IRQ domain support
irqchip: mips-cpu: Prepare for non-legacy IRQ domains
irqchip: mips-cpu: Replace magic 0x100 with IE_SW0
MIPS: Remove CONFIG_ARCH_HAS_ILOG2_U{32,64}
MIPS: generic: Enable Root FS on NFS in generic_defconfig
MIPS: mach-rm: Remove recursive include of cpu-feature-overrides.h
MIPS: Opt into HAVE_COPY_THREAD_TLS
CPUFREQ: Loongson2: drop set_cpus_allowed_ptr()
MIPS: uasm: Remove needless ISA abstraction
MIPS: Remove dead define of ST_OFF
MIPS: Use common outgoing-CPU-notification code
MIPS: math-emu: Fix BC1EQZ and BC1NEZ condition handling
MIPS: r2-on-r6-emu: Clear BLTZALL and BGEZALL debugfs counters
...
Linus Torvalds [Fri, 12 May 2017 16:53:16 +0000 (09:53 -0700)]
Merge tag 'nios2-v4.12-rc1' of git://git./linux/kernel/git/lftan/nios2
Pull nios2 updates from Ley Foon Tan:
"nios2 fixes/enhancements and adding nios2 R2 support"
* tag 'nios2-v4.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/lftan/nios2:
nios2: remove custom early console implementation
nios2: use generic strncpy_from_user() and strnlen_user()
nios2: Add CDX support
nios2: Add BMX support
nios2: Add NIOS2_ARCH_REVISION to select between R1 and R2
nios2: implement flush_dcache_mmap_lock/unlock
nios2: enable earlycon support
nios2: constify irq_domain_ops
nios2: remove wrapper header for cmpxchg.h
nios2: add .gitignore entries for auto-generated files
Takashi Iwai [Thu, 11 May 2017 09:14:45 +0000 (11:14 +0200)]
sound: Disable the build of OSS drivers
OSS drivers are left as badly unmaintained, and now we're facing a
problem to clean up the hackish set_fs() usage in their codes. Since
most of drivers have been covered by ALSA, and the others are dead old
and inactive, let's leave them RIP.
This patch is the first step: disable the build of OSS drivers.
We'll eventually drop the whole codes and clean up later.
Note that sound/oss/dmasound is still kept, since it's a completely
different implementation of OSS, and it doesn't suffer from set_fs()
hack. Moreover, the build of ALSA is disabled on M68K by some reason,
thus disabling it shall result in a regression. This one will be
disabled / removed once when we add the support in ALSA side.
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Ville Syrjälä [Sun, 7 May 2017 17:12:52 +0000 (20:12 +0300)]
drm/i915: Make vblank evade warnings optional
Add a new Kconfig option to enable/disable the extra warnings
from the vblank evade code. For now we'll keep the warning
about an actually missed vblank always enabled as that can have
an actual user visible impact. But if we miss the deadline
othrwise there's no real need to bother the user with that.
We'll want these warnings enabled during development however
so that we can catch regressions.
Based on the reports it looks like this is still very easy
to hit on SKL, so we have more work ahead of us to optimize
the crtiical section further.
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Dave Airlie <airlied@redhat.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reported-by: Jens Axboe <axboe@kernel.dk>
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Fixes: e1edbd44e23b ("drm/i915: Complain if we take too long under vblank evasion.")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Dave Airlie [Fri, 12 May 2017 04:25:22 +0000 (14:25 +1000)]
Merge branch 'linux-4.12' of git://github.com/skeggsb/linux into drm-next
Quite a few patches, but not much code changed:
- Fixes regression from atomic when only the source rect of a plane
changes (ie. xrandr --right-of)
- Fixes another issue where atomic changed behaviour underneath us,
potentially causing laggy cursor position updates
- Fixes for a bunch of races in thermal code, which lead to random
lockups for a lot of users
* 'linux-4.12' of git://github.com/skeggsb/linux:
drm/nouveau/therm: remove ineffective workarounds for alarm bugs
drm/nouveau/tmr: avoid processing completed alarms when adding a new one
drm/nouveau/tmr: fix corruption of the pending list when rescheduling an alarm
drm/nouveau/tmr: handle races with hw when updating the next alarm time
drm/nouveau/tmr: ack interrupt before processing alarms
drm/nouveau/core: fix static checker warning
drm/nouveau/fb/ram/gf100-: remove 0x10f200 read
drm/nouveau/kms/nv50: skip core channel cursor update on position-only changes
drm/nouveau/kms/nv50: fix source-rect-only plane updates
drm/nouveau/kms/nv50: remove pointless argument to window atomic_check_acquire()
Dave Airlie [Fri, 12 May 2017 03:58:29 +0000 (13:58 +1000)]
Merge branch 'drm-next-4.12' of git://people.freedesktop.org/~agd5f/linux into drm-next
Fixes for 4.12. This is a bit bigger than usual since it's 3 weeks
worth of fixes and most of these changes are for vega10 which is
new for 4.12 and still in a fair amount of flux. It looks like
you missed my last pull request, so those patches are included here
as well. Highlights:
- Lots of vega10 fixes
- Fix interruptable wait mixup
- Fan control method fixes
- Misc display fixes for radeon and amdgpu
- Misc bug fixes
* 'drm-next-4.12' of git://people.freedesktop.org/~agd5f/linux: (132 commits)
drm/amd/powerplay: refine pwm1_enable callback functions for CI.
drm/amd/powerplay: refine pwm1_enable callback functions for vi.
drm/amd/powerplay: refine pwm1_enable callback functions for Vega10.
drm/amdgpu: refine amdgpu pwm1_enable sysfs interface.
drm/amdgpu: add amd fan ctrl mode enums.
drm/amd/powerplay: add more smu message on Vega10.
drm/amdgpu: fix dependency issue
drm/amd: fix init order of sched job
drm/amdgpu: add some additional vega10 pci ids
drm/amdgpu/soc15: use atomfirmware for setting bios scratch for reset
drm/amdgpu/atomfirmware: add function to update engine hang status
drm/radeon: only warn once in radeon_ttm_bo_destroy if va list not empty
drm/amdgpu: fix mutex list null pointer reference
drm/amd/powerplay: fix bug sclk/mclk level can't be set on vega10.
drm/amd/powerplay: Setup sw CTF to allow graceful exit when temperature exceeds maximum.
drm/amd/powerplay: delete dead code in powerplay.
drm/amdgpu: Use less generic enum definitions
drm/amdgpu/gfx9: derive tile pipes from golden settings
drm/amdgpu/gfx: drop max_gs_waves_per_vgt
drm/amd/powerplay: disable engine spread spectrum feature on Vega10.
...
Dave Airlie [Fri, 12 May 2017 03:57:20 +0000 (13:57 +1000)]
Merge tag 'drm-misc-next-fixes-2017-05-05' of git://anongit.freedesktop.org/git/drm-misc into drm-next
Core Changes:
- Add quirk for LGD 764 panel to default 10bpc (Mario)
Cc: Mario Kleiner <mario.kleiner.de@gmail.com>
* tag 'drm-misc-next-fixes-2017-05-05' of git://anongit.freedesktop.org/git/drm-misc:
drm/edid: Add 10 bpc quirk for LGD 764 panel in HP zBook 17 G2
Arnd Bergmann [Thu, 11 May 2017 17:14:06 +0000 (10:14 -0700)]
Input: cros_ec_keyb - remove extraneous 'const'
gcc-7 warns about 'const SIMPLE_DEV_PM_OPS', as that macro already contains
a 'const' keyword:
drivers/input/keyboard/cros_ec_keyb.c:663:14: error: duplicate 'const' declaration specifier [-Werror=duplicate-decl-specifier]
static const SIMPLE_DEV_PM_OPS(cros_ec_keyb_pm_ops, NULL, cros_ec_keyb_resume);
This removes the extra one.
Fixes: 6af6dc2d2aa6 ("input: Add ChromeOS EC keyboard driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Ben Skeggs [Thu, 11 May 2017 07:33:39 +0000 (17:33 +1000)]
drm/nouveau/therm: remove ineffective workarounds for alarm bugs
These were ineffective due to touching the list without the alarm lock,
but should no longer be required.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Cc: stable@vger.kernel.org
Ben Skeggs [Thu, 11 May 2017 07:13:29 +0000 (17:13 +1000)]
drm/nouveau/tmr: avoid processing completed alarms when adding a new one
The idea here was to avoid having to "manually" program the HW if there's
a new earliest alarm. This was lazy and bad, as it leads to loads of fun
races between inter-related callers (ie. therm).
Turns out, it's not so difficult after all. Go figure ;)
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Cc: stable@vger.kernel.org
Ben Skeggs [Thu, 11 May 2017 07:03:05 +0000 (17:03 +1000)]
drm/nouveau/tmr: fix corruption of the pending list when rescheduling an alarm
At least therm/fantog "attempts" to work around this issue, which could
lead to corruption of the pending alarm list.
Fix it properly by not updating the timestamp without the lock held, or
trying to add an already pending alarm to the pending alarm list....
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Cc: stable@vger.kernel.org
Ben Skeggs [Thu, 11 May 2017 07:19:48 +0000 (17:19 +1000)]
drm/nouveau/tmr: handle races with hw when updating the next alarm time
If the time to the next alarm is short enough, we could race with HW and
end up with an ~4 second delay until it triggers.
Fix this by checking again after we update HW.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Cc: stable@vger.kernel.org
Ben Skeggs [Thu, 11 May 2017 06:53:42 +0000 (16:53 +1000)]
drm/nouveau/tmr: ack interrupt before processing alarms
Fixes a race where we can miss an alarm that triggers while we're already
processing previous alarms.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Cc: stable@vger.kernel.org
Ben Skeggs [Thu, 4 May 2017 07:29:03 +0000 (17:29 +1000)]
drm/nouveau/core: fix static checker warning
object->engine cannot be NULL, it's either valid, or an error pointer.
This particular condition shouldn't actually be possible, but just in
case, we'll keep it.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Ben Skeggs [Tue, 28 Mar 2017 01:46:37 +0000 (11:46 +1000)]
drm/nouveau/fb/ram/gf100-: remove 0x10f200 read
This reg has moved on Pascal, and causes a bus fault.
We never use the value anyway, so just remove the read.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Ben Skeggs [Mon, 1 May 2017 06:53:40 +0000 (16:53 +1000)]
drm/nouveau/kms/nv50: skip core channel cursor update on position-only changes
The DRM core used to only call prepare_fb/cleanup_fb() when a plane's
framebuffer changed, which achieved the desired effect.
It's apparently now up to the driver to decide on its own.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Cc: stable@vger.kernel.org [4.11+]
Ben Skeggs [Mon, 1 May 2017 06:52:03 +0000 (16:52 +1000)]
drm/nouveau/kms/nv50: fix source-rect-only plane updates
This "optimisation" (which was originally meant to skip updating cursor
settings in the core channel on position-only updates) turned out to be
pointless in the final design of the code before it was merged.
Remove it completely, as it breaks other cases.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Cc: stable@vger.kernel.org [4.10+]