Mauro Carvalho Chehab [Sat, 28 Dec 2013 10:42:47 +0000 (07:42 -0300)]
upstream: [media] em28xx: use a better value for I2C timeouts
In the lack of a better spec, let's assume the timeout
values compatible with SMBus spec:
http://smbus.org/specs/smbus110.pdf
at chapter 8 - Electrical Characteristics of SMBus devices
Ok, SMBus is a subset of I2C, and not all devices will be
following it, but the timeout value before this patch was not
even following the spec.
So, while we don't have a better guess for it, use 35 + 1
ms as the timeout.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Valentine Barshak [Thu, 26 Dec 2013 15:31:49 +0000 (12:31 -0300)]
upstream: [media] media: soc_camera: rcar_vin: Add preliminary R-Car M2 support
This adds R-Car M2 (R8A7791) VIN support. Both H2 and M2
variants look the same from the driver's point of view,
so use GEN2 id for both.
Signed-off-by: Valentine Barshak <valentine.barshak@cogentembedded.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
[g.liakhovetski@gmx.de: removed changelog from commit message]
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Ricardo Ribalda [Tue, 26 Nov 2013 08:31:42 +0000 (05:31 -0300)]
upstream: [media] videodev2: Set vb2_rect's width and height as unsigned
As discussed on the media summit 2013, there is no reason for the width
and height to be signed.
Therefore this patch is an attempt to convert those fields from __s32 to
__u32.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi> (documentation and smiapp)
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Conflicts:
Documentation/DocBook/media/v4l/compat.xml
Documentation/DocBook/media/v4l/v4l2.xml
drivers/media/i2c/soc_camera/mt9m111.c
Hans Verkuil [Thu, 17 Apr 2014 08:00:39 +0000 (05:00 -0300)]
upstream: [media] saa7134: remove fmt from saa7134_buf
This is already available from saa7134_dev.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Hans Verkuil [Thu, 17 Apr 2014 07:55:43 +0000 (04:55 -0300)]
upstream: [media] saa7134: store VBI hlen/vlen globally
Don't calculate this for every buffer, store it globally instead.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Hans Verkuil [Thu, 17 Apr 2014 10:24:31 +0000 (07:24 -0300)]
upstream: [media] saa7134: fix regression with tvtime
This solves this bug:
https://bugzilla.kernel.org/show_bug.cgi?id=73361
The problem is that when you quit tvtime it calls STREAMOFF, but then it queues a
bunch of buffers for no good reason before closing the file descriptor.
In the past closing the fd would free the vb queue since that was part of the file
handle struct. Since that was moved to the global struct that no longer happened.
This wouldn't be a problem, but the extra QBUF calls that tvtime does meant that
the buffer list in videobuf (q->stream) contained buffers, so REQBUFS would fail
with -EBUSY.
The solution is to init the list head explicitly when releasing the file
descriptor and to not free the video resource when calling streamoff.
The real fix will hopefully go into kernel 3.16 when the vb2 conversion is
merged. Basically the saa7134 driver with the old videobuf is so full of holes it
ain't funny anymore, so consider this a band-aid for kernels 3.14 and 15.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: stable@vger.kernel.org # for v3.14 and up
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Hans Verkuil [Sat, 14 Dec 2013 11:28:33 +0000 (08:28 -0300)]
upstream: [media] saa7134: drop log_status for radio
There are no controls for the radio node, so just drop support for this ioctl.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Hans Verkuil [Sat, 14 Dec 2013 11:28:31 +0000 (08:28 -0300)]
upstream: [media] saa6752hs: move to media/i2c
This driver is independent from saa7134, so there is no reason why this
shouldn't be in media/i2c like all other i2c media drivers.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Hans Verkuil [Thu, 17 Apr 2014 08:56:42 +0000 (05:56 -0300)]
upstream: [media] saa7134: rename empress_tsq to empress_vbq
Create consistent _vbq suffix for videobuf_queue fields.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Hans Verkuil [Thu, 17 Apr 2014 07:23:07 +0000 (04:23 -0300)]
upstream: [media] saa7134: swap ts_init_encoder and ts_reset_encoder
This will make the next patch a bit easier to read.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Hans Verkuil [Thu, 17 Apr 2014 06:57:14 +0000 (03:57 -0300)]
upstream: [media] saa7134: drop abuse of low-level videobuf functions
saa7134-alsa used low-level videobuf functions to allocate and sync
DMA buffers. Replace this with saa7134-specific code. These functions
will not be available when we convert to vb2.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Hans Verkuil [Thu, 17 Apr 2014 06:48:50 +0000 (03:48 -0300)]
upstream: [media] saa7134: coding style cleanups
Just white space and coding style changes to reduce the noise in the
following patches.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Hans Verkuil [Sat, 14 Dec 2013 11:28:32 +0000 (08:28 -0300)]
upstream: [media] saa6752hs.h: drop empty header
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Hans Verkuil [Sat, 14 Dec 2013 11:28:28 +0000 (08:28 -0300)]
upstream: [media] saa7134: add support for control events
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Hans Verkuil [Sat, 14 Dec 2013 11:28:27 +0000 (08:28 -0300)]
upstream: [media] saa7134: share resource management between normal and empress nodes
The empress video node can share resource management with the normal
video nodes, thus allowing for code sharing and making the empress node
non-exclusive.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Hans Verkuil [Sat, 14 Dec 2013 11:28:26 +0000 (08:28 -0300)]
upstream: [media] saa7134: remove dev from saa7134_fh, use saa7134_fh for empress node
Use the saa7134_fh struct for the empress video node as well, drop the dev
pointer from that struct since we can use drvdata for that.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Hans Verkuil [Sat, 14 Dec 2013 11:28:25 +0000 (08:28 -0300)]
upstream: [media] saa7134: cleanup radio/video/empress ioctl handling
The video and empress nodes can share various ioctls.
Drop the input/std ioctls from the radio node (out of spec).
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Hans Verkuil [Sat, 14 Dec 2013 11:28:24 +0000 (08:28 -0300)]
upstream: [media] saa7134: convert to the control framework
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Hans Verkuil [Sat, 14 Dec 2013 11:28:23 +0000 (08:28 -0300)]
upstream: [media] saa7134: move the queue data from saa7134_fh to saa7134_dev
These fields are global, not per-filehandle.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Simon Farnsworth [Fri, 20 Sep 2013 16:15:28 +0000 (13:15 -0300)]
upstream: [media] saa7134: Fix crash when device is closed before streamoff
pm_qos_remove_request was not called on video_release, resulting in the PM
core's list of requests being corrupted when the file handle was freed.
This has no immediate symptoms, but later in operation, the kernel will
panic as the PM core dereferences a dangling pointer.
Signed-off-by: Simon Farnsworth <simon.farnsworth@onelan.co.uk>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Hans Verkuil [Mon, 16 Dec 2013 08:45:37 +0000 (05:45 -0300)]
upstream: [media] v4l2: move tracepoints to video_usercopy
The (d)qbuf ioctls were traced in the low-level v4l2 ioctl function. The
trace was outside the serialization lock, so that can affect the usefulness
of the timing. In addition, the __user pointer was expected instead of a
proper kernel pointer.
By moving the tracepoints to video_usercopy we ensure that the trace calls
use the correct kernel pointer, and that it happens right after the ioctl
call to the driver, so certainly inside the serialization lock.
In addition, we only trace if the call was successful.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Wade Farnsworth <wade_farnsworth@mentor.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Antti Palosaari [Thu, 12 Dec 2013 16:34:30 +0000 (13:34 -0300)]
upstream: [media] v4l: add stream format for SDR receiver
Add new V4L2 stream format definition, V4L2_BUF_TYPE_SDR_CAPTURE,
for SDR receiver.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Wade Farnsworth [Fri, 22 Nov 2013 19:48:28 +0000 (16:48 -0300)]
upstream: [media] v4l2-dev: Add tracepoints for QBUF and DQBUF
Add tracepoints to the QBUF and DQBUF ioctls to enable rudimentary
performance measurements using standard kernel tracers.
[m.chehab@samsung.com: CodingStyle fixes (whitespacing)]
Signed-off-by: Wade Farnsworth <wade_farnsworth@mentor.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Martin Bugge [Wed, 19 Mar 2014 09:43:45 +0000 (06:43 -0300)]
upstream: [media] adv7842: Disable access to EDID DDC lines before chip power up
In core_init make sure access to EDID DDC lines are disabled
before chip is powered up. Also DISABLE_AUTO_EDID before power up.
The correct setting is applied later when setting the EDID.
Some sources (MAC) kept on reading EDID even when Hotplug was low
and in the short period in core_init before the DDC lines was enabled
read a corrupt EDID.
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Martin Bugge [Wed, 19 Mar 2014 09:43:43 +0000 (06:43 -0300)]
upstream: [media] adv7842: update RGB quantization range on HDMI/DVI-D mode irq
This was the reason for enabling the HDMI/DVI-D mode irq in the first place.
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Hans Verkuil [Tue, 4 Mar 2014 11:05:19 +0000 (08:05 -0300)]
upstream: [media] adv*: replace the deprecated v4l2_subdev_edid by v4l2_edid
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Martin Bugge [Fri, 24 Jan 2014 13:50:06 +0000 (10:50 -0300)]
upstream: [media] adv7842: platform-data for Hotplug Active (HPA) manual/auto
This applies to HDMI-map register 0x69.
So far we have been using HPA manual mode.
This way we had control of HPA which could be
set after EDID had been programmed.
Using a Mac Mini with mini-displayport to DVI-D converter as source
caused the adv7842 to lock up and fail to detect any further signals.
After experimenting with different configurations it was found that
using the HPA auto mode and in addition letting RX-termination
be controlled by HPA prevented this error from occuring.
I was not able to re-create this problem on the adv7604.
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Cc: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Martin Bugge [Fri, 24 Jan 2014 13:50:05 +0000 (10:50 -0300)]
upstream: [media] adv7842: log-status for Audio Video Info frames (AVI)
Clear any pending AVI checksum-errors.
To be able to display last received AVI.
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Cc: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Martin Bugge [Fri, 24 Jan 2014 13:50:04 +0000 (10:50 -0300)]
upstream: [media] adv7842: pixelclock read-out
Incorrect registers used for pixelclock read-out.
Same registers as for adv7604 which actually gave an almost
correct read-out, even they are not documented for adv7842.
Corrected deep-color pixel-clock correction.
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Cc: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Martin Bugge [Fri, 24 Jan 2014 13:50:03 +0000 (10:50 -0300)]
upstream: [media] adv7842: adjust gain and offset for DVI-D signals
If the input signal is DVI-D and quantization range is RGB full range,
gain and offset must be adjusted to get the right range on the output.
Copied and adopted from adv7604.
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Cc: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Martin Bugge [Wed, 29 Jan 2014 09:50:20 +0000 (06:50 -0300)]
upstream: [media] adv7842: Composite free-run platfrom-data fix
Incorrectly setting of free-run for Composite.
Copy/paste regression fix.
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Hans Verkuil [Fri, 20 Dec 2013 09:15:13 +0000 (06:15 -0300)]
upstream: [media] adv7842: add drive strength enum and sync names with adv7604
Add a proper driver strength enum and use the same names in the platform
data as with adv7604.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Hans Verkuil [Tue, 17 Dec 2013 13:09:51 +0000 (10:09 -0300)]
upstream: [media] adv7842: initialize timings to CEA 640x480p59.94
This timing must be supported by all HDMI equipment, so that's a
reasonable default.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Hans Verkuil [Fri, 20 Dec 2013 09:03:58 +0000 (06:03 -0300)]
upstream: [media] adv7842: set LLC DLL phase from platform_data
The correct LLC DLL phase depends on the board layout, so this
should be part of the platform_data.
Also updated the platform_data in ezkit to ensure that what was the old
default value is now explicitly specified, so the behavior for that board
is unchanged.
Tested-by: Martin Bugge <marbugge@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Martin Bugge [Thu, 12 Dec 2013 13:10:57 +0000 (10:10 -0300)]
upstream: [media] adv7842: return 0 if no change in s_dv_timings
Return 0 if the new timings are equal to the current timings as
it caused extra cp-loss/lock interrupts.
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Martin Bugge [Thu, 5 Dec 2013 15:22:53 +0000 (12:22 -0300)]
upstream: [media] adv7842: Composite sync adjustment
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Martin Bugge [Fri, 20 Dec 2013 09:02:24 +0000 (06:02 -0300)]
upstream: [media] adv7842: obtain free-run mode from the platform_data
The free-run mode can be board-specific.
Also updated the platform_data in ezkit to ensure that what was the old
default value is now explicitly specified, so the behavior for that board
is unchanged.
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Martin Bugge [Thu, 5 Dec 2013 15:18:14 +0000 (12:18 -0300)]
upstream: [media] adv7842: composite sd-ram test, clear timings before setting
Must clear timings before setting after test to recover.
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Martin Bugge [Tue, 10 Dec 2013 15:01:59 +0000 (12:01 -0300)]
upstream: [media] adv7842: enable HDMI/DVI mode irq
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Martin Bugge [Thu, 5 Dec 2013 15:14:45 +0000 (12:14 -0300)]
upstream: [media] adv7842: i2c dummy clients registration
Clear i2c_clients ptr when unregistered.
Warn if configured i2c-addr is zero.
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Martin Bugge [Thu, 5 Dec 2013 15:14:02 +0000 (12:14 -0300)]
upstream: [media] adv7842: support g_edid ioctl
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Martin Bugge [Tue, 10 Dec 2013 15:00:06 +0000 (12:00 -0300)]
upstream: [media] adv7842: restart STDI once if format is not found
The STDI block may measure wrong values, especially for lcvs and lcf.
If the driver can not find any valid timing, the STDI block is restarted
to measure the video timings again. The function will return an error,
but the restart of STDI will generate a new STDI interrupt and the format
detection process will restart.
Copied from adv7604.
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Cc: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Martin Bugge [Thu, 5 Dec 2013 15:09:51 +0000 (12:09 -0300)]
upstream: [media] adv7842: clear edid, if no edid just disable Edid-DDC access
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Cc: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Mats Randgaard [Thu, 5 Dec 2013 15:08:45 +0000 (12:08 -0300)]
upstream: [media] adv7842: mute audio before switching inputs to avoid noise/pops
Signed-off-by: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Mats Randgaard [Tue, 10 Dec 2013 14:24:35 +0000 (11:24 -0300)]
upstream: [media] adv7842: Use defines to select EDID port
Signed-off-by: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Mats Randgaard [Thu, 5 Dec 2013 14:58:08 +0000 (11:58 -0300)]
upstream: [media] adv7842: remove connector type. Never used for anything useful
May also be wrong if the receiver is connected to more than one connector.
Signed-off-by: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Martin Bugge [Thu, 5 Dec 2013 14:56:32 +0000 (11:56 -0300)]
upstream: [media] adv7842: increase wait time
Wait 5ms after main reset. The data-sheet doesn't specify the wait
after i2c-controlled reset, so using same value as after pin-controlled
reset.
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Martin Bugge [Thu, 5 Dec 2013 14:55:48 +0000 (11:55 -0300)]
upstream: [media] adv7842: set default input in platform-data
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Martin Bugge [Thu, 5 Dec 2013 14:52:39 +0000 (11:52 -0300)]
upstream: [media] adv7842: 625/525 line standard jitter fix
Both the PAL and NTSC standards are interlaced where a
frame consist of two fields. Total number of lines in a frame in both systems
are an odd number so the two fields will have different length.
In the 625 line standard ("PAL") the odd field of the frame is transmitted first,
while in the 525 standard ("NTSC") the even field is transmitted first.
This adds the possibility to change output config between the fields and standards.
This setting will reduce the "format-jitter" on the signal sent by the pixelport
moving the difference between the fields to vertical front/back-porch only.
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Martin Bugge [Thu, 5 Dec 2013 14:46:21 +0000 (11:46 -0300)]
upstream: [media] adv7842: set defaults spa-location
For edid with no Source Physical Address (spa), set
spa-location to default and use correct values from edid.
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Cc: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Hans Verkuil [Fri, 20 Dec 2013 08:44:27 +0000 (05:44 -0300)]
upstream: [media] adv7842: support YCrCb analog input, receive CEA formats as RGB on VGA input
Added support for YCrCb analog input.
If input is ADV7842_MODE_RGB and RGB quantization range is set to
V4L2_DV_RGB_RANGE_AUTO, then video with CEA timings will be received
as RGB. For ADV7842_MODE_COMP, automatic CSC mode will be selected.
See table 48 on page 281 in "ADV7842 Hardware Manual, Rev. 0, January 2011"
for details.
Make sure that when switching inputs the RGB quantization range is
updated as well.
Also updated the platform_data in ezkit to ensure that what was the old
default value is now explicitly specified, so the behavior for that board
is unchanged.
Signed-off-by: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Martin Bugge [Thu, 5 Dec 2013 14:40:43 +0000 (11:40 -0300)]
upstream: [media] adv7842: added DE vertical position in SDP-io-sync
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Martin Bugge [Thu, 5 Dec 2013 14:39:37 +0000 (11:39 -0300)]
upstream: [media] adv7842: save platform data in state struct
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Martin Bugge [Tue, 10 Dec 2013 14:14:26 +0000 (11:14 -0300)]
upstream: [media] adv7842: properly enable/disable the irqs
The method of disabling the irq-output pin caused many "empty"
interrupts. Instead, actually disable/enable the interrupts by
changing the interrupt masks.
Also enable STORE_MASKED_IRQ in INT1 configuration, otherwise when HDMI
events happen while the interrupt is masked those events will be ignored
when the interrupt is unmasked.
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Martin Bugge [Tue, 10 Dec 2013 14:01:00 +0000 (11:01 -0300)]
upstream: [media] adv7842: corrected setting of cp-register 0x91 and 0x8f
Bit 6 of register 0x8f was cleared incorrectly (must be 1), and bit 4
of register 0x91 was set incorrectly (must be 0).
These bits are undocumented, so we shouldn't modify them to values different
from what the datasheet specifies.
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Martin Bugge [Tue, 10 Dec 2013 13:57:03 +0000 (10:57 -0300)]
upstream: [media] adv7842: Re-worked query_dv_timings()
This simplified the code quite a bit.
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Gianluca Gennari [Fri, 30 Aug 2013 11:29:22 +0000 (08:29 -0300)]
upstream: [media] adv7842: fix compilation with GCC < 4.4.6
Signed-off-by: Gianluca Gennari <gennarone@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Hans Verkuil [Thu, 22 Aug 2013 09:14:22 +0000 (06:14 -0300)]
upstream: [media] adv7842: add new video decoder driver
This is a Analog Devices Component/Graphics/SD Digitizer with 2:1
Multiplexed HDMI Receiver.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Hans Verkuil [Tue, 17 Dec 2013 13:05:13 +0000 (10:05 -0300)]
upstream: [media] adv7604: initialize timings to CEA 640x480p59.94
This timing must be supported by all HDMI equipment, so that's a
reasonable default.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Martin Bugge [Fri, 20 Dec 2013 08:14:57 +0000 (05:14 -0300)]
upstream: [media] adv7604: sync polarities from platform data
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Mats Randgaard [Tue, 10 Dec 2013 13:15:13 +0000 (10:15 -0300)]
upstream: [media] adv7604: Enable HDMI_MODE interrupt
Some sources are initially detected as DVI, and change to HDMI later.
This must be detected to set the right RGB quantization range.
Signed-off-by: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Mats Randgaard [Thu, 5 Dec 2013 13:39:04 +0000 (10:39 -0300)]
upstream: [media] adv7604: adjust gain and offset for DVI-D signals
If the input signal is DVI-D and quantization range is RGB full range,
gain and offset must be adjusted to get the right range on the output.
Signed-off-by: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Mats Randgaard [Thu, 5 Dec 2013 13:33:41 +0000 (10:33 -0300)]
upstream: [media] adv7604: improve HDMI audio handling
- Mute audio before switching inputs to avoid noise/pops
- Mute audio if audio FIFO over-/underflows (AD Recommended setting)
- Reset FIFO if it over-/underflows (AD Recommended setting)
Signed-off-by: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Mats Randgaard [Thu, 5 Dec 2013 13:26:11 +0000 (10:26 -0300)]
upstream: [media] adv7604: remove debouncing of ADV7604_FMT_CHANGE events
ADV7604_FMT_CHANGE events was debounced in adv7604_isr() to avoid
that a receiver with a unstable input signal would block the event
handling for other inputs. This solution was prone to errors.
A better protection agains interrupt blocking is to delay the call
of the interrupt service routine in the adv7604 driver if too many
interrupts are received within a given time.
Signed-off-by: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Mats Randgaard [Thu, 5 Dec 2013 13:24:05 +0000 (10:24 -0300)]
upstream: [media] adv7604: return immediately if the new input is equal to what is configured
Signed-off-by: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Mats Randgaard [Thu, 5 Dec 2013 13:23:03 +0000 (10:23 -0300)]
upstream: [media] adv7604: remove connector type. Never used for anything useful
May also be wrong if the receiver is connected to more than one connector.
Signed-off-by: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Mats Randgaard [Tue, 10 Dec 2013 12:57:09 +0000 (09:57 -0300)]
upstream: [media] adv7604: improve EDID handling
- split edid_write_block()
- do not use edid->edid before the validity check
- Return -EINVAL if edid->pad is invalid
- Save both registers for SPA port A
- Set SPA location to default value if it is not found
Signed-off-by: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Mats Randgaard [Tue, 10 Dec 2013 12:55:18 +0000 (09:55 -0300)]
upstream: [media] adv7604: set CEC address (SPA) in EDID
Signed-off-by: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Mats Randgaard [Thu, 5 Dec 2013 13:17:15 +0000 (10:17 -0300)]
upstream: [media] adv7604: select YPbPr if RGB_RANGE_FULL/LIMITED is set for VGA_COMP inputs
Signed-off-by: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Mats Randgaard [Thu, 5 Dec 2013 13:05:58 +0000 (10:05 -0300)]
upstream: [media] adv7604: Receive CEA formats as RGB on VGA (RGB) input
If the input is ADV7604_INPUT_VGA_RGB and RGB quantization range is
set to V4L2_DV_RGB_RANGE_AUTO, video with CEA timings will be
received as RGB. For ADV7604_INPUT_VGA_COMP, automatic CSC mode
will be selected.
See table 44 on page 205 in "ADV7604 Hardware Manual, Rev. F, August 2010"
for details.
Signed-off-by: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Mikhail Khelik [Fri, 20 Dec 2013 08:12:00 +0000 (05:12 -0300)]
upstream: [media] adv7604: add hdmi driver strength adjustment
The driver strength is board dependent, so set it from the platform_data.
Signed-off-by: Mikhail Khelik <mkhelik@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Mats Randgaard [Tue, 10 Dec 2013 12:45:00 +0000 (09:45 -0300)]
upstream: [media] adv7604: add support for all the digital input ports
The adv7604 supports four digital input ports. This patch adds support
for all of them, instead of just port A.
Signed-off-by: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Hans Verkuil [Mon, 19 Aug 2013 11:07:26 +0000 (08:07 -0300)]
upstream: [media] adv7604/ad9389b/ths8200: decrease min_pixelclock to 25MHz
The CEA-861 standard allows for the 640x480 format at 25.175 MHz.
Ensure that that's allowed according to the struct v4l2_bt_timings_cap.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Hans Verkuil [Thu, 15 Aug 2013 11:05:59 +0000 (08:05 -0300)]
upstream: [media] ad9389b/adv7604/ths8200: use new v4l2_print_dv_timings helper
These three drivers all have code to log the dv_timings contents. Replace
that code with the new helper function.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Mats Randgaard [Wed, 14 Aug 2013 10:58:45 +0000 (07:58 -0300)]
upstream: [media] adv7604: debounce "format change" notifications
The bridge driver is only notified when the input status has changed
since the previous interrupt.
Signed-off-by: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Hans Verkuil [Thu, 12 Dec 2013 10:35:22 +0000 (07:35 -0300)]
upstream: [media] sn9c102: prepare for removal by moving it to staging
During the last media summit meeting it was decided to move this driver to
staging as the first step to removing it altogether.
Most webcams covered by this driver are now supported by gspca. Nobody has the
hardware to convert the remaining devices to gspca.
This driver needs a major overhaul to have it conform to the latest frameworks
and compliancy tests.
Without hardware, however, this is next to impossible. Given the fact that
this driver seems to be pretty much unused (it has been removed from Fedora
several versions ago and nobody complained about that), we decided to drop
this driver.
This patch moves it to staging. Some time in 2014 we will drop it completely.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Luca Risolia <luca.risolia@studio.unibo.it>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Conflicts:
drivers/staging/media/Kconfig
Masanari Iida [Sun, 8 Dec 2013 15:22:53 +0000 (00:22 +0900)]
upstream: treewide: Fix typos in printk
Correct spelling typo in various part of kernel
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Conflicts:
arch/arm64/kvm/handle_exit.c
arch/mips/ralink/cevt-rt3352.c
arch/mips/ralink/timer.c
drivers/gpu/drm/exynos/exynos_drm_fimc.c
drivers/i2c/busses/i2c-exynos5.c
drivers/iio/adc/twl6030-gpadc.c
fs/btrfs/tests/free-space-tests.c
net/nfc/digital_dep.c
Mauro Carvalho Chehab [Fri, 16 May 2014 13:55:55 +0000 (10:55 -0300)]
upstream: [media] m88ts2022: convert to Kernel I2C driver model
Convert driver from proprietary DVB driver model to standard I2C
driver model.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Conflicts:
drivers/media/tuners/m88ts2022.c
Conflicts:
drivers/media/tuners/m88ts2022.c
Antti Palosaari [Thu, 7 Nov 2013 20:01:31 +0000 (17:01 -0300)]
upstream: [media] m88ts2022: do not use dynamic stack allocation
I2C transfer were using dynamic stack allocation. Get rid of it.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Antti Palosaari [Mon, 25 Feb 2013 12:01:13 +0000 (09:01 -0300)]
upstream: [media] em28xx: add support for PCTV DVB-S2 Stick (461e) [2013:0258]
Device has following chips: Empia EM28178, Montage M88DS3103,
Montage M88TS2022, Allegro A8293.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Hans Verkuil [Fri, 13 Dec 2013 11:06:38 +0000 (08:06 -0300)]
upstream: [media] si470x: add check to test if this is really a si470x
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Hans Verkuil [Fri, 13 Dec 2013 11:06:07 +0000 (08:06 -0300)]
upstream: [media] si470x: don't use buffer on the stack for USB transfers
You shouldn't use buffers allocated on the stack for USB transfers,
always kmalloc them.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Sakari Ailus [Fri, 13 Dec 2013 11:58:37 +0000 (08:58 -0300)]
upstream: [media] media: Include linux/kernel.h for DIV_ROUND_UP()
DIV_ROUND_UP() is defined in kernel.h which was not included by
media-entity.h. Do exactly that.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Conflicts:
include/media/media-entity.h
Paul Gortmaker [Tue, 10 Dec 2013 20:23:48 +0000 (15:23 -0500)]
upstream: staging: delete non-required instances of include <linux/init.h>
None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>. Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Conflicts:
drivers/staging/comedi/drivers/dt9812.c
drivers/staging/ft1000/ft1000-usb/ft1000_hw.c
drivers/staging/gdm724x/gdm_tty.c
drivers/staging/lustre/include/linux/libcfs/linux/kp30.h
drivers/staging/lustre/include/linux/libcfs/linux/linux-prim.h
drivers/staging/lustre/lnet/klnds/o2iblnd/o2iblnd.h
drivers/staging/lustre/lnet/klnds/socklnd/socklnd_lib-linux.h
drivers/staging/lustre/lustre/lmv/lmv_fld.c
drivers/staging/lustre/lustre/lmv/lmv_intent.c
drivers/staging/lustre/lustre/lvfs/lvfs_linux.c
drivers/staging/lustre/lustre/mdc/mdc_locks.c
drivers/staging/lustre/lustre/obdclass/capa.c
drivers/staging/lustre/lustre/obdclass/linux/linux-module.c
drivers/staging/lustre/lustre/ptlrpc/gss/gss_bulk.c
drivers/staging/lustre/lustre/ptlrpc/gss/gss_generic_token.c
drivers/staging/lustre/lustre/ptlrpc/gss/gss_mech_switch.c
drivers/staging/lustre/lustre/ptlrpc/gss/lproc_gss.c
drivers/staging/ozwpan/ozpd.c
drivers/staging/ozwpan/ozproto.c
drivers/staging/ozwpan/ozusbsvc.c
drivers/staging/rtl8188eu/include/osdep_service.h
drivers/staging/rtl8192u/r8192U.h
drivers/staging/rts5208/rtsx.h
drivers/staging/zsmalloc/zsmalloc-main.c
Frank Schaefer [Sun, 1 Dec 2013 21:06:57 +0000 (18:06 -0300)]
upstream: [media] em28xx: add support for the SpeedLink Vicious And Devine Laplace webcams
The SpeedLink Vicious And Devine Laplace webcam is using an EM2765 bridge and
an OV2640 sensor. It has a built-in microphone (USB standard device class)
and provides 3 buttons (snapshot, illumination, mute) and 2 LEDs (capturing/mute
and illumination/flash). It is also equipped with an eeprom.
The device is available in two colors: white (1ae7:9003) and black (1ae7:9004).
For further details see http://linuxtv.org/wiki/index.php/VAD_Laplace.
Please note the following limitations that need to be addressed later:
- resolution limited to 640x480 (sensor supports 1600x1200)
- picture quality needs to be improved
- AV-mute button doesn't work yet
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Jean-Francois Thibert [Wed, 9 Oct 2013 14:18:05 +0000 (11:18 -0300)]
upstream: [media] Add support for KWorld UB435-Q V2
This patch adds support for the UB435-Q V2. You might need to
use the device once with the Windows driver provided by KWorld
in order to permanently reprogram the device descriptors. Thanks
to Jarod Wilson for the initial attempt at adding support for this
device.
[m.chehab@samsung.com: Fixed Whitespace mangling, Coding Style and
improved the error handling at DVB attach]
Signed-off-by: Jean-Francois Thibert <jfthibert@google.com>
Reviewed-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Evgeny Plehov [Fri, 15 Nov 2013 19:43:33 +0000 (16:43 -0300)]
upstream: [media] dw2102: Use RC Core instead of the legacy RC (second edition)
Use RC Core instead of the legacy RC.
DVBWorld, TBS, TeVii, Prof hardware decode only NEC remotes (one byte code).
Geniatech hardware decode only RC5 (two bytes).
+ New keymap for Geniatech HDStar (SU3000).
Signed-off-by: Evgeny Plehov <EvgenyPlehov@ukr.net>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Evgeny Plehov [Wed, 13 Nov 2013 23:53:59 +0000 (20:53 -0300)]
upstream: [media] dw2102: Geniatech T220 support
Support for Geniatech T220 DVB-T/T2/C USB stick.
Signed-off-by: Evgeny Plehov <EvgenyPlehov@ukr.net>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Jonathan McCrohan [Mon, 21 Oct 2013 00:34:01 +0000 (21:34 -0300)]
upstream: [media] media_tree: Fix spelling errors
Fix various spelling errors in strings and comments throughout the media
tree. The majority of these were found using Lucas De Marchi's codespell
tool.
[m.chehab@samsung.com: discard hunks with conflicts]
Signed-off-by: Jonathan McCrohan <jmccrohan@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Conflicts:
drivers/media/dvb-frontends/drxk_hard.c
drivers/media/i2c/adv7842.c
drivers/media/i2c/s5c73m3/s5c73m3-core.c
Ricardo Ribalda [Tue, 26 Nov 2013 12:58:44 +0000 (09:58 -0300)]
upstream: [media] videobuf2-dma-sg: Support io userptr operations on io memory
Memory exported via remap_pfn_range cannot be remapped via
get_user_pages.
Other videobuf2 methods (like the dma-contig) supports io memory.
This patch adds support for this kind of memory.
v2: Comments by Marek Szyprowski
-Use vb2_get_vma and vb2_put_vma
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Conflicts:
drivers/media/v4l2-core/videobuf2-dma-sg.c
Georg Kaindl [Mon, 21 Oct 2013 15:01:36 +0000 (12:01 -0300)]
upstream: [media] usbtv: Add support for PAL video source
Signed-off-by: Georg Kaindl <gkaindl@mac.com>
Tested-by: Lubomir Rintel <lkundrak@v3.sk>
Tested-by: Marcin Nowak <marcin.nowak@simplusnet.pl>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Antti Palosaari [Thu, 8 Aug 2013 22:41:06 +0000 (19:41 -0300)]
upstream: [media] af9035: add [0413:6a05] Leadtek WinFast DTV Dongle Dual
It is IT9135 dual design.
Thanks to Michael Piko for reporting that!
Reported-by: Michael Piko <michael@piko.com.au>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Conflicts:
drivers/media/usb/dvb-usb-v2/af9035.c
Antti Palosaari [Wed, 30 Oct 2013 05:33:42 +0000 (02:33 -0300)]
upstream: [media] rtl28xxu: add 15f4:0131 Astrometa DVB-T2
Components are RTL2832P + R828D + MN88472.
Currently support only DVB-T as there is no driver for MN88472 demod.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Valentine Barshak [Fri, 4 Oct 2013 14:20:52 +0000 (11:20 -0300)]
upstream: [media] media: rcar_vin: Add preliminary r8a7790 support
Signed-off-by: Valentine Barshak <valentine.barshak@cogentembedded.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Vladimir Barinov [Thu, 25 Jul 2013 20:23:10 +0000 (17:23 -0300)]
upstream: [media] V4L2: soc_camera: Renesas R-Car VIN driver
Add Renesas R-Car VIN (Video In) V4L2 driver.
Based on the patch by Phil Edworthy <phil.edworthy@renesas.com>.
[Sergei: removed deprecated IRQF_DISABLED flag, reordered/renamed 'enum chip_id'
values, reordered rcar_vin_id_table[] entries, removed senseless parens from
to_buf_list() macro, used ALIGN() macro in rcar_vin_setup(), added {} to the
*if* statement and used 'bool' values instead of 0/1 where necessary, removed
unused macros, done some reformatting and clarified some comments.]
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Hans Verkuil [Fri, 4 Oct 2013 14:01:45 +0000 (11:01 -0300)]
upstream: [media] drxk_hard: fix sparse warnings
drivers/media/dvb-frontends/drxk_hard.c:1086:62: warning: Using plain integer as NULL pointer
drivers/media/dvb-frontends/drxk_hard.c:2784:63: warning: Using plain integer as NULL pointer
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Reviewed-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Masanari Iida [Sun, 29 Sep 2013 11:54:15 +0000 (20:54 +0900)]
upstream: treewide: Fix typo in Kconfig
Correct spelling typo in Kconfig.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Conflicts:
arch/arm/mach-sti/Kconfig
drivers/fmc/Kconfig
Ondrej Zary [Fri, 30 Aug 2013 20:54:24 +0000 (17:54 -0300)]
upstream: [media] gspca: Support variable resolution
Add variable resolution support to gspca by allowing subdrivers to
specify try_fmt and enum_framesizes functions.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Conflicts:
drivers/media/usb/gspca/gspca.c
Marek Szyprowski [Wed, 19 Jun 2013 11:56:46 +0000 (08:56 -0300)]
upstream: [media] videobuf2-dc: Fix support for mappings without struct page in userptr mode
Earlier version of dma-contig allocator in user ptr mode assumed that in
all cases DMA address equals physical address. This was just a special case.
Commit
e15dab752d4c588544ccabdbe020a7cc092e23c8 introduced correct support
for converting userpage to dma address, but unfortunately it broke the
support for simple dma address = physical address for the case, when given
physical frame has no struct page associated with it (this happens if one
use for example dma_declare_coherent api or other reserved memory approach).
This commit restores support for such cases.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
[s.nawrocki@samsung.com: replaced #elsif with #elif]
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Conflicts:
drivers/media/v4l2-core/videobuf2-dma-contig.c
Hans Verkuil [Mon, 19 Aug 2013 11:38:29 +0000 (08:38 -0300)]
upstream: [media] v4l2-dv-timings: fill in type field
The detect_cvt/gtf functions didn't fill in the type field.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
projects / platform / kernel / linux-3.10.git / log