[SCSI] qla2xxx: Reference proper ha during SBR handling.

The executing-HA of an SRB can be referenced from the sp->fcport.
Use this correct value while processing status-continuation data
and abort processing.

Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] qla2xxx: Set npiv_supported flag for FCoE HBAs.

Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] qla2xxx: Don't leak SG-DMA mappings while aborting commands.

Original code inadvertently cleared an SRB's 'flags' while
aborting; causing a follow-on scsi_dma_unmap() to be potentially
missed.

Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] qla2xxx: Correct vport-state management issues during ISP-ABORT.

* Use correct 'ha' to mark a device lost from ISR.
  I/Os will always be returned on the physical-HA.
  qla2x00_mark_device_lost() should be called with the HA bound
  to the fcport.
* Mark *all* devices lost during ISP-ABORT (bighammer).

These fixes correct issues discovered locally where during
link-perturbation and heavy vport-I/O fcport/rport states would
stray and an rport's scsi-target lost (timed-out).

Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] qla2xxx: Correct synchronization of software/firmware fcport states.

Greg Wettstein (greg@enjellic.com) noted:

http://article.gmane.org/gmane.linux.scsi/43409

on a reboot of a previously recognized SCST target, the initiator
driver would be unable to re-recognize the device as a target.
It turns out that prior to the SCST software reloading and
returning it's "target-capable" abilities in the PRLI payload,
the HBA would be re-initialized as an initiator-only type port.
Since initiators typically classify themselves as an FCP-2
capable device, both software and firmware do not perform an
explicit logout during port-loss.  Unfortunately, as can be seen
by the failure case, when the port (now target-capable) returns,
firmware performs an ADISC without a follow-on PRLI, leaving
stale 'initiator-only' data in the firmware's port database.

Correct the discrepancy by performing the explicit logout during
the transport's request to terminate-rport-io, thus synchronizing
port states and ensuring a follow-on PRLI is performed.

Reported-by: Greg Wettstein <greg@enjellic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Cc: Stable Tree <stable@kernel.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] scsi_dh: Initialize lun_state in check_ownership()

lun_state need to be initialized inside check_ownership().

Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] scsi_dh: Do not use scsilun in rdac hardware handler

RDAC storage controller doesn't seem to use the scsilun format. It uses
only the last byte for LUN.

Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] megaraid_sas: version and Documentation Update

Signed-off-by: Bo Yang <bo.yang@lsi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] megaraid_sas: add new controllers (0x78 0x79)

Add the new controllers (0x78 0x79) support to the driver.  Those
controllers are LSI's next generation (gen2) SAS controllers.

[akpm@linux-foundation.org: coding-style fixes]
[akpm@linux-foundation.org: parenthesise a macro]
Signed-off-by: Bo Yang <bo.yang@lsi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] megaraid_sas: add the shutdown DCMD cmd to driver shutdown routine

Add the shutdown DCMD cmd to driver shutdown routine to make megaraid sas
FW shutdown proper.

Signed-off-by: Bo Yang <bo.yang@lsi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] megaraid_sas: add readl to force PCI posting flush

MegaRAID SAS Driver get unexpected Interrupt.  Add the dummy readl to
force PCI flush will fix this issue.

Signed-off-by: Bo Yang <bo.yang@lsi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Stable Tree <stable@kernel.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] sd: fix USB devices incorrectly reporting DIF support

Some USB devices set the protect bit in the INQUIRY data which
currently causes the DIF code in sd to assume (incorrectly) that they
support READ_CAPACITY(16).  Fix this (only for the time being) by
making sure we only believe the protect bit in the inquiry data if the
device claims conformance to SCSI-3 or above.

Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

Linux 2.6.27-rc2

Re-introduce "[SCSI] extend the last_sector_bug flag to cover more sectors"

This re-introduces commit 2b142900784c6e38c8d39fa57d5f95ef08e735d8,
which was reverted due to the regression it caused by commit
fca082c9f1e11ec07efa8d2f9f13688521253f36.

That regression was not root-caused by the original commit, it was just
uncovered by it, and the real fix was done by Alan Stern in commit
580da34847488b404218d1d7f53b156f245f5555 ("Fix USB storage hang on
command abort").

We can thus re-introduce the change that was confirmed by Alan Jenkins
to be still required by his odd card reader.

Cc: Alan Jenkins <alan-jenkins@tuffmail.co.uk>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Merge git://git./linux/kernel/git/davem/net-2.6

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (78 commits)
  AX.25: Fix sysctl registration if !CONFIG_AX25_DAMA_SLAVE
  pktgen: mac count
  pktgen: random flow
  bridge: Eliminate unnecessary forward delay
  bridge: fix compile warning in net/bridge/br_netfilter.c
  ipv4: remove unused field in struct flowi (include/net/flow.h).
  tg3: Fix 'scheduling while atomic' errors
  net: Kill plain NET_XMIT_BYPASS.
  net_sched: Add qdisc __NET_XMIT_BYPASS flag
  net_sched: Add qdisc __NET_XMIT_STOLEN flag
  iwl3945: fix merge mistake for packet injection
  iwlwifi: grap nic access before accessing periphery registers
  iwlwifi: decrement rx skb counter in scan abort handler
  iwlwifi: fix unhandled interrupt when HW rfkill is on
  iwlwifi: implement iwl5000_calc_rssi
  iwlwifi: memory allocation optimization
  iwlwifi: HW bug fixes
  p54: Fix potential concurrent access to private data
  rt2x00: Disable link tuning in rt2500usb
  iwlwifi: Don't use buffer allocated on the stack for led names
  ...

AX.25: Fix sysctl registration if !CONFIG_AX25_DAMA_SLAVE

Since 49ffcf8f99e8d33ec8afb450956804af518fd788 ("sysctl: update
sysctl_check_table") setting struct ctl_table.procname = NULL does no
longer work as it used to the way the AX.25 code is expecting it to
resulting in the AX.25 sysctl registration code to break if
CONFIG_AX25_DAMA_SLAVE was not set as in some distribution kernels.
Kernel releases from 2.6.24 are affected.

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

pktgen: mac count

dst_mac_count and src_mac_count patch from Eneas Hunguana
We have sent one mac address to much.

Signed-off-by: Robert Olsson <robert.olsson@its.uu.se>
Signed-off-by: David S. Miller <davem@davemloft.net>

pktgen: random flow

Random flow generation has not worked. This fixes it.

Signed-off-by: Robert Olsson <robert.olsson@its.uu.se>
Signed-off-by: David S. Miller <davem@davemloft.net>

bridge: Eliminate unnecessary forward delay

From: Stephen Hemminger <shemminger@vyatta.com>

Based upon original patch by Herbert Xu, which contained
the following problem description:

--------------------
When the forward delay is set to zero, we still delay the setting
of the forwarding state by one or possibly two timers depending
on whether STP is enabled.  This could either turn out to be
instantaneous, or horribly slow depending on the load of the
machine.

As there is nothing preventing us from enabling forwarding straight
away, this patch eliminates this potential delay by executing the
code directly if the forward delay is zero.

The effect of this problem is that immediately after the carrier
comes on a port, the bridge will drop all packets received from
that port until it enters forwarding mode, thus causing unnecessary
packet loss.

Note that this patch doesn't fully remove the delay due to the
link watcher.  We should also check the carrier state when we
are about to drop an incoming packet because the port is disabled.
But that's for another patch.
--------------------

This version of the fix takes a different approach, in that
it just does the state change directly.

Signed-off-by: David S. Miller <davem@davemloft.net>

docbook: fix s390 fatal error after header files moved

Fix (fatal error) s390 docbook file to handle renamed header files.

Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drivers/media/video/vino.c needs v4l2-ioctl.h

mips allmodconfig:

  drivers/media/video/vino.c: In function `vino_free_buffer_with_count':
  drivers/media/video/vino.c:811: warning: passing arg 1 of `virt_to_phys' makes pointer from integer without a cast
  drivers/media/video/vino.c: In function `vino_allocate_buffer':
  drivers/media/video/vino.c:889: warning: passing arg 1 of `virt_to_phys' makes pointer from integer without a cast
  drivers/media/video/vino.c: In function `vino_ioctl':
  drivers/media/video/vino.c:4364: error: implicit declaration of function `video_usercopy'

The patch fixes the error, but not the warnings.

Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm: fix uninitialized variables for find_vma_prepare callers

gcc 4.3.0 correctly emits the following warnings.
When a vma covering addr is found, find_vma_prepare indeed returns without
setting pprev, rb_link, and rb_parent.

  mm/mmap.c: In function `insert_vm_struct':
  mm/mmap.c:2085: warning: `rb_parent' may be used uninitialized in this function
  mm/mmap.c:2085: warning: `rb_link' may be used uninitialized in this function
  mm/mmap.c:2084: warning: `prev' may be used uninitialized in this function
  mm/mmap.c: In function `copy_vma':
  mm/mmap.c:2124: warning: `rb_parent' may be used uninitialized in this function
  mm/mmap.c:2124: warning: `rb_link' may be used uninitialized in this function
  mm/mmap.c:2123: warning: `prev' may be used uninitialized in this function
  mm/mmap.c: In function `do_brk':
  mm/mmap.c:1951: warning: `rb_parent' may be used uninitialized in this function
  mm/mmap.c:1951: warning: `rb_link' may be used uninitialized in this function
  mm/mmap.c:1949: warning: `prev' may be used uninitialized in this function
  mm/mmap.c: In function `mmap_region':
  mm/mmap.c:1092: warning: `rb_parent' may be used uninitialized in this function
  mm/mmap.c:1092: warning: `rb_link' may be used uninitialized in this function
  mm/mmap.c:1089: warning: `prev' may be used uninitialized in this function

Hugh adds: in fact, none of find_vma_prepare's callers use those values
when a vma is found to be already covering addr, it's either an error or
an occasion to munmap and repeat.  Okay, let's quieten the compiler (but I
would prefer it if pprev, rb_link and rb_parent were meaningful in that
case, rather than whatever's in them from descending the tree).

Signed-off-by: Benny Halevy <bhalevy@panasas.com>
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Cc: "Ryan Hope" <rmh3093@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

pm_qos: spelling fixes

A documentation cleanup patch.  With a minor tweak to clarify units for
kbs.

[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: mark gross <mgross@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

proc: fix warnings

proc: fix warnings

 fs/proc/base.c:2429: warning: format '%llu' expects type 'long long unsigned int', but argument 3 has type 'u64'
 fs/proc/base.c:2429: warning: format '%llu' expects type 'long long unsigned int', but argument 4 has type 'u64'
 fs/proc/base.c:2429: warning: format '%llu' expects type 'long long unsigned int', but argument 5 has type 'u64'
 fs/proc/base.c:2429: warning: format '%llu' expects type 'long long unsigned int', but argument 6 has type 'u64'
 fs/proc/base.c:2429: warning: format '%llu' expects type 'long long unsigned int', but argument 7 has type 'u64'
 fs/proc/base.c:2429: warning: format '%llu' expects type 'long long unsigned int', but argument 8 has type 'u64'
 fs/proc/base.c:2429: warning: format '%llu' expects type 'long long unsigned int', but argument 9 has type 'u64'

Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Acked-by: Andrea Righi <righi.andrea@gmail.com>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drivers/misc/sgi-gru/grutlbpurge.c: removed duplicated #include

Removed duplicated include <linux/delay.h> in
drivers/misc/sgi-gru/grutlbpurge.c.

Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Cc: Jack Steiner <steiner@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

omfs: fix warning

fs/omfs/inode.c:495: warning: format '%llx' expects type 'long long
unsigned int', but argument 2 has type 'u64'
fs/omfs/inode.c:495: warning: format '%llx' expects type 'long
long unsigned int', but argument 3 has type '__be64'

Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Acked-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

kernel-doc: skip nested struct/union cleanly

Fix handling of nested structs or unions.  The regex to strip (eliminate)
nested structs or unions was limited to only 0 or 1 matches.  This can
cause an uneven number of left/right braces to be stripped, which causes
this:

Warning(linux-2.6.27-rc1-git2//include/net/mac80211.h:336): No description found for parameter '}'

Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

dma: fix order calculation in dma_mark_declared_memory_occupied()

get_order() takes byte-sized input, not a page-granular one.

Irrespective of this fix I'm inclined to believe that this doesn't work
right anyway - bitmap_allocate_region() has an implicit assumption of
'pos' being suitable for 'order', which this function doesn't seem to
enforce (and since it's being called with a byte-granular value there's no
reason to believe that the callers would make sure device_addr is passed
accordingly - it's also not documented that way).

Signed-off-by: Jan Beulich <jbeulich@novell.com>
Cc: James E.J. Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Dmitry Baryshkov <dbaryshkov@gmail.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

atyfb_base.c: fix warning

drivers/video/aty/atyfb_base.c:2663: warning: 'aty_resume_chip' defined
but not used

Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Cc: Ville Syrjala <syrjala@sci.fi>
Cc: Antonino A. Daplas <adaplas@pol.net>
Cc: Mark Asselstine <asselsm@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drivers/video/fsl-diu-fb.c: add missing of_node_put

of_node_put is needed before discarding a value received from
of_find_node_by_type, eg in error handling code.

The semantic patch that makes the change is as follows:
(http://www.emn.fr/x-info/coccinelle/)

// <smpl>
@@
struct device_node *n;
struct device_node *n1;
struct device_node *n2;
statement S;
identifier f1,f2;
expression E1,E2;
constant C;
@@

n = of_find_node_by_type(...)
...
if (!n) S
... when != of_node_put(n)
    when != n1 = f1(n,...)
    when != E1 = n
    when any
    when strict
(
+ of_node_put(n);
  return -C;
|
  of_node_put(n);
|
  n2 = f2(n,...)
|
  E2 = n
|
  return ...;
)
// </smpl>

Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: Timur Tabi <timur@freescale.com>
Cc: York Sun <yorksun@freescale.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

radeonfb: give i2c buses nicer names

The name of the i2c buses shows in the output of "i2cdetect -l", so
it's important to give informative names.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

fbcon: fix scrolling after logo is cleared

If the 'clear' command is used on the frame buffer with a logo the upper
area is filled by few lines but not scrolled anymore.

Fix this by removing the protected area for the logo if any part of the
logo is cleared.

Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

radeon: misc corrections

I have a new PCI-E radeon RV380 series card (PCI device ID 5b64) that
hangs in my sparc64 boxes when the init scripts set the font.  The problem
goes away if I disable acceleration.

I haven't figured out that bug yet, but along the way I found some
corrections to make based upon some auditing.

1) The RB2D_DC_FLUSH_ALL value used by the kernel fb driver
   and the XORG video driver differ.  I've made the kernel
   match what XORG is using.

2) In radeonfb_engine_reset() we have top-level code structure
   that roughly looks like:

if (family is 300, 350, or V350)
do this;
else
do that;
...
if (family is NOT 300, OR
    family is NOT 350, OR
    family is NOT V350)
do another thing;

   this last conditional makes no sense, is always true,
   and obviously was likely meant to be "family is NOT
   300, 350, or V350".  So I've made the code match the
   intent.

Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Tested-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Remove the deprecated cli() sti() functions

These functions have been deprecated for some time now but remained until
all legacy callers could be removed.  With a few commits in 2.6.26 this
has happened so now we can remove these deprecated functions.

Signed-off-by: Mark Asselstine <mark.asselstine@windriver.com>
Reviewed-by: Matthew Wilcox <willy@linux.intel.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

backlight: add MODULE_ALIAS() to pwm_backlight driver

Add the missing MODULE_ALIAS() to the pwm_backlight driver.

Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

backlight: add more information output to pwm_backlight

Make the error paths in the pwm_backlight driver more informative in the
probe path, especially for the times that it finds an error.

Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Cc: Richard Purdie <rpurdie@rpsys.net>
Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

blackfin RTC driver: drop PIE/stopwatch code since the hardware can only do a max of 1HZ and this same functionality is provided by UIE

Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Cc: David Brownell <david-b@pacbell.net>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

blackfin RTC driver: convert PIE handling to irq_set_state() as pointed out by David Brownell

Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Cc: David Brownell <david-b@pacbell.net>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

blackfin RTC driver: wait for the write complete interrupt complete before sleeping

Since we use the write complete interrupt, wait for it
to complete before sleeping so we don't wake right back up due to it

Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Cc: David Brownell <david-b@pacbell.net>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

blackfin RTC driver: disable the write complete irq upon close

Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Cc: David Brownell <david-b@pacbell.net>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

blackfin RTC driver: don't bother passing the rtc struct down to bfin_rtc_int_{set,clear} since it isnt needed (shaves off ~100bytes)

Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Cc: David Brownell <david-b@pacbell.net>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

blackfin RTC driver: add support for power management framework

Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Cc: David Brownell <david-b@pacbell.net>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

blackfin RTC driver: Fix bug Only RTC interrupt can wake up deeper sleep core

Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Cc: David Brownell <david-b@pacbell.net>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

blackfin RTC driver: if we dont define irq_set_freq, the common rtc-dev layer will give us the same behavior of returning ENOTTY

Signed-off-by: Mike Frysinger <michael.frysinger@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Cc: David Brownell <david-b@pacbell.net>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

genirq: better warning on irqchip->set_type() failure

While I'm glad to finally see the hole fixed whereby passing an invalid
IRQ trigger type to request_irq() would be ignored, the current diagnostic
isn't quite useful.  Fixed by also listing the trigger type which was
rejected.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Uwe Kleine-König <Uwe.Kleine-Koenig@digi.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

semaphore: __down_common: use signal_pending_state()

Change __down_common() to use signal_pending_state() instead of open
coding.

The changes in kernel/semaphore.o are just artifacts, the state checks are
optimized away.

Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Matthew Wilcox <matthew@wil.cx>
Cc: Roland McGrath <roland@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

relay: fix "full buffer with exactly full last subbuffer" accounting problem

In relay's current read implementation, if the buffer is completely full
but hasn't triggered the buffer-full condition (i.e. the last write
didn't cross the subbuffer boundary) and the last subbuffer is exactly
full, the subbuffer accounting code erroneously finds nothing available.
This patch fixes the problem.

Signed-off-by: Tom Zanussi <tzanussi@gmail.com>
Cc: Eduard - Gabriel Munteanu <eduard.munteanu@linux360.ro>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Mathieu Desnoyers <compudj@krystal.dyndns.org>
Cc: Andrea Righi <righi.andrea@gmail.com>
Cc: <stable@kernel.org> [2.6.25.x, 2.6.26.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

spi: new orion_spi driver

This adds an SPI driver for the SPI controller found in various Marvell
Orion ARM SoCs.  It currently supports only one slave, which must use SPI
mode 0.

[dbrownell@users.sourceforge.net: cleanups, meet specs, pass "sparse"]
Signed-off-by: Shadi Ammouri <shadi@marvell.com>
Signed-off-by: Saeed Bishara <saeed@marvell.com>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

block/cciss.c: remove pointless curr_queue calculation

curr_queue is a local variable in a for loop, and it's being initialized
at the start of each loop.  So any assignment at the end of the loop is
pointless.

Signed-off-by: Hannes Reinecke <hare@suse.de>
Cc: Mike Miller <mike.miller@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

vt8623fb: fix kernel oops

commit 20e061fb750d36ec0ffcb2e44ed7dafa9018223b
  Author: Ondrej Zajicek <santiago@crfreenet.org>
  Date:   Mon Apr 28 02:15:18 2008 -0700

      fbdev: framebuffer_alloc() fixes

      Correct the dev arg of framebuffer_alloc() in arkfb, s3fb and vt8623fb.

causes a null-pointer deref because "info->dev is NULL, info was just
kzallocated".

Signed-off-by: Ondrej Zajicek <santiago@crfreenet.org>
Reported-by: "MadLoisae@gmx.net" <MadLoisae@gmx.net>
Tested-by: "MadLoisae@gmx.net" <MadLoisae@gmx.net>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Cc: <stable@kernel.org> [2.6.26.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

kdump: report actual value of VMCOREINFO_OSRELEASE in VMCOREINFO

The current implementation reports the structure name as
VMCOREINFO_OSRELEASE in VMCOREINFO, e.g.

        VMCOREINFO_OSRELEASE=init_uts_ns.name.release

That doesn't make sense because it's always the same. Instead, use the
value, e.g.

        VMCOREINFO_OSRELEASE=2.6.26-rc3

That's also what the 'makedumpfile -g' does.

Signed-off-by: Bernhard Walle <bwalle@suse.de>
Cc: "Ken'ichi Ohmichi" <oomichi@mxs.nes.nec.co.jp>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

powerpc: 86xx: mpc8610_hpcd: add watchdog node

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Wim Van Sebroeck <wim@iguana.be>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm_init.c: avoid ifdef-inside-macro-expansion

gcc-3.2:

  mm/mm_init.c:77:1: directives may not be used inside a macro argument
  mm/mm_init.c:76:47: unterminated argument list invoking macro "mminit_dprintk"
  mm/mm_init.c: In function `mminit_verify_pageflags_layout':
  mm/mm_init.c:80: `mminit_dprintk' undeclared (first use in this function)
  mm/mm_init.c:80: (Each undeclared identifier is reported only once
  mm/mm_init.c:80: for each function it appears in.)
  mm/mm_init.c:80: syntax error before numeric constant

Also fix a typo in a comment.

Reported-by: Adrian Bunk <bunk@kernel.org>
Cc: Mel Gorman <mel@csn.ul.ie>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Merge git://git./linux/kernel/git/bart/ide-2.6

* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6:
  ide: ->cable_detect method cannot be marked __devinit
  ide: ->quirkproc method cannot be marked __devinit
  cs5520: add enablebits checking
  cdrom: don't check CDC_PLAY_AUDIO in cdrom_count_tracks()
  ide-cd: fix endianity for the error message in cdrom_read_capacity
  ide: remove CONFIG_IDE_MAX_HWIFS
  remove unneeded #include <linux/ide.h>'s
  ide: fix regression caused by ide_device_{get,put}() addition (take 2)
  remove unnecessary <linux/hdreg.h> includes
  ide: sanitize struct ide_port_ops documentation (take 2)
  ide: fix ide_fix_driveid()
  ide: fix pre-EIDE SWDMA support on big-endian

Fix USB storage hang on command abort

Okay, I found the cause of the hang.  It is a simple bug in the USB
scatter-gather library, caused by changes added in response to the S-G
chaining modification.

This patch (as1125) fixes a bug in the USB scatter-gather library.
Early exit from the S-G initialization loop does not reset the count of
outstanding URBs.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Cc: David Brownell <david-b@pacbell.net>
Cc: Alan Jenkins <alan-jenkins@tuffmail.co.uk>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

ide: ->cable_detect method cannot be marked __devinit

Now that we have warm-plug support ->cable_detect method no longer
can be be marked __devinit.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

ide: ->quirkproc method cannot be marked __devinit

Now that we have warm-plug support ->quirkproc method no longer
can be be marked __devinit.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

cs5520: add enablebits checking

Based on sparse comments in OpenFirmware code
(no Cx5510/Cx5520 datasheet here).

This fixes 2.6.26 regression reported by TAKADA
and caused by addition of warm-plug support.

Tested-by: TAKADA Yoshihito <takada@mbf.nifty.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

cdrom: don't check CDC_PLAY_AUDIO in cdrom_count_tracks()

According to MMC-3 (or any later versions) READ TOCs are mandatory
commands and have nothing to do with CDC_PLAY_AUDIO.  I have no idea why
the check was put there in the first place but it now only breaks
automatic actions on certain drives.

Note that this test was only effective when ide-cdrom was being used
as sr didn't mask CDC_PLAY_AUDIO according to the capabilities.

Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Jens Axboe <jens.axboe@oracle.com>
Cc: Borislav Petkov <petkovbb@googlemail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

ide-cd: fix endianity for the error message in cdrom_read_capacity

Aesthetic regards aside, commit e8e7b9eb11c34ee18bde8b7011af41938d1ad667
still leaves a bug in the error message, because it uses the unconverted
big-endian value for printk.

Fix this by using a local variable in machine byte order. The result is
correct, more readable, and also produces slightly shorter code on i386.

Signed-off-by: Petr Tesarik <ptesarik@suse.cz>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Jan Kara <jack@suse.cz>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: <stable@kernel.org>
Acked-by: Borislav Petkov <petkovbb@gmail.com>
[bart: __u32 -> u32]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

ide: remove CONFIG_IDE_MAX_HWIFS

The benefits of a user settable CONFIG_IDE_MAX_HWIFS have become pretty
tiny and are no longer considered worth the trouble of an own option.

Simply always #define MAX_HWIFS to 10.

Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

remove unneeded #include <linux/ide.h>'s

This patch remove unneeded #include <linux/ide.h>'s.

It also adds a required #include <linux/interrupt.h> that was previously
implicitely pulled by ide.h

Signed-off-by: Adrian Bunk <bunk@kernel.org>
[bart: revert change to tests/lkdtm.c (spotted by Stephen Rothwell)]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

ide: fix regression caused by ide_device_{get,put}() addition (take 2)

On Monday 28 July 2008, Benjamin Herrenschmidt wrote:

[...]

> Vector: 300 (Data Access) at [c58b7b80]
>     pc: c014f264: elv_may_queue+0x10/0x44
>     lr: c0152750: get_request+0x2c/0x2c0
>     sp: c58b7c30
>    msr: 1032
>    dar: c
>  dsisr: 40000000
>   current = 0xc58aaae0
>     pid   = 854, comm = media-bay
> enter ? for help
> mon> t
> [c58b7c40] c0152750 get_request+0x2c/0x2c0
> [c58b7c70] c0152a08 get_request_wait+0x24/0xec
> [c58b7cc0] c0225674 ide_cd_queue_pc+0x58/0x1a0
> [c58b7d40] c022672c ide_cdrom_packet+0x9c/0xdc
> [c58b7d70] c0261810 cdrom_get_disc_info+0x60/0xd0
> [c58b7dc0] c026208c cdrom_mrw_exit+0x1c/0x11c
> [c58b7e30] c0260f7c unregister_cdrom+0x84/0xe8
> [c58b7e50] c022395c ide_cd_release+0x80/0x84
> [c58b7e70] c0163650 kref_put+0x54/0x6c
> [c58b7e80] c0223884 ide_cd_put+0x40/0x5c
> [c58b7ea0] c0211100 generic_ide_remove+0x28/0x3c
> [c58b7eb0] c01e9d34 __device_release_driver+0x78/0xb4
> [c58b7ec0] c01e9e44 device_release_driver+0x28/0x44
> [c58b7ee0] c01e8f7c bus_remove_device+0xac/0xd8
> [c58b7f00] c01e7424 device_del+0x104/0x198
> [c58b7f20] c01e74d0 device_unregister+0x18/0x30
> [c58b7f40] c02121c4 __ide_port_unregister_devices+0x6c/0x88
> [c58b7f60] c0212398 ide_port_unregister_devices+0x38/0x80
> [c58b7f80] c0208ca4 media_bay_step+0x1cc/0x5c0
> [c58b7fb0] c0209124 media_bay_task+0x8c/0xcc
> [c58b7fd0] c00485c0 kthread+0x48/0x84
> [c58b7ff0] c0011b20 kernel_thread+0x44/0x60

The guilty commit turned out to be 08da591e14cf87247ec09b17c350235157a92fc3
("ide: add ide_device_{get,put}() helpers").  ide_device_put() is called
before kref_put() in ide_cd_put() so IDE device is already gone by the time
ide_cd_release() is reached.

Fix it by calling ide_device_get() before kref_get() and ide_device_put()
after kref_put() in all affected device drivers.

v2:
Brown paper bag time.  In v1 cd->drive was referenced after dropping last
reference on cd object (which could result in OOPS in ide_device_put() as
reported/debugged by Mariusz Kozlowski).  Fix it by caching cd->drive in
the local variable (fix other device drivers too).

Reported-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reported-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Borislav Petkov <petkovbb@gmail.com>
Tested-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Tested-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

remove unnecessary <linux/hdreg.h> includes

Following files don't need <linux/hdreg.h> at all:

- arch/mips/jazz/setup.c
- arch/sh/boards/mach-systemh/irq.c
- drivers/macintosh/mediabay.c
- drivers/scsi/hptiop.c
- drivers/usb/storage/freecom.c
- arch/powerpc/include/asm/ide.h
- init/main.c

Cc: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

ide: sanitize struct ide_port_ops documentation (take 2)

v2:
Add missing '@'-s.  (Noticed by Randy Dunlap)

Cc: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

ide: fix ide_fix_driveid()

Fix byte-swapping for id->words161_175[], id->words206_254[]
and id->words206_254[].

Luckily all words previously left in little-endian byte-order
are marked as reserved so this fix shouldn't affect user-space
applications.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

ide: fix pre-EIDE SWDMA support on big-endian

id->tDMA is of 'unsigned char' type so endianness is already
correct and calling le16_to_cpu() is wrong.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Merge branch 'no-ath9k' of git://git./linux/kernel/git/linville/wireless-2.6

bridge: fix compile warning in net/bridge/br_netfilter.c

This patch fixes the following warning due to incompatible pointer
assignment:

net/bridge/br_netfilter.c: In function 'br_netfilter_rtable_init':
net/bridge/br_netfilter.c:116: warning: assignment from incompatible
pointer type

This warning is due to commit 4adf0af6818f3ea52421dc0bae836cfaf20ef72a
from July 30 (send correct MTU value in PMTU (revised)).

Signed-off-by: Rami Rosen <ramirose@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ipv4: remove unused field in struct flowi (include/net/flow.h).

This patch removes an unused field (flags) from struct flowi; it seems
that this "flags" field was used once in the past for multipath
routing with FLOWI_FLAG_MULTIPATHOLDROUTE flag (which does no longer
exist); however, the "flags" field of struct flowi is not used
anymore.

Signed-off-by: Rami Rosen <ramirose@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tg3: Fix 'scheduling while atomic' errors

This patch fixes the 'scheduling while atomic' errors introduced by
commit 12dac0756d357325b107fe6ec24921ec38661839 ("tg3: adapt tg3 to
use reworked PCI PM code").

The first hunk of the patch removes an unnecessary
tg3_set_power_state() call.  The chip will already be in the D0 state
either due to a chip reset or through a previous call to
tg3_set_power_state().

The second hunk of the patch moves the tg3_set_power_state() call
outside the critical section guarded by tg3_full_lock() and
tg3_full_unlock() functions.  The power state of the device is and
should be outside the lock's domain and all other
tg3_set_power_state() calls support this.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: Kill plain NET_XMIT_BYPASS.

dst_input() was doing something completely absurd, looping
on skb->dst->input() if NET_XMIT_BYPASS was seen, but these
functions never return such an error.

And as a result plain ole' NET_XMIT_BYPASS has no more
references and can be completely killed off.

Signed-off-by: David S. Miller <davem@davemloft.net>

net_sched: Add qdisc __NET_XMIT_BYPASS flag

Patrick McHardy <kaber@trash.net> noticed that it would be nice to
handle NET_XMIT_BYPASS by NET_XMIT_SUCCESS with an internal qdisc flag
__NET_XMIT_BYPASS and to remove the mapping from dev_queue_xmit().

David Miller <davem@davemloft.net> spotted a serious bug in the first
version of this patch.

Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net_sched: Add qdisc __NET_XMIT_STOLEN flag

Patrick McHardy <kaber@trash.net> noticed:
"The other problem that affects all qdiscs supporting actions is
TC_ACT_QUEUED/TC_ACT_STOLEN getting mapped to NET_XMIT_SUCCESS
even though the packet is not queued, corrupting upper qdiscs'
qlen counters."

and later explained:
"The reason why it translates it at all seems to be to not increase
the drops counter. Within a single qdisc this could be avoided by
other means easily, upper qdiscs would still increase the counter
when we return anything besides NET_XMIT_SUCCESS though.

This means we need a new NET_XMIT return value to indicate this to
the upper qdiscs. So I'd suggest to introduce NET_XMIT_STOLEN,
return that to upper qdiscs and translate it to NET_XMIT_SUCCESS
in dev_queue_xmit, similar to NET_XMIT_BYPASS."

David Miller <davem@davemloft.net> noticed:
"Maybe these NET_XMIT_* values being passed around should be a set of
bits. They could be composed of base meanings, combined with specific
attributes.

So you could say "NET_XMIT_DROP | __NET_XMIT_NO_DROP_COUNT"

The attributes get masked out by the top-level ->enqueue() caller,
such that the base meanings are the only thing that make their
way up into the stack. If it's only about communication within the
qdisc tree, let's simply code it that way."

This patch is trying to realize these ideas.

Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

fs: rename buffer trylock

Like the page lock change, this also requires name change, so convert the
raw test_and_set bitop to a trylock.

Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm: rename page trylock

Converting page lock to new locking bitops requires a change of page flag
operation naming, so we might as well convert it to something nicer
(!TestSetPageLocked_Lock => trylock_page, SetPageLocked => set_page_locked).

This also facilitates lockdeping of page lock.

Signed-off-by: Nick Piggin <npiggin@suse.de>
Acked-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Acked-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Merge git://git./linux/kernel/git/davem/sparc-2.6

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
  sparc64: Remove all cpumask_t local variables in xcall dispatch.
  sparc64: Kill error_mask from hypervisor_xcall_deliver().
  sparc64: Build cpu list and mondo block at top-level xcall_deliver().
  sparc64: Disable local interrupts around xcall_deliver_impl() invocation.
  sparc64: Make all xcall_deliver's go through common helper function.
  sparc64: Always allocate the send mondo blocks, even on non-sun4v.
  sparc64: Make smp_cross_call_masked() take a cpumask_t pointer.
  sparc64: Directly call xcall_deliver() in smp_start_sync_tick_client.
  sparc64: Call xcall_deliver() directly in some cases.
  sparc64: Use cpumask_t pointers and for_each_cpu_mask_nr() in xcall_deliver.
  sparc64: Use xcall_deliver() consistently.
  sparc64: Use function pointer for cross-call sending.
  arch/sparc64/kernel/signal.c: removed duplicated #include
  sparc64: Need to disable preemption around smp_tsb_sync().

Merge git://git./linux/kernel/git/lethal/sh-2.6

* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (29 commits)
  sh: enable maple_keyb in dreamcast_defconfig.
  SH2(A) cache update
  nommu: Provide vmalloc_exec().
  add addrespace definition for sh2a.
  sh: Kill off ARCH_SUPPORTS_AOUT and remnants of a.out support.
  sh: define GENERIC_HARDIRQS_NO__DO_IRQ.
  sh: define GENERIC_LOCKBREAK.
  sh: Save NUMA node data in vmcore for crash dumps.
  sh: module_alloc() should be using vmalloc_exec().
  sh: Fix up __bug_table handling in module loader.
  sh: Add documentation and integrate into docbook build.
  sh: Fix up broken kerneldoc comments.
  maple: Kill useless private_data pointer.
  maple: Clean up maple_driver_register/unregister routines.
  input: Clean up maple keyboard driver
  maple: allow removal and reinsertion of keyboard driver module
  sh: /proc/asids depends on MMU.
  arch/sh/boards/mach-se/7343/irq.c: removed duplicated #include
  arch/sh/boards/board-ap325rxa.c: removed duplicated #include
  sh/boards/Makefile typo fix
  ...

Merge branch 'merge' of git://git./linux/kernel/git/paulus/powerpc

* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
  powerpc: Remove use of CONFIG_PPC_MERGE
  powerpc: Force printing of 'total_memory' to unsigned long long
  powerpc: Fix compiler warning in arch/powerpc/mm/mem.c
  powerpc: Move include files to arch/powerpc/include/asm

Merge git://git./linux/kernel/git/sam/kbuild-fixes

* git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild-fixes:
  kconfig: drop the ""trying to assign nonexistent symbol" warning
  kconfig: always write out .config

tracehook: kerneldoc fix

My last change to tracehook.h made it confuse the kerneldoc parser.
Move the #define's before the comment so it's happy again.

Signed-off-by: Roland McGrath <roland@redhat.com>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mn10300: Fix up __bug_table handling in module loader.

Platforms that are using GENERIC_BUG must call in to
module_bug_finalize()/module_bug_cleanup() in order to scan modules with
their own __bug_table sections that are otherwise unaccounted.

Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Merge branch 'audit.b56' of git://git./linux/kernel/git/viro/audit-current

* 'audit.b56' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/audit-current:
  Re: [PATCH] Fix the kernel panic of audit_filter_task when key field is set

Merge git://git./linux/kernel/git/jejb/scsi-rc-fixes-2.6

* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
  [SCSI] scsi_transport_spi: fix oops in revalidate
  [SCSI] ses: fix VPD inquiry overrun
  [SCSI] block: Fix miscalculation of sg_io timeout in CDROM_SEND_PACKET handler.
  [SCSI] hptiop: add more PCI device IDs

m68k: some asm-sparc include files moved

So copy their contents into the asm-m68k files.

Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

__sched_setscheduler: don't do any policy checks when not "user"

The "user" parameter to __sched_setscheduler indicates whether the
change is being done on behalf of a user process or not.  If not, we
shouldn't apply any permissions checks, so don't call
security_task_setscheduler().

Signed-off-by: Jeremy Fitzhardinge <jeremy@goop.org>
Tested-by: Steve Wise <swise@opengridcomputing.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Merge branch 'for-linus' of git://git390.osdl.marist.edu/linux-2.6

* 'for-linus' of git://git390.osdl.marist.edu/pub/scm/linux-2.6:
  [S390] move include/asm-s390 to arch/s390/include/asm

Merge git://git./linux/kernel/git/brodo/pcmcia-fixes-2.6

* git://git.kernel.org/pub/scm/linux/kernel/git/brodo/pcmcia-fixes-2.6:
  pcmcia: rsrc_nonstatic: check value, not pointer

sc1200 watchdog driver: Fix locking, sems and coding style

Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

alpha: Fix breakage in wdt_pci

drivers/watchdog/wdt_pci.c: In function 'wdtpci_ctr_mode':
drivers/watchdog/wdt_pci.c:120: error: implicit declaration of function 'udelay'
{standard input}: Assembler messages:

Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

wdt: Cleanup and sort out locking and inb_p

Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

s3c2410_wdt watchdog driver: Locking and coding style

Kill off use of semaphores.
Fix ioctl races and locking holes.

From: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

it8712f_wdt: Locking and coding style

Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

ar7_wdt watchdog driver: Fix locking

Use unlocked_ioctl
Remove semaphores

Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

vt: Deadlock workaround

2.6.26 corrected the mutex locking on tty resizing to fix the case where
you could get the tty/vt sizing out of sync. That turns out to have a
deadlock.

The actual fix is really major and I've got it lined up as part of the ops
changes for 2.6.28 so for 2.6.26/2.6.27 it is safer to reintroduce this
ages old minor bug.

Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

cris: Fixup compile problems

It now compiles with the tty changes but isn't tested (which has to be
better than not compiling..

Closes bug #11218

Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

blackfin: Fix compile failure in tty code

Blackfin peers into the ldisc in an odd way for IRDA snooping which
therefore got missed. Simple enough fix.

Closes bug #11233

Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Merge git://git.infradead.org/users/dwmw2/random-2.6

* git://git.infradead.org/users/dwmw2/random-2.6:
  drivers/video/console/promcon.c: fix build error
  Fix IHEX firmware generation/loading

sound: ensure device number is valid in snd_seq_oss_synth_make_info

snd_seq_oss_synth_make_info() incorrectly reports information
to userspace without first checking for the validity of the
device number, leading to possible information leak (CVE-2008-3272).

Reported-By: Tobias Klein <tk@trapkit.de>
Acked-and-tested-by: Takashi Iwai <tiwai@suse.de>
Cc: stable@kernel.org
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Merge git://git./linux/kernel/git/kkeil/ISDN-2.6

* git://git.kernel.org/pub/scm/linux/kernel/git/kkeil/ISDN-2.6:
  Add DIP switch readout for HFC-4S IOB4ST
  Fix remaining big endian issue of hfcmulti
  mISDN cleanup user interface
  mISDN fix main ISDN Makefile