review.tizen.org Git - platform/kernel/linux-rpi.git/log

devlink: Add enable_remote_dev_reset generic parameter

The enable_remote_dev_reset devlink param flags that the host admin
allows device resets that can be initiated by other hosts. This
parameter is useful for setups where a device is shared by different
hosts, such as multi-host setup. Once the user set this parameter to
false, the driver should NACK any attempt to reset the device while the
driver is loaded.

Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net/mlx5: Add support for devlink reload action fw activate

Add support for devlink reload action fw_activate. To activate firmware
image the mlx5 driver resets the firmware and reloads it from flash. If
a new image was stored on flash it will be loaded. Once this reload
command is executed the driver initiates fw sync reset flow, where the
firmware synchronizes all PFs on coming reset and driver reload.

Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net/mlx5: Handle sync reset abort event

If firmware sends sync_reset_abort to driver the driver should clear the
reset requested mode as reset is not expected any more.

Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net/mlx5: Handle sync reset now event

On sync_reset_now event the driver does reload and PCI link toggle to
activate firmware upgrade reset. When the firmware sends this event it
syncs the event on all PFs, so all PFs will do PCI link toggle at once.
To do PCI link toggle, the driver ensures that no other device ID under
the same bridge by checking that all the PF functions under the same PCI
bridge have same device ID. If no other device it uses PCI bridge link
control to turn link down and up.

Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net/mlx5: Handle sync reset request event

Once the driver gets sync_reset_request from firmware it prepares for the
coming reset and sends acknowledge.
After getting this event the driver expects device reset, either it will
trigger PCI reset on sync_reset_now event or such PCI reset will be
triggered by another PF of the same device. So it moves to reset
requested mode and if it gets PCI reset triggered by the other PF it
detect the reset and reloads.

Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net/mlx5: Set cap for pci sync for fw update event

Set capability to notify the firmware that this host driver is capable
of handling pci sync for firmware update events.

Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net/mlx5: Add functions to set/query MFRL register

Add functions to query and set the MFRL reset options supported by
firmware.

Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

devlink: Add remote reload stats

Add remote reload stats to hold the history of actions performed due
devlink reload commands initiated by remote host. For example, in case
firmware activation with reset finished successfully but was initiated
by remote host.

The function devlink_remote_reload_actions_performed() is exported to
enable drivers update on remote reload actions performed as it was not
initiated by their own devlink instance.

Expose devlink remote reload stats to the user through devlink dev get
command.

Examples:
$ devlink dev show
pci/0000:82:00.0:
  stats:
      reload:
        driver_reinit 2 fw_activate 1 fw_activate_no_reset 0
      remote_reload:
        driver_reinit 0 fw_activate 0 fw_activate_no_reset 0
pci/0000:82:00.1:
  stats:
      reload:
        driver_reinit 1 fw_activate 0 fw_activate_no_reset 0
      remote_reload:
        driver_reinit 1 fw_activate 1 fw_activate_no_reset 0

$ devlink dev show -jp
{
    "dev": {
        "pci/0000:82:00.0": {
            "stats": {
                "reload": {
                    "driver_reinit": 2,
                    "fw_activate": 1,
                    "fw_activate_no_reset": 0
                },
                "remote_reload": {
                    "driver_reinit": 0,
                    "fw_activate": 0,
                    "fw_activate_no_reset": 0
                }
            }
        },
        "pci/0000:82:00.1": {
            "stats": {
                "reload": {
                    "driver_reinit": 1,
                    "fw_activate": 0,
                    "fw_activate_no_reset": 0
                },
                "remote_reload": {
                    "driver_reinit": 1,
                    "fw_activate": 1,
                    "fw_activate_no_reset": 0
                }
            }
        }
    }
}

Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

devlink: Add reload stats

Add reload stats to hold the history per reload action type and limit.

For example, the number of times fw_activate has been performed on this
device since the driver module was added or if the firmware activation
was performed with or without reset.

Add devlink notification on stats update.

Expose devlink reload stats to the user through devlink dev get command.

Examples:
$ devlink dev show
pci/0000:82:00.0:
  stats:
      reload:
        driver_reinit 2 fw_activate 1 fw_activate_no_reset 0
pci/0000:82:00.1:
  stats:
      reload:
        driver_reinit 1 fw_activate 0 fw_activate_no_reset 0

$ devlink dev show -jp
{
    "dev": {
        "pci/0000:82:00.0": {
            "stats": {
                "reload": {
                    "driver_reinit": 2,
                    "fw_activate": 1,
                    "fw_activate_no_reset": 0
                }
            }
        },
        "pci/0000:82:00.1": {
            "stats": {
                "reload": {
                    "driver_reinit": 1,
                    "fw_activate": 0,
                    "fw_activate_no_reset": 0
                }
            }
        }
    }
}

Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

devlink: Add devlink reload limit option

Add reload limit to demand restrictions on reload actions.
Reload limits supported:
no_reset: No reset allowed, no down time allowed, no link flap and no
configuration is lost.

By default reload limit is unspecified and so no constraints on reload
actions are required.

Some combinations of action and limit are invalid. For example, driver
can not reinitialize its entities without any downtime.

The no_reset reload limit will have usecase in this patchset to
implement restricted fw_activate on mlx5.

Have the uapi parameter of reload limit ready for future support of
multiselection.

Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

devlink: Add reload action option to devlink reload command

Add devlink reload action to allow the user to request a specific reload
action. The action parameter is optional, if not specified then devlink
driver re-init action is used (backward compatible).
Note that when required to do firmware activation some drivers may need
to reload the driver. On the other hand some drivers may need to reset
the firmware to reinitialize the driver entities. Therefore, the devlink
reload command returns the actions which were actually performed.
Reload actions supported are:
driver_reinit: driver entities re-initialization, applying devlink-param
               and devlink-resource values.
fw_activate: firmware activate.

command examples:
$devlink dev reload pci/0000:82:00.0 action driver_reinit
reload_actions_performed:
  driver_reinit

$devlink dev reload pci/0000:82:00.0 action fw_activate
reload_actions_performed:
  driver_reinit fw_activate

Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

devlink: Change devlink_reload_supported() param type

Change devlink_reload_supported() function to get devlink_ops pointer
param instead of devlink pointer param.
This change will be used in the next patch to check if devlink reload is
supported before devlink instance is allocated.

Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net/sched: get rid of qdisc->padded

kmalloc() of sufficiently big portion of memory is cache-aligned
in regular conditions. If some debugging options are used,
there is no reason qdisc structures would need 64-byte alignment
if most other kernel structures are not aligned.

This get rid of QDISC_ALIGN and QDISC_ALIGNTO.

Addition of privdata field will help implementing
the reverse of qdisc_priv() and documents where
the private data is.

Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Allen Pais <allen.lkml@gmail.com>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

selftests: mptcp: interpret \n as a new line

In case of errors, this message was printed:

  (...)
  balanced bwidth with unbalanced delay       5233 max 5005  [ fail ]
  client exit code 0, server 0
  \nnetns ns3-0-EwnkPH socket stat for 10003:
  (...)

Obviously, the idea was to add a new line before the socket stat and not
print "\nnetns".

The commit 8b974778f998 ("selftests: mptcp: interpret \n as a new line")
is very similar to this one. But the modification in simult_flows.sh was
missed because this commit above was done in parallel to one here below.

Fixes: 1a418cb8e888 ("mptcp: simult flow self-tests")
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: mscc: ocelot: add missing VCAP ES0 and IS1 regmaps for VSC7514

Without these definitions, the driver will crash in:
mscc_ocelot_probe
-> ocelot_init
-> ocelot_vcap_init
-> __ocelot_target_read_ix

I missed this because I did not have the VSC7514 hardware to test, only
the VSC9959 and VSC9953, and the probing part is different.

Fixes: e3aea296d86f ("net: mscc: ocelot: add definitions for VCAP ES0 keys, actions and target")
Fixes: a61e365d7c18 ("net: mscc: ocelot: add definitions for VCAP IS1 keys, actions and target")
Reported-by: Divya Koppera <Divya.Koppera@microchip.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

mptcp: fix infinite loop on recvmsg()/worker() race.

If recvmsg() and the workqueue race to dequeue the data
pending on some subflow, the current mapping for such
subflow covers several skbs and some of them have not
reached yet the received, either the worker or recvmsg()
can find a subflow with the data_avail flag set - since
the current mapping is valid and in sequence - but no
skbs in the receive queue - since the other entity just
processed them.

The above will lead to an unbounded loop in __mptcp_move_skbs()
and a subsequent hang of any task trying to acquiring the msk
socket lock.

This change addresses the issue stopping the __mptcp_move_skbs()
loop as soon as we detect the above race (empty receive queue
with data_avail set).

Reported-and-tested-by: syzbot+fcf8ca5817d6e92c6567@syzkaller.appspotmail.com
Fixes: ab174ad8ef76 ("mptcp: move ooo skbs into msk out of order queue.")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

cxgb4: convert tasklets to use new tasklet_setup() API

In preparation for unconditionally passing the
struct tasklet_struct pointer to all tasklet
callbacks, switch to using the new tasklet_setup()
and from_tasklet() to pass the tasklet pointer explicitly.

Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: Allen Pais <apais@linux.microsoft.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

ethtool: correct policy for ETHTOOL_MSG_CHANNELS_SET

This accidentally got wired up to the *get* policy instead
of the *set* policy, causing operations to be rejected. Fix
it by wiring up the correct policy instead.

Fixes: 5028588b62cb ("ethtool: wire up set policies to ops")
Reported-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Tested-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

ethtool: strset: allow ETHTOOL_A_STRSET_COUNTS_ONLY attr

The ETHTOOL_A_STRSET_COUNTS_ONLY flag attribute was previously
not allowed to be used, but now due to the policy size reduction
we would access the tb[] array out of bounds since we tried to
check for the attribute despite it not being accepted.

Fix both issues by adding it correctly to the appropriate policy.

Fixes: ff419afa4310 ("ethtool: trim policy tables")
Fixes: 71921690f974 ("ethtool: provide string sets with STRSET_GET request")
Reported-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Tested-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Merge git://git./linux/kernel/git/netdev/net

Small conflict around locking in rxrpc_process_event() -
channel_lock moved to bundle in next, while state lock
needs _bh() from net.

Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Merge tag 'for_linus' of git://git./linux/kernel/git/mst/vhost

Pull vhost fixes from Michael Tsirkin:
"Some last minute vhost,vdpa fixes.

  The last two of them haven't been in next but they do seem kind of
  obvious, very small and safe, fix bugs reported in the field, and they
  are both in a new mlx5 vdpa driver, so it's not like we can introduce
  regressions"

* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
  vdpa/mlx5: Fix dependency on MLX5_CORE
  vdpa/mlx5: should keep avail_index despite device status
  vhost-vdpa: fix page pinning leakage in error path
  vhost-vdpa: fix vhost_vdpa_map() on error condition
  vhost: Don't call log_access_ok() when using IOTLB
  vhost: Use vhost_get_used_size() in vhost_vring_set_addr()
  vhost: Don't call access_ok() when using IOTLB
  vhost vdpa: fix vhost_vdpa_open error handling

Merge git://git./linux/kernel/git/netdev/net

Pull networking fixes from Jakub Kicinski:
"One more set of fixes from the networking tree:

   - add missing input validation in nl80211_del_key(), preventing
     out-of-bounds access

   - last minute fix / improvement of a MRP netlink (uAPI) interface
     introduced in 5.9 (current) release

   - fix "unresolved symbol" build error under CONFIG_NET w/o
     CONFIG_INET due to missing tcp_timewait_sock and inet_timewait_sock
     BTF.

   - fix 32 bit sub-register bounds tracking in the bpf verifier for OR
     case

   - tcp: fix receive window update in tcp_add_backlog()

   - openvswitch: handle DNAT tuple collision in conntrack-related code

   - r8169: wait for potential PHY reset to finish after applying a FW
     file, avoiding unexpected PHY behaviour and failures later on

   - mscc: fix tail dropping watermarks for Ocelot switches

   - avoid use-after-free in macsec code after a call to the GRO layer

   - avoid use-after-free in sctp error paths

   - add a device id for Cellient MPL200 WWAN card

   - rxrpc fixes:
      - fix the xdr encoding of the contents read from an rxrpc key
      - fix a BUG() for a unsupported encoding type.
      - fix missing _bh lock annotations.
      - fix acceptance handling for an incoming call where the incoming
        call is encrypted.
      - the server token keyring isn't network namespaced - it belongs
        to the server, so there's no need. Namespacing it means that
        request_key() fails to find it.
      - fix a leak of the server keyring"

* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (21 commits)
  net: usb: qmi_wwan: add Cellient MPL200 card
  macsec: avoid use-after-free in macsec_handle_frame()
  r8169: consider that PHY reset may still be in progress after applying firmware
  openvswitch: handle DNAT tuple collision
  sctp: fix sctp_auth_init_hmacs() error path
  bridge: Netlink interface fix.
  net: wireless: nl80211: fix out-of-bounds access in nl80211_del_key()
  bpf: Fix scalar32_min_max_or bounds tracking
  tcp: fix receive window update in tcp_add_backlog()
  net: usb: rtl8150: set random MAC address when set_ethernet_addr() fails
  mptcp: more DATA FIN fixes
  net: mscc: ocelot: warn when encoding an out-of-bounds watermark value
  net: mscc: ocelot: divide watermark value by 60 when writing to SYS_ATOP
  net: qrtr: ns: Fix the incorrect usage of rcu_read_lock()
  rxrpc: Fix server keyring leak
  rxrpc: The server keyring isn't network-namespaced
  rxrpc: Fix accept on a connection that need securing
  rxrpc: Fix some missing _bh annotations on locking conn->state_lock
  rxrpc: Downgrade the BUG() for unsupported token type in rxrpc_read()
  rxrpc: Fix rxkad token xdr encoding
  ...

vdpa/mlx5: Fix dependency on MLX5_CORE

Remove propmt for selecting MLX5_VDPA by the user and modify
MLX5_VDPA_NET to select MLX5_VDPA. Also modify MLX5_VDPA_NET to depend
on mlx5_core.

This fixes an issue where configuration sets 'y' for MLX5_VDPA_NET while
MLX5_CORE is compiled as a module causing link errors.

Reported-by: kernel test robot <lkp@intel.com>
Fixes: 1a86b377aa21 ("vdpa/mlx5: Add VDPA driver for supported mlx5 device")s
Signed-off-by: Eli Cohen <elic@nvidia.com>
Link: https://lore.kernel.org/r/20201007064011.GA50074@mtl-vdi-166.wap.labs.mlnx
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>

vdpa/mlx5: should keep avail_index despite device status

A VM with mlx5 vDPA has below warnings while being reset:

vhost VQ 0 ring restore failed: -1: Resource temporarily unavailable (11)
vhost VQ 1 ring restore failed: -1: Resource temporarily unavailable (11)

We should allow userspace emulating the virtio device be
able to get to vq's avail_index, regardless of vDPA device
status. Save the index that was last seen when virtq was
stopped, so that userspace doesn't complain.

Signed-off-by: Si-Wei Liu <si-wei.liu@oracle.com>
Link: https://lore.kernel.org/r/1601583511-15138-1-git-send-email-si-wei.liu@oracle.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Eli Cohen <elic@nvidia.com>

net: usb: qmi_wwan: add Cellient MPL200 card

Add usb ids of the Cellient MPL200 card.

Signed-off-by: Wilken Gottwalt <wilken.gottwalt@mailbox.org>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

macsec: avoid use-after-free in macsec_handle_frame()

De-referencing skb after call to gro_cells_receive() is not allowed.
We need to fetch skb->len earlier.

Fixes: 5491e7c6b1a9 ("macsec: enable GRO and RPS on macsec devices")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Paolo Abeni <pabeni@redhat.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

r8169: consider that PHY reset may still be in progress after applying firmware

Some firmware files trigger a PHY soft reset and don't wait for it to
be finished. PHY register writes directly after applying the firmware
may fail or provide unexpected results therefore. Fix this by waiting
for bit BMCR_RESET to be cleared after applying firmware.

There's nothing wrong with the referenced change, it's just that the
fix will apply cleanly only after this change.

Fixes: 89fbd26cca7e ("r8169: fix firmware not resetting tp->ocp_base")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

openvswitch: handle DNAT tuple collision

With multiple DNAT rules it's possible that after destination
translation the resulting tuples collide.

For example, two openvswitch flows:
nw_dst=10.0.0.10,tp_dst=10, actions=ct(commit,table=2,nat(dst=20.0.0.1:20))
nw_dst=10.0.0.20,tp_dst=10, actions=ct(commit,table=2,nat(dst=20.0.0.1:20))

Assuming two TCP clients initiating the following connections:
10.0.0.10:5000->10.0.0.10:10
10.0.0.10:5000->10.0.0.20:10

Both tuples would translate to 10.0.0.10:5000->20.0.0.1:20 causing
nf_conntrack_confirm() to fail because of tuple collision.

Netfilter handles this case by allocating a null binding for SNAT at
egress by default. Perform the same operation in openvswitch for DNAT
if no explicit SNAT is requested by the user and allocate a null binding
for SNAT for packets in the "original" direction.

Reported-at: https://bugzilla.redhat.com/1877128
Suggested-by: Florian Westphal <fw@strlen.de>
Fixes: 05752523e565 ("openvswitch: Interface with NAT.")
Signed-off-by: Dumitru Ceara <dceara@redhat.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

sctp: fix sctp_auth_init_hmacs() error path

After freeing ep->auth_hmacs we have to clear the pointer
or risk use-after-free as reported by syzbot:

BUG: KASAN: use-after-free in sctp_auth_destroy_hmacs net/sctp/auth.c:509 [inline]
BUG: KASAN: use-after-free in sctp_auth_destroy_hmacs net/sctp/auth.c:501 [inline]
BUG: KASAN: use-after-free in sctp_auth_free+0x17e/0x1d0 net/sctp/auth.c:1070
Read of size 8 at addr ffff8880a8ff52c0 by task syz-executor941/6874

CPU: 0 PID: 6874 Comm: syz-executor941 Not tainted 5.9.0-rc8-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x198/0x1fd lib/dump_stack.c:118
print_address_description.constprop.0.cold+0xae/0x497 mm/kasan/report.c:383
__kasan_report mm/kasan/report.c:513 [inline]
kasan_report.cold+0x1f/0x37 mm/kasan/report.c:530
sctp_auth_destroy_hmacs net/sctp/auth.c:509 [inline]
sctp_auth_destroy_hmacs net/sctp/auth.c:501 [inline]
sctp_auth_free+0x17e/0x1d0 net/sctp/auth.c:1070
sctp_endpoint_destroy+0x95/0x240 net/sctp/endpointola.c:203
sctp_endpoint_put net/sctp/endpointola.c:236 [inline]
sctp_endpoint_free+0xd6/0x110 net/sctp/endpointola.c:183
sctp_destroy_sock+0x9c/0x3c0 net/sctp/socket.c:4981
sctp_v6_destroy_sock+0x11/0x20 net/sctp/socket.c:9415
sk_common_release+0x64/0x390 net/core/sock.c:3254
sctp_close+0x4ce/0x8b0 net/sctp/socket.c:1533
inet_release+0x12e/0x280 net/ipv4/af_inet.c:431
inet6_release+0x4c/0x70 net/ipv6/af_inet6.c:475
__sock_release+0xcd/0x280 net/socket.c:596
sock_close+0x18/0x20 net/socket.c:1277
__fput+0x285/0x920 fs/file_table.c:281
task_work_run+0xdd/0x190 kernel/task_work.c:141
exit_task_work include/linux/task_work.h:25 [inline]
do_exit+0xb7d/0x29f0 kernel/exit.c:806
do_group_exit+0x125/0x310 kernel/exit.c:903
__do_sys_exit_group kernel/exit.c:914 [inline]
__se_sys_exit_group kernel/exit.c:912 [inline]
__x64_sys_exit_group+0x3a/0x50 kernel/exit.c:912
do_syscall_64+0x2d/0x70 arch/x86/entry/common.c:46
entry_SYSCALL_64_after_hwframe+0x44/0xa9
RIP: 0033:0x43f278
Code: Bad RIP value.
RSP: 002b:00007fffe0995c38 EFLAGS: 00000246 ORIG_RAX: 00000000000000e7
RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 000000000043f278
RDX: 0000000000000000 RSI: 000000000000003c RDI: 0000000000000000
RBP: 00000000004bf068 R08: 00000000000000e7 R09: ffffffffffffffd0
R10: 0000000020000000 R11: 0000000000000246 R12: 0000000000000001
R13: 00000000006d1180 R14: 0000000000000000 R15: 0000000000000000

Allocated by task 6874:
kasan_save_stack+0x1b/0x40 mm/kasan/common.c:48
kasan_set_track mm/kasan/common.c:56 [inline]
__kasan_kmalloc.constprop.0+0xbf/0xd0 mm/kasan/common.c:461
kmem_cache_alloc_trace+0x174/0x300 mm/slab.c:3554
kmalloc include/linux/slab.h:554 [inline]
kmalloc_array include/linux/slab.h:593 [inline]
kcalloc include/linux/slab.h:605 [inline]
sctp_auth_init_hmacs+0xdb/0x3b0 net/sctp/auth.c:464
sctp_auth_init+0x8a/0x4a0 net/sctp/auth.c:1049
sctp_setsockopt_auth_supported net/sctp/socket.c:4354 [inline]
sctp_setsockopt+0x477e/0x97f0 net/sctp/socket.c:4631
__sys_setsockopt+0x2db/0x610 net/socket.c:2132
__do_sys_setsockopt net/socket.c:2143 [inline]
__se_sys_setsockopt net/socket.c:2140 [inline]
__x64_sys_setsockopt+0xba/0x150 net/socket.c:2140
do_syscall_64+0x2d/0x70 arch/x86/entry/common.c:46
entry_SYSCALL_64_after_hwframe+0x44/0xa9

Freed by task 6874:
kasan_save_stack+0x1b/0x40 mm/kasan/common.c:48
kasan_set_track+0x1c/0x30 mm/kasan/common.c:56
kasan_set_free_info+0x1b/0x30 mm/kasan/generic.c:355
__kasan_slab_free+0xd8/0x120 mm/kasan/common.c:422
__cache_free mm/slab.c:3422 [inline]
kfree+0x10e/0x2b0 mm/slab.c:3760
sctp_auth_destroy_hmacs net/sctp/auth.c:511 [inline]
sctp_auth_destroy_hmacs net/sctp/auth.c:501 [inline]
sctp_auth_init_hmacs net/sctp/auth.c:496 [inline]
sctp_auth_init_hmacs+0x2b7/0x3b0 net/sctp/auth.c:454
sctp_auth_init+0x8a/0x4a0 net/sctp/auth.c:1049
sctp_setsockopt_auth_supported net/sctp/socket.c:4354 [inline]
sctp_setsockopt+0x477e/0x97f0 net/sctp/socket.c:4631
__sys_setsockopt+0x2db/0x610 net/socket.c:2132
__do_sys_setsockopt net/socket.c:2143 [inline]
__se_sys_setsockopt net/socket.c:2140 [inline]
__x64_sys_setsockopt+0xba/0x150 net/socket.c:2140
do_syscall_64+0x2d/0x70 arch/x86/entry/common.c:46
entry_SYSCALL_64_after_hwframe+0x44/0xa9

Fixes: 1f485649f529 ("[SCTP]: Implement SCTP-AUTH internals")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Vlad Yasevich <vyasevich@gmail.com>
Cc: Neil Horman <nhorman@tuxdriver.com>
Cc: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Merge tag 'mac80211-for-net-2020-10-08' of git://git./linux/kernel/git/jberg/mac80211

Johannes Berg says:

====================
pull-request: mac80211 2020-10-08

A single fix for missing input validation in nl80211.
====================

Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Merge git://git./pub/scm/linux/kernel/git/bpf/bpf

Daniel Borkmann says:

====================
pull-request: bpf 2020-10-08

The main changes are:

1) Fix "unresolved symbol" build error under CONFIG_NET w/o CONFIG_INET due
to missing tcp_timewait_sock and inet_timewait_sock BTF, from Yonghong Song.

2) Fix 32 bit sub-register bounds tracking for OR case, from Daniel Borkmann.
====================

Signed-off-by: Jakub Kicinski <kuba@kernel.org>

bridge: Netlink interface fix.

This commit is correcting NETLINK br_fill_ifinfo() to be able to
handle 'filter_mask' with multiple flags asserted.

Fixes: 36a8e8e265420 ("bridge: Extend br_fill_ifinfo to return MPR status")

Signed-off-by: Henrik Bjoernlund <henrik.bjoernlund@microchip.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Suggested-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Merge tag 'drm-fixes-2020-10-08' of git://anongit.freedesktop.org/drm/drm

Pull drm nouveau fixes from Dave Airlie:
"Karol found two last minute nouveau fixes, they both fix crashes, the
  TTM one follows what other drivers do already, and the other is for
  bailing on load on unrecognised chipsets.

   - fix crash in TTM alloc fail path

   - return error earlier for unknown chipsets"

* tag 'drm-fixes-2020-10-08' of git://anongit.freedesktop.org/drm/drm:
  drm/nouveau/mem: guard against NULL pointer access in mem_del
  drm/nouveau/device: return error for unknown chipsets

Merge tag 'exfat-for-5.9-rc9' of git://git./linux/kernel/git/linkinjeon/exfat

Pull exfat fixes from Namjae Jeon:

- Fix use of uninitialized spinlock on error path

- Fix missing err assignment in exfat_build_inode()

* tag 'exfat-for-5.9-rc9' of git://git.kernel.org/pub/scm/linux/kernel/git/linkinjeon/exfat:
exfat: fix use of uninitialized spinlock on error path
exfat: fix pointer error checking

Merge tag 'for-linus-5.9b-rc9-tag' of git://git./linux/kernel/git/xen/tip

Pull xen fix from Juergen Gross:
"One fix for a regression when booting as a Xen guest on ARM64
  introduced probably during the 5.9 cycle. It is very low risk as it is
  modifying Xen specific code only.

  The exact commit introducing the bug hasn't been identified yet, but
  everything was fine in 5.8 and only in 5.9 some configurations started
  to fail"

* tag 'for-linus-5.9b-rc9-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
  arm/arm64: xen: Fix to convert percpu address to gfn correctly

afs: Fix deadlock between writeback and truncate

The afs filesystem has a lock[*] that it uses to serialise I/O operations
going to the server (vnode->io_lock), as the server will only perform one
modification operation at a time on any given file or directory.  This
prevents the the filesystem from filling up all the call slots to a server
with calls that aren't going to be executed in parallel anyway, thereby
allowing operations on other files to obtain slots.

  [*] Note that is probably redundant for directories at least since
      i_rwsem is used to serialise directory modifications and
      lookup/reading vs modification.  The server does allow parallel
      non-modification ops, however.

When a file truncation op completes, we truncate the in-memory copy of the
file to match - but we do it whilst still holding the io_lock, the idea
being to prevent races with other operations.

However, if writeback starts in a worker thread simultaneously with
truncation (whilst notify_change() is called with i_rwsem locked, writeback
pays it no heed), it may manage to set PG_writeback bits on the pages that
will get truncated before afs_setattr_success() manages to call
truncate_pagecache().  Truncate will then wait for those pages - whilst
still inside io_lock:

    # cat /proc/8837/stack
    [<0>] wait_on_page_bit_common+0x184/0x1e7
    [<0>] truncate_inode_pages_range+0x37f/0x3eb
    [<0>] truncate_pagecache+0x3c/0x53
    [<0>] afs_setattr_success+0x4d/0x6e
    [<0>] afs_wait_for_operation+0xd8/0x169
    [<0>] afs_do_sync_operation+0x16/0x1f
    [<0>] afs_setattr+0x1fb/0x25d
    [<0>] notify_change+0x2cf/0x3c4
    [<0>] do_truncate+0x7f/0xb2
    [<0>] do_sys_ftruncate+0xd1/0x104
    [<0>] do_syscall_64+0x2d/0x3a
    [<0>] entry_SYSCALL_64_after_hwframe+0x44/0xa9

The writeback operation, however, stalls indefinitely because it needs to
get the io_lock to proceed:

    # cat /proc/5940/stack
    [<0>] afs_get_io_locks+0x58/0x1ae
    [<0>] afs_begin_vnode_operation+0xc7/0xd1
    [<0>] afs_store_data+0x1b2/0x2a3
    [<0>] afs_write_back_from_locked_page+0x418/0x57c
    [<0>] afs_writepages_region+0x196/0x224
    [<0>] afs_writepages+0x74/0x156
    [<0>] do_writepages+0x2d/0x56
    [<0>] __writeback_single_inode+0x84/0x207
    [<0>] writeback_sb_inodes+0x238/0x3cf
    [<0>] __writeback_inodes_wb+0x68/0x9f
    [<0>] wb_writeback+0x145/0x26c
    [<0>] wb_do_writeback+0x16a/0x194
    [<0>] wb_workfn+0x74/0x177
    [<0>] process_one_work+0x174/0x264
    [<0>] worker_thread+0x117/0x1b9
    [<0>] kthread+0xec/0xf1
    [<0>] ret_from_fork+0x1f/0x30

and thus deadlock has occurred.

Note that whilst afs_setattr() calls filemap_write_and_wait(), the fact
that the caller is holding i_rwsem doesn't preclude more pages being
dirtied through an mmap'd region.

Fix this by:

(1) Use the vnode validate_lock to mediate access between afs_setattr()
     and afs_writepages():

     (a) Exclusively lock validate_lock in afs_setattr() around the whole
      RPC operation.

     (b) If WB_SYNC_ALL isn't set on entry to afs_writepages(), trying to
      shared-lock validate_lock and returning immediately if we couldn't
      get it.

     (c) If WB_SYNC_ALL is set, wait for the lock.

     The validate_lock is also used to validate a file and to zap its cache
     if the file was altered by a third party, so it's probably a good fit
     for this.

(2) Move the truncation outside of the io_lock in setattr, using the same
     hook as is used for local directory editing.

     This requires the old i_size to be retained in the operation record as
     we commit the revised status to the inode members inside the io_lock
     still, but we still need to know if we reduced the file size.

Fixes: d2ddc776a458 ("afs: Overhaul volume and server record caching and fileserver rotation")
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm: avoid early COW write protect games during fork()

In commit 70e806e4e645 ("mm: Do early cow for pinned pages during fork()
for ptes") we write-protected the PTE before doing the page pinning
check, in order to avoid a race with concurrent fast-GUP pinning (which
doesn't take the mm semaphore or the page table lock).

That trick doesn't actually work - it doesn't handle memory ordering
properly, and doing so would be prohibitively expensive.

It also isn't really needed.  While we're moving in the direction of
allowing and supporting page pinning without marking the pinned area
with MADV_DONTFORK, the fact is that we've never really supported this
kind of odd "concurrent fork() and page pinning", and doing the
serialization on a pte level is just wrong.

We can add serialization with a per-mm sequence counter, so we know how
to solve that race properly, but we'll do that at a more appropriate
time.  Right now this just removes the write protect games.

It also turns out that the write protect games actually break on Power,
as reported by Aneesh Kumar:

"Architecture like ppc64 expects set_pte_at to be not used for updating
  a valid pte. This is further explained in commit 56eecdb912b5 ("mm:
  Use ptep/pmdp_set_numa() for updating _PAGE_NUMA bit")"

and the code triggered a warning there:

  WARNING: CPU: 0 PID: 30613 at arch/powerpc/mm/pgtable.c:185 set_pte_at+0x2a8/0x3a0 arch/powerpc/mm/pgtable.c:185
  Call Trace:
    copy_present_page mm/memory.c:857 [inline]
    copy_present_pte mm/memory.c:899 [inline]
    copy_pte_range mm/memory.c:1014 [inline]
    copy_pmd_range mm/memory.c:1092 [inline]
    copy_pud_range mm/memory.c:1127 [inline]
    copy_p4d_range mm/memory.c:1150 [inline]
    copy_page_range+0x1f6c/0x2cc0 mm/memory.c:1212
    dup_mmap kernel/fork.c:592 [inline]
    dup_mm+0x77c/0xab0 kernel/fork.c:1355
    copy_mm kernel/fork.c:1411 [inline]
    copy_process+0x1f00/0x2740 kernel/fork.c:2070
    _do_fork+0xc4/0x10b0 kernel/fork.c:2429

Link: https://lore.kernel.org/lkml/CAHk-=wiWr+gO0Ro4LvnJBMs90OiePNyrE3E+pJvc9PzdBShdmw@mail.gmail.com/
Link: https://lore.kernel.org/linuxppc-dev/20201008092541.398079-1-aneesh.kumar@linux.ibm.com/
Reported-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Tested-by: Leon Romanovsky <leonro@nvidia.com>
Cc: Peter Xu <peterx@redhat.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: John Hubbard <jhubbard@nvidia.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Jan Kara <jack@suse.cz>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Kirill Shutemov <kirill@shutemov.name>
Cc: Hugh Dickins <hughd@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

net: wireless: nl80211: fix out-of-bounds access in nl80211_del_key()

In nl80211_parse_key(), key.idx is first initialized as -1.
If this value of key.idx remains unmodified and gets returned, and
nl80211_key_allowed() also returns 0, then rdev_del_key() gets called
with key.idx = -1.
This causes an out-of-bounds array access.

Handle this issue by checking if the value of key.idx after
nl80211_parse_key() is called and return -EINVAL if key.idx < 0.

Cc: stable@vger.kernel.org
Reported-by: syzbot+b1bb342d1d097516cbda@syzkaller.appspotmail.com
Tested-by: syzbot+b1bb342d1d097516cbda@syzkaller.appspotmail.com
Signed-off-by: Anant Thazhemadam <anant.thazhemadam@gmail.com>
Link: https://lore.kernel.org/r/20201007035401.9522-1-anant.thazhemadam@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

bpf: Fix scalar32_min_max_or bounds tracking

Simon reported an issue with the current scalar32_min_max_or() implementation.
That is, compared to the other 32 bit subreg tracking functions, the code in
scalar32_min_max_or() stands out that it's using the 64 bit registers instead
of 32 bit ones. This leads to bounds tracking issues, for example:

  [...]
  8: R0=map_value(id=0,off=0,ks=4,vs=48,imm=0) R10=fp0 fp-8=mmmmmmmm
  8: (79) r1 = *(u64 *)(r0 +0)
   R0=map_value(id=0,off=0,ks=4,vs=48,imm=0) R10=fp0 fp-8=mmmmmmmm
  9: R0=map_value(id=0,off=0,ks=4,vs=48,imm=0) R1_w=inv(id=0) R10=fp0 fp-8=mmmmmmmm
  9: (b7) r0 = 1
  10: R0_w=inv1 R1_w=inv(id=0) R10=fp0 fp-8=mmmmmmmm
  10: (18) r2 = 0x600000002
  12: R0_w=inv1 R1_w=inv(id=0) R2_w=inv25769803778 R10=fp0 fp-8=mmmmmmmm
  12: (ad) if r1 < r2 goto pc+1
   R0_w=inv1 R1_w=inv(id=0,umin_value=25769803778) R2_w=inv25769803778 R10=fp0 fp-8=mmmmmmmm
  13: R0_w=inv1 R1_w=inv(id=0,umin_value=25769803778) R2_w=inv25769803778 R10=fp0 fp-8=mmmmmmmm
  13: (95) exit
  14: R0_w=inv1 R1_w=inv(id=0,umax_value=25769803777,var_off=(0x0; 0x7ffffffff)) R2_w=inv25769803778 R10=fp0 fp-8=mmmmmmmm
  14: (25) if r1 > 0x0 goto pc+1
   R0_w=inv1 R1_w=inv(id=0,umax_value=0,var_off=(0x0; 0x7fffffff),u32_max_value=2147483647) R2_w=inv25769803778 R10=fp0 fp-8=mmmmmmmm
  15: R0_w=inv1 R1_w=inv(id=0,umax_value=0,var_off=(0x0; 0x7fffffff),u32_max_value=2147483647) R2_w=inv25769803778 R10=fp0 fp-8=mmmmmmmm
  15: (95) exit
  16: R0_w=inv1 R1_w=inv(id=0,umin_value=1,umax_value=25769803777,var_off=(0x0; 0x77fffffff),u32_max_value=2147483647) R2_w=inv25769803778 R10=fp0 fp-8=mmmmmmmm
  16: (47) r1 |= 0
  17: R0_w=inv1 R1_w=inv(id=0,umin_value=1,umax_value=32212254719,var_off=(0x1; 0x700000000),s32_max_value=1,u32_max_value=1) R2_w=inv25769803778 R10=fp0 fp-8=mmmmmmmm
  [...]

The bound tests on the map value force the upper unsigned bound to be 25769803777
in 64 bit (0b11000000000000000000000000000000001) and then lower one to be 1. By
using OR they are truncated and thus result in the range [1,1] for the 32 bit reg
tracker. This is incorrect given the only thing we know is that the value must be
positive and thus 2147483647 (0b1111111111111111111111111111111) at max for the
subregs. Fix it by using the {u,s}32_{min,max}_value vars instead. This also makes
sense, for example, for the case where we update dst_reg->s32_{min,max}_value in
the else branch we need to use the newly computed dst_reg->u32_{min,max}_value as
we know that these are positive. Previously, in the else branch the 64 bit values
of umin_value=1 and umax_value=32212254719 were used and latter got truncated to
be 1 as upper bound there. After the fix the subreg range is now correct:

  [...]
  8: R0=map_value(id=0,off=0,ks=4,vs=48,imm=0) R10=fp0 fp-8=mmmmmmmm
  8: (79) r1 = *(u64 *)(r0 +0)
   R0=map_value(id=0,off=0,ks=4,vs=48,imm=0) R10=fp0 fp-8=mmmmmmmm
  9: R0=map_value(id=0,off=0,ks=4,vs=48,imm=0) R1_w=inv(id=0) R10=fp0 fp-8=mmmmmmmm
  9: (b7) r0 = 1
  10: R0_w=inv1 R1_w=inv(id=0) R10=fp0 fp-8=mmmmmmmm
  10: (18) r2 = 0x600000002
  12: R0_w=inv1 R1_w=inv(id=0) R2_w=inv25769803778 R10=fp0 fp-8=mmmmmmmm
  12: (ad) if r1 < r2 goto pc+1
   R0_w=inv1 R1_w=inv(id=0,umin_value=25769803778) R2_w=inv25769803778 R10=fp0 fp-8=mmmmmmmm
  13: R0_w=inv1 R1_w=inv(id=0,umin_value=25769803778) R2_w=inv25769803778 R10=fp0 fp-8=mmmmmmmm
  13: (95) exit
  14: R0_w=inv1 R1_w=inv(id=0,umax_value=25769803777,var_off=(0x0; 0x7ffffffff)) R2_w=inv25769803778 R10=fp0 fp-8=mmmmmmmm
  14: (25) if r1 > 0x0 goto pc+1
   R0_w=inv1 R1_w=inv(id=0,umax_value=0,var_off=(0x0; 0x7fffffff),u32_max_value=2147483647) R2_w=inv25769803778 R10=fp0 fp-8=mmmmmmmm
  15: R0_w=inv1 R1_w=inv(id=0,umax_value=0,var_off=(0x0; 0x7fffffff),u32_max_value=2147483647) R2_w=inv25769803778 R10=fp0 fp-8=mmmmmmmm
  15: (95) exit
  16: R0_w=inv1 R1_w=inv(id=0,umin_value=1,umax_value=25769803777,var_off=(0x0; 0x77fffffff),u32_max_value=2147483647) R2_w=inv25769803778 R10=fp0 fp-8=mmmmmmmm
  16: (47) r1 |= 0
  17: R0_w=inv1 R1_w=inv(id=0,umin_value=1,umax_value=32212254719,var_off=(0x0; 0x77fffffff),u32_max_value=2147483647) R2_w=inv25769803778 R10=fp0 fp-8=mmmmmmmm
  [...]

Fixes: 3f50f132d840 ("bpf: Verifier, do explicit ALU32 bounds tracking")
Reported-by: Simon Scannell <scannell.smn@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>

drm/nouveau/mem: guard against NULL pointer access in mem_del

other drivers seems to do something similar

Signed-off-by: Karol Herbst <kherbst@redhat.com>
Cc: dri-devel <dri-devel@lists.freedesktop.org>
Cc: Dave Airlie <airlied@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201006220528.13925-2-kherbst@redhat.com

drm/nouveau/device: return error for unknown chipsets

Previously the code relied on device->pri to be NULL and to fail probing
later. We really should just return an error inside nvkm_device_ctor for
unsupported GPUs.

Fixes: 24d5ff40a732 ("drm/nouveau/device: rework mmio mapping code to get rid of second map")

Signed-off-by: Karol Herbst <kherbst@redhat.com>
Cc: dann frazier <dann.frazier@canonical.com>
Cc: dri-devel <dri-devel@lists.freedesktop.org>
Cc: Dave Airlie <airlied@redhat.com>
Cc: stable@vger.kernel.org
Reviewed-by: Jeremy Cline <jcline@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201006220528.13925-1-kherbst@redhat.com

exfat: fix use of uninitialized spinlock on error path

syzbot reported warning message:

Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x1d6/0x29e lib/dump_stack.c:118
register_lock_class+0xf06/0x1520 kernel/locking/lockdep.c:893
__lock_acquire+0xfd/0x2ae0 kernel/locking/lockdep.c:4320
lock_acquire+0x148/0x720 kernel/locking/lockdep.c:5029
__raw_spin_lock include/linux/spinlock_api_smp.h:142 [inline]
_raw_spin_lock+0x2a/0x40 kernel/locking/spinlock.c:151
spin_lock include/linux/spinlock.h:354 [inline]
exfat_cache_inval_inode+0x30/0x280 fs/exfat/cache.c:226
exfat_evict_inode+0x124/0x270 fs/exfat/inode.c:660
evict+0x2bb/0x6d0 fs/inode.c:576
exfat_fill_super+0x1e07/0x27d0 fs/exfat/super.c:681
get_tree_bdev+0x3e9/0x5f0 fs/super.c:1342
vfs_get_tree+0x88/0x270 fs/super.c:1547
do_new_mount fs/namespace.c:2875 [inline]
path_mount+0x179d/0x29e0 fs/namespace.c:3192
do_mount fs/namespace.c:3205 [inline]
__do_sys_mount fs/namespace.c:3413 [inline]
__se_sys_mount+0x126/0x180 fs/namespace.c:3390
do_syscall_64+0x31/0x70 arch/x86/entry/common.c:46
entry_SYSCALL_64_after_hwframe+0x44/0xa9

If exfat_read_root() returns an error, spinlock is used in
exfat_evict_inode() without initialization. This patch combines
exfat_cache_init_inode() with exfat_inode_init_once() to initialize
spinlock by slab constructor.

Fixes: c35b6810c495 ("exfat: add exfat cache")
Cc: stable@vger.kernel.org # v5.7+
Reported-by: syzbot <syzbot+b91107320911a26c9a95@syzkaller.appspotmail.com>
Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com>

exfat: fix pointer error checking

Fix missing result check of exfat_build_inode().
And use PTR_ERR_OR_ZERO instead of PTR_ERR.

Signed-off-by: Tetsuhiro Kohada <kohada.t2@gmail.com>
Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com>

arm/arm64: xen: Fix to convert percpu address to gfn correctly

Use per_cpu_ptr_to_phys() instead of virt_to_phys() for per-cpu
address conversion.

In xen_starting_cpu(), per-cpu xen_vcpu_info address is converted
to gfn by virt_to_gfn() macro. However, since the virt_to_gfn(v)
assumes the given virtual address is in linear mapped kernel memory
area, it can not convert the per-cpu memory if it is allocated on
vmalloc area.

This depends on CONFIG_NEED_PER_CPU_EMBED_FIRST_CHUNK.
If it is enabled, the first chunk of percpu memory is linear mapped.
In the other case, that is allocated from vmalloc area. Moreover,
if the first chunk of percpu has run out until allocating
xen_vcpu_info, it will be allocated on the 2nd chunk, which is
based on kernel memory or vmalloc memory (depends on
CONFIG_NEED_PER_CPU_KM).

Without this fix and kernel configured to use vmalloc area for
the percpu memory, the Dom0 kernel will fail to boot with following
errors.

[    0.466172] Xen: initializing cpu0
[    0.469601] ------------[ cut here ]------------
[    0.474295] WARNING: CPU: 0 PID: 1 at arch/arm64/xen/../../arm/xen/enlighten.c:153 xen_starting_cpu+0x160/0x180
[    0.484435] Modules linked in:
[    0.487565] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 5.9.0-rc4+ #4
[    0.493895] Hardware name: Socionext Developer Box (DT)
[    0.499194] pstate: 00000005 (nzcv daif -PAN -UAO BTYPE=--)
[    0.504836] pc : xen_starting_cpu+0x160/0x180
[    0.509263] lr : xen_starting_cpu+0xb0/0x180
[    0.513599] sp : ffff8000116cbb60
[    0.516984] x29: ffff8000116cbb60 x28: ffff80000abec000
[    0.522366] x27: 0000000000000000 x26: 0000000000000000
[    0.527754] x25: ffff80001156c000 x24: fffffdffbfcdb600
[    0.533129] x23: 0000000000000000 x22: 0000000000000000
[    0.538511] x21: ffff8000113a99c8 x20: ffff800010fe4f68
[    0.543892] x19: ffff8000113a9988 x18: 0000000000000010
[    0.549274] x17: 0000000094fe0f81 x16: 00000000deadbeef
[    0.554655] x15: ffffffffffffffff x14: 0720072007200720
[    0.560037] x13: 0720072007200720 x12: 0720072007200720
[    0.565418] x11: 0720072007200720 x10: 0720072007200720
[    0.570801] x9 : ffff8000100fbdc0 x8 : ffff800010715208
[    0.576182] x7 : 0000000000000054 x6 : ffff00001b790f00
[    0.581564] x5 : ffff800010bbf880 x4 : 0000000000000000
[    0.586945] x3 : 0000000000000000 x2 : ffff80000abec000
[    0.592327] x1 : 000000000000002f x0 : 0000800000000000
[    0.597716] Call trace:
[    0.600232]  xen_starting_cpu+0x160/0x180
[    0.604309]  cpuhp_invoke_callback+0xac/0x640
[    0.608736]  cpuhp_issue_call+0xf4/0x150
[    0.612728]  __cpuhp_setup_state_cpuslocked+0x128/0x2c8
[    0.618030]  __cpuhp_setup_state+0x84/0xf8
[    0.622192]  xen_guest_init+0x324/0x364
[    0.626097]  do_one_initcall+0x54/0x250
[    0.630003]  kernel_init_freeable+0x12c/0x2c8
[    0.634428]  kernel_init+0x1c/0x128
[    0.637988]  ret_from_fork+0x10/0x18
[    0.641635] ---[ end trace d95b5309a33f8b27 ]---
[    0.646337] ------------[ cut here ]------------
[    0.651005] kernel BUG at arch/arm64/xen/../../arm/xen/enlighten.c:158!
[    0.657697] Internal error: Oops - BUG: 0 [#1] SMP
[    0.662548] Modules linked in:
[    0.665676] CPU: 0 PID: 1 Comm: swapper/0 Tainted: G        W         5.9.0-rc4+ #4
[    0.673398] Hardware name: Socionext Developer Box (DT)
[    0.678695] pstate: 00000005 (nzcv daif -PAN -UAO BTYPE=--)
[    0.684338] pc : xen_starting_cpu+0x178/0x180
[    0.688765] lr : xen_starting_cpu+0x144/0x180
[    0.693188] sp : ffff8000116cbb60
[    0.696573] x29: ffff8000116cbb60 x28: ffff80000abec000
[    0.701955] x27: 0000000000000000 x26: 0000000000000000
[    0.707344] x25: ffff80001156c000 x24: fffffdffbfcdb600
[    0.712718] x23: 0000000000000000 x22: 0000000000000000
[    0.718107] x21: ffff8000113a99c8 x20: ffff800010fe4f68
[    0.723481] x19: ffff8000113a9988 x18: 0000000000000010
[    0.728863] x17: 0000000094fe0f81 x16: 00000000deadbeef
[    0.734245] x15: ffffffffffffffff x14: 0720072007200720
[    0.739626] x13: 0720072007200720 x12: 0720072007200720
[    0.745008] x11: 0720072007200720 x10: 0720072007200720
[    0.750390] x9 : ffff8000100fbdc0 x8 : ffff800010715208
[    0.755771] x7 : 0000000000000054 x6 : ffff00001b790f00
[    0.761153] x5 : ffff800010bbf880 x4 : 0000000000000000
[    0.766534] x3 : 0000000000000000 x2 : 00000000deadbeef
[    0.771916] x1 : 00000000deadbeef x0 : ffffffffffffffea
[    0.777304] Call trace:
[    0.779819]  xen_starting_cpu+0x178/0x180
[    0.783898]  cpuhp_invoke_callback+0xac/0x640
[    0.788325]  cpuhp_issue_call+0xf4/0x150
[    0.792317]  __cpuhp_setup_state_cpuslocked+0x128/0x2c8
[    0.797619]  __cpuhp_setup_state+0x84/0xf8
[    0.801779]  xen_guest_init+0x324/0x364
[    0.805683]  do_one_initcall+0x54/0x250
[    0.809590]  kernel_init_freeable+0x12c/0x2c8
[    0.814016]  kernel_init+0x1c/0x128
[    0.817583]  ret_from_fork+0x10/0x18
[    0.821226] Code: d0006980 f9427c00 cb000300 17ffffea (d4210000)
[    0.827415] ---[ end trace d95b5309a33f8b28 ]---
[    0.832076] Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000000b
[    0.839815] ---[ end Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000000b ]---

Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
Link: https://lore.kernel.org/r/160196697165.60224.17470743378683334995.stgit@devnote2
Signed-off-by: Juergen Gross <jgross@suse.com>

Merge tag 'arm64-fixes' of git://git./linux/kernel/git/arm64/linux

Pull arm64 fix from Catalin Marinas:
"Fix a kernel panic in the AES crypto code caused by a BR tail call not
  matching the target BTI instruction (when branch target identification
  is enabled)"

* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
  crypto: arm64: Use x16 with indirect branch to bti_c

Merge tag 'platform-drivers-x86-v5.9-3' of git://git./linux/kernel/git/pdx86/platform-drivers-x86

Pull another x86 platform driver fix from Hans de Goede:
"One final pdx86 fix for Tablet Mode reporting regressions (which make
  the keyboard and touchpad unusable) on various Asus notebooks.

  These regressions were caused by the asus-nb-wmi and the intel-vbtn
  drivers both receiving recent patches to start reporting Tablet Mode /
  to report it on more models.

  Due to a miscommunication between Andy and me, Andy's earlier pull-req
  only contained the fix for the intel-vbtn driver and not the fix for
  the asus-nb-wmi code.

  This fix has been tested as a downstream patch in Fedora kernels for
  approx two weeks with no problems being reported"

* tag 'platform-drivers-x86-v5.9-3' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86:
  platform/x86: asus-wmi: Fix SW_TABLET_MODE always reporting 1 on many different models

Merge tag 'drm-fixes-2020-10-06-1' of git://anongit.freedesktop.org/drm/drm

Pull drm fixes from Dave Airlie:
"Daniel queued these up last week and I took a long weekend so didn't
  get them out, but fixing the OOB access on get font seems like
  something we should land and it's cc'ed stable as well.

  The other big change is a partial revert for a regression on android
  on the clcd fbdev driver, and one other docs fix.

  fbdev:
   - Re-add FB_ARMCLCD for android
   - Fix global-out-of-bounds read in fbcon_get_font()

  core:
   - Small doc fix"

* tag 'drm-fixes-2020-10-06-1' of git://anongit.freedesktop.org/drm/drm:
  drm: drm_dsc.h: fix a kernel-doc markup
  Partially revert "video: fbdev: amba-clcd: Retire elder CLCD driver"
  fbcon: Fix global-out-of-bounds read in fbcon_get_font()
  Fonts: Support FONT_EXTRA_WORDS macros for built-in fonts
  fbdev, newport_con: Move FONT_EXTRA_WORDS macros into linux/font.h

usermodehelper: reset umask to default before executing user process

Kernel threads intentionally do CLONE_FS in order to follow any changes
that 'init' does to set up the root directory (or cwd).

It is admittedly a bit odd, but it avoids the situation where 'init'
does some extensive setup to initialize the system environment, and then
we execute a usermode helper program, and it uses the original FS setup
from boot time that may be very limited and incomplete.

[ Both Al Viro and Eric Biederman point out that 'pivot_root()' will
  follow the root regardless, since it fixes up other users of root (see
  chroot_fs_refs() for details), but overmounting root and doing a
  chroot() would not. ]

However, Vegard Nossum noticed that the CLONE_FS not only means that we
follow the root and current working directories, it also means we share
umask with whatever init changed it to. That wasn't intentional.

Just reset umask to the original default (0022) before actually starting
the usermode helper program.

Reported-by: Vegard Nossum <vegard.nossum@oracle.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Acked-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

splice: teach splice pipe reading about empty pipe buffers

Tetsuo Handa reports that splice() can return 0 before the real EOF, if
the data in the splice source pipe is an empty pipe buffer.  That empty
pipe buffer case doesn't happen in any normal situation, but you can
trigger it by doing a write to a pipe that fails due to a page fault.

Tetsuo has a test-case to show the behavior:

  #define _GNU_SOURCE
  #include <sys/types.h>
  #include <sys/stat.h>
  #include <fcntl.h>
  #include <unistd.h>

  int main(int argc, char *argv[])
  {
const int fd = open("/tmp/testfile", O_WRONLY | O_CREAT, 0600);
int pipe_fd[2] = { -1, -1 };
pipe(pipe_fd);
write(pipe_fd[1], NULL, 4096);
/* This splice() should wait unless interrupted. */
return !splice(pipe_fd[0], NULL, fd, NULL, 65536, 0);
  }

which results in

    write(5, NULL, 4096)                    = -1 EFAULT (Bad address)
    splice(4, NULL, 3, NULL, 65536, 0)      = 0

and this can confuse splice() users into believing they have hit EOF
prematurely.

The issue was introduced when the pipe write code started pre-allocating
the pipe buffers before copying data from user space.

This is modified verion of Tetsuo's original patch.

Fixes: a194dfe6e6f6 ("pipe: Rearrange sequence in pipe_write() to preallocate slot")
Link:https://lore.kernel.org/linux-fsdevel/20201005121339.4063-1-penguin-kernel@I-love.SAKURA.ne.jp/
Reported-by: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp>
Acked-by: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

crypto: arm64: Use x16 with indirect branch to bti_c

The AES code uses a 'br x7' as part of a function called by
a macro. That branch needs a bti_j as a target. This results
in a panic as seen below. Using x16 (or x17) with an indirect
branch keeps the target bti_c.

  Bad mode in Synchronous Abort handler detected on CPU1, code 0x34000003 -- BTI
  CPU: 1 PID: 265 Comm: cryptomgr_test Not tainted 5.8.11-300.fc33.aarch64 #1
  pstate: 20400c05 (nzCv daif +PAN -UAO BTYPE=j-)
  pc : aesbs_encrypt8+0x0/0x5f0 [aes_neon_bs]
  lr : aesbs_xts_encrypt+0x48/0xe0 [aes_neon_bs]
  sp : ffff80001052b730

  aesbs_encrypt8+0x0/0x5f0 [aes_neon_bs]
   __xts_crypt+0xb0/0x2dc [aes_neon_bs]
   xts_encrypt+0x28/0x3c [aes_neon_bs]
  crypto_skcipher_encrypt+0x50/0x84
  simd_skcipher_encrypt+0xc8/0xe0
  crypto_skcipher_encrypt+0x50/0x84
  test_skcipher_vec_cfg+0x224/0x5f0
  test_skcipher+0xbc/0x120
  alg_test_skcipher+0xa0/0x1b0
  alg_test+0x3dc/0x47c
  cryptomgr_test+0x38/0x60

Fixes: 0e89640b640d ("crypto: arm64 - Use modern annotations for assembly functions")
Cc: <stable@vger.kernel.org> # 5.6.x-
Signed-off-by: Jeremy Linton <jeremy.linton@arm.com>
Suggested-by: Dave P Martin <Dave.Martin@arm.com>
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20201006163326.2780619-1-jeremy.linton@arm.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>

Merge branch 'ethtool-allow-dumping-policies-to-user-space'

Jakub Kicinski says:

====================
ethtool: allow dumping policies to user space

This series wires up ethtool policies to ops, so they can be
dumped to user space for feature discovery.

First patch wires up GET commands, and second patch wires up SETs.

The policy tables are trimmed to save space and LoC.

Next - take care of linking up nested policies for the header
(which is the policy what we actually care about). And once header
policy is linked make sure that attribute range validation for flags
is done by policy, not a conditions in the code. New type of policy
is needed to validate masks (patch 6).

Netlink as always staying a step ahead of all the other kernel
API interfaces :)

v2:
- merge patches 1 & 2 -> 1
- add patch 3 & 5
- remove .max_attr from struct ethnl_request_ops
====================

Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

ethtool: specify which header flags are supported per command

Perform header flags validation through the policy.

Only pause command supports ETHTOOL_FLAG_STATS. Create a separate
policy to be able to express that in policy dumps to user space.

Note that even though the core will validate the header policy,
it cannot record multiple layers of attributes and we have to
re-parse header sub-attrs. When doing so we could skip attribute
validation, or use most permissive policy. Opt for the former.

We will no longer return the extack cookie for flags but since
we only added first new flag in this release it's not expected
that any user space had a chance to make use of it.

v2: - remove the re-validation in ethnl_parse_header_dev_get()

Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

netlink: add mask validation

We don't have good validation policy for existing unsigned int attrs
which serve as flags (for new ones we could use NLA_BITFIELD32).
With increased use of policy dumping having the validation be
expressed as part of the policy is important. Add validation
policy in form of a mask of supported/valid bits.

Support u64 in the uAPI to be future-proof, but really for now
the embedded mask member can only hold 32 bits, so anything with
bit 32+ set will always fail validation.

Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

netlink: create helpers for checking type is an int

There's a number of policies which check if type is a uint or sint.
Factor the checking against the list of value sizes to a helper
for easier reuse.

v2: - new patch

Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

ethtool: link up ethnl_header_policy as a nested policy

To get the most out of parsing by the core, and to allow dumping
full policies we need to specify which policy applies to nested
attrs. For headers it's ethnl_header_policy.

$ sed -i 's@$ETHTOOL_A_.*HEADER\].*=$ { .type = NLA_NESTED },@\1\n\t\tNLA_POLICY_NESTED(ethnl_header_policy),@' net/ethtool/*

Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

ethtool: trim policy tables

Since ethtool uses strict attribute validation there's no need
to initialize all attributes in policy tables. 0 is NLA_UNSPEC
which is going to be rejected. Remove the NLA_REJECTs.

Similarly attributes above maxattrs are rejected, so there's
no need to always size the policy tables to ETHTOOL_A_..._MAX.

v2: - new patch

Suggested-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

ethtool: wire up set policies to ops

Similarly to get commands wire up the policies of set commands
to get parsing by the core and policy dumps.

Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

ethtool: wire up get policies to ops

Wire up policies for get commands in struct nla_policy of the ethtool
family. Make use of genetlink code attr validation and parsing, as well
as allow dumping policies to user space.

For every ETHTOOL_MSG_*_GET:
- add 'ethnl_' prefix to policy name
- add extern declaration in net/ethtool/netlink.h
- wire up the policy & attr in ethtool_genl_ops[].
- remove .request_policy and .max_attr from ethnl_request_ops.

Obviously core only records the first "layer" of parsed attrs
so we still need to parse the sub-attrs of the nested header
attribute.

v2:
- merge of patches 1 and 2 from v1
- remove stray empty lines in ops
- also remove .max_attr

Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'drivers-net-add-sw_netstats_rx_add-helper'

Fabian Frederick says:

====================
drivers/net: add sw_netstats_rx_add helper

This small patchset creates netstats addition dev_sw_netstats_rx_add()
based on dev_lstats_add() and replaces some open coding
in both drivers/net and net branches.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

ipv4: use dev_sw_netstats_rx_add()

use new helper for netstats settings

Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: openvswitch: use dev_sw_netstats_rx_add()

use new helper for netstats settings

Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: David S. Miller <davem@davemloft.net>

xfrm: use dev_sw_netstats_rx_add()

use new helper for netstats settings

Signed-off-by: Fabian Frederick <fabf@skynet.be>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

ipv6: use dev_sw_netstats_rx_add()

use new helper for netstats settings

Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: David S. Miller <davem@davemloft.net>

gtp: use dev_sw_netstats_rx_add()

use new helper for netstats settings

Signed-off-by: Fabian Frederick <fabf@skynet.be>
Acked-by: Harald Welte <laforge@gnumonks.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

bareudp: use dev_sw_netstats_rx_add()

use new helper for netstats settings

Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: David S. Miller <davem@davemloft.net>

geneve: use dev_sw_netstats_rx_add()

use new helper for netstats settings

Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: David S. Miller <davem@davemloft.net>

vxlan: use dev_sw_netstats_rx_add()

use new helper for netstats settings

Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: netdevice.h: sw_netstats_rx_add helper

some drivers/network protocols update rx bytes/packets under
u64_stats_update_begin/end sequence.
Add a specific helper like dev_lstats_add()

Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'rxrpc-fixes-20201005' of git://git./linux/kernel/git/dhowells/linux-fs

David Howells says:

====================
rxrpc: Miscellaneous fixes

Here are some miscellaneous rxrpc fixes:

(1) Fix the xdr encoding of the contents read from an rxrpc key.

(2) Fix a BUG() for a unsupported encoding type.

(3) Fix missing _bh lock annotations.

(4) Fix acceptance handling for an incoming call where the incoming call
     is encrypted.

(5) The server token keyring isn't network namespaced - it belongs to the
     server, so there's no need.  Namespacing it means that request_key()
     fails to find it.

(6) Fix a leak of the server keyring.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'net-atlantic-phy-tunables-from-mac-driver'

Igor Russkikh says:

====================
net: atlantic: phy tunables from mac driver

This series implements phy tunables settings via MAC driver callbacks.

AQC 10G devices use integrated MAC+PHY solution, where PHY is fully controlled
by MAC firmware. Therefore, it is not possible to implement separate phy driver
for these.

We use ethtool ops callbacks to implement downshift and EDPC tunables.

v3: fixed flaw in EDPD logic, from Andrew
v2: comments from Andrew
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

net: atlantic: implement media detect feature via phy tunables

Mediadetect is another name for the EDPD (energy detect power down).
This feature allows device to save extra power when no link is available.

PHY goes into the extreme power saving mode and only periodically wakes up
and checks for the link.

AQC devices has fixed check period of 6 seconds

The feature may increase linkup time.

Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: atlantic: implement phy downshift feature

PHY downshift allows phy to try renegotiate if link is unstable
and can carry higher speed.

AQC devices has integrated PHY which is controlled by MAC firmware.
Thus, driver defines new ethtool callbacks to implement phy tunables
via netdev.

Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ethtool: allow netdev driver to define phy tunables

Define get/set phy tunable callbacks in ethtool ops.
This will allow MAC drivers with integrated PHY still to implement
these tunables.

Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: always dump full packets with skb_dump

Currently skb_dump has a restriction to only dump full packet for the
first 5 socket buffers, then only headers will be printed. Remove this
arbitrary and confusing restriction, which is only documented vaguely
("up to") in the comments above the prototype.

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tcp: fix receive window update in tcp_add_backlog()

We got reports from GKE customers flows being reset by netfilter
conntrack unless nf_conntrack_tcp_be_liberal is set to 1.

Traces seemed to suggest ACK packet being dropped by the
packet capture, or more likely that ACK were received in the
wrong order.

wscale=7, SYN and SYNACK not shown here.

This ACK allows the sender to send 1871*128 bytes from seq 51359321 :
New right edge of the window -> 51359321+1871*128=51598809

09:17:23.389210 IP A > B: Flags [.], ack 51359321, win 1871, options [nop,nop,TS val 10 ecr 999], length 0

09:17:23.389212 IP B > A: Flags [.], seq 51422681:51424089, ack 1577, win 268, options [nop,nop,TS val 999 ecr 10], length 1408
09:17:23.389214 IP A > B: Flags [.], ack 51422681, win 1376, options [nop,nop,TS val 10 ecr 999], length 0
09:17:23.389253 IP B > A: Flags [.], seq 51424089:51488857, ack 1577, win 268, options [nop,nop,TS val 999 ecr 10], length 64768
09:17:23.389272 IP A > B: Flags [.], ack 51488857, win 859, options [nop,nop,TS val 10 ecr 999], length 0
09:17:23.389275 IP B > A: Flags [.], seq 51488857:51521241, ack 1577, win 268, options [nop,nop,TS val 999 ecr 10], length 32384

Receiver now allows to send 606*128=77568 from seq 51521241 :
New right edge of the window -> 51521241+606*128=51598809

09:17:23.389296 IP A > B: Flags [.], ack 51521241, win 606, options [nop,nop,TS val 10 ecr 999], length 0

09:17:23.389308 IP B > A: Flags [.], seq 51521241:51553625, ack 1577, win 268, options [nop,nop,TS val 999 ecr 10], length 32384

It seems the sender exceeds RWIN allowance, since 51611353 > 51598809

09:17:23.389346 IP B > A: Flags [.], seq 51553625:51611353, ack 1577, win 268, options [nop,nop,TS val 999 ecr 10], length 57728
09:17:23.389356 IP B > A: Flags [.], seq 51611353:51618393, ack 1577, win 268, options [nop,nop,TS val 999 ecr 10], length 7040

09:17:23.389367 IP A > B: Flags [.], ack 51611353, win 0, options [nop,nop,TS val 10 ecr 999], length 0

netfilter conntrack is not happy and sends RST

09:17:23.389389 IP A > B: Flags [R], seq 92176528, win 0, length 0
09:17:23.389488 IP B > A: Flags [R], seq 174478967, win 0, length 0

Now imagine ACK were delivered out of order and tcp_add_backlog() sets window based on wrong packet.
New right edge of the window -> 51521241+859*128=51631193

Normally TCP stack handles OOO packets just fine, but it
turns out tcp_add_backlog() does not. It can update the window
field of the aggregated packet even if the ACK sequence
of the last received packet is too old.

Many thanks to Alexandre Ferrieux for independently reporting the issue
and suggesting a fix.

Fixes: 4f693b55c3d2 ("tcp: implement coalescing on backlog queue")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Alexandre Ferrieux <alexandre.ferrieux@orange.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: usb: rtl8150: set random MAC address when set_ethernet_addr() fails

When get_registers() fails in set_ethernet_addr(),the uninitialized
value of node_id gets copied over as the address.
So, check the return value of get_registers().

If get_registers() executed successfully (i.e., it returns
sizeof(node_id)), copy over the MAC address using ether_addr_copy()
(instead of using memcpy()).

Else, if get_registers() failed instead, a randomly generated MAC
address is set as the MAC address instead.

Reported-by: syzbot+abbc768b560c84d92fd3@syzkaller.appspotmail.com
Tested-by: syzbot+abbc768b560c84d92fd3@syzkaller.appspotmail.com
Acked-by: Petko Manolov <petkan@nucleusys.com>
Signed-off-by: Anant Thazhemadam <anant.thazhemadam@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

mptcp: don't skip needed ack

Currently we skip calling tcp_cleanup_rbuf() when packets
are moved into the OoO queue or simply dropped. In both
cases we still increment tp->copied_seq, and we should
ask the TCP stack to check for ack.

Fixes: c76c6956566f ("mptcp: call tcp_cleanup_rbuf on subflows")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

mptcp: more DATA FIN fixes

Currently data fin on data packet are not handled properly:
the 'rcv_data_fin_seq' field is interpreted as the last
sequence number carrying a valid data, but for data fin
packet with valid maps we currently store map_seq + map_len,
that is, the next value.

The 'write_seq' fields carries instead the value subseguent
to the last valid byte, so in mptcp_write_data_fin() we
never detect correctly the last DSS map.

Fixes: 7279da6145bb ("mptcp: Use MPTCP-level flag for sending DATA_FIN")
Fixes: 1a49b2c2a501 ("mptcp: Handle incoming 32-bit DATA_FIN values")
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'Fix-tail-dropping-watermarks-for-Ocelot-switches'

Vladimir Oltean says:

====================
Fix tail dropping watermarks for Ocelot switches

This series adds a missing division by 60, and a warning to prevent that
in the future.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

net: mscc: ocelot: warn when encoding an out-of-bounds watermark value

There is an upper bound to the value that a watermark may hold. That
upper bound is not immediately obvious during configuration, and it
might be possible to have accidental truncation.

Actually this has happened already, add a warning to prevent it from
happening again.

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: mscc: ocelot: divide watermark value by 60 when writing to SYS_ATOP

Tail dropping is enabled for a port when:

1. A source port consumes more packet buffers than the watermark encoded
in SYS:PORT:ATOP_CFG.ATOP.

AND

2. Total memory use exceeds the consumption watermark encoded in
SYS:PAUSE_CFG:ATOP_TOT_CFG.

The unit of these watermarks is a 60 byte memory cell. That unit is
programmed properly into ATOP_TOT_CFG, but not into ATOP. Actually when
written into ATOP, it would get truncated and wrap around.

Fixes: a556c76adc05 ("net: mscc: Add initial Ocelot switch support")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: qrtr: ns: Fix the incorrect usage of rcu_read_lock()

The rcu_read_lock() is not supposed to lock the kernel_sendmsg() API
since it has the lock_sock() in qrtr_sendmsg() which will sleep. Hence,
fix it by excluding the locking for kernel_sendmsg().

While at it, let's also use radix_tree_deref_retry() to confirm the
validity of the pointer returned by radix_tree_deref_slot() and use
radix_tree_iter_resume() to resume iterating the tree properly before
releasing the lock as suggested by Doug.

Fixes: a7809ff90ce6 ("net: qrtr: ns: Protect radix_tree_deref_slot() using rcu read locks")
Reported-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Alex Elder <elder@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

platform/x86: asus-wmi: Fix SW_TABLET_MODE always reporting 1 on many different models

Commit b0dbd97de1f1 ("platform/x86: asus-wmi: Add support for
SW_TABLET_MODE") added support for reporting SW_TABLET_MODE using the
Asus 0x00120063 WMI-device-id to see if various transformer models were
docked into their keyboard-dock (SW_TABLET_MODE=0) or if they were
being used as a tablet.

The new SW_TABLET_MODE support (naively?) assumed that non Transformer
devices would either not support the 0x00120063 WMI-device-id at all,
or would NOT set ASUS_WMI_DSTS_PRESENCE_BIT in their reply when querying
the device-id.

Unfortunately this is not true and we have received many bug reports about
this change causing the asus-wmi driver to always report SW_TABLET_MODE=1
on non Transformer devices. This causes libinput to think that these are
360 degree hinges style 2-in-1s folded into tablet-mode. Making libinput
suppress keyboard and touchpad events from the builtin keyboard and
touchpad. So effectively this causes the keyboard and touchpad to not work
on many non Transformer Asus models.

This commit fixes this by using the existing DMI based quirk mechanism in
asus-nb-wmi.c to allow using the 0x00120063 device-id for reporting
SW_TABLET_MODE on Transformer models and ignoring it on all other models.

Fixes: b0dbd97de1f1 ("platform/x86: asus-wmi: Add support for SW_TABLET_MODE")
Link: https://patchwork.kernel.org/patch/11780901/
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=209011
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1876997
Reported-by: Samuel Čavoj <samuel@cavoj.net>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>

Merge tag 'drm-misc-fixes-2020-10-01' of git://anongit.freedesktop.org/drm/drm-misc into drm-fixes

drm-misc-fixes for v5.9:
- Small doc fix.
- Re-add FB_ARMCLCD for android.
- Fix global-out-of-bounds read in fbcon_get_font().

Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/8585daa2-fcbc-3924-ac4f-e7b5668808e0@linux.intel.com

Merge git://git./linux/kernel/git/netdev/net

Rejecting non-native endian BTF overlapped with the addition
of support for it.

The rest were more simple overlapping changes, except the
renesas ravb binding update, which had to follow a file
move as well as a YAML conversion.

Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'platform-drivers-x86-v5.9-2' of git://git.infradead.org/linux-platform-drivers-x86

Pull x86 platform driver fixes from Andy Shevchenko:
"We have some fixes for Tablet Mode reporting in particular, that users
  are complaining a lot about.

  Summary:

   - Attempt #3 of enabling Tablet Mode reporting w/o regressions

   - Improve battery recognition code in ASUS WMI driver

   - Fix Kconfig dependency warning for Fujitsu and LG laptop drivers

   - Add fixes in Thinkpad ACPI driver for _BCL method and NVRAM polling

   - Fix power supply extended topology in Mellanox driver

   - Fix memory leak in OLPC EC driver

   - Avoid static struct device in Intel PMC core driver

   - Add support for the touchscreen found in MPMAN Converter9 2-in-1

   - Update MAINTAINERS to reflect the real state of affairs"

* tag 'platform-drivers-x86-v5.9-2' of git://git.infradead.org/linux-platform-drivers-x86:
  platform/x86: thinkpad_acpi: re-initialize ACPI buffer size when reuse
  MAINTAINERS: Add Mark Gross and Hans de Goede as x86 platform drivers maintainers
  platform/x86: intel-vbtn: Switch to an allow-list for SW_TABLET_MODE reporting
  platform/x86: intel-vbtn: Revert "Fix SW_TABLET_MODE always reporting 1 on the HP Pavilion 11 x360"
  platform/x86: intel_pmc_core: do not create a static struct device
  platform/x86: mlx-platform: Fix extended topology configuration for power supply units
  platform/x86: pcengines-apuv2: Fix typo on define of AMD_FCH_GPIO_REG_GPIO55_DEVSLP0
  platform/x86: fix kconfig dependency warning for FUJITSU_LAPTOP
  platform/x86: fix kconfig dependency warning for LG_LAPTOP
  platform/x86: thinkpad_acpi: initialize tp_nvram_state variable
  platform/x86: intel-vbtn: Fix SW_TABLET_MODE always reporting 1 on the HP Pavilion 11 x360
  platform/x86: asus-wmi: Add BATC battery name to the list of supported
  platform/x86: asus-nb-wmi: Revert "Do not load on Asus T100TA and T200TA"
  platform/x86: touchscreen_dmi: Add info for the MPMAN Converter9 2-in-1
  Documentation: laptops: thinkpad-acpi: fix underline length build warning
  Platform: OLPC: Fix memleak in olpc_ec_probe

Merge git://git./linux/kernel/git/netdev/net

Pull networking fixes from David Miller:

1) Make sure SKB control block is in the proper state during IPSEC
    ESP-in-TCP encapsulation. From Sabrina Dubroca.

2) Various kinds of attributes were not being cloned properly when we
    build new xfrm_state objects from existing ones. Fix from Antony
    Antony.

3) Make sure to keep BTF sections, from Tony Ambardar.

4) TX DMA channels need proper locking in lantiq driver, from Hauke
    Mehrtens.

5) Honour route MTU during forwarding, always. From Maciej
    Żenczykowski.

6) Fix races in kTLS which can result in crashes, from Rohit
    Maheshwari.

7) Skip TCP DSACKs with rediculous sequence ranges, from Priyaranjan
    Jha.

8) Use correct address family in xfrm state lookups, from Herbert Xu.

9) A bridge FDB flush should not clear out user managed fdb entries
    with the ext_learn flag set, from Nikolay Aleksandrov.

10) Fix nested locking of netdev address lists, from Taehee Yoo.

11) Fix handling of 32-bit DATA_FIN values in mptcp, from Mat Martineau.

12) Fix r8169 data corruptions on RTL8402 chips, from Heiner Kallweit.

13) Don't free command entries in mlx5 while comp handler could still be
    running, from Eran Ben Elisha.

14) Error flow of request_irq() in mlx5 is busted, due to an off by one
    we try to free and IRQ never allocated. From Maor Gottlieb.

15) Fix leak when dumping netlink policies, from Johannes Berg.

16) Sendpage cannot be performed when a page is a slab page, or the page
    count is < 1. Some subsystems such as nvme were doing so. Create a
    "sendpage_ok()" helper and use it as needed, from Coly Li.

17) Don't leak request socket when using syncookes with mptcp, from
    Paolo Abeni.

* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (111 commits)
  net/core: check length before updating Ethertype in skb_mpls_{push,pop}
  net: mvneta: fix double free of txq->buf
  net_sched: check error pointer in tcf_dump_walker()
  net: team: fix memory leak in __team_options_register
  net: typhoon: Fix a typo Typoon --> Typhoon
  net: hinic: fix DEVLINK build errors
  net: stmmac: Modify configuration method of EEE timers
  tcp: fix syn cookied MPTCP request socket leak
  libceph: use sendpage_ok() in ceph_tcp_sendpage()
  scsi: libiscsi: use sendpage_ok() in iscsi_tcp_segment_map()
  drbd: code cleanup by using sendpage_ok() to check page for kernel_sendpage()
  tcp: use sendpage_ok() to detect misused .sendpage
  nvme-tcp: check page by sendpage_ok() before calling kernel_sendpage()
  net: add WARN_ONCE in kernel_sendpage() for improper zero-copy send
  net: introduce helper sendpage_ok() in include/linux/net.h
  net: usb: pegasus: Proper error handing when setting pegasus' MAC address
  net: core: document two new elements of struct net_device
  netlink: fix policy dump leak
  net/mlx5e: Fix race condition on nhe->n pointer in neigh update
  net/mlx5e: Fix VLAN create flow
  ...

rxrpc: Fix server keyring leak

If someone calls setsockopt() twice to set a server key keyring, the first
keyring is leaked.

Fix it to return an error instead if the server key keyring is already set.

Fixes: 17926a79320a ("[AF_RXRPC]: Provide secure RxRPC sockets for use by userspace and kernel both")
Signed-off-by: David Howells <dhowells@redhat.com>

rxrpc: The server keyring isn't network-namespaced

The keyring containing the server's tokens isn't network-namespaced, so it
shouldn't be looked up with a network namespace. It is expected to be
owned specifically by the server, so namespacing is unnecessary.

Fixes: a58946c158a0 ("keys: Pass the network namespace into request_key mechanism")
Signed-off-by: David Howells <dhowells@redhat.com>

rxrpc: Fix accept on a connection that need securing

When a new incoming call arrives at an userspace rxrpc socket on a new
connection that has a security class set, the code currently pushes it onto
the accept queue to hold a ref on it for the socket.  This doesn't work,
however, as recvmsg() pops it off, notices that it's in the SERVER_SECURING
state and discards the ref.  This means that the call runs out of refs too
early and the kernel oopses.

By contrast, a kernel rxrpc socket manually pre-charges the incoming call
pool with calls that already have user call IDs assigned, so they are ref'd
by the call tree on the socket.

Change the mode of operation for userspace rxrpc server sockets to work
like this too.  Although this is a UAPI change, server sockets aren't
currently functional.

Fixes: 248f219cb8bc ("rxrpc: Rewrite the data and ack handling code")
Signed-off-by: David Howells <dhowells@redhat.com>

rxrpc: Fix some missing _bh annotations on locking conn->state_lock

conn->state_lock may be taken in softirq mode, but a previous patch
replaced an outer lock in the response-packet event handling code, and lost
the _bh from that when doing so.

Fix this by applying the _bh annotation to the state_lock locking.

Fixes: a1399f8bb033 ("rxrpc: Call channels should have separate call number spaces")
Signed-off-by: David Howells <dhowells@redhat.com>

rxrpc: Downgrade the BUG() for unsupported token type in rxrpc_read()

If rxrpc_read() (which allows KEYCTL_READ to read a key), sees a token of a
type it doesn't recognise, it can BUG in a couple of places, which is
unnecessary as it can easily get back to userspace.

Fix this to print an error message instead.

Fixes: 99455153d067 ("RxRPC: Parse security index 5 keys (Kerberos 5)")
Signed-off-by: David Howells <dhowells@redhat.com>

rxrpc: Fix rxkad token xdr encoding

The session key should be encoded with just the 8 data bytes and
no length; ENCODE_DATA precedes it with a 4 byte length, which
confuses some existing tools that try to parse this format.

Add an ENCODE_BYTES macro that does not include a length, and use
it for the key. Also adjust the expected length.

Note that commit 774521f353e1d ("rxrpc: Fix an assertion in
rxrpc_read()") had fixed a BUG by changing the length rather than
fixing the encoding. The original length was correct.

Fixes: 99455153d067 ("RxRPC: Parse security index 5 keys (Kerberos 5)")
Signed-off-by: Marc Dionne <marc.dionne@auristor.com>
Signed-off-by: David Howells <dhowells@redhat.com>

net: phy: marvell: Use phy_read_paged() instead of open coding it

Convert m88e1318_get_wol() to use the well implemented phy_read_paged()
instead of open coding it.

Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Reviewed-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: propagate switchdev vlan_filtering prepare phase to drivers

A driver may refuse to enable VLAN filtering for any reason beyond what
the DSA framework cares about, such as:
- having tc-flower rules that rely on the switch being VLAN-aware
- the particular switch does not support VLAN, even if the driver does
(the DSA framework just checks for the presence of the .port_vlan_add
and .port_vlan_del pointers)
- simply not supporting this configuration to be toggled at runtime

Currently, when a driver rejects a configuration it cannot support, it
does this from the commit phase, which triggers various warnings in
switchdev.

So propagate the prepare phase to drivers, to give them the ability to
refuse invalid configurations cleanly and avoid the warnings.

Since we need to modify all function prototypes and check for the
prepare phase from within the drivers, take that opportunity and move
the existing driver restrictions within the prepare phase where that is
possible and easy.

Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: Woojung Huh <woojung.huh@microchip.com>
Cc: Microchip Linux Driver Support <UNGLinuxDriver@microchip.com>
Cc: Sean Wang <sean.wang@mediatek.com>
Cc: Landen Chao <Landen.Chao@mediatek.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Vivien Didelot <vivien.didelot@gmail.com>
Cc: Jonathan McDowell <noodles@earth.li>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

platform/x86: thinkpad_acpi: re-initialize ACPI buffer size when reuse

Evaluating ACPI _BCL could fail, then ACPI buffer size will be set to 0.
When reuse this ACPI buffer, AE_BUFFER_OVERFLOW will be triggered.

Re-initialize buffer size will make ACPI evaluate successfully.

Fixes: 46445b6b896fd ("thinkpad-acpi: fix handle locate for video and query of _BCL")
Signed-off-by: Aaron Ma <aaron.ma@canonical.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

Merge branch 'net-Constify-struct-genl_small_ops'

Rikard Falkeborn says:

====================
net: Constify struct genl_small_ops

Make a couple of static struct genl_small_ops const to allow the compiler
to put them in read-only memory. Patches are independent.

v2: Rebase on net-next, genl_ops -> genl_small_ops
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

net: openvswitch: Constify static struct genl_small_ops

The only usage of these is to assign their address to the small_ops field
in the genl_family struct, which is a const pointer, and applying
ARRAY_SIZE() on them. Make them const to allow the compiler to put them
in read-only memory.

Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

mptcp: Constify mptcp_pm_ops

The only usages of mptcp_pm_ops is to assign its address to the small_ops
field of the genl_family struct, which is a const pointer, and applying
ARRAY_SIZE() on it. Make it const to allow the compiler to put it in
read-only memory.

Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Linux 5.9-rc8