Cong Wang [Sat, 28 Mar 2020 19:12:59 +0000 (12:12 -0700)]
net_sched: add a temporary refcnt for struct tcindex_data
[ Upstream commit
304e024216a802a7dc8ba75d36de82fa136bbf3e ]
Although we intentionally use an ordered workqueue for all tc
filter works, the ordering is not guaranteed by RCU work,
given that tcf_queue_work() is esstenially a call_rcu().
This problem is demostrated by Thomas:
CPU 0:
tcf_queue_work()
tcf_queue_work(&r->rwork, tcindex_destroy_rexts_work);
-> Migration to CPU 1
CPU 1:
tcf_queue_work(&p->rwork, tcindex_destroy_work);
so the 2nd work could be queued before the 1st one, which leads
to a free-after-free.
Enforcing this order in RCU work is hard as it requires to change
RCU code too. Fortunately we can workaround this problem in tcindex
filter by taking a temporary refcnt, we only refcnt it right before
we begin to destroy it. This simplifies the code a lot as a full
refcnt requires much more changes in tcindex_set_parms().
Reported-by: syzbot+46f513c3033d592409d2@syzkaller.appspotmail.com
Fixes:
3d210534cc93 ("net_sched: fix a race condition in tcindex_destroy()")
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Paul E. McKenney <paulmck@kernel.org>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Reviewed-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Oleksij Rempel [Fri, 3 Apr 2020 07:53:25 +0000 (09:53 +0200)]
net: phy: micrel: kszphy_resume(): add delay after genphy_resume() before accessing PHY registers
[ Upstream commit
6110dff776f7fa65c35850ef65b41d3b39e2fac2 ]
After the power-down bit is cleared, the chip internally triggers a
global reset. According to the KSZ9031 documentation, we have to wait at
least 1ms for the reset to finish.
If the chip is accessed during reset, read will return 0xffff, while
write will be ignored. Depending on the system performance and MDIO bus
speed, we may or may not run in to this issue.
This bug was discovered on an iMX6QP system with KSZ9031 PHY and
attached PHY interrupt line. If IRQ was used, the link status update was
lost. In polling mode, the link status update was always correct.
The investigation showed, that during a read-modify-write access, the
read returned 0xffff (while the chip was still in reset) and
corresponding write hit the chip _after_ reset and triggered (due to the
0xffff) another reset in an undocumented bit (register 0x1f, bit 1),
resulting in the next write being lost due to the new reset cycle.
This patch fixes the issue by adding a 1...2 ms sleep after the
genphy_resume().
Fixes:
836384d2501d ("net: phy: micrel: Add specific suspend")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Chuanhong Guo [Fri, 3 Apr 2020 11:28:24 +0000 (19:28 +0800)]
net: dsa: mt7530: fix null pointer dereferencing in port5 setup
[ Upstream commit
0452800f6db4ed0a42ffb15867c0acfd68829f6a ]
The 2nd gmac of mediatek soc ethernet may not be connected to a PHY
and a phy-handle isn't always available.
Unfortunately, mt7530 dsa driver assumes that the 2nd gmac is always
connected to switch port 5 and setup mt7530 according to phy address
of 2nd gmac node, causing null pointer dereferencing when phy-handle
isn't defined in dts.
This commit fix this setup code by checking return value of
of_parse_phandle before using it.
Fixes:
38f790a80560 ("net: dsa: mt7530: Add support for port 5")
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: René van Dorst <opensource@vdorst.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Florian Fainelli [Sun, 5 Apr 2020 20:00:30 +0000 (13:00 -0700)]
net: dsa: bcm_sf2: Ensure correct sub-node is parsed
[ Upstream commit
afa3b592953bfaecfb4f2f335ec5f935cff56804 ]
When the bcm_sf2 was converted into a proper platform device driver and
used the new dsa_register_switch() interface, we would still be parsing
the legacy DSA node that contained all the port information since the
platform firmware has intentionally maintained backward and forward
compatibility to client programs. Ensure that we do parse the correct
node, which is "ports" per the revised DSA binding.
Fixes:
d9338023fb8e ("net: dsa: bcm_sf2: Make it a real platform device driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Florian Fainelli [Sat, 4 Apr 2020 21:35:17 +0000 (14:35 -0700)]
net: dsa: bcm_sf2: Do not register slave MDIO bus with OF
[ Upstream commit
536fab5bf5826404534a6c271f622ad2930d9119 ]
We were registering our slave MDIO bus with OF and doing so with
assigning the newly created slave_mii_bus of_node to the master MDIO bus
controller node. This is a bad thing to do for a number of reasons:
- we are completely lying about the slave MII bus is arranged and yet we
still want to control which MDIO devices it probes. It was attempted
before to play tricks with the bus_mask to perform that:
https://www.spinics.net/lists/netdev/msg429420.html but the approach
was rightfully rejected
- the device_node reference counting is messed up and we are effectively
doing a double probe on the devices we already probed using the
master, this messes up all resources reference counts (such as clocks)
The proper fix for this as indicated by David in his reply to the
thread above is to use a platform data style registration so as to
control exactly which devices we probe:
https://www.spinics.net/lists/netdev/msg430083.html
By using mdiobus_register(), our slave_mii_bus->phy_mask value is used
as intended, and all the PHY addresses that must be redirected towards
our slave MDIO bus is happening while other addresses get redirected
towards the master MDIO bus.
Fixes:
461cd1b03e32 ("net: dsa: bcm_sf2: Register our slave MDIO bus")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jarod Wilson [Mon, 30 Mar 2020 15:22:19 +0000 (11:22 -0400)]
ipv6: don't auto-add link-local address to lag ports
[ Upstream commit
744fdc8233f6aa9582ce08a51ca06e59796a3196 ]
Bonding slave and team port devices should not have link-local addresses
automatically added to them, as it can interfere with openvswitch being
able to properly add tc ingress.
Basic reproducer, courtesy of Marcelo:
$ ip link add name bond0 type bond
$ ip link set dev ens2f0np0 master bond0
$ ip link set dev ens2f1np2 master bond0
$ ip link set dev bond0 up
$ ip a s
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN
group default qlen 1000
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
valid_lft forever preferred_lft forever
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
2: ens2f0np0: <BROADCAST,MULTICAST,SLAVE,UP,LOWER_UP> mtu 1500 qdisc
mq master bond0 state UP group default qlen 1000
link/ether 00:0f:53:2f:ea:40 brd ff:ff:ff:ff:ff:ff
5: ens2f1np2: <NO-CARRIER,BROADCAST,MULTICAST,SLAVE,UP> mtu 1500 qdisc
mq master bond0 state DOWN group default qlen 1000
link/ether 00:0f:53:2f:ea:40 brd ff:ff:ff:ff:ff:ff
11: bond0: <BROADCAST,MULTICAST,MASTER,UP,LOWER_UP> mtu 1500 qdisc
noqueue state UP group default qlen 1000
link/ether 00:0f:53:2f:ea:40 brd ff:ff:ff:ff:ff:ff
inet6 fe80::20f:53ff:fe2f:ea40/64 scope link
valid_lft forever preferred_lft forever
(above trimmed to relevant entries, obviously)
$ sysctl net.ipv6.conf.ens2f0np0.addr_gen_mode=0
net.ipv6.conf.ens2f0np0.addr_gen_mode = 0
$ sysctl net.ipv6.conf.ens2f1np2.addr_gen_mode=0
net.ipv6.conf.ens2f1np2.addr_gen_mode = 0
$ ip a l ens2f0np0
2: ens2f0np0: <BROADCAST,MULTICAST,SLAVE,UP,LOWER_UP> mtu 1500 qdisc
mq master bond0 state UP group default qlen 1000
link/ether 00:0f:53:2f:ea:40 brd ff:ff:ff:ff:ff:ff
inet6 fe80::20f:53ff:fe2f:ea40/64 scope link tentative
valid_lft forever preferred_lft forever
$ ip a l ens2f1np2
5: ens2f1np2: <NO-CARRIER,BROADCAST,MULTICAST,SLAVE,UP> mtu 1500 qdisc
mq master bond0 state DOWN group default qlen 1000
link/ether 00:0f:53:2f:ea:40 brd ff:ff:ff:ff:ff:ff
inet6 fe80::20f:53ff:fe2f:ea40/64 scope link tentative
valid_lft forever preferred_lft forever
Looks like addrconf_sysctl_addr_gen_mode() bypasses the original "is
this a slave interface?" check added by commit
c2edacf80e15, and
results in an address getting added, while w/the proposed patch added,
no address gets added. This simply adds the same gating check to another
code path, and thus should prevent the same devices from erroneously
obtaining an ipv6 link-local address.
Fixes:
d35a00b8e33d ("net/ipv6: allow sysctl to change link-local address generation mode")
Reported-by: Moshe Levi <moshele@mellanox.com>
CC: Stephen Hemminger <stephen@networkplumber.org>
CC: Marcelo Ricardo Leitner <mleitner@redhat.com>
CC: netdev@vger.kernel.org
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Herat Ramani [Tue, 31 Mar 2020 19:46:09 +0000 (01:16 +0530)]
cxgb4: fix MPS index overwrite when setting MAC address
[ Upstream commit
41aa8561ca3fc5748391f08cc5f3e561923da52c ]
cxgb4_update_mac_filt() earlier requests firmware to add a new MAC
address into MPS TCAM. The MPS TCAM index returned by firmware is
stored in pi->xact_addr_filt. However, the saved MPS TCAM index gets
overwritten again with the return value of cxgb4_update_mac_filt(),
which is wrong.
When trying to update to another MAC address later, the wrong MPS TCAM
index is sent to firmware, which causes firmware to return error,
because it's not the same MPS TCAM index that firmware had sent
earlier to driver.
So, fix by removing the wrong overwrite being done after call to
cxgb4_update_mac_filt().
Fixes:
3f8cfd0d95e6 ("cxgb4/cxgb4vf: Program hash region for {t4/t4vf}_change_mac()")
Signed-off-by: Herat Ramani <herat@chelsio.com>
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Heiner Kallweit [Tue, 7 Apr 2020 22:01:42 +0000 (00:01 +0200)]
net: phy: realtek: fix handling of RTL8105e-integrated PHY
[ No applicable upstream commit ]
After the referenced fix it turned out that one particular RTL8168
chip version (RTL8105e) does not work on 5.4 because no dedicated PHY
driver exists. Adding this PHY driver was done for fixing a different
issue for versions from 5.5 already. I re-send the same change for 5.4
because the commit message differs.
Fixes:
2e8c339b4946 ("r8169: fix PHY driver check on platforms w/o module softdeps")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Greg Kroah-Hartman [Wed, 8 Apr 2020 07:08:47 +0000 (09:08 +0200)]
Linux 5.4.31
Randy Dunlap [Thu, 2 Apr 2020 04:10:58 +0000 (21:10 -0700)]
mm: mempolicy: require at least one nodeid for MPOL_PREFERRED
commit
aa9f7d5172fac9bf1f09e678c35e287a40a7b7dd upstream.
Using an empty (malformed) nodelist that is not caught during mount option
parsing leads to a stack-out-of-bounds access.
The option string that was used was: "mpol=prefer:,". However,
MPOL_PREFERRED requires a single node number, which is not being provided
here.
Add a check that 'nodes' is not empty after parsing for MPOL_PREFERRED's
nodeid.
Fixes:
095f1fc4ebf3 ("mempolicy: rework shmem mpol parsing and display")
Reported-by: Entropy Moe <3ntr0py1337@gmail.com>
Reported-by: syzbot+b055b1a6b2b958707a21@syzkaller.appspotmail.com
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Tested-by: syzbot+b055b1a6b2b958707a21@syzkaller.appspotmail.com
Cc: Lee Schermerhorn <lee.schermerhorn@hp.com>
Link: http://lkml.kernel.org/r/89526377-7eb6-b662-e1d8-4430928abde9@infradead.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Daniel Jordan [Tue, 3 Dec 2019 19:31:11 +0000 (14:31 -0500)]
padata: always acquire cpu_hotplug_lock before pinst->lock
commit
38228e8848cd7dd86ccb90406af32de0cad24be3 upstream.
lockdep complains when padata's paths to update cpumasks via CPU hotplug
and sysfs are both taken:
# echo 0 > /sys/devices/system/cpu/cpu1/online
# echo ff > /sys/kernel/pcrypt/pencrypt/parallel_cpumask
======================================================
WARNING: possible circular locking dependency detected
5.4.0-rc8-padata-cpuhp-v3+ #1 Not tainted
------------------------------------------------------
bash/205 is trying to acquire lock:
ffffffff8286bcd0 (cpu_hotplug_lock.rw_sem){++++}, at: padata_set_cpumask+0x2b/0x120
but task is already holding lock:
ffff8880001abfa0 (&pinst->lock){+.+.}, at: padata_set_cpumask+0x26/0x120
which lock already depends on the new lock.
padata doesn't take cpu_hotplug_lock and pinst->lock in a consistent
order. Which should be first? CPU hotplug calls into padata with
cpu_hotplug_lock already held, so it should have priority.
Fixes:
6751fb3c0e0c ("padata: Use get_online_cpus/put_online_cpus")
Signed-off-by: Daniel Jordan <daniel.m.jordan@oracle.com>
Cc: Eric Biggers <ebiggers@kernel.org>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Cc: linux-crypto@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Amritha Nambiar [Mon, 24 Feb 2020 18:56:00 +0000 (10:56 -0800)]
net: Fix Tx hash bound checking
commit
6e11d1578fba8d09d03a286740ffcf336d53928c upstream.
Fixes the lower and upper bounds when there are multiple TCs and
traffic is on the the same TC on the same device.
The lower bound is represented by 'qoffset' and the upper limit for
hash value is 'qcount + qoffset'. This gives a clean Rx to Tx queue
mapping when there are multiple TCs, as the queue indices for upper TCs
will be offset by 'qoffset'.
v2: Fixed commit description based on comments.
Fixes:
1b837d489e06 ("net: Revoke export for __skb_tx_hash, update it to just be static skb_tx_hash")
Fixes:
eadec877ce9c ("net: Add support for subordinate traffic classes to netdev_pick_tx")
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Reviewed-by: Alexander Duyck <alexander.h.duyck@linux.intel.com>
Reviewed-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mika Westerberg [Wed, 26 Feb 2020 13:21:22 +0000 (16:21 +0300)]
i2c: i801: Do not add ICH_RES_IO_SMI for the iTCO_wdt device
commit
04bbb97d1b732b2d197f103c5818f5c214a4cf81 upstream.
Martin noticed that nct6775 driver does not load properly on his system
in v5.4+ kernels. The issue was bisected to commit
b84398d6d7f9 ("i2c:
i801: Use iTCO version 6 in Cannon Lake PCH and beyond") but it is
likely not the culprit because the faulty code has been in the driver
already since commit
9424693035a5 ("i2c: i801: Create iTCO device on
newer Intel PCHs"). So more likely some commit that added PCI IDs of
recent chipsets made the driver to create the iTCO_wdt device on Martins
system.
The issue was debugged to be PCI configuration access to the PMC device
that is not present. This returns all 1's when read and this caused the
iTCO_wdt driver to accidentally request resourses used by nct6775.
It turns out that the SMI resource is only required for some ancient
systems, not the ones supported by this driver. For this reason do not
populate the SMI resource at all and drop all the related code. The
driver now always populates the main I/O resource and only in case of SPT
(Intel Sunrisepoint) compatible devices it adds another resource for the
NO_REBOOT bit. These two resources are of different types so
platform_get_resource() used by the iTCO_wdt driver continues to find
the both resources at index 0.
Link: https://lore.kernel.org/linux-hwmon/CAM1AHpQ4196tyD=HhBu-2donSsuogabkfP03v1YF26Q7_BgvgA@mail.gmail.com/
Fixes:
9424693035a5 ("i2c: i801: Create iTCO device on newer Intel PCHs")
[wsa: complete fix needs all of http://patchwork.ozlabs.org/project/linux-i2c/list/?series=160959&state=*]
Reported-by: Martin Volf <martin.volf.42@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mika Westerberg [Wed, 26 Feb 2020 13:21:21 +0000 (16:21 +0300)]
watchdog: iTCO_wdt: Make ICH_RES_IO_SMI optional
commit
e42b0c24389d5a1602e77db4f6def0d5a19e3e43 upstream.
The iTCO_wdt driver only needs ICH_RES_IO_SMI I/O resource when either
turn_SMI_watchdog_clear_off module parameter is set to match ->iTCO_version
(or higher), and when legacy iTCO_vendorsupport is set. Modify the driver
so that ICH_RES_IO_SMI is optional if the two conditions are not met.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mika Westerberg [Wed, 26 Feb 2020 13:21:20 +0000 (16:21 +0300)]
watchdog: iTCO_wdt: Export vendorsupport
commit
7ca6ee38909109751bfab79e9f6c570d2ed258c6 upstream.
In preparation for making ->smi_res optional the iTCO_wdt driver needs
to know whether vendorsupport is being set to non-zero. For this reason
export the variable.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Neal Cardwell [Sat, 22 Feb 2020 16:21:15 +0000 (11:21 -0500)]
tcp: fix TFO SYNACK undo to avoid double-timestamp-undo
commit
dad8cea7add96a353fa1898b5ccefbb72da66f29 upstream.
In a rare corner case the new logic for undo of SYNACK RTO could
result in triggering the warning in tcp_fastretrans_alert() that says:
WARN_ON(tp->retrans_out != 0);
The warning looked like:
WARNING: CPU: 1 PID: 1 at net/ipv4/tcp_input.c:2818 tcp_ack+0x13e0/0x3270
The sequence that tickles this bug is:
- Fast Open server receives TFO SYN with data, sends SYNACK
- (client receives SYNACK and sends ACK, but ACK is lost)
- server app sends some data packets
- (N of the first data packets are lost)
- server receives client ACK that has a TS ECR matching first SYNACK,
and also SACKs suggesting the first N data packets were lost
- server performs TS undo of SYNACK RTO, then immediately
enters recovery
- buggy behavior then performed a *second* undo that caused
the connection to be in CA_Open with retrans_out != 0
Basically, the incoming ACK packet with SACK blocks causes us to first
undo the cwnd reduction from the SYNACK RTO, but then immediately
enters fast recovery, which then makes us eligible for undo again. And
then tcp_rcv_synrecv_state_fastopen() accidentally performs an undo
using a "mash-up" of state from two different loss recovery phases: it
uses the timestamp info from the ACK of the original SYNACK, and the
undo_marker from the fast recovery.
This fix refines the logic to only invoke the tcp_try_undo_loss()
inside tcp_rcv_synrecv_state_fastopen() if the connection is still in
CA_Loss. If peer SACKs triggered fast recovery, then
tcp_rcv_synrecv_state_fastopen() can't safely undo.
Fixes:
794200d66273 ("tcp: undo cwnd on Fast Open spurious SYNACK retransmit")
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mike Marciniszyn [Fri, 20 Mar 2020 20:02:10 +0000 (16:02 -0400)]
IB/hfi1: Ensure pq is not left on waitlist
commit
9a293d1e21a6461a11b4217b155bf445e57f4131 upstream.
The following warning can occur when a pq is left on the dmawait list and
the pq is then freed:
WARNING: CPU: 47 PID: 3546 at lib/list_debug.c:29 __list_add+0x65/0xc0
list_add corruption. next->prev should be prev (
ffff939228da1880), but was
ffff939cabb52230. (next=
ffff939cabb52230).
Modules linked in: mmfs26(OE) mmfslinux(OE) tracedev(OE) 8021q garp mrp ib_isert iscsi_target_mod target_core_mod crc_t10dif crct10dif_generic opa_vnic rpcrdma ib_iser libiscsi scsi_transport_iscsi ib_ipoib(OE) bridge stp llc iTCO_wdt iTCO_vendor_support intel_powerclamp coretemp intel_rapl iosf_mbi kvm_intel kvm irqbypass crct10dif_pclmul crct10dif_common crc32_pclmul ghash_clmulni_intel aesni_intel lrw gf128mul glue_helper ablk_helper cryptd ast ttm drm_kms_helper syscopyarea sysfillrect sysimgblt fb_sys_fops drm pcspkr joydev drm_panel_orientation_quirks i2c_i801 mei_me lpc_ich mei wmi ipmi_si ipmi_devintf ipmi_msghandler nfit libnvdimm acpi_power_meter acpi_pad hfi1(OE) rdmavt(OE) rdma_ucm ib_ucm ib_uverbs ib_umad rdma_cm ib_cm iw_cm ib_core binfmt_misc numatools(OE) xpmem(OE) ip_tables
nfsv3 nfs_acl nfs lockd grace sunrpc fscache igb ahci libahci i2c_algo_bit dca libata ptp pps_core crc32c_intel [last unloaded: i2c_algo_bit]
CPU: 47 PID: 3546 Comm: wrf.exe Kdump: loaded Tainted: G W OE ------------ 3.10.0-957.41.1.el7.x86_64 #1
Hardware name: HPE.COM HPE SGI 8600-XA730i Gen10/X11DPT-SB-SG007, BIOS SBED1229 01/22/2019
Call Trace:
[<
ffffffff91f65ac0>] dump_stack+0x19/0x1b
[<
ffffffff91898b78>] __warn+0xd8/0x100
[<
ffffffff91898bff>] warn_slowpath_fmt+0x5f/0x80
[<
ffffffff91a1dabe>] ? ___slab_alloc+0x24e/0x4f0
[<
ffffffff91b97025>] __list_add+0x65/0xc0
[<
ffffffffc03926a5>] defer_packet_queue+0x145/0x1a0 [hfi1]
[<
ffffffffc0372987>] sdma_check_progress+0x67/0xa0 [hfi1]
[<
ffffffffc03779d2>] sdma_send_txlist+0x432/0x550 [hfi1]
[<
ffffffff91a20009>] ? kmem_cache_alloc+0x179/0x1f0
[<
ffffffffc0392973>] ? user_sdma_send_pkts+0xc3/0x1990 [hfi1]
[<
ffffffffc0393e3a>] user_sdma_send_pkts+0x158a/0x1990 [hfi1]
[<
ffffffff918ab65e>] ? try_to_del_timer_sync+0x5e/0x90
[<
ffffffff91a3fe1a>] ? __check_object_size+0x1ca/0x250
[<
ffffffffc0395546>] hfi1_user_sdma_process_request+0xd66/0x1280 [hfi1]
[<
ffffffffc034e0da>] hfi1_aio_write+0xca/0x120 [hfi1]
[<
ffffffff91a4245b>] do_sync_readv_writev+0x7b/0xd0
[<
ffffffff91a4409e>] do_readv_writev+0xce/0x260
[<
ffffffff918df69f>] ? pick_next_task_fair+0x5f/0x1b0
[<
ffffffff918db535>] ? sched_clock_cpu+0x85/0xc0
[<
ffffffff91f6b16a>] ? __schedule+0x13a/0x860
[<
ffffffff91a442c5>] vfs_writev+0x35/0x60
[<
ffffffff91a4447f>] SyS_writev+0x7f/0x110
[<
ffffffff91f78ddb>] system_call_fastpath+0x22/0x27
The issue happens when wait_event_interruptible_timeout() returns a value
<= 0.
In that case, the pq is left on the list. The code continues sending
packets and potentially can complete the current request with the pq still
on the dmawait list provided no descriptor shortage is seen.
If the pq is torn down in that state, the sdma interrupt handler could
find the now freed pq on the list with list corruption or memory
corruption resulting.
Fix by adding a flush routine to ensure that the pq is never on a list
after processing a request.
A follow-up patch series will address issues with seqlock surfaced in:
https://lore.kernel.org/r/
20200320003129.GP20941@ziepe.ca
The seqlock use for sdma will then be converted to a spin lock since the
list_empty() doesn't need the protection afforded by the sequence lock
currently in use.
Fixes:
a0d406934a46 ("staging/rdma/hfi1: Add page lock limit check for SDMA requests")
Link: https://lore.kernel.org/r/20200320200200.23203.37777.stgit@awfm-01.aw.intel.com
Reviewed-by: Kaike Wan <kaike.wan@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
David Howells [Fri, 13 Mar 2020 17:30:27 +0000 (17:30 +0000)]
rxrpc: Fix sendmsg(MSG_WAITALL) handling
commit
498b577660f08cef5d9e78e0ed6dcd4c0939e98c upstream.
Fix the handling of sendmsg() with MSG_WAITALL for userspace to round the
timeout for when a signal occurs up to at least two jiffies as a 1 jiffy
timeout may end up being effectively 0 if jiffies wraps at the wrong time.
Fixes:
bc5e3a546d55 ("rxrpc: Use MSG_WAITALL to tell sendmsg() to temporarily ignore signals")
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Luca Coelho [Fri, 6 Mar 2020 13:16:25 +0000 (15:16 +0200)]
iwlwifi: dbg: don't abort if sending DBGC_SUSPEND_RESUME fails
commit
699b760bd29edba736590fffef7654cb079c753e upstream.
If the firmware is in a bad state or not initialized fully, sending
the DBGC_SUSPEND_RESUME command fails but we can still collect logs.
Instead of aborting the entire dump process, simply ignore the error.
By removing the last callpoint that was checking the return value, we
can also convert the function to return void.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Fixes:
576058330f2d ("iwlwifi: dbg: support debug recording suspend resume command")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200306151129.dcec37b2efd4.I8dcd190431d110a6a0e88095ce93591ccfb3d78d@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mordechay Goodstein [Fri, 6 Mar 2020 13:16:24 +0000 (15:16 +0200)]
iwlwifi: yoyo: don't add TLV offset when reading FIFOs
commit
a5688e600e78f9fc68102bf0fe5c797fc2826abe upstream.
The TLV offset is only used to read registers, while the offset used for
the FIFO addresses are hard coded in the driver and not given by the
TLV.
If we try to apply the TLV offset when reading the FIFOs, we'll read
from invalid addresses, causing the driver to hang.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Fixes:
8d7dea25ada7 ("iwlwifi: dbg_ini: implement Rx fifos dump")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200306151129.fbab869c26fa.I4ddac20d02f9bce41855a816aa6855c89bc3874e@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mordechay Goodstein [Fri, 6 Mar 2020 13:16:22 +0000 (15:16 +0200)]
iwlwifi: consider HE capability when setting LDPC
commit
cb377dfda1755b3bc01436755d866c8e5336a762 upstream.
The AP may set the LDPC capability only in HE (IEEE80211_HE_PHY_CAP1),
but we were checking it only in the HT capabilities.
If we don't use this capability when required, the DSP gets the wrong
configuration in HE and doesn't work properly.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Fixes:
befebbb30af0 ("iwlwifi: rs: consider LDPC capability in case of HE")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200306151128.492d167c1a25.I1ad1353dbbf6c99ae57814be750f41a1c9f7f4ac@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tariq Toukan [Mon, 24 Feb 2020 11:56:53 +0000 (13:56 +0200)]
net/mlx5e: kTLS, Fix wrong value in record tracker enum
commit
f28ca65efa87b3fb8da3d69ca7cb1ebc0448de66 upstream.
Fix to match the HW spec: TRACKING state is 1, SEARCHING is 2.
No real issue for now, as these values are not currently used.
Fixes:
d2ead1f360e8 ("net/mlx5e: Add kTLS TX HW offload support")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Bibby Hsieh [Fri, 14 Feb 2020 04:35:45 +0000 (12:35 +0800)]
soc: mediatek: knows_txdone needs to be set in Mediatek CMDQ helper
commit
ce35e21d82bcac8b3fd5128888f9e233f8444293 upstream.
Mediatek CMDQ driver have a mechanism to do TXDONE_BY_ACK,
so we should set knows_txdone.
Fixes:
576f1b4bc802 ("soc: mediatek: Add Mediatek CMDQ helper")
Cc: stable@vger.kernel.org # v5.0+
Signed-off-by: Bibby Hsieh <bibby.hsieh@mediatek.com>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Geoffrey Allott [Thu, 19 Mar 2020 14:00:48 +0000 (14:00 +0000)]
ALSA: hda/ca0132 - Add Recon3Di quirk to handle integrated sound on EVGA X99 Classified motherboard
commit
e9097e47e349b747dee50f935216de0ffb662962 upstream.
I have a system which has an EVGA X99 Classified motherboard. The pin
assignments for the HD Audio controller are not correct under Linux.
Windows 10 works fine and informs me that it's using the Recon3Di
driver, and on Linux, `cat
/sys/class/sound/card0/device/subsystem_{vendor,device}` yields
0x3842
0x1038
This patch adds a corresponding entry to the quirk list.
Signed-off-by: Geoffrey Allott <geoffrey@allott.email>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/a6cd56b678c00ce2db3685e4278919f2584f8244.camel@allott.email
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mike Snitzer [Thu, 2 Apr 2020 23:36:26 +0000 (19:36 -0400)]
Revert "dm: always call blk_queue_split() in dm_process_bio()"
commit
120c9257f5f19e5d1e87efcbb5531b7cd81b7d74 upstream.
This reverts commit
effd58c95f277744f75d6e08819ac859dbcbd351.
blk_queue_split() is causing excessive IO splitting -- because
blk_max_size_offset() depends on 'chunk_sectors' limit being set and
if it isn't (as is the case for DM targets!) it falls back to
splitting on a 'max_sectors' boundary regardless of offset.
"Fix" this by reverting back to _not_ using blk_queue_split() in
dm_process_bio() for normal IO (reads and writes). Long-term fix is
still TBD but it should focus on training blk_max_size_offset() to
call into a DM provided hook (to call DM's max_io_len()).
Test results from simple misaligned IO test on 4-way dm-striped device
with chunksize of 128K and stripesize of 512K:
xfs_io -d -c 'pread -b 2m 224s 4072s' /dev/mapper/stripe_dev
before this revert:
253,0 21 1 0.
000000000 2206 Q R 224 + 4072 [xfs_io]
253,0 21 2 0.
000008267 2206 X R 224 / 480 [xfs_io]
253,0 21 3 0.
000010530 2206 X R 224 / 256 [xfs_io]
253,0 21 4 0.
000027022 2206 X R 480 / 736 [xfs_io]
253,0 21 5 0.
000028751 2206 X R 480 / 512 [xfs_io]
253,0 21 6 0.
000033323 2206 X R 736 / 992 [xfs_io]
253,0 21 7 0.
000035130 2206 X R 736 / 768 [xfs_io]
253,0 21 8 0.
000039146 2206 X R 992 / 1248 [xfs_io]
253,0 21 9 0.
000040734 2206 X R 992 / 1024 [xfs_io]
253,0 21 10 0.
000044694 2206 X R 1248 / 1504 [xfs_io]
253,0 21 11 0.
000046422 2206 X R 1248 / 1280 [xfs_io]
253,0 21 12 0.
000050376 2206 X R 1504 / 1760 [xfs_io]
253,0 21 13 0.
000051974 2206 X R 1504 / 1536 [xfs_io]
253,0 21 14 0.
000055881 2206 X R 1760 / 2016 [xfs_io]
253,0 21 15 0.
000057462 2206 X R 1760 / 1792 [xfs_io]
253,0 21 16 0.
000060999 2206 X R 2016 / 2272 [xfs_io]
253,0 21 17 0.
000062489 2206 X R 2016 / 2048 [xfs_io]
253,0 21 18 0.
000066133 2206 X R 2272 / 2528 [xfs_io]
253,0 21 19 0.
000067507 2206 X R 2272 / 2304 [xfs_io]
253,0 21 20 0.
000071136 2206 X R 2528 / 2784 [xfs_io]
253,0 21 21 0.
000072764 2206 X R 2528 / 2560 [xfs_io]
253,0 21 22 0.
000076185 2206 X R 2784 / 3040 [xfs_io]
253,0 21 23 0.
000077486 2206 X R 2784 / 2816 [xfs_io]
253,0 21 24 0.
000080885 2206 X R 3040 / 3296 [xfs_io]
253,0 21 25 0.
000082316 2206 X R 3040 / 3072 [xfs_io]
253,0 21 26 0.
000085788 2206 X R 3296 / 3552 [xfs_io]
253,0 21 27 0.
000087096 2206 X R 3296 / 3328 [xfs_io]
253,0 21 28 0.
000093469 2206 X R 3552 / 3808 [xfs_io]
253,0 21 29 0.
000095186 2206 X R 3552 / 3584 [xfs_io]
253,0 21 30 0.
000099228 2206 X R 3808 / 4064 [xfs_io]
253,0 21 31 0.
000101062 2206 X R 3808 / 3840 [xfs_io]
253,0 21 32 0.
000104956 2206 X R 4064 / 4096 [xfs_io]
253,0 21 33 0.
001138823 0 C R 4096 + 200 [0]
after this revert:
253,0 18 1 0.
000000000 4430 Q R 224 + 3896 [xfs_io]
253,0 18 2 0.
000018359 4430 X R 224 / 256 [xfs_io]
253,0 18 3 0.
000028898 4430 X R 256 / 512 [xfs_io]
253,0 18 4 0.
000033535 4430 X R 512 / 768 [xfs_io]
253,0 18 5 0.
000065684 4430 X R 768 / 1024 [xfs_io]
253,0 18 6 0.
000091695 4430 X R 1024 / 1280 [xfs_io]
253,0 18 7 0.
000098494 4430 X R 1280 / 1536 [xfs_io]
253,0 18 8 0.
000114069 4430 X R 1536 / 1792 [xfs_io]
253,0 18 9 0.
000129483 4430 X R 1792 / 2048 [xfs_io]
253,0 18 10 0.
000136759 4430 X R 2048 / 2304 [xfs_io]
253,0 18 11 0.
000152412 4430 X R 2304 / 2560 [xfs_io]
253,0 18 12 0.
000160758 4430 X R 2560 / 2816 [xfs_io]
253,0 18 13 0.
000183385 4430 X R 2816 / 3072 [xfs_io]
253,0 18 14 0.
000190797 4430 X R 3072 / 3328 [xfs_io]
253,0 18 15 0.
000197667 4430 X R 3328 / 3584 [xfs_io]
253,0 18 16 0.
000218751 4430 X R 3584 / 3840 [xfs_io]
253,0 18 17 0.
000226005 4430 X R 3840 / 4096 [xfs_io]
253,0 18 18 0.
000250404 4430 Q R 4120 + 176 [xfs_io]
253,0 18 19 0.
000847708 0 C R 4096 + 24 [0]
253,0 18 20 0.
000855783 0 C R 4120 + 176 [0]
Fixes:
effd58c95f27774 ("dm: always call blk_queue_split() in dm_process_bio()")
Cc: stable@vger.kernel.org
Reported-by: Andreas Gruenbacher <agruenba@redhat.com>
Tested-by: Barry Marson <bmarson@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hans de Goede [Sun, 23 Feb 2020 15:32:08 +0000 (16:32 +0100)]
power: supply: axp288_charger: Add special handling for HP Pavilion x2 10
commit
9c80662a74cd2a5d1113f5c69d027face963a556 upstream.
Some HP Pavilion x2 10 models use an AXP288 for charging and fuel-gauge.
We use a native power_supply / PMIC driver in this case, because on most
models with an AXP288 the ACPI AC / Battery code is either completely
missing or relies on custom / proprietary ACPI OpRegions which Linux
does not implement.
The native drivers mostly work fine, but there are 2 problems:
1. These model uses a Type-C connector for charging which the AXP288 does
not support. As long as a Type-A charger (which uses the USB data pins for
charger type detection) is used everything is fine. But if a Type-C
charger is used (such as the charger shipped with the device) then the
charger is not recognized.
So we end up slowly discharging the device even though a charger is
connected, because we are limiting the current from the charger to 500mA.
To make things worse this happens with the device's official charger.
Looking at the ACPI tables HP has "solved" the problem of the AXP288 not
being able to recognize Type-C chargers by simply always programming the
input-current-limit at 3000mA and relying on a Vhold setting of 4.7V
(normally 4.4V) to limit the current intake if the charger cannot handle
this.
2. If no charger is connected when the machine boots then it boots with the
vbus-path disabled. On other devices this is done when a 5V boost converter
is active to avoid the PMIC trying to charge from the 5V boost output.
This is done when an OTG host cable is inserted and the ID pin on the
micro-B receptacle is pulled low, the ID pin has an ACPI event handler
associated with it which re-enables the vbus-path when the ID pin is pulled
high when the OTG cable is removed. The Type-C connector has no ID pin,
there is no ID pin handler and there appears to be no 5V boost converter,
so we end up not charging because the vbus-path is disabled, until we
unplug the charger which automatically clears the vbus-path disable bit and
then on the second plug-in of the adapter we start charging.
The HP Pavilion x2 10 models with an AXP288 do have mostly working ACPI
AC / Battery code which does not rely on custom / proprietary ACPI
OpRegions. So one possible solution would be to blacklist the AXP288
native power_supply drivers and add the HP Pavilion x2 10 with AXP288
DMI ids to the list of devices which should use the ACPI AC / Battery
code even though they have an AXP288 PMIC. This would require changes to
4 files: drivers/acpi/ac.c, drivers/power/supply/axp288_charger.c,
drivers/acpi/battery.c and drivers/power/supply/axp288_fuel_gauge.c.
Beside needing adding the same DMI matches to 4 different files, this
approach also triggers problem 2. from above, but then when suspended,
during suspend the machine will not wakeup because the vbus path is
disabled by the AML code when not charging, so the Vbus low-to-high
IRQ is not triggered, the CPU never wakes up and the device does not
charge even though the user likely things it is charging, esp. since
the charge status LED is directly coupled to an adapter being plugged
in and does not reflect actual charging.
This could be worked by enabling vbus-path explicitly from say the
axp288_charger driver's suspend handler.
So neither situation is ideal, in both cased we need to explicitly enable
the vbus-path to work around different variants of problem 2 above, this
requires a quirk in the axp288_charger code.
If we go the route of using the ACPI AC / Battery drivers then we need
modifications to 3 other drivers; and we need to partially disable the
axp288_charger code, while at the same time keeping it around to enable
vbus-path on suspend.
OTOH we can copy the hardcoding of 3A input-current-limit (we never touch
Vhold, so that would stay at 4.7V) to the axp288_charger code, which needs
changes regardless, then we concentrate all special handling of this
interesting device model in the axp288_charger code. That is what this
commit does.
Cc: stable@vger.kernel.org
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1791098
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hans de Goede [Mon, 23 Mar 2020 21:59:39 +0000 (22:59 +0100)]
extcon: axp288: Add wakeup support
commit
9c94553099efb2ba873cbdddfd416a8a09d0e5f1 upstream.
On devices with an AXP288, we need to wakeup from suspend when a charger
is plugged in, so that we can do charger-type detection and so that the
axp288-charger driver, which listens for our extcon events, can configure
the input-current-limit accordingly.
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Nicholas Johnson [Tue, 10 Mar 2020 13:22:52 +0000 (13:22 +0000)]
nvmem: check for NULL reg_read and reg_write before dereferencing
commit
3c91ef69a3e94f78546b246225ed573fbf1735b4 upstream.
Return -EPERM if reg_read is NULL in bin_attr_nvmem_read() or if
reg_write is NULL in bin_attr_nvmem_write().
This prevents NULL dereferences such as the one described in
03cd45d2e219 ("thunderbolt: Prevent crash if non-active NVMem file is
read")
Signed-off-by: Nicholas Johnson <nicholas.johnson-opensource@outlook.com.au>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20200310132257.23358-10-srinivas.kandagatla@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alexander Usyskin [Tue, 24 Mar 2020 21:07:30 +0000 (23:07 +0200)]
mei: me: add cedar fork device ids
commit
99397d33b763dc554d118aaa38cc5abc6ce985de upstream.
Add Cedar Fork (CDF) device ids, those belongs to the cannon point family.
Cc: <stable@vger.kernel.org>
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Link: https://lore.kernel.org/r/20200324210730.17672-1-tomas.winkler@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Eugene Syromiatnikov [Tue, 24 Mar 2020 04:22:13 +0000 (05:22 +0100)]
coresight: do not use the BIT() macro in the UAPI header
commit
9b6eaaf3db5e5888df7bca7fed7752a90f7fd871 upstream.
The BIT() macro definition is not available for the UAPI headers
(moreover, it can be defined differently in the user space); replace
its usage with the _BITUL() macro that is defined in <linux/const.h>.
Fixes:
237483aa5cf4 ("coresight: stm: adding driver for CoreSight STM component")
Signed-off-by: Eugene Syromiatnikov <esyr@redhat.com>
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Link: https://lore.kernel.org/r/20200324042213.GA10452@asgard.redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Kelsey Skunberg [Wed, 25 Mar 2020 15:17:08 +0000 (09:17 -0600)]
PCI: sysfs: Revert "rescan" file renames
commit
bd641fd8303a371e789e924291086268256766b0 upstream.
We changed these sysfs filenames:
.../pci_bus/<domain:bus>/rescan -> .../pci_bus/<domain:bus>/bus_rescan
.../<domain:bus:dev.fn>/rescan -> .../<domain:bus:dev.fn>/dev_rescan
and Ruslan reported [1] that this broke a userspace application.
Revert these name changes so both files are named "rescan" again.
Note that we have to use __ATTR() to assign custom C symbols, i.e.,
"struct device_attribute <symbol>".
[1] https://lore.kernel.org/r/CAB=otbSYozS-ZfxB0nCiNnxcbqxwrHOSYxJJtDKa63KzXbXgpw@mail.gmail.com
[bhelgaas: commit log, use __ATTR() both places so we don't have to rename
the attributes]
Fixes:
8bdfa145f582 ("PCI: sysfs: Define device attributes with DEVICE_ATTR*()")
Fixes:
4e2b79436e4f ("PCI: sysfs: Change DEVICE_ATTR() to DEVICE_ATTR_WO()")
Link: https://lore.kernel.org/r/20200325151708.32612-1-skunberg.kelsey@gmail.com
Signed-off-by: Kelsey Skunberg <kelsey.skunberg@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: stable@vger.kernel.org # v5.4+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Kishon Vijay Abraham I [Tue, 17 Mar 2020 10:01:54 +0000 (15:31 +0530)]
misc: pci_endpoint_test: Avoid using module parameter to determine irqtype
commit
b2ba9225e0313b1de631a44b7b48c109032bffec upstream.
commit
e03327122e2c ("pci_endpoint_test: Add 2 ioctl commands")
uses module parameter 'irqtype' in pci_endpoint_test_set_irq()
to check if IRQ vectors of a particular type (MSI or MSI-X or
LEGACY) is already allocated. However with multi-function devices,
'irqtype' will not correctly reflect the IRQ type of the PCI device.
Fix it here by adding 'irqtype' for each PCI device to show the
IRQ type of a particular PCI device.
Fixes:
e03327122e2c ("pci_endpoint_test: Add 2 ioctl commands")
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: stable@vger.kernel.org # v4.19+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Kishon Vijay Abraham I [Tue, 17 Mar 2020 10:01:57 +0000 (15:31 +0530)]
misc: pci_endpoint_test: Fix to support > 10 pci-endpoint-test devices
commit
6b443e5c80b67a7b8a85b33d052d655ef9064e90 upstream.
Adding more than 10 pci-endpoint-test devices results in
"kobject_add_internal failed for pci-endpoint-test.1 with -EEXIST, don't
try to register things with the same name in the same directory". This
is because commit
2c156ac71c6b ("misc: Add host side PCI driver for PCI
test function device") limited the length of the "name" to 20 characters.
Change the length of the name to 24 in order to support upto 10000
pci-endpoint-test devices.
Fixes:
2c156ac71c6b ("misc: Add host side PCI driver for PCI test function device")
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: stable@vger.kernel.org # v4.14+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
YueHaibing [Thu, 26 Mar 2020 03:26:18 +0000 (11:26 +0800)]
misc: rtsx: set correct pcr_ops for rts522A
commit
10cea23b6aae15e8324f4101d785687f2c514fe5 upstream.
rts522a should use rts522a_pcr_ops, which is
diffrent with rts5227 in phy/hw init setting.
Fixes:
ce6a5acc9387 ("mfd: rtsx: Add support for rts522A")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200326032618.20472-1-yuehaibing@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Guenter Roeck [Tue, 28 Jan 2020 22:14:57 +0000 (14:14 -0800)]
brcmfmac: abort and release host after error
[ Upstream commit
863844ee3bd38219c88e82966d1df36a77716f3e ]
With commit
216b44000ada ("brcmfmac: Fix use after free in
brcmf_sdio_readframes()") applied, we see locking timeouts in
brcmf_sdio_watchdog_thread().
brcmfmac: brcmf_escan_timeout: timer expired
INFO: task brcmf_wdog/mmc1:621 blocked for more than 120 seconds.
Not tainted 4.19.94-07984-g24ff99a0f713 #1
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
brcmf_wdog/mmc1 D 0 621 2 0x00000000 last_sleep:
2440793077. last_runnable:
2440766827
[<
c0aa1e60>] (__schedule) from [<
c0aa2100>] (schedule+0x98/0xc4)
[<
c0aa2100>] (schedule) from [<
c0853830>] (__mmc_claim_host+0x154/0x274)
[<
c0853830>] (__mmc_claim_host) from [<
bf10c5b8>] (brcmf_sdio_watchdog_thread+0x1b0/0x1f8 [brcmfmac])
[<
bf10c5b8>] (brcmf_sdio_watchdog_thread [brcmfmac]) from [<
c02570b8>] (kthread+0x178/0x180)
In addition to restarting or exiting the loop, it is also necessary to
abort the command and to release the host.
Fixes:
216b44000ada ("brcmfmac: Fix use after free in brcmf_sdio_readframes()")
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Matthias Kaehlcke <mka@chromium.org>
Cc: Brian Norris <briannorris@chromium.org>
Cc: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Acked-by: franky.lin@broadcom.com
Acked-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Daniel Jordan [Mon, 10 Feb 2020 18:11:00 +0000 (13:11 -0500)]
padata: fix uninitialized return value in padata_replace()
[ Upstream commit
41ccdbfd5427bbbf3ed58b16750113b38fad1780 ]
According to Geert's report[0],
kernel/padata.c: warning: 'err' may be used uninitialized in this
function [-Wuninitialized]: => 539:2
Warning is seen only with older compilers on certain archs. The
runtime effect is potentially returning garbage down the stack when
padata's cpumasks are modified before any pcrypt requests have run.
Simplest fix is to initialize err to the success value.
[0] http://lkml.kernel.org/r/
20200210135506.11536-1-geert@linux-m68k.org
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Fixes:
bbefa1dd6a6d ("crypto: pcrypt - Avoid deadlock by using per-instance padata queues")
Signed-off-by: Daniel Jordan <daniel.m.jordan@oracle.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Cc: linux-crypto@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Matthew Wilcox (Oracle) [Fri, 31 Jan 2020 10:07:55 +0000 (05:07 -0500)]
XArray: Fix xa_find_next for large multi-index entries
[ Upstream commit
bd40b17ca49d7d110adf456e647701ce74de2241 ]
Coverity pointed out that xas_sibling() was shifting xa_offset without
promoting it to an unsigned long first, so the shift could cause an
overflow and we'd get the wrong answer. The fix is obvious, and the
new test-case provokes UBSAN to report an error:
runtime error: shift exponent 60 is too large for 32-bit type 'int'
Fixes:
19c30f4dd092 ("XArray: Fix xa_find_after with multi-index entries")
Reported-by: Bjorn Helgaas <bhelgaas@google.com>
Reported-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Cc: stable@vger.kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
Tariq Toukan [Thu, 20 Feb 2020 11:40:24 +0000 (13:40 +0200)]
net/mlx5e: kTLS, Fix TCP seq off-by-1 issue in TX resync flow
[ Upstream commit
56917766def72f5afdf4235adb91b6897ff26d9d ]
We have an off-by-1 issue in the TCP seq comparison.
The last sequence number that belongs to the TCP packet's payload
is not "start_seq + len", but one byte before it.
Fix it so the 'ends_before' is evaluated properly.
This fixes a bug that results in error completions in the
kTLS HW offload flows.
Fixes:
ffbd9ca94e2e ("net/mlx5e: kTLS, Fix corner-case checks in TX resync flow")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Len Brown [Fri, 20 Mar 2020 03:24:17 +0000 (23:24 -0400)]
tools/power turbostat: Fix 32-bit capabilities warning
[ Upstream commit
fcaa681c03ea82193e60d7f2cdfd94fbbcd4cae9 ]
warning: `turbostat' uses 32-bit capabilities (legacy support in use)
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Len Brown [Thu, 19 Mar 2020 22:26:05 +0000 (18:26 -0400)]
tools/power turbostat: Fix missing SYS_LPI counter on some Chromebooks
[ Upstream commit
1f81c5efc020314b2db30d77efe228b7e117750d ]
Some Chromebook BIOS' do not export an ACPI LPIT, which is how
Linux finds the residency counter for CPU and SYSTEM low power states,
that is exports in /sys/devices/system/cpu/cpuidle/*residency_us
When these sysfs attributes are missing, check the debugfs attrubte
from the pmc_core driver, which accesses the same counter value.
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Len Brown [Thu, 19 Mar 2020 22:33:12 +0000 (18:33 -0400)]
tools/power turbostat: Fix gcc build warnings
[ Upstream commit
d8d005ba6afa502ca37ced5782f672c4d2fc1515 ]
Warning: ‘__builtin_strncpy’ specified bound 20 equals destination size
[-Wstringop-truncation]
reduce param to strncpy, to guarantee that a null byte is always copied
into destination buffer.
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
James Zhu [Wed, 18 Mar 2020 21:09:05 +0000 (17:09 -0400)]
drm/amdgpu: fix typo for vcn1 idle check
[ Upstream commit
acfc62dc68770aa665cc606891f6df7d6d1e52c0 ]
fix typo for vcn1 idle check
Signed-off-by: James Zhu <James.Zhu@amd.com>
Reviewed-by: Leo Liu <leo.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Eugeniy Paltsev [Mon, 16 Mar 2020 11:25:19 +0000 (14:25 +0300)]
initramfs: restore default compression behavior
[ Upstream commit
785d74ec3bbf26ac7f6e92e6e96a259aec0f107a ]
Even though INITRAMFS_SOURCE kconfig option isn't set in most of
defconfigs it is used (set) extensively by various build systems.
Commit
f26661e12765 ("initramfs: make initramfs compression choice
non-optional") has changed default compression mode. Previously we
compress initramfs using available compression algorithm. Now
we don't use any compression at all by default.
It significantly increases the image size in case of build system
chooses embedded initramfs. Initially I faced with this issue while
using buildroot.
As of today it's not possible to set preferred compression mode
in target defconfig as this option depends on INITRAMFS_SOURCE
being set. Modification of all build systems either doesn't look
like good option.
Let's instead rewrite initramfs compression mode choices list
the way that "INITRAMFS_COMPRESSION_NONE" will be the last option
in the list. In that case it will be chosen only if all other
options (which implements any compression) are not available.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Gerd Hoffmann [Fri, 13 Mar 2020 08:41:52 +0000 (09:41 +0100)]
drm/bochs: downgrade pci_request_region failure from error to warning
[ Upstream commit
8c34cd1a7f089dc03933289c5d4a4d1489549828 ]
Shutdown of firmware framebuffer has a bunch of problems. Because
of this the framebuffer region might still be reserved even after
drm_fb_helper_remove_conflicting_pci_framebuffers() returned.
Don't consider pci_request_region() failure for the framebuffer
region as fatal error to workaround this issue.
Reported-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20200313084152.2734-1-kraxel@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
Mario Kleiner [Fri, 28 Feb 2020 21:36:07 +0000 (22:36 +0100)]
drm/amd/display: Add link_rate quirk for Apple 15" MBP 2017
[ Upstream commit
dec9de2ada523b344eb2428abfedf9d6cd0a0029 ]
This fixes a problem found on the MacBookPro 2017 Retina panel:
The panel reports 10 bpc color depth in its EDID, and the
firmware chooses link settings at boot which support enough
bandwidth for 10 bpc (324000 kbit/sec aka LINK_RATE_RBR2
aka 0xc), but the DP_MAX_LINK_RATE dpcd register only reports
2.7 Gbps (multiplier value 0xa) as possible, in direct
contradiction of what the firmware successfully set up.
This restricts the panel to 8 bpc, not providing the full
color depth of the panel on Linux <= 5.5. Additionally, commit
'
4a8ca46bae8a ("drm/amd/display: Default max bpc to 16 for eDP")'
introduced into Linux 5.6-rc1 will unclamp panel depth to
its full 10 bpc, thereby requiring a eDP bandwidth for all
modes that exceeds the bandwidth available and causes all modes
to fail validation -> No modes for the laptop panel -> failure
to set any mode -> Panel goes dark.
This patch adds a quirk specific to the MBP 2017 15" Retina
panel to override reported max link rate to the correct maximum
of 0xc = LINK_RATE_RBR2 to fix the darkness and reduced display
precision.
Please apply for Linux 5.6+ to avoid regressing Apple MBP panel
support.
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Masahiro Yamada [Tue, 10 Mar 2020 10:12:49 +0000 (19:12 +0900)]
kconfig: introduce m32-flag and m64-flag
[ Upstream commit
8cc4fd73501d9f1370c3eebb70cfe8cc9e24062b ]
When a compiler supports multiple architectures, some compiler features
can be dependent on the target architecture.
This is typical for Clang, which supports multiple LLVM backends.
Even for GCC, we need to take care of biarch compiler cases.
It is not a problem when we evaluate cc-option in Makefiles because
cc-option is tested against the flag in question + $(KBUILD_CFLAGS).
The cc-option in Kconfig, on the other hand, does not accumulate
tested flags. Due to this simplification, it could potentially test
cc-option against a different target.
At first, Kconfig always evaluated cc-option against the host
architecture.
Since commit
e8de12fb7cde ("kbuild: Check for unknown options with
cc-option usage in Kconfig and clang"), in case of cross-compiling
with Clang, the target triple is correctly passed to Kconfig.
The case with biarch GCC (and native build with Clang) is still not
handled properly. We need to pass some flags to specify the target
machine bit.
Due to the design, all the macros in Kconfig are expanded in the
parse stage, where we do not know the target bit size yet.
For example, arch/x86/Kconfig allows a user to toggle CONFIG_64BIT.
If a compiler flag -foo depends on the machine bit, it must be tested
twice, one with -m32 and the other with -m64.
However, -m32/-m64 are not always recognized. So, this commits adds
m64-flag and m32-flag macros. They expand to -m32, -m64, respectively
if supported. Or, they expand to an empty string if unsupported.
The typical usage is like this:
config FOO
bool
default $(cc-option,$(m64-flag) -foo) if 64BIT
default $(cc-option,$(m32-flag) -foo)
This is clumsy, but there is no elegant way to handle this in the
current static macro expansion.
There was discussion for static functions vs dynamic functions.
The consensus was to go as far as possible with the static functions.
(https://lkml.org/lkml/2018/3/2/22)
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Tested-by: George Spelvin <lkml@sdf.org>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Prabhath Sajeepa [Mon, 9 Mar 2020 21:07:53 +0000 (15:07 -0600)]
nvme-rdma: Avoid double freeing of async event data
[ Upstream commit
9134ae2a2546cb96abddcd4469a79c77ee3a4480 ]
The timeout of identify cmd, which is invoked as part of admin queue
creation, can result in freeing of async event data both in
nvme_rdma_timeout handler and error handling path of
nvme_rdma_configure_admin queue thus causing NULL pointer reference.
Call Trace:
? nvme_rdma_setup_ctrl+0x223/0x800 [nvme_rdma]
nvme_rdma_create_ctrl+0x2ba/0x3f7 [nvme_rdma]
nvmf_dev_write+0xa54/0xcc6 [nvme_fabrics]
__vfs_write+0x1b/0x40
vfs_write+0xb2/0x1b0
ksys_write+0x61/0xd0
__x64_sys_write+0x1a/0x20
do_syscall_64+0x60/0x1e0
entry_SYSCALL_64_after_hwframe+0x44/0xa9
Reviewed-by: Roland Dreier <roland@purestorage.com>
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Prabhath Sajeepa <psajeepa@purestorage.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Greg Kroah-Hartman [Thu, 2 Apr 2020 13:11:03 +0000 (15:11 +0200)]
Linux 5.4.30
Madalin Bucur [Mon, 16 Mar 2020 12:05:58 +0000 (14:05 +0200)]
arm64: dts: ls1046ardb: set RGMII interfaces to RGMII_ID mode
commit
d79e9d7c1e4ba5f95f2ff3541880c40ea9722212 upstream.
The correct setting for the RGMII ports on LS1046ARDB is to
enable delay on both Rx and Tx so the interface mode used must
be PHY_INTERFACE_MODE_RGMII_ID.
Since commit
1b3047b5208a80 ("net: phy: realtek: add support for
configuring the RX delay on RTL8211F") the Realtek 8211F PHY driver
has control over the RGMII RX delay and it is disabling it for
RGMII_TXID. The LS1046ARDB uses two such PHYs in RGMII_ID mode but
in the device tree the mode was described as "rgmii".
Changing the phy-connection-type to "rgmii-id" to address the issue.
Fixes:
3fa395d2c48a ("arm64: dts: add LS1046A DPAA FMan nodes")
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Madalin Bucur [Mon, 16 Mar 2020 12:05:57 +0000 (14:05 +0200)]
arm64: dts: ls1043a-rdb: correct RGMII delay mode to rgmii-id
commit
4022d808c45277693ea86478fab1f081ebf997e8 upstream.
The correct setting for the RGMII ports on LS1043ARDB is to
enable delay on both Rx and Tx so the interface mode used must
be PHY_INTERFACE_MODE_RGMII_ID.
Since commit
1b3047b5208a80 ("net: phy: realtek: add support for
configuring the RX delay on RTL8211F") the Realtek 8211F PHY driver
has control over the RGMII RX delay and it is disabling it for
RGMII_TXID. The LS1043ARDB uses two such PHYs in RGMII_ID mode but
in the device tree the mode was described as "rgmii_txid".
This issue was not apparent at the time as the PHY driver took the
same action for RGMII_TXID and RGMII_ID back then but it became
visible (RX no longer working) after the above patch.
Changing the phy-connection-type to "rgmii-id" to address the issue.
Fixes:
bf02f2ffe59c ("arm64: dts: add LS1043A DPAA FMan support")
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Chen-Yu Tsai [Tue, 10 Mar 2020 17:47:07 +0000 (01:47 +0800)]
ARM: dts: sun8i: r40: Move AHCI device node based on address order
commit
fe3a04824f75786e39ed74e82fb6cb2534c95fe4 upstream.
When the AHCI device node was added, it was added in the wrong location
in the device tree file. The device nodes should be sorted by register
address.
Move the device node to before EHCI1, where it belongs.
Fixes:
41c64d3318aa ("ARM: dts: sun8i: r40: add sata node")
Acked-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Arthur Demchenkov [Sun, 8 Mar 2020 19:19:33 +0000 (22:19 +0300)]
ARM: dts: N900: fix onenand timings
commit
0c5220a3c1242c7a2451570ed5f5af69620aac75 upstream.
Commit
a758f50f10cf ("mtd: onenand: omap2: Configure driver from DT")
started using DT specified timings for GPMC, and as a result the
OneNAND stopped working on N900 as we had wrong values in the DT.
Fix by updating the values to bootloader timings that have been tested
to be working on Nokia N900 with OneNAND manufacturers: Samsung,
Numonyx.
Fixes:
a758f50f10cf ("mtd: onenand: omap2: Configure driver from DT")
Signed-off-by: Arthur Demchenkov <spinal.by@gmail.com>
Tested-by: Merlijn Wajer <merlijn@wizzup.org>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Marco Felsch [Thu, 27 Feb 2020 11:02:46 +0000 (12:02 +0100)]
ARM: dts: imx6: phycore-som: fix arm and soc minimum voltage
commit
636b45b8efa91db05553840b6c0120d6fa6b94fa upstream.
The current set minimum voltage of 730000µV seems to be wrong. I don't
know the document which specifies that but the imx6qdl datasheets says
that the minimum voltage should be 0.925V for VDD_ARM (LDO bypassed,
lowest opp) and 1.15V for VDD_SOC (LDO bypassed, lowest opp).
Fixes:
ddec5d1c0047 ("ARM: dts: imx6: Add initial support for phyCORE-i.MX 6 SOM")
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Nick Hudson [Thu, 12 Mar 2020 09:03:45 +0000 (09:03 +0000)]
ARM: bcm2835-rpi-zero-w: Add missing pinctrl name
commit
6687c201fdc3139315c2ea7ef96c157672805cdc upstream.
Define the sdhci pinctrl state as "default" so it gets applied
correctly and to match all other RPis.
Fixes:
2c7c040c73e9 ("ARM: dts: bcm2835: Add Raspberry Pi Zero W")
Signed-off-by: Nick Hudson <skrll@netbsd.org>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sungbo Eo [Sat, 21 Mar 2020 14:36:53 +0000 (23:36 +0900)]
ARM: dts: oxnas: Fix clear-mask property
commit
deeabb4c1341a12bf8b599e6a2f4cfa4fd74738c upstream.
Disable all rps-irq interrupts during driver initialization to prevent
an accidental interrupt on GIC.
Fixes:
84316f4ef141 ("ARM: boot: dts: Add Oxford Semiconductor OX810SE dtsi")
Fixes:
38d4a53733f5 ("ARM: dts: Add support for OX820 and Pogoplug V3")
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
disconnect3d [Mon, 9 Mar 2020 10:48:53 +0000 (11:48 +0100)]
perf map: Fix off by one in strncpy() size argument
commit
db2c549407d4a76563c579e4768f7d6d32afefba upstream.
This patch fixes an off-by-one error in strncpy size argument in
tools/perf/util/map.c. The issue is that in:
strncmp(filename, "/system/lib/", 11)
the passed string literal: "/system/lib/" has 12 bytes (without the NULL
byte) and the passed size argument is 11. As a result, the logic won't
match the ending "/" byte and will pass filepaths that are stored in
other directories e.g. "/system/libmalicious/bin" or just
"/system/libmalicious".
This functionality seems to be present only on Android. I assume the
/system/ directory is only writable by the root user, so I don't think
this bug has much (or any) security impact.
Fixes:
eca818369996 ("perf tools: Add automatic remapping of Android libraries")
Signed-off-by: disconnect3d <dominik.b.czarnota@gmail.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Changbin Du <changbin.du@intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: John Keeping <john@metanate.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Michael Lentine <mlentine@google.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Song Liu <songliubraving@fb.com>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lore.kernel.org/lkml/20200309104855.3775-1-dominik.b.czarnota@gmail.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ilie Halip [Thu, 19 Mar 2020 21:45:28 +0000 (23:45 +0200)]
arm64: alternative: fix build with clang integrated assembler
commit
6f5459da2b8736720afdbd67c4bd2d1edba7d0e3 upstream.
Building an arm64 defconfig with clang's integrated assembler, this error
occurs:
<instantiation>:2:2: error: unrecognized instruction mnemonic
_ASM_EXTABLE 9999b, 9f
^
arch/arm64/mm/cache.S:50:1: note: while in macro instantiation
user_alt 9f, "dc cvau, x4", "dc civac, x4", 0
^
While GNU as seems fine with case-sensitive macro instantiations, clang
doesn't, so use the actual macro name (_asm_extable) as in the rest of
the file.
Also checked that the generated assembly matches the GCC output.
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Tested-by: Nick Desaulniers <ndesaulniers@google.com>
Fixes:
290622efc76e ("arm64: fix "dc cvau" cache operation on errata-affected core")
Link: https://github.com/ClangBuiltLinux/linux/issues/924
Signed-off-by: Ilie Halip <ilie.halip@gmail.com>
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ilya Dryomov [Tue, 10 Mar 2020 15:19:01 +0000 (16:19 +0100)]
libceph: fix alloc_msg_with_page_vector() memory leaks
commit
e886274031200bb60965c1b9c49b7acda56a93bd upstream.
Make it so that CEPH_MSG_DATA_PAGES data item can own pages,
fixing a bunch of memory leaks for a page vector allocated in
alloc_msg_with_page_vector(). Currently, only watch-notify
messages trigger this allocation, and normally the page vector
is freed either in handle_watch_notify() or by the caller of
ceph_osdc_notify(). But if the message is freed before that
(e.g. if the session faults while reading in the message or
if the notify is stale), we leak the page vector.
This was supposed to be fixed by switching to a message-owned
pagelist, but that never happened.
Fixes:
1907920324f1 ("libceph: support for sending notifies")
Reported-by: Roman Penyaev <rpenyaev@suse.de>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Roman Penyaev <rpenyaev@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tony Lindgren [Fri, 21 Feb 2020 17:10:30 +0000 (09:10 -0800)]
clk: ti: am43xx: Fix clock parent for RTC clock
commit
5f3d9b07b9bb4679922f0b2e2baa770e74a6bbd3 upstream.
Currently enabling clkctrl clock on am4 can fail for RTC as the clock
parent is wrong for RTC.
Fixes:
76a1049b84dd ("clk: ti: am43xx: add new clkctrl data for am43xx")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lkml.kernel.org/r/20200221171030.39326-1-tony@atomide.com
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Leonard Crestez [Thu, 20 Feb 2020 16:29:33 +0000 (18:29 +0200)]
clk: imx: Align imx sc clock parent msg structs to 4
commit
8400ab8896324641243b57fc49b448023c07409a upstream.
The imx SC api strongly assumes that messages are composed out of
4-bytes words but some of our message structs have odd sizeofs.
This produces many oopses with CONFIG_KASAN=y.
Fix by marking with __aligned(4).
Fixes:
666aed2d13ee ("clk: imx: scu: add set parent support")
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Link: https://lkml.kernel.org/r/aad021e432b3062c142973d09b766656eec18fde.1582216144.git.leonard.crestez@nxp.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Leonard Crestez [Thu, 20 Feb 2020 16:29:32 +0000 (18:29 +0200)]
clk: imx: Align imx sc clock msg structs to 4
commit
a0ae04a25650fd51b7106e742d27333e502173c6 upstream.
The imx SC api strongly assumes that messages are composed out of
4-bytes words but some of our message structs have odd sizeofs.
This produces many oopses with CONFIG_KASAN=y.
Fix by marking with __aligned(4).
Fixes:
fe37b4820417 ("clk: imx: add scu clock common part")
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Link: https://lkml.kernel.org/r/10e97a04980d933b2cfecb6b124bf9046b6e4f16.1582216144.git.leonard.crestez@nxp.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Marek Vasut [Wed, 25 Mar 2020 14:25:47 +0000 (15:25 +0100)]
net: ks8851-ml: Fix IO operations, again
commit
8262e6f9b1034ede34548a04dec4c302d92c9497 upstream.
This patch reverts
58292104832f ("net: ks8851-ml: Fix 16-bit IO operation")
and
edacb098ea9c ("net: ks8851-ml: Fix 16-bit data access"), because it
turns out these were only necessary due to buggy hardware. This patch adds
a check for such a buggy hardware to prevent any such mistakes again.
While working further on the KS8851 driver, it came to light that the
KS8851-16MLL is capable of switching bus endianness by a hardware strap,
EESK pin. If this strap is incorrect, the IO accesses require such endian
swapping as is being reverted by this patch. Such swapping also impacts
the performance significantly.
Hence, in addition to removing it, detect that the hardware is broken,
report to user, and fail to bind with such hardware.
Fixes:
58292104832f ("net: ks8851-ml: Fix 16-bit IO operation")
Fixes:
edacb098ea9c ("net: ks8851-ml: Fix 16-bit data access")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Petr Stetiar <ynezz@true.cz>
Cc: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hans de Goede [Mon, 2 Mar 2020 11:12:25 +0000 (12:12 +0100)]
gpiolib: acpi: Add quirk to ignore EC wakeups on HP x2 10 CHT + AXP288 model
commit
0c625ccfe6f754d0896b8881f5c85bcb81699f1f upstream.
There are at least 3 models of the HP x2 10 models:
Bay Trail SoC + AXP288 PMIC
Cherry Trail SoC + AXP288 PMIC
Cherry Trail SoC + TI PMIC
Like on the other HP x2 10 models we need to ignore wakeup for ACPI GPIO
events on the external embedded-controller pin to avoid spurious wakeups
on the HP x2 10 CHT + AXP288 model too.
This commit adds an extra DMI based quirk for the HP x2 10 CHT + AXP288
model, ignoring wakeups for ACPI GPIO events on the EC interrupt pin
on this model. This fixes spurious wakeups from suspend on this model.
Fixes:
aa23ca3d98f7 ("gpiolib: acpi: Add honor_wakeup module-option + quirk mechanism")
Reported-and-tested-by: Marc Lehmann <schmorp@schmorp.de>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20200302111225.6641-4-hdegoede@redhat.com
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Greg Kroah-Hartman [Fri, 20 Mar 2020 16:22:58 +0000 (17:22 +0100)]
bpf: Explicitly memset some bpf info structures declared on the stack
commit
5c6f25887963f15492b604dd25cb149c501bbabf upstream.
Trying to initialize a structure with "= {};" will not always clean out
all padding locations in a structure. So be explicit and call memset to
initialize everything for a number of bpf information structures that
are then copied from userspace, sometimes from smaller memory locations
than the size of the structure.
Reported-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Yonghong Song <yhs@fb.com>
Link: https://lore.kernel.org/bpf/20200320162258.GA794295@kroah.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Greg Kroah-Hartman [Fri, 20 Mar 2020 09:48:13 +0000 (10:48 +0100)]
bpf: Explicitly memset the bpf_attr structure
commit
8096f229421f7b22433775e928d506f0342e5907 upstream.
For the bpf syscall, we are relying on the compiler to properly zero out
the bpf_attr union that we copy userspace data into. Unfortunately that
doesn't always work properly, padding and other oddities might not be
correctly zeroed, and in some tests odd things have been found when the
stack is pre-initialized to other values.
Fix this by explicitly memsetting the structure to 0 before using it.
Reported-by: Maciej Żenczykowski <maze@google.com>
Reported-by: John Stultz <john.stultz@linaro.org>
Reported-by: Alexander Potapenko <glider@google.com>
Reported-by: Alistair Delva <adelva@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Yonghong Song <yhs@fb.com>
Link: https://android-review.googlesource.com/c/kernel/common/+/1235490
Link: https://lore.kernel.org/bpf/20200320094813.GA421650@kroah.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Georg Müller [Mon, 3 Feb 2020 20:11:06 +0000 (21:11 +0100)]
platform/x86: pmc_atom: Add Lex 2I385SW to critclk_systems DMI table
commit
95b31e35239e5e1689e3d965d692a313c71bd8ab upstream.
The Lex 2I385SW board has two Intel I211 ethernet controllers. Without
this patch, only the first port is usable. The second port fails to
start with the following message:
igb: probe of 0000:02:00.0 failed with error -2
Fixes:
648e921888ad ("clk: x86: Stop marking clocks as CLK_IS_CRITICAL")
Tested-by: Georg Müller <georgmueller@gmx.net>
Signed-off-by: Georg Müller <georgmueller@gmx.net>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Eric Biggers [Sun, 22 Mar 2020 03:43:05 +0000 (20:43 -0700)]
vt: vt_ioctl: fix use-after-free in vt_in_use()
commit
7cf64b18b0b96e751178b8d0505d8466ff5a448f upstream.
vt_in_use() dereferences console_driver->ttys[i] without proper locking.
This is broken because the tty can be closed and freed concurrently.
We could fix this by using 'READ_ONCE(console_driver->ttys[i]) != NULL'
and skipping the check of tty_struct::count. But, looking at
console_driver->ttys[i] isn't really appropriate anyway because even if
it is NULL the tty can still be in the process of being closed.
Instead, fix it by making vt_in_use() require console_lock() and check
whether the vt is allocated and has port refcount > 1. This works since
following the patch "vt: vt_ioctl: fix VT_DISALLOCATE freeing in-use
virtual console" the port refcount is incremented while the vt is open.
Reproducer (very unreliable, but it worked for me after a few minutes):
#include <fcntl.h>
#include <linux/vt.h>
int main()
{
int fd, nproc;
struct vt_stat state;
char ttyname[16];
fd = open("/dev/tty10", O_RDONLY);
for (nproc = 1; nproc < 8; nproc *= 2)
fork();
for (;;) {
sprintf(ttyname, "/dev/tty%d", rand() % 8);
close(open(ttyname, O_RDONLY));
ioctl(fd, VT_GETSTATE, &state);
}
}
KASAN report:
BUG: KASAN: use-after-free in vt_in_use drivers/tty/vt/vt_ioctl.c:48 [inline]
BUG: KASAN: use-after-free in vt_ioctl+0x1ad3/0x1d70 drivers/tty/vt/vt_ioctl.c:657
Read of size 4 at addr
ffff888065722468 by task syz-vt2/132
CPU: 0 PID: 132 Comm: syz-vt2 Not tainted 5.6.0-rc5-00130-g089b6d3654916 #13
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS ?-20191223_100556-anatol 04/01/2014
Call Trace:
[...]
vt_in_use drivers/tty/vt/vt_ioctl.c:48 [inline]
vt_ioctl+0x1ad3/0x1d70 drivers/tty/vt/vt_ioctl.c:657
tty_ioctl+0x9db/0x11b0 drivers/tty/tty_io.c:2660
[...]
Allocated by task 136:
[...]
kzalloc include/linux/slab.h:669 [inline]
alloc_tty_struct+0x96/0x8a0 drivers/tty/tty_io.c:2982
tty_init_dev+0x23/0x350 drivers/tty/tty_io.c:1334
tty_open_by_driver drivers/tty/tty_io.c:1987 [inline]
tty_open+0x3ca/0xb30 drivers/tty/tty_io.c:2035
[...]
Freed by task 41:
[...]
kfree+0xbf/0x200 mm/slab.c:3757
free_tty_struct+0x8d/0xb0 drivers/tty/tty_io.c:177
release_one_tty+0x22d/0x2f0 drivers/tty/tty_io.c:1468
process_one_work+0x7f1/0x14b0 kernel/workqueue.c:2264
worker_thread+0x8b/0xc80 kernel/workqueue.c:2410
[...]
Fixes:
4001d7b7fc27 ("vt: push down the tty lock so we can see what is left to tackle")
Cc: <stable@vger.kernel.org> # v3.4+
Acked-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Link: https://lore.kernel.org/r/20200322034305.210082-3-ebiggers@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Eric Biggers [Sun, 22 Mar 2020 03:43:04 +0000 (20:43 -0700)]
vt: vt_ioctl: fix VT_DISALLOCATE freeing in-use virtual console
commit
ca4463bf8438b403596edd0ec961ca0d4fbe0220 upstream.
The VT_DISALLOCATE ioctl can free a virtual console while tty_release()
is still running, causing a use-after-free in con_shutdown(). This
occurs because VT_DISALLOCATE considers a virtual console's
'struct vc_data' to be unused as soon as the corresponding tty's
refcount hits 0. But actually it may be still being closed.
Fix this by making vc_data be reference-counted via the embedded
'struct tty_port'. A newly allocated virtual console has refcount 1.
Opening it for the first time increments the refcount to 2. Closing it
for the last time decrements the refcount (in tty_operations::cleanup()
so that it happens late enough), as does VT_DISALLOCATE.
Reproducer:
#include <fcntl.h>
#include <linux/vt.h>
#include <sys/ioctl.h>
#include <unistd.h>
int main()
{
if (fork()) {
for (;;)
close(open("/dev/tty5", O_RDWR));
} else {
int fd = open("/dev/tty10", O_RDWR);
for (;;)
ioctl(fd, VT_DISALLOCATE, 5);
}
}
KASAN report:
BUG: KASAN: use-after-free in con_shutdown+0x76/0x80 drivers/tty/vt/vt.c:3278
Write of size 8 at addr
ffff88806a4ec108 by task syz_vt/129
CPU: 0 PID: 129 Comm: syz_vt Not tainted 5.6.0-rc2 #11
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS ?-20191223_100556-anatol 04/01/2014
Call Trace:
[...]
con_shutdown+0x76/0x80 drivers/tty/vt/vt.c:3278
release_tty+0xa8/0x410 drivers/tty/tty_io.c:1514
tty_release_struct+0x34/0x50 drivers/tty/tty_io.c:1629
tty_release+0x984/0xed0 drivers/tty/tty_io.c:1789
[...]
Allocated by task 129:
[...]
kzalloc include/linux/slab.h:669 [inline]
vc_allocate drivers/tty/vt/vt.c:1085 [inline]
vc_allocate+0x1ac/0x680 drivers/tty/vt/vt.c:1066
con_install+0x4d/0x3f0 drivers/tty/vt/vt.c:3229
tty_driver_install_tty drivers/tty/tty_io.c:1228 [inline]
tty_init_dev+0x94/0x350 drivers/tty/tty_io.c:1341
tty_open_by_driver drivers/tty/tty_io.c:1987 [inline]
tty_open+0x3ca/0xb30 drivers/tty/tty_io.c:2035
[...]
Freed by task 130:
[...]
kfree+0xbf/0x1e0 mm/slab.c:3757
vt_disallocate drivers/tty/vt/vt_ioctl.c:300 [inline]
vt_ioctl+0x16dc/0x1e30 drivers/tty/vt/vt_ioctl.c:818
tty_ioctl+0x9db/0x11b0 drivers/tty/tty_io.c:2660
[...]
Fixes:
4001d7b7fc27 ("vt: push down the tty lock so we can see what is left to tackle")
Cc: <stable@vger.kernel.org> # v3.4+
Reported-by: syzbot+522643ab5729b0421998@syzkaller.appspotmail.com
Acked-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Link: https://lore.kernel.org/r/20200322034305.210082-2-ebiggers@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Eric Biggers [Mon, 24 Feb 2020 08:03:26 +0000 (00:03 -0800)]
vt: vt_ioctl: remove unnecessary console allocation checks
commit
1aa6e058dd6cd04471b1f21298270014daf48ac9 upstream.
The vc_cons_allocated() checks in vt_ioctl() and vt_compat_ioctl() are
unnecessary because they can only be reached by calling ioctl() on an
open tty, which implies the corresponding virtual console is allocated.
And even if the virtual console *could* be freed concurrently, then
these checks would be broken since they aren't done under console_lock,
and the vc_data is dereferenced before them anyway.
So, remove these unneeded checks to avoid confusion.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Link: https://lore.kernel.org/r/20200224080326.295046-1-ebiggers@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jiri Slaby [Wed, 19 Feb 2020 07:39:48 +0000 (08:39 +0100)]
vt: switch vt_dont_switch to bool
commit
f400991bf872debffb01c46da882dc97d7e3248e upstream.
vt_dont_switch is pure boolean, no need for whole char.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20200219073951.16151-6-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jiri Slaby [Wed, 19 Feb 2020 07:39:44 +0000 (08:39 +0100)]
vt: ioctl, switch VT_IS_IN_USE and VT_BUSY to inlines
commit
e587e8f17433ddb26954f0edf5b2f95c42155ae9 upstream.
These two were macros. Switch them to static inlines, so that it's more
understandable what they are doing.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20200219073951.16151-2-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jiri Slaby [Wed, 19 Feb 2020 07:39:43 +0000 (08:39 +0100)]
vt: selection, introduce vc_is_sel
commit
dce05aa6eec977f1472abed95ccd71276b9a3864 upstream.
Avoid global variables (namely sel_cons) by introducing vc_is_sel. It
checks whether the parameter is the current selection console. This will
help putting sel_cons to a struct later.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20200219073951.16151-1-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Lanqing Liu [Mon, 16 Mar 2020 03:13:33 +0000 (11:13 +0800)]
serial: sprd: Fix a dereference warning
commit
efc176929a3505a30c3993ddd393b40893649bd2 upstream.
We should validate if the 'sup' is NULL or not before freeing DMA
memory, to fix below warning.
"drivers/tty/serial/sprd_serial.c:1141 sprd_remove()
error: we previously assumed 'sup' could be null (see line 1132)"
Fixes:
f4487db58eb7 ("serial: sprd: Add DMA mode support")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Lanqing Liu <liuhhome@gmail.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/e2bd92691538e95b04a2c2a728f3292e1617018f.1584325957.git.liuhhome@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johannes Berg [Sun, 29 Mar 2020 20:50:06 +0000 (22:50 +0200)]
mac80211: fix authentication with iwlwifi/mvm
commit
be8c827f50a0bcd56361b31ada11dc0a3c2fd240 upstream.
The original patch didn't copy the ieee80211_is_data() condition
because on most drivers the management frames don't go through
this path. However, they do on iwlwifi/mvm, so we do need to keep
the condition here.
Cc: stable@vger.kernel.org
Fixes:
ce2e1ca70307 ("mac80211: Check port authorization in the ieee80211_tx_dequeue() case")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: Woody Suwalski <terraluna977@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jouni Malinen [Thu, 26 Mar 2020 14:51:34 +0000 (15:51 +0100)]
mac80211: Check port authorization in the ieee80211_tx_dequeue() case
commit
ce2e1ca703071723ca2dd94d492a5ab6d15050da upstream.
mac80211 used to check port authorization in the Data frame enqueue case
when going through start_xmit(). However, that authorization status may
change while the frame is waiting in a queue. Add a similar check in the
dequeue case to avoid sending previously accepted frames after
authorization change. This provides additional protection against
potential leaking of frames after a station has been disconnected and
the keys for it are being removed.
Cc: stable@vger.kernel.org
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Link: https://lore.kernel.org/r/20200326155133.ced84317ea29.I34d4c47cd8cc8a4042b38a76f16a601fbcbfd9b3@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Greg Kroah-Hartman [Wed, 1 Apr 2020 09:02:18 +0000 (11:02 +0200)]
Linux 5.4.29
Pablo Neira Ayuso [Wed, 25 Mar 2020 12:47:18 +0000 (13:47 +0100)]
net: Fix CONFIG_NET_CLS_ACT=n and CONFIG_NFT_FWD_NETDEV={y, m} build
commit
2c64605b590edadb3fb46d1ec6badb49e940b479 upstream.
net/netfilter/nft_fwd_netdev.c: In function ‘nft_fwd_netdev_eval’:
net/netfilter/nft_fwd_netdev.c:32:10: error: ‘struct sk_buff’ has no member named ‘tc_redirected’
pkt->skb->tc_redirected = 1;
^~
net/netfilter/nft_fwd_netdev.c:33:10: error: ‘struct sk_buff’ has no member named ‘tc_from_ingress’
pkt->skb->tc_from_ingress = 1;
^~
To avoid a direct dependency with tc actions from netfilter, wrap the
redirect bits around CONFIG_NET_REDIRECT and move helpers to
include/linux/skbuff.h. Turn on this toggle from the ifb driver, the
only existing client of these bits in the tree.
This patch adds skb_set_redirected() that sets on the redirected bit
on the skbuff, it specifies if the packet was redirect from ingress
and resets the timestamp (timestamp reset was originally missing in the
netfilter bugfix).
Fixes:
bcfabee1afd99484 ("netfilter: nft_fwd_netdev: allow to redirect to ifb via ingress")
Reported-by: noreply@ellerman.id.au
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dafna Hirschfeld [Wed, 19 Feb 2020 15:25:54 +0000 (16:25 +0100)]
media: v4l2-core: fix a use-after-free bug of sd->devnode
commit
6990570f7e0a6078e11b9c5dc13f4b6e3f49a398 upstream.
sd->devnode is released after calling
v4l2_subdev_release. Therefore it should be set
to NULL so that the subdev won't hold a pointer
to a released object. This fixes a reference
after free bug in function
v4l2_device_unregister_subdev
Fixes:
0e43734d4c46e ("media: v4l2-subdev: add release() internal op")
Cc: stable@vger.kernel.org
Signed-off-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
Reviewed-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan Hovold [Fri, 3 Jan 2020 16:35:11 +0000 (17:35 +0100)]
media: xirlink_cit: add missing descriptor sanity checks
commit
a246b4d547708f33ff4d4b9a7a5dbac741dc89d8 upstream.
Make sure to check that we have two alternate settings and at least one
endpoint before accessing the second altsetting structure and
dereferencing the endpoint arrays.
This specifically avoids dereferencing NULL-pointers or corrupting
memory when a device does not have the expected descriptors.
Note that the sanity check in cit_get_packet_size() is not redundant as
the driver is mixing looking up altsettings by index and by number,
which may not coincide.
Fixes:
659fefa0eb17 ("V4L/DVB: gspca_xirlink_cit: Add support for camera with a bcd version of 0.01")
Fixes:
59f8b0bf3c12 ("V4L/DVB: gspca_xirlink_cit: support bandwidth changing for devices with 1 alt setting")
Cc: stable <stable@vger.kernel.org> # 2.6.37
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan Hovold [Fri, 3 Jan 2020 16:35:10 +0000 (17:35 +0100)]
media: stv06xx: add missing descriptor sanity checks
commit
485b06aadb933190f4bc44e006076bc27a23f205 upstream.
Make sure to check that we have two alternate settings and at least one
endpoint before accessing the second altsetting structure and
dereferencing the endpoint arrays.
This specifically avoids dereferencing NULL-pointers or corrupting
memory when a device does not have the expected descriptors.
Note that the sanity checks in stv06xx_start() and pb0100_start() are
not redundant as the driver is mixing looking up altsettings by index
and by number, which may not coincide.
Fixes:
8668d504d72c ("V4L/DVB (12082): gspca_stv06xx: Add support for st6422 bridge and sensor")
Fixes:
c0b33bdc5b8d ("[media] gspca-stv06xx: support bandwidth changing")
Cc: stable <stable@vger.kernel.org> # 2.6.31
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan Hovold [Fri, 3 Jan 2020 16:35:12 +0000 (17:35 +0100)]
media: dib0700: fix rc endpoint lookup
commit
f52981019ad8d6718de79b425a574c6bddf81f7c upstream.
Make sure to use the current alternate setting when verifying the
interface descriptors to avoid submitting an URB to an invalid endpoint.
Failing to do so could cause the driver to misbehave or trigger a WARN()
in usb_submit_urb() that kernels with panic_on_warn set would choke on.
Fixes:
c4018fa2e4c0 ("[media] dib0700: fix RC support on Hauppauge Nova-TD")
Cc: stable <stable@vger.kernel.org> # 3.16
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan Hovold [Fri, 3 Jan 2020 16:35:09 +0000 (17:35 +0100)]
media: ov519: add missing endpoint sanity checks
commit
998912346c0da53a6dbb71fab3a138586b596b30 upstream.
Make sure to check that we have at least one endpoint before accessing
the endpoint array to avoid dereferencing a NULL-pointer on stream
start.
Note that these sanity checks are not redundant as the driver is mixing
looking up altsettings by index and by number, which need not coincide.
Fixes:
1876bb923c98 ("V4L/DVB (12079): gspca_ov519: add support for the ov511 bridge")
Fixes:
b282d87332f5 ("V4L/DVB (12080): gspca_ov519: Fix ov518+ with OV7620AE (Trust spacecam 320)")
Cc: stable <stable@vger.kernel.org> # 2.6.31
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Eric Biggers [Sun, 8 Mar 2020 02:38:49 +0000 (18:38 -0800)]
libfs: fix infoleak in simple_attr_read()
commit
a65cab7d7f05c2061a3e2490257d3086ff3202c6 upstream.
Reading from a debugfs file at a nonzero position, without first reading
at position 0, leaks uninitialized memory to userspace.
It's a bit tricky to do this, since lseek() and pread() aren't allowed
on these files, and write() doesn't update the position on them. But
writing to them with splice() *does* update the position:
#define _GNU_SOURCE 1
#include <fcntl.h>
#include <stdio.h>
#include <unistd.h>
int main()
{
int pipes[2], fd, n, i;
char buf[32];
pipe(pipes);
write(pipes[1], "0", 1);
fd = open("/sys/kernel/debug/fault_around_bytes", O_RDWR);
splice(pipes[0], NULL, fd, NULL, 1, 0);
n = read(fd, buf, sizeof(buf));
for (i = 0; i < n; i++)
printf("%02x", buf[i]);
printf("\n");
}
Output:
5a5a5a5a5a5a5a5a5a5a5a5a5a5a5a5a5a5a5a5a5a5a5a30
Fix the infoleak by making simple_attr_read() always fill
simple_attr::get_buf if it hasn't been filled yet.
Reported-by: syzbot+fcab69d1ada3e8d6f06b@syzkaller.appspotmail.com
Reported-by: Alexander Potapenko <glider@google.com>
Fixes:
acaefc25d21f ("[PATCH] libfs: add simple attribute files")
Cc: stable@vger.kernel.org
Signed-off-by: Eric Biggers <ebiggers@google.com>
Acked-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20200308023849.988264-1-ebiggers@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Kai-Heng Feng [Thu, 27 Feb 2020 12:28:22 +0000 (20:28 +0800)]
ahci: Add Intel Comet Lake H RAID PCI ID
commit
32d2545462c6cede998267b86e57cda5d1dc2225 upstream.
Add the PCI ID to the driver list to support this new device.
Cc: stable@vger.kernel.org
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Qiujun Huang [Thu, 26 Mar 2020 13:18:50 +0000 (21:18 +0800)]
staging: wlan-ng: fix use-after-free Read in hfa384x_usbin_callback
commit
1165dd73e811a07d947aee218510571f516081f6 upstream.
We can't handle the case length > WLAN_DATA_MAXLEN.
Because the size of rxfrm->data is WLAN_DATA_MAXLEN(2312), and we can't
read more than that.
Thanks-to: Hillf Danton <hdanton@sina.com>
Reported-and-tested-by: syzbot+7d42d68643a35f71ac8a@syzkaller.appspotmail.com
Signed-off-by: Qiujun Huang <hqjagain@gmail.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200326131850.17711-1-hqjagain@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Qiujun Huang [Wed, 25 Mar 2020 07:06:46 +0000 (15:06 +0800)]
staging: wlan-ng: fix ODEBUG bug in prism2sta_disconnect_usb
commit
a1f165a6b738f0c9d744bad4af7a53909278f5fc upstream.
We should cancel hw->usb_work before kfree(hw).
Reported-by: syzbot+6d2e7f6fa90e27be9d62@syzkaller.appspotmail.com
Signed-off-by: Qiujun Huang <hqjagain@gmail.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/1585120006-30042-1-git-send-email-hqjagain@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Larry Finger [Sat, 21 Mar 2020 18:00:11 +0000 (13:00 -0500)]
staging: rtl8188eu: Add ASUS USB-N10 Nano B1 to device table
commit
38ef48f7d4b7342f145a1b4f96023bde99aeb245 upstream.
The ASUS USB-N10 Nano B1 has been reported as a new RTL8188EU device.
Add it to the device tables.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Reported-by: kovi <zraetn@gmail.com>
Cc: Stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200321180011.26153-1-Larry.Finger@lwfinger.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dan Carpenter [Mon, 24 Feb 2020 10:33:25 +0000 (13:33 +0300)]
staging: kpc2000: prevent underflow in cpld_reconfigure()
commit
72db61d7d17a475d3cc9de1a7c871d518fcd82f0 upstream.
This function should not allow negative values of "wr_val". If
negatives are allowed then capping the upper bound at 7 is
meaningless. Let's make it unsigned.
Fixes:
7dc7967fc39a ("staging: kpc2000: add initial set of Daktronics drivers")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200224103325.hrxdnaeqsthplu42@kili.mountain
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan Hovold [Mon, 13 Jan 2020 17:18:18 +0000 (18:18 +0100)]
media: usbtv: fix control-message timeouts
commit
536f561d871c5781bc33d26d415685211b94032e upstream.
The driver was issuing synchronous uninterruptible control requests
without using a timeout. This could lead to the driver hanging on
various user requests due to a malfunctioning (or malicious) device
until the device is physically disconnected.
The USB upper limit of five seconds per request should be more than
enough.
Fixes:
f3d27f34fdd7 ("[media] usbtv: Add driver for Fushicai USBTV007 video frame grabber")
Fixes:
c53a846c48f2 ("[media] usbtv: add video controls")
Cc: stable <stable@vger.kernel.org> # 3.11
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Lubomir Rintel <lkundrak@v3.sk>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan Hovold [Fri, 3 Jan 2020 16:35:08 +0000 (17:35 +0100)]
media: flexcop-usb: fix endpoint sanity check
commit
bca243b1ce0e46be26f7c63b5591dfbb41f558e5 upstream.
commit
1b976fc6d684 ("media: b2c2-flexcop-usb: add sanity checking") added
an endpoint sanity check to address a NULL-pointer dereference on probe.
Unfortunately the check was done on the current altsetting which was later
changed.
Fix this by moving the sanity check to after the altsetting is changed.
Fixes:
1b976fc6d684 ("media: b2c2-flexcop-usb: add sanity checking")
Cc: Oliver Neukum <oneukum@suse.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mans Rullgard [Mon, 16 Mar 2020 21:11:35 +0000 (16:11 -0500)]
usb: musb: fix crash with highmen PIO and usbmon
commit
52974d94a206ce428d9d9b6eaa208238024be82a upstream.
When handling a PIO bulk transfer with highmem buffer, a temporary
mapping is assigned to urb->transfer_buffer. After the transfer is
complete, an invalid address is left behind in this pointer. This is
not ordinarily a problem since nothing touches that buffer before the
urb is released. However, when usbmon is active, usbmon_urb_complete()
calls (indirectly) mon_bin_get_data() which does access the transfer
buffer if it is set. To prevent an invalid memory access here, reset
urb->transfer_buffer to NULL when finished (musb_host_rx()), or do not
set it at all (musb_host_tx()).
Fixes:
8e8a55165469 ("usb: musb: host: Handle highmem in PIO mode")
Signed-off-by: Mans Rullgard <mans@mansr.com>
Cc: stable@vger.kernel.org
Signed-off-by: Bin Liu <b-liu@ti.com>
Link: https://lore.kernel.org/r/20200316211136.2274-8-b-liu@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Qiujun Huang [Wed, 25 Mar 2020 07:52:37 +0000 (15:52 +0800)]
USB: serial: io_edgeport: fix slab-out-of-bounds read in edge_interrupt_callback
commit
57aa9f294b09463492f604feaa5cc719beaace32 upstream.
Fix slab-out-of-bounds read in the interrupt-URB completion handler.
The boundary condition should be (length - 1) as we access
data[position + 1].
Reported-and-tested-by: syzbot+37ba33391ad5f3935bbd@syzkaller.appspotmail.com
Signed-off-by: Qiujun Huang <hqjagain@gmail.com>
Fixes:
1da177e4c3f4 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Matthias Reichl [Fri, 27 Mar 2020 15:03:50 +0000 (16:03 +0100)]
USB: cdc-acm: restore capability check order
commit
62d65bdd9d05158aa2547f8ef72375535f3bc6e3 upstream.
commit
b401f8c4f492c ("USB: cdc-acm: fix rounding error in TIOCSSERIAL")
introduced a regression by changing the order of capability and close
settings change checks. When running with CAP_SYS_ADMIN setting the
close settings to the values already set resulted in -EOPNOTSUPP.
Fix this by changing the check order back to how it was before.
Fixes:
b401f8c4f492c ("USB: cdc-acm: fix rounding error in TIOCSSERIAL")
Cc: Anthony Mallet <anthony.mallet@laas.fr>
Cc: stable <stable@vger.kernel.org>
Cc: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Matthias Reichl <hias@horus.com>
Link: https://lore.kernel.org/r/20200327150350.3657-1-hias@horus.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pawel Dembicki [Wed, 25 Mar 2020 05:44:19 +0000 (06:44 +0100)]
USB: serial: option: add Wistron Neweb D19Q1
commit
dfee7e2f478346b12ea651d5c28b069f6a4af563 upstream.
This modem is embedded on dlink dwr-960 router.
The oem configuration states:
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=480 MxCh= 0
D: Ver= 2.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1435 ProdID=d191 Rev=ff.ff
S: Manufacturer=Android
S: Product=Android
S: SerialNumber=
0123456789ABCDEF
C:* #Ifs= 6 Cfg#= 1 Atr=80 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none)
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none)
E: Ad=84(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none)
E: Ad=86(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
E: Ad=88(I) Atr=03(Int.) MxPS= 8 Ivl=32ms
E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 5 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=(none)
E: Ad=89(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=125us
Tested on openwrt distribution
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pawel Dembicki [Wed, 25 Mar 2020 05:44:18 +0000 (06:44 +0100)]
USB: serial: option: add BroadMobi BM806U
commit
6cb2669cb97fc4fdf526127159ac59caae052247 upstream.
BroadMobi BM806U is an Qualcomm MDM9225 based 3G/4G modem.
Tested hardware BM806U is mounted on D-Link DWR-921-C3 router.
T: Bus=01 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 2 Spd=480 MxCh= 0
D: Ver= 2.01 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=2020 ProdID=2033 Rev= 2.28
S: Manufacturer=Mobile Connect
S: Product=Mobile Connect
S: SerialNumber=
f842866cfd5a
C:* #Ifs= 5 Cfg#= 1 Atr=80 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=83(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=85(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=87(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
E: Ad=89(I) Atr=03(Int.) MxPS= 8 Ivl=32ms
E: Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
Co-developed-by: Cezary Jackiewicz <cezary@eko.one.pl>
Signed-off-by: Cezary Jackiewicz <cezary@eko.one.pl>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pawel Dembicki [Wed, 25 Mar 2020 05:44:17 +0000 (06:44 +0100)]
USB: serial: option: add support for ASKEY WWHC050
commit
007d20dca2376a751b1dad03442f118438b7e65e upstream.
ASKEY WWHC050 is a mcie LTE modem.
The oem configuration states:
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=480 MxCh= 0
D: Ver= 2.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1690 ProdID=7588 Rev=ff.ff
S: Manufacturer=Android
S: Product=Android
S: SerialNumber=
813f0eef6e6e
C:* #Ifs= 6 Cfg#= 1 Atr=80 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none)
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=84(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=86(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
E: Ad=88(I) Atr=03(Int.) MxPS= 8 Ivl=32ms
E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 5 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=(none)
E: Ad=89(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=125us
Tested on openwrt distribution.
Co-developed-by: Cezary Jackiewicz <cezary@eko.one.pl>
Signed-off-by: Cezary Jackiewicz <cezary@eko.one.pl>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Daniel Borkmann [Mon, 30 Mar 2020 16:03:22 +0000 (18:03 +0200)]
bpf: Undo incorrect __reg_bound_offset32 handling
commit
f2d67fec0b43edce8c416101cdc52e71145b5fef upstream.
Anatoly has been fuzzing with kBdysch harness and reported a hang in
one of the outcomes:
0: (b7) r0 =
808464432
1: (7f) r0 >>= r0
2: (14) w0 -=
808464432
3: (07) r0 +=
808464432
4: (b7) r1 =
808464432
5: (de) if w1 s<= w0 goto pc+0
R0_w=invP(id=0,umin_value=
808464432,umax_value=
5103431727,var_off=(0x30303020;0x10000001f)) R1_w=invP808464432 R10=fp0
6: (07) r0 += -
2144337872
7: (14) w0 -= -
1607454672
8: (25) if r0 > 0x30303030 goto pc+0
R0_w=invP(id=0,umin_value=
271581184,umax_value=
271581311,var_off=(0x10300000;0x7f)) R1_w=invP808464432 R10=fp0
9: (76) if w0 s>= 0x303030 goto pc+2
12: (95) exit
from 8 to 9: safe
from 5 to 6: R0_w=invP(id=0,umin_value=
808464432,umax_value=
5103431727,var_off=(0x30303020;0x10000001f)) R1_w=invP808464432 R10=fp0
6: (07) r0 += -
2144337872
7: (14) w0 -= -
1607454672
8: (25) if r0 > 0x30303030 goto pc+0
R0_w=invP(id=0,umin_value=
271581184,umax_value=
271581311,var_off=(0x10300000;0x7f)) R1_w=invP808464432 R10=fp0
9: safe
from 8 to 9: safe
verification time 589 usec
stack depth 0
processed 17 insns (limit 1000000) [...]
The underlying program was xlated as follows:
# bpftool p d x i 9
0: (b7) r0 =
808464432
1: (7f) r0 >>= r0
2: (14) w0 -=
808464432
3: (07) r0 +=
808464432
4: (b7) r1 =
808464432
5: (de) if w1 s<= w0 goto pc+0
6: (07) r0 += -
2144337872
7: (14) w0 -= -
1607454672
8: (25) if r0 > 0x30303030 goto pc+0
9: (76) if w0 s>= 0x303030 goto pc+2
10: (05) goto pc-1
11: (05) goto pc-1
12: (95) exit
The verifier rewrote original instructions it recognized as dead code with
'goto pc-1', but reality differs from verifier simulation in that we're
actually able to trigger a hang due to hitting the 'goto pc-1' instructions.
Taking different examples to make the issue more obvious: in this example
we're probing bounds on a completely unknown scalar variable in r1:
[...]
5: R0_w=inv1 R1_w=inv(id=0) R10=fp0
5: (18) r2 = 0x4000000000
7: R0_w=inv1 R1_w=inv(id=0) R2_w=inv274877906944 R10=fp0
7: (18) r3 = 0x2000000000
9: R0_w=inv1 R1_w=inv(id=0) R2_w=inv274877906944 R3_w=inv137438953472 R10=fp0
9: (18) r4 = 0x400
11: R0_w=inv1 R1_w=inv(id=0) R2_w=inv274877906944 R3_w=inv137438953472 R4_w=inv1024 R10=fp0
11: (18) r5 = 0x200
13: R0_w=inv1 R1_w=inv(id=0) R2_w=inv274877906944 R3_w=inv137438953472 R4_w=inv1024 R5_w=inv512 R10=fp0
13: (2d) if r1 > r2 goto pc+4
R0_w=inv1 R1_w=inv(id=0,umax_value=
274877906944,var_off=(0x0; 0x7fffffffff)) R2_w=inv274877906944 R3_w=inv137438953472 R4_w=inv1024 R5_w=inv512 R10=fp0
14: R0_w=inv1 R1_w=inv(id=0,umax_value=
274877906944,var_off=(0x0; 0x7fffffffff)) R2_w=inv274877906944 R3_w=inv137438953472 R4_w=inv1024 R5_w=inv512 R10=fp0
14: (ad) if r1 < r3 goto pc+3
R0_w=inv1 R1_w=inv(id=0,umin_value=
137438953472,umax_value=
274877906944,var_off=(0x0; 0x7fffffffff)) R2_w=inv274877906944 R3_w=inv137438953472 R4_w=inv1024 R5_w=inv512 R10=fp0
15: R0=inv1 R1=inv(id=0,umin_value=
137438953472,umax_value=
274877906944,var_off=(0x0; 0x7fffffffff)) R2=inv274877906944 R3=inv137438953472 R4=inv1024 R5=inv512 R10=fp0
15: (2e) if w1 > w4 goto pc+2
R0=inv1 R1=inv(id=0,umin_value=
137438953472,umax_value=
274877906944,var_off=(0x0; 0x7f00000000)) R2=inv274877906944 R3=inv137438953472 R4=inv1024 R5=inv512 R10=fp0
16: R0=inv1 R1=inv(id=0,umin_value=
137438953472,umax_value=
274877906944,var_off=(0x0; 0x7f00000000)) R2=inv274877906944 R3=inv137438953472 R4=inv1024 R5=inv512 R10=fp0
16: (ae) if w1 < w5 goto pc+1
R0=inv1 R1=inv(id=0,umin_value=
137438953472,umax_value=
274877906944,var_off=(0x0; 0x7f00000000)) R2=inv274877906944 R3=inv137438953472 R4=inv1024 R5=inv512 R10=fp0
[...]
We're first probing lower/upper bounds via jmp64, later we do a similar
check via jmp32 and examine the resulting var_off there. After fall-through
in insn 14, we get the following bounded r1 with 0x7fffffffff unknown marked
bits in the variable section.
Thus, after knowing r1 <= 0x4000000000 and r1 >= 0x2000000000:
max: 0b100000000000000000000000000000000000000 / 0x4000000000
var: 0b111111111111111111111111111111111111111 / 0x7fffffffff
min: 0b010000000000000000000000000000000000000 / 0x2000000000
Now, in insn 15 and 16, we perform a similar probe with lower/upper bounds
in jmp32.
Thus, after knowing r1 <= 0x4000000000 and r1 >= 0x2000000000 and
w1 <= 0x400 and w1 >= 0x200:
max: 0b100000000000000000000000000000000000000 / 0x4000000000
var: 0b111111100000000000000000000000000000000 / 0x7f00000000
min: 0b010000000000000000000000000000000000000 / 0x2000000000
The lower/upper bounds haven't changed since they have high bits set in
u64 space and the jmp32 tests can only refine bounds in the low bits.
However, for the var part the expectation would have been 0x7f000007ff
or something less precise up to 0x7fffffffff. A outcome of 0x7f00000000
is not correct since it would contradict the earlier probed bounds
where we know that the result should have been in [0x200,0x400] in u32
space. Therefore, tests with such info will lead to wrong verifier
assumptions later on like falsely predicting conditional jumps to be
always taken, etc.
The issue here is that __reg_bound_offset32()'s implementation from
commit
581738a681b6 ("bpf: Provide better register bounds after jmp32
instructions") makes an incorrect range assumption:
static void __reg_bound_offset32(struct bpf_reg_state *reg)
{
u64 mask = 0xffffFFFF;
struct tnum range = tnum_range(reg->umin_value & mask,
reg->umax_value & mask);
struct tnum lo32 = tnum_cast(reg->var_off, 4);
struct tnum hi32 = tnum_lshift(tnum_rshift(reg->var_off, 32), 32);
reg->var_off = tnum_or(hi32, tnum_intersect(lo32, range));
}
In the above walk-through example, __reg_bound_offset32() as-is chose
a range after masking with 0xffffffff of [0x0,0x0] since umin:0x2000000000
and umax:0x4000000000 and therefore the lo32 part was clamped to 0x0 as
well. However, in the umin:0x2000000000 and umax:0x4000000000 range above
we'd end up with an actual possible interval of [0x0,0xffffffff] for u32
space instead.
In case of the original reproducer, the situation looked as follows at
insn 5 for r0:
[...]
5: R0_w=invP(id=0,umin_value=
808464432,umax_value=
5103431727,var_off=(0x0; 0x1ffffffff)) R1_w=invP808464432 R10=fp0
0x30303030 0x13030302f
5: (de) if w1 s<= w0 goto pc+0
R0_w=invP(id=0,umin_value=
808464432,umax_value=
5103431727,var_off=(0x30303020; 0x10000001f)) R1_w=invP808464432 R10=fp0
0x30303030 0x13030302f
[...]
After the fall-through, we similarly forced the var_off result into
the wrong range [0x30303030,0x3030302f] suggesting later on that fixed
bits must only be of 0x30303020 with 0x10000001f unknowns whereas such
assumption can only be made when both bounds in hi32 range match.
Originally, I was thinking to fix this by moving reg into a temp reg and
use proper coerce_reg_to_size() helper on the temp reg where we can then
based on that define the range tnum for later intersection:
static void __reg_bound_offset32(struct bpf_reg_state *reg)
{
struct bpf_reg_state tmp = *reg;
struct tnum lo32, hi32, range;
coerce_reg_to_size(&tmp, 4);
range = tnum_range(tmp.umin_value, tmp.umax_value);
lo32 = tnum_cast(reg->var_off, 4);
hi32 = tnum_lshift(tnum_rshift(reg->var_off, 32), 32);
reg->var_off = tnum_or(hi32, tnum_intersect(lo32, range));
}
In the case of the concrete example, this gives us a more conservative unknown
section. Thus, after knowing r1 <= 0x4000000000 and r1 >= 0x2000000000 and
w1 <= 0x400 and w1 >= 0x200:
max: 0b100000000000000000000000000000000000000 / 0x4000000000
var: 0b111111111111111111111111111111111111111 / 0x7fffffffff
min: 0b010000000000000000000000000000000000000 / 0x2000000000
However, above new __reg_bound_offset32() has no effect on refining the
knowledge of the register contents. Meaning, if the bounds in hi32 range
mismatch we'll get the identity function given the range reg spans
[0x0,0xffffffff] and we cast var_off into lo32 only to later on binary
or it again with the hi32.
Likewise, if the bounds in hi32 range match, then we mask both bounds
with 0xffffffff, use the resulting umin/umax for the range to later
intersect the lo32 with it. However, _prior_ called __reg_bound_offset()
did already such intersection on the full reg and we therefore would only
repeat the same operation on the lo32 part twice.
Given this has no effect and the original commit had false assumptions,
this patch reverts the code entirely which is also more straight forward
for stable trees: apparently
581738a681b6 got auto-selected by Sasha's
ML system and misclassified as a fix, so it got sucked into v5.4 where
it should never have landed. A revert is low-risk also from a user PoV
since it requires a recent kernel and llc to opt-into -mcpu=v3 BPF CPU
to generate jmp32 instructions. A proper bounds refinement would need a
significantly more complex approach which is currently being worked, but
no stable material [0]. Hence revert is best option for stable. After the
revert, the original reported program gets rejected as follows:
1: (7f) r0 >>= r0
2: (14) w0 -=
808464432
3: (07) r0 +=
808464432
4: (b7) r1 =
808464432
5: (de) if w1 s<= w0 goto pc+0
R0_w=invP(id=0,umin_value=
808464432,umax_value=
5103431727,var_off=(0x0; 0x1ffffffff)) R1_w=invP808464432 R10=fp0
6: (07) r0 += -
2144337872
7: (14) w0 -= -
1607454672
8: (25) if r0 > 0x30303030 goto pc+0
R0_w=invP(id=0,umax_value=
808464432,var_off=(0x0; 0x3fffffff)) R1_w=invP808464432 R10=fp0
9: (76) if w0 s>= 0x303030 goto pc+2
R0=invP(id=0,umax_value=3158063,var_off=(0x0; 0x3fffff)) R1=invP808464432 R10=fp0
10: (30) r0 = *(u8 *)skb[
808464432]
BPF_LD_[ABS|IND] uses reserved fields
processed 11 insns (limit 1000000) [...]
[0] https://lore.kernel.org/bpf/
158507130343.15666.
8018068546764556975.stgit@john-Precision-5820-Tower/T/
Fixes:
581738a681b6 ("bpf: Provide better register bounds after jmp32 instructions")
Reported-by: Anatoly Trosinenko <anatoly.trosinenko@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200330160324.15259-2-daniel@iogearbox.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Yubo Xie [Fri, 27 Mar 2020 02:11:59 +0000 (19:11 -0700)]
clocksource/drivers/hyper-v: Untangle stimers and timesync from clocksources
[ Upstream commit
0af3e137c144377fbaf5025ba784ff5ba7ad40c9 ]
hyperv_timer.c exports hyperv_cs, which is used by stimers and the
timesync mechanism. However, the clocksource dependency is not
needed: these mechanisms only depend on the partition reference
counter (which can be read via a MSR or via the TSC Reference Page).
Introduce the (function) pointer hv_read_reference_counter, as an
embodiment of the partition reference counter read, and export it
in place of the hyperv_cs pointer. The latter can be removed.
This should clarify that there's no relationship between Hyper-V
stimers & timesync and the Linux clocksource abstractions. No
functional or semantic change.
Suggested-by: Michael Kelley <mikelley@microsoft.com>
Signed-off-by: Andrea Parri <parri.andrea@gmail.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200109160650.16150-2-parri.andrea@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
Heiner Kallweit [Fri, 27 Mar 2020 16:33:32 +0000 (17:33 +0100)]
r8169: fix PHY driver check on platforms w/o module softdeps
commit
2e8c339b4946490a922a21aa8cd869c6cfad2023 upstream.
On Android/x86 the module loading infrastructure can't deal with
softdeps. Therefore the check for presence of the Realtek PHY driver
module fails. mdiobus_register() will try to load the PHY driver
module, therefore move the check to after this call and explicitly
check that a dedicated PHY driver is bound to the PHY device.
Fixes:
f32593773549 ("r8169: check that Realtek PHY driver module is loaded")
Reported-by: Chih-Wei Huang <cwhuang@android-x86.org>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Torsten Hilbrich [Wed, 11 Mar 2020 10:19:06 +0000 (11:19 +0100)]
vti6: Fix memory leak of skb if input policy check fails
commit
2a9de3af21aa8c31cd68b0b39330d69f8c1e59df upstream.
The vti6_rcv function performs some tests on the retrieved tunnel
including checking the IP protocol, the XFRM input policy, the
source and destination address.
In all but one places the skb is released in the error case. When
the input policy check fails the network packet is leaked.
Using the same goto-label discard in this case to fix this problem.
Fixes:
ed1efb2aefbb ("ipv6: Add support for IPsec virtual tunnel interfaces")
Signed-off-by: Torsten Hilbrich <torsten.hilbrich@secunet.com>
Reviewed-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / platform / kernel / linux-rpi.git / log