net: ethernet: ti: am65-cpsw: Enable SGMII mode for J721E

TI's J721E SoC supports SGMII mode with the CPSW9G instance of the CPSW
Ethernet Switch. Thus, enable it by adding SGMII mode to the extra_modes
member of the "j721e_cpswxg_pdata" SoC data.

Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: ethernet: ti: am65-cpsw: Enable SGMII mode for J7200

TI's J7200 SoC supports SGMII mode with the CPSW5G instance of the CPSW
Ethernet Switch. Thus, enable it by adding SGMII mode to the extra_modes
member of the "j7200_cpswxg_pdata" SoC data.

Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: ethernet: ti: am65-cpsw: Add support for SGMII mode

Add support for configuring the CPSW Ethernet Switch in SGMII mode.

Depending on the SoC, allow selecting SGMII mode as a supported interface,
based on the compatible used.

Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: ethernet: ti: am65-cpsw: Simplify setting supported interface

Convert the existing IF/ELSE statement based approach of setting the
supported_interfaces member of struct "phylink_config", to SWITCH
statements. This will help scale to newer PHY-MODES as well as newer
compatibles.

Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

liquidio: remove unused IQ_INSTR_MODE_64B function

clang with W=1 reports
drivers/net/ethernet/cavium/liquidio/request_manager.c:43:19: error:
  unused function 'IQ_INSTR_MODE_64B' [-Werror,-Wunused-function]
static inline int IQ_INSTR_MODE_64B(struct octeon_device *oct, int iq_no)
                  ^
This function and its macro wrapper are not used, so remove them.

Signed-off-by: Tom Rix <trix@redhat.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230321184811.1827306-1-trix@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Merge tag 'ipsec-libreswan-mlx5' of https://git./linux/kernel/git/mellanox/linux

Leon Romanovsky says:

====================
Extend packet offload to fully support libreswan

The following patches are an outcome of Raed's work to add packet
offload support to libreswan [1].

The series includes:
 * Priority support to IPsec policies
 * Statistics per-SA (visible through "ip -s xfrm state ..." command)
 * Support to IKE policy holes
 * Fine tuning to acquire logic.

[1] https://github.com/libreswan/libreswan/pull/986
Link: https://lore.kernel.org/all/cover.1678714336.git.leon@kernel.org
* tag 'ipsec-libreswan-mlx5' of https://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux:
  net/mlx5e: Update IPsec per SA packets/bytes count
  net/mlx5e: Use one rule to count all IPsec Tx offloaded traffic
  net/mlx5e: Support IPsec acquire default SA
  net/mlx5e: Allow policies with reqid 0, to support IKE policy holes
  xfrm: copy_to_user_state fetch offloaded SA packets/bytes statistics
  xfrm: add new device offload acquire flag
  net/mlx5e: Use chains for IPsec policy priority offload
  net/mlx5: fs_core: Allow ignore_flow_level on TX dest
  net/mlx5: fs_chains: Refactor to detach chains from tc usage
====================

Link: https://lore.kernel.org/r/20230320094722.1009304-1-leon@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

dt-bindings: net: Drop unneeded quotes

Cleanup bindings dropping unneeded quotes. Once all these are fixed,
checking for this can be enabled in yamllint.

Acked-by: Marc Kleine-Budde <mkl@pengutronix.de> # for bindings/net/can
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Steen Hegelund <Steen.Hegelund@microchip.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp> # for bindings/net/toshiba,visconti-dwmac.yaml
Reviewed-by: Heiko Stuebner <heiko@sntech.de> #rockchip
Link: https://lore.kernel.org/r/20230320233758.2918972-1-robh@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Merge branch 'net-dsa-b53-configure-6318-and-63268-rgmii-ports'

Álvaro Fernández Rojas says:

====================
net: dsa: b53: configure 6318 and 63268 RGMII ports

BCM6318 and BCM63268 need special configuration for their RGMII ports, so we
need to be able to identify them as a special BCM63xx switch.
In the meantime, let's add some missing BCM63xx SoCs to B53 MMAP device table.

This should be applied after "net: dsa: b53: add support for BCM63xx RGMIIs":
https://patchwork.kernel.org/project/netdevbpf/patch/20230319220805.124024-1-noltari@gmail.com/

Álvaro Fernández Rojas (4):
  dt-bindings: net: dsa: b53: add more 63xx SoCs
  net: dsa: b53: mmap: add more 63xx SoCs
  net: dsa: b53: mmap: allow passing a chip ID
  net: dsa: b53: add BCM63268 RGMII configuration

 .../devicetree/bindings/net/dsa/brcm,b53.yaml |  3 ++
 drivers/net/dsa/b53/b53_common.c              | 19 +++++++++++-
 drivers/net/dsa/b53/b53_mmap.c                | 29 +++++++++++++++----
 drivers/net/dsa/b53/b53_priv.h                |  9 +++++-
 drivers/net/dsa/b53/b53_regs.h                |  1 +
 5 files changed, 53 insertions(+), 8 deletions(-)
====================

Link: https://lore.kernel.org/r/20230321173359.251778-1-noltari@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: dsa: b53: add BCM63268 RGMII configuration

BCM63268 requires special RGMII configuration to work.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: dsa: b53: mmap: allow passing a chip ID

BCM6318 and BCM63268 SoCs require a special handling for their RGMIIs, so we
should be able to identify them as a special BCM63xx switch.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: dsa: b53: mmap: add more 63xx SoCs

BCM6318, BCM6362 and BCM63268 are SoCs with a B53 MMAP switch.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

dt-bindings: net: dsa: b53: add more 63xx SoCs

BCM6318, BCM6362 and BCM63268 are SoCs with a B53 MMAP switch.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

ethernet: remove superfluous clearing of phydev

phy_disconnect() calls phy_detach() which already clears 'phydev' if it
is attached to a struct net_device.

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20230321131745.27688-1-wsa+renesas@sang-engineering.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Merge branch 'bnxt-ptp-optimizations'

Pavan Chebbi says:

====================
bnxt PTP optimizations

Patches to
1. Enforce software based freq adjustments only on shared PHC NIC

2. A prerequisite change to expand capability storage field to
   accommodate more Firmware reported capabilities
====================

Link: https://lore.kernel.org/r/20230321144449.15289-1-pavan.chebbi@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

bnxt: Enforce PTP software freq adjustments only when in non-RTC mode

Currently driver performs software based frequency adjustments
when RTC capability is not discovered or when in shared PHC mode.
But there may be some old firmware versions that still support
hardware freq adjustments without RTC capability being exposed.
In this situation driver will use non-realtime mode even on single
host NICs.

Hence enforce software frequency adjustments only when running in
shared PHC mode. Make suitable changes for cyclecounter for the
same.

Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Acked-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

bnxt: Defer PTP initialization to after querying function caps

Driver uses the flag BNXT_FLAG_MULTI_HOST to determine whether
to use non-realtime mode PHC when running on a multi host NIC.
However when ptp initializes on a NIC with shared PHC, we still
don't have this flag set yet because HWRM_FUNC_QCFG is issued
much later.

Move the ptp initialization code after we have issued func_qcfg.
The next patch will use the BNXT_FLAG_MULTI_HOST flag during PTP
initialization.

Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Acked-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

bnxt: Change fw_cap to u64 to accommodate more capability bits

The current fw_cap field (u32) has run out of bits to save any
new capability.

Change the field to u64.

Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Acked-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

selftests/net: Add SHA256 computation over data sent in tcp_mmap

Add option to compute and send SHA256 over data sent (-i).

This is to ensure the correctness of data received.
Data is randomly populated from /dev/urandom.

Tested:
./tcp_mmap -s -z -i
./tcp_mmap -z -H $ADDR -i
SHA256 is correct

./tcp_mmap -s -i
./tcp_mmap -H $ADDR -i
SHA256 is correct

Signed-off-by: Coco Li <lixiaoyan@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20230321081202.2370275-2-lixiaoyan@google.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

net-zerocopy: Reduce compound page head access

When compound pages are enabled, although the mm layer still
returns an array of page pointers, a subset (or all) of them
may have the same page head since a max 180kb skb can span 2
hugepages if it is on the boundary, be a mix of pages and 1 hugepage,
or fit completely in a hugepage. Instead of referencing page head
on all page pointers, use page length arithmetic to only call page
head when referencing a known different page head to avoid touching
a cold cacheline.

Tested:
See next patch with changes to tcp_mmap

Correntess:
On a pair of separate hosts as send with MSG_ZEROCOPY will
force a copy on tx if using loopback alone, check that the SHA
on the message sent is equivalent to checksum on the message received,
since the current program already checks for the length.

echo 1024 > /sys/kernel/mm/hugepages/hugepages-2048kB/nr_hugepages
./tcp_mmap -s -z
./tcp_mmap -H $DADDR -z

SHA256 is correct
received 2 MB (100 % mmap'ed) in 0.005914 s, 2.83686 Gbit
  cpu usage user:0.001984 sys:0.000963, 1473.5 usec per MB, 10 c-switches

Performance:
Run neper between adjacent hosts with the same config
tcp_stream -Z --skip-rx-copy -6 -T 20 -F 1000 --stime-use-proc --test-length=30

Before patch: stime_end=37.670000
After patch: stime_end=30.310000

Signed-off-by: Coco Li <lixiaoyan@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20230321081202.2370275-1-lixiaoyan@google.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

sh_eth: remove open coded netif_running()

It had a purpose back in the days, but today we have a handy helper.

Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20230321065826.2044-1-wsa+renesas@sang-engineering.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

net: ethernet: ti: am65-cpts: adjust estf following ptp changes

When the CPTS clock is synced/adjusted by running linuxptp (ptp4l/phc2sys),
it will cause the TSN EST schedule to drift away over time. This is because
the schedule is driven by the EstF periodic counter whose pulse length is
defined in ref_clk cycles and it does not automatically sync to CPTS clock.
   _______
 _|
  ^
  expected cycle start time boundary
   _______________
 _|_|___|_|
  ^
  EstF drifted away -> direction

To fix it, the same PPM adjustment has to be applied to EstF as done to the
PHC CPTS clock, in order to correct the TSN EST cycle length and keep them
in sync.

Drifted cycle:
AM65_CPTS_EVT: 7 e1:01770001 e2:000000ff t:1635968230373377017
AM65_CPTS_EVT: 7 e1:01770001 e2:000000ff t:1635968230373877017
AM65_CPTS_EVT: 7 e1:01770001 e2:000000ff t:1635968230374377017
AM65_CPTS_EVT: 7 e1:01770001 e2:000000ff t:1635968230374877017
AM65_CPTS_EVT: 7 e1:01770001 e2:000000ff t:1635968230375377017
AM65_CPTS_EVT: 7 e1:01770001 e2:000000ff t:1635968230375877023
AM65_CPTS_EVT: 7 e1:01770001 e2:000000ff t:1635968230376377018
AM65_CPTS_EVT: 7 e1:01770001 e2:000000ff t:1635968230376877018
AM65_CPTS_EVT: 7 e1:01770001 e2:000000ff t:1635968230377377018

Stable cycle:
AM65_CPTS_EVT: 7 e1:01770001 e2:000000ff t:1635966863193375473
AM65_CPTS_EVT: 7 e1:01770001 e2:000000ff t:1635966863193875473
AM65_CPTS_EVT: 7 e1:01770001 e2:000000ff t:1635966863194375473
AM65_CPTS_EVT: 7 e1:01770001 e2:000000ff t:1635966863194875473
AM65_CPTS_EVT: 7 e1:01770001 e2:000000ff t:1635966863195375473
AM65_CPTS_EVT: 7 e1:01770001 e2:000000ff t:1635966863195875473
AM65_CPTS_EVT: 7 e1:01770001 e2:000000ff t:1635966863196375473

Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Link: https://lore.kernel.org/r/20230321062600.2539544-1-s-vadapalli@ti.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

net-sysfs: display two backlog queue len separately

Sometimes we need to know which one of backlog queue can be exactly
long enough to cause some latency when debugging this part is needed.
Thus, we can then separate the display of both.

Signed-off-by: Jason Xing <kernelxing@tencent.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230321015746.96994-1-kerneljasonxing@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

virtio/vsock: check transport before skb allocation

Pointer to transport could be checked before allocation of skbuff, thus
there is no need to free skbuff when this pointer is NULL.

Signed-off-by: Arseniy Krasnov <AVKrasnov@sberdevices.ru>
Reviewed-by: Bobby Eshleman <bobby.eshleman@bytedance.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Link: https://lore.kernel.org/r/08d61bef-0c11-c7f9-9266-cb2109070314@sberdevices.ru
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

tools: ynl: skip the explicit op array size when not needed

Jiri suggests it reads more naturally to skip the explicit
array size when possible. When we export the symbol we want
to make sure that the size is right but for statics its
not needed.

Link: https://lore.kernel.org/r/20230321044159.1031040-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Merge branch 'net-remove-some-rcu_bh-cruft'

Eric Dumazet says:

====================
net: remove some rcu_bh cruft

There is no point using rcu_bh variant hoping to free objects faster,
especially hen using call_rcu() or kfree_rcu().

Disabling/enabling BH has a non-zero cost, and adds distracting
hot spots in kernel profiles eg. in ip6_xmit().
====================

Link: https://lore.kernel.org/r/20230321040115.787497-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: remove rcu_dereference_bh_rtnl()

This helper is no longer used in the tree.

Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

neighbour: switch to standard rcu, instead of rcu_bh

rcu_bh is no longer a win, especially for objects freed
with standard call_rcu().

Switch neighbour code to no longer disable BH when not necessary.

Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

ipv6: flowlabel: do not disable BH where not needed

struct ip6_flowlabel are rcu managed, and call_rcu() is used
to delay fl_free_rcu() after RCU grace period.

There is no point disabling BH for pure RCU lookups.

Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: atheros: atl1c: remove unused atl1c_irq_reset function

clang with W=1 reports
drivers/net/ethernet/atheros/atl1c/atl1c_main.c:214:20: error:
  unused function 'atl1c_irq_reset' [-Werror,-Wunused-function]
static inline void atl1c_irq_reset(struct atl1c_adapter *adapter)
                   ^
This function is not used, so remove it.

Signed-off-by: Tom Rix <trix@redhat.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Link: https://lore.kernel.org/r/20230320232317.1729464-1-trix@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: pasemi: Fix return type of pasemi_mac_start_tx()

With clang's kernel control flow integrity (kCFI, CONFIG_CFI_CLANG),
indirect call targets are validated against the expected function
pointer prototype to make sure the call target is valid to help mitigate
ROP attacks. If they are not identical, there is a failure at run time,
which manifests as either a kernel panic or thread getting killed. A
warning in clang aims to catch these at compile time, which reveals:

  drivers/net/ethernet/pasemi/pasemi_mac.c:1665:21: error: incompatible function pointer types initializing 'netdev_tx_t (*)(struct sk_buff *, struct net_device *)' (aka 'enum netdev_tx (*)(struct sk_buff *, struct net_device *)') with an expression of type 'int (struct sk_buff *, struct net_device *)' [-Werror,-Wincompatible-function-pointer-types-strict]
          .ndo_start_xmit         = pasemi_mac_start_tx,
                                    ^~~~~~~~~~~~~~~~~~~
  1 error generated.

->ndo_start_xmit() in 'struct net_device_ops' expects a return type of
'netdev_tx_t', not 'int'. Adjust the return type of
pasemi_mac_start_tx() to match the prototype's to resolve the warning.
While PowerPC does not currently implement support for kCFI, it could in
the future, which means this warning becomes a fatal CFI failure at run
time.

Link: https://github.com/ClangBuiltLinux/linux/issues/1750
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Link: https://lore.kernel.org/r/20230319-pasemi-incompatible-pointer-types-strict-v1-1-1b9459d8aef0@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

net: geneve: accept every ethertype

The Geneve encapsulation, as defined in RFC 8926, has a Protocol Type
field, which states the Ethertype of the payload appearing after the
Geneve header.

Commit 435fe1c0c1f7 ("net: geneve: support IPv4/IPv6 as inner protocol")
introduced a new IFLA_GENEVE_INNER_PROTO_INHERIT flag that allowed the
use of other Ethertypes than Ethernet. However, it did not get rid of a
restriction that prohibits receiving payloads other than Ethernet,
instead the commit white-listed additional Ethertypes, IPv4 and IPv6.

This patch removes this restriction, making it possible to receive any
Ethertype as a payload, if the IFLA_GENEVE_INNER_PROTO_INHERIT flag is
set.

The restriction was set in place back in commit 0b5e8b8eeae4
("net: Add Geneve tunneling protocol driver"), which implemented a
protocol layer driver for Geneve to be used with Open vSwitch. The
relevant discussion about introducing the Ethertype white-list can be
found here:
https://lore.kernel.org/netdev/CAEP_g=_1q3ACX5NTHxLDnysL+dTMUVzdLpgw1apLKEdDSWPztw@mail.gmail.com/

<quote>
>> +       if (unlikely(geneveh->proto_type != htons(ETH_P_TEB)))
>
> Why? I thought the point of geneve carrying protocol field was to
> allow protocols other than Ethernet... is this temporary maybe?

Yes, it is temporary. Currently OVS only handles Ethernet packets but
this restriction can be lifted once we have a consumer that is capable
of handling other protocols.
</quote>

This white-list was then ported to a generic Geneve netdevice in commit
371bd1061d29 ("geneve: Consolidate Geneve functionality in single
module."). Preserving the Ethertype white-list at this point made sense,
as the Geneve device could send out only Ethernet payloads anyways.

However, now that the Geneve netdevice supports encapsulating other
payloads with IFLA_GENEVE_INNER_PROTO_INHERIT and we have a consumer
capable of other protocols, it seems appropriate to lift the restriction
and allow any Geneve payload to be received.

Signed-off-by: Josef Miegl <josef@miegl.cz>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Eyal Birger <eyal.birger@gmail.com>
Link: https://lore.kernel.org/r/20230319220954.21834-1-josef@miegl.cz
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

net: dsa: b53: add support for BCM63xx RGMIIs

BCM63xx RGMII ports require additional configuration in order to work.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230319220805.124024-1-noltari@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

net: dsa: qca8k: remove assignment of an_enabled in pcs_get_state()

pcs_get_state() implementations are not supposed to alter an_enabled.
Remove this assignment.

Fixes: b3591c2a3661 ("net: dsa: qca8k: Switch to PHYLINK instead of PHYLIB")
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1pdsE5-00Dl2l-8F@rmk-PC.armlinux.org.uk
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

net: dsa: mv88e6xxx: fix mdio bus' phy_mask member

Commit 2c7e46edbd03 ("net: dsa: mv88e6xxx: mask apparently non-existing
phys during probing") added non-trivial bus->phy_mask in
mv88e6xxx_mdio_register() in order to avoid excessive mdio bus
transactions during probing.

But the mask is incorrect for switches with non-zero phy_base_addr (such
as 88E6341).

Fix this.

Fixes: 2c7e46edbd03 ("net: dsa: mv88e6xxx: mask apparently non-existing phys during probing")
Signed-off-by: Marek Behún <kabel@kernel.org>
Tested-by: Klaus Kudielka <klaus.kudielka@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20230319140238.9470-1-kabel@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

net: cxgb3: remove unused fl_to_qset function

clang with W=1 reports
drivers/net/ethernet/chelsio/cxgb3/sge.c:169:32: error: unused function
  'fl_to_qset' [-Werror,-Wunused-function]
static inline struct sge_qset *fl_to_qset(const struct sge_fl *q, int qidx)
                               ^
This function is not used, so remove it.

Signed-off-by: Tom Rix <trix@redhat.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Link: https://lore.kernel.org/r/20230319172433.1708161-1-trix@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Merge branch 'net-ethernet-mtk_eth_soc-various-enhancements'

Daniel Golle says:

====================
net: ethernet: mtk_eth_soc: various enhancements

This series brings a variety of fixes and enhancements for mtk_eth_soc,
adds support for the MT7981 SoC and facilitates sharing the SGMII PCS
code between mtk_eth_soc and mt7530.

The whole series has been tested on MT7622+MT7531 (BPi-R64),
MT7623+MT7530 (BPi-R2), MT7981+GPY211 (GL.iNet GL-MT3000) and
MT7986+MT7531 (BPi-R3). On the BananaPi R3 a variete of SFP modules
have been tested, all of them (some SGMII with PHY, others 2500Base-X
or 1000Base-X without PHY) are working well now, however, some of them
need manually disabling of autonegotiation for the link to come up.
====================

Link: https://lore.kernel.org/r/cover.1679230025.git.daniel@makrotopia.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: dsa: mt7530: use external PCS driver

Implement regmap access wrappers, for now only to be used by the
pcs-mtk-lynxi driver.
Make use of this external PCS driver and drop the now reduntant
implementation in mt7530.c.
As a nice side effect the SGMII registers can now also more easily be
inspected for debugging via /sys/kernel/debug/regmap.

Tested-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Tested-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: ethernet: mtk_eth_soc: switch to external PCS driver

Now that we got a PCS driver, use it and remove the now redundant
PCS code and it's header macros from the Ethernet driver.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Tested-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: pcs: add driver for MediaTek SGMII PCS

The SGMII core found in several MediaTek SoCs is identical to what can
also be found in MediaTek's MT7531 Ethernet switch IC.
As this has not always been clear, both drivers developed different
implementations to deal with the PCS.
Recently Alexander Couzens pointed out this fact which lead to the
development of this shared driver.

Add a dedicated driver, mostly by copying the code now found in the
Ethernet driver. The now redundant code will be removed by a follow-up
commit.

Suggested-by: Alexander Couzens <lynxis@fe80.eu>
Suggested-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Tested-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: ethernet: mtk_eth_soc: ppe: add support for flow accounting

The PPE units found in MT7622 and newer support packet and byte
accounting of hw-offloaded flows. Add support for reading those counters
as found in MediaTek's SDK[1].

[1]: https://git01.mediatek.com/plugins/gitiles/openwrt/feeds/mtk-openwrt-feeds/+/bc6a6a375c800dc2b80e1a325a2c732d1737df92
Tested-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: ethernet: mtk_eth_soc: set MDIO bus clock frequency

Set MDIO bus clock frequency and allow setting a custom maximum
frequency from device tree.

Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

dt-bindings: net: pcs: mediatek,sgmiisys: add MT7981 SoC

Add mediatek,pnswap boolean property needed on many boards using the
MediaTek MT7981 SoC.

Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

dt-bindings: arm: mediatek: sgmiisys: Convert to DT schema

Convert mediatek,sgmiiisys bindings to DT schema format.
Add maintainer Matthias Brugger, no maintainers were listed in the
original documentation.
As this node is also referenced by the Ethernet controller and used
as SGMII PCS add this fact to the description.
Move the file to Documentation/devicetree/bindings/net/pcs/ which seems
more appropriate given that the great majority of registers are related
to SGMII PCS functionality and only one register represents clock bits.

Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

dt-bindings: net: mediatek,net: add mt7981-eth binding

Introduce DT bindings for the MT7981 SoC to mediatek,net.yaml.

Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: ethernet: mtk_eth_soc: add support for MT7981 SoC

The MediaTek MT7981 SoC comes with two 1G/2.5G SGMII ports, just like
MT7986.

In addition MT7981 is equipped with a built-in 1000Base-T PHY which can
be used with GMAC1.

As many MT7981 boards make use of inverting SGMII signal polarity, add
new device-tree attribute 'mediatek,pn_swap' to support them.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

MAINTAINERS: remove file entry in NFC SUBSYSTEM after platform_data movement

Commit 053fdaa841bd ("nfc: mrvl: Move platform_data struct into driver")
moves the nfcmrvl.h header file from include/linux/platform_data to the
driver's directory, but misses to adjust MAINTAINERS.

Hence, ./scripts/get_maintainer.pl --self-test=patterns complains about a
broken reference.

Just remove the file entry in NFC SUBSYSTEM, as the new location of the
code is already covered by another pattern in that section.

Fixes: 053fdaa841bd ("nfc: mrvl: Move platform_data struct into driver")
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

r8169: consolidate disabling ASPM before EPHY access

Now that rtl_hw_aspm_clkreq_enable() is a no-op for chip versions < 32,
we can consolidate disabling ASPM before EPHY access in rtl_hw_start().

Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'reuse-smsc-phy-functionality'

Heiner Kallweit says:

====================
net: phy: reuse SMSC PHY driver functionality in the meson-gxl PHY driver

The Amlogic Meson internal PHY's have the same register layout as
certain SMSC PHY's (also for non-c22-standard registers). This seems
to be more than just coincidence. Apparently they also need the same
workaround for EDPD mode (energy detect power down). Therefore let's
reuse SMSC PHY driver functionality in the meson-gxl PHY driver.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

net: phy: meson-gxl: reuse functionality of the SMSC PHY driver

The Amlogic Meson internal PHY's have the same register layout as
certain SMSC PHY's (also for non-c22-standard registers). This seems
to be more than just coincidence. Apparently they also need the same
workaround for EDPD mode (energy detect power down). Therefore let's
reuse SMSC PHY driver functionality in the meson-gxl PHY driver.

Tested with a G12A internal PHY. I don't have GXL test hw,
therefore I replace only the callbacks that are identical in
the SMSC PHY driver.

Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: phy: smsc: export functions for use by meson-gxl PHY driver

The Amlogic Meson internal PHY's have the same register layout as
certain SMSC PHY's (also for non-c22-standard registers). This seems
to be more than just coincidence. Apparently they also need the same
workaround for EDPD mode (energy detect power down). Therefore let's
export SMSC PHY driver functionality for use by the meson-gxl PHY
driver.

Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Chris Healy <healych@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net/mlx5e: Update IPsec per SA packets/bytes count

Providing per SA packets/bytes statistics mandates creating unique
counter per SA flow for Rx/Tx, whenever offloaded SA statistics is
desired query the specific SA counter to provide the stack with the
needed data.

Signed-off-by: Raed Salem <raeds@nvidia.com>
Link: https://lore.kernel.org/r/7d5ce20ac495f3054afb633128700e7b7eeeb3cd.1678714336.git.leon@kernel.org
Signed-off-by: Leon Romanovsky <leon@kernel.org>

net/mlx5e: Use one rule to count all IPsec Tx offloaded traffic

Currently one counter is shared between all IPsec Tx offloaded
rules to count the total amount of packets/bytes that was IPsec
Tx offloaded, replace this scheme by adding a new flow table (ft)
with one rule that counts all flows that passes through this
table (like Rx status ft), this ft is pointed by all IPsec Tx
offloaded rules. The above allows to have a counter per tx flow
rule in while keeping a separate global counter that store the
aggregation outcome of all these per flow counters.

Signed-off-by: Raed Salem <raeds@nvidia.com>
Link: https://lore.kernel.org/r/09b9119d1deb6e482fd2d17e1f5760d7c5be1e48.1678714336.git.leon@kernel.org
Signed-off-by: Leon Romanovsky <leon@kernel.org>

net/mlx5e: Support IPsec acquire default SA

During XFRM stack acquire flow, a default SA is created to be updated
later, once acquire netlink message is handled in user space.

This SA is also passed to IPsec offload supporting driver, however this
SA acts only as placeholder and does not have context suitable for
offloading in HW yet. Identify this kind of SA by special offload flag
(XFRM_DEV_OFFLOAD_FLAG_ACQ), and create a SW only context.

In such cases with special mark so it won't be installed in HW in addition
flow and on remove/delete free this SW only context.

Signed-off-by: Raed Salem <raeds@nvidia.com>
Link: https://lore.kernel.org/r/8f36d6b61631dcd73fef0a0ac623456030bc9db0.1678714336.git.leon@kernel.org
Signed-off-by: Leon Romanovsky <leon@kernel.org>

net/mlx5e: Allow policies with reqid 0, to support IKE policy holes

IKE policies hole, is special policy that exists to allow for IKE
traffic to bypass IPsec encryption even though there is already a
policies and SA(s) configured on same endpoints, these policies
does not nessecarly have the reqid configured, so need to add
an exception for such policies. These kind of policies are allowed
under the condition that at least upper protocol and/or ips
are not 0.

Signed-off-by: Raed Salem <raeds@nvidia.com>
Link: https://lore.kernel.org/r/cbcadde312c24de74c47d9b0616f86a5818cc9bf.1678714336.git.leon@kernel.org
Signed-off-by: Leon Romanovsky <leon@kernel.org>

xfrm: copy_to_user_state fetch offloaded SA packets/bytes statistics

Both in RX and TX, the traffic that performs IPsec packet offload
transformation is accounted by HW only. Consequently, the HW should
be queried for packets/bytes statistics when user asks for such
transformation data.

Signed-off-by: Raed Salem <raeds@nvidia.com>
Link: https://lore.kernel.org/r/d90ec74186452b1509ee94875d942cb777b7181e.1678714336.git.leon@kernel.org
Acked-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>

xfrm: add new device offload acquire flag

During XFRM acquire flow, a default SA is created to be updated later,
once acquire netlink message is handled in user space. When the relevant
policy is offloaded this default SA is also offloaded to IPsec offload
supporting driver, however this SA does not have context suitable for
offloading in HW, nor is interesting to offload to HW, consequently needs
a special driver handling apart from other offloaded SA(s).
Add a special flag that marks such SA so driver can handle it correctly.

Signed-off-by: Raed Salem <raeds@nvidia.com>
Link: https://lore.kernel.org/r/f5da0834d8c6b82ab9ba38bd4a0c55e71f0e3dab.1678714336.git.leon@kernel.org
Acked-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>

net/mlx5e: Use chains for IPsec policy priority offload

Currently, policy priority field is ignored and so order
of matching is unpredictable.

Use chains for RX/TX policy offload to support the
priority field.

Signed-off-by: Paul Blakey <paulb@nvidia.com>
Reviewed-by: Raed Salem <raeds@nvidia.com>
Link: https://lore.kernel.org/r/9ef3ef88858217932696ad413b1b147b799a11be.1678714336.git.leon@kernel.org
Signed-off-by: Leon Romanovsky <leon@kernel.org>

net/mlx5: fs_core: Allow ignore_flow_level on TX dest

ignore_flow_level is also supported by firmware on TX,
remove this limitation.

Signed-off-by: Paul Blakey <paulb@nvidia.com>
Reviewed-by: Raed Salem <raeds@nvidia.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Link: https://lore.kernel.org/r/d0025722bfac0a82da758eb540fbf1ff3cacdf74.1678714336.git.leon@kernel.org
Signed-off-by: Leon Romanovsky <leon@kernel.org>

net/mlx5: fs_chains: Refactor to detach chains from tc usage

To support more generic chains that will be used on other
namespaces and without tc, refactor to remove the dependency
on tc terms.

Signed-off-by: Paul Blakey <paulb@nvidia.com>
Reviewed-by: Raed Salem <raeds@nvidia.com>
Link: https://lore.kernel.org/r/bb8570d532d569285b5bff981578507bd15350cb.1678714336.git.leon@kernel.org
Signed-off-by: Leon Romanovsky <leon@kernel.org>

Merge branch 'ocelot-external-ports'

Colin Foster says:

====================
add support for ocelot external ports

This is the start of part 3 of what is hopefully a 3-part series to add
Ethernet switching support to Ocelot chips.

Part 1 of the series (A New Chip) added general support for Ocelot chips
that were controlled externally via SPI.
https://lore.kernel.org/all/20220815005553.1450359-1-colin.foster@in-advantage.com/

Part 2 of the series (The Ethernet Strikes Back) added DSA Ethernet
support for ports 0-3, which are the four copper ports that are internal
to the chip.
https://lore.kernel.org/all/20230127193559.1001051-1-colin.foster@in-advantage.com/

Part 3 will, at a minimum, add support for ports 4-7, which are
configured to use QSGMII to an external phy (Return Of The QSGMII). With
any luck, and some guidance, support for SGMII, SFPs, etc. will also be
part of this series.

V1 was submitted as an RFC - and that was rightly so. I suspected I
wasn't doing something right, and that was certainly the case. V2 is
much cleaner, so hopefully upgrading it to PATCH status is welcomed.

Thanks to Russell and Vladimir for correcting my course from V1.

In V1 I included a device tree snippet. I won't repeat that here, but
I will include a boot log snippet, in case it is of use:
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: ocelot: add support for external phys

The VSC7512 has four ports with internal phys that are already supported.
There are additional ports that can be configured to work with external
phys.

Add support for these additional ethernet ports.

Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: felix: allow serdes configuration for dsa ports

Ports for Ocelot devices (VSC7511, VSC7512, VSC7513 and VSC7514) support
external phys. When external phys are used, additional configuration on
each port is required to enable QSGMII mode and set external phy modes.

Add a configurable hook into these routines, so the external ports can be
used.

Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: felix: allow configurable phylink_mac_config

If a user of the Felix driver has a port running in SGMII / QSGMII mode, it
will need to utilize phylink_mac_config(). Add this configurability.

Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: felix: attempt to initialize internal hsio plls

The VSC7512 and VSC7514 have internal PLLs that can be used to control
different peripherals. Initialize these high speed I/O (HSIO) PLLs when
they exist, so that dependent peripherals like QSGMII can function.

Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: mscc: ocelot: expose serdes configuration function

During chip initialization, ports that use SGMII / QSGMII to interface to
external phys need to be configured on the VSC7513 and VSC7514. Expose this
configuration routine, so it can be used by DSA drivers.

Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: mscc: ocelot: expose generic phylink_mac_config routine

The ocelot-switch driver can utilize the phylink_mac_config routine. Move
this to the ocelot library location and export the symbol to make this
possible.

Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: mscc: ocelot: expose ocelot_pll5_init routine

Ocelot chips have an internal PLL that must be used when communicating
through external phys. Expose the init routine, so it can be used by other
drivers.

Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

mfd: ocelot: add ocelot-serdes capability

Add support for the Ocelot SERDES module to support functionality of all
non-internal phy ports.

Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

phy: phy-ocelot-serdes: add ability to be used in a non-syscon configuration

The phy-ocelot-serdes module has exclusively been used in a syscon setup,
from an internal CPU. The addition of external control of ocelot switches
via an existing MFD implementation means that syscon is no longer the only
interface that phy-ocelot-serdes will see.

In the MFD configuration, an IORESOURCE_REG resource will exist for the
device. Utilize this resource to be able to function in both syscon and
non-syscon configurations.

Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'lan966x-tx-rx-improve'

Horatiu Vultur says:

====================
net: lan966x: Improve TX/RX of frames from/to CPU

The first patch of this series improves the RX side. As it seems to be
an expensive operation to read the RX timestamp for every frame, then
read it only if it is required. This will give an improvement of ~70mbit
on the RX side.
The second patch stops using the packing library. This improves mostly
the TX side as this library is used to set diffent bits in the IFH. If
this library is replaced with a more simple/shorter implementation,
this gives an improvement of more than 100mbit on TX side.
All the measurements were done using iperf3.

v1->v2:
- update lan966x_ifh_set to set the bytes and not each bit individually
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

net: lan966x: Stop using packing library

When a frame is injected from CPU, it is required to create an IFH(Inter
frame header) which sits in front of the frame that is transmitted.
This IFH, contains different fields like destination port, to bypass the
analyzer, priotity, etc. Lan966x it is using packing library to set and
get the fields of this IFH. But this seems to be an expensive
operations.
If this is changed with a simpler implementation, the RX will be
improved with ~5Mbit while on the TX is a much bigger improvement as it
is required to set more fields. Below are the numbers for TX.

Before:
[  5]   0.00-10.02  sec   439 MBytes   367 Mbits/sec    0 sender

After:
[  5]   0.00-10.00  sec   578 MBytes   485 Mbits/sec    0 sender

Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: lan966x: Don't read RX timestamp if not needed

Whenever a frame was received to the CPU, the HW is timestamping the
frame. In the IFH(Inter Frame Header) it is found the nanosecond part
of the timestamps the SW is required to read from HW the second part.
But reading the second part it seems to be a expensive operations, so
so change this such to read the second part only when rx filter is
enabled.
Doing this change gives the RX a performance boost of ~70mbit.

before:
[  5]   0.00-10.01  sec   546 MBytes   457 Mbits/sec    0 sender

now:
[  5]   0.00-10.01  sec   652 MBytes   530 Mbits/sec    0 sender

Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net/packet: remove po->xmit

Use PACKET_SOCK_QDISC_BYPASS atomic bit instead of a pointer.

This removes one indirect call in fast path,
and READ_ONCE()/WRITE_ONCE() annotations as well.

Signed-off-by: Eric Dumazet <edumazet@google.com>
Suggested-by: Willem de Bruijn <willemb@google.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: macb: Reset TX when TX halt times out

Reset TX when halt times out i.e. disable TX, clean up TX BDs,
interrupts (already done) and enable TX.
This addresses the issue observed when iperf is run at 10Mps Half
duplex where, after multiple collisions and retries, TX halts.

Signed-off-by: Harini Katakam <harini.katakam@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ixgb: Remove ixgb driver

There are likely no users of this driver as the hardware has been
discontinued since 2010. Remove the driver and all references to it
in documentation.

Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: phy: at803x: Replace of_gpio.h with what indeed is used

of_gpio.h in this driver is solely used as a proxy to other headers.
This is incorrect usage of the of_gpio.h. Replace it .h with what
indeed is used in the code.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: smc91x: Replace of_gpio.h with what indeed is used

of_gpio.h in this driver is solely used as a proxy to other headers.
This is incorrect usage of the of_gpio.h. Replace it .h with what
indeed is used in the code.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: macb: Set MDIO clock divisor for pclk higher than 160MHz

Currently macb sets clock divisor for pclk up to 160 MHz.
Function gem_mdc_clk_div was updated to enable divisor
for higher values of pclk.

Signed-off-by: Bartosz Wawrzyniak <bwawrzyn@cisco.com>
Reviewed-by: Michal Kubiak <michal.kubiak@intel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'net-better-const'

Eric Dumazet says:

====================
net: better const qualifier awareness

This is a follow-up of d27d367d3b78 ("inet: better const qualifier awareness")

Adopting container_of_const() to perform (struct sock *)->(protocol sock *)
operation is allowing us to propagate const qualifier and thus detect
misuses at compile time.

Most conversions are trivial, because most protocols did not adopt yet
const sk pointers where it could make sense.

Only mptcp and tcp patches (end of this series) are requiring small
adjustments.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

tcp: preserve const qualifier in tcp_sk()

We can change tcp_sk() to propagate its argument const qualifier,
thanks to container_of_const().

We have two places where a const sock pointer has to be upgraded
to a write one. We have been using const qualifier for lockless
listeners to clearly identify points where writes could happen.

Add tcp_sk_rw() helper to better document these.

tcp_inbound_md5_hash(), __tcp_grow_window(), tcp_reset_check()
and tcp_rack_reo_wnd() get an additional const qualififer
for their @tp local variables.

smc_check_reset_syn_req() also needs a similar change.

Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

mptcp: preserve const qualifier in mptcp_sk()

We can change mptcp_sk() to propagate its argument const qualifier,
thanks to container_of_const().

We need to change few things to avoid build errors:

mptcp_set_datafin_timeout() and mptcp_rtx_head() have to accept
non-const sk pointers.

@msk local variable in mptcp_pending_tail() must be const.

Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Matthieu Baerts <matthieu.baerts@tessares.net>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

x25: preserve const qualifier in [a]x25_sk()

We can change [a]x25_sk() to propagate their argument const qualifier,
thanks to container_of_const().

Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

smc: preserve const qualifier in smc_sk()

We can change smc_sk() to propagate its argument const qualifier,
thanks to container_of_const().

Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Karsten Graul <kgraul@linux.ibm.com>
Cc: Wenjia Zhang <wenjia@linux.ibm.com>
Cc: Jan Karcher <jaka@linux.ibm.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Wenjia Zhang <wenjia@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

af_unix: preserve const qualifier in unix_sk()

We can change unix_sk() to propagate its argument const qualifier,
thanks to container_of_const().

We need to change dump_common_audit_data() 'struct unix_sock *u'
local var to get a const attribute.

Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

dccp: preserve const qualifier in dccp_sk()

We can change dccp_sk() to propagate its argument const qualifier,
thanks to container_of_const().

Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ipv6: raw: preserve const qualifier in raw6_sk()

We can change raw6_sk() to propagate its argument const qualifier,
thanks to container_of_const().

Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

raw: preserve const qualifier in raw_sk()

We can change raw_sk() to propagate const qualifier of its argument,
thanks to container_of_const()

Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

af_packet: preserve const qualifier in pkt_sk()

We can change pkt_sk() to propagate const qualifier of its argument,
thanks to container_of_const()

This should avoid some potential errors caused by accidental
(const -> not_const) promotion.

Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

udp: preserve const qualifier in udp_sk()

We can change udp_sk() to propagate const qualifier of its argument,
thanks to container_of_const()

This should avoid some potential errors caused by accidental
(const -> not_const) promotion.

Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'net-mlx5e-add-gbp-vxlan-hw-offload-support'

Gavin Li says:

====================
net/mlx5e: Add GBP VxLAN HW offload support

Patch-1: Remove unused argument from functions.
Patch-2: Expose helper function vxlan_build_gbp_hdr.
Patch-3: Add helper function for encap_info_equal for tunnels with options.
Patch-4: Preserving the const-ness of the pointer in ip_tunnel_info_opts.
Patch-5: Add HW offloading support for TC flows with VxLAN GBP encap/decap
        in mlx ethernet driver.
====================

Link: https://lore.kernel.org/r/20230316070758.83512-1-gavinl@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net/mlx5e: TC, Add support for VxLAN GBP encap/decap flows offload

Add HW offloading support for TC flows with VxLAN GBP encap/decap.

Example of encap rule:
tc filter add dev eth0 protocol ip ingress flower \
    action tunnel_key set id 42 vxlan_opts 512 \
    action mirred egress redirect dev vxlan1

Example of decap rule:
tc filter add dev vxlan1 protocol ip ingress flower \
    enc_key_id 42 enc_dst_port 4789 vxlan_opts 1024 \
    action tunnel_key unset action mirred egress redirect dev eth0

Signed-off-by: Gavin Li <gavinl@nvidia.com>
Reviewed-by: Gavi Teitz <gavi@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Maor Dickman <maord@nvidia.com>
Acked-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

ip_tunnel: Preserve pointer const in ip_tunnel_info_opts

Change ip_tunnel_info_opts( ) from static function to macro to cast return
value and preserve the const-ness of the pointer.

Signed-off-by: Gavin Li <gavinl@nvidia.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net/mlx5e: Add helper for encap_info_equal for tunnels with options

For tunnels with options, eg, geneve and vxlan with gbp, they share the
same way to compare the headers and options. Extract the code as a common
function for them.

Signed-off-by: Gavin Li <gavinl@nvidia.com>
Reviewed-by: Gavi Teitz <gavi@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Maor Dickman <maord@nvidia.com>
Acked-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

vxlan: Expose helper vxlan_build_gbp_hdr

The function vxlan_build_gbp_hdr will be used by other modules to build
gbp option in vxlan header according to gbp flags.

Signed-off-by: Gavin Li <gavinl@nvidia.com>
Reviewed-by: Gavi Teitz <gavi@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Maor Dickman <maord@nvidia.com>
Acked-by: Saeed Mahameed <saeedm@nvidia.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

vxlan: Remove unused argument from vxlan_build_gbp_hdr( ) and vxlan_build_gpe_hdr( )

Remove unused argument (i.e. u32 vxflags) in vxlan_build_gbp_hdr( ) and
vxlan_build_gpe_hdr( ) function arguments.

Signed-off-by: Gavin Li <gavinl@nvidia.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

wwan: core: Support slicing in port TX flow of WWAN subsystem

wwan_port_fops_write inputs the SKB parameter to the TX callback of
the WWAN device driver. However, the WWAN device (e.g., t7xx) may
have an MTU less than the size of SKB, causing the TX buffer to be
sliced and copied once more in the WWAN device driver.

This patch implements the slicing in the WWAN subsystem and gives
the WWAN devices driver the option to slice(by frag_len) or not. By
doing so, the additional memory copy is reduced.

Meanwhile, this patch gives WWAN devices driver the option to reserve
headroom in fragments for the device-specific metadata.

Signed-off-by: haozhe chang <haozhe.chang@mediatek.com>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Link: https://lore.kernel.org/r/20230316095826.181904-1-haozhe.chang@mediatek.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: macb: Increase halt timeout to accommodate 10Mbps link

Increase halt timeout to accommodate for 16K SRAM at 10Mbps rounded.

Signed-off-by: Harini Katakam <harini.katakam@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20230316083050.2108-1-harini.katakam@amd.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

dt-bindings: net: qcom,ipa: add SDX65 compatible

Add support for SDX65, which uses IPA v5.0.

Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Alex Elder <elder@linaro.org>
Link: https://lore.kernel.org/r/20230315194305.1647311-1-elder@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Merge branch 'net-dsa-mv88e6xxx-accelerate-c45-scan'

Klaus Kudielka says:

====================
net: dsa: mv88e6xxx: accelerate C45 scan

Starting with commit 1a136ca2e089 ("net: mdio: scan bus based on bus
capabilities for C22 and C45"), mdiobus_scan_bus_c45() is being called on
buses with MDIOBUS_NO_CAP. On a Turris Omnia (Armada 385, 88E6176 switch),
this causes a significant increase of boot time, from 1.6 seconds, to 6.3
seconds. The boot time stated here is until start of /init.

Further testing revealed that the C45 scan is indeed expensive (around
2.7 seconds, due to a huge number of bus transactions), and called twice.

Two things were suggested:
(1) to move the expensive call of mv88e6xxx_mdios_register() from
    mv88e6xxx_probe() to mv88e6xxx_setup().
(2) to mask apparently non-existing phys during probing.

Before that:
Patch #1 prepares the driver to handle the movement of
mv88e6xxx_mdios_register() to mv88e6xxx_setup() for cross-chip DSA trees.
Patch #2 is preparatory code movement, without functional change.

With those changes, boot time on the Turris Omnia is back to normal.

Link: https://lore.kernel.org/lkml/449bde236c08d5ab5e54abd73b645d8b29955894.camel@gmail.com/
====================

Link: https://lore.kernel.org/r/20230315163846.3114-1-klaus.kudielka@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: dsa: mv88e6xxx: mask apparently non-existing phys during probing

To avoid excessive mdio bus transactions during probing, mask all phy
addresses that do not exist (there is a 1:1 mapping between switch port
number and phy address).

Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Klaus Kudielka <klaus.kudielka@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>