Simon Glass [Sat, 24 Aug 2019 13:22:52 +0000 (07:22 -0600)]
binman: Use tools.Run() to run objdump
At present this command silently fails if something goes wrong. Use the
tools.Run() function instead, since it reports errors.
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Sat, 24 Aug 2019 13:22:51 +0000 (07:22 -0600)]
binman: Fix IFWI output when using an Intel FIT image
At present this entry does not work correctly when a FIT image is used as
the input. It updates the FIT instead of the output image. The test passed
because the FIT image happened to have the right data already.
Fix it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Sat, 24 Aug 2019 13:22:50 +0000 (07:22 -0600)]
binman: Add support for Intel FIT
A Firmware Image Table (FIT) is a data structure defined by Intel which
contains information about various things needed by the SoC, such as
microcode.
Add support for this entry as well as the pointer to it. The contents of
FIT are fixed at present. Future work is needed to support adding
microcode, etc.
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Sat, 24 Aug 2019 13:22:49 +0000 (07:22 -0600)]
binman: x86: Separate out 16-bit reset and init code
At present these two sections of code are linked together into a single
2KB chunk in a single file. Some Intel SoCs like to have a FIT (Firmware
Interface Table) in the ROM and the pointer for this needs to go at
0xffffffc0 which is in the middle of these two sections.
Make use of the new 'reset' entry and change the existing 16-bit entry to
include just the 16-bit data.
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Sat, 24 Aug 2019 13:22:48 +0000 (07:22 -0600)]
binman: Add support for an x86 'reset' section
At present binman has a single entry type for the 16-bit code code needed
to start up an x86 processor. This entry is intended to include both the
reset vector itself as well as the code to move to 32-bit mode.
However this is not very flexible since in some cases other data needs to
be included at the top of the SPI flash, in between these two pieces. For
example Intel requires that a FIT (Firmware Image Table) pointer be placed
0x40 bytes before the end of the ROM.
To deal with this, add a new reset entry for just the reset vector. A
subsequent change will adjust the existing 'start16' entry.
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Sat, 24 Aug 2019 13:22:47 +0000 (07:22 -0600)]
binman: Correct use of 'replace' in IFWI tests
At present the Intel IFWI entry uses 'replace' without the 'ifwi-' prefix.
This is a fairly generic name which might conflict with the main Entry
base class at some point, if more features are added. Add a prefix.
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Sat, 24 Aug 2019 13:22:46 +0000 (07:22 -0600)]
binman: Handle hidden symbols in ELF files
Some versions of binutils generate hidden symbols which are currently not
parsed by binman. Correct this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Sat, 24 Aug 2019 13:22:45 +0000 (07:22 -0600)]
binman: Drop .note section from ELF
Recent versions of binutils add a '.note.gnu.property' into the ELF file.
This is not required and interferes with the expected output. Drop it.
Also fix testMakeElf() to use a different file for input and output.
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Sat, 24 Aug 2019 13:22:44 +0000 (07:22 -0600)]
binman: Allow use of help and entry-docs without libfdt
At present if libfdt is not available binman can't do anything much.
Improve the situation a little.
Ideally there should be a test to cover this, but I'm not quite sure how
to fake this.
Signed-off-by: Simon Glass <sjg@chromium.org>
(fixed up missing ReadChildData() enty test)
Simon Glass [Sat, 24 Aug 2019 13:22:43 +0000 (07:22 -0600)]
binman: Use cls instead of self for class methods
It is more common to use the name 'cls' for the class object of a class
method, to distinguish it from normal methods, which use 'self' Update the
binman tests accordingly.
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Sat, 24 Aug 2019 13:22:42 +0000 (07:22 -0600)]
patman: Update command.Run() to handle failure better
At present tools are not expected to fail. If they do an exception is
raised but there is no detail about what went wrong. This makes it hard
to debug if something does actually go wrong.
Fix this by outputting both stderr and stdout on failure.
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Sat, 24 Aug 2019 13:22:41 +0000 (07:22 -0600)]
patman: Drop binary parameter
Since cros_subprocess use bytestrings now, this feature not needed. Drop
it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tom Rini [Tue, 15 Oct 2019 01:00:10 +0000 (21:00 -0400)]
Merge branch 'master' of git://git.denx.de/u-boot-socfpga
- vining_fpga updates
Tom Rini [Mon, 14 Oct 2019 17:00:51 +0000 (13:00 -0400)]
Merge tag 'u-boot-imx-
20191014' of https://gitlab.denx.de/u-boot/custodians/u-boot-imx
u-boot-imx-
20191014
-------------------
Travis: https://travis-ci.org/sbabic/u-boot-imx/builds/
597498628
- logicpd pinmux
- i.MX7ULP: imx_ddr_size
- fixes Toradex i.MX6/i.MX7
- pico-imx7d
- tpc70 converted to DM
- New Board: meerkat96
- add HAB version command
- i.MX8 :
imx8: Jump from alias to OCRAM address at SPL init
imx8qm/qxp: Set SPL TEXT base to OCRAM base
Tom Rini [Mon, 14 Oct 2019 11:30:16 +0000 (07:30 -0400)]
Merge tag 'video-for-2020.01' of https://gitlab.denx.de/u-boot/custodians/u-boot-video
- panel bridge support in stm32 ltdc
- DSI host uclass
- sandbox DSI host uclass test driver and DSI host test
- MIPI DSI helpers
- Synopsys Designware MIPI DSI host bridge driver
- STM32 DSI controller driver
- OTM800A and RM68200 panel support
- DSI host updates for stm32f769 and stm32mp1 dtsi files
- splash screen for stm32f769 and stm32mp1 boards
- stm32 defconfig updates for display support
Tom Rini [Mon, 14 Oct 2019 11:28:32 +0000 (07:28 -0400)]
Merge tag 'mmc-10-10-2019' of https://gitlab.denx.de/u-boot/custodians/u-boot-mmc
- Add sdhci driver for Broadcom iProc platform
- Add a driver callback for power-cycle for mmc
- Implement host_power_cycle callback for stm32_sdmmc2
- spl: dm_mmc: Initialize only the required mmc device
Peng Fan [Wed, 24 Jul 2019 08:54:16 +0000 (08:54 +0000)]
i2c: imx_lpi2c: add ipg clk
The controller needs two clk, per clk and ipg clk,
so let's add ipg clk.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Sjoerd Simons [Tue, 18 Jun 2019 21:08:59 +0000 (23:08 +0200)]
imx :hab: Add hab version command
THe RVT data includes a major and minor version in its header
parameter. Add a new command to print this out.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Peng Fan [Wed, 9 Oct 2019 03:08:17 +0000 (03:08 +0000)]
imx: imx8mm_evk: add board_mmc_get_env_dev
Add board_mmc_get_env_dev to correctly return devno for mmc env
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Fabio Estevam [Thu, 18 Jul 2019 18:04:25 +0000 (15:04 -0300)]
mx7ulp_evk: Use imx_ddr_size()
Use imx_ddr_size() to retrieve the total DDR size instead
of passing a hardcoded memory size.
imx_ddr_size() calculates the memory size based on the actual
MMDC registers values and is useful to detect misconfigurations,
so switch to this more robust approach.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Fabio Estevam [Thu, 18 Jul 2019 18:04:24 +0000 (15:04 -0300)]
imx: mmdc_size: Allow building it for i.MX7ULP
i.MX7ULP uses the same MMDC controller IP as found on i.MX53
and i.MX6, so build mmdc_size.c for i.MX7ULP as well.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Fabio Estevam [Thu, 18 Jul 2019 18:04:23 +0000 (15:04 -0300)]
imx: mmdc_size: Fix checkpatch warnings
The original imx_ddr_size() implementation had some
issues reported by checkpatch like this:
CHECK: Prefer kernel type 'u32' over 'uint32_t'
#127: FILE: arch/arm/mach-imx/mmdc_size.c:16:
+ uint32_t ctl;
WARNING: Prefer 'unsigned int' to bare use of 'unsigned'
#151: FILE: arch/arm/mach-imx/mmdc_size.c:40:
+ unsigned ctl = readl(&mem->ctl);
Fix all of them.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Fabio Estevam [Thu, 18 Jul 2019 18:04:22 +0000 (15:04 -0300)]
imx: Place imx_ddr_size() into a separate file
Place imx_ddr_size() into a separate file.
The motivation for doing this is to be able to easily reuse
imx_ddr_size() on i.MX7ULP.
Currently imx_ddr_size() is inside arch/arm/mach-imx/cpu.c, which
is not built for i.MX7ULP.
Changing the logic to allow building cpu.c for i.MX7UP would
require adding several ifdef's, leading to a not a very elegant
solution.
To allow better reuse, just place imx_ddr_size() into a common
mmdc_size.c file.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Stefano Babic <sbabic@denx.de>
Yannick Fertré [Mon, 7 Oct 2019 13:29:15 +0000 (15:29 +0200)]
stm32mp1: configs: add display devices
Add support of panels otm8009A, RM68200 & DSI controller.
Limit resolution to 1280x800.
Signed-off-by: Yannick Fertré <yannick.fertre@st.com>
Yannick Fertré [Mon, 7 Oct 2019 13:29:14 +0000 (15:29 +0200)]
stm32mp1: configs: update video
Update video configs to support bitmap 16bpp, 24bpp,
32bpp & RLE8.
Signed-off-by: Yannick Fertré <yannick.fertre@st.com>
Yannick Fertré [Mon, 7 Oct 2019 13:29:13 +0000 (15:29 +0200)]
ARM: dts: stm32mp1: add dsi host for stm32mp157c-dk2 board
The new class dsi host allows the management of the bridge DPI to DSI.
This bridge is embedded in the chipset mp1 (come from synopsys company).
Signed-off-by: Yannick Fertré <yannick.fertre@st.com>
Yannick Fertré [Mon, 7 Oct 2019 13:29:12 +0000 (15:29 +0200)]
ARM: dts: stm32mp1: add dsi host for stm32mp157c-ev1 board
The new class dsi host allows the management of the bridge DPI to DSI.
This bridge is embedded in the chipset mp1 (come from synopsys company).
Signed-off-by: Yannick Fertré <yannick.fertre@st.com>
Yannick Fertré [Mon, 7 Oct 2019 13:29:11 +0000 (15:29 +0200)]
ARM: dts: stm32f769: add display for STM32F769 disco board
Enable the display controller, mipi dsi bridge & panel.
Set panel display timings.
Signed-off-by: Yannick Fertré <yannick.fertre@st.com>
Yannick Fertré [Mon, 7 Oct 2019 13:29:10 +0000 (15:29 +0200)]
board: Add STM32F769 SoC, discovery board support
Signed-off-by: Yannick Fertré <yannick.fertre@st.com>
Yannick Fertré [Mon, 7 Oct 2019 13:29:09 +0000 (15:29 +0200)]
video: add support of panel RM68200
Support for Raydium RM68200 720p dsi 2dl video mode panel.
This rm68200 panel driver is based on the Linux Kernel driver from
drivers/gpu/drm/panel/panel-raydium-rm68200.c.
Signed-off-by: Yannick Fertré <yannick.fertre@st.com>
Yannick Fertré [Mon, 7 Oct 2019 13:29:08 +0000 (15:29 +0200)]
video: add support of panel OTM8009A
Support for Orise Tech otm8009a 480p dsi 2dl video mode panel.
Signed-off-by: Yannick Fertré <yannick.fertre@st.com>
Yannick Fertré [Mon, 7 Oct 2019 13:29:07 +0000 (15:29 +0200)]
video: add support of STM32 MIPI DSI controller driver
Add the STM32 DSI controller driver that uses the Synopsys DesignWare
MIPI DSI host controller bridge.
Signed-off-by: Yannick Fertré <yannick.fertre@st.com>
Yannick Fertré [Mon, 7 Oct 2019 13:29:06 +0000 (15:29 +0200)]
video: add MIPI DSI host controller bridge
Add a Synopsys Designware MIPI DSI host bridge driver, based on the
Rockchip version from rockchip/dw-mipi-dsi.c with phy & bridge APIs.
Signed-off-by: Yannick Fertré <yannick.fertre@st.com>
Yannick Fertré [Mon, 7 Oct 2019 13:29:05 +0000 (15:29 +0200)]
dm: Add a dsi host uclass
Display Serial Interface (DSI) host can usefully be modelled
as their own uclass.
DSI defines a serial bus and a communication protocol
between the host and the device (panel, bridge).
Signed-off-by: Yannick Fertré <yannick.fertre@st.com>
Shyam Saini [Fri, 14 Jun 2019 07:35:34 +0000 (13:05 +0530)]
configs: icorem6: Enable nandbcb command
This also enables mtd configs which are required by nandbcb command.
This command would be used to configure boot control block(BCB) while
writing spl image on nand device.
Signed-off-by: Shyam Saini <shyam.saini@amarulasolutions.com>
Igor Opaniuk [Mon, 22 Jul 2019 09:05:06 +0000 (12:05 +0300)]
colibri_imx7: provide proper node name to pmic_get
Implementation of pmic_get() uses uclass_find_device_by_name(), which
behaviour was changed in
4213609cc7
("drivers: core: use strcmp when find device by name"). Now we have to
supply full node name with unit address.
Fixes boot issue:
U-Boot 2019.07-00788-g0ef6e69a1e-dirty (Jul 19 2019 - 15:27:02 +0300)
CPU: Freescale i.MX7D rev1.3 1000 MHz (running at 792 MHz)
CPU: Extended Commercial temperature grade (-20C to 105C) at 41C
Reset cause: POR
DRAM: 512 MiB
initcall sequence
9ffd3a4c failed at call
87803c61 (err=-19)
ERROR Please RESET the board
Fixes:
4213609cc7("drivers: core: use strcmp when find device by name")
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Sjoerd Simons [Tue, 18 Jun 2019 20:13:20 +0000 (22:13 +0200)]
spl, Makefile: Take external offset into account for fit images
When building a FIT image for SPL to load also take into account the
configured external offset. This allows the SPL to load the u-boot FIT
image correctly when configuring SECURE_BOOT on i.mx6 is enabled
(with CONFIG_FIT_EXTERNAL_OFFSET=0x3000).
Note this doesn't allow secure booting; but it does allow an unsigned
SPL/u-boot with secure boot support eanbled to boot on open device.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Igor Opaniuk [Fri, 11 Oct 2019 09:57:09 +0000 (12:57 +0300)]
colibri_imx7: remove legacy sdboot wrapper
Remove legacy sdboot wrapper as distroboot can be used instead.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Igor Opaniuk [Fri, 11 Oct 2019 09:57:08 +0000 (12:57 +0300)]
colibri_imx6: remove legacy sdboot wrapper
Remove legacy sdboot wrapper as distroboot can be used instead.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Igor Opaniuk [Fri, 11 Oct 2019 09:57:07 +0000 (12:57 +0300)]
colibri-imx6ull: remove legacy sdboot wrapper
Remove legacy sdboot wrapper as distroboot can be used instead.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Igor Opaniuk [Fri, 11 Oct 2019 09:57:06 +0000 (12:57 +0300)]
apalis_imx6: remove legacy sdboot wrapper
Remove legacy sdboot wrapper as distroboot can be used instead.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Ye Li [Fri, 12 Jul 2019 09:33:55 +0000 (09:33 +0000)]
imx8qm/qxp: Set SPL TEXT base to OCRAM base
Modify the SPL TEXT base from OCRAM alias to OCRAM base 0x100000, so
we can use full OCRAM not limit to 96KB
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Ye Li [Fri, 12 Jul 2019 09:33:52 +0000 (09:33 +0000)]
imx8: Jump from alias to OCRAM address at SPL init
When running SPL on iMX8, the A core starts at address 0
which is a alias to OCRAM 0x100000.
The alias only map first 96KB of OCRAM, so this require the
SPL size can't beyond 96KB. But when using SPL DM, the size increase
significantly and may exceed 96KB.
So to fix the problem, we will change SPL linker address to OCRAM
address 0x100000. And then jump to the absolute address not the PC relative
address for entering OCRAM.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Lukasz Majewski [Thu, 10 Oct 2019 14:11:30 +0000 (16:11 +0200)]
imx: config: Update KP's TPC70 config to support SWUpdate
This patch updates envs responsible for using USB pendrive as a
SWUpdate based tool for recovery and update.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Lukasz Majewski [Thu, 10 Oct 2019 14:11:29 +0000 (16:11 +0200)]
imx: tpc70: Convert TPC70 (imx6q) board to use DM/DTS in SPL and u-boot
This patch converts the TPC70 to use driver model and device tree
description in both SPL and u-boot proper.
Notable changes (DM/DTS conversion):
- PINCTRL{_IMX6}
- DM_I2C
- enable 'regulator' and 'pmic' commands
- DM_MMC and BLK (USDHC)
- DM_ETH
- DM WDT (including SYSRESET)
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Lukasz Majewski [Thu, 10 Oct 2019 14:11:28 +0000 (16:11 +0200)]
imx: dts: Add u-boot specific set of device tree properties for tpc70
This commit adds new file - imx6q-kp-u-boot.dtsi with a set of u-boot
specific properties for imx6q KP device.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Lukasz Majewski [Thu, 10 Oct 2019 14:11:27 +0000 (16:11 +0200)]
imx: tpc70: dts: Add TPC70 board (imx6q based) device tree description
This commit defines the TPC70 imx6q board with device tree description.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Lukasz Majewski [Thu, 10 Oct 2019 14:11:26 +0000 (16:11 +0200)]
imx: tpc70: led: Enable LED default state
This change sets the default state of LEDs on TPC70.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Lukasz Majewski [Thu, 10 Oct 2019 14:11:25 +0000 (16:11 +0200)]
imx: tpc70: cosmetic: Replace magic numbers when setting ENET clock
This is a cosmetic change, just to use proper define instead
of magic numbers.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Lukasz Majewski [Thu, 10 Oct 2019 14:11:24 +0000 (16:11 +0200)]
imx: tpc70: Add board_boot_order() to distinguish between eMMC and SD boot
The TPC70 can boot from SD card (debug/development) and eMMC (production).
The board_boot_order() function provides a run time check for the device
from which one wants to boot (it is selected by GPIO pins setup).
Moreover, a fallback to SD card is provided if the detection is not
possible or working properly.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Lukasz Majewski [Thu, 10 Oct 2019 14:11:23 +0000 (16:11 +0200)]
imx: tpc70: config: Update TPC70 config to support eMMC's boot0 SPL update
The TPC70 can boot from eMMC's boot0. This patch allows it to update
this HW partition's SPL.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Lukasz Majewski [Thu, 10 Oct 2019 14:11:22 +0000 (16:11 +0200)]
imx: tpc70: config: Add script commands to update u-boot and OE's wic
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Jun Nie [Tue, 16 Jul 2019 07:42:57 +0000 (15:42 +0800)]
pico-imx7d: Support distro boot for FIT image case
Support distro boot for pico imx7d in FIT image case.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Tested-by: Joris Offouga <offougajoris@gmail.com>
Jun Nie [Tue, 16 Jul 2019 07:42:56 +0000 (15:42 +0800)]
pico-imx7d: add config to enable CAAM
Add config to enable CAAM so that hardware random number generator
works.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Adam Ford [Wed, 9 Oct 2019 17:53:57 +0000 (12:53 -0500)]
ARM: imx6q_logic: Remove legacy pinmuxing code from board file.
With the OCRAM expanded to 256KB and the SPL_PINCTRL enabled with
-u-boot.dtsi entries to include the pinmuxing in SPL, the manual
code setting up the pinmux can go away.
This patch removes the legacy pinmuxing code from the board file.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Adam Ford [Wed, 9 Oct 2019 17:53:56 +0000 (12:53 -0500)]
ARM: imx6q_logic: Enable Pin muxing in SPL
With the 256KB of OCRAM available to SPL now, there should be
enough room to enable the pinmuxing in SPL from the device tree.
This patch enables SPL_PINCTRL et al and adds the serial and
usdhc pin mux references to the -u-boot.dtsi file so the pins can be
configured from the device tree.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Adam Ford [Wed, 9 Oct 2019 17:53:55 +0000 (12:53 -0500)]
ARM: imx6q_logic: Enable 256KB OCRAM
Since this board config only supports, the i.MX6D/i.MX6Q configurations,
256K of on-chip RAM is available which increases the space available
to SPL to help further reduce board code and further enable device tree
functions.
This patch enables 256K of RAM.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Soeren Moch [Thu, 10 Oct 2019 22:59:50 +0000 (00:59 +0200)]
board: tbs2910: Convert eth to driver model
So we can remove lots of legacy config code.
Signed-off-by: Soeren Moch <smoch@web.de>
Soeren Moch [Thu, 10 Oct 2019 22:59:49 +0000 (00:59 +0200)]
board: tbs2910: Convert pci to driver model
So we can get rid of legacy pci config code.
PCI_PNP is not required for this board, remove it to reduce the size of the
u-boot binary.
DM_PCI does not start the host controller automatically anymore. Do so
in preboot instead.
Signed-off-by: Soeren Moch <smoch@web.de>
Soeren Moch [Thu, 10 Oct 2019 22:59:48 +0000 (00:59 +0200)]
ARM: dts: imx6q-tbs2910: Sync devicetree with kernel 5.3
Signed-off-by: Soeren Moch <smoch@web.de>
Sjoerd Simons [Thu, 20 Jun 2019 20:34:35 +0000 (22:34 +0200)]
mx6: mx6sabre common: Use more conventional spelling of fdtfile
Both the distro boot configuration as well as the general pxe support
standardized on fdtfile as the variable to hold the dtb filename.
Adjust to follow that such that e.g. "pxe boot" will just work.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Shawn Guo [Sun, 7 Jul 2019 12:59:55 +0000 (20:59 +0800)]
Add i.MX7D based Meerkat96 board support
The Meerkat96 board, based on the NXP i.MX7D SoC, is a member of
96Boards community and complies with all Consumer Edition board
specifications.
https://www.novtech.com/products/meerkat96.html
https://www.96boards.org/product/imx7-96/
The initial supported/tested devices include:
- Debug serial
- SD
- USB Host (with Ethernet)
With these support, it's good enough for loading Linux Kernel from SD or
Ethernet over USB.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Tested-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Shawn Guo [Sun, 7 Jul 2019 12:59:54 +0000 (20:59 +0800)]
ARM: dts: import meerkat96 board support
It imports device tree source of meerkat96 board from Linux Kernel.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Yannick Fertré [Mon, 7 Oct 2019 13:29:04 +0000 (15:29 +0200)]
video: add support of MIPI DSI interface
Mipi_display.c contains a set of dsi helpers.
This file is a copy of file drm_mipi_dsi.c (linux kernel).
Signed-off-by: Yannick Fertré <yannick.fertre@st.com>
Yannick Fertré [Mon, 7 Oct 2019 13:29:03 +0000 (15:29 +0200)]
include: Add new DCS commands in the enum list
Adding new DCS commands which are specified in the
DCS 1.3 spec related to CABC.
Signed-off-by: Yannick Fertré <yannick.fertre@st.com>
Yannick Fertré [Mon, 7 Oct 2019 13:29:02 +0000 (15:29 +0200)]
video: stm32: stm32_ltdc: add bridge to display controller
Manage a bridge insert between the display controller & a panel.
Signed-off-by: Yannick Fertré <yannick.fertre@st.com>
Tom Rini [Sun, 13 Oct 2019 15:21:56 +0000 (11:21 -0400)]
travis: Exclude MIPS from the bcm job
We don't need to pull in anything from the MIPS job so exclude that from
the new bcm job and make it clear it's building only ARM.
Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Sat, 12 Oct 2019 14:52:48 +0000 (10:52 -0400)]
Merge https://gitlab.denx.de/u-boot/custodians/u-boot-x86
- Remember the device being emulated for Sandbox PCI
- Update Kconfig options for FSP 1.0
- Drop RESET_BASE and RESET_SEG_SIZE that are no longer used
Tom Rini [Sat, 12 Oct 2019 14:10:59 +0000 (10:10 -0400)]
Merge branch '2019-10-11-master-imports'
- Assorted cleanups
- FAT bugfixes
- mediatek platform updates
Tom Rini [Sat, 12 Oct 2019 14:09:13 +0000 (10:09 -0400)]
Merge branch '2019-10-11-ti-imports'
- Various improvements to dra7xx, keystone 3, am65x SoCs
- Platform updates
- remoteproc improvements
Marek Szyprowski [Wed, 2 Oct 2019 10:24:46 +0000 (12:24 +0200)]
cmd: itest: add support for .q size specifier
Add support for quad (64bits) memory access specifier.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Lukasz Majewski <lukma@denx.de>
Heinrich Schuchardt [Thu, 12 Sep 2019 17:19:30 +0000 (19:19 +0200)]
fs: fat: get_contents() always returns -1 for errors
If out of memory, return -1 and not -ENOMEM from get_contents().
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Heinrich Schuchardt [Thu, 12 Sep 2019 17:19:29 +0000 (19:19 +0200)]
fs: fat: treat invalid FAT clusters as errors
When hitting an invalid FAT cluster while reading a file always print an
error message and return an error code.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Tom Rini [Fri, 11 Oct 2019 20:28:47 +0000 (16:28 -0400)]
sandbox: Remove sandbox_noblk build
At this point, all drivers that do not use CONFIG_BLK are past their
migration deadlines, so remove this config as it's no longer helpful and
hinders enhancing block drivers.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Lukasz Majewski [Mon, 9 Sep 2019 10:06:46 +0000 (12:06 +0200)]
spl: Introduce SPL_DM_SPI Kconfig define
This define indicates if DM_SPI shall be supported in SPL. This allows
proper operation of DM converted SPI drivers in SPL, which use
#if !CONFIG_IS_ENABLED(DM_SPI) to also support not yet DM/DTS converted
boards.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Heinrich Schuchardt [Thu, 12 Sep 2019 17:09:26 +0000 (19:09 +0200)]
arm64: print instructions leading to exception
If an exception occurs in a loaded image and the relocation offset is
unknown, it is helpful to know the instructions pointed to by the
program counter. This patch adds the missing output.
A possible output is:
Code:
910c4021 aa1303e0 f9400662 d63f0040 (
e7f7defb)
The parentheses indicate the instruction causing the exception.
The output can be disassembled using scripts/decodecode:
echo 'Code:
90000360 9100b800 94002782 17ffff8f (
e7f7defb)' | \
ARCH=arm64 scripts/decodecode
Code:
90000360 9100b800 94002782 17ffff8f (
e7f7defb)
All code
========
0:
90000360 adrp x0, 0x6c000
4:
9100b800 add x0, x0, #0x2e
8:
94002782 bl 0x9e10
c:
17ffff8f b 0xfffffffffffffe48
10:*
e7f7defb .inst 0xe7f7defb ; undefined <-- trapping instruction
Code starting with the faulting instruction
===========================================
0:
e7f7defb .inst 0xe7f7defb ; undefined
We already have implemented the same for armv7.
For testing command 'exception undefined' can be used.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
T Karthik Reddy [Wed, 11 Sep 2019 13:39:53 +0000 (15:39 +0200)]
cmd: avoid decimal conversion
This patch uses auto instead of decimal in simple_strtoul().
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Rasmus Villemoes [Tue, 10 Sep 2019 08:51:54 +0000 (08:51 +0000)]
ARM: asm/io.h: remove redundant #if !defined(readb) block
readb is unconditionally defined earlier in io.h, so there's no point
checking whether it's undefined.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Rasmus Villemoes [Tue, 10 Sep 2019 08:51:53 +0000 (08:51 +0000)]
ARM: asm/io.h: kill off confusing #ifdef __mem_pci block
No ARM board seems to define __mem_pci - and if it did, one would get tons of
./arch/arm/include/asm/io.h:307:0: warning: "readl" redefined
warnings, because readl and friends are unconditionally defined
earlier in io.h. Moreover, the redefinitions lack the memory barriers
that the first definitions have. So I'm guessing this is practically
dead code.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Mans Rullgard [Tue, 3 Sep 2019 14:16:50 +0000 (16:16 +0200)]
spl: mmc: Add option to set eMMC HW boot partition
This change allows setting pre-defined eMMC boot partition for SPL eMMC
booting. It is necessary in the case when one wants to boot (through falcon
boot) from eMMC after loading SPL from other memory (like SPI-NOR).
Signed-off-by: Mans Rullgard <mans@mansr.com>
[lukma: Edit the commit message]
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Andreas Dannenberg <dannenberg@ti.com>
Mans Rullgard [Tue, 3 Sep 2019 14:17:17 +0000 (16:17 +0200)]
spl: mmc: Fix indentation in spl_mmc.c file
This fixes a wrongly indented block of code.
Signed-off-by: Mans Rullgard <mans@mansr.com>
[lukma: Make the commit message more verbose]
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Lokesh Vutla [Tue, 1 Oct 2019 05:11:01 +0000 (10:41 +0530)]
arm: dra7xx: Hang on any failure during IOdelay recalibration
If there is any failure during IOdelay recalibration sequence, IOs are
not guaranteed to behave as expected. So hang on any failure during the
sequence.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Lokesh Vutla [Tue, 1 Oct 2019 05:11:00 +0000 (10:41 +0530)]
arm: dra7xx: Fix error path in iodelay recalibration
When an error is reported in __recalibrate_iodelay_start(), de-isolation
of IO doesn't happen. Because of this, undefined behaviour is observed
on many peripherals without any error. So make sure io is out of isolation
at the end of iodelay recalibration.
Reported-by: Richard Woodruff <r-woodruff2@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Jarkko Nikula [Mon, 30 Sep 2019 17:42:21 +0000 (20:42 +0300)]
tao3530: Fix usage of mmc rescan
Currently "bootcmd" does not work as intended but instead prints MMC usage
information and goes directly to "nandboot".
Follow what the commit
669681104daa ("configs: Fix usage of mmc rescan")
does for other boards prior to support for TechNexion TAO3530 SoM was
added.
Signed-off-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Lokesh Vutla [Mon, 30 Sep 2019 12:54:06 +0000 (18:24 +0530)]
configs: am43xx_evm: Enable USB support
spl_dm_init is failing as usb to be probed with the following error:
"omap_dwc3@
483c0000: ret=-2"
Enable usb to make spl boot on am43xx devices
Reported-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Lokesh Vutla [Sun, 29 Sep 2019 12:07:58 +0000 (17:37 +0530)]
arm: dts: k3-j721e-common-proc-board: Mark main_uart0 as shared device
Main uart0 is used as debug console by both R5SPL and A72 bootloader and
Linux. So mark it as shared device so that power-domain request is
successful by both cores.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Tero Kristo [Fri, 27 Sep 2019 16:14:29 +0000 (19:14 +0300)]
board: ti: am335x-ice: Configure the CDCE913 clock synthesizer
AM335x-ICE boards contain the CDCE913 clock synthesizer, and their
reset crystal capacitance load value of 10pF is wrong leading into
lost packets in certain networking tests. Add DT data for this
device, and probe it from the board file to program the crystal
capacitance load value to 0pF to avoid any problems.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Tero Kristo [Fri, 27 Sep 2019 16:14:28 +0000 (19:14 +0300)]
board: ti: am43xx-idk: Configure the CDCE913 clock synthesizer
AM43xx-IDK boards contain the CDCE913 clock synthesizer, and their
reset crystal capacitance load value of 10pF is wrong leading into
lost packets in certain networking tests. Add DT data for this
device, and probe it from the board file to program the crystal
capacitance load value to 0pF to avoid any problems.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Tero Kristo [Fri, 27 Sep 2019 16:14:27 +0000 (19:14 +0300)]
board: ti: am57xx-idk: Configure the CDCE913 clock synthesizer
AM57xx-IDK boards contain the CDCE913 clock synthesizer, and their
reset crystal capacitance load value of 10pF is wrong leading into
lost packets in certain networking tests. Add DT data for this
device, and probe it from the board file to program the crystal
capacitance load value to 0pF to avoid any problems.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Tero Kristo [Fri, 27 Sep 2019 16:14:26 +0000 (19:14 +0300)]
clk: cdce9xx: add support for cdce9xx clock synthesizer
Add support for CDCE913/925/937/949 family of devices. These are modular
PLL-based low cost, high performance, programmable clock synthesizers,
multipliers and dividers. They generate up to 9 output clocks from a
single input frequency. The initial version of the driver does not
support programming of the PLLs, and thus they run in the bypass mode
only. The code is loosely based on the linux kernel cdce9xx driver.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Lokesh Vutla [Fri, 27 Sep 2019 08:02:15 +0000 (13:32 +0530)]
arm: k3: Use driver_name to get ti_sci handle
Use the driver name to get ti_sci handle rather than relying
on just the FIRMWARE uclass.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Lokesh Vutla [Fri, 27 Sep 2019 08:02:14 +0000 (13:32 +0530)]
configs: am65x_evm_a53: Enable DISPLAY_CPUINFO
Enable CONFIG_DISPLAY_CPUINFO so that cpuinfo is printed during boot.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Lokesh Vutla [Fri, 27 Sep 2019 08:02:13 +0000 (13:32 +0530)]
configs: j721e_evm_a72: Enable DISPLAY_CPUINFO
Enable CONFIG_DISPLAY_CPUINFO so that cpuinfo is printed during boot.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Lokesh Vutla [Fri, 27 Sep 2019 08:02:12 +0000 (13:32 +0530)]
board: am65x: Print board name and version during boot
Print the board name and ver along with the DT Model.
While at it print the ver for all the detected daughter cards.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Lokesh Vutla [Fri, 27 Sep 2019 08:02:11 +0000 (13:32 +0530)]
arm: k3: Add support for printing CPUINFO
Add support for printing CPU info for all K3 devices.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Lokesh Vutla [Wed, 25 Sep 2019 09:08:13 +0000 (14:38 +0530)]
configs: j721e_evm_a72: Disable PSCI_RESET
J721E uses TISCI protocol to reset the device and does not
support PSCI reset. So disable PSCI reset.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Lokesh Vutla [Wed, 25 Sep 2019 09:08:05 +0000 (14:38 +0530)]
configs: am65x_evm_a53: Disable PSCI_RESET
AM65x uses TISCI protocol to reset the device and does not
support PSCI reset. So disable PSCI reset.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Lokesh Vutla [Tue, 24 Sep 2019 07:47:16 +0000 (13:17 +0530)]
mmc: am654_sdhci: Drop a redundant power_domain_on in probe
Power-domain is enabled by default in device_probe. am654 mmc driver
is enabling power-domain again in probe. As the second call is
redundant, drop power_domain_on from probe.
Tested-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Andrew F. Davis [Tue, 17 Sep 2019 19:40:25 +0000 (15:40 -0400)]
configs: ti: Use addr_fit for run_fit environment variable
When running 'run_fit' the FIT file should have been loaded at
'addr_fit', although at this point they should be the same
use this variable instead of 'loadaddr'.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Moses Christopher [Tue, 17 Sep 2019 14:25:38 +0000 (14:25 +0000)]
am335x, guardian: adapt guardian board to DM
- update partition table - remove env partitions
- dts: add new interfaces (uart2, extra gpio-key)
remove unneeded entries
update nand timings for performance improvement
- defconfig: adapt configurations to suit DM
remove unneeded configs
- am335x_guardian.h: remove mmc boot
Signed-off-by: Moses Christopher <BollavarapuMoses.Christopher@in.bosch.com>
Reviewed-by: Tom Rini <trini@konsulko.com>