Anton Blanchard [Mon, 3 Sep 2012 16:47:56 +0000 (16:47 +0000)]
powerpc: Update DSCR on all CPUs when writing sysfs dscr_default
commit
1b6ca2a6fe56e7697d57348646e07df08f43b1bb upstream.
Writing to dscr_default in sysfs doesn't actually change the DSCR -
we rely on a context switch on each CPU to do the work. There is no
guarantee we will get a context switch in a reasonable amount of time
so fire off an IPI to force an immediate change.
This issue was found with the following test case:
http://ozlabs.org/~anton/junkcode/dscr_explicit_test.c
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Haren Myneni <haren@us.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dan Carpenter [Sat, 9 Jun 2012 16:10:27 +0000 (19:10 +0300)]
ftrace: Clear bits properly in reset_iter_read()
commit
70f77b3f7ec010ff9624c1f2e39a81babc9e2429 upstream.
There is a typo here where '&' is used instead of '|' and it turns the
statement into a noop. The original code is equivalent to:
iter->flags &= ~((1 << 2) & (1 << 4));
Link: http://lkml.kernel.org/r/20120609161027.GD6488@elgon.mountain
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sarah Sharp [Wed, 17 Oct 2012 20:44:06 +0000 (13:44 -0700)]
xhci: Extend Fresco Logic MSI quirk.
commit
bba18e33f25072ebf70fd8f7f0cdbf8cdb59a746 upstream.
Ali reports that plugging a device into the Fresco Logic xHCI host with
PCI device ID 1400 produces an IRQ error:
do_IRQ: 3.176 No irq handler for vector (irq -1)
Other early Fresco Logic host revisions don't support MSI, even though
their PCI config space claims they do. Extend the quirk to disabling
MSI to this chipset revision. Also enable the short transfer quirk,
since it's likely this revision also has that quirk, and it should be
harmless to enable.
04:00.0 0c03: 1b73:1400 (rev 01) (prog-if 30 [XHCI])
Subsystem: 1d5c:1000
Physical Slot: 3
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 51
Region 0: Memory at
d4600000 (32-bit, non-prefetchable) [size=64K]
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [68] MSI: Enable+ Count=1/1 Maskable- 64bit+
Address:
00000000feeff00c Data: 41b1
Capabilities: [80] Express (v1) Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <2us, L1 <32us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 unlimited, L1 unlimited
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
Kernel driver in use: xhci_hcd
This patch should be backported to stable kernels as old as 2.6.36, that
contain the commit
f5182b4155b9d686c5540a6822486400e34ddd98 "xhci:
Disable MSI for some Fresco Logic hosts."
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-by: A Sh <smr.ash1991@gmail.com>
Tested-by: A Sh <smr.ash1991@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alan Stern [Mon, 26 Nov 2012 17:36:21 +0000 (12:36 -0500)]
USB: OHCI: workaround for hardware bug: retired TDs not added to the Done Queue
commit
50ce5c0683aa83eb161624ea89daa5a9eee0c2ce upstream.
This patch (as1636) is a partial workaround for a hardware bug
affecting OHCI controllers by NVIDIA at least, maybe others too. When
the controller retires a Transfer Descriptor, it is supposed to add
the TD onto the Done Queue. But sometimes this doesn't happen, with
the result that ohci-hcd never realizes the corresponding transfer has
finished. Symptoms can vary; a typical result is that USB audio stops
working after a while.
The patch works around the problem by recognizing that TDs are always
processed in order. Therefore, if a later TD is found on the Done
Queue than all the earlier TDs for the same endpoint must be finished
as well.
Unfortunately this won't solve the problem in cases where the missing
TD is the last one in the endpoint's queue. A complete fix would
require a signficant amount of change to the driver.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Zhang Rui [Tue, 4 Dec 2012 22:30:19 +0000 (23:30 +0100)]
ACPI / video: ignore BIOS initial backlight value for HP Folio 13-2000
commit
129ff8f8d58297b04f47b5d6fad81aa2d08404e1 upstream.
Or else the laptop will boot with a dimmed screen.
References: https://bugzilla.kernel.org/show_bug.cgi?id=51141
Tested-by: Stefan Nagy <public@stefan-nagy.at>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rafael J. Wysocki [Fri, 30 Nov 2012 12:05:05 +0000 (13:05 +0100)]
ACPI / PNP: Do not crash due to stale pointer use during system resume
commit
a6b5e88c0e42093b9057856f35770966c8c591e3 upstream.
During resume from system suspend the 'data' field of
struct pnp_dev in pnpacpi_set_resources() may be a stale pointer,
due to removal of the associated ACPI device node object in the
previous suspend-resume cycle. This happens, for example, if a
dockable machine is booted in the docking station and then suspended
and resumed and suspended again. If that happens,
pnpacpi_build_resource_template() called from pnpacpi_set_resources()
attempts to use that pointer and crashes.
However, pnpacpi_set_resources() actually checks the device's ACPI
handle, attempts to find the ACPI device node object attached to it
and returns an error code if that fails, so in fact it knows what the
correct value of dev->data should be. Use this observation to update
dev->data with the correct value if necessary and dump a call trace
if that's the case (once).
We still need to fix the root cause of this issue, but preventing
systems from crashing because of it is an improvement too.
Reported-and-tested-by: Zdenek Kabelac <zdenek.kabelac@gmail.com>
References: https://bugzilla.kernel.org/show_bug.cgi?id=51071
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Kamil Iskra [Fri, 16 Nov 2012 21:28:58 +0000 (22:28 +0100)]
ACPI / battery: Correct battery capacity values on Thinkpads
commit
4000e626156935dfb626321ce09cae2c833eabbb upstream.
Add a quirk to correctly report battery capacity on 2010 and 2011
Lenovo Thinkpad models.
The affected models that I tested (x201, t410, t410s, and x220)
exhibit a problem where, when battery capacity reporting unit is mAh,
the values being reported are wrong. Pre-2010 and 2012 models appear
to always report in mWh and are thus unaffected. Also, in mid-2012
Lenovo issued a BIOS update for the 2011 models that fixes the issue
(tested on x220 with a post-1.29 BIOS). No such update is available
for the 2010 models, so those still need this patch.
Problem description: for some reason, the affected Thinkpads switch
the reporting unit between mAh and mWh; generally, mAh is used when a
laptop is plugged in and mWh when it's unplugged, although a
suspend/resume or rmmod/modprobe is needed for the switch to take
effect. The values reported in mAh are *always* wrong. This does
not appear to be a kernel regression; I believe that the values were
never reported correctly. I tested back to kernel 2.6.34, with
multiple machines and BIOS versions.
Simply plugging a laptop into mains before turning it on is enough to
reproduce the problem. Here's a sample /proc/acpi/battery/BAT0/info
from Thinkpad x220 (before a BIOS update) with a 4-cell battery:
present: yes
design capacity: 2886 mAh
last full capacity: 2909 mAh
battery technology: rechargeable
design voltage: 14800 mV
design capacity warning: 145 mAh
design capacity low: 13 mAh
cycle count: 0
capacity granularity 1: 1 mAh
capacity granularity 2: 1 mAh
model number: 42T4899
serial number: 21064
battery type: LION
OEM info: SANYO
Once the laptop switches the unit to mWh (unplug from mains, suspend,
resume), the output changes to:
present: yes
design capacity: 28860 mWh
last full capacity: 29090 mWh
battery technology: rechargeable
design voltage: 14800 mV
design capacity warning: 1454 mWh
design capacity low: 200 mWh
cycle count: 0
capacity granularity 1: 1 mWh
capacity granularity 2: 1 mWh
model number: 42T4899
serial number: 21064
battery type: LION
OEM info: SANYO
Can you see how the values for "design capacity", etc., differ by a
factor of 10 instead of 14.8 (the design voltage of this battery)?
On the battery itself it says: 14.8V, 1.95Ah, 29Wh, so clearly the
values reported in mWh are correct and the ones in mAh are not.
My guess is that this problem has been around ever since those
machines were released, but because the most common Thinkpad
batteries are rated at 10.8V, the error (8%) is small enough that it
simply hasn't been noticed or at least nobody could be bothered to
look into it.
My patch works around the problem by adjusting the incorrectly
reported mAh values by "10000 / design_voltage". The patch also has
code to figure out if it should be activated or not. It only
activates on Lenovo Thinkpads, only when the unit is mAh, and, as an
extra precaution, only when the battery capacity reported through
ACPI does not match what is reported through DMI (I've never
encountered a machine where the first two conditions would be true
but the last would not, but better safe than sorry).
I've been using this patch for close to a year on several systems
without any problems.
References: https://bugzilla.kernel.org/show_bug.cgi?id=41062
Acked-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Greg Kroah-Hartman [Wed, 28 Nov 2012 18:19:16 +0000 (10:19 -0800)]
USB: mark uas driver as BROKEN
commit
fb37ef98015f864d22be223a0e0d93547cd1d4ef upstream.
As reported https://bugzilla.kernel.org/show_bug.cgi?id=51031, the UAS
driver causes problems and has been asked to be not built into any of
the major distributions. To prevent users from running into problems
with it, and for distros that were not notified, just mark the whole
thing as broken.
Acked-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Markus Becker [Thu, 22 Nov 2012 08:41:23 +0000 (09:41 +0100)]
USB: cp210x: add Virtenio Preon32 device id
commit
356fe44f4b8ece867bdb9876b1854d7adbef9de2 upstream.
Signed-off-by: Markus Becker <mab@comnets.uni-bremen.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Peter Korsgaard [Thu, 22 Nov 2012 15:30:46 +0000 (16:30 +0100)]
usb: ftdi_sio: fixup BeagleBone A5+ quirk
commit
1a88d5eee2ef2ad1d3c4e32043e9c4c5347d4fc1 upstream.
BeagleBone A5+ devices ended up getting shipped with the
'BeagleBone/XDS100V2' product string, and not XDS100 like it
was agreed, so adjust the quirk to match.
For details, see the thread on the beagle list:
https://groups.google.com/forum/#!msg/beagleboard/zrFPew9_Wvo/ibWr1-eE8JwJ
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Martin Teichmann [Wed, 21 Nov 2012 15:45:07 +0000 (16:45 +0100)]
USB: ftdi_sio: Add support for Newport AGILIS motor drivers
commit
d7e14b375b40c04cd735b115713043b69a2c68ac upstream.
The Newport AGILIS model AG-UC8 compact piezo motor controller
(http://search.newport.com/?q=*&x2=sku&q2=AG-UC8)
is yet another device using an FTDI USB-to-serial chip. It works
fine with the ftdi_sio driver when adding
options ftdi-sio product=0x3000 vendor=0x104d
to modprobe.d. udevadm reports "Newport" as the manufacturer,
and "Agilis" as the product name.
Signed-off-by: Martin Teichmann <lkb.teichmann@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Bjørn Mork [Sun, 25 Nov 2012 16:05:10 +0000 (17:05 +0100)]
USB: option: blacklist network interface on Huawei E173
commit
f36446cf9bbebaa03a80d95cfeeafbaf68218249 upstream.
The Huawei E173 will normally appear as 12d1:1436 in Linux. But
the modem has another mode with different device ID and a slightly
different set of descriptors. This is the mode used by Windows like
this:
3Modem: USB\VID_12D1&PID_140C&MI_00\6&
3A1D2012&0&0000
Networkcard: USB\VID_12D1&PID_140C&MI_01\6&
3A1D2012&0&0001
Appli.Inter: USB\VID_12D1&PID_140C&MI_02\6&
3A1D2012&0&0002
PC UI Inter: USB\VID_12D1&PID_140C&MI_03\6&
3A1D2012&0&0003
All interfaces have the same ff/ff/ff class codes in this mode.
Blacklisting the network interface to allow it to be picked up by
the network driver.
Reported-by: Thomas Schäfer <tschaefer@t-online.de>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
li.rui27@zte.com.cn [Tue, 20 Nov 2012 06:31:47 +0000 (14:31 +0800)]
USB: add new zte 3g-dongle's pid to option.c
commit
31b6a1048b7292efff8b5b53ae3d9d29adde385e upstream.
Signed-off-by: Rui li <li.rui27@zte.com.cn>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jan Beulich [Fri, 2 Nov 2012 14:02:40 +0000 (14:02 +0000)]
x86: hpet: Fix masking of MSI interrupts
commit
6acf5a8c931da9d26c8dd77d784daaf07fa2bff0 upstream.
HPET_TN_FSB is not a proper mask bit; it merely toggles between MSI and
legacy interrupt delivery. The proper mask bit is HPET_TN_ENABLE, so
use both bits when (un)masking the interrupt.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Link: http://lkml.kernel.org/r/5093E09002000078000A60E6@nat28.tlf.novell.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mel Gorman [Wed, 5 Dec 2012 22:01:41 +0000 (14:01 -0800)]
tmpfs: fix shared mempolicy leak
commit
18a2f371f5edf41810f6469cb9be39931ef9deb9 upstream.
This fixes a regression in 3.7-rc, which has since gone into stable.
Commit
00442ad04a5e ("mempolicy: fix a memory corruption by refcount
imbalance in alloc_pages_vma()") changed get_vma_policy() to raise the
refcount on a shmem shared mempolicy; whereas shmem_alloc_page() went
on expecting alloc_page_vma() to drop the refcount it had acquired.
This deserves a rework: but for now fix the leak in shmem_alloc_page().
Hugh: shmem_swapin() did not need a fix, but surely it's clearer to use
the same refcounting there as in shmem_alloc_page(), delete its onstack
mempolicy, and the strange mpol_cond_copy() and __mpol_cond_copy() -
those were invented to let swapin_readahead() make an unknown number of
calls to alloc_pages_vma() with one mempolicy; but since
00442ad04a5e,
alloc_pages_vma() has kept refcount in balance, so now no problem.
Reported-and-tested-by: Tommi Rantala <tt.rantala@gmail.com>
Signed-off-by: Mel Gorman <mgorman@suse.de>
Signed-off-by: Hugh Dickins <hughd@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dan Carpenter [Mon, 3 Dec 2012 19:05:12 +0000 (22:05 +0300)]
telephony: ijx: buffer overflow in ixj_write_cid()
[Not needed in 3.8 or newer as this driver is removed there. - gregkh]
We get this from user space and nothing has been done to ensure that
these strings are NUL terminated.
Reported-by: Chen Gang <gang.chen@asianux.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Boris Ostrovsky [Wed, 5 Dec 2012 11:12:42 +0000 (06:12 -0500)]
x86,AMD: Power driver support for AMD's family 16h processors
commit
22e32f4f57778ebc6e17812fa3008361c05d64f9 upstream.
Add family 16h PCI ID to AMD's power driver to allow it report
power consumption on these processors.
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@amd.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Marek Szyprowski [Wed, 7 Nov 2012 14:37:07 +0000 (15:37 +0100)]
mm: dmapool: use provided gfp flags for all dma_alloc_coherent() calls
commit
387870f2d6d679746020fa8e25ef786ff338dc98 upstream.
dmapool always calls dma_alloc_coherent() with GFP_ATOMIC flag,
regardless the flags provided by the caller. This causes excessive
pruning of emergency memory pools without any good reason. Additionaly,
on ARM architecture any driver which is using dmapools will sooner or
later trigger the following error:
"ERROR: 256 KiB atomic DMA coherent pool is too small!
Please increase it with coherent_pool= kernel parameter!".
Increasing the coherent pool size usually doesn't help much and only
delays such error, because all GFP_ATOMIC DMA allocations are always
served from the special, very limited memory pool.
This patch changes the dmapool code to correctly use gfp flags provided
by the dmapool caller.
Reported-by: Soeren Moch <smoch@web.de>
Reported-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Soeren Moch <smoch@web.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tejun Heo [Tue, 4 Dec 2012 15:40:39 +0000 (07:40 -0800)]
workqueue: convert BUG_ON()s in __queue_delayed_work() to WARN_ON_ONCE()s
commit
fc4b514f2727f74a4587c31db87e0e93465518c3 upstream.
8852aac25e ("workqueue: mod_delayed_work_on() shouldn't queue timer on
0 delay") unexpectedly uncovered a very nasty abuse of delayed_work in
megaraid - it allocated work_struct, casted it to delayed_work and
then pass that into queue_delayed_work().
Previously, this was okay because 0 @delay short-circuited to
queue_work() before doing anything with delayed_work.
8852aac25e
moved 0 @delay test into __queue_delayed_work() after sanity check on
delayed_work making megaraid trigger BUG_ON().
Although megaraid is already fixed by
c1d390d8e6 ("megaraid: fix
BUG_ON() from incorrect use of delayed work"), this patch converts
BUG_ON()s in __queue_delayed_work() to WARN_ON_ONCE()s so that such
abusers, if there are more, trigger warning but don't crash the
machine.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Xiaotian Feng <xtfeng@gmail.com>
Signed-off-by: Shuah Khan <shuah.khan@hp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Benjamin Herrenschmidt [Mon, 26 Sep 2011 19:37:57 +0000 (19:37 +0000)]
powerpc/ptrace: Fix build with gcc 4.6
commit
e69b742a6793dc5bf16f6eedca534d4bc10d68b2 upstream.
gcc (rightfully) complains that we are accessing beyond the
end of the fpr array (we do, to access the fpscr).
The only sane thing to do (whether anything in that code can be
called remotely sane is debatable) is to special case fpscr and
handle it as a separate statement.
I initially tried to do it it by making the array access conditional
to index < PT_FPSCR and using a 3rd else leg but for some reason gcc
was unable to understand it and still spewed the warning.
So I ended up with something a tad more intricated but it seems to
build on 32-bit and on 64-bit with and without VSX.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Paul Walmsley [Tue, 23 Oct 2012 19:32:59 +0000 (20:32 +0100)]
ARM: 7566/1: vfp: fix save and restore when running on pre-VFPv3 and CONFIG_VFPv3 set
commit
39141ddfb63a664f26d3f42f64ee386e879b492c upstream.
After commit
846a136881b8f73c1f74250bf6acfaa309cab1f2 ("ARM: vfp: fix
saving d16-d31 vfp registers on v6+ kernels"), the OMAP 2430SDP board
started crashing during boot with omap2plus_defconfig:
[ 3.875122] mmcblk0: mmc0:e624 SD04G 3.69 GiB
[ 3.915954] mmcblk0: p1
[ 4.086639] Internal error: Oops - undefined instruction: 0 [#1] SMP ARM
[ 4.093719] Modules linked in:
[ 4.096954] CPU: 0 Not tainted (3.6.0-02232-g759e00b #570)
[ 4.103149] PC is at vfp_reload_hw+0x1c/0x44
[ 4.107666] LR is at __und_usr_fault_32+0x0/0x8
It turns out that the context save/restore fix unmasked a latent bug
in commit
5aaf254409f8d58229107b59507a8235b715a960 ("ARM: 6203/1: Make
VFPv3 usable on ARMv6"). When CONFIG_VFPv3 is set, but the kernel is
booted on a pre-VFPv3 core, the code attempts to save and restore the
d16-d31 VFP registers. These are only present on non-D16 VFPv3+, so
this results in an undefined instruction exception. The code didn't
crash before commit 846a136 because the save and restore code was
only touching d0-d15, present on all VFP.
Fix by implementing a request from Russell King to add a new HWCAP
flag that affirmatively indicates the presence of the d16-d31
registers:
http://marc.info/?l=linux-arm-kernel&m=
135013547905283&w=2
and some feedback from Måns to clarify the name of the HWCAP flag.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Dave Martin <dave.martin@linaro.org>
Cc: Måns Rullgård <mans.rullgard@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Greg Kroah-Hartman [Mon, 10 Dec 2012 18:45:23 +0000 (10:45 -0800)]
Linux 3.0.56
Jan Kara [Fri, 15 Jun 2012 10:52:46 +0000 (12:52 +0200)]
scsi: Silence unnecessary warnings about ioctl to partition
commit
6d9359280753d2955f86d6411047516a9431eb51 upstream.
Sometimes, warnings about ioctls to partition happen often enough that they
form majority of the warnings in the kernel log and users complain. In some
cases warnings are about ioctls such as SG_IO so it's not good to get rid of
the warnings completely as they can ease debugging of userspace problems
when ioctl is refused.
Since I have seen warnings from lots of commands, including some proprietary
userspace applications, I don't think disallowing the ioctls for processes
with CAP_SYS_RAWIO will happen in the near future if ever. So lets just
stop warning for processes with CAP_SYS_RAWIO for which ioctl is allowed.
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
CC: James Bottomley <JBottomley@parallels.com>
CC: linux-scsi@vger.kernel.org
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Cc: Satoru Takeuchi <satoru.takeuchi@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Chris Wilson [Thu, 18 Oct 2012 20:07:01 +0000 (21:07 +0100)]
drm/i915: Add no-lvds quirk for Supermicro X7SPA-H
commit
c31407a3672aaebb4acddf90944a114fa5c8af7b upstream.
Reported-and-tested-by: Francois Tigeot <ftigeot@wolfpond.org>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=55375
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Calvin Walton [Fri, 24 Aug 2012 11:56:31 +0000 (07:56 -0400)]
i915: Quirk no_lvds on Gigabyte GA-D525TUD ITX motherboard
commit
a51d4ed01e5bb39d2cf36a12f9976ab08872c192 upstream.
This board is incorrectly detected as having an LVDS connector,
resulting in the VGA output (the only available output on the board)
showing the console only in the top-left 1024x768 pixels, and an extra
LVDS connector appearing in X.
It's a desktop Mini-ITX board using an Atom D525 CPU with an NM10
chipset.
I've had this board for about a year, but this is the first time I
noticed the issue because I've been running it headless for most of its
life.
Signed-off-by: Calvin Walton <calvin.walton@kepstin.ca>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alan Cox [Thu, 25 Oct 2012 23:05:56 +0000 (01:05 +0200)]
ACPI: missing break
commit
879dca019dc43a1622edca3e7dde644b14b5acc5 upstream.
We handle NOTIFY_THROTTLING so don't then fall through to unsupported event.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Michal Kubecek [Tue, 4 Dec 2012 10:09:13 +0000 (11:09 +0100)]
route: release dst_entry.hh_cache when handling redirects
Stable-3.0 commit
42ab5316 (ipv4: fix redirect handling) was
backport of mainline commit
9cc20b26 from 3.2-rc3 where hh
member of struct dst_entry was already gone.
However, in 3.0 we still have it and we have to clean it as
well, otherwise it keeps pointing to the cleaned up (and
unusable) hh_cache entry and packets cannot be sent out.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mike Galbraith [Mon, 3 Dec 2012 05:25:25 +0000 (06:25 +0100)]
Revert "sched, autogroup: Stop going ahead if autogroup is disabled"
commit
fd8ef11730f1d03d5d6555aa53126e9e34f52f12 upstream.
This reverts commit
800d4d30c8f20bd728e5741a3b77c4859a613f7c.
Between commits
8323f26ce342 ("sched: Fix race in task_group()") and
800d4d30c8f2 ("sched, autogroup: Stop going ahead if autogroup is
disabled"), autogroup is a wreck.
With both applied, all you have to do to crash a box is disable
autogroup during boot up, then reboot.. boom, NULL pointer dereference
due to commit
800d4d30c8f2 not allowing autogroup to move things, and
commit
8323f26ce342 making that the only way to switch runqueues:
BUG: unable to handle kernel NULL pointer dereference at (null)
IP: [<
ffffffff81063ac0>] effective_load.isra.43+0x50/0x90
Pid: 7047, comm: systemd-user-se Not tainted 3.6.8-smp #7 MEDIONPC MS-7502/MS-7502
RIP: effective_load.isra.43+0x50/0x90
Process systemd-user-se (pid: 7047, threadinfo
ffff880221dde000, task
ffff88022618b3a0)
Call Trace:
select_task_rq_fair+0x255/0x780
try_to_wake_up+0x156/0x2c0
wake_up_state+0xb/0x10
signal_wake_up+0x28/0x40
complete_signal+0x1d6/0x250
__send_signal+0x170/0x310
send_signal+0x40/0x80
do_send_sig_info+0x47/0x90
group_send_sig_info+0x4a/0x70
kill_pid_info+0x3a/0x60
sys_kill+0x97/0x1a0
? vfs_read+0x120/0x160
? sys_read+0x45/0x90
system_call_fastpath+0x16/0x1b
Code: 49 0f af 41 50 31 d2 49 f7 f0 48 83 f8 01 48 0f 46 c6 48 2b 07 48 8b bf 40 01 00 00 48 85 ff 74 3a 45 31 c0 48 8b 8f 50 01 00 00 <48> 8b 11 4c 8b 89 80 00 00 00 49 89 d2 48 01 d0 45 8b 59 58 4c
RIP [<
ffffffff81063ac0>] effective_load.isra.43+0x50/0x90
RSP <
ffff880221ddfbd8>
CR2:
0000000000000000
Signed-off-by: Mike Galbraith <efault@gmx.de>
Acked-by: Ingo Molnar <mingo@kernel.org>
Cc: Yong Zhang <yong.zhang0@gmail.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mike Galbraith [Wed, 28 Nov 2012 06:17:18 +0000 (07:17 +0100)]
workqueue: exit rescuer_thread() as TASK_RUNNING
commit
412d32e6c98527078779e5b515823b2810e40324 upstream.
A rescue thread exiting TASK_INTERRUPTIBLE can lead to a task scheduling
off, never to be seen again. In the case where this occurred, an exiting
thread hit reiserfs homebrew conditional resched while holding a mutex,
bringing the box to its knees.
PID: 18105 TASK:
ffff8807fd412180 CPU: 5 COMMAND: "kdmflush"
#0 [
ffff8808157e7670] schedule at
ffffffff8143f489
#1 [
ffff8808157e77b8] reiserfs_get_block at
ffffffffa038ab2d [reiserfs]
#2 [
ffff8808157e79a8] __block_write_begin at
ffffffff8117fb14
#3 [
ffff8808157e7a98] reiserfs_write_begin at
ffffffffa0388695 [reiserfs]
#4 [
ffff8808157e7ad8] generic_perform_write at
ffffffff810ee9e2
#5 [
ffff8808157e7b58] generic_file_buffered_write at
ffffffff810eeb41
#6 [
ffff8808157e7ba8] __generic_file_aio_write at
ffffffff810f1a3a
#7 [
ffff8808157e7c58] generic_file_aio_write at
ffffffff810f1c88
#8 [
ffff8808157e7cc8] do_sync_write at
ffffffff8114f850
#9 [
ffff8808157e7dd8] do_acct_process at
ffffffff810a268f
[exception RIP: kernel_thread_helper]
RIP:
ffffffff8144a5c0 RSP:
ffff8808157e7f58 RFLAGS:
00000202
RAX:
0000000000000000 RBX:
0000000000000000 RCX:
0000000000000000
RDX:
0000000000000000 RSI:
ffffffff8107af60 RDI:
ffff8803ee491d18
RBP:
0000000000000000 R8:
0000000000000000 R9:
0000000000000000
R10:
0000000000000000 R11:
0000000000000000 R12:
0000000000000000
R13:
0000000000000000 R14:
0000000000000000 R15:
0000000000000000
ORIG_RAX:
ffffffffffffffff CS: 0010 SS: 0018
Signed-off-by: Mike Galbraith <mgalbraith@suse.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Naoya Horiguchi [Thu, 29 Nov 2012 21:54:34 +0000 (13:54 -0800)]
mm: soft offline: split thp at the beginning of soft_offline_page()
commit
783657a7dc20e5c0efbc9a09a9dd38e238a723da upstream.
When we try to soft-offline a thp tail page, put_page() is called on the
tail page unthinkingly and VM_BUG_ON is triggered in put_compound_page().
This patch splits thp before going into the main body of soft-offlining.
Signed-off-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Andi Kleen <andi.kleen@intel.com>
Cc: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jianguo Wu [Thu, 29 Nov 2012 21:54:21 +0000 (13:54 -0800)]
mm/vmemmap: fix wrong use of virt_to_page
commit
ae64ffcac35de0db628ba9631edf8ff34c5cd7ac upstream.
I enable CONFIG_DEBUG_VIRTUAL and CONFIG_SPARSEMEM_VMEMMAP, when doing
memory hotremove, there is a kernel BUG at arch/x86/mm/physaddr.c:20.
It is caused by free_section_usemap()->virt_to_page(), virt_to_page() is
only used for kernel direct mapping address, but sparse-vmemmap uses
vmemmap address, so it is going wrong here.
------------[ cut here ]------------
kernel BUG at arch/x86/mm/physaddr.c:20!
invalid opcode: 0000 [#1] SMP
Modules linked in: acpihp_drv acpihp_slot edd cpufreq_conservative cpufreq_userspace cpufreq_powersave acpi_cpufreq mperf fuse vfat fat loop dm_mod coretemp kvm crc32c_intel ipv6 ixgbe igb iTCO_wdt i7core_edac edac_core pcspkr iTCO_vendor_support ioatdma microcode joydev sr_mod i2c_i801 dca lpc_ich mfd_core mdio tpm_tis i2c_core hid_generic tpm cdrom sg tpm_bios rtc_cmos button ext3 jbd mbcache usbhid hid uhci_hcd ehci_hcd usbcore usb_common sd_mod crc_t10dif processor thermal_sys hwmon scsi_dh_alua scsi_dh_hp_sw scsi_dh_rdac scsi_dh_emc scsi_dh ata_generic ata_piix libata megaraid_sas scsi_mod
CPU 39
Pid: 6454, comm: sh Not tainted 3.7.0-rc1-acpihp-final+ #45 QCI QSSC-S4R/QSSC-S4R
RIP: 0010:[<
ffffffff8103c908>] [<
ffffffff8103c908>] __phys_addr+0x88/0x90
RSP: 0018:
ffff8804440d7c08 EFLAGS:
00010006
RAX:
0000000000000006 RBX:
ffffea0012000000 RCX:
000000000000002c
...
Signed-off-by: Jianguo Wu <wujianguo@huawei.com>
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Reviewd-by: Wen Congyang <wency@cn.fujitsu.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Reviewed-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Reviewed-by: Michal Hocko <mhocko@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Russell King - ARM Linux [Sun, 18 Nov 2012 16:39:32 +0000 (16:39 +0000)]
Dove: Fix irq_to_pmu()
commit
d356cf5a74afa32b40decca3c9dd88bc3cd63eb5 upstream.
PMU interrupts start at IRQ_DOVE_PMU_START, not IRQ_DOVE_PMU_START + 1.
Fix the condition. (It may have been less likely to occur had the code
been written "if (irq >= IRQ_DOVE_PMU_START" which imho is the easier
to understand notation, and matches the normal way of thinking about
these things.)
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Russell King - ARM Linux [Sun, 18 Nov 2012 16:29:44 +0000 (16:29 +0000)]
Dove: Attempt to fix PMU/RTC interrupts
commit
5d3df935426271016b895aecaa247101b4bfa35e upstream.
Fix the acknowledgement of PMU interrupts on Dove: some Dove hardware
has not been sensibly designed so that interrupts can be handled in a
race free manner. The PMU is one such instance.
The pending (aka 'cause') register is a bunch of RW bits, meaning that
these bits can be both cleared and set by software (confirmed on the
Armada-510 on the cubox.)
Hardware sets the appropriate bit when an interrupt is asserted, and
software is required to clear the bits which are to be processed. If
we write ~(1 << bit), then we end up asserting every other interrupt
except the one we're processing. So, we need to do a read-modify-write
cycle to clear the asserted bit.
However, any interrupts which occur in the middle of this cycle will
also be written back as zero, which will also clear the new interrupts.
The upshot of this is: there is _no_ way to safely clear down interrupts
in this register (and other similarly behaving interrupt pending
registers on this device.) The patch below at least stops us creating
new interrupts.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Greg Kroah-Hartman [Thu, 6 Dec 2012 02:40:31 +0000 (18:40 -0800)]
Linux 3.0.55
H. Peter Anvin [Wed, 21 Nov 2012 06:21:02 +0000 (22:21 -0800)]
x86-32: Export kernel_stack_pointer() for modules
commit
cb57a2b4cff7edf2a4e32c0163200e9434807e0a upstream.
Modules, in particular oprofile (and possibly other similar tools)
need kernel_stack_pointer(), so export it using EXPORT_SYMBOL_GPL().
Cc: Yang Wei <wei.yang@windriver.com>
Cc: Robert Richter <robert.richter@amd.com>
Cc: Jun Zhang <jun.zhang@intel.com>
Link: http://lkml.kernel.org/r/20120912135059.GZ8285@erda.amd.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Cc: Robert Richter <rric@kernel.org>
Cc: Herton Ronaldo Krzesinski <herton.krzesinski@canonical.com>
Cc: Philip Müller <philm@manjaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Greg Kroah-Hartman [Mon, 3 Dec 2012 20:59:38 +0000 (12:59 -0800)]
Linux 3.0.54
Jaehoon Chung [Wed, 19 Sep 2012 06:43:33 +0000 (14:43 +0800)]
mmc: sdhci-s3c: fix the wrong number of max bus clocks
commit
5feb54a1ab91a237e247c013b8c4fb100ea347b1 upstream.
We can use up to four bus-clocks; but on module remove, we didn't
disable the fourth bus clock.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Cc: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jussi Pakkanen [Wed, 11 Jan 2012 07:04:16 +0000 (23:04 -0800)]
Input: bcm5974 - set BUTTONPAD property
commit
52965cc012f7a3cf35f06485ec275ebf3b3fddae upstream.
Some bcm5974 trackpads have a physical button beneath the physical surface.
This patch sets the property bit so user space applications can detect the
trackpad type and act accordingly.
Signed-off-by: Jussi Pakkanen <jussi.pakkanen@canonical.com>
Reviewed-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Cc: maximilian attems <max@stro.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fenghua Yu [Fri, 4 Nov 2011 20:31:23 +0000 (13:31 -0700)]
x86, mce, therm_throt: Don't report power limit and package level thermal throttle events in mcelog
commit
29e9bf1841e4f9df13b4992a716fece7087dd237 upstream.
Thermal throttle and power limit events are not defined as MCE errors in x86
architecture and should not generate MCE errors in mcelog.
Current kernel generates fake software defined MCE errors for these events.
This may confuse users because they may think the machine has real MCE errors
while actually only thermal throttle or power limit events happen.
To make it worse, buggy firmware on some platforms may falsely generate
the events. Therefore, kernel reports MCE errors which users think as real
hardware errors. Although the firmware bugs should be fixed, on the other hand,
kernel should not report MCE errors either.
So mcelog is not a good mechanism to report these events. To report the events, we count them in respective counters (core_power_limit_count,
package_power_limit_count, core_throttle_count, and package_throttle_count) in
/sys/devices/system/cpu/cpu#/thermal_throttle/. Users can check the counters
for each event on each CPU. Please note that all CPU's on one package report
duplicate counters. It's user application's responsibity to retrieve a package
level counter for one package.
This patch doesn't report package level power limit, core level power limit, and
package level thermal throttle events in mcelog. When the events happen, only
report them in respective counters in sysfs.
Since core level thermal throttle has been legacy code in kernel for a while and
users accepted it as MCE error in mcelog, core level thermal throttle is still
reported in mcelog. In the mean time, the event is counted in a counter in sysfs
as well.
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Acked-by: Borislav Petkov <bp@amd64.org>
Acked-by: Tony Luck <tony.luck@intel.com>
Link: http://lkml.kernel.org/r/20111215001945.GA21009@linux-os.sc.intel.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Cc: maximilian attems <max@stro.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Merlin Schumacher [Mon, 23 Jan 2012 20:35:35 +0000 (04:35 +0800)]
acer-wmi: support for P key on TM8372
commit
67e1d34cd54cbf33f093f1dd53e7bda1124eb972 upstream.
BugLink: http://launchpad.net/bugs/865807
There is no entry for P key on TM8372, so when P key is pressed, only
"acer_wmi: Unknown key number - 0x29" in dmesg.
Signed-off-by: Merlin Schumacher <merlin.schumacher@gmail.com>
Signed-off-by: Ike Panhc <ike.pan@canonical.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Cc: maximilian attems <max@stro.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Chuansheng Liu [Tue, 27 Nov 2012 00:29:54 +0000 (16:29 -0800)]
watchdog: using u64 in get_sample_period()
commit
8ffeb9b0e6369135bf03a073514f571ef10606b9 upstream.
In get_sample_period(), unsigned long is not enough:
watchdog_thresh * 2 * (NSEC_PER_SEC / 5)
case1:
watchdog_thresh is 10 by default, the sample value will be: 0xEE6B2800
case2:
set watchdog_thresh is 20, the sample value will be: 0x1 DCD6 5000
In case2, we need use u64 to express the sample period. Otherwise,
changing the threshold thru proc often can not be successful.
Signed-off-by: liu chuansheng <chuansheng.liu@intel.com>
Acked-by: Don Zickus <dzickus@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Shuah Khan <shuah.khan@hp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan Hovold [Thu, 25 Oct 2012 08:29:14 +0000 (10:29 +0200)]
USB: mct_u232: fix broken close
commit
5260e458f5eff269a43e4f1e9c47186c57b88ddb upstream.
Make sure generic close is called at close.
The driver relies on the generic write implementation but did not call
generic close.
Note that the call to kill the read urb is not redundant, as mct_u232
uses an interrupt urb from the second port as the read urb and that
generic close therefore fails to kill it.
Compile-only tested.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Mauro Carvalho Chehab [Fri, 28 Sep 2012 19:16:00 +0000 (16:16 -0300)]
get_dvb_firmware: fix download site for tda10046 firmware
commit
25ec43d3e6306978cf66060ed18c4160ce8fc302 upstream.
The previous website doesn't exist anymore. Update it to one site that
actually exists.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Emil Tantilov [Fri, 4 Nov 2011 06:43:29 +0000 (06:43 +0000)]
ixgbe: add support for new 82599 device id
commit
9e791e4a04c08868f02cd579a428a7268492e1b4 upstream.
Support for new 82599 based quad port adapter.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Abdallah Chatila <Abdallah.Chatila@ericsson.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Emil Tantilov [Thu, 8 Sep 2011 08:30:14 +0000 (08:30 +0000)]
ixgbe: add support for new 82599 device
commit
7d145282da8d1ae4ba5f7ead8a4f51183496803c upstream.
This patch adds support for new device ID.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Abdallah Chatila <Abdallah.Chatila@ericsson.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
David Milburn [Mon, 29 Oct 2012 23:00:22 +0000 (18:00 -0500)]
sata_svw: check DMA start bit before reset
commit
b03e66a6be91f8389fcd902ab6c1563db1c9c06b upstream.
If kdump is triggered with pending IO, controller may not respond causing
kdump to fail.
http://marc.info/?l=linux-ide&m=
133032255424658&w=2
During error recovery ata_do_dev_read_id never completes due hang
in mmio_insw.
ata_do_dev_read_id
ata_sff_data_xfer
ioread16_rep
mmio_insw
if DMA start bit is cleared before reset, PIO command is successful
and kdump succeeds.
Signed-off-by: David Milburn <dmilburn@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Cc: CAI Qian <caiqian@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
joshua.a.hay@intel.com [Fri, 21 Sep 2012 00:08:21 +0000 (00:08 +0000)]
ixgbe: add support for X540-AT1
commit
df376f0de167754da9b3ece4afdb5bb8bf3fbf3e upstream.
This patch adds device support for Ethernet Controller X540-AT1.
Signed-off-by: Josh Hay <joshua.a.hay@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Abdallah Chatila <Abdallah.Chatila@ericsson.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tilman Schmidt [Wed, 24 Oct 2012 08:44:32 +0000 (08:44 +0000)]
bas_gigaset: fix pre_reset handling
commit
c6fdd8e5d0c65bb8821dc6da26ee1a2ddd58b3cc upstream.
The delayed work function int_in_work() may call usb_reset_device()
and thus, indirectly, the driver's pre_reset method. Trying to
cancel the work synchronously in that situation would deadlock.
Fix by avoiding cancel_work_sync() in the pre_reset method.
If the reset was NOT initiated by int_in_work() this might cause
int_in_work() to run after the post_reset method, with urb_int_in
already resubmitted, so handle that case gracefully.
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
David Henningsson [Wed, 21 Nov 2012 07:57:58 +0000 (08:57 +0100)]
ALSA: hda - Add support for Realtek ALC292
commit
af02dde8a609d8d071c4b31a82df811a55690a4a upstream.
We found a new codec ID 292, and that just a simple quirk would enable
sound output/input on this ALC292 chip.
BugLink: https://bugs.launchpad.net/bugs/1081466
Tested-by: Acelan Kao <acelan.kao@canonical.com>
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Duncan Roe [Wed, 10 Oct 2012 12:19:50 +0000 (14:19 +0200)]
ALSA: hda - Fix missing beep on ASUS X43U notebook
commit
7110005e8d5c3cd418fc4b64f9f124f004422a9a upstream.
Signed-off-by: Duncan Roe <duncan_roe@acslink.net.au>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Kailang Yang [Sat, 6 Oct 2012 15:02:30 +0000 (17:02 +0200)]
ALSA: hda - Add new codec ALC283 ALC290 support
commit
7ff34ad80b7080fafaac8efa9ef0061708eddd51 upstream.
These are compatible with standard ALC269 parser.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Al Viro [Mon, 19 Nov 2012 03:27:03 +0000 (22:27 -0500)]
sparc64: not any error from do_sigaltstack() should fail rt_sigreturn()
commit
fae2ae2a900a5c7bb385fe4075f343e7e2d5daa2 upstream.
If a signal handler is executed on altstack and another signal comes,
we will end up with rt_sigreturn() on return from the second handler
getting -EPERM from do_sigaltstack(). It's perfectly OK, since we
are not asking to change the settings; in fact, they couldn't have been
changed during the second handler execution exactly because we'd been
on altstack all along. 64bit sigreturn on sparc treats any error from
do_sigaltstack() as "SIGSEGV now"; we need to switch to the same semantics
we are using on other architectures.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jan Kara [Fri, 23 Nov 2012 13:03:04 +0000 (14:03 +0100)]
jbd: Fix lock ordering bug in journal_unmap_buffer()
commit
25389bb207987b5774182f763b9fb65ff08761c8 upstream.
Commit
09e05d48 introduced a wait for transaction commit into
journal_unmap_buffer() in the case we are truncating a buffer undergoing commit
in the page stradding i_size on a filesystem with blocksize < pagesize. Sadly
we forgot to drop buffer lock before waiting for transaction commit and thus
deadlock is possible when kjournald wants to lock the buffer.
Fix the problem by dropping the buffer lock before waiting for transaction
commit. Since we are still holding page lock (and that is OK), buffer cannot
disappear under us.
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Oliver Hartkopp [Mon, 26 Nov 2012 21:24:23 +0000 (22:24 +0100)]
can: bcm: initialize ifindex for timeouts without previous frame reception
commit
81b401100c01d2357031e874689f89bd788d13cd upstream.
Set in the rx_ifindex to pass the correct interface index in the case of a
message timeout detection. Usually the rx_ifindex value is set at receive
time. But when no CAN frame has been received the RX_TIMEOUT notification
did not contain a valid value.
Reported-by: Andre Naujoks <nautsch2@googlemail.com>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Paul Bolle [Mon, 19 Nov 2012 20:17:31 +0000 (21:17 +0100)]
radeon: add AGPMode 1 quirk for RV250
commit
45171002b01b2e2ec4f991eca81ffd8430fd0aec upstream.
The Intel 82855PM host bridge / Mobility FireGL 9000 RV250 combination
in an (outdated) ThinkPad T41 needs AGPMode 1 for suspend/resume (under
KMS, that is). So add a quirk for it.
(Change R250 to RV250 in comment for preceding quirk too.)
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Simon Wunderlich [Tue, 13 Nov 2012 17:43:03 +0000 (18:43 +0100)]
mac80211: deinitialize ibss-internals after emptiness check
commit
b78a4932f5fb11fadf41e69c606a33fa6787574c upstream.
The check whether the IBSS is active and can be removed should be
performed before deinitializing the fields used for the check/search.
Otherwise, the configured BSS will not be found and removed properly.
To make it more clear for the future, rename sdata->u.ibss to the
local pointer ifibss which is used within the checks.
This behaviour was introduced by
f3209bea110cade12e2b133da8b8499689cb0e2e
("mac80211: fix IBSS teardown race")
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Cc: Ignacy Gawedzki <i@lri.fr>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Darren Hart [Tue, 27 Nov 2012 00:29:56 +0000 (16:29 -0800)]
futex: avoid wake_futex() for a PI futex_q
commit
aa10990e028cac3d5e255711fb9fb47e00700e35 upstream.
Dave Jones reported a bug with futex_lock_pi() that his trinity test
exposed. Sometime between queue_me() and taking the q.lock_ptr, the
lock_ptr became NULL, resulting in a crash.
While futex_wake() is careful to not call wake_futex() on futex_q's with
a pi_state or an rt_waiter (which are either waiting for a
futex_unlock_pi() or a PI futex_requeue()), futex_wake_op() and
futex_requeue() do not perform the same test.
Update futex_wake_op() and futex_requeue() to test for q.pi_state and
q.rt_waiter and abort with -EINVAL if detected. To ensure any future
breakage is caught, add a WARN() to wake_futex() if the same condition
is true.
This fix has seen 3 hours of testing with "trinity -c futex" on an
x86_64 VM with 4 CPUS.
[akpm@linux-foundation.org: tidy up the WARN()]
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
Reported-by: Dave Jones <davej@redat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: John Kacur <jkacur@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jens Axboe [Tue, 6 Nov 2012 11:24:26 +0000 (12:24 +0100)]
dm: fix deadlock with request based dm and queue request_fn recursion
commit
a8c32a5c98943d370ea606a2e7dc04717eb92206 upstream.
Request based dm attempts to re-run the request queue off the
request completion path. If used with a driver that potentially does
end_io from its request_fn, we could deadlock trying to recurse
back into request dispatch. Fix this by punting the request queue
run to kblockd.
Tested to fix a quickly reproducible deadlock in such a scenario.
Acked-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jiri Engelthaler [Thu, 20 Sep 2012 14:49:50 +0000 (16:49 +0200)]
mtd: slram: invalid checking of absolute end address
commit
c36a7ff4578ab6294885aef5ef241aeec4cdb1f0 upstream.
Fixed parsing end absolute address.
Signed-off-by: Jiri Engelthaler <engycz@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Al Viro [Wed, 21 Nov 2012 19:27:23 +0000 (19:27 +0000)]
PARISC: fix user-triggerable panic on parisc
commit
441a179dafc0f99fc8b3a8268eef66958621082e upstream.
int sys32_rt_sigprocmask(int how, compat_sigset_t __user *set, compat_sigset_t __user *oset,
unsigned int sigsetsize)
{
sigset_t old_set, new_set;
int ret;
if (set && get_sigset32(set, &new_set, sigsetsize))
...
static int
get_sigset32(compat_sigset_t __user *up, sigset_t *set, size_t sz)
{
compat_sigset_t s;
int r;
if (sz != sizeof *set) panic("put_sigset32()");
In other words, rt_sigprocmask(69, (void *)69, 69) done by 32bit process
will promptly panic the box.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
James Bottomley [Fri, 2 Nov 2012 12:30:53 +0000 (12:30 +0000)]
PARISC: fix virtual aliasing issue in get_shared_area()
commit
949a05d03490e39e773e8652ccab9157e6f595b4 upstream.
On Thu, 2012-11-01 at 16:45 -0700, Michel Lespinasse wrote:
> Looking at the arch/parisc/kernel/sys_parisc.c implementation of
> get_shared_area(), I do have a concern though. The function basically
> ignores the pgoff argument, so that if one creates a shared mapping of
> pages 0-N of a file, and then a separate shared mapping of pages 1-N
> of that same file, both will have the same cache offset for their
> starting address.
>
> This looks like this would create obvious aliasing issues. Am I
> misreading this ? I can't understand how this could work good enough
> to be undetected, so there must be something I'm missing here ???
This turns out to be correct and we need to pay attention to the pgoff as
well as the address when creating the virtual address for the area.
Fortunately, the bug is rarely triggered as most applications which use pgoff
tend to use large values (git being the primary one, and it uses pgoff in
multiples of 16MB) which are larger than our cache coherency modulus, so the
problem isn't often seen in practise.
Reported-by: Michel Lespinasse <walken@google.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Clemens Ladisch [Wed, 31 Oct 2012 15:35:30 +0000 (16:35 +0100)]
ALSA: ua101, usx2y: fix broken MIDI output
commit
e99ddfde6ae0dd2662bb40435696002b590e4057 upstream.
Commit
88a8516a2128 (ALSA: usbaudio: implement USB autosuspend) added
autosuspend code to all files making up the snd-usb-audio driver.
However, midi.c is part of snd-usb-lib and is also used by other
drivers, not all of which support autosuspend. Thus, calls to
usb_autopm_get_interface() could fail, and this unexpected error would
result in the MIDI output being completely unusable.
Make it work by ignoring the error that is expected with drivers that do
not support autosuspend.
Reported-by: Colin Fletcher <colin.m.fletcher@googlemail.com>
Reported-by: Devin Venable <venable.devin@gmail.com>
Reported-by: Dr Nick Bailey <nicholas.bailey@glasgow.ac.uk>
Reported-by: Jannis Achstetter <jannis_achstetter@web.de>
Reported-by: Rui Nuno Capela <rncbc@rncbc.org>
Cc: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Maciej Patelczyk [Mon, 15 Oct 2012 12:29:03 +0000 (14:29 +0200)]
SCSI: isci: copy fis 0x34 response into proper buffer
commit
49bd665c5407a453736d3232ee58f2906b42e83c upstream.
SATA MICROCODE DOWNALOAD fails on isci driver. After receiving Register
Device to Host (FIS 0x34) frame Initiator resets phy.
In the frame handler routine response (FIS 0x34) was copied into wrong
buffer and upper layer did not receive any answer which resulted in
timeout and reset.
This patch corrects this bug.
Signed-off-by: Maciej Patelczyk <maciej.patelczyk@intel.com>
Signed-off-by: Lukasz Dorau <lukasz.dorau@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Bing Zhao [Thu, 15 Nov 2012 23:58:48 +0000 (15:58 -0800)]
mwifiex: report error to MMC core if we cannot suspend
commit
dd321acddc3be1371263b8c9e6c6f2af89f63d57 upstream.
When host_sleep_config command fails we should return error to
MMC core to indicate the failure for our device.
The misspelled variable is also removed as it's redundant.
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Albert Pool [Tue, 30 Oct 2012 19:58:06 +0000 (20:58 +0100)]
rtlwifi: rtl8192cu: Add new USB ID
commit
a485e827f07bfdd0762059386e6e787bed6e81ee upstream.
This is an ISY IWL 2000. Probably a clone of Belkin F7D1102 050d:1102.
Its FCC ID is the same.
Signed-off-by: Albert Pool <albertpool@solcon.nl>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Boris Ostrovsky [Thu, 15 Nov 2012 18:41:50 +0000 (13:41 -0500)]
x86, microcode, AMD: Add support for family 16h processors
commit
36c46ca4f322a7bf89aad5462a3a1f61713edce7 upstream.
Add valid patch size for family 16h processors.
[ hpa: promoting to urgent/stable since it is hw enabling and trivial ]
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@amd.com>
Acked-by: Andreas Herrmann <herrmann.der.user@googlemail.com>
Link: http://lkml.kernel.org/r/1353004910-2204-1-git-send-email-boris.ostrovsky@amd.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Robert Richter [Mon, 3 Sep 2012 18:54:48 +0000 (20:54 +0200)]
x86-32: Fix invalid stack address while in softirq
commit
1022623842cb72ee4d0dbf02f6937f38c92c3f41 upstream.
In 32 bit the stack address provided by kernel_stack_pointer() may
point to an invalid range causing NULL pointer access or page faults
while in NMI (see trace below). This happens if called in softirq
context and if the stack is empty. The address at ®s->sp is then
out of range.
Fixing this by checking if regs and ®s->sp are in the same stack
context. Otherwise return the previous stack pointer stored in struct
thread_info. If that address is invalid too, return address of regs.
BUG: unable to handle kernel NULL pointer dereference at
0000000a
IP: [<
c1004237>] print_context_stack+0x6e/0x8d
*pde =
00000000
Oops: 0000 [#1] SMP
Modules linked in:
Pid: 4434, comm: perl Not tainted 3.6.0-rc3-oprofile-i386-standard-g4411a05 #4 Hewlett-Packard HP xw9400 Workstation/0A1Ch
EIP: 0060:[<
c1004237>] EFLAGS:
00010093 CPU: 0
EIP is at print_context_stack+0x6e/0x8d
EAX:
ffffe000 EBX:
0000000a ECX:
f4435f94 EDX:
0000000a
ESI:
f4435f94 EDI:
f4435f94 EBP:
f5409ec0 ESP:
f5409ea0
DS: 007b ES: 007b FS: 00d8 GS: 0033 SS: 0068
CR0:
8005003b CR2:
0000000a CR3:
34ac9000 CR4:
000007d0
DR0:
00000000 DR1:
00000000 DR2:
00000000 DR3:
00000000
DR6:
ffff0ff0 DR7:
00000400
Process perl (pid: 4434, ti=
f5408000 task=
f5637850 task.ti=
f4434000)
Stack:
000003e8 ffffe000 00001ffc f4e39b00 00000000 0000000a f4435f94 c155198c
f5409ef0 c1003723 c155198c f5409f04 00000000 f5409edc 00000000 00000000
f5409ee8 f4435f94 f5409fc4 00000001 f5409f1c c12dce1c 00000000 c155198c
Call Trace:
[<
c1003723>] dump_trace+0x7b/0xa1
[<
c12dce1c>] x86_backtrace+0x40/0x88
[<
c12db712>] ? oprofile_add_sample+0x56/0x84
[<
c12db731>] oprofile_add_sample+0x75/0x84
[<
c12ddb5b>] op_amd_check_ctrs+0x46/0x260
[<
c12dd40d>] profile_exceptions_notify+0x23/0x4c
[<
c1395034>] nmi_handle+0x31/0x4a
[<
c1029dc5>] ? ftrace_define_fields_irq_handler_entry+0x45/0x45
[<
c13950ed>] do_nmi+0xa0/0x2ff
[<
c1029dc5>] ? ftrace_define_fields_irq_handler_entry+0x45/0x45
[<
c13949e5>] nmi_stack_correct+0x28/0x2d
[<
c1029dc5>] ? ftrace_define_fields_irq_handler_entry+0x45/0x45
[<
c1003603>] ? do_softirq+0x4b/0x7f
<IRQ>
[<
c102a06f>] irq_exit+0x35/0x5b
[<
c1018f56>] smp_apic_timer_interrupt+0x6c/0x7a
[<
c1394746>] apic_timer_interrupt+0x2a/0x30
Code: 89 fe eb 08 31 c9 8b 45 0c ff 55 ec 83 c3 04 83 7d 10 00 74 0c 3b 5d 10 73 26 3b 5d e4 73 0c eb 1f 3b 5d f0 76 1a 3b 5d e8 73 15 <8b> 13 89 d0 89 55 e0 e8 ad 42 03 00 85 c0 8b 55 e0 75 a6 eb cc
EIP: [<
c1004237>] print_context_stack+0x6e/0x8d SS:ESP 0068:
f5409ea0
CR2:
000000000000000a
---[ end trace
62afee3481b00012 ]---
Kernel panic - not syncing: Fatal exception in interrupt
V2:
* add comments to kernel_stack_pointer()
* always return a valid stack address by falling back to the address
of regs
Reported-by: Yang Wei <wei.yang@windriver.com>
Signed-off-by: Robert Richter <robert.richter@amd.com>
Link: http://lkml.kernel.org/r/20120912135059.GZ8285@erda.amd.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Cc: Jun Zhang <jun.zhang@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
David S. Miller [Sat, 26 Nov 2011 21:54:17 +0000 (16:54 -0500)]
ifenslave: Fix unused variable warnings.
commit
450faacc621dbe0a4945ed8292afd45f4602d263 upstream.
Documentation/networking/ifenslave.c: In function ‘if_getconfig’:
Documentation/networking/ifenslave.c:508:14: warning: variable ‘mtu’ set but not used [-Wunused-but-set-variable]
Documentation/networking/ifenslave.c:508:6: warning: variable ‘metric’ set but not used [-Wunused-but-set-variable]
The purpose of this function is to simply print out the values
it probes, so...
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Danny Kukawka [Mon, 30 Jan 2012 22:00:17 +0000 (23:00 +0100)]
riva/fbdev: fix several -Wuninitialized
commit
c718a54649475cc397484f96e70f6d0fdd267165 upstream.
Fix several -Wuninitialized compiler warnings by changing the
order of getting modedb in riva_update_default_var() to set
first the fallback and then the prefered timing.
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Danny Kukawka [Fri, 2 Mar 2012 09:48:35 +0000 (10:48 +0100)]
drivers/block/DAC960: fix -Wuninitialized warning
commit
cecd353a02fb1405c8a72a324b26b5acf97e7411 upstream.
Set CommandMailbox with memset before use it. Fix for:
drivers/block/DAC960.c: In function ‘DAC960_V1_EnableMemoryMailboxInterface’:
arch/x86/include/asm/io.h:61:1: warning: ‘CommandMailbox.Bytes[12]’
may be used uninitialized in this function [-Wuninitialized]
drivers/block/DAC960.c:1175:30: note: ‘CommandMailbox.Bytes[12]’
was declared here
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Danny Kukawka [Fri, 2 Mar 2012 09:48:32 +0000 (10:48 +0100)]
drivers/block/DAC960: fix DAC960_V2_IOCTL_Opcode_T -Wenum-compare warning
commit
bca505f1097c725708ddc055cf8055e922b0904b upstream.
Fixed compiler warning:
comparison between ‘DAC960_V2_IOCTL_Opcode_T’ and ‘enum <anonymous>’
Renamed enum, added a new enum for SCSI_10.CommandOpcode in
DAC960_V2_ProcessCompletedCommand().
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Takashi Iwai [Tue, 14 Jun 2011 13:57:08 +0000 (15:57 +0200)]
ALSA: pcmcia - Use pcmcia_request_irq()
commit
08ef79490dad6b88010e94795cf9f89b018ed504 upstream.
The drivers don't require the exclusive irqs. Let's fix the deprecated
warnings.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Greg Kroah-Hartman [Mon, 26 Nov 2012 19:35:36 +0000 (11:35 -0800)]
Linux 3.0.53
Ram Pai [Thu, 22 Sep 2011 07:48:58 +0000 (15:48 +0800)]
Resource: fix wrong resource window calculation
commit
47ea91b4052d9e94b9dca5d7a3d947fbebd07ba9 upstream.
__find_resource() incorrectly returns a resource window which overlaps
an existing allocated window. This happens when the parent's
resource-window spans 0x00000000 to 0xffffffff and is entirely allocated
to all its children resource-windows.
__find_resource() looks for gaps in resource allocation among the
children resource windows. When it encounters the last child window it
blindly tries the range next to one allocated to the last child. Since
the last child's window ends at 0xffffffff the calculation overflows,
leading the algorithm to believe that any window in the range 0x0000000
to 0xfffffff is available for allocation. This leads to a conflicting
window allocation.
Michal Ludvig reported this issue seen on his platform. The following
patch fixes the problem and has been verified by Michal. I believe this
bug has been there for ages. It got exposed by git commit
2bbc6942273b
("PCI : ability to relocate assigned pci-resources")
Signed-off-by: Ram Pai <linuxram@us.ibm.com>
Tested-by: Michal Ludvig <mludvig@logix.net.nz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Herton Ronaldo Krzesinski <herton.krzesinski@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Yinghai Lu [Sat, 21 Jan 2012 10:08:17 +0000 (02:08 -0800)]
PCI : Calculate right add_size
commit
a4ac9fea016fc5c09227eb479bd35e34978323a4 upstream.
During debug of one SRIOV enabled hotplug device, we found found that
add_size is not passed properly.
The device has devices under two level bridges:
+-[0000:80]-+-00.0-[81-8f]--
| +-01.0-[90-9f]--
| +-02.0-[a0-af]----00.0-[a1-a3]--+-02.0-[a2]--+-00.0 Oracle Corporation Device
| | \-03.0-[a3]--+-00.0 Oracle Corporation Device
Which means later the parent bridge will not try to add a big enough range:
[ 557.455077] pci 0000:a0:00.0: BAR 14: assigned [mem 0xf9000000-0xf93fffff]
[ 557.461974] pci 0000:a0:00.0: BAR 15: assigned [mem 0xf6000000-0xf61fffff pref]
[ 557.469340] pci 0000:a1:02.0: BAR 14: assigned [mem 0xf9000000-0xf91fffff]
[ 557.476231] pci 0000:a1:02.0: BAR 15: assigned [mem 0xf6000000-0xf60fffff pref]
[ 557.483582] pci 0000:a1:03.0: BAR 14: assigned [mem 0xf9200000-0xf93fffff]
[ 557.490468] pci 0000:a1:03.0: BAR 15: assigned [mem 0xf6100000-0xf61fffff pref]
[ 557.497833] pci 0000:a1:03.0: BAR 14: can't assign mem (size 0x200000)
[ 557.504378] pci 0000:a1:03.0: failed to add optional resources res=[mem 0xf9200000-0xf93fffff]
[ 557.513026] pci 0000:a1:02.0: BAR 14: can't assign mem (size 0x200000)
[ 557.519578] pci 0000:a1:02.0: failed to add optional resources res=[mem 0xf9000000-0xf91fffff]
It turns out we did not calculate size1 properly.
static resource_size_t calculate_memsize(resource_size_t size,
resource_size_t min_size,
resource_size_t size1,
resource_size_t old_size,
resource_size_t align)
{
if (size < min_size)
size = min_size;
if (old_size == 1 )
old_size = 0;
if (size < old_size)
size = old_size;
size = ALIGN(size + size1, align);
return size;
}
We should not pass add_size with min_size in calculate_memsize since
that will make add_size not contribute final add_size.
So just pass add_size with size1 to calculate_memsize().
With this change, we should have chance to remove extra addon in
pci_reassign_resource.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Andrew Worsley <amworsley@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ram Pai [Mon, 25 Jul 2011 20:08:39 +0000 (13:08 -0700)]
PCI : ability to relocate assigned pci-resources
commit
2bbc6942273b5b3097bd265d82227bdd84b351b2 upstream.
Currently pci-bridges are allocated enough resources to satisfy their immediate
requirements. Any additional resource-requests fail if additional free space,
contiguous to the one already allocated, is not available. This behavior is not
reasonable since sufficient contiguous resources, that can satisfy the request,
are available at a different location.
This patch provides the ability to expand and relocate a allocated resource.
v2: Changelog: Fixed size calculation in pci_reassign_resource()
v3: Changelog : Split this patch. The resource.c changes are already
upstream. All the pci driver changes are in here.
Signed-off-by: Ram Pai <linuxram@us.ibm.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Andrew Worsley <amworsley@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dave Jones [Fri, 9 Nov 2012 00:09:27 +0000 (16:09 -0800)]
selinux: fix sel_netnode_insert() suspicious rcu dereference
commit
88a693b5c1287be4da937699cb82068ce9db0135 upstream.
===============================
[ INFO: suspicious RCU usage. ]
3.5.0-rc1+ #63 Not tainted
-------------------------------
security/selinux/netnode.c:178 suspicious rcu_dereference_check() usage!
other info that might help us debug this:
rcu_scheduler_active = 1, debug_locks = 0
1 lock held by trinity-child1/8750:
#0: (sel_netnode_lock){+.....}, at: [<
ffffffff812d8f8a>] sel_netnode_sid+0x16a/0x3e0
stack backtrace:
Pid: 8750, comm: trinity-child1 Not tainted 3.5.0-rc1+ #63
Call Trace:
[<
ffffffff810cec2d>] lockdep_rcu_suspicious+0xfd/0x130
[<
ffffffff812d91d1>] sel_netnode_sid+0x3b1/0x3e0
[<
ffffffff812d8e20>] ? sel_netnode_find+0x1a0/0x1a0
[<
ffffffff812d24a6>] selinux_socket_bind+0xf6/0x2c0
[<
ffffffff810cd1dd>] ? trace_hardirqs_off+0xd/0x10
[<
ffffffff810cdb55>] ? lock_release_holdtime.part.9+0x15/0x1a0
[<
ffffffff81093841>] ? lock_hrtimer_base+0x31/0x60
[<
ffffffff812c9536>] security_socket_bind+0x16/0x20
[<
ffffffff815550ca>] sys_bind+0x7a/0x100
[<
ffffffff816c03d5>] ? sysret_check+0x22/0x5d
[<
ffffffff810d392d>] ? trace_hardirqs_on_caller+0x10d/0x1a0
[<
ffffffff8133b09e>] ? trace_hardirqs_on_thunk+0x3a/0x3f
[<
ffffffff816c03a9>] system_call_fastpath+0x16/0x1b
This patch below does what Paul McKenney suggested in the previous thread.
Signed-off-by: Dave Jones <davej@redhat.com>
Reviewed-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Paul Moore <paul@paul-moore.com>
Cc: Eric Paris <eparis@parisplace.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Morris <james.l.morris@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jan Kara [Tue, 13 Nov 2012 17:25:38 +0000 (18:25 +0100)]
reiserfs: Protect reiserfs_quota_write() with write lock
commit
361d94a338a3fd0cee6a4ea32bbc427ba228e628 upstream.
Calls into reiserfs journalling code and reiserfs_get_block() need to
be protected with write lock. We remove write lock around calls to high
level quota code in the next patch so these paths would suddently become
unprotected.
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jan Kara [Tue, 13 Nov 2012 16:05:14 +0000 (17:05 +0100)]
reiserfs: Move quota calls out of write lock
commit
7af11686933726e99af22901d622f9e161404e6b upstream.
Calls into highlevel quota code cannot happen under the write lock. These
calls take dqio_mutex which ranks above write lock. So drop write lock
before calling back into quota code.
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jan Kara [Tue, 13 Nov 2012 15:34:17 +0000 (16:34 +0100)]
reiserfs: Protect reiserfs_quota_on() with write lock
commit
b9e06ef2e8706fe669b51f4364e3aeed58639eb2 upstream.
In reiserfs_quota_on() we do quite some work - for example unpacking
tail of a quota file. Thus we have to hold write lock until a moment
we call back into the quota code.
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jan Kara [Tue, 13 Nov 2012 13:55:52 +0000 (14:55 +0100)]
reiserfs: Fix lock ordering during remount
commit
3bb3e1fc47aca554e7e2cc4deeddc24750987ac2 upstream.
When remounting reiserfs dquot_suspend() or dquot_resume() can be called.
These functions take dqonoff_mutex which ranks above write lock so we have
to drop it before calling into quota code.
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Bryan Schumaker [Tue, 30 Oct 2012 20:06:35 +0000 (16:06 -0400)]
NFS: Wait for session recovery to finish before returning
commit
399f11c3d872bd748e1575574de265a6304c7c43 upstream.
Currently, we will schedule session recovery and then return to the
caller of nfs4_handle_exception. This works for most cases, but causes
a hang on the following test case:
Client Server
------ ------
Open file over NFS v4.1
Write to file
Expire client
Try to lock file
The server will return NFS4ERR_BADSESSION, prompting the client to
schedule recovery. However, the client will continue placing lock
attempts and the open recovery never seems to be scheduled. The
simplest solution is to wait for session recovery to run before retrying
the lock.
Signed-off-by: Bryan Schumaker <bjschuma@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Daniel Vetter [Mon, 22 Oct 2012 10:55:55 +0000 (12:55 +0200)]
drm/i915: fix overlay on i830M
commit
a9193983f4f292a82a00c72971c17ec0ee8c6c15 upstream.
The overlay on the i830M has a peculiar failure mode: It works the
first time around after boot-up, but consistenly hangs the second time
it's used.
Chris Wilson has dug out a nice errata:
"1.5.12 Clock Gating Disable for Display Register
Address Offset: 06200h–06203h
"Bit 3
Ovrunit Clock Gating Disable.
0 = Clock gating controlled by unit enabling logic
1 = Disable clock gating function
DevALM Errata ALM049: Overlay Clock Gating Must be Disabled: Overlay
& L2 Cache clock gating must be disabled in order to prevent device
hangs when turning off overlay.SW must turn off Ovrunit clock gating
(6200h) and L2 Cache clock gating (C8h)."
Now I've nowhere found that 0xc8 register and hence couldn't apply the
l2 cache workaround. But I've remembered that part of the magic that
the OVERLAY_ON/OFF commands are supposed to do is to rearrange cache
allocations so that the overlay scaler has some scratch space.
And while pondering how that could explain the hang the 2nd time we
enable the overlay, I've remembered that the old ums overlay code did
_not_ issue the OVERLAY_OFF cmd.
And indeed, disabling the OFF cmd results in the overlay working
flawlessly, so I guess we can workaround the lack of the above
workaround by simply never disabling the overlay engine once it's
enabled.
Note that we have the first part of the above w/a already implemented
in i830_init_clock_gating - leave that as-is to avoid surprises.
v2: Add a comment in the code.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=47827
Tested-by: Rhys <rhyspuk@gmail.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
[bwh: Backported to 3.2:
- Adjust context
- s/intel_ring_emit(ring, /OUT_RING(/]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mirko Lindner [Tue, 3 Jul 2012 23:38:46 +0000 (23:38 +0000)]
sky2: Fix for interrupt handler
commit
d663d181b9e92d80c2455e460e932d34e7a2a7ae upstream.
Re-enable interrupts if it is not our interrupt
Signed-off-by: Mirko Lindner <mlindner@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: Jonathan Nieder <jrnieder@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tim Sally [Thu, 12 Jul 2012 23:10:24 +0000 (19:10 -0400)]
eCryptfs: check for eCryptfs cipher support at mount
commit
5f5b331d5c21228a6519dcb793fc1629646c51a6 upstream.
The issue occurs when eCryptfs is mounted with a cipher supported by
the crypto subsystem but not by eCryptfs. The mount succeeds and an
error does not occur until a write. This change checks for eCryptfs
cipher support at mount time.
Resolves Launchpad issue #338914, reported by Tyler Hicks in 03/2009.
https://bugs.launchpad.net/ecryptfs/+bug/338914
Signed-off-by: Tim Sally <tsally@atomicpeace.com>
Signed-off-by: Tyler Hicks <tyhicks@canonical.com>
Cc: Herton Ronaldo Krzesinski <herton.krzesinski@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tyler Hicks [Mon, 11 Jun 2012 22:42:32 +0000 (15:42 -0700)]
eCryptfs: Copy up POSIX ACL and read-only flags from lower mount
commit
069ddcda37b2cf5bb4b6031a944c0e9359213262 upstream.
When the eCryptfs mount options do not include '-o acl', but the lower
filesystem's mount options do include 'acl', the MS_POSIXACL flag is not
flipped on in the eCryptfs super block flags. This flag is what the VFS
checks in do_last() when deciding if the current umask should be applied
to a newly created inode's mode or not. When a default POSIX ACL mask is
set on a directory, the current umask is incorrectly applied to new
inodes created in the directory. This patch ignores the MS_POSIXACL flag
passed into ecryptfs_mount() and sets the flag on the eCryptfs super
block depending on the flag's presence on the lower super block.
Additionally, it is incorrect to allow a writeable eCryptfs mount on top
of a read-only lower mount. This missing check did not allow writes to
the read-only lower mount because permissions checks are still performed
on the lower filesystem's objects but it is best to simply not allow a
rw mount on top of ro mount. However, a ro eCryptfs mount on top of a rw
mount is valid and still allowed.
https://launchpad.net/bugs/1009207
Signed-off-by: Tyler Hicks <tyhicks@canonical.com>
Reported-by: Stefan Beller <stefanbeller@googlemail.com>
Cc: John Johansen <john.johansen@canonical.com>
Cc: Herton Ronaldo Krzesinski <herton.krzesinski@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jan Safrata [Tue, 22 May 2012 12:04:50 +0000 (14:04 +0200)]
usb: use usb_serial_put in usb_serial_probe errors
commit
0658a3366db7e27fa32c12e886230bb58c414c92 upstream.
The use of kfree(serial) in error cases of usb_serial_probe
was invalid - usb_serial structure allocated in create_serial()
gets reference of usb_device that needs to be put, so we need
to use usb_serial_put() instead of simple kfree().
Signed-off-by: Jan Safrata <jan.nikitenko@gmail.com>
Acked-by: Johan Hovold <jhovold@gmail.com>
Cc: Richard Retanubun <richardretanubun@ruggedcom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ulrich Weber [Thu, 25 Oct 2012 05:34:45 +0000 (05:34 +0000)]
netfilter: nf_nat: don't check for port change on ICMP tuples
commit
38fe36a248ec3228f8e6507955d7ceb0432d2000 upstream.
ICMP tuples have id in src and type/code in dst.
So comparing src.u.all with dst.u.all will always fail here
and ip_xfrm_me_harder() is called for every ICMP packet,
even if there was no NAT.
Signed-off-by: Ulrich Weber <ulrich.weber@sophos.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jozsef Kadlecsik [Fri, 31 Aug 2012 09:55:53 +0000 (09:55 +0000)]
netfilter: Mark SYN/ACK packets as invalid from original direction
commit
64f509ce71b08d037998e93dd51180c19b2f464c upstream.
Clients should not send such packets. By accepting them, we open
up a hole by wich ephemeral ports can be discovered in an off-path
attack.
See: "Reflection scan: an Off-Path Attack on TCP" by Jan Wrobel,
http://arxiv.org/abs/1201.2074
Signed-off-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jozsef Kadlecsik [Fri, 31 Aug 2012 09:55:54 +0000 (09:55 +0000)]
netfilter: Validate the sequence number of dataless ACK packets as well
commit
4a70bbfaef0361d27272629d1a250a937edcafe4 upstream.
We spare nothing by not validating the sequence number of dataless
ACK packets and enabling it makes harder off-path attacks.
See: "Reflection scan: an Off-Path Attack on TCP" by Jan Wrobel,
http://arxiv.org/abs/1201.2074
Signed-off-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jean Delvare [Tue, 2 Oct 2012 14:42:36 +0000 (16:42 +0200)]
kbuild: Fix gcc -x syntax
commit
b1e0d8b70fa31821ebca3965f2ef8619d7c5e316 upstream.
The correct syntax for gcc -x is "gcc -x assembler", not
"gcc -xassembler". Even though the latter happens to work, the former
is what is documented in the manual page and thus what gcc wrappers
such as icecream do expect.
This isn't a cosmetic change. The missing space prevents icecream from
recognizing compilation tasks it can't handle, leading to silent kernel
miscompilations.
Besides me, credits go to Michael Matz and Dirk Mueller for
investigating the miscompilation issue and tracking it down to this
incorrect -x parameter syntax.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Acked-by: Ingo Molnar <mingo@kernel.org>
Cc: Bernhard Walle <bernhard@bwalle.de>
Cc: Michal Marek <mmarek@suse.cz>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Michal Marek <mmarek@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Michal Schmidt [Sun, 9 Sep 2012 13:55:26 +0000 (13:55 +0000)]
r8169: use unlimited DMA burst for TX
commit
aee77e4accbeb2c86b1d294cd84fec4a12dde3bd upstream.
The r8169 driver currently limits the DMA burst for TX to 1024 bytes. I have
a box where this prevents the interface from using the gigabit line to its full
potential. This patch solves the problem by setting TX_DMA_BURST to unlimited.
The box has an ASRock B75M motherboard with on-board RTL8168evl/8111evl
(XID
0c900880). TSO is enabled.
I used netperf (TCP_STREAM test) to measure the dependency of TX throughput
on MTU. I did it for three different values of TX_DMA_BURST ('5'=512, '6'=1024,
'7'=unlimited). This chart shows the results:
http://michich.fedorapeople.org/r8169/r8169-effects-of-TX_DMA_BURST.png
Interesting points:
- With the current DMA burst limit (1024):
- at the default MTU=1500 I get only 842 Mbit/s.
- when going from small MTU, the performance rises monotonically with
increasing MTU only up to a peak at MTU=1076 (908 MBit/s). Then there's
a sudden drop to 762 MBit/s from which the throughput rises monotonically
again with further MTU increases.
- With a smaller DMA burst limit (512):
- there's a similar peak at MTU=1076 and another one at MTU=564.
- With unlimited DMA burst:
- at the default MTU=1500 I get nice 940 Mbit/s.
- the throughput rises monotonically with increasing MTU with no strange
peaks.
Notice that the peaks occur at MTU sizes that are multiples of the DMA burst
limit plus 52. Why 52? Because:
20 (IP header) + 20 (TCP header) + 12 (TCP options) = 52
The Realtek-provided r8168 driver (v8.032.00) uses unlimited TX DMA burst too,
except for CFG_METHOD_1 where the TX DMA burst is set to 512 bytes.
CFG_METHOD_1 appears to be the oldest MAC version of "RTL8168B/8111B",
i.e. RTL_GIGA_MAC_VER_11 in r8169. Not sure if this MAC version really needs
the smaller burst limit, or if any other versions have similar requirements.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tom Herbert [Fri, 16 Nov 2012 09:04:15 +0000 (09:04 +0000)]
net-rps: Fix brokeness causing OOO packets
[ Upstream commit
baefa31db2f2b13a05d1b81bdf2d20d487f58b0a ]
In commit
c445477d74ab3779 which adds aRFS to the kernel, the CPU
selected for RFS is not set correctly when CPU is changing.
This is causing OOO packets and probably other issues.
Signed-off-by: Tom Herbert <therbert@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Acked-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jiri Pirko [Wed, 14 Nov 2012 02:51:04 +0000 (02:51 +0000)]
net: correct check in dev_addr_del()
[ Upstream commit
a652208e0b52c190e57f2a075ffb5e897fe31c3b ]
Check (ha->addr == dev->dev_addr) is always true because dev_addr_init()
sets this. Correct the check to behave properly on addr removal.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hannes Frederic Sowa [Sat, 10 Nov 2012 19:52:34 +0000 (19:52 +0000)]
ipv6: setsockopt(IPIPPROTO_IPV6, IPV6_MINHOPCOUNT) forgot to set return value
[ Upstream commit
d4596bad2a713fcd0def492b1960e6d899d5baa8 ]
Cc: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Xi Wang [Sun, 11 Nov 2012 11:20:01 +0000 (11:20 +0000)]
ipv4: avoid undefined behavior in do_ip_setsockopt()
[ Upstream commit
0c9f79be295c99ac7e4b569ca493d75fdcc19e4e ]
(1<<optname) is undefined behavior in C with a negative optname or
optname larger than 31. In those cases the result of the shift is
not necessarily zero (e.g., on x86).
This patch simplifies the code with a switch statement on optname.
It also allows the compiler to generate better code (e.g., using a
64-bit mask).
Signed-off-by: Xi Wang <xi.wang@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Andreas Schwab [Sat, 17 Nov 2012 21:27:04 +0000 (22:27 +0100)]
m68k: fix sigset_t accessor functions
commit
34fa78b59c52d1db3513db4c1a999db26b2e9ac2 upstream.
The sigaddset/sigdelset/sigismember functions that are implemented with
bitfield insn cannot allow the sigset argument to be placed in a data
register since the sigset is wider than 32 bits. Remove the "d"
constraint from the asm statements.
The effect of the bug is that sending RT signals does not work, the signal
number is truncated modulo 32.
Signed-off-by: Andreas Schwab <schwab@linux-m68k.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johannes Berg [Mon, 12 Nov 2012 09:51:34 +0000 (10:51 +0100)]
wireless: allow 40 MHz on world roaming channels 12/13
commit
43c771a1963ab461a2f194e3c97fded1d5fe262f upstream.
When in world roaming mode, allow 40 MHz to be used
on channels 12 and 13 so that an AP that is, e.g.,
using HT40+ on channel 9 (in the UK) can be used.
Reported-by: Eddie Chapman <eddie@ehuk.net>
Tested-by: Eddie Chapman <eddie@ehuk.net>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dan Williams [Thu, 8 Nov 2012 17:56:53 +0000 (11:56 -0600)]
USB: option: add Alcatel X220/X500D USB IDs
commit
c0bc3098871dd9b964f6b45ec1e4d70d87811744 upstream.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dan Williams [Thu, 8 Nov 2012 17:56:42 +0000 (11:56 -0600)]
USB: option: add Novatel E362 and Dell Wireless 5800 USB IDs
commit
fcb21645f1bd86d2be29baf48aa1b298de52ccc7 upstream.
The Dell 5800 appears to be a simple rebrand of the Novatel E362.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>