scsi: hpsa: add 'ctlr_num' sysfs attribute

Add a sysfs attribute 'ctlr_num' holding the current HPSA controller
number. This is required to construct compability 'cciss' links.

[mkp: fixed typo]

Signed-off-by: Hannes Reinecke <hare@suse.com>
Acked-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: hpsa: use correct DID_NO_CONNECT hostbyte

NOT_READY is a sense key, not a legit scsi hostbyte value. Use
DID_NO_CONNECT instead.

Signed-off-by: Hannes Reinecke <hare@suse.com>
Acked-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: srp_transport: Move queuecommand() wait code to SCSI core

Additionally, rename srp_wait_for_queuecommand() into
scsi_wait_for_queuecommand() and add a comment about the queuecommand()
call from scsi_send_eh_cmnd().

Note: this patch changes scsi_internal_device_block from a function that
did not sleep into a function that may sleep. This is fine for all
callers of this function:

* scsi_internal_device_block() is called from the mpt3sas device while
  that driver holds the ioc->dm_cmds.mutex. This means that the mpt3sas
  driver calls this function from thread context.
* scsi_target_block() is called by __iscsi_block_session() from
  kernel thread context and with IRQs enabled.
* The SRP transport code also calls scsi_target_block() from kernel
  thread context while sleeping is allowed.
* The snic driver also calls scsi_target_block() from a context from
  which sleeping is allowed. The scsi_target_block() call namely occurs
  immediately after a scsi_flush_work() call.

[mkp: s/shost/sdev/]

Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Cc: James Bottomley <jejb@linux.vnet.ibm.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Doug Ledford <dledford@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: libfc: Remove an unneeded condition

We verified that resp_code is FC_SPP_RESP_ACK earlier so we don't need
to check again here.

Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Johannes Thumshirn <jth@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: ufs: Add missing UFS_MASK macro definition

Reported-by: Venkatraman S <svenkatr@ti.com>
Reviewed-by: Vinayak Holikatti <vinholikatti@gmail.com>
Signed-off-by: Santosh Y <santoshsy@gmail.com>
Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: hisi_sas: add PHY set linkrate support for v1 and v2 hw

Add the function to set PHY min and max linkrate through
sysfs interface.

Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: hisi_sas: use atomic64_t for hisi_sas_device.running_req

Sometimes the value of hisi_sas_device.running_req
would go negative unless we have the check for
running_req >= 0 before trying to decrement.

This is because using running_req is not thread-safe.

As such, the value for running_req may be actually incorrect,
so use atomic64_t instead.

Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Xiang Chen <chenxiang66@hisilicon.com>
Reviewed-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: hisi_sas: check SATA FIS when directly attaching SATA device

Check ERR bit of status to decide whether there is something wrong with
initial register-D2H FIS. If error exists, PHY reset the channel to
restart OOB.

Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: hisi_sas: modify some values in get_ata_protocol()

Modify and add some SATA commands according to SATA protocol.

Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: hisi_sas: delete repeated configuration in free_device_v2_hw()

Delete repeated configuration items for hisi_sas_device() when
we free a device. These items are now only set in
hisi_sas_dev_gone().

Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: hisi_sas: modify return value of hisi_sas_query_task()

sas_scsi_find_task() only deals with return value
TMF_RESP_FUNC_FAILED/TMF_RESP_FUNC_SUCC/TMF_RESP_FUNC_COMPLETE of
query task. So for LLDD errors just return TMF_RESP_FUNC_FAILED.

Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: hisi_sas: replace WARN_ON() with dev_warn() for internal abort

Replace WARN_ON() with dev_warn() print when internal abort fails.

Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: hisi_sas: fix port form bug in hisi_sas_port_notify_formed()

When we form a wideport, we should use hardware PHY port_id instead
of sas_phy->id.

Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: hisi_sas: only process broadcast change in phy_bcast_v2_hw()

There are many BROADCAST primitives generated by the host.
We are only interested in BROADCAST (CHANGE) primitives currently,
so only process this.

Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: hisi_sas: alloc queue id of slot according to device id

Currently slots are allocated from queues in a round-robin fashion.
This causes a problem for internal commands in device mode. For this
mode, we should ensure that the internal abort command is the last
command seen in the host for that device. We can only ensure this when
we place the internal abort command after the preceding commands for
device that in the same queue, as there is no order in which the host
will select a queue to execute the next command.

This queue restriction makes supporting scsi mq more tricky in
the future, but should not be a blocker.

Note: Even though v1 hw does not support internal abort, the
      allocation method is chosen to be the same for consistency.

Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: hisi_sas: add v2 hw support for ECC and AXI bus fatal error

For ECC 1bit error, logic can recover it, so we only print
a warning.
For ECC multi-bit and AXI bus fatal error, we panic.

Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: pmcraid: Add missing resource releases

Most error branches following the call to pmcraid_get_free_cmd contain a
call to pmcraid_return_cmd. This patch add these calls where they are
missing.

Moreover, most error branches following the call to class_create contain
a call to class_destroy. This patch add these calls where they are
missing.

This issue was found with Hector.

Signed-off-by: Quentin Lambert <lambert.quentin@gmail.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: ufs: introduce UFSHCD_QUIRK_PRDT_BYTE_GRAN quirk

Some UFS host controllers may think granularities of PRDT length and
offset as bytes, not double words.

Signed-off-by: Kiwoong Kim <kwmad.kim@samsung.com>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: ufs: qcom: Properly clear hba priv on failure

ufs_qcom_init() sets the hba priv data before attempting to acquire the
phy handle, so make sure to clear this in the case of an error. Failing
to do this will make ufs_qcom_setup_clocks() operate on the uninitalized
host object.

Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: bfa: turn bfa_mem_{kva,dma}_setup into inline functions

These two macros cause lots of warnings with gcc-7:

drivers/scsi/bfa/bfa_svc.c: In function 'bfa_fcxp_meminfo':
drivers/scsi/bfa/bfa_svc.c:521:103: error: '*' in boolean context, suggest '&&' instead [-Werror=int-in-bool-context]

Using inline functions makes them much more readable and avoids the
warnings.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Acked by: Anil Gurumurthy <anil.gurumurthy@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: mptfusion: Fix printk continuations

Fix the printk continuations when running the mptfusion driver.
This patch brings the capabilities into one single syslog line again:
   mptbase: ioc1: Initiating bringup
   ioc1: LSI53C1030 B2: Capabilities={Initiator,Target}
   scsi host3: ioc1: LSI53C1030 B2, FwRev=01032341h, Ports=1, MaxQ=255, IRQ=67

Tested on a parisc C8000 machine.

Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: aacraid: switch to pci_alloc_irq_vectors

Use pci_alloc_irq_vectors and drop the hand-crafted interrupt affinity
routines.

Signed-off-by: Hannes Reinecke <hare@suse.com>
Cc: Adaptec OEM Raid Solutions <aacraid@microsemi.com>
Reviewed-by: Raghava Aditya Renukunta <raghavaaditya.renukunta@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: fc: move FC transport's bsg code to bsg-lib

Now that all conversions are done, move the FibreChannel bsg code over
to the bsg library.

This patch is derived from work done by Mike Christie in 2011 [1] but
only the iscsi parts got merged back then.

[1] http://marc.info/?l=linux-scsi&m=131149780921009&w=2

Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

block: add bsg_job_put() and bsg_job_get()

Add bsg_job_put() and bsg_job_get() so don't need to export
bsg_destroy_job() any more.

Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: fc: use bsg_job_done

fc_bsg_jobdone() and bsg_job_done() are 1:1 copies now so use the
bsg-lib one instead of the FC private implementation.

Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Acked-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: fc: use bsg_softirq_done

bsg_softirq_done() and fc_bsg_softirq_done() are copies of each other, so
ditch the fc specific one.

Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: fc: Use bsg_destroy_job

fc_destroy_bsgjob() and bsg_destroy_job() are now 1:1 copies, so use the
latter. As bsg_destroy_job() comes from bsg-lib we need to select it in
Kconfig once CONFOG_SCSI_FC_ATTRS is active.

Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: change FC drivers to use 'struct bsg_job'

Change FC drivers to use 'struct bsg_job' from bsg-lib.h instead of
'struct fc_bsg_job' from scsi_transport_fc.h and remove 'struct
fc_bsg_job'.

Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Acked-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

block: add reference counting for struct bsg_job

Add reference counting to 'struct bsg_job' so we can implement a reuqest
timeout handler for bsg_jobs, which is needed for Fibre Channel.

Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: fc: implement kref backed reference counting

Implement kref backed reference counting instead of rolling our own. This
elimnates the need of the following fields in 'struct fc_bsg_job':
* ref_cnt
* state_flags
* job_lock
bringing us close to unification of 'struct fc_bsg_job' and 'struct bsg_job'.

Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: libfc: don't set FC_RQST_STATE_DONE before calling fc_bsg_jobdone()

Don't set FC_RQST_STATE_DONE before calling fc_bsg_jobdone() as
fc_bsg_jobdone() calls blk_complete_requeust() which raises a soft-IRQ
that ends up in fc_bsg_sofirq_done() and fc_bsg_softirq_done() sets the
FC_RQST_STATE_DONE flag.

Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: fc: provide fc_bsg_to_rport() helper

Provide fc_bsg_to_rport() helper that will become handy when we're
moving from struct fc_bsg_job to a plain struct bsg_job. Also move all
LLDDs to use the new helper.

Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Acked-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: fc: provide fc_bsg_to_shost() helper

Provide fc_bsg_to_shost() helper that will become handy when we're
moving from struct fc_bsg_job to a plain struct bsg_job. Also use this
little helper in the LLDDs.

Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Acked-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: fc: Export fc_bsg_jobdone and use it in FC drivers

Export fc_bsg_jobdone so drivers can use it directly instead of doing
the round-trip via struct fc_bsg_job::job_done() and use it in the
LLDDs.  That way we can also unify the interfaces of fc_bsg_jobdone and
bsg_job_done.

As we've converted all LLDDs over to use fc_bsg_jobdone() directly, we
can remove the function pointer from struct fc_bsg_job as well.

Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: don't use fc_bsg_job::request and fc_bsg_job::reply directly

Don't use fc_bsg_job::request and fc_bsg_job::reply directly, but use
helper variables bsg_request and bsg_reply. This will be helpful when
transitioning to bsg-lib.

Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: Get rid of struct fc_bsg_buffer

struct fc_bsg_buffer is just a clone of struct bsg_buffer from bsg-lib,
so use this one instead.

Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: mvsas: fix command_active typo

gcc-7 notices that the condition in mvs_94xx_command_active looks
suspicious:

drivers/scsi/mvsas/mv_94xx.c: In function 'mvs_94xx_command_active':
drivers/scsi/mvsas/mv_94xx.c:671:15: error: '<<' in boolean context, did you mean '<' ? [-Werror=int-in-bool-context]

This was introduced when the mv_printk() statement got added, and leads
to the condition being ignored. This is probably harmless.

Changing '&&' to '&' makes the code look reasonable, as we check the
command bit before setting and printing it.

Fixes: a4632aae8b66 ("[SCSI] mvsas: Add new macros and functions")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: dmx3191d: use module_pci_driver

Use module_pci_driver() helper to simplify the code.

Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Acked-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: fnic: Correcting rport check location in fnic_queuecommand_lck

Signed-off-by: Satish Kharat <satishkh@cisco.com>
Signed-off-by: Sesidhar Baddela <sebaddel@cisco.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: ufs: introduce a new ufshcd_statea UFSHCD_STATE_EH_SCHEDULED

Add a new ufshcd_state, indicats that an err handler may get to run
immediately. Use UFSHCD_STATE_ERROR here looks not literaly correct.

Signed-off-by: Zang Leigang <zangleigang@hisilicon.com>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

MAINTAINERS: Updating maintainers list for Cisco FNI and SNIC drivers

Signed-off-by: Satish Kharat <satishkh@cisco.com>
Signed-off-by: Sesidhar Baddela <sebaddel@cisco.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: hpsa: correct logical resets

- driver was not calling done in some cases which causes the volume to
  be offlined.
- avoid doing rescan during a reset.

Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: megaraid-sas: request irqs later

It is not good when an irq arrives before driver structures are
allocated.

Signed-off-by: Tomas Henzl <thenzl@redhat.com>
Acked-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: hpsa: free irq on q indexed by h->intr_mode and not i

Use correct index on q, use h->intr_mode instead of i. Issue detected
using static analysis with cppcheck

Fixes: bc2bb1543e62a5d0 ("scsi: hpsa: use pci_alloc_irq_vectors and automatic irq affinity")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: isci: fix typo in deg_dbg message

Trivial fix to typo "repsonse" to "response" in dev_dbg message.

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: isci: fix spelling mistakes in dev_warn messages

Trivial fix to spelling mistake "suspeneded" to "suspended" in dev_warn
messages.

[mkp: corrected description. Patch is against the isci driver, not iscsi]

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: megaraid_sas: add in missing white spaces in error messages text

A couple of dev_printk messages spans two lines and the literal string
is missing a white space between words. Add the white space.

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: scsi_transport_fc: Hold queue lock while calling blk_run_queue_async()

It is required to hold the queue lock when calling blk_run_queue_async()
to avoid that a race between blk_run_queue_async() and
blk_cleanup_queue() is triggered. Additionally, remove the get_device()
and put_device() calls from fc_bsg_goose_queue. It is namely the
responsibility of the caller of fc_bsg_goose_queue() to ensure that the
bsg queue does not disappear while fc_bsg_goose_queue() is in progress.

Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Hannes Reinecke <hare@suse.de>
Cc: James Smart <james.smart@avagotech.com>
Reviewed-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: g_NCR5380: Fix release_region in error handling

When a SW-configurable card is specified but not found, the driver
releases wrong region, causing the following message in kernel log:
Trying to free nonexistent resource <0000000000000000-000000000000000f>

Fix it by assigning base earlier.

Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Fixes: a8cfbcaec0c1 ("scsi: g_NCR5380: Stop using scsi_module.c")
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: ufs: introduce hibern8_notify callback

Some UFS host controller may need to configure some things around
hibern8 enter/exit

Signed-off-by: Kiwoong Kim <kwmad.kim@samsung.com>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: ufs: introduce setup_task_mgmt

Some UFS host controller may need to configure some things before any
task management request is issued

Signed-off-by: Kiwoong Kim <kwmad.kim@samsung.com>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: ufs: introduce setup_xfer_req callback

Some UFS host controller may need to configure some things before any
transfer request is issued.

Signed-off-by: Kiwoong Kim <kwmad.kim@samsung.com>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: hpsa: use pci_alloc_irq_vectors and automatic irq affinity

This patch converts over hpsa to use the pci_alloc_irq_vectors including
the PCI_IRQ_AFFINITY flag that automatically assigns spread out irq
affinity to the I/O queues.

It also cleans up the per-ctrl interrupt state due to the use of the
pci_irq_vector and pci_free_irq_vectors helpers that don't need to know
the exact irq type.  Additionally it changes a little oddity in the
existing code that was using different array indixes into the per-vector
arrays depending on whether a controller is using a single INTx or
single MSI irq.

[mkp: fixed typo]

Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Don Brace <don.brace@microsemi.com>
Tested-by: Don Brace <don.brace@microsemi.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: ufs: Use the resource-managed function to add devfreq device

This patch uses the resource-managed to add the devfreq device.  This
function will make it easy to handle the devfreq device.

- struct devfreq *devm_devfreq_add_device(struct device *dev,
  struct devfreq_dev_profile *profile,
  const char *governor_name,
  void *data);
Cc: Vinayak Holikatti <vinholikatti@gmail.com>
Cc: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: linux-scsi@vger.kernel.org
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: fix spelling mistake in error message

Trivial fix to spelling mistake "operatio" to "operation" in critical
error message

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: mpt3sas: fix some spelling mistakes in message and comments

Trivial fixes, minor spelling mistakes in comments and in a KERN_INFO
message.

[mkp: fixed spelling mistake in patch description]

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: ufs: qcom: Don't free resource-managed kmalloc element

Host is allocated by managed kmalloc (devm_kmalloc). The
memory allocated with this function is automatically
freed on driver detach.
So, no need to make an exclusive free call over it.

Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: ufs: qcom: Add phy_exit call in hcd exit path

Do a phy_exit() over the ufs phy in the ufs qcom exit path
to de-initialize the phy.

Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

phy: qcom-ufs: Remove common layer phy exit callback

The common layer phy exit callback ufs_qcom_phy_exit()
calls phy_power_off() that has no meaning when phy_power_off()
callback is already registered with the phy provider and
the consumer makes use of the same.
Instead, add a no-op specific phy_exit() callback for now
to add the exit sequence at a later point.

Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: ufs-qcom: phy/hcd: Refactoring phy clock handling

Add phy clock enable code to phy_power_on/off callbacks, and
remove explicit calls to enable these phy clocks from the
ufs-qcom hcd driver.

Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

phy: qcom-ufs-qmp-xx: Move clock and regulator init out of phy init

The phy init is meant to do phy initialization rather than
just getting the clock and regulator. Move these clock and
regulator get to probe(), to make room for actual phy
initialization sequence.

Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

phy: qcom-ufs: Remove unnecessary function declarations

Move the functions' definitions to remove unnecessary
declarations.

Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

phy: qcom-ufs-qmp-xx: Discard remove callback for drivers.

remove() callback does a phy_power_off() only over the phy,
and nothing else now.
The phy_power_off() over the generic phy is called from the phy
consumer, and phy provider driver should not explicitly need to
call any phy ops.
So discard the remove callback for qcom-ufs phy platform drivers.

Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

phy: qcom-ufs: Skip obtaining rx/tx_iface_clk for msm8996 based phy

The tx_iface_clk and rx_iface_clk no longer exist with UFS Phy
present on msm8996. So skip obtaining these clocks using
compatible match.

Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

phy: qcom-ufs-14nm: Add new compatible for msm8996 based phy

Add a new compatible string for 14nm ufs phy present on msm8996
chipset. This phy is bit different from the legacy 14nm ufs phy
in terms of the clocks that are needed to be handled in the driver.

Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

phy: qcom-ufs: Cleanup clock and regulator initialization

Different menthods pass around generic phy pointer to
extract device pointer. Instead, pass the device pointer
directly between function calls.

Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

phy: qcom-ufs: Use devm sibling of kstrdup for regulator names

This helps us in avoiding any requirement for kfree() operation
to be called exclusively over the allocated string pointer.

Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

phy: qcom-ufs: Remove unnecessary BUG_ON

BUG_ON() are not preferred in the driver, plus the variable
on which BUG_ON is asserted is already checked in the code
before passing.

Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: megaraid_sas: driver version upgrade

Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: megaraid_sas: Do not set MPI2_TYPE_CUDA for JBOD FP path for FW which does not support JBOD sequence map

CC: stable@vger.kernel.org
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

MAINTAINERS: Update megaraid maintainers list

Update MEGARAID drivers maintainers list.

Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: megaraid_sas: Send SYNCHRONIZE_CACHE for VD to firmware

Until now the megaraid_sas driver has reported successful completion on
SYNCHRONIZE_CACHE commands without sending them down to the controller.
The controller firmware has been responsible for taking care of flushing
disk caches for all drives that belong to a Virtual Disk at the time of
system reboot/shutdown.

There may have been a reason to avoid sending SYNCHRONIZE_CACHE to a VD
in the past but that no longer appears to be valid.

Older versions of MegaRaid firmware (Gen2 and Gen2.5) set the WCE bit
for Virtual Disks but the firmware does not report correct completion
status for a SYNCHRONIZE_CACHE command. As a result, we must use another
method to identify whether it is safe to send the command to the
controller. We use the canHandleSyncCache firmware flag in the scratch
pad register at offset 0xB4.

New SYNCHRONIZE_CACHE behavior:

IF 'JBOD'

Driver sends SYNCHRONIZE_CACHE command to the firmware
Firmware sends SYNCHRONIZE_CACHE to drive
Firmware obtains status from drive and returns same status back to driver

ELSEIF 'VirtualDisk'

IF firmware supports new API bit called canHandleSyncCache
Driver sends SYNCHRONIZE_CACHE command to the firmware
Firmware does not send SYNCHRONIZE_CACHE to drives
Firmware returns SUCCESS
ELSE
Driver does not send SYNCHRONIZE_CACHE command to the firmware
Driver return SUCCESS for that command
ENDIF
ENDIF

[mkp: edited patch description]

Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: smartpqi: switch to pci_alloc_irq_vectors

Which cleans up a lot of the MSI-X handling, and allows us to use the
PCI IRQ layer provided vector mapping, which we can then expose to
blk-mq.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Acked-by: Don Brace <don.brace@microsemi.com>
Tested-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: allow LLDDs to expose the queue mapping to blk-mq

Just hand through the blk-mq map_queues method in the host template.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

blk-mq: export blk_mq_map_queues

This will allow SCSI to have a single blk_mq_ops structure that either
lets the LLDD map the queues to PCIe MSIx vectors or use the default.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: ufs: change device rails hpm mode ramp up sequence

When we are resuming the UFS device rails in HPM mode, we are first
powering on the VCC rail while VCCQ and VCCQ2 rails still being in LPM
mode. Some UFS devices may take VCC on event as hint that host wants UFS
device to be resumed and may start drawing more power from the
VCCQ/VCCQ2 rails (while they are still in LPM mode) causing voltage drop
on these rails. This change fixes this issue by bringing VCCQ & VCCQ2
rails out of LPM before powering on VCC rail.

Reviewed-by: Venkat Gopalakrishnan <venkatg@codeaurora.org>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: ufs: suspend clock scaling at the start of suspend

Currently clock scaling is suspended only after the host and device are
put in low power mode but we should avoid clock scaling running after
UFS link is put in low power mode (hibern8). This change suspends clock
scaling before putting host/device in low power mode.

Reviewed-by: Sahitya Tummala <stummala@codeaurora.org>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: ufshcd: release resources if probe fails

If ufshcd pltfrm/pci driver's probe fails for some reason then ensure
that scsi host is released to avoid memory leak but managed memory
allocations (via devm_* calls) need not to be freed explicitly on probe
failure as memory allocated with these functions is automatically freed
on driver detach.

Reviewed-by: Sahitya Tummala <stummala@codeaurora.org>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: ufs: fix race between clock gating and devfreq scaling work

UFS devfreq clock scaling work may require clocks to be ON if it need to
execute some UFS commands hence it may request for clock hold before
issuing the command. But if UFS clock gating work is already running in
parallel, ungate work would end up waiting for the clock gating work to
finish and as clock gating work would also wait for the clock scaling
work to finish, we would enter in deadlock state. Here is the call trace
during this deadlock state:

Workqueue: devfreq_wq devfreq_monitor
__switch_to
__schedule
schedule
schedule_timeout
wait_for_common
wait_for_completion
flush_work
ufshcd_hold
ufshcd_send_uic_cmd
ufshcd_dme_get_attr
ufs_qcom_set_dme_vs_core_clk_ctrl_clear_div
ufs_qcom_clk_scale_notify
ufshcd_scale_clks
ufshcd_devfreq_target
update_devfreq
devfreq_monitor
process_one_work
worker_thread
kthread
ret_from_fork

Workqueue: events ufshcd_gate_work
__switch_to
__schedule
schedule
schedule_preempt_disabled
__mutex_lock_slowpath
mutex_lock
devfreq_monitor_suspend
devfreq_simple_ondemand_handler
devfreq_suspend_device
ufshcd_gate_work
process_one_work
worker_thread
kthread
ret_from_fork

Workqueue: events ufshcd_ungate_work
__switch_to
__schedule
schedule
schedule_timeout
wait_for_common
wait_for_completion
flush_work
__cancel_work_timer
cancel_delayed_work_sync
ufshcd_ungate_work
process_one_work
worker_thread
kthread
ret_from_fork

This change fixes this deadlock by doing this in devfreq work (devfreq_wq):
Try cancelling clock gating work. If we are able to cancel gating work
or it wasn't scheduled, hold the clock reference count until scaling is
in progress. If gate work is already running in parallel, let's skip
the frequecy scaling at this time and it will be retried once next scaling
window expires.

Reviewed-by: Sahitya Tummala <stummala@codeaurora.org>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: mpt3sas: Bump driver version as "14.101.00.00"

Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Sathya Prakash <sathya.prakash@broadcom.com>
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: mpt3sas: Fix for Endianness issue.

Use le16_to_cpu only for accessing two byte data provided by controller.

Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Sathya Prakash <sathya.prakash@broadcom.com>
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: mpt3sas: Use the new MPI 2.6 32-bit Atomic Request Descriptors for SAS35 devices.

Support Atomic Request Descriptors for Ventura/SAS35 devices.

Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Sathya Prakash <sathya.prakash@broadcom.com>
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: mpt3sas: set EEDP-escape-flags for SAS35 devices.

An UNMAP command on a PI formatted device will leave the Logical Block
Application Tag and Logical Block Reference Tag as all F's (for those LBAs
that are unmapped). To avoid IO errors if those LBAs are subsequently read
before they are written with valid tag fields, the MPI SCSI IO requests
need to set the EEDPFlags element EEDP Escape Mode field, Bits [7:6]
appropriately. A value of 2 should be set to disable all PI checks if the
Logical Block Application Tag is 0xFFFF for PI types 1 and 2.  A value
of 3 should be set to disable all PI checks if the Logical Block
Application Tag is 0xFFFF and the Logical Block Reference Tag is
0xFFFFFFFF for PI type 3.

Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Sathya Prakash <sathya.prakash@broadcom.com>
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: mpt3sas: Increased/Additional MSIX support for SAS35 devices.

For SAS35 devices MSIX vectors are inceased to 128 from 96. To support this
Reply post host index register count is increased to 16. Also variable
msix96_vector is replaced with combined_reply_queue and variable
combined_reply_index_count is added to set different values for SAS3 and
SAS35 devices.

Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Sathya Prakash <sathya.prakash@broadcom.com>
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: mpt3sas: Added Device ID's for SAS35 devices and updated MPI header.

Added Device ID's for SAS35 devices (Ventura, Crusader, Harpoon &
Tomcat) and updated mpi header file for the same. Also added
"is_gen35_ioc" to MPT3SAS_ADAPTER structure for identifying SAS35 adapters.

Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Sathya Prakash <sathya.prakash@broadcom.com>
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: mpt3sas: Bump driver version as "14.100.00.00"

Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Sathya Prakash <sathya.prakash@broadcom.com>
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: mpt3sas: Remove unused macro "MPT_DEVICE_TLR_ON"

Removing macro "MPT_DEVICE_TLR_ON" defined in header file as its unused

Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Sathya Prakash <sathya.prakash@broadcom.com>
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: mpt3sas: Implement device_remove_in_progress check in IOCTL path

When device missing event arrives, device_remove_in_progress bit will be
set and hence driver has to stop sending IOCTL commands.Now the check has
been added in IOCTL path to test device_remove_in_progress bit is set, if
so then IOCTL will be failed printing failure message.

Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Sathya Prakash <sathya.prakash@broadcom.com>
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: mpt3sas: Fix for incorrect numbers for MSIX vectors enabled when non RDPQ card is enumerated first.

No. of MSIX vectors supported = min (Total no. of CPU cores,
MSIX vectors supported by card)

when RDPQ is disabled "max_msix_vectors" module parameter which was
declared as global was set to '8' and hence if there are more than one card
in system among which if RDPQ disabled card is enumerated first then only 8
MSIX vectors was getting enabled for all the cards(including RDPQ enabled
card,which can support more than 8 MSIX vectors).

Used local variable instead of global variable ,if RDPQ is disabled this
local variable is set to '8' else it is set to "max_msix_vectors" (by
default this is set to -1, whose value can be set by user during driver
load time).So now regardless of whether RDPQ disabled card is enumerated
first or RDPQ enabled card is enumerated first , MSIX vectors enabled
depends on the cards capability.

Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Sathya Prakash <sathya.prakash@broadcom.com>
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: mpt3sas: Fix for improper info displayed in var log, while blocking or unblocking the device.

Return value and Device_handle Arguments passed in correct order
 to match with its format string.

Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Sathya Prakash <sathya.prakash@broadcom.com>
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: advansys: fix build warning for PCI=n

The advansys probe function tries to handle both ISA and PCI cases, each
hidden in an #ifdef when unused. This leads to a warning indicating that
when PCI is disabled we could be using uninitialized data:

drivers/scsi/advansys.c: In function  advansys_board_found :
drivers/scsi/advansys.c:11036:5: error:  ret  may be used uninitialized in this function [-Werror=maybe-uninitialized]
drivers/scsi/advansys.c:10928:28: note:  ret  was declared here
drivers/scsi/advansys.c:11309:8: error:  share_irq  may be used uninitialized in this function [-Werror=maybe-uninitialized]
drivers/scsi/advansys.c:10928:6: note:  share_irq  was declared here

This cannot happen in practice because the hardware in question only
exists for PCI, but changing the code to just error out here is better
for consistency and avoids the warning.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: libfc: Don't have fc_exch_find log errors on a new exchange

With the error message I added in "libfc: sanity check cpu number
extracted from xid" I didn't account for the fact that fc_exch_find is
called with FC_XID_UNKNOWN at the start of a new exchange if we are the
responder.

It doesn't come up with the initiator much, but that's basically every
exchange for a target.  By checking the xid for FC_XID_UNKNOWN first, we
not only prevent the erroneous error message, but skip the unnecessary
lookup attempt as well.

[mkp: applied by hand due to conflict with Hannes' libfc patch series]

Signed-off-by: Chris Leech <cleech@redhat.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: ufs: optimize clock gate work

In a case where gate work is called as part of cancel work from ungate
path the clk state would be marked as REQ_CLKS_ON.  There is no point
gating the clocks and then end up turning them ON immediately in ungate
work, save time by skipping the gate work and change the clk state to
CLKS_ON as they are not turned off yet.

Signed-off-by: Venkat Gopalakrishnan <venkatg@codeaurora.org>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: ufshcd: Fix race between clk scaling and ungate work

The ungate work turns on the clock before it exits hibern8, if the link
was put in hibern8 during clock gating work.  There occurs a race
condition when clock scaling work calls ufshcd_hold() to make sure low
power states cannot be entered, but that returns by checking only
whether the clocks are on.  This causes the clock scaling work to issue
UIC commands when the link is in hibern8 causing failures. Make sure we
exit hibern8 state before returning from ufshcd_hold().

Callstacks for race condition:

 ufshcd_scale_gear
 ufshcd_devfreq_scale
 ufshcd_devfreq_target
 update_devfreq
 devfreq_monitor
 process_one_work
 worker_thread
 kthread
 ret_from_fork

 ufshcd_uic_hibern8_exit
 ufshcd_ungate_work
 process_one_work
 worker_thread
 kthread
 ret_from_fork

Signed-off-by: Venkat Gopalakrishnan <venkatg@codeaurora.org>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: ufs: fail ufshcd_probe_hba() if power configuration fails

In case the power configuration fails, skip further processing of the
probing function and return immediately. This has 2 reasons:

1. Don't allow the UFS to continue running in PWM

2. Avoid multiple calls to pm_runtime_put_sync() when not in error
   handling or power management contexts

Signed-off-by: Dov Levenglick <dovl@codeaurora.org>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: ufs: suspend clock scaling for failed runtime_resume

During runtime resume operation, clock scaling may get indirectly
resumed via call to ufshcd_set_dev_pwr_mode(): Start/Stop Unit command
times out and SCSI error handling ultimately calls the host reset
handler to recover, during which clock scaling is resumed.  Error case
exit path of runtime resume will disable clocks.  As clock scaling was
already resumed, it will get scheduled later on and try to access UFS
registers while clocks are disabled, resulting in unclocked register
access.

Signed-off-by: Gilad Broner <gbroner@codeaurora.org>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: ufs: fix sense buffer size to 18 bytes

According to UFS device specification, sense data can be only 18 bytes
long, this change makes the changes accordingly.

Signed-off-by: Gilad Broner <gbroner@codeaurora.org>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: ufs: commit descriptors before setting the doorbell

Add a write memory barrier to make sure descriptors prepared are
actually written to memory before ringing the doorbell. We have also
added the write memory barrier after ringing the doorbell register so
that controller sees the new request immediately.

Signed-off-by: Gilad Broner <gbroner@codeaurora.org>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: ufs: fix bugs related to null pointer access and array size

In this change there are a few fixes of possible NULL pointer access and
possible access to index that exceeds array boundaries.

Signed-off-by: Yaniv Gardi <ygardi@codeaurora.org>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: cciss: replace custom function to hexdump

For small buffers we may use %*ph[N] specifier, for the bigger blocks
print_hex_dump() call.

Cc: Don Brace <don.brace@microsemi.com>
Cc: esc.storagedev@microsemi.com
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>