Patrick Delaunay [Tue, 28 Jan 2020 09:44:13 +0000 (10:44 +0100)]
board: stm32mp1: change dfu function to static
Change the dfu functions dfu_otp_read and dfu_pmic_read to static,
this patch avoids warning when compiling with W=1.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Patrick Delaunay [Tue, 28 Jan 2020 09:44:12 +0000 (10:44 +0100)]
board: stm32mp1: board: add include for dfu
Add include for dfu, add prototype for set_dfu_alt_info
and avoid warning when compiling with W=1.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Antonio Borneo [Tue, 28 Jan 2020 14:42:13 +0000 (15:42 +0100)]
tools: mkimage: fix STM32 image format for big endian hosts
Two header fields are not properly converted to little endian
before assignment, resulting in incorrect header while executing
mkimage on big endian hosts.
Convert the value of the header fields image_checksum and
edcsa_algorithm to little endian before the assignment.
Signed-off-by: Antonio Borneo <antonio.borneo@st.com>
Reviewed-by: Patrick DELAUNAY <patrick.delaunay@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Patrick Delaunay [Tue, 28 Jan 2020 09:11:06 +0000 (10:11 +0100)]
stm32mp1: support of STM32MP15x Rev.Z
Add support for Rev.Z of STM32MP15x cpu.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Patrick Delaunay [Tue, 28 Jan 2020 09:11:04 +0000 (10:11 +0100)]
board: stm32mp1: update readme
Update readme:
- list the supported SOC and change family to STM32MP15x
- add warning on OTP write and prerequisite:
check if MAC address is not yet provisioned.
- Use filesize for mmc write command (avoid to write all partition
with ${partsize}). ${filesize} and ${partsize} are set by previous
load command.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Patrick Delaunay [Tue, 28 Jan 2020 09:11:03 +0000 (10:11 +0100)]
ARM: dts: stm32m1: add reg for pll nodes
Fix the following DT dtc warnings for stm32mp1 boards:
Warning (unit_address_vs_reg): /soc/rcc@
50000000/st,pll@0:
node has a unit name, but no reg property
Warning (unit_address_vs_reg): /soc/rcc@
50000000/st,pll@1:
node has a unit name, but no reg property
Warning (unit_address_vs_reg): /soc/rcc@
50000000/st,pll@2:
node has a unit name, but no reg property
Warning (unit_address_vs_reg): /soc/rcc@
50000000/st,pll@3:
node has a unit name, but no reg property
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Patrick Delaunay [Tue, 28 Jan 2020 09:11:02 +0000 (10:11 +0100)]
ARM: dts: stm32mp1: correct ddr node
This patch fix the warning:
dt.dts: Warning (simple_bus_reg): Node /soc/ddr@
5A003000
simple-bus unit address format error, expected "
5a003000"
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Antonio Borneo [Tue, 28 Jan 2020 09:11:01 +0000 (10:11 +0100)]
ARM: dts: stm32mp1: move FDCAN to PLL4_R
LTDC modifies the clock frequency to adapt it to the display. Such
frequency change is not detected by the FDCAN driver that instead
cache the value at probe and pretend to use it later.
Keep the LTDC alone on PLL4_Q by moving the FDCAN to PLL4_R.
Signed-off-by: Antonio Borneo <antonio.borneo@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Patrick Delaunay [Tue, 28 Jan 2020 09:11:00 +0000 (10:11 +0100)]
ARM: dts: stm32mp1: DT alignment with kernel v5.5-rc7
Device tree and binding alignment with kernel v5.5-rc7
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Patrick Delaunay [Tue, 28 Jan 2020 09:10:59 +0000 (10:10 +0100)]
stm32mp1: pwr: use the last binding for pwr
Update the driver to use the latest binding from kernel v5.5-rc1:
no more use syscon or regmap to access to pwr register and
only one pwr_regulators node with the compatibility "st,stm32mp1,pwr-reg"
is available.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Patrick Delaunay [Tue, 28 Jan 2020 09:10:58 +0000 (10:10 +0100)]
ARM: dts: stm32mp1: DT alignment with kernel v5.4
Device tree and binding alignment with kernel v5.4
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Marek Vasut [Fri, 24 Jan 2020 17:39:16 +0000 (18:39 +0100)]
ARM: dts: stm32: Add DH Electronics DHCOM SoM and PDK2 board
Add support for DH Electronics DHCOM SoM and PDK2 rev. 400 carrier
board. This is an SoM with STM32MP15xx and an evaluation kit. The
baseboard provides Ethernet, UART, USB, CAN and optional display.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Tom Rini [Wed, 12 Feb 2020 14:30:43 +0000 (09:30 -0500)]
Prepare v2020.04-rc2
Signed-off-by: Tom Rini <trini@konsulko.com>
Simon Glass [Wed, 12 Feb 2020 00:15:19 +0000 (17:15 -0700)]
Revert "gitlab: Disable SDL when building sandbox"
This is not needed now that we have SDL2 in the docker image. It causes
test failures for tests which need video to work.
This reverts commit
af800722eb718bec51c5943cfb69231acf15178f.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tom Rini [Tue, 11 Feb 2020 15:58:41 +0000 (10:58 -0500)]
Merge tag 'dm-pull-6feb20' of https://gitlab.denx.de/u-boot/custodians/u-boot-dm
sandbox conversion to SDL2
TPM TEE driver
Various minor sandbox video enhancements
New driver model core utility functions
Tom Rini [Tue, 11 Feb 2020 12:32:44 +0000 (07:32 -0500)]
Merge branch '2020-02-10-master-imports'
- Regulator fix
- Documentation fix
- Correct LOGLEVEL range
Marek Bykowski [Mon, 3 Feb 2020 10:43:32 +0000 (11:43 +0100)]
Kconfig: update LOGLEVEL range
As LOGLEVEL ranges form 0 to 9 set the limit to 10.
Signed-off-by: Marek Bykowski <marek.bykowski@gmail.com>
Dario Binacchi [Sun, 9 Feb 2020 18:57:41 +0000 (19:57 +0100)]
dm: fix design.rst document
The patch fixes some errors.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Lukasz Majewski [Sat, 25 Jan 2020 08:00:58 +0000 (09:00 +0100)]
regulator: fix: Move code to enable gpio regulator to pre_probe from ofdata_to_platdata
The commit
e8e9715df2d4 ("regulator: fixed: Modify enable-active-high behavior")
fixed the regulator driver behavior when 'enable-active-high' is defined.
Unfortunately, this patch used dm_regulator_platdata()'s "boot_on" member
to set GPIOD_IS_OUT_ACTIVE flag and enable the regulator.
The issue here is that regulator_common_ofdata_to_platdata() is called
_before_ regulator_pre_probe() function in which the 'regulator-boot-on'
property is asserted.
As a result the GPIOD_IS_OUT_ACTIVE flag is not set and gpio_request_by_name()
called in the former function is not enabling the regulator.
This is problematic for e.g. i.MX ethernet driver, which then tries to
perform initialization without power (and fails).
The solution here is to explicitly enable regulator in regulator_pre_probe()
callback only when 'regulator-boot-on' property is present in device tree.
The GPIOD_IS_OUT_ACTIVE flag is not set at all, but relevant gpio is
requested.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Tested-by: Patrice Chotard <patrice.chotard@st.com>
Tom Rini [Mon, 10 Feb 2020 17:27:31 +0000 (12:27 -0500)]
Merge https://gitlab.denx.de/u-boot/custodians/u-boot-x86
- Move P2SB from Apollo Lake to a more generic location
- Add a function to find a device by drvdata in DM core
- Enhancement of DM IRQ uclass driver
- Add a clock driver for Intel devices
- Add support for ACPI general-purpose events
- Add a TPM driver for H1/Cr50
- Enable TPM on Google Chromebook Coral
Tom Rini [Mon, 10 Feb 2020 17:08:51 +0000 (12:08 -0500)]
Merge tag 'fixes-for-v2020.04' of https://gitlab.denx.de/u-boot/custodians/u-boot-video
- fix Coverity CID 280902 issue in vid_console_color()
- fix vid_console_color() build warning
- fix for mxsfb to ensure correct Linux logo position
Tom Rini [Mon, 10 Feb 2020 14:04:11 +0000 (09:04 -0500)]
Merge tag 'u-boot-imx-
20200210' of https://gitlab.denx.de/u-boot/custodians/u-boot-imx
- Convert to DM:
- bx50v3, mx53ppd, novena, mx6sabresd
- Fixes for Xea Board
- Toradex im8m Verdin
- Cleanup (warp7, mx6sxsabresd)
Travis : https://travis-ci.org/sbabic/u-boot-imx/builds/
648131788
Tom Rini [Mon, 10 Feb 2020 12:48:03 +0000 (07:48 -0500)]
Merge https://gitlab.denx.de/u-boot/custodians/u-boot-riscv
- Fix ax25-ae350.rst document.
- Refine RISC-V linker script and start.S.
- Add option to print more information on exception.
Sean Anderson [Mon, 27 Jan 2020 21:39:44 +0000 (16:39 -0500)]
riscv: Remove unnecessary instruction
The add instruction on risc-v can have any three sources and targets, so there
is no need for an intermediate mov.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Jagan Teki [Mon, 30 Dec 2019 14:29:09 +0000 (19:59 +0530)]
doc: fix opensbi build steps for AX25-AE350
OpenSBI build steps are marked as normal text in
AX25-AE350 documentation.
Move them into code-block so-that it can show it
as build steps.
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Heinrich Schuchardt [Fri, 27 Dec 2019 18:50:53 +0000 (19:50 +0100)]
doc: fix AX25-AE350 RISC-V documentation
Since commit
04883bf7acca ("doc: update AX25-AE350 RISC-V documentation")
`make htmldocs` produces a log of warnings like
doc/board/AndesTech/ax25-ae350.rst:373:
WARNING: Block quote ends without a blank line; unexpected unindent.
doc/board/AndesTech/ax25-ae350.rst:0:
WARNING: Undefined substitution referenced: "_ __ ___ _ __ | (___ | |_) |".
Reformat the problematic passages.
Fixes:
04883bf7acca ("doc: update AX25-AE350 RISC-V documentation")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Sean Anderson [Wed, 25 Dec 2019 05:27:44 +0000 (00:27 -0500)]
riscv: Add option to print registers on exception
When debugging, it can be helpful to see more information about an
unhandled exception. This patch adds an option to view the registers at
the time of the trap, similar to the linux output on a kernel panic.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Sean Anderson [Wed, 18 Dec 2019 02:35:32 +0000 (21:35 -0500)]
riscv: Fix breakage caused by linker relaxation
Due to the two-instruction sequence needed to access arbitrary memory
locations, the RISC-V linker aggressively optimises memory accesses and
jumps at link-time. This is called "linker relaxation," and is discussed
in this SiFive article
<https://www.sifive.com/blog/all-aboard-part-3-linker-relaxation-in-riscv-toolchain>.
One of the optimizations in place is to assume that the __global_pointer
symbol is placed in the gp register. To quote the article:
"...The magic __global_pointer$ symbol is defined to point 0x800 bytes
past the start of the .sdata section. The 0x800 magic number allows
signed 12-bit offsets from __global_pointer$ to address symbols at the
start of the .sdata section. The linker assumes that if this symbol is
defined, then the gp register contains that value, which it can then use
to relax accesses to global symbols within that 12-bit range. The
compiler treats the gp register as a constant so it doesn't need to be
saved or restored, which means it is generally only written by _start,
the ELF entry point."
However, U-Boot instead keeps the global data pointer in gp. This causes
memory accesses and jumps optimized to use the gp pointer to fail. To
fix this problem, we undefine the __global_pointer symbol.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Ian Ray [Fri, 31 Jan 2020 13:08:04 +0000 (15:08 +0200)]
board: ge: bx50v3, imx53ppd: configure CONFIG_SYS_BOOTMAPSZ
Configure `CONFIG_SYS_BOOTMAPSZ' per guidance on u-boot@lists.denx.de.
Signed-off-by: Ian Ray <ian.ray@ge.com>
Robert Beckett [Fri, 31 Jan 2020 13:08:03 +0000 (15:08 +0200)]
board: ge: bx50v3, mx53ppd: fix firstboot detection
Use `test' command to test for file existence instead of relying on the
old functionality of the `ext2load' command (which now reports an error
when attempting to load a zero length file).
Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
Signed-off-by: Ian Ray <ian.ray@ge.com>
Ian Ray [Fri, 31 Jan 2020 13:08:02 +0000 (15:08 +0200)]
board: ge: mx53ppd: use DM for uart
Drop PPD_UART_PAD_CTRL since it matches defaults.
Enable DM serial and MXC uart.
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
Robert Beckett [Fri, 31 Jan 2020 13:08:01 +0000 (15:08 +0200)]
board: ge: bx50v3: use DM for uart
Remove legacy uart pad and iomux code
Enable DM serial and mxc uart
Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
Robert Beckett [Fri, 31 Jan 2020 13:08:00 +0000 (15:08 +0200)]
board: ge: mx53ppd: Use DM for ethernet
Remove legacy iomux setup for fec.
Enable phylib and DM fec.
Use Kconfig for enabling fec.
Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
Robert Beckett [Fri, 31 Jan 2020 13:07:59 +0000 (15:07 +0200)]
board: ge: bx50v3: Enable DM PWM for backlight
Add backlight and panel devicetree definitions
Use UCLASS_PANEL to enable backlight via display enable handler
Remove old explicit gpio code for handling backlight
Use cls command to initiate display in HW agnostic manner
Enable DM regulator and pwm
Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
Ian Ray [Fri, 31 Jan 2020 13:07:58 +0000 (15:07 +0200)]
board: ge: bx50v3: override panel
Override the panel compatible string for LCD in U-Boot.
Include U-Boot device tree overrides in device-specific device trees so
that the panel compatible string is used.
Fixes:
8c26739859c6 ("board: ge: bx50v3: sync devicetrees from Linux")
Signed-off-by: Ian Ray <ian.ray@ge.com>
Ian Ray [Fri, 31 Jan 2020 13:07:57 +0000 (15:07 +0200)]
board: ge: mx53ppd: enable DM_VIDEO
Enable DM_VIDEO for mx53ppd.
Enable DM_REGULATOR_FIXED and DM_PWM for the backlight.
Remove unused MX53PPD_LCD_POWER.
Remove old (incorrect) setup_iomux_lcd.
Enable backlight via display enable handler.
Use cls command to initiate display in HW agnostic manner.
Modify `failbootcmd' to use lcdputs.
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
Robert Beckett [Fri, 31 Jan 2020 13:07:56 +0000 (15:07 +0200)]
board: ge: mx53ppd: add i2c eeprom bootcount storage
Add bootcount node, linking to i2c eeprom "bootcount" partitions for
storage.
Enable i2c eeprom bootcount backend storage.
Enable bootcount command and use it for failbootcmd.
Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
Robert Beckett [Fri, 31 Jan 2020 13:07:55 +0000 (15:07 +0200)]
board: ge: bx50v3: add i2c eeprom bootcount storage
Add bootcount node, linking to i2c eeprom "bootcount" partitions for
storage.
Enable i2c eeprom bootcount backend storage.
Enable bootcount command and use it for failbootcmd.
Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
Robert Beckett [Fri, 31 Jan 2020 13:07:54 +0000 (15:07 +0200)]
board: ge: bx50v3, imx53ppd: use DM I2C
Remove old (pre-DM) i2c setup code.
Enable DM i2c.
Convert common code to use DM rtc.
Convert common code to read VPD from eeprom partition.
Convert the generic i2c PMIC init code to use the new da9063 driver.
mx53ppd only:
Correct RTC compatible in device tree.
Enable MXC DM i2c driver.
Define CONFIG_SYS_MALLOC_F_LEN so that DM is available in pre-reloc.
Make GPIO banks available during preloc, since initialisation is done
in board_early_init_f().
Add gpio_request() calls to satisfy the DM_GPIO compatibility API.
Remove unused power configuration.
Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
Signed-off-by: Ian Ray <ian.ray@ge.com>
Robert Beckett [Fri, 31 Jan 2020 13:07:53 +0000 (15:07 +0200)]
board: ge: bx50v3, imx53ppd: add eeprom partitions
Add eeprom partitions to device tree.
Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
Robert Beckett [Fri, 31 Jan 2020 13:07:52 +0000 (15:07 +0200)]
misc: i2c_eeprom: set offset len and chip addr offset mask
Set the correct offset length and chip address offset mask for each
device to allow correct access to total capacity of the devices.
Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
Anatolij Gustschin [Sat, 25 Jan 2020 23:35:59 +0000 (00:35 +0100)]
imx: mx6ul_14x14_evk: turn of backlight and LCD before booting OS
This should help keeping the screen black when booting the kernel.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Reported-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Fabio Estevam <festevam@gmail.com>
Alifer Moraes [Mon, 20 Jan 2020 16:31:02 +0000 (13:31 -0300)]
mx6sabresd: Convert PCI to driver model
Convert imx6sabresd PCI to driver model to fix the following warning:
===================== WARNING ======================
This board does not use CONFIG_DM_PCI Please update
the board to use CONFIG_DM_PCI before the v2019.07 release.
Failure to update by the deadline may result in board removal.
See doc/driver-model/MIGRATION.txt for more info.
====================================================
After the conversion the following commands were used for testing:
=> pci enum
PCI: Failed autoconfig bar 10
PCI: Failed autoconfig bar 10
=> pci 1
Scanning PCI devices on bus 1
BusDevFun VendorId DeviceId Device Class Sub-Class
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Fabio Estevam [Mon, 20 Jan 2020 16:31:01 +0000 (13:31 -0300)]
mx6sabre_common: Remove FEC related settings
In preparation for converting to DM_ETH and moving the FEC symbols
to Kconfig we need to move the FEC definitions to mx6sabreauto.h
and mx6sabresd.h to avoid build breakage during the conversion.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Alifer Moraes <alifer.wsdm@gmail.com>
Heiko Schocher [Thu, 30 Jan 2020 13:10:05 +0000 (14:10 +0100)]
imx6: aristainetos: fix NAND detection with latest mainline
commit
88718be30010 ("mtd: rename CONFIG_NAND -> CONFIG_MTD_RAW_NAND")
moved CONFIG_NAND -> CONFIG_MTD_RAW_NAND. Adapt board code to this
change, as last merge did not respect the above commit.
Signed-off-by: Heiko Schocher <hs@denx.de>
Marek Vasut [Mon, 27 Jan 2020 00:15:28 +0000 (01:15 +0100)]
ARM: imx: novena: Enable DM thermal
Enable DM thermal driver and iMX thermal driver to get accurate
CPU frequency reporting in the boot log.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Vagrant Cascadian <vagrant@debian.org>
Marek Vasut [Mon, 27 Jan 2020 00:15:27 +0000 (01:15 +0100)]
ARM: imx: novena: Enable DM ethernet
Convert to DM ethernet to prevent board removal.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Vagrant Cascadian <vagrant@debian.org>
Marek Vasut [Mon, 27 Jan 2020 00:15:26 +0000 (01:15 +0100)]
ARM: imx: novena: Move defconfig bits to arch Kconfig
Just move the defconfig entries which are required into the Novena
entry in arch Kconfig, no functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Vagrant Cascadian <vagrant@debian.org>
Joris Offouga [Wed, 29 Jan 2020 21:06:01 +0000 (22:06 +0100)]
mx7dsabre: Fix usbtog probe when use dfu or ums
Before:
=> ums 0 mmc 0
UMS: LUN 0, dev 0, hwpart 0, sector 0x0, count 0x1dacc00
usb dr_mode not found
CTRL+C - Operation aborted
=> dfu 0 mmc 0
usb dr_mode not found
After :
=> ums 0 mmc 0
UMS: LUN 0, dev 0, hwpart 0, sector 0x0, count 0x1dacc00
=> dfu 0 mmc 0
Signed-off-by: Joris Offouga <offougajoris@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Joris Offouga [Wed, 29 Jan 2020 21:06:00 +0000 (22:06 +0100)]
arm: dts: imx7s-warp7: Move u-boot specific node in u-boot.dtsi
These nodes are not in upstream kernel, so move these in u-boot.dtsi
Signed-off-by: Joris Offouga <offougajoris@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Joris Offouga [Wed, 29 Jan 2020 21:05:59 +0000 (22:05 +0100)]
warp7: remove unused usb configs
With commit
6b503f9e6549("warp7: Switch to DM USB").
These configs are not necessary
Signed-off-by: Joris Offouga <offougajoris@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Joris Offouga [Wed, 29 Jan 2020 21:05:58 +0000 (22:05 +0100)]
warp7: Fix the pmic_get() parameter in the DM case
When pmic_get() is used with DM the first parameter must be
the complete node name plus the unit address, so fix it
accordingly
Signed-off-by: Joris Offouga <offougajoris@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Lukasz Majewski [Sat, 25 Jan 2020 08:01:40 +0000 (09:01 +0100)]
arm: xea: dts: Add 'fec-3v3' regulator properties to prevent accidental disablement
The 'enable-active-high' DTS property configures GPIO so it is active with
HIGH state (by default it is low).
The 'regulator-boot-on' property indicates that the regulator was enabled
in the 'earlier' stage - i.e. bootloader/firmware.
In the XEA case the 'fec-3v3' was configured (as a "wrapper" on GPIO0_0) in
very early SPL code, so it shouldn't be modified at latter stages.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Lukasz Majewski [Sat, 25 Jan 2020 08:01:39 +0000 (09:01 +0100)]
arm: xea: spl: Add GPIO0_0 setup on spl_board_init
Explicitly configure GPIO0_0 in SPL, which controlls 3V3 voltage
on the XEA board (it also supplies TIVAs).
This code would enable TIVAs power supply early (also when board
uses the falcon boot).
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Lukasz Majewski [Sat, 25 Jan 2020 08:01:38 +0000 (09:01 +0100)]
arm: xea: config: Enable support for XEA board specific device tree tweaks
This patch enables support for CONFIG_OF_BOARD_SETUP in xea defconfig.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Lukasz Majewski [Sat, 25 Jan 2020 08:01:37 +0000 (09:01 +0100)]
arm: xea: Provide function to set L2 switch 'local-mac-address' property
The 'local-mac-address' property needs to be adjusted to the MAC address
value stored in U-Boot's 'ethaddr' env variable.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Lukasz Majewski [Sat, 25 Jan 2020 08:01:36 +0000 (09:01 +0100)]
arm: xea: defconfig: Define space for redundant envs in SPI-NOR flash
Redundant envs help with assuring better reliability for the system as they
prevent from the situation when envs are stored only in a single place.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Fabio Estevam [Tue, 21 Jan 2020 13:30:09 +0000 (10:30 -0300)]
mx7ulp_com: Remove unneeded SoC definitions
Since commit
9c27310ac23c ("mx7ulp: Move SoC base address to a common
file") we no longer need to have these SoC definitions in the board
file, so remove them.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Joel Johnson [Wed, 29 Jan 2020 16:17:18 +0000 (09:17 -0700)]
cmd: mdc/mwc: normalize disjoint MX_CYCLIC usage
Both CMD_MX_CYCLIC and MX_CYCLIC are in use and defined in Kconfig,
but only the non-CMD version currently does anything. This changes all
usages to prefer the CMD_MX_CYCLIC option (since it's only affecting
addition of the commands), and switches defconfigs using the non-CMD
version to use the CMD version.
Signed-off-by: Joel Johnson <mrjoel@lixil.net>
Reviewed-by: Tom Rini <trini@konsulko.com>
Sébastien Szymanski [Tue, 21 Jan 2020 10:58:42 +0000 (11:58 +0100)]
tools: imx8m_image: fix warning message
When a firmware file is missing the warning message doesn't indicate the
firmware file name because '$tmp' var doesn't exist.
Fix the warning message and while at it reduce the if/else statement.
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Fabio Estevam [Mon, 27 Jan 2020 13:33:50 +0000 (10:33 -0300)]
mx6sxsabresd: Keep only one target
Currently there are two targets for the i.MX6SX SabreSD board:
mx6sxsabresd_defconfig and mx6sxsabresd_spl_defconfig.
This brings additional maintainance effort without a clear
advantage.
Keep only the mx6sxsabresd_defconfig one and remove
mx6sxsabresd_spl_defconfig to keep it simpler.
Also remove the SPL related code from the board file.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Fabio Estevam [Wed, 29 Jan 2020 16:58:03 +0000 (13:58 -0300)]
mx6ul_14x14_evk: Move CONFIG_DM_74X164 to defconfig
The CONFIG_DM_74X164 symbols should be moved to the defconfig file,
as indicated in the comments.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Fabio Estevam [Wed, 29 Jan 2020 16:58:02 +0000 (13:58 -0300)]
gpio: Let DM_74X164 be built without CONFIG_SPL_GPIO
Since commit
bcee8d6764f9 ("dm: gpio: Allow control of GPIO uclass in SPL")
CONFIG_DM_74X164 is no longer built for mx7dsabresd_defconfig, as
this target does not use CONFIG_SPL_GPIO.
Remove such dependency and let the the 74X164 GPIO driver be built
again.
This restores Ethernet functionality on the imx7-sdb board as the
Ethernet reset PHY comes from a GPIO driven by a 74LV595PW I/O
expander.
Fixes:
bcee8d6764f9 ("dm: gpio: Allow control of GPIO uclass in SPL")
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Tested-by: Alifer Moraes <alifer.wsdm@gmail.com>
Marcel Ziswiler [Tue, 28 Jan 2020 13:42:28 +0000 (14:42 +0100)]
imx: imx8mm_evk: spelling in readme file
Minor spelling fix in README file.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Igor Opaniuk [Tue, 28 Jan 2020 13:42:27 +0000 (14:42 +0100)]
board: toradex: verdin-imx8mm: add MAINTAINERS
Assign Igor Opaniuk as a board maintainer.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Igor Opaniuk [Tue, 28 Jan 2020 13:42:26 +0000 (14:42 +0100)]
board: toradex: verdin-imx8mm: add README
Add README with build steps for U-boot and TF-A for Verdin iMX8M Mini SoM.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Igor Opaniuk [Tue, 28 Jan 2020 13:42:25 +0000 (14:42 +0100)]
board: toradex: Add Verdin iMX8M Mini support
This adds initial minimal support for the Toradex Verdin iMX8M Mini Quad
2GB WB IT V1.0A module. They are now strapped to boot from eFuses which
are factory fused to properly boot from their on-module eMMC. U-Boot
supports booting from the on-module eMMC only, SDP support is disabled
for now due to missing i.MX 8M Mini USB support.
Functionality wise the following is known to be working:
- eMMC, 8-bit and 4-bit MMC/SD card slots
- Ethernet
- GPIOs
- I2C
Boot sequence is:
SPL ---> ATF (TF-A) ---> U-boot proper
ATF, U-boot proper and u-boot.dtb images are packed into a FIT image,
loaded by SPL.
Boot:
U-Boot SPL 2020.01-00187-gd411d164e5 (Jan 26 2020 - 04:47:26 +0100)
Normal Boot
Trying to boot from MMC1
NOTICE: Configuring TZASC380
NOTICE: RDC off
NOTICE: BL31: v2.0(release):rel_imx_4.14.98_2.3.0-0-g09c5cc994-dirty
NOTICE: BL31: Built : 01:11:41, Jan 25 2020
NOTICE: sip svc init
U-Boot 2020.01-00187-gd411d164e5 (Jan 26 2020 - 04:47:26 +0100)
CPU: Freescale i.MX8MMQ rev1.0 at 0 MHz
Reset cause: POR
DRAM: 2 GiB
MMC: FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2
Loading Environment from MMC... OK
In: serial
Out: serial
Err: serial
Model: Toradex Verdin iMX8M Mini Quad 2GB Wi-Fi / BT IT V1.0A, Serial#
06535149
Net: eth0: ethernet@
30be0000
Hit any key to stop autoboot: 0
Verdin iMX8MM #
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Marcel Ziswiler [Tue, 28 Jan 2020 13:42:24 +0000 (14:42 +0100)]
toradex: tdx-cfg-block: add Verdin iMX8M Mini/Nano support
Add support for storing configuration for Verdin iMX8M Mini and
Nano SoMs in Toradex config block.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Marcel Ziswiler [Tue, 28 Jan 2020 13:42:23 +0000 (14:42 +0100)]
toradex: tdx-cfg-block: add Apalis iMX8X support
Add support for storing configuration for Apalis iMX8X SoM
in Toradex config block.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Marcel Ziswiler [Tue, 28 Jan 2020 13:42:22 +0000 (14:42 +0100)]
arm: dts: imx8mm-pinfunc: sync latest linux-next pin func header
Synchronise with latest linux-next kernel pin func header file.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Tom Rini [Sat, 8 Feb 2020 00:04:23 +0000 (19:04 -0500)]
Merge branch '2020-02-07-master-imports'
- 2 FAT fixes.
- MediaTek ethernet support improvement.
- Initial Cortina Access CAxxxx family support.
- Correct return value of do_gpio() and so gpio shell command.
Alex Nemirovsky [Thu, 30 Jan 2020 20:34:59 +0000 (12:34 -0800)]
board: presidio-asic: Add basic G3 engr. development board support
Add basic Presidio G3 engineering board support
Signed-off-by: Alex Nemirovsky <alex.nemirovsky@cortina-access.com>
Jason Li [Thu, 30 Jan 2020 20:34:58 +0000 (12:34 -0800)]
serial: serial_cortina: add UART DM driver for CAxxxx SoCs
Add serial UART driver support for all Cortina Access
CAxxxx family of SoCs.
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Jason Li <jason.li@cortina-access.com>
Signed-off-by: Alex Nemirovsky <alex.nemirovsky@cortina-access.com>
Jason Li [Thu, 30 Jan 2020 20:34:57 +0000 (12:34 -0800)]
watchdog: cortina_wdt: add support for HW WDT on CAxxxx SoCs
Add support for hardware watchdog timer on all Cortina Access
CAxxxx family of SoCs.
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Jason Li <jason.li@cortina-access.com>
Signed-off-by: Alex Nemirovsky <alex.nemirovsky@cortina-access.com>
Jason Li [Thu, 30 Jan 2020 20:34:56 +0000 (12:34 -0800)]
gpio: cortina_gpio: add DM_GPIO driver for CAxxxx SoCs
DM_GPIO based GPIO controller driver for CAxxxx SoCs.
This driver support multiple CPU architectures and
Cortina Access SoC platforms.
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Jason Li <jason.li@cortina-access.com>
Signed-off-by: Alex Nemirovsky <alex.nemirovsky@cortina-access.com>
Jason Li [Thu, 30 Jan 2020 20:34:55 +0000 (12:34 -0800)]
gpio: do not include <asm/arch/gpio.h> for Cortina CAxxxx SoCs
The Cortina CAxxxx GPIO driver maintains DM_GPIO support
across different CPU ISA in the CAxxxx Soc Family; Not just ARM.
Therefore, it is not desirable to split out and maintain separete
gpio header file for each CPU architecture.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Jason Li <jason.li@cortina-access.com>
Signed-off-by: Alex Nemirovsky <alex.nemirovsky@cortina-access.com>
Alex Nemirovsky [Thu, 30 Jan 2020 20:34:54 +0000 (12:34 -0800)]
MAINTAINERS, git-mailrc: cortina: add Custodian for Cortina Access Inc.
Assign Alex Nemirovsky as custodian for all
Cortina Access (CA) for ARM and MIPS based SoCs.
Currently Cortina Access CAxxxx family of SoCs support both
ARM and MIPS ISA. Drivers have cross platform support for
both architectures.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Alex Nemirovsky <alex.nemirovsky@cortina-access.com>
Tom Rini [Wed, 29 Jan 2020 16:07:19 +0000 (11:07 -0500)]
mpc8xx: Expose show_regs()
To match the other PowerPC platforms the function show_regs() must not
be marked static but instead be an exposed global function.
Cc: Christophe Leroy <christophe.leroy@c-s.fr>
Cc: Wolfgang Denk <wd@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Christophe Leroy <christophe.leroy@c-s.fr>
Tom Rini [Wed, 29 Jan 2020 16:03:34 +0000 (11:03 -0500)]
cmd/elf.c: Add SPDX tag
Based on reading the text of the license comment this appears to be
the BSD-2-Clause license but with an imperfect word match as
BSD-2-Clause was not (as far as I recall) a common license choice at the
time the code was written.
Cc: Wolfgang Denk <wd@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
MarkLee [Tue, 21 Jan 2020 11:32:00 +0000 (19:32 +0800)]
configs: mediatek: enable mt7622 ethernet support
This patch enable mt7622 ethernet support in its defconfig
Signed-off-by: MarkLee <Mark-MC.Lee@mediatek.com>
Frank Wunderlich [Fri, 31 Jan 2020 09:23:29 +0000 (10:23 +0100)]
eth: mtk-eth: aarch64: fix build warnings on ethernet-driver
building mtk ethernet driver for aarch64 (mt7622) results
in warnings/errors
"error: cast from pointer to integer of different size"
Fixes:
23f17164d9 ("ethernet: MediaTek: add ethernet driver for MediaTek ARM-based SoCs")
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
MarkLee [Tue, 21 Jan 2020 11:31:59 +0000 (19:31 +0800)]
arm: dts: mediatek: add ethernet and sgmii dts node for mt7622
This patch add eth and sgmii dts node for mt7622 to support ethernet
Signed-off-by: MarkLee <Mark-MC.Lee@mediatek.com>
MarkLee [Tue, 21 Jan 2020 11:31:58 +0000 (19:31 +0800)]
eth: mtk-eth: add mt7622 support in mediatek eth driver
This patch add mt7622 support in mediatek eth driver
Signed-off-by: MarkLee <Mark-MC.Lee@mediatek.com>
MarkLee [Tue, 21 Jan 2020 11:31:57 +0000 (19:31 +0800)]
eth: mtk-eth: add sgmii mode support in mediatek eth driver
This patch add sgmii init part for the mediatek SoC that
support sgmii mode. It is a must for mt7622.
Signed-off-by: MarkLee <Mark-MC.Lee@mediatek.com>
Marek Szyprowski [Mon, 2 Dec 2019 11:11:14 +0000 (12:11 +0100)]
fat: write: adjust data written in each partial write
The code for handing file overwrite incorrectly calculated the amount of
data to write when writing to the last non-cluster aligned chunk. Fix
this by ensuring that no more data than the 'filesize' is written to disk.
While touching min()-based calculations, change it to type-safe min_t()
function.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
This patch finally fixes the issue revealed by the test script from the
previous patch. The correctness of the change has been also verified by
the following additional test scripts:
--->8-fat_test2.sh---
#!/bin/bash
make sandbox_defconfig
make
dd if=/dev/zero of=/tmp/10M.img bs=1024 count=10k
mkfs.vfat -v /tmp/10M.img
cat >/tmp/cmds <<EOF
x
host bind 0 /tmp/10M.img
fatls host 0
mw 0x1000000 0x0a434241 0x1000 # "ABC\n"
mw 0x1100000 0x0a464544 0x8000 # "DEF\n"
fatwrite host 0 0x1000000 file0001.raw 0x1000
fatwrite host 0 0x1000000 file0002.raw 0x1000
fatwrite host 0 0x1000000 file0003.raw 0x1000
fatwrite host 0 0x1000000 file0004.raw 0x1000
fatwrite host 0 0x1000000 file0005.raw 0x1000
fatrm host 0 file0002.raw
fatrm host 0 file0004.raw
fatls host 0
fatwrite host 0 0x1100000 file0007.raw 0x2000
fatwrite host 0 0x1100000 file0007.raw 0x1f00
reset
EOF
./u-boot </tmp/cmds
#verify
rm -r /tmp/result /tmp/model
mkdir /tmp/result
mkdir /tmp/model
yes ABC | head -c 4096 >/tmp/model/file0001.raw
yes ABC | head -c 4096 >/tmp/model/file0003.raw
yes ABC | head -c 4096 >/tmp/model/file0005.raw
yes DEF | head -c 7936 >/tmp/model/file0007.raw
mcopy -n -i /tmp/10M.img ::file0001.raw /tmp/result
mcopy -n -i /tmp/10M.img ::file0003.raw /tmp/result
mcopy -n -i /tmp/10M.img ::file0005.raw /tmp/result
mcopy -n -i /tmp/10M.img ::file0007.raw /tmp/result
hd /tmp/10M.img
if diff -urq /tmp/model /tmp/result
then
echo Test okay
else
echo Test fail
fi
--->8-fat_test3.sh---
#!/bin/bash
make sandbox_defconfig
make
dd if=/dev/zero of=/tmp/10M.img bs=1024 count=10k
mkfs.vfat -v /tmp/10M.img
cat >/tmp/cmds <<EOF
x
host bind 0 /tmp/10M.img
fatls host 0
mw 0x1000000 0x0a434241 0x1000 # "ABC\n"
mw 0x1100000 0x0a464544 0x8000 # "DEF\n"
fatwrite host 0 0x1000000 file0001.raw 0x1000
fatwrite host 0 0x1000000 file0002.raw 0x1000
fatwrite host 0 0x1000000 file0003.raw 0x1000
fatwrite host 0 0x1000000 file0004.raw 0x1000
fatwrite host 0 0x1000000 file0005.raw 0x1000
fatrm host 0 file0002.raw
fatrm host 0 file0004.raw
fatls host 0
fatwrite host 0 0x1100000 file0007.raw 0x2000
fatwrite host 0 0x1100000 file0007.raw 0x2100
reset
EOF
./u-boot </tmp/cmds
#verify
rm -r /tmp/result /tmp/model
mkdir /tmp/result
mkdir /tmp/model
yes ABC | head -c 4096 >/tmp/model/file0001.raw
yes ABC | head -c 4096 >/tmp/model/file0003.raw
yes ABC | head -c 4096 >/tmp/model/file0005.raw
yes DEF | head -c 8448 >/tmp/model/file0007.raw
mcopy -n -i /tmp/10M.img ::file0001.raw /tmp/result
mcopy -n -i /tmp/10M.img ::file0003.raw /tmp/result
mcopy -n -i /tmp/10M.img ::file0005.raw /tmp/result
mcopy -n -i /tmp/10M.img ::file0007.raw /tmp/result
hd /tmp/10M.img
if diff -urq /tmp/model /tmp/result
then
echo Test okay
else
echo Test fail
fi
--->8-fat_test4.sh---
#!/bin/bash
make sandbox_defconfig
make
dd if=/dev/zero of=/tmp/10M.img bs=1024 count=10k
mkfs.vfat -v /tmp/10M.img
cat >/tmp/cmds <<EOF
x
host bind 0 /tmp/10M.img
fatls host 0
mw 0x1000000 0x0a434241 0x1000 # "ABC\n"
mw 0x1100000 0x0a464544 0x8000 # "DEF\n"
mw 0x1200000 0x0a494847 0x8000 # "GHI\n"
fatwrite host 0 0x1000000 file0001.raw 0x1000
fatwrite host 0 0x1000000 file0002.raw 0x1000
fatwrite host 0 0x1000000 file0003.raw 0x1000
fatwrite host 0 0x1000000 file0004.raw 0x1000
fatwrite host 0 0x1000000 file0005.raw 0x1000
fatrm host 0 file0002.raw
fatrm host 0 file0004.raw
fatls host 0
fatwrite host 0 0x1100000 file0007.raw 0x900
fatwrite host 0 0x1200000 file0007.raw 0x900 0x900
fatwrite host 0 0x1100000 file0007.raw 0x900 0x1200
fatwrite host 0 0x1200000 file0007.raw 0x900 0x1b00
reset
EOF
./u-boot </tmp/cmds
#verify
rm -r /tmp/result /tmp/model
mkdir /tmp/result
mkdir /tmp/model
yes ABC | head -c 4096 >/tmp/model/file0001.raw
yes ABC | head -c 4096 >/tmp/model/file0003.raw
yes ABC | head -c 4096 >/tmp/model/file0005.raw
yes DEF | head -c 2304 >/tmp/model/file0007.raw
yes GHI | head -c 2304 >>/tmp/model/file0007.raw
yes DEF | head -c 2304 >>/tmp/model/file0007.raw
yes GHI | head -c 2304 >>/tmp/model/file0007.raw
mcopy -n -i /tmp/10M.img ::file0001.raw /tmp/result
mcopy -n -i /tmp/10M.img ::file0003.raw /tmp/result
mcopy -n -i /tmp/10M.img ::file0005.raw /tmp/result
mcopy -n -i /tmp/10M.img ::file0007.raw /tmp/result
hd /tmp/10M.img
if diff -urq /tmp/model /tmp/result
then
echo Test okay
else
echo Test fail
fi
--->8---
Feel free to prepare a proper sandbox/py_test based tests based on
the provided test scripts.
Marek Szyprowski [Mon, 2 Dec 2019 11:11:13 +0000 (12:11 +0100)]
fat: write: fix broken write to fragmented files
The code for handing file overwrite incorrectly assumed that the file on
disk is always contiguous. This resulted in corrupting disk structure
every time when write to existing fragmented file happened. Fix this
by adding proper check for cluster discontinuity and adjust chunk size
on each partial write.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
This patch partially fixes the issue revealed by the following test
script:
--->8-fat_test1.sh---
#!/bin/bash
make sandbox_defconfig
make
dd if=/dev/zero of=/tmp/10M.img bs=1024 count=10k
mkfs.vfat -v /tmp/10M.img
cat >/tmp/cmds <<EOF
x
host bind 0 /tmp/10M.img
fatls host 0
mw 0x1000000 0x0a434241 0x1000 # "ABC\n"
mw 0x1100000 0x0a464544 0x8000 # "DEF\n"
fatwrite host 0 0x1000000 file0001.raw 0x1000
fatwrite host 0 0x1000000 file0002.raw 0x1000
fatwrite host 0 0x1000000 file0003.raw 0x1000
fatwrite host 0 0x1000000 file0004.raw 0x1000
fatwrite host 0 0x1000000 file0005.raw 0x1000
fatrm host 0 file0002.raw
fatrm host 0 file0004.raw
fatls host 0
fatwrite host 0 0x1100000 file0007.raw 0x4000
fatwrite host 0 0x1100000 file0007.raw 0x4000
reset
EOF
./u-boot </tmp/cmds
#verify
rm -r /tmp/result /tmp/model
mkdir /tmp/result
mkdir /tmp/model
yes ABC | head -c 4096 >/tmp/model/file0001.raw
yes ABC | head -c 4096 >/tmp/model/file0003.raw
yes ABC | head -c 4096 >/tmp/model/file0005.raw
yes DEF | head -c 16384 >/tmp/model/file0007.raw
mcopy -n -i /tmp/10M.img ::file0001.raw /tmp/result
mcopy -n -i /tmp/10M.img ::file0003.raw /tmp/result
mcopy -n -i /tmp/10M.img ::file0005.raw /tmp/result
mcopy -n -i /tmp/10M.img ::file0007.raw /tmp/result
hd /tmp/10M.img
if diff -urq /tmp/model /tmp/result
then
echo Test okay
else
echo Test fail
fi
--->8---
Overwritting a discontiguous test file (file0007.raw) no longer causes
corruption to file0003.raw, which's data lies between the chunks of the
test file. The amount of data written to disk is still incorrect, what
causes damage to the file (file0005.raw), which's data lies next to the
test file. This will be fixed by the next patch.
Feel free to prepare a proper sandbox/py_test based tests based on the
provided test scripts.
Luka Kovacic [Sun, 5 Jan 2020 19:10:56 +0000 (20:10 +0100)]
cmd: gpio: Correct do_gpio() return value
Use the correct return value in function do_gpio() and update
commands documentation with the return values from command_ret_t enum.
CMD_RET_SUCCESS is returned on command success and CMD_RET_FAILURE is
returned on command failure.
The command was returning the pin value, which caused confusion when
debugging (#define DEBUG).
Signed-off-by: Luka Kovacic <luka.kovacic@sartura.hr>
Tested-by: Robert Marko <robert.marko@sartura.hr>
Tom Rini [Fri, 7 Feb 2020 16:47:28 +0000 (11:47 -0500)]
azure/gitlab: Update to Docker to have SDL2 available
Update to a newer Docker image that contains SDL2 libraries as required
by recent Sandbox changes.
Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Fri, 7 Feb 2020 16:45:55 +0000 (11:45 -0500)]
azure: Use our own GRUB binaries
Use the same logic from
24df1b14f3ab to use our own GRUB binaries in
Azure pipelines as well.
Signed-off-by: Tom Rini <trini@konsulko.com>
Heinrich Schuchardt [Thu, 19 Dec 2019 12:30:32 +0000 (13:30 +0100)]
gitlab: use our own GRUB
Up to now we have been relying on openSUSE repositories for GRUB on arm and
arm64 though we have included GRUB in our Docker image.
Use the GRUB included in our Docker image.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Simon Glass [Thu, 6 Feb 2020 16:55:05 +0000 (09:55 -0700)]
x86: coral: Enable TPM
Enable TPM2 so that we can use cr50.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Thu, 6 Feb 2020 16:55:04 +0000 (09:55 -0700)]
tpm: Add a driver for H1/Cr50
H1 is a Google security chip present in recent Chromebooks, Pixel phones
and other devices. Cr50 is the name of the software that runs on H1 in
Chromebooks.
This chip is used to handle TPM-like functionality and also has quite a
few additional features.
Add a driver for this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Thu, 6 Feb 2020 16:55:03 +0000 (09:55 -0700)]
tpm: Add more TPM2 definitions
Add definitions for access and status.
Need to drop the mixed case.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Thu, 6 Feb 2020 16:55:02 +0000 (09:55 -0700)]
x86: coral: Add I2C and TPM device-tree definitions
Add nodes to the device tree for Cr50 and other available I2C ports. Also
enable the ACPI interrupt driver.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Thu, 6 Feb 2020 16:55:01 +0000 (09:55 -0700)]
x86: Add support for ACPI general-purpose events
ACPI GPEs are used to signal interrupts from peripherals that are accessed
via ACPI. In U-Boot these are modelled as interrupts using a separate
interrupt controller. Configuration is via the device tree.
Add a simple driver for this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Thu, 6 Feb 2020 16:55:00 +0000 (09:55 -0700)]
dm: irq: Add support for requesting interrupts
At present driver model supports the IRQ uclass but there is no way to
request a particular interrupt for a driver.
Add a mechanism, similar to clock and reset, to read the interrupts
required by a device from the device tree and to request those interrupts.
U-Boot itself does not have interrupt-driven handlers, so just provide a
means to read and clear an interrupt. This can be useful to handle
peripherals which must use an interrupt to determine when data is
available, for example.
Bring over the basic binding file as well, from Linux v5.4. Note that the
older binding is not supported in U-Boot; the newer 'special form' must be
used.
Add a simple test of the new functionality.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Thu, 6 Feb 2020 16:54:59 +0000 (09:54 -0700)]
x86: itss: Add of-platdata support
Allow this driver to be used in TPL by setting up the interrupt type
correctly.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Thu, 6 Feb 2020 16:54:58 +0000 (09:54 -0700)]
x86: Give each driver an IRQ type
Add an IRQ type to each driver and use irq_first_device_type() to find
and probe the correct one.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Thu, 6 Feb 2020 16:54:57 +0000 (09:54 -0700)]
dm: irq: Add support for interrupt controller types
There can be different types of interrupt controllers in a system and some
drivers may need to distinguish between these. In general this can be
handled using the device tree by adding the interrupt information to
device nodes.
However on x86 devices we have interrupt controllers which are not tied
to any particular device and not really used in U-Boot. These still need
to be inited, so a convenient method is to give each controller a type
and allow a particular controller type to be probed.
Add support for this in sandbox along with a test.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: remove the new bland line at EOF of test/dm/irq.c]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Thu, 6 Feb 2020 16:54:56 +0000 (09:54 -0700)]
x86: coral: Update i2c and rtc status
These are actually working correctly, so update the status.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>