review.tizen.org Git - platform/kernel/linux-starfive.git/log

pinctrl: amd: Fix mistake in handling clearing pins at startup

commit a855724dc08b8cb0c13ab1e065a4922f1e5a7552 upstream.

commit 4e5a04be88fe ("pinctrl: amd: disable and mask interrupts on probe")
had a mistake in loop iteration 63 that it would clear offset 0xFC instead
of 0x100. Offset 0xFC is actually `WAKE_INT_MASTER_REG`. This was
clearing bits 13 and 15 from the register which significantly changed the
expected handling for some platforms for GPIO0.

Cc: stable@vger.kernel.org
Link: https://bugzilla.kernel.org/show_bug.cgi?id=217315
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/r/20230421120625.3366-3-mario.limonciello@amd.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

pinctrl: amd: Detect internal GPIO0 debounce handling

commit 968ab9261627fa305307e3935ca1a32fcddd36cb upstream.

commit 4e5a04be88fe ("pinctrl: amd: disable and mask interrupts on probe")
had a mistake in loop iteration 63 that it would clear offset 0xFC instead
of 0x100.  Offset 0xFC is actually `WAKE_INT_MASTER_REG`.  This was
clearing bits 13 and 15 from the register which significantly changed the
expected handling for some platforms for GPIO0.

commit b26cd9325be4 ("pinctrl: amd: Disable and mask interrupts on resume")
actually fixed this bug, but lead to regressions on Lenovo Z13 and some
other systems.  This is because there was no handling in the driver for bit
15 debounce behavior.

Quoting a public BKDG:
```
EnWinBlueBtn. Read-write. Reset: 0. 0=GPIO0 detect debounced power button;
Power button override is 4 seconds. 1=GPIO0 detect debounced power button
in S3/S5/S0i3, and detect "pressed less than 2 seconds" and "pressed 2~10
seconds" in S0; Power button override is 10 seconds
```

Cross referencing the same master register in Windows it's obvious that
Windows doesn't use debounce values in this configuration.  So align the
Linux driver to do this as well.  This fixes wake on lid when
WAKE_INT_MASTER_REG is properly programmed.

Cc: stable@vger.kernel.org
Link: https://bugzilla.kernel.org/show_bug.cgi?id=217315
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/r/20230421120625.3366-2-mario.limonciello@amd.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

pinctrl: amd: Add fields for interrupt status and wake status

commit 010f493d90ee1dbc32fa1ce51398f20d494c20c2 upstream.

If the firmware has misconfigured a GPIO it may cause interrupt
status or wake status bits to be set and not asserted. Add these
to debug output to catch this case.

Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/r/20230328174231.8924-3-mario.limonciello@amd.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

pinctrl: amd: Adjust debugfs output

commit 75358cf3319d5fed595946019deda5c2c26a203d upstream.

More fields are to be added, so to keep the display from being
too busy, adjust it.

1) Add a header to all columns
2) Except for interrupt, when fields have no data show empty
3) Remove otherwise blank whitespace

Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/r/20230328174231.8924-2-mario.limonciello@amd.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

pinctrl: amd: Add Z-state wake control bits

commit df72b4a692b60d3e5d99d9ef662b2d03c44bb9c0 upstream.

GPIO registers include Bit 27 for WakeCntrlZ used to enable wake in
Z state. Hence add Z-state wake control bits to debugfs output to
debug and analyze Z-states problems.

Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Suggested-by: Mario Limonciello <mario.limonciello@amd.com>
Tested-by: Guruvendra Punugupati <Guruvendra.Punugupati@amd.com>
Link: https://lore.kernel.org/r/20221208093704.1151928-1-Basavaraj.Natikar@amd.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

f2fs: fix deadlock in i_xattr_sem and inode page lock

commit 5eda1ad1aaffdfebdecf7a164e586060a210f74f upstream.

Thread #1:

[122554.641906][   T92]  f2fs_getxattr+0xd4/0x5fc
    -> waiting for f2fs_down_read(&F2FS_I(inode)->i_xattr_sem);

[122554.641927][   T92]  __f2fs_get_acl+0x50/0x284
[122554.641948][   T92]  f2fs_init_acl+0x84/0x54c
[122554.641969][   T92]  f2fs_init_inode_metadata+0x460/0x5f0
[122554.641990][   T92]  f2fs_add_inline_entry+0x11c/0x350
    -> Locked dir->inode_page by f2fs_get_node_page()

[122554.642009][   T92]  f2fs_do_add_link+0x100/0x1e4
[122554.642025][   T92]  f2fs_create+0xf4/0x22c
[122554.642047][   T92]  vfs_create+0x130/0x1f4

Thread #2:

[123996.386358][   T92]  __get_node_page+0x8c/0x504
    -> waiting for dir->inode_page lock

[123996.386383][   T92]  read_all_xattrs+0x11c/0x1f4
[123996.386405][   T92]  __f2fs_setxattr+0xcc/0x528
[123996.386424][   T92]  f2fs_setxattr+0x158/0x1f4
    -> f2fs_down_write(&F2FS_I(inode)->i_xattr_sem);

[123996.386443][   T92]  __f2fs_set_acl+0x328/0x430
[123996.386618][   T92]  f2fs_set_acl+0x38/0x50
[123996.386642][   T92]  posix_acl_chmod+0xc8/0x1c8
[123996.386669][   T92]  f2fs_setattr+0x5e0/0x6bc
[123996.386689][   T92]  notify_change+0x4d8/0x580
[123996.386717][   T92]  chmod_common+0xd8/0x184
[123996.386748][   T92]  do_fchmodat+0x60/0x124
[123996.386766][   T92]  __arm64_sys_fchmodat+0x28/0x3c

Cc: <stable@vger.kernel.org>
Fixes: 27161f13e3c3 "f2fs: avoid race in between read xattr & write xattr"
Reviewed-by: Chao Yu <chao@kernel.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

f2fs: fix the wrong condition to determine atomic context

commit 633c8b9409f564ce4b7f7944c595ffac27ed1ff4 upstream.

Should use !in_task for irq context.

Cc: stable@vger.kernel.org
Fixes: 1aa161e43106 ("f2fs: fix scheduling while atomic in decompression path")
Reviewed-by: Chao Yu <chao@kernel.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/amd/pm: add abnormal fan detection for smu 13.0.0

commit 2da0036ea99bccb27f7fe3cf2aa2900860e9be46 upstream.

add abnormal fan detection for smu 13.0.0

Signed-off-by: Kenneth Feng <kenneth.feng@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/amdgpu: Fix minmax warning

commit abd51738fe754a684ec44b7a9eca1981e1704ad9 upstream.

Fix minmax warning by using min_t() macro and explicitly specifying
the assignment type.

Cc: Alex Deucher <Alexander.Deucher@amd.com>
Signed-off-by: Luben Tuikov <luben.tuikov@amd.com>
Reviewed-by: Alex Deucher <Alexander.Deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/amdgpu: add the fan abnormal detection feature

commit ef5fca9f7294509ee5013af9e879edc5837c1d6c upstream.

Update the SW CTF limit from existing register
when there's a fan failure detected via SMU interrupt.

Signed-off-by: lyndonli <Lyndon.Li@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Kenneth Feng <kenneth.feng@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/amd/pm: revise the ASPM settings for thunderbolt attached scenario

commit fd21987274463a439c074b8f3c93d3b132e4c031 upstream.

Also, correct the comment for NAVI10_PCIE__LC_L1_INACTIVITY_TBT_DEFAULT
as 0x0000000E stands for 400ms instead of 4ms.

Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/amdgpu/sdma4: set align mask to 255

commit e5df16d9428f5c6d2d0b1eff244d6c330ba9ef3a upstream.

The wptr needs to be incremented at at least 64 dword intervals,
use 256 to align with windows. This should fix potential hangs
with unaligned updates.

Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Aaron Liu <aaron.liu@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit e5df16d9428f5c6d2d0b1eff244d6c330ba9ef3a)
The path `drivers/gpu/drm/amd/amdgpu/sdma_v4_4_2.c` doesn't exist in
6.1.y, only modify the file that does exist.
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/client: Send hotplug event after registering a client

commit 27655b9bb9f0d9c32b8de8bec649b676898c52d5 upstream.

Generate a hotplug event after registering a client to allow the
client to configure its display. Remove the hotplug calls from the
existing clients for fbdev emulation. This change fixes a concurrency
bug between registering a client and receiving events from the DRM
core. The bug is present in the fbdev emulation of all drivers.

The fbdev emulation currently generates a hotplug event before
registering the client to the device. For each new output, the DRM
core sends an additional hotplug event to each registered client.

If the DRM core detects first output between sending the artificial
hotplug and registering the device, the output's hotplug event gets
lost. If this is the first output, the fbdev console display remains
dark. This has been observed with amdgpu and fbdev-generic.

Fix this by adding hotplug generation directly to the client's
register helper drm_client_register(). Registering the client and
receiving events are serialized by struct drm_device.clientlist_mutex.
So an output is either configured by the initial hotplug event, or
the client has already been registered.

The bug was originally added in commit 6e3f17ee73f7 ("drm/fb-helper:
generic: Call drm_client_add() after setup is done"), in which adding
a client and receiving a hotplug event switched order. It was hidden,
as most hardware and drivers have at least on static output configured.
Other drivers didn't use the internal DRM client or still had struct
drm_mode_config_funcs.output_poll_changed set. That callback handled
hotplug events as well. After not setting the callback in amdgpu in
commit 0e3172bac3f4 ("drm/amdgpu: Don't set struct
drm_driver.output_poll_changed"), amdgpu did not show a framebuffer
console if output events got lost. The bug got copy-pasted from
fbdev-generic into the other fbdev emulation.

Reported-by: Moritz Duge <MoritzDuge@kolahilft.de>
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/2649
Fixes: 6e3f17ee73f7 ("drm/fb-helper: generic: Call drm_client_add() after setup is done")
Fixes: 8ab59da26bc0 ("drm/fb-helper: Move generic fbdev emulation into separate source file")
Fixes: b79fe9abd58b ("drm/fbdev-dma: Implement fbdev emulation for GEM DMA helpers")
Fixes: 63c381552f69 ("drm/armada: Implement fbdev emulation as in-kernel client")
Fixes: 49953b70e7d3 ("drm/exynos: Implement fbdev emulation as in-kernel client")
Fixes: 8f1aaccb04b7 ("drm/gma500: Implement client-based fbdev emulation")
Fixes: 940b869c2f2f ("drm/msm: Implement fbdev emulation as in-kernel client")
Fixes: 9e69bcd88e45 ("drm/omapdrm: Implement fbdev emulation as in-kernel client")
Fixes: e317a69fe891 ("drm/radeon: Implement client-based fbdev emulation")
Fixes: 71ec16f45ef8 ("drm/tegra: Implement fbdev emulation as in-kernel client")
Fixes: 0e3172bac3f4 ("drm/amdgpu: Don't set struct drm_driver.output_poll_changed")
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Tested-by: Moritz Duge <MoritzDuge@kolahilft.de>
Tested-by: Torsten Krah <krah.tm@gmail.com>
Tested-by: Paul Schyska <pschyska@gmail.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: David Airlie <airlied@gmail.com>
Cc: Noralf Trønnes <noralf@tronnes.org>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Javier Martinez Canillas <javierm@redhat.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Inki Dae <inki.dae@samsung.com>
Cc: Seung-Woo Kim <sw0312.kim@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Cc: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Cc: Rob Clark <robdclark@gmail.com>
Cc: Abhinav Kumar <quic_abhinavk@quicinc.com>
Cc: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Cc: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: "Pan, Xinhui" <Xinhui.Pan@amd.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Mikko Perttunen <mperttunen@nvidia.com>
Cc: dri-devel@lists.freedesktop.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-samsung-soc@vger.kernel.org
Cc: linux-arm-msm@vger.kernel.org
Cc: freedreno@lists.freedesktop.org
Cc: amd-gfx@lists.freedesktop.org
Cc: linux-tegra@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Cc: <stable@vger.kernel.org> # v5.2+
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> # msm
Link: https://patchwork.freedesktop.org/patch/msgid/20230710091029.27503-1-tzimmermann@suse.de
(cherry picked from commit 27655b9bb9f0d9c32b8de8bec649b676898c52d5)
[ Dropped changes to drivers/gpu/drm/armada/armada_fbdev.c as
  174c3c38e3a2 drm/armada: Initialize fbdev DRM client
  was introduced in 6.5-rc1.

  Dropped changes to exynos, msm, omapdrm, radeon, tegra drivers
  as missing code these commits introduced:

  99286486d674 drm/exynos: Initialize fbdev DRM client
  841ef552b141 drm/msm: Initialize fbdev DRM client
  9e69bcd88e45 drm/omapdrm: Implement fbdev emulation as in-kernel client
  e317a69fe891 drm/radeon: Implement client-based fbdev emulation
  9b926bcf2636 drm/radeon: Only build fbdev if DRM_FBDEV_EMULATION is set
  25dda38e0b07 drm/tegra: Initialize fbdev DRM client
  8f1aaccb04b7 drm/gma500: Implement client-based fbdev emulation
  b79fe9abd58b drm/fbdev-dma: Implement fbdev emulation for GEM DMA helpers

  Move code for drm-fbdev-generic.c to matching file in 6.1.y because
  these commits haven't happened in 6.1.y.
  8ab59da26bc0 drm/fb-helper: Move generic fbdev emulation into separate source file
  b9c93f4ec737 drm/fbdev-generic: Rename symbols ]
Cc: alexandru.gagniuc@hp.com
Link: https://lore.kernel.org/stable/SJ0PR84MB20882EEA1ABB36F60E845E378F5AA@SJ0PR84MB2088.NAMPRD84.PROD.OUTLOOK.COM/
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

cifs: fix session state check in smb2_find_smb_ses

commit 66be5c48ee1b5b8c919cc329fe6d32e16badaa40 upstream.

Chech the session state and skip it if it's exiting.

Signed-off-by: Winston Wen <wentao@uniontech.com>
Reviewed-by: Shyam Prasad N <sprasad@microsoft.com>
Cc: stable@vger.kernel.org
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ovl: fix null pointer dereference in ovl_get_acl_rcu()

[ Upstream commit f4e19e595cc2e76a8a58413eb19d3d9c51328b53 ]

Following process:
         P1                     P2
path_openat
  link_path_walk
   may_lookup
    inode_permission(rcu)
     ovl_permission
      acl_permission_check
       check_acl
        get_cached_acl_rcu
ovl_get_inode_acl
  realinode = ovl_inode_real(ovl_inode)
                      drop_cache
               __dentry_kill(ovl_dentry)
iput(ovl_inode)
                 ovl_destroy_inode(ovl_inode)
                  dput(oi->__upperdentry)
                   dentry_kill(upperdentry)
                    dentry_unlink_inode
     upperdentry->d_inode = NULL
    ovl_inode_upper
     upperdentry = ovl_i_dentry_upper(ovl_inode)
     d_inode(upperdentry) // returns NULL
  IS_POSIXACL(realinode) // NULL pointer dereference
, will trigger an null pointer dereference at realinode:
  [  205.472797] BUG: kernel NULL pointer dereference, address:
                 0000000000000028
  [  205.476701] CPU: 2 PID: 2713 Comm: ls Not tainted
                 6.3.0-12064-g2edfa098e750-dirty #1216
  [  205.478754] RIP: 0010:do_ovl_get_acl+0x5d/0x300
  [  205.489584] Call Trace:
  [  205.489812]  <TASK>
  [  205.490014]  ovl_get_inode_acl+0x26/0x30
  [  205.490466]  get_cached_acl_rcu+0x61/0xa0
  [  205.490908]  generic_permission+0x1bf/0x4e0
  [  205.491447]  ovl_permission+0x79/0x1b0
  [  205.491917]  inode_permission+0x15e/0x2c0
  [  205.492425]  link_path_walk+0x115/0x550
  [  205.493311]  path_lookupat.isra.0+0xb2/0x200
  [  205.493803]  filename_lookup+0xda/0x240
  [  205.495747]  vfs_fstatat+0x7b/0xb0

Fetch a reproducer in [Link].

Use the helper ovl_i_path_realinode() to get realinode and then do
non-nullptr checking.

There are some changes from upstream commit:
1. Corrusponds to do_ovl_get_acl() in 6.1 is ovl_get_acl()
2. Context conflicts caused by 6c0a8bfb84af8f3 ("ovl: implement get acl
   method") is handled.

Link: https://bugzilla.kernel.org/show_bug.cgi?id=217404
Fixes: 332f606b32b6 ("ovl: enable RCU'd ->get_acl()")
Cc: <stable@vger.kernel.org> # v5.15
Signed-off-by: Zhihao Cheng <chengzhihao1@huawei.com>
Suggested-by: Christian Brauner <brauner@kernel.org>
Suggested-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ovl: let helper ovl_i_path_real() return the realinode

[ Upstream commit b2dd05f107b11966e26fe52a313b418364cf497b ]

Let helper ovl_i_path_real() return the realinode to prepare for
checking non-null realinode in RCU walking path.

[msz] Use d_inode_rcu() since we are depending on the consitency
between dentry and inode being non-NULL in an RCU setting.

There are some changes from upstream commit:
1. Context conflicts caused by 73db6a063c785bc ("ovl: port to
vfs{g,u}id_t and associated helpers") is handled.

Signed-off-by: Zhihao Cheng <chengzhihao1@huawei.com>
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Fixes: ffa5723c6d25 ("ovl: store lower path in ovl_inode")
Cc: <stable@vger.kernel.org> # v5.19
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

fs/ntfs3: Check fields while reading

commit 0e8235d28f3a0e9eda9f02ff67ee566d5f42b66b upstream.

Added new functions index_hdr_check and index_buf_check.
Now we check all stuff for correctness while reading from disk.
Also fixed bug with stale nfs data.

Reported-by: van fantasy <g1042620637@gmail.com>
Signed-off-by: Konstantin Komarov <almaz.alexandrovich@paragon-software.com>
Fixes: 82cae269cfa95 ("fs/ntfs3: Add initialization of super block")
Signed-off-by: Lee Jones <lee@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

nvme-pci: fix DMA direction of unmapping integrity data

[ Upstream commit b8f6446b6853768cb99e7c201bddce69ca60c15e ]

DMA direction should be taken in dma_unmap_page() for unmapping integrity
data.

Fix this DMA direction, and reported in Guangwu's test.

Reported-by: Guangwu Zhang <guazhang@redhat.com>
Fixes: 4aedb705437f ("nvme-pci: split metadata handling from nvme_map_data / nvme_unmap_data")
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net/sched: sch_qfq: account for stab overhead in qfq_enqueue

[ Upstream commit 3e337087c3b5805fe0b8a46ba622a962880b5d64 ]

Lion says:
-------
In the QFQ scheduler a similar issue to CVE-2023-31436
persists.

Consider the following code in net/sched/sch_qfq.c:

static int qfq_enqueue(struct sk_buff *skb, struct Qdisc *sch,
                struct sk_buff **to_free)
{
     unsigned int len = qdisc_pkt_len(skb), gso_segs;

    // ...

     if (unlikely(cl->agg->lmax < len)) {
         pr_debug("qfq: increasing maxpkt from %u to %u for class %u",
              cl->agg->lmax, len, cl->common.classid);
         err = qfq_change_agg(sch, cl, cl->agg->class_weight, len);
         if (err) {
             cl->qstats.drops++;
             return qdisc_drop(skb, sch, to_free);
         }

    // ...

     }

Similarly to CVE-2023-31436, "lmax" is increased without any bounds
checks according to the packet length "len". Usually this would not
impose a problem because packet sizes are naturally limited.

This is however not the actual packet length, rather the
"qdisc_pkt_len(skb)" which might apply size transformations according to
"struct qdisc_size_table" as created by "qdisc_get_stab()" in
net/sched/sch_api.c if the TCA_STAB option was set when modifying the qdisc.

A user may choose virtually any size using such a table.

As a result the same issue as in CVE-2023-31436 can occur, allowing heap
out-of-bounds read / writes in the kmalloc-8192 cache.
-------

We can create the issue with the following commands:

tc qdisc add dev $DEV root handle 1: stab mtu 2048 tsize 512 mpu 0 \
overhead 999999999 linklayer ethernet qfq
tc class add dev $DEV parent 1: classid 1:1 htb rate 6mbit burst 15k
tc filter add dev $DEV parent 1: matchall classid 1:1
ping -I $DEV 1.1.1.2

This is caused by incorrectly assuming that qdisc_pkt_len() returns a
length within the QFQ_MIN_LMAX < len < QFQ_MAX_LMAX.

Fixes: 462dbc9101ac ("pkt_sched: QFQ Plus: fair-queueing service at DRR cost")
Reported-by: Lion <nnamrec@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Pedro Tammela <pctammela@mojatatu.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net/sched: sch_qfq: refactor parsing of netlink parameters

[ Upstream commit 25369891fcef373540f8b4e0b3bccf77a04490d5 ]

Two parameters can be transformed into netlink policies and
validated while parsing the netlink message.

Reviewed-by: Simon Horman <simon.horman@corigine.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Pedro Tammela <pctammela@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: 3e337087c3b5 ("net/sched: sch_qfq: account for stab overhead in qfq_enqueue")
Signed-off-by: Sasha Levin <sashal@kernel.org>

wifi: rtw89: debug: fix error code in rtw89_debug_priv_send_h2c_set()

[ Upstream commit 4f4626cd049576af1276c7568d5b44eb3f7bb1b1 ]

If there is a failure during rtw89_fw_h2c_raw() rtw89_debug_priv_send_h2c
should return negative error code instead of a positive value count.
Fix this bug by returning correct error code.

Fixes: e3ec7017f6a2 ("rtw89: add Realtek 802.11ax driver")
Signed-off-by: Zhang Shurong <zhang_shurong@foxmail.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://lore.kernel.org/r/tencent_AD09A61BC4DA92AD1EB0790F5C850E544D07@qq.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net/sched: make psched_mtu() RTNL-less safe

[ Upstream commit 150e33e62c1fa4af5aaab02776b6c3812711d478 ]

Eric Dumazet says[1]:
-------
Speaking of psched_mtu(), I see that net/sched/sch_pie.c is using it
without holding RTNL, so dev->mtu can be changed underneath.
KCSAN could issue a warning.
-------

Annotate dev->mtu with READ_ONCE() so KCSAN don't issue a warning.

[1] https://lore.kernel.org/all/CANn89iJoJO5VtaJ-2=_d2aOQhb0Xw8iBT_Cxqp2HyuS-zj6azw@mail.gmail.com/

v1 -> v2: Fix commit message

Fixes: d4b36210c2e6 ("net: pkt_sched: PIE AQM scheme")
Suggested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Pedro Tammela <pctammela@mojatatu.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230711021634.561598-1-pctammela@mojatatu.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

netdevsim: fix uninitialized data in nsim_dev_trap_fa_cookie_write()

[ Upstream commit f72207a5c0dbaaf6921cf9a6c0d2fd0bc249ea78 ]

The simple_write_to_buffer() function is designed to handle partial
writes.  It returns negatives on error, otherwise it returns the number
of bytes that were able to be copied.  This code doesn't check the
return properly.  We only know that the first byte is written, the rest
of the buffer might be uninitialized.

There is no need to use the simple_write_to_buffer() function.
Partial writes are prohibited by the "if (*ppos != 0)" check at the
start of the function.  Just use memdup_user() and copy the whole
buffer.

Fixes: d3cbb907ae57 ("netdevsim: add ACL trap reporting cookie as a metadata")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Link: https://lore.kernel.org/r/7c1f950b-3a7d-4252-82a6-876e53078ef7@moroto.mountain
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

riscv: mm: fix truncation warning on RV32

[ Upstream commit b690e266dae2f85f4dfea21fa6a05e3500a51054 ]

lkp reports below sparse warning when building for RV32:
arch/riscv/mm/init.c:1204:48: sparse: warning: cast truncates bits from
constant value (100000000 becomes 0)

IMO, the reason we didn't see this truncates bug in real world is "0"
means MEMBLOCK_ALLOC_ACCESSIBLE in memblock and there's no RV32 HW
with more than 4GB memory.

Fix it anyway to make sparse happy.

Fixes: decf89f86ecd ("riscv: try to allocate crashkern region from 32bit addressible memory")
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202306080034.SLiCiOMn-lkp@intel.com/
Link: https://lore.kernel.org/r/20230709171036.1906-1-jszhang@kernel.org
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net/sched: flower: Ensure both minimum and maximum ports are specified

[ Upstream commit d3f87278bcb80bd7f9519669d928b43320363d4f ]

The kernel does not currently validate that both the minimum and maximum
ports of a port range are specified. This can lead user space to think
that a filter matching on a port range was successfully added, when in
fact it was not. For example, with a patched (buggy) iproute2 that only
sends the minimum port, the following commands do not return an error:

# tc filter add dev swp1 ingress pref 1 proto ip flower ip_proto udp src_port 100-200 action pass

# tc filter add dev swp1 ingress pref 1 proto ip flower ip_proto udp dst_port 100-200 action pass

# tc filter show dev swp1 ingress
filter protocol ip pref 1 flower chain 0
filter protocol ip pref 1 flower chain 0 handle 0x1
   eth_type ipv4
   ip_proto udp
   not_in_hw
         action order 1: gact action pass
          random type none pass val 0
          index 1 ref 1 bind 1

filter protocol ip pref 1 flower chain 0 handle 0x2
   eth_type ipv4
   ip_proto udp
   not_in_hw
         action order 1: gact action pass
          random type none pass val 0
          index 2 ref 1 bind 1

Fix by returning an error unless both ports are specified:

# tc filter add dev swp1 ingress pref 1 proto ip flower ip_proto udp src_port 100-200 action pass
Error: Both min and max source ports must be specified.
We have an error talking to the kernel

# tc filter add dev swp1 ingress pref 1 proto ip flower ip_proto udp dst_port 100-200 action pass
Error: Both min and max destination ports must be specified.
We have an error talking to the kernel

Fixes: 5c72299fba9d ("net: sched: cls_flower: Classify packets using port ranges")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

bpf: cpumap: Fix memory leak in cpu_map_update_elem

[ Upstream commit 4369016497319a9635702da010d02af1ebb1849d ]

Syzkaller reported a memory leak as follows:

BUG: memory leak
unreferenced object 0xff110001198ef748 (size 192):
  comm "syz-executor.3", pid 17672, jiffies 4298118891 (age 9.906s)
  hex dump (first 32 bytes):
    00 00 00 00 4a 19 00 00 80 ad e3 e4 fe ff c0 00  ....J...........
    00 b2 d3 0c 01 00 11 ff 28 f5 8e 19 01 00 11 ff  ........(.......
  backtrace:
    [<ffffffffadd28087>] __cpu_map_entry_alloc+0xf7/0xb00
    [<ffffffffadd28d8e>] cpu_map_update_elem+0x2fe/0x3d0
    [<ffffffffadc6d0fd>] bpf_map_update_value.isra.0+0x2bd/0x520
    [<ffffffffadc7349b>] map_update_elem+0x4cb/0x720
    [<ffffffffadc7d983>] __se_sys_bpf+0x8c3/0xb90
    [<ffffffffb029cc80>] do_syscall_64+0x30/0x40
    [<ffffffffb0400099>] entry_SYSCALL_64_after_hwframe+0x61/0xc6

BUG: memory leak
unreferenced object 0xff110001198ef528 (size 192):
  comm "syz-executor.3", pid 17672, jiffies 4298118891 (age 9.906s)
  hex dump (first 32 bytes):
    00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
    00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
  backtrace:
    [<ffffffffadd281f0>] __cpu_map_entry_alloc+0x260/0xb00
    [<ffffffffadd28d8e>] cpu_map_update_elem+0x2fe/0x3d0
    [<ffffffffadc6d0fd>] bpf_map_update_value.isra.0+0x2bd/0x520
    [<ffffffffadc7349b>] map_update_elem+0x4cb/0x720
    [<ffffffffadc7d983>] __se_sys_bpf+0x8c3/0xb90
    [<ffffffffb029cc80>] do_syscall_64+0x30/0x40
    [<ffffffffb0400099>] entry_SYSCALL_64_after_hwframe+0x61/0xc6

BUG: memory leak
unreferenced object 0xff1100010fd93d68 (size 8):
  comm "syz-executor.3", pid 17672, jiffies 4298118891 (age 9.906s)
  hex dump (first 8 bytes):
    00 00 00 00 00 00 00 00                          ........
  backtrace:
    [<ffffffffade5db3e>] kvmalloc_node+0x11e/0x170
    [<ffffffffadd28280>] __cpu_map_entry_alloc+0x2f0/0xb00
    [<ffffffffadd28d8e>] cpu_map_update_elem+0x2fe/0x3d0
    [<ffffffffadc6d0fd>] bpf_map_update_value.isra.0+0x2bd/0x520
    [<ffffffffadc7349b>] map_update_elem+0x4cb/0x720
    [<ffffffffadc7d983>] __se_sys_bpf+0x8c3/0xb90
    [<ffffffffb029cc80>] do_syscall_64+0x30/0x40
    [<ffffffffb0400099>] entry_SYSCALL_64_after_hwframe+0x61/0xc6

In the cpu_map_update_elem flow, when kthread_stop is called before
calling the threadfn of rcpu->kthread, since the KTHREAD_SHOULD_STOP bit
of kthread has been set by kthread_stop, the threadfn of rcpu->kthread
will never be executed, and rcpu->refcnt will never be 0, which will
lead to the allocated rcpu, rcpu->queue and rcpu->queue->queue cannot be
released.

Calling kthread_stop before executing kthread's threadfn will return
-EINTR. We can complete the release of memory resources in this state.

Fixes: 6710e1126934 ("bpf: introduce new bpf cpu map type BPF_MAP_TYPE_CPUMAP")
Signed-off-by: Pu Lehui <pulehui@huawei.com>
Acked-by: Jesper Dangaard Brouer <hawk@kernel.org>
Acked-by: Hou Tao <houtao1@huawei.com>
Link: https://lore.kernel.org/r/20230711115848.2701559-1-pulehui@huaweicloud.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

wifi: airo: avoid uninitialized warning in airo_get_rate()

[ Upstream commit 9373771aaed17f5c2c38485f785568abe3a9f8c1 ]

Quieten a gcc (11.3.0) build error or warning by checking the function
call status and returning -EBUSY if the function call failed.
This is similar to what several other wireless drivers do for the
SIOCGIWRATE ioctl call when there is a locking problem.

drivers/net/wireless/cisco/airo.c: error: 'status_rid.currentXmitRate' is used uninitialized [-Werror=uninitialized]

Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Link: https://lore.kernel.org/r/39abf2c7-24a-f167-91da-ed4c5435d1c4@linux-m68k.org
Link: https://lore.kernel.org/r/20230709133154.26206-1-rdunlap@infradead.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

erofs: fix fsdax unavailability for chunk-based regular files

[ Upstream commit 18bddc5b67038722cb88fcf51fbf41a0277092cb ]

DAX can be used to share page cache between VMs, reducing guest memory
overhead. And chunk based data format is widely used for VM and
container image. So enable dax support for it, make erofs better used
for VM scenarios.

Fixes: c5aa903a59db ("erofs: support reading chunk-based uncompressed files")
Signed-off-by: Xin Yin <yinxin.x@bytedance.com>
Reviewed-by: Gao Xiang <hsiangkao@linux.alibaba.com>
Reviewed-by: Chao Yu <chao@kernel.org>
Link: https://lore.kernel.org/r/20230711062130.7860-1-yinxin.x@bytedance.com
Signed-off-by: Gao Xiang <hsiangkao@linux.alibaba.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

erofs: avoid infinite loop in z_erofs_do_read_page() when reading beyond EOF

[ Upstream commit 8191213a5835b0317c5e4d0d337ae1ae00c75253 ]

z_erofs_do_read_page() may loop infinitely due to the inappropriate
truncation in the below statement. Since the offset is 64 bits and min_t()
truncates the result to 32 bits. The solution is to replace unsigned int
with a 64-bit type, such as erofs_off_t.
    cur = end - min_t(unsigned int, offset + end - map->m_la, end);

    - For example:
        - offset = 0x400160000
        - end = 0x370
        - map->m_la = 0x160370
        - offset + end - map->m_la = 0x400000000
        - offset + end - map->m_la = 0x00000000 (truncated as unsigned int)
    - Expected result:
        - cur = 0
    - Actual result:
        - cur = 0x370

Signed-off-by: Chunhai Guo <guochunhai@vivo.com>
Fixes: 3883a79abd02 ("staging: erofs: introduce VLE decompression support")
Reviewed-by: Gao Xiang <hsiangkao@linux.alibaba.com>
Reviewed-by: Chao Yu <chao@kernel.org>
Link: https://lore.kernel.org/r/20230710093410.44071-1-guochunhai@vivo.com
Signed-off-by: Gao Xiang <hsiangkao@linux.alibaba.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

erofs: avoid useless loops in z_erofs_pcluster_readmore() when reading beyond EOF

[ Upstream commit 936aa701d82d397c2d1afcd18ce2c739471d978d ]

z_erofs_pcluster_readmore() may take a long time to loop when the page
offset is large enough, which is unnecessary should be prevented.

For example, when the following case is encountered, it will loop 4691368
times, taking about 27 seconds:
- offset = 19217289215
- inode_size = 1442672

Signed-off-by: Chunhai Guo <guochunhai@vivo.com>
Fixes: 386292919c25 ("erofs: introduce readmore decompression strategy")
Reviewed-by: Gao Xiang <hsiangkao@linux.alibaba.com>
Reviewed-by: Yue Hu <huyue2@coolpad.com>
Reviewed-by: Chao Yu <chao@kernel.org>
Link: https://lore.kernel.org/r/20230710042531.28761-1-guochunhai@vivo.com
Signed-off-by: Gao Xiang <hsiangkao@linux.alibaba.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

octeontx2-pf: Add additional check for MCAM rules

[ Upstream commit 8278ee2a2646b9acf747317895e47a640ba933c9 ]

Due to hardware limitation, MCAM drop rule with
ether_type == 802.1Q and vlan_id == 0 is not supported. Hence rejecting
such rules.

Fixes: dce677da57c0 ("octeontx2-pf: Add vlan-etype to ntuple filters")
Signed-off-by: Suman Ghosh <sumang@marvell.com>
Link: https://lore.kernel.org/r/20230710103027.2244139-1-sumang@marvell.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/i915: Fix one wrong caching mode enum usage

[ Upstream commit 113899c2669dff148b2a5bea4780123811aecc13 ]

Commit a4d86249c773 ("drm/i915/gt: Provide a utility to create a scratch
buffer") mistakenly passed in uapi I915_CACHING_CACHED as argument to
i915_gem_object_set_cache_coherency(), which actually takes internal
enum i915_cache_level.

No functional issue since the value matches I915_CACHE_LLC (1 == 1), which
is the intended caching mode, but lets clean it up nevertheless.

Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Fixes: a4d86249c773 ("drm/i915/gt: Provide a utility to create a scratch buffer")
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Reviewed-by: Tejas Upadhyay <tejas.upadhyay@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230707125503.3965817-1-tvrtko.ursulin@linux.intel.com
(cherry picked from commit 49c60b2f0867ac36fd54d513882a48431aeccae7)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/i915: Don't preserve dpll_hw_state for slave crtc in Bigjoiner

[ Upstream commit 5c413188c68da0e4bffc93de1c80257e20741e69 ]

If we are using Bigjoiner dpll_hw_state is supposed to be exactly
same as for master crtc, so no need to save it's state for slave crtc.

Signed-off-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Fixes: 0ff0e219d9b8 ("drm/i915: Compute clocks earlier")
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230628141017.18937-1-stanislav.lisovskiy@intel.com
(cherry picked from commit cbaf758809952c95ec00e796695049babb08bb60)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

riscv, bpf: Fix inconsistent JIT image generation

[ Upstream commit c56fb2aab23505bb7160d06097c8de100b82b851 ]

In order to generate the prologue and epilogue, the BPF JIT needs to
know which registers that are clobbered. Therefore, the during
pre-final passes, the prologue is generated after the body of the
program body-prologue-epilogue. Then, in the final pass, a proper
prologue-body-epilogue JITted image is generated.

This scheme has worked most of the time. However, for some large
programs with many jumps, e.g. the test_kmod.sh BPF selftest with
hardening enabled (blinding constants), this has shown to be
incorrect. For the final pass, when the proper prologue-body-epilogue
is generated, the image has not converged. This will lead to that the
final image will have incorrect jump offsets. The following is an
excerpt from an incorrect image:

  | ...
  |     3b8:       00c50663                beq     a0,a2,3c4 <.text+0x3c4>
  |     3bc:       0020e317                auipc   t1,0x20e
  |     3c0:       49630067                jalr    zero,1174(t1) # 20e852 <.text+0x20e852>
  | ...
  |  20e84c:       8796                    c.mv    a5,t0
  |  20e84e:       6422                    c.ldsp  s0,8(sp)    # Epilogue start
  |  20e850:       6141                    c.addi16sp      sp,16
  |  20e852:       853e                    c.mv    a0,a5       # Incorrect jump target
  |  20e854:       8082                    c.jr    ra

The image has shrunk, and the epilogue offset is incorrect in the
final pass.

Correct the problem by always generating proper prologue-body-epilogue
outputs, which means that the first pass will only generate the body
to track what registers that are touched.

Fixes: 2353ecc6f91f ("bpf, riscv: add BPF JIT for RV64G")
Signed-off-by: Björn Töpel <bjorn@rivosinc.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20230710074131.19596-1-bjorn@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>

nvme: fix the NVME_ID_NS_NVM_STS_MASK definition

[ Upstream commit b938e6603660652dc3db66d3c915fbfed3bce21d ]

As per NVMe command set specification 1.0c Storage tag size is 7 bits.

Fixes: 4020aad85c67 ("nvme: add support for enhanced metadata")
Signed-off-by: Ankit Kumar <ankit.kumar@samsung.com>
Reviewed-by: Kanchan Joshi <joshi.k@samsung.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

igc: Fix inserting of empty frame for launchtime

[ Upstream commit 0bcc62858d6ba62cbade957d69745e6adeed5f3d ]

The insertion of an empty frame was introduced with
commit db0b124f02ba ("igc: Enhance Qbv scheduling by using first flag bit")
in order to ensure that the current cycle has at least one packet if
there is some packet to be scheduled for the next cycle.

However, the current implementation does not properly check if
a packet is already scheduled for the current cycle. Currently,
an empty packet is always inserted if and only if
txtime >= end_of_cycle && txtime > last_tx_cycle
but since last_tx_cycle is always either the end of the current
cycle (end_of_cycle) or the end of a previous cycle, the
second part (txtime > last_tx_cycle) is always true unless
txtime == last_tx_cycle.

What actually needs to be checked here is if the last_tx_cycle
was already written within the current cycle, so an empty frame
should only be inserted if and only if
txtime >= end_of_cycle && end_of_cycle > last_tx_cycle.

This patch does not only avoid an unnecessary insertion, but it
can actually be harmful to insert an empty packet if packets
are already scheduled in the current cycle, because it can lead
to a situation where the empty packet is actually processed
as the first packet in the upcoming cycle shifting the packet
with the first_flag even one cycle into the future, finally leading
to a TX hang.

The TX hang can be reproduced on a i225 with:

    sudo tc qdisc replace dev enp1s0 parent root handle 100 taprio \
    num_tc 1 \
    map 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 \
    queues 1@0 \
    base-time 0 \
    sched-entry S 01 300000 \
    flags 0x1 \
    txtime-delay 500000 \
    clockid CLOCK_TAI
    sudo tc qdisc replace dev enp1s0 parent 100:1 etf \
    clockid CLOCK_TAI \
    delta 500000 \
    offload \
    skip_sock_check

and traffic generator

    sudo trafgen -i traffic.cfg -o enp1s0 --cpp -n0 -q -t1400ns

with traffic.cfg

    #define ETH_P_IP        0x0800

    {
      /* Ethernet Header */
      0x30, 0x1f, 0x9a, 0xd0, 0xf0, 0x0e,  # MAC Dest - adapt as needed
      0x24, 0x5e, 0xbe, 0x57, 0x2e, 0x36,  # MAC Src  - adapt as needed
      const16(ETH_P_IP),

      /* IPv4 Header */
      0b01000101, 0,   # IPv4 version, IHL, TOS
      const16(1028),   # IPv4 total length (UDP length + 20 bytes (IP header))
      const16(2),      # IPv4 ident
      0b01000000, 0,   # IPv4 flags, fragmentation off
      64,              # IPv4 TTL
      17,              # Protocol UDP
      csumip(14, 33),  # IPv4 checksum

      /* UDP Header */
      10,  0, 48, 1,   # IP Src - adapt as needed
      10,  0, 48, 10,  # IP Dest - adapt as needed
      const16(5555),   # UDP Src Port
      const16(6666),   # UDP Dest Port
      const16(1008),   # UDP length (UDP header 8 bytes + payload length)
      csumudp(14, 34), # UDP checksum

      /* Payload */
      fill('W', 1000),
    }

and the observed message with that is for example

igc 0000:01:00.0 enp1s0: Detected Tx Unit Hang
   Tx Queue             <0>
   TDH                  <32>
   TDT                  <3c>
   next_to_use          <3c>
   next_to_clean        <32>
buffer_info[next_to_clean]
   time_stamp           <ffff26a8>
   next_to_watch        <00000000632a1828>
   jiffies              <ffff27f8>
   desc.status          <1048000>

Fixes: db0b124f02ba ("igc: Enhance Qbv scheduling by using first flag bit")
Signed-off-by: Florian Kauer <florian.kauer@linutronix.de>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

igc: Fix launchtime before start of cycle

[ Upstream commit c1bca9ac0bcb355be11354c2e68bc7bf31f5ac5a ]

It is possible (verified on a running system) that frames are processed
by igc_tx_launchtime with a txtime before the start of the cycle
(baset_est).

However, the result of txtime - baset_est is written into a u32,
leading to a wrap around to a positive number. The following
launchtime > 0 check will only branch to executing launchtime = 0
if launchtime is already 0.

Fix it by using a s32 before checking launchtime > 0.

Fixes: db0b124f02ba ("igc: Enhance Qbv scheduling by using first flag bit")
Signed-off-by: Florian Kauer <florian.kauer@linutronix.de>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

kernel/trace: Fix cleanup logic of enable_trace_eprobe

[ Upstream commit cf0a624dc706c306294c14e6b3e7694702f25191 ]

The enable_trace_eprobe() function enables all event probes, attached
to given trace probe. If an error occurs in enabling one of the event
probes, all others should be roll backed. There is a bug in that roll
back logic - instead of all event probes, only the failed one is
disabled.

Link: https://lore.kernel.org/all/20230703042853.1427493-1-tz.stoyanov@gmail.com/
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Fixes: 7491e2c44278 ("tracing: Add a probe that attaches to trace events")
Signed-off-by: Tzvetomir Stoyanov (VMware) <tz.stoyanov@gmail.com>
Acked-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Reviewed-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

platform/x86: wmi: Break possible infinite loop when parsing GUID

[ Upstream commit 028e6e204ace1f080cfeacd72c50397eb8ae8883 ]

The while-loop may break on one of the two conditions, either ID string
is empty or GUID matches. The second one, may never be reached if the
parsed string is not correct GUID. In such a case the loop will never
advance to check the next ID.

Break possible infinite loop by factoring out guid_parse_and_compare()
helper which may be moved to the generic header for everyone later on
and preventing from similar mistake in the future.

Interestingly that firstly it appeared when WMI was turned into a bus
driver, but later when duplicated GUIDs were checked, the while-loop
has been replaced by for-loop and hence no mistake made again.

Fixes: a48e23385fcf ("platform/x86: wmi: add context pointer field to struct wmi_device_id")
Fixes: 844af950da94 ("platform/x86: wmi: Turn WMI into a bus driver")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230621151155.78279-1-andriy.shevchenko@linux.intel.com
Tested-by: Armin Wolf <W_Armin@gmx.de>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: dsa: qca8k: Add check for skb_copy

[ Upstream commit 87355b7c3da9bfd81935caba0ab763355147f7b0 ]

Add check for the return value of skb_copy in order to avoid NULL pointer
dereference.

Fixes: 2cd548566384 ("net: dsa: qca8k: add support for phy read/write with mgmt Ethernet")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ipv6/addrconf: fix a potential refcount underflow for idev

[ Upstream commit 06a0716949c22e2aefb648526580671197151acc ]

Now in addrconf_mod_rs_timer(), reference idev depends on whether
rs_timer is not pending. Then modify rs_timer timeout.

There is a time gap in [1], during which if the pending rs_timer
becomes not pending. It will miss to hold idev, but the rs_timer
is activated. Thus rs_timer callback function addrconf_rs_timer()
will be executed and put idev later without holding idev. A refcount
underflow issue for idev can be caused by this.

if (!timer_pending(&idev->rs_timer))
in6_dev_hold(idev);
<--------------[1]
mod_timer(&idev->rs_timer, jiffies + when);

To fix the issue, hold idev if mod_timer() return 0.

Fixes: b7b1bfce0bb6 ("ipv6: split duplicate address detection and router solicitation timer")
Suggested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

NTB: ntb_tool: Add check for devm_kcalloc

[ Upstream commit 2790143f09938776a3b4f69685b380bae8fd06c7 ]

As the devm_kcalloc may return NULL pointer,
it should be better to add check for the return
value, as same as the others.

Fixes: 7f46c8b3a552 ("NTB: ntb_tool: Add full multi-port NTB API support")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: Sasha Levin <sashal@kernel.org>

NTB: ntb_transport: fix possible memory leak while device_register() fails

[ Upstream commit 8623ccbfc55d962e19a3537652803676ad7acb90 ]

If device_register() returns error, the name allocated by
dev_set_name() need be freed. As comment of device_register()
says, it should use put_device() to give up the reference in
the error path. So fix this by calling put_device(), then the
name can be freed in kobject_cleanup(), and client_dev is freed
in ntb_transport_client_release().

Fixes: fce8a7bb5b4b ("PCI-Express Non-Transparent Bridge Support")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ntb: intel: Fix error handling in intel_ntb_pci_driver_init()

[ Upstream commit 4c3c796aca02883ad35bb117468938cc4022ca41 ]

A problem about ntb_hw_intel create debugfs failed is triggered with the
following log given:

[  273.112733] Intel(R) PCI-E Non-Transparent Bridge Driver 2.0
[  273.115342] debugfs: Directory 'ntb_hw_intel' with parent '/' already present!

The reason is that intel_ntb_pci_driver_init() returns
pci_register_driver() directly without checking its return value, if
pci_register_driver() failed, it returns without destroy the newly created
debugfs, resulting the debugfs of ntb_hw_intel can never be created later.

intel_ntb_pci_driver_init()
   debugfs_create_dir() # create debugfs directory
   pci_register_driver()
     driver_register()
       bus_add_driver()
         priv = kzalloc(...) # OOM happened
   # return without destroy debugfs directory

Fix by removing debugfs when pci_register_driver() returns error.

Fixes: e26a5843f7f5 ("NTB: Split ntb_hw_intel and ntb_transport drivers")
Signed-off-by: Yuan Can <yuancan@huawei.com>
Acked-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: Sasha Levin <sashal@kernel.org>

NTB: amd: Fix error handling in amd_ntb_pci_driver_init()

[ Upstream commit 98af0a33c1101c29b3ce4f0cf4715fd927c717f9 ]

A problem about ntb_hw_amd create debugfs failed is triggered with the
following log given:

[  618.431232] AMD(R) PCI-E Non-Transparent Bridge Driver 1.0
[  618.433284] debugfs: Directory 'ntb_hw_amd' with parent '/' already present!

The reason is that amd_ntb_pci_driver_init() returns pci_register_driver()
directly without checking its return value, if pci_register_driver()
failed, it returns without destroy the newly created debugfs, resulting
the debugfs of ntb_hw_amd can never be created later.

amd_ntb_pci_driver_init()
   debugfs_create_dir() # create debugfs directory
   pci_register_driver()
     driver_register()
       bus_add_driver()
         priv = kzalloc(...) # OOM happened
   # return without destroy debugfs directory

Fix by removing debugfs when pci_register_driver() returns error.

Fixes: a1b3695820aa ("NTB: Add support for AMD PCI-Express Non-Transparent Bridge")
Signed-off-by: Yuan Can <yuancan@huawei.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ntb: idt: Fix error handling in idt_pci_driver_init()

[ Upstream commit c012968259b451dc4db407f2310fe131eaefd800 ]

A problem about ntb_hw_idt create debugfs failed is triggered with the
following log given:

[ 1236.637636] IDT PCI-E Non-Transparent Bridge Driver 2.0
[ 1236.639292] debugfs: Directory 'ntb_hw_idt' with parent '/' already present!

The reason is that idt_pci_driver_init() returns pci_register_driver()
directly without checking its return value, if pci_register_driver()
failed, it returns without destroy the newly created debugfs, resulting
the debugfs of ntb_hw_idt can never be created later.

idt_pci_driver_init()
   debugfs_create_dir() # create debugfs directory
   pci_register_driver()
     driver_register()
       bus_add_driver()
         priv = kzalloc(...) # OOM happened
   # return without destroy debugfs directory

Fix by removing debugfs when pci_register_driver() returns error.

Fixes: bf2a952d31d2 ("NTB: Add IDT 89HPESxNTx PCIe-switches support")
Signed-off-by: Yuan Can <yuancan@huawei.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: Sasha Levin <sashal@kernel.org>

udp6: fix udp6_ehashfn() typo

[ Upstream commit 51d03e2f2203e76ed02d33fb5ffbb5fc85ffaf54 ]

Amit Klein reported that udp6_ehash_secret was initialized but never used.

Fixes: 1bbdceef1e53 ("inet: convert inet_ehash_secret and ipv6_hash_secret to net_get_random_once")
Reported-by: Amit Klein <aksecurity@gmail.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Willy Tarreau <w@1wt.eu>
Cc: Willem de Bruijn <willemdebruijn.kernel@gmail.com>
Cc: David Ahern <dsahern@kernel.org>
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

icmp6: Fix null-ptr-deref of ip6_null_entry->rt6i_idev in icmp6_dev().

[ Upstream commit 2aaa8a15de73874847d62eb595c6683bface80fd ]

With some IPv6 Ext Hdr (RPL, SRv6, etc.), we can send a packet that
has the link-local address as src and dst IP and will be forwarded to
an external IP in the IPv6 Ext Hdr.

For example, the script below generates a packet whose src IP is the
link-local address and dst is updated to 11::.

  # for f in $(find /proc/sys/net/ -name *seg6_enabled*); do echo 1 > $f; done
  # python3
  >>> from socket import *
  >>> from scapy.all import *
  >>>
  >>> SRC_ADDR = DST_ADDR = "fe80::5054:ff:fe12:3456"
  >>>
  >>> pkt = IPv6(src=SRC_ADDR, dst=DST_ADDR)
  >>> pkt /= IPv6ExtHdrSegmentRouting(type=4, addresses=["11::", "22::"], segleft=1)
  >>>
  >>> sk = socket(AF_INET6, SOCK_RAW, IPPROTO_RAW)
  >>> sk.sendto(bytes(pkt), (DST_ADDR, 0))

For such a packet, we call ip6_route_input() to look up a route for the
next destination in these three functions depending on the header type.

  * ipv6_rthdr_rcv()
  * ipv6_rpl_srh_rcv()
  * ipv6_srh_rcv()

If no route is found, ip6_null_entry is set to skb, and the following
dst_input(skb) calls ip6_pkt_drop().

Finally, in icmp6_dev(), we dereference skb_rt6_info(skb)->rt6i_idev->dev
as the input device is the loopback interface.  Then, we have to check if
skb_rt6_info(skb)->rt6i_idev is NULL or not to avoid NULL pointer deref
for ip6_null_entry.

BUG: kernel NULL pointer dereference, address: 0000000000000000
PF: supervisor read access in kernel mode
PF: error_code(0x0000) - not-present page
PGD 0 P4D 0
Oops: 0000 [#1] PREEMPT SMP PTI
CPU: 0 PID: 157 Comm: python3 Not tainted 6.4.0-11996-gb121d614371c #35
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.16.0-0-gd239552ce722-prebuilt.qemu.org 04/01/2014
RIP: 0010:icmp6_send (net/ipv6/icmp.c:436 net/ipv6/icmp.c:503)
Code: fe ff ff 48 c7 40 30 c0 86 5d 83 e8 c6 44 1c 00 e9 c8 fc ff ff 49 8b 46 58 48 83 e0 fe 0f 84 4a fb ff ff 48 8b 80 d0 00 00 00 <48> 8b 00 44 8b 88 e0 00 00 00 e9 34 fb ff ff 4d 85 ed 0f 85 69 01
RSP: 0018:ffffc90000003c70 EFLAGS: 00000286
RAX: 0000000000000000 RBX: 0000000000000001 RCX: 00000000000000e0
RDX: 0000000000000021 RSI: 0000000000000000 RDI: ffff888006d72a18
RBP: ffffc90000003d80 R08: 0000000000000000 R09: 0000000000000001
R10: ffffc90000003d98 R11: 0000000000000040 R12: ffff888006d72a10
R13: 0000000000000000 R14: ffff8880057fb800 R15: ffffffff835d86c0
FS:  00007f9dc72ee740(0000) GS:ffff88807dc00000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000000 CR3: 00000000057b2000 CR4: 00000000007506f0
PKRU: 55555554
Call Trace:
<IRQ>
ip6_pkt_drop (net/ipv6/route.c:4513)
ipv6_rthdr_rcv (net/ipv6/exthdrs.c:640 net/ipv6/exthdrs.c:686)
ip6_protocol_deliver_rcu (net/ipv6/ip6_input.c:437 (discriminator 5))
ip6_input_finish (./include/linux/rcupdate.h:781 net/ipv6/ip6_input.c:483)
__netif_receive_skb_one_core (net/core/dev.c:5455)
process_backlog (./include/linux/rcupdate.h:781 net/core/dev.c:5895)
__napi_poll (net/core/dev.c:6460)
net_rx_action (net/core/dev.c:6529 net/core/dev.c:6660)
__do_softirq (./arch/x86/include/asm/jump_label.h:27 ./include/linux/jump_label.h:207 ./include/trace/events/irq.h:142 kernel/softirq.c:554)
do_softirq (kernel/softirq.c:454 kernel/softirq.c:441)
</IRQ>
<TASK>
__local_bh_enable_ip (kernel/softirq.c:381)
__dev_queue_xmit (net/core/dev.c:4231)
ip6_finish_output2 (./include/net/neighbour.h:544 net/ipv6/ip6_output.c:135)
rawv6_sendmsg (./include/net/dst.h:458 ./include/linux/netfilter.h:303 net/ipv6/raw.c:656 net/ipv6/raw.c:914)
sock_sendmsg (net/socket.c:725 net/socket.c:748)
__sys_sendto (net/socket.c:2134)
__x64_sys_sendto (net/socket.c:2146 net/socket.c:2142 net/socket.c:2142)
do_syscall_64 (arch/x86/entry/common.c:50 arch/x86/entry/common.c:80)
entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:120)
RIP: 0033:0x7f9dc751baea
Code: d8 64 89 02 48 c7 c0 ff ff ff ff eb b8 0f 1f 00 f3 0f 1e fa 41 89 ca 64 8b 04 25 18 00 00 00 85 c0 75 15 b8 2c 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 7e c3 0f 1f 44 00 00 41 54 48 83 ec 30 44 89
RSP: 002b:00007ffe98712c38 EFLAGS: 00000246 ORIG_RAX: 000000000000002c
RAX: ffffffffffffffda RBX: 00007ffe98712cf8 RCX: 00007f9dc751baea
RDX: 0000000000000060 RSI: 00007f9dc6460b90 RDI: 0000000000000003
RBP: 00007f9dc56e8be0 R08: 00007ffe98712d70 R09: 000000000000001c
R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000000
R13: ffffffffc4653600 R14: 0000000000000001 R15: 00007f9dc6af5d1b
</TASK>
Modules linked in:
CR2: 0000000000000000
---[ end trace 0000000000000000 ]---
RIP: 0010:icmp6_send (net/ipv6/icmp.c:436 net/ipv6/icmp.c:503)
Code: fe ff ff 48 c7 40 30 c0 86 5d 83 e8 c6 44 1c 00 e9 c8 fc ff ff 49 8b 46 58 48 83 e0 fe 0f 84 4a fb ff ff 48 8b 80 d0 00 00 00 <48> 8b 00 44 8b 88 e0 00 00 00 e9 34 fb ff ff 4d 85 ed 0f 85 69 01
RSP: 0018:ffffc90000003c70 EFLAGS: 00000286
RAX: 0000000000000000 RBX: 0000000000000001 RCX: 00000000000000e0
RDX: 0000000000000021 RSI: 0000000000000000 RDI: ffff888006d72a18
RBP: ffffc90000003d80 R08: 0000000000000000 R09: 0000000000000001
R10: ffffc90000003d98 R11: 0000000000000040 R12: ffff888006d72a10
R13: 0000000000000000 R14: ffff8880057fb800 R15: ffffffff835d86c0
FS:  00007f9dc72ee740(0000) GS:ffff88807dc00000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000000 CR3: 00000000057b2000 CR4: 00000000007506f0
PKRU: 55555554
Kernel panic - not syncing: Fatal exception in interrupt
Kernel Offset: disabled

Fixes: 4832c30d5458 ("net: ipv6: put host and anycast routes on device with address")
Reported-by: Wang Yufen <wangyufen@huawei.com>
Closes: https://lore.kernel.org/netdev/c41403a9-c2f6-3b7e-0c96-e1901e605cd0@huawei.com/
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: prevent skb corruption on frag list segmentation

[ Upstream commit c329b261afe71197d9da83c1f18eb45a7e97e089 ]

Ian reported several skb corruptions triggered by rx-gro-list,
collecting different oops alike:

[   62.624003] BUG: kernel NULL pointer dereference, address: 00000000000000c0
[   62.631083] #PF: supervisor read access in kernel mode
[   62.636312] #PF: error_code(0x0000) - not-present page
[   62.641541] PGD 0 P4D 0
[   62.644174] Oops: 0000 [#1] PREEMPT SMP NOPTI
[   62.648629] CPU: 1 PID: 913 Comm: napi/eno2-79 Not tainted 6.4.0 #364
[   62.655162] Hardware name: Supermicro Super Server/A2SDi-12C-HLN4F, BIOS 1.7a 10/13/2022
[   62.663344] RIP: 0010:__udp_gso_segment (./include/linux/skbuff.h:2858
./include/linux/udp.h:23 net/ipv4/udp_offload.c:228 net/ipv4/udp_offload.c:261
net/ipv4/udp_offload.c:277)
[   62.687193] RSP: 0018:ffffbd3a83b4f868 EFLAGS: 00010246
[   62.692515] RAX: 00000000000000ce RBX: 0000000000000000 RCX: 0000000000000000
[   62.699743] RDX: ffffa124def8a000 RSI: 0000000000000079 RDI: ffffa125952a14d4
[   62.706970] RBP: ffffa124def8a000 R08: 0000000000000022 R09: 00002000001558c9
[   62.714199] R10: 0000000000000000 R11: 00000000be554639 R12: 00000000000000e2
[   62.721426] R13: ffffa125952a1400 R14: ffffa125952a1400 R15: 00002000001558c9
[   62.728654] FS:  0000000000000000(0000) GS:ffffa127efa40000(0000)
knlGS:0000000000000000
[   62.736852] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[   62.742702] CR2: 00000000000000c0 CR3: 00000001034b0000 CR4: 00000000003526e0
[   62.749948] Call Trace:
[   62.752498]  <TASK>
[   62.779267] inet_gso_segment (net/ipv4/af_inet.c:1398)
[   62.787605] skb_mac_gso_segment (net/core/gro.c:141)
[   62.791906] __skb_gso_segment (net/core/dev.c:3403 (discriminator 2))
[   62.800492] validate_xmit_skb (./include/linux/netdevice.h:4862
net/core/dev.c:3659)
[   62.804695] validate_xmit_skb_list (net/core/dev.c:3710)
[   62.809158] sch_direct_xmit (net/sched/sch_generic.c:330)
[   62.813198] __dev_queue_xmit (net/core/dev.c:3805 net/core/dev.c:4210)
net/netfilter/core.c:626)
[   62.821093] br_dev_queue_push_xmit (net/bridge/br_forward.c:55)
[   62.825652] maybe_deliver (net/bridge/br_forward.c:193)
[   62.829420] br_flood (net/bridge/br_forward.c:233)
[   62.832758] br_handle_frame_finish (net/bridge/br_input.c:215)
[   62.837403] br_handle_frame (net/bridge/br_input.c:298
net/bridge/br_input.c:416)
[   62.851417] __netif_receive_skb_core.constprop.0 (net/core/dev.c:5387)
[   62.866114] __netif_receive_skb_list_core (net/core/dev.c:5570)
[   62.871367] netif_receive_skb_list_internal (net/core/dev.c:5638
net/core/dev.c:5727)
[   62.876795] napi_complete_done (./include/linux/list.h:37
./include/net/gro.h:434 ./include/net/gro.h:429 net/core/dev.c:6067)
[   62.881004] ixgbe_poll (drivers/net/ethernet/intel/ixgbe/ixgbe_main.c:3191)
[   62.893534] __napi_poll (net/core/dev.c:6498)
[   62.897133] napi_threaded_poll (./include/linux/netpoll.h:89
net/core/dev.c:6640)
[   62.905276] kthread (kernel/kthread.c:379)
[   62.913435] ret_from_fork (arch/x86/entry/entry_64.S:314)
[   62.917119]  </TASK>

In the critical scenario, rx-gro-list GRO-ed packets are fed, via a
bridge, both to the local input path and to an egress device (tun).

The segmentation of such packets unsafely writes to the cloned skbs
with shared heads.

This change addresses the issue by uncloning as needed the
to-be-segmented skbs.

Reported-by: Ian Kumlien <ian.kumlien@gmail.com>
Tested-by: Ian Kumlien <ian.kumlien@gmail.com>
Fixes: 3a1296a38d0c ("net: Support GRO/GSO fraglist chaining.")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: bgmac: postpone turning IRQs off to avoid SoC hangs

[ Upstream commit e7731194fdf085f46d58b1adccfddbd0dfee4873 ]

Turning IRQs off is done by accessing Ethernet controller registers.
That can't be done until device's clock is enabled. It results in a SoC
hang otherwise.

This bug remained unnoticed for years as most bootloaders keep all
Ethernet interfaces turned on. It seems to only affect a niche SoC
family BCM47189. It has two Ethernet controllers but CFE bootloader uses
only the first one.

Fixes: 34322615cbaa ("net: bgmac: Mask interrupts during probe")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Michal Kubiak <michal.kubiak@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ionic: remove WARN_ON to prevent panic_on_warn

[ Upstream commit abfb2a58a5377ebab717d4362d6180f901b6e5c1 ]

Remove unnecessary early code development check and the WARN_ON
that it uses. The irq alloc and free paths have long been
cleaned up and this check shouldn't have stuck around so long.

Fixes: 77ceb68e29cc ("ionic: Add notifyq support")
Signed-off-by: Nitya Sunkad <nitya.sunkad@amd.com>
Signed-off-by: Shannon Nelson <shannon.nelson@amd.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

octeontx2-af: Move validation of ptp pointer before its usage

[ Upstream commit 7709fbd4922c197efabda03660d93e48a3e80323 ]

Moved PTP pointer validation before its use to avoid smatch warning.
Also used kzalloc/kfree instead of devm_kzalloc/devm_kfree.

Fixes: 2ef4e45d99b1 ("octeontx2-af: Add PTP PPS Errata workaround on CN10K silicon")
Signed-off-by: Naveen Mamindlapalli <naveenm@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Sai Krishna <saikrishnag@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

octeontx2-af: Promisc enable/disable through mbox

[ Upstream commit af42088bdaf292060b8d8a00d8644ca7b2b3f2d1 ]

In legacy silicon, promiscuous mode is only modified
through CGX mbox messages. In CN10KB silicon, it is modified
from CGX mbox and NIX. This breaks legacy application
behaviour. Fix this by removing call from NIX.

Fixes: d6c9784baf59 ("octeontx2-af: Invoke exact match functions if supported")
Signed-off-by: Ratheesh Kannoth <rkannoth@marvell.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Michal Kubiak <michal.kubiak@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

gve: Set default duplex configuration to full

[ Upstream commit 0503efeadbf6bb8bf24397613a73b67e665eac5f ]

Current duplex mode was unset in the driver, resulting in the default
parameter being set to 0, which corresponds to half duplex. It might
mislead users to have incorrect expectation about the driver's
transmission capabilities.
Set the default duplex configuration to full, as the driver runs in
full duplex mode at this point.

Fixes: 7e074d5a76ca ("gve: Enable Link Speed Reporting in the driver.")
Signed-off-by: Junfeng Guo <junfeng.guo@intel.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Message-ID: <20230706044128.2726747-1-junfeng.guo@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net/sched: cls_fw: Fix improper refcount update leads to use-after-free

[ Upstream commit 0323bce598eea038714f941ce2b22541c46d488f ]

In the event of a failure in tcf_change_indev(), fw_set_parms() will
immediately return an error after incrementing or decrementing
reference counter in tcf_bind_filter(). If attacker can control
reference counter to zero and make reference freed, leading to
use after free.

In order to prevent this, move the point of possible failure above the
point where the TC_FW_CLASSID is handled.

Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Reported-by: M A Ramdhan <ramdhan@starlabs.sg>
Signed-off-by: M A Ramdhan <ramdhan@starlabs.sg>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Reviewed-by: Pedro Tammela <pctammela@mojatatu.com>
Message-ID: <20230705161530.52003-1-ramdhan@starlabs.sg>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: mvneta: fix txq_map in case of txq_number==1

[ Upstream commit 21327f81db6337c8843ce755b01523c7d3df715b ]

If we boot with mvneta.txq_number=1, the txq_map is set incorrectly:
MVNETA_CPU_TXQ_ACCESS(1) refers to TX queue 1, but only TX queue 0 is
initialized. Fix this.

Fixes: 50bf8cb6fc9c ("net: mvneta: Configure XPS support")
Signed-off-by: Klaus Kudielka <klaus.kudielka@gmail.com>
Reviewed-by: Michal Kubiak <michal.kubiak@intel.com>
Link: https://lore.kernel.org/r/20230705053712.3914-1-klaus.kudielka@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

bpf: Fix max stack depth check for async callbacks

[ Upstream commit 5415ccd50a8620c8cbaa32d6f18c946c453566f5 ]

The check_max_stack_depth pass happens after the verifier's symbolic
execution, and attempts to walk the call graph of the BPF program,
ensuring that the stack usage stays within bounds for all possible call
chains. There are two cases to consider: bpf_pseudo_func and
bpf_pseudo_call. In the former case, the callback pointer is loaded into
a register, and is assumed that it is passed to some helper later which
calls it (however there is no way to be sure), but the check remains
conservative and accounts the stack usage anyway. For this particular
case, asynchronous callbacks are skipped as they execute asynchronously
when their corresponding event fires.

The case of bpf_pseudo_call is simpler and we know that the call is
definitely made, hence the stack depth of the subprog is accounted for.

However, the current check still skips an asynchronous callback even if
a bpf_pseudo_call was made for it. This is erroneous, as it will miss
accounting for the stack usage of the asynchronous callback, which can
be used to breach the maximum stack depth limit.

Fix this by only skipping asynchronous callbacks when the instruction is
not a pseudo call to the subprog.

Fixes: 7ddc80a476c2 ("bpf: Teach stack depth check about async callbacks.")
Signed-off-by: Kumar Kartikeya Dwivedi <memxor@gmail.com>
Link: https://lore.kernel.org/r/20230705144730.235802-2-memxor@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

scsi: ufs: ufs-mediatek: Add dependency for RESET_CONTROLLER

[ Upstream commit 89f7ef7f2b23b2a7b8ce346c23161916eae5b15c ]

When RESET_CONTROLLER is not set, kconfig complains about missing
dependencies for RESET_TI_SYSCON, so add the missing dependency just as is
done above for SCSI_UFS_QCOM.

Silences this kconfig warning:

WARNING: unmet direct dependencies detected for RESET_TI_SYSCON
  Depends on [n]: RESET_CONTROLLER [=n] && HAS_IOMEM [=y]
  Selected by [m]:
  - SCSI_UFS_MEDIATEK [=m] && SCSI_UFSHCD [=y] && SCSI_UFSHCD_PLATFORM [=y] && ARCH_MEDIATEK [=y]

Fixes: de48898d0cb6 ("scsi: ufs-mediatek: Create reset control device_link")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Link: lore.kernel.org/r/202306020859.1wHg9AaT-lkp@intel.com
Link: https://lore.kernel.org/r/20230701052348.28046-1-rdunlap@infradead.org
Cc: Stanley Chu <stanley.chu@mediatek.com>
Cc: Peter Wang <peter.wang@mediatek.com>
Cc: Paul Gazzillo <paul@pgazz.com>
Cc: Necip Fazil Yildiran <fazilyildiran@gmail.com>
Cc: linux-scsi@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-mediatek@lists.infradead.org
Cc: "James E.J. Bottomley" <jejb@linux.ibm.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

scsi: qla2xxx: Fix error code in qla2x00_start_sp()

[ Upstream commit e579b007eff3ff8d29d59d16214cd85fb9e573f7 ]

This should be negative -EAGAIN instead of positive. The callers treat
non-zero error codes the same so it doesn't really impact runtime beyond
some trivial differences to debug output.

Fixes: 80676d054e5a ("scsi: qla2xxx: Fix session cleanup hang")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Link: https://lore.kernel.org/r/49866d28-4cfe-47b0-842b-78f110e61aab@moroto.mountain
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

blk-crypto: use dynamic lock class for blk_crypto_profile::lock

[ Upstream commit 2fb48d88e77f29bf9d278f25bcfe82cf59a0e09b ]

When a device-mapper device is passing through the inline encryption
support of an underlying device, calls to blk_crypto_evict_key() take
the blk_crypto_profile::lock of the device-mapper device, then take the
blk_crypto_profile::lock of the underlying device (nested).  This isn't
a real deadlock, but it causes a lockdep report because there is only
one lock class for all instances of this lock.

Lockdep subclasses don't really work here because the hierarchy of block
devices is dynamic and could have more than 2 levels.

Instead, register a dynamic lock class for each blk_crypto_profile, and
associate that with the lock.

This avoids false-positive lockdep reports like the following:

    ============================================
    WARNING: possible recursive locking detected
    6.4.0-rc5 #2 Not tainted
    --------------------------------------------
    fscryptctl/1421 is trying to acquire lock:
    ffffff80829ca418 (&profile->lock){++++}-{3:3}, at: __blk_crypto_evict_key+0x44/0x1c0

                   but task is already holding lock:
    ffffff8086b68ca8 (&profile->lock){++++}-{3:3}, at: __blk_crypto_evict_key+0xc8/0x1c0

                   other info that might help us debug this:
     Possible unsafe locking scenario:

           CPU0
           ----
      lock(&profile->lock);
      lock(&profile->lock);

                    *** DEADLOCK ***

     May be due to missing lock nesting notation

Fixes: 1b2628397058 ("block: Keyslot Manager for Inline Encryption")
Reported-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20230610061139.212085-1-ebiggers@kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>

igc: Handle PPS start time programming for past time values

[ Upstream commit 84a192e46106355de1a314d709e657231d4b1026 ]

I225/6 hardware can be programmed to start PPS output once
the time in Target Time registers is reached. The time
programmed in these registers should always be into future.
Only then PPS output is triggered when SYSTIM register
reaches the programmed value. There are two modes in i225/6
hardware to program PPS, pulse and clock mode.

There were issues reported where PPS is not generated when
start time is in past.

Example 1, "echo 0 0 0 2 0 > /sys/class/ptp/ptp0/period"

In the current implementation, a value of '0' is programmed
into Target time registers and PPS output is in pulse mode.
Eventually an interrupt which is triggered upon SYSTIM
register reaching Target time is not fired. Thus no PPS
output is generated.

Example 2, "echo 0 0 0 1 0 > /sys/class/ptp/ptp0/period"

Above case, a value of '0' is programmed into Target time
registers and PPS output is in clock mode. Here, HW tries to
catch-up the current time by incrementing Target Time
register. This catch-up time seem to vary according to
programmed PPS period time as per the HW design. In my
experiments, the delay ranged between few tens of seconds to
few minutes. The PPS output is only generated after the
Target time register reaches current time.

In my experiments, I also observed PPS stopped working with
below test and could not recover until module is removed and
loaded again.

1) echo 0 <future time> 0 1 0 > /sys/class/ptp/ptp1/period
2) echo 0 0 0 1 0 > /sys/class/ptp/ptp1/period
3) echo 0 0 0 1 0 > /sys/class/ptp/ptp1/period

After this PPS did not work even if i re-program with proper
values. I could only get this back working by reloading the
driver.

This patch takes care of calculating and programming
appropriate future time value into Target Time registers.

Fixes: 5e91c72e560c ("igc: Fix PPS delta between two synchronized end-points")
Signed-off-by: Aravindhan Gunasekaran <aravindhan.gunasekaran@intel.com>
Reviewed-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

igc: set TP bit in 'supported' and 'advertising' fields of ethtool_link_ksettings

[ Upstream commit 9ac3fc2f42e5ffa1e927dcbffb71b15fa81459e2 ]

set TP bit in the 'supported' and 'advertising' fields. i225/226 parts
only support twisted pair copper.

Fixes: 8c5ad0dae93c ("igc: Add ethtool support")
Signed-off-by: Prasad Koya <prasad@arista.com>
Acked-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net/mlx5e: Check for NOT_READY flag state after locking

[ Upstream commit 65e64640e97c0f223e77f9ea69b5a46186b93470 ]

Currently the check for NOT_READY flag is performed before obtaining the
necessary lock. This opens a possibility for race condition when the flow
is concurrently removed from unready_flows list by the workqueue task,
which causes a double-removal from the list and a crash[0]. Fix the issue
by moving the flag check inside the section protected by
uplink_priv->unready_flows_lock mutex.

[0]:
[44376.389654] general protection fault, probably for non-canonical address 0xdead000000000108: 0000 [#1] SMP
[44376.391665] CPU: 7 PID: 59123 Comm: tc Not tainted 6.4.0-rc4+ #1
[44376.392984] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014
[44376.395342] RIP: 0010:mlx5e_tc_del_fdb_flow+0xb3/0x340 [mlx5_core]
[44376.396857] Code: 00 48 8b b8 68 ce 02 00 e8 8a 4d 02 00 4c 8d a8 a8 01 00 00 4c 89 ef e8 8b 79 88 e1 48 8b 83 98 06 00 00 48 8b 93 90 06 00 00 <48> 89 42 08 48 89 10 48 b8 00 01 00 00 00 00 ad de 48 89 83 90 06
[44376.399167] RSP: 0018:ffff88812cc97570 EFLAGS: 00010246
[44376.399680] RAX: dead000000000122 RBX: ffff8881088e3800 RCX: ffff8881881bac00
[44376.400337] RDX: dead000000000100 RSI: ffff88812cc97500 RDI: ffff8881242f71b0
[44376.401001] RBP: ffff88811cbb0940 R08: 0000000000000400 R09: 0000000000000001
[44376.401663] R10: 0000000000000001 R11: 0000000000000000 R12: ffff88812c944000
[44376.402342] R13: ffff8881242f71a8 R14: ffff8881222b4000 R15: 0000000000000000
[44376.402999] FS:  00007f0451104800(0000) GS:ffff88852cb80000(0000) knlGS:0000000000000000
[44376.403787] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[44376.404343] CR2: 0000000000489108 CR3: 0000000123a79003 CR4: 0000000000370ea0
[44376.405004] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[44376.405665] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[44376.406339] Call Trace:
[44376.406651]  <TASK>
[44376.406939]  ? die_addr+0x33/0x90
[44376.407311]  ? exc_general_protection+0x192/0x390
[44376.407795]  ? asm_exc_general_protection+0x22/0x30
[44376.408292]  ? mlx5e_tc_del_fdb_flow+0xb3/0x340 [mlx5_core]
[44376.408876]  __mlx5e_tc_del_fdb_peer_flow+0xbc/0xe0 [mlx5_core]
[44376.409482]  mlx5e_tc_del_flow+0x42/0x210 [mlx5_core]
[44376.410055]  mlx5e_flow_put+0x25/0x50 [mlx5_core]
[44376.410529]  mlx5e_delete_flower+0x24b/0x350 [mlx5_core]
[44376.411043]  tc_setup_cb_reoffload+0x22/0x80
[44376.411462]  fl_reoffload+0x261/0x2f0 [cls_flower]
[44376.411907]  ? mlx5e_rep_indr_setup_ft_cb+0x160/0x160 [mlx5_core]
[44376.412481]  ? mlx5e_rep_indr_setup_ft_cb+0x160/0x160 [mlx5_core]
[44376.413044]  tcf_block_playback_offloads+0x76/0x170
[44376.413497]  tcf_block_unbind+0x7b/0xd0
[44376.413881]  tcf_block_setup+0x17d/0x1c0
[44376.414269]  tcf_block_offload_cmd.isra.0+0xf1/0x130
[44376.414725]  tcf_block_offload_unbind+0x43/0x70
[44376.415153]  __tcf_block_put+0x82/0x150
[44376.415532]  ingress_destroy+0x22/0x30 [sch_ingress]
[44376.415986]  qdisc_destroy+0x3b/0xd0
[44376.416343]  qdisc_graft+0x4d0/0x620
[44376.416706]  tc_get_qdisc+0x1c9/0x3b0
[44376.417074]  rtnetlink_rcv_msg+0x29c/0x390
[44376.419978]  ? rep_movs_alternative+0x3a/0xa0
[44376.420399]  ? rtnl_calcit.isra.0+0x120/0x120
[44376.420813]  netlink_rcv_skb+0x54/0x100
[44376.421192]  netlink_unicast+0x1f6/0x2c0
[44376.421573]  netlink_sendmsg+0x232/0x4a0
[44376.421980]  sock_sendmsg+0x38/0x60
[44376.422328]  ____sys_sendmsg+0x1d0/0x1e0
[44376.422709]  ? copy_msghdr_from_user+0x6d/0xa0
[44376.423127]  ___sys_sendmsg+0x80/0xc0
[44376.423495]  ? ___sys_recvmsg+0x8b/0xc0
[44376.423869]  __sys_sendmsg+0x51/0x90
[44376.424226]  do_syscall_64+0x3d/0x90
[44376.424587]  entry_SYSCALL_64_after_hwframe+0x46/0xb0
[44376.425046] RIP: 0033:0x7f045134f887
[44376.425403] Code: 0a 00 f7 d8 64 89 02 48 c7 c0 ff ff ff ff eb b9 0f 1f 00 f3 0f 1e fa 64 8b 04 25 18 00 00 00 85 c0 75 10 b8 2e 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 51 c3 48 83 ec 28 89 54 24 1c 48 89 74 24 10
[44376.426914] RSP: 002b:00007ffd63a82b98 EFLAGS: 00000246 ORIG_RAX: 000000000000002e
[44376.427592] RAX: ffffffffffffffda RBX: 000000006481955f RCX: 00007f045134f887
[44376.428195] RDX: 0000000000000000 RSI: 00007ffd63a82c00 RDI: 0000000000000003
[44376.428796] RBP: 0000000000000000 R08: 0000000000000001 R09: 0000000000000000
[44376.429404] R10: 00007f0451208708 R11: 0000000000000246 R12: 0000000000000001
[44376.430039] R13: 0000000000409980 R14: 000000000047e538 R15: 0000000000485400
[44376.430644]  </TASK>
[44376.430907] Modules linked in: mlx5_ib mlx5_core act_mirred act_tunnel_key cls_flower vxlan dummy sch_ingress openvswitch nsh rpcrdma rdma_ucm ib_iser libiscsi scsi_transport_iscsi ib_umad rdma_cm ib_ipoib iw_cm ib_cm ib_uverbs ib_core xt_conntrack xt_MASQUERADE nf_conntrack_netlink nfnetlink xt_addrtype iptable_nat nf_nat br_netfilter rpcsec_g
ss_krb5 auth_rpcgss oid_registry overlay zram zsmalloc fuse [last unloaded: mlx5_core]
[44376.433936] ---[ end trace 0000000000000000 ]---
[44376.434373] RIP: 0010:mlx5e_tc_del_fdb_flow+0xb3/0x340 [mlx5_core]
[44376.434951] Code: 00 48 8b b8 68 ce 02 00 e8 8a 4d 02 00 4c 8d a8 a8 01 00 00 4c 89 ef e8 8b 79 88 e1 48 8b 83 98 06 00 00 48 8b 93 90 06 00 00 <48> 89 42 08 48 89 10 48 b8 00 01 00 00 00 00 ad de 48 89 83 90 06
[44376.436452] RSP: 0018:ffff88812cc97570 EFLAGS: 00010246
[44376.436924] RAX: dead000000000122 RBX: ffff8881088e3800 RCX: ffff8881881bac00
[44376.437530] RDX: dead000000000100 RSI: ffff88812cc97500 RDI: ffff8881242f71b0
[44376.438179] RBP: ffff88811cbb0940 R08: 0000000000000400 R09: 0000000000000001
[44376.438786] R10: 0000000000000001 R11: 0000000000000000 R12: ffff88812c944000
[44376.439393] R13: ffff8881242f71a8 R14: ffff8881222b4000 R15: 0000000000000000
[44376.439998] FS:  00007f0451104800(0000) GS:ffff88852cb80000(0000) knlGS:0000000000000000
[44376.440714] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[44376.441225] CR2: 0000000000489108 CR3: 0000000123a79003 CR4: 0000000000370ea0
[44376.441843] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[44376.442471] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400

Fixes: ad86755b18d5 ("net/mlx5e: Protect unready flows with dedicated lock")
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net/mlx5e: fix memory leak in mlx5e_ptp_open

[ Upstream commit d543b649ffe58a0cb4b6948b3305069c5980a1fa ]

When kvzalloc_node or kvzalloc failed in mlx5e_ptp_open, the memory
pointed by "c" or "cparams" is not freed, which can lead to a memory
leak. Fix by freeing the array in the error path.

Fixes: 145e5637d941 ("net/mlx5e: Add TX PTP port object support")
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Reviewed-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Reviewed-by: Gal Pressman <gal@nvidia.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net/mlx5e: fix memory leak in mlx5e_fs_tt_redirect_any_create

[ Upstream commit 3250affdc658557a41df9c5fb567723e421f8bf2 ]

The memory pointed to by the fs->any pointer is not freed in the error
path of mlx5e_fs_tt_redirect_any_create, which can lead to a memory leak.
Fix by freeing the memory in the error path, thereby making the error path
identical to mlx5e_fs_tt_redirect_any_destroy().

Fixes: 0f575c20bf06 ("net/mlx5e: Introduce Flow Steering ANY API")
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net/mlx5e: fix double free in mlx5e_destroy_flow_table

[ Upstream commit 884abe45a9014d0de2e6edb0630dfd64f23f1d1b ]

In function accel_fs_tcp_create_groups(), when the ft->g memory is
successfully allocated but the 'in' memory fails to be allocated, the
memory pointed to by ft->g is released once. And in function
accel_fs_tcp_create_table, mlx5e_destroy_flow_table is called to release
the memory pointed to by ft->g again. This will cause double free problem.

Fixes: c062d52ac24c ("net/mlx5e: Receive flow steering framework for accelerated TCP flows")
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

igc: Remove delay during TX ring configuration

[ Upstream commit cca28ceac7c7857bc2d313777017585aef00bcc4 ]

Remove unnecessary delay during the TX ring configuration.
This will cause delay, especially during link down and
link up activity.

Furthermore, old SKUs like as I225 will call the reset_adapter
to reset the controller during TSN mode Gate Control List (GCL)
setting. This will add more time to the configuration of the
real-time use case.

It doesn't mentioned about this delay in the Software User Manual.
It might have been ported from legacy code I210 in the past.

Fixes: 13b5b7fd6a4a ("igc: Add support for Tx/Rx rings")
Signed-off-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com>
Acked-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ice: Fix max_rate check while configuring TX rate limits

[ Upstream commit 5f16da6ee6ac32e6c8098bc4cfcc4f170694f9da ]

Remove incorrect check in ice_validate_mqprio_opt() that limits
filter configuration when sum of max_rates of all TCs exceeds
the link speed. The max rate of each TC is unrelated to value
used by other TCs and is valid as long as it is less than link
speed.

Fixes: fbc7b27af0f9 ("ice: enable ndo_setup_tc support for mqprio_qdisc")
Signed-off-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Signed-off-by: Sudheer Mogilappagari <sudheer.mogilappagari@intel.com>
Tested-by: Bharathi Sreenivas <bharathi.sreenivas@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/panel: simple: Add Powertip PH800480T013 drm_display_mode flags

[ Upstream commit 1c519980aced3da1fae37c1339cf43b24eccdee7 ]

Add missing drm_display_mode DRM_MODE_FLAG_NVSYNC | DRM_MODE_FLAG_NHSYNC
flags. Those are used by various bridges in the pipeline to correctly
configure its sync signals polarity.

Fixes: d69de69f2be1 ("drm/panel: simple: Add Powertip PH800480T013 panel")
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230615201602.565948-1-marex@denx.de
Signed-off-by: Sasha Levin <sashal@kernel.org>

swiotlb: reduce the number of areas to match actual memory pool size

[ Upstream commit 8ac04063354a01a484d2e55d20ed1958aa0d3392 ]

Although the desired size of the SWIOTLB memory pool is increased in
swiotlb_adjust_nareas() to match the number of areas, the actual allocation
may be smaller, which may require reducing the number of areas.

For example, Xen uses swiotlb_init_late(), which in turn uses the page
allocator. On x86, page size is 4 KiB and MAX_ORDER is 10 (1024 pages),
resulting in a maximum memory pool size of 4 MiB. This corresponds to 2048
slots of 2 KiB each. The minimum area size is 128 (IO_TLB_SEGSIZE),
allowing at most 2048 / 128 = 16 areas.

If num_possible_cpus() is greater than the maximum number of areas, areas
are smaller than IO_TLB_SEGSIZE and contiguous groups of free slots will
span multiple areas. When allocating and freeing slots, only one area will
be properly locked, causing race conditions on the unlocked slots and
ultimately data corruption, kernel hangs and crashes.

Fixes: 20347fca71a3 ("swiotlb: split up the global swiotlb lock")
Signed-off-by: Petr Tesarik <petr.tesarik.ext@huawei.com>
Reviewed-by: Roberto Sassu <roberto.sassu@huawei.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

swiotlb: reduce the swiotlb buffer size on allocation failure

[ Upstream commit 8d58aa484920c4f9be4834a7aeb446cdced21a37 ]

At the moment the AMD encrypted platform reserves 6% of RAM for SWIOTLB
or 1GB, whichever is less. However it is possible that there is no block
big enough in the low memory which make SWIOTLB allocation fail and
the kernel continues without DMA. In such case a VM hangs on DMA.

This moves alloc+remap to a helper and calls it from a loop where
the size is halved on each iteration.

This updates default_nslabs on successful allocation which looks like
an oversight as not doing so should have broken callers of
swiotlb_size_or_default().

Signed-off-by: Alexey Kardashevskiy <aik@amd.com>
Reviewed-by: Pankaj Gupta <pankaj.gupta@amd.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Stable-dep-of: 8ac04063354a ("swiotlb: reduce the number of areas to match actual memory pool size")
Signed-off-by: Sasha Levin <sashal@kernel.org>

swiotlb: always set the number of areas before allocating the pool

[ Upstream commit aabd12609f91155f26584508b01f548215cc3c0c ]

The number of areas defaults to the number of possible CPUs. However, the
total number of slots may have to be increased after adjusting the number
of areas. Consequently, the number of areas must be determined before
allocating the memory pool. This is even explained with a comment in
swiotlb_init_remap(), but swiotlb_init_late() adjusts the number of areas
after slots are already allocated. The areas may end up being smaller than
IO_TLB_SEGSIZE, which breaks per-area locking.

While fixing swiotlb_init_late(), move all relevant comments before the
definition of swiotlb_adjust_nareas() and convert them to kernel-doc.

Fixes: 20347fca71a3 ("swiotlb: split up the global swiotlb lock")
Signed-off-by: Petr Tesarik <petr.tesarik.ext@huawei.com>
Reviewed-by: Roberto Sassu <roberto.sassu@huawei.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/bridge: ti-sn65dsi86: Fix auxiliary bus lifetime

[ Upstream commit 7aa83fbd712a6f08ffa67890061f26d140c2a84f ]

Memory for the "struct device" for any given device isn't supposed to
be released until the device's release() is called. This is important
because someone might be holding a kobject reference to the "struct
device" and might try to access one of its members even after any
other cleanup/uninitialization has happened.

Code analysis of ti-sn65dsi86 shows that this isn't quite right. When
the code was written, it was believed that we could rely on the fact
that the child devices would all be freed before the parent devices
and thus we didn't need to worry about a release() function. While I
still believe that the parent's "struct device" is guaranteed to
outlive the child's "struct device" (because the child holds a kobject
reference to the parent), the parent's "devm" allocated memory is a
different story. That appears to be freed much earlier.

Let's make this better for ti-sn65dsi86 by allocating each auxiliary
with kzalloc and then free that memory in the release().

Fixes: bf73537f411b ("drm/bridge: ti-sn65dsi86: Break GPIO and MIPI-to-eDP bridge into sub-drivers")
Suggested-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230613065812.v2.1.I24b838a5b4151fb32bccd6f36397998ea2df9fbb@changeid
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/panel: simple: Add connector_type for innolux_at043tn24

[ Upstream commit 2c56a751845ddfd3078ebe79981aaaa182629163 ]

The innolux at043tn24 display is a parallel LCD. Pass the 'connector_type'
information to avoid the following warning:

panel-simple panel: Specify missing connector_type

Signed-off-by: Fabio Estevam <festevam@denx.de>
Fixes: 41bcceb4de9c ("drm/panel: simple: Add support for Innolux AT043TN24")
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230620112202.654981-1-festevam@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

ksmbd: fix out of bounds read in smb2_sess_setup

commit 98422bdd4cb3ca4d08844046f6507d7ec2c2b8d8 upstream.

ksmbd does not consider the case of that smb2 session setup is
in compound request. If this is the second payload of the compound,
OOB read issue occurs while processing the first payload in
the smb2_sess_setup().

Cc: stable@vger.kernel.org
Reported-by: zdi-disclosures@trendmicro.com # ZDI-CAN-21355
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ksmbd: add missing compound request handing in some commands

commit 7b7d709ef7cf285309157fb94c33f625dd22c5e1 upstream.

This patch add the compound request handling to the some commands.
Existing clients do not send these commands as compound requests,
but ksmbd should consider that they may come.

Cc: stable@vger.kernel.org
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

workqueue: clean up WORK_* constant types, clarify masking

commit afa4bb778e48d79e4a642ed41e3b4e0de7489a6c upstream.

Dave Airlie reports that gcc-13.1.1 has started complaining about some
of the workqueue code in 32-bit arm builds:

  kernel/workqueue.c: In function ‘get_work_pwq’:
  kernel/workqueue.c:713:24: error: cast to pointer from integer of different size [-Werror=int-to-pointer-cast]
    713 |                 return (void *)(data & WORK_STRUCT_WQ_DATA_MASK);
        |                        ^
  [ ... a couple of other cases ... ]

and while it's not immediately clear exactly why gcc started complaining
about it now, I suspect it's some C23-induced enum type handlign fixup in
gcc-13 is the cause.

Whatever the reason for starting to complain, the code and data types
are indeed disgusting enough that the complaint is warranted.

The wq code ends up creating various "helper constants" (like that
WORK_STRUCT_WQ_DATA_MASK) using an enum type, which is all kinds of
confused.  The mask needs to be 'unsigned long', not some unspecified
enum type.

To make matters worse, the actual "mask and cast to a pointer" is
repeated a couple of times, and the cast isn't even always done to the
right pointer, but - as the error case above - to a 'void *' with then
the compiler finishing the job.

That's now how we roll in the kernel.

So create the masks using the proper types rather than some ambiguous
enumeration, and use a nice helper that actually does the type
conversion in one well-defined place.

Incidentally, this magically makes clang generate better code.  That,
admittedly, is really just a sign of clang having been seriously
confused before, and cleaning up the typing unconfuses the compiler too.

Reported-by: Dave Airlie <airlied@gmail.com>
Link: https://lore.kernel.org/lkml/CAPM=9twNnV4zMCvrPkw3H-ajZOH-01JVh_kDrxdPYQErz8ZTdA@mail.gmail.com/
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Tejun Heo <tj@kernel.org>
Cc: Nick Desaulniers <ndesaulniers@google.com>
Cc: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: lan743x: Don't sleep in atomic context

commit 7a8227b2e76be506b2ac64d2beac950ca04892a5 upstream.

dev_set_rx_mode() grabs a spin_lock, and the lan743x implementation
proceeds subsequently to go to sleep using readx_poll_timeout().

Introduce a helper wrapping the readx_poll_timeout_atomic() function
and use it to replace the calls to readx_polL_timeout().

Fixes: 23f0703c125b ("lan743x: Add main source files for new lan743x driver")
Cc: stable@vger.kernel.org
Cc: Bryan Whitehead <bryan.whitehead@microchip.com>
Cc: UNGLinuxDriver@microchip.com
Signed-off-by: Moritz Fischer <moritzf@google.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230627035000.1295254-1-moritzf@google.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

HID: amd_sfh: Fix for shift-out-of-bounds

commit 87854366176403438d01f368b09de3ec2234e0f5 upstream.

Shift operation of 'exp' and 'shift' variables exceeds the maximum number
of shift values in the u32 range leading to UBSAN shift-out-of-bounds.

...
[    6.120512] UBSAN: shift-out-of-bounds in drivers/hid/amd-sfh-hid/sfh1_1/amd_sfh_desc.c:149:50
[    6.120598] shift exponent 104 is too large for 64-bit type 'long unsigned int'
[    6.120659] CPU: 4 PID: 96 Comm: kworker/4:1 Not tainted 6.4.0amd_1-next-20230519-dirty #10
[    6.120665] Hardware name: AMD Birman-PHX/Birman-PHX, BIOS SFH_with_HPD_SEN.FD 04/05/2023
[    6.120667] Workqueue: events amd_sfh_work_buffer [amd_sfh]
[    6.120687] Call Trace:
[    6.120690]  <TASK>
[    6.120694]  dump_stack_lvl+0x48/0x70
[    6.120704]  dump_stack+0x10/0x20
[    6.120707]  ubsan_epilogue+0x9/0x40
[    6.120716]  __ubsan_handle_shift_out_of_bounds+0x10f/0x170
[    6.120720]  ? psi_group_change+0x25f/0x4b0
[    6.120729]  float_to_int.cold+0x18/0xba [amd_sfh]
[    6.120739]  get_input_rep+0x57/0x340 [amd_sfh]
[    6.120748]  ? __schedule+0xba7/0x1b60
[    6.120756]  ? __pfx_get_input_rep+0x10/0x10 [amd_sfh]
[    6.120764]  amd_sfh_work_buffer+0x91/0x180 [amd_sfh]
[    6.120772]  process_one_work+0x229/0x430
[    6.120780]  worker_thread+0x4a/0x3c0
[    6.120784]  ? __pfx_worker_thread+0x10/0x10
[    6.120788]  kthread+0xf7/0x130
[    6.120792]  ? __pfx_kthread+0x10/0x10
[    6.120795]  ret_from_fork+0x29/0x50
[    6.120804]  </TASK>
...

Fix this by adding the condition to validate shift ranges.

Fixes: 93ce5e0231d7 ("HID: amd_sfh: Implement SFH1.1 functionality")
Cc: stable@vger.kernel.org
Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Signed-off-by: Akshata MukundShetty <akshata.mukundshetty@amd.com>
Link: https://lore.kernel.org/r/20230707065722.9036-3-Basavaraj.Natikar@amd.com
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

HID: amd_sfh: Rename the float32 variable

commit c1685a862a4bea863537f06abaa37a123aef493c upstream.

As float32 is also used in other places as a data type, it is necessary
to rename the float32 variable in order to avoid confusion.

Cc: stable@vger.kernel.org
Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Signed-off-by: Akshata MukundShetty <akshata.mukundshetty@amd.com>
Link: https://lore.kernel.org/r/20230707065722.9036-2-Basavaraj.Natikar@amd.com
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Linux 6.1.39

Link: https://lore.kernel.org/r/20230716194923.861634455@linuxfoundation.org
Tested-by: Takeshi Ogasawara <takeshi.ogasawara@futuring-girl.com>
Tested-by: Conor Dooley <conor.dooley@microchip.com>
Tested-by: Shuah Khan <skhan@linuxfoundation.org>
Link: https://lore.kernel.org/r/20230717185609.886113843@linuxfoundation.org
Link: https://lore.kernel.org/r/20230717201547.359923764@linuxfoundation.org
Tested-by: Takeshi Ogasawara <takeshi.ogasawara@futuring-girl.com>
Tested-by: Bagas Sanjaya <bagasdotme@gmail.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Chris Paterson (CIP) <chris.paterson2@renesas.com>
Tested-by: Ron Economos <re@w6rz.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Joel Fernandes (Google) <joel@joelfernandes.org>
Tested-by: Allen Pais <apais@linux.microsoft.com>
Tested-by: SeongJae Park <sj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

io_uring: Use io_schedule* in cqring wait

Commit 8a796565cec3601071cbbd27d6304e202019d014 upstream.

I observed poor performance of io_uring compared to synchronous IO. That
turns out to be caused by deeper CPU idle states entered with io_uring,
due to io_uring using plain schedule(), whereas synchronous IO uses
io_schedule().

The losses due to this are substantial. On my cascade lake workstation,
t/io_uring from the fio repository e.g. yields regressions between 20%
and 40% with the following command:
./t/io_uring -r 5 -X0 -d 1 -s 1 -c 1 -p 0 -S$use_sync -R 0 /mnt/t2/fio/write.0.0

This is repeatable with different filesystems, using raw block devices
and using different block devices.

Use io_schedule_prepare() / io_schedule_finish() in
io_cqring_wait_schedule() to address the difference.

After that using io_uring is on par or surpassing synchronous IO (using
registered files etc makes it reliably win, but arguably is a less fair
comparison).

There are other calls to schedule() in io_uring/, but none immediately
jump out to be similarly situated, so I did not touch them. Similarly,
it's possible that mutex_lock_io() should be used, but it's not clear if
there are cases where that matters.

Cc: stable@vger.kernel.org # 5.10+
Cc: Pavel Begunkov <asml.silence@gmail.com>
Cc: io-uring@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Andres Freund <andres@anarazel.de>
Link: https://lore.kernel.org/r/20230707162007.194068-1-andres@anarazel.de
[axboe: minor style fixup]
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

sh: hd64461: Handle virq offset for offchip IRQ base and HD64461 IRQ

commit 7c28a35e19fafa1d3b367bcd3ec4021427a9397b upstream.

A recent change to start counting SuperH IRQ #s from 16 breaks support
for the Hitachi HD64461 companion chip.

Move the offchip IRQ base and HD64461 IRQ # by 16 in order to
accommodate for the new virq numbering rules.

Fixes: a8ac2961148e ("sh: Avoid using IRQ0 on SH3 and SH4")
Signed-off-by: Artur Rojek <contact@artur-rojek.eu>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
Link: https://lore.kernel.org/r/20230710233132.69734-1-contact@artur-rojek.eu
Signed-off-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

sh: mach-dreamcast: Handle virq offset in cascaded IRQ demux

commit 3d20f7a6eb76afdf9d4ad9cb864c2e2da9c38e1f upstream.

Take into account the virq offset when translating cascaded interrupts.

Fixes: a8ac2961148e8c72 ("sh: Avoid using IRQ0 on SH3 and SH4")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
Link: https://lore.kernel.org/r/7d0cb246c9f1cd24bb1f637ec5cb67e799a4c3b8.1688908227.git.geert+renesas@glider.be
Signed-off-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

sh: mach-highlander: Handle virq offset in cascaded IRL demux

commit a2601b8d8f077368c6d113b4d496559415c6d495 upstream.

Take into account the virq offset when translating cascaded IRL
interrupts.

Fixes: a8ac2961148e8c72 ("sh: Avoid using IRQ0 on SH3 and SH4")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
Link: https://lore.kernel.org/r/4fcb0d08a2b372431c41e04312742dc9e41e1be4.1688908186.git.geert+renesas@glider.be
Signed-off-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

sh: mach-r2d: Handle virq offset in cascaded IRL demux

commit ab8aa4f0956d2e0fb8344deadb823ef743581795 upstream.

When booting rts7751r2dplus_defconfig on QEMU, the system hangs due to
an interrupt storm on IRQ 20. IRQ 20 aka event 0x280 is a cascaded IRL
interrupt, which maps to IRQ_VOYAGER, the interrupt used by the Silicon
Motion SM501 multimedia companion chip. As rts7751r2d_irq_demux() does
not take into account the new virq offset, the interrupt is no longer
translated, leading to an unhandled interrupt.

Fix this by taking into account the virq offset when translating
cascaded IRL interrupts.

Fixes: a8ac2961148e8c72 ("sh: Avoid using IRQ0 on SH3 and SH4")
Reported-by: Guenter Roeck <linux@roeck-us.net>
Closes: https://lore.kernel.org/r/fbfea3ad-d327-4ad5-ac9c-648c7ca3fe1f@roeck-us.net
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
Tested-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/2c99d5df41c40691f6c407b7b6a040d406bc81ac.1688901306.git.geert+renesas@glider.be
Signed-off-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

block/partition: fix signedness issue for Amiga partitions

commit 7eb1e47696aa231b1a567846bbe3a1e1befe1854 upstream.

Making 'blk' sector_t (i.e. 64 bit if LBD support is active) fails the
'blk>0' test in the partition block loop if a value of (signed int) -1 is
used to mark the end of the partition block list.

Explicitly cast 'blk' to signed int to allow use of -1 to terminate the
partition block linked list.

Fixes: b6f3f28f604b ("block: add overflow checks for Amiga partition support")
Reported-by: Christian Zigotzky <chzigotzky@xenosoft.de>
Link: https://lore.kernel.org/r/024ce4fa-cc6d-50a2-9aae-3701d0ebf668@xenosoft.de
Signed-off-by: Michael Schmitz <schmitzmic@gmail.com>
Reviewed-by: Martin Steigerwald <martin@lichtvoll.de>
Tested-by: Christian Zigotzky <chzigotzky@xenosoft.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tty: serial: fsl_lpuart: add earlycon for imx8ulp platform

commit e0edfdc15863ec80a1d9ac6e174dbccc00206dd0 upstream.

Add earlycon support for imx8ulp platform.

Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20230619080613.16522-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

wireguard: netlink: send staged packets when setting initial private key

commit f58d0a9b4c6a7a5199c3af967e43cc8b654604d4 upstream.

Packets bound for peers can queue up prior to the device private key
being set. For example, if persistent keepalive is set, a packet is
queued up to be sent as soon as the device comes up. However, if the
private key hasn't been set yet, the handshake message never sends, and
no timer is armed to retry, since that would be pointless.

But, if a user later sets a private key, the expectation is that those
queued packets, such as a persistent keepalive, are actually sent. So
adjust the configuration logic to account for this edge case, and add a
test case to make sure this works.

Maxim noticed this with a wg-quick(8) config to the tune of:

    [Interface]
    PostUp = wg set %i private-key somefile

    [Peer]
    PublicKey = ...
    Endpoint = ...
    PersistentKeepalive = 25

Here, the private key gets set after the device comes up using a PostUp
script, triggering the bug.

Fixes: e7096c131e51 ("net: WireGuard secure network tunnel")
Cc: stable@vger.kernel.org
Reported-by: Maxim Cournoyer <maxim.cournoyer@gmail.com>
Tested-by: Maxim Cournoyer <maxim.cournoyer@gmail.com>
Link: https://lore.kernel.org/wireguard/87fs7xtqrv.fsf@gmail.com/
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

wireguard: queueing: use saner cpu selection wrapping

commit 7387943fa35516f6f8017a3b0e9ce48a3bef9faa upstream.

Using `% nr_cpumask_bits` is slow and complicated, and not totally
robust toward dynamic changes to CPU topologies. Rather than storing the
next CPU in the round-robin, just store the last one, and also return
that value. This simplifies the loop drastically into a much more common
pattern.

Fixes: e7096c131e51 ("net: WireGuard secure network tunnel")
Cc: stable@vger.kernel.org
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Tested-by: Manuel Leiner <manuel.leiner@gmx.de>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

netfilter: nf_tables: prevent OOB access in nft_byteorder_eval

commit caf3ef7468f7534771b5c44cd8dbd6f7f87c2cbd upstream.

When evaluating byteorder expressions with size 2, a union with 32-bit and
16-bit members is used. Since the 16-bit members are aligned to 32-bit,
the array accesses will be out-of-bounds.

It may lead to a stack-out-of-bounds access like the one below:

[   23.095215] ==================================================================
[   23.095625] BUG: KASAN: stack-out-of-bounds in nft_byteorder_eval+0x13c/0x320
[   23.096020] Read of size 2 at addr ffffc90000007948 by task ping/115
[   23.096358]
[   23.096456] CPU: 0 PID: 115 Comm: ping Not tainted 6.4.0+ #413
[   23.096770] Call Trace:
[   23.096910]  <IRQ>
[   23.097030]  dump_stack_lvl+0x60/0xc0
[   23.097218]  print_report+0xcf/0x630
[   23.097388]  ? nft_byteorder_eval+0x13c/0x320
[   23.097577]  ? kasan_addr_to_slab+0xd/0xc0
[   23.097760]  ? nft_byteorder_eval+0x13c/0x320
[   23.097949]  kasan_report+0xc9/0x110
[   23.098106]  ? nft_byteorder_eval+0x13c/0x320
[   23.098298]  __asan_load2+0x83/0xd0
[   23.098453]  nft_byteorder_eval+0x13c/0x320
[   23.098659]  nft_do_chain+0x1c8/0xc50
[   23.098852]  ? __pfx_nft_do_chain+0x10/0x10
[   23.099078]  ? __kasan_check_read+0x11/0x20
[   23.099295]  ? __pfx___lock_acquire+0x10/0x10
[   23.099535]  ? __pfx___lock_acquire+0x10/0x10
[   23.099745]  ? __kasan_check_read+0x11/0x20
[   23.099929]  nft_do_chain_ipv4+0xfe/0x140
[   23.100105]  ? __pfx_nft_do_chain_ipv4+0x10/0x10
[   23.100327]  ? lock_release+0x204/0x400
[   23.100515]  ? nf_hook.constprop.0+0x340/0x550
[   23.100779]  nf_hook_slow+0x6c/0x100
[   23.100977]  ? __pfx_nft_do_chain_ipv4+0x10/0x10
[   23.101223]  nf_hook.constprop.0+0x334/0x550
[   23.101443]  ? __pfx_ip_local_deliver_finish+0x10/0x10
[   23.101677]  ? __pfx_nf_hook.constprop.0+0x10/0x10
[   23.101882]  ? __pfx_ip_rcv_finish+0x10/0x10
[   23.102071]  ? __pfx_ip_local_deliver_finish+0x10/0x10
[   23.102291]  ? rcu_read_lock_held+0x4b/0x70
[   23.102481]  ip_local_deliver+0xbb/0x110
[   23.102665]  ? __pfx_ip_rcv+0x10/0x10
[   23.102839]  ip_rcv+0x199/0x2a0
[   23.102980]  ? __pfx_ip_rcv+0x10/0x10
[   23.103140]  __netif_receive_skb_one_core+0x13e/0x150
[   23.103362]  ? __pfx___netif_receive_skb_one_core+0x10/0x10
[   23.103647]  ? mark_held_locks+0x48/0xa0
[   23.103819]  ? process_backlog+0x36c/0x380
[   23.103999]  __netif_receive_skb+0x23/0xc0
[   23.104179]  process_backlog+0x91/0x380
[   23.104350]  __napi_poll.constprop.0+0x66/0x360
[   23.104589]  ? net_rx_action+0x1cb/0x610
[   23.104811]  net_rx_action+0x33e/0x610
[   23.105024]  ? _raw_spin_unlock+0x23/0x50
[   23.105257]  ? __pfx_net_rx_action+0x10/0x10
[   23.105485]  ? mark_held_locks+0x48/0xa0
[   23.105741]  __do_softirq+0xfa/0x5ab
[   23.105956]  ? __dev_queue_xmit+0x765/0x1c00
[   23.106193]  do_softirq.part.0+0x49/0xc0
[   23.106423]  </IRQ>
[   23.106547]  <TASK>
[   23.106670]  __local_bh_enable_ip+0xf5/0x120
[   23.106903]  __dev_queue_xmit+0x789/0x1c00
[   23.107131]  ? __pfx___dev_queue_xmit+0x10/0x10
[   23.107381]  ? find_held_lock+0x8e/0xb0
[   23.107585]  ? lock_release+0x204/0x400
[   23.107798]  ? neigh_resolve_output+0x185/0x350
[   23.108049]  ? mark_held_locks+0x48/0xa0
[   23.108265]  ? neigh_resolve_output+0x185/0x350
[   23.108514]  neigh_resolve_output+0x246/0x350
[   23.108753]  ? neigh_resolve_output+0x246/0x350
[   23.109003]  ip_finish_output2+0x3c3/0x10b0
[   23.109250]  ? __pfx_ip_finish_output2+0x10/0x10
[   23.109510]  ? __pfx_nf_hook+0x10/0x10
[   23.109732]  __ip_finish_output+0x217/0x390
[   23.109978]  ip_finish_output+0x2f/0x130
[   23.110207]  ip_output+0xc9/0x170
[   23.110404]  ip_push_pending_frames+0x1a0/0x240
[   23.110652]  raw_sendmsg+0x102e/0x19e0
[   23.110871]  ? __pfx_raw_sendmsg+0x10/0x10
[   23.111093]  ? lock_release+0x204/0x400
[   23.111304]  ? __mod_lruvec_page_state+0x148/0x330
[   23.111567]  ? find_held_lock+0x8e/0xb0
[   23.111777]  ? find_held_lock+0x8e/0xb0
[   23.111993]  ? __rcu_read_unlock+0x7c/0x2f0
[   23.112225]  ? aa_sk_perm+0x18a/0x550
[   23.112431]  ? filemap_map_pages+0x4f1/0x900
[   23.112665]  ? __pfx_aa_sk_perm+0x10/0x10
[   23.112880]  ? find_held_lock+0x8e/0xb0
[   23.113098]  inet_sendmsg+0xa0/0xb0
[   23.113297]  ? inet_sendmsg+0xa0/0xb0
[   23.113500]  ? __pfx_inet_sendmsg+0x10/0x10
[   23.113727]  sock_sendmsg+0xf4/0x100
[   23.113924]  ? move_addr_to_kernel.part.0+0x4f/0xa0
[   23.114190]  __sys_sendto+0x1d4/0x290
[   23.114391]  ? __pfx___sys_sendto+0x10/0x10
[   23.114621]  ? __pfx_mark_lock.part.0+0x10/0x10
[   23.114869]  ? lock_release+0x204/0x400
[   23.115076]  ? find_held_lock+0x8e/0xb0
[   23.115287]  ? rcu_is_watching+0x23/0x60
[   23.115503]  ? __rseq_handle_notify_resume+0x6e2/0x860
[   23.115778]  ? __kasan_check_write+0x14/0x30
[   23.116008]  ? blkcg_maybe_throttle_current+0x8d/0x770
[   23.116285]  ? mark_held_locks+0x28/0xa0
[   23.116503]  ? do_syscall_64+0x37/0x90
[   23.116713]  __x64_sys_sendto+0x7f/0xb0
[   23.116924]  do_syscall_64+0x59/0x90
[   23.117123]  ? irqentry_exit_to_user_mode+0x25/0x30
[   23.117387]  ? irqentry_exit+0x77/0xb0
[   23.117593]  ? exc_page_fault+0x92/0x140
[   23.117806]  entry_SYSCALL_64_after_hwframe+0x6e/0xd8
[   23.118081] RIP: 0033:0x7f744aee2bba
[   23.118282] Code: d8 64 89 02 48 c7 c0 ff ff ff ff eb b8 0f 1f 00 f3 0f 1e fa 41 89 ca 64 8b 04 25 18 00 00 00 85 c0 75 15 b8 2c 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 7e c3 0f 1f 44 00 00 41 54 48 83 ec 30 44 89
[   23.119237] RSP: 002b:00007ffd04a7c9f8 EFLAGS: 00000246 ORIG_RAX: 000000000000002c
[   23.119644] RAX: ffffffffffffffda RBX: 00007ffd04a7e0a0 RCX: 00007f744aee2bba
[   23.120023] RDX: 0000000000000040 RSI: 000056488e9e6300 RDI: 0000000000000003
[   23.120413] RBP: 000056488e9e6300 R08: 00007ffd04a80320 R09: 0000000000000010
[   23.120809] R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000040
[   23.121219] R13: 00007ffd04a7dc38 R14: 00007ffd04a7ca00 R15: 00007ffd04a7e0a0
[   23.121617]  </TASK>
[   23.121749]
[   23.121845] The buggy address belongs to the virtual mapping at
[   23.121845]  [ffffc90000000000, ffffc90000009000) created by:
[   23.121845]  irq_init_percpu_irqstack+0x1cf/0x270
[   23.122707]
[   23.122803] The buggy address belongs to the physical page:
[   23.123104] page:0000000072ac19f0 refcount:1 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x24a09
[   23.123609] flags: 0xfffffc0001000(reserved|node=0|zone=1|lastcpupid=0x1fffff)
[   23.123998] page_type: 0xffffffff()
[   23.124194] raw: 000fffffc0001000 ffffea0000928248 ffffea0000928248 0000000000000000
[   23.124610] raw: 0000000000000000 0000000000000000 00000001ffffffff 0000000000000000
[   23.125023] page dumped because: kasan: bad access detected
[   23.125326]
[   23.125421] Memory state around the buggy address:
[   23.125682]  ffffc90000007800: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[   23.126072]  ffffc90000007880: 00 00 00 00 00 f1 f1 f1 f1 f1 f1 00 00 f2 f2 00
[   23.126455] >ffffc90000007900: 00 00 00 00 00 00 00 00 00 f2 f2 f2 f2 00 00 00
[   23.126840]                                               ^
[   23.127138]  ffffc90000007980: 00 00 00 00 00 00 00 00 00 00 00 00 00 f3 f3 f3
[   23.127522]  ffffc90000007a00: f3 00 00 00 00 00 00 00 00 00 00 00 f1 f1 f1 f1
[   23.127906] ==================================================================
[   23.128324] Disabling lock debugging due to kernel taint

Using simple s16 pointers for the 16-bit accesses fixes the problem. For
the 32-bit accesses, src and dst can be used directly.

Fixes: 96518518cc41 ("netfilter: add nftables")
Cc: stable@vger.kernel.org
Reported-by: Tanguy DUBROCA (@SidewayRE) from @Synacktiv working with ZDI
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Reviewed-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

netfilter: nf_tables: do not ignore genmask when looking up chain by id

commit 515ad530795c118f012539ed76d02bacfd426d89 upstream.

When adding a rule to a chain referring to its ID, if that chain had been
deleted on the same batch, the rule might end up referring to a deleted
chain.

This will lead to a WARNING like following:

[   33.098431] ------------[ cut here ]------------
[   33.098678] WARNING: CPU: 5 PID: 69 at net/netfilter/nf_tables_api.c:2037 nf_tables_chain_destroy+0x23d/0x260
[   33.099217] Modules linked in:
[   33.099388] CPU: 5 PID: 69 Comm: kworker/5:1 Not tainted 6.4.0+ #409
[   33.099726] Workqueue: events nf_tables_trans_destroy_work
[   33.100018] RIP: 0010:nf_tables_chain_destroy+0x23d/0x260
[   33.100306] Code: 8b 7c 24 68 e8 64 9c ed fe 4c 89 e7 e8 5c 9c ed fe 48 83 c4 08 5b 41 5c 41 5d 41 5e 41 5f 5d 31 c0 89 c6 89 c7 c3 cc cc cc cc <0f> 0b 48 83 c4 08 5b 41 5c 41 5d 41 5e 41 5f 5d 31 c0 89 c6 89 c7
[   33.101271] RSP: 0018:ffffc900004ffc48 EFLAGS: 00010202
[   33.101546] RAX: 0000000000000001 RBX: ffff888006fc0a28 RCX: 0000000000000000
[   33.101920] RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000000000000
[   33.102649] RBP: ffffc900004ffc78 R08: 0000000000000000 R09: 0000000000000000
[   33.103018] R10: 0000000000000000 R11: 0000000000000000 R12: ffff8880135ef500
[   33.103385] R13: 0000000000000000 R14: dead000000000122 R15: ffff888006fc0a10
[   33.103762] FS:  0000000000000000(0000) GS:ffff888024c80000(0000) knlGS:0000000000000000
[   33.104184] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[   33.104493] CR2: 00007fe863b56a50 CR3: 00000000124b0001 CR4: 0000000000770ee0
[   33.104872] PKRU: 55555554
[   33.104999] Call Trace:
[   33.105113]  <TASK>
[   33.105214]  ? show_regs+0x72/0x90
[   33.105371]  ? __warn+0xa5/0x210
[   33.105520]  ? nf_tables_chain_destroy+0x23d/0x260
[   33.105732]  ? report_bug+0x1f2/0x200
[   33.105902]  ? handle_bug+0x46/0x90
[   33.106546]  ? exc_invalid_op+0x19/0x50
[   33.106762]  ? asm_exc_invalid_op+0x1b/0x20
[   33.106995]  ? nf_tables_chain_destroy+0x23d/0x260
[   33.107249]  ? nf_tables_chain_destroy+0x30/0x260
[   33.107506]  nf_tables_trans_destroy_work+0x669/0x680
[   33.107782]  ? mark_held_locks+0x28/0xa0
[   33.107996]  ? __pfx_nf_tables_trans_destroy_work+0x10/0x10
[   33.108294]  ? _raw_spin_unlock_irq+0x28/0x70
[   33.108538]  process_one_work+0x68c/0xb70
[   33.108755]  ? lock_acquire+0x17f/0x420
[   33.108977]  ? __pfx_process_one_work+0x10/0x10
[   33.109218]  ? do_raw_spin_lock+0x128/0x1d0
[   33.109435]  ? _raw_spin_lock_irq+0x71/0x80
[   33.109634]  worker_thread+0x2bd/0x700
[   33.109817]  ? __pfx_worker_thread+0x10/0x10
[   33.110254]  kthread+0x18b/0x1d0
[   33.110410]  ? __pfx_kthread+0x10/0x10
[   33.110581]  ret_from_fork+0x29/0x50
[   33.110757]  </TASK>
[   33.110866] irq event stamp: 1651
[   33.111017] hardirqs last  enabled at (1659): [<ffffffffa206a209>] __up_console_sem+0x79/0xa0
[   33.111379] hardirqs last disabled at (1666): [<ffffffffa206a1ee>] __up_console_sem+0x5e/0xa0
[   33.111740] softirqs last  enabled at (1616): [<ffffffffa1f5d40e>] __irq_exit_rcu+0x9e/0xe0
[   33.112094] softirqs last disabled at (1367): [<ffffffffa1f5d40e>] __irq_exit_rcu+0x9e/0xe0
[   33.112453] ---[ end trace 0000000000000000 ]---

This is due to the nft_chain_lookup_byid ignoring the genmask. After this
change, adding the new rule will fail as it will not find the chain.

Fixes: 837830a4b439 ("netfilter: nf_tables: add NFTA_RULE_CHAIN_ID attribute")
Cc: stable@vger.kernel.org
Reported-by: Mingi Cho of Theori working with ZDI
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Reviewed-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

netfilter: conntrack: Avoid nf_ct_helper_hash uses after free

commit 6eef7a2b933885a17679eb8ed0796ddf0ee5309b upstream.

If nf_conntrack_init_start() fails (for example due to a
register_nf_conntrack_bpf() failure), the nf_conntrack_helper_fini()
clean-up path frees the nf_ct_helper_hash map.

When built with NF_CONNTRACK=y, further netfilter modules (e.g:
netfilter_conntrack_ftp) can still be loaded and call
nf_conntrack_helpers_register(), independently of whether nf_conntrack
initialized correctly. This accesses the nf_ct_helper_hash dangling
pointer and causes a uaf, possibly leading to random memory corruption.

This patch guards nf_conntrack_helper_register() from accessing a freed
or uninitialized nf_ct_helper_hash pointer and fixes possible
uses-after-free when loading a conntrack module.

Cc: stable@vger.kernel.org
Fixes: 12f7a505331e ("netfilter: add user-space connection tracking helper infrastructure")
Signed-off-by: Florent Revest <revest@chromium.org>
Reviewed-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

netfilter: nf_tables: unbind non-anonymous set if rule construction fails

commit 3e70489721b6c870252c9082c496703677240f53 upstream.

Otherwise a dangling reference to a rule object that is gone remains
in the set binding list.

Fixes: 26b5a5712eb8 ("netfilter: nf_tables: add NFT_TRANS_PREPARE_ERROR to deal with bound set/chain")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mtd: parsers: refer to ARCH_BCMBCA instead of ARCH_BCM4908

commit 085679b15b5af65f9610f619afde41da0f966194 upstream.

Commit dd5c672d7ca9 ("arm64: bcmbca: Merge ARCH_BCM4908 to ARCH_BCMBCA")
removes config ARCH_BCM4908 as config ARCH_BCMBCA has the same intent.

Probably due to concurrent development, commit 002181f5b150 ("mtd: parsers:
add Broadcom's U-Boot parser") introduces 'Broadcom's U-Boot partition
parser' that depends on ARCH_BCM4908, but this use was not visible during
the config refactoring from the commit above. Hence, these two changes
create a reference to a non-existing config symbol.

Adjust the MTD_BRCM_U_BOOT definition to refer to ARCH_BCMBCA instead of
ARCH_BCM4908 to remove the reference to the non-existing config symbol
ARCH_BCM4908.

Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20221116124932.4748-1-lukas.bulwahn@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/i915/tc: Fix system resume MST mode restore for DP-alt sinks

commit 06f66261a1567d66b9d35c87393b6edfbea4c8f8 upstream.

At least restoring the MST topology during system resume needs to use
AUX before the display HW readout->sanitization sequence is complete,
but on TC ports the PHY may be in the wrong mode for this, resulting in
the AUX transfers to fail.

The initial TC port mode is kept fixed as BIOS left it for the above HW
readout sequence (to prevent changing the mode on an enabled port). If
the port is disabled this initial mode is TBT - as in any case the PHY
ownership is not held - even if a DP-alt sink is connected. Thus, the
AUX transfers during this time will use TBT mode instead of the expected
DP-alt mode and so time out.

Fix the above by connecting the PHY during port initialization if the
port is disabled, which will switch to the expected mode (DP-alt in the
above case).

As the encoder/pipe HW state isn't read-out yet at this point, check if
the port is enabled based on the DDI_BUF enabled flag. Save the read-out
initial mode, so intel_tc_port_sanitize_mode() can check this wrt. the
read-out encoder HW state.

Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230316131724.359612-5-imre.deak@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/i915/tc: Fix TC port link ref init for DP MST during HW readout

commit 67165722c27cc46de112a4e10b450170c8980a6f upstream.

An enabled TC MST port holds one TC port link reference, regardless of
the number of enabled streams on it, but the TC port HW readout takes
one reference for each active MST stream.

Fix the HW readout, taking only one reference for MST ports.

This didn't cause an actual problem, since the encoder HW readout doesn't
yet support reading out the MST HW state.

Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Reviewed-by: Andrzej Hajda <andrzej.hajda@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230316131724.359612-3-imre.deak@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/i915: Fix TypeC mode initialization during system resume

commit a82796a2e332d108b2d3aff38509caad370f69b5 upstream.

During system resume DP MST requires AUX to be working already before
the HW state readout of the given encoder. Since AUX requires the
encoder/PHY TypeC mode to be initialized, which atm only happens during
HW state readout, these AUX transfers can change the TypeC mode
incorrectly (disconnecting the PHY for an enabled encoder) and trigger
the state check WARNs in intel_tc_port_sanitize().

Fix this by initializing the TypeC mode earlier both during driver
loading and system resume and making sure that the mode can't change
until the encoder's state is read out. While at it add the missing
DocBook comments and rename
intel_tc_port_sanitize()->intel_tc_port_sanitize_mode() for consistency.

Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220922172148.2913088-1-imre.deak@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mm/mmap: Fix extra maple tree write

based on commit 0503ea8f5ba73eb3ab13a81c1eefbaf51405385a upstream.

This was inadvertently fixed during the removal of __vma_adjust().

When __vma_adjust() is adjusting next with a negative value (pushing
vma->vm_end lower), there would be two writes to the maple tree.  The
first write is unnecessary and uses all allocated nodes in the maple
state.  The second write is necessary but will need to allocate nodes
since the first write has used the allocated nodes.  This may be a
problem as it may not be safe to allocate at this time, such as a low
memory situation.  Fix the issue by avoiding the first write and only
write the adjusted "next" VMA.

Reported-by: John Hsu <John.Hsu@mediatek.com>
Link: https://lore.kernel.org/lkml/9cb8c599b1d7f9c1c300d1a334d5eb70ec4d7357.camel@mediatek.com/
Cc: stable@vger.kernel.org
Cc: linux-mm@kvack.org
Signed-off-by: Liam R. Howlett <Liam.Howlett@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

xfs: fix xfs_inodegc_stop racing with mod_delayed_work

commit 2254a7396a0ca6309854948ee1c0a33fa4268cec upstream.

syzbot reported this warning from the faux inodegc shrinker that tries
to kick off inodegc work:

------------[ cut here ]------------
WARNING: CPU: 1 PID: 102 at kernel/workqueue.c:1445 __queue_work+0xd44/0x1120 kernel/workqueue.c:1444
RIP: 0010:__queue_work+0xd44/0x1120 kernel/workqueue.c:1444
Call Trace:
__queue_delayed_work+0x1c8/0x270 kernel/workqueue.c:1672
mod_delayed_work_on+0xe1/0x220 kernel/workqueue.c:1746
xfs_inodegc_shrinker_scan fs/xfs/xfs_icache.c:2212 [inline]
xfs_inodegc_shrinker_scan+0x250/0x4f0 fs/xfs/xfs_icache.c:2191
do_shrink_slab+0x428/0xaa0 mm/vmscan.c:853
shrink_slab+0x175/0x660 mm/vmscan.c:1013
shrink_one+0x502/0x810 mm/vmscan.c:5343
shrink_many mm/vmscan.c:5394 [inline]
lru_gen_shrink_node mm/vmscan.c:5511 [inline]
shrink_node+0x2064/0x35f0 mm/vmscan.c:6459
kswapd_shrink_node mm/vmscan.c:7262 [inline]
balance_pgdat+0xa02/0x1ac0 mm/vmscan.c:7452
kswapd+0x677/0xd60 mm/vmscan.c:7712
kthread+0x2e8/0x3a0 kernel/kthread.c:376
ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:308

This warning corresponds to this code in __queue_work:

/*
* For a draining wq, only works from the same workqueue are
* allowed. The __WQ_DESTROYING helps to spot the issue that
* queues a new work item to a wq after destroy_workqueue(wq).
*/
if (unlikely(wq->flags & (__WQ_DESTROYING | __WQ_DRAINING) &&
     WARN_ON_ONCE(!is_chained_work(wq))))
return;

For this to trip, we must have a thread draining the inodedgc workqueue
and a second thread trying to queue inodegc work to that workqueue.
This can happen if freezing or a ro remount race with reclaim poking our
faux inodegc shrinker and another thread dropping an unlinked O_RDONLY
file:

Thread 0 Thread 1 Thread 2

xfs_inodegc_stop

xfs_inodegc_shrinker_scan
xfs_is_inodegc_enabled
<yes, will continue>

xfs_clear_inodegc_enabled
xfs_inodegc_queue_all
<list empty, do not queue inodegc worker>

xfs_inodegc_queue
<add to list>
xfs_is_inodegc_enabled
<no, returns>

drain_workqueue
<set WQ_DRAINING>

llist_empty
<no, will queue list>
mod_delayed_work_on(..., 0)
__queue_work
<sees WQ_DRAINING, kaboom>

In other words, everything between the access to inodegc_enabled state
and the decision to poke the inodegc workqueue requires some kind of
coordination to avoid the WQ_DRAINING state.  We could perhaps introduce
a lock here, but we could also try to eliminate WQ_DRAINING from the
picture.

We could replace the drain_workqueue call with a loop that flushes the
workqueue and queues workers as long as there is at least one inode
present in the per-cpu inodegc llists.  We've disabled inodegc at this
point, so we know that the number of queued inodes will eventually hit
zero as long as xfs_inodegc_start cannot reactivate the workers.

There are four callers of xfs_inodegc_start.  Three of them come from the
VFS with s_umount held: filesystem thawing, failed filesystem freezing,
and the rw remount transition.  The fourth caller is mounting rw (no
remount or freezing possible).

There are three callers ofs xfs_inodegc_stop.  One is unmounting (no
remount or thaw possible).  Two of them come from the VFS with s_umount
held: fs freezing and ro remount transition.

Hence, it is correct to replace the drain_workqueue call with a loop
that drains the inodegc llists.

Fixes: 6191cf3ad59f ("xfs: flush inodegc workqueue tasks before cancel")
Signed-off-by: Darrick J. Wong <djwong@kernel.org>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Acked-by: Darrick J. Wong <djwong@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>