Jingoo Han [Fri, 22 Feb 2013 00:45:39 +0000 (16:45 -0800)]
rtc: rtc-lp8788: use devm_request_threaded_irq()
Use devm_request_threaded_irq() to make cleanup paths more simple.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jingoo Han [Fri, 22 Feb 2013 00:45:38 +0000 (16:45 -0800)]
rtc: rtc-coh901331: use devm_clk_get()
Use devm_clk_get() to make cleanup paths more simple.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jingoo Han [Fri, 22 Feb 2013 00:45:37 +0000 (16:45 -0800)]
rtc: rtc-vt8500: use devm_*() functions
Use devm_*() functions to make cleanup paths more simple.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jingoo Han [Fri, 22 Feb 2013 00:45:36 +0000 (16:45 -0800)]
rtc: rtc-tps6586x: use devm_request_threaded_irq()
Use devm_request_threaded_irq() to make cleanup paths more simple.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jingoo Han [Fri, 22 Feb 2013 00:45:35 +0000 (16:45 -0800)]
rtc: rtc-imxdi: use devm_clk_get()
Use devm_clk_get() to make cleanup paths more simple.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jingoo Han [Fri, 22 Feb 2013 00:45:34 +0000 (16:45 -0800)]
rtc: rtc-cmos: use dev_warn()/dev_dbg() instead of printk()/pr_debug()
Fix the checkpatch warning as below:
WARNING: Prefer netdev_err(netdev, ... then dev_err(dev, ... then pr_err(... to printk(KERN_ERR ...
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jingoo Han [Fri, 22 Feb 2013 00:45:33 +0000 (16:45 -0800)]
rtc: rtc-pcf8583: use dev_warn() instead of printk()
Fix the checkpatch warning as below:
WARNING: Prefer netdev_err(netdev, ... then dev_err(dev, ... then pr_err(... to printk(KERN_ERR ...
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jingoo Han [Fri, 22 Feb 2013 00:45:32 +0000 (16:45 -0800)]
rtc: rtc-sun4v: use pr_warn() instead of printk()
Fix the checkpatch warning as below:
WARNING: Prefer netdev_err(netdev, ... then dev_err(dev, ... then pr_err(... to printk(KERN_ERR ...
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jingoo Han [Fri, 22 Feb 2013 00:45:30 +0000 (16:45 -0800)]
rtc: rtc-vr41xx: use dev_info() instead of printk()
Fix the checkpatch warning as below:
WARNING: Prefer netdev_err(netdev, ... then dev_err(dev, ... then pr_err(... to printk(KERN_ERR ...
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jingoo Han [Fri, 22 Feb 2013 00:45:29 +0000 (16:45 -0800)]
rtc: rtc-rs5c313: use pr_err() instead of printk()
Fix the checkpatch warning as below:
WARNING: Prefer netdev_err(netdev, ... then dev_err(dev, ... then pr_err(... to printk(KERN_ERR ...
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jingoo Han [Fri, 22 Feb 2013 00:45:28 +0000 (16:45 -0800)]
rtc: rtc-at91rm9200: use dev_dbg()/dev_err() instead of printk()/pr_debug()
Fix the checkpatch warning as below:
WARNING: Prefer netdev_err(netdev, ... then dev_err(dev, ... then pr_err(... to printk(KERN_ERR ...
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jingoo Han [Fri, 22 Feb 2013 00:45:27 +0000 (16:45 -0800)]
rtc: rtc-rs5c372: use dev_dbg()/dev_warn() instead of printk()/pr_debug()
Fix the checkpatch warning as below:
WARNING: Prefer netdev_err(netdev, ... then dev_err(dev, ... then pr_err(... to printk(KERN_ERR ...
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jingoo Han [Fri, 22 Feb 2013 00:45:26 +0000 (16:45 -0800)]
rtc: rtc-ds2404: use dev_err() instead of printk()
Fix the checkpatch warning as below:
WARNING: Prefer netdev_err(netdev, ... then dev_err(dev, ... then pr_err(... to printk(KERN_ERR ...
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jingoo Han [Fri, 22 Feb 2013 00:45:25 +0000 (16:45 -0800)]
rtc: rtc-efi: use dev_err()/dev_warn()/pr_err() instead of printk()
Fix the checkpatch warnings as below:
WARNING: Prefer netdev_err(netdev, ... then dev_err(dev, ... then pr_err(... to printk(KERN_ERR ...
WARNING: please, no space before tabs
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jingoo Han [Fri, 22 Feb 2013 00:45:24 +0000 (16:45 -0800)]
rtc: max77686: use dev_info() instead of printk()
Fix the checkpatch warning as below:
WARNING: Prefer netdev_err(netdev, ... then dev_err(dev, ... then pr_err(... to printk(KERN_ERR ...
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jingoo Han [Fri, 22 Feb 2013 00:45:23 +0000 (16:45 -0800)]
rtc: use dev_warn()/dev_dbg()/pr_err() instead of printk()
Fix the checkpatch warning as below:
WARNING: Prefer netdev_err(netdev, ... then dev_err(dev, ... then pr_err(... to printk(KERN_ERR ...
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Chao Xie [Fri, 22 Feb 2013 00:45:17 +0000 (16:45 -0800)]
drivers/rtc/rtc-sa1100.c: move clock enable/disable to probe/remove
The original sa1100_rtc_open/sa1100_rtc_release will be called when the
/dev/rtc0 is opened or closed. In fact, these two functions will
enable/disable the clock. Disabling clock will make rtc not work. So
only enable/disable clock when probe/remove the device.
Signed-off-by: Chao Xie <chao.xie@marvell.com>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Leo Song <liangs@marvell.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jonghwa Lee [Fri, 22 Feb 2013 00:45:07 +0000 (16:45 -0800)]
rtc: max8997: add driver for max8997 rtc
Add an rtc driver for Maxim 8997 multifunction chip. Max8997 has rtc
module in it. and it can be used for timekeeping clock and system alarm.
It provide various operational mode those are BCD/binary, 24/12hour,
am/pm. Driver sets binary/24/ for default. Maxim 8997 also supports
SMPL(Sudden Momentary Power Loss), WTSR (Watchdog Timeout and Software
Reset).
Signed-off-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Cc: Devendra Naga <devendra.aaru@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jingoo Han [Fri, 22 Feb 2013 00:45:06 +0000 (16:45 -0800)]
drivers/rtc/rtc-s3c.c: use dev_dbg() instaed of pr_debug()
Use dev_dbg() instaed of pr_debug() to be consistent.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Gregory CLEMENT [Fri, 22 Feb 2013 00:44:55 +0000 (16:44 -0800)]
arm: mvebu: add RTC support for Armada 370 and Armada XP
The Armada 370 and Armada XP Socs have the same controller that the one
used in the orion platforms. This patch updates the device tree for
these SoCs.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Rob Herring [Fri, 22 Feb 2013 00:44:54 +0000 (16:44 -0800)]
drivers/rtc/rtc-pl031.c: add wakeup support
Mark the pl031 as wake-up capable so that rtcwake and suspend test can work.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Torben Hohn [Fri, 22 Feb 2013 00:44:40 +0000 (16:44 -0800)]
rtc: add support for spi rtc rx4581
[akpm@linux-foundation.org: checkpatch fixes]
Signed-off-by: Torben Hohn <torbenh@linutronix.de>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Laxman Dewangan [Fri, 22 Feb 2013 00:44:38 +0000 (16:44 -0800)]
drivers/rtc/rtc-tps65910.c: set irq flag to IRQF_EARLY_RESUME during irq request
All interrupt get disabled during system suspend and enabled during system
resume. The enabling/disabling of interrupt happen in sequence of
interrupt registration with framework.
Therefore, in resume, the parent interrupt of this device enabled before
the RTC irq interrupt enabled. If RTC is enabled for alarm wake and if
system wake by alarm then there is interrupt pending for RTC. In resume,
the parent interrupt get enabled before the rtc interrupt and hence ISR
get served. In ISR, it founds that rtc interrupt is disabled and so it
does not call the rtc isr handler and hence it misses the interrupt.
Setting flag for early resume so that rtc interrupt get enabled before
parent interrupt and so rtc interrupt get enabled when parent interrupt
handler check for interrupt of device and call the rtc handler if it is
there. This way it will not miss the interrupt.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Laxman Dewangan [Fri, 22 Feb 2013 00:44:37 +0000 (16:44 -0800)]
drivers/rtc/rtc-tps65910.c: use sleep_pm_ops macro for initialising suspend/resume callbacks
Use SET_SYSTEM_SLEEP_PM_OPS for setting suspend/resume callbacks for
dev_pm_ops.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Laxman Dewangan [Fri, 22 Feb 2013 00:44:36 +0000 (16:44 -0800)]
drivers/rtc/rtc-tps65910.c: remove unnecessary irq stat save and restore
The driver stores the interrupt enable register before going to suspend
and restore in resume. Also it enables alarm before going to suspend.
The driver only write the Interrupt enable register for enabling ALARM and
does not enable any other bits. So it is not require to save complete
register and enable ALARM interrupt before suspend and restore in resume.
Also ALARM interrupt already enable if alarm is enabled before going to
suspend and hence it is not require to enable explictly in suspend.
Removing such above code.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Laxman Dewangan [Fri, 22 Feb 2013 00:44:35 +0000 (16:44 -0800)]
drivers/rtc/rtc-tps65910.c: enable/disable wake in suspend/resume
Making the rtc driver as wakeup capabale and leaving the wake
enable/disable decision to user space through a sysfs attribute.
In suspend, enable wake if device wakeup enabled. In resume disable wake
again.
This change is inline with the Documentation/power/devices.txt#
/sys/devices/.../power/wakeup files
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Laxman Dewangan [Fri, 22 Feb 2013 00:44:34 +0000 (16:44 -0800)]
rtc: add RTC driver for TPS80031/TPS80032
Add an RTC driver for TPS80031/TPS80032 chips by TI. This driver
supports:
- Setting and getting time and date.
- Setting and reading alarm time.
- Alarm and interrupt functionlity.
[akpm@linux-foundation.org: remove obsolete __devinit/__devexit]
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Reviewed-by: Devendra Naga <devendra.aaru@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Kim, Milo [Fri, 22 Feb 2013 00:44:32 +0000 (16:44 -0800)]
rtc: add new lp8788 rtc driver
TI LP8788 PMU supports regulators, battery charger, RTC, ADC, backlight
driver and current sinks. This patch enables LP8788 rtc module.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Cc: "devendra.aaru" <devendra.aaru@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Srinivas Kandagatla [Fri, 22 Feb 2013 00:44:31 +0000 (16:44 -0800)]
drivers/rtc/rtc-ds2404.c: use module_platform_driver macro
Remove removes some code duplication by using module_platform_driver().
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Peter Senna Tschudin [Fri, 22 Feb 2013 00:44:30 +0000 (16:44 -0800)]
drivers/rtc: remove unnecessary semicolons
Found by Coccinelle: http://coccinelle.lip6.fr/
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Haojian Zhuang [Fri, 22 Feb 2013 00:44:29 +0000 (16:44 -0800)]
drivers/rtc/rtc-pxa.c: avoid cpuid checking
pxa-rtc is widely used in pxa27x/pxa3xx/pxa93x/pxa95x. Checking cpuid in
pxa-rtc driver is unnecessary since we assign on-chip device in soc files.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Sachin Kamat [Fri, 22 Feb 2013 00:44:28 +0000 (16:44 -0800)]
drivers/rtc: use of_match_ptr() macro
This eliminates having an #ifdef returning NULL for the case when OF is
disabled. Maintains consistency in cases where OF is always selected.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jesper Nilsson [Fri, 22 Feb 2013 00:44:27 +0000 (16:44 -0800)]
rtc-pcf8523: add low battery voltage support
Implement reading of the battery voltage low signal for rtc-pcf8523.
The bit is read-only and cannot be cleared by software, so no
clear function is implemented.
[akpm@linux-foundation.org: omit pcf8563_rtc_ioctl() if CONFIG_RTC_INTF_DEV=n]
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
Reviewed-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jonghwa Lee [Fri, 22 Feb 2013 00:44:26 +0000 (16:44 -0800)]
rtc: max77686: add Maxim 77686 driver
Add a driver to support max77686 rtc. MAX77686 rtc support smpl and wtsr
mode. It has two alarm register which can be used for alarming to wake
system up. This drvier uses regmap to access its register.
[akpm@linux-foundation.org: remove inline, __devinit annotations]
[jg1.han@samsung.com: fix build warnings]
[akpm@linux-foundation.org: simplify code]
Signed-off-by: Chiwoong Byun <woong.byun@samsung.com>
Signed-off-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Signed-off-by: Myugnjoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Leo Song [Fri, 22 Feb 2013 00:44:24 +0000 (16:44 -0800)]
drivers/rtc/rtc-pxa.c: fix alarm can't wake up system issue
Fix alarm can't wake up system issue
Signed-off-by: Leo Song <liangs@marvell.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Leo Song [Fri, 22 Feb 2013 00:44:23 +0000 (16:44 -0800)]
drivers/rtc/rtc-pxa.c: fix alarm not match issue
Fix pxa rtc alarm issue by setting week of month and day of week in
rdar/rdcr or it would not match.
Signed-off-by: Leo Song <liangs@marvell.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andy Shevchenko [Fri, 22 Feb 2013 00:44:22 +0000 (16:44 -0800)]
drivers/rtc: dump small buffers via %*ph
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Yuanhan Liu [Fri, 22 Feb 2013 00:44:21 +0000 (16:44 -0800)]
kernel/nsproxy.c: remove duplicate task_cred_xxx for user_ns
We can use user_ns, which is also assigned from task_cred_xxx(tsk,
user_ns), at the beginning of copy_namespaces().
Signed-off-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Acked-by: Serge Hallyn <serge.hallyn@canonical.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Zhang Yanfei [Fri, 22 Feb 2013 00:44:20 +0000 (16:44 -0800)]
binfmt_elf: remove unused argument in fill_elf_header
In fill_elf_header(), elf->e_ident[EI_OSABI] is always set to ELF_OSABI,
so remove the unused argument 'osabi'.
Signed-off-by: Zhang Yanfei <zhangyanfei@cn.fujitsu.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Bruce Allan [Fri, 22 Feb 2013 00:44:19 +0000 (16:44 -0800)]
checkpatch: fix USLEEP_RANGE test
Do not test udelay() for a value less than 10usec when passed a variable
instead of a hard-coded number; there is no way for checkpatch to know the
value of the variable. As it is today, it will complain about variables
with alphanumeric characters plus '_', e.g. foo_bar, but not variables
with other characters, eg. foo->bar.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Cc: Andy Whitcroft <apw@canonical.com>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Joe Perches [Fri, 22 Feb 2013 00:44:18 +0000 (16:44 -0800)]
checkpatch: Add check for kcalloc argument order
kcalloc is sometimes misused with the first and second arguments switched.
Same issue with kmalloc_array too.
Bleat if sizeof is the first argument
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Joe Perches [Fri, 22 Feb 2013 00:44:17 +0000 (16:44 -0800)]
checkpatch: don't emit the CamelCase warning for PageFoo
I'm getting a ton of these:
WARNING: Avoid CamelCase: <PageTransHuge>
#140: FILE: mm/migrate.c:1576:
+ if (PageTransHuge(page) && page_count(page) != 3) {
So exclude anything which starts with "Page".
Tested-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Joe Perches [Fri, 22 Feb 2013 00:44:15 +0000 (16:44 -0800)]
checkpatch: add Joe to MAINTAINERS
Signed-off-by: Joe Perches <joe@perches.com>
Cc: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Joe Perches [Fri, 22 Feb 2013 00:44:14 +0000 (16:44 -0800)]
checkpatch: warn on unnecessary __dev<foo> section markings
Get people to stop adding __devinit and __devexit section markings.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Andy Whitcroft <apw@canonical.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Joe Perches [Fri, 22 Feb 2013 00:44:13 +0000 (16:44 -0800)]
checkpatch: prefer dev_<level>( to dev_printk(KERN_<LEVEL>
Add YA check to printk style.
dev_<level> uses are functions and generate smaller
object code than dev_printk(KERN_<LEVEL>.
Signed-off-by: Joe Perches <joe@perches.com>
Cc: Andy Whitcroft <apw@canonical.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Florian Fainelli [Fri, 22 Feb 2013 00:44:12 +0000 (16:44 -0800)]
decompressors: make the default XZ_DEC_* config match the selected architecture
Change the defautl XZ_DEC_* config symbol to match the configured
architecture. It is perfectly legitimate to support multiple XZ BCJ
filters for different architectures (e.g.: to mount foreign squashfs/xz
compressed filesystems), it is however more natural not to select them all
by default, but only the one matching the configured architecture.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Acked-by: Lasse Collin <lasse.collin@tukaani.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Florian Fainelli [Fri, 22 Feb 2013 00:44:11 +0000 (16:44 -0800)]
decompressors: drop dependency on CONFIG_EXPERT
Remove the XZ_DEC_* depedencey on CONFIG_EXPERT as recommended by Lasse
Colin.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Acked-by: Lasse Collin <lasse.collin@tukaani.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Florian Fainelli [Fri, 22 Feb 2013 00:44:10 +0000 (16:44 -0800)]
decompressors: group XZ_DEC_* symbols under an if XZ_BCJ / endif
Group all architecture-specific BCJ filter configuration symbols under an
if XZ_BCJ / endif statement.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Acked-by: Lasse Collin <lasse.collin@tukaani.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Namjae Jeon [Fri, 22 Feb 2013 00:44:08 +0000 (16:44 -0800)]
lib/parser.c: fix up comments for valid return values from match_number
match_number() has return values of -ENOMEM, -EINVAL and -ERANGE. So, for
all the functions calling match_number, the return value should include
these values. Fix up the comments to reflect the correct values.
Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Amit Sahrawat <a.sahrawat@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Kim, Milo [Fri, 22 Feb 2013 00:44:07 +0000 (16:44 -0800)]
backlight: lp855x_bl: simplify bl_get_brightness()
Getting the brightness value is not critical, no need to read the actual
register value. To simplify it, just return the 'bl->props.brightness'
value. Then, lp855x_read_byte() can be removed, not used any more.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Kim, Milo [Fri, 22 Feb 2013 00:44:06 +0000 (16:44 -0800)]
backlight: lp855x_bl: support new LP8557 device
LP8557 is one of LP855x family device, but it has different register map
and initialization process. To support this device, device specific
configuration is done through the lp855x_device_config structure.
Few register definitions are fixed for better readability.
BRIGHTNESS_CTRL -> LP855X_BRIGHTNESS_CTRL
DEVICE_CTRL -> LP855X_DEVICE_CTRL
EEPROM_START -> LP855X_EEPROM_START
EEPROM_END -> LP855X_EEPROM_END
EPROM_START -> LP8556_EPROM_START
EPROM_END -> LP8556_EPROM_END
And LP8557 register definitions are added. New register function,
lp855x_update_bit() is added.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Kim, Milo [Fri, 22 Feb 2013 00:44:05 +0000 (16:44 -0800)]
backlight: lp855x_bl: introduce device configuration flow
At this moment, LP855x device driver has fixed register configuration.
For example, fixed register addresses and values are set on the device
initialization. But new device of LP855x family, LP8557 has different
register map and initialization sequence. To support new device
architecture, initialization process should be changed.
Introduce new structure: lp855x_device_config
=============================================
With lp855x_device_config, device specific features are configurable.
Use configurable function calls and register addresses rather than fixed values.
Change on device initialization
===============================
In old LP855x driver architecture, the device initialization was simple.
- Just update the brightness/device control register/ROM area(optional).
In new LP855x driver architecture, two more works are added - pre_init and
post_init.
Those init functions are optional, used for new device LP8557.
New device initialization flow: generic sequence
=================================================
1) pre_init_device()
2) update the brightness register
3) update the device control register
4) update ROM area if need
5) post_init_device()
Name change
===========
Use generic name 'lp855x_configure()' instead of 'lp855x_init_registers()'.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Lars-Peter Clausen [Fri, 22 Feb 2013 00:44:04 +0000 (16:44 -0800)]
drivers/video/backlight/adp88?0_bl.c: fix resume
Clearing the NSTBY bit in the control register also automatically clears
the BLEN bit. So we need to make sure to set it again during resume,
otherwise the backlight will stay off.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jingoo Han [Fri, 22 Feb 2013 00:44:02 +0000 (16:44 -0800)]
drivers/video/backlight/lm3630_bl.c: remove ret = -EIO of lm3630_backlight_register()
There is no need to return -EIO, because backlight_device_register()
already returns correct error values.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Daniel Jeong <daniel.jeong@ti.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dan Carpenter [Fri, 22 Feb 2013 00:44:01 +0000 (16:44 -0800)]
drivers/video/backlight/s6e63m0.c: report ->gamma_table_count correctly
gamma_table has 3 arrays which each hold MAX_GAMMA_LEVEL pointers to int.
The current code sets ->gamma_table_count to 6 on 64bit arches and to 3 on
32 bit arches. It should be 3 on everything.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Jingoo Han <jg1.han@samsung.com>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Axel Lin [Fri, 22 Feb 2013 00:44:00 +0000 (16:44 -0800)]
drivers/video/backlight/88pm860x_bl.c: add missing of_node_put()
of_find_node_by_name() returns a node pointer with refcount incremented,
use of_node_put() on it when done.
of_find_node_by_name() will call of_node_put() against the node pass to
from parameter, thus we also need to call of_node_get(from) before calling
of_find_node_by_name().
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Cc: Jingoo Han <jg1.han@samsung.com>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Guennadi Liakhovetski [Fri, 22 Feb 2013 00:43:59 +0000 (16:43 -0800)]
backlight: add an AS3711 PMIC backlight driver
This is an initial commit of a backlight driver, using step-up DCDC
power supplies on AS3711 PMIC. Only one mode has actually been tested,
several further modes have been implemented "dry," but disabled to avoid
accidental hardware damage. Anyone wishing to use any of those modes
will have to modify the driver.
Tested on sh73a0-based kzm9g board. Only one mode has been tested and
is enabled. That mode copies the sample code from the manufacturer.
Deviations from that code proved to be fatal for the hardware...
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: Magnus Damm <magnus.damm@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andrew Morton [Fri, 22 Feb 2013 00:43:57 +0000 (16:43 -0800)]
drivers/video/backlight/Makefile: cleanup
Fix up indenting. Also alphasort all entries, which reduces patch
collisions.
Cc: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Maxime Ripard [Fri, 22 Feb 2013 00:43:56 +0000 (16:43 -0800)]
fb: backlight: add the Himax HX-8357B LCD controller
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Jingoo Han <jg1.han@samsung.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Brian Lilly <brian@crystalfontz.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Sachin Kamat [Fri, 22 Feb 2013 00:43:55 +0000 (16:43 -0800)]
drivers/video/backlight/ld9040.c: use devm_regulator_bulk_get() API
devm_regulator_bulk_get is device managed and saves some cleanup
and exit code.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Donghwa Lee <dh09.lee@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Axel Lin [Fri, 22 Feb 2013 00:43:53 +0000 (16:43 -0800)]
drivers/video/backlight/l4f00242t03.c: convert to devm_regulator_get()
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Cc: Alberto Panizzo <maramaopercheseimorto@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Devendra Naga [Fri, 22 Feb 2013 00:43:52 +0000 (16:43 -0800)]
drivers/video/backlight/lm3639_bl.c: remove ret = -EIO at error paths of probe
The APIs are returning correctly the err codes, no need to assign -EIO
to the ret again.
Signed-off-by: Devendra Naga <devendra.aaru@gmail.com>
Acked-by: Daniel Jeong <daniel.jeong@ti.com>
Cc: G.Shark Jeong <gshark.jeong@gmail.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jingoo Han [Fri, 22 Feb 2013 00:43:51 +0000 (16:43 -0800)]
backlight: corgi_lcd: use lcd_get_data instead of dev_get_drvdata
Use the wrapper function for getting the driver data using lcd_device
instead of using dev_get_drvdata with &ld->dev, so we can directly pass a
struct lcd_device.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jingoo Han [Fri, 22 Feb 2013 00:43:50 +0000 (16:43 -0800)]
backlight: omap1: use bl_get_data instead of dev_get_drvdata
Use the wrapper function for getting the driver data using
backlight_device instead of using dev_get_drvdata with &bd->dev, so we can
directly pass a struct backlight_device.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jingoo Han [Fri, 22 Feb 2013 00:43:49 +0000 (16:43 -0800)]
backlight: tosa: use bl_get_data instead of dev_get_drvdata
Use the wrapper function for getting the driver data using
backlight_device instead of using dev_get_drvdata with &bd->dev, so we can
directly pass a struct backlight_device.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jingoo Han [Fri, 22 Feb 2013 00:43:48 +0000 (16:43 -0800)]
backlight: corgi_lcd: use bl_get_data instead of dev_get_drvdata
Use the wrapper function for getting the driver data using
backlight_device instead of using dev_get_drvdata with &bd->dev, so we can
directly pass a struct backlight_device.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jingoo Han [Fri, 22 Feb 2013 00:43:47 +0000 (16:43 -0800)]
backlight: ams369fg06: use bl_get_data instead of dev_get_drvdata
Use the wrapper function for getting the driver data using
backlight_device instead of using dev_get_drvdata with &bd->dev, so we can
directly pass a struct backlight_device.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jingoo Han [Fri, 22 Feb 2013 00:43:46 +0000 (16:43 -0800)]
pwm_backlight: use bl_get_data instead of dev_get_drvdata
Use the wrapper function for getting the driver data using
backlight_device instead of using dev_get_drvdata with &bd->dev, so we can
directly pass a struct backlight_device.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Cc: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jingoo Han [Fri, 22 Feb 2013 00:43:44 +0000 (16:43 -0800)]
backlight: aat2870: use bl_get_data instead of dev_get_drvdata
Use the wrapper function for getting the driver data using
backlight_device instead of using dev_get_drvdata with &bd->dev, so we can
directly pass a struct backlight_device.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jingoo Han [Fri, 22 Feb 2013 00:43:43 +0000 (16:43 -0800)]
backlight: lms501kf03: use spi_get_drvdata and spi_set_drvdata
Use the wrapper functions for getting and setting the driver data using
spi_device instead of using dev_{get|set}_drvdata with &spi->dev, so we
can directly pass a struct spi_device.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jingoo Han [Fri, 22 Feb 2013 00:43:42 +0000 (16:43 -0800)]
backlight: corgi_lcd: use spi_get_drvdata and spi_set_drvdata
Use the wrapper functions for getting and setting the driver data using
spi_device instead of using dev_{get|set}_drvdata with &spi->dev, so we
can directly pass a struct spi_device.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jingoo Han [Fri, 22 Feb 2013 00:43:41 +0000 (16:43 -0800)]
backlight: tosa: use spi_get_drvdata and spi_set_drvdata
Use the wrapper functions for getting and setting the driver data using
spi_device instead of using dev_{get|set}_drvdata with &spi->dev, so we
can directly pass a struct spi_device.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jingoo Han [Fri, 22 Feb 2013 00:43:40 +0000 (16:43 -0800)]
backlight: vgg2432a4: use spi_get_drvdata and spi_set_drvdata
Use the wrapper functions for getting and setting the driver data using
spi_device instead of using dev_{get|set}_drvdata with &spi->dev, so we
can directly pass a struct spi_device.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jingoo Han [Fri, 22 Feb 2013 00:43:39 +0000 (16:43 -0800)]
backlight: ams369fg06: use spi_get_drvdata and spi_set_drvdata
Use the wrapper functions for getting and setting the driver data using
spi_device instead of using dev_{get|set}_drvdata with &spi->dev, so we
can directly pass a struct spi_device.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jingoo Han [Fri, 22 Feb 2013 00:43:38 +0000 (16:43 -0800)]
backlight: lms283gf05: use spi_get_drvdata and spi_set_drvdata
Use the wrapper functions for getting and setting the driver data using
spi_device instead of using dev_{get|set}_drvdata with &spi->dev, so we
can directly pass a struct spi_device.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jingoo Han [Fri, 22 Feb 2013 00:43:37 +0000 (16:43 -0800)]
backlight: tdo24m: use spi_get_drvdata and spi_set_drvdata
Use the wrapper functions for getting and setting the driver data using
spi_device instead of using dev_{get|set}_drvdata with &spi->dev, so we
can directly pass a struct spi_device.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jingoo Han [Fri, 22 Feb 2013 00:43:36 +0000 (16:43 -0800)]
backlight: ltv350qv: use spi_get_drvdata and spi_set_drvdata
Use the wrapper functions for getting and setting the driver data using
spi_device instead of using dev_{get|set}_drvdata with &spi->dev, so we
can directly pass a struct spi_device.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jingoo Han [Fri, 22 Feb 2013 00:43:35 +0000 (16:43 -0800)]
backlight: s6e63m0: use spi_get_drvdata and spi_set_drvdata
Use the wrapper functions for getting and setting the driver data using
spi_device instead of using dev_{get|set}_drvdata with &spi->dev, so we
can directly pass a struct spi_device
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jingoo Han [Fri, 22 Feb 2013 00:43:33 +0000 (16:43 -0800)]
backlight: ld9040: use spi_get_drvdata and spi_set_drvdata
Use the wrapper functions for getting and setting the driver data using
spi_device instead of using dev_{get|set}_drvdata with &spi->dev, so we
can directly pass a struct spi_device.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jingoo Han [Fri, 22 Feb 2013 00:43:32 +0000 (16:43 -0800)]
backlight: l4f00242t03: use spi_get_drvdata and spi_set_drvdata
Use the wrapper functions for getting and setting the driver data using
spi_device instead of using dev_{get|set}_drvdata with &spi->dev, so we
can directly pass a struct spi_device.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jingoo Han [Fri, 22 Feb 2013 00:43:31 +0000 (16:43 -0800)]
backlight: ams369fg06: reorder inclusions of <linux/xxx.h>
Reorder inclusions of <linux/xxx.h> for redability, according to
alphabetical ordering. Also, unnecessary header comments are removed.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jingoo Han [Fri, 22 Feb 2013 00:43:30 +0000 (16:43 -0800)]
backlight: ams369fg06: remove redundant variable 'before_power'
'before_power' was used to check the previous status when resume() is
called. However, FB_BLANK_POWERDOWN was used in suspend() all the time,
so there is no need to check the previous status. Also, redundant return
variables are removed to reduce the code.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jingoo Han [Fri, 22 Feb 2013 00:43:29 +0000 (16:43 -0800)]
backlight: ams369fg06: replace EFAULT with EINVAL
Replace EFAULT with EINVAL, because EFAULT tends to be for the invalid
memory addresses.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jingoo Han [Fri, 22 Feb 2013 00:43:28 +0000 (16:43 -0800)]
backlight: ams369fg06: remove unnecessary NULL deference check
Remove unnecessary NULL deference check, because it was already checked in
ams369fg06_probe(). Also, unnecessary parentheses are removed in
ams369fg06_power_is_on().
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jingoo Han [Fri, 22 Feb 2013 00:43:27 +0000 (16:43 -0800)]
backlight: ams369fg06: use sleep instead of delay
Replace mdelay with msleep to remove the busy loop waiting.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jingoo Han [Fri, 22 Feb 2013 00:43:26 +0000 (16:43 -0800)]
backlight: s6e63m0: reorder inclusions of <linux/xxx.h>
Reorder inclusions of <linux/xxx.h> for redability, according to
alphabetical ordering. Also, unnecessary header comments are removed.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jingoo Han [Fri, 22 Feb 2013 00:43:25 +0000 (16:43 -0800)]
backlight: s6e63m0: remove redundant variable 'before_power'
'before_power' was used to check the previous status when resume() is
called. However, FB_BLANK_POWERDOWN was used in suspend() all the time,
so there is no need to check the previous status. Also, redundant return
variables are removed to reduce the code.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jingoo Han [Fri, 22 Feb 2013 00:43:24 +0000 (16:43 -0800)]
backlight: s6e63m0: replace EFAULT with EINVAL
Replace EFAULT with EINVAL, because EFAULT tends to be for the invalid
memory addresses.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jingoo Han [Fri, 22 Feb 2013 00:43:23 +0000 (16:43 -0800)]
backlight: s6e63m0: remove unnecessary NULL deference check
Remove unnecessary NULL deference check, because it was already checked in
s6e63m0_probe(). Also, POWER_IS_ON is replaced with
s6e63m0_power_is_on().
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jingoo Han [Fri, 22 Feb 2013 00:43:21 +0000 (16:43 -0800)]
backlight: s6e63m0: use sleep instead of delay
Replace mdelay with msleep to remove the busy loop waiting.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jingoo Han [Fri, 22 Feb 2013 00:43:20 +0000 (16:43 -0800)]
backlight: s6e63m0: use lowercase names of structs
Lowercase names of structs should be used, because they are
not preprocessor macros.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jingoo Han [Fri, 22 Feb 2013 00:43:19 +0000 (16:43 -0800)]
backlight: ld9040: reorder inclusions of <linux/xxx.h>
Reorder inclusions of <linux/xxx.h> for redability, according to
alphabetical ordering. Also, unnecessary header comments are removed.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jingoo Han [Fri, 22 Feb 2013 00:43:18 +0000 (16:43 -0800)]
backlight: ld9040: remove redundant return variables
Redundant return variables are removed to reduce the code.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jingoo Han [Fri, 22 Feb 2013 00:43:17 +0000 (16:43 -0800)]
backlight: ld9040: replace EFAULT with EINVAL
Replace EFAULT with EINVAL, because EFAULT tends to be for the invalid
memory addresses.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jingoo Han [Fri, 22 Feb 2013 00:43:16 +0000 (16:43 -0800)]
backlight: ld9040: remove unnecessary NULL deference check
Removee unnecessary NULL deference check, because it was already checked
in ld9040_probe(). Also, power_is_on is replaced with
ld9040_power_is_on().
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jingoo Han [Fri, 22 Feb 2013 00:43:15 +0000 (16:43 -0800)]
backlight: ld9040: use sleep instead of delay
Replace mdelay with msleep to remove the busy loop waiting.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jingoo Han [Fri, 22 Feb 2013 00:43:14 +0000 (16:43 -0800)]
backlight: add lms501kf03 LCD driver
Add the lms501kf03 LCD panel driver. The lms501kf03 LCD panel (800 x 480)
driver uses 3-wired SPI inteface.
[akpm@linux-foundation.org: remove unused variable `before_power']
[akpm@linux-foundation.org: make lms501kf03_shutdown() static, per Fengguang]
Signed-off-by: Ilho Lee <Ilho215.lee@samsung.com>
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Cc: "devendra.aaru" <devendra.aaru@gmail.com>
Cc: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Cody P Schafer [Fri, 22 Feb 2013 00:43:13 +0000 (16:43 -0800)]
MAINTAINERS: mm: add additional include files to listing
Add gfp.h, mmzone.h, memory_hotplug.h & vmalloc.h to the "MEMORY
MANAGMENT" section so scripts/get_maintainer.pl can do a better job of
making recommendations.
Signed-off-by: Cody P Schafer <cody@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Geert Uytterhoeven [Fri, 22 Feb 2013 00:43:12 +0000 (16:43 -0800)]
get_maintainer.pl: find maintainers for removed files
For removed files, get_maintainer.pl doesn't find any maintainers (besides
the default linux-kernel@vger.kernel.org), as it only looks at the "+++"
lines, which are "/dev/null" for removals. Fix this by extending the
parsing to the "---" lines.
E.g. for the two line test patch below the real score maintainers will now
be found:
--- a/arch/score/include/asm/dma-mapping.h
+++ /dev/null
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mikhail Gruzdev [Fri, 22 Feb 2013 00:43:10 +0000 (16:43 -0800)]
printk: add pr_devel_once and pr_devel_ratelimited
Standardize pr_devel logging macros family by adding pr_devel_once and
pr_devel_ratelimited.
Signed-off-by: Mikhail Gruzdev <michail.gruzdev@gmail.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
projects / kernel / kernel-generic.git / log