Javier González [Fri, 13 Oct 2017 12:46:06 +0000 (14:46 +0200)]
lightnvm: pblk: fix min size for page mempool
[ Upstream commit
bd432417681a224d9fa4a9d43be7d4edc82135b2 ]
pblk uses an internal page mempool for allocating pages on internal
bios. The main two users of this memory pool are partial reads (reads
with some sectors in cache and some on media) and padded writes, which
need to add dummy pages to an existing bio already containing valid
data (and with a large enough bioset allocated). In both cases, the
maximum number of pages per bio is defined by the maximum number of
physical sectors supported by the underlying device.
This patch fixes a bad mempool allocation, where the min_nr of elements
on the pool was fixed (to 16), which is lower than the maximum number
of sectors supported by NVMe (as of the time for this patch). Instead,
use the maximum number of allowed sectors reported by the device.
Reported-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Javier González [Fri, 13 Oct 2017 12:46:01 +0000 (14:46 +0200)]
lightnvm: pblk: initialize debug stat counter
[ Upstream commit
a1121176ff757e3c073490a69608ea0b18a00ec1 ]
Initialize the stat counter for garbage collected reads.
Fixes:
a4bd217b43268 ("lightnvm: physical block device (pblk) target")
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Javier González [Fri, 13 Oct 2017 12:46:02 +0000 (14:46 +0200)]
lightnvm: pblk: use right flag for GC allocation
[ Upstream commit
7d327a9ed6c4dca341ebf99012e0a6b80a3050e6 ]
The data buffer for the GC path allocates virtual memory through
vmalloc. When this change was introduced, a flag signaling kmalloc'ed
memory was wrongly introduced. Use the right flag when creating a bio
from this buffer.
Fixes:
de54e703a422 ("lightnvm: pblk: use vmalloc for GC data buffer")
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rakesh Pandit [Fri, 13 Oct 2017 12:46:28 +0000 (14:46 +0200)]
lightnvm: pblk: fix changing GC group list for a line
[ Upstream commit
27b978725d895e704aab44b99242a0514485d798 ]
pblk_line_gc_list seems to had a bug since the introduction of pblk in
getting GC list for a line. In
b20ba1bc7 while redesigning the GC
algorithm, the naming for the GC thresholds was altered, but the
values for high_thrs and mid_thrs were not. The result is that when
moving to the GC lists, the mid threshold is never evaluated.
Fixes:
a4bd217b4("lightnvm: physical block device (pblk) target")
Signed-off-by: Rakesh Pandit <rakesh@tuxera.com>
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hans Holmberg [Fri, 13 Oct 2017 12:46:34 +0000 (14:46 +0200)]
lightnvm: pblk: prevent gc kicks when gc is not operational
[ Upstream commit
3e3a5b8ebd5d3b1d68facc58b0674a2564653222 ]
GC can be kicked after it has been shut down when closing the last
line during exit, resulting in accesses to freed structures.
Make sure that GC is not triggered while it is not operational.
Also make sure that GC won't be re-activated during exit when
running on another processor by using timer_del_sync.
Signed-off-by: Hans Holmberg <hans.holmberg@cnexlabs.com>
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Matteo Croce [Thu, 12 Oct 2017 14:12:37 +0000 (16:12 +0200)]
icmp: don't fail on fragment reassembly time exceeded
[ Upstream commit
258bbb1b0e594ad5f5652cb526b3c63e6a7fad3d ]
The ICMP implementation currently replies to an ICMP time exceeded message
(type 11) with an ICMP host unreachable message (type 3, code 1).
However, time exceeded messages can either represent "time to live exceeded
in transit" (code 0) or "fragment reassembly time exceeded" (code 1).
Unconditionally replying to "fragment reassembly time exceeded" with
host unreachable messages might cause unjustified connection resets
which are now easily triggered as UFO has been removed, because, in turn,
sending large buffers triggers IP fragmentation.
The issue can be easily reproduced by running a lot of UDP streams
which is likely to trigger IP fragmentation:
# start netserver in the test namespace
ip netns add test
ip netns exec test netserver
# create a VETH pair
ip link add name veth0 type veth peer name veth0 netns test
ip link set veth0 up
ip -n test link set veth0 up
for i in $(seq 20 29); do
# assign addresses to both ends
ip addr add dev veth0 192.168.$i.1/24
ip -n test addr add dev veth0 192.168.$i.2/24
# start the traffic
netperf -L 192.168.$i.1 -H 192.168.$i.2 -t UDP_STREAM -l 0 &
done
# wait
send_data: data send error: No route to host (errno 113)
netperf: send_omni: send_data failed: No route to host
We need to differentiate instead: if fragment reassembly time exceeded
is reported, we need to silently drop the packet,
if time to live exceeded is reported, maintain the current behaviour.
In both cases increment the related error count "icmpInTimeExcds".
While at it, fix a typo in a comment, and convert the if statement
into a switch to mate it more readable.
Signed-off-by: Matteo Croce <mcroce@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alex Vesker [Tue, 10 Oct 2017 07:36:41 +0000 (10:36 +0300)]
IB/ipoib: Grab rtnl lock on heavy flush when calling ndo_open/stop
[ Upstream commit
b4b678b06f6eef18bff44a338c01870234db0bc9 ]
When ndo_open and ndo_stop are called RTNL lock should be held.
In this specific case ipoib_ib_dev_open calls the offloaded ndo_open
which re-sets the number of TX queue assuming RTNL lock is held.
Since RTNL lock is not held, RTNL assert will fail.
Signed-off-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Bart Van Assche [Wed, 11 Oct 2017 17:48:45 +0000 (10:48 -0700)]
RDMA/cma: Avoid triggering undefined behavior
[ Upstream commit
c0b64f58e8d49570aa9ee55d880f92c20ff0166b ]
According to the C standard the behavior of computations with
integer operands is as follows:
* A computation involving unsigned operands can never overflow,
because a result that cannot be represented by the resulting
unsigned integer type is reduced modulo the number that is one
greater than the largest value that can be represented by the
resulting type.
* The behavior for signed integer underflow and overflow is
undefined.
Hence only use unsigned integers when checking for integer
overflow.
This patch is what I came up with after having analyzed the
following smatch warnings:
drivers/infiniband/core/cma.c:3448: cma_resolve_ib_udp() warn: signed overflow undefined. 'offset + conn_param->private_data_len < conn_param->private_data_len'
drivers/infiniband/core/cma.c:3505: cma_connect_ib() warn: signed overflow undefined. 'offset + conn_param->private_data_len < conn_param->private_data_len'
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Acked-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Bart Van Assche [Wed, 11 Oct 2017 17:48:43 +0000 (10:48 -0700)]
IB/core: Fix endianness annotation in rdma_is_multicast_addr()
[ Upstream commit
1c3aea2bc8f0b2e5b57375ead40457ff75a3a2ec ]
Since ipv4_addr is a big endian 32-bit number, annotate it as such.
Fixes: commit
be1d325a3358 ("IB/core: Set RoCEv2 MGID according to spec")
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alexander Duyck [Fri, 13 Oct 2017 20:40:24 +0000 (13:40 -0700)]
macvlan: Only deliver one copy of the frame to the macvlan interface
[ Upstream commit
dd6b9c2c332b40f142740d1b11fb77c653ff98ea ]
This patch intoduces a slight adjustment for macvlan to address the fact
that in source mode I was seeing two copies of any packet addressed to the
macvlan interface being delivered where there should have been only one.
The issue appears to be that one copy was delivered based on the source MAC
address and then the second copy was being delivered based on the
destination MAC address. To fix it I am just treating a unicast address
match as though it is not a match since source based macvlan isn't supposed
to be matching based on the destination MAC anyway.
Fixes:
79cf79abce71 ("macvlan: add source mode")
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jan Kara [Mon, 16 Oct 2017 09:38:11 +0000 (11:38 +0200)]
udf: Avoid overflow when session starts at large offset
[ Upstream commit
abdc0eb06964fe1d2fea6dd1391b734d0590365d ]
When session starts beyond offset 2^31 the arithmetics in
udf_check_vsd() would overflow. Make sure the computation is done in
large enough type.
Reported-by: Cezary Sliwa <sliwa@ifpan.edu.pl>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Chuck Lever [Mon, 9 Oct 2017 16:03:26 +0000 (12:03 -0400)]
xprtrdma: Don't defer fencing an async RPC's chunks
[ Upstream commit
8f66b1a529047a972cb9602a919c53a95f3d7a2b ]
In current kernels, waiting in xprt_release appears to be safe to
do. I had erroneously believed that for ASYNC RPCs, waiting of any
kind in xprt_release->xprt_rdma_free would result in deadlock. I've
done injection testing and consulted with Trond to confirm that
waiting in the RPC release path is safe.
For the very few times where RPC resources haven't yet been released
earlier by the reply handler, it is safe to wait synchronously in
xprt_rdma_free for invalidation rather than defering it to MR
recovery.
Note: When the QP is error state, posting a LocalInvalidate should
flush and mark the MR as bad. There is no way the remote HCA can
access that MR via a QP in error state, so it is effectively already
inaccessible and thus safe for the Upper Layer to access. The next
time the MR is used it should be recognized and cleaned up properly
by frwr_op_map.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Guoqing Jiang [Fri, 29 Sep 2017 01:16:43 +0000 (09:16 +0800)]
md-cluster: fix wrong condition check in raid1_write_request
[ Upstream commit
385f4d7f946b08f36f68b0a28e95a319925b6b62 ]
The check used here is to avoid conflict between write and
resync, however we used the wrong logic, it should be the
inverse of the checking inside "if".
Fixes: 589a1c4 ("Suspend writes in RAID1 if within range")
Signed-off-by: Guoqing Jiang <gqjiang@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Artur Paszkiewicz [Fri, 29 Sep 2017 20:54:19 +0000 (22:54 +0200)]
raid5-ppl: check recovery_offset when performing ppl recovery
[ Upstream commit
07719ff767dcd8cc42050f185d332052f3816546 ]
If starting an array that is undergoing rebuild, make ppl recovery honor
the recovery_offset of a member disk and don't read data that is not yet
in-sync.
Signed-off-by: Artur Paszkiewicz <artur.paszkiewicz@intel.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dan Carpenter [Wed, 4 Oct 2017 07:50:37 +0000 (10:50 +0300)]
scsi: bfa: integer overflow in debugfs
[ Upstream commit
3e351275655d3c84dc28abf170def9786db5176d ]
We could allocate less memory than intended because we do:
bfad->regdata = kzalloc(len << 2, GFP_KERNEL);
The shift can overflow leading to a crash. This is debugfs code so the
impact is very small. I fixed the network version of this in March with
commit
13e2d5187f6b ("bna: integer overflow bug in debugfs").
Fixes:
ab2a9ba189e8 ("[SCSI] bfa: add debugfs support")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
weiping zhang [Thu, 12 Oct 2017 06:56:44 +0000 (14:56 +0800)]
scsi: sd: change allow_restart to bool in sysfs interface
[ Upstream commit
658e9a6dc1126f21fa417cd213e1cdbff8be0ba2 ]
/sys/class/scsi_disk/0:2:0:0/allow_restart can be changed to 0
unexpectedly by writing an invalid string such as the following:
echo asdf > /sys/class/scsi_disk/0:2:0:0/allow_restart
Signed-off-by: weiping zhang <zhangweiping@didichuxing.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
weiping zhang [Thu, 12 Oct 2017 06:57:06 +0000 (14:57 +0800)]
scsi: sd: change manage_start_stop to bool in sysfs interface
[ Upstream commit
623401ee33e42cee64d333877892be8db02951eb ]
/sys/class/scsi_disk/0:2:0:0/manage_start_stop can be changed to 0
unexpectly by writing an invalid string.
Signed-off-by: weiping zhang <zhangweiping@didichuxing.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Wei Yongjun [Tue, 17 Oct 2017 12:11:46 +0000 (12:11 +0000)]
nullb: fix error return code in null_init()
[ Upstream commit
30c516d750396c5f3ec9cb04c9e025c25e91495e ]
Fix to return error code -ENOMEM from the null_alloc_dev() error
handling case instead of 0, as done elsewhere in this function.
Fixes:
2984c8684f96 ("nullb: factor disk parameters")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Colin Ian King [Tue, 17 Oct 2017 15:54:52 +0000 (16:54 +0100)]
ipmi_si: fix memory leak on new_smi
[ Upstream commit
c0a32fe13cd323ca9420500b16fd69589c9ba91e ]
The error exit path omits kfree'ing the allocated new_smi, causing a memory
leak. Fix this by kfree'ing new_smi.
Detected by CoverityScan, CID#
14582571 ("Resource Leak")
Fixes:
7e030d6dff71 ("ipmi: Prefer ACPI system interfaces over SMBIOS ones")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jia-Ju Bai [Sun, 8 Oct 2017 11:54:07 +0000 (19:54 +0800)]
rtl8188eu: Fix a possible sleep-in-atomic bug in rtw_disassoc_cmd
[ Upstream commit
08880f8e08cbd814e870e9d3ab9530abc1bce226 ]
The driver may sleep under a spinlock, and the function call path is:
rtw_set_802_11_bssid(acquire the spinlock)
rtw_disassoc_cmd
kzalloc(GFP_KERNEL) --> may sleep
To fix it, GFP_KERNEL is replaced with GFP_ATOMIC.
This bug is found by my static analysis tool and my code review.
Signed-off-by: Jia-Ju Bai <baijiaju1990@163.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jia-Ju Bai [Sun, 8 Oct 2017 11:54:45 +0000 (19:54 +0800)]
rtl8188eu: Fix a possible sleep-in-atomic bug in rtw_createbss_cmd
[ Upstream commit
2bf9806d4228f7a6195f8e03eda0479d2a93b411 ]
The driver may sleep under a spinlock, and the function call path is:
rtw_surveydone_event_callback(acquire the spinlock)
rtw_createbss_cmd
kzalloc(GFP_KERNEL) --> may sleep
To fix it, GFP_KERNEL is replaced with GFP_ATOMIC.
This bug is found by my static analysis tool and my code review.
Signed-off-by: Jia-Ju Bai <baijiaju1990@163.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Don Hiatt [Mon, 9 Oct 2017 19:38:12 +0000 (12:38 -0700)]
IB/hfi1: Mask out A bit from psn trace
[ Upstream commit
d0a2f454713a42447ee4007582c0e43c47bcf230 ]
The trace logic prior to the fixes below used to mask the
A bit from the psn. It now mistakenly displays the A bit,
which is already displayed separately.
Fix by adding the appropriate mask to the psn tracing.
Fixes:
228d2af1b723 ("IB/hfi1: Separate input/output header tracing")
Fixes:
863cf89d472f ("IB/hfi1: Add 16B trace support")
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Don Hiatt <don.hiatt@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jia-Ju Bai [Mon, 9 Oct 2017 08:45:55 +0000 (16:45 +0800)]
vt6655: Fix a possible sleep-in-atomic bug in vt6655_suspend
[ Upstream commit
42c8eb3f6e15367981b274cb79ee4657e2c6949d ]
The driver may sleep under a spinlock, and the function call path is:
vt6655_suspend (acquire the spinlock)
pci_set_power_state
__pci_start_power_transition (drivers/pci/pci.c)
msleep --> may sleep
To fix it, pci_set_power_state is called without having a spinlock.
This bug is found by my static analysis tool and my code review.
Signed-off-by: Jia-Ju Bai <baijiaju1990@163.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Parav Pandit [Mon, 16 Oct 2017 05:45:16 +0000 (08:45 +0300)]
IB/core: Fix calculation of maximum RoCE MTU
[ Upstream commit
99260132fde7bddc6e0132ce53da94d1c9ccabcb ]
The original code only took into consideration the largest header
possible after the IB_BTH_BYTES. This was incorrect, as the largest
possible header size is the largest possible combination of headers we
might run into. The new code accounts for all possible headers in the
largest possible combination and subtracts that from the MTU to make
sure that all packets will fit on the wire.
Link: https://www.spinics.net/lists/linux-rdma/msg54558.html
Fixes:
3c86aa70bf67 ("RDMA/cm: Add RDMA CM support for IBoE devices")
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Reported-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Parav Pandit [Mon, 16 Oct 2017 05:45:15 +0000 (08:45 +0300)]
IB/core: Fix use workqueue without WQ_MEM_RECLAIM
[ Upstream commit
39baf10310e6669564a485b55267fae70a4e44ae ]
The IB/core provides address resolution service and invokes callback
handler when address resolve request completes of requester in worker
thread context.
Such caller might allocate or free memory in callback handler
depending on the completion status to make further progress or to
terminate a connection. Most ULPs resolve route which involves
allocating route entry and path record elements in callback event handler.
It has been noticed that WQ_MEM_RECLAIM flag should not be used for
workers that tend to allocate memory in this [1] thread discussion.
In order to mitigate this situation, WQ_MEM_RECLAIM flag was dropped for
other such WQs in this [2] patch.
Similar problem might arise with address resolution path, though its not
yet noticed. The ib_addr workqueue is not memory reclaim path due to its
nature of invoking callback that might allocate memory or don't free any
memory under memory pressure.
[1] https://www.spinics.net/lists/linux-rdma/msg53239.html
[2] https://www.spinics.net/lists/linux-rdma/msg53416.html
Fixes:
f54816261c2b ("IB/addr: Remove deprecated create_singlethread_workqueue")
Fixes:
5fff41e1f89d ("IB/core: Fix race condition in resolving IP to MAC")
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Kurt Garloff [Tue, 17 Oct 2017 07:10:45 +0000 (09:10 +0200)]
scsi: scsi_devinfo: Add REPORTLUN2 to EMC SYMMETRIX blacklist entry
[ Upstream commit
909cf3e16a5274fe2127cf3cea5c8dba77b2c412 ]
All EMC SYMMETRIX support REPORT_LUNS, even if configured to report
SCSI-2 for whatever reason.
Signed-off-by: Kurt Garloff <garloff@suse.de>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
NeilBrown [Tue, 17 Oct 2017 05:18:36 +0000 (16:18 +1100)]
raid5: Set R5_Expanded on parity devices as well as data.
[ Upstream commit
235b6003fb28f0dd8e7ed8fbdb088bb548291766 ]
When reshaping a fully degraded raid5/raid6 to a larger
nubmer of devices, the new device(s) are not in-sync
and so that can make the newly grown stripe appear to be
"failed".
To avoid this, we set the R5_Expanded flag to say "Even though
this device is not fully in-sync, this block is safe so
don't treat the device as failed for this stripe".
This flag is set for data devices, not not for parity devices.
Consequently, if you have a RAID6 with two devices that are partly
recovered and a spare, and start a reshape to include the spare,
then when the reshape gets past the point where the recovery was
up to, it will think the stripes are failed and will get into
an infinite loop, failing to make progress.
So when contructing parity on an EXPAND_READY stripe,
set R5_Expanded.
Reported-by: Curt <lightspd@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Linus Walleij [Wed, 11 Oct 2017 09:57:15 +0000 (11:57 +0200)]
pinctrl: adi2: Fix Kconfig build problem
[ Upstream commit
1c363531dd814dc4fe10865722bf6b0f72ce4673 ]
The build robot is complaining on Blackfin:
drivers/pinctrl/pinctrl-adi2.c: In function 'port_setup':
>> drivers/pinctrl/pinctrl-adi2.c:221:21: error: dereferencing
pointer to incomplete type 'struct gpio_port_t'
writew(readw(®s->port_fer) & ~BIT(offset),
^~
drivers/pinctrl/pinctrl-adi2.c: In function 'adi_gpio_ack_irq':
>> drivers/pinctrl/pinctrl-adi2.c:266:18: error: dereferencing
pointer to incomplete type 'struct bfin_pint_regs'
if (readl(®s->invert_set) & pintbit)
^~
It seems the driver need to include <asm/gpio.h> and <asm/irq.h>
to compile.
The Blackfin architecture was re-defining the Kconfig
PINCTRL symbol which is not OK, so replaced this with
PINCTRL_BLACKFIN_ADI2 which selects PINCTRL and PINCTRL_ADI2
just like most arches do.
Further, the old GPIO driver symbol GPIO_ADI was possible to
select at the same time as selecting PINCTRL. This was not
working because the arch-local <asm/gpio.h> header contains
an explicit #ifndef PINCTRL clause making compilation break
if you combine them. The same is true for DEBUG_MMRS.
Make sure the ADI2 pinctrl driver is not selected at the same
time as the old GPIO implementation. (This should be converted
to use gpiolib or pincontrol and move to drivers/...) Also make
sure the old GPIO_ADI driver or DEBUG_MMRS is not selected at
the same time as the new PINCTRL implementation, and only make
PINCTRL_ADI2 selectable for the Blackfin families that actually
have it.
This way it is still possible to add e.g. I2C-based pin
control expanders on the Blackfin.
Cc: Steven Miao <realmz6@gmail.com>
Cc: Huanhuan Feng <huanhuan.feng@analog.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ross Zwisler [Wed, 18 Oct 2017 18:21:55 +0000 (12:21 -0600)]
dev/dax: fix uninitialized variable build warning
[ Upstream commit
0a3ff78699d1817e711441715d22665475466036 ]
Fix this build warning:
warning: 'phys' may be used uninitialized in this function
[-Wuninitialized]
As reported here:
https://lkml.org/lkml/2017/10/16/152
http://kisskb.ellerman.id.au/kisskb/buildresult/
13181373/log/
Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
nixiaoming [Fri, 15 Sep 2017 09:45:56 +0000 (17:45 +0800)]
tty fix oops when rmmod 8250
[ Upstream commit
c79dde629d2027ca80329c62854a7635e623d527 ]
After rmmod 8250.ko
tty_kref_put starts kwork (release_one_tty) to release proc interface
oops when accessing driver->driver_name in proc_tty_unregister_driver
Use jprobe, found driver->driver_name point to 8250.ko
static static struct uart_driver serial8250_reg
.driver_name= serial,
Use name in proc_dir_entry instead of driver->driver_name to fix oops
test on linux 4.1.12:
BUG: unable to handle kernel paging request at
ffffffffa01979de
IP: [<
ffffffff81310f40>] strchr+0x0/0x30
PGD 1a0d067 PUD 1a0e063 PMD
851c1f067 PTE 0
Oops: 0000 [#1] PREEMPT SMP
Modules linked in: ... ... [last unloaded: 8250]
CPU: 7 PID: 116 Comm: kworker/7:1 Tainted: G O 4.1.12 #1
Hardware name: Insyde RiverForest/Type2 - Board Product Name1, BIOS NE5KV904 12/21/2015
Workqueue: events release_one_tty
task:
ffff88085b684960 ti:
ffff880852884000 task.ti:
ffff880852884000
RIP: 0010:[<
ffffffff81310f40>] [<
ffffffff81310f40>] strchr+0x0/0x30
RSP: 0018:
ffff880852887c90 EFLAGS:
00010282
RAX:
ffffffff81a5eca0 RBX:
ffffffffa01979de RCX:
0000000000000004
RDX:
ffff880852887d10 RSI:
000000000000002f RDI:
ffffffffa01979de
RBP:
ffff880852887cd8 R08:
0000000000000000 R09:
ffff88085f5d94d0
R10:
0000000000000195 R11:
0000000000000000 R12:
ffffffffa01979de
R13:
ffff880852887d00 R14:
ffffffffa01979de R15:
ffff88085f02e840
FS:
0000000000000000(0000) GS:
ffff88085f5c0000(0000) knlGS:
0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0:
0000000080050033
CR2:
ffffffffa01979de CR3:
0000000001a0c000 CR4:
00000000001406e0
Stack:
ffffffff812349b1 ffff880852887cb8 ffff880852887d10 ffff88085f5cd6c2
ffff880852800a80 ffffffffa01979de ffff880852800a84 0000000000000010
ffff88085bb28bd8 ffff880852887d38 ffffffff812354f0 ffff880852887d08
Call Trace:
[<
ffffffff812349b1>] ? __xlate_proc_name+0x71/0xd0
[<
ffffffff812354f0>] remove_proc_entry+0x40/0x180
[<
ffffffff815f6811>] ? _raw_spin_lock_irqsave+0x41/0x60
[<
ffffffff813be520>] ? destruct_tty_driver+0x60/0xe0
[<
ffffffff81237c68>] proc_tty_unregister_driver+0x28/0x40
[<
ffffffff813be548>] destruct_tty_driver+0x88/0xe0
[<
ffffffff813be5bd>] tty_driver_kref_put+0x1d/0x20
[<
ffffffff813becca>] release_one_tty+0x5a/0xd0
[<
ffffffff81074159>] process_one_work+0x139/0x420
[<
ffffffff810745a1>] worker_thread+0x121/0x450
[<
ffffffff81074480>] ? process_scheduled_works+0x40/0x40
[<
ffffffff8107a16c>] kthread+0xec/0x110
[<
ffffffff81080000>] ? tg_rt_schedulable+0x210/0x220
[<
ffffffff8107a080>] ? kthread_freezable_should_stop+0x80/0x80
[<
ffffffff815f7292>] ret_from_fork+0x42/0x70
[<
ffffffff8107a080>] ? kthread_freezable_should_stop+0x80/0x80
Signed-off-by: nixiaoming <nixiaoming@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Wanpeng Li [Wed, 18 Oct 2017 23:00:34 +0000 (07:00 +0800)]
KVM: nVMX: Fix EPT switching advertising
[ Upstream commit
575b3a2cb439b03fd603ea77c73c76f3ed237596 ]
I can use vmxcap tool to observe "EPTP Switching yes" even if EPT is not
exposed to L1.
EPT switching is advertised unconditionally since it is emulated, however,
it can be treated as an extended feature for EPT and it should not be
advertised if EPT itself is not exposed. This patch fixes it.
Reviewed-by: David Hildenbrand <david@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Jim Mattson <jmattson@google.com>
Signed-off-by: Wanpeng Li <wanpeng.li@hotmail.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Eric Dumazet [Thu, 19 Oct 2017 00:02:03 +0000 (17:02 -0700)]
ipv4: ipv4_default_advmss() should use route mtu
[ Upstream commit
164a5e7ad531e181334a3d3f03d0d5ad20d6faea ]
ipv4_default_advmss() incorrectly uses the device MTU instead
of the route provided one. IPv6 has the proper behavior,
lets harmonize the two protocols.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Matthias Brugger [Sat, 21 Oct 2017 08:17:47 +0000 (10:17 +0200)]
soc: mediatek: pwrap: fix compiler errors
[ Upstream commit
fb2c1934f30577756e55e24e8870b45c78da3bc2 ]
When compiling using sparse, we got the following error:
drivers/soc/mediatek/mtk-pmic-wrap.c:686:25: error: dubious one-bit signed bitfield
Changing the data type to unsigned fixes this.
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Breno Leitao [Tue, 17 Oct 2017 18:20:18 +0000 (16:20 -0200)]
powerpc/xmon: Check before calling xive functions
[ Upstream commit
402e172a2ce76210f2fe921cf419d12103851344 ]
Currently xmon could call XIVE functions from OPAL even if the XIVE is
disabled or does not exist in the system, as in POWER8 machines. This
causes the following exception:
1:mon> dx
cpu 0x1: Vector: 700 (Program Check) at [
c000000423c93450]
pc:
c00000000009cfa4: opal_xive_dump+0x50/0x68
lr:
c0000000000997b8: opal_return+0x0/0x50
This patch simply checks if XIVE is enabled before calling XIVE
functions.
Fixes:
243e25112d06 ("powerpc/xive: Native exploitation of the XIVE interrupt controller")
Suggested-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Signed-off-by: Breno Leitao <leitao@debian.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Michael Ellerman [Mon, 9 Oct 2017 10:52:44 +0000 (21:52 +1100)]
powerpc/perf/hv-24x7: Fix incorrect comparison in memord
[ Upstream commit
05c14c03138532a3cb2aa29c2960445c8753343b ]
In the hv-24x7 code there is a function memord() which tries to
implement a sort function return -1, 0, 1. However one of the
conditions is incorrect, such that it can never be true, because we
will have already returned.
I don't believe there is a bug in practice though, because the
comparisons are an optimisation prior to calling memcmp().
Fix it by swapping the second comparision, so it can be true.
Reported-by: David Binderman <dcb314@hotmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan Hovold [Mon, 16 Oct 2017 13:06:19 +0000 (15:06 +0200)]
serdev: ttyport: enforce tty-driver open() requirement
[ Upstream commit
dee7d0f3b200c67c6ee96bd37c6e8fa52690ab56 ]
The tty-driver open routine is mandatory, but the serdev
tty-port-controller implementation did not treat it as such and would
instead fall back to calling tty_port_open() directly.
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Lipeng [Mon, 23 Oct 2017 11:51:01 +0000 (19:51 +0800)]
net: hns3: fix a bug when alloc new buffer
[ Upstream commit
b9077428ec5569aacb2952d8a2ffb51c8988d3c2 ]
When alloce new buffer to HW, should unmap the old buffer first.
This old code map the old buffer but not unmap the old buffer,
this patch fixes it.
Fixes: 76ad4f0 (net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC)
Signed-off-by: Lipeng <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Lipeng [Mon, 23 Oct 2017 11:51:02 +0000 (19:51 +0800)]
net: hns3: fix the bug when map buffer fail
[ Upstream commit
564883bb4dc1a4f3cba6344e77743175694b0761 ]
If one buffer had been recieved to stack, driver will alloc a new buffer,
map the buffer to device and replace the old buffer. When map fail, should
only free the new alloced buffer, but not free all buffers in the ring.
Fixes: 76ad4f0 (net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC)
Signed-off-by: Lipeng <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Lipeng [Mon, 23 Oct 2017 11:51:05 +0000 (19:51 +0800)]
net: hns3: fix the TX/RX ring.queue_index in hns3_ring_get_cfg
[ Upstream commit
66b447301ac710ee237dba8b653244018fbb6168 ]
The interface hns3_ring_get_cfg only update TX ring queue_index,
but do not update RX ring queue_index. This patch fixes it.
Fixes: 76ad4f0 (net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC)
Signed-off-by: Lipeng <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alexey Khoroshilov [Fri, 13 Oct 2017 22:06:56 +0000 (01:06 +0300)]
mfd: mxs-lradc: Fix error handling in mxs_lradc_probe()
[ Upstream commit
362741a21a5c4b9ee31e75ce28d63c6d238a745c ]
There is the only path, where mxs_lradc_probe() leaves clk undisabled,
since it does return instead of goto err_clk.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Martin Wilck [Fri, 20 Oct 2017 21:51:08 +0000 (16:51 -0500)]
scsi: hpsa: destroy sas transport properties before scsi_host
[ Upstream commit
dfb2e6f46b3074eb85203d8f0888b71ec1c2e37a ]
This patch cleans up a lot of warnings when unloading the driver.
A current example of the stack trace starts with:
[ 142.570715] sysfs group 'power' not found for kobject 'port-5:0'
There can be hundreds of these messages during a driver unload.
I am resubmitting this patch on behalf of Martin Wilck with his
permission.
His original patch can be found here:
https://www.spinics.net/lists/linux-scsi/msg102085.html
This patch did not help until Hannes's
commit
9441284fbc39 ("scsi-fixup-kernel-warning-during-rmmod")
was applied to the kernel.
---------------------------
Original patch description:
---------------------------
Unloading the hpsa driver causes warnings
[ 1063.793652] WARNING: CPU: 1 PID: 4850 at ../fs/sysfs/group.c:237 device_del+0x54/0x240()
[ 1063.793659] sysfs group
ffffffff81cf21a0 not found for kobject 'port-2:0'
with two different stacks:
1)
[ 1063.793774] [<
ffffffff81448af4>] device_del+0x54/0x240
[ 1063.793780] [<
ffffffff8145178a>] transport_remove_classdev+0x4a/0x60
[ 1063.793784] [<
ffffffff81451216>] attribute_container_device_trigger+0xa6/0xb0
[ 1063.793802] [<
ffffffffa0105d46>] sas_port_delete+0x126/0x160 [scsi_transport_sas]
[ 1063.793819] [<
ffffffffa036ebcc>] hpsa_free_sas_port+0x3c/0x70 [hpsa]
2)
[ 1063.797103] [<
ffffffff81448af4>] device_del+0x54/0x240
[ 1063.797118] [<
ffffffffa0105d4e>] sas_port_delete+0x12e/0x160 [scsi_transport_sas]
[ 1063.797134] [<
ffffffffa036ebcc>] hpsa_free_sas_port+0x3c/0x70 [hpsa]
This is caused by the fact that host device hostX is deleted before the
SAS transport devices hostX/port-a:b.
This patch fixes this by reverting the order of device deletions.
Tested-by: Don Brace <don.brace@microsemi.com>
Reviewed-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin Wilck <mwilck@suse.de>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Martin Wilck [Fri, 20 Oct 2017 21:51:14 +0000 (16:51 -0500)]
scsi: hpsa: cleanup sas_phy structures in sysfs when unloading
[ Upstream commit
55ca38b4255bb336c2d35990bdb2b368e19b435a ]
I am resubmitting this patch on behalf of Martin Wilck with his
permission.
The original patch can be found here:
https://www.spinics.net/lists/linux-scsi/msg102083.html
This patch did not help until Hannes's
commit
9441284fbc39 ("scsi-fixup-kernel-warning-during-rmmod")
was applied to the kernel.
--------------------------------------
Original patch description from Martin:
--------------------------------------
When the hpsa module is unloaded using rmmod, dangling
symlinks remain under /sys/class/sas_phy. Fix this by
calling sas_phy_delete() rather than sas_phy_free (which,
according to comments, should not be called for PHYs that
have been set up successfully, anyway).
Tested-by: Don Brace <don.brace@microsemi.com>
Reviewed-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin Wilck <mwilck@suse.de>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Xiaofei Tan [Tue, 24 Oct 2017 15:51:38 +0000 (23:51 +0800)]
scsi: hisi_sas: fix the risk of freeing slot twice
[ Upstream commit
6ba0fbc35aa9f3bc8c12be3b4047055c9ce2ac92 ]
The function hisi_sas_slot_task_free() is used to free the slot and do
tidy-up of LLDD resources. The LLDD generally should know the state of
a slot and decide when to free it, and it should only be done once.
For some scenarios, we really don't know the state, like when TMF
timeout. In this case, we check task->lldd_task before calling
hisi_sas_slot_task_free().
However, we may miss some scenarios when we should also check
task->lldd_task, and it is not SMP safe to check task->lldd_task as we
don't protect it within spin lock.
This patch is to fix this risk of freeing slot twice, as follows:
1. Check task->lldd_task in the hisi_sas_slot_task_free(), and give
up freeing of this time if task->lldd_task is NULL.
2. Set slot->buf to NULL after it is freed.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alex Williamson [Wed, 11 Oct 2017 21:35:56 +0000 (15:35 -0600)]
PCI: Detach driver before procfs & sysfs teardown on device remove
[ Upstream commit
16b6c8bb687cc3bec914de09061fcb8411951fda ]
When removing a device, for example a VF being removed due to SR-IOV
teardown, a "soft" hot-unplug via 'echo 1 > remove' in sysfs, or an actual
hot-unplug, we first remove the procfs and sysfs attributes for the device
before attempting to release the device from any driver bound to it.
Unbinding the driver from the device can take time. The device might need
to write out data or it might be actively in use. If it's in use by
userspace through a vfio driver, the unbind might block until the user
releases the device. This leads to a potentially non-trivial amount of
time where the device exists, but we've torn down the interfaces that
userspace uses to examine devices, for instance lspci might generate this
sort of error:
pcilib: Cannot open /sys/bus/pci/devices/0000:01:0a.3/config
lspci: Unable to read the standard configuration space header of device 0000:01:0a.3
We don't seem to have any dependence on this teardown ordering in the
kernel, so let's unbind the driver first, which is also more symmetric with
the instantiation of the device in pci_bus_add_device().
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Leon Romanovsky [Wed, 25 Oct 2017 04:41:11 +0000 (07:41 +0300)]
RDMA/cxgb4: Declare stag as __be32
[ Upstream commit
35fb2a88ed4b77356fa679a8525c869a3594e287 ]
The scqe.stag is actually __b32, fix it.
drivers/infiniband/hw/cxgb4/cq.c:754:52: warning: cast to restricted __be32
Cc: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Reviewed-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Lipeng [Tue, 24 Oct 2017 13:02:09 +0000 (21:02 +0800)]
net: hns3: fix the bug of hns3_set_txbd_baseinfo
[ Upstream commit
7036d26f328f12a323069eb16d965055b4cb3795 ]
The SC bits of TX BD mean switch control. For this area, value 0
indicates no switch control, the packet is routed according to the
forwarding table. Value 1 indicates that the packet is transmitted
to the network bypassing the forwarding table.
As HNS3 driver need support VF later, VF conmunicate with its own
PF need forwarding table. This patch sets SC bits of TX BD 0 and use
forwarding table.
Fixes: 76ad4f0 (net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC)
Signed-off-by: Lipeng <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Lipeng [Tue, 24 Oct 2017 13:02:10 +0000 (21:02 +0800)]
net: hns3: add nic_client check when initialize roce base information
[ Upstream commit
3a46f34d20d453f09defb76b11a567647939c0aa ]
Roce driver works base on HNS3 driver.If insmod Roce driver before
NIC driver there is a error because do not check nic_client. This patch
adds nic_client check when initialize roce base information.
Fixes: 46a3df9 (net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support)
Signed-off-by: Lipeng <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Lipeng [Tue, 24 Oct 2017 13:02:11 +0000 (21:02 +0800)]
net: hns3: fix a bug in hclge_uninit_client_instance
[ Upstream commit
a17dcf3f0124698d1120da71574bf4c339e5a368 ]
HNS3 driver initialize hdev->roce_client and vport->roce.client in
hclge_init_client_instance, and need set hdev->roce_client and
vport->roce.client NULL.
If do not set them NULL when uninit, it will fail in the scene:
insmod hns3.ko, hns-roce.ko, hns-roce-hw-v3.ko successfully, but
rmmod hns3.ko after rmmod hns-roce-hw-v2.ko and hns-roce.ko.
This patch fixes the issue.
Fixes: 46a3df9 (net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support)
Signed-off-by: Lipeng <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Egil Hjelmeland [Tue, 24 Oct 2017 15:14:10 +0000 (17:14 +0200)]
net: dsa: lan9303: Do not disable switch fabric port 0 at .probe
[ Upstream commit
3c91b0c1de8d013490bbc41ce9ee8810ea5baddd ]
Make the LAN9303 work when lan9303_probe() is called twice.
For some unknown reason the LAN9303 switch fail to forward data when switch
fabric port 0 TX is disabled during probe. (Write of LAN9303_MAC_TX_CFG_0
in lan9303_disable_processing_port().)
In that situation the switch fabric seem to receive frames, because the ALR
is learning addresses. But no frames are transmitted on any of the ports.
In our system lan9303_probe() is called twice, first time
dsa_register_switch() return -EPROBE_DEFER. As an experiment, modified the
code to skip writing LAN9303_MAC_TX_CFG_0, port 0 during the first probe.
Then the switch works as expected.
Resolve the problem by not calling lan9303_disable_processing_port() on
port 0 during probe. Ports 1 and 2 are still disabled.
Although unsatisfying that the exact failure mechanism is not known,
the patch should not cause any harm.
Signed-off-by: Egil Hjelmeland <privat@egil-hjelmeland.no>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Christoph Hellwig [Tue, 17 Oct 2017 21:16:19 +0000 (14:16 -0700)]
xfs: fix incorrect extent state in xfs_bmap_add_extent_unwritten_real
[ Upstream commit
5e422f5e4fd71d18bc6b851eeb3864477b3d842e ]
There was one spot in xfs_bmap_add_extent_unwritten_real that didn't use the
passed in new extent state but always converted to normal, leading to wrong
behavior when converting from normal to unwritten.
Only found by code inspection, it seems like this code path to move partial
extent from written to unwritten while merging it with the next extent is
rarely exercised.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Darrick J. Wong [Wed, 18 Oct 2017 04:37:32 +0000 (21:37 -0700)]
xfs: return a distinct error code value for IGET_INCORE cache misses
[ Upstream commit
ed438b476b611c67089760037139f93ea8ed41d5 ]
For an XFS_IGET_INCORE iget operation, if the inode isn't in the cache,
return ENODATA so that we don't confuse it with the pre-existing ENOENT
cases (inode is in cache, but freed).
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Brian Foster [Thu, 26 Oct 2017 16:31:16 +0000 (09:31 -0700)]
xfs: fix log block underflow during recovery cycle verification
[ Upstream commit
9f2a4505800607e537e9dd9dea4f55c4b0c30c7a ]
It is possible for mkfs to format very small filesystems with too
small of an internal log with respect to the various minimum size
and block count requirements. If this occurs when the log happens to
be smaller than the scan window used for cycle verification and the
scan wraps the end of the log, the start_blk calculation in
xlog_find_head() underflows and leads to an attempt to scan an
invalid range of log blocks. This results in log recovery failure
and a failed mount.
Since there may be filesystems out in the wild with this kind of
geometry, we cannot simply refuse to mount. Instead, cap the scan
window for cycle verification to the size of the physical log. This
ensures that the cycle verification proceeds as expected when the
scan wraps the end of the log.
Reported-by: Zorro Lang <zlang@redhat.com>
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jiri Slaby [Wed, 25 Oct 2017 13:57:55 +0000 (15:57 +0200)]
l2tp: cleanup l2tp_tunnel_delete calls
[ Upstream commit
4dc12ffeaeac939097a3f55c881d3dc3523dff0c ]
l2tp_tunnel_delete does not return anything since commit
62b982eeb458
("l2tp: fix race condition in l2tp_tunnel_delete"). But call sites of
l2tp_tunnel_delete still do casts to void to avoid unused return value
warnings.
Kill these now useless casts.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Sabrina Dubroca <sd@queasysnail.net>
Cc: Guillaume Nault <g.nault@alphalink.fr>
Cc: David S. Miller <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Acked-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Christoph Hellwig [Wed, 18 Oct 2017 11:20:01 +0000 (13:20 +0200)]
nvme: use kref_get_unless_zero in nvme_find_get_ns
[ Upstream commit
2dd4122854f697afc777582d18548dded03ce5dd ]
For kref_get_unless_zero to protect against lookup vs free races we need
to use it in all places where we aren't guaranteed to already hold a
reference. There is no such guarantee in nvme_find_get_ns, so switch to
kref_get_unless_zero in this function.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Osama Khan [Sat, 21 Oct 2017 10:42:21 +0000 (10:42 +0000)]
platform/x86: hp_accel: Add quirk for HP ProBook 440 G4
[ Upstream commit
163ca80013aafb6dc9cb295de3db7aeab9ab43f8 ]
Added support for HP ProBook 440 G4 laptops by including the accelerometer
orientation quirk for that device. Testing was performed based on the
axis orientation guidelines here:
https://www.kernel.org/doc/Documentation/misc-devices/lis3lv02d
which states "If the left side is elevated, X increases (becomes positive)".
When tested, on lifting the left edge, x values became increasingly negative
thus indicating an inverted x-axis on the installed lis3lv02d chip.
This was compensated by adding an entry for this device in hp_accel.c
specifying the quirk as x_inverted. The patch was tested on a
ProBook 440 G4 device and x-axis as well as y and z-axis values are now
generated as per spec.
Signed-off-by: Osama Khan <osama.khan@ericsson.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Felix Manlunas [Thu, 26 Oct 2017 23:46:36 +0000 (16:46 -0700)]
liquidio: fix kernel panic in VF driver
[ Upstream commit
aa28667cfbe4ff6f14454dda210b1f2e485f99b5 ]
Doing ifconfig down on VF driver in the middle of receiving line rate
traffic causes a kernel panic:
LiquidIO_VF 0000:02:00.3: should not come here should not get rx when poll mode = 0 for vf
BUG: unable to handle kernel NULL pointer dereference at (null)
.
.
.
Call Trace:
<IRQ>
? tasklet_action+0x102/0x120
__do_softirq+0x91/0x292
irq_exit+0xb6/0xc0
do_IRQ+0x4f/0xd0
common_interrupt+0x93/0x93
</IRQ>
RIP: 0010:cpuidle_enter_state+0x142/0x2f0
RSP: 0018:
ffffffffa6403e20 EFLAGS:
00000246 ORIG_RAX:
ffffffffffffff59
RAX:
0000000000000000 RBX:
0000000000000003 RCX:
000000000000001f
RDX:
0000000000000000 RSI:
000000002ab7519f RDI:
0000000000000000
RBP:
ffffffffa6403e58 R08:
0000000000000084 R09:
0000000000000018
R10:
ffffffffa6403df0 R11:
00000000000003c7 R12:
0000000000000003
R13:
ffffd27ebd806800 R14:
ffffffffa64d40d8 R15:
0000007be072823f
cpuidle_enter+0x17/0x20
call_cpuidle+0x23/0x40
do_idle+0x18c/0x1f0
cpu_startup_entry+0x64/0x70
rest_init+0xa5/0xb0
start_kernel+0x45e/0x46b
x86_64_start_reservations+0x24/0x26
x86_64_start_kernel+0x6f/0x72
secondary_startup_64+0xa5/0xa5
Code: Bad RIP value.
RIP: (null) RSP:
ffff9246ed003f28
CR2:
0000000000000000
---[ end trace
92731e80f31b7d7d ]---
Kernel panic - not syncing: Fatal exception in interrupt
Kernel Offset: 0x24000000 from 0xffffffff81000000 (relocation range: 0xffffffff80000000-0xffffffffbfffffff)
---[ end Kernel panic - not syncing: Fatal exception in interrupt
Reason is: in the function assigned to net_device_ops->ndo_stop, the steps
for bringing down the interface are done in the wrong order. The step that
notifies the NIC firmware to stop forwarding packets to host is done too
late. Fix it by moving that step to the beginning.
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tushar Dave [Fri, 27 Oct 2017 23:12:30 +0000 (16:12 -0700)]
samples/bpf: adjust rlimit RLIMIT_MEMLOCK for xdp1
[ Upstream commit
6dfca831c03ef654b1f7bff1b8d487d330e9f76b ]
Default rlimit RLIMIT_MEMLOCK is 64KB, causes bpf map failure.
e.g.
[root@lab bpf]#./xdp1 -N $(</sys/class/net/eth2/ifindex)
failed to create a map: 1 Operation not permitted
Fix it.
Signed-off-by: Tushar Dave <tushar.n.dave@oracle.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Bartosz Chronowski [Thu, 26 Oct 2017 08:22:43 +0000 (10:22 +0200)]
Bluetooth: btusb: Add new NFA344A entry.
[ Upstream commit
858ff38af77fc660092e82474ecc6ac135ed29fe ]
This change allows proper low power mode entry in suspend.
/sys/kernel/debug/usb/devices entry:
T: Bus=01 Lev=01 Prnt=01 Port=05 Cnt=03 Dev#= 3 Spd=12 MxCh= 0
D: Ver= 2.01 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0489 ProdID=e09f Rev= 0.01
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
Signed-off-by: Bartosz Chronowski <ext.bartosz.chronowski@tieto.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Neil Armstrong [Thu, 19 Oct 2017 10:31:09 +0000 (12:31 +0200)]
ARM64: dts: meson-gxbb-odroidc2: fix usb1 power supply
[ Upstream commit
e841ec956e539f4002f5e9fe9f9e904dcca12d5d ]
Looking at the schematics, the USB Power Supply is shared between the
two USB interfaces,
If the usb0 fails to initialize, the second one won't have power.
Fixes:
5a0803bd5ae2 ("ARM64: dts: meson-gxbb-odroidc2: Enable USB Nodes")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Geert Uytterhoeven [Thu, 26 Oct 2017 15:12:33 +0000 (17:12 +0200)]
mtd: spi-nor: stm32-quadspi: Fix uninitialized error return code
[ Upstream commit
05521bd3d117704a1458eb4d0c3ae821858658f2 ]
With gcc 4.1.2:
drivers/mtd/spi-nor/stm32-quadspi.c: In function ‘stm32_qspi_tx_poll’:
drivers/mtd/spi-nor/stm32-quadspi.c:230: warning: ‘ret’ may be used uninitialized in this function
Indeed, if stm32_qspi_cmd.len is zero, ret will be uninitialized.
This length is passed from outside the driver using the
spi_nor.{read,write}{,_reg}() callbacks.
Several functions in drivers/mtd/spi-nor/spi-nor.c (e.g. write_enable(),
write_disable(), and erase_chip()) call spi_nor.write_reg() with a zero
length.
Fix this by returning an explicit zero on success.
Fixes:
0d43d7ab277a048c ("mtd: spi-nor: add driver for STM32 quad spi flash controller")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sergey Matyukevich [Mon, 30 Oct 2017 10:13:46 +0000 (13:13 +0300)]
qtnfmac: modify full Tx queue error reporting
[ Upstream commit
e9931f984dd1e80adb3b5e095ef175fe383bc92d ]
Under heavy load it is normal that h/w Tx queue is almost full all the time
and reclaim should be done before transmitting next packet. Warning still
should be reported as well as s/w Tx queues should be stopped in the
case when reclaim failed.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Christophe JAILLET [Sun, 10 Sep 2017 11:19:38 +0000 (13:19 +0200)]
btrfs: tests: Fix a memory leak in error handling path in 'run_test()'
[ Upstream commit
9ca2e97fa3c3216200afe35a3b111ec51cc796d2 ]
If 'btrfs_alloc_path()' fails, we must free the resources already
allocated, as done in the other error handling paths in this function.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Qu Wenruo <quwenruo.btrfs@gmx.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Colin Ian King [Mon, 11 Sep 2017 15:15:28 +0000 (16:15 +0100)]
btrfs: avoid null pointer dereference on fs_info when calling btrfs_crit
[ Upstream commit
3993b112dac968612b0b213ed59cb30f50b0015b ]
There are checks on fs_info in __btrfs_panic to avoid dereferencing a
null fs_info, however, there is a call to btrfs_crit that may also
dereference a null fs_info. Fix this by adding a check to see if fs_info
is null and only print the s_id if fs_info is non-null.
Detected by CoverityScan CID#401973 ("Dereference after null check")
Fixes:
efe120a067c8 ("Btrfs: convert printk to btrfs_ and fix BTRFS prefix")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Anand Jain [Thu, 28 Sep 2017 06:51:09 +0000 (14:51 +0800)]
btrfs: undo writable superblocke when sprouting fails
[ Upstream commit
0af2c4bf5a012a40a2f9230458087d7f068339d0 ]
When new device is being added to seed FS, seed FS is marked writable,
but when we fail to bring in the new device, we missed to undo the
writable part. This patch fixes it.
Signed-off-by: Anand Jain <anand.jain@oracle.com>
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Nikolay Borisov [Thu, 28 Sep 2017 07:53:17 +0000 (10:53 +0300)]
btrfs: Explicitly handle btrfs_update_root failure
[ Upstream commit
9417ebc8a676487c6ec8825f92fb28f7dbeb5f4b ]
btrfs_udpate_root can fail and it aborts the transaction, the correct
way to handle an aborted transaction is to explicitly end with
btrfs_end_transaction. Even now the code is correct since
btrfs_commit_transaction would handle an aborted transaction but this is
more of an implementation detail. So let's be explicit in handling
failure in btrfs_update_root.
Furthermore btrfs_commit_transaction can also fail and by ignoring it's
return value we could have left the in-memory copy of the root item in
an inconsistent state. So capture the error value which allows us to
correctly revert the RO/RW flags in case of commit failure.
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Anand Jain [Sat, 14 Oct 2017 00:34:02 +0000 (08:34 +0800)]
btrfs: fix false EIO for missing device
[ Upstream commit
102ed2c5ff932439bbbe74c7bd63e6d5baa9f732 ]
When one of the device is missing, bbio_error() takes care of setting
the error status. And if its only IO that is pending in that stripe, it
fails to check the status of the other IO at %bbio_error before setting
the error %bi_status for the %orig_bio. Fix this by checking if
%bbio->error has exceeded the %bbio->max_errors.
Reproducer as below fdatasync error is seen intermittently.
mount -o degraded /dev/sdc /btrfs
dd status=none if=/dev/zero of=$(mktemp /btrfs/XXX) bs=4096 count=1 conv=fdatasync
dd: fdatasync failed for ‘/btrfs/LSe’: Input/output error
The reason for the intermittences of the problem is because
the following conditions have to be met, which depends on timing:
In btrfs_map_bio()
- the RAID1 the missing device has to be at %dev_nr = 1
In bbio_error()
. before bbio_error() is called the bio of the not-missing
device at %dev_nr = 0 must be completed so that the below
condition is true
if (atomic_dec_and_test(&bbio->stripes_pending)) {
Signed-off-by: Anand Jain <anand.jain@oracle.com>
Reviewed-by: Liu Bo <bo.li.liu@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Nick Desaulniers [Fri, 27 Oct 2017 16:33:41 +0000 (09:33 -0700)]
arm64: prevent regressions in compressed kernel image size when upgrading to binutils 2.27
[ Upstream commit
fd9dde6abcb9bfe6c6bee48834e157999f113971 ]
Upon upgrading to binutils 2.27, we found that our lz4 and gzip
compressed kernel images were significantly larger, resulting is 10ms
boot time regressions.
As noted by Rahul:
"aarch64 binaries uses RELA relocations, where each relocation entry
includes an addend value. This is similar to x86_64. On x86_64, the
addend values are also stored at the relocation offset for relative
relocations. This is an optimization: in the case where code does not
need to be relocated, the loader can simply skip processing relative
relocations. In binutils-2.25, both bfd and gold linkers did this for
x86_64, but only the gold linker did this for aarch64. The kernel build
here is using the bfd linker, which stored zeroes at the relocation
offsets for relative relocations. Since a set of zeroes compresses
better than a set of non-zero addend values, this behavior was resulting
in much better lz4 compression.
The bfd linker in binutils-2.27 is now storing the actual addend values
at the relocation offsets. The behavior is now consistent with what it
does for x86_64 and what gold linker does for both architectures. The
change happened in this upstream commit:
https://sourceware.org/git/?p=binutils-gdb.git;a=commit;h=
1f56df9d0d5ad89806c24e71f296576d82344613
Since a bunch of zeroes got replaced by non-zero addend values, we see
the side effect of lz4 compressed image being a bit bigger.
To get the old behavior from the bfd linker, "--no-apply-dynamic-relocs"
flag can be used:
$ LDFLAGS="--no-apply-dynamic-relocs" make
With this flag, the compressed image size is back to what it was with
binutils-2.25.
If the kernel is using ASLR, there aren't additional runtime costs to
--no-apply-dynamic-relocs, as the relocations will need to be applied
again anyway after the kernel is relocated to a random address.
If the kernel is not using ASLR, then presumably the current default
behavior of the linker is better. Since the static linker performed the
dynamic relocs, and the kernel is not moved to a different address at
load time, it can skip applying the relocations all over again."
Some measurements:
$ ld -v
GNU ld (binutils-2.25-
f3d35cf6) 2.25.51.
20141117
^
$ ls -l vmlinux
-rwxr-x--- 1 ndesaulniers eng
300652760 Oct 26 11:57 vmlinux
$ ls -l Image.lz4-dtb
-rw-r----- 1 ndesaulniers eng
16932627 Oct 26 11:57 Image.lz4-dtb
$ ld -v
GNU ld (binutils-2.27-
53dd00a1) 2.27.0.
20170315
^
pre patch:
$ ls -l vmlinux
-rwxr-x--- 1 ndesaulniers eng
300376208 Oct 26 11:43 vmlinux
$ ls -l Image.lz4-dtb
-rw-r----- 1 ndesaulniers eng
18159474 Oct 26 11:43 Image.lz4-dtb
post patch:
$ ls -l vmlinux
-rwxr-x--- 1 ndesaulniers eng
300376208 Oct 26 12:06 vmlinux
$ ls -l Image.lz4-dtb
-rw-r----- 1 ndesaulniers eng
16932466 Oct 26 12:06 Image.lz4-dtb
By Siqi's measurement w/ gzip:
binutils 2.27 with this patch (with --no-apply-dynamic-relocs):
Image
41535488
Image.gz
13404067
binutils 2.27 without this patch (without --no-apply-dynamic-relocs):
Image
41535488
Image.gz
14125516
Any compression scheme should be able to get better results from the
longer runs of zeros, not just GZIP and LZ4.
10ms boot time savings isn't anything to get excited about, but users of
arm64+compression+bfd-2.27 should not have to pay a penalty for no
runtime improvement.
Reported-by: Gopinath Elanchezhian <gelanchezhian@google.com>
Reported-by: Sindhuri Pentyala <spentyala@google.com>
Reported-by: Wei Wang <wvw@google.com>
Suggested-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Suggested-by: Rahul Chaudhry <rahulchaudhry@google.com>
Suggested-by: Siqi Lin <siqilin@google.com>
Suggested-by: Stephen Hines <srhines@google.com>
Signed-off-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
[will: added comment to Makefile]
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ronald Tschalär [Thu, 26 Oct 2017 05:15:19 +0000 (22:15 -0700)]
Bluetooth: hci_ldisc: Fix another race when closing the tty.
[ Upstream commit
0338b1b393ec7910898e8f7b25b3bf31a7282e16 ]
The following race condition still existed:
P1 P2
cancel_work_sync()
hci_uart_tx_wakeup()
hci_uart_write_work()
hci_uart_dequeue()
clear_bit(HCI_UART_PROTO_READY)
hci_unregister_dev(hdev)
hci_free_dev(hdev)
hu->proto->close(hu)
kfree(hu)
access to hdev and hu
Cancelling the work after clearing the HCI_UART_PROTO_READY bit avoids
this as any hci_uart_tx_wakeup() issued after the flag is cleared will
detect that and not schedule further work.
Signed-off-by: Ronald Tschalär <ronald@innovation.ch>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Patel Jay P [Mon, 23 Oct 2017 13:05:53 +0000 (06:05 -0700)]
Ib/hfi1: Return actual operational VLs in port info query
[ Upstream commit
00f9203119dd2774564407c7a67b17d81916298b ]
__subn_get_opa_portinfo stores value returned by hfi1_get_ib_cfg() as
operational vls. hfi1_get_ib_cfg() returns vls_operational field in
hfi1_pportdata. The problem with this is that the value is always equal
to vls_supported field in hfi1_pportdata.
The logic to calculate operational_vls is to set value passed by FM
(in __subn_set_opa_portinfo routine). If no value is passed then
default value is stored in operational_vls.
Field actual_vls_operational is calculated on the basis of buffer
control table. Hence, modifying hfi1_get_ib_cfg() to return
actual_operational_vls when used with HFI1_IB_CFG_OP_VLS parameter
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Patel Jay P <jay.p.patel@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tang.junhui [Mon, 30 Oct 2017 21:46:34 +0000 (14:46 -0700)]
bcache: fix wrong cache_misses statistics
[ Upstream commit
c157313791a999646901b3e3c6888514ebc36d62 ]
Currently, Cache missed IOs are identified by s->cache_miss, but actually,
there are many situations that missed IOs are not assigned a value for
s->cache_miss in cached_dev_cache_miss(), for example, a bypassed IO
(s->iop.bypass = 1), or the cache_bio allocate failed. In these situations,
it will go to out_put or out_submit, and s->cache_miss is null, which leads
bch_mark_cache_accounting() to treat this IO as a hit IO.
[ML: applied by 3-way merge]
Signed-off-by: tang.junhui <tang.junhui@zte.com.cn>
Reviewed-by: Michael Lyle <mlyle@lyle.org>
Reviewed-by: Coly Li <colyli@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Liang Chen [Mon, 30 Oct 2017 21:46:35 +0000 (14:46 -0700)]
bcache: explicitly destroy mutex while exiting
[ Upstream commit
330a4db89d39a6b43f36da16824eaa7a7509d34d ]
mutex_destroy does nothing most of time, but it's better to call
it to make the code future proof and it also has some meaning
for like mutex debug.
As Coly pointed out in a previous review, bcache_exit() may not be
able to handle all the references properly if userspace registers
cache and backing devices right before bch_debug_init runs and
bch_debug_init failes later. So not exposing userspace interface
until everything is ready to avoid that issue.
Signed-off-by: Liang Chen <liangchen.linux@gmail.com>
Reviewed-by: Michael Lyle <mlyle@lyle.org>
Reviewed-by: Coly Li <colyli@suse.de>
Reviewed-by: Eric Wheeler <bcache@linux.ewheeler.net>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Arun Kumar Neelakantam [Mon, 30 Oct 2017 05:41:24 +0000 (11:11 +0530)]
rpmsg: glink: Initialize the "intent_req_comp" completion variable
[ Upstream commit
2394facb17bcace4b3c19b50202177a5d8903b64 ]
The "intent_req_comp" variable is used without initialization which
results in NULL pointer dereference in qcom_glink_request_intent().
we need to initialize the completion variable before using it.
Fixes:
27b9c5b66b23 ("rpmsg: glink: Request for intents when unavailable")
Signed-off-by: Arun Kumar Neelakantam <aneela@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adam Sampson [Tue, 24 Oct 2017 20:14:46 +0000 (16:14 -0400)]
media: usbtv: fix brightness and contrast controls
[ Upstream commit
b3168c87c0492661badc3e908f977d79e7738a41 ]
Because the brightness and contrast controls share a register,
usbtv_s_ctrl needs to read the existing values for both controls before
inserting the new value. However, the code accidentally wrote to the
registers (from an uninitialised stack array), rather than reading them.
The user-visible effect of this was that adjusting the brightness would
also set the contrast to a random value, and vice versa -- so it wasn't
possible to correctly adjust the brightness of usbtv's video output.
Tested with an "EasyDAY" UTV007 device.
Fixes:
c53a846c48f2 ("usbtv: add video controls")
Signed-off-by: Adam Sampson <ats@offog.org>
Reviewed-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Bob Peterson [Wed, 20 Sep 2017 13:30:04 +0000 (08:30 -0500)]
GFS2: Take inode off order_write list when setting jdata flag
[ Upstream commit
cc555b09d8c3817aeebda43a14ab67049a5653f7 ]
This patch fixes a deadlock caused when the jdata flag is set for
inodes that are already on the ordered write list. Since it is
on the ordered write list, log_flush calls gfs2_ordered_write which
calls filemap_fdatawrite. But since the inode had the jdata flag
set, that calls gfs2_jdata_writepages, which tries to start a new
transaction. A new transaction cannot be started because it tries
to acquire the log_flush rwsem which is already locked by the log
flush operation.
The bottom line is: We cannot switch an inode from ordered to jdata
until we eliminate any ordered data pages (via log flush) or any
log_flush operation afterward will create the circular dependency
above. So we need to flush the log before setting the diskflags to
switch the file mode, then we need to remove the inode from the
ordered writes list.
Before this patch, the log flush was done for jdata->ordered, but
that's wrong. If we're going from jdata to ordered, we don't need
to call gfs2_log_flush because the call to filemap_fdatawrite will
do it for us:
filemap_fdatawrite() -> __filemap_fdatawrite_range()
__filemap_fdatawrite_range() -> do_writepages()
do_writepages() -> gfs2_jdata_writepages()
gfs2_jdata_writepages() -> gfs2_log_flush()
This patch modifies function do_gfs2_set_flags so that if a file
has its jdata flag set, and it's already on the ordered write list,
the log will be flushed and it will be removed from the list
before setting the flag.
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Acked-by: Abhijith Das <adas@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Douglas Gilbert [Sun, 29 Oct 2017 14:47:19 +0000 (10:47 -0400)]
scsi: scsi_debug: write_same: fix error report
[ Upstream commit
e33d7c56450b0a5c7290cbf9e1581fab5174f552 ]
The scsi_debug driver incorrectly suggests there is an error with the
SCSI WRITE SAME command when the number_of_logical_blocks is greater
than 1. It will also suggest there is an error when NDOB
(no data-out buffer) is set and the number_of_logical_blocks is
greater than 0. Both are valid, fix.
Signed-off-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dan Carpenter [Sat, 30 Sep 2017 08:16:51 +0000 (11:16 +0300)]
misc: pci_endpoint_test: Avoid triggering a BUG()
[ Upstream commit
846df244ebefbc9f7b91e9ae7a5e5a2e69fb4772 ]
If you call ida_simple_remove(&pci_endpoint_test_ida, id) with a
negative "id" then it triggers an immediate BUG_ON(). Let's not allow
that.
Fixes:
2c156ac71c6b ("misc: Add host side PCI driver for PCI test function device")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Kishon Vijay Abraham I [Wed, 11 Oct 2017 08:44:36 +0000 (14:14 +0530)]
misc: pci_endpoint_test: Fix failure path return values in probe
[ Upstream commit
80068c93688f6143100859c4856f895801c1a1d9 ]
Return value of pci_endpoint_test_probe is not set properly in a couple of
failure cases. Fix it here.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Daniel Lezcano [Thu, 19 Oct 2017 17:05:58 +0000 (19:05 +0200)]
thermal/drivers/step_wise: Fix temperature regulation misbehavior
[ Upstream commit
07209fcf33542c1ff1e29df2dbdf8f29cdaacb10 ]
There is a particular situation when the cooling device is cpufreq and the heat
dissipation is not efficient enough where the temperature increases little by
little until reaching the critical threshold and leading to a SoC reset.
The behavior is reproducible on a hikey6220 with bad heat dissipation (eg.
stacked with other boards).
Running a simple C program doing while(1); for each CPU of the SoC makes the
temperature to reach the passive regulation trip point and ends up to the
maximum allowed temperature followed by a reset.
This issue has been also reported by running the libhugetlbfs test suite.
What is observed is a ping pong between two cpu frequencies, 1.2GHz and 900MHz
while the temperature continues to grow.
It appears the step wise governor calls get_target_state() the first time with
the throttle set to true and the trend to 'raising'. The code selects logically
the next state, so the cpu frequency decreases from 1.2GHz to 900MHz, so far so
good. The temperature decreases immediately but still stays greater than the
trip point, then get_target_state() is called again, this time with the
throttle set to true *and* the trend to 'dropping'. From there the algorithm
assumes we have to step down the state and the cpu frequency jumps back to
1.2GHz. But the temperature is still higher than the trip point, so
get_target_state() is called with throttle=1 and trend='raising' again, we jump
to 900MHz, then get_target_state() is called with throttle=1 and
trend='dropping', we jump to 1.2GHz, etc ... but the temperature does not
stabilizes and continues to increase.
[ 237.922654] thermal thermal_zone0: Trip0[type=1,temp=65000]:trend=1,throttle=1
[ 237.922678] thermal thermal_zone0: Trip1[type=1,temp=75000]:trend=1,throttle=1
[ 237.922690] thermal cooling_device0: cur_state=0
[ 237.922701] thermal cooling_device0: old_target=0, target=1
[ 238.026656] thermal thermal_zone0: Trip0[type=1,temp=65000]:trend=2,throttle=1
[ 238.026680] thermal thermal_zone0: Trip1[type=1,temp=75000]:trend=2,throttle=1
[ 238.026694] thermal cooling_device0: cur_state=1
[ 238.026707] thermal cooling_device0: old_target=1, target=0
[ 238.134647] thermal thermal_zone0: Trip0[type=1,temp=65000]:trend=1,throttle=1
[ 238.134667] thermal thermal_zone0: Trip1[type=1,temp=75000]:trend=1,throttle=1
[ 238.134679] thermal cooling_device0: cur_state=0
[ 238.134690] thermal cooling_device0: old_target=0, target=1
In this situation the temperature continues to increase while the trend is
oscillating between 'dropping' and 'raising'. We need to keep the current state
untouched if the throttle is set, so the temperature can decrease or a higher
state could be selected, thus preventing this oscillation.
Keeping the next_target untouched when 'throttle' is true at 'dropping' time
fixes the issue.
The following traces show the governor does not change the next state if
trend==2 (dropping) and throttle==1.
[ 2306.127987] thermal thermal_zone0: Trip0[type=1,temp=65000]:trend=1,throttle=1
[ 2306.128009] thermal thermal_zone0: Trip1[type=1,temp=75000]:trend=1,throttle=1
[ 2306.128021] thermal cooling_device0: cur_state=0
[ 2306.128031] thermal cooling_device0: old_target=0, target=1
[ 2306.231991] thermal thermal_zone0: Trip0[type=1,temp=65000]:trend=2,throttle=1
[ 2306.232016] thermal thermal_zone0: Trip1[type=1,temp=75000]:trend=2,throttle=1
[ 2306.232030] thermal cooling_device0: cur_state=1
[ 2306.232042] thermal cooling_device0: old_target=1, target=1
[ 2306.335982] thermal thermal_zone0: Trip0[type=1,temp=65000]:trend=0,throttle=1
[ 2306.336006] thermal thermal_zone0: Trip1[type=1,temp=75000]:trend=0,throttle=1
[ 2306.336021] thermal cooling_device0: cur_state=1
[ 2306.336034] thermal cooling_device0: old_target=1, target=1
[ 2306.439984] thermal thermal_zone0: Trip0[type=1,temp=65000]:trend=2,throttle=1
[ 2306.440008] thermal thermal_zone0: Trip1[type=1,temp=75000]:trend=2,throttle=0
[ 2306.440022] thermal cooling_device0: cur_state=1
[ 2306.440034] thermal cooling_device0: old_target=1, target=0
[ ... ]
After a while, if the temperature continues to increase, the next state becomes
2 which is 720MHz on the hikey. That results in the temperature stabilizing
around the trip point.
[ 2455.831982] thermal thermal_zone0: Trip0[type=1,temp=65000]:trend=1,throttle=1
[ 2455.832006] thermal thermal_zone0: Trip1[type=1,temp=75000]:trend=1,throttle=0
[ 2455.832019] thermal cooling_device0: cur_state=1
[ 2455.832032] thermal cooling_device0: old_target=1, target=1
[ 2455.935985] thermal thermal_zone0: Trip0[type=1,temp=65000]:trend=0,throttle=1
[ 2455.936013] thermal thermal_zone0: Trip1[type=1,temp=75000]:trend=0,throttle=0
[ 2455.936027] thermal cooling_device0: cur_state=1
[ 2455.936040] thermal cooling_device0: old_target=1, target=1
[ 2456.043984] thermal thermal_zone0: Trip0[type=1,temp=65000]:trend=0,throttle=1
[ 2456.044009] thermal thermal_zone0: Trip1[type=1,temp=75000]:trend=0,throttle=0
[ 2456.044023] thermal cooling_device0: cur_state=1
[ 2456.044036] thermal cooling_device0: old_target=1, target=1
[ 2456.148001] thermal thermal_zone0: Trip0[type=1,temp=65000]:trend=1,throttle=1
[ 2456.148028] thermal thermal_zone0: Trip1[type=1,temp=75000]:trend=1,throttle=1
[ 2456.148042] thermal cooling_device0: cur_state=1
[ 2456.148055] thermal cooling_device0: old_target=1, target=2
[ 2456.252009] thermal thermal_zone0: Trip0[type=1,temp=65000]:trend=2,throttle=1
[ 2456.252041] thermal thermal_zone0: Trip1[type=1,temp=75000]:trend=2,throttle=0
[ 2456.252058] thermal cooling_device0: cur_state=2
[ 2456.252075] thermal cooling_device0: old_target=2, target=1
IOW, this change is needed to keep the state for a cooling device if the
temperature trend is oscillating while the temperature increases slightly.
Without this change, the situation above leads to a catastrophic crash by a
hardware reset on hikey. This issue has been reported to happen on an OMAP
dra7xx also.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Keerthy <j-keerthy@ti.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Leo Yan <leo.yan@linaro.org>
Tested-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Kuninori Morimoto [Wed, 1 Nov 2017 07:16:58 +0000 (07:16 +0000)]
ASoC: rsnd: rsnd_ssi_run_mods() needs to care ssi_parent_mod
[ Upstream commit
21781e87881f9c420871b1d1f3f29d4cd7bffb10 ]
SSI parent mod might be NULL. ssi_parent_mod() needs to care
about it. Otherwise, it uses negative shift.
This patch fixes it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Gao Feng [Tue, 31 Oct 2017 10:25:37 +0000 (18:25 +0800)]
ppp: Destroy the mutex when cleanup
[ Upstream commit
f02b2320b27c16b644691267ee3b5c110846f49e ]
The mutex_destroy only makes sense when enable DEBUG_MUTEX. For the
good readbility, it's better to invoke it in exit func when the init
func invokes mutex_init.
Signed-off-by: Gao Feng <gfree.wind@vip.163.com>
Acked-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Michał Mirosław [Tue, 19 Sep 2017 02:48:10 +0000 (04:48 +0200)]
clk: tegra: Fix cclk_lp divisor register
[ Upstream commit
54eff2264d3e9fd7e3987de1d7eba1d3581c631e ]
According to comments in code and common sense, cclk_lp uses its
own divisor, not cclk_g's.
Fixes:
b08e8c0ecc42 ("clk: tegra: add clock support for Tegra30")
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Acked-By: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Nicolin Chen [Fri, 15 Sep 2017 19:10:13 +0000 (12:10 -0700)]
clk: tegra: Use readl_relaxed_poll_timeout_atomic() in tegra210_clock_init()
[ Upstream commit
22ef01a203d27fee8b7694020b7e722db7efd2a7 ]
Below is the call trace of tegra210_init_pllu() function:
start_kernel()
-> time_init()
--> of_clk_init()
---> tegra210_clock_init()
----> tegra210_pll_init()
-----> tegra210_init_pllu()
Because the preemption is disabled in the start_kernel before calling
time_init, tegra210_init_pllu is actually in an atomic context while
it includes a readl_relaxed_poll_timeout that might sleep.
So this patch just changes this readl_relaxed_poll_timeout() to its
atomic version.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Acked-By: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ming Lei [Sat, 14 Oct 2017 09:22:25 +0000 (17:22 +0800)]
blk-mq-sched: dispatch from scheduler IFF progress is made in ->dispatch
[ Upstream commit
5e3d02bbafad38975099b5848f5ebadedcf7bb7e ]
When the hw queue is busy, we shouldn't take requests from the scheduler
queue any more, otherwise it is difficult to do IO merge.
This patch fixes the awful IO performance on some SCSI devices(lpfc,
qla2xxx, ...) when mq-deadline/kyber is used by not taking requests if
hw queue is busy.
Reviewed-by: Omar Sandoval <osandov@fb.com>
Reviewed-by: Bart Van Assche <bart.vanassche@wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Leo Yan [Fri, 1 Sep 2017 00:47:14 +0000 (08:47 +0800)]
clk: hi6220: mark clock cs_atb_syspll as critical
[ Upstream commit
d2a3671ebe6479483a12f94fcca63c058d95ad64 ]
Clock cs_atb_syspll is pll used for coresight trace bus; when clock
cs_atb_syspll is disabled and operates its child clock node cs_atb
results in system hang. So mark clock cs_atb_syspll as critical to
keep it enabled.
Cc: Guodong Xu <guodong.xu@linaro.org>
Cc: Zhangfei Gao <zhangfei.gao@linaro.org>
Cc: Haojian Zhuang <haojian.zhuang@linaro.org>
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/
1504226835-2115-2-git-send-email-leo.yan@linaro.org
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mauro Carvalho Chehab [Wed, 1 Nov 2017 12:09:59 +0000 (08:09 -0400)]
media: camss-vfe: always initialize reg at vfe_set_xbar_cfg()
[ Upstream commit
9917fbcfa20ab987d6381fd0365665e5c1402d75 ]
if output->wm_num is bigger than 2, the value for reg is
not initialized, as warned by smatch:
drivers/media/platform/qcom/camss-8x16/camss-vfe.c:633 vfe_set_xbar_cfg() error: uninitialized symbol 'reg'.
drivers/media/platform/qcom/camss-8x16/camss-vfe.c:637 vfe_set_xbar_cfg() error: uninitialized symbol 'reg'.
That shouldn't happen in practice, so add a logic that will
break the loop if i > 1, fixing the warnings.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Acked-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sébastien Szymanski [Tue, 1 Aug 2017 10:40:07 +0000 (12:40 +0200)]
clk: imx6: refine hdmi_isfr's parent to make HDMI work on i.MX6 SoCs w/o VPU
[ Upstream commit
c68ee58d9ee7b856ac722f18f4f26579c8fbd2b4 ]
On i.MX6 SoCs without VPU (in my case MCIMX6D4AVT10AC), the hdmi driver
fails to probe:
[ 2.540030] dwhdmi-imx 120000.hdmi: Unsupported HDMI controller
(0000:00:00)
[ 2.548199] imx-drm display-subsystem: failed to bind 120000.hdmi
(ops dw_hdmi_imx_ops): -19
[ 2.557403] imx-drm display-subsystem: master bind failed: -19
That's because hdmi_isfr's parent, video_27m, is not correctly ungated.
As explained in commit
5ccc248cc537 ("ARM: imx6q: clk: Add support for
mipi_core_cfg clock as a shared clock gate"), video_27m is gated by
CCM_CCGR3[CG8].
On i.MX6 SoCs with VPU, the hdmi is working thanks to the
CCM_CMEOR[mod_en_ov_vpu] bit which makes the video_27m ungated whatever
is in CCM_CCGR3[CG8]. The issue can be reproduced by setting
CCMEOR[mod_en_ov_vpu] to 0.
Make the HDMI work in every case by setting hdmi_isfr's parent to
mipi_core_cfg.
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adriana Reus [Mon, 2 Oct 2017 10:32:10 +0000 (13:32 +0300)]
clk: imx: imx7d: Fix parent clock for OCRAM_CLK
[ Upstream commit
edc5a8e754aba9c6eaeddd18cb1e72462f99b16c ]
The parent of OCRAM_CLK should be axi_main_root_clk
and not axi_post_div.
before:
axi_src 1 1
332307692 0 0
axi_cg 1 1
332307692 0 0
axi_pre_div 1 1
332307692 0 0
axi_post_div 1 1
332307692 0 0
ocram_clk 0 0
332307692 0 0
main_axi_root_clk 1 1
332307692 0 0
after:
axi_src 1 1
332307692 0 0
axi_cg 1 1
332307692 0 0
axi_pre_div 1 1
332307692 0 0
axi_post_div 1 1
332307692 0 0
main_axi_root_clk 1 1
332307692 0 0
ocram_clk 0 0
332307692 0 0
Reference Doc: i.MX 7D Reference Manual - Chap 5, p 516
(https://www.nxp.com/docs/en/reference-manual/IMX7DRM.pdf)
Fixes:
8f6d8094b215 ("ARM: imx: add imx7d clk tree support")
Signed-off-by: Adriana Reus <adriana.reus@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Chen Zhong [Thu, 5 Oct 2017 03:50:23 +0000 (11:50 +0800)]
clk: mediatek: add the option for determining PLL source clock
[ Upstream commit
c955bf3998efa3355790a4d8c82874582f1bc727 ]
Since the previous setup always sets the PLL using crystal 26MHz, this
doesn't always happen in every MediaTek platform. So the patch added
flexibility for assigning extra member for determining the PLL source
clock.
Signed-off-by: Chen Zhong <chen.zhong@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hans de Goede [Thu, 2 Nov 2017 09:30:11 +0000 (10:30 +0100)]
staging: rtl8188eu: Revert part of "staging: rtl8188eu: fix comments with lines over 80 characters"
[ Upstream commit
4004a9870bbefdb6644c3d2033f5315920a3b669 ]
Commit
74e1e498e84e ("staging: rtl8188eu: fix comments with lines over 80
characters") not only changed comments but also changed an if check:
-if (pmlmepriv->cur_network.join_res != true) {
+if (!(pmlmepriv->cur_network.join_res)) {
This is not equivalent as join_res is an int and can have values such
as -2 and -3.
Note for the next time, please only make one type of changes in a single
clean-up commit.
Fixes:
74e1e498e84e ("staging: rtl8188eu: fix comments with lines over 80 ...")
Cc: Juliana Rodrigues <juliana.orod@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
qumingguang [Thu, 2 Nov 2017 12:45:22 +0000 (20:45 +0800)]
net: hns3: Fix a misuse to devm_free_irq
[ Upstream commit
ae064e6123f89f90af7e4ea190cc0c612643ca93 ]
we should use free_irq to free the nic irq during the unloading time.
because we use request_irq to apply it when nic up. It will crash if
up net device after reset the port. This patch fixes the issue.
Signed-off-by: qumingguang <qumingguang@huawei.com>
Signed-off-by: Lipeng <lipeng321@huawei.com>
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fuyun Liang [Fri, 3 Nov 2017 04:18:26 +0000 (12:18 +0800)]
net: hns3: fix for getting advertised_caps in hns3_get_link_ksettings
[ Upstream commit
2b39cabb2a283cea0c3d96d9370575371726164f ]
This patch fixes a bug for ethtool's get_link_ksettings().
The advertising for autoneg is always added to advertised_caps
whether autoneg is enable or disable. This patch fixes it.
Fixes: 496d03e (net: hns3: Add Ethtool support to HNS3 driver)
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Lipeng <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jan Kara [Fri, 3 Nov 2017 11:21:21 +0000 (12:21 +0100)]
mm: Handle 0 flags in _calc_vm_trans() macro
[ Upstream commit
592e254502041f953e84d091eae2c68cba04c10b ]
_calc_vm_trans() does not handle the situation when some of the passed
flags are 0 (which can happen if these VM flags do not make sense for
the architecture). Improve the _calc_vm_trans() macro to return 0 in
such situation. Since all passed flags are constant, this does not add
any runtime overhead.
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Robert Baronescu [Tue, 10 Oct 2017 10:22:00 +0000 (13:22 +0300)]
crypto: tcrypt - fix buffer lengths in test_aead_speed()
[ Upstream commit
7aacbfcb331ceff3ac43096d563a1f93ed46e35e ]
Fix the way the length of the buffers used for
encryption / decryption are computed.
For e.g. in case of encryption, input buffer does not contain
an authentication tag.
Signed-off-by: Robert Baronescu <robert.baronescu@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Suzuki K Poulose [Fri, 3 Nov 2017 11:45:18 +0000 (11:45 +0000)]
arm-ccn: perf: Prevent module unload while PMU is in use
[ Upstream commit
c7f5828bf77dcbd61d51f4736c1d5aa35663fbb4 ]
When the PMU driver is built as a module, the perf expects the
pmu->module to be valid, so that the driver is prevented from
being unloaded while it is in use. Fix the CCN pmu driver to
fill in this field.
Fixes:
a33b0daab73a0 ("bus: ARM CCN PMU driver")
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Eryu Guan [Thu, 2 Nov 2017 04:43:50 +0000 (21:43 -0700)]
xfs: truncate pagecache before writeback in xfs_setattr_size()
[ Upstream commit
350976ae21873b0d36584ea005076356431b8f79 ]
On truncate down, if new size is not block size aligned, we zero the
rest of block to avoid exposing stale data to user, and
iomap_truncate_page() skips zeroing if the range is already in
unwritten state or a hole. Then we writeback from on-disk i_size to
the new size if this range hasn't been written to disk yet, and
truncate page cache beyond new EOF and set in-core i_size.
The problem is that we could write data between di_size and newsize
before removing the page cache beyond newsize, as the extents may
still be in unwritten state right after a buffer write. As such, the
page of data that newsize lies in has not been zeroed by page cache
invalidation before it is written, and xfs_do_writepage() hasn't
triggered it's "zero data beyond EOF" case because we haven't
updated in-core i_size yet. Then a subsequent mmap read could see
non-zeros past EOF.
I occasionally see this in fsx runs in fstests generic/112, a
simplified fsx operation sequence is like (assuming 4k block size
xfs):
fallocate 0x0 0x1000 0x0 keep_size
write 0x0 0x1000 0x0
truncate 0x0 0x800 0x1000
punch_hole 0x0 0x800 0x800
mapread 0x0 0x800 0x800
where fallocate allocates unwritten extent but doesn't update
i_size, buffer write populates the page cache and extent is still
unwritten, truncate skips zeroing page past new EOF and writes the
page to disk, punch_hole invalidates the page cache, at last mapread
reads the block back and sees non-zero beyond EOF.
Fix it by moving truncate_setsize() to before writeback so the page
cache invalidation zeros the partial page at the new EOF. This also
triggers "zero data beyond EOF" in xfs_do_writepage() at writeback
time, because newsize has been set and page straddles the newsize.
Also fixed the wrong 'end' param of filemap_write_and_wait_range()
call while we're at it, the 'end' is inclusive and should be
'newsize - 1'.
Suggested-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Eryu Guan <eguan@redhat.com>
Acked-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Gary R Hook [Fri, 3 Nov 2017 16:50:34 +0000 (10:50 -0600)]
iommu/amd: Limit the IOVA page range to the specified addresses
[ Upstream commit
b92b4fb5c14257c0e7eae291ecc1f7b1962e1699 ]
The extent of pages specified when applying a reserved region should
include up to the last page of the range, but not the page following
the range.
Signed-off-by: Gary R Hook <gary.hook@amd.com>
Fixes:
8d54d6c8b8f3 ('iommu/amd: Implement apply_dm_region call-back')
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Liu Bo [Fri, 3 Nov 2017 17:24:44 +0000 (11:24 -0600)]
badblocks: fix wrong return value in badblocks_set if badblocks are disabled
[ Upstream commit
39b4954c0a1556f8f7f1fdcf59a227117fcd8a0b ]
MD's rdev_set_badblocks() expects that badblocks_set() returns 1 if
badblocks are disabled, otherwise, rdev_set_badblocks() will record
superblock changes and return success in that case and md will fail to
report an IO error which it should.
This bug has existed since badblocks were introduced in commit
9e0e252a048b ("badblocks: Add core badblock management code").
Signed-off-by: Liu Bo <bo.li.liu@oracle.com>
Acked-by: Guoqing Jiang <gqjiang@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jiang Yi [Fri, 11 Aug 2017 03:29:44 +0000 (11:29 +0800)]
target/file: Do not return error for UNMAP if length is zero
[ Upstream commit
594e25e73440863981032d76c9b1e33409ceff6e ]
The function fd_execute_unmap() in target_core_file.c calles
ret = file->f_op->fallocate(file, mode, pos, len);
Some filesystems implement fallocate() to return error if
length is zero (e.g. btrfs) but according to SCSI Block
Commands spec UNMAP should return success for zero length.
Signed-off-by: Jiang Yi <jiangyilism@gmail.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tangwenji [Thu, 24 Aug 2017 11:59:37 +0000 (19:59 +0800)]
target:fix condition return in core_pr_dump_initiator_port()
[ Upstream commit
24528f089d0a444070aa4f715ace537e8d6bf168 ]
When is pr_reg->isid_present_at_reg is false,this function should return.
This fixes a regression originally introduced by:
commit
d2843c173ee53cf4c12e7dfedc069a5bc76f0ac5
Author: Andy Grover <agrover@redhat.com>
Date: Thu May 16 10:40:55 2013 -0700
target: Alter core_pr_dump_initiator_port for ease of use
Signed-off-by: tangwenji <tang.wenji@zte.com.cn>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tangwenji [Fri, 15 Sep 2017 08:03:13 +0000 (16:03 +0800)]
iscsi-target: fix memory leak in lio_target_tiqn_addtpg()
[ Upstream commit
12d5a43b2dffb6cd28062b4e19024f7982393288 ]
tpg must free when call core_tpg_register() return fail
Signed-off-by: tangwenji <tang.wenji@zte.com.cn>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / platform / kernel / linux-exynos.git / log